EVAL-6SOT23EBZ User Guide UG-948

EVAL-6SOT23EBZ User Guide UG-948
EVAL-6SOT23EBZ User Guide
UG-948
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for 6-Lead SOT-23 Devices in the Switches and Multiplexers Portfolio
FEATURES
GENERAL DESCRIPTION
6-lead SOT-23 evaluation board
Clamp allows the main device to be changed easily
Gold pin connectors allow the addition of passive components
SMB connectors for the input/output of signals
Additional space on board to allow for prototyping
The EVAL-6SOT23EBZ evaluation board evaluates 6-lead SOT-23
devices in the Switches and Multiplexers Portfolio that are
purchased separately. A clamp is supplied with the EVAL6SOT23EBZ to secure a 6-lead SOT-23 device to the evaluation
board without the need for soldering, making the board reusable
for multiple devices.
EVALUATION KIT CONTENTS
Figure 1 shows the EVAL-6SOT23EBZ evaluation board. A device
can be clamped or soldered to the center of the evaluation board.
Each pin of the device has a corresponding link from K1 to K6
that can be set to either VDD or GND. A wire screw terminal
supplies VDD and GND. SMB connectors on the board allow
additional external signals to be supplied to the device. In addition,
there is space available at the top of the board for prototyping.
EVAL-6SOT23EBZ evaluation board
ONLINE RESOURCES
Documents Needed
Data sheet of the device being evaluated
EVAL-6SOT23EBZ user guide
EQUIPMENT NEEDED
Full specifications of the device under test (DUT) are available in
the corresponding product data sheet, which should be consulted
in conjunction with this user guide when using the evaluation board.
Device being evaluated
DC voltage source
Analog signal source
Method to measure voltage, such as a digital multimeter (DMM)
14322-001
EVALUATION BOARD PHOTOGRAPH
Figure 1.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 6
UG-948
EVAL-6SOT23EBZ User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1 Power Supply..................................................................................3 Evaluation Kit Contents ................................................................... 1 Link Headers ..................................................................................3 Online Resources .............................................................................. 1 SMB Connectors............................................................................3 Equipment Needed ........................................................................... 1 Input Signal Traces ........................................................................3 General Description ......................................................................... 1 Evaluation Board Schematic and Artwork.....................................4 Evaluation Board Photograph......................................................... 1 Ordering Information .......................................................................6 Revision History ............................................................................... 2 Bill of Materials ..............................................................................6 Evaluation Board Hardware ............................................................ 3 REVISION HISTORY
4/16—Revision 0: Initial Version
Rev. 0 | Page 2 of 6
EVAL-6SOT23EBZ User Guide
UG-948
EVALUATION BOARD HARDWARE
POWER SUPPLY
Table 1. Link Header Descriptions
Connector J5 supplies the VDD and GND supplies to the
board. These supplies can be selected for each pin of the device
by setting the link headers to either VDD or GND. When a VSS
supply is needed, apply the voltage directly to the VSS or GND pin
of the device by removing the corresponding link.
LINK HEADERS
The link headers supply the DUT with either a VDD or GND
supply. The headers are designated K1 to K6 with the number
corresponding to the pin number of the device. Table 1
summarizes the link headers and how they function on the
evaluation board.
Label
K1to K6
Position
H
L
Description
VDD
GND
SMB CONNECTORS
There are four SMB connectors on evaluation board, J1 to J4.
When an SMB cable is connected to one of these connectors,
the input signal becomes available on the corresponding port
from P1 to P4. Apply this signal to the pin of the device by
forming a connection from P1 to P4 to a gold pin connector
found on the relevant trace.
INPUT SIGNAL TRACES
Each trace includes three sets of gold pin connectors, two sets
that can place a load on the signal path to ground and another set
that is in series with the signal path. The three sets of gold pin
connectors can create a simple resistor capacitor (RC) filter.
Rev. 0 | Page 3 of 6
UG-948
EVAL-6SOT23EBZ User Guide
14322-002
EVALUATION BOARD SCHEMATIC AND ARTWORK
14322-005
Figure 2. EVAL-6SOT23EBZ Evaluation Board Schematic
Figure 3. EVAL-6SOT23EBZ Silkscreen
Rev. 0 | Page 4 of 6
UG-948
14322-003
EVAL-6SOT23EBZ User Guide
14322-004
Figure 4. EVAL-6SOT23EBZ Top Layer
Figure 5. EVAL-6SOT23EBZ Bottom Layer
Rev. 0 | Page 5 of 6
UG-948
EVAL-6SOT23EBZ User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 2.
Reference Designator
C1
C2
C3 to C20
J1 to J4
J5
K1 to K6
P1 to P4
T1 to T6
Description
0.1 μF, 50 V, X7R, ceramic capacitor
10 μF, 10 V tantalum capacitor
Harwin subminiature sockets (2)
SMB sockets
2-pin terminal block (5 mm pitch)
Jumper blocks using 3-pin SIP header
Harwin subminiature sockets (2)
Test points
Part Number
GRM21BR71H104KA01L
TAJB106K016RNJ
H3153-01
1206013
KRM 02
M20-9990345 and M7566-05
H3153-01
20-313137
Stock Code
FEC 2408531
FEC 498-737
FEC 2120079
FEC 310-682
FEC 151-785
FEC 512-047 and 150-411
FEC 2120079
FEC 240-345
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until
you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices,
Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer
may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written
notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED,
RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF
INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S
POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES
SHALL BE LIMITED TO THE AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will
comply with all applicable United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of
the Commonwealth of Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts,
and Customer hereby submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is
expressly disclaimed.
©2016 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG14322-0-4/16(0)
Rev. 0 | Page 6 of 6
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement