Yamaha YJ125T Operating instructions

Yamaha YJ125T Operating instructions
1
2
3
4
5
6
OWNER’S MANUAL7
8
9
YJ125T
LIT-11626-18-39
5YR-F8199-11cv.pmd
5YR-F8199-11
3
2004/06/11, 14:14
1
2
3
EAU10041
4
5
6
7
8
9
5YR-F8199-11ch0.pmd
1
2004/06/11, 14:11
EAU10050
INTRODUCTION
EAU10090
Congratulations on your purchase of the Yamaha VINO125. This model is the result of Yamaha’s vast experience in the
production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and
reliability that have made Yamaha a leader in these fields.
1
This manual will give you an understanding of the operation, inspection, and basic maintenance of this scooter. If you have
any questions concerning the operation or maintenance of your scooter, please consult a Yamaha dealer.
The design and manufacture of this Yamaha scooter fully comply with the emissions standards for clean air applicable at the
date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the
scooter. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the
recommended maintenance schedules and operating instructions contained within this manual.
2
3
4
5
6
7
8
9
5YR-F8199-11ch0.pmd
2
2004/06/11, 14:11
EAU10120
IMPORTANT MANUAL INFORMATION
EAU34110
Particularly important information is distinguished in this manual by the following notations:
1
2
Q
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
w
Failure to follow WARNING instructions could result in severe injury or death to the scooter
operator, a bystander, or a person inspecting or repairing the scooter.
cC
A CAUTION indicates special precautions that must be taken to avoid damage to the scooter.
NOTE:
A NOTE provides key information to make procedures easier or clearer.
3
4
5
6
7
8
NOTE:
8 This manual should be considered a permanent part of this scooter and should remain with it even if the scooter is
subsequently sold.
8 Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most
current product information available at the time of printing, there may be minor discrepancies between your scooter and
this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.
9
EWA12410
w
PLEASE READ THIS MANUAL CAREFULLY AND COMPLETELY BEFORE OPERATING THIS SCOOTER.
5YR-F8199-11ch0.pmd
3
2004/06/11, 14:11
IMPORTANT MANUAL INFORMATION
EAU10192
1
2
AFFIX DEALER
3
LABEL HERE
4
5
6
VINO125
OWNER’S MANUAL
©2004 by Yamaha Motor Taiwan Co., Ltd.
1st edition, June2004
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Taiwan Co., Ltd.
is expressly prohibited.
Printed in Taiwan.
P/N LIT-11626-18-39
5YR-F8199-11ch0.pmd
4
2004/06/11, 14:11
7
8
9
EAU10210
TABLE OF CONTENTS
1
2
3
4
5
6
7
8
9
SAFETY INFORMATION ....... 1-1
Further safe-riding points ..... 1-5
Location of important labels .. 1-6
DESCRIPTION ....................... 2-1
Left view ............................... 2-1
Right view ............................. 2-2
Controls and instruments ..... 2-3
INSTRUMENT AND CONTROL
FUNCTIONS........................... 3-1
Main switch/steering lock ..... 3-1
Indicator lights ...................... 3-2
Handlebar switches .............. 3-2
Speedometer unit ................. 3-3
Fuel gauge ............................ 3-3
Front brake lever .................. 3-3
Rear brake lever ................... 3-4
Fuel tank cap ........................ 3-4
Fuel ...................................... 3-5
Catalytic converter ............... 3-5
Kickstarter ............................ 3-6
Seat ...................................... 3-6
Helmet holder ....................... 3-6
Storage compartment ........... 3-7
Luggage hook ....................... 3-8
Carrier .................................. 3-8
Sidestand ............................. 3-8
5YR-F8199-11ch0.pmd
5
Ignition circuit cut-off system 3-9
PRE-OPERATION CHECKS . 4-1
Pre-operation check list ........ 4-2
OPERATION AND IMPORTANT
RIDING POINTS .................... 5-1
Starting a cold engine ........... 5-1
Starting off ............................ 5-2
Acceleration and
deceleration ....................... 5-2
Braking ................................. 5-3
Engine break-in .................... 5-3
Parking ................................. 5-4
PERIODIC MAINTENANCE
AND MINOR REPAIR ............ 6-1
PERIODIC MAINTENANCE 6-1
Owner’s tool kit ..................... 6-1
Periodic maintenance chart for
the emission control
system ............................... 6-2
General maintenance and
lubrication chart ................. 6-3
Removing and installing
panels ................................ 6-6
Checking the spark plug ....... 6-7
Air filter and V-belt case air filter
elements ............................ 6-8
Replacing the tail/brake light
bulb .................................. 6-11
Replacing a turn signal light
bulb .................................. 6-11
Checking the front brake pads
and rear brake shoes ...... 6-12
Checking the brake fluid
level ................................. 6-13
Changing the brake fluid ..... 6-13
Checking and lubricating the
cables .............................. 6-14
Checking and lubricating the
throttle grip and cable ...... 6-14
Lubricating the front and rear
brake levers ..................... 6-14
Checking and lubricating the
centerstand and
sidestand ......................... 6-15
Checking the front fork ....... 6-15
Checking the steering ........ 6-16
Replacing the headlight
bulb .................................. 6-16
Final transmission oil .......... 6-17
Adjusting the carburetor ..... 6-19
Adjusting the throttle cable free
play .................................. 6-19
2004/06/11, 14:11
TABLE OF CONTENTS
Tires ................................... 6-19
Cast wheels ....................... 6-21
Adjusting the brake lever free
play .................................. 6-21
Adjusting the rear brake lever
free play ........................... 6-21
Battery ................................ 6-22
Replacing the fuse .............. 6-23
Engine oil and oil strainer .... 6-24
Troubleshooting .................. 6-26
Troubleshooting chart ......... 6-27
SCOOTER CARE AND STORAGE ........................................ 7-1
Care...................................... 7-1
Storage ................................. 7-3
SPECIFICATIONS ................. 8-1
CONSUMER INFORMATION 9-1
Identification numbers .......... 9-1
Reporting safety defects ...... 9-3
Motorcycle noise regulation .. 9-4
YAMAHA MOTOR CORPORATION, U.S.A STREET AND
ENDURO MOTORCYCLE
LIMITED WARRANTY ....... 9-5
YAMAHA EXTENDED SERVICE (Y.E.S.) ..................... 9-7
5YR-F8199-11ch0.pmd
6
1
2
3
4
5
6
7
8
9
2004/06/11, 14:11
EAU10220
Q SAFETY INFORMATION
EAU10260
1
2
3
4
5
6
7
8
9
SCOOTERS ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPENDENT UPON
THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERATOR. EVERY OPERATOR SHOULD KNOW THE FOLLOWING REQUIREMENTS BEFORE
RIDING THIS SCOOTER.
HE OR SHE SHOULD:
8 OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT
SOURCE ON ALL ASPECTS OF
SCOOTER OPERATION.
8 OBSERVE THE WARNINGS AND
MAINTENANCE REQUIREMENTS IN THE OWNER’S
MANUAL.
8 OBTAIN QUALIFIED TRAINING IN
SAFE AND PROPER RIDING
TECHNIQUES.
8 OBTAIN PROFESSIONAL TECHNICAL SERVICE AS INDICATED
BY THE OWNER’S MANUAL AND/
OR WHEN MADE NECESSARY
BY MECHANICAL CONDITIONS.
Safe riding
8 Always make pre-operation checks.
Careful checks may help prevent
an accident.
8 This scooter is designed to carry
the operator and passenger.
8 The failure of motorists to detect
and recognize scooters in traffic is
the predominating cause of automobile/scooter accidents. Many
accidents have been caused by an
automobile driver who did not see
the scooter. Making yourself conspicuous appears to be very effective in reducing the chance of this
type of accident.
Therefore:
9 Wear a brightly colored jacket.
9 Use extra caution when
approaching and passing
through intersections, since
intersections are the most
likely places for scooter
accidents to occur.
9 Ride where other motorists can
see you. Avoid riding in another
motorist’s blind spot.
8 Many accidents involve inexperienced operators. In fact, many operators who have been involved in
accidents do not even have a current driver’s license.
9 Make sure that you are qualified and that you only lend your
scooter to other qualified
operators.
9 Know your skills and limits.
Staying within your limits may
help you to avoid an accident.
9 We recommend that you
practice riding your scooter
where there is no traffic until
you have become thoroughly
familiar with the scooter and all
of its controls.
Many accidents have been caused
by error of the scooter operator. A
typical error made by the operator
is veering wide on a turn due to
EXCESSIVE
SPEED
or
undercornering (insufficient lean
angle for the speed).
9 Always obey the speed limit
and never travel faster than
warranted by road and traffic
conditions.
1-1
5YR-F8199-11ch1.pmd
1
2004/06/11, 14:11
Q SAFETY INFORMATION
9 Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
8 The posture of the operator and
passenger is important for proper
control.
9 The operator should keep both
hands on the handlebar and
both feet on the footboard
during operation to maintain
control of the scooter.
9 The passenger should always
hold onto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
feet on the passenger footrests.
9 Never carry a passenger unless
he or she can firmly place both
feet on the passenger footrests.
8 Never ride under the influence of
alcohol or other drugs.
This scooter is designed for on-road
use only. It is not suitable for offroad use.
Protective apparel
The majority of fatalities from scooter
accidents are the result of head injuries.
The use of a safety helmet is the single
most critical factor in the prevention or
reduction of head injuries.
8 Always wear an approved helmet.
8 Wear a face shield or goggles. Wind
in your unprotected eyes could contribute to an impairment of vision
which could delay seeing a hazard.
8 The use of a jacket, substantial
shoes, trousers, gloves, etc., is
effective in preventing or reducing
abrasions or lacerations.
8 Never wear loose-fitting clothes,
otherwise they could catch on the
control levers or wheels and cause
injury or an accident.
8 Never touch the engine or exhaust
system during or after operation.
They become very hot and can
cause burns. Always wear protective clothing that covers your legs,
ankles, and feet.
8 Passengers should also observe
the above precautions.
Modifications
Modifications made to this scooter not
approved by Yamaha, or the removal of
original equipment, may render the
scooter unsafe for use and may cause
severe personal injury. Modifications
may also make your scooter illegal to
use.
Loading and accessories
Adding accessories or cargo to your
scooter can adversely affect stability
and handling if the weight distribution of
the scooter is changed. To avoid the
possibility of an accident, use extreme
caution when adding cargo or accessories to your scooter. Use extra care when
riding a scooter that has added cargo or
accessories. Here are some general
guidelines to follow if loading cargo or
adding accessories to your scooter:
1-2
5YR-F8199-11ch1.pmd
2
2004/06/11, 14:11
1
2
3
4
5
6
7
8
9
Q SAFETY INFORMATION
1
2
3
4
5
6
7
8
9
Loading
The total weight of the operator, passenger, accessories and cargo must not exceed the maximum load limit of 144 kg
(317 lb). When loading within this weight
limit, keep the following in mind:
8 Cargo and accessory weight should
be kept as low and close to the
scooter as possible. Make sure to
distribute the weight as evenly as
possible on both sides of the
scooter to minimize imbalance or
instability.
8 Shifting weights can create a sudden imbalance. Make sure that accessories and cargo are securely
attached to the scooter before riding.
Check accessory mounts and
cargo restraints frequently.
8 Never attach any large or heavy
items to the handlebar, front fork,
or front fender. Such items can create unstable handling or a slow
steering response.
Accessories
Genuine Yamaha accessories have
been specifically designed for use on
this scooter. Since Yamaha cannot test
all other accessories that may be available, you must personally be responsible
for the proper selection, installation and
use of non-Yamaha accessories. Use
extreme caution when selecting and installing any accessories.
Keep the following guidelines in mind,
as well as those provided under “Loading” when mounting accessories.
8 Never install accessories or carry
cargo that would impair the performance of your scooter. Carefully
inspect the accessory before using it to make sure that it does not
in any way reduce ground clearance or cornering clearance, limit
suspension travel, steering travel
or control operation, or obscure
lights or reflectors.
9 Accessories fitted to the
handlebar or the front fork area
can create instability due to
improper weight distribution or
aerodynamic changes. If
accessories are added to the
handlebar or front fork area,
they must be as lightweight as
possible and should be kept to
a minimum.
9 Bulky or large accessories may
seriously affect the stability of
the scooter due to aerodynamic
effects. Wind may attempt to
lift the scooter, or the scooter
may become unstable in cross
winds. These accessories may
also cause instability when
passing or being passed by
large vehicles.
9 Certain accessories can
displace the operator from his
or her normal riding position.
This improper position limits
the freedom of movement of
the operator and may limit
control ability, therefore, such
accessories are not recommended.
8 Use caution when adding electrical
accessories. If electrical accessories exceed the capacity of the
scooter’s electrical system an elec-
1-3
5YR-F8199-11ch1.pmd
3
2004/06/11, 14:11
Q SAFETY INFORMATION
tric failure could result, which could
cause a dangerous loss of lights or
engine power.
Gasoline and exhaust gas
8 GASOLINE IS HIGHLY FLAMMABLE:
9 Always turn the engine off
when refueling.
9 Take care not to spill any
gasoline on the engine or
exhaust system when refueling.
9 Never refuel while smoking or
in the vicinity of an open flame.
8 Never start the engine or let it run
for any length of time in a closed
area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a
short time. Always operate your
scooter in an area that has adequate
ventilation.
8 Always turn the engine off before
leaving the scooter unattended and
remove the key from the main
switch. When parking the scooter,
note the following:
9 The engine and exhaust
system may be hot, therefore,
park the scooter in a place
where pedestrians or children
are not likely to touch these hot
areas.
9 Do not park the scooter on a
slope or soft ground, otherwise
it may fall over.
9 Do not park the scooter near a
flammable source (e.g., a
kerosene heater, or near an
open flame), otherwise it could
catch fire.
8 If you should swallow any gasoline,
inhale a lot of gasoline vapor, or
allow gasoline to get into your eyes,
see your doctor immediately. If any
gasoline spills on your skin or clothing, immediately wash the affected
area with soap and water and
change your clothes.
4
2
3
4
5
6
7
8
9
1-4
5YR-F8199-11ch1.pmd
1
2004/06/11, 14:11
Q SAFETY INFORMATION
EAU10350
Further safe-riding points
1
2
3
4
5
ZAUM00**
Turn left
6
7
8
9
ZAUM00**
Turn right
8 Make sure to signal clearly when
making turns.
8 Braking can be extremely difficult
on a wet road. Avoid hard braking,
because the scooter could slide.
Apply the brakes slowly when stopping on a wet surface.
8 Slow down as you approach a corner or turn. Once you have completed a turn, accelerate slowly.
8 Be careful when passing parked
cars. A driver might not see you and
open a door in your path.
8 Railroad crossings, streetcar rails,
iron plates on road construction
sites, and manhole covers become
extremely slippery when wet. Slow
down and cross them with caution.
Keep the scooter upright, otherwise
it could slide out from under you.
8 The brake lining could get wet when
you wash the scooter. After washing the scooter, check the brakes
before riding.
8 Always wear a helmet, gloves, trousers (tapered around the cuff and
ankle so they do not flap), and a
bright colored jacket.
8 Do not carry too much luggage on
the scooter. An overloaded scooter
is unstable. Use a strong cord to
secure any luggage to the carriers.
A loose load will affect the stability
of the scooter and could divert your
attention from the road. (See page
1-2.)
1-5
5YR-F8199-11ch1.pmd
5
2004/06/11, 14:11
Q SAFETY INFORMATION
EAU10381
Location of important labels
Please read the following important labels carefully before operating this vehicle.
1
2
3
1
2 3
4
6
5
5
6
7
4
8
9
1-6
5YR-F8199-11ch1.pmd
6
2004/06/11, 14:11
Q SAFETY INFORMATION
1
5
1
2
3
2
6
4
5
3
6
7
4
8
9
1-7
5YR-F8199-11ch1.pmd
7
2004/06/11, 14:11
DESCRIPTION
EAU10410
Left view
1
4
2
6
5
7
3
2
3
4
1
5
6
7
8
1. Front wheel (page 6-19)
2. Front turn signal light (page 3-2)
3. Luggage hook (page 3-8)
4. Helmet holder (page 3-6)
5. Storage compartment (page 3-7)
6. Rear turn signal light (page 3-2)
7. Rear wheel (page 6-19)
8. Rear brake lever free play adjusting nut (page 6-21)
9. Kickstarter (page 3-6)
10.Air filter element (page 6-8)
11.Battery (page 6-22)
8
11
10
9
9
2-1
5YR-F8199-11ch2.pmd
1
2004/06/11, 14:12
DESCRIPTION
EAU10420
Right view
1
2
12 13 14
3
16
15
17
4
5
6
7
18
8
9
12.Tail/brake light (page6-11)
13.Carrier (page3-8)
14.Fuel tank cap (page 3-4)
15.Seat (page 3-6)
16.Brake master cylinder (page 6-13)
17.Headlight (page 6-16)
18.Front brake caliper (page 6-12)
19.Spark plug (page 6-7)
20.Centerstand (page 6-15)
21.Muffler (page 3-5)
5YR-F8199-11ch2.pmd
2
21
20
19
2-2
2004/06/11, 14:12
DESCRIPTION
EAU10430
Controls and instruments
1
2
24
25
3
23
22
4
26
5
6
28
29
27
7
8
9
22.Rear brake lever (page 3-4)
23.Left handlebar switches (page 3-2)
24.Speedometer unit (page 3-3)
25.Right handlebar switches (page 3-2)
26.Front brake lever (page 3-3)
27.Throttle grip (page 6-19)
28.Main switch / steering lock (page 3-1)
29.Fuel gauge (page 3-3)
2-3
5YR-F8199-11ch2.pmd
3
2004/06/11, 14:12
INSTRUMENT AND CONTROL FUNCTIONS
EAU10460
EAU10680
LOCK
The steering is locked, and all electrical
systems are off. The key can be removed.
Main switch/steering lock
1
2
1
To lock the steering
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF” position, and then turn it to “LOCK”
while still pushing it.
3. Remove the key.
2
3
ZAUM00**
4
5
6
1. Turn
2. Release
ZAUM00**
The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
positions are described below.
7
1
8
EAU10530
ON
All electrical circuits are supplied with
power, the taillight comes on, and the
engine can be started. The key cannot
be removed.
NOTE:
The headlight and meter lighting come
on automatically when the engine is
started.
9
EAU10660
OFF
All electrical systems are off. The key
can be removed.
ZAUM00**
To unlock the steering
Push the key in, and then turn it to “OFF”
while still pushing it.
EWA10060
w
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving,
otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident. Make
sure that the vehicle is stopped before turning the key to “OFF” or
“LOCK”.
1. Push
3-1
5YR-F8199-11ch3.pmd
1
2004/06/11, 14:12
INSTRUMENT AND CONTROL FUNCTIONS
EAU10980
Indicator lights
EAU12342
Handlebar switches
EAU11020
5”
Turn signal indicator light “5
This indicator light flashes when the turn
signal switch is pushed to the left or right.
1
40
50
30
1
60
80
60
40
20
EAU12400
%/&
&”
Dimmer switch “%
Set this switch to “&” for the high beam
and to “%” for the low beam.
2
EAU12660
#/$
$”
Engine stop switch “#
Set this switch to “#” before starting
the engine. Set this switch to “$” to stop
the engine in case of an emergency, such
as when the motorcycle overturns or
when the throttle cable is stuck.
2
1
100
20
3
0
0
80
4
MPH
3
5
2
ZAUM00**
ZAUM00**
1. Dimmer switch “%/&“
2. Turn signal switch “4/6”
3. Horn switch “*”
1. High beam indicator light ”&”
2. Turn indicator light “5”
EAU12460
&”
High beam indicator light “&
This indicator light comes on when the
high beam of the headlight is switched
on.
4/6
6”
Turn signal switch “4
To signal a right-hand turn, push this
switch to “4”. To signal a left-hand turn,
push this switch to “6”. When released,
the switch returns to the center position.
To cancel the turn signal lights, push the
switch in after it has returned to the center position.
EAU12500
1. Engine stop switch “#/$“
2. Start switch “,”
7
EAU12700
,”
Start switch “,
Push this switch while applying the front
or rear brake to crank the engine with
the starter.
ECA10050
cC
See page 5-1 for starting instructions
prior to starting the engine.
*”
Horn switch “*
Press this switch to sound the horn.
3-2
2
6
ZAUM00**
EAU11080
5YR-F8199-11ch3.pmd
2
70
120
10
1
2004/06/11, 14:12
8
9
INSTRUMENT AND CONTROL FUNCTIONS
EAU11620
Speedometer unit
1
EAU12150
Fuel gauge
1
1
1
40
EAU12900
Front brake lever
50
30
60
80
60
40
20
2
100
20
70
120
10
0
0
80
MPH
3
4
5
6
7
ZAUM00**
ZAUM00**
ZAUM00**
1. Speedometer
1. Fuel gauge
1. Front brake lever
The speedometer unit is equipped with
a speedometer and an odometer. The
speedometer shows riding speed. The
odometer shows the total distance traveled.
The fuel gauge indicates the amount of
fuel in the fuel tank. The needle moves
towards “E” (Empty) as the fuel level
decreases. When the needle reaches the
red line, refuel as soon as possible.
NOTE:
Do not allow the fuel tank to empty itself completely.
The front brake lever is located on the
right handlebar grip. To apply the front
brake, pull this lever toward the handlebar grip.
8
9
3-3
5YR-F8199-11ch3.pmd
3
2004/06/11, 14:12
INSTRUMENT AND CONTROL FUNCTIONS
EAU12950
Rear brake lever
1
ZAUM00**
1. Rear brake lever
The rear brake lever is located on the
left handlebar grip. To apply the rear
brake, pull this lever toward the handlebar grip.
EAU32430
Recommended fuel:
REGULAR UNLEADED GASOLINE ONLY
Fuel tank capacity:
4.5 L (1.18 US gal) (0.98 Imp.gal)
Your Yamaha engine has been designed
to use regular unleaded gasoline with a
pump octane number [(R+M)/2] of 86 or
higher, or a research octane number of
91 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand
or a gasoline or premium unleaded fuel.
Use of unleaded fuel will extend spark
plug life and reduce maintenance cost.
Gasohol
There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if ethanol content does
not exceed 10%. Gasohol containing
methanol is not recommended by
Yamaha because it can cause damage
to the fuel system or vehicle performance problems.
EAU32481
Fuel tank cap
2
1
2
3
ZAUM00**
1. Fuel tank cap cover
2. Match mark
To remove the fuel tank cap
Slide the lock cover open, insert the key
into the lock, and then turn it 1/4 turn
clockwise. The lock will be released and
the fuel tank cap can be removed.
4
4
5
6
7
8
To install the fuel tank cap
1. Insert the fuel tank cap into the tank
opening with the key inserted in the
lock and with the marks on the cap
and tank aligned.
2. Turn the key counterclockwise to
the original position, remove it, and
then close the lock cover.
3-4
5YR-F8199-11ch3.pmd
1
2004/06/11, 14:12
9
INSTRUMENT AND CONTROL FUNCTIONS
1
NOTE:
The fuel tank cap cannot be installed
unless the key is in the lock. In addition, the key cannot be removed if the
cap is not properly installed and locked.
2
EWA10130
EWA10880
w
8 Do not overfill the fuel tank, otherwise it may overflow when the
fuel warms up and expands.
8 Avoid spilling fuel on the hot
engine.
w
3
Make sure that the fuel tank cap is
properly installed before riding.
4
EAU13210
5
Fuel
ECA10070
cC
Immediately wipe off spilled fuel with
a clean, dry, soft cloth, since fuel may
deteriorate painted surfaces or plastic parts.
1
6
7
8
9
EAU13440
Catalytic converter
ZAUM00**
1. Fuel tank filler tube
Make sure that there is sufficient fuel in
the tank. Fill the fuel tank to the bottom
of the filler tube as shown.
This vehicle is equipped with a catalytic
converter in the muffler.
EWA10860
w
The exhaust system is hot after operation. Make sure that the exhaust
system has cooled down before doing any maintenance work.
ECA10700
cC
The following precautions must be
observed to prevent a fire hazard or
other damages.
8 Use only unleaded gasoline. The
use of leaded gasoline will cause
unrepairable damage to the catalytic converter.
8 Never park the vehicle near possible fire hazards such as grass
or other materials that easily
burn.
8 Do not allow the engine to idle
too long.
3-5
5YR-F8199-11ch3.pmd
5
2004/06/11, 14:12
INSTRUMENT AND CONTROL FUNCTIONS
EAU13680
Kickstarter
EAU13931
Seat
NOTE:
Make sure that the seat is properly secured before riding.
1
OPEN
EAU14300
Helmet holder
1
2
3
1
ZAUM00**
4
ZAUM00**
1. Kickstarter
To star t the engine, fold out the
kickstarter lever, move it down lightly
with your foot until the gears engage,
and then push it down smoothly but
forcefully.
To open the seat
1. Place the scooter on the
centerstand.
2. Insert the key into the main switch,
and then turn it counterclockwise.
NOTE:
Do not push inward when turning the key.
3. Fold the seat up.
To close the seat
1. Fold the seat down, and then push
it down to lock it in place.
2. Remove the key from the main
switch if the scooter will be left unattended.
5
ZAUM00**
1. Helmet holder (x2)
The helmet holder is located under the
seat.
To secure a helmet to the helmet
holder
1. Open the seat. (See page 3-6.)
2. Attach the helmet to the helmet
holder, and then securely close the
seat.
3-6
5YR-F8199-11ch3.pmd
6
2004/06/11, 14:12
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
EWA10160
w
1
EAU14510
Storage compartment
Never ride with a helmet attached to
the helmet holder, since the helmet
may hit objects, causing loss of control and possibly an accident.
1
2
3
4
5
To release the helmet from the helmet holder
Open the seat, remove the helmet from
the helmet holder, and then close the
seat.
ZAUM00**
1. Storage compartment
There is a storage compartment under
the seat. (See page 3-6.)
6
EWA10960
w
7
8 Do not exceed the load limit of 5
kg (11 lb) for the storage compartment.
8 Do not exceed the maximum
load of 144 kg (317 lb) for the vehicle.
8
9
ECA10080
cC
Keep the following points in mind
when using the storage compartment.
8 Since the storage compartment
accumulates heat when exposed
to the sun, do not store anything
susceptible to heat inside it.
8 To avoid humidity from spreading through the storage compartment, wrap wet articles in a plastic bag before storing them in the
compartment.
8 Since the storage compartment
may get wet while the scooter is
being washed, wrap any articles
stored in the compartment in a
plastic bag.
8 Do not keep anything valuable or
breakable in the storage compartment.
To store a helmet in the storage compartment, place the helmet upside-down
with the front facing forward.
3-7
5YR-F8199-11ch3.pmd
7
2004/06/11, 14:12
INSTRUMENT AND CONTROL FUNCTIONS
NOTE:
8 Some helmets cannot be stored in
the storage compartment because
of their size or shape.
8 Do not leave your scooter unattended with the seat open.
EAU15110
Carrier
1
The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
motorcycle upright.
NOTE:
The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation of
the ignition circuit cut-off system.)
EAUT1070
ZAUM00**
1. rear carrier
EWA10170
w
1. Luggage hook
EWAT1030
w
8 Do not exceed the load limit of 3
kg (7 lb) for the luggage hook.
8 Do not exceed the maximum
load of 144 kg (317 lb) for the vehicle.
w
The vehicle must not be ridden with
the sidestand down, or if the
sidestand cannot be properly moved
up (or does not stay up), otherwise
the sidestand could contact the
ground and distract the operator, resulting in a possible loss of control.
Yamaha’s ignition circuit cut-off system has been designed to assist the
operator in fulfilling the responsibility of raising the sidestand before
starting off. Therefore, check this sys-
3-8
5YR-F8199-11ch3.pmd
8
3
4
5
EWA10240
8 Do not exceed the load limit of 3
kg (7 lb) for the carrier.
8 Do not exceed the maximum
load of 144 kg (317 lb) for the vehicle.
ZAUM00**
1
2
Luggage hook
1
EAU15300
Sidestand
2004/06/11, 14:12
6
7
8
9
INSTRUMENT AND CONTROL FUNCTIONS
tem regularly as described below and
have a Yamaha dealer repair it if it
does not function properly.
1
2
3
4
5
6
EAU15371
Ignition circuit cut-off system
The ignition circuit cut-off system (comprising the sidestand switch and brake
light switches) has the following functions.
8 It prevents star ting when the
sidestand is up, but neither brake
is applied.
8 It prevents starting when either
brake is applied, but the sidestand
is still down.
8 It cuts the running engine when the
sidestand is moved down.
Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.
EWA10250
7
w
8
If a malfunction is noted, have a
Yamaha dealer check the system before riding.
9
3-9
5YR-F8199-11ch3.pmd
9
2004/06/11, 14:12
INSTRUMENT AND CONTROL FUNCTIONS
NOTE:
This check is most reliable if performed with a warmedup engine.
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Keep the front or rear brake applied.
5. Push the start switch.
Does the engine start?
NO
2
3
The sidestand switch may be defective.
The scooter should not be ridden until checked by a
Yamaha dealer.
YES
With the engine still off:
6. Move the sidestand up.
7. Keep the front or rear brake applied.
8. Push the start switch.
Does the engine start?
YES
6
The brake switch may be defective.
The scooter should not be ridden until checked by a
Yamaha dealer.
NO
9
The sidestand switch may be defective.
The scooter should not be ridden until checked by a
Yamaha dealer.
NO
3-10
10
7
8
The system is OK. The scooter can be ridden.
5YR-F8199-11ch3.pmd
4
5
With the engine still running:
9. Move the sidestand down.
Does the engine stall?
YES
1
2004/06/11, 14:12
PRE-OPERATION CHECKS
EAU15591
1
2
The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,
even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss
of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual inspection, to check the following points before each ride.
NOTE:
Pre-operation checks should be made each time the vehicle is used. Such an inspection can be accomplished in a very short
time; and the added safety it assures is more than worth the time involved.
3
EWA11150
4
w
If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operating
the vehicle.
5
6
7
8
9
4-1
5YR-F8199-11ch4.pmd
1
2004/06/11, 14:12
PRE-OPERATION CHECKS
EAU15602
Pre-operation check list
ITEM
CHECKS
PAGE
1
Fuel
• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.
Engine oil
• Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.
6-24
Final transmission oil
• Check vehicle for oil leakage.
6-17
Front brake
•
•
•
•
•
•
Check operation.
If soft or spongy, have Yamaha dealer bleed hydraulic system.
Check fluid level in reservoir.
If necessary, add recommended brake fluid to specified level.
Check hydraulic system for leakage.
Check the brake pads for wear.
Rear brake
•
•
•
•
Check operation.
Lubricate cable if necessary.
Check lever free play.
Adjust if necessary.
Throttle grip
• Make sure that operation is smooth.
• Check cable free play.
• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and
grip housing.
6-19
Wheels and tires
•
•
•
•
6-19
Brake levers
• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.
6-14
Centerstand, sidestand
• Make sure that operation is smooth.
• Lubricate pivots if necessary.
6-15
3-2, 3-5
2
4-2
5YR-F8199-11ch4.pmd
2
4
6-12~6-13, 6-21
5
6-21
Check for damage.
Check tire condition and tread depth.
Check air pressure.
Correct if necessary.
2004/06/11, 14:12
3
6
7
8
9
PRE-OPERATION CHECKS
ITEM
CHECKS
• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.
Chassis fasteners
1
2
Instruments, lights, signals
and switches
• Check operation.
• Correct if necessary.
Engine stop switch
• Check operation.
Sidestand switch
• Check operation of ignition circuit cut-off system.
• If system is defective, have Yamaha dealer check vehicle.
3-2
3-8~3-10
4
5
6
7
8
9
4-3
3
3-2~3-3
3
5YR-F8199-11ch4.pmd
PAGE
2004/06/11, 14:12
OPERATION AND IMPORTANT RIDING POINTS
EAU15980
EWA10870
w
8 Become thoroughly familiar with
all operating controls and their
functions before riding. Consult
a Yamaha dealer regarding any
control or function that you do
not thoroughly understand.
8 Never start the engine or operate
it in a closed area for any length
of time. Exhaust fumes are poisonous, and inhaling them can
cause loss of consciousness and
death within a short time. Always
make sure that there is adequate
ventilation.
8 For safety, always start the engine
with the centerstand down.
EAU16590
Starting a cold engine
8 Never ride with the sidestand
down.
1. Turn the key to “ON” and make sure
that the engine stop switch is set
to “#”.
2. Close the throttle completely.
3. Start the engine by pushing the
start switch while applying the front
or rear brake.
ECA10250
cC
See page 5-3 for engine break-in instructions prior to operating the vehicle for the first time.
NOTE:
If the engine does not start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to preserve the battery. Do not crank the engine more than 10 seconds on any one
attempt. If the engine does not start, try
with the throttle open 1/8 turn.
EWA10290
w
8 Before starting the engine, check
the function of the ignition circuit cut-off system according to
the procedure described on page
3-8.
ECA11130
cC
For maximum engine life, always
warm the engine up before starting
off. Never accelerate hard when the
engine is cold!
5-1
1
2
3
4
ZAUM00**
In order for the ignition circuit cut-off
system to enable starting, the sidestand
must be up.
5YR-F8199-11ch5.pmd
1
2004/06/11, 14:12
5
6
7
8
9
OPERATION AND IMPORTANT RIDING POINTS
EAU16770
Starting off
EAU16780
Acceleration and deceleration
a 40
1
50
30
60
80
60
40
20
100
b
20
10
2
b
70
120
0
0
80
MPH
1
3
a
ZAUM00**
4
1. Start switch “,”
ZAUM00**
NOTE:
Before starting off, allow the engine to
warm up.
5
6
7
2
8
ZAUM00**
9
ZAUM00**
2. Kickstarter
1. While pulling the rear brake lever
with your left hand and holding the
carrier with your right hand, push
the scooter off the centerstand.
2. Sit astride the seat, and then adjust the rear view mirrors.
3. Switch the turn signal on.
4. Check for oncoming traffic, and
then slowly turn the throttle grip (on
the right) in order to take off.
5. Switch the turn signal off.
The speed can be adjusted by opening
and closing the throttle. To increase the
speed, turn the throttle grip in direction
a. To reduce the speed, turn the throttle
grip in direction b.
5-2
5YR-F8199-11ch5.pmd
2
2004/06/11, 14:12
OPERATION AND IMPORTANT RIDING POINTS
EAU16791
Braking
2
1
when wet. Therefore, slow down
when approaching such areas
and cross them with caution.
8 Keep in mind that braking on a
wet road is much more difficult.
8 Ride slowly down a hill, as braking downhill can be very difficult.
EAU16830
Engine break-in
There is never a more important period
in the life of your engine than the period
between 0 and 1000 km (600 mi). For
this reason, you should read the following material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1000 km (600 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances. During this period, prolonged full-throttle
operation or any condition that might
result in engine overheating must be
avoided.
ZAUM00**
1. Rear
2. Front
1. Close the throttle completely.
2. Apply both front and rear brakes simultaneously while gradually increasing the pressure.
1
2
3
4
5
6
7
EWA10300
w
8
8 Avoid braking hard or suddenly
(especially when leaning over to
one side), otherwise the scooter
may skid or overturn.
8 Railroad crossings, streetcar
rails, iron plates on road construction sites, and manhole covers become extremely slippery
9
5-3
5YR-F8199-11ch5.pmd
3
2004/06/11, 14:13
OPERATION AND IMPORTANT RIDING POINTS
EAU16990
0~500 km (0~300 mi)
Avoid prolonged operation above 1/3
throttle.
EAU17211
8 Since the engine and exhaust
system can become very hot,
park in a place where pedestrians or children are not likely to
touch them.
8 Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn.
1
2
500~1000 km (300~600 mi)
Avoid prolonged operation above 1/2
throttle.
ECA11500
3
4
5
6
7
EWA10310
w
Parking
cC
After 1000 km (600 mi) of operation,
the engine oil must be changed, and
the oil filter element and the oil
strainer cleaned.
ECA10380
cC
Never park in an area where there are
fire hazards such as grass or other
flammable materials.
1000 km (600 mi) and beyond
The vehicle can now be operated normally.
ECA10270
cC
8
9
If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.
When parking, stop the engine, and then
remove the key from the main switch.
5-4
5YR-F8199-11ch5.pmd
4
2004/06/11, 14:13
EAU17222
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU17231
Safety is an obligation of the owner.
Periodic inspection, adjustment and lubrication will keep your vehicle in the
safest and most efficient condition possible. The most important points of motorcycle inspection, adjustment, and lubrication are explained on the following
pages.
Maintenance, replacement, or repair
of the emission control devices and
systems may be performed by any
repair establishment or individual that
is certified (if applicable).
EWA10320
w
SURE CLEANER AIR, BUT ARE ALSO
VITAL TO PROPER ENGINE OPERATION AND MAXIMUM PERFORMANCE. IN THE FOLLOWING PERIODIC MAINTENANCE CHARTS, THE
SERVICES RELATED TO EMISSIONS
CONTROL ARE GROUPED SEPARATELY. THESE SERVICES REQUIRE
SPECIALIZED DATA, KNOWLEDGE,
AND EQUIPMENT.YAMAHA DEALERS
ARE TRAINED AND EQUIPPED TO
PERFORM THESE PARTICULAR SERVICES.
EAU17370
Owner’s tool kit
1
2
3
4
NOTE:
If you do not have the tools or experience required for a particular job, have
a Yamaha dealer perform it for you.
5
6
If you are not familiar with maintenance work, have a Yamaha dealer do
it for you.
EWA10340
w
1
EAU17300
PERIODIC MAINTENANCE
PROPER PERIODIC MAINTENANCE
OF YOUR MOTORCYCLE IS IMPORTANT IN ORDER TO ENJOY LONG,
PLEASURABLE SERVICE. ESPECIALLY IMPORTANT ARE THE MAINTENANCE SERVICES RELATED TO
EMISSIONS CONTROL. THESE CONTROLS NOT ONLY FUNCTION TO EN-
5YR-F8199-11ch6.pmd
The owner’s tool kit is located under the
seat. (See page 3-6.)
The service information included in this
manual and the tools provided in the
owner’s tool kit are intended to assist
you in the performance of preventive
maintenance and minor repairs. However, additional tools such as a torque
wrench may be necessary to perform
certain maintenance work correctly.
1
Modifications not approved by
Yamaha may cause loss of performance, excessive emissions, and render the vehicle unsafe for use. Consult a Yamaha dealer before attempting any changes.
ZAUM00**
1. Owner’s tool kit
6-1
2004/06/11, 14:01
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU17560*
Periodic maintenance chart for the emission control system
ODOMETER READING
600 mi 2,000 mi 4,000 mi 6,000 mi 8,000 mi
(1,000 (4,000 (7,000 (10,000 (13,000
km)
km)
km)
km)
km)
or
or
or
or
or
1
6
12
18
24
month months months months months
1
NO.
ITEM
ROUTINE
2
3
1
*
Fuel line
• Check fuel hoses and vacuum hose for cracks or damage.
—
—
—
—
• Check valve clearance.
• Adjust if necessary.
—
—
—
—
• Check condition.
• Clean and regap.
—
—
—
—
2
*
Valves
3
*
Spark plug
4
8
—
• Clean.
*
Air filter element
5
*
Crankcase breather
system
• Check breather hose for cracks or damage.
• Replace if necessary.
6
*
Carburetor
• Adjust engine idling speed.
4
6
7
—
• Replace.
5
—
• Replace.
—
—
—
—
—
—
—
—
—
—
—
—
—
—
7
*
Exhaust system
• Check for leakage.
• Tighten if necessary.
• Replace gaskets if necessary.
8
*
Evaporative emission
control system
• Checkcontrol system for damage.
• Replace if necessary.
—
9
*
Air induction system
• Check the air cut-off valve, reed valve, and hose for damage.
• Replace any damaged.
—
9
—
—
—
—
—
—
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
NOTE:
From 10000 mi (16000 km) or 30 months, repeat the maintenance intervals starting from 2000 mi (4000 km) or 6 months.
6-2
5YR-F8199-11ch6.pmd
2
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU32121
General maintenance and lubrication chart
ODOMETER READING
NO.
ITEM
1
*
V-belt case air filter
elements
2
*
Front brake
600 mi 2,000 mi 4,000 mi 6,000 mi 8,000 mi
(1,000 (4,000 (7,000 (10,000 (13,000
km)
km)
km)
km)
km)
or
or
or
or
or
1
6
12
18
24
month months months months months
ROUTINE
—
• Clean.
• Check operation, fluid level and vehicle for fluid leakage.
(See NOTE on page 6-5.)
—
• Replace brake pads.
—
—
• Check operation and adjust brake lever free play.
—
*
Rear brake
4
*
Brake hose
5
*
Wheels
• Check runout and for damage.
—
*
Tires
• Check tread depth and for damage.
• Replace if necessary.
• Check air pressure.
• Correct if necessary.
—
*
Wheel bearings
7
—
3
—
—
—
4
• Replace brake shoes.
—
—
—
5
Whenever worn to the limit
—
• Check for cracks or damage.
• Replace. (See NOTE on page 6-5.)
—
—
—
—
—
—
—
—
—
Every 4 years
• Check bearing for looseness or damage.
—
• Check bearing play and steering for roughness.
—
—
—
—
—
—
—
—
*
Steering bearings
9
*
Chassis fasteners
• Make sure that all nuts, bolts and screws are properly tightened.
—
—
—
—
Sidestand, centerstand
• Check operation.
• Lubricate.
—
—
—
—
• Lubricate with lithium-soap-based grease.
Every 16,000 mi (24,000 km)
6-3
5YR-F8199-11ch6.pmd
3
6
7
8
8
10
2
Whenever worn to the limit
3
6
—
—
• Replace.
1
2004/06/11, 14:01
9
PERIODIC MAINTENANCE AND MINOR REPAIR
ODOMETER READING
NO.
ITEM
600 mi 2,000 mi 4,000 mi 6,000 mi 8,000 mi
(1,000 (4,000 (7,000 (10,000 (13,000
km)
km)
km)
km)
km)
or
or
or
or
or
1
6
12
18
24
month months months months months
ROUTINE
1
2
11
12
3
4
13
14
15
5
*
*
*
16
*
*
—
Sidestand switch
• Check operation.
Front fork
• Check operation and for oil leakage.
Shock absorber assembly • Check operation and shock absorber for oil leakage.
—
—
—
—
—
—
—
—
—
—
• Change.
• Check oil level and vehicle for leakage.
—
Engine oil filter element
• Clean.
—
—
—
Engine oil strainer
• Clean.
—
—
—
—
—
—
Final transmission oil
• Change.
18
*
V-belt
• Replace.
19
*
Front and rear brake
switches
• Check operation.
20
Moving parts and cables
• Lubricate.
8
21
*
• Check operation and free play.
Throttle grip housing and
• Adjust the throttle cable free play if necessary.
cable
• Lubricate the throttle grip housing and cable.
9
22
*
Lights, signals and
switches
7
—
Engine oil
17
6
—
Every 1,900 mi (3,000 km)
Every 12,000 mi (18,000 km)
—
• Check operation.
• Adjust headlight beam.
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
NOTE:
From 12000 mi (18000 km) or 36 months, repeat the maintenance intervals starting from 4000 mi (7000 km) or 12 months.
6-4
5YR-F8199-11ch6.pmd
4
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU17620
NOTE:
8 The air filter needs more frequent service if you are riding in unusually wet or dusty areas.
8 Hydraulic brake system
9 When disassembling the master cylinder or caliper cylinder, always replace the brake fluid. Check the brake fluid
level regularly and fill as required.
9 Replace the oil seals on the inner parts of the master cylinder and caliper cylinder every two years.
9 Replace the brake hoses every four years or if cracked or damaged.
1
2
3
4
5
6
7
8
9
6-5
5YR-F8199-11ch6.pmd
5
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU18771
Removing and installing panels
EAU19210
Panel A
EAU19210
Panel B
2
1
2
1
2
3
1
4
1
ZAUM00**
2
ZAUM00**
5
1. Panel A
2. Panel B
6
7
8
The panels shown above need to be removed to perform some of the maintenance jobs described in this chapter.
Refer to this section each time a panel
needs to be removed and installed.
ZAUM00**
1. Panel A
2. Screw (x2)
1. Panel B
2. Screw (x2)
To remove the panel
Remove the screws, and then take the
panel off.
To remove the panel
Remove the screws, and then take the
panel off.
To install the panel
Place the panel in the original position,
and then install the screws.
To install the panel
Place the panel in the original position,
and then install the screws.
9
6-6
5YR-F8199-11ch6.pmd
6
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAUT1170
Checking the spark plug
1
NOTE:
If the spark plug shows a distinctly different color, the engine could be defective. Do not attempt to diagnose such
problems yourself. Instead, have a
Yamaha dealer check the vehicle.
ZAUM00**
1. Spark plug cap
The spark plug is an important engine
component, which is easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plug should be removed and checked in
accordance with the periodic maintenance and lubrication chart. In addition,
the condition of the spark plug can reveal the condition of the engine.
To remove the spark plug
1. Remove panel A. (See page 6-6.)
2. Remove the spark plug cap.
3. Remove the spark plug as shown,
with the spark plug wrench included
in the owner’s tool kit.
5YR-F8199-11ch6.pmd
To check the spark plug
1. Check that the porcelain insulator
around the center electrode of the
spark plug is a medium-to-light tan
(the ideal color when the vehicle is
ridden normally).
7
2. Check the spark plug for electrode
erosion and excessive carbon or
other deposits, and replace it if necessary.
Specified spark plug:
CR7E (NGK)
To install the spark plug
1. Measure the spark plug gap with a
wire thickness gauge and, if necessary, adjust the gap to specification.
1
2
1
3
ZAUM0037
1. Spark plug gap
Spark plug gap:
0.7~0.8 mm (0.028~0.032 in)
2. Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads.
3. Install the spark plug with the spark
plug wrench, and then tighten it to
the specified torque.
4
5
6
7
8
9
Tightening torque:
Spark plug:
13 Nm (1.3m • kgf, 9.4ft • lbf)
6-7
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
NOTE:
If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4~1/2 turn past
finger tight. However, the spark plug
should be tightened to the specified
torque as soon as possible.
4. Install the spark plug cap.
5. Install the panel.
EAUT1301
Air filter and V-belt case air filter elements
Air filter and V-belt case air filter
The air filter and V-belt case air filter elements should be cleaned at the intervals specified in the periodic maintenance and lubrication chart. Clean both
filter elements more frequently if you are
riding in unusually wet or dusty areas.
4
Cleaning the air filter element
1. Place the scooter on
centerstand.
5
1. Air filter element
the
6
7
8
1
ZAUM00**
3. Pull the air filter element out, and
then blow the dirt out with compressed air as shown.
4. Check the air filter element for damage and replace it if necessary.
5. Insert the air filter element into the
air filter case.
1
9
ZAUM00**
1. Air filter case cover
2. Remove the air filter case cover by
removing the screw.
6-8
5YR-F8199-11ch6.pmd
8
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
Cleaning the V-belt case air filter element
1. Remove the kickstarter lever by removing the bolt.
2. Remove the crankcase cover by removing the screws.
1
1
2
2
1
3
ZAUM00**
ZAUM00**
1. Compressed air
1
cC
8 Make sure that the air filter element is properly seated in the air
filter case.
8 The engine should never be operated without the air filter element installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.
6.Install the air filter case cover by installing the screw.
EWA10430
9
5
w
3
Use only a dedicated parts cleaning
solvent. To avoid the risk of fire or
explosion, do not use gasoline or
solvents with a low flash point.
2
ZAUM00**
1. Kickstarter
2. Bolt
3. Crankcase cover
ECA10520
3. Remove the filter element holder by
removing the screw.
4. Pull the air filter element out, and
then clean it with solvent. After
cleaning, remove the remaining
solvent by squeezing the element.
6
7
cC
8
To avoid damaging the air filter element, handle it gently and carefully,
and do not twist it.
9
5. Apply oil of the recommended type
to the entire surface of the sponge
material, and then squeeze the excess oil out.
6-9
5YR-F8199-11ch6.pmd
4
1. Filter element holder
2. Filter element
ECA10480
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
NOTE:
The air filter element should be wet but
not dripping.
1
2
3
4
5
6
Recommended oil:
Engine oil
6. Insert the element into the air filter
case.
7. Install the filter element holder by
installing the screw.
8. Install the crankcase cover by installing the screws.
9. Install the kickstarter lever by installing the bolt, then tightening the
bolt to the specified torque.
7
8
Tightening torque:
Kickstarter bolt:
23 Nm (2.3m • kgf, 16.6ft • lbf)
9
6-10
5YR-F8199-11ch6.pmd
10
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU24131
EAU24201
Replacing the tail/brake light
bulb
Replacing a turn signal light
bulb
1
2
2
1
1. Remove the turn signal light lens
by removing the screw.
2. Remove the defective bulb by pushing it in and turning it counterclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clockwise until it stops.
4. Install the lens by installing the
screw.
1
2
3
ECA11190
ZAUM00**
ZAUM00**
1. Light lens
2. Bulb
1. Front light lens
2. Bulb
1. Remove the tail/brake light lens by
removing the screws.
2. Remove the defective bulb by pushing it in and turning it counterclockwise.
3. Insert a new bulb into the socket,
push it in, and then turn it clockwise until it stops.
4. Install the lens by installing the
screws.
ECA10680
cC
cC
4
Do not overtighten the screw, otherwise the lens may break.
5
6
2
7
8
1
9
ZAUM00**
1. Rear light lens
2. Bulb
Do not overtighten the screws, otherwise the lens may break.
6-11
5YR-F8199-11ch6.pmd
11
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU22380
Checking the front brake pads
and rear brake shoes
1
2
EAU22410
Front brake pads
The front brake pads and the rear brake
shoes must be checked for wear at the
intervals specified in the periodic maintenance and lubrication chart.
EAU22540
Rear brake shoes
1
3
2
1
3
4
ZAUM00**
ZAUM00**
1. Wear indicator
2. Brake disk
3. Brake pads
5
6
1. Wear indicator
2. Wear limit line
Each front brake pad is provided with a
wear indicator, which allows you to
check the brake pad wear without having to disassemble the brake. To check
the brake pad wear, check the position
of the wear indicator while applying the
brake. If a brake pad has worn to the
point that the wear indicator almost
touches the brake disc, have a Yamaha
dealer replace the brake pads as a set.
7
8
9
The rear brake is provided with a wear
indicator, which allows you to check the
brake shoe wear without having to disassemble the brake. To check the brake
shoe wear, check the position of the
wear indicator while applying the brake.
If a brake shoe has worn to the point
that the wear indicator reaches the wear
limit line, have a Yamaha dealer replace
the brake shoes as a set.
6-12
5YR-F8199-11ch6.pmd
12
2
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU32341
Checking the brake fluid level
1
LOWER
MIN
ZAUM00**
Observe these precautions:
8 When checking the fluid level,
make sure that the top of the master cylinder is level by turning the
handlebars.
Use only the recommended quality brake fluid, otherwise the rubber seals may deteriorate, causing
leakage and poor braking performance.
Recommended brake fluid:
DOT 4
1. Minimum level mark
Insufficient brake fluid may allow air to
enter the brake system, possibly causing it to become ineffective.
Before riding, check that the brake fluid
is above the minimum level mark and
replenish if necessary. A low brake fluid
level may indicate worn brake pads and/
or brake system leakage. If the brake
fluid level is low, be sure to check the
brake pads for wear and the brake system for leakage.
8 Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and lead
to poor braking performance.
8 Be careful that water does not enter the master cylinder when refilling. Water will significantly lower the
boiling point of the fluid and may
result in vapor lock.
8 Brake fluid may deteriorate painted
surfaces or plastic parts. Always
clean up spilled fluid immediately.
8 As the brake pads wear, it is normal for the brake fluid level to
gradually go down. However, if the
brake fluid level goes down suddenly, have a Yamaha dealer check
the cause.
EAU22720
Changing the brake fluid
Have a Yamaha dealer change the brake
fluid at the intervals specified in the
NOTE after the periodic maintenance
and lubrication chart. In addition, have
the oil seals of the brake master cylinder and caliper as well as the brake hose
replaced at the intervals listed below or
whenever they are damaged or leaking.
8 Oil seals: Replace every two years.
8 Brake hose: Replace every four
years.
6-13
5YR-F8199-11ch6.pmd
13
2004/06/11, 14:01
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
6
7
8
9
EAU23090
EAU23110
EAU23170
Checking and lubricating the
cables
Checking and lubricating the
throttle grip and cable
Lubricating the front and rear
brake levers
The operation of all control cables and
the condition of the cables should be
checked before each ride, and the
cables and cable ends should be lubricated if necessary. If a cable is damaged or does not move smoothly, have
a Yamaha dealer check or replace it.
The operation of the throttle grip should
be checked before each ride. In addition, the cable should be lubricated or
replaced at the intervals specified in the
periodic maintenance chart.
Recommended lubricant:
Yamaha Chain and Cable Lube or
engine oil SAE 10W-30 (API SE)
ZAUM00**
The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic maintenance and lubrication chart.
EWA10710
w
Damage to the outer housing of
cables may result in internal rusting
and cause interference with cable
movement. Replace damaged cables
as soon as possible to prevent unsafe conditions.
Recommended lubricant:
Lithium-soap-based grease (all-purpose grease)
6-14
5YR-F8199-11ch6.pmd
14
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23210
Checking and lubricating the
centerstand and sidestand
EAU23271
Checking the front fork
To check the operation
1. Place the motorcycle on a level surface and hold it in an upright position.
2. While applying the front brake, push
down hard on the handlebars several times to check if the front fork
compresses and rebounds
smoothly.
1
2
3
ECA10590
ZAUM00**
ZAUM00**
The operation of the centerstand and
sidestand should be checked before
each ride, and the pivots and metal-tometal contact surfaces should be lubricated if necessary.
EWA10740
The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic maintenance and lubrication chart.
cC
4
If any damage is found or the front
fork does not operate smoothly, have
a Yamaha dealer check or repair it.
5
6
7
To check the condition
EWA10750
w
w
If the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or repair
it.
8
Securely support the motorcycle so
that there is no danger of it falling
over.
9
Check the inner tubes for scratches,
damage and excessive oil leakage.
Recommended lubricant:
Lithium-soap-based grease (all-purpose grease)
5YR-F8199-11ch6.pmd
15
6-15
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23280
Checking the steering
1
2. Hold the lower ends of the front fork
legs and try to move them forward
and backward. If any free play can
be felt, have a Yamaha dealer check
or repair the steering.
EAU23780
Replacing the headlight bulb
1
2
3
4
5
6
7
8
ZAUM00**
ZAUM00**
1. Headlight unit
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as follows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Place a stand under the engine to
raise the front wheel off the ground.
This model is equipped with a quartz
bulb headlight. If the headlight bulb burns
out, replace it as follows.
1. Remove the headlight unit by removing the screws.
EWA10750
w
9
Securely support the motorcycle so
that there is no danger of it falling
over.
6-16
5YR-F8199-11ch6.pmd
16
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EWA10790
1
2
Final transmission oil
Headlight bulbs get very hot. Therefore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.
The final transmission case must be
checked for oil leakage before each ride.
If any leakage is found, have a Yamaha
dealer check and repair the scooter. In
addition, the final transmission oil must
be changed as follows at the intervals
specified in the periodic maintenance
and lubrication chart.
1. Start the engine, warm it up by
riding the scooter for several minutes, and then stop the engine.
2. Place the scooter on the
centerstand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
4. Place a new headlight bulb into position, and then secure it with the
bulb holder.
ZAUM00**
1. Headlight coupler
2. Bulb cover
ECA10660
cC
2. Disconnect the headlight coupler,
and then remove the bulb cover.
1
EAU20060
w
Do not touch the glass part of the
headlight bulb to keep it free from oil,
otherwise the transparency of the
glass, the luminosity of the bulb, and
the bulb life will be adversely affected.
Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol
or thinner.
1
1
2
3
4
5
6
7
8
9
ZAUM00**
1. Bulb holder
3. Remove the headlight bulb holder
by turning it counterclockwise, and
then remove the defective bulb.
5YR-F8199-11ch6.pmd
17
5. Install the headlight bulb cover, and
then connect the coupler.
6. Install the headlight unit by installing the screws.
7. Have a Yamaha dealer adjust the
headlight beam if necessary.
ZAUM00**
1. Final transmission oil filler cap
6-17
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.13 L (0.14 US qt) (0.1 Imp.qt)
1
1
2
EWA11310
w
3
ZAUM00**
4
5
6
7
8
1. Final transmission gear oil drain bolt
4. Remove the oil filler cap and drain
bolt to drain the oil from the final
transmission case.
5. Install the final transmission oil
drain bolt, and then tighten it to the
specified torque.
8 Make sure that no foreign material enters the final transmission
case.
8 Make sure that no oil gets on the
tire or wheel.
7. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
Tightening torque:
Final transmission oil drain bolt:
23 Nm (2.3m • kgf, 16.6ft • lbf)
9
6. Add the specified amount of the
recommended final transmission
oil, and then install and tighten the
oil filler cap.
6-18
5YR-F8199-11ch6.pmd
18
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU21250
Adjusting the carburetor
EAU21860
Tires
The carburetor is an important part of
the engine and its emission control system, which requires very sophisticated
adjustment. Therefore, carburetor adjustments should be left to Yamaha dealer,
who has the necessary professional
knowledge and experience.
1
2
of the tires equals the ambient
temperature).
8 The tire air pressure must be
adjusted in accordance with the
riding speed and with the total
weight of rider, passenger, cargo,
and accessories approved for this
model.
Adjusting the throttle cable
free play
1. Tread depth
2. Side wall
a
To maximize the performance, durability, and safe operation of your scooter,
note the following points regarding the
specified tires.
Tire air pressure
The tire air pressure should be checked
and, if necessary, adjusted before each
ride.
ZAUM00**
a. 1.5 ~ 3.5mm
EWA10500
The throttle cable free play should measure 1.5~3.5 mm (0.06~0.14 in) at the
throttle grip. Periodically check the
throttle cable free play and, if necessary,
have a Yamaha dealer adjust it.
Front
Rear
4
Up to 90 kg (198 lb)
150 kPa
1.50 kgf/cm2
22 psi
200 kPa
2.0 kgf/cm2
29 psi
5
90 kg (198 lb)–
maximum
150 kPa
1.50kgf/cm2
22psi
225 kPa
2.25 kgf/cm2
32 psi
6
Load*
ZAUM0054
w
8 The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
Maximum load*
19
144 kg (317 lb)
7
* Total weight of rider, passenger, cargo and
accessories
8
EWA10510
w
Proper loading of your vehicle is important for several characteristics of
your vehicle, such as handling, braking, performance and safety. Do not
carry loosely packed items that can
shift. Securely pack your heaviest
6-19
5YR-F8199-11ch6.pmd
2
3
Tire air pressure
(measured on cold tires)
EAU21380
1
2004/06/11, 14:01
9
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
4
5
items close to the center of the motorcycle, and distribute the weight
evenly from side to side. Properly
adjust the suspension for your load,
and check the condition and pressure
of your tires. NEVER OVERLOAD
YOUR VEHICLE. Make sure that the
total weight of the cargo, rider, passenger, and accessories (cowling,
saddlebags, etc. if approved for this
model) does not exceed the maximum load of the vehicle. Operation
of an overloaded motorcycle could
cause tire damage, an accident, or
even injury.
6
7
8
9
Tire inspection
The tires must be checked before each
ride. If a tire tread shows crosswise lines
(minimum tread depth), if the tire has a
nail or glass fragments in it, or if the
sidewall is cracked, have a Yamaha
dealer replace the tire immediately.
Minimum tire tread depth (front and
rear):
0.8 mm (0.03 in)
NOTE:
The tire tread depth limits may differ from
country to country. Always comply with
the local regulations.
Tire information
This scooter is equipped with cast
wheels and tubeless tires with valves.
EWA10590
w
Operating the scooter with excessively worn tires decrease riding stability and can lead to loss of control.
Have excessively worn tires replaced
by a Yamaha dealer immediately.
Brakes, tires, and related wheel parts
replacement should be left to a
Yamaha Service Technician.
EWA10580
w
8 It is dangerous to ride with a
worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace the
tire immediately.
8 The replacement of all wheeland brake-related parts, including the tires, should be left to a
Yamaha dealer, who has the necessary professional knowledge
and experience.
FRONT
Manufacturer
Cheng shin
Size
Model
3.50-10
51J
Size
Model
3.50-10
51J
REAR
Manufacturer
Cheng shin
6-20
5YR-F8199-11ch6.pmd
20
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU21960
Cast wheels
To maximize the performance, durability, and safe operation of your motorcycle, note the following points regarding the specified wheels.
8 The wheel rims should be checked
for cracks, bends or warpage before each ride. If any damage is
found, have a Yamaha dealer replace the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked wheel
must be replaced.
8 The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in poor
performance, adverse handling
characteristics, and a shortened
tire life.
8 Ride at moderate speeds after
changing a tire since the tire surface must first be “broken in” for it
to develop its optimal characteristics.
EAU22100
EAU22170
Adjusting the brake lever free
play
Adjusting the rear brake lever
free play
1
1
3
4
ZAUM0107
ZAUM0108
1. Free play
5
The brake lever free play should measure 2~5 mm (0.08~0.2 in) as shown.
Periodically check the brake lever free
play and, if necessary, have a Yamaha
dealer adjust it.
1. Free play
6
7
EWA10640
w
1
An incorrect brake lever free play indicates a hazardous condition in the
brake system. Do not operate the
motorcycle until the brake system has
been checked or repaired by a
Yamaha dealer.
b
ZAUM00**
21
a
1. Adjusting nut
6-21
5YR-F8199-11ch6.pmd
2
1
2004/06/11, 14:01
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
1
2
3
The brake lever free play should measure 10~20 mm (0.4~0.8 in) as shown.
Periodically check the brake lever free
play and, if necessary, adjust it as follows.
To increase the brake lever free play,
turn the adjusting nut at the brake shoe
plate in direction (a). To decrease the
brake lever free play, turn the adjusting
nut in direction (b).
EAUT1230
1
EWA10650
4
w
5
If proper adjustment cannot be obtained as described, have a Yamaha
dealer make this adjustment.
ZAUM00**
1. Battery
7
This model is equipped with a sealedtype (MF) battery, which does not require any maintenance. There is no need
to check the electrolyte or to add distilled water.
8
cC
6
ECA10620
Never attempt to remove the battery
cell seals, as this would permanently
damage the battery.
9
EWA10760
w
Battery
8 Electrolyte is poisonous and dangerous since it contains sulfuric
acid, which causes severe burns.
Avoid any contact with skin, eyes
or clothing and always shield
your eyes when working near
batteries. In case of contact, administer the following FIRST AID.
9 EXTERNAL: Flush with
plenty of water.
9 INTERNAL: Drink large
quantities of water or milk
and immediately call a
physician.
9 EYES: Flush with water for
15 minutes and seek prompt
medical attention.
8 Batteries produce explosive hydrogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and provide sufficient ventilation when
charging it in an enclosed space.
8 KEEP THIS AND ALL BATTERIES
OUT OF THE REACH OF CHILDREN.
6-22
5YR-F8199-11ch6.pmd
22
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
The battery is located under the
footboard. Remove panel B to access
the battery. (See page 6-6.)
To charge the battery
Have a Yamaha dealer charge the battery as soon as possible if it seems to
have discharged. Keep in mind that the
battery tends to discharge more quickly
if the vehicle is equipped with optional
electrical accessories.
To store the battery
1. If the vehicle will not be used for
more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.
2. If the battery will be stored for more
than two months, check it at least
once a month and fully charge it if
necessary.
3. Fully charge the battery before installation.
4. After installation, make sure that
the battery leads are properly connected to the battery terminals.
ECA10630
EAUT1240
Replacing the fuse
cC
8 Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.
8 To charge a sealed-type (MF) battery, a special (constant-voltage)
battery charger is required. Using a conventional battery
charger will damage the battery.
If you do not have access to a
sealed-type (MF) battery charger,
have a Yamaha dealer charge
your battery.
1
1
3
ZAUM00**
1. Fuse
The fuse holder is located beside the
battery. Remove panel B to access the
fuse. (See page 6-6.)
If the fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
all electrical circuits.
2. Remove the blown fuse, and then
install a new fuse of the specified
amperage.
Specified fuse:
10 A
6-23
5YR-F8199-11ch6.pmd
23
2
2004/06/11, 14:01
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
ECA10640
1
2
3
4
5
EAUT1180
Engine oil and oil strainer
cC
Do not use a fuse of a higher amperage rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.
3. Turn the key to “ON” and turn on
the electrical circuits to check if the
devices operate.
4. If the fuse immediately blows again,
have a Yamaha dealer check the
electrical system.
6
2
3
2. Start the engine, warm it up for several minutes, and then turn it off.
3. Wait a few minutes until the oil
settles, and then check the oil level
through the check window located
at the bottom-left side of the crankcase.
1
ZAUM00**
1. Level check window
2. Maximum level
3. Minimum level
The engine oil level should be checked
before each ride. In addition, the oil must
be changed and the oil strainer cleaned
at the intervals specified in the periodic
maintenance and lubrication chart.
7
8
To check the engine oil level
1. Place the vehicle on
centerstand.
9
NOTE:
Make sure that the vehicle is positioned
straight up when checking the oil level.
A slight tilt to the side can result in a
false reading.
the
NOTE:
The engine oil should be between the
minimum and maximum level marks.
4. If the engine oil is below the minimum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
6-24
5YR-F8199-11ch6.pmd
24
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
To change the engine oil and clean
the oil strainer
4
1
3 2
1
1
2
1
1
3
ZAUM00**
ZAUM00**
1. Drain bolt A
ZAUM00**
ECA10410
cC
1. Oil filler cap
1. Start the engine, warm it up for several minutes, and then turn it off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove panel A. (See page 6-6.)
4. Remove the engine oil filler cap and
drain bolts to drain the oil from the
crankcase.
When removing the engine oil drain
bolt, the O-ring, spring, and oil
strainer will fall out. Take care not to
lose these parts.
5. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
1.
2.
3.
4.
Drain bolt B
O-ring
Spring
Strainer
6.Check the O-ring for damage and replace it if necessary.
7. Install the oil strainer, spring, O-ring
and engine oil drain bolts, and then
tighten the drain bolts to the specified torque.
Tightening torque:
Engine oil drain bolt A:
23 Nm (2.3m • kgf, 16.6ft • lbf)
Engine oil drain bolt B:
32 Nm (3.2m • kgf, 23.1ft • lbf)
6-25
5YR-F8199-11ch6.pmd
25
2004/06/11, 14:01
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
NOTE:
Make sure that the O-ring is properly
seated.
1
2
3
4
5
8. Add the specified amount of the
recommended engine oil, and then
install and tighten the engine oil filler
cap.
9. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off and
check for the cause.
10. Turn the engine off, and then check
the oil level and correct it if necessary.
11. Install the panel.
Recommended engine oil:
See page 8-1.
Oil change quantity:
1.0 L (1.09 US qt) (0.92 Imp.qt)
ECA11670
6
7
8
9
cC
8 Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
8 Be sure no foreign material enters the crankcase.
EAU25860
Troubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur during operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting chart represents a quick and easy procedure for
checking these vital systems yourself.
However, should your scooter require any
repair, take it to a Yamaha dealer, whose
skilled technicians have the necessary
tools, experience, and know-how to service the scooter properly.
Use only genuine Yamaha replacement
parts. Imitation parts may look like
Yamaha parts, but they are often inferior, have a shorter service life and can
lead to expensive repair bills.
6-26
5YR-F8199-11ch6.pmd
26
2004/06/11, 14:01
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU25901
Troubleshooting chart
EWA10840
w
Keep away open flames and do not smoke while checking or working on the fuel system.
1
2
1. Fuel
There is enough fuel.
Check the compression.
There is no fuel.
Supply fuel.
Check the fuel level in
the fuel tank.
3
The engine does not start.
Check the compression.
4
2. Compression
There is compression.
Check the ignition.
There is no compression.
Have a Yamaha dealer
check the vehicle.
5
Operate the electric starter.
3. Ignition
6
Wet
Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.
Open the throttle halfway and operate
the electric starter.
Dry
Have a Yamaha dealer check the vehicle.
The engine does not start.
Check the battery.
Remove the spark plug
and check the electrodes.
8
9
4. Battery
The engine turns over
quickly.
The battery is good.
The engine turns over
slowly.
Check the battery lead connections,
and charge the battery if necessary.
Operate the electric starter.
6-27
5YR-F8199-11ch6.pmd
7
27
2004/06/11, 14:01
The engine does not start.
Have a Yamaha dealer
check the vehicle.
SCOOTER CARE AND STORAGE
EAU26090
Care
1
2
3
4
5
6
7
8
9
ECA10780
While the open design of a scooter reveals the attractiveness of the technology, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. A
rusty exhaust pipe may go unnoticed on
a car, however, it detracts from the overall appearance of a scooter. Frequent and
proper care does not only comply with
the terms of the warranty, but it will also
keep your scooter looking good, extend
its life and optimize its performance.
Before cleaning
1. Cover the muffler outlet with a plastic bag after the engine has cooled
down.
2. Make sure that all caps and covers as well as all electrical couplers
and connectors, including the spark
plug cap, are tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such products onto seals, gaskets and wheel
axles. Always rinse the dirt and
degreaser off with water.
5YR-F8199-11ch7.pmd
Cleaning
1
cC
8 Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are used
on hard-to-remove dirt, do not
leave the cleaner on the affected
area any longer than instructed.
Also, thoroughly rinse the area
off with water, immediately dry
it, and then apply a corrosion
protection spray.
8 Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use only
a soft, clean cloth or sponge with
mild detergent and water to clean
plastic.
8 Do not use any harsh chemical
products on plastic parts. Be sure
to avoid using cloths or sponges
which have been in contact with
strong or abrasive cleaning products, solvent or thinner, fuel
(gasoline), rust removers or inhibitors, brake fluid, antifreeze or
electrolyte.
8 Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following areas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instruments, switches and lights),
breather hoses and vents.
8 For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as they
will cause dulling or scratching.
Some cleaning compounds for
plastic may leave scratches on
the windshield. Test the product
on a small hidden part of the
windshield to make sure that it
does not leave any marks. If the
windshield is scratched, use a
quality plastic polishing compound after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge, and
7-1
2004/06/11, 14:13
SCOOTER CARE AND STORAGE
then rinse thoroughly with clean water.
Use a toothbrush or bottlebrush for hardto-reach areas. Stubborn dirt and insects
will come off more easily if the area is
covered with a wet cloth for a few minutes before cleaning.
After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely corrosive in combination with water, carry out
the following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.
NOTE:
Salt sprayed on roads in the winter may
remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the engine has cooled down.
ECA10790
cC
Do not use warm water since it increases the corrosive action of the
salt.
2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainlesssteel parts, including the exhaust
system. (Even the thermally induced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
3. To prevent corrosion, it is recommended to apply a corrosion protection spray on all metal, including chrome- and nickel-plated, surfaces.
4. Use spray oil as a universal cleaner
to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely before storing or covering it.
EWA10940
w
8 Make sure that there is no oil or
wax on the brakes or tires. If necessary, clean the brake discs and
brake linings with a regular brake
disc cleaner or acetone, and
wash the tires with warm water
and a mild detergent.
8 Before operating the scooter test
its braking performance and cornering behavior.
2
2
3
4
5
ECA10800
cC
8 Apply spray oil and wax sparingly and make sure to wipe off
any excess.
8 Never apply oil or wax to any rubber and plastic parts, but treat
them with a suitable care product.
8 Avoid using abrasive polishing
compounds as they will wear
away the paint.
7-2
5YR-F8199-11ch7.pmd
1
2004/06/11, 14:13
6
7
8
9
SCOOTER CARE AND STORAGE
NOTE:
Consult a Yamaha dealer for advice on
what products to use.
1
EAU26300
Storage
Short-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover.
ECA10820
2
cC
8 Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
8 To prevent corrosion, avoid
damp cellars, stables (because of
the presence of ammonia) and
areas where strong chemicals are
stored.
3
4
5
6
7
8
Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Drain the carburetor float chamber
by loosening the drain bolt; this will
prevent fuel deposits from building
9
up. Pour the drained fuel into the
fuel tank.
3. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent the
fuel tank from rusting and the fuel
from deteriorating.
4. Perform the following steps to protect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and
spark plug.
b. Pour a teaspoonful of engine oil
into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit sparking during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from
the spark plug, and then install
the spark plug and the spark plug
cap.
7-3
5YR-F8199-11ch7.pmd
3
2004/06/11, 14:13
SCOOTER CARE AND STORAGE
EWA10950
w
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.
°F) or more than 30 °C (90 °F)]. For
more information on storing the
battery, see page 6-23.
NOTE:
Make any necessary repairs before storing the scooter.
5. Lubricate all control cables and the
pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
6. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alternatively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
7. Cover the muffler outlet with a plastic bag to prevent moisture from entering it.
8. Remove the battery and fully charge
it. Store it in a cool, dry place and
charge it once a month. Do not store
the battery in an excessively cold
or warm place [less than 0 °C (30
4
2
3
4
5
6
7
8
9
7-4
5YR-F8199-11ch7.pmd
1
2004/06/11, 14:13
SPECIFICATIONS
Dimensions:
1
2
3
4
5
6
7
8
9
Oil type or grade
Engine oil
Overall length:
1,755 mm (69.1 in)
Overall width:
699 mm (27.5 in)
Overall height:
1,063 mm (41.8 in)
Seat height:
759 mm (29.8 in)
Wheel base:
1,230 mm (48.4 in)
Ground clearance:
95 mm (3.8 in)
Minimum turning radius:
1,800 mm (72 in)
Fuel
Type
-20˚ -10˚
0˚
10˚
20˚ 30˚
40˚ 50˚
Type
Regular unleaded gasoline(91 or higher)
Fuel tank capacity
4.5 L (1.18 US qt, 0.98 lmp.gal)
Carburetor
SAE 10W-30
SAE 10W-40
SAE 20W-40
SAE 20W-50
ZAUM00**
Weight:
Recommended engine oil classification
API Service SE, SF type or higher
with oil and full fuel tank:
109 kg (240 lb)
Final gear oil
Engine:
Engine type
Air-cooled 4-stroke, SOHC
Cylinder arrangement:
Forward-inclined single cylinder
Displacement:
125 cm3
Bore Stroke
51.5×60.0 mm (2.0×2.4 in)
Compression ratio:
9.8:1
Starting system:
Electric / kick starter
Lubrication system:
Wet sump
Type
SAE 85 W 140
Oil quantity
Engine oil
Periodic oil change
1.0 L (1.09 US qt, 0.92 lmp.qt)
Total amount
1.2 L (1.31 US qt, 1.10 lmp.qt)
Final gear case oil
Periodic oil change
0.13 L
Total amount
0.15 L
Type×quantity
BS26×1
Manufacturer
Mikuni
Spark plug
Type / Manufacturer
CR7E / NGK
Gap
0.7 ~ 0.8 mm (0.028 ~ 0.032 in)
Transmission
Primary reduction system
Helical gear
Primary reduction ratio
40/15(2.666)
Secondary reduction system
Spur gear
Secondary reduction ratio
38/13(2.923)
Transmission type
Single speed automatic(V-belt type)
Operation
Centrifugal automatic type
Chassis
Frame type
Steel tube underbone
Caster angle
32°
Trail
75 mm
Air filter
Paper type element
8-1
5YR-F8199-11ch8.pmd
1
2004/06/11, 14:13
SPECIFICATIONS
Front tire
Rear wheel
Type
Tubeless
Size
3.50-10 51J
Manufacturer
Cheng shin
Electrical system
Type
Cast
Size
J10×MT 2.5
Front brake
Type
Single disc brake
Operation
Right hand operation
Fluid
DOT 4
Rear tire
Type
Tubeless
Size
3.50-10 51J
Manufacturer
Cheng shin
Maximum load*
144 kg (317 lb)
Rear brake
Tire air pressure(Cold tire)
Up to 90 kg (198 lb) load*
Front
150 kPa(1.50 kg / cm2, 22 psi)
Rear
200 kPa(2.00 kg / cm2, 29 psi)
90 kg load ~ maximum load*
Front
150 kPa(1.50 kg / cm2, 22 psi)
Rear
225 kPa(2.25 kg / cm2,32 psi)
*Load is total weight of cargo, rider and accessories.
Front wheel
Type
Drum
Operation
Left hand operation
Front suspension
Type
Telescopic fork
Rear suspension
Type
Unit swing
Shock absorbers
Front
Coil spring / oil damper
Rear
Coil spring / oil damper
Wheel travel
Front
59 mm
Rear
54 mm
Type
Cast
Size
J10×MT 2.5
Ignition system
C.D.I.
Charging system
Type
C.D.I. magneto generator
Standard output
14 V,120W / 5,000 r/min
2
2
Battery
Type
GTX 7A-BS
Voltage, capacity
12 V, 6 AH
Headlight type
3
4
Bulb
Bulb voltage, wattage quantity
Headlight
12 V, 60 / 65 W×1
Tail / brake light
12 V, 8 / 27 W×1
Turn signal light
12 V, 10 W×4
Meter light
14 V, 3 W×1
Fuel meter light
14 V, 3 W×1
High beam indicator light
14 V, 3 W×1
Turn indicator light
12 V, 1.7 W×1
Fuse
10A 1
8-2
5YR-F8199-11ch8.pmd
1
2004/06/11, 14:13
5
6
7
8
9
CONSUMER INFORMATION
EAU26351
Identification numbers
1
2
3
EAU26390
Key identification number
Record the key identification number,
vehicle identification number and model
label information in the spaces provided
below for assistance when ordering
spare parts from a Yamaha dealer or for
reference in case the vehicle is stolen.
EAU26410
Vehicle identification number
1
1
KEY IDENTIFICATION NUMBER:
4
ZAUM00**
5
VEHICLE IDENTIFICATION NUMBER:
6
7
ZAUM00**
1. Key identification number
1. Vehicle identification number
The key identification number is
stamped into the key.
Record this number in the space provided and use it for reference when ordering a new key.
The vehicle identification number is
stamped into the frame.
NOTE:
The vehicle identification number is used
to identify your motorcycle and may be
used to register your motorcycle with
the licensing authority in your area.
MODEL LABEL INFORMATION:
8
9
9-1
5YR-F8199-11ch9.pmd
1
2004/06/11, 14:13
CONSUMER INFORMATION
EAU26460
Model label
1
1
2
3
4
ZAUM00**
1. Model label
5
The model label is affixed to the location shown. Record the information on
this label in the space provided. This
information will be needed when ordering spare parts from a Yamaha dealer.
6
7
8
9
9-2
5YR-F8199-11ch9.pmd
2
2004/06/11, 14:13
CONSUMER INFORMATION
EAU26550
Reporting safety defects
1
2
3
4
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation,
U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a
group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual
problems between you, your dealer, or Yamaha Motor Corporation, U.S.A.
To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in Washington, D.C.
area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information
about motor vehicle safety from the Hotline.
5
6
7
8
9
9-3
5YR-F8199-11ch9.pmd
3
2004/06/11, 14:13
CONSUMER INFORMATION
EAU26560
Motorcycle noise regulation
TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:
Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other
than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new
vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use
of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
1
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.
3
These acts include tampering with the following systems; i.e., modification, removal, etc.
2
4
5
6
Exhaust system
Muffler
Exhaust pipe
Silencer
Intake system
Air cleaner case
Air cleaner element
Intake duct
7
8
9
9-4
5YR-F8199-11ch9.pmd
4
2004/06/11, 14:13
CONSUMER INFORMATION
EAU26661
YAMAHA MOTOR CORPORATION, U.S.A.
STREET AND ENDURO MOTORCYCLE LIMITED WARRANTY
1
2
3
4
5
6
7
8
9
9-5
5YR-F8199-11ch9.pmd
5
2004/06/11, 14:13
CONSUMER INFORMATION
1
2
3
4
5
6
7
8
9
9-6
5YR-F8199-11ch9.pmd
6
2004/06/11, 14:13
CONSUMER INFORMATION
EAU26750
YAMAHA EXTENDED SERVICE (Y.E.S.)
1
2
3
4
5
6
7
8
9
9-7
5YR-F8199-11ch9.pmd
7
2004/06/11, 14:13
CONSUMER INFORMATION
1
2
3
4
5
6
7
8
9
9-8
5YR-F8199-11ch9.pmd
8
2004/06/11, 14:13
1
2
3
4
5
6
7
8
9
YAMAHA MOTOR TAIWAN CO., LTD
PRINTED IN TAIWAN
2004.06-0.8 1 !
(E)
5YR-F8199-11cv.pmd
2
2004/06/11, 14:14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement