Evaluation Board User Guide

UG-893

One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com

Evaluating the 8-Lead MSOP Devices in the Switch/Mux Portfolio

FEATURES

8-lead MSOP evaluation board

Clamp to allow the main device to be changed easily

Gold pin connectors to allow the addition of passive components

SMB connectors for the input/output of signals

Additional space on board to allow for prototyping

EVALUATION KIT CONTENTS

EVAL-8MSOPEBZ evaluation board

ONLINE RESOURCES

Documents needed

Data sheet of the device being evaluated

EVAL-8MSOPEBZ user guide

EQUIPMENT NEEDED

Device being evaluated

DC voltage source

Analog signal source

Method to measure voltage, such as a digital multimeter (DMM)

GENERAL DESCRIPTION

The EVAL-8MSOPEBZ evaluation board is for 8-lead MSOP devices in the switch/mux portfolio that are purchased separately.

A clamp is supplied with the EVAL-8MSOPEBZ evaluation board so that the device can be secured to the evaluation board without the need for soldering which makes the board reusable for multiple devices.

Figure 1 shows the

EVAL-8MSOPEBZ evaluation board. The device can be clamped or soldered to the center of the evaluation board. Each pin of the device is broken out to a link that can be set to either VDD or GND. A wire screw terminal supplies VDD and GND. SMB connectors are on the board to allow additional external signals to be supplied to the device. In addition, there is space available at the top of the board for prototyping.

Full specifications of the device under test (DUT) are available in the product data sheet, which should be consulted in conjunction with this user guide when using the evaluation board.

EVALUATION BOARD PHOTOGRAPH

PLEASE SEE THE LAST PAGE FOR AN IMPORTANT

WARNING AND LEGAL TERMS AND CONDITIONS.

Figure 1.

Rev. 0 | Page 1 of 6

UG-893

TABLE OF CONTENTS

Features .............................................................................................. 1

Evaluation Kit Contents ................................................................... 1

Online Resources .............................................................................. 1

Equipment Needed ........................................................................... 1

General Description ......................................................................... 1

Evaluation Board Photograph ......................................................... 1

Revision History ............................................................................... 2

Evaluation Board Hardware ............................................................ 3

REVISION HISTORY

11/15—Revision 0: Initial Version

Evaluation Board User Guide

Power Supply ..................................................................................3

Link Headers ..................................................................................3

SMB Connectors............................................................................3

Input Signal Traces ........................................................................3

Evaluation Board Schematics and Artwork ...................................4

Ordering Information .......................................................................6

Bill of Materials ..............................................................................6

Rev. 0 | Page 2 of 6

Evaluation Board User Guide

EVALUATION BOARD HARDWARE

Use the EVAL-8MSOPEBZ to evaluate the 8-lead MSOP devices

in the switch/mux portfolio. Figure 1 shows the evaluation board.

POWER SUPPLY

Connector J5 provides the ability to supply VDD and GND supplies to the board. These supplies can then be selected for each pin of the device by setting the link headers to either VDD or GND. When a VSS supply is needed, apply the voltage directly to the pin of the device. An example of how this is done is by removing the link and then supplying the required voltage to the central pin of the header or to the gold pin connectors on the relevant trace.

LINK HEADERS

The link headers supply the DUT with either VDD or GND.

Each header is designated K1 to K8, with the number

corresponding to the pin number of the device. Table 1

summarizes the link headers and how they function on the evaluation board.

UG-893

Table 1. Link Header Descriptions

Label Position Description

K1to K8 H

L

VDD

GND

SMB CONNECTORS

There are four SMB connectors on evaluation board, J1 to J4.

When an SMB cable is one of these connectors, the signal becomes available on P1 to P4. Apply this signal to the pin of the device by forming a connection from P1 to P4 to a gold pin connector found on the relevant trace.

INPUT SIGNAL TRACES

Each trace includes three sets of gold pin connectors, two of which can place a load on the signal path to ground and another that is in series with the signal path. The three sets of gold pin connectors can create a simple resistor capacitor (RC) filter.

Rev. 0 | Page 3 of 6

UG-893

EVALUATION BOARD SCHEMATIC AND ARTWORK

Evaluation Board User Guide

Figure 2. EVAL-8MSOPEBZ Evaluation Board Schematic

Figure 3. EVAL-8MSOPEBZ Silkscreen

Rev. 0 | Page 4 of 6

Evaluation Board User Guide

Figure 4. EVAL-8MSOPEBZ Top Layer

Figure 5. EVAL-8MSOPEBZ Bottom Layer

Rev. 0 | Page 5 of 6

UG-893

UG-893

ORDERING INFORMATION

BILL OF MATERIALS

Table 2.

Reference Designator

C1

C2

C3 to C26

J1 to J4

J5

K1 to K8

P1 to P4

T1 to T8

Description

0.1 µF, 50 V, X7R, ceramic capacitor

10 µF, 10 V tantalum capacitor

Harwin subminiature sockets (2)

SMB sockets

2-pin terminal block (5 mm pitch)

Jumper blocks using 3-pin SIP header

Harwin subminiature sockets (2)

Test points

Evaluation Board User Guide

Manufacturer Part Number

GRM21BR71H104KA01L

TAJB106K016RNJ

H3153-01

1206013

KRM 02

M20-9990345 and M7566-05

H3153-01

20-313137

Stock Code

FEC 2408531

FEC 498-737

FEC 2120079

FEC 310-682

FEC 151-785

FEC 512-047 and 150-411

FEC 2120079

FEC 240-345

ESD Caution

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

Legal Terms and Conditions

By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.

(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term

“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.

Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO

WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED

TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL

PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF

THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE

AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable

United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of

Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

©2015 Analog Devices, Inc. All rights reserved. Trademarks and

registered trademarks are the property of their respective owners.

UG13688-0-11/15(0)

Rev. 0 | Page 6 of 6