McLean Cooling Technology | Genesis M28-0416-GXXX | Instruction manual | McLean Cooling Technology Genesis M28-0416-GXXX Instruction manual

GENESIS™
Air Conditioners
All Models
INSTRUCTION MANUAL
Rev. G
© 2015 Pentair Equipment Protection
P/N 89104462
89104462
TABLE OF CONTENTS
RECEIVING THE AIR CONDITIONER................................................................................................................................................................................3
HANDLING AND TESTING THE AIR CONDITIONER.......................................................................................................................................................3
INSTALLATION INSTRUCTIONS......................................................................................................................................................................................4
M13 Design Data.....................................................................................................................................................................................................................................5
M13 Dimensional Drawing.....................................................................................................................................................................................................................5
M13 Mounting Gasket and Cutout Dimensions.....................................................................................................................................................................................5
M13 Components List............................................................................................................................................................................................................................6
M13 Schematic and Wire Diagram, 115/230 Volt 1000 BTU................................................................................................................................................................7
M17 Design Data.....................................................................................................................................................................................................................................8
M17 Dimensional Drawing.....................................................................................................................................................................................................................8
M17 Mounting Gasket and Cutout Dimensions.....................................................................................................................................................................................8
M17 Components List............................................................................................................................................................................................................................9
M17 Schematic and Wire Diagram, 115/230 Volt 1800 BTU...............................................................................................................................................................10
M28 Design Data...................................................................................................................................................................................................................................11
M28 Dimensional Drawing...................................................................................................................................................................................................................11
M28 Mounting Gasket and Cutout Dimensions...................................................................................................................................................................................12
M28 Components List..........................................................................................................................................................................................................................13
M28 Schematic and Wire Diagram, 115/230 Volt, 2200 BTU .............................................................................................................................................................14
M28 Schematic and Wire Diagram, 115/230 Volt, 4000 BTU & 230 Volt 6000 BTU............................................................................................................................15
M28 Schematic and Wire Diagram, 115 Volt, 6000 BTU.....................................................................................................................................................................15
M33 Design Data...................................................................................................................................................................................................................................16
M33 Dimensional Drawing...................................................................................................................................................................................................................16
M33 Mounting Gasket and Cutout Dimensions...................................................................................................................................................................................17
M33 Components List..........................................................................................................................................................................................................................18
M33 Wire Diagram and Schematic, 115 V, 4000 BTU..........................................................................................................................................................................19
Wire Diagram, 230 V, 4000 BTU...........................................................................................................................................................................................................19
M36 Design Data...................................................................................................................................................................................................................................20
M36 Dimensional Drawing...................................................................................................................................................................................................................20
M36 Mounting Gasket and Cutout Dimensions...................................................................................................................................................................................21
M36 Components List..........................................................................................................................................................................................................................22
M36 Schematic and Wire Diagram, 115/230 Volt 6000 BTU..............................................................................................................................................................22
M52 Design Data...................................................................................................................................................................................................................................23
M52 Dimensional Drawing...................................................................................................................................................................................................................23
M52 Mounting Gasket and Cutout Dimensions...................................................................................................................................................................................24
M52 Components List..........................................................................................................................................................................................................................25
M52 Schematic and Wire Diagram, 115 Volt 10000 and 12000 BTU...................................................................................................................................................26
M52 Schematic and Wire Diagram, 115/230 Volt 6000/8000 BTU and 230 Volt 10000/12000 BTU...................................................................................................26
MHB11 Design Data.............................................................................................................................................................................................................................27
MHB11 Dimensional Drawing..............................................................................................................................................................................................................27
MHB11 Mounting Gasket and Cutout Dimensions..............................................................................................................................................................................28
MHB11 Components List.....................................................................................................................................................................................................................29
MHB11 Schematic and Wire Diagram, 115 and 230 Volt, 2200 BTU .................................................................................................................................................30
MHB11 Schematic and Wire Diagram, 115/230 Volt, 4000 BTU.........................................................................................................................................................30
TEMPERATURE CONTROL.............................................................................................................................................................................................32
PRINCIPLES OF OPERATION.........................................................................................................................................................................................32
MAINTENANCE..............................................................................................................................................................................................................32
Compressor..........................................................................................................................................................................................................................................32
Inlet Air Filter........................................................................................................................................................................................................................................32
How To Remove, Clean or Install a New Inlet Air Filter......................................................................................................................................................................33
Condenser and Evaporator Air Movers...............................................................................................................................................................................................33
Refrigerant Loss...................................................................................................................................................................................................................................33
TROUBLE SHOOTING.....................................................................................................................................................................................................34
Basic Air Conditioning Trouble Shooting Check List..........................................................................................................................................................................34
Symptoms and Possible Causes:.........................................................................................................................................................................................................35
WARRANTY.....................................................................................................................................................................................................................38
RETURN AND REPAIR POLICY............................................................................................................................................................................................................38
LIMITATION OF LIABILITY....................................................................................................................................................................................................................39
NOTE: Some of the information in this manual may not apply if a special unit was ordered. If
additional drawings for a special unit are necessary, they have been inserted. Contact Pentair
Equipment Protection if further information is required.
-2-
© 2015 Pentair Equipment Protection
89104462
RECEIVING THE AIR CONDITIONER
Inspect the air conditioner. Check for concealed damage that may have occurred during shipment. Look for dents,
scratches, loose assemblies, evidence of oil, etc. Damage evident upon receipt should be noted on the freight bill.
Damage should be brought to the attention of the delivering carrier -- NOT to Pentair Equipment Protection -within 15 days of delivery. Save the carton and packing material and request an inspection. Then file a claim with
the delivering carrier.
Pentair Equipment Protection cannot accept responsibility for freight damages; however, we will assist you in any
way possible.
HANDLING AND TESTING THE AIR CONDITIONER
If the air conditioner has been in a horizontal position, be certain it is placed in an upright, vertical or mounting
position for a minimum of five (5) minutes before operating.
CAUTION
Do not attempt to operate the air conditioner while it is horizontal
or on its side, back or front. The refrigeration compressor is filled
with lubricating oil. This will cause permanent damage to the air
conditioner and also voids the warranty.
TEST FOR FUNCTIONALITY BEFORE MOUNTING THE AIR CONDITIONER TO THE ENCLOSURE.
Refer to the nameplate for proper electrical current requirements, and then connect the power cord to a properly
grounded power supply. Minimum circuit ampacity should be at least 125% of the amperage shown in the design
data section for the appropriate model. No other equipment should be connected to this circuit to prevent
overloading.
Operate the air conditioner for five (5) to ten (10) minutes. No excessive noise or vibration should be evident
during this run period. The condenser blower (ambient air), the evaporator blower (enclosure air), and the
compressor should be running.
Condenser air temperatures should be warmer than normal room temperatures within a few minutes.
The compressor is provided with automatic reset thermal overload protection. This thermo-switch is located
and mounted inside the plastic enclosure clipped to the compressor. The switch operates when the compressor
overheats due to clogged or dirty inlet air filter or if ambient air temperatures exceed nameplate rating or if
enclosure dissipated heat loads exceed the rated capacity of the air conditioner. The thermal overload switch will
actuate and stop compressor operation. The blowers will continue to operate and the compressor will restart
after it has cooled to within the thermal overload cut-in temperature setting.
89104462
© 2015 Pentair Equipment Protection
-3-
INSTALLATION INSTRUCTIONS
1. Inspect air conditioner. Verify functionality before mounting the air conditioner, seeHANDLING
AND TESTING THE AIR CONDITIONER on page 3.
2. Using the cutout dimensions shown in this manual or the cutout template printed on the units
shipping carton, prepare the air “IN” and air “OUT” openings, and mounting bolt hole pattern for
the enclosure.
3. Using the gasket kit provided, install gaskets to air conditioner. See gasket kit illustration in this
manual for proper location.
4. Mount air conditioner on enclosure using mounting bolts and screws provided. “EZ” mount tabs
can be used to hold unit on enclosure while mounting in place. Allow unit to remain upright for a
minimum of five (5) minutes before starting. Caution: Air conditioner must be in upright position
during operation.
5. Refer to top of nameplate for electrical requirements. Connect the power cord to a properly
grounded power supply. Use of an extension cord is not recommended. Electrical circuit should be
fused with slow blow or HACR circuit breaker.
-4-
© 2015 Pentair Equipment Protection
89104462
M13 DESIGN DATA
Model
M13-0116-G1014
Availability
Voltage
Hz
Full Load
Amps
Phase
BTU/Hr. @
Max Ambient
Temperature
Max Ambient
Temperature
(°F/°C)
Shipping
Weight
(lb./kg)
Stock
100/115
50/60
3.7/3.9
1
800/1000
125/52
46/21
100/115
50/60
3.7/3.9
1
800/1000
125/52
46/21
220/230
50/60
2.6/2.6
1
800/1000
125/52
46/21
220/230
50/60
2.6/2.6
1
800/1000
125/52
46/21
M13-0116-G1XXX
M13-0126-G1008
M13-0126-G1XXX
Stock
-XXX will be replaced with a three-digit number designating all desired options. Consult the factory for specific model numbers.
M13 DIMENSIONAL DRAWING
M13 MOUNTING GASKET AND CUTOUT DIMENSIONS
89104462
© 2015 Pentair Equipment Protection
-5-
Mounting gasket kit 17-1000-50 included. Apply
gasket to the back of the air conditioner before
mounting to enclosure.
Dashed lines represent aire conditioner.
M13 COMPONENTS LIST
Part Number
Item
Number.
115 Volt
230 Volt
Fan, Condenser
1
12-1012-01
12-1012-02
Fan, Evaporator
2
13-1015-01
13-1015-02
Coil, Condenser
4
13-1001-05
13-1001-05
Coil, Evaporator
5
13-1001-04
13-1001-04
Compressor, AE
6
89109065
89109066
Control Panel Assembly, Narrow
N/S
10-1106-100
10-1106-100
Filter, Air, Reusable, Narrow
N/S
10-1000-57
10-1000-57
Part Description
Filter/Dryer
7
52-6028-00
52-6028-00
N/S
10-1130-01
10-1130-01
Pan, Condensate
9
10-1130-12
10-1130-12
Pan, Evaporator
10
10-1130-13
10-1130-13
Relay, Compressor, Start
11
89117321
89117322
Service Cord
12
52-6035-138
52-6035-139
Terminal Block
13
10-1003-03
10-1003-03
Thermal Overload, Compressor
14
89117325
89117326
Thermostat, SPST, 55-100F
15
10-1061-16
10-1061-16
Transformer, 10 VAC Secondary
16
10-1006-114
10-1006-115
Grille, Front, Narrow
-6-
© 2015 Pentair Equipment Protection
89104462
M13 SCHEMATIC AND WIRE DIAGRAM, 115/230 VOLT 1000 BTU
89104462
© 2015 Pentair Equipment Protection
-7-
M17 DESIGN DATA
Model
M17-0216-G009
Availability
Voltage
Hz
Full Load
Amps
Phase
BTU/Hr. @
Max Ambient
Temperature
Max Ambient
Temperature
(°F/°C)
Shipping
Weight
(lb./kg)
Stock
100/115
50/60
7.2/6.9
1
1500/1800
125/52
56/25
100/115
50/60
7.2/6.9
1
1500/1800
125/52
56/25
220/230
50/60
3.1/3.1
1
1500/1800
125/52
56/25
220/230
50/60
3.1/3.1
1
1500/1800
125/52
56/25
M17-0216-GXXX
M17-0226-G004
M17-0226-GXXX
Stock
-XXX will be replaced with a three-digit number designating all desired options. Consult the factory for specific model numbers.
M17 DIMENSIONAL DRAWING
M17 MOUNTING GASKET AND CUTOUT DIMENSIONS
-8-
© 2015 Pentair Equipment Protection
89104462
Mounting gasket kit 17-1000-50 included. Apply
gasket to the back of the air conditioner before
mounting to enclosure.
Dashed lines represent aire conditioner.
M17 COMPONENTS LIST
Part Number
Item
Number.
115 Volt
230 Volt
Fan, Condenser
1
12-1012-01
12-1012-02
Fan, Evaporator
2
12-1012-01
12-1012-02
Capacitor, Compressor, Start
3
89116454
89117017
Coil, Condenser
4
17-1001-00
17-1001-00
Coil, Evaporator
5
17-1002-01
17-1002-01
Compressor, AE
6
89108747
89108748
Control Panel Assembly, Narrow
N/S
10-1106-100
10-1106-100
Filter, Air, Reusable, Narrow
N/S
10-1000-57
10-1000-57
7
52-6028-03
52-6028-03
N/S
10-1130-01
10-1130-01
Pan, Condensate
9
10-1130-14
10-1130-14
Pan, Evaporator
10
10-1130-18
10-1130-18
Relay, Compressor, Start
11
89117323
89117324
Service Cord
12
52-6035-138
52-6035-139
Terminal Block
13
10-1003-03
10-1003-03
Thermal Overload, Compressor
14
89117327
89117328
Thermostat, SPST, 55-100F
15
10-1061-16
10-1061-16
Transformer, 10 VAC Secondary
16
10-1006-114
10-1006-115
Part Description
Filter/Dryer
Grille, Front, Narrow
89104462
© 2015 Pentair Equipment Protection
-9-
M17 SCHEMATIC AND WIRE DIAGRAM, 115/230 VOLT 1800 BTU
- 10 -
© 2015 Pentair Equipment Protection
89104462
M28 DESIGN DATA
Voltage
Hz
Full Load
Amps
Phase
BTU/Hr. @
Max Ambient
Temperature
Max Ambient
Temperature
(°F/°C)
Shipping
Weight
(lb./kg)
100/115
50/60
8.3/8.4
1
2200/2200
125/52
97/44
100/115
50/60
8.3/8.4
1
2200/2200
125/52
97/44
220/230
50/60
4.2/4.2
1
2200/2200
125/52
97/44
220/230
50/60
4.2/4.2
1
2200/2200
125/52
97/44
115
50/60
14.6/14.0
1
3800/4000
125/52
116/53
115
50/60
14.6/14.0
1
3800/4000
125/52
116/53
230
50/60
7.4/6.9
1
3800/4000
125/52
116/53
M28-0426-GXXX
230
50/60
7.4/6.9
1
3800/4000
125/52
116/53
M28-0616-GXXX
115
50/60
16.4/17.2
1
5400/6000
125/52
120/55
M28-0626-GXXX
230
50/60
8.0
1
5400/6000
125/52
120/55
Model
M28-0216-G013
Availability
STOCK
M28-0216-GXXX
M28-0226-G004
STOCK
M28-0226-GXXX
M28-0416-G007
STOCK
M28-0416-GXXX
M28-0426-G032
STOCK
-XXX will be replaced with a three-digit number designating all desired options. Consult the factory for specific model numbers.
M28 DIMENSIONAL DRAWING
89104462
© 2015 Pentair Equipment Protection
- 11 -
M28 MOUNTING GASKET AND CUTOUT DIMENSIONS
(3.)
Mounting gasket kit 28-1000-50 included. Apply
gasket to the back of the air conditioner before
mounting to enclosure.
- 12 -
1.Dashed lines represent air conditioner.
2.Cutout dimensions are for standard unit.
3.Hole may be deleted if service cord is routed through 3.00
x 13.50 cutout (except on units with electric heat).
© 2015 Pentair Equipment Protection
89104462
M28 COMPONENTS LIST
Part Number (115 Volt)
Item
Number.
2200 BTU
4000 BTU
6000 BTU
Blower, Condenser
1
30-4019-01M
30-4019-01M
38-2019-04
Blower, Evaporator
2
28-1064-06M
28-1064-06M
28-1064-06M
Capacitor, Compressor, Start/Run
3
89116454
10-1032-13
10-1032-15
Coil, Condenser
4
24-1001-00
24-1001-00
24-1001-00
Coil, Evaporator
5
28-1001-00
28-1001-01
14-1002-00
Part Description
Compressor, AE/AK/AK
6
89098747
10-1016-26
10-1016-68
Control Panel Assembly, Wide
N/S
10-1106-101
10-1106-101
10-1106-101
Filter, Air, Reusable, Wide
N/S
10-1000-56
10-1000-56
10-1000-56
7
52-6028-00
52-6028-00
52-6028-00
Filter/Dryer
Grille, Front, Wide
N/S
10-1130-00
10-1130-00
10-1130-00
Hot Gas By-Pass Valve
8
N/A
52-6027-16
52-6027-11
Pan, Condensate
9
10-1130-17
10-1130-17
10-1130-17
Pan, Evaporator
10
10-1130-15
10-1130-15
10-1130-15
Relay, Compressor, Start
11
89117323
10-1028-14
N/A
Service Cord
12
52-6035-138
52-6035-142
52-6035-125
Terminal Block (If Installed)
13
10-1003-31
10-1003-31
10-1003-31
Thermal Overload, Compressor
14
89117327
10-1007-45
10-1007-50
Thermostat, SPST, 55-100F
15
10-1061-16
10-1061-16
10-1061-16
Transformer, 10 VAC Secondary
16
10-1006-114
10-1006-114
10-1006-114
Part Number (230 Volt)
Item
Number
2200 BTU
4000 BTU
6000 BTU
Blower, Condenser
1
30-4019-02M
30-4019-02M
38-2020-04
Blower, Evaporator
2
28-1064-05M
28-1064-05M
28-1064-05M
Capacitor, Compressor., Start/Run
3
89117017
10-1032-14
10-1032-18
Coil, Condenser
4
24-1001-00
24-1001-00
24-1001-00
Coil, Evaporator
5
28-1001-00
28-1001-01
14-1002-00
Compressor, AE/AK/AK
6
89108748
10-1026-77
10-1026-80
Control Panel Assembly, Wide
N/S
10-1106-101
10-1106-101
10-1106-101
Filter, Air, Reusable, Wide
N/S
10-1000-56
10-1000-56
10-1000-56
7
52-6028-00
52-6028-00
52-6028-00
N/S
10-1130-00
10-1130-00
10-1130-00
Part Description
Filter/Dryer
Grille, Front, Wide
Hot Gas By-Pass Valve
8
N/A
52-6027-16
52-6027-11
Pan, Condensate
9
10-1130-17
10-1130-17
10-1130-17
Pan, Evaporator
10
10-1130-15
10-1130-15
10-1130-15
Relay, Compressor, Start
11
89117324
10-1028-15
N/A
Service Cord
12
52-6035-139
52-6035-139
52-6035-139
Terminal Block (If Installed)
13
10-1003-31
10-1003-31
10-1003-31
Thermal Overload, Compressor
14
89117328
10-1007-51
10-1007-49
Thermostat, SPST, 55-100F
15
10-1061-16
10-1061-16
10-1061-16
Transformer, 10 VAC Secondary
16
10-1006-115
10-1006-115
10-1006-115
89104462
© 2015 Pentair Equipment Protection
- 13 -
M28 SCHEMATIC AND WIRE DIAGRAM, 115/230 VOLT, 2200 BTU
- 14 -
© 2015 Pentair Equipment Protection
89104462
M28 SCHEMATIC AND WIRE DIAGRAM, 115/230 VOLT, 4000 BTU & 230 VOLT 6000 BTU
M28 SCHEMATIC AND WIRE DIAGRAM, 115 VOLT, 6000 BTU
89104462
© 2015 Pentair Equipment Protection
- 15 -
M33 DESIGN DATA
Model
M33-0416-G010
Availability
Stock
M33-0416-GXXX
M33-0426-G009
M33-0426-GXXX
Stock
Voltage
Hz
Full Load
Amps
Phase
BTU/Hr. @
Max Ambient
Temperature
Max Ambient
Temperature
(°F/°C)
Shipping
Weight
(lb./kg)
115
50/60
11.6/10.8
1
3700/4000
131/55
105/48
115
50/60
11.6/10.8
1
3700/4000
131/55
105/48
230
50/60
7.2/7.3
1
3700/4000
131/55
105/48
230
50/60
7.2/7.3
1
3700/4000
131/55
105/48
-XXX will be replaced with a three-digit number designating all desired options. Consult the factory for specific model numbers.
M33 DIMENSIONAL DRAWING
- 16 -
© 2015 Pentair Equipment Protection
89104462
M33 MOUNTING GASKET AND CUTOUT DIMENSIONS
Mounting gasket kit 33-1000-50 included. Apply
gasket to the back of the air conditioner before
mounting to enclosure.
89104462
1.Dashed lines represent aire conditioner.
2.Cutout dimensions for standard unit.
3.Service cord to be routed through 2.00 x 11.12 cutout.
4.Bottom cutout will accomodate air conditioner or heat
exchanger.
© 2015 Pentair Equipment Protection
- 17 -
M33 COMPONENTS LIST
Part Number (4000 BTU)
Item
Number
115 Volt
230 Volt
Blower, Condenser, Top Discharge
1
38-2019-04
38-2020-04
Blower, Condenser, Front Discharge
1
38-2019-00
38-2020-00
Fan, Evaporator
2
12-1012-01
12-1012-02
Capacitor, Compressor, Run
3
N/A
89100497
Capacitor, Compressor, Start
4
N/A
89100496
Coil, Condenser
5
33-2001-01
33-2001-01
Coil, Evaporator
6
33-2002-02
33-2002-02
Control Panel Assembly, Narrow
N/S
10-1106-100
10-1106-100
Filter, Air, Reusable, Narrow
N/S
10-1000-57
10-1000-57
Part Description
Compressor, AK
7
89100365
89104088
N/S
10-1130-01
10-1130-01
8
52-6028-00
52-6028-00
Hot Gas By-Pass Valve
9
52-6027-16
52-6027-16
Pan, Condensate
10
10-1130-17
10-1130-17
Pan, Evaporator
11
10-1130-16
10-1130-16
Relay, Compressor, Start
12
N/A
89100495
Service Cord
13
52-6035-143
52-6035-141
Terminal Block (if installed)
14
10-1003-03
10-1003-03
Thermal Overload, Compressor
15
10-1007-45
10-1007-51
Thermostat, SPST, 55-100F
16
10-1061-16
10-1061-16
Transformer, 10 VAC Secondary
17
10-1006-114
10-1006-115
Grille, Front, Narrow
Filter/Dryer
- 18 -
© 2015 Pentair Equipment Protection
89104462
M33 WIRE DIAGRAM AND SCHEMATIC, 115 V, 4000 BTU
89100994
WIRE DIAGRAM, 230 V, 4000 BTU
89104462
© 2015 Pentair Equipment Protection
- 19 -
M36 DESIGN DATA
Model
M36-0616-G307
Availability
Stock
M36-0616-GXXX
M36-0626-G306
M36-0626-GXXX
Stock
Voltage
Hz
Full Load
Amps
Phase
BTU/Hr. @
Max Ambient
Temperature
Max Ambient
Temperature
(°F/°C)
Shipping
Weight
(lb./kg)
115
50/60
10.0/10.0
1
5000/6000
105/48
115
50/60
10.0/10.0
1
5000/6000
105/48
230
50/60
5.0/5.0
1
5000/6000
105/48
230
50/60
5.0/5.0
1
5000/6000
105/48
-XXX will be replaced with a three-digit number designating all desired options. Consult the factory for specific model numbers.
M36 DIMENSIONAL DRAWING
- 20 -
© 2015 Pentair Equipment Protection
89104462
M36 MOUNTING GASKET AND CUTOUT DIMENSIONS
Mounting gasket kit 36-1000-50 included. Apply
gasket to the back of the air conditioner before
mounting to enclosure.
89104462
1.Dashed lines represent aire conditioner.
2.Cutout dimensions for standard unit.
3.Service cord to be routed through 3.00 x 14.00 cutout.
© 2015 Pentair Equipment Protection
- 21 -
M36 COMPONENTS LIST
Part Number (6000 BTU)
Item
Number
115 Volt
230 Volt
Blower, Condenser
1
38-2019-04
38-2020-04
Blower, Evaporator
2
28-1064-06M
28-1064-05M
Capacitor, Compressor, Run
3
52-6032-06
S-6173
Coil, Condenser
4
36-1017-01
36-1017-01
Coil, Evaporator
5
28-1001-01
28-1001-01
Part Description
Compressor, Rotary
6
10-1016-91
10-1026-123
Control Panel Assembly, Wide
N/S
10-1106-101
10-1106-101
Filter, Air, Reusable, Wide
N/S
10-1000-56
10-1000-56
7
52-6028-00
52-6028-00
Grille, Front, Wide
N/S
10-1130-00
10-1130-00
Pan, Condensate
9
10-1130-17
10-1130-17
Pan, Evaporator
10
10-1130-19
10-1130-19
Relay, Compressor (optional)
N/S
10-1042-06
10-1042-13
Start Capacitor, Compressor (optional)
N/S
10-1032-08
10-1032-08
Time Delay Relay (optional)
N/S
10-1005-71
N/A
Contactor (optional)
N/S
10-1005-41
N/A
Service Cord
12
52-6035-143
52-6035-141
Thermal Overload, Compressor
14
10-1007-18
MRA5742-114
Thermostat, SPST, 55-100F
15
10-1061-16
10-1061-16
Transformer, 10 VAC Secondary
16
10-1006-114
10-1006-115
Filter/Dryer
M36 SCHEMATIC AND WIRE DIAGRAM, 115/230 VOLT 6000 BTU
- 22 -
© 2015 Pentair Equipment Protection
89104462
M52 DESIGN DATA
Voltage
Hz
Full Load
Amps
Phase
BTU/Hr. @
Max Ambient
Temperature
Max Ambient
Temperature
(°F/°C)
Shipping
Weight
(lb./kg)
M28-0626-GXXX
115
50/60
13.0/13.0
1
5000/6000
125/52
155/70
M52-0626-XXX
230
50/60
6.5/6.5
1
5000/6000
125/52
155/70
115
50/60
14.5/14.5
1
6700/8000
125/52
160/73
115
50/60
14.5/14.5
1
6700/8000
125/52
160/73
230
50/60
8.0/8.0
1
6700/8000
125/52
160/73
230
50/60
8.0/8.0
1
6700/8000
125/52
160/73
110/115
50/60
18.9/19.5
1
8300/10000
125/52
165/75
110/115
50/60
18.9/19.5
1
8300/10000
125/52
165/75
220/230
50/60
9.5/9.8
1
8300/10000
125/52
165/75
220/230
50/60
9.5/9.8
1
8300/10000
125/52
165/75
110/115
50/60
24.0/23.0
1
10000/12000*
125/52
175/79
110/115
50/60
24.0/23.0
1
10000/12000*
125/52
175/79
220/230
50/60
12.2/11.6
1
10000/12000*
125/52
175/79
220/230
50/60
12.2/11.6
1
10000/12000*
125/52
175/79
Model
M52-0816-032
Availability
Stock
M52-0816-XXX
M52-0826-015
Stock
M52-0826-XXX
M52-1016-038
Stock
M52-1016-XXX
M52-1026-021
Stock
M52-1026-XXX
M52-1216-017
Stock
M52-1216-XXX
M52-1226-034
M52-1226-XXX
Stock
-XXX will be replaced with a three-digit number designating all desired options. Consult the factory for specific model numbers.
* Based on return air temperature slightly above ambient.
M52 DIMENSIONAL DRAWING
89104462
© 2015 Pentair Equipment Protection
- 23 -
M52 MOUNTING GASKET AND CUTOUT DIMENSIONS
Mounting gasket kit 52-1000-50 included. Apply
gasket to the back of the air conditioner before
mounting to enclosure.
- 24 -
1.Dashed lines represent air conditioner.
2.Cutout dimensions for standard unit.
3.Hole may be deleted if service cord is routed through 4.50
x 15.63 cutout (except on units with electric heat).
© 2015 Pentair Equipment Protection
89104462
M52 COMPONENTS LIST
Part Number (115 Volt)
Item
Number
6000 BTU
8000 BTU
10000 BTU
12000 BTU
Blower, Condenser
1
52-6034-10
52-6034-10
52-6034-10
52-6034-10
Blower, Evaporator
2
52-6075-00
52-6075-00
52-6075-00
52-6034-10
Capacitor, Compressor, Run
3
52-6031-01
52-6032-01
52-6032-01
52-6032-01
Coil, Condenser
4
52-6111-00
52-6111-00
52-6111-00
52-6111-03
Coil, Evaporator
5
28-1001-01
52-6002-02
52-6121-01
52-6121-01
Part Description
Compressor, AK
6
10-1016-08
10-1016-10
10-1016-12
10-1016-12
Control Panel Assembly, Wide
N/S
10-1106-101
10-1106-101
10-1106-101
10-1106-101
Filter, Air, Reusable, Wide
N/S
10-1000-56
10-1000-56
10-1000-56
10-1000-56
7
52-6028-00
52-6028-00
52-6028-00
52-6028-00
Filter/Dryer
Grille, Front, Wide
N/S
10-1130-00
10-1130-00
10-1130-00
10-1130-00
Hot Gas By-Pass Valve
8
52-6027-00
52-6027-00
52-6027-00
52-6027-00
Pan, Condensate
9
10-1130-17
10-1130-17
10-1130-17
10-1130-17
Pan, Evaporator
10
10-1130-23
10-1130-23
10-1130-23
10-1130-23
Contactor, Compressor, Start
11
N/A
N/A
10-1005-41
10-1005-41
Contactor Cover, Compressor
11
N/A
N/A
10-1005-68
10-1005-68
Service Cord
12
52-6035-142
52-6035-142
52-6035-125
52-6035-125
Terminal Block
13
10-1003-31
10-1003-31
10-1003-31
10-1003-31
Thermal Overload, Compressor
14
10-1007-03
10-1007-04
10-1007-05
10-1007-05
Thermostat, SPST, 55-100F
15
10-1061-16
10-1061-16
10-1061-16
10-1061-16
Transformer, 10 VAC Secondary
16
10-1006-114
10-1006-114
10-1006-114
10-1006-114
Part Number (230 Volt)
Item
Number
6000 BTU
8000 BTU
10000 BTU
12000 BTU
Blower, Condenser
1
52-6025-10
52-6025-10
52-6025-10
52-6025-10
Blower, Evaporator
2
52-6076-00
52-6076-00
52-6076-00
52-6025-10
Capacitor, Compressor, Run
3
52-6031-01
52-6031-01
52-6031-01
52-6031-01
Coil, Condenser
4
52-6111-00
52-6111-00
52-6111-00
52-6111-03
Coil, Evaporator
5
28-1001-01
52-6002-02
52-6121-01
52-6121-01
Compressor, AK
6
10-1026-08
10-1026-10
10-1026-12
10-1026-12
Control Panel Assembly, Wide
N/S
10-1106-101
10-1106-101
10-1106-101
10-1106-101
Filter, Air, Reusable, Wide
N/S
10-1000-56
10-1000-56
10-1000-56
10-1000-56
7
52-6028-00
52-6028-00
52-6028-00
52-6028-00
N/S
10-1130-00
10-1130-00
10-1130-00
10-1130-00
8
52-6027-00
52-6027-00
52-6027-00
52-6027-00
Pan, Condensate
9
10-1130-17
10-1130-17
10-1130-17
10-1130-17
Pan, Evaporator
10
10-1130-23
10-1130-23
10-1130-23
10-1130-23
Relay, Compressor
11
N/A
N/A
N/A
N/A
Service Cord
12
52-6035-139
52-6035-139
52-6035-139
52-6035-141
Terminal Block
13
10-1003-31
10-1003-31
10-1003-31
10-1003-31
Thermal Overload, Compressor
14
10-1007-11
10-1007-12
10-1007-13
10-1007-13
Thermostat, SPST, 55-100F
15
10-1061-16
10-1061-16
10-1061-16
10-1061-16
Transformer, 10 VAC Secondary
16
10-1006-115
10-1006-115
10-1006-115
10-1006-115
Part Description
Filter/Dryer
Grille, Front, Wide
Hot Gas By-Pass Valve
89104462
© 2015 Pentair Equipment Protection
- 25 -
M52 SCHEMATIC AND WIRE DIAGRAM, 115 VOLT 10000 AND 12000 BTU
M52 SCHEMATIC AND WIRE DIAGRAM, 115/230 VOLT 6000/8000 BTU AND 230 VOLT
10000/12000 BTU
- 26 -
© 2015 Pentair Equipment Protection
89104462
MHB11 DESIGN DATA
Model
MHB11-0216-G306
Availability
STOCK
MHB11-0216-G3XX
MHB11-0226-G306
STOCK
MHB11-0226-G3XX
MHB11-0416-G307
STOCK
MHB11-0416-G3XX
MHB11-0426-G306
MHB11-0426-G3XX
STOCK
Voltage
Hz
Full Load
Amps
Phase
BTU/Hr. @
Max Ambient
Temperature
Max Ambient
Temperature
(°F/°C)
Shipping
Weight
(lb./kg)
115
50/60
9.6/8.4
1
2200/2400
125/52
90/41
115
50/60
9.6/8.4
1
2200/2400
125/52
90/41
230
50/60
4.3/4.2
1
2100/2400
125/52
90/41
230
50/60
4.3/4.2
1
2100/2400
125/52
90/41
110/115
50/60
14.7/13.6
1
3300/4000
125/52
108/49
110/115
50/60
14.7/13.6
1
3300/4000
125/52
108/49
220/230
50/60
8.0/7.5
1
3300/4000
125/52
108/49
220/230
50/60
8.0/7.5
1
3300/4000
125/52
108/49
-XXX will be replaced with a three-digit number designating all desired options. Consult the factory for specific model numbers.
MHB11 DIMENSIONAL DRAWING
89104462
© 2015 Pentair Equipment Protection
- 27 -
MHB11 MOUNTING GASKET AND CUTOUT DIMENSIONS
Mounting gasket kit 11-1000-50 included. Apply
gasket to the bottom of the air conditioner before
mounting to enclosure.
- 28 -
1.Dashed lines represent air conditioner.
2.Cutout dimensions are for standard unit.
© 2015 Pentair Equipment Protection
89104462
MHB11 COMPONENTS LIST
Part Number (115 Volt)
Part Number (230 Volt)
Item
Number
2200 BTU
4000 BTU
2200 BTU
4000 BTU
Blower, Condenser
1
28-1064-06M
28-1064-06M
28-1064-05M
28-1064-05M
Blower, Evaporator
2
28-1064-06M
28-1064-06M
28-1064-05M
28-1064-05M
Capacitor, Compressor, Start
3
N/A
10-1032-13
N/A
10-1032-14
Coil, Condenser
4
11-3001-03
11-3001-03
11-3001-03
11-3001-03
Coil, Evaporator
5
11-1002-00
11-1002-00
11-1002-00
11-1002-00
Part Description
Compressor, AE/AK/AE/AK
6
29747
10-1016-26
29748
10-1026-77
Control Panel Assembly, Wide
N/S
10-1106-101
10-1106-101
10-1106-101
10-1106-101
Filter, Air, Reusable, Wide
N/S
10-1000-56
10-1000-56
10-1000-56
10-1000-56
7
52-6028-00
52-6028-00
52-6028-00
52-6028-00
Filter/Dryer
Grille, Front, Wide
N/S
10-1130-00
10-1130-00
10-1130-00
10-1130-00
Hot Gas By-Pass Valve
8
52-6027-16
52-6027-16
52-6027-16
52-6027-16
Pan, Condensate
9
10-1130-24
10-1130-24
10-1130-24
10-1130-24
Pan, Evaporator
10
10-1130-11
10-1130-11
10-1130-11
10-1130-11
Relay, Compressor, Start
11
N/A
10-1028-14
N/A
10-1028-15
Service Cord
12
52-6035-140
52-6035-143
52-6035-141
52-6035-141
Terminal Block
13
10-1003-31
10-1003-31
10-1003-31
10-1003-31
Thermal Overload, Compressor
14
N/A
10-1007-45
N/A
10-1007-51
Thermostat, SPST, 55-100F
15
10-1061-16
10-1061-16
10-1061-16
10-1061-16
Transformer, 10 VAC Secondary
16
10-1006-114
10-1006-114
10-1006-115
10-1006-115
89104462
© 2015 Pentair Equipment Protection
- 29 -
MHB11 SCHEMATIC AND WIRE DIAGRAM, 115 AND 230 VOLT, 2200 BTU
04-2001-009 Rev D
05-2001-004 Rev A
MHB11 SCHEMATIC AND WIRE DIAGRAM, 115/230 VOLT, 4000 BTU
- 30 -
© 2015 Pentair Equipment Protection
89104462
NOTES
89104462
© 2015 Pentair Equipment Protection
- 31 -
TEMPERATURE CONTROL
The electromechanical thermostat is factory preset to 75°F/23°C. To change the temperature setting, remove the
front cover and screen. Use a standard screwdriver to adjust thermostat. For cooler temperatures turn clockwise,
for warmer temperatures turn counterclockwise.
PRINCIPLES OF OPERATION
If electrical power to the air conditioner is interrupted and reapplied immediately, (within 3 to 5 seconds), the
compressor may not restart due to the high back pressure of the compressor. It takes a minimum of one (1)
minute after shut-down for the compressor suction and discharge pressures to equalize in order for the air
conditioner to restart.
Operating the air conditioner below the minimum ambient temperature or above the maximum ambient
temperatures indicated on the nameplate voids all warranties.
It is recommended that the warranty section of this manual be read in order to familiarize yourself with
parameters of restricted operation.
The moisture that the enclosure air can contain is limited. If moisture flows from the drain tube continuously this
can only mean that ambient air is entering the enclosure. Be aware that frequent opening of the enclosure’s door
admits humid air, which the air conditioner must then dehumidify.
MAINTENANCE
COMPRESSOR
The compressor requires no maintenance. It is hermetically sealed, properly lubricated at the factory and should
provide years of satisfactory operating service.
Should the refrigerant charge be lost, recharging ports (access fittings) on the suction and discharge sides of the
compressor are provided for recharging and/or checking suction and discharge pressures.
Under no circumstances should the access fitting covers be loosened, removed or tampered with.
Breaking of seals on compressor access fittings during warranty period will void warranty on hermetic system.
Recharging ports are provided for the ease and convenience of reputable refrigeration repair service personnel
for recharging the air conditioner.
INLET AIR FILTER
Proper maintenance of the inlet air filter, located behind the front cover, will assure normal operation of the air
conditioner. If filter maintenance is delayed or ignored, the maximum ambient temperatures under which the unit
is designed to operate will be decreased.
If the compressor’s operating temperature increases above designed conditions due to a dirty or clogged filter
(or plugged condenser coil), the air conditioner’s compressor will stop operating due to actuation of the thermal
overload cutout switch located on the compressor housing. As soon as the compressor temperature has dropped
to within the switch’s cut-in setting, the compressor will restart automatically. However the above condition will
continue to take place until the filter has been cleaned or replaced.
It is recommended that power to the air conditioner be interrupted intentionally when abnormally high
compressor operating temperature causes automatic shutdown of the unit. The above described shutdown
is symptomatic of clogged or dirty filter, thus causing a reduction in cooling airflow across the surface of the
compressor and condenser coil.
Do not run the air conditioner for extended periods of time with the filter removed. Particles of dust, lint, etc., can
plug the fins of the condenser coil which will give the same reaction as a plugged filter. The condenser coil is not
visible through the filter opening, so protect it with a filter.
Continued operation under the above conditions can and will damage and shorten compressor life. The air
conditioner is available with an easily removable inlet filter to facilitate necessary cleaning. There should be no
reason to neglect this necessary maintenance.
- 32 -
© 2015 Pentair Equipment Protection
89104462
HOW TO REMOVE, CLEAN OR INSTALL A NEW INLET AIR FILTER
RP aluminum washable air filters are designed to provide excellent filtering efficiency with a high dust holding
capacity and a minimum amount of resistance to air flow. Because they are constructed entirely of aluminum
they are lightweight and easy to service. Optimum filter performance is maintained by recoating the filters
after washing with RP Super Filter Coat adhesive. To achieve maximum performance from your air handling
equipment, air filters should be cleaned on a regular basis.
The inlet air filter is located behind the front cover. To access filter, pull ring protruding from slot in bottom of
front cover. The filter may now be cleaned or new filter installed.
Cleaning Instructions:
1. Flush the filter with warm water from the exhaust side to the intake side. DO NOT USE CAUSTICS.
2. After flushing, allow filter to drain. Placing it with a corner down will assure complete drainage.
3. Recoat the filters with RP Super Filter Coat adhesive. When spraying filter do so from both sides
for maximum concentration of adhesive.
CONDENSER AND EVAPORATOR AIR MOVERS
Blower and impeller motors require no maintenance. All bearings, shafts, etc. are lubricated during
manufacturing for the life of the motor.
If the condenser blower motor (ambient blower) should fail, it is not necessary to remove the air conditioner from
the cabinet or enclosure to replace the blower. The condenser blower is mounted on its own bulkhead and is
easily accessible by removing the front cover.
CAUTION
Operation of the air conditioner in areas containing airborne
caustics or chemicals can rapidly deteriorate filters, condenser
coils, blowers and motors, etc. Contact Pentair Equipment
Protection for special recommendations.
REFRIGERANT LOSS
Each air conditioner is thoroughly tested prior to leaving the factory to insure against refrigeration leaks. Shipping
damage or microscopic leaks not found with sensitive electronic refrigerant leak detection equipment during
manufacture may require repair or recharging of the system. This work should only be performed by qualified
professionals, generally available through a local, reputable air conditioning repair or service company.
Refer to the data on the nameplate which specifies the type of refrigerant and the charge size in ounces.
Before recharging, make sure there are no leaks and that the system has been properly evacuated into a deep
vacuum.
89104462
© 2015 Pentair Equipment Protection
- 33 -
TROUBLE SHOOTING
BASIC AIR CONDITIONING TROUBLE SHOOTING CHECK LIST
1. Check manufacturer’s nameplate located on the unit for correct power supply.
2. Turn on power to the unit. The evaporator (Enclosure or “COLD” air) blower should come on. Is
there airflow?
YES, proceed to step 3.
NO, possible problem:
•
•
•
Open motor winding
Stuck blower motor
Obstructed blades
Repair or Replace
defective part
3. Check thermostat setting and adjust thermostat to the lowest setting. This should turn on the
condenser blower and compressor. Did condenser blower and compressor come on when the
thermostat was turned on?
YES, proceed to step 4.
NO, possible problem:
•
Defective thermostat
Replace Part
4. Are both blowers and the compressor running? If not the unit will not cool properly.
5. Check condenser (Ambient or “HOT” air) blower for airflow. Is there airflow?
YES, proceed to step 6.
NO, possible problem:
•
•
•
•
Defective thermostat
Open motor winding
Stuck blower motor
Obstructed wheels/blades
Repair or Replace
defective part
6. Carefully check the compressor for operation - motor should cause slight vibration, and the outer
case of the compressor should be warm. Is the compressor showing signs of this?
YES, wait 5 minutes, then proceed to step 7.
NO, possible problem:
•
•
•
•
Defective thermostat
Defective capacitor
Defective overload
Defective relay
Repair or Replace
defective part
7. Make sure the coils are clean. Then check evaporator “air in” and “air out” temperatures. If the
temperatures are the same:
•
•
Possible loss of refrigerant
Possible bad valves in the
compressor
Repair or Replace
defective part
8. To check for a bad thermostat, turn power to the unit off. Remove the control box cover and place
both thermostat wires onto one terminal (replace control box cover for safety). This will activate
the switch in the thermostat. Turn the power on and if both blowers and the compressor come on,
the thermostat needs to be replaced.
- 34 -
© 2015 Pentair Equipment Protection
89104462
SYMPTOMS AND POSSIBLE CAUSES:
SYMPTOM
POSSIBLE CAUSE
Impellers/blowers not running
Unit won’t cool
Compressor not running
Compressor runs, but has bad valves
Loss of refrigerant
Low line voltage at start. Should be +/-10% rated voltage.
Compressor motor stuck
Compressor tries to start but won’t run
Bad contactor
Bad overload switch
Bad run/start capacitor
Unit blows breakers
Undersized breaker/fuse or not time delayed
Short in system
Drain plugged
Getting water in enclosure
Drain tube kinked
Enclosure not sealed (allowing humidity in)
For additional technical information (i.e., amp draw, pressures, temperatures) , contact
Pentair Equipment Protection at 800-896-2665.
89104462
© 2015 Pentair Equipment Protection
- 35 -
NOTES
- 36 -
© 2015 Pentair Equipment Protection
89104462
NOTES
89104462
© 2015 Pentair Equipment Protection
- 37 -
WARRANTY
C.
D.
A.
B.
Pentair Equipment Protection warrants that the Goods manufactured by Pentair Equipment Protection
will be free from defects in material and workmanship for a period of one (1) year from the date of
shipment by Pentair Equipment Protection, subject to the following conditions and exclusions:
Conditions. All Goods must be installed and operated according to the following specifications:
1. Maximum voltage variation no greater than plus or minus 10% of nameplate nominal rating;
2. Maximum frequency variation no greater than plus or minus 3 Hz of nameplate nominal rating;
3. Must not exceed minimum and maximum stated temperatures on the nameplate;
4. Must not exceed (BTU/Hr) rating, including any heat sink as indicated on the nameplate;
5. Refrigerant bearing Goods must not be restarted for a period of one (1) minute after intentional or
accidental shut-off;
6. The filters (if applicable) must be cleaned regularly;
7. The Goods and any parts thereof must not be modified, unless prior written authorization is
received from Pentair Equipment Protection; and
8. All Goods must be installed and grounded in accordance with all relevant electrical and safety
codes, as well as the National Electric Code and OSHA rules and regulations.
9. All Goods must be installed in a stationery application, free of vibration.
A violation of any one of these conditions shall render the warranty hereunder void and of no effect.
Exclusions. This warranty shall be void if product is misapplied in any way or:
1. Buyer specified product is inappropriate for system or environment in which it is operating.
2. Goods are not installed in accordance with Pentair Equipment Protection specifications.
3. Removal or modification of Pentair Equipment Protection label affixed to product without written
Pentair Equipment Protection approval.
Pentair Equipment Protection must be notified of a claim in writing not later than fourteen (14) days from
the date when Buyer has become aware of such occurrence, or where the defect is such that it may cause
damage, immediately, such notice containing a description of how the defect manifests itself. Failure to
provide such prompt notice to Pentair Equipment Protection shall result in forfeiture of Buyer’s rights
under this warranty.
In the event of a warranty claim, Buyer is to return defective goods to Pentair Equipment Protection in
accordance with Pentair Equipment Protection Return Policy. Warranty period for repaired goods remains
at 1 year from shipment of original goods. Pentair Equipment Protection sole obligation to Buyer under
this warranty will be, at Pentair Equipment Protection option:
Repair or replace Pentair Equipment Protection products or parts found to be defective in material or
workmanship.
Issue credit for the purchase price paid by Buyer relating to such defective Goods or part.
THIS WARRANTY CONSTITUTES THE ENTIRE WARRANTY WITH RESPECT TO THE GOODS AND IS IN
LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY AND IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
RETURN AND REPAIR POLICY
Pentair Equipment Protection products that: (i) are made to order, (ii) have been modified by Buyer, (ii)
have special finishes, or (iv) are determined by Pentair Equipment Protection to constitute “custom”
products that cannot be returned to stock or resold to other Buyers, will not be accepted for return by
Pentair Equipment Protection.
All returns require a Return Material Authorization number (RMA #), regardless of reason for return,
whether it be for warranty or out of warranty repair. Returns without an RMA # will be refused by our
Receiving Department. An RMA # is valid for 30 days.
- 38 -
© 2015 Pentair Equipment Protection
89104462
A. An RMA # will be issued by our Product Return Department in Anoka, MN at 763-422-2211. Buyer
should have following information available at time of RMA request:
1. Complete Model Number, Serial Number and description of damaged unit being returned.
2. Original Buyer Purchase Order number and date product was received by Buyer.
3. Quantity to be returned and a brief description of failure for each unit, if different.
4. Contact information of Buyer that must include: name of company, billing and shipping address,
phone, number, fax number, freight carrier and the name and phone number of a Buyer contact
who can elaborate on the claimed defect in detail.
5. Buyer must provide a Repair Purchase Order number for both warranty and out of warranty
repairs. The PO will not exceed 50% of a new unit. Buyer will be notified of repair charges that
exceed approved PO amount.
B. All returns to Pentair Equipment Protection must be securely packed, using original cartons if
possible. All returns must have the RMA number visible on the outside of the carton. Pentair
Equipment Protection is not responsible for material damaged in transit. Any refrigerant-bearing
Goods must be shipped upright for return.
C. Shipping cost for all non-warranty repairs is the responsibility of the sender and must be shipped
prepaid. Shipping costs for all warranty related repairs will be covered by Pentair Equipment
Protection provided the goods are returned using a Pentair Equipment Protection approved carrier.
If after diagnoses the product is determined by Pentair Equipment Protection not be covered under
warranty, Buyer will be responsible for all shipping charges and will be billed accordingly.
D. Non-warranty repairs are subject to a $105 minimum analysis fee. If approval is not received within
30 days, material will be scrapped and all shipping expenses and corresponding analysis fees will be
billed to Buyer.
E. At Buyer’s request, Failure Analysis can be provided by Pentair Equipment Protection for warrantable
goods at no charge. Failure analysis for non-warranty repairs are subject to a $150 per hour
Engineering charge plus any other incurred testing costs.
F. All returned merchandise must be sent to the following address: Pentair Equipment Protection, 2100
Hoffman Way, Anoka, MN 55303-1745.
G. Credit for accepted returns shall be at the original selling price or the current selling price, whichever
is lower, less the restocking charge indicated as follows:
1. Within 60 days of invoice date - 20% of applicable selling price.
2. Within 61-120 days of invoice date - 30% of applicable selling price.
3. Within 121-180 days of invoice date - 40% of applicable selling price.
4. Beyond 180 days - subject to individual review by Pentair Equipment Protection.
If product being returned for credit requires repair or modification, the cost of any labor or material
necessary to bring product into saleable condition will be deducted from credit. Buyer may not take credit
against returns without prior written Pentair Equipment Protection approval.
LIMITATION OF LIABILITY
PENTAIR EQUIPMENT PROTECTION WILL NOT BE LIABLE UNDER ANY CIRCUMSTANCES FOR ANY
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES, INCLUDING WITHOUT LIMITATION ANY LOST
PROFITS OR LABOR COSTS, ARISING FROM THE SALE, USE OR INSTALLATION OF THE GOODS, FROM
THE GOODS BEING INCORPORATED INTO OR BECOMING A COMPONENT OF ANOTHER PRODUCT,
FROM ANY BREACH OF THIS AGREEMENT OR FROM ANY OTHER CAUSE WHATSOEVER, WHETHER
BASED ON WARRANTY (EXPRESSED OR IMPLIED) OR OTHERWISE BASED ON CONTRACT, OR ON TORT
OR OTHER THEORY OF LIABILITY, AND REGARDLESS OF ANY ADVICE OR REPRESENTATIONS THAT
MAY HAVE BEEN RENDERED BY PENTAIR EQUIPMENT PROTECTION CONCERNING THE SALE, USE OR
INSTALLATION OF THE GOODS.
89104462
© 2015 Pentair Equipment Protection
- 39 -
Pentair Equipment Protection
2100 Hoffman Way
Minneapolis, MN 55303 USA
+1.763.422.2211
+1.763.576.3200
PentairProtect.com
Rev. G
© 2015 Pentair Equipment Protection
P/N 89104462
89104462
Download PDF