advertisement
Document # PG05-006
DR30D, DR30DH, DR30DI, DR30DIH
Distinctive
™
30” Wide
Dual Fuel Range
Revised 06/13/13 Page 1/7
PLANNING
GUIDE
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated.
46 3/8” (117.8 cm)
28 7/8” (73.3 cm)
28 1/2” (72.4 cm)
26 1/2” (67.3 cm)
24 3/8” (61.9 cm)
1 1/8” (2.9 cm)
Front of open door
Front of handle
Front of knobs
Control panel
Rear of control panel/oven door
warNINg
• Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information.
• This appliance must be installed in accordance with the accompanying installation instructions.
External handle shown, some models have integral handle
(see inside cover)
Width at front panel:
29 7/8” (75.9 cm)
9” (22.9 cm)
Backguard**
1 1/8” (2.9 cm) to cooking surface (top of grates) from top of trim
Full size side panel
3” (7.7 cm)
Backguard*
6” (15.2 cm)
Backguard**
35 3/4”
(90.8 cm) to
37 7/8”
(96.2 cm)
* Standard
** Optional
Optional Backguard and Island Trim Part Numbers
Description Part Number
Island trim kit (no backguard) ADTK30D
6 inch trim kit
9 inch trim kit
ADB3006
ADB3009
NOTE: Model DR30D[H] is NOT designed for self-rimming installation or installation with a raised vent.
PRoDUct DImENsIoNs - moDEL DR30D[H] (FREEstANDING moDEL)
External handle shown, some models have integral handle
(see inside cover)
Width at front panel:
29 7/8” (75.9 cm)
46 3/16” (117.3 cm)
28 11/16” (72.9 cm)
28 5/16” (71.9 cm)
26 5/16” (66.8 cm)
24 3/16” (61.4 cm)
1” (2.5 cm)
Front of open door
Front of handle
Front of knobs
Control panel
Rear of control panel/oven door
Rear trim overhang
5/16” (8 mm)
Trim thickness
1 7/16” (3.7 cm) to cooking surface (top of grates) from bottom of trim
35 7/16”
(90.0 cm) to
37 9/16”
(95.4 cm)
3 1/4” (8.3 cm)
Removable side panel
NOTES:
■ When installing model DR30DI[H] with a raised vent, install
only Dacor model ERV3015.
■ The backguards shown above for model DR30D[H] are NOT compatible with model DR30DI[H].
■ This model can be installed in a freestanding configuration between cabinets, provided the countertop is as high at the trim around the cooktop.
PRoDUct DImENsIoNs - moDEL DR30DI[H] (sELF-RImmING moDEL)
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
Document # PG05-006
DR30D, DR30DH, DR30DI, DR30DIH
Distinctive 30” Wide
Dual Fuel Range
Revised 06/13/13 Page 2/7
PLANNING
GUIDE
gas and Electrical requirements
gas Type
Natural gas gas Supply Pressure requirements*
Manifold Pressure
5” water column
Minimum gas Supply
Pressure
6” water column
LP 10” water column 11” water column
* Maximum input gas supply pressure for all models is 1/2 psi
The regulator inlet accommodates a 3/4” gas line. The range ships with a
1/2” to 3/4” adapter connected to the regulator.
Gas inlet
Range electrical access, cover removed
B
Electrical Specifications
Circuit required Total Connected Load
240 Vac, 60 Hz., 30 Amp.* 5.7 kW (23.8 Amp.)
* Two 120 Vac hot (L1 and L2), one neutral, one ground
D
A
C
7/8" to 1 1/8" dia. access hole connection hole in bottom*
■
■
The ratings above are for reference only - refer to the range's product data label for exact specifications.
The correct voltage, frequency and amperage must be supplied to the appliance from a separate, grounded, circuit that is protected by a properly sized circuit breaker or time delay fuse. If a time-delay fuse is utilized, fuse both sides of the line (L1 and L2).
ranges equipped for installation in Canada:
■ Freestanding ranges used in Canada require a factory installed 4-wire appliance cord and
NEMA 14-50P plug. Order model number
DR30D-C or DR30DH-C. The appliance cord is
66 inch (168 cm) long.
■ Do not modify the factory wiring. The plug is designed to plug directly into a NEMA 14-50R electrical receptacle installed by a licensed electrician.
NEmA 14-50R
REcEPtAcLE
■
■ all other models:
The wiring needs to be long enough to allow the range to be pulled out for service, while remaining connected (see following page).
The wiring connected to the range must:
■
■
■
Meet NEMA standards and have a minimum rating of 250 Volts @ 30
Amp.
Include a strain relief.
Be terminated by tinned leads, closed loop terminals or open ended spade lugs with upturned ends.
■ Connect to a junction box or receptacle installed by a licensed electrician.
Where local code permits, a 3 or 4 wire appliance cord may be used. It must:
Be UL listed type SRD or SRDT.
Be equipped with a NEMA 14-50P 4-wire plug or, where local code permits, a NEMA 10-50P 3-wire plug.
a
4 3/4”
(12.1 cm)
B
22 1/8”
(56.2 cm)
C
8 3/4”
(22.2 cm)
D
13 3/4”
(34.9 cm)
GAs AND ELEctRIcAL DImENsIoNs
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
Document # PG05-006
DR30D, DR30DH, DR30DI, DR30DIH
Distinctive 30” Wide
Dual Fuel Range
Revised 06/13/13 Page 3/7
PLANNING
GUIDE
Cabinet Layout
■ Carefully check the location where the range is to be installed. For best performance, the range should be placed away from drafts that may be caused by doors, windows and heating and air conditioning outlets.
■
■
To reduce the risk of personal injury and to reduce accumulated smoke in the room, Dacor strongly recommends installing a range hood or raised vent (model DR30DI[H] only). A range hood should project horizontally a minimum of five (5) inches beyond the face of the cabinets.
All maximum and minimum dimensions and clearances shown in the diagram below must be maintained for safe operation.
■
■
Any openings in the wall behind the appliance or in the floor underneath it must be sealed.
Carefully note the requirements stated below for clearances to walls and cabinets.
Cabinet tolerances: -1/16”, (+1.6 mm) -0
E gas and Electrical Service
■ The shaded area shown below denotes the location of the gas inlet and the electrical junction box/receptacle. This is the recommended location. For replacement purposes, the location of the existing utilities may be utilized provided they do not interfere with the sides or rear of the range. Check local building codes for permissible gas valve locations.
■ An external manual shut-off valve must be installed between the gas inlet and the range for the purpose of turning on or shutting off gas to the appliance.
The installation must allow for the following:
■ Access to the gas shut-off valve when the unit is installed.
■
■
■
Access to the remote circuit breaker panel/fuse box when the range is in place.
The gas supply piping, gas shut-off valve and the electrical junction box or receptacle must be located so they do not interfere with the range when it is installed.
The junction box and gas shut off valve must be located so that the range can be pulled out for service while the appliance remains connected.
10” min. (25.4 cm) to any combustibles above counter both sides
Non-combustible rear wall recommended
13” (33.0 cm) max.
5
Back wall 1
24 3/8” min.
(61.9 cm)
F
Cabinet face below countertop
18” (45.7 cm) min.
2, 5
30” (76.2 cm) min.
2
F
10” (25.4 cm) min.
to combustible side walls above the range
(both sides)
Countertop front cUtoUt FoR moDEL DR30D[H]
WItH sELF-RImmING tRIm KIt
PN AtKDR30DW-01
Note 6
Note 3
REqUIRED cAbINEt
DImENsIoNs
Suggested location of utilities 4
1 Minimum distance to a combustible rear wall for model
DR30DI[H] is 2.5” (6.4 cm) from top rear trim. Model DR30D[H] may be installed flush to rear wall, but non-combusible surface or 9-inch backguard (PNADB3009) is recommended.
2 Distance to combustible surfaces measured from cooking surface (top of cooktop grate); if installing an overhead range hood, also check the hood specifications for minimum required clearances.
3 Cabinet/countertop depth is at discretion of customer but cabinet face MUST NOT protrude further than rear of cabinet front, see Product Dimensions.
4
5
Consult local code for exact location requirements.
This specification does not apply for cabinets located greater than a horizontal distance of 10” (25.4 cm) from the edge of the range.
6 Model DR30D[H]: 37 7/8 (96.2 cm) max.
Model DR30DI[H]: 37 7/16 (95.1 cm) max.
All specifications subject to change without notice.
www.dacor.com
E
Cutout Dimensions
36” (91.4 cm)*
30” (76.2 cm)**
30 1 /
16
F***
” (91.6 cm)
* Recommended ** Minimum
*** See following page for model DR30DI[H]
Phone: (800) 793-0093
Document # PG05-006
DR30D, DR30DH, DR30DI, DR30DIH
Distinctive 30” Wide
Dual Fuel Range
Revised 06/13/13 Page 4/7
PLANNING
GUIDE
Model Dr30DI[H] Self-rimming Installation without raised Vent
■ See pages 5/7 - 7/7 for raised vent installations.
■
■
Self-rimming installations create a “built-in” look where the trim of the range overlaps the surrounding countertop. It is also possible, if the cabinets are the right depth, to self rim the front of the range into the cabinet face, immediately behind the control panel and door trim.
When the front of the range is self-rimmed, the 3 1/4” side panels are removed.
It is not possible to self-rim the front of the range with countertop cutouts that are 30 inches wide.
Cabinet tolerances: -1/16”, (+1.6 mm) -0
Model Dr30DI[H] range with
H J K
Option 1
21”
(53.3 cm)
0” (0 cm) to
3 1/4” (8.3 cm)
0” (0 cm) to
5 3/8” (13.7 cm)
Option 2 1
24 1/4”
(61.6 cm)
NA
1 Side panels removed
Countertop height for all self-rimming installations:
35 7/16” (90.0 cm) minimum, 37 7/16” (95.1 cm) maximum
0” (0 cm) to
2 1/8” (5.4 cm) oPtIoN 1: cUstom coUNtERtoP/stANDARD cAbINEt, toP sELF-
RImmED oNLy, 3 1/4 INcH sIDE PANELs Not REmovED
Rear wall or other vertical surface **
10” min.
(25.4 cm) both sides
1/4” min.* (6 mm)
countertop overhang oPtIoN 2: cUstom coUNtERtoP AND cAbINEt, toP AND FRoNt sELF-RImmED, 3 1/4 INcH sIDE PANELs REmovED
Rear wall or other vertical surface **
10” min.
(25.4 cm) both sides
1/4” min.* (6 mm)
countertop overhang
29 1/4” (74.3 cm) countertop opening
30” (76.2 cm) below countertop
H
J K toP vIEW overhang to width of cabinets below
To cabinet face below countertop
To countertop
front
* When increasing overhang, increase dimension H by same amount.
** Any vertical surfaces behind the range must be non-combustible unless countertop overhang exceeds 2 3/4” (7.0 cm).
Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm)
Combustible side wall above range
29 1/4” (74.3 cm) countertop and cabinet opening
H
K
Notch countertop to
30” (76.2 cm) toP vIEW
Cabinet face below countertop
To countertop
front
* When increasing overhang, increase dimension H by same amount.
** Any vertical surfaces behind the range must be non-combustible unless countertop overhang exceeds 2 3/4” (7.0 cm).
Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm)
See Top View for required distance to vertical surfaces
1/4” min. (6.4 mm) flat countertop min.
Range trim resting on countertop
See Top View for required distance to vertical surfaces
1/4” min. (6.4 mm) flat countertop min.
Range trim resting on countertop
Back of cutout
H
Countertop
Cabinet face
Back of control panel
3 1/4 inch side panel
DR30DI[H] range
sIDE vIEW
Back of cutout
H
Countertop
DR30DI[H] range
Range side panels removed
Cabinet face
Back of control panel and trim behind door rest against cabinet face sIDE vIEW
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
Document # PG05-006
23 15/16” min.
(60.8 cm)
Countertop
front toP vIEW
DR30D, DR30DH, DR30DI, DR30DIH
Distinctive 30” Wide
Dual Fuel Range
Revised 06/13/13 Page 5/7
PLANNING
GUIDE
Model Dr30DI[H] Self-rimming Installation without raised Vent (cont.)
.
oPtIoN 3: stANDARD coUNtERtoP AND cAbINEt, toP sELF-RImmED oNLy, 3 1/4 INcH sIDE PANELs Not
REmovED - AtKDR30DW-02 tRIm KIt REqUIRED
Cabinet tolerances: -1/16”, (+1.6 mm) -0
10” min. (25.4 cm) to any combustibles above counter both sides
Back of cutout
Non-combustible rear wall required*
5/8” min. (1.6 cm) countertop overhang in back
30” (76.2 cm) countertop/cabinet opening
Cabinet face below countertop
* Range trim overhangs countertop 9/16” in back. Rear wall must be noncombustible unless the rear wall is 2 1/2”
(6.4 cm) or more from range rear trim.
See Top View for required distance to vertical surfaces
1/4” min. (6.4 mm) flat countertop min.
Range trim resting on countertop
H
Countertop
Cabinet face
Back of control panel
3 1/4 inch side panel
Dr30DI[H] Self-rimming Installation with raised Vent
■ Only model DR30DI[H] may be installed with a raised vent. Use only
Dacor raised vent model ERV3015.
■ A self-rimming countertop configuration is required for raised vent installation. self-rimming installation of the range and raised vent create a “built-in” look where the range trim overlaps the countertop on both sides and the raised vent overlaps the countertop in back. It is also possible, if the cabinets are deep enough, to self rim the front portion of the range into the cabinet face immediately behind the control panel and door trim or behind the side panels. The rear range trim will partially cover the front of the raised vent chassis in back.
H
20 5/8”
(52.4 cm)
J
0” (0 cm) to
3 1/4” (8.3 cm)
K
0” (0 cm) to
5 3/8” (13.7 cm) oPtIoN 1: RANGE/RAIsED vENt combINAtIoN WItH cUstom coUNtERtoP/stANDARD cAbINEt, toP sELF-
RImmED oNLy, 3 1/4 INcH sIDE PANELs Not REmovED
Non-combustible rear wall recommended
10” min.
(25.4 cm) both sides
3/8” min. (1.0 cm) countertop overhang
27 1/2” (69.9 cm) raised vent opening
29 1/4” (74 3 cm) countertop opening
30” (76.2 cm) cabinet opening below countertop
Combustible side wall above range
H
2 9/16”
(6.5 cm)
J K toP vIEW overhang to width of cabinets
To cabinet face below countertop
To countertop
front
Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm)
28 11/16” (72.9 cm)
3/8” min. (1.0 cm) flat countertop overhang required behind cutout
Range trim resting on countertop
Cabinet face
DR30DI[H] range
H
Countertop
DR30DI[H] range
Back of control panel
3 1/4 inch side panel sIDE vIEW
3/8” min. (1.0 cm) space required behind ERV3015 chassis to clear stiffener sIDE vIEW
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
Document # PG05-006
DR30D, DR30DH, DR30DI, DR30DIH
Distinctive 30” Wide
Dual Fuel Range
Revised 06/13/13 Page 6/7
PLANNING
GUIDE
Dr30DI[H] Self-rimming Installation with raised Vent
(cont.)
oPtIoN 2: RANGE/RAIsED vENt combINAtIoN WItH cUstom coUNtERtoP AND cAbINEt, toP AND FRoNt sELF-RImmED, 3 1/4 INcH sIDE PANELs Not REmovED
Cabinet tolerances: -1/16”, (+1.6 mm) -0 oPtIoN 3: RANGE/RAIsED vENt combINAtIoN cUstom coUNtERtoP AND cAbINEt, toP AND FRoNt sELF-RImmED, 3 1/4 INcH sIDE PANELs REmovED
Cabinet tolerances: -1/16”, (+1.6 mm) -0
H
20 5/8” *
(52.4 cm)
K
0” (0 cm) to
5 3/8” (13.7 cm)
* Cabinet face below countertop must
be flush with back of notch in countertop
H
23 7/8” *
(60.6 cm)
K
0” (0 cm) to
2 1/8” (5.4 cm)
* Cabinet face below countertop must
be flush with back of notch in countertop
Non-combustible rear wall recommended
10” min.
(25.4 cm) both sides
3/8” min. (1.0 cm) countertop overhang
27 1/2” (69.9 cm) raised vent opening
29 1/4” (74 3 cm) countertop and cabinet opening
2 9/16”
(6.5 cm)
H
Combustible side wall above range
K
Notch countertop to
30” (76.2 cm) toP vIEW
Cabinet face below countertop
To countertop
front
Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm)
28 11/16” (72.9 cm)
3/8” min. (1.0 cm) flat countertop overhang required behind cutout
H
Countertop
DR30DI[H] range
Range trim resting on countertop
Cabinet face
Back of side panel rests against cabinet face
3 1/4 inch side panel
ERV3015 raised vent
3/8” min. (1.0 cm) space required behind ERV3015 chassis to clear stiffener sIDE vIEW
Non-combustible rear wall recommended
10” min.
(25.4 cm) both sides
27 1/2” (69.9 cm) raised vent opening
29 1/4” (74 3 cm) countertop and cabinet opening
3/8” min. (1.0 cm) countertop overhang
2 9/16”
(6.5 cm)
H
Combustible side wall above range
K
Notch countertop to
30” (76.2 cm) toP vIEW
Cabinet face below countertop
To countertop
front
Countertop height: min: 35 7/16” (90.0 cm) max: 37 7/16” (95.1 cm)
28 11/16” (72.9 cm)
3/8” min. (1.0 cm) flat countertop overhang required behind cutout
Range trim resting on countertop
Countertop
H
DR30DI[H] range
ERV3015 raised vent
3/8” min. (1.0 cm) space required behind ERV3015 chassis to clear stiffener
Range side panel removed
Cabinet face
Back of control panel and trim behind door rest against cabinet face sIDE vIEW
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
Document # PG05-006
DR30D, DR30DH, DR30DI, DR30DIH
Distinctive 30” Wide
Dual Fuel Range
Revised 06/13/13 Page 7/7
PLANNING
GUIDE
Model Dr30DI[H] Self-rimming Installation without raised Vent (cont.)
.
oPtIoN 4: RANGE/RAIsED vENt combINAtIoN WItH stANDARD coUNtERtoP AND cAbINEt, toP sELF-
RImmED oNLy, 3 1/4 INcH sIDE PANELs Not REmovED,
AtKDR30DW-03 tRIm KIt REqUIRED
Cabinet tolerances: -1/16”, (+1.6 mm) -0
Countertop height for all self-rimming installations:
35 7/16” (90.0 cm) minimum, 37 7/16” (95.1 cm) maximum
10” min.
(25.4 cm) both sides
Non-combustible rear wall recommended
27 1/2” (69.9 cm) raised vent countertop opening
3/8” min. (1.0 cm) countertop overhang
2 9/16”
(6.5 cm)
30” (76.2 cm) countertop/cabinet opening
24 1/8” min.
(61.3 cm)
Cabinet face below countertop
Countertop front
28 11/16” (72.9 cm)
3/8” min. (1.0 cm) flat countertop overhang required behind cutout
H
Countertop
DR30DI[H] range
Range trim resting on countertop
Cabinet face
Back of control panel
3 1/4 inch side panel
3/8” min. (1.0 cm) space required behind ERV3015 chassis to clear stiffener
All specifications subject to change without notice.
www.dacor.com
Phone: (800) 793-0093
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project