PSB9240DF GE Profile Series 30 in. Single Wall Oven with Advantium

PSB9240DF  GE Profile Series 30 in. Single Wall Oven with Advantium
solid floor
Required
cutout location
36-3/4"
minimum
from floor
29-3/4"
PSB9240DF
Suitable
bracing
™
to support
runners
3/8" Plywood
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
(Must Support
150 lbs.)
cabinet
21-5/8"
®
width
GE Profile Series
30
in.
Single
Wall
Oven
with
Advantium
Technology
over centerline
Advantium
Wall
Oven
Dimensions (in inches)and
of cabinet
A=Allow 1" overlap of oven over bottom edge of cutout.
Cabinet Installation (in inches)
B=Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
(Must support 130 lbs.) ™
Advantium wall oven/GE Profile Series cooking tower
dimensions and cabinet installation information (in inches)
Note: Cabinets
installed adjacent
to wall ovens must
have an adhesion
spec of at least a
194°F temperature
rating.
Note: 2" minimum
between cutouts
when installed
above warming
drawer or single
wall oven.
Installation
Information:
Before installing,
consult installation
instructions packed
with product for ­current
dimensional data.
4-3/16"
25-1/8"
Cutout width
Note: Cabinets installed adjacent
to wall ovens must have an adhesion
spec of at least 194° F temperature rating.
4-3/16
Cabinet width
23-1/2"
Cutout depth
21-1/2"
To Back of Control
Junction box
location
(240-volt
models only)
Junction box location (240-volt models only)
A
19-1/8"
21-1/2"
29-3/4"
A
B
19-1/8"
2-1/2" MIN between cutouts
recommended—2" MIN required
To back
of Control
A
CL
B
Conduit
(46" long)
B
17-1/2"
Cutout height
Oven Dimensions (in inches)and
Cabinet Installation (in inches) Construct Solid
2x4’s or
25-1/8"
Bottom Min.
3/8" Plywood Cutout widt
Supported by
2 x 4 or 1 x 2
Runners, all
Four Sides.
21-1/2"
(Must Support
To Back of Control
150 lbs.)
equivalent
Construct Solid Bottom
MIN 3/8" Plywood Supported by solid floor
2 x 4 or 1 x 2 Runners, all Four Sides.
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
Note: Cabinets installed adjacent
Required
29-3/4"
to wall ovens must have an adhesion
cutout location
spec of at least 194° F temperature rating.
36-3/4"
minimum
from floor
9-1/4" cutout height
28-1/2" cutout width
Suitable
bracing
to support
runners
Conduit
(48-1/2"
long) Wall
Advantium
2" MIN between cutouts
cabinet
width
21-5/8"
over centerline
of cabinet
A=Allow 1" overlap of oven over bottom edge of cutout.
B=Allow 11/16"-3/4" for overlap of oven over side edges of cutout.
19-1/8"
(Must
support
130 lbs.)
1" Min.
above toekick
or adjust
to oven installation height
Note: Advantium 240 volt models cannot be installed under 36 inches height.
Note: Use of the accessory drawer will replace the bottom trim piece for applicable
installations. Please see installation instructions for full details.
CL
4-3/16
Cabinet width
2x4’s or
equivalent
solid floor
A
Conduit
(48-1/2"
long)
29-3/4"
Junction box location (240-volt models only)
A
19-1/8"
21-1/2"
2-1/2" MIN between cutouts
recommended—2" MIN required
To back
of Control
Suitable
29-3/4"
bracing
to support
runners
For answers to your Monogram® or GE®
appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
Conduit
(46" long)
B
A
21-5/8"
over
centerline
B
of cabinet Construct Solid Bottom
MIN 3/8" Plywood Supported by
Listed by
Underwriters
Laboratories
cabinet
width
A=Allow 1" overlap of oven over b
(Must support 130 lbs.)
2 x 4 or 1 x 2 Runners, all Four Sides.
B=Allow 11/16"-3/4" for overlap o
(Must Support 150 lbs. for Advantium)
(Must Support 200 lbs. for Wall Oven)
Specification
9-1/4" cutout height
28-1/2" cutout width
Revised 7/14
PSB9240DF
GE Profile™ Series 30 in. Single Wall Oven with Advantium® Technology
Preparation with an Accessory Drawer
Prepare the opening
The Advantium 240V can be installed in combination with
other GE/Monogram appliances. Always follow each product's
Installation Instructions to compete the installation.
Single Oven Installation:
Order a 30" wide single oven cabinet or cut the opening in a wall
to the dimensions shown.
* For existing cutouts, a
23-1/2”
30”
maximum width of 28-1/2"
is acceptable. If the opening
is slightly wider, secure a
25-1/4”
Min.
furring strip on each side of
the cutout for securing the
oven.
21”
• Always maintain 36-3/4"
Construct
Base
minimum height from
Min. 3/8”
Plywood
the floor to the cutout in
5” min.
Supported
from floor
by 2x4 or 2x2
any single or combined
1” min.
Runners all
installation.
above
Four Sides
toekick
• Allow 3/4" to 2-1/8" case
trim overlap on the sides
and 7/8" overlap on the
bottom of the opening for
all models. The amount of overlap on the sides depends on the
actual cutout width. Allow 1-1/4" case trim overlap on the top for
models PSB9240 and for models ZSC2200, ZSC2201 and ZSC2202.
• Oven overlaps will conceal cut edges on all sides of the opening.
Prepare the opening (cont.)
When installed over a single oven or a
warming drawer, allow at least 2" between
the two openings. This separation will
provide clearance for bottom overlap of the
Advantium 240V and the other appliance
overlaps.
Construct a solid oven floor of 3/8" min. thick
plywood supported by 2 x 4 or 2 x 2 runners
on all sides.
• the support must be level and rigidly
mounted, flush with the bottom edge of
the
cutout.
Installation
over a GE/Monogram
Warming Drawer:
23-1/2”
30”
25-1/4”
Min.
21”
5” min.
from floor
1” min.
above
toekick
Construct
Solid Bottom
Min. 3/8”
Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
2” Min.
(3” recommended)
Per warming
drawer
requirement
* For existing cutouts, a maximum width of
28-1/2" is acceptable. If the opening is slightly
wider, secure a furring strip on each side of
the cutout for securing the oven.
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
Installation over a GE/Monogram Oven
and Warming Drawer:
Warming Drawer:
30”
23-1/2”
25-1/4”
Min.
21”
Construct Solid
Bottom Min.
3/8” Plywood
Supported by
2x4 or 2x2
Runners all
Four Sides
2” Min.
(3” recommended)
Per Oven
Requirement
5” min.
from floor
1” min.
above
toekick
2” Min.
Per warming drawer requirement
* F or existing cutouts, a maximum width of
28-1/2" is acceptable. If the opening is slightly
wider, secure a furring strip on each side of
the cutout for securing the oven.
Note: Additional clearances between the
cutouts may be required. Check to be sure the
oven supports above the Warming Drawer
location do not obstruct the required interior
depth and height. See Warming Drawer
installation instructions for details.
Caution: For personal safety, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight
of this approximate 80-pound oven and 30pound drawer, plus additional oven loads of up
to 50 pounds or a total weight of 160 pounds.
Specification Revised 7/14
PSB9240DF
GE Profile™ Series 30 in. Single Wall Oven with Advantium® Technology
Features and Benefits
•Speedcook oven (240) - Enjoy oven-quality results two to eight times
faster than a conventional oven
•Multiple cooking functions - Expand your cooking versatility with an
all-in-one oven
•Halogen heat - Skip the preheating with nearly instantaneous
halogen heat
•Over 175 preprogrammed menu selections - Preprogrammed
selections make meals easy
•Custom recipe saver - Conveniently store cooking instructions for up
to 30 different recipes
•Three-speed, 300-CFM venting system - Quickly moves smoke and
steam up from the cooktop
•Allows for use with JX2200/2201 storage drawer
• Model PSB9240DFWW - White on white
• Model PSB9240DFBB - Black on black
PSB9120/9240
Specification Revised 7/14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement