Monogram ZV36RSFSS Professional Restaurant-Style Wall Mount Canopy Range Hood Spec sheet

Add to my manuals
4 Pages

advertisement

Monogram ZV36RSFSS Professional Restaurant-Style Wall Mount Canopy Range Hood Spec sheet | Manualzz

ZV36RSFSS – GE Monogram 36" Stainless Steel Professional Hood

Dimensions and Specifications (in inches)

12" 35-15/16"

Each hood is shipped with a stainless steel backguard and a warming shelf. Hoods may be installed with the shelf or backguard alone, or with both as shown.

Warming

Shelf 22-1/2"

Backguard

35-15/16"

25"

Installation Clearances

These vent hoods are designed to be installed onto a wall or beneath a soffit or cabinet.

Installation with Warming Shelf

• Hoods must be installed 32" Min., 38" Max. over any type cooking surface when warming shelf is used.

Installation without Warming Shelf

• Install these hoods 30" Min. to 36" Max. above the cooking surface when installed over any professional style cooktop or range.

• These hoods may be installed 24" min. above a gas or electric drop-in style cooktop.

Soffit Installation

SOFFIT SOFFIT

Note: Clearances may vary due to type of cooking product and local codes. Check with local inspectors to be sure standard is applicable.

Wall Mount Installation

SOFFIT SOFFIT

30" Min.

36" Max.

32" Min.

38" Max.

30" Min.

36" Max.

32" Min.

38" Max.

Install these hoods 30" Min. to

36" Max. over a professional style cooktop or range.

Allow 32" Min. and 38" Max.

clearance above any cooking surface when installed with shelf.

In this installation the ductwork running from the top of the hood will be concealed in the soffit or upper cabinetry.

Specification Created 10/02

Install these hoods 30" Min. to

36" Max. over a professional style cooktop or range.

Allow 32" Min. and 38" Max. clearance above any cooking surface when installed with shelf.

For this installation, a decorative duct cover is available to conceal the ductwork running from the top of the hood. Use of the duct cover requires special consideration to the installation height above the countertop.

R

Listed by

Underwriters

Laboratories

For answers to your Monogram, ® GE Profile ™

GE appliance questions, visit our website at

GEAppliances.com or call

GE Answer Center ® service, 800.626.2000.

or

ZV36RSFSS – GE Monogram 36" Stainless Steel Professional Hood

Advanced Planning

Ductwork Planning

• These vent hoods are equipped for 10" round ductwork. In most instances they may be transitioned to 8" round.

• This hood may be vented vertically through upper cabinets, soffit or ceiling.

A duct transition piece is supplied for vertical exhaust. Use locally supplied elbows to vent horizontally through the rear wall.

• Determine the exact location of the vent hood.

• Plan the route for venting exhaust to the outdoors.

• Use the shortest and straightest duct route possible. For satisfactory performance, duct run should not exceed 150 ft. equivalent length for any duct configurations.

• Refer to “Duct Fittings” chart to compute the maximum permissible length for duct runs to the outdoors.

• Use metal ductwork only.

• Install a wall cap or roof cap with damper at the exterior opening. Order the wall or roof cap and any transition needed in advance.

Wall Framing for Adequate Support

• These vent hoods are heavy. Adequate structural support must be provided.

Hoods must be secured to vertical studs in the wall.

• It is strongly recommended that the vent hood with duct cover be on site before final framing and wall finishing. This will also help to accurately locate the ductwork and electrical service.

Decorative Duct Covers:

Decorative duct covers, 6" and 12" high, are available to fit all models. The duct cover conceals the ductwork running from the top of the hood to the ceiling or soffit. Stack one or more duct covers over the top of the hood to reach your ceiling height.

POWER SUPPLY

IMPORTANT – (Please read carefully)

WARNING:

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED.

Remove house fuse or open circuit breaker before beginning installation.

Do not use an extension cord or adapter plug with this appliance. Follow national electrical codes or prevailing local codes and ordinances .

Electric supply

These vent hoods must be supplied with 120V, 60Hz, and connected to an individual, properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or time delay fuse.

• Wiring must be 2 wire with ground.

• If the electrical supply does not meet the above requirements, call a licensed electrician before proceeding.

• Route house wiring as close to the installation location as possible on the back wall or ceiling.

• Connect the wiring to the house wiring in accordance with local codes.

Grounding instructions

The grounding conductor must be connected to a ground metal, permanent wiring system, or an equipment-grounded terminal or lead on the hood.

WARNING:

The improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.

Optional Duct Cover Accessories

6" Duct Cover

12" Duct Cover

Decorative duct covers are available in 6" and 12" heights. Duct covers may be stacked, in various combinations, to conceal the ductwork running from the top of the hood to the ceiling.

• Before you begin, you should determine the installation height of the hood and order the correct size duct cover. The duct covers should be ordered at the same time as the vent hood and be on site before installation. Order the duct cover corresponding to your model.

Specification Created 10/02

6" Duct Covers

Hood Model

ZV48R

ZV36R

ZV30R

6" Duct Cover Dimensions

ZX48DC6 6"H x 19-11/16"W x 11-7/8"D

ZX36DC6

ZX36DC6

6"H x 15-3/4"W x 11-7/8"D

6"H x 15-3/4"W x 11-7/8"D

12" Duct Covers

Hood Model

ZV48R

ZV36R

ZV30R

12" Duct Cover Dimensions

ZX48DC12 12"H x 19-11/16"W x 11-7/8"D

ZX36DC12

ZX36DC12

12"H x 15-3/4"W x 11-7/8"D

12"H x 15-3/4"W x 11-7/8"D

R

Listed by

Underwriters

Laboratories

For answers to your Monogram, ® GE Profile ™

GE appliance questions, visit our website at

GEAppliances.com or call

GE Answer Center ® service, 800.626.2000.

or

ZV36RSFSS – GE Monogram 36" Stainless Steel Professional Hood

Using Duct Cover Accessories

To avoid unsightly gaps, plan the hood installation height for duct covers use. Use the following formula to calculate the need for one of more duct covers and to ensure a trouble free installation.

Ceiling Height

We recommend that the vent hood and decorative duct cover (if used) be on site before final framing and wall finishing. This will help to accurately locate studs, ductwork and electrical service.

• Read these examples carefully to determine the need for one or more

6" or 12" duct covers.

B

10" Hood

Height

A = Countertop to ceiling height.

B = Gap at the top of the hood to the ceiling.

C = Hood installation height – Plus 10" hood height.

A

C

NOTE: Dia. C should be between 40" and 46" (for a 30" to 36" installation height). Raise or lower the hood installation height to allow use of one or more 6" and 12" duct covers.

A - B = C

INSTALLATION EXAMPLES

24"

12"

42"

38"

32"

32"

8 ft. ceilings: When the hood is installed 32" above the cooking surface and there is no soffit or upper cabinetry, order one 12" and one 6" duct cover accessory.

9 ft. ceilings: When the hood is installed 38" above the cooking surface, order two 12" duct cover accessories.

10 ft. ceilings: When the hood is installed 36" above the cooking surface, order three 12" and one 6" duct cover accessories.

Specification Created 10/02

R

Listed by

Underwriters

Laboratories

For answers to your Monogram, ® GE Profile ™

GE appliance questions, visit our website at or

GEAppliances.com or call

GE Answer Center ® service, 800.626.2000.

ZV36RSFSS – GE Monogram 36" Stainless Steel Professional Hood

Features and Benefits

• 640 CFM Vertical Exhaust

• Variable Speed Fan Control

• 2 Halogen Lamps with 4 Lighting Levels

• Infrared Warming Lamp

• Utensil Rod

• Removable Grease Trays

• Removable Stainless Steel Pattern Filters

• Model ZV36RSFSS – Stainless steel

Specification Created 10/02

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement