Uniden | EZI30XLT | Specifications | Uniden EZI30XLT Specifications

EZI30XLT
Scanner
For more exciting new products please visit our website:
Australia: www.uniden.com.au
New Zealand: www.uniden.co.nz
IMPORTANT INFORMATION
PRECAUTIONS
Before you use this scanner, please read and observe the
following:
EARPHONE WARNING!
Use only a genuine Uniden earphone. An incorrect earphone
may be hazardous to your hearing. Turn down volume before
connecting the earphone and then adjust volume to suit.
WARNING!
Uniden does not represent this unit to be waterproof. To
reduce the risk of fire or electrical shock, do not expose this unit
to rain or moisture.
UNIDEN EZI30XLT
2
Scanner
CONTENTS
Important Information 2
Precautions
2
Contents About Your New EZI30XLT Sscanner 4
Country Mode (Australia/New Zealand) 4
5
Features 6
Understanding Scanning What is Scanning? 6
Conventional Scanning 6
Where To Obtain More Information 7
8
Included With Your Scanner 9
Setting Up Your Scanner
Installing and Replacing Batteries
9
Using Rechargeable Batteries 10
Connecting the Antenna 10
Connecting an Optional Antenna 11
Connecting the Earphone 11
Attaching the Belt Clip
12
EZI30XLT Controls and Display 13
A Look At The Keypad 14
A Look At The Display 16
17
Operation To turn Power ON or OFF
17
To Adjust the Squelch Level 17
To Adjust the Volume Level 17
Operating modes 17
18
Instant Channels Service Scan 18
Favourites Scan 19
Scanning Service & Favourites 19
Storing Frequencies 20
Editing Frequencies 21
Using Keylock 21
Using the Display Backlight 21
Troubleshooting 22
Resetting the Scanner 23
Care and Maintenance 24
General Use 24
Location 24
Cleaning 24
Repairs 24
Birdies 24
Specifications 25
26
Warranty UNIDEN EZI30XLT
3
Scanner
ABOUT YOUR EZI30XLT SCANNER
Thank you for purchasing a Uniden EZI30XLT Handheld
Scanner. The scanner is versatile, compact, and easy to use.
The EZI30XLT comes pre-programmed with frequencies organised into 8 Service banks for monitoring police, railroad,
fire, ambulance, FM radio, air, marine and UHF CB frequencies.
Each Service bank has a Favourites bank for storing your
favourite frequencies. Up to 210 frequencies can be stored in
Favourites banks. Frequencies in Favourites can be copied from
the Service bank. Manually store your favourite sports or events
frequencies found through the internet and other sources. Visit
the EZI30XLT page on the website for the latest information on
sports and events frequencies.
Australia: www.uniden.com.au
New Zealand: www.uniden.co.nz
Additionally you have 3 Instant channels which are one-touch
keys to store your 3 favourite frequencies.
COUNTRY MODE (AUSTRALIA/NEW ZEALAND)
The EZI30XLT is set to the Australian mode by default.
The Police, RailRoad, Fire and Ambulance banks have select
pre-programmed frequencies - one set for Australia and another
set for New Zealand. Switching the country mode alternates
between the select pre-programmed frequencies of these
service banks.
The country mode can be switched between Australia and New
Zealand as follows:
• Turn on the power while pressing down (Hold). The display
will show the current setting; AUS for Australian mode or nL
for New Zealand mode.
• Press
to change the setting.
• Press (Store) to store the country mode. The scanner
displays the volume level and starts in the last mode. The
country mode is remembered for the next power on.
UNIDEN EZI30XLT
4
Scanner
FEATURES
BAND COVERAGE
Range (MHz)
Step
Mode
(kHz)
75.0000 - 77.99375
6.25
Service
FM
VHF Low Band
78.0000 - 85.0000
6.25
FM
VHF Low Band
88.0000 - 107.9000
100
FMB
FM Broadcast
108.0000 - 136.9875
12.5
AM
Aircraft Band
137.0000 - 147.99375
6.25
FM
2 Meter Amateur Band
148.0000 - 174.0000
6.25
FM
VHF High Band
410.0000 - 489.0000
12.5
FM
Land Mobile Radio
“FMB” means FM Broadcast demodulation [WFM (Broadcast)].
PRE-PROGRAMMED SERVICE SCAN
8 banks of pre-programmed frequencies ready for scanning.
POLICE
FM Radio Broadcast
RAILROAD
AIRCRAFT Band
FIRE
MARINE
AMBULANCE
UHF CB
FAVOURITE SCAN
Up to 210 user programmable frequencies can be stored and
scanned in Favourites scan mode. Each SERVICE has a
FAVOURITES bank for storing and scanning up to 20 of your
favourite frequencies. An additional miscellaneous (MISC) bank
is available only in the Favourites mode for storing and scanning
an additional 50 favourites frequencies.
INSTANT CHANNEL
3 one-touch keys to store your 3 favourite frequencies.
DROPOUT DELAY
The scanner, during scan, pauses at the end of a transmission
to wait for a reply. Delay time is 2 seconds.
LCD BACKLIGHT
You can turn the orange LCD back light on/off.
KEY LOCK
Lets you lock the scanner’s keys to help prevent accidental
changes to the scanner’s programming.
MEMORY BACK UP
Keeps the frequencies stored in memory for an extended time if
the scanner loses power.
BATTERY LOW ALERT
Warns you when the battery power gets low.
UNIDEN EZI30XLT
5
Scanner
Understanding Scanning
This section provides you with background on how scanning
works. You don’t really need to know all of this to use your
scanner, but some background knowledge will help you get the
most from your EZI30XLT.
What is Scanning?
Unlike standard AM or FM radio stations, most two-way
communications do not transmit continuously. Your EZI30XLT
scans programmed channels until it finds an active frequency,
then stops on that frequency and remains on that channel as
long as the transmission continues. When the transmission
ends, the scanning cycle resumes until the scanner receives
another transmission.
Conventional Scanning
Conventional scanning is a relatively simple concept. Each
group of users in a conventional system is assigned a single
frequency (for simplex systems) or two frequencies (for repeater
systems). Any time one of them transmits, their transmission
always goes out on the same frequency. Up until the late 1980’s
this was the primary way that radio systems operated.
Even today, there are many 2-way radio users who operate
using a conventional system:
• Aircraft
• Emergency Services (Police/Fire/Ambulance)
• Railroad
• Broadcast FM stations
• UHF CB Radio
• Marine Radio
• Many business radio users
When you want to store a conventional system, all you need
to know is the frequencies they operate on. When you are
scanning a conventional system, the scanner stops very briefly
on each channel to see if there is activity. If there isn’t, the
scanner quickly moves to the next channel. If there is, then the
scanner pauses on the transmission until it is over.
UNIDEN EZI30XLT
6
Scanner
Understanding Scanning
Where To Obtain More Information
By itself, this manual really only provides part of what you need
to know to have fun scanning – how to program and use the
scanner.
Information On The Internet
The Internet is a great source for current frequencies and
information about scanning. Many web sites have lists of
frequencies for your area.
The EZI30XLT can tune to frequencies used at major sports and
events. Visit the EZI30XLT page on the website for the latest
information on sports and events frequencies.
Australia: www.uniden.com.au
New Zealand: www.uniden.co.nz
UNIDEN EZI30XLT
7
Scanner
Included With Your Scanner
EZI30XLT
Antenna
Earphone
3x AA Alkaline Batteries
EZI30XLT
Scanner
For more exciting new products please visit our website:
Australia: www.uniden.com.au
New Zealand: www.uniden.co.nz
Belt Clip
Owner’s Manual
Note: If any of these items are missing or damaged, contact
your place of purchase.
UNIDEN EZI30XLT
8
Scanner
Setting Up Your Scanner
These guidelines will help you install and use your new scanner:
• If your scanner receives interference or electrical noise, move
the scanner or its antenna away from the source.
• To improve the scanner’s reception, use an optional external
antenna designed for multiband coverage. (You can purchase
this type of antenna at a local electronics store). If the optional antenna has no cable, use 50 ohm coaxial cable
for lead-in. A mating plug might be necessary for the optional
antennas.
• Do not use the scanner in high-moisture environments such
as the kitchen or bathroom.
• Avoid placing the scanner in direct sunlight or near heating
elements or vents.
Installing and Replacing Batteries
You can power your scanner using three AA alkaline batteries.
1. Make sure the power is turned off.
2. If the belt clip is attached, remove it (See page 12).
3. Slide the battery compartment cover.
UNIDEN EZI30XLT
9
Scanner
Setting Up Your Scanner
4. Install three batteries in the compartment as indicated by the
polarity symbols (+ and -) marked inside.
5. Replace the cover.
Using Rechargeable Batteries
You can also use three rechargeable batteries (Ni-MH) to power
your scanner. Before you use rechargeable batteries, make sure
the batteries are fully charged.
Cautions:
• Use only fresh batteries of the required size and
recommended type.
• Always remove old or weak batteries. Batteries can leak
chemicals that destroy electronic circuits.
• Do not mix old and new batteries, different types
of batteries (standard, alkaline, or rechargeable), or
rechargeable batteries of different capacities.
Connecting the Antenna
UNIDEN EZI30XLT
10
Scanner
Setting Up Your Scanner
To attach the supplied flexible antenna to the connector on
the top of your scanner, align the slots around the antenna’s
connector with the tabs on the scanner’s BNC connector.
Then slide the antenna’s connector down over the scanner’s
connector and rotate the antenna connector’s outer ring
clockwise until it locks into place.
Connecting an Optional Antenna
The scanner’s BNC connector makes it easy to connect a variety
of optional antennas, including an external mobile antenna or
outdoor base station antenna.
Note: Always use 50-ohm, RG-58, or RG-8, coaxial cable to
connect an outdoor antenna. If the antenna is over 15 metres
from the scanner, use RG-8 lowloss dielectric coaxial cable.
You can get a BNC adapter at your local electronics store.
Connecting the Earphone
For private listening, you can plug the 3.5mm miniplug
earphone into the headphone jack on top of your scanner. This
automatically disconnects the internal speaker.
WARNING!
If you connect an external speaker to the scanner’s headphone
jack, never connect the audio output line to a power supply and
ground. This might damage the scanner.
UNIDEN EZI30XLT
11
Scanner
Setting Up Your Scanner
Attaching the Belt Clip
Pinch
To make your scanner easier to carry when you are on the go,
use the supplied belt clip. Slide the belt clip into the hanger
piece on the back of the scanner. To remove, slide up the belt
clip pulling the pinch at the middle of the belt clip.
UNIDEN EZI30XLT
12
Scanner
EZI30XLT CONTROLS AND DISPLAY
Antenna
Earphone Jack
Display
Keypad
UNIDEN EZI30XLT
1
Fav
Store
Srvc
Hold
Vol
Clr
2
Sq
3
Light
Pwr
13
Scanner
EZI30XLT CONTROLS AND DISPLAY
A Look At The Keypad
1
Fav
Store
Srvc
Hold
Vol
Clr
2
Sq
3
Light
Pwr
Your scanner’s keys have various functions labelled on the key
tops and below the keys.
Key Name
Fav
Store
Srvc
Fav
Hold
Store
Srvc
Hold
Fav
Store
Srvc
Hold
• Press to go to volume control mode.
• Press & hold this key to disable the
keypad.
Vol
Vol Clr
Sq
Clr
Sq Pwr
Vol
Light
Pwr
Clr
Light
Sq
• Press to go to squelch control mode.
• Press & hold to clear channel memory
in Favourite Scan Hold Mode or Instant
Channel Mode.
• Press to turn on/off the LCD back light.
• Press & hold to turn the power on/off.
• Press to move the digit to right in Edit
Favourite / Instant Channel Mode.
Pwr
Light
1
1
21
2
32
3
3
Description
Fav
Fav
Srvc
Fav
Srvc
Srvc
UNIDEN EZI30XLT
Store • Press to select Instant channel 1.
Vol
Store
Hold • Press & hold to store Instant channel
Store VolClr
Hold
Vol
Clr to select Instant channel 2.
Hold • Sq
Press
Sq
Clr & hold to store Instant channel
Pwr
• Press
SqPwr
Light
1.
2.
Pwrto select Instant channel 3.
• Light
Press
Light
• Press
& hold to store Instant channel 3.
• Press to move the digit to left in Edit
Favourite / Instant Channel Mode.
14
Scanner
EZI30XLT CONTROLS AND DISPLAY
Key Name
1
Fav
Store
Srvc
Hold
2
3
1
3
Store
Hold
11
• Press to toggle change the service
bank.
Clr • Press & hold to toggle between
Sq
Service Scan Mode and Favourite
Pwr Scan Mode. (Or between Service
Light
Scan Hold Mode and Favourite Scan
Hold Mode.)
Vol
• Press to Start/Stop Scan Mode.
• Press & hold to go to Programming
Channel Mode in Service Scan
Clr
Sq
Hold Mode or while monitoring a
frequency.
Pwr
Fav
Fav Store
Store
Light
• Press & hold to store the frequency in
Vol
Vol
Srvc
Srvc Hold
Hold
Programming Channel Mode.
Fav
Srvc
2
Description
Vol
Clr
Clr
Sq
Sq •
Press to change volume level in
volume
control mode.
Pwr
Pwr
Light
Light • Press to change squelch level in
squelch control mode.
• Press to change the direction of the
scan.
• Press to resume scanning while
monitoring a frequency.
• Press to select channels in Service
/ Favourite Scan Hold Mode or
Programming Channel Mode.
• Press for more than one second to
rapidly select channels upwards or
downwards in Service / Favourite
Scan Hold Mode or Programming
Channel Mode.
• Press to edit frequencies in Edit
Favourite / Instant Channel Mode.
• Press for more than one second to
rapidly edit frequencies upwards or
downwards in Edit Favourite / Instant
Channel Mode.
22
33
UNIDEN EZI30XLT
15
Scanner
EZI30XLT CONTROLS AND DISPLAY
A Look At The Display
The display has indicators that show the scanner’s current
operating status. The display information helps you understand
how your scanner operates.
FAV - appears when Favourites or Instant mode is selected.
POL
- appears when Police bank is selected.
RAIL
- appears when Railroad bank is selected.
FIRE
- appears during when Fire bank is selected.
1
Fav
Store
2 Vol
Srvc
Hold
- appears during when Ambulance bank is selected.
Clr
- appears when Instant channel 1 is selected.
Sq
- appears when Instant channel 2 is selected.
3 - appears when Instant channel 3 is selected.
AMBL
1 2
3
HOLD - appears when keylock is activated.
Light
- appears when Hold is selected during scanning
modes.
- appears during Instant mode
MISC - appears when Miscellaneous bank is selected
during Favourites mode.
FM
- appears when FM Radio band is selected.
AIR
- appears when Air band is selected.
MRN
- appears when Marine band is selected.
UCB
- appears when UHF CB band is selected.
Pwr
- appears when battery level is low.
UNIDEN EZI30XLT
16
Scanner
OPERATION
To turn Power ON or OFF
1. Press & hold (Pwr).
When power is turned
on the volume level is
displayed momentarily.
1
Fav
Store
Srvc
Hold
Vol
Clr
2
Sq
3
Light
Pwr
To Adjust the Squelch
What is the Squelch?
When there is no signal present on a particular frequency
the radio only hears noise. The Squelch feature mutes the
audio when there is no signal or no strong signal present. By
adjusting the squelch level you control how strong a signal
needs to be to open the squelch and unmute the audio.
1.Press (Sq) and then adjust using the / keys. The squelch
level can range from 0 (open squelch) to 10 (tight squelch).
Tip! Set the squelch level to 5 to start, you can always adjust
it later.
To Adjust the Volume
1.Press (Vol).
Fav
1
Then adjust using the / keys.
Srvc
The volume level can range from 0
(no volume) to 30 (maximum).2
Operating modes
Store
Hold
Vol
Sq
Clr
Pwr
3
Light
• INSTANT Channels (1), (2) and (3)
• SERVICE scan
• FAVOURITES scan
UNIDEN EZI30XLT
17
Scanner
OPERATION
Instant Channels
The INSTANT channels are 3 one-touch keys to
store your 3 favourite frequencies. The channels
remain empty until you store a frequency to them.
At any time press (1), (2) or (3) to select the
instant channel.
1
2
3
1 , 2 or 3 shows at the top of the display.
To store an Instant channel:
1. Select the desired Intant channel
(1), (2) or (3);
1
Fav
Store
Srvc
Hold
2
2. Press & hold (Store) to enter the
STORE mode. The editable digit flashes.
3. Use the / / / keys to select
the desired frequency.
4. Press & hold (Store) to store the
frequency to the instant channel.
Vol
Sq
Pwr
3
Light
Ex: Store Instant 2 ,
Select Desired Frequency
To store a frequency that is displayed
during SCAN mode to an Instant channel;
1. Press & hold (1), (2) or (3) to immediately store that
frequency to the Instant key.
To clear the Instant channel:
1. Press & hold (Clr) during Instant mode.
Service Scan
The Service mode scans the 8 pre-programmed SERVICE banks;
POL POLICE
FM FM Radio Broadcast
RAIL RAILROAD
AIR AIRCRAFT Band
FIRE FIRE
MRN MARINE
AMBL AMBULANCE
UCB UHF CB
UNIDEN EZI30XLT
18
Clr
Scanner
OPERATION
Favourites Scan
Each SERVICE bank has a FAVOURITES bank which remains
empty until you store your favourite frequencies to it.
An additional miscellaneous (MISC) bank is available in the
Favourites mode.
Scanning Service & Favourites
To go to scan mode or scan the
next bank:
1.
Press (Srvc/Fav). Scan starts
automatically. When there are no
frequencies stored in the Favourites
bank then the display flashes “noCH”.
Ex: Service scan, AIR bank
Ex: Favourites scan, no
channels
Note: Only one bank can be scanned at a time.
The banks can be changed in the following order;
POL > RAIL > FIRE > AMBL > MISC* > FM > AIR > MRN > UCB
*Available only in Favourites mode.
To switch scan modes between
Service scan and Favourite scan:
1.
Press & hold (Srvc/Fav).
In Service mode the FAV icon does
not show on the display.
In Favourites mode the FAV icon
shows on the display.
To pause scan:
Ex: Service scan
Ex: Favourites scan
1. Press (Hold) at any time to pause
scan on the current frequency.
2.
Use the / keys to go to the
previous/next frequency in the
service bank or the previous/next
channel in the favourites bank.
Ex: Service scan Hold
3. Press (Hold) again to resume scan.
UNIDEN EZI30XLT
19
Scanner
OPERATION
Storing Frequencies
To store a Service bank frequency to the Favourites bank:
1. Go to service scan mode. When a
desired frequency is found
press (Hold) to pause scan.
2.
Press & hold (Store) to enter the
STORE mode. The display toggles
between frequency and the next
available channel in the
Favourites bank.
3. Use the / keys to select the
desired favourites channel to
store the frequency to.
Ex: Service scan Hold
Ex: Store Favourites,
CH 01 (AIR)
Tip! Press (Srvc/Fav) to select the MISC favourites bank.
4. Press & hold (Store) to store the frequency.
The radio stays in the favourites mode.
To manually store a frequency to the Favourites bank:
1. Go to favourites mode and select desired bank.
2. Press (Hold) to pause scan.
3. Use
/
to select desired channel.
Ex: Store Favourites,
CH 02 (AIR)
4. Press & hold (Store) to enter the
STORE mode. The editable digit
flashes.
5. Use the / / / keys to select
the desired frequency.
Ex: Store Favourites,
Select Desired Frequency
(AIR)
6. Press & hold (Store) to store the
frequency.
To store a frequency to an Instant Channel
See Instant Channels on page 18.
UNIDEN EZI30XLT
20
Scanner
OPERATION
Editing Frequencies
1. Go to a desired Favourites or Instant channel.
2. Press & hold (Store) to enter the STORE mode. The editable digit flashes.
3. Use the / /
the frequency.
/
keys to edit
4. Press & hold (Store) to store
the frequency.
Ex: Edit Favourites, Select
Desired Frequency CH 03
(FIRE)
To clear the Favourite or Instant channel:
1. Press & hold (Clr) while the channel is displayed.
Using Keylock
Use the scanner’s keylock to protect it from accidental program
changes. When the scanner’s keys are locked, the only controls
), (Light / Pwr) and / when volume
that operate are (Vol /
level is displayed.
1. Press & hold (Vol /
) to turn key lock on/off.
A confirmation tone sounds.
appears while key lock is on.
Note: Using keylock does not prevent the scanner from
scanning channels.
Using the Display Backlight
1.
Press (Light/Pwr) to turn the backlight on/off.
The backlight is off when power is turned on.
The display lights for 30 seconds when backlight is
turned on.
UNIDEN EZI30XLT
21
Scanner
Troubleshooting
If your EZI30XLT is not performing properly, try the following
steps.
Problem
Possible Cause
Suggestion
Improper
reception.
The scanner’s
antenna might
need to be
adjusted.
Check the antenna
connection or move or
reposition the antenna.
Move the scanner.
You might be in a remote area
that could require an optional
multi-band antenna. Check
with your dealer or local
electronics store.
Scan
won’t
stop.
The squelch
might need to be
adjusted.
Adjust the squelch threshold.
See “To adjust the squelch” on
page 17.
The antenna
might need to be
adjusted.
Check the antenna
connection.
The channel’s
frequency might
not be stored in
favourites.
Make sure the channel’s
frequency is stored in the
scanner’s favourites bank.
The channel might Wait for a transmission on
not be active.
the channel.
Scan
won’t
start.
UNIDEN EZI30XLT
You must be
service or
favourites mode.
Press (Srvc/Fav). If HOLD
is showing press (Hold) to
resume.
The squelch
might need to be
adjusted.
Adjust the squelch threshold.
See “To adjust the squelch” on
page 17.
The antenna
might need to be
adjusted.
Check the antenna
connection.
22
Scanner
Troubleshooting
Resetting the Scanner
If the scanner’s display locks up or stops operating properly, you
might need to reset the scanner.
Caution:
This procedure clears all the information you have stored in
the scanner. Before you reset the scanner, try turning it off and
on to see if it begins working properly. Reset the scanner only
when you are sure it is not working properly.
1. Turn off the scanner.
2. While holding down (Hold) and (2), turn on the scanner. It
takes about 1 second to initialize and CLEAR appears.
UNIDEN EZI30XLT
23
Scanner
Care and Maintenance
Keep the scanner dry. If it gets wet, wipe it dry immediately. Use
and store the scanner only in normal temperature environments.
Handle the scanner carefully: do not drop it. Keep the scanner
away from dust and dirt, and wipe it with a damp cloth
occasionally to keep it looking new.
General Use
• Always write down the programmed frequencies in the event
of memory loss.
• If memory is lost, simply reprogram each channel. The
display shows - - - - - - in all channels when there has been a
memory loss.
• Always press each button firmly until you hear the entry tone
for that key entry.
Location
• Do not use the scanner in high-moisture environments such
as the kitchen or bathroom.
• Avoid placing the unit in direct sunlight or near heating elements
or vents.
• If the scanner receives strong interference or electrical noise,
move it or its antenna away from the source of the noise. If
possible, a higher elevation might provide better reception.
• Also try changing the height or angle of the antenna.
Cleaning
• Clean the outside of the scanner with a mild detergent.
• To prevent scratches, do not use abrasive cleaners or
solvents. Be careful not to rub the LCD window.
• Do not use excessive amounts of water.
Repairs
Do not attempt any repair. The scanner contains no user
serviceable parts.
Birdies
All radios can receive “birdies” (undesired signals). If your
scanner stops during Scan mode and no sound is heard, it might
be receiving a birdie. Birdies are internally generated signals
inherent in the electronics of the receiver.
Press
/
to resume scanning.
UNIDEN EZI30XLT
24
Scanner
Specifications
Channels (Favourites + Instant):
213
Frequency Range (in MHz)
See page 5
Sensitivity (12 dB SINAD) (Norminal)
78.0000 MHz (FM)
84.1250 MHz (FM)
90.0000 MHz (FMB)
107.5000 MHz (FMB)
118.8000 MHz (AM)
127.1750 MHz (AM)
135.5000 MHz (FM)
138.1500 MHz (FM)
162.4000 MHz (FM)
173.2250 MHz (FM)
410.5000 MHz (FM)
453.2500 MHz (FM)
488.8750 MHz (FM)
0.4 μV
0.3 μV
0.8 μV
0.9 μV
0.4 μV
0.4 μV
0.4 μV
0.3 μV
0.3 μV
0.3 μV
0.3 μV
0.3 μV
0.3 μV
Operating Temperature
Normal
Scan Rate:
IF Rejection (at 162.4 MHz)
–20°C to +60°C
27 channels per second (Nominal)
70 dB (Norminal)
IF Frequencies (Norminal)
1st IF
2nd IF
Audio Output
Built-in Speaker
70.950 MHz
450 kHz
490 mW maximum
32 mm dia, 24 ohm
Dynamic Type
Current Drain
Squelched
Full Output (Light off)
66 mA
190 mA
Power Requirements
3 AA Alkaline Batteries (4.5V DC),
or 3 AA Rechargeable Ni-MH Batteries (3.6V DC)
Antenna:
50 ohms (Impedance)
External Jacks:
Antenna Jack BNC Type
Ext. Earphone Jack 3.5 mm
Size (without antenna and belt clip):
53mm (W) x 28mm (D) x 104mm (H)
Weight (without Antenna and battery):
100 g
Features, specifications, and availability of optional accessories are all
subject to change without notice.
UNIDEN EZI30XLT
25
Scanner
WARRANTY
UNIDEN EZI30XLT SCANNER
IMPORTANT: Satisfactory evidence of the original purchase is
required for warranty service
Please refer to our Uniden website for any details or warranty durations
offered in addition to those contained below.
Warrantor: The warrantor is either Uniden Australia Pty Limited ABN 58
001 865 498 (“Uniden Aust”) or Uniden New Zealand Limited (“Uniden
NZ”) as the case may be.
Terms of Warranty: Uniden Aust/NZ warrants to the original retail
purchaser only that the EZI30XLT Radio (“the Product”), will be free from
defects in materials and craftsmanship for the duration of the warranty
period, subject to the limitations and exclusions set out below.
Warranty period: This warranty to the original retail purchaser is only
valid in the original country of purchase for a Product first purchased
either in Australia or New Zealand and will expire one (1) year from the
date of the original retail sale.
If a warranty claim is made, this warranty will not apply if the Product is
found by Uniden to be:
(A) Damaged or not maintained in a reasonable manner or as
recommended in the relevant Uniden Owner’s Manual;
(B) Modified, altered or used as part of any conversion kits,
subassemblies or any configurations not sold by Uniden Aust or
Uniden NZ;
(C) Improperly installed contrary to instructions contained in the relevant
Owner’s Manual
(D) Repaired by someone other than an authorized Uniden Repair Agent
in relation to a defect or malfunction covered by this warranty; or
(E) Used in conjunction with any equipment, parts or a system not
manufactured by Uniden.
Parts Covered: This warranty covers the Product and included
accessories.
User-generated Data: This warranty does not cover any claimed loss of
or damage to user-generated data (including but without limitation phone
numbers, addresses and images) that may be stored on your Product.
Statement of Remedy: If the Product is found not to conform to this
warranty as stated above, the Warrantor, at its discretion, will either
repair the defect or replace the Product without any charge for parts or
service. This warranty does not include any reimbursement or payment
of any consequential damages claimed to arise from a Product’s failure
to comply with the warranty.
UNIDEN EZI30XLT
26
Scanner
WARRANTY
Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund
for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
This warranty is in addition to and sits alongside your rights under either
the COMPETITION AND CONSUMER ACT 2010 (Australia) or the
CONSUMER GUARANTEES ACT (New Zealand) as the case may be,
none of which can be excluded.
Procedure for obtaining warranty service: Depending on the country
in which the Product was first purchased, if you believe that your Product
does not conform with this warranty, you should deliver the Product,
together with satisfactory evidence of your original purchase (such as
a legible copy of the sales docket) to Uniden at the addresses shown
below. You should contact Uniden regarding any compensation that may
be payable for your expenses incurred in making a warranty claim. Prior
to delivery, we recommend that you make a backup copy of any phone
numbers, images or other data stored on your Product, in case it is lost
or damaged during warranty service.
UNIDEN AUSTRALIA PTY LTD
Service Division
345 Princes Highway,
Rockdale, NSW 2216
Phone: 1300 366 895
Email: custservice@uniden.com.au
UNIDEN EZI30XLT
UNIDEN NEW ZEALAND LTD
Service Division
150 Harris Road, East Tamaki
Auckland 2013
Phone: (09) 273 8377
Email: service@uniden.co.nz
27
Scanner
THANK YOU FOR BUYING A UNIDEN PRODUCT.
© 2011 Uniden Australia Pty Limited. Uniden New Zealand Ltd.
Printed in PRC. UBZZ01366ZB(1)
Download PDF