Mitsubishi Heavy Industries | SRK63CE-S1 | User`s manual | Mitsubishi Heavy Industries SRK63CE-S1 User`s manual

USER’S MANUAL
MITSUBISHI DAIYA
ROOM AIR-CONDITIONER
ENGLISH
MANUEL DE L’UTILISATEUR
FRANÇAIS
CLIMATISEUR D’INTERIEUR
ANWENDERHANDBUCH
DEUTSCH
¨T
BETRIEBSEINHEIT KLIMAGERA
SRK63HE-S
SRK71HE-S
ISTRUZIONI PER L’USO
ITALIANO
CONDIZIONATORE D’ARIA COMPATTO
SRK63CE-S
SRK71CE-S
MANUAL DEL PROPIETARIO
ESPAN˜OL
ACONDICIONADOR AMBIENTAL DE AIRE INCORPORADO
GEBRUIKERSHANDLEIDING
NEDERLANDS
KAMER-AIR-CONDITIONING
MANUAL DO UTILIZADOR
PORTUGUÊS
APARELHO DE AR CONDICIONADO DE INTERIOR
√¢∏°π∂™ Ã∏™∏™
∂§§∏¡π∫∞
∫§πª∞∆π™∆π∫√ ∂™ø∆∂ƒπ∫√À Ãøƒ√À
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
РУССКИЙ
КОМНАТНЫЙ КОНДИЦИОНЕР ВОЗДУХА
KULLANIM KILAVUZU
TÜRKÇE
SPL‹T KL‹MA
AIR-CONDITIONING & REFRIGERATION SYSTEMS HEADQUARTERS
16-5, 2-Chome, Kounan, Minato-ku, Tokyo, 108-8215, Japan
Fax: (03) 6716-5926
MITSUBISHI HEAVY INDUSTRIES EUROPE, LTD.
AIR-CONDITIONER DIVISION
3rd Floor Thavies Inn House 3-4 Holborn Circus London EC1N 2HA, ENGLAND
Phone: 44(0)20 7842 8171
Fax: 44(0)20 7842 8104
RKW012A202_Cover.p65
1
This air conditioner complies with EMC Directive 89/336/EEC, LV
Directive 73/23/EEC.
Este acondicionador de aire cumple con la directiva EMC: 89/
336/EEC, LV Directiva 73/23/EEC.
Ce climatiseur est conforme à la Directive EMC: 89/336/EEC, LV
Directive 73/23/EEC.
Deze airconditioner voldoet aan EMC Directive 89/336/EEC, LV
Directive 73/23/EEC.
Dieses Kimagerät erfüllt die EMC Direktiven 89/336/EEC, LV
Direktiven 73/23/EEC.
Este aparelho de ar condicionado está em conformidade com a
Directiva EMC 88/336/CEE e a Directiva LV 72/23/CEE.
Questo condizionatore d’aria è conforme alla Direttiva EMC: 89/
336/EEC, LV Direttiva 73/23/EEC.
∞˘Ùfi ÙÔ ÎÏÈÌ·ÙÈÛÙÈÎfi Â›Ó·È Û‡ÌʈÓÔ Ì ÙȘ ÚԉȷÁڷʤ˜ Ù˘
√‰ËÁ›·˜ EMC 88/396 Î·È Ù˘ √‰ËÁ›·˜ LV 73/23 Ù˘ ∂√∫.
RKW012A202
05.2.23, 9:31
Thank you for purchasing a Mitsubishi Daiya Air-Conditioner. To get the best long-lasting
performance, read and follow this User’s Manual carefully before using your air-conditioner. After reading, please store the Manual in a safe place and refer to it for operational
questions or in the event of any irregularities.
This air-conditioner is intended for domestic use.
This instruction manual contains the explanation of the heatpump air-conditioner.
That of cooling-only air-conditioner shall be referred to the same explanation , with
neglecting the information on heating-operation mode.
ENGLISH
An alternative refrigerant (R410A) is used in this air-conditioner. When asking the
dealer for service or inspection and maintenance, explain the dealer about this matter.
contents
Safety precautions......................................................................................................................... 2
Choice of operations and features ................................................................................................ 4
Name of each part and its function ............................................................................................... 5
Operation and indication section for remote control .................................................................... 7
AUTO mode operation procedure ................................................................................................ 8
Temperature adjustment during AUTO ........................................................................................ 8
About FAN SPEED ...................................................................................................................... 8
COOL/HEAT/DRY/FAN mode operation procedure .................................................................. 9
Air-conditioner operating conditions............................................................................................ 9
Characteristics of HEAT mode operation .................................................................................... 9
Air flow direction adjustment procedure .................................................................................... 10
SLEEP operation procedure ....................................................................................................... 11
OFF-TIMER operation procedure .............................................................................................. 11
ON-TIMER operation procedure................................................................................................ 12
SLEEP operation + ON-TIMER operation procedure ............................................................... 12
PROGRAM TIMER operation procedure .................................................................................. 13
Present time setting procedure .................................................................................................... 13
HIGH POWER/ECONOMY operation procedure ..................................................................... 14
Concerning CLEAN operation ................................................................................................... 15
Emergency run operation............................................................................................................ 15
Power blackout auto restart function .......................................................................................... 15
Remote control handling procedure ........................................................................................... 16
When the operation fails with the remote control ...................................................................... 16
Operating hints ........................................................................................................................... 17
Maintenance................................................................................................................................ 17
Has the unit been installed correctly? ......................................................................................... 19
Troubleshooting .......................................................................................................................... 19
Please remember! ....................................................................................................................... 20
When to contact your distributor without delay ......................................................................... 21
Self diagnosis function ............................................................................................................... 21
–1–
RKW012A202_En.p65
1
05.2.23, 10:52
Safety precautions
• Before starting to use the system, please read these “Safety precautions” carefully to ensure proper operation of the system.
• The safety precautions are classified as “ DANGER” and “ CAUTION”. Precautions as shown in the column “ DANGER” indicate that
improper handling could have dramatic consequences like death, serious injury, etc. Nevertheless, even precautions as shown in the column
“ CAUTION” might pose a serious problem, depending on the circumstances. Please observe these precautions with great care, since they are
essential to your safety.
• Symbols which appear frequently in the text have the following meaning:
Strictly prohibited
Observe instructions with
great care
Provide positive earthing
• When you have read the instruction manual, please keep it near at hand for consultation. If someone else takes over as operator, make certain that the
manual is also passed on to the new operator.
❚ INSTALLATION PRECAUTIONS
DANGER
The system is meant for domestic, residential etc. use.
The system must be installed by your dealer or a qualified professional.
If used in inferior environments, such as an engineering workplace, the equipment
may function poorly.
It is not advisable to install the system yourself, as faulty handling may cause leakage of water, electric shock or fire.
CAUTION
Do not install near places where inflammable gas may leak.
Depending on the place of installation, a circuit breaker may
be necessary.
LPG
Gas leaks may cause fire.
If you don’t fit a circuit breaker, you may cause an electric shock.
Make sure that you drain the hose properly, so that all the
water has dripped out.
Make sure that the system has been properly earthed.
Earth cables should never be connected to a gas pipe, municipal water pipe, lightning conductor or telephone earth cable. Incorrect installation of the earth cable
may produce an electric shock.
Negligence may cause flooding in the room resulting in wet furniture.
❚ OPERATION PRECAUTIONS
DANGER
Do not expose yourself to the cooling air for prolonged periods.
Do not insert anything into the air inlet.
This could affect your physical condition and cause health problems.
This may cause injury, as the internal fan rotates at high speed.
Store the remote controller out of reach of infants.
Failure to observe this may result in the batteries
being swallowed or other accidents.
–2–
RKW012A202_En.p65
2
05.2.23, 10:52
Safety precautions
CAUTION
Only use approved fuses.
Do not handle the switches with wet
hands.
Don’t swing from the system.
Use of steel or copper wire instead of an approved
fuse is strictly forbidden, as it may cause a breakdown
or fire.
This may cause an electric shock.
If the system falls down,
you may get injured.
Do not place a combustible insecticide
or paint spray near the blower, nor aim it
directly at the system.
You should not expose any combustion appliance directly to the air
stream of the air-conditioner.
Do not wash the air-conditioner with water.
This may result in a fire.
The appliance may then work inadequately.
This could cause an electric shock.
The system should only be used for its original purpose
and not for anything else like, for instance, preservation of
food, plants or animals, precision devices or works of art.
Do not place anything containing water, like vases, on top of the unit.
Do not install the system at a place
where the air stream of the blower is
aimed directly at plants or animals.
The system is only intended for use in ordinary domestic rooms.
Any other use of the system may damage the quality of food, etc.
Water entering the unit could damage the insulation and therefore cause an electric shock.
This will damage their health.
Do not sit on the outdoor unit nor put
anything on it.
After a long period of use, check the unit's
support structure from time to time.
Do not touch the aluminum fins on the
air heat exchanger.
If the unit falls down or things drop off it, people
could get hurt.
If you don't repair any damage straightaway, the
unit may fall down and cause personal injury.
Failure to observe this may result in injury.
If you operate the system together with
a combustion appliance, you must regularly ventilate the indoor air.
Stand firmly on a stepladder or other
stable object when removing the inlet
panel and filters.
When you clean the system, stop the
unit and turn off the power switch.
Insufficient ventilation may cause accidents due to
oxygen deficiency.
Failure to observe this may result in injury through
insecure objects toppling over.
Never clean the unit while the internal fan is rotating.
❚ PRECAUTIONS FOR TRANSFER OR REPAIRS
DANGER
Consult your dealer for repairs to the
system.
If the air-conditioner is moved elsewhere, contact your dealer or a professional fitter.
If you notice anything abnormal (smell of
burning, etc.), stop the system, turn off the
power switch and consult your dealer.
Wrong repairs could cause an electric shock, fire, etc.
Faulty installation may cause water leakage, electric shock, fire, etc.
Continued use of the system in abnormal circumstances may result in malfunctioning, electric shock,
fire, etc.
–3–
RKW012A202_En.p65
3
05.2.23, 10:52
Choice of operations and features
Choice of operations
HEAT
Page 9
Page 9
COOL
The unit draws in heat from the outside air,
transfers it inside and heats the room.
Cooling by extracting heat from the room.
DRY
Page 9
Drying by extracting damp from the room.
Functioning of micro-computer depends on
setting and room temperatures. It dehumidifies while keeping room temperature almost
constant.
FAN
Page 9
Page 8
AUTO
Fanning by circulating room air.
Automatic selection of operating mode.
The Auto mode automatically selects the
operation mode (HEAT, COOL or DRY),
depending on the room temperature when
switched on.
Features
Amenity facility
Page 13
When using the timer to switch on, the system should become operational shortly before the set time, depending on the room
temperature so that the desired temperature
should be reached at the set time.
Adjustment of
airflow
TIMER procedure
Page 11, 12
There are three timers, for SLEEP, ON and
OFF. They can be set as desired.
Page 10
HIGH POWER mode
Page 14
Turning up the power operates the air conditioner in the power cooling and heating
mode.
ECONOMY mode
Page 14
• MULTI-DIRECTIONAL AIR FLOW
This function sets the unit at the most suitable angle
for blowing, imitating a natural breeze.
• SWING FLAP
Flap moves up and down continuously.
• SWING LOUVER
Louver moves left and right continuously.
• MEMORY FLAP (FLAP OR LOUVER STOPPED)
Once the flap or louver position has been set, the unit
will memorise it and continue in the same position
the next time.
This is an economic level of operation.
–4–
RKW012A202_En.p65
4
05.2.23, 10:52
Name of each part and its function
INDOOR UNIT
SRK63HE-S
SRK71HE-S
SRK63CE-S
SRK71CE-S
Air inlet panel
Draws in the indoor air.
Unit indication section and remote control signal receiver
Wireless remote control
Air filter
Removes dust or dirt from the inlet air.
Page 17
Photocatalytic washable deodorizing filter
Natural enzyme filter
Room temperature detector
Unit operation switch
Air outlet
Air blows out of here.
Left/right air flow adjustment louver
Page 10
Up/down air flow direction adjustment flap
Page 10
Drain hose
Drains water from the dehumidified air.
Refrigerant piping connection electric flex
OUTDOOR UNIT
SRC63HE-S
SRC71HE-S
Accessories
SRC63CE-S
SRC71CE-S
Battery (R03×2)
Air inlet
(on side & rear surface)
Wood screw (Quantity:2)
(for remote control holder mounting)
Wireless remote control
Wireless remote
control holder
Natural enzyme filter
(green)
Air outlet
* The appearance varies for Models 63 and 71.
–5–
RKW012A202_En.p65
5
05.2.23, 10:52
Photocatalytic washable deodorizing filter (orange)
Unit indication section
RUN (HOT KEEP) light (green)
• Illuminates during operation.
• Blinks at air flow stop due to the ‘HOT KEEP’
and ‘CLEAN operation’.
1.5 sec.
ON
HOT KEEP
OFF
0.5 sec.
3 sec.
ON
CLEAN operation
OFF
1 sec.
HI POWER light (green)
Illuminates during HIGH POWER operation.
Page 20
ECONOMY light (orange)
TIMER light (yellow)
Illuminates during ECONOMY operation.
Illuminates during TIMER operation.
How to open the air inlet panel
Unit ON/OFF button
In emergencies, this button can be used for turning on/off the unit when re-
Place fingers at the recesses on both sides of the panel and pull up the panel
to this side so that it will be opened by about 60 degrees.
mote control is not available.
Page 15
Unit ON/OFF button
How to close the air inlet panel
Push both sides evenly and press further lightly at the center.
Removal, installation of air inlet panel
When removing the air inlet panel for internal cleaning or others, open the
panel by 80 degrees and then pull it to this side.
Secure either the upper or lower edge of the air inlet panel by lightly pushing it
in, and then close the panel.
–6–
RKW012A202_En.p65
6
05.2.23, 15:03
Operation and indication section for remote control
Operation section
FAN SPEED button
OPERATION MODE select button
Each time the button is pushed, the
cator is switched over in turn.
indi-
Each time the button is pushed, the
cator is switched over in turn.
indi-
ON/OFF (luminous) button
HI POWER/ECONO button
Press for starting operation, press again for
stopping.
This button changes the HIGH POWER/
ECONOMY mode.
Page 14
AIR FLOW (UP/DOWN) button
This button changes the air flow (up/down) mode.
Page 10
TEMPERATURE button
This button sets the room temperature.
(This button changes the present time and
TIMER time.)
AIR FLOW (LEFT/RIGHT) button
This button changes the air flow (left/right) mode.
Page 10
CANCEL button
SLEEP button
This button cancels the ON timer, OFF
timer, and SLEEP operation.
This button changes to SLEEP operation.
Page 11
OFF TIMER button
This button selects OFF TIMER operation.
CLEAN switch
Page 11
This switch changes the CLEAN mode.
Page 15
RESET switch
Switch for resetting microcomputer.
Page 16
• The above illustration shows all controls, but in practice
only the relevant parts are shown.
ON TIMER button
This button selects ON TIMER operation.
TIME SET UP switch
This switch for setting the time.
Page 12
Page 13
Indication section
ON/OFF TIMER indicator
SLEEP indicator
Indicates during ON/OFF TIMER operation.
Indicates during SLEEP operation.
OPERATION MODE indicator
Indicates selected operation with lamp.
HE type:
[ (Auto) • (Cool) •
(Heat) • (Dry)]
CE type:
[ (Auto) • (Cool) •
(Fan) • (Dry)]
TEMPERATURE indicator
Indicates set temperature.
(Does not indicate temperature when operation
mode is on AUTO)
TIME indicator
Indicates present time or timer setting time.
FAN SPEED indicator
Indicates set air flow rate with
lamp.
AIR FLOW indicator
Shows selected flap and louver mode.
CLEAN indicator
HI POWER/ECONO MODE indicator
Indicates during CLEAN operation.
Indicates during HIGH POWER/ECONOMY
mode operation.
Transmission procedure
When each button on the remote control is pressed – with the remote control pointing towards the air-conditioner unit – a signal is transmitted.
When the air-conditioner receives the signal correctly, it will beep.
–7–
RKW012A202_En.p65
7
05.2.23, 10:52
AUTO mode operation procedure
■ Automatically selects the operation mode (HE type: HEAT, DRY, COOL/CE type: COOL, DRY) depending on the room temperature when switched on.
When the unit is not in AUTO mode:
Aim the remote control at the air-conditioner.
1
Press MODE button.
Move the [
2
mark] to the
(Auto) position.
If the air-conditioner is not operating
Press the ON/OFF button.
To stop:
NOTE
Press the ON/OFF button.
AUTO mode can be
operated by simply
pressing the ON/OFF
button.
• Air is not blown out during the operation.
Page 20
• If you don’t want the AUTO mode program, change to
COOL,HEAT, DRY or FAN instead of AUTO.
Air flow direction adjustment
procedure.
Page 9
Page 10
Temperature adjustment during AUTO
■ Air temperature adjustment is possible even during automatic operation. There are 6 levels of adjustment possible with the
button or the
button.
When a change in temperature is desired.
Aim the remote control at the air-conditioner.
1
Press the
or
button.
When it is a little cold
Press the
button.
■ Each time the
button is pressed, the switch over occurs in the following order
–6 → –5 → ............ –1 → ±0 → +1 ............ +6.
When +6 is indicated, even if the
button is pressed, the indicator does not change.
When it is a little hot
Press the
button.
■ Each time the
button is pressed, the switch over occurs in the following order
+6 → +5 → ............ +1 → ±0 → –1 ............ –6.
When –6 is indicated, even if the button is pressed, the indicator does not change.
About FAN SPEED
■ You can choose the capacity of your air-conditioner when heating, cooling or fan.
Operation capacity by your choice
FAN SPEED
Set automatically by microcomputer
AUTO
Powerful operation with high capacity
Standard operation
Energy-saving operation
HI
MED
LO
Aim the remote control at the air-conditioner.
Press the FAN SPEED button.
Move the [
AUTO
mark] to the desirable fan speed position.
HI
MED
–8–
RKW012A202_En.p65
8
05.2.23, 10:53
LO
COOL/HEAT/DRY/FAN mode operation procedure
Aim the remote control at the air-conditioner.
1
Press the MODE select button.
Move the [
2
3
mark] to the desirable operation position.
(Cool),
(Cool),
HE type:
CE type:
(Heat), (Dry)
(Fan), (Dry)
If the air-conditioner is not operating
Press the ON/OFF button.
Press the TEMP button.
Press
or
button for the desired temperature.
4
Air flow direction adjustment procedure.
21°C~24°C
FAN
22°C~24°C
DRY
26°C~28°C
HEAT
COOL
Standard
——
Press the FAN SPEED button
Set the fan speed as desired.
Page 10
To stop:
NOTE
Press the ON/OFF button.
Program changing procedure
Set the new program.
• The operation program can also be set or changed when
the air-conditioner is not in operation.
• Air is not blown out during the operation.
Page 20
Air-conditioner operating conditions
■ Use within the following operational range. Operating outside of this range may result in the protection devices being activated, preventing the
unit from working.
Cooling operation
Heating operation
Outside temperature Approximately 21 to 43 °C
Inside temperature
Inside humidity
Approximately -5 to 21 °C
Approximately 21 to 32 °C
Approximately 15 to 30 °C
Below approximately 80%
The long-term use of the unit with a humidity level
exceeding 80% may result in condensation forming on the
surface of the indoor unit, leading to water drips.
—
Characteristics of HEAT mode operation
Mechanism and capacity of HEAT mode operation
■ Mechanism
• The unit draws in heat from the cold outside air, transfers it indoors and heats the room. The heating capacity of the heat pump mechanism decreases
when the outside air temperature gets colder.
• The hot air circulation system takes a while before warming up the room temperature.
• If the outside temperature becomes extremely low, it would be better to use an additional source of heating.
Defrosting
If the outside temperature becomes low and humidity is high, the heat exchanger in the outdoor unit may frost over, which prevents efficient heating.
If this happens, the automatic defroster is activated and during defrosting the heating operation stops for 5 to 10 minutes.
• Both indoor and outdoor fans stop and the RUN light (green) blinks slowly (1.5 sec. ON, 0.5 sec. OFF) during defrosting.
• The outdoor unit may give off some steam during defrosting. This is to help the defrosting process and is not a defect.
• The HEAT operation resumes as soon as defrosting has been completed.
–9–
RKW012A202_En.p65
9
05.2.23, 10:53
Air flow direction adjustment procedure
Adjusting air flow direction
■ Up/down direction can be adjusted with the AIRFLOW
the mode changes as follows:
Change to AIRFLOW (UP/DOWN) mode.
(UP/DOWN) button on the remote control. Each time when you press this button
(Flap stopped)
(Swing)
■ Left/right direction can be adjusted with the AIRFLOW
button the mode changes as follows:
Change to AIRFLOW (LEFT/RIGHT) mode.
(LEFT/RIGHT) button on the remote control. Each time when you press this
(Louver stopped)
(Swing)
NOTE
• When heating operation starts, the cold air outlet is blocked, so the flap and louver move to the horizontal / center position, and resume the position that was set
after the warm air output begins.
• When the compressor stops because the room temperature is higher than the temperature setting and it is in DEFROSTING operation, the flap and louvers will be
in the horizontal / center position.
• The air flow direction cannot be set in the instances above. Change the air flow direction settings after the warm air starts flowing and it moves to the airflow
direction that had been set.
Multi-directional Air Flow (up/down air scroll and left/right air scroll)
■ Activating both up/down air swing and left/right air swing at the same time results in a multi-directional air flow.
Up/down air scroll
In COOL, DRY and FAN operation
Thick line
In HEAT operation
In COOL, DRY and FAN operation
In HEAT operation
Stops at this position
for 5 seconds.
Stops at this position
for 5 seconds.
Thin line
Left/right air scroll
: moves quickly
Left louver
Right louver
: moves slowly
MEMORY FLAP (FLAP OR LOUVER STOPPED)
When you press the AIRFLOW (UP/DOWN or LEFT/RIGHT) button once while the flap or louver is
operating, it stops swinging at an angle.Since this angle is memorized in the microcomputer, the flap or
louver will automatically be set at this angle when the next operation is started.
DANGER
• Avoid constant airflow to the body for hours on end.
• Recommended angle of the flap when stopping
HEAT
CAUTION
• When in COOL or DRY operation, do not operate for hours on end with the air
flow blowing straight down. Otherwise, condensation may appear on the outlet
grill and drip down.
• Do not try to adjust the flaps and louvers by hand, as the control angle may
change or the flap or louver may not close properly.
COOL, DRY
– 10 –
RKW012A202_En.p65
10
05.2.23, 10:53
(Slant forward
blowing)
(Horizontal
blowing)
SLEEP operation procedure
■ The unit stops automatically at the end of the set period of time.
The room temperature is automatically controlled when the set time lapses, so that the room does not become too cold during cooling or too warm
Aim the remote control at the air-conditioner.
Page 13
during heating.
1
Press the SLEEP button.
■ If this is pressed while the unit is off
SLEEP operation starts with the previous operation settings, and the air conditioning is
turned off after the time that has been set passes.
■ If this is pressed while the unit is running
Each time the button is pressed, the indication changes as follows:
... (Units of one hour)
No indication
(cancelled)
Example: You wish it to stop after 7 hours.
Set to
The timer light (yellow) is on.
1
h
• The unit stops at the end of the set period of time.
Changing of set time
Releasing procedure
Set to a new time by using SLEEP button.
Press the CANCEL button to turn off the SLEEP indicator.
OFF-TIMER operation procedure
■ The unit stops automatically at the end of the set period of time. If it is stopped, perform the operations starting with STEP 1 and if running start with STEP 2.
Example: You wish it to stop 22:30.
Aim the remote control at the air-conditioner.
1
2
If the air-conditioner is not operating
Press the ON/OFF button.
Press the OFF TIMER button.
OFF TIMER indicator
3
is blinking.
Press the “
or
Each time the
button is pressed, the indicator is switched in the order of:
0:00
0:10
Each time the
0:00
” button.
0:20
...
1:00
1:10
(Units of ten minutes)
button is pressed, the indicator is switched in the order of:
23:50
23:40
...
23:00
22:50
(Units of ten minutes)
Set at 22:30.
Changing of set time
Set a new time by using the OFF TIMER button.
4
Press within
60 sec.!
Press the OFF TIMER button.
The indication changes from blinking to steady lighting and the setting is complete.
The timer light (yellow) is on.
Releasing procedure
Press the CANCEL button to turn off the timer indicator.
h
• The unit stops at the end of the set period of time.
– 11 –
RKW012A202_En.p65
11
05.2.23, 10:57
ON-TIMER operation procedure
■ Operation starts 5 to 60 minutes before the time that is set so that the room temperature reaches the optimum temperature at that time.
ON-TIMER operation can be set regardless of whether the air-conditioner is running or not.
Page 13
Example: In the case you wish to bring the temperature to nearly set temperature in at 8:00.
Aim the remote control at the air-conditioner.
1
2
Press the ON-TIMER button.
ON TIMER indicator
is blinking.
Press the “
or
” button.
Each time the
button is pressed, the indicator is switched in the order of:
0:00
0:10
Each time the
0:00
0:20
...
1:00
1:10
(Units of ten minutes)
button is pressed, the indicator is switched in the order of:
23:50
...
23:40
23:00
22:50
(Units of ten minutes)
Set at 8:00.
3
Press the ON TIMER button.
Press within
60 sec.!
The indication changes from blinking to steady lighting and the setting is complete.
The timer light (yellow) is on.
h
• Operation starts 5 to 60 minutes before the set time.
• The TIMER light goes out at the set time.
Changing of set time
Releasing procedure
Set a new time by using the ON-TIMER button.
Press the CANCEL button to turn off the timer indicator.
SLEEP operation + ON-TIMER operation procedure
■ Combined timer operation of SLEEP operation and ON TIMER.
Example: When it is desired to stop after 3 hours and then start operation at 8:00, near
the set temperature.
■ SLEEP operation setting
Set by the procedures on page 11.
Set to
■ ON TIMER operation setting
Set by the above mentioned ON TIMER operation procedure.
Set to
The setting of the lighting of the timer light (yellow) of this unit is complete.
h
• After the SLEEP operation set time has elapsed, the operation stops, and it
starts form 5 to 60 minutes before the ON TIMER’s time.
• The timer light is not lit at the ON TIMER’s time.
Changing of set time
Releasing procedure
Set a new time by using the SLEEP or ON TIMER button.
Press the CANCEL button to turn off the timer indicator.
– 12 –
RKW012A202_En.p65
12
05.2.23, 10:58
PROGRAM TIMER operation procedure
■ The timer operations that consist of the combination of the timer being set at both on and off. Once this has been set and operations started,
operations will commence and end at the same time every day as long as the ON/OFF button is not pressed.
Example: When it is desired to stop at 22:30, and then start operation at 8:00, near the set
temperature.
■ OFF TIMER operation setting
Set by the procedures on page 11.
Set to
■ ON TIMER operation setting
Set by the procedures on page 12.
Set to
The setting of the lighting of the timer light (yellow) of this unit is complete.
The time will be displayed on the remote control unit. The display will change
depending on the operational status.
(Stopped)
(Operating)
Changing of set time
Set a new time by using the OFF TIMER or ON TIMER button.
Releasing procedure
Press the CANCEL button to turn off the timer indicator.
▼
About SLEEP operation
When SLEEP operation is selected, the room temperature is automatically
controlled after a while, ensuring that the room is not too cold during cooling
or too warm during heating.
• During COOL : the preset temperature is lowered by 1°C at the start of
SLEEP operation (when the timer is set). After that, the temperature goes
up by 1°C every an hour to become 2°C higher.
• During heating: Preset temperature is lowered by 1°C at the start of SLEEP
operation (when the timer is set). After that the temperature is lowered by
1°C every 30 minutes to become 3°C lower in an hour and 6°C lower in two
hours.
tions for COOL and HEAT operation mode (including AUTO).
It does not work for DRY mode.
Check the room
temp. 60 mins.
in advance.
▼
About Amenity facilities
Amenity facilities enable to start the operation a little earlier, so that the room
should approach optimum temperature at ON time when the operation is
started by ON-TIMER.
• Mechanism
The room temperature is checked
In COOL operation
60 minutes before the timer is at
(Stop) Operation starts
ON. Depending on the temperature at that time, the operation
starts 5 to 60 minutes before the
(Operation)
timer is at ON.
• The Amenity facility only func- Set temperature
Set time
Present time setting procedure
■ When inserting the batteries, the present time is automatically set to 13:00.
Example: Set to 10:30.
1
Press the TIME SET UP switch.
2
Press the “
3
Press the TIME SET UP switch.
Press with the tip of a ball pen, etc.
The time indicator blinks and can be set to the current time.
or
” button.
(Set to 10:30)
Press within
60 sec.!
The indication changes from blinking to steady lighting and the setting is complete.
NOTE
The timer operation is set on the basis of the present time, so please set it correctly.
– 13 –
RKW012A202_En.p65
13
05.2.23, 10:58
HIGH POWER/ECONOMY operation procedure
Aim the remote control at the air-conditioner.
1
2
If the air-conditioner is not operating
Press the ON/OFF button.
Press the HI POWER/ECONO button.
• When the operating mode is AUTO, COOL or HEAT
Each time the HI POWER/ECONO button is pressed, the indicator is switched
in the order of:
(HIGH POWER)
(ECONOMY)
No indication
(Normal operation)
• When the operating mode is DRY or PROGRAM TIMER
Each time the HI POWER/ECONO button is pressed, the indicator is switched
in the order of:
No indication
(Normal operation)
(ECONOMY)
Concerning HIGH POWER operation
Pressing the HI POWER/ECONO button intensifies the operating power and initiates powerful cooling or heating operation for 15 minutes
continuously. The remote controller
indicates but the FAN SPEED indication is erased.
NOTE
• During the HIGH POWER operation, the room temperature is not
controlled. When it causes an excessive cooling or heating,press
the HI POWER/ECONO button once more to cancel the HIGH
POWER operation.
• HIGH POWER operation is not available during the dehumidifying and the program timer operations.
• During ON timer operation, HIGH POWER operation will start
when the ON time is reached.
• When the following operations are conducted HIGH POWER operation will be canceled.
1 When the HI POWER/ECONO button is pressed again.
2 When the operation mode is changed.
3 When it has been 15 min. since HIGH POWER operation
has started.
Concerning ECONOMY operation
Pressing the HI POWER/ECONO button intlates a soft operation with the power suppressed in order to avoid an excessive cooling or heating. The
unit operates 1.5°C higher than the setting temperature for weak wind capacity during cooling or 2.5°C lower than that during heating. The remote
controller
indicates but the FAN SPEED indication is eraseed.
NOTE
• It will go into ECONOMY operation the next time the air-conditioner runs in the following instances.
1 When the air-conditioner is stopped using the ON/OFF button.
2 When the air-conditioner is stopped in SLEEP or OFF
TIMER operation.
3 When CLEAN operation ends.
• When the following operations are conducted ECONOMY operation will be canceled.
1 When the HI POWER/ECONO button is pressed again.
2 When the operation mode is changed dehumidifying to
fan.
– 14 –
RKW012A202_En.p65
14
05.2.23, 11:29
Concerning CLEAN operation
■ CLEAN operation should be run after AUTO, COOL and DRY operation to remove the moisture from inside the indoor unit and control the growth
of mold and bacteria.
Aim the remote control at the air-conditioner.
1
Press the CLEAN switch with the tip of a ballpoint pen.
Each time the CLEAN switch is pressed, the indicator is switched
in the order of:
No indication
(CLEAN off)
(CLEAN on)
To stop:
Press the ON/OFF button.
NOTE
• CLEAN operation is impossible after Heating, Fan and OFF-TIMER have
stopped.
• The indoor unit fan runs for about two hours in CLEAN operation.
• The RUN light flashes during CLEAN operation.
Emergency run operation
• The unit ON/OFF button on the unit operates ON/OFF temporarily when the remote control is not used.
Operation program
• OPERATION MODE :
AUTO
• FAN SPEED
:
AUTO
• AIR FLOW
:
AUTO
• Operation starts by pressing the unit ON/OFF button; it stops if you press
the button again.
Unit ON/OFF button
Power blackout auto restart function
■ What is power blackout auto restart function?
• Power blackout auto restart function is a function that records the operational status of the air-conditioner immediately prior to it being switched off
by a power cut, and then automatically resumes operations at that point after the power has been restored.
• The following settings will be cancelled:
1 Timer settings
2 HIGH POWER operations
NOTE
• The power blackout auto restart function is set at on when the air-conditioner is shipped from the factory. Consult with your dealer if this
function needs to be switched off.
• When power failure ocurrs, the timer setting is cancelled. Once power is resumed, reset the timer.
– 15 –
RKW012A202_En.p65
15
05.2.23, 10:59
Remote control handling procedure
Using the remote control holder
Replacing the batteries
The following cases signify exhausted batteries. Replace old batteries with new ones.
• Receiving beep is not emitted when a signal is transmitted.
• Indicator fades away.
1
Remove back lid and take out
old batteries.
3
Close back lid.
2
Insert new batteries.
(SUM-4 or R03x2)
4
Press the reset switch with the
tip of a ballpoint pen.
The remote control can be attached to a
wall or pillar by using a remote control
holder. Before installing the remote control, check that the air-conditioner receives the signals properly.
Attention to
the , and .
marks
For installing or removing the remote
control, move it up or down in the holder.
NOTE
When the indicator shows any abnormal condition, Press the reset switch
with the tip of a ballpoint pen.
• Don't use old and new batteries together.
• Remove the batteries when the remote control is not used for a
long period.
• The life of a battery conforming to JIS or IEC should be 6 to 12
months with normal use. If used longer, or when an unspecified
battery is used, liquid may leak from the battery, causing the remote control to malfunction.
• On the battery is printed its expected life. This may be shorter
than that of the air-conditioner, depending on the date of manufacture.
• However, the battery may still be in working order after expiry
of its nominal life.
Warning note for remote control handling
• Don’t go near high temperature
places, such as an electric carpet
or stove.
• Don’t leave the remote control exposed to direct sunlight or other
strong lighting.
• Don’t drop the remote control.
Handle with care.
• Don’t put any obstructing obstacles between the remote control
and the unit.
• Don’t spill water etc on the remote
control.
• Do not place heavy objects on the
remote controller, or step on it.
When the operation fails with the remote control
• Are the batteries running down?
"Replacing the batteries" above.
• If the operation still fails, handle as per emergency
run operation.
Contact your dealer.
Replace the batteries with new ones and repeat the operation.
– 16 –
RKW012A202_En.p65
16
05.2.23, 10:45
Page 15
Operating hints
■ Please observe the following for the most economic and comfortable use of your unit.
Set a suitable room temperature.
Clean the filters frequently.
Avoid direct sunlight and draught.
Excessively high or low temperatures are not
good for your health and waste electricity.
Clogged filters may block the air flow and
cause less efficient operation.
Cut out direct sunlight by drawing the curtains or blinds when cooling. Keep windows
and doors shut, except when ventilating.
Adjust the airflow direction properly.
Operate the unit only when needed.
Generate little heat when cooling.
Adjust the up/down and left/right airflow to
ensure a steady room temperature.
Use the timer properly to operate the unit
only when needed.
Keep heat sources out of the room as much as
possible.
suitable
temperature
Maintenance
Before maintenance
Turn off the power switch.
During the operational season
Cleaning the air filter
Standard interval is once every two week
1
Remove the air filter
2
Cleaning
1 Pull up to this side the air inlet panel.
2 Lightly hold the knobs at both sides and
lift a little to remove the panel to this
side.
• Don’t spill water.
There's a danger
of electric shock.
If the filter is very dirty, clean it with warm water
(approx. 30°C), and dry it thoroughly.
CAUTION
• Don’t clean the filters with boiling water.
• Don’t dry them over an open flame.
• Pull them out gently.
Wipe the unit with a soft,
dry cloth.
• Do not touch the aluminum fins on the heat
exchanger.
• Stand firmly on a stepladder or other stable
object when removing the inlet panel and filter.
Don’t use the following articles:
• Hot water (40°C or more)
It may deform or discolour the unit.
• Petrol, paint thinner, benzine or polishing agents,
etc.
They may deform or scratch the unit.
3
Reinstall the air filter
• Holding firmly the filter at both sides as shown at right
and insert securely.
• Operating without putting back the air filters will make
the unit dusty, and may cause damage.
Cleaning the unit
• Wipe the unit with a soft, dry cloth, or use a vacuum cleaner.
• If the unit is very dirty, wipe it with a cloth soaked in warm water.
Cleaning the air inlet panel
• Removal, installation of air inlet panel .
Page 6
• The panel can be washed with water. After washing with
water, wipe any moisture off the panel and dry out of
direct sunlight.
– 17 –
RKW012A202_En.p65
17
05.2.23, 10:45
Cooling/heating is affected by an air filter clogged up with dust etc., and the operation noise becomes louder. It may also
use extra electricity. Please clean the air filter at appropriate intervals.
NOTE
At the beginning of the season
At the end of the season
1
Set the temperature setting for approximately a half
day at 30°C and perform the cooling operation.
1
Make certain that there are no obstacles blocking the
air flow around the air intake and outlet openings of
the indoor and outdoor units.
2
3
4
5
6
Check the installation base for corrosion or rust.
Dry the inside of the unit.
2
Stop the unit and turn off the power switch.
3
4
5
Clean and reinstall the air filters.
The unit uses appr. 2W even when the power switch has been turned
off during the off-season for safety or for saving energy.
Clean both the indoor and outdoor units.
Remove batteries from the remote control.
Ensure that nothing has snapped and that the
earthed flex is not disconnected.
Ensure that the air filters are clean.
Turn on the power switch.
Insert batteries in the remote control.
Installing, inspecting, and replacing the natural enzyme filter and the photocatalytic washable deodorizing filter
•
Installing the natural enzyme filter and the photocatalytic washable deodorizing filter
1. Open the air inlet panel and remove the air filters.
2. Install the filter holders, with the natural enzyme filter and the photocatalytic washable deodorizing filter installed in the holders, in the air-conditioner.
3. Install the air filters and close the air inlet panel.
NOTE
The natural enzyme filter and the photocatalytic washable deodorizing filter may be installed on either the right or left side of the airconditioner.
Filter holder
•
Inspecting and replacing the natural enzyme filter and the photocatalytic washable deodorizing filter
1. Open the air inlet panel and remove the air filters.
2. Remove the filter holders, with the natural enzyme filter and the photocatalytic washable
deodorizing filter installed in the holders, from the air-conditioner.
3. Remove the natural enzyme filter from the filter holder and inspect the filter. Use a vacuum
cleaner to remove any dust or dirt from the natural enzyme filter. Replace the natural enzyme
filter if it cannot be cleaned or if it has been used for about 1 year.
(The natural enzyme filter should be replaced after about 1 year of use. However, the actual
replacement period may vary depending on the conditions in which the filter is used.)
Remove the photocatalytic washable deodorizing filter from the filter holder and inspect the
filter. Periodically, remove any dust or dirt from the photocatalytic washable deodorizing
filter. If the photocatalytic washable deodorizing filter is particularly dirty, it may be washed
with water. However, the filter is fragile so be sure to wash it installed in the filter holder to
avoid damaging it. After washing the filter, place it in sunlight to dry. Placing the filter in
sunlight revitalizes the deodorizing effect.
(Do not dispose of the filter holders. They are reused.)
4. Install the natural enzyme filter and the photocatalytic washable deodorizing filter in the filter
holders, and then install the filter holders in the air-conditioner.
5. Install the air filters and close the air inlet panel.
Filter
Install
For replacement natural enzyme filters and photocatalytic washable deodorizing filters, contact your dealer.
CAUTION
Do not expose natural enzyme filters to direct sunlight for an extended period. The bacteriolytic effect will be lost.
Item
Feature
By using the work of oxygen, mold and bacteria on the filter are
destroyed and the room air is kept clean.
Natural enzyme filter
Photocatalytic washable Sources of odors on the filter are broken up, resulting in a deodeodorizing filter
dorizing effect.
Color
Green
Orange
– 18 –
RKW012A202_En.p65
18
05.2.23, 10:45
Install
Has the unit been installed correctly?
Suitable installation position
• Is there any obstruction in front of the indoor unit, preventing proper ventilation and functioning?
• Don’t install the unit in any of the following places:
• Where there is a danger of leaking inflammable gases.
• Where there is substantial splashing of oil.
• Malfunctioning due to corrosion may occur if the unit is installed in a spa where sulfide gases are generated, or in a seaside resort exposed to
sea breezes. Contact your dealer.
• The air-conditioner and remote control must be at least 1 metre away from a TV set or radio.
• Drain the dehumidified liquid from the indoor unit into a spot that drains well.
Pay attention to operating noises!
•
•
•
•
When you install the unit, take care to choose a place that can comfortably stand the weight of the unit and does not increase the operating noise
or vibration. If there is any likelihood that vibration may be transmitted through the house, fix the unit with the aid of vibration-proof pads
between the unit and the fittings.
Select a place where cold or hot air and operation noises from the indoor and outdoor units do not cause any inconvenience to your neighbours.
Do not leave any obstacles near the outlet and inlet of the outdoor unit. This may cause malfunctioning and increased operating noise.
If you hear an irregular noise during operation, contact your dealer.
Inspection and maintenance
Dependent upon service conditions and operating environment, the inside of the air-conditioner may become dirty after a number of seasons'
service (3 to 5 years). This will reduce performance. In addition to normal cleaning, we would recommend inspection and maintenance. (The airconditioner has a longer life without any trouble.)
• Contact your dealer, or any distributor, for inspection and maintenance. (There will be a charge for this service).
• We would recommend inspection and maintenance to be carried out during the off-season.
• If the supply cord of this appliance is damaged, it must only be replaced by a repair shop appointed by the manufacturer, because special
purpose tools are required.
Troubleshooting
Please carry out the following checks before making a service call.
The air-conditioner does not work at all.
Has the power switch been
turned off?
Has the timer been set in the
"ON" position?
Is there a power failure or a
blown fuse?
If the air-conditioner does not operate properly after you have checked
the left points, or if any doubt still
exists after you have consulted page
20, or if things happen as shown on
page 21, switch off the power and
contact your dealer.
Poor cooling or heating
Have you set the thermostat at a
suitable temperature?
Is the air filter clean? (Not
clogged?)
Did you leave any doors or
windows open?
suitable
temperature
Poor cooling
Is there any direct sunlight entering the room?
Is there a heat source in the
room?
Are there too many people in
the room?
An alternative refrigerant (R410A) is used in this air-conditioner. When asking the
dealer for service or inspection and maintenance, explain the dealer about this matter.
– 19 –
RKW012A202_En.p65
19
05.2.23, 10:45
Please remember!
You cannot restart the unit immediately after you have
stopped it.
Restarting has been blocked for 3 minutes after you have stopped or
after switching off the power during operation, to protect the unit.
(RUN light is on)
Not
operating?
Please wait for
three minutes.
The three-minute protection timer in the microcomputer automatically
starts up again.
Air is not blown out when starting the HEATING operation.
Air flow has stopped to prevent blowing out of cold air until the indoor
heat exchanger has warmed up. (2 to 5 min.) (HOT KEEP)
RUN light blinks slowly
(1.5 sec ON, 0.5 sec OFF)
Air is not blown out for 5 to 10 min. or blown out not warm
wind for a moment at HEATING operation.
RUN light blinks slowly
(1.5 sec ON, 0.5 sec OFF)
When outdoor temperature is low and humidity is high, the unit sometimes performs defrosting automatically. Please wait. During defrosting, water or steam may escape from the outdoor unit.
The indoor fan may stop to prevent re-evaporation of dehumified
moisture and to save energy.
Air is not blown out when starting the DRY operation.
(RUN light is on)
Some steam escapes during COOL operation.
This may occur if the room's temperature and humidity are very high.
It disappears as soon as the temperature and humidity decrease.
There is a slight smell.
Air blown out during operation may smell. This is caused by tobacco
or cosmetics sticking to the unit.
You hear a slight gurgling sound.
This is caused by refrigerating liquid moving within the unit.
You hear a slight cracking sound.
This is caused by heat expansion or contraction.
You hear a hissing or clicking sound.
This is caused by the operation of the refrigerant control valves or
electric components.
After a power cut, you cannot re-start, even if power has been restored, unless you have the power blackout auto restart function.
The memory circuit of the microcomputer has been wiped out. Use the
remote control to start the operation again.
Remote control signals are not received.
Remote control signals may not be received if the signal receiver on
the air-conditioner is exposed to direct sunlight or other bright light.
If so, cut out the sunlight or reduce the other light.
Moisture may form on the air outlet grilles.
If the unit is operated for a long time in high humidity, moisture may
form on the air outlet grilles and start dripping.
– 20 –
RKW012A202_En.p65
20
05.2.23, 10:45
When to contact your distributor without delay
■ Turn off the power switch immediately and inform your dealer in any of the following situations:
The fuse or switch blows continuously.
The cable becomes extremely hot.
The covering of the cable is cracked.
CAUTION
Fuse often blows.
If the power cord becomes damaged, ask your dealer or a qualified engineer to install the
replacement to avoid accidents.
The TV, radio or other equipment
starts to malfunction.
A switch does not activate properly.
When faulty movement is observed when the ON/OFF button is pressed, even after pulling out the power plug and
restarting the operation after 3 minutes, the faulty movement does not disappear.
You hear a strange noise during operation.
The RUN and TIMER lights on the unit indication section
blink quickly (0.5 sec. ON; 0.5 sec. OFF) and don’t work.
3 minutes go
by, but, why ...
Self diagnosis function
■ We are constantly trying to do better service to our customers by installing such judges that show abnormality of each function as follows:
RUN light
Cause
Heat exchanger sensor error
• Broken heat exchanger sensor wire, poor connector
connection
2 time flash
Room temperature sensor error
• Broken room temperature sensor wire, poor connector connection
6 time flash
Indoor fan motor error
• Defective fan motor, poor connector connection
Outdoor temperature sensor error
• Broken outdoor sensor wire, poor connector connection
2 time flash
Outdoor heat exchanger fluid pipe
sensor error
• Broken heat exchanger fluid pipe sensor wire, poor connector
connection
4 time flash
Discharge pipe sensor error
• Broken discharge pipe sensor wire, poor connector connection.
Abnormality of outdoor unit
• Compressor failure, overload operation
5 time flash
Over heat of compressor
• Gas shortage, defective discharge pipe sensor, closed control
valve
6 time flash
Error of signal transmission
• Defective power supply, Broken signal wire, defective in/outdoor
unit boards
1 time flash
TIMER light ON
Description of trouble
TIMER light
1 time flash
RUN light keeps flashing
2 time flash
RUN light ON
– 21 –
RKW012A202_En.p65
21
05.2.23, 10:45
USER’S MANUAL
MITSUBISHI DAIYA
ROOM AIR-CONDITIONER
ENGLISH
MANUEL DE L’UTILISATEUR
FRANÇAIS
CLIMATISEUR D’INTERIEUR
ANWENDERHANDBUCH
DEUTSCH
¨T
BETRIEBSEINHEIT KLIMAGERA
SRK63HE-S
SRK71HE-S
ISTRUZIONI PER L’USO
ITALIANO
CONDIZIONATORE D’ARIA COMPATTO
SRK63CE-S
SRK71CE-S
MANUAL DEL PROPIETARIO
ESPAN˜OL
ACONDICIONADOR AMBIENTAL DE AIRE INCORPORADO
GEBRUIKERSHANDLEIDING
NEDERLANDS
KAMER-AIR-CONDITIONING
MANUAL DO UTILIZADOR
PORTUGUÊS
APARELHO DE AR CONDICIONADO DE INTERIOR
√¢∏°π∂™ Ã∏™∏™
∂§§∏¡π∫∞
∫§πª∞∆π™∆π∫√ ∂™ø∆∂ƒπ∫√À Ãøƒ√À
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
РУССКИЙ
КОМНАТНЫЙ КОНДИЦИОНЕР ВОЗДУХА
KULLANIM KILAVUZU
TÜRKÇE
SPL‹T KL‹MA
AIR-CONDITIONING & REFRIGERATION SYSTEMS HEADQUARTERS
16-5, 2-Chome, Kounan, Minato-ku, Tokyo, 108-8215, Japan
Fax: (03) 6716-5926
MITSUBISHI HEAVY INDUSTRIES EUROPE, LTD.
AIR-CONDITIONER DIVISION
3rd Floor Thavies Inn House 3-4 Holborn Circus London EC1N 2HA, ENGLAND
Phone: 44(0)20 7842 8171
Fax: 44(0)20 7842 8104
RKW012A202_Cover.p65
1
This air conditioner complies with EMC Directive 89/336/EEC, LV
Directive 73/23/EEC.
Este acondicionador de aire cumple con la directiva EMC: 89/
336/EEC, LV Directiva 73/23/EEC.
Ce climatiseur est conforme à la Directive EMC: 89/336/EEC, LV
Directive 73/23/EEC.
Deze airconditioner voldoet aan EMC Directive 89/336/EEC, LV
Directive 73/23/EEC.
Dieses Kimagerät erfüllt die EMC Direktiven 89/336/EEC, LV
Direktiven 73/23/EEC.
Este aparelho de ar condicionado está em conformidade com a
Directiva EMC 88/336/CEE e a Directiva LV 72/23/CEE.
Questo condizionatore d’aria è conforme alla Direttiva EMC: 89/
336/EEC, LV Direttiva 73/23/EEC.
∞˘Ùfi ÙÔ ÎÏÈÌ·ÙÈÛÙÈÎfi Â›Ó·È Û‡ÌʈÓÔ Ì ÙȘ ÚԉȷÁڷʤ˜ Ù˘
√‰ËÁ›·˜ EMC 88/396 Î·È Ù˘ √‰ËÁ›·˜ LV 73/23 Ù˘ ∂√∫.
RKW012A202
05.2.23, 9:31
Download PDF