Quick Reference Guide Digital Sound Projector CD-ROM.

Quick Reference Guide Digital Sound Projector CD-ROM.
B
Digital Sound Projector
SWK-W16
Quick Reference Guide
For more detailed information, refer to the Owner’s Manual on the
CD-ROM.
Caution: Do not attempt to play this CD-ROM in an audio player.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
2
En
To assure the finest performance, please read this manual carefully. Keep it in a safe place for
future reference.
Install this sound system in a well ventilated, cool, dry, clean place - away from direct sunlight,
heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following
minimum clearances.
Top: 5 cm, Rear: 5 cm, Sides: 5 cm
Locate this unit away from other electrical appliances, motors, or transformers to avoid humming
sounds.
Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit
in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation
inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal
injury.
Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be
exposed to liquid dripping or splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal
injury.
– Containers with liquid in them, as they may fall and liquid may cause electrical shock to the
user and/or damage to this unit.
Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat
radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or
personal injury.
Do not plug in this unit to a wall outlet until all connections are complete.
Do not operate this unit upside-down. It may overheat, possibly causing damage.
Do not use force on switches, knobs and/or cords.
When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable.
Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.
Only voltage specified on this unit must be used. Using this unit with a higher voltage than
specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will
not be held responsible for any damage resulting from use of this unit with a voltage other than
specified.
Be sure to connect to an appropriate outlet with a protective grounding connection. Improper
grounding can result in electrical shock, damage to the device(s), or even fire.
To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a
wall outlet or this unit during a lightning storm.
Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any
service is needed. The cabinet should never be opened for any reasons.
When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power
plug from the wall outlet.
Be sure to refer to the “Troubleshooting” section of the Owner’s Manual on the CD-ROM for
common operating errors before concluding that this unit is faulty.
18 Before moving this unit, press A to set it to standby mode and disconnect the AC power plug from
the wall outlet.
19 Condensation will form when the surrounding temperature changes suddenly. Disconnect the
power cable from the outlet, then leave this unit alone.
20 When using this unit for a long time, this unit may become warm. Turn the power off, then leave
this unit alone for cooling.
21 Install this unit near the AC outlet and where the AC power plug can be reached easily.
22 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. When you
dispose of batteries, follow your regional regulations.
23 Excessive sound pressure from earphones and headphones can cause hearing loss.
24 Keep the product out of reach of children to avoid them swallowing small parts.
This unit is not disconnected from the AC power source as long as it is connected to the wall
outlet, even if this unit itself is turned off by A. This state is called the standby mode. In this
state, this unit is designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
Do not use this unit within 22 cm of persons with a heart pacemaker implant or defibrillator
implant.
Radio waves may affect electro-medical devices.
Do not use this unit near medical devices or inside medical facilities.
The name plate for SWK-W16 is located on the bottom of the unit.
We, Yamaha Music Europe GmbH hereby declare that this unit is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Yamaha Music Europe GmbH
Siemensstr. 22-34 25462 Rellingen, Germany
Tel: +49-4101-303-0
■ Notes on remote controls and batteries
■ For U.K. customers
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following conditions:
– places of high humidity, such as near a bath
– places of high temperatures, such as near a heater or stove
– places of extremely low temperatures
– dusty places
• Insert the battery according to the polarity markings (+ and -).
• Change all batteries if you notice the following conditions:
– the operation range of the remote control narrows
• If the batteries run out, immediately remove them from the remote control to prevent an explosion or
acid leak.
• If you find leaking batteries, discard the batteries immediately, taking care not to touch the leaked
material. If the leaked material comes into contact with your skin or gets into your eyes or mouth,
rinse it away immediately and consult a doctor. Clean the battery compartment thoroughly before
installing new batteries.
• Do not use old batteries together with new ones. This may shorten the life of the new batteries or
cause old batteries to leak.
• Do not use different types of batteries (such as alkaline and manganese batteries) together. Danger of
explosion may happen if batteries are incorrectly replaced. Specification of batteries may be different
even though they look the same.
• Before inserting new batteries, wipe the compartment clean.
• Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor
immediately.
• When not planning to use the remote control for long periods of time, remove the batteries from the
remote control.
• Do not charge or disassemble the supplied batteries.
If the socket outlets in the home are not suitable for the plug supplied with this appliance, it
should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Information for Users on Collection and Disposal of Old
Equipment and Used Batteries
These symbols on the products, packaging, and/or accompanying documents mean that
used electrical and electronic products and batteries should not be mixed with general
household waste.
For proper treatment, recovery and recycling of old products and used batteries, please
take them to applicable collection points, in accordance with your national legislation
and the Directives 2002/96/EC and 2006/66/EC.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
Note
The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is
hazardous if engaged in a live socket outlet.
■ Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE
FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the
letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the three pin plug.
To view the Owner’s Manual, click on “English” in the screen displayed automatically when you
insert the CD-ROM into your PC, or click on the model name if the screen to select models is
displayed, and then click on “English” in the next screen. Then, follow the onscreen instructions.
If the screen is not displayed automatically, open the “index.html” in the CD-ROM.
The Owner’s Manual contained in the CD-ROM can be downloaded from the following website:
URL : http://download.yamaha.com/
[Information on Disposal in other Countries outside the European
Union]
These symbols are only valid in the European Union. If you wish to discard these items,
please contact your local authorities or dealer and ask for the correct method of disposal.
Note for the battery symbol (bottom two symbol examples):
This symbol might be used in combination with a chemical symbol. In this case it
complies with the requirement set by the Directive for the chemical involved.
En
3
About this Quick Reference Guide
The Quick Reference Guide provides instructions for connecting a TV and BD/DVD
player to the unit, applying settings, and playing content. For more information on
operations, refer to the Owner’s Manual in the supplied CD-ROM.
•
indicates supplementary explanations for better use.
•
indicates precautions for use of the unit and its feature limitations.
Read the safety instructions described in this booklet before using the unit. For
instructions on how to operate or set the external devices, refer to documentation
supplied with each device.
Supplied accessories
Preparing remote control
Before connecting, make sure you have received all of the following items.
Remote control
Batteries
(AAA, R03, UM-4) (x2)
Before installing batteries or using the remote control, be sure to read battery and
remote control precautions in this booklet.
Optical cable (1.5 m)
Installing the batteries
Battery × 2
(AAA, R03, UM-4)
Power cable (2 m)*
IntelliBeam microphone
(6 m)
Cardboard microphone
stand
Stands (x2)
Screws (For the stands; x2)
Subwoofer cable (3 m)
Press down on the arrow
and slide the cover in the
direction in which it
points.
Slide the cover back to close it.
Operation range
System control cable
(3 m)
• Owner’s Manual CD-ROM
• Quick Reference Guide (this booklet)
• MusicCast Setup Guide
Within 6 m
* The shape of the power cable plug varies depending on where the unit was
purchased.
Devices and cables required for connection
• TV
4
En
• BD/DVD player
Supplied accessories
• HDMI cables (x2)
1 2 3 4
a Installation
This unit reflects sound beams off of walls and a ceiling to create the surround sound effect. The position of this unit in relation to the listening position, walls, and a ceiling is important
to achieving the desired surround sound effects. Refer to pages 5 to 7 when installing the unit. When installing this unit on a rack behind which there is limited space, for example, it
may be easier to connect external devices to this unit first. This will depend upon the installation location. See page 8 for information regarding the connection of external devices.
Notes
• Be sure to install this unit on a large, stable stand where it does not fall subject to vibrations, such as from an earthquake, and where it is out of the reach of children.
• There is a built-in antenna on the top of the unit. Do not install it on a metal rack, and do not stack metal items on top of the unit.
• The unit’s speakers are not magnetically shielded. Do not install hard disk drives or similar devices near the unit.
• Do not stack the unit directly on top of other playback devices, or vice versa. Heat and vibrations may result in damage or malfunction.
Recommended place for installation
• Be sure that the unit installed with at least 5 cm
of empty space above and below it.
• Install the unit in the center of the left and right
walls.
• This unit can be mounted on a wall. See page 17
in the Owner’s Manual.
• The listening position (such as sofa, etc.) should be
located at the front of the unit.
• The distance between the listening position and the
unit should be more than 1.8 m.
• Set the listening position as far from the back wall as
possible (the optimal listening position is halfway
between the unit and the back wall, or slightly closer
to the back wall).
• Leaving as much space as possible in a
diagonal direction in front of, and above, the
unit when installing it.1
• Attach the supplied stands to the unit if it will
be installed on a rack 2 (p. 7).
1
Height channel audio is output in a diagonal
direction upward and forward from the unit. As
height channel sound beams are reflected off the
ceiling, sound can be heard from above.
2
Depending upon the rack, table-top stand, or floor
stand used, the stands may not be necessary.
• To achieve desired surround sound effects, be
sure that obstacles such as furniture may not
obstruct the path of sound beams (p. 6).
a Installation
En
5
1 2 3 4
Example for installing the unit
This unit outputs sound beam as shown in the illustrations below. Install this unit where there are no obstacles such as furniture obstructing the path of sound beams. Otherwise, the
desired surround sound effects may not be achieved.
If the unit is installed so that it is parallel to a wall, install it as close to the exact center of the wall as possible.
If the unit is installed in a corner of a room, position it at a 40–50° angle to the adjacent walls.
• See pages 14 to 16 in the Owner’s Manual for additional installation examples.
Coner installation
Parallel installation
Viewed from above
Viewed from the side
Objects,
such as
furniture
Sound beams
are reflected off
the ceiling
Sound beam output varies depending upon the 3D surround/Surround setting (pages 38
and 39 in the Owner’s Manual) and the channel output setting (page 73 in the Owner’s
Manual). The illustration above shows the path of sound beams when 3D surround is
enabled and “Front” in the Channel Out setting is set to “Beam”.
6
En
a Installation
Viewed from above
Viewed from the side
Sound beams
are reflected off
the ceiling
40° to 50°
Objects, such as
furniture
The illustrations above show the path of sound beams when 3D surround is enabled
(page 38 in the Owner’s Manual) and “Front” in the Channel Out setting is set to “Stereo”.
(page 73 in the Owner’s Manual).
1 2 3 4
Unrecommended listening environments
This unit creates surround sound by reflecting projected sound beams off the walls and
the ceiling of your listening room. The surround sound effects produced by this unit
may not be sufficient when this unit is installed in the following locations.
• Rooms with walls inadequate for reflecting sound beams
• Rooms with acoustically absorbent walls and ceiling
Installing the stands
Install the stands (supplied) on the bottom of the unit. Align and insert the protrusion on
the stands into the holes on the rear panel of the unit as shown in the illustration, and
then tighten the screws (supplied) to lock the stands in place. The stands need not be
installed when the unit is mounted on a wall using the optional Wall Mount Bracket
SPM-K30.
• Rooms with measurements outside the following range:
W (3 to 7 m) × H (2 to 3.5 m) × D (3 to 7 m)
• Rooms where objects such as furniture are likely to obstruct the path of sound beams
• Rooms with less than 1.8 m from the listening position to this unit
• Rooms where the listening position is close to the walls
• Rooms where the listening position is not in front of this unit
• Rooms with a complex shape, such as a slanted ceiling (ceiling lights do not obstruct
sound beams)
Stand (supplied)
Enjoying surround effects regardless of conditions (My
Surround)
The My Surround function creates rich surround sound effects in rooms with less than
optimal surround sound conditions. See “Channel Out” (page 73 in the Owner’s
Manual) for more information.
• This unit’s AUTO SETUP (IntelliBeam) can be used to automatically adjust sound beams to achieve the
optimal surround playback environment according to the listening room setup (p. 12).
Screws (supplied)
Stand (supplied)
a Installation
En
7
1 2 3 4
b Connections
Connecting a TV and BD/DVD player
For the cable connection, follow the procedure below. See pages 23 to 24 in the Owner’s Manual when connecting other playback devices such as a game console.
TV
Video signals
OPTICAL
OUTPUT
Audio signals
HDMI INPUT
2
1
1
HDMI cable (optional)
The digital audio/video signals from the BD/DVD player
are input to this unit.
3
• This unit supports HDCP version 2.2, a copy protection technology. When
using an HDCP 2.2-compliant playback device, such as a set-top box,
connect it to the unit via the HDMI IN 1 jack.
Use an optical cable when
connecting a TV that does not
support Audio Return Channel.
2
1
2
HDMI
OUTPUT
1. Remove the cap
HDMI cable (optional)
Digital video from the BD/DVD player is displayed on the
TV.
• Connect the unit to the HDMI IN jack (one compatible with HDCP 2.2) on
an HDCP 2.2-compliant TV to enjoy playback of 4K video.
2. Check the direction of
the plug
OUT
(ARC)
BD/DVD player
IN 1
(HDCP2.2)
Audio Return Channel (ARC) supported TV
TV
• Connect an HDMI cable to the audio return channel supported jack (the jack with
“ARC” indicated) on TV.
• Enable the HDMI control function of this unit to activate the Audio Return
Channel (ARC). See page 77 in the Owner’s Manual.
IN 1
(HDCP2.2)
IN 2
What is Audio Return Channel (ARC)?
IN 3
IN 4
HDMI
OUT
(ARC)
NETWORK
UPDATE ONLY
AC IN
SYSTEM
SUBWOOFER
CONNCETOR
OUT
R
AUX1
L
AUX2
TV
OPTICAL
IR-IN
IR-OUT
RS-232C
• In order for the unit to play audio from a TV, the TV must usually be connected to
the unit via an audio cable as well as an HDMI cable. If, however, the TV
supports Audio Return Channel (ARC), TV audio signals can be input to the unit
via the HDMI cable that outputs video signals from the unit to the TV.
For a wired network connection, connect one end of the network
cable to the NETWORK jack on the rear panel of the unit and the
other end to a router. For details, see page 52 in the Owner’s
Manual.
8
En
b Connections
1 2 3 4
Connecting a subwoofer
Follow the procedure below to connect the SWK-W16 to the subwoofer.
A subwoofer can be connected to the unit for use with the unit. There are two ways to
connect a subwoofer to the unit: use a third-party RCA monaural cable, or use the
wireless subwoofer kit SWK-W16 to connect via a wireless connection.
1
If a Yamaha subwoofer is connected via the SYSTEM CONNECTOR jack, it
turns on and off when the unit is turned on and off.
2
• See page 25 in the Owner’s Manual for more information.
Connecting a subwoofer via cable
Use a third-party RCA monaural cable to connect the subwoofer to the unit via the
monaural input jack on the subwoofer and the SUBWOOFER OUT jack on the unit.
Connect subwoofer cable to the SUBWOOFER OUT jack on the
SWK-W16 and the subwoofer’s input jack.
Plug the power cables for the subwoofer and the SWK-W16 into an
AC wall outlet.
When the unit is turned on, a wireless connection between the unit and
SWK-W16 will be established. The status indicator glows green once the
wireless connection is established.
If a Yamaha subwoofer is connected via the SYSTEM CONNECTOR jack, it turns on
and off when the unit is turned on and off.
SWK-W16
Status indicator
The unit (rear)
2
Subwoofer
Rear side
IN 1
(HDCP2.2)
To an AC wall outlet
IN 2
IN 3
SYSTEM
CONNECTOR
IN 4
HDMI
OUT
(ARC)
R
AUX1
L
AUX2
TV
OPTICAL
IR-IN
IR-OUT
INPUT
SYSTEM
CONNECTOR
SUBWOOFER
OUT
SYSTEM
CONNECTOR
1
1
NETWORK
UPDATE ONLY
SYSTEM
SUBWOOFER
CONNCETOR
OUT
SUBWOOFER
OUT
RS-232C
• When the unit is connected to the subwoofer via the cable, set the subwoofer output to “Wired” in the setup
menu (page 74 in the Owner’s Manual).
Using the wireless subwoofer kit SWK-W16
Subwoofer cable
(supplied)
INPUT
Subwoofer
The wireless subwoofer kit SWK-W16 enables wireless connection of a subwoofer to the
unit. Install the SWK-W16 on or near the subwoofer.
SYSTEM
CONNECTOR
System control cable
(supplied)
2 To an AC wall outlet
• See “Troubleshooting” (pages 93 and 99 in the Owner’s Manual) if the indicator on the wireless subwoofer
kit does not glow green.
SWK-W16
Subwoofer
b Connections
En
9
1 2 3 4
Connecting the power cable
z
After all the connections are complete, plug in the power cable.
While this screen is displayed, an iOS device (such as an iPhone)
can be used to easily connect the unit to a wireless network. Follow
the procedure below.
If you will not use an iOS device to connect to a wireless network,
press the RETURN ( ) key and proceed to “c Auto setup for
appropriate surround effects (IntelliBeam)”.
The unit (rear)
IN 4
HDMI
OUT
(ARC)
AC IN
SYSTEM
SUBWOOFER
CONNCETOR
OUT
R
AUX1
L
AUX2
TV
OPTICAL
IR-IN
• This screen will not be displayed if the unit is connected to a router via its
NETWORK jack (wired connection).
To an AC wall outlet
• See page 51 in the Owner’s Manual for wireless network connection methods
other than “Share Wi-Fi Settings”, or for more information regarding wired and
wireless networks.
Connecting the unit to a wireless network
SETUP (
1
)
Turning on the unit
The screen below is displayed.
ENTER
RETURN (
)
1
Share
Press the z key.
When the unit is turned on for the first time after purchase,
the screen below will be displayed on the TV. (“ViewScreen”
is shown in the front panel display.)
Share
Y
(
n
u
l
o
W
e
s
a
u
i
t
i
t
w
n
e
c
F
o
g
r
an
i)
rk
a
.
s
s
w
d
Wi-Fi
h
e
i
e
a
t
t
v
Settings
• When the screen is not displayed, use the input button on the TV’s remote control
to switch input so that video input from this unit is displayed. When this unit is
connected to the TV as shown on page 8, select “HDMI 1”.
• The language used for menu display (OSD Language) can be selected from the
screen shown above. Use the W/X key to select the language, and follow the
on-screen instructions. The OSD language can also be changed from the setup
menu at any time. Press and hold the SETUP ( ) key until the “OSD Language”
menu is displayed on the TV, and use the S/T key to select the language. Press
the SETUP ( ) key to exit the setup menu.
En
b Connections
M
c
n
W
y
a
o
e
i
o
k
n
t
u
Wi-Fi
e sure your i
nected to you
work, and the
Fi settings s
r iOS device.
Settings
OS device is
r Wi-Fi
n open the
creen of
[ENTER]:Confirm
[RETURN]:Cancel
re the wireless
tings of the
h Sound Projector
ice with iOS7 or
[ENTER]:Start
[RETURN]:Cancel
[
]:OSD Language
10
Press the ENTER key.
• You need iOS device with iOS 7.1 or later.
• Before proceeding, confirm that your iOS device is connected to a wireless
router (access point).
1 2 3 4
2
3
Press the ENTER key.
Display the Wi-Fi setup screen on the iOS device
and select the unit from “SETUP A NEW AIRPLAY
SPEAKER...”.
iOS (an example of English version)
The name of the unit
ENTER
4
Select the network (access point) of which you want
to share the settings with the unit.
iOS (an example of English version)
Tap here to start setup
The network currently selected
The name of the unit
• You can use this function to connect to a wireless network at any time by selecting
“Share Wi-Fi Settings (iOS)” from the setup menu. However, be aware that if a
different wireless network, or a Bluetooth device, has already been configured,
doing so will erase any previous settings.
b Connections
En
11
1 2 3 4
c Auto setup for appropriate surround effects (IntelliBeam)
First use the “IntelliBeam” function to adjust each channel so that this unit provides the
optimal viewing and listening environment.
• Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam
microphone at the same height as your ears would be when you are seated.
• Position the IntelliBeam microphone so that it is parallel with the floor.
• The AUTO SETUP procedure may not be run successfully if this unit is installed in one of the rooms
described in “Unrecommended listening environments” (p. 7).
The My Surround function can be used to enjoy rich surround sound in these types of rooms as well. See
“Channel Out” (page 73 in the Owner’s Manual) for more information.
• Do not connect the IntelliBeam microphone to an extension cable as doing so may result in an inaccurate
sound optimization.
IntelliBeam microphone
Upper limit
Center height of
this unit
Within 1 m
Installing the IntelliBeam microphone
Within 1 m
1
Place the IntelliBeam microphone at your normal listening position.
Cardboard
microphone stand
Listening position
❑ Assembling the supplied cardboard microphone stand
1.8 m or more
1
2
3
Lower limit
Fit in
Remove
Fit in
Place horizontally
4
5
Run through
Center line
IntelliBeam microphone
Cardboard microphone stand
Make sure that there are no obstacles between the IntelliBeam microphone and the
walls in your listening room as these objects obstruct the path of sound beams.
However, any objects that are in contact with the walls will be regarded as a protruding
part of the walls.
12
En
c Auto setup for appropriate surround effects (IntelliBeam)
1 2 3 4
3
Using AUTO SETUP (IntelliBeam)
Connect the IntelliBeam microphone to the INTELLIBEAM MIC jack
of the unit.
• Test tones output during measurement are loud. Perform AUTO SETUP when no children are around and
there is no possibility of their entering the listening room, as their hearing may be impaired.
• If there are curtains in your listening room, we recommend following the procedure below.
1. Open the curtains to improve sound reflection.
2. Run “Beam optimize only” (page 33 in the Owner’s Manual).
3. Close the curtains.
4. Run “Sound optimize only” (page 33 in the Owner’s Manual).
INTELLIBEAM MIC
INTELLIBEAM MIC
• Make sure that your listening room is as quiet as possible. For accurate measurement, turn off air
conditioner or other devices that make noises.
1
IntelliBeam microphone
Turn the unit and your TV on.
Cardboard microphone stand
• When a subwoofer is connected to the unit, turn on the subwoofer, and set the volume and crossover
frequency as shown below.
Set the volume to half
Set the crossover frequency to maximum
VOLUME
CROSSOVER
HIGH CUT
MIN
2
MAX
MIN
The screen below is displayed after connecting IntelliBeam microphone to the
unit.
P
P
1
j
a
M
A
p
[
MAX
Switch TV input to display video input from this unit (page 28 in the
Owner’s Manual).
l
l
.
e
t
e
f
l
E
e
e
8
c
a
t
e
N
a
a
m
t
e
s
e
a
T
(
s
s
/
o
a
u
r
s
E
P
e
e
6
r
r
r
RE
c
p
ft
.
l
em
[E
e l
R]:
AUT
PARA
onne
lace
awa
The
evel
ent
NTER
eave
Star
O
TI
ct
t
y
MI
w
ta
]
t
t
SE
ON
t
he
fr
C
he
ke
is
he
[R
TU
&
he
M
om
sh
n
s
p
r
ET
P
C
M
IC
S
ou
se
ab
re
oo
UR
HEC
IC.
at
oun
ld
ate
out
sse
m.
N]:
K)
least
d Probe set
d.
3min.
d,
Cancel
“AUTO SETUP” in the “IntelliBeam” menu can automatically adjust the
following two settings.
Beam optimize only
This feature optimizes the beam angle so that the parameter best
matches your listening environment.
Sound optimize only
This feature optimizes sound quality for each channel by
measuring the acoustic characteristics of the listening
environment.
“Beam optimize only” or “Sound optimize only” can be measured separately in
the setup menu (page 33 in the Owner’s Manual).
• Follow the instructions below and then leave the room. If you remain in the room, you may obstruct
the beam, or the microphone may pickup any sounds you make, possibly resulting in improper
measurement.
c Auto setup for appropriate surround effects (IntelliBeam)
En
13
1 2 3 4
4
Press the ENTER key to start the AUTO SETUP
procedure and then leave the room within 10
seconds.
5
Press the ENTER key.
The measurement results are applied and saved in the unit.
AUTO
AUTO
Will
SETUP
begin
Please
in
leave
SETUP
COMPLETE
START
10
the
Please remove the MIC
from Sound Projector
and the listening position.
sec.
room.
Press [SYSTEM MEMORY]
to save set-up in the
----------
key
memory.
SYSTEM
MEMORY
[RETURN]:Cancel
• You can save several measurement results by pressing
the SYSTEM MEMORY 1, 2, or 3 key.
The screen changes
automatically as measurement
progresses.
SHOW
ENTER
RETURN (
RESULT
MEASUREMENT
)
E
F
S
S
N
R
U
U
V
O
R
B
I
N
R
W
RONMENT
T
:Be
OUND :Be
OOFER:Wi
When the SYSTEM MEMORY 1 key is pressed, “M1
Saving” is displayed, and settings are saved.
C
a
a
r
• If ambient noise is picked up after measurement begins,
an error message is displayed in the “AUTO SETUP
COMPLETE” screen prompting you to begin
measurement again. Press the ENTER key to exit the
error message screen, and begin measurement again.
COMPLETE.
HECK:Success
m
m
ed
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
• See page 45 in the Owner’s Manual for more information on the system
memory function.
If the AUTO SETUP procedure is complete, this unit rings
the chimes.
6
• The AUTO SETUP procedure takes about 3 minutes.
• To cancel the AUTO SETUP procedure after it is started, or if you do not
want to apply the results, press the RETURN ( ) key.
• If an error occurs, an error buzzer sounds and an error message is
displayed. For details on error messages, see page 34 in the Owner’s
Manual.
Remove the IntelliBeam microphone.
The “AUTO SETUP COMPLETE” screen closes.
The IntelliBeam microphone is sensitive to heat, so should
not be placed anywhere where it could be exposed to direct
sunlight or high temperatures (such as on top of AV
equipment).
INTELLIBEAM MIC
14
En
c Auto setup for appropriate surround effects (IntelliBeam)
INTELLIBEAM MIC
1 2 3 4
d Playback
HDMI1
TV
VOL (+/-)
Enjoying TV
1
2
Select the desired TV channel.
Press the TV key.
• When audio is output from the TV speaker, set TV’s audio output to an option
(output to the unit) other than TV. Refor to documentation supplied with TV for
more information.
Playing a DVD or BD
The following explains the playback procedure when this unit is
connected to the TV and BD/DVD player as shown in “Connecting
a TV and BD/DVD player” (p. 8).
1
Turn on the TV and BD/DVD player connected to this
unit.
2
Press the HDMI key to select the BD/DVD player as
the input source.
• HDMI control function
You can use the TV remote control to operate this unit if your TV supports the
HDMI control function. See page 35 in the Owner’s Manual.
3D SURROUND
SURROUND
STEREO
TARGET
HDMI1
Input source name
3
Use the TV’s remote control to switch the TV’s input
to HDMI 1.
4
5
6
Play back a DVD or BD.
Press the VOL (+/-) key to adjust the volume.
Press the 3D SURROUND, SURROUND, STEREO, or
TARGET key according to your preferences.
See page 38 in the Owner’s Manual for details.
When this unit does not play back, check the following
• The unit and BD/DVD player are connected correctly.
• The audio output settings of the BD/DVD player is set to digital sound output
(bitstream).
• The TV’s input is switched to this unit.
d Playback
En
15
1 2 3 4
Playback with 3D surround sound
Playback with surround sound
In addition to 5-channel sound beams used for surround sound
playback in the horizontal direction, surround sound can be heard
from above by directing two sound beams (from height channels)
upward and reflecting them off the ceiling. Compared to surround
sound playback in only the horizontal direction, this gives the
sound field (spatial expression with sounds) a greater sense of
immersion and reality.
5-channel sound beams create a sound field for surround sound
playback without using height channel sound beams.
Sound beams
Channels created from the front and rear sound
beams
Sound beams in the horizontal direction
Sound beams output from height channels
3D SURROUND
Channels created from the front and rear sound
beams
SURROUND
1
Press the 3D SURROUND key to switch to 3D
surround mode.
“3D SUR.” is shown in the front panel display.
3D SUR.
16
En
d Playback
1
Press the SURROUND key to switch to surround
mode.
“SURROUND” is shown in the front panel display.
SURROUND
1 2 3 4
Enjoying three-dimensional surround
sound (CINEMA DSP 3D/CINEMA DSP)
CINEMA DSP
MusicCast CONTROLLER
Select the desired CINEMA DSP program according to the audio
source and your preferences. Yamaha’s exclusive sound field
reproduction technology (CINEMA DSP 3D/CINEMA DSP) easily
reproduces realistic sound fields comparable to those found in
movie theaters and concert halls, allowing users to enjoy a natural
and three-dimensional listening environment.
The free dedicated app for mobile devices, MusicCast
CONTROLLER, allows you to listen to music stored on mobile
devices such smartphones, or on servers, or to listen to Internet
radio stations and many kinds of major streaming services.
Sound fields are reproduced using CINEMA DSP 3D for 3D
surround sound playback, and CINEMA DSP for surround sound
playback. The same programs can be selected for both CINEMA
DSP 3D and CINEMA DSP.
See the “MusicCast Setup Guide” for details.
This app also allows you to distribute content to other
MusicCast-enabled devices for synchronized playback.
Search for “MusicCast CONTROLLER” on the App Store or Google
Play.
1
Press the 3D SURROUND or SURROUND key to
enable 3D surround or surround playback mode.
2
Press the CINEMA DSP (MOVIE, MUSIC, or
ENTERTAINMENT) key repeatedly to select the
desired program.
The free dedicated app for mobile devices, HOME THEATER
CONTROLLER (WLAN), allows you to easily operate the unit,
performing such tasks as configuring sound beams on a visual
screen, selecting an input source, and adjusting the volume on a
mobile device.
The CINEMA DSP program name is shown in the front
panel display.
Search for “HOME THEATER CONTROLLER (WLAN)” on the App
Store or Google Play.
HOME THEATER CONTROLLER (WLAN)
SURROUND
3D SURROUND
• Press the OFF key to disable CINEMA DSP. Audio content is played in 3D
surround mode or surround mode.
• Refer to page 39 in the Owner’s Manual for more information.
The unit is equipped with a number of other functions not
described in this booklet. See the Owner’s Manual for details.
d Playback
En
17
AVEG1A1102C
Important Notice:Guarantee Information for
customers in EEA* and Switzerland
English
For detailed guarantee information about this Yamaha product, and Pan-EEA* and Switzerland
warranty service, please either visit the website address below (Printable file is available at our
website) or contact the Yamaha representative office for your country. *EEA:European
Economic Area
http://europe.yamaha.com/warranty/
© 2015 Yamaha Corporation
Printed in Indonesia ZS46210
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement