UG-893: Evaluating the 8-Lead MSOP Devices in the Switch/Mux Portfolio (Rev. 0) PDF

UG-893: Evaluating the 8-Lead MSOP Devices in the Switch/Mux Portfolio (Rev. 0) PDF
Evaluation Board User Guide
UG-893
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluating the 8-Lead MSOP Devices in the Switch/Mux Portfolio
FEATURES
GENERAL DESCRIPTION
8-lead MSOP evaluation board
Clamp to allow the main device to be changed easily
Gold pin connectors to allow the addition of passive
components
SMB connectors for the input/output of signals
Additional space on board to allow for prototyping
The EVAL-8MSOPEBZ evaluation board is for 8-lead MSOP
devices in the switch/mux portfolio that are purchased separately.
A clamp is supplied with the EVAL-8MSOPEBZ evaluation
board so that the device can be secured to the evaluation board
without the need for soldering which makes the board reusable
for multiple devices.
EVALUATION KIT CONTENTS
Figure 1 shows the EVAL-8MSOPEBZ evaluation board. The
device can be clamped or soldered to the center of the evaluation
board. Each pin of the device is broken out to a link that can be
set to either VDD or GND. A wire screw terminal supplies VDD
and GND. SMB connectors are on the board to allow additional
external signals to be supplied to the device. In addition, there is
space available at the top of the board for prototyping.
EVAL-8MSOPEBZ evaluation board
ONLINE RESOURCES
Documents needed
Data sheet of the device being evaluated
EVAL-8MSOPEBZ user guide
Full specifications of the device under test (DUT) are available in
the product data sheet, which should be consulted in conjunction
with this user guide when using the evaluation board.
EQUIPMENT NEEDED
Device being evaluated
DC voltage source
Analog signal source
Method to measure voltage, such as a digital multimeter (DMM)
13688-001
EVALUATION BOARD PHOTOGRAPH
Figure 1.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 6
UG-893
Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Power Supply..................................................................................3
Evaluation Kit Contents ................................................................... 1
Link Headers ..................................................................................3
Online Resources .............................................................................. 1
SMB Connectors............................................................................3
Equipment Needed ........................................................................... 1
Input Signal Traces ........................................................................3
General Description ......................................................................... 1
Evaluation Board Schematics and Artwork ...................................4
Evaluation Board Photograph ......................................................... 1
Ordering Information .......................................................................6
Revision History ............................................................................... 2
Bill of Materials ..............................................................................6
Evaluation Board Hardware ............................................................ 3
REVISION HISTORY
11/15—Revision 0: Initial Version
Rev. 0 | Page 2 of 6
Evaluation Board User Guide
UG-893
EVALUATION BOARD HARDWARE
Use the EVAL-8MSOPEBZ to evaluate the 8-lead MSOP devices
in the switch/mux portfolio. Figure 1 shows the evaluation board.
POWER SUPPLY
Connector J5 provides the ability to supply VDD and GND
supplies to the board. These supplies can then be selected for
each pin of the device by setting the link headers to either VDD
or GND. When a VSS supply is needed, apply the voltage
directly to the pin of the device. An example of how this is done
is by removing the link and then supplying the required voltage
to the central pin of the header or to the gold pin connectors on
the relevant trace.
LINK HEADERS
The link headers supply the DUT with either VDD or GND.
Each header is designated K1 to K8, with the number
corresponding to the pin number of the device. Table 1
summarizes the link headers and how they function on the
evaluation board.
Table 1. Link Header Descriptions
Label
K1to K8
Position
H
L
Description
VDD
GND
SMB CONNECTORS
There are four SMB connectors on evaluation board, J1 to J4.
When an SMB cable is one of these connectors, the signal
becomes available on P1 to P4. Apply this signal to the pin of
the device by forming a connection from P1 to P4 to a gold pin
connector found on the relevant trace.
INPUT SIGNAL TRACES
Each trace includes three sets of gold pin connectors, two of
which can place a load on the signal path to ground and another
that is in series with the signal path. The three sets of gold pin
connectors can create a simple resistor capacitor (RC) filter.
Rev. 0 | Page 3 of 6
UG-893
Evaluation Board User Guide
13688-002
EVALUATION BOARD SCHEMATIC AND ARTWORK
13688-003
Figure 2. EVAL-8MSOPEBZ Evaluation Board Schematic
Figure 3. EVAL-8MSOPEBZ Silkscreen
Rev. 0 | Page 4 of 6
UG-893
13688-004
Evaluation Board User Guide
13688-005
Figure 4. EVAL-8MSOPEBZ Top Layer
Figure 5. EVAL-8MSOPEBZ Bottom Layer
Rev. 0 | Page 5 of 6
UG-893
Evaluation Board User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 2.
Reference Designator
C1
C2
C3 to C26
J1 to J4
J5
K1 to K8
P1 to P4
T1 to T8
Description
0.1 µF, 50 V, X7R, ceramic capacitor
10 µF, 10 V tantalum capacitor
Harwin subminiature sockets (2)
SMB sockets
2-pin terminal block (5 mm pitch)
Jumper blocks using 3-pin SIP header
Harwin subminiature sockets (2)
Test points
Manufacturer Part Number
GRM21BR71H104KA01L
TAJB106K016RNJ
H3153-01
1206013
KRM 02
M20-9990345 and M7566-05
H3153-01
20-313137
Stock Code
FEC 2408531
FEC 498-737
FEC 2120079
FEC 310-682
FEC 151-785
FEC 512-047 and 150-411
FEC 2120079
FEC 240-345
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG13688-0-11/15(0)
Rev. 0 | Page 6 of 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement