Evaluation Board User Guide UG-098

Evaluation Board User Guide UG-098
Evaluation Board User Guide
UG-098
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for ADF4360-3 Integrated PLL and VCO Frequency Synthesizer
FEATURES
GENERAL DESCRIPTION
Self-contained board for generating RF frequencies
Flexibility for reference input, PFD frequency, and loop
bandwidth
Accompanying software allows complete control of
synthesizer functions from a PC
USB/battery-operated 9 V supplies
Typical phase noise performance of −141 dBc/Hz at 3 MHz offset
Typical spurious performance of −65dBc at 200 kHz offset
(1.8 GHz output)
The EV-ADF4360-3EB1Z evaluation board is designed to allow
the user to evaluate the performance of the ADF4360-3 frequency
synthesizer consisting of an integrated PLL and VCO (see Figure 1).
It contains the ADF4360-3BCPZ, a USB connector, and SMA
connectors for the RF outputs. Unpopulated SMA footprints are
available for the power supplies, the chip enable (CE), and the
external reference input. The evaluation board also contains the
loop filter to complete the PLL. It can be modified as necessary for
the PLL requirements of the user. A USB cable is included with
the board to allow software programmability from a PC.
The package also contains a CD with Windows® software to allow
quick, user-friendly programming of the synthesizer. The CD
contains additional PLL data sheets, technical notes, articles, and
ADIsimPLL™ V3.4 (Analog Devices, Inc., PLL simulation
software). More information is available at www.analog.com/pll.
08882-001
EVALUATION BOARD PHOTOGRAPH
Figure 1.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. B | Page 1 of 12
UG-098
Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1 Windows XP OS ............................................................................4 General Description ......................................................................... 1 Windows Vista OS and Windows 7 (32-Bit) OS..........................5 Evaluation Board Photograph......................................................... 1 Windows 7 64-Bit OS ...................................................................5 Revision History ............................................................................... 2 Using the Evaluation Board Software .............................................6 Evaluation Board Hardware ............................................................ 3 Evaluation Board Schematic ............................................................8 RF Output Stages .......................................................................... 3 Ordering Information.................................................................... 11 Evaluation Board Software Quick Start Procedures .................... 4 Bill of Materials........................................................................... 11 REVISION HISTORY
3/12—Rev. A to Rev. B
Changed ADF4360-3EBZ1 to EV-ADF4360-3EB1Z.....Throughout
Changes to Using the Evaluation Board Software Section ................6
9/11—Rev. 0 to Rev. A
Changes to Features Section and Figure 1..................................... 1
Changes to Evaluation Board Hardware Section ......................... 3
Added Evaluation Board Software Quick Start Procedures
Section................................................................................................ 4
Changes to Using the Evaluation Board Software Section.......... 6
Changes to Evaluation Board Schematics Section ....................... 8
Changes to Bill of Materials Section ............................................ 11
7/10—Revision 0: Initial Version
Rev. B | Page 2 of 12
Evaluation Board User Guide
UG-098
EVALUATION BOARD HARDWARE
The evaluation board comes with a cable to connect it to the
USB port of a PC. The silkscreen and cable diagram for the
evaluation board are shown in Figure 2. The board schematics
are shown in Figure 9 through Figure 11.
Users may provide their own power supplies using the J4 and J5
connectors, as shown in Figure 2. Hardware power-down using
the CE pin can be controlled by inserting an SMA connector
into J6 and removing R12.
The on-board filter is a third-order, passive, low-pass filter. The
filter contains three capacitors (C13, C14, and C15) plus two
resistors (R10 and R11). The footprint for R10 is located on the
underside of the board. The design parameters for the loop
filter are for a center frequency of 1800 MHz a PFD frequency
of 200 kHz, and a low-pass filter bandwidth of 10 kHz. To design a
filter for different frequency setups, use the ADIsimPLL simulation
software.
RF OUTPUT STAGES
08882-002
The output stage of the board contains a tuned load for the
particular frequency of operation. The particular network inserted
in the board is optimized for 1800 MHz operation. This consists
of a 2.2 nH shunt inductor, a 10 pF series capacitor, and a 2.2 nH
series inductor. If in doubt, use a 50 Ω resistor instead of the
shunt inductor, a 100 pF bypass capacitor, and a series 0 Ω
resistor. It is important that the same components be placed
on the RFOUTA and RFOUTB lines. In addition, it is essential that
both outputs be terminated with 50 Ω loads. Otherwise, the
output power is not optimum, and in some cases, the part may
malfunction.
Figure 2. Evaluation Board Silkscreen—Top View
The board is powered from a single 9 V battery, or from the
USB supply, by changing the position of Switch SW1. All
components necessary for LO generation are catered for on-board.
A 10 MHz TCXO from Fox Electronics provides the necessary
reference input. Otherwise, an external reference signal can be
connected via J3. The PLL comprises the ADF4360-3BCPZ and
a passive loop filter. The VCO output from RFOUTA is available
through the standard SMA Connector J1 and the complementary RFOUTB VCO output is available from J2.
Rev. B | Page 3 of 12
UG-098
Evaluation Board User Guide
EVALUATION BOARD SOFTWARE QUICK START PROCEDURES
The control software and USB drivers for the EV-ADF4360-3EB1Z
accompany the EV-ADF4360-3EB1Z on a CD. To install the
software, use the following steps:
1.
2.
Open ADF4360_Setup.msi.
The install wizard guides you through the installation
process. The software and USB drivers will be installed
in the default directory called C:\Program Files\Analog
Devices\ADF4360.
3.
4.
5.
Browse to C:\Program Files\Analog Devices\ADF4360 or
the location where you installed the ADF4360 software.
Click Continue Anyway when asked about Windows Logo
testing.
If the install was successful, the message box in Figure 4
appears.
WINDOWS XP OS
Figure 4. Successful Install
Once you have installed the software, install the USB drivers.
To do so, use the following steps:
2.
Plug in a USB cable to the USB connector on the
evaluation board. The Found New Hardware box
appears. See Figure 3.
Choose Install from a list or specified location
(Advanced).
08882-003
1.
08882-004
The software requires Microsoft’s .NET Framework Version 2.0
or later to be installed on your machine. The installer automatically downloads the framework from the Microsoft website if
you do not have this installed. If you do not have an Internet
connection or have a slow connection on the PC, then you
can install the .NET framework directly from the CD. Do
this by double-clicking dotnetfx.exe. Once installed, run
the ADF4360_Setup.msi again.
Figure 3. New Hardware Wizard
Rev. B | Page 4 of 12
Evaluation Board User Guide
UG-098
3.
WINDOWS VISTA OS AND WINDOWS 7 (32-BIT) OS
For Windows Vista or Windows 7 (32-bit), you need to
manually install the drivers. To do so, use the following steps:
Find the new unknown device (the evaluation board)
in Device Manager and double-click it to open the
properties. The device should be Unknown device,
under Other devices (see Figure 5).
08882-007
7.
08882-005
1.
4.
5.
6.
On the Update Driver Software dialog box, choose
Browse my computer for driver software.
Browse to C:\Program Files\Analog Devices\ADF4360.
Click OK or Next.
If prompted by Windows Security, choose Install this
driver software anyway.
If the install was successful, the message box in Figure 7
appears.
Figure 7. Successful Install
Figure 5. Device Manager
WINDOWS 7 64-BIT OS
Click Update Driver in the properties window (see
Figure 6).
If you are using Windows 7 64-bit OS, it is recommended to
download Windows XP Mode (a Windows XP emulator) from
Microsoft to run the evaluation board software.
Windows XP Mode allows the device driver package to digitally
sign allowing you to use Windows 7 64-bit OS in native mode.
08882-006
2.
Figure 6. Unknown Device Properties
Rev. B | Page 5 of 12
UG-098
Evaluation Board User Guide
USING THE EVALUATION BOARD SOFTWARE
The control software for the EV-ADF4360-xEB1Z accompanies
the EV-ADF4360-xEB1Z on a CD. To install the software, see
the Evaluation Board Software Quick Start Procedure section.
To run the software, click the ADF4360.exe file on the desktop
or in the Start menu.
The Settings section controls the charge pump current setting,
the output power setting, and the multiplexer output setting.
Use the Frequency Settings section to control the output
frequency. The user can input the desired output frequency to
the RF Output Frequency text box (in megahertz).
The main interface window appears (see Figure 8). Confirm
that Analog Devices RFG.L Eval Board connected is displayed
at the top of the window. Otherwise, the software has no connection to the evaluation board.
In the Registers tab, the user can manually input the desired
value to be written to the registers.
The evaluation board can be connected and disconnected while
the software is running. Note that when connecting the board,
it takes about 5 seconds for the status label to change.
In the Latches to write section, at the bottom of the window,
the values to be written to each register are displayed. If the
background on the text box is green, then the value displayed is
different to the value actually on the device. Click Write x Latch
to write that value to the device.
Under the File menu, the current settings can be saved to, and
loaded from, a text file.
Use the REF IN Frequency text box to set the correct reference
frequency and the reference frequency divider. The reference
TCXO on the evaluation board runs at 10 MHz.
In the Sweep and hop tab, the user can make the device sweep a
range of frequencies, or hop between two set frequencies.
The F2, F3, and F4 keys switch between the three tabs. F12
increases the output frequency by one channel spacing and
write it to the device. F11 decreases the output frequency by
one channel spacing.
Rev. B | Page 6 of 12
UG-098
08882-008
Evaluation Board User Guide
Figure 8. Software Front Panel Display
Rev. B | Page 7 of 12
UG-098
Evaluation Board User Guide
EVALUATION BOARD SCHEMATIC
08882-009
Figure 9. EV-ADF4360-3EB1Z Schematic
Rev. B | Page 8 of 12
Evaluation Board User Guide
UG-098
08882-010
Figure 10. EV-ADF4360-3EB1Z Schematic (Continued)
Rev. B | Page 9 of 12
UG-098
Evaluation Board User Guide
08882-011
Figure 11. EV-ADF4360-3EB1Z Schematic (Continued)
Rev. B | Page 10 of 12
Evaluation Board User Guide
UG-098
ORDERING INFORMATION
BILL OF MATERIALS
Table 1.
Reference Designator
C1, C3, C5, C29, C30, C32,
C37, C38, C39, C40, C41,
C42, C43
C2, C4, C6, C8
C7
C9, C10, C27
C11, C12, C21, C24
C13
C14
C15
C16
C17, C19
C18, C28
C20, C23
C22, C25
C26
C31, C33
C34
C35, C36
D1
D2
D3
Part Description
Capacitor, 0402, 0.1 μF, 16 V
Manufacturer/Part No.
Kemet C0402C104K4RAC
Capacitor, 0402, 10 pF, 50 V
Capacitor, Case A, 22 μF, 6.3 V
Capacitor, 0603, 1 nF, 50 V
Capacitor, 0402, 10 nF, 16 V
Capacitor, loop filter, 0603, 1 nF, 50 V
Capacitor, loop filter, 0603, 12 nF, 50 V
Capacitor, loop filter, 0603, 390 pF, 50 V
Multilayer ceramic capacitor, 50 V, X7R, 1 nF, ±10%, 0402
Capacitor, 0603, 10 pF, 50 V
Capacitor, 0603, 1 μF, 25 V
Capacitor, Case A, 1 μF, 16 V
Capacitor, Case A, 4.7 μF, 10 V
Capacitor, Case A, 10 μF, 6.3 V
Capacitor, 0805, 10 μF, 6.3 V
Capacitor, 0402, 22 pF, 50 V NPO
Capacitor, 0402, 12 pF, 50 V
LED, SMD red
Diode, 1 A, 50 V
Schottky diode, 20 V
D4
J1, J2
J3 to J6
J7
L1, L2
L3, L4, L5, L6
LK1, LK2
LED, SMD red
Jack SMA end launch tab
Jack SMA end launch tab (not inserted)
USB mini-B
Ceramic chip inductor, 0402 (not inserted)
Ceramic chip inductor, 2.2 nH, 5%, 0402
Header, 1-row, 2-way and jumper socket black
Kemet C0402C100J5GACTU
AVX TAJA226K006R
AVX 06035A102JAT2A
Yageo (Phycomp) CC0402ZRY5V7BB103
Phycomp 2238 861 15102
Phycomp 2238 910 15637
Phycomp 2238 861 15391
Murata GRM155R71H102KA01D
AVX 06035A100JAT2A
Taiyo Yuden TMK107BJ105KA-T
AVX TAJA105K016R
AVX TPSA475K010R1400
Kemet T491A106M016AT
Murata GRM21BR71A106KE51L
Kemet C0402C220J5GACTU
Kemet C0402C120J5GACTU
Avago HSMS-C170
Multicomp 1N4001
Micro Commercial Components, Inc.,
SD103C-TP
Avago HSMS-C170
Johnson Components 142-0701-851
P1
R1 to R4, R13, R22 to R24,
R27, R36, R38
R5
R6, R15
R7, R8, R12, R28, R29, R30
R9
R10
R11
R14, R16
R17 to R19
R20, R21
R25, R26
R31, R32
R34
R35
Battery clip, PCB mounting
Resistor, 0603, 0 Ω
Coilcraft 0603CS-2N2X_LU
Harwin Plc M20-9990245 and
Harwin Plc M7567-05
Keystone Electronics Corp. 593+594
Multicomp MC 0.063W 0603 0R
Resistor, 0603, 51 Ω
Resistor, 0603, 4.7 kΩ
Resistor, 0603, 10 kΩ
Resistor, 0603, 100 Ω
Resistor, loop filter, 0805, 6.8 kΩ
Resistor, loop filter, 0805, 3.9 kΩ
Resistor, 0603, 330 kΩ
Resistor, 0603, 330 Ω
Resistor, 0603, 2.2 kΩ
Resistor, 0603, 470 Ω
Resistor, 0603, 100 kΩ
Resistor, 0603, 140 kΩ
Resistor, 0603, 78.7 kΩ
Multicomp MC 0.063W 0603 1% 51R
Multicomp MC 0.063W 0603 1% 4K7
Multicomp MC 0.063W 0603 1% 10K
Multicomp MC 0.063W 0603 1% 100R
Multicomp MC 0.1W 0805 1% 6K8
Multicomp MC 0.1W 0805 1% 3K9
Multicomp MC 0.063W 0603 1% 330K
Multicomp MC 0.063W 0603 1% 330R
Multicomp MC 0.063W 0603 1% 2K2
Multicomp MC 0.063W 0603 1% 470R
Multicomp MC 0.063W 0603 1% 100K
Multicomp MC 0.063W 0603 1% 140K
Multicomp MC 0.063W 0603 1% 78K7
Rev. B | Page 11 of 12
Molex 56579-0576
UG-098
Reference Designator
SW1
T1 to T8, T13 to T16
T9 to T12
U1
U2
U3
U4
U5
U6
Y1
Evaluation Board User Guide
Part Description
Switch, PCB SPDT
Terminal, PCB, red, PK100
Test point (not inserted)
Integrated integer-N synthesizer
High accuracy low dropout linear 5 V regulator
High accuracy low dropout linear 3 V regulator
ADP3334 Adjustable LDO regulator
IC Serial EEPROM 8-SOIC
USB Microcontroller
10 MHz TCXO (FOX801)
Manufacturer/Part No.
APEM TL36P0050
Vero Technologies, Ltd. 20-313137
Analog Devices, ADF4360-3BCPZ
Analog Devices, ADP3300ARTZ-3
Analog Devices, ADP3300ARTZ-3
Analog Devices, ADP3334ARMZ
Microchip 24LC64-ISN
Cypress CY7C68013A-56LFXC
Fox Electronics FOX801-BELF
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2010–2012 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG08882-0-3/12(B)
Rev. B | Page 12 of 12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement