Viking Installation Guide ®
Viking Installation Guide
®
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
Professional Freestanding Dual Fuel Ranges
F20533E EN
(080610)
Table of Contents
IMPORTANT–Read and Follow!
Warnings & Important Safety Instructions_____________________________________________________3
• Before beginning, please read these
instructions completely and carefully.
Dimensions __________________________________________________________________________________6
Specifications ________________________________________________________________________________8
Clearance Dimensions (Proximity to Cabinets) _______________________________________________10
Clearance Dimensions (Wood/Composite Overlay)___________________________________________11
To minimize exposure to these substances,
always operate this unit according to the
instructions contained in this book and
provide good ventilation.
• DO NOT remove permanently affixed
labels, warnings, or plates from product.
This may void the warranty.
Your safety and the safety of others is
very important.
Electrical & Gas Requirements ______________________________________________________________12
General Information ________________________________________________________________________14
Installation __________________________________________________________________________________15
Door Removal __________________________________________________________________________15
Leg Installation _________________________________________________________________________16
Electrical Connection (3 Wire) ___________________________________________________________17
Electrical Connection (4 Wire) ___________________________________________________________19
Leveling/Adjustments/Alignment________________________________________________________21
Anit-tip Device Installation ______________________________________________________________22
We have provided many important safety
messages in this manual and on your
appliance. Always read and obey all
safety messages.
• All local and national codes and ordinances
must be observed. Installation must
conform with local codes or in the absence
of codes, the National Fuel Gas Code
ANSIZ223.1/NFPA-54 –latest edition.
This is the safety alert symbol. This
symbol alerts you to hazards that
can kill or hurt you and others.
• The installer must leave these instructions
with the consumer who should retain for
local inspector’s use and for future
reference.
All safety messages will be preceded by
the safety alert symbol and the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
Connecting Gas & Electrical ____________________________________________________________23
Standoff Bracket Removal_______________________________________________________________24
Final Installation ________________________________________________________________________24
Door Replacement and Adjustment _____________________________________________________25
Final Preparation____________________________________________________________________________26
Performance Checklist ______________________________________________________________________26
Service & Registration ______________________________________________________________________27
In Canada: Installation must be in accordance
with the current CAN/CGA B149.1 & 2 Gas
Installation codes and/or local codes. Electrical
installation must be in accordance with the
current CSA C22.1 Canadian Electrical Codes
Part 1 and/or local codes.
DANGER
Hazards or unsafe practices
which WILL result in severe personal
injury or death.
WARNING
Hazards or unsafe practices
which COULD result in severe personal
injury or death.
Commonwealth of Massachusetts:
• Installations and repairs must be
performed by a qualified or licensed
contractor, plumber or gas fitter, qualified
or licensed by the state, province or region
where this appliance is being installed.
CAUTION
Hazards or unsafe practices which
COULD result in minor personal injury or
property damage.
• Use only gas shut-off valves approved for
use within the state, province or region
where this appliance is being installed.
All safety messages will identify the
hazard, tell you how to reduce the chance
of injury, and tell you what can happen if
the instructions are not followed.
• A flexible gas connector, when used,
must not exceed 3’ (.9 m).
California Proposition 65
Burning gas cooking fuel generates some byproducts that are on the list of substances
known to cause cancer or reproductive harm.
2
3
IMPORTANT–Read and Follow!
DANGER
Chemical hazard.
Fire/explosion hazard.
IF THE INFORMATION IN
THIS MANUAL IS NOT
FOLLOWED EXACTLY, A
FIRE OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY, OR DEATH.
• DO NOT store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
• WHAT TO DO IF YOU SMELL GAS:
–DO NOT try to light any appliance.
–DO NOT touch any electrical switch;
DO NOT use any phone in your
building.
–Immediately call your gas supplier from
a neighbor’s phone.
–Follow the gas supplier’s instructions.
–If you cannot reach your gas supplier,
call the fire department.
• Installation and service must be
performed by a qualified installer, service
agency, or the gas supplier.
To avoid risk of property
damage and/or personal injury
or death; this appliance is not
too be used as a heating source.
• Benzene is a chemical which is part of
the gas supply to this cooking product,
which is consumed in the flames during
combustion. Exposure to a small
amount of benzene is possible if a gas
leak occurs. Formaldehyde and soot are
by-products of incomplete combustion.
• This appliance contains or produces
chemicals which can cause serious
injury or death and which are known to
the state of California to cause cancer,
birth defects or other reproductive harm.
To reduce the risk from substances in
the fuel or from fuel combustion make
sure this appliance is installed,
operated, and maintained in accordance
to the instructions in this document.
DANGER
WARNING
DANGER
Gas leak hazard.
Moving hazard.
To avoid risk of personal injury
or death; leak testing of the
appliance must be conducted
according to the manufacturer’s
instructions. Before placing appliance in
operation, always check for gas leaks
with soapy water solution.
• DO NOT USE AN OPEN FLAME TO
CHECK FOR GAS LEAKS.
To avoid risk of severe
personal injury; this appliance
requires two or more personnel
while handling and moving. Possible
use of appliance moving devices is
recommended.
WARNING
Tipping hazard.
•
•
•
•
To reduce the risk of property
damage or personal injury;
install anti-tipping device
provided in accordance with
the installation instructions in
this document. Device must be
engaged properly to prevent
product from tipping over.
This range can tip.
Injuries to persons can result.
Install anti-tip device packed with range.
See installation instructions.
DANGER
Electrical shock hazard.
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
4
5
Dimensions
Dimensions
Dual Fuel 30”, 36”, 48” and 60” W. Ranges
Dual Fuel 30”, 36”, 48” and 60” W. Ranges
28-1/16” (71.2 cm)
1-5/8”
(1560”
2.4
cm
)
(4.1 cm)
26-7/16” (67.2 cm)
47
-7
1” (2.5 cm)
(12 /8
1.6 ”
cm
)
8-1/8”
35
-7
(20.6 cm)
(91 /8
.1 ”
cm
)
29
35-7/8”
(75-7/8
.9 ”
cm
)
(91.1 cm) min.
to
37”
(94.0 cm) max.
1”
(2.
5
cm
)
3
(91 5-7
.1 /8”
cm
)
to min
.
(94 37
.0 ”
cm
)m
ax
.
Note: Unit shown with standard island trim.
19-3/8”
25-3/4” (65.4 cm)
(49.2 cm)
45-1/8” (114.6 cm)
24-5/16” (61.8 cm)
Note: Unit shown with standard island trim.
*A 3/4” (1.9 cm) standoff is included on each 48” and 60”W. VDSC model range and is
required for installation against a combustible wall. These standoffs can easily be removed if
installing against a non-combustible wall. (See instructions on page 24.)
6
7
Specifications
Specifications
Dual Fuel 30” and 36” W. Ranges
Dual Fuel 48” and 60” W. Ranges
Description
30” W. Models
36” W. Models
Description
48” W. Models
60” W. Models
Overall width
29-7/8”
(75.9 cm)
35-7/8”
(91.1 cm)
Overall width
47-7/8”
(121.6 cm)
60”
(152.4 cm)
Overall height
To top of side trim - 35-7/8” (91.1 cm) min. 37” (94.0 cm) max.
Legs adjust - 1-1/8” (2.9 cm)
Overall height
To top of side trim - 35-7/8” (91.1 cm) min. 37” (94.0 cm) max.
Legs adjust - 1-1/8” (2.9 cm)
Overall depth
from rear
To end of side panel - 24-5/16” (61.8 cm)
To front of door - 25-3/4” (65.4 cm)
To end of landing ledge - 28-1/16” (71.2 cm)
To end of door handle - 28-11/16” (72.9 cm)
Overall depth
from rear*
To end of side panel - 24-5/16” (61.8 cm)
To front of door - 25-3/4” (65.4 cm)
To end of landing ledge - 28-1/16” (71.2 cm)
To end of door handle - 28-11/16” (72.9 cm)
Additions to Base
Height
To top of island trim - add 1” (2.5 cm)
To top of backguard - add 8” (20.3 cm)
To top of high shelf - add 23-1/2” (59.7 cm)
Gas Requirements
Shipped Natural or LP/Propane, field convert with conversion kit (purchased separately);
accepts standard residential 1/2” (1.3 cm) ID gas service line
Gas Manifold Pressure
Natural 5.0” W.C.P./ Liquid Propane L/P 10.0” W.C.P.
Electrical Requirements
Max Amp Usage
See Electrical Requirements information.
240V - 25.4 amps
208V - 22.9 amps
Surface Burner Rating
Natural/LP
240V - 28.5 amps
208V - 24.7 amps
18,500 BTU (5.4 kW)/16,600 BTU (4.9 kW)
15,000 BTU (4.4 kW)/12,500 BTU (3.7 kW)
*Add 3/4” (1.9 cm) to overall depth for 48” and 60”W. VDSC models installed against a
combustible wall.
Additions to Base
Height
To top of island trim - add 1” (2.5 cm)
To top of backguard - add 8” (20.3 cm)
To top of high shelf - add 23-1/2” (59.7 cm)
Gas Requirements
Shipped Natural or LP/Propane, field convert with conversion kit (purchased separately);
accepts standard residential 1/2” (1.3 cm) ID gas service line
Gas Manifold Pressure
Electrical Requirements
Max Amp Usage
Natural 5.0” W.C.P./ Liquid Propane L/P 10.0” W.C.P.
See Electrical Requirements information.
240V - 37 amps
208V - 32 amps
240V - 40 amps
208V - 34.7 amps
Surface Burner Rating
Natural/LP
18,500 BTU (5.4 kW)/16,600 BTU (4.9 kW)
15,000 BTU (4.4 kW)/12,500 BTU (3.7 kW)
Griddle Burner Rating
NA
15,000 BTU Nat./12,500 BTU LP/Propane
(4.4 kW Nat/ 3.7 kW LP)
Griddle Burner Rating
15,000 BTU Nat./12,500 BTU LP/Propane
(4.4 kW Nat/ 3.7 kW LP)
Grill Burner Rating
NA
18,000 BTU Nat./16,000 BTU LP/Propane
(5.3 kW Nat/ 4.7 kW LP)
Grill Burner Rating
18,000 BTU Nat./16,000 BTU LP/Propane
(5.3 kW Nat/ 4.7 kW LP)
25-5/16” (64.6 cm)
30-5/16” (76.9 cm)
Oven(s) Interior Width
Oven(s) Interior Width
Right - 25-5/16” (64.6 cm)
Left - 13-3/4” (34.9 cm)
25-5/16” (64.6 cm)
Oven(s) Interior Height
16-1/2” (41.9 cm)
Oven(s) Interior Height
16-1/2” (41.9 cm)
Oven(s) Interior Depth
Overall - 19-1/2” (49.5 cm) AHAM 16-13/16” (42.7 cm)
Oven(s) Interior Depth
Overall - 19-1/2” (49.5 cm) AHAM 16-13/16” (42.7 cm)
Oven(s) Volume
Overall
AHAM
4.7 cu. ft.
4.1 cu. ft.
5.6 cu. ft.
4.9 cu. ft.
Oven(s) Volume
Overall
AHAM
Right - 4.7 cu. ft. Left - 2.6 cu. ft.
Right - 4.1 cu. ft. Left - 2.2 cu. ft.
Both Ovens 4.7 cu. ft.
Both Ovens 4.1 cu. ft.
Approximate
shipping weight
410 lbs.
(184.5 kg)
500 lbs.
(225 kg)
Approximate
shipping weight
575 lbs.
(258.8 kg)
750 lbs.
(337.5 kg)
Minimum clearances from adjacent combustible construction:
Below cooking surface (36” [91.4 cm] and below)
• Sides - 0”
• Top grate support - 36” (91.4 cm)
Above cooking surface (above 36” [91.4 cm])
• Sides - 6” (15.2 cm)
• Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7 cm)
above cooking surface
• Wall cabinets directly above product must be a minimum of 42” (106.7 cm) above cooking surface
• Rear - 0” with 8” backguard or high shelf; 0” with island trim and non-combustible rear wall;
• 6” (15.2 cm) with island trim and combustible rear wall
8
Minimum clearances from adjacent combustible construction:
Below cooking surface (36” [91.4 cm] and below)
• Sides - 0”
• Top grate support - 36” (91.4 cm)
Above cooking surface (above 36” [91.4 cm])
• Sides - 6” (15.2 cm)
• Within 6” (15.2 cm) side clearance, wall cabinets no deeper than 13” (33.0 cm) must be minimum 18” (45.7 cm)
above cooking surface
• Wall cabinets directly above product must be a minimum of 42” (106.7 cm) above cooking surface
• Rear - 0” with 8” backguard or high shelf; 0” with island trim and non-combustible rear wall;
• 6” (15.2 cm) with island trim and combustible rear wall
9
Clearance Dimensions
• This range may be installed directly
adjacent to existing 36” (91.4 cm) high
base cabinets.
Clearance Dimensions
(Proximity to Cabinets)
CAUTION
The bottom of a standard hood
should be 30” (76.2 cm) min. to
36” (91.4 cm) max. above the
countertop. This would typically
result in the bottom of the hood
being 66” (167.6 cm) to 72”
(182.9 cm) above the floor. Refer
to the range hood installation
instructions for additional
information. These dimensions
provide for safe and efficient
operation of the hood.
To prevent possible damage to cabinets
and cabinet finishes, use only materials
and finishes that will not discolor or
delaminate and will withstand temperatures
up to 194°F (90°C). Heat and moisture
resistant adhesive must be used if the
product is to be installed in laminated
cabinetry. Check with your builder or
cabinet supplier to make sure that the
materials meet these requirements.
IMPORTANT: The side trim MUST be
3/8” (.95 cm) above the adjacent base
cabinet countertop. This can be
accomplished by raising the unit using the
adjustment spindles on the legs.
• The range CANNOT be installed directly
adjacent to sidewalls, tall cabinets, tall
appliances, or other side vertical surfaces
above 36” (91.4 cm) high. There must be a
minimum of 6” (15.2 cm) sideclearance
from the range to such combustible
surfaces above the 36” (91.4 cm) counter
height.
(Wood/Composite Overlay)
Wo
od
/Co
Ov mpo
erl sit
ay e
”
24 cm)
.0
(61 or
66
(16 ”mi
7.6 n.
c
to m)
”
27 cm)
.6
(38
72
(18 ”ma
2.9 x.
cm
)
• Within the 6” (15.2 cm) side clearance to
combustible vertical surfaces above 36”
(91.4 cm), the maximum wall cabinet
depth must be 13” (33.0 cm) and wall
cabinets within this 6” (15.2 cm) side
clearance must be 18” (45.7 cm) above the
36” (91.4 cm) high countertop.
29
(75-7/8
.9 ”
cm
)
x.
a
m m)
”
c
3
1 3.0
(3
(
0” )
m
0c
30
(76”min
.2 .
cm
36 to )
”
m
(91 a
.4 x.
cm
)
Wo
od
/Co
Ov mpo
erl sit
ay e
in.
” m m)
42 6.7 c
6
”
0
(15 min (1
.2 .
cm
)
• Wall cabinets above the range must be a
minimum of 42” (106.7 cm) above the
range cooking surface for the full width of
the range. This minimum height
requirement does not apply if a range
hood is installed over the cooking surface.
in.
”m )
18 .7 cm
”
36 cm)
”
3/8 m)
.4
(91
(45
c
95
(0.
”
30 cm)
66
.2
(76
72
6” m)
.2 c
5
(1
(16 ”mi
7.6 n.
c
to m)
(18 ”ma
2.9 x.
c
m)
Wall Installation
30
(76”min
.2 .
cm
3 6 to )
”
(91 ma
.4 x.
cm
)
Note: Minimum clearance for back wall
is 0” with backguard or high-shelf.
CAUTION
Burn hazard.
To avoid risk of personal injury;
the use of cabinets for storage
above the appliance may result
in a potential burn hazard. Combustible
items may ignite, metallic items may
become hot and cause burns. If a cabinet
storage is to be provided the risk can be
reduced by installing a rangehood that
projects horizontally a minimum 5”
(12.7 cm) beyond the bottom of cabinets.
(op
en A
ing
wi d
th)
Note: Minimum clearance for
back wall is 0” with backguard
or high-shelf.
Range
“A”
Width
Dimension
30”
30” (76.2 cm)
36”
36” (91.4 cm)
48”
48” (121.9 cm)
60” 60-1/8” (152.7 cm)
Important: This range comes standard
with an Island Trim. There must be a
minimum of 6” clearance from rear of
range to a combustible wall or 0”
clearance to a non-combustible wall.
Island Installation
Note: If a range hood is installed, wall cabinets above the
range have a different minimum clearance height.
10
11
Electrical & Gas Requirements
Electrical & Gas Requirements
Electrical Requirements
Manual shut-off valve:
• On a dedicated circuit (no other
receptacles, switches or loads in the
circuit)
• Connected to a standard breaker of
appropriate size (GFI breaker of the same
size NOT recommended)
• Rated for Class A (5 mA +/- 1 mA trip
current) as per UL 943 standard
• In good condition and free from any
loose-fitting gaskets (if applicable in
outdoor situations)
• Protected from moisture (water, steam,
high humidity) as much as reasonably
possible
This product is manufactured with the
neutral terminal connected to the cabinet.
Use a 3-wire, agency approved, power
supply kit with closed loop terminals rated
per the National Electrical Code, ANSI/NFPA
70-latest edition (See Rating chart below). If
local codes prohibit grounding through the
neutral, use a 4-wire, agency approved,
power supply kit with closed loop terminals
rated per the National Electrical Code,
ANSI/NFPA 70-latest edition (See Rating
chart below).
RATING*
Specified Rating of Power
Supply Cord Kit and Circuit Protection
120/240 Volts
12.5 - 16.5 KW
16.5 - 17.5 KW
120/208 Volts
9.2 - 12.5 KW
12.5 - 13.5 KW
WARNING
Electrical shock hazard.
To avoid the risk of electrical
shock, personal injury or death;
verify electrical power is turned
off at the breaker box and gas supply is
turned off until the range is installed and
ready to operate, installation by an
authorized installer only.
Amps
40 or 50
50
*The National Electric Code calculation for
Electrical Load is less than the Total
Connected Electrical Load listed on the
model/serial rating plate.
Gas Connection
A GFI shall be used if required by NFPA70 (National Electric Code),
federal/state/local laws, or local
ordinances.
• The required use of a GFI is normally
related to the location of a receptacle with
respect to any significant sources of water
or moisture.
• Viking Range Corporation will NOT
warranty any problems resulting from GFI
outlets which are not installed properly or
do not meet the requirements below.
The gas supply (service) line must be the
same size or greater than the inlet line of the
appliance. This range uses a 1/2” (1.3 cm) ID
NPT (Sch40) inlet. Sealant on all pipe joints
must be resistive to LP gas.
Incoming line pressure upstream from the
regulator must be 1” W.C.P. higher than
the manifold pressure in order to check
the regulator. The regulator used on this
range can withstand a maximum input
pressure of 1/2” PSI (14.0” W.C.P.). If the
line pressure is in excess of that amount, a
step down regulator will be required.
The installer-supplied valve must be installed
in the gas service line before the appliance
in the gas stream and in a location where it
can be reached quickly in the event of
an emergency.
In Massachusetts: A “T” handle type
manual valve must be installed in the gas
supply line to the appliance.
• The appliance must be disconnected from
the gas supply piping system during any
pressure testing of that system.
IMPORTANT: Any conversion required
must be performed by your dealer or a
qualified licensed plumber or gas service
company.
Flexible Connections:
If the unit is to be installed with flexible
couplings and/or quick-disconnect fittings,
the installer must use a heavy-duty AGA
design-certified flexible connector of at least
1/2” (1.3 cm) ID NPT (with suitable strain
reliefs) in compliance with ANSI Z21.41
and Z21.69.
Please provide the service person with this
manual before work begins.
Pressure Regulator:
• All heavy-duty, commercial type cooking
equipment must have a pressure regulator
on the incoming service line for safe and
efficient operation, since service pressure
may fluctuate with local demand. External
regulators are not required on this range
since a regulator is built into each unit at
the factory. Under no condition bypass this
built-in regulator.
In Canada: CAN 1-6, 10-88 metal
connectors for gas appliances and CAN
1-6.9 M79 quick disconnect devices for use
with gas fuel.
In Massachusetts: This appliance must be
installed with a 36” (3-foot) long flexible
gas connector.
• Manifold pressure should be checked with
a manometer, natural gas requires 5.0”
W.C.P. and LP gas requires 10.0” W.C.P.
2-3/4”
(7.0 cm)
The range is designed specifically for
natural gas or liquid propane (LP) gas.
Before beginning installation verify that
the model is compatible with the intended
gas supply.
2” dia.
(5.1 cm)
Gas connection
in this area
2-1/2”
If the use of a GFI is required, it should be:
• Of the receptacle type (breaker type or
portable type NOT recommended)
• Used with permanent wiring only
(temporary or portable wiring NOT
recommended)
(6.4 cm)
1-3/4”
23-7/16”
(59.5 cm)
(78.9 cm)
28-5/16”
(71.9 cm)
(4.4 cm)
Gas or electrical
connection in
this area
4-3/8”
(11.1 cm)
12
31-1/16”
13
General Information
Installation
NOTICE
READ AND FOLLOW ALL WARNING
AND CAUTION INFORMATION WHEN
INSTALLING THIS APPLIANCE.
Remove and discard all packing materials,
including cardboard and tape on the outside
and inside of the range.
DO NOT use the handle or oven door to
lift the oven. Remove door before
installation to ensure that it is not used to
lift the unit. DO NOT lift or carry the door
by the handle.
Remove the burner grates and styrofoam
off the top cooking surface. Be sure to
remove the burner caps packaged in
styrofoam below the burner grates.
Removing the door must be done by your
dealer, a qualified licensed plumber, or
certified gas installer.
Moving, Handling, and Unpacking
• All openings in the wall behind the
appliance and in the floor under the
appliance must be sealed.
• Do not obstruct the flow of combustion and
ventilation air.
Do not discard the anti-tip metal
bracket supplied with the range.
This is the anti-tip device and must
be installed with the unit. Refer to
“Anti-tip Device Installation”
section.
CAUTION
Avoid any damage to oven vents. The vents
need to be unobstructed and open to provide
proper airflow for optimal oven performance.
CAUTION
Door Removal
1
2
Some stainless steel parts may have a plastic
protective wrap which must be peeled off.
The interior should be washed thoroughly
with hot, soapy water to remove film
residues and any dust or debris before being
used, then rinsed and wiped dry. Solutions
stronger than soap and water are rarely
needed.
The cooling fan should be operating when
the unit is in operation. If you notice the
cooling fan is not operating or you observe
unusual or excessive noise coming from the
cooling fan, contact a Viking Authorized
Service Center before continuing operation.
Failure to do so can result in damage to the
oven or surrounding cabinets.
Open door completely. Place pins, supplied with unit, in
pin hole. For personal safety, ONLY use pins
supplied with the unit.
Remove hinge trim screws. Take off hinge trim. Identify
right and left hinge for future re-installation.
3
4
Close until pins stop door.
14
Lift door up and out.
15
Leg Installation
Electrical Connection (3-wire)
Note: If you have a 4-wire connection, see following section for
4-wire connection instructions.
2
1
WARNING
WARNING
Electrical shock hazard.
Electrical shock hazard.
1
1
3
2
Note: It is strongly recommended
that a pallet or lift jack be used rather than tilting.
Raise unit about a foot. Unscrew temporary legs from
couplings.
Legs are packed in styrofoam top pack.
Note: Legs should be installed near to where
appliance is to be used, as they are
not secure for long transit.
4
3
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
To avoid risk or electrical
shock, personal injury or death;
grounding product to the frame
of the unit may or may not be permitted
through your local codes. If ground to the
frame is not permitted then a 4 conductor
power cord must be used.
See Electrical Requirements information.
1
Where local codes do not permit grounding
through neutral, use a 4-wire power supply
cord. The cord or conduit must be secured
to the range with the strain relief bracket.
The electrical connection is made at the
terminal block, which is located behind the
access door on the back of the range.
Screw legs into couplings on all
four corners.
Lower range gently to keep any undue strain from
legs and internal mounting hardware.
Note: VDSC560 ranges contain two access
doors and terminal blocks. Either location
can be used for the power supply
dependent on the receptacle location or
length of power supply wiring.
Remove access door.
3
2
Remove supply cord strain relief
bracket and three supply cord mounting screws
on terminal block.
16
Feed supply cord up through hole in bottom
of range back.
17
Electrical Connection (3-wire) (cont.)
5
4
Electrical Connection (4-wire)
1
WARNING
WARNING
Electrical shock hazard.
Electrical shock hazard.
Push supply cord toward terminal
block to relieve strain, reattach supply cord strain relief
bracket over supply cord.
Attach line #1 (red) and line #2 (black)
leads to outside terminal. Attach neutral wire (white)
to center terminal on the terminal block.
To avoid risk of electrical shock,
personal injury or death; verify
your appliance has been
properly grounded in accordance with
local codes or in absence of codes, with
the National Electrical Code (NEC).
ANSI/NFPA 70-latest edition.
To avoid risk or electrical
shock, personal injury or death;
grounding product to the frame
of the unit may or may not be permitted
through your local codes. If ground to the
frame is not permitted then a 4 conductor
power cord must be used.
See Electrical Requirements information.
6
1
Where local codes do not permit grounding
through neutral, use a 4-wire power supply
cord. The cord or conduit must be secured
to the range with the strain relief bracket.
The electrical connection is made at the
terminal block, which is located behind the
access door on the back of the range.
Note: VDSC560 ranges contain two access
doors and terminal blocks. Either location
can be used for the power supply
dependent on the receptacle location or
length of power supply wiring.
Reattach access door.
Remove access door.
3
2
Remove supply cord strain relief
bracket and three supply cord mounting screws on
the terminal block.
18
Remove grounding screw. Cut-off
and discard ground strap.
19
Electrical Connection (4-wire) (cont.)
Leveling/Adjustments/Alignment
Feed supply cord up through hole in bottom
of range back.
Attach ground lead (green)
with ground screw that was removed.
6
7
2
1
5
4
1
Measure the four corners in cutout area to verify if
flooring is level.
For uneven or sloped floors, level unit with metal shims
only, as the adjustment required may exceed
the thread available in the leg.
4
3
”
3/8cm)
95
(0.
Attach line #1 (red) and line #2 (black)
leads to outside terminal. Attach neutral wire (white) to
center terminal on terminal block.
Push supply cord toward terminal
block to relieve strain, reattach supply cord strain
relief bracket over supply cord.
Check that unit is level side to
side and front to back. Side trim of the high corner
must be 3/8” (0.95 cm) above countertop.
Move unit into opening.
6
5
8
1
1
2
If leveling is required, move unit out of opening.
Reattach access door.
20
Lift unit and prop on wood blocks.
21
Anti-tip Device Installation (cont.)
Leveling/Adjustments/Alignments (cont.)
7
Set the high corner of range so that the top of side trim is
3/8” (0.95 cm) above countertop. Level range to high corner.
Attach bracket with
mounting hardware provided.
Mark and drill holes where bracket will be located.
Connecting Gas & Electric
Anti-tip Device Installation
1
WARNING
DANGER
Gas leak hazard.
Tipping hazard.
To reduce the risk of property
damage or personal injury;
install anti-tipping device
provided in accordance with
the installation instructions
in this document. Device
must be engaged properly to
prevent product from tipping
over.
2
4
3
Me
as
ure
me
nt
(A
)
Measure from floor to bottom
of the anti-tip opening located on the back of range.
This will be measurement (A).
To avoid risk of personal injury
or death; leak testing of the
appliance must be conducted
according to the manufacturer’s
instructions. Before placing appliance in
operation, always check for gas leaks
with soapy water solution.
• DO NOT USE AN OPEN FLAME TO
CHECK FOR GAS LEAKS.
Note: Refer to electrical and gas
requirements section for proper
installation information.
Y
X
)
(A
nt )
e
m
rem c
su ” (1.3
a
Me 1/2
+
Range
Width
“X”
Dimension
“Y”
Dimension
30”
3-5/8” (9.2 cm)
N/A
36”
8” (20.3 cm)
N/A
48”
5” (12.7 cm)
N/A
60”
5” (12.7 cm) 24-7/8” (63.2 cm)
1
Anti-tip location for each range width.
Locate anti-tip bracket on rear wall with the top left
corner at measurement (A) plus 1/2” (1.3 cm) from the
floor and “X” dimension (see chart) from where the
right side of range (facing range) is to be located and
“Y” dimension (see chart) from where the left side of
the range (facing range) is to be located.
Connect gas and electrical. Before placing appliance in operation,
always check for gas leaks. This must be performed by your
dealer, a qualified licensed plumber, or gas service company.
22
23
Standoff Bracket Removal (48” and 60”W. VDSC Models Only)
Note: Standoff brackets can only be removed if range is installed against a NON-COMBUSTIBLE wall.
1
Door Replacement and Adjustment
2
1
DANGER
FIRE HAZARD
Standoff brackets provide a
3/4” barrier between back of
range and rear wall. These
must be in place for adequate ventilation.
The standoff brackets may only be
removed if range is installed against a
non-combustible wall.
Reattach door to range.
Unscrew four standoff brackets and remove.
Open door completely. Reattach hinge trim.
Final Installation
2
1
Slide range into place. Be sure
anit-tip bracket slides into the anit-tip opening.
Burner caps are packed in styrofoam top pack with the
grates. Place burner on top of range. Place burner
grate on top of burner cap and grate support.
Note: Arrow on burner cap must be pointing towards
back of range.
3
3
4
Remove pins from holes in hinges.
Close door.
5
”
3/8cm)
95
(0.
If the door needs to be adjusted, loosen hinge trim screws located in
step 2. Adjust the screws located between the door and kickplate using a
5/32” hex head allen wrench. After adjustment, tighten hinge trim screws.
Check that unit is level side to side
and front to back. The side trim must be 3/8” (0.95 cm)
above countertop. If unit is not level repeat steps 5-7
of “Leveling/Adjustments/Alignment” section.
24
25
Service & Registration
Final Preparation
• All stainless steel body parts should be
wiped with hot, soapy water and with a
liquid cleaner designed for this material.
If buildup occurs, DO NOT use steel wool,
abrasive cloths, cleansers, or powders!
If it is necessary to scrape stainless steel
to remove encrusted materials, soak with
hot, wet cloths to loosen the material, then
use a wool or nylon scraper. DO NOT use
a metal knife, spatula, or any other
material tool to scrape stainless steel!
Scratches are almost impossible to
remove.
Performance Checklist
A qualified installer should carry out the
following checks:
h Check top burner
1-1/2”
ignition. See
(3.8 cm)
drawing for proper
flame height on HI.
The low flame should
light at every port.
h Check self-clean function—door will lock in
approximately 30 seconds, the center and
outside broil elements will turn on and the
bake element will turn on at partial power.
Check broil elements through window to
make sure they are on, then abort
self-clean cycle to unlock door.
3/8”
Only authorized replacement parts may be used in performing service on the appliance.
All servicing should be referred to a qualified technician.
Contact Viking Range Corporation, 1-888-VIKING1 (845-4641), for the nearest service parts
distributor in your area or write to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
Record the following information indicated below. You will need it if
service is ever required. The serial number and model number for your
appliance can be found by opening the door and looking under the
control panel. A duplicate label is located on the back side of the
range.
(0.95 cm)
NOTICE
When conducting performance test,
DO NOT run self-clean cycle for more
than 10 minutes with oven racks inside
oven. This could cause them to discolor
due to the high temperature required
for self-cleaning.
h Check oven bake function—bake element
on full power, center and outside broil
elements at partial power.
h Convection bake function—bake and broil
elements the same with the convection fan
on.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
h Check TruConvec™ function—TruConvec
element (behind convection fan cover) on
and convection fan on.
Dealer's name _____________________________________________________________________________________
Address ___________________________________________________________________________________________
h Check HI broil function–both broil
elements at full power.
These installation instructions should remain with the unit
for future reference.
h Check LOW broil function—inner broil
element only.
h Check convection broil function—both
broil elements at full power with convection
fan on.
26
27
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement