Becker BDi Revo 9981 Assembly Instructions

Component List a s s e m b l y i n s t r u c t i o n s

R evo

9981 bdiusa

.

com customerservice

@ bdiusa

.

com

Your Revo Home Theater Furniture is engineered for easy assembly. Carefully follow this procedure to prevent any damage.

A Glass Shelf x 2

Placement and Maintenance

Revo Home Theater Furniture is designed for indoor use on level floors. Clean glass with glass cleaner, and steel parts and wood veneer with a moist cloth.

B Shelf Pin x 8

Pre-installed

C Retention Clip x 8

Pre-installed

Step 1

Unpack and identify the parts listed above. The assembly workspace should be a non-marring surface such as carpet. For missing hardware pieces, please contact BDI Customer Service at [email protected]. For all other concerns, please contact your BDI Retailer.

D Phillips Screwdriver

x 1

E Allen Wrench x 1

Step 2

Revo 9981 features a swiveling base. Note that Swivel-Lock Pins

(F) are factory-installed at Position 1 enabling the stand to swivel

15-degrees to left and 15-degrees to right.

F Swivel-Lock Pin x 2

Pre-installed

To lock the stand in a fixed position, use provided Allen Wrench

(E) to remove both Swivel-Lock Pins (F) from Position 1 (factory

position) and re-install them at Position 2.

Position 2

Position 1

NOTE: Choosing not to use the

Swivel-Lock Pins (F) will enable

360-degrees of rotation.

F

Front

Designed by Louis Lara.

These distinctive product configurations are protected by US and international patents, trade dress, and/or copyright laws.

BDI are trademarks of Becker Designed, Inc. All Rights reserved. ©2009, BDI

9981REV092409v8

1

Retention clip (C)

Shelf pin (B)

A x 2

Step 2

Confirm that Shelf Pins (B) are pre-installed.

In order to adjust height, one must remove the glass retention clip (secured by the shelf pin) that holds the glass shelves in place.

1. Loosen the 4 Shelf Pins (B)

1 turn with Phillips Screwdriver

(D).

2.

3.

4.

Remove

Unscrew

Retention Clips (C) ( x 4 )

Shelf Pins (B) completely

Reposition the desired height

Shelf Pins (B) at

Secure Glass Shelves

To secure the shelves on your Revo unit, it is necessary to use the Retention Clip (C), which is secured by the Shelf Pin (B).

5.

6.

Install

Install

Glass Shelves (A x 2)

Retention Clips (C)

“Pin Assembly Diagram”

7. Secure by tightening the as shown in

Shelf Pin (B) with Phillips Screwdriver (D).

1

Pin Assembly Diagram

Detail of Shelf Pin (B) and

Retention Clip (C)

4 1 : Retention clip (C)

2 : Glass Shelf (A)

3 : Shelf Pin (B)

4 : Cabinet wall

4

1

2 assembly instructions bdiusa

.

com customerservice

@ bdiusa

.

com

Step 4

Install Back Panel.

The back panel comes pre-installed. Follow illustrations below for installation and removal.

Step 5

Adjust Door Hinges (if needed)

If the cabinet’s doors appear out of alignment, this condition can be corrected with minor adjustment to the European hinges on each door.

Because these hinges are infinitely adjustable, adjusting one hinge element can sometimes cause the need for adjustments to other elements. But with a few adjustments, you can modify the orientation of the cabinet doors to make sure that they hang perfectly within your cabinet.

2.*

2.

2.

3.

2.

1.

3.

2.*

1.

3.

3.

1.

1.

Figure 1 Figure 2

Use a Phillips screwdriver to adjust Revo’s door hinges:

• By adjusting Screw 1, the door will move LEFT or RIGHT within the frame. Make minor adjustments at both top and bottom hinges for best results.

• By adjusting Screw(s) 2, the door will move UP or DOWN within the frame (the top and bottom hinges must be adjusted the same degree).

NOTE: I f your hinges have a Slotted Mounting Plate (as shown in Figure 2): Loosen Screws 2 one complete turn, raise or lower door, then hold in position while tightening Screws 2 (on both hinges).

• By adjusting Screw 3 the entire door will move IN or OUT, opening or closing the gap between the door frame and cabinet. (This screw rarely needs adjustment.)

3 assembly instructions bdiusa

.

com customerservice

@ bdiusa

.

com