Universal Remote Control URC-4041 User`s guide

Universal Remote Control URC-4041 User`s guide
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 1
DVD EXPERT
Universal Remote Control
URC-4041
User’s Guide
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 2
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features And Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Device Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Programming Device Control . . . . . . . . . . . . . . . . . . . . . . . . 9
Searching For Your Code . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Programming A Master Power Macro . . . . . . . . . . . . . . . . 12
Programming The Power Key For The Master Power Macro . . . 12
Operating The Master Power Macro . . . . . . . . . . . . . . . . . . . . 12
Clearing The Master Power Macro . . . . . . . . . . . . . . . . . . . . . 13
Using Keymover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programming Keymover . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Restoring Keymoved Keys To Default Settings. . . . . . . . . . . . . 14
Restoring A Single Keymoved Key . . . . . . . . . . . . . . . . . . . . . . 14
Restoring All Keymoved Keys In A Single Mode . . . . . . . . . . . . . 14
Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . . . . . . . . 14
Using Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Programming Favorite Channel Scan . . . . . . . . . . . . . . . 16
Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Locking Volume Control To One Mode
(Global Volume Lock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Unlocking Volume Control For A Single Device
(Individual Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Unlocking All Volume Control
(Restoring Default Setting ) . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Manufacturer’s Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setup Codes For Audio Amplifiers. . . . . . . . . . . . . . . . . . . . . . 18
Setup Codes For Audio Receivers . . . . . . . . . . . . . . . . . . . . . . 19
Setup Codes For Cable Boxes. . . . . . . . . . . . . . . . . . . . . . . . . 20
Setup Codes For DVD Players . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setup Codes For Home-Theater-In-A-Box Devices. . . . . . . . . . 22
Setup Codes For PVRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Setup Codes For Satellite Receivers . . . . . . . . . . . . . . . . . . . . 22
Setup Codes For Satellite Receiver/PVR Combos . . . . . . . . . . 23
Setup Codes For TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Setup Codes For TV/DVD Player Combos. . . . . . . . . . . . . . . . . 27
Setup Codes For TV/VCR Combos . . . . . . . . . . . . . . . . . . . . . . 27
Setup Codes For VCRs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Setup Codes For VCR/DVD Player Combos . . . . . . . . . . . . . . . 30
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Instructions To The User . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 3
INTRODUCTION
The One For All DVD Expert Universal Remote Control
(URC-4041) is designed to remotely operate up to four
home entertainment devices and features intuitive and
easy-to use buttons to operate a DVD component. Its
sophisticated technology will allow you to consolidate
your original home entertainment remote controls into
one easy-to-use product. Advanced features include:
• Intuitive buttons to allow easy access to functions
and menus on your DVD player and Home-TheaterIn-A-Box (HTIB) devices
• Direct code setup for easy device programming
• Step-and-Set code setup and Code Verification for an
alternate way to program devices
• Power macro for master on/off control of all of your
equipment with a single keystroke
• Volume Lock/Unlock feature to lock or unlock the
volume control to one mode or individual modes
• Device Key Re-Assignment to remotely control
a second (duplicate) device
• Favorite Channel Scan for easy channel surfing
• Color-coded keys to quickly locate popular functions
• Glow keys to aid operation when the ambient light
conditions are low
• Extensive code library for popular video and audio
devices including DVD players, PVR/DVRs, and
HTIB (Home-Theater-In-A-Box) devices.
The URC-4041 remote control requires two (2) new
AAA alkaline batteries (not included) and some easy
programming to control your devices. For best results,
please read and perform all instructions listed here.
Also, keep these instructions for future reference.
3
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 4
FEATURES AND FUNCTIONS
Use the illustration below to locate features on the
One For All DVD Expert Universal Remote Control
(URC-4041) and then study the Key Charts (on the next
two pages) to learn how they function.
To find out what type of devices can be controlled by
each device key after programming, see the Device
Table on page 7.
4
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 5
Key Charts
When the LED (red light) blinks, the
remote control is working and (after
programming) is sending signals.
Press DVD/VCR, AUX, CBL/SAT, or TV
once to select a desired home
entertainment device to control.
Also see the Device Table on page 7.
Press POWER once to turn on or off
the selected device. For master
power control, see Programming
A Master Power Macro on page 12.
Use the keypad (1 ~ 9 and 0) to
directly select channels (e.g., 009
or 031).
Use TV/VID to switch the TV’s input
to view TV or video programs.
Press ENTER once after entering
the channel numbers on some TVs.
Use GUIDE to display your selected
device’s program guide or setup
menu.
Press MENU once to display your
selected device’s main menu.
Use INFO/OSD to display the current
channel and program information
or on-screen directory.
Use EXIT to exit from your selected
device’s guide or menu.
Use the Cursor Keys to move the
cursor in the program guide and
menu screens.
Use SELECT to choose options from
your selected device’s menu or guide.
Press LAST once to recall the last
channel. For PVRs, use LAST to
select live or recorded video.
Use FAV to scan through all channels,
or after programming, to scan
through 10 favorite channels.
continued on next page...
5
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 6
FEATURES AND FUNCTIONS
Key Charts (continued)
Use CH▲ (or CH▼) to select the
next higher (or lower) channel.
Press MUTE once to turn the sound
off or on.
In the DVD mode, press REPEAT
once to replay a selected chapter
(after pressing TITLE - see below).
Use VOL▲ (or VOL▼) to raise (or
lower) the sound volume.
Use SLEEP to set the sleep timer on
a selected device if equipped with
this feature.
Use ANGLE to perform the angle
function on your DVD player.
Use AUDIO to select an alternate
audio channel (e.g., Spanish), if
available on your cable/satellite
service or DVD.
Press TITLE once to display (or turn
off) a DVD’s title information (e.g.,
chapters, settings, etc.) if available.
In the DVD mode, press ZOOM once
to zoom in on (or out of) a viewed
picture, if the function is available
on your DVD device.
Press SUBTITLE/CC once to display
(or turn off) subtitles or closed
captions, if available on your DVD
or cable/satellite service.
Use REW, PLAY, FWD, F.REW, PAUSE,
F.FWD, or STOP to control your VCR,
PVR, DVD player, or VOD (Video
On Demand) if available on
your cable/satellite service.
Press REC twice to record a PVR or
VCR program.
Use SET for all programming
sequences.
6
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 7
Device Table
NOTE: Please refer to the table below when performing the
instructions in “Programming Device Control” on page 9.
After programming, the One For All DVD Expert
Universal Remote Control will be able to control the
following types of devices:
DEVICE KEY
CONTROLS THESE TYPES OF DEVICES
DVD Players, TV/DVD Player Combos,VCRs,
TV/VCR Combos,VCR/DVD Player Combos,
Home-Theater-In-A-Box devices, or
PVR/DVRs (Personal or Digital Video
Recorders)
Audio Amplifiers or Receivers; also use for
second VCR or DVD player (see page 14,
Re-Assigning Device Keys).
Cable Boxes (Converters), Satellite Receivers,
or Satellite/PVR Combos
Televisions
7
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 8
INSTALLING BATTERIES
❶
❷
❷
❸
1.
On the remote control’s back, push the tab
and lift off the battery cover.
2.
Obtain two (2) new AAA alkaline batteries.
Match the + and – marks on the batteries
to the + and – marks in the battery case,
then insert the new batteries.
3.
Press the battery cover back into place.
The tab should click when the cover is
locked.
4.
Test the remote control by pressing
any mode key (e.g., TV). If the batteries are
inserted correctly, the LED (red light) will
blink once.
NOTE: When batteries need replacement, the remote control
will stop operating. Remove the old batteries and insert new
ones within 10 minutes to ensure all of your programming
information is restored.
8
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 9
PROGRAMMING DEVICE CONTROL
The One For All DVD Expert Universal Remote Control
is preprogrammed at the factory to operate an RCA TV,
a Toshiba DVD player, a Motorola cable box, and a
Pioneer audio receiver/amplifier. To control devices other
than the default brands, perform the following steps;
otherwise skip this section:
1.
Turn on a desired device (e.g.,VCR or
DVD player) and, if applicable, insert
media (e.g., cassette or disc).
NOTE: Please read steps 2 through 4 completely
before proceeding. Highlight or write down the
codes and device you wish to program before
starting step 2.
2.
On the remote control,press a device key
once (i.e., DVD/VCR, AUX, CBL/SAT,or TV).
NOTE: To program control of a DVD device,
VCR, PVR (or DVR), VCR/DVD Combo, or
Home-Theater-In-A-Box device, press
DVD/VCR once.
NOTE: To program control of an Audio
Amplifier or Receiver, press AUX once.
NOTE: To program control of a Cable Box,
Satellite Receiver, or a Satellite Receiver/PVR
(or DVR) Combo, press CBL/SAT once.
NOTE: To program control of a TV/VCR Combo,
press DVD/VCR once. After programming, you
will be able to control channel selection, volume,
and VCR functions.
NOTE: To program control of a TV/DVD Player
Combo, press DVD/VCR once. After programming, you will be able to control channel
selection, volume, and DVD functions.
3.
Press and hold SET until the LED (red light)
blinks twice, then release SET.
4.
Use the Manufacturer’s Codes (starting on
page 18) to locate the type of device and
brand name and then enter the first fourdigit code for your device. If performed
correctly, the LED will blink twice.
NOTE: If the LED did not blink twice, repeat steps
2 through 4 and enter the same code again.
continued on next page...
9
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 10
PROGRAMMING DEVICE CONTROL
(continued)
5.
Aim the remote control at the device and
press POWER once. The device should turn
off. If it does not, repeat steps 2 through 5
(starting on the previous page), trying
each code for your brand until you find
one that works. If it still doesn’t work, try
Searching For Your Code below.
NOTE: If the device does not have a POWER
key, press the (Play) key.
6.
Repeat steps 1 through 5 (starting on the
previous page) for each device you want to
control.For future reference,write down
each working device code in the following
boxes:
DVD/VCR Code:
Device Type:____________________
AUX Code:
Device Type:____________________
CBL/SAT Code:
Device Type:____________________
TV Code:
SEARCHING FOR YOUR CODE
If your device does not respond to the remote control
after trying all codes listed for your brand, or if your
brand is not listed at all, try searching for your code.
NOTE: Before performing a code search for a CD or DVD player
or a VCR, turn on the device and insert the required media.
For example, to search for a code for your TV:
1.
On the remote control, press TV once.
2.
Press and hold SET until the LED (red light)
blinks twice, then release SET.
3.
Enter 9 - 9 - 1. The LED will blink twice.
10
IMPVE4P manual 1.0
4.
4/11/03
4:34 PM
Page 11
Aim the remote control at the TV and
slowly alternate between pressing POWER
and TV. Stop when the TV turns off (after
pressing POWER).
NOTE: In the search mode, the remote control
will send IR codes from its library to the selected
device, starting with the most popular code first.
5.
To lock in the code, press and release SET.
The LED will blink twice.
6.
To search for the codes of your other
devices, repeat steps 1 through 5, but
substitute the appropriate device key for
the device you are searching for.
CHECKING THE CODES
If you have set up the remote control using the
Searching For Your Code procedure (on the previous
page), you may need to find out which four-digit code
is operating your equipment.
For example,to find out which code is operating your TV:
1.
On the remote control, press TV once.
2.
Press and hold SET until the LED (red light)
blinks twice, then release SET.
3.
Enter 9 - 9 - 0. The LED will blink twice.
4.
To view the code for the first digit, press 1
once.Wait 3 seconds, count the LED
blinks (e.g., three blinks = 3) and write
down the number in the leftmost box in
the TV code boxes on page 10.
NOTE: If a code digit is “0”, the LED will not
blink.
5.
Repeat step 4 three more times for
remaining digits. Use 2 for the second
digit, 3 for the third digit, and 4 for the
fourth digit.Write down the code digits in
the remaining TV code boxes on page 10.
6.
To check for codes of other devices, repeat
steps 1 through 5, but substitute the
appropriate device key for each device you
are checking.Write down the device’s code
digits in the appropriate code boxes on
page 10.
11
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 12
PROGRAMMING A MASTER POWER MACRO
In its default state, the POWER key on the One For All
DVD Expert Universal Remote Control will individually
power your home entertainment devices on or off.
However, you can also program a Master Power Macro
onto the POWER key that will sequentially turn on or off
all the devices with a single key press.
Programming The Power Key For The Master
Power Macro
1.
Press and hold SET until the LED (red light)
blinks twice, then release SET.
2.
Enter 9 - 9 - 5. The LED will blink twice.
Then press POWER once.
3.
For the first device you want in the poweron sequence, press its device key (e.g.,
CBL/SAT) once.
4.
Repeat step 3 up to three more times to
add desired devices to the power-on
sequence.
5.
To save the settings and exit the program,
press and hold SET until the LED blinks
twice, then release SET.
Operating The Master Power Macro
1.
After programming, point the remote
control at the devices and press POWER
for at least 2 seconds to sequentially turn
on or off your devices.
NOTE: When POWER is pressed for less than
2 seconds, a power command will only be sent
to the currently-selected device. This allows you
to still individually power devices on or off.
2.
You will see the devices turn on or off
according to your programmed sequence.
NOTE: The currently-selected device will always
turn on or off first, followed by the remaining
programmed sequence. After the master power
sequence has been completed, the remote control
will be set to control the first powered-on device.
NOTE: If one or more devices does not have a
POWER key, the power off/on sequence may be
slightly delayed when the remote control signals
the device(s). This action is normal.
12
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 13
Clearing The Master Power Macro
1.
Press and hold SET until the LED (red light)
blinks twice, then release SET.
2.
Enter 9 - 9 - 5. The LED will blink twice.
Then press POWER once.
3.
Press and hold SET until the LED blinks
twice, then release SET. The Master Power
Macro is now cleared.
USING KEYMOVER
The One For All DVD Expert Universal Remote Control
includes a Keymover feature that allows you to map
(or copy) keys from one mode (i.e., source mode) to
another mode (i.e., destination mode).
NOTE: The following keys should not be used as a source or
destination: DVD/VCR, AUX, CBL/SAT, TV, SET, FAV, and REC.
Programming Keymover
For example, if your DVD player does not have volume
control, you can map those keys (i.e., VOL ▲, VOL▼, and
MUTE) from TV mode to DVD/VCR mode as follows:
1.
Press and hold SET until the LED (red light)
blinks twice, then release SET.
2.
Enter 9 - 9 - 4. The LED will blink twice.
3.
For the source mode, press TV once.
4.
For the source key, press VOL ▲ once.
5.
For the destination mode, press DVD/VCR
once.
6.
For the destination key, press VOL ▲ once.
7.
The LED will blink twice, indicating the
keymoved sequence is correct.
8.
Repeat steps 1 through 7 twice more to
map remaining volume control keys,
substituting VOL▼ and MUTE as source and
destination keys in steps 4 and 6.
13
continued on next page...
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 14
USING KEYMOVER
Programming Keymover (continued)
Upon completion of the above procedure, you can now
use your One For All DVD Expert Universal Remote
Control to control the TV’s volume and mute in the
DVD mode, as well as in the TV mode.
Restoring Keymoved Keys to Default Settings
Restoring A Single Keymoved Key
1.
Press a device key that has a keymoved key.
2.
Press and hold SET until the LED (red light)
blinks twice, then release SET.
3.
Enter 9 - 9 - 4. The LED will blink twice.
4.
Press the destination key twice (where the
keymoved key is stored). The LED will
blink twice.
Restoring All Keymoved Keys In A Single Mode
1.
Press and hold SET until the LED (red light)
blinks twice, then release SET.
2.
Enter 9 - 9 - 4. The LED will blink twice.
3.
Press the destination mode twice (where
keymoved keys are stored). The LED will
blink twice.
RE-ASSIGNING DEVICE KEYS
The One For All DVD Expert Universal Remote Control
can be set to control a second TV, PVR,VCR, DVD player,
or other device. For example, to control a TV, a cable box,
and two DVD players, re-assign the unused AUX key to
operate the second DVD player as follows:
1.
On the remote control, press and hold SET
until the LED (red light) blinks twice, then
release SET.
2.
Enter 9 - 9 - 2. The LED will blink twice.
14
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 15
3.
Press DVD/VCR once, then press AUX once.
The LED will blink twice.
4.
The AUX key is now ready to be set up to
control your second DVD player. See
Programming Device Control on page 9.
To re-assign other device keys to the AUX key, repeat
steps 1 through 4 with a sequence from the below chart:
NOTE: Only one device can be assigned to an unused device
key at a time.
To Re-Assign Device
Perform Sequence
AUX as 2nd TV key:
SET - 9 - 9 - 2 - TV - AUX
AUX as 2nd CBL/SAT key:
SET - 9 - 9 - 2 - CBL/SAT - AUX
When a re-assignment is done, the LED will blink twice
to confirm your choice.At that time, you will need to
program the remote control for the new device (see
Programming Device Control on page 9).
USING CHANNEL SCAN
In the DVD/VCR, CBL/SAT, or TV mode, use the FAV key to
start a 3-second scan of all channels. If programmed,
use the FAV key to scan only your favorite channels to
view a desired channel (see Programming Favorite
Channel Scan on next page. )
1.
If Favorite Channel Scan has been set up,
skip to step 2. Otherwise, press DVD/VCR,
CBL/SAT, or TV once.
2.
Press FAV once.
• If Favorite Channel Scan has been set up,
scanning of favorite channels will start
and cycle through stored channels for
3 minutes or until stopped by pressing
any key.
• If Favorite Channel Scan has not been
set up, scanning will start with the
current channel, then proceed to the
next channel up and cycle through all
channels for 3 minutes or until stopped
by pressing any key.
3.
To stop scanning channels at any time,
press any key once.
15
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 16
PROGRAMMING FAVORITE CHANNEL SCAN
In the DVD/VCR, CBL/SAT, or TV mode, you can store a list
of up to 10 favorite channels, in any order, that will be
immediately scanned when FAV is pressed (see Using
Channel Scan on the previous page).
NOTE: Favorite channels can only be programmed for one
mode. After programming, if FAV is pressed while in another
mode, the remote control will start scanning all channels
instead (if applicable to the selected device).
1.
On the remote control, press DVD/VCR,
CBL/SAT, or TV once.
2.
Press and hold SET until the LED (red light)
blinks twice, then release SET.
3.
Enter 9 - 9 - 6. The LED will blink twice.
4.
Use the keypad to enter a favorite channel
number (e.g., 031). Then press SET once.
NOTE: If the original remote control required
pressing an Enter key to change the channel,
also press the ENTER key after the channel
number (e.g., 0 - 3 - 1 - ENTER).
5.
If desired, repeat step 4 for each channel
to be stored, up to a total of 10 channels.
NOTE: If you try entering more than
10 channels, the remote control will
automatically exit programming.
6.
To exit programming with less than
10 favorite channels stored, press and hold
SET until the LED blinks twice. Otherwise,
the remote control will automatically exit
the program after ten channels have been
stored.
16
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 17
CHANGING VOLUME LOCK
The One For All DVD Expert Universal Remote Control
is set at the factory for independent volume control of
each selected device.
However, you may change the Volume Lock setting to
Global Volume Lock so that a device’s volume will be
locked to one mode (e.g., to control TV volume in all
other modes).After that, if desired, you can perform
Individual Volume Unlock on a selected device to set its
volume control for independent operation.
Locking Volume Control To One Mode
(Global Volume Lock)
1.
Press and hold SET until the LED (red light)
blinks twice, then release SET.
2.
Enter 9 - 9 - 3 and then press any
mode key once (e.g., TV). The LED will
blink twice.
3.
Now, when you press VOL ▲, VOL▼, or
MUTE, the volume of the selected device
(e.g., TV) will be controlled, regardless of
the mode you have selected.
Unlocking Volume Control For A Single Device
(Individual Volume Unlock)
1.
After performing Global Volume Lock (on
page 16),press a desired mode key where
you want volume to be unlocked (e.g.,
AUX) and controlled within its own mode.
2.
Press and and hold SET until the LED (red
light) blinks twice,then release SET.
3.
Enter 9 - 9 - 3 and then press VOL▼ once.
The LED will blink four times.
4.
If desired, repeat steps 1 through 3
(of this section) for each device that you
want volume to be unlocked.
5.
Now, after you select a device that has
volume unlocked (e.g., AUX), pressing
VOL ▲, VOL▼, or MUTE will control the
device’s volume only in its own mode.
continued on next page...
17
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 18
CHANGING VOLUME LOCK (continued)
Unlocking All Volume Control (Restoring
Default Setting)
NOTE: Performing these instructions will restore independent
volume control for all programmed devices (e.g., TV volume
control in TV mode, VCR volume in DVD/VCR mode, etc.).
1.
On the remote control, press and hold SET
until the LED (red light) blinks twice,then
release SET.
2.
Enter 9 - 9 - 3 and then press VOL ▲ once.
The LED will blink four times.
3.
Volume will again be independently
controlled according to its default states
for all programmed devices.
MANUFACTURER’S CODES
Setup Codes For Audio Amplifiers
Aiwa
Bose
Carver
Curtis Mathes
Denon
GE
Harman/Kardon
JVC
Left Coast
Linn
Luxman
Magnavox
Marantz
NEC
Nakamichi
Optimus
Panasonic
Parasound
Philips
Pioneer
Polk Audio
RCA
0406
0674
0269
0300
0160
0078
0892
0331
0892
0269
0165
0269
0892, 0321, 0269
0264
0321
0395, 0300
0308, 0521
0246
0892, 0269
0013, 0300
0892, 0269
0300
18
IMPVE4P manual 1.0
Realistic
Sansui
Shure
Sony
Soundesign
Technics
Victor
Wards
Yamaha
4/11/03
4:34 PM
Page 19
0395
0321
0264
0689, 0220
0078, 0211
0308, 0521
0331
0078, 0013, 0211
0354, 0133
Setup Codes For Audio Receivers
Aiwa
Arcam
Carver
Denon
Garrard
Harman/Kardon
Integra
JBL
JVC
Kenwood
Linn
MCS
Magnavox
Marantz
Nakamichi
Onkyo
Optimus
Panasonic
Philips
Polk Audio
Quasar
Sansui
Sanyo
Sharp
Sony
Soundesign
Teac
Technics
Victor
Wards
Yamaha
Zenith
0121, 0158, 0189, 0405
1120
0189
0004
0463
0110, 0189, 1304
0135
0110
0074
0027, 0186
0189
0039
0189, 0391
0039, 0189
0097
0135
0186, 0670
0039, 0309
0189, 0391, 1120
0189
0039
0189
1251
0186
0158
0670
0463
0039, 0309
0074
0158, 0189
0176, 0186
0857
19
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 20
MANUFACTURER’S CODES (continued)
Setup Codes For Cable Boxes
ABC
Americast
Bell & Howell
Bell South
Director
General Instrument
GoldStar
Hamlin
Jerrold
Memorex
Motorola
Pace
Panasonic
Paragon
Philips
Pioneer
Pulsar
Quasar
Regal
Runco
Samsung
Scientific Atlanta
Sony
Starcom
Supercable
Tocom
Torx
Toshiba
Zenith
0003, 0008, 0014, 0017
0899
0014
0899
0476
0476, 0003, 0276, 0810
0144
0009, 0273
0476, 0003, 0276, 0012, 0014, 0810
0000
0476, 0276, 0810
0237
0000, 0107
0000
0305, 0317
0877, 0144, 0533, 1877
0000
0000
0273, 0279
0000
0144
0877, 0008, 0017, 0477, 1877
1006
0003
0276
0012
0003
0000
0000, 0525, 0899
Setup Codes For DVD Players
Aiwa
Apex Digital
Blaupunkt
Blue Parade
Broksonic
DVD2000
Daewoo
Denon
Emerson
Enterprise
Fisher
GE
0641
0672, 0717, 0755, 0794, 0796, 0797, 0830, 0856,
1100
0717
0571
0695, 0868
0521
0784
0490, 0634
0591
0591
0670
0522, 0717, 0815
20
IMPVE4P manual 1.0
Go Video
Gradiente
Greenhill
Harman/Kardon
Hitachi
Hiteker
IRT
Integra
JBL
JVC
KLH
Kenwood
Koss
Lasonic
Magnavox
Malata
Marantz
Memorex
Microsoft
Mintek
Mitsubishi
Nesa
Norcent
Onkyo
Oritron
Panasonic
Philips
Pioneer
Polk Audio
Proscan
Qwestar
RCA
Raite
Rotel
Samsung
Sansui
Sanyo
Sharp
Shinsonic
Sony
Sylvania
Technics
Theta Digital
Toshiba
Tredex
Urban Concepts
XBox
4/11/03
4:34 PM
Page 21
0715, 0783
0651
0717
0582, 0702
0573, 0664
0672
0783
0627
0702
0558, 0623
0717
0490, 0534, 0682, 0737
0651
0798
0503, 0675
0782
0539
0831
0522
0717, 0839
0521
0717
0872, 0895
0503, 0627
0651
0490, 0632, 0703, 0824, 1490
0503, 0539, 0646, 0854
0525, 0571, 0632, 0638
0539
0522
0651
0522, 0571, 0717, 0822
0665
0623
0573, 0820
0695
0670, 0695
0630
0533, 0839
0533, 0864
0675, 0821
0490, 0703
0571
0503, 0695
0799
0503
0522
continued on next page...
21
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 22
MANUFACTURER’S CODES
Setup Codes For DVD Players (continued)
Yamaha
Yamakawa
Zenith
0490, 0539, 0545, 0817
0665
0503, 0591, 0741
Setup Codes For
Home-Theater-In-A-Box Devices
Aiwa
Alco
Anam
Apex Digital
Audiovox
Daewoo
Fisher
Integra
JVC
KLH
Koss
Marantz
Norcent
Onkyo
Oritron
Panasonic
Pioneer
Polk Audio
RCA
Samsung
Sony
Venturer
1388, 1641
1390
1609
1257
1390
1250
1801
1298
1374
1390
1366
1289
1923
1298
1366
1288, 1316, 1763, 1764
1384
1289
1390, 1609
1295
1558, 1658, 1758
1390
Setup Codes For PVRs
Panasonic
Philips
ReplayTV
Sonic Blue
Sony
Tivo
0616
0618
0616
0616
0636
0618, 0636
Setup Codes For Satellite Receivers
AlphaStar
Chaparral
Crossdigital
DirecTV
0772
0216
1109
0392, 0566, 0639, 1142, 0247, 0749, 0819, 1109,
1749
22
IMPVE4P manual 1.0
4/11/03
Dish Network System
DishPro
Echostar
Expressvu
GE
GOI
General Instrument
HTS
Hitachi
Hughes Network Systems
JVC
Magnavox
Memorex
Mitsubishi
Motorola
Next Level
Panasonic
Paysat
Philips
Proscan
RCA
RadioShack
SKY
Samsung
Sony
Star Choice
Toshiba
UltimateTV
Uniden
Zenith
4:34 PM
Page 23
1005, 0775, 1775
1005, 0775, 1775
1005, 0775, 1775
0775, 1775
0566
0775
0869
0775
0819
1142, 0749, 1749, 1242
0775
0724, 0722
0724
0749
0869
0869
0247, 0701
0724
1142, 0749, 0724, 1076, 0722, 1749, 1242
0392, 0566, 1392
0392, 0566, 0855, 0143, 1392
0869
0856
1109, 1276
0639, 1639
0869
0749, 0790, 1749
0392, 0639, 1392
0724, 0722
0856, 1856
Setup Codes For Satellite Receiver/
PVR Combos
Echostar
Expressvu
Hughes Network Systems
Philips
Proscan
RCA
Sony
1005, 1775, 0775
1775, 0775
1242, 1142
1242, 1142
1392, 0392
1392, 0392
0639, 1639
Setup Codes For TVs
AOC
Admiral
Aiko
Aiwa
0030
0093, 0463
0092
0701
continued on next page...
23
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 24
MANUFACTURER’S CODES
Setup Codes For TVs (continued)
Akai
Alaron
America Action
Anam
Apex Digital
Audiovox
Baysonic
Bell & Howell
Bradford
Broksonic
CXC
Candle
Carnivale
Carver
Celebrity
Celera
Changhong
Cineral
Citizen
Clarion
Concerto
Contec
Craig
Crosley
Crown
Curtis Mathes
Daewoo
Denon
Dumont
Electroband
Emerson
Envision
Fisher
Fujitsu
Funai
Futuretech
GE
Gibralter
GoldStar
Gradiente
Grunpy
Hallmark
Harley Davidson
Harman/Kardon
0030
0179
0180
0180
0748, 0765, 0767
0451, 0180, 0092, 0623
0180
0154, 0016
0180
0236, 0463
0180
0030, 0056
0030
0054
0000
0765
0765
0451, 0092
0060, 0030, 0056, 0092
0180
0056
0180
0180
0054
0180
0047, 0054, 0154, 0451, 0093, 0060, 0030, 0145,
0056, 0016, 0166, 1147, 1347
0451, 0092, 0623
0145
0017
0000
0154, 0236, 0463, 0180, 0178, 0179, 0623
0030
0154
0179, 0683
0180, 0179, 0171
0180
0047, 0051, 0451, 0178, 0021, 1147, 1347
0017, 0030
0030, 0178
0053, 0056
0180, 0179
0178
0179
0054
24
IMPVE4P manual 1.0
Harvard
Havermy
Hitachi
IRT
Infinity
Inteq
JBL
JCB
JVC
KEC
KTV
Kenwood
Konka
LG
LXI
Logik
Luxman
MGA
MTC
Magnavox
Majestic
Marantz
Matsushita
Megatron
Memorex
Midland
Minutz
Mitsubishi
Motorola
Multitech
NAD
NEC
NTC
Nikko
Onwa
Optimus
Optonica
Orion
Panasonic
Penney
Philco
Philips
Pilot
Pioneer
Portland
Princeton
Prism
4/11/03
4:34 PM
Page 25
0180
0093
0145, 0056, 0016, 1145
0628
0054
0017
0054
0000
0463, 0053
0180
0180, 0030
0030
0628, 0632, 0638, 0703, 0707
0056
0047, 0054, 0154, 0156, 0178
0016
0056
0150, 0030, 0178
0060, 0030, 0056
0054, 0030, 0179, 1254, 1454
0016
0054, 0030
0250
0178, 0145
0154, 0250, 0463, 0150, 0178, 0179, 0016
0047, 0017, 0051
0021
0093, 0150, 0178
0093
0180
0156, 0178, 0166, 0866
0030, 0056
0092
0030, 0178, 0092
0180
0154, 0250, 0166
0093
0236, 0463, 0179
0250, 0051
0047, 0156, 0051, 0060, 0030, 0178, 0021, 1347
0054, 0463, 0030, 0145
0054, 1454
0030
0166, 0679, 0866
0092
0717
0051
continued on next page...
25
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 26
MANUFACTURER’S CODES
Setup Codes For TVs (continued)
Proscan
Proton
Pulsar
Quasar
RCA
RadioShack
Realistic
Runco
SSS
Sampo
Samsung
Sansei
Sansui
Sanyo
Scotch
Scott
Sears
Semivox
Semp
Sharp
Signature
Sony
Soundesign
Squareview
Starlite
Supreme
Sylvania
Symphonic
TMK
TNCi
TVS
Tandy
Technics
Technol Ace
Techwood
Teknika
Telefunken
Toshiba
Vector Research
Victor
Vidikron
Vidtech
Wards
Waycon
0047
0178
0017
0250, 0051
0047, 0090, 0679, 1047, 1147, 1247, 1347, 1447
0047, 0154, 0180, 0030, 0178, 0056
0154, 0180, 0030, 0178, 0056
0017, 0030, 0603
0180
0030
0060, 0030, 0178, 0056
0451
0463
0154
0178
0236, 0180, 0178, 0179
0047, 0054, 0154, 0156, 0178, 0179, 0056, 0171
0180
0156
0093, 0688
0016
0000
0180, 0178, 0179
0171
0180
0000
0054, 0030, 0171
0180, 0171
0178, 0056
0017
0463
0093
0250, 0051
0179
0051, 0056
0054, 0180, 0150, 0060, 0179, 0056, 0016, 0092
0056
0154, 0156, 0060, 1256, 1356
0030
0053
0054
0178
0054, 0030, 0178, 0021, 0179, 0056, 0016, 0866
0156
26
IMPVE4P manual 1.0
White Westinghouse
Yamaha
Zenith
4/11/03
4:34 PM
Page 27
0463, 0623
0030
0017, 0463, 0178, 0016, 0092
Setup Codes For TV/DVD Player Combos
Apex Digital
Broksonic
Panasonic
Philips
Sharp
Sylvania
Toshiba
0830
0695, 0868
1490
0854
0630
0821
0695
Setup Codes For TV/VCR Combos
Broksonic
Citizen
Daewoo
Emerson
Funai
GE
GoldStar
Harley Davidson
Hitachi
Lloyd’s
Magnasonic
Magnavox
Memorex
Mitsubishi
Optimus
Orion
Panasonic
Penney
Quasar
RCA
Sansui
Sears
Sharp
Sony
Sylvania
Symphonic
Thomas
Toshiba
White Westinghouse
Zenith
1479
1278
1278
1278, 1479
0000
1035, 0807, 1060
1237
0000
0000
0000
1278
0000, 1781
0037, 1162, 1237
0807
1162
1479
1035, 1162
1035
1035, 1162
0807, 1035, 1060
0000, 1479
0000, 1237
0807
0000, 1232
1781
0000
0000
0845
1278
0000, 1479
27
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 28
MANUFACTURER’S CODES (continued)
Setup Codes For VCRs
Admiral
Adventura
Aiwa
American High
Asha
Audiovox
Beaumark
Bell & Howell
Broksonic
Calix
Canon
Carver
Citizen
Craig
Curtis Mathes
Cybernex
Daewoo
Denon
Dynatech
Electrohome
Electrophonic
Emerex
Emerson
Fisher
Fuji
Funai
GE
Garrard
GoldStar
Gradiente
HI-Q
Harley Davidson
Harman/Kardon
Hitachi
Hughes Network Systems
JVC
KEC
Kenwood
Kodak
LXI
Lloyd’s
MEI
MGA
MGN Technology
MTC
0048, 0209
0000
0037, 0000
0035
0240
0037
0240
0104
0184, 0121, 0209, 1479
0037
0035
0081
0037, 1278
0037, 0047, 0240
0060, 0035, 0162, 1035
0240
0045, 1278
0042
0000
0037
0037
0032
0037, 0184, 0000, 0121, 0043, 0209, 1278, 1479
0047, 0104
0035
0000
0060, 0035, 0240, 0807, 1035, 1060
0000
0037, 1237
0000
0047
0000
0081
0000, 0042
0042
0067
0037
0067
0035, 0037
0037
0000
0035
0240, 0043
0240
0240, 0000
28
IMPVE4P manual 1.0
Magnasonic
Magnavox
Magnin
Marantz
Marta
Matsushita
Memorex
Minolta
Mitsubishi
Motorola
Multitech
NEC
Nikko
Noblex
Olympus
Optimus
Orion
Panasonic
Penney
Pentax
Philco
Philips
Pilot
Pioneer
Polk Audio
Profitronic
Proscan
Pulsar
Quasar
RCA
RadioShack
Radix
Randex
Realistic
ReplayTV
Runco
STS
Samsung
Sanky
Sansui
Sanyo
Scott
Sears
Semp
Sharp
Shogun
Sonic Blue
4/11/03
4:34 PM
Page 29
1278
0035, 0039, 0081, 0000, 1781
0240
0035, 0081
0037
0035, 0162
0035, 0162, 0037, 0048, 0039, 0047, 0240, 0000,
0104, 0209, 1162, 1237
0042
0067, 0043, 0807
0035, 0048
0000
0104, 0067
0037
0240
0035
1062, 0162, 0037, 0048, 0104, 1162
0184, 0209, 1479
1062, 0035, 0162, 0225, 0616, 1035, 1162
0035, 0037, 0240, 0042, 1035, 1237
0042
0035, 0209
0035, 0081, 0618
0037
0067
0081
0240
0060, 1060
0039
0035, 0162, 1035, 1162
0060, 0240, 0042, 0807, 1035, 1060
0000
0037
0037
0035, 0037, 0048, 0047, 0000, 0104
0616
0039
0042
0240, 0045
0048, 0039
0000, 0067, 0209, 1479
0047, 0240, 0104
0184, 0045, 0121, 0043
0035, 0037, 0047, 0000, 0042, 0104, 1237
0045
0048, 0807
0240
0616
continued on next page...
29
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 30
MANUFACTURER’S CODES
Setup Codes For VCRs (continued)
Sony
Sylvania
Symphonic
TMK
Teac
Technics
Teknika
Thomas
Tivo
Toshiba
Totevision
Unitech
Vector
Video Concepts
Videomagic
Videosonic
Villain
Wards
White Westinghouse
XR-1000
Zenith
0035, 0032, 0000, 0636, 1232
0035, 0081, 0000, 0043, 1781
0000
0240
0000
0035, 0162
0035, 0037, 0000
0000
0618, 0636
0045, 0043, 0845
0037, 0240
0240
0045
0045
0037
0240
0000
0060, 0035, 0048, 0047, 0081, 0240, 0000, 0042
0209, 1278
0035, 0000
0039, 0000, 0209, 1479
Setup Codes For VCR/DVD Player Combos
Go Video
Samsung
Sansui
Sony
Toshiba
0715
0820
0695
0864
0503
30
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 31
TROUBLESHOOTING
PROBLEM:
LED (red light) does not blink when you
press a key.
SOLUTION: Replace batteries with two new AAA
alkaline batteries.
PROBLEM: LED blinks when you press a key, but
home entertainment device does not
respond.
SOLUTION: Make sure the remote control is aimed at
your home entertainment device and is
not farther than 15 feet away.
PROBLEM: The unit does not control home entertainment devices or commands are not
working properly.
SOLUTION: Try all listed codes for the device brands
being set up. Make sure they can be
operated with an infrared remote control.
PROBLEM: Changing channels does not work
properly.
SOLUTION: If the original remote control required
pressing ENTER to change channels,
then press ENTER on the remote control
after entering the channel number.
PROBLEM: Tried Searching For Your Code method
and still could not find a working code.
SOLUTION: Clear the device key as follows: Press and
hold SET until the LED (red light) blinks
twice, then release. Next enter 9 - 9 - 2.
Then press the device key to be cleared
twice. Now repeat the Searching For Your
Code method on page 10.
PROBLEM: CH ▲ and CH ▼ do not work for your
RCA TV.
SOLUTION: Due to RCA design (1983-1987), only the
original remote control will operate these
functions.
PROBLEM: No remote control of volume.
SOLUTION: See Changing Volume Lock on page 16 to
lock/unlock volume.
PROBLEM: If the above does not work.
SOLUTION: Please contact us in any of the
following ways:
• Please visit : www.oneforall.com
• If the above website is not able to
provide you with the information you
need, please email us at
[email protected]
• Customer Support : (330) 405-8612
31
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 32
INSTRUCTIONS TO THE USER
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide a reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiated radio frequency
energy and if not installed and used in accordance
with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet or a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help
32
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 33
LIFETIME WARRANTY
One For ALL ("OFA") warrants this product to be free
from defects in materials and workmanship, under
normal use, throughout the period of the product’s
ownership by the original purchaser. This warranty
does not cover damage or failures caused by products
or services not supplied by OFA, or which result from
accident, misuses, abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustment,
improper maintenance, alteration, maladjustment of
consumer controls, modifications, commercial use, or
that is attributable to acts of God.
There are no express warranties except as listed above.
OFA SHALL NOT BE LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THIS PRODUCT OR ARISING OUT OF
ANY BREACH OF WARRANTY,ALL EXPRESS AND
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE,ARE LIMITED TO
THE WARRANTY PERIOD SET FORTH ABOVE. Some
states do not allow the exclusion or limitation of incidental or consequential damagers, or limitations on
how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have
other rights which vary from state to state.
To obtain warranty service for a defective product,
please return the product, preferably in the original
carton, along with your purchase receipt, to the store of
original purchase for the first 90 days.A note detailing
the complaint would be helpful. The store, at its option,
will replace or repair this product if found to be defective.
If the unit has been purchased more than 90 days ago,
pls return it to Impact Distribution Services, 6262
Patterson Pass Road, Suite C, Livermore, CA 94550
together with the original receipt and $3.95 to cover
postage and handling. It will be repaired or replaced at
the manufacturer’s option. The manufacturer reserves
the right to substitute a currently manufactured model
with equal or superior features.
One For All: (330) 405-8655
URC-4041
April 2003
33
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 34
ADDITIONAL INFORMATION
As you update your home entertainment system, One
For All® has a universal remote control that will fit your
needs. Look for these exciting products at a retailer
near you.
One For All Access 3 . . . . . . . . . . . . . . . . . . . . . URC-3605
One For All Big Easy 3-Device. . . . . . . . . . . . . URC-3300
One For All DVD Expert 4-Device . . . . . . . . . URC-4041
One For All Big Easy 4-Device. . . . . . . . . . . . . URC-4330
One For All Access 4 . . . . . . . . . . . . . . . . . . . . . URC-4605
One For All Access 5 . . . . . . . . . . . . . . . . . . . . . URC-5705
One For All PVR 6-Device . . . . . . . . . . . . . . . . URC-6131
One For All 6-Device Home Theater. . . . . . . . URC-6011
One For All 8-Device Home Theater. . . . . . . . URC-8011
One For All 8L-Device Home Theater
With Learning . . . . . . . . . . . . . . . . . . . . . . . . . . URC-8811
One For All A/V LCD 8 Device
With Learning . . . . . . . . . . . . . . . . . . . . . . . . . . URC-8910
One For All IR/RF LCD 8 Device
With Learning . . . . . . . . . . . . . . . . . . . . . . . . . . URC-9910
One For All 8 Device Home Theater Remote
Powered By Kameleon . . . . . . . . . . . . . . . . . . . URC-9960
ONE FOR ALL® is the registered trademark of
Universal Electronics Inc. Computime International
Ltd. is the Licensee of the ONE FOR ALL® brand for
USA and Canada.
Copyright 2003 by Universal Electronics Inc. No part
of this publication may be reproduced, transmitted,
transcribed, stored in any retrieval system, or translated
to any language, in any form or by any means, electronic,
mechanical, magnetic, optical, manual, or otherwise,
without the prior written permission of Universal
Electronics Inc.
The One For All® DVD Expert Universal Remote
Control is compatible for use in North America,
excluding Mexico.
34
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 35
IMPVE4P manual 1.0
4/11/03
4:34 PM
Page 36
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement