protech ProX-B501 M2 User`s manual

protech ProX-B501 M2 User`s manual
USER’S
MANUAL
ProX-B501
Pentium® M
Flex-ATX Motherboard
With VGA/Sound/2LAN
Prox-B501 M2
Copyright Notice
Prox-B501 Pentium® M
Flex-ATX Motherboard
With VGA/ Sound/ 2LAN
OPERATION MANUAL
COPYRIGHT NOTICE
This operation manual is meant to assist both Embedded Computer
manufacturers and end users in installing and setting up the system. The
information contained in this document is subject to change without any
notice.
This manual is copyrighted in May, 2004. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical, including
photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
!
Copyright Notice
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void
your authority to operate such equipment.
!
Contents
TABLE OF CONTENTS
CHAPTER
1-1
1-2
1-3
CHAPTER
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
2-12
2-13
2-14
2-15
2-16
2-17
2-18
2-19
2-20
2-21
2-22
2-23
2-24
2-25
2-26
2-27
2-28
2-29
!
!
1
INTRODUCTION
About This Manual ........................................................
System Specification ......................................................
Safety Precautions .........................................................
2
1-2
1-3
1-6
HARDWARE CONFIGURATION
Jumper & Connector Quick Reference Table ................
Component Locations ....................................................
How to Set the Jumpers .................................................
COM Port Connector ……..…………………………...
COM3 RI& Voltage Selection ………………………..
COM4 RI& Voltage Selection …………………………
RS232/422/485(COM2) Selection ...............................
Keyboard or PS/2 Mouse Connector .....................…....
Reset Connector ............................................................
Hard Disk Drive LED Connector ..................................
ATX Power Button …....................................................
External Speaker Connector ..........................................
Power Led Connector ……............................................
KeyLock Connector ..…………………………………
External SMI Connector ………………………………
Inverter Connector …………………………………….
Clear CMOS Data Selection …………………………
CPU Fan Connector …………………………………..
System Fan Connector …………………………………
VGA Connector …………………..……………………
Hard Disk Drive Connector ...........................................
Floppy Disk Drive Connector .......................................
Printer Connector ..........................................................
Universal Serial Bus Connector ………………………
IrDA Connector ……………………………………….
USB & LAN Connector ………………………………
GigaLAN (LAN2) Enable/Disable Selection …………
Memory Installation …………………………………..
LVDS Connector ………………………………………
2-2
2-3
2-4
2-6
2-8
2-9
2-10
2-11
2-11
2-11
2-12
2-12
2-12
2-13
2-13
2-13
2-14
2-14
2-15
2-15
2-16
2-18
2-19
2-20
2-20
2-21
2-23
2-24
2-24
Contents
!
!
2-30
2-31
2-32
2-33
2-34
ATX Power Connector ………………………………..
Sound Connector ……………………………….……..
CD Audio-in Connector ……………………………….
LVDS Panel Voltage Selection ……………………….
LVDS Brightness & Backlight Control Connector ……
CHAPTER
3-1
3-2
3-3
3-4
3-5
3-6
3-7
!
SOFTWARE UTILITIES
Introduction …………..........................................….......
VGA Driver Utility ……………………………….……
Flash BIOS Update ..............................................….......
LAN Driver Utility …...........................................…......
Sound Driver Utility ……………………………………
Intel Chipset Software Installation Utility …..……..…..
USB2.0 Software Installation Utility …………………..
CHAPTER
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
3
4
2-25
2-26
2-27
2-27
2-27
3-2
3-3
3-4
3-6
3-7
3-8
3-9
AWARD BIOS SETUP
Introduction ...................................................................
Entering Setup ...............................................................
The Standard CMOS Features ………............................
The Advanced BIOS Features .......................................
Advanced Chipset Features ...........................................
Integrated Peripherals …...............................................
Power Management Setup .............................................
PNP/PCI Configuration ….............................................
PC Health Status ……....................................................
Frequency Control ....................................…………......
Load Fail-Safe Defaults .................................................
Load Optimized Defaults .........................................….
Password Setting ………………………………………
Save & Exit Setup .........................................................
Exit Without Saving
…………………………………
4-2
4-3
4-4
4-8
4-11
4-13
4-18
4-21
4-23
4-24
4-25
4-25
4-26
4-27
4-28
Contents
!
!
!
APPENDIX
A
EXPANSION BUS
PCI Bus Pin Assignment ..............................................….........
AGP Bus Pin Assignment ..........................………...................
APPENDIX
B
TECHNICAL SUMMARY
Block Diagram ...........................................................................
Interrupt Map ............................................................................
RTC & CMOS RAM Map ........................................................
Timer & DMA Channels Map ..................................................
I/O & Memory Map ...............................................…................
!
A-2
A-3
B-2
B-3
B-4
B-5
B-6
!
!
!
!
!
!
!
!
!
!
CHAPTER
INTRODUCTION!
1
!
This chapter gives you the information for Prox-B501. It also
outlines the System specifications.
Section includes:
z About This Manual
z System Specifications
z Safety Precautions
Experienced users can skip to chapter 2 on page 2-1
for a Quick Start.
!
!
Page:1-1
Chapter
1
Introduction
1-1. ABOUT THIS MANUAL
!
Thank you for purchasing our Prox-B501 Socket 478 Mainboard enhanced
with VGA/Sound/2LAN, which is fully PC / AT compatible. The ProxB501 provides faster processing speed, greater expandability and can
handle more tasks than before. This manual is designed to assist you how
to install and set up the system. It contains four chapters. The user can
apply this manual for configuration according to the following chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specifications for this system. The final page of this chapter will indicate
how to avoid damaging this board.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the
end of this chapter, you will learn how to set jumper and how to configure
this card to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the
VGA utility, LAN utility, Sound utility, and Flash BIOS Update. It also
describes the Watchdog-timer configuration.
Chapter 4 Award BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This Appendix introduces you the expansion bus for AGP BUS and PCI
BUS.
Appendix B Technical Summary
This section gives you the information about the Technical maps.
Appendix C Trouble Shooting
This section outlines the error messages and offers you the methods to
solve the problems.
!
Page: 1-2
Prox-B501 USERcS MANUAL
Chapter
1
Introduction
1-2. SYSTEM SPECIFICATIONS
z CPU (mPGA478):
Intel® Pentium® M / Celeron M Type processor in mPGA478 Socket.
1.3~1.8 GHz clock generator.
Front Side Bus 400 MHZ.
Auto detect voltage regulator.
z MEMORY :
Supports up to 2GB DDR SDRAM.
Two 184-pin DDR DIMM sockets on board.
z CACHE :
Built-in CPU.
z REAL-TIME CLOCK :
256-byte battery backed CMOS RAM.
Hardware implementation to indicate century rollover.
z BIOS :
Phoenix-AwardBIOS• for plug & play function.
4/8MB with VGA BIOS.
Easy update 512KB flash EEPROM.
Support S/IO Setup.
z KEYBOARD CONNECTOR :
Mini DIN connector.
Supports for AT/PS2 keyboard.
z MOUSE CONNECTOR :
Mini DIN connector.
Supports for PS/2 Mouse.
z BUS SUPPORT :
External 2 PCI, 1 AGP Bus
!
Prox-B501 USERcS MANUAL
Page: 1-3
Chapter
1
Introduction
z DISPLAY :
Built-in Intel 855GME/GM, support for CRT, DVO and LVDS.
Onboard 15-pin VGA D-SUB connector, support for resolution on SVGA
Monitor.
z IDE INTERFACE :
Two IDE ports support up to four IED devices.
Supports Ultra DMA 33/66/100.
z FLOPPY DISK DRIVER INTERFACE :
Support up to two Floppy Disk Drives, 3.5" and 5.25" (360K / 720K / 1.2M /
1.44M / 2.88M).
z USB CONNECTOR :
Support up to six USB 2.0 ports.
z LAN ADAPTER :
Dual ports, Intel® 82562EM PHY & Intel 82540EM (10/100/1000)
LAN1: 10BaseT/100 BaseTx Ethernet
LAN2: 10/100/1000 BaseT (82540EM)
Support wake-on-LAN function.
z SERIAL PORT :
Four high speed 16550 Compatible UARTs with Send / Receive 16 Byte
FIFOs; COM1/3/4:RS-232; COM2: RS-232/422/485
MIDI Compatible
Programmable Baud Rate Generator
z SOUND :
Realtek ALC202A (AC’97 Codec).
Fully Compliant AC’97 Analog I/O Component
16-Bit Stereo Full-Duplex Codec
Four Analog Line-level Stereo Inputs for Connection.
High Quality CD Input with Ground Sense
Stereo Line-Level Output
Interface: Line-In, Line-Out, Microphone, and CD Audio-In.
!
Page: 1-4
Prox-B501 USERcS MANUAL
Chapter
1
Introduction
z HARDWARE MONITORING FUNCTION :
Monitor Voltage, CPU temperature, & Cooling fan.
If CPU Temperature is over setting, the buzzer will send out a warming (only
under DOS system).
z IRDA PORT :
5-pin Infrared port, support IrDA v1.0 SIR protocol
z PARALLEL PORT :
SPP / ECP / EPP Function.
1 port, bi-directional parallel port.
z GREEN FUNCTION :
Controlled by hardware and software.
z LED INDICATOR :
System power
Hard Disk access
LAN LED indicator
z DMA CONTROLLER :
82C37 x 2
z DMA CHANNELS :
7
z INTERRUPT CONTROLLERS :
82C59 x 2
z INTERRUPT LEVELS :
15
z OPERATING TEMPERATURE :
0 to 60qC.
z BOARD DIMENSIONS :
228.6mm x 190.5mm, 9” x7.5”
z BOARD NET WEIGHT :
490 gram.
!
Prox-B501 USERcS MANUAL
Page: 1-5
Chapter
1
Introduction
1-3. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Don‘t touch any components of this card when the
card is power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance,
when you connect a jumper or install any cards, a surge of power may
damage the electronic components or the whole system.
!
Page: 1-6
Prox-B501 USERcS MANUAL
HARDWARE
CONFIGURATION
CHAPTER
2
** QUICK START **
Helpful information describes the jumper & connector settings, and
component locations.
Section includes:
z Jumper & Connector Quick Reference Table
z Component Locations
z Configuration and Jumper settings
z Connector’s Pin Assignments
Page 2-1
Chapter
2
Hardware Configuration
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
COM Port Connector
....................…..................………
…………………………………..
COM3 Port RI/Voltage Selection …………………….
COM4 Port RI/Voltage Selection ……………………..
RS232/422/485 (COM2) Selection .....................………
Keyboard/Mouse Connector ..........….....………………
Reset Connector .........................…....................……….
Hard Disk Drive LED Connector .......................……….
ATX Power Button ……………………………………..
External Speaker Connector ....…........................………
Power LED Connector …………….…...............………
KeyLock Connector …………………………………….
External SMI Connector ………………………………..
Inverter Connector ……………………………………..
Clear CMOS Data Selection ……………………………
CPU Fan Connector ……………………………………
System Fan Connector ………………………………….
VGA Connector …................……..……………………
Hard Disk Drive Connector …..............…….........…….
Floppy Disk Drive Connector ….............…….......…….
Printer Connector …........................…...…….........……
Universal Serial Bus Connector …........................…..…
IrDA Connector ………………………………………..
USB&LAN Connector …....................................……
GigaLAN (LAN2) Enable/Disable Selection …………..
ATX Power Connector …………………………………
Memory Installation ..................................…......………
LVDS Connector ………………………………………
Sound Connector ………………………….……………
CD Audio-In Connector ………………………………..
LVDS Voltage Selection ………………………………
LVDS Brightness & Backlight Control Connector ……
Reserved Pin ……………………………………………
Page: 2-2
COM1, COM2
COM3, COM4
JP1
JP3
JP5
JKBMS1
JPANEL (13,15)
JPANEL (9,11)
JPANEL (14,16)
JPANEL (1,3,5,7)
JPANEL (8,10,12)
JPANEL (17,18)
JPANEL (2, 4)
J3
JP12
JCFAN1
JSFAN1
VGA
IDE1, IDE2
FDD1
LPT1
JUSB1
IRDA1, JPANEL (21-24)
J1, J2
JP2
PW1
DIMM1, DIMM2
J4
JAUDIO1
JCDIN1
JP9
J5
J7, JP8,
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
2-2. COMPONENT LOCATIONS
Prox-B501 Connector, Jumper and Component locations
Prox-B501 USERcS MANUAL
Page: 2-3
Chapter
2
Hardware Configuration
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by
using a small plastic "cap", Also known as the jumper cap (with a metal
contact inside), you are able to connect the pins. So you can set-up your
hardware configuration by "open" or "close" pins.
The jumper can be combined into sets that called jumper blocks. When
the jumpers are all in the block, you have to put them together to set up
the hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3),
You can connect PIN1 & PIN2 to create one setting and shorting. You
can either connect PIN2 & PIN3 to create another setting. The same
jumper diagrams are applied all through this manual. The figure below
shows what the manual diagrams look and what they represent.
Page: 2-4
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
JUMPER DIAGRAMS
Jumper Cap
looks like this
2 pin Jumper
looks like this
3 pin Jumper
looks like this
Jumper Block
looks like this
JUMPER SETTINGS
2 pin Jumper close(enabled)
Looks like this
1
1
3 pin Jumper
2-3 pin close(enabled)
Looks like this
1
1
Jumper Block
1-2 pin close(enabled)
Looks like this
1 2
Prox-B501 USERcS MANUAL
1
2
Page: 2-5
Chapter
2
Hardware Configuration
2-4. COM PORT CONNECTOR
COM1 : COM1 Connector
COM1 is fixed as RS-232.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
10
COM1
ASSIGNMENT
DCD
RX
TX
DTR
GND
DSR
RTS
CTS
RI
NC
COM2 : COM2 Connector
The COM2 is selectable as RS-232/422/485.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
10
Page: 2-6
ASSIGNMENT
RS-232
RS-422
DCD
TXRX
TX+
TX
RX+
DTR
RXGND
GND
DSR
RTSRTS
RTS+
CTS
CTS+
RI
CTSNC
NC
RS-485
TXTX+
RX+
RXGND
NC
NC
NC
NC
NC
6
10
1
5
COM2
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
COM3 : COM3 Connector
COM3 is fixed as RS-232.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
DCD
RX
TX
DTR
GND
DSR
RTS
CTS
RI-V
NC
COM4 : COM4 Connector
COM4 is fixed as RS-232.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
DCD
RX
TX
DTR
GND
DSR
RTS
CTS
RI-V
NC
Prox-B501 USERcS MANUAL
5
10
1
6
COM3
5
1
10
6
COM4
Page: 2-7
Chapter
2
Hardware Configuration
2-5. COM3 RI & VOLTAGE SELECTION
JP1 : COM3 RI & Voltage Selection
The selections are as follows:
SELECTION
JUMPER
SETTINGS
RI
1-2
+12V
3-4
+5V
5-6
JUMPER
ILLUSTRATION
***Manufacturing Default – RI.
Page: 2-8
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
2-6. COM4 RI & VOLTAGE SELECTION
JP3 : COM4 RI & Voltage Selection
The selections are as follows:
SELECTION
JUMPER
SETTINGS
RI
1-2
+12V
3-4
+5V
5-6
JUMPER
ILLUSTRATION
***Manufacturing Default – RI.
Prox-B501 USERcS MANUAL
Page: 2-9
Chapter
2
Hardware Configuration
2-7. RS232/422/485 (COM2) SELECTION
JP5 : RS-232/422/485 (COM2) Selection
This connector is used to set the COM2 function.
The jumper settings are as follows :
COM 2
Function
Jumper Settings
(pin closed)
RS-232
Open
RS-422
1-2, 5-6, 7-8
9-10, 11-12, 13-14
15-16, 17-18, 19-20
RS-485
1-3, 4-6, 7-8, 9-10
11-12, 13-14, 15-16
17-18, 19-20
Jumper
Illustrations
*** Manufactory default --- RS-232.
Page: 2-10
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
2-8. KEYBOARD OR PS/2 MOUSE CONNECTOR
JKBMS1 : Keyboard or PS/2 Mouse Connector
DIN connector can support keyboard, Y-cable, or PS/2 Mouse, user
may select the right device to used on “Keyboard or PS/2 Mouse
Selection”. The pin assignments are as follows :
PIN
1
2
3
4
5
6
ASSIGNMENT
Keyboard
PS/2 Mouse
KBDATA
MSDATA
MSDATA
MSDATA
GND
GND
+5V
+5V
KBCLK
MSCLK
MSCLK
MSCLK
6
5
3
4
2 1
9
8 7
JKBMS1
2-9. RESET CONNECTOR
JPAENL (13,15) : Reset Connector.
The pin assignment is as follows :
PIN
13
15
1
JPANEL1
ASSIGNMENT
GND
RST_SW
2-10. HARD DISK DRIVE LED CONNECTOR
JPAENL (9,11) : Hard Disk Drive LED Connector
The pin assignment is as follows :
PIN
9
11
ASSIGNMENT
+5V
HD_LED
Prox-B501 USERcS MANUAL
1
JPANEL1
Page: 2-11
Chapter
2
Hardware Configuration
2-11. ATX POWER BUTTON
JPANEL (14,16) : ATX Power Button
The pin assignment is as follows :
PIN
14
16
1
JPANEL1
ASSIGNMENT
PWR_BN1
PWR_BN2
2-12. EXTERNAL SPEAKER CONNECTOR
JPANEL (1,3,5,7) : External Speaker Connector
The pin assignment is as follows :
SPEAKER
1
PIN
1
3
5
7
JPANEL1
ASSIGNMENT
+5V
NC
NC
SPEAKER SIGNAL
2-13. POWER LED CONNECTOR
JPAENL (8,10,12) : Power LED Connector
The pin assignment is as follows:
PIN
8
10
12
Page: 2-12
ASSIGNMENT
PW_LED
PW_LED
GND
1
JPANEL1
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
2-14. KEYLOCK CONNECTOR
JPAENL (17,18) : Keylock Connector
The pin assignment is as follows:
1
PIN
17
18
JPANEL1
ASSIGNMENT
KEYLOCK
GND
2-15. EXTERNAL SMI CONNECTOR
JPAENL (2,4) : External SMI Connector
The pin assignment is as follows:
PIN
2
4
ASSIGNMENT
5VSB
GND
1
JPANEL1
2-16. INVERTER CONNECTOR
J3 : Inverter Connector
The pin assignment is as follows:
PIN
1
2
3
4
5
ASSIGNMENT
+12V
GND
+5V
GND
ENABKL (Inverter backlight
ON/OFF control signal)
Prox-B501 USERcS MANUAL
Page: 2-13
Chapter
2
Hardware Configuration
2-17. CLEAR CMOS DATA SELECTION
JP12 : Clear CMOS Data Selection
The selections are as follows :
FUNCTION
JUMPER SETTING
(pin closed)
Normal
1-2
Clear CMOS
2-3
JUMPER
ILLUSTRATION
*** Manufacturing Default is set as Normal.
Note: To clear CMOS data, user must power-off the computer and set the jumper
to “Clear CMOS” as illustrated above. After five to six seconds, set the
jumper back to “Normal” and power-on the computer.
2-18. CPU FAN CONNECTOR
JCFAN1 : CPU Fan connector
The pin assignment is as follows:
PIN
1
2
3
Page: 2-14
ASSIGNMENT
GND
+12V
FAN1
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
2-19. SYSTEM FAN CONNECTOR
JSFAN1 : System Fan connector
The pin assignment is as follows:
PIN
1
2
3
ASSIGNMENT
GND
+12V
FAN0
2-20. VGA CONNECTOR
VGA : VGA CRT Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ASSIGNMENT
RED
GREEN
BLUE
NC
GND
GND
GND
GND
VCC
GND
NC
VGA DDA
HSYNC
VSYNC
VGA DDC CLK
Prox-B501 USERcS MANUAL
15
10
11
6
1
5
VGA
Page: 2-15
Chapter
2
Hardware Configuration
2-21. HARD DISK DRIVE CONNECTOR
IDE1: Hard Disk Drive Connector
The Prox-B501 possesses two HDD connectors, IDE1 and IDE2. The
pin assignments are as follows:
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Page: 2-16
ASSIGNMENT
IDERST
PDD7
PDD6
PDD5
PDD4
PDD3
PDD2
PDD1
PDD0
GND
PDREQ
PDIOW#
PDIOR#
PIORDY
PDDACK#
IRQ14
PDA1
PDA0
PDCS#1
IDEACTP#
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
ASSIGNMENT
GND
PDD8
PDD9
PDD10
PDD11
PDD12
PDD13
PDD14
PDD15
NC
GND
GND
GND
PULL LOW
GND
NC
P66 DETECT
PDA2
PDCS#3
GND
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
IDE2: Hard Disk Drive Connector
The pin assignments are as follows:
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
ASSIGNMENT
IDERST
SDD7
SDD6
SDD5
SDD4
SDD3
SDD2
SDD1
SDD0
GND
SDREQ
SDIOW#
SDIOR#
SIORDY
SDDACK#
IRQ15
SDA1
SDA0
SDCS#1
IDEACTS#
Prox-B501 USERcS MANUAL
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
ASSIGNMENT
GND
SDD8
SDD9
SDD10
SDD11
SDD12
SDD13
SDD14
SDD15
NC
GND
GND
GND
PULL LOW
GND
NC
S66 DETECT
SDA2
SDCS#3
GND
Page: 2-17
Chapter
2
Hardware Configuration
2-22. FLOPPY DISK DRIVE CONNECTOR
FDD1 : Floppy Disk Drive Connector
You can use a 34-pin daisy-chain cable to connect two-FDDs. On one
end of this cable is a 34-pin flat cable to attach the FDD on the board,
and the other side is attaches two FDDs.
The pin assignments are as follows :
2
34
1
33
FDD1
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
Page: 2-18
ASSIGNMENT
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
NC
GND
NC
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
ASSIGNMENT
RWC#
NC
DS1#
INDEX
MOA#
DSB#
DSA#
MOB#
DIR#
STEP#
WD#
WE#
TRK0#
WP#
RDATA#
HEAD#
DSKCHG
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
2-23. PRINTER CONNECTOR
LPT : Printer Connector
As to link the Printer to the card, you need a cable to connect both
DB25 connector and parallel port.
The pin assignments are as follows :
LPT1
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
ASSIGNMENT
STB
PDR0
PDR1
PDR2
PDR3
PDR4
PDR5
PDR6
PDR7
ACK#
BUSY
PE
SLCT
Prox-B501 USERcS MANUAL
PIN
14
15
16
17
18
19
20
21
22
23
24
25
26
ASSIGNMENT
AFD#
ERROR#
PAR_INIT#
SLIN#
GND
GND
GND
GND
GND
GND
GND
GND
NC
Page: 2-19
Chapter
2
Hardware Configuration
2-24. UNIVERSAL SERIAL BUS CONNECTOR
JUSB1: Universal Serial Bus Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
+5V
+5V
USB0
USB1
USB0+
USB1+
GND
GND
NC
NC
10
9
2
1
JUSB1
2-25. IRDA CONNECTOR
IRDA1: IrDA (Infrared) Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
Page: 2-20
ASSIGNMENT
+5V
NC
IRRX
GND
IRTX
1
IRDA1
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
JPAENL (21-24) : IrDA Connector
The pin assignment is as follows:
PIN
21
22
23
24
ASSIGNMENT
+5V
GND
IRTX2
IRRX2
1
JPANEL1
2-26. USB&LAN CONNECTOR
J1: USB & LAN Connector
The pin assignments are as follows:
LAN:
PIN
ASSIGNMENT
1
TX+
2
TX3
RX+
4
ISOLATED GND
5
ISOLATED GND
6
RX7
ISOLATED GND
8
ISOLATED GND
11
YLED+
12
YLED13
OLED+
14
OLED The green LED detect power link, and the Yellow
LED is used to detect data active transfer signal.
Prox-B501 USERcS MANUAL
1
10
J1
Page: 2-21
Chapter
2
Hardware Configuration
USB:
PIN
A1
A2
A3
A4
B1
B2
B3
B4
ASSIGNMENT
+5V
USB0USB0+
GND
+5V
USB1USB1+
GND
J2: USB & LAN Connector
The pin assignments are as follows:
LAN:
PIN
ASSIGNMENT
1
TX+
2
TX3
RX+
4
ISOLATED GND
5
ISOLATED GND
6
RX7
ISOLATED GND
8
ISOLATED GND
11
YLED+
12
YLED13
OLED+
14
OLED The green LED detect power link, and the Yellow
LED is used to detect data active transfer signal.
Page: 2-22
1
10
J2
Prox-B501 USERcS MANUAL
Chapter
USB:
PIN
A1
A2
A3
A4
B1
B2
B3
B4
2
Hardware Configuration
ASSIGNMENT
+5V
USB0USB0+
GND
+5V
USB1USB1+
GND
2-27. GIGALAN (LAN2) ENABLE/DISABLE SELECTION
JP2 : GigaLAN (LAN2) Enable/Disable Selection.
The selections are as follows:
FUNCTION
JUMPER SETTING
(pin closed)
Enable
1-2
Disable
2-3
Prox-B501 USERcS MANUAL
JUMPER
ILLUSTRATION
Page: 2-23
Chapter
2
Hardware Configuration
2-28. MEMORY INSTALLATION
Prox-B501 CPU Card can support up to 2GB in two DIMM sockets.
DRAM BANK CONFIGURATION
DIMM 1
128MB
256MB
512MB
1GB
DIMM 2
128MB
256MB
512MB
1GB
TOTAL MEMORY
256MB
512GB
1GB
2GB
2-29. LVDS CONNECTOR
J4 : LVDS Connector.
The pin assignments are as follows:
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
Page: 2-24
ASSIGNMENT
LCD_VCC
ZCM
GND
Z2P
Z1M
Z3P
Z0P
GND
YCM
Y2P
GND
Y1M
Y0P
Y3P
LCD_VCC
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
ASSIGNMENT
GND
ZCP
Z2M
GND
Z1P
Z3M
Z0M
YCP
GND
Y2M
Y1P
GND
Y0M
Y3M
LCD_VCC
J4
1
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
2-30. ATX POWER CONNECTOR
PW1 : ATX Power Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
ASSIGNMENT
3.3V
3.3V
GND
5V
GND
5V
GND
POK
5VSB
12V
3.3V
-12V
GND
PSON
GND
GND
GND
-5V
5V
5V
Prox-B501 USERcS MANUAL
Page: 2-25
Chapter
2
Hardware Configuration
2-31. SOUND CONNECTOR
JAUDIO1 : Sound Connector, including Line-In, Line-Out & Mic.
Also can support only MIC connector. The pin assignments are as
follows :
32
33
34
35
22
23
24
25
2
3
1
4
5
Line-In
PIN ASSIGNMENT
32
LINE_L
33
GND
34
GND
35
LINE_R
Line-In
Line-Out
PIN ASSIGNMENT
22
SPK-L
23
NC
24
NC
25
SPK-R
Mic-In
PIN
1
2
3
4
Page: 2-26
Line-Out
Mic-In
JAUDIO1
ASSIGNMENT
GND
MIC_IN
GND
NC
Prox-B501 USERcS MANUAL
Chapter
2
Hardware Configuration
2-32. CD AUDIO-IN CONNECTOR
1
JCDIN1 : CD Audio-In Connector
The pin assignments are as follows:
PIN
1
2
3
4
JCDIN1
ASSIGNMENT
CD L
GND
GND
CD R
2-33. LVDS PANEL VOLTAGE SELECTION
JP9 : LVDS Panel Voltage Selection.
The selections are as follows:
SELECTION
LVDS_VCC3
LVDS_VCC5
JUMPER SETTING
JUMPER
ILLUSTRATION
1-3
2-4
3-5
4-6
2-34. LVDS BRIGHTNESS & BACKLIGHT CONTROL
CONNECTOR
J5 : LVDS Brightness and Backlight Control Connector
The pin assignment is as follows:
PIN
1
2
ASSIGNMENT
Brightness Control
LCD Back Light Enable
Prox-B501 USERcS MANUAL
1
J5
Page: 2-27
SOFTWARE
UTILITIES
CHAPTER
3
This chapter comprises the detailed information of VGA driver, LAN
driver, and Flash BIOS update. It also describes how to install the
watchdog timer configuration.
Section includes:
z VGA Driver Utility
z Flash BIOS Update
z LAN Driver Utility
z Sound Driver Utility
z Intel® Chipset Software Installation Utility
z USB2.0 Chipset Software Installation Utility
Page: 3-1
Chapter
3
Software Configuration
3-1. INTRODUCTION
Enclosed with our Prox-B501 package is our driver utility, which may comes
in a form of a CD ROM disc or floppy diskettes. For CD ROM disc user,
you will only need some of the files contained in the CD ROM disc, please
kindly refer to the following chart:
Filename
(Assume that CD ROM drive is D:)
D:\VGA
Purpose
Intel 855GME
For VGA driver installation
D:\AWDFLASH
For BIOS update utility
D:\LAN
For LAN Driver installation
D:\SOUND
Realtel ALC202A AC97
For Sound driver installation
D:\UTILITY
Intel® Chipset Software
Installation Utility
For Win 98SE,ME, 2000, XP
D:\USB 2.0
USB 2.0 Software Installation
Utility
For Win 98SE, 2000, ME, XP
User should remember to install the Utility right after the OS fully installed.
Page:3-2
Prox-B501 USERcS MANUAL
Chapter
3
Software Configuration
3-2. VGA DRIVER UTILITY
The VGA interface embedded with our Prox-B501 can support a wide
range of display. You can display CRT, LVDS simultaneously with the
same mode.
1. Win 98/ME program
2. Win NT 4.0 program
3. Win 2000 program
4. Win XP program
5. Linux
3-2-1. Installation of VGA Driver:
To install the VGA Driver, simply follow the following steps:
1.
2.
3.
4.
5.
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 9X/NT4.0/2000/XP system, go to the directory
where VGA driver is located.
Click Setup.exe file for VGA driver installation.
Follow the instructions on the screen to complete the installation.
Once installation is completed, shut down the system and restart in
order for the changes to take effect.
Prox-B501 USERcS MANUAL
Page:3-3
Chapter
3
Software Configuration
3-3. FLASH BIOS UPDATE
3-3-1. System BIOS Update:
Users of Prox-B501 can use the program “Awdflash.exe” contained in
the Utility Disk for system BIOS and VGA BIOS update.
3-3-2. To update VGA BIOS for LCD Flat Panel Display:
As Prox-B501 user, you have to update the VGA BIOS for your specific
LCD flat panel you are going to use. For doing this, you need two files.
One is the “Awdflash.exe” file and the other is the VGA BIOS for ATI
Rage Mobility M6 file for LCD panel display. Both file must be
provided by the vendor or manufacturer. When you get these two files
ready, follow the following steps for updating your VGA BIOS:
1.
2.
3.
4.
Install “Awdflash.exe” from Utility Disk to Drive C.
Insert the VGA BIOS file you have obtained from the vendor.
Type the path to Awdflash.exe and execute the VGA BIOS update
with file H15bxxxx.bin
C:\UTIL\AWDFLASH>AWDFLASH H15bxxxx.bin
The screen will display as the table fount on the next page:
FLASH MEMORY WRITER v7.XX
(C) Award Software 2001 All Rights Reserved
Flash Type – SST 49LF004A /3.3V
File Name to Program: H20bxxxx.bin
Checksum: XXXXX
Error Message:
Page:3-4
Do You Want To Save BIOS (Y/N)
Prox-B501 USERcS MANUAL
Chapter
3
Software Configuration
If you want to save up the original BIOS, enter "Y" and press < Enter >.
If you choose "N", the following table will appear on screen.
FLASH MEMORY WRITER v7.XX
(C) Award Software 2001 All Rights Reserved
Flash Type – SST 49LF004A
/3.3V
File Name to Program: H20bxxxx.bin
Checksum: XXXXX
Error Message :
Are You Sure To Program (Y/N)
Select "Y", and the BIOS will be renewed. When you are refreshing the
BIOS, do not turn off or reset the system, or you will damage the BIOS.
After you have completed all the programming, the screen displays the
table below:
FLASH MEMORY WRITER v7.XX
(C) Award Software 2001 All Rights Reserved
Flash Type – SST 49LF004A
/3.3V
File Name to Program: H20bxxxx.bin
Checksum: XXXXX
Reset System or Power off to
accomplish update process!
F1: Reset
F10: Exit
Please reset or power off the system, and then the Flash BIOS is fully
implemented.
Prox-B501 USERcS MANUAL
Page:3-5
Chapter
3
Software Configuration
3-4. LAN DRIVER UTILITY
3-4-1. Introduction
Prox-B501 is enhanced with LAN function that can support various
network adapters. Installation programs for LAN drivers are listed as
follows:
1. Win 98/ME program
2. Win 2000/XP program
3. Win NT 4.0 program
4. Linux program
5. Netware program
6. Unixware 7.x
For more details on Installation procedure, please refer to Readme.txt
file found on LAN DRIVER UTILITY.
Page:3-6
Prox-B501 USERcS MANUAL
Chapter
3
Software Configuration
3-5. SOUND DRIVER UTILITY
3-5-1. Introduction
The Realtek ALC202A sound function enhanced in this system is fully
compatible with Windows 98, Windows 98SE, Windows NT 4.0,
Windows 2000, Windows ME and Windows XP. Below, you will find
the content of the Sound driver :
1. Win 98/ME program
2. Win NT 4.0 program
3. Win 2000/XP program
4. Linux program
3-5-2. Installation Procedure for Windows 9x/NT/2000/XP
1.
2.
3.
4.
5.
From the task bar, click on Start, and then Run.
In the Run dialog box, type D:\Sound\path\setup, where
“D:\Sound\pathname” refers to the full path to the source files.
Click on the OK button or press the ENTER key.
Click on the “Next” and OK prompts as they appear.
Reboot the system to complete the driver installation.
Prox-B501 USERcS MANUAL
Page:3-7
Chapter
3
Software Configuration
3-6. INTEL® CHIPSET SOFTWARE INSTALLATION UTILITY
3-6-1. Introduction
The Intel® Chipset Software Installation Utility installs to the target
system the Windows* INF files that outline to the operating system how
the chipset components will be configured. This is needed for the
proper functioning of the following features:
-
Core PCI and ISAPNP Services
AGP Support
IDE/ATA33/ATA66/ATA100 Storage Support
USB Support
Identification of Intel® Chipset Components in Device Manager
3-6-2. Installation of Utility for Windows 98SE/ME/2000/XP
The Utility Pack is to be installed only for Windows 98SE, Windows
ME, Windows 2000 and XP program.
It should be installed right after the OS installation, kindly follow the
following steps:
1.
2.
3.
4.
5.
Page:3-8
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 98SE/ME/2000/XP system, go to the directory
where Utility Disc is located.
Click Setup.exe file for utility installation.
Follow the instructions on the screen to complete the installation.
Once installation is completed, shut down the system and restart in
order for the changes to take effect.
Prox-B501 USERcS MANUAL
Chapter
3
Software Configuration
3-7. USB2.0 SOFTWARE INSTALLATION UTILITY
3-7-1. Installation of Utility for Windows 98SE/ 2000/XP
Intel USB 2.0 Enhanced Host Controller driver can only be used on
Windows 98SE, Windows 2000 and Windows XP on Intel Desktop
boards. It should be installed right after the OS installation, kindly
follow the following steps:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 98SE, 2000, and XP system, go to the directory
where Utility Disc is located.
Start the “System” wizard in control panel. (Click
Start/Settings/Control Panel).
Select “Hardware” and click “Device Manager ” button.
Double Click “USB Root Hub”.
Select “Driver”.
Click “Install” to install the driver.
Follow the instructions on the screen to complete the installation.
Click “Finish” after the driver installation is complete.
Prox-B501 USERcS MANUAL
Page:3-9
CHAPTER
AWARD
BIOS SETUP
4
This chapter shows how to set up the Award BIOS.
Section includes:
z Introduction
z Entering Setup
z The Standard CMOS Features
z The Advanced BIOS Features
z The Advanced Chipset Features
z Integrated Peripherals
z Power Management Setup
z PNP/PCI Configuration
z PC Health Status
z Frequency Control
z Load Fail-Safe Defaults
z Load Optimized Defaults
z Password Setting
z Save and Exit Setup
z Exit Without Saving
Page: 4-1
Chapter
4
Award BIOS Setup
4-1. INTRODUCTION
This chapter will show you the function of the BIOS in managing the
features of your system. The Prox-B501 Pentium M Flex-ATX Motherboard
is equipped with the BIOS for system chipset from Award Software Inc.
This page briefly explains the function of the BIOS in managing the special
features of your system. The following pages describe how to use the BIOS
for system chipset Setup menu.
Your application programs (such as word processing, spreadsheets, and
games) rely on an operating system such as DOS or OS/2 to manage such
things as keyboard, monitor, disk drives, and memory.
The operating system relies on the BIOS (Basic Input and Output system), a
program stored on a ROM (Read-only Memory) chip, to initialize and
configure your computer's hardware. As the interface between the hardware
and the operating system, the BIOS enables you to make basic changes to
your system's hardware without having to write a new operating system.
The following diagram illustrates the interlocking relationships between the
system hardware, BIOS, operating system, and application program:
Page: 4-2
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
4-2. ENTERING SETUP
When the system is powered on, the BIOS will enter the Power-On Self
Test (POST) routines and the following message will appear on the lower
screen:
PRESS <DEL> TO ENTER SETUP, ESC TO SKIP MEMORY TEST
As long as this message is present on the screen you may press the <Del>
key (the one that shares the decimal point at the bottom of the number
keypad) to access the Setup program. In a moment, the main menu of the
Award SETUP program will appear on the screen:
Phoenix - AwardBIOS CMOS Setup Utility
ŹStandard CMOS Features
ŹFrequency Control
ŹAdvanced BIOS Features
Load Fail-Safe Defaults
ŹAdvanced Chipset Features
Load Optimized Defaults
ŹIntegrated Peripherals
Set Supervisor Password
ŹPower Management Setup
Set User Password
ŹPnP/PCI Configurations
Save & Exit Setup
ŹPC Health Status
Exit Without Saving
Esc : Quit
F10 : Save & Exit Setup
npom : Select Item
Time, Date, Hard Disk Type .…
Setup program initial screen
You may use the cursor the up/down keys to highlight the individual menu
items. As you highlight each item, a brief description of the highlighted
selection will appear at the bottom of the screen.
Prox-B501 USERcS MANUAL
Page: 4-3
Chapter
4
Award BIOS Setup
4-3. THE STANDARD CMOS FEATURES
Highlight theňSTANDARD CMOS FEATURESʼnand press the <ENTER>
key and the screen will display the following table:
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Time (hh:mm:ss)
Wed, May 26 2004
15 : 5 : 24
IDE Primary Master
IDE Primary Slave
IDE Secondary Master
IDE Secondary Slave
[ None]
[ None]
[ None]
[ None]
Drive A
Drive B
[1.44M, 3.5 in.]
[None]
Video
Halt On
[EGA/VGA]
[All, But Keyboard]
Base Memory
Extended Memory
Total Memory
640K
490496K
491520K
Item Help
Menu Level Ź
‫ٿ‬
‫ٿ‬
‫ٿ‬
‫ٿ‬
npom: Move
Enter: Select
F5: Previous Values
+/-/PU/PD:Value
Change the internal
clock.
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
CMOS Setup screen
In the above Setup Menu, use the arrow keys to highlight the item and then use
the <PgUp> or <PgDn> keys to select the value you want in each item.
Date:
< Month >, < Date > and <Year >. Ranges for each value are in the CMOS
Setup Screen, and the week-day will skip automatically.
Time:
< Hour >, < Minute >, and < Second >. Use 24 hour clock format, i.e., for PM
numbers, add 12 to the hour. For example: 4: 30 P.M. You should enter the
time as 16:30:00.
Page: 4-4
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
IDE Primary Master / Slave:
IDE Secondary Master / Slave:
The BIOS can automatically detect the specifications and optimal operating
mode of almost all IDE hard drives. When you select type AUTO for a hard
drive, the BIOS detect its specifications during POST, every time system
boots.
If you do not want to select drive type AUTO, other methods of selecting
drive type are available:
1.
Match the specifications of your installed IDE hard drive(s) with the
preprogrammed values for hard drive types 1 through 45.
2.
Select USER and enter values into each drive parameter field.
3.
Use the IDE HDD AUTO DETECTION function in Setup.
Here is a brief explanation of drive specifications:
Type: The BIOS contains a table of pre-defined drive types. Each
defined drive type has a specified number of cylinders, number of heads,
write precompensation factor, landing zone, and number of sectors.
Drives whose specifications do not accommodate any predefine type are
classified as type USER.
x
Size: Disk drive capacity (approximate). Note that this size is usually
greater than the size of a formatted disk given by a disk-checking
program.
x
Cyls: number of cylinders.
x
Head: number of heads.
x
Precomp: write precompensation cylinders.
x
Landz: landing zone.
x
Sector: number of sectors.
x
Mode: Auto, Normal, Large or LBA.
Auto: The BIOS automatically determines the optimal mode.
ƒ Normal: Maximum number of cylinders, heads, sectors
supported are 1024, 16 and 63.
ƒ Large: For drives that do not support LBA and have more
than 1024 cylinders.
Prox-B501 USERcS MANUAL
Page: 4-5
Chapter
4
Award BIOS Setup
ƒ LBA (Logical Block Addressing): During drive accesses, the
IDE controller transforms the data address described by
sector, head and cylinder number into a physical block
address, significantly improving data transfer rates. For
drives greater than 1024 cylinders.
DRIVE A AND DRIVE B:
Select the type of floppy disk drive installed in your system. The available
options are 360KB 5.25in, 1.2KB 5.25in, 720KB 3.5in, 1.44MB 3.5in,
2.88MB 3.5in and None.
VIDEO:
This category selects the type of video adapter used for the primary system
monitor. Although secondary monitors are supported, you do not have to
select the type in Setup. Available Options are as follows:
EGA/VGA
Enhanced Graphics Adapter/Video Graphics Array.
For EGA, VGA, SEGA, SVGA or PGA monitor
adapters.
CGA 40
Color Graphics Adapter, power up in 40 column mode.
CGA 80
Color Graphics Adapter, power up in 80 column mode.
MONO
Monochrome adapter, includes high resolution
monochrome adapters.
HALT ON:
This category allows user to choose whether the computer will stop if an error
is detected during power up. Available options are “All errors”, “No errors”,
“All, But keyboard”, “All, But Diskette”, and “All But Disk/Key”.
BASE MEMORY:
Displays the amount of conventional memory detected during boot up.
EXTENDED MEMORY:
Displays the amount of extended memory detected during boot up.
TOTAL MEMORY:
Displays the total memory available in the system.
Page: 4-6
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
HARD DISK ATTRIBUTES:
Type
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
47
Cylinders
306
615
615
940
940
615
642
733
900
820
855
855
306
733
000
612
977
977
1024
733
733
733
306
977
1024
1224
1224
1224
1024
1024
918
925
1024
1024
1024
1024
1024
1024
918
820
1024
1024
809
809
776
Heads
4
4
6
8
6
4
8
5
15
3
5
7
8
7
0
4
5
7
7
5
7
5
4
5
9
7
11
15
8
11
11
9
10
12
13
14
2
16
15
6
5
5
6
6
8
V-P comp
128
300
300
512
512
65535
256
65535
65535
65535
65535
65535
128
65535
0000
0000
300
65535
512
300
300
300
0000
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65335
AUTO
LZone
305
615
615
940
940
615
511
733
901
820
855
855
319
733
000
663
977
977
1023
732
732
733
336
976
1023
1223
1223
1223
1023
1023
1023
926
1023
1023
1023
1023
1023
1023
1023
820
1023
1023
852
852
775
Sect
17
17
17
17
17
17
17
17
17
17
17
17
17
17
00
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
26
17
26
33
Capacity
10
20
30
62
46
20
30
30
112
20
35
49
20
42
00
20
40
56
59
30
42
30
10
40
76
71
111
152
68
93
83
69
85
102
110
119
17
136
114
40
42
65
40
61
100
Award Hard Disk Type Table
Prox-B501 USERcS MANUAL
Page: 4-7
Chapter
4
Award BIOS Setup
4-4. THE ADVANCED BIOS FEATURES
Choose theňADVANCED BIOS FEATURESʼnin the main menu, the screen
shown as below.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
Virus Warning
CPU L1 & L2 Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Boot Up Floppy Seek
Boot Up NumLock Status
Typematic Rate Setting
x Typematic Rate (Chars/Sec)
x Typematic Delay (Msec)
Security Option
OS Select For DRAM > 64MB
npom: Move
Enter: Select
F5: Previous Values
[Disabled]
[Enabled]
[Enabled]
[Floppy]
[HDD-0]
[Enabled]
[On]
[Disabled]
6
250
[Setup]
[Non-OS2]
+/-/PU/PD:Value
Item Help
Menu Level Ź
Allows you to choose
the VIRUS warming
feature for IDE Hard
Disk boot sector
protection. If this
function is enabled and
someone attempt to
write data into this area,
BIOS will show a
warning message on
screen and alarm beep
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
BIOS Features Setup Screen
The “BIOS FEATURES SETUP” allow you to configure your system for
basic operation. The user can select the system’s default speed, boot-up
sequence, keyboard operation, shadowing and security.
A brief introduction of each setting is given below.
VIRUS WARNING :
This item allows you to choose the Virus Warning feature for IDE Hard Disk
boot sector protection. If this function is enabled and someone attempt to
write data into this area, BIOS will show a warning message on screen and
alarm beep.
Page: 4-8
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
CPU L1 & L2 CACHE :
This item allows you to enable L1 & L2 cache.
QUICK POWER ON SELF-TEST:
This item allows you to speed up Power On Self Test (POST) after power-up
the computer. When enabled, the BIOS will shorten or skip some check items
during POST.
FIRST/SECOND/ BOOT DEVICE:
The BIOS attempt to load the operating system from the devices in the
sequence selected in these items.
BOOT UP FLOPPY SEEK:
You may enable / disable this item to define whether the system will look for
a floppy disk drive to boot at power-on, or proceed directly to the hard disk
drive.
BOOT UP NUMLOCK STATUS:
Select power on state for NumLock.
TYPEMATIC RATE SETTING:
Enable this item if you wish to be able to configure the characteristics of
your keyboard. Typematic refers to the way in which characters are entered
repeatedly if a key is held down. For example, if you press and hold down
the "A" key, the letter "a" will repeatedly appear on your screen on your
screen until you release the key. When enabled, the typematic rate and
typematic delay can be selected.
TYPEMATIC RATE (CHARS/SEC):
This item sets the number of times a second to repeat a key stroke when you
hold the key down.
TYPEMATIC DELAY (MSEC):
The item sets the delay time after the key is held down before it begins to
repeat the keystroke.
Prox-B501 USERcS MANUAL
Page: 4-9
Chapter
4
Award BIOS Setup
SECURITY OPTION:
This category allows you to limit access to the system and Setup, or just to
Setup.
System
The system will not boot and access to Setup will be
denied if the correct password is not entered at the
prompt.
Setup
The system will boot, but access to Setup will be
denied if the correct password is not entered at the
prompt.
To disable security, select PASSWORD SETTING at Main Menu and
then you will be asked to enter password. Do not type anything and just
press <Enter>, it will disable security. Once the security is disabled, the
system will boot and you can enter Setup freely.
OS SELECT FOR DRAM >64MB :
Select the operating system that is running with greater than 64MB or RAM
on the system. You may choose OS2 or Non-OS2.
Page: 4-10
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
4-5. ADVANCED CHIPSET FEATURES
Choose theňADVANCED CHIPSET FEATURESʼnfrom the main menu,
the screen shown as below.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Data Integrity Mode
System BIOS Cacheable
Video BIOS Cacheable
Memory Hole At 15M-16M
Delayed Transaction
AGP Aperture Size (MB)
Non-ECC
[Enabled]
[Disabled]
[Disabled]
[Enabled]
[64]
** On-Chip VGA Setting **
On-Chip VGA
On-Chip Frame Buffer Size
Boot Display
Panel Type
[Enabled]
[32MB]
[CRT+LFP]
[640 x480 18bits]
npom: Move
Enter: Select
F5: Previous Values
+/-/PU/PD:Value
Item Help
Menu Level Ź
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Chipset Features Setup Screen
This parameter allows you to configure the system based on the specific
features of the installed chipset. The chipset manages bus speed and
access to system memory resources, such as DRAM and the external cache.
It also coordinates communications between conventional ISA bus and the
PCI bus. It must be stated that these items should never need to be altered.
The default settings have been chosen because they provide the best operating conditions for the system. The only time you might consider making
any changes would be if you discovered that data was being lost while
using your system.
Prox-B501 USERcS MANUAL
Page: 4-11
Chapter
4
Award BIOS Setup
DRAM DATA INTEGRITY MODE:
Select Parity or ECC (error-correcting code), according to the type of installed
DRAM.
SYSTEM BIOS CACHEABLE:
Selecting Enabled allows caching of the system BIOS ROM at F0000hFFFFFh, resulting in better system performance. However, if any program
writes to this memory area, a system error may result.
VIDEO BIOS CACHEABLE:
Select Enabled allows caching of the video BIOS, resulting in better system
performance. However, if any program writes to this memory area, a system
error may result.
MEMORY HOLE AT 15M-16M:
You can reserve this area of system memory for ISA adapter ROM. When
this area is reserved, it cannot be cached. The user information of
peripherals that need to use this area of system memory usually discusses their
memory requirements.
DELAYED TRANSACTION:
The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with PCI
specification version 2.1.
AGP APERTURE SIZE:
This field determines the effective size of the Graphic Aperture used for a
particular GMCH configuration. It can be updated by the GMCH-specific
BIOS configuration sequence before the PCI standard bus enumeration
sequence takes place. If it is not updated then a default value will select an
aperture of maximum size.
Page: 4-12
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
PANEL TYPE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Panel Type
640 x 480
18-bits
…..
[
]
800 x 600
18-bits
…..
[
]
1024 x 768
18-bits
…..
[
]
1280 x 1024
36-bits
…..
[
]
1400 x 1050
36-bits
…..
[
]
1600 x 1200
36-bits
…..
[
]
…..
[
]
1024 x 768
24-bits
np:Move
Prox-B501 USERcS MANUAL
Enter: Accept
ESC:Abort
Page: 4-13
Chapter
4
Award BIOS Setup
4-6. INTEGRATED PERIPHERALS
ChooseňINTEGRATED PERIPHERALSʼnfrom the main setup menu, a
display will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
X OnChip IDE Device
X Onboard Device
XSuperIO Device
Watch Dog Timer Select
Onboard Serial Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
npom: Move
Enter: Select
F5: Previous Values
[Press Enter]
[Press Enter]
[Press Enter]
[Disabled]
[3E8]
[IRQ10]
[2E8]
[IRQ11]
+/-/PU/PD:Value
Item Help
Menu Level
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
Ź
F1:General Help
F7:Optimized Defaults
Integrated Peripherals Setup Screen
By moving the cursor to the desired selection and by pressing the <F1> key,
the all options for the desired selection will be displayed for choice.
If bios setup menu item supports USB device boot, it will cause Win9x detects
the same storages twice when the system is rebooted, and USB HDD will fail.
Note: this cause just happen under Win9x, the phenomenon is a limitation.
Page: 4-14
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
VIA ONCHIP IDE DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
OnChip IDE Device
OnChip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
OnChip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
IDE HDD Block Mode
[Enabled]
npom:Move
Enter: Select
F5: Previous Values
+/-/PU/PD:Value
Item Help
Menu Level Ź
F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. OnChip Primary PCI IDE
The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select Enabled to activate each channel
separately.
2. Primary Master/Slave PIO
Secondary Master/Slave PIO
The four IDE PIO fields allow you to set a PIO mode (0-4) for each of
the four IDE devices that the onboard IDE interface supports. Modes
0 through 4 provide successively increased performance. In Auto
mode, the system automatically determines the best mode for each
device.
3. Primary Master/Slave UDMA
Secondary Master/Slave UDMA
Ultra DMA/33 implementation is possible only if your IDE hard drive
supports it and the operating environment includes a DMA driver
(Windows 95 OSR2 or a third-party IDE bus master driver). If you
Prox-B501 USERcS MANUAL
Page: 4-15
Chapter
4.
4
Award BIOS Setup
hard drive and your system software both support Ultra DMA/33,
select Auto to enable BIOS support.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or
multiple sector read/write. If your IDE hard drive supports block mode
(most new drives do), select Enabled for automatic detection of the
optimal number of block read/writes per sector the drive can support.
ONBOARD DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
Onboard Device
USB Controller
USB 2.0 Support
USB Keyboard Support
USB Mouse Support
AC97 Audio
Onboard LAN
Init Display First
npom:Move
Enter: Select
F5: Previous Values
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Auto]
[Enabled]
[Onboard]
+/-/PU/PD:Value
Item Help
Menu Level Ź
F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. USB Controller
This should be enabled if your system has a USB installed on the
system board and you want to use it. Even when so equipped, if you
add a higher performance controller, you will need to disable this
feature.
2. USB Keyboard Support
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB keyboard.
3. USB Mouse Support
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB Mouse.
Page: 4-16
Prox-B501 USERcS MANUAL
Chapter
4.
5.
4
Award BIOS Setup
AC97 Audio:
This item allows you to enable/disable to support AC97 Audio.
Init Display First
This item allows you to decide to active whether PCI Slot or on-chip
VGA first.
SUPER IO DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
SuperIO Device
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
X RxD, TxD Active
X IR Transmission Delay
X UR2 Duplex Mode
X Use IR Pins
Onboard Parallel Port
Parallel Port Mode
X EPP Mode Select
X ECP Mode Use DMA
PWRON After PWR-Fail
npom:Move
Enter: Select
F5: Previous Values
[Enabled]
[3F8/IRQ4]
[2F8/IRQ3]
[Normal]
Hi, Lo
Enabled
Half
IR-Rx2Tx2
[378/IRQ7]
[SPP]
EPP1.7
3
[Off]
+/-/PU/PD:Value
Item Help
Menu Level Ź
F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. Onboard FDC Controller
Select Enabled if the system has a floppy disk controller (FDC) installed
on the system board and you wish to use it. If you install and-in FDC or
the system has no floppy drive, select Disabled.
2. Onboard Serial Port 1/2
Select an address and corresponding interrupt for the first and second
serial ports.
3. UART Mode Select
This item allows you to select UART mode.
4. RxD, TxD Active
Prox-B501 USERcS MANUAL
Page: 4-17
Chapter
4
Award BIOS Setup
This item allows you to determine the active of RxD, TxD.
IR Transmission Delay
This item allows you to enable/disable IR transmission delay.
6. UR2 Duplex Mode
This item allows you to select the IR half/full duplex function.
7. Use IR Pins
This item allows you to select IR transmission routes, one is RxD2m,
TxD2 (COM Port) and the other is IR-Rx2Tx2
8. Onboard Parallel Port
This item allows you to determine access onboard parallel port
controller with which I/O address.
9. Parallel Port Mode
Select an operating mode for the onboard parallel (printer) port.
Select Normal, Compatible, or SPP unless you are certain your
hardware and software both support one of the other available modes.
10. EPP Mode Select
Select EPP port type 1.7 or 1.9.
11. ECP Mode Use DMA
Select a DMA channel for the parallel port for use during ECP mode.
12. PWRON After PWR-Fail
This item allows you to select if you want to power on the system after
power failure. The choice: Off, On, Former-Sts.
5.
ONBOARD SERIAL PORT 3:
ONBOARD SERIAL PORT 4:
Select a logical COM port name and matching address for the third and
forth serial ports. Select an address and corresponding interrupt for third
and forth serial port.
SERIAL PORT 3 USE IRQ:
SERIAL PORT 4 USE IRQ:
The items set the IRQ address of the serial ports.
Page: 4-18
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
4-7. POWER MANAGEMENT SETUP
ChooseňPOWER MANAGEMENT SETUPʼnoption on the main menu, a
display will be shown on screen as below :
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
[Enabled]
[User Define]
[DPMS]
[Yes]
[3]
[Disabled]
[AT]
Instant-Off
[Enabled]
[Disabled]
0
0:0:0
ACPI Function
Power Management
Video Off Method
Video Off In Suspend
MODEM Use IRQ
Suspend Mode
Power-Supply Type
Soft-Off by PWR-BTTN
Wake-Up by PCI card
Resume by Alarm
x Date (of Month) Alarm
x Time (hh:mm:ss) Alarm
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
npom: Move
Enter: Select
F5: Previous Values
Item Help
Menu Level Ź
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
+/-/PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Power Management Setup Screen
The “Power Management Setup” allows the user to configure the system to
the most effectively save energy while operating in a manner consistent with
your own style of computer use.
ACPI SUSPEND TYPE:
This item allows the user to set the ACPI suspend type to be used.
POWER MANAGEMENT:
This item allows you to select the Power Management mode.
Prox-B501 USERcS MANUAL
Page: 4-19
Chapter
4
Award BIOS Setup
VIDEO OFF OPTION:
When enabled, this feature allows the VGA adapter to operate in a power
saving mode.
Always On
Suspend --> Off
Susp,Stby --> Off
All Modes --> Off
Monitor will remain on during power saving modes.
Monitor blanked when the systems enters the Suspend
mode.
Monitor blanked when the system enters either Suspend or
Standby modes.
Monitor blanked when the system enters any power saving
mode.
VIDEO OFF METHOD:
This determines the manner in which the monitor is blanked.
V/H SYNC+Blank
This selection will cause the system to turn off the vertical
and horizontal synchronization ports and write blanks to the
video buffer.
Blank Screen
DPMS
This option only writes blanks to the video buffer.
Select this option if your monitor supports the Display
Power Management Signalling (DPMS) standard of the
Video Electronics Standards to select video power
management values.
MODEM USE IRQ:
This item enable you to name the interrupt request (IRQ) line assigned to
the modem (if any) on your system. Activity of the selected IRQ always
awakens the system.
SUSPEND MODE:
When enabled and after the set time of system inactivity, all devices except
the CPU will be shut off.
SOFT-OFF BY PWR-BTTN:
Pressing the power button for more than 4 seconds forces the system to
enter the Soft-Off state when the system has “hung”. The choices are
Delay 4 Sec and Instant-Off.
WAKE-UP BY PCI CARD:
An input signal from PME on the PCI card awakens the system from a soft
off state.
Page: 4-20
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
RESUME BY ALARM:
When Enabled, your can set the date and time at which the RTC (real-time
clock) alarm awakens the system from Suspend mode.
PM EVENTS:
PM events are I/O events whose occurrence can prevent the system from
entering a power saving mode or can awaken the system from such a mode.
In effect, the system remains alert for anything, which occurs to a device
which is configured as Enabled, even when the system is in a power down
mode. (1) Primary IDE 0 (2) Primary IDE 1 (3) Secondary IDE 0 (4)
Secondary IDE 1 (5) FDD, COM, LPT Port
Prox-B501 USERcS MANUAL
Page: 4-21
Chapter
4
Award BIOS Setup
4-8. PNP/PCI CONFIGURATION
Choose ňPNP/PCI CONFIGURATIONʼn from the main menu, a display
will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
Reset Configuration Data
Resources Controlled By
x IRQ Resources
PCI/VGA Palette Snoop
npom: Move
Enter: Select
F5: Previous Values
[Disabled]
Item Help
Menu Level Ź
[Auto (ESCD)]
Press Enter
Select Yes if you are
using a Plug and Play
capable operating
system Select No if
you need the BIOS to
configure non-boot
devices
[Disabled]
+/-/PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
PNP/PCI Configuration Setup Screen
The PNP/PCI Configuration Setup describes how to configure PCI bus system.
PCI, also known as Personal Computer Interconnect, is a system, which
allows I/O devices to operate at speeds nearing the speed of the CPU itself
uses when communicating with its own special components.
This section covers technical items, which is strongly recommended for
experienced users only.
RESET CONFIGURATION DATA:
Normally, you leave this field Disabled. Select Enabled to reset Extended
System Configuration Data (ESCD) when you exit Setup if you have
installed a new add-on and the system configuration has caused such a
serious conflict that the operating system cannot boot.
Page: 4-22
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
RESOURCE CONTROLLED BY:
The Award Plug and Play Bios can automatically configure all of the booth
and Plug and Play-compatible devices. However, this capability means
absolutely nothing unless you are using a Plug and Play operating system
such as Windows 95. By choosing “manual”, you are allowed to
configure the IRQ Resources and DMA Resources.
IRQ RESOURCES:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
IRQ Resources
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-12 assigned to
IRQ-14 assigned to
IRQ-15 assigned to
npom:Move
Enter: Select
F5: Previous Values
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
+/-/PU/PD:Value
Item Help
Menu Level Ź
Legacy ISA for devices
compliant with the
original PC AT bus
specification, PCI/ISA
PnP for devices
compliant with the Plug
and Play standard
whether designed for
PCI or ISA bus
architecture
F10:Save
F6:Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Descriptions on each item above are as follows:
13. IRQ-n Assigned to:
You may assign each system interrupt a type, depending on the type of
device using the interrupt.
Prox-B501 USERcS MANUAL
Page: 4-23
Chapter
4
Award BIOS Setup
4-9. PC HEALTH STATUS
Choose ňPC HEALTH STATUSʼn from the main menu, a display will
be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
Current Warning Temperature
Current CPU Temperature
Current SYSTEM Fan Speed
Current CPU Fan Speed
Vcore
Vccp
3.3 V
+5V
+12 V
-12 V
-5V
VBAT (V)
5VSB (V)
Shutdown Temperature
npom: Move
Enter: Select
F5: Previous Values
[Disabled]
45ƨ/113Ʃ
0 RPM
5113 RPM
1.34V
1.02V
3.36V
5.05V
12.03V
-12.52V
- 5.04V
3.20V
4.96V
[Disabled]
+/-/PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
Item Help
Menu Level Ź
ESC:Exit
F1:General Help
F7:Optimized Defaults
PC Health Status Setup Screen
The PC Health Status Setup allows you to select whether to choose between
monitoring or to ignore the hardware monitoring function of your system.
CURRENT WARNING TEMPERATURE:
Select the combination of lower and upper limits for the CPU temperature.
If the CPU temperature extends beyond either limit, any warning
mechanism programmed into your system will be activated.
CURRENT CPU TEMPERATURE:
This item shows you the current CPU temperature.
CURRENT SYSTEM FAN SPEED:
This item shows you the current System FAN speed.
Page: 4-24
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
CURRENT CPU FAN SPEED:
This item shows you the current CPUFAN speed.
VCORE:
This item shows you the current system voltage.
3.3V / +5V / +12V / -12V / -5V / 5VSB:
Show you the voltage of 3.3V/+5V/+12V/-12V/-5V/5VSB.
SHUTDOWN TEMPERATURE:
This item allows you to set up the CPU shutdown Temperature.
function is only effective under Windows 98 ACPI mode.
This
4-10. FREQUENCY CONTROL
Choose ňFREQUENCY CONTROLʼn from the main menu, a display
will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
Frequency Control
Auto Detect PCI Clk
Spread Spectrum
[Enabled]
[Enabled]
Item Help
Menu Level Ź
npom: Move
Enter: Select
F5: Previous Values
+/-/PU/PD:Value
F10:Save
F6: Fail-Safe Defaults
ESC:Exit
F1:General Help
F7:Optimized Defaults
Frequency Control Setup Screen
This setup menu allows you to specify your settings for frequency control.
Prox-B501 USERcS MANUAL
Page: 4-25
Chapter
4
Award BIOS Setup
AUTO DETECT PCI CLK:
This item allows you to enable or disable auto detect PCI Clock.
SPREAD SPECTRUM:
When the system clock generator pulses, the extreme values of the pulse
generate excess EMI. Enabling pulse spectrum spread modulation
changes the extreme values from spikes to flat curves, thus reducing EMI.
This benefit may in some cases be outweighed by problems with timingcritical devices such as a clock-sensitive SCSI device.
4-11. LOAD FAIL-SAFE DEFAULTS
By pressing the <ENTER> key on this item, you get a confirmation dialog
box with a message similar to the following:
Load Fail-Safe Defaults ( Y/N ) ? N
To use the BIOS default values, change the prompt to "Y" and press the
<Enter > key. CMOS is loaded automatically when you power up the
system.
4-12. LOAD OPTIMIZED DEFAULTS
When you press <Enter> on this category, you get a confirmation dialog
box with a message similar to the following:
Load Optimized Defaults ( Y/N ) ? N
Pressing "Y" loads the default values that are factory setting for optimal
performance system operations.
Page: 4-26
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
4-13. PASSWORD SETTING
User is allowed to set either supervisor or user password, or both of them.
The difference is that the supervisor password can enter and change the
options of the setup menus while the user password can enter only but do not
have the authority to change the options of the setup menus.
TO SET A PASSWORD
When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.
Enter Password:
Type the password up to eight characters in length, and press < Enter >.
The password typed now will clear any previously entered password from
CMOS memory. You will be asked to confirm the password. Type the
password again and press the < Enter > key. You may also press < Esc >
to abort the selection and not enter a password.
User should bear in mind that when a password is set, you will be
asked to enter the password everything you enter CMOS setup Menu.
TO DISABLE THE PASSWORD
To disable the password, select this function (do not enter any key when
you are prompt to enter a password), and press the <Enter> key and a
message will appear at the center of the screen:
PASSWORD DISABLED!!!
Press any key to continue...
Press the < Enter > key again and the password will be disabled.
password is disabled, you can enter Setup freely.
Prox-B501 USERcS MANUAL
Once the
Page: 4-27
Chapter
4
Award BIOS Setup
4-14. SAVE & EXIT SETUP
After you have completed adjusting all the settings as required, you must
remember to save these setting into the CMOS RAM. To save the settings,
select “SAVE & EXIT SETUP” and press <Enter>, a display will be shown
as follows:
Phoenix - AwardBIOS CMOS Setup Utility
ŹStandard CMOS Features
ŹFrequency Control
ŹAdvanced BIOS Features
Load Fail-Safe Defaults
ŹAdvanced Chipset Features
Load Optimized Defaults
ŹIntegrated Peripherals
Set Supervisor Password
word
ŹPower Management
ŹPnP/PCI Configura
Save to CMOS and EXIT Y/N)? Y
Saving
ŹPC Health Status
Esc : Quit
F10 : Save & Exit Setup
etup
npom : Select Item
Save Data to CMOS
When you confirm that you wish to save the settings, your system will be
automatically restarted and the changes you have made will be implemented.
You may always call up the setup program at any time to adjust any of the
individual items by pressing the <Del> key during boot up.
Page: 4-28
Prox-B501 USERcS MANUAL
Chapter
4
Award BIOS Setup
4-15. EXIT WITHOUT SAVING
If you wish to cancel any changes you have made, you may select the
“EXIT WITHOUT SAVING” and the original setting stored in the CMOS
will be retained. The screen will be shown as below:
Phoenix - AwardBIOS CMOS Setup Utility
ŹStandard CMOS Features
ŹFrequency Control
ŹAdvanced BIOS Features
Load Fail-Safe Defaults
ŹAdvanced Chipset Features
Load Optimized Defaults
ŹIntegrated Peripherals
Set Supervisor Password
word
ŹPower Management
ŹPnP/PCI Configura
Quit Without Saving (Y/N)? N
Saving
ŹPC Health Status
Esc : Quit
F10 : Save & Exit Setup
etup
npom : Select Item
Abandon all Datas
Prox-B501 USERcS MANUAL
Page: 4-29
APPENDIX
EXPANSION BUS
A
This appendix indicates the pin assignments.
Section includes:
z PCI BUS Pin Assignment
z AGP BUS Pin Assignment
Page: A-1
Appendix
A
Expansion Bus
PCI BUS PIN ASSIGNMENT
Like ISA-BUS connector, the PCI-BUS edge connector is also divided into two
sets: one consists of 98-pin; the other consists of 22-pin.
The pin assignments are as follows :
B1
B49 B52
B62
A1
A49 A52
A62
B
A
B
A
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
-12V
TCK
GND
TDO
+5V
+5V
INTB#
INTD#
REQ3#
REQ1#
GNT3#
GND
GND
CLKA
GND
CLKB
GND
REQ0#
+5V(I/O)
AD31
AD29
GND
AD27
AD25
+3.3V
C/BE3#
AD23
GND
AD21
AD19
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
TRST#
+12V
TMS
TDI
+5V
INTA#
INTC#
+5V
CLKC
+5V(I/O)
CLKD
GND
GND
GNT1#
RST#
+5V(I/O)
GNT0#
GND
REQ2#
AD30
+3.3V
AD28
AD26
GND
AD24
GNT2#
+3.3V
AD22
AD20
GND
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
+3.3V
AD17
C/BE2#
GND
IRDY#
+3.3V
DEVSEL#
GND
LOCK#
PERR#
+3.3V
SERR#
+3.3V
C/BE1#
AD14
GND
AD12
AD10
GND
AD08
AD07
+3.3V
AD05
AD03
GND
AD01
+5V(I/O)
ACK64#
+5V
+5V
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
AD18
AD16
+3.3V
FRAME#
GND
TRDY#
GND
STOP#
+3.3V
SDONE
SB0#
GND
PAR
AD15
+3.3V
AD13
AD11
GND
AD09
C/BE0#
+3.3V
AD06
AD04
GND
AD02
AD00
+5V(I/O)
REQ64#
+5V
+5V
Page: A-2
Prox-B501USERcS MANUAL
Appendix
A
Expansion Bus
AGP BUS PIN ASSIGNMENT
AGP Connector
(Note: only for AGP 4X/1.5V)
The pin assignments are as follows :
PIN
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
ASSIGNMENT
+12V
TYPEDET
RESERVED
USBGND
INTA
RST
GNT
VCC3.3
ST1
RESERVED
PIPE
GND
WBF
SBA1
VCC3.3
SBA3
SB_STB
GND
SBA5
SBA7
RESERVED
GND
RESERVED
VCC3.3
AD30
AD28
VCC3.3
AD26
AD24
GND
AD_STB1
C/BE3
Prox-B501 USERcS MANUAL
PIN
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
A51
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
A63
A64
A65
A66
ASSIGNMENT
VDDQ
AD22
AD20
GND
AD18
AD16
VDDQ
FRAME
RESERVED
GND
RESERVED
VCC3.3
TRDY
STOP
PME
GND
PAR
AD15
VDDQ
AD13
AD11
GND
AD9
C/BE0
VDDQ
AD_STB0
AD6
GND
AD4
AD2
VDDQ
AD0
RESERVED
Page: A-3
Appendix
A
PIN
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
B31
B32
B33
Page: A-4
Expansion Bus
ASSIGNMENT
OVRCNT
+5V
+5V
USB+
GND
INTB
CLK
REQ
VCC3.3
ST0
ST2
RBF
GND
RESERVED
SBA0
VCC3.3
SBA2
SB_STB
GND
SBA4
SBA6
RESERVED
GND
RESERVED
VCC3.3
AD31
AD29
VCC3.3
AD27
AD25
GND
AD_STB1
AD23
PIN
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B50
B51
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
B63
B64
B65
B66
ASSIGNMENT
VDDQ
AD21
AD19
GND
AD17
C/BE
VDDQ
IRDY
RESERVED
GND
RESERVED
VCC3.3
DEVEL
VDDQ
PERR
GND
SERR
C/BE1
VDDQ
AD14
AD12
GND
AD10
AD8
VDDQ
AD_STB0
AD7
GND
AD5
AD3
VDDQ
AD1
RESERVED
Prox-B501USERcS MANUAL
TECHNICAL
SUMMARY
APPENDIX
B
This section introduce you the maps concisely.
Section includes:
z Block Diagram
z Interrupt Map
z RTC & CMOS RAM Map
z Timer & DMA Channels Map
z I / O & Memory Map
Page: B-1
Appendix
B
Technical Summary
BLOCK DIAGRAM
Page: B-2
Prox-B501 USERcS MANUAL
Appendix
B
Technical Summary
INTERRUPT MAP
IRQ
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ASSIGNMENT
System TIMER
Keyboard
Cascade
Serial port 2
Serial port 1
Available
Floppy
Parallel port 1
RTC clock
Available
Available
Available
PS/2 Mouse
Math coprocessor
IDE1
IDE2
Prox-B501 USERcS MANUAL
Page: B-3
Appendix
B
Technical Summary
RTC & CMOS RAM MAP
CODE
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
30
31
32
33
34-3F
40-7f
Page: B-4
ASSIGNMENT
Seconds
Second alarm
Minutes
Minutes alarm
Hours
Hours alarm
Day of week
Day of month
Month
Year
Status register A
Status register B
Status register C
Status register D
Diagnostic status byte
Shutdown byte
Floppy Disk drive type byte
Reserve
Hard Disk type byte
Reserve
Equipment byte
Base memory low byte
Base memory high byte
Extension memory low byte
Extension memory high byte
Reserved for extension memory low byte
Reserved for extension memory high byte
Date Century byte
Information Flag
Reserve
Reserved for Chipset Setting Data
Prox-B501 USERcS MANUAL
Appendix
B
Technical Summary
TIMER & DMA CHANNELS MAP
Timer Channel Map :
Timer Channel
0
1
2
Assignment
System timer interrupt
DRAM Refresh request
Speaker tone generator
DMA Channel Map :
DMA Channel
0
1
2
3
4
5
6
7
Assignment
Available
Available
Floppy
Available
Cascade
Available
Available
Available
Prox-B501 USERcS MANUAL
Page: B-5
Appendix
B
Technical Summary
I/O & MEMORY MAP
Memory Map :
MEMORY MAP
0000000-009FFFF
00A0000-00BFFFF
00C0000-00DFFFF
00E0000-00EFFFF
00F0000-00FFFFF
0100000-FFFFFFF
ASSIGNMENT
System memory used by DOS and
application
Display buffer memory for VGA/ EGA /
CGA / MONOCHROME adapter
Reserved for I/O device BIOS ROM or
RAM buffer.
Reserved for PCI device ROM
System BIOS ROM
System extension memory
I/O Map :
I/O MAP
000-01F
020-021
022-023
040-05F
060-06F
070-07F
080-09F
0A0-0BF
0C0-0DF
0F0-0FF
1F0-1F8
278-27F
2B0-2DF
2F8-2FF
360-36F
378-37F
3B0-3BF
3C0-3CF
3D0-3DF
3F0-3F7
3F8-3FF
Page: B-6
ASSIGNMENT
DMA controller (Master)
Interrupt controller (Master)
Chipset controller registers I/O ports.
Timer control regsiters.
Keyboard interface controller (8042)
RTC ports & CMOS I/O ports
DMA register
Interrupt controller (Slave)
DMA controller (Slave)
Math coprocessor
Hard Disk controller
Parallel port-2
Graphics adapter controller
Serial port-2
Net work ports
Parallel port-1
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy disk controller
Serial port-1
Prox-B501 USERcS MANUAL
TROUBLE
SHOOTING
APPENDIX
C
This section outlines the errors may occur when you operate the
system. It also gives you the suggestions on solving the problems.
Section includes:
z Trouble Shooting for Error Messages
z Trouble Shooting for POST Code
Page: C-1
Appendix
C
Trouble Shooting
TROUBLE SHOOTING FOR ERROR MESSAGES
The following information gives you the error messages and the troubleshooting. Please adjust your systems according to the messages below. And
make sure all the components and connectors are in proper position and
firmly attached. If the errors still encountered, please contact with your
distributor for maintenance.
POST BEEP :
Currently there are two kinds of beep codes in BIOS. One code indicates
that a video error has occurred and the BIOS cannot initialize the video
screen to display any additional information. This beep code consists of a
single long beep followed by two short beeps. The other code indicates that
your DRAM error has occurred. This beep code consists of a single long
beep repeatedly.
CMOS BATTERY HAS FAILED :
This message informs you that the CMOS battery is no longer functional.
The user should replace it.
CMOS CHECKSUM ERROR :
This message informs you that the CMOS is incorrect. This error may
have caused by a weak battery. Check the battery and replace if necessary.
DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER :
No boot device was found. This could mean that either a boot drive was
not detected or the drive does not contain proper system boot files. Insert a
system disk into Drive A: and press < Enter >. If you assumed the system
would boot from the hard drive, make sure the controller is inserted
correctly and all cables are properly attached. Also make sure the disk is
formatted as a boot device. Then reboot the system.
DISKETTE DRIVES OR TYPES MISMATCH ERROR - RUN SETUP :
Type of diskette drive installed in the system is different from the CMOS
definition. Run Setup to reconfigure the drive type correctly.
Page: C-2
Prox-B501 USERcS MANUAL
Appendix
C
Trouble Shooting
DISPLAY SWITCH IS SET INCORRECTLY :
Display switch on the motherboard can be set to either monochrome or
color. This indicates the switch is set to a different setting than indicated in
Setup. Determine which setting is correct, and then either turn off the
system and change the jumper, or enter Setup and change the VIDEO
selection.
DISPLAY TYPE HAS CHANGED SINCE LAST BOOT :
Since last powering off the system, the display adapter has been changed.
You must configure the system for the new display type.
EISA CONFIGURATION CHECKSUM ERROR
PLEASE RUN EISA CONFIGURATION UTILITY :
The EISA non-violatile RAM checksum is incorrect or cannot correctly
read the EISA slot. This can indicate either the EISA non-volatile
memory has become corrupt or the slot has been configured incorrectly.
Also be sure the card is installed firmly in the slot.
EISA CONFIGURATION IS NOT COMPLETE
PLEASE RUN EISA CONFIGURATION UTILITY :
The slot configure information stored in the EISA non-volatile memory is
incomplete.
Note: When either of these errors appear, the system will boot in ISA mode,
which allows you to run the EISA Configuration Utility.
ERROR ENCOUNTERED INITIALIZING HARD DRIVE :
Hard drive cannot be initialized. Be sure the adapter is installed correctly
and all cables are correctly and firmly attached. Also be sure the correct
hard drive type is selected in Setup.
ERROR INITIALIZING HARD DISK CONTROLLER :
Cannot initialize controller. Make sure the cord is correctly and firmly
installed in the bus. Be sure the correct hard drive is selected in Setup. Also
check to see if any jumper needs to be set correctly on the hard drive.
Prox-B501 USERcS MANUAL
Page: C-3
Appendix
C
Trouble Shooting
FLOPPY DISK CNTRLR ERROR OR NO CNTRLR PRESENT :
Cannot find or initialize the floppy drive controller. Make sure the
controller is installed correctly and firmly. If there are no floppy drives
installed, be sure the Diskette Drive selection in Setup is set to NONE.
INVALID EISA CONFIGURATION
PLEASE RUN EISA CONFIGURATION UTILITY :
The non-volatile memory containing EISA configuration information was
programmed incorrectly or has become corrupt. Re-run EISA configuration
utility to correctly program the memory.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
KEYBOARD ERROR OR NO KEYBOARD PRESENT :
Cannot initialize the keyboard. Make sure that the keyboard is properly
attached and no keys being pressed during the boot.
If you are purposely configuring the system without a keyboard, set the
error halt condition in Setup to HALT ON ALL, BUT KEYBOARD. This
will cause the BIOS to ignore the missing keyboard and continue the boot.
MEMORY ADDRESS ERROR AT ... :
Indicates a memory address error at a specific location. You can use this
location along with the memory map for your system to find and replace the
bad memory chips.
MEMORY PARITY ERROR AT ... :
Indicates a memory parity error at a specific location. You can use this
location along with the memory map for your system to find and replace the
bad memory chips.
MEMORY SIZE HAS CHANGED SINCE LAST BOOT :
Memory has been added or removed since the last boot. In EISA mode use
Configuration Utility to reconfigure the memory configuration. In ISA
mode enter Setup and enter the new memory size in the memory fields.
Page: C-4
Prox-B501 USERcS MANUAL
Appendix
C
Trouble Shooting
MEMORY VERIFY ERROR AT ... :
Indicates an error verifying a value already written to memory. Use the
location along with your system's memory map to locate the bad chip.
OFFENDING ADDRESS NOT FOUND :
This message is used in conjunction with the I/O CHANNEL CHECK and
RAM PARITY ERROR messages when the segment that has caused the
problem cannot be isolated.
OFFENDING SEGMENT :
This message is used in conjunction with the I/O CHANNEL CHECK and
RAM PARITY ERROR messages when the segment that has caused the
problem has been isolated.
PRESS A KEY TO REBOOT :
This will be displayed at the bottom screen when an error occurs that
requires you to reboot. Press any key and the system will reboot.
PRESS F1 TO DISABLE NMI, F2 TO REBOOT :
When BIOS detects a Non-maskable Interrupt condition during boot, this
will allow you to disable the NMI and continue to boot, or you can reboot
the system with the NMI enabled.
RAM PARITY ERROR – CHECKING FOR SEGMENT :
Indicates a parity error in Random Access Memory.
Should be Empty But EISA Board Found
PLEASE RUN EISA CONFIGURATION UTILITY :
A valid board ID was found in a slot that was configured as having no
board ID.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
Should Have EISA Board But Not Found
PLEASE RUN EISA CONFIGURATION UTILITY :
The board installed is not responding to the ID request, or no board ID has
been found in the indicated slot.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
Prox-B501 USERcS MANUAL
Page: C-5
Appendix
C
Trouble Shooting
Slot Not Empty :
Indicates that a slot designated as empty by the EISA Configuration Utility
actually contains a board.
SYSTEM HALTED, (CTRL-ALT-DEL) TO REBOOT :
Indicates the present boot attempt has been aborted and the system must be
rebooted. Press and hold down the CTRL and ALT keys and press DEL.
Wrong Board in Slot
PLEASE RUN EISA CONFIGURATION UTILITY :
The board ID does not match the ID stored in the EISA non-volatile
memory.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.
FLOPPY DISK(S) FAIL (80) :
Unable to reset floppy subsystem.
FLOPPY DISK(S) FAIL (40) :
Floppy type dismatch.
Hard Disk(S) Fail (80) :
Hard Disk Drive reset failed.
Hard Disk(S) Fail (40) :
Hard Disk Drive controller diagnostics failed.
Hard Disk(S) Fail (20) :
Hard Disk Drive initialization error.
Hard Disk(S) Fail (10) :
Unable to recalibrate fixed disk.
Hard Disk(S) Fail (08) :
Sector Verify failed.
Keyboard is locked out – Unlock the key :
BIOS detect the keyboard is locked. P17 of keyboard controller is pulled
low.
Page: C-6
Prox-B501 USERcS MANUAL
Appendix
C
Trouble Shooting
Keyboard error or no keyboard present :
Cannot initialize the keyboard. Make sure the keyboard is attached
correctly and no keys are being pressed during the boot.
Manufacturing POST loop :
System will repeat POST procedure infinitely while the P15 of keyboard
controller is pull low. This is also used for M/B burn in test.
BIOS ROM checksum error – System halted :
The checksum of ROM address F0000H-FFFFFH is bad.
Memory test fail :
BIOS reports the memory test fail if the onboard memory is tested error.
Prox-B501 USERcS MANUAL
Page: C-7
Appendix
C
Trouble Shooting
TROUBLE SHOOTING FOR POST CODES
The lists below indicate you the post codes. Please follow the instruction to
adjust your system. If the error still occurred, please contact with your
distributor for maintenance.
CFh
:
Test CMOS R/W functionality.
C0h
:
Early chipset initialization
- Disable shadow RAM
- Disable L2 cache (socket 7 or below)
- Program basic chipset registers
C1h
:
Detect memory
- Auto-detection of DRAM size, type and ECC
- Auto-detection of L2 cache (socket 7 or below)
C3h
:
Expand compressed BIOS code to DRAM.
C5h
:
Call chipset hook to copy BIOS black to E000 & F000 shadow
RAM.
0h1
:
Expand the Xgroup codes locating in physical address 1000:0
02h
:
Reserved.
03h
:
Initial Superio_Early_Init switch.
04h
:
Reserved.
05h
:
1. Blank out screen
2. Clear CMOS error flag
06h
:
Reserved
07h
:
1. Clear 8042 interface
2. Initialize 8042 self-test
Page: C-8
Prox-B501 USERcS MANUAL
Appendix
C
Trouble Shooting
08h
:
1. Test special keyboard controller for Winbond 977 series Super
I/O Chips.
2. Enable keyboard interface.
09h
:
Reserved
0Ah :
1. Disable PS/2 mouse interface (optional)
2. Auto detect ports for keyboard & mouse followed by a port &
interface swap (optional).
3. Reset keyboard for Winbond 977 series Super I/O chips.
0Bh :
Reserved
0Ch :
Reserved
0Dh :
Reserved
0Eh :
Test F000h segment shadow to see whether it is R/W-able or not.
If test fails, keep beeping the speaker.
0Fh :
Reserved
10h :
Auto detect flash type to load appropriate flash R/W codes into the
run time area in F000 for ESCD and DMI support.
11h :
Reserved
12h :
Use walking 1’s algorithm to check out interface in CMOS
circuitry. Also set real-time clock power status, and then check
for override.
13h :
Reserved
14h :
Program chipset default values into chipset. Chipset default
values are MODBINable by OEM customers.
15h :
Reserved
16h :
Initial Early_Init_Onboard_Generator switch.
Prox-B501 USERcS MANUAL
Page: C-9
Appendix
C
Trouble Shooting
17h
:
Reserved
18h
:
Detect CPU information including brand, SMI type (Cyrix or Intel)
and CPU level (586 or 686).
19h
:
Reserved
1Ah :
Reserved
1Bh :
Initial interrupts vector table. If no special specified, all H/W
interrupts are directed to SPURIOUS_INIT_HDLR & S/W
interrupts to SPURIOUS_soft_HDLR.
1Ch :
Reserved
1Dh :
Initial EARLY_PM_INIT switch
1Eh :
Reserved
1Fh :
Load keyboard matrix (notebook platform)
20h :
Reserved
21h :
HPM initialization (notebook platform)
22h :
Reserved
23h :
1. Check validity of RTC value:
e.g. a value of 5Ah is an invalid value for RTC minute.
2. Load CMOS settings into BIOS stack. If CMOS checksum
fails, use default value instead.
3. Prepare BIOS resource map for PCI & PnP use. If ESCD is
valid, take into consideration of the ESCD’s legacy information.
4. Onboard clock generator initialization. Disable respective
clock resource to empty PCI & DIMM slots.
5. Early PCI initialization:
-Enumerate PCI bus number
-Assign memory & I/O resource
-Search for a valid VGA device & VGA BIOS, and put it into
C000:0.
Page: C-10
Prox-B501 USERcS MANUAL
Appendix
C
Trouble Shooting
24h
:
Reserved
25h
:
Reserved
26h
:
Reserved
27h
:
Initialize INT 09 buffer
28h
:
Reserved
29h
:
1. Program CPU internal mtrr (P6 & PII) for 0-640K memory
address.
2. Initialize the APIC for Pentium class CPU.
3. Program early chipset according to CMOS setup.
Example: onboard IDE controller.
4. Measure CPU speed.
5. Invoke video BIOS.
2Ah
:
Reserved
2Bh
:
Reserved
2Ch
:
Reserved
2Dh
:
1. Initialize multi-language
2. Put information on screen display, including Award title, CPU
type, CPU speed …
2Eh
:
Reserved
2Fh
:
Reserved
30h
:
Reserved
31h
:
Reserved
32h
:
Reserved
33h
:
Reset keyboard except Winbond 977 series Super I/O chips.
Prox-B501 USERcS MANUAL
Page: C-11
Appendix
C
Trouble Shooting
34h
:
Reserved
35h
:
Reserved
36h
:
Reserved
37h
:
Reserved
38h
:
Reserved
39h
:
Reserved
3Ah :
Reserved
3Bh
:
Reserved
3Ch
:
Test 8254
3Dh
:
Reserved
3Eh
:
Test 8259 interrupt mask bits for channel 1.
3Fh
:
Reserved
40h
:
Test 8259 interrupt mask bits for channel 2.
41h
:
Reserved
42h
:
Reserved
43h
:
Test 8259 functionality.
44h
:
Reserved
45h
:
Reserved
46h
:
Reserved
47h
:
Initialize EISA slot
Page: C-12
Prox-B501 USERcS MANUAL
Appendix
C
Trouble Shooting
48h
:
Reserved
49h
:
1. Calculate total memory by testing the last double word of each
64K page.
2. Program writes allocation for AMD K5 CPU.
4Ah :
Reserved
4Bh :
Reserved
4Ch :
Reserved
4Dh :
Reserved
4Eh :
1. Program MTRR of M1 CPU
2. Initialize L2 cache for P6 class CPU & program CPU with
proper cacheable range.
3. Initialize the APIC for P6 class CPU.
4. On MP platform, adjust the cacheable range to smaller one in
case the cacheable ranges between each CPU are not identical.
4Fh :
Reserved
50h
:
Initialize USB
51h
:
Reserved
52h
:
Test all memory (clear all extended memory to 0)
53h
:
Reserved
54h
:
Reserved
55h
:
Display number of processors (multi-processor platform)
56h
:
Reserved
57h
:
1. Display PnP logo
2. Early ISA PnP initialization
-Assign CSN to every PnP device.
Prox-B501 USERcS MANUAL
Page: C-13
Appendix
C
Trouble Shooting
58h
:
Reserved
59h
:
Initialize the combined Trend Anti-Virus code.
5Ah :
Reserved
5Bh :
(Optional Feature)
Show message for entering AWDFLASH.EXE from FDD
(optional)
5Ch :
Reserved
5Dh :
1. Initialize Init_Onboard_Super_IO switch.
2. Initialize Init_Onboard_AUDIO switch.
5Eh :
Reserved
5Fh :
Reserved
60h
:
Okay to enter Setup utility; i.e. not until this POST stage can users
enter the CMOS setup utility
61h
:
Reserved
62h
:
Reserved
63h
:
Reserved
64h
:
Reserved
65h
:
Initialize PS/2 Mouse
66h
:
Reserved
67h
:
Prepare memory size information for function call:
INT 15h ax=E820h
68h
:
Reserved
69h
:
Turn on L2 cache.
Page: C-14
Prox-B501 USERcS MANUAL
Appendix
C
Trouble Shooting
6Ah
:
Reserved
6Bh
:
Program chipset registers according to items described in Setup
and Auto-configuration table.
6Ch
:
Reserved
6Dh
:
1. Assign resources to all ISA PnP devices.
2. Auto assign ports to onboard COM ports if the corresponding
item in Setup is set to “AUTO”.
6Eh
:
Reserved
6Fh
:
1. Initialize floppy controller.
2. Set up floppy related fields in 40:hardware.
70h
:
Reserved
71h
:
Reserved
72h
:
Reserved
73h
:
(Optional Feature)
Enter AWDFLASH.EXE if:
- AWDFLASH is found in floppy drive.
- ALT+F2 is pressed
74h
:
Reserved
75h
:
Detect & install all IDE devices: HDD, LS120, ZIP, CDROM…..
76h
:
Reserved
77h
:
Detect serial ports and parallel ports
78h
:
Reserved
79h
:
Reserved
7Ah :
Detect and install co-processor
Prox-B501 USERcS MANUAL
Page: C-15
Appendix
C
Trouble Shooting
7Bh
:
Reserved
7Ch
:
Reserved
7Dh
:
Reserved
7Eh
:
Reserved
7Fh
:
1. Switch back to text mode if full screen logo is supported.
-If errors occur, report errors and wait for keys
-If no errors occur or F1 key is pressed to continue:
*Clear EPA or customization logo.
80h
:
Reserved
81h
:
Reserved
82h
:
1. Call chipset power management hook.
2. Recover the text fond used by EPA logo (not for full screen
logo).
3. If password is set, ask for password.
83h
:
Save all data in stack back to CMOS.
84h
:
Initialize ISA PnP boot devices.
85h
:
1. USB final initialization.
2. NET PC: Build SYSID structure.
3. Switch screen back to text mode.
4. Setup ACPI table at top of memory.
5. Invoke ISA adapter ROMs.
6. Assign IRQs to PCI devices.
7. Initialize APM.
8. Clear noise of IRQs.
86h
:
Reserved
87h
:
Reserved
Page: C-16
Prox-B501 USERcS MANUAL
Appendix
C
Trouble Shooting
88h
:
Reserved
89h
:
Reserved
90h
:
Reserved
91h
:
Reserved
92h
:
Reserved
93h
:
Read HDD boot sector information for Trend Anti-Virus code.
94h
:
1. Enable l2 cache.
2. Program boot up speed.
3. Chipset final initialization.
4. Power management final initialization.
5. Clear screen and display summary table
6. Program K6 write allocation.
7. Program P6 class write combining.
95h
:
1. Program daylight saving.
2. Update keyboard LED and typematic rate.
96h
:
1. Build MP table.
2. Build and update ESCD.
3. Set CMOS century to 20h or 19h.
4. Load CMOS time into DOS timer tick.
5. Build MSIRQ routing table.
FFh :
Boot attempt (INT 19h)
Prox-B501 USERcS MANUAL
Page: C-17
Appendix
C
Trouble Shooting
PRINTED IN TAIWAN
Page: C-18
Prox-B501 USERcS MANUAL
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement