- No category
advertisement
AJCQ08ACF
Premium, Deluxe and Value Model
Wall Case Dimensions (in inches)
GE ® ENERGY STAR ® 115 Volt Built-in Cool-Only Room Air Conditioner
Wall Case Dimensions and Installation Information (in inches)
Note: When installing slide-out chassis units in through-the-wall applications, keep louvers free. Do not restrict air flow areas.
15-5/8
For answers to your Monogram, ® GE Profile ™ or
GE ® appliance questions, visit our website at geappliances.com or call GE Answer Center ® service, 800.626.2000.
21-13/16
16-7/8
26
Parallel
115V
15 Amp
Note: When installing units in through-the-wall applications.
Do not restrict air flow areas.
AJCQ12DCD
Total volume and shelf area are calculated by the Association of Home
Appliance Manufacturers’ standards.
Listed by
Underwriters
Laboratories
Specification Revised 7/14
Built-in RAC Installation
(Pub. 1-G003 pg. 138) April 30.1993
Built-In Room Air Conditioners
Wall Opening for RAB36/37/38 Case
A finished opening of 26-1/8" x 15-3/4", clear of intrusions, is required. Keep clearance of 4" from side walls. Brick veneer or frame walls should have wood studding surrounding case to provide firm anchoring with screws. Case can be fastened directly to brick or block walls with screws sunk in lead expansion shields.
Make frame if desired or caulk between case and siding
26-1/8
15-3/4
Frame Construction
Lintel
15-3/4
26-1/8
AJCQ08ACF
GE ® ENERGY STAR ® 115 Volt Built-in Cool-Only Room Air Conditioner
Dimensions (in inches)
Installation Information: A finished opening of 26-1/8" x
15-3/4" clear of intrusions is required. Keep clearance of
Make frame if desired or caulk between case and siding
A finished opening of 26-1/8" x 15-3/4", clear of side walls. Brick veneer or frame walls should have wood studding surrounding case to provide firm to the building exterior to assure building integrity.
anchoring with screws. Case can be fastened directly to brick or block walls with screws sunk in lead expansion shields.
RAB48 – includes wall case, exterior grille, steel closure panel and two layers of insulation.
Standard Wall Case RAB46
Solid-sided wall case fabricated of galvanized steel with baked enamel finish. Welded areas are coated with a sealing compound to help resist rust and corrosion.
Polymer gasket surrounds opening to assure tight weather seal. Aluminum grille (RAG13) is included. Panels on interior and between case and grille provide weather protection prior to installation of chassis. Provide firm anchoring with screws.
Case can be fastened directly to brick or block walls with screws sunk in lead expansion shields.
26-1/8
15-3/4
26-1/8
15-3/4
Lintel
OUTSIDE
16-7/8
Fill open cells with mortar or insulation
Plaster Line
Trim Molding
(if desired)
INSIDE
Caulking
Drip Rail
Flexible Mounting Position
For answers to your Monogram, ® GE Profile ™ or
GE ® appliance questions, visit our website at geappliances.com or call GE Answer Center ® service, 800.626.2000.
Brick Block and Brick
Frame Construction
Trim Molding
(if desired)
Total volume and shelf area are calculated by the Association of Home
Appliance Manufacturers’ standards.
Listed by
Underwriters
Laboratories
Specification Revised 7/14
AJCQ08ACF
GE ® ENERGY STAR ® 115 Volt Built-in Cool-Only Room Air Conditioner
Features and Benefits
• 8,200 Cooling BTU
• 9.8 EER, 9.6 CEER
• 115 Volts
• ENERGY STAR ® qualified
• R-410A refrigerant
• Electronic controls with remote
• Electronic digital thermostat control
• Filter reset
• Four-way air direction
• Up-front, washable air filter
• 3 cool / 3 fan speeds
• Model AJCQ08ACF – Soft Gray
AJCQ12DCF
On
Specification Revised 7/14
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project