3-196-472-12(1) LCD Digital Color TV Operating Instructions KDL-26S3000 KDL-32S3000 KDL-40S3000 KDL-46S3000 © 2007 Sony Corporation Owner’s Record The model and serial numbers are located at the rear of the TV. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this TV. Model Name Serial No. WARNING To reduce the risk of fire or electric shock, do not expose this TV to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION RISQUE DE CHOC ELECTRIQUE, NE PAS OUVRIR PRECAUCION RIESGO DE CHOQUE ELECTRICO NO ABRIR This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the TV’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the TV. The TV shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV. CAUTION To prevent electric shock, do not use this polarized AC plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure. Declaration of Conformity Trade Name: SONY Model: KDL-26S3000/KDL-32S3000/ KDL-40S3000/KDL-46S3000 Responsible Party: Sony Electronics Inc. Address: 16530 Via Esprillo, San Diego, CA 92127 U.S.A. Telephone Number: 858-942-2230 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTIFICATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. 2 However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: s Reorient or relocate the receiving antenna. s Increase the separation between the equipment and receiver. s Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. s Consult the dealer or an experienced radio/ TV technician for help. Pursuant to FCC regulations, you are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. For Customers in Canada This Class B digital apparatus complies with Canadian ICES-003. Safety s Operate the TV only on 120 - 240 V AC. s Use the AC power cord specified by Sony and suitable for the voltage where you use it. s The plug is designed, for safety purposes, to fit into the wall outlet only one way. If you are unable to insert the plug fully into the outlet, contact your dealer. s If any liquid or solid object should fall inside the cabinet, unplug the TV immediately and have it checked by qualified service personnel before operating it further. s If you will not be using the TV for several days, disconnect the power by pulling the plug itself. Never pull on the cord. s When disconnecting AC power cord, the power cord should be easily accessible for disconnection. s For details concerning safety precautions, see “Important Safety Instructions” on page 4. Installing s The TV should be installed near an easily accessible power outlet. s To prevent internal heat buildup, do not block the ventilation openings. s Do not install the TV in a hot or humid place, or in a place subject to excessive dust or mechanical vibration. s Avoid operating the TV at temperatures below 41°F (5°C). s If the TV is transported directly from a cold to a warm location, or if the room temperature changes suddenly, the picture may be blurred or show poor color due to moisture condensation. In this case, please wait a few hours to let the moisture evaporate before turning on the TV. s To obtain the best picture, do not expose the screen to direct illumination or direct sunlight. It is recommended to use spot lighting directed down from the ceiling or to cover the windows that face the screen with opaque drapery. It is desirable to install the TV in a room where the floor and walls are not of a reflective material. CAUTION Use the following Sony TV only with the following WALL-MOUNT BRACKET. Sony TV Model No. KDL-26S3000 Sony Wall-Mount Bracket Model No. KDL-32S3000 KDL-40S3000 KDL-46S3000 SU-WL100 SU-WL500 - RHT-G800 Sony TV-Stand Model No. Use with other WALL-MOUNT BRACKET or TV stand may cause instability and possibly result in injury. To Customers Sufficient expertise is required for installing the specified TV. Be sure to subcontract the installation to a Sony dealer or licensed contractor and pay adequate attention to safety during the installation. Note This television includes a QAM demodulator which should allow you to receive unscrambled digital cable television programming via subscription service to a cable service provider. Availability of digital cable television programming in your area depends on the type of programming and signal provided by your cable service provider. Trademark Information Macintosh is a trademark licensed to Apple Computer, Inc., registered in the U.S.A. and other countries. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Manufactured under license from Dolby Laboratories. “Dolby” and double-D symbol are trademarks of Dolby Laboratories. Blu-ray Disc is a trademark. “BRAVIA” and , S-Force, BRAVIA Theatre Sync, and DMex are trademarks or registered marks of Sony Corporation. “XMB”, “XrossMediaBar” and “PS3” are trademarks of Sony Corporation and/or Sony Computer Entertainment Inc. Contents Important Safety Instructions ............................4 Welcome to the World of BRAVIA™ The Four Steps to Stunning HD Experience: Set, Sound, Source, and Setup ....................8 Picture Quality and Aspect Ratio.......................8 TV Home Menu: XMB™ (XrossMediaBar) .........9 Getting Started 1. Installing the TV.............................................11 Preventing the TV from Toppling Over .........11 Preparation for Wall-Mounting......................12 2. Locating Inputs and Outputs .......................13 Left side ........................................................13 Rear..............................................................14 3. Connecting the TV.........................................16 Cable System or VHF/UHF Antenna System........................................16 Cable System and VHF/UHF Antenna System........................................16 HD Cable Box/HD Satellite Box....................16 PC.................................................................18 Other Equipment ..........................................19 Using HDMI Control for BRAVIA Theatre Sync™ ...........................20 Bundling the Connecting Cables ..................20 4. Setting Up the Channel List – Initial Setup ...............................................21 Remote Control and TV Controls/Indicators......................................22 Inserting Batteries into the Remote control .......................................................22 Remote Control ............................................22 Indicators ......................................................26 Quick Setup Guide (separate volume) Provides a variety of optional equipment connection diagrams. How to Use P&P and PIP Features ..................27 To display a picture in the Sub Window .......27 To change channels in the Sub Window ......27 To exit from P&P and PIP ............................27 Using TV Features Adjust TV Settings ......................................28 Watching TV.................................................28 Access the equipment connected to your TV .........................................................28 Navigating through TV Home Menu on XMB™ ...........................................................29 TV Settings Descriptions..................................30 Product Support......................................30 Clock/Timers Settings.............................30 Picture Settings ......................................30 Sound Settings .......................................32 Screen Settings ......................................32 Video Options Settings ...........................34 Audio Options Settings ...........................34 Channel Settings ....................................35 Closed Captions (CC) Settings...............36 Parental Lock Settings............................36 External Inputs Settings..........................39 HDMI Settings ........................................39 General Settings.....................................40 Initial Setup.............................................40 CC Other Information Troubleshooting ................................................41 Specifications ....................................................44 Index ...................................................................45 Customer Support http://www.sony.com/tvsupport On-line Registration United States http://productregistration.sony.com Canada http://www.SonyStyle.ca/registration 3 Important Safety Instructions 1) 2) 3) 4) 5) 6) 7) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. USE AC power cord Observe the followings to prevent the AC power cord from being damaged. If the AC power cord is damaged, it may result in a fire or an electric shock. Stop using it and ask your dealer or Sony service center to exchange it. s Do not place the TV where the power cord is subject to wear or abuse. s Do not pinch, bend, or twist the cord excessively. The core lines may be bared and cut, causing a short-circuit, and resulting in a fire or an electric shock. s Do not convert or damage the power cord. s Do not allow anything to rest on or roll over the power cord. s Do not move the TV with the power cord plugged in. s Keep the power cord away from heat sources. s When you disconnect the AC power cord, disconnect it from the wall outlet first. s Be sure to grasp the plug when disconnecting the power cord. Do not pull the power cord. s Do not use the supplied AC power cord on any other equipment. s Use only an original Sony AC power cord, not other brands. Wall outlet The TV set with a three-wire grounding type AC power cord plug must be connected to an AC power socket outlet with a protective earthing connection. Do not use a poor fitting outlet. Insert the plug fully into the outlet. If it is loose, it may cause arcing and result in a fire. Contact your electrician to have the outlet changed. Wiring When connecting cables, be sure to unplug the AC power cord for your safety. Take care not to catch your feet on the cables. It may damage the TV set. Electric shock Do not touch the AC power cord or the TV with a wet hand. If you plug/unplug the AC power cord from the TV with a wet hand, it may cause electric shock. Lightning storms For added protection for this TV during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the TV due to lightning and power line surges. When not in use If you will not be using the TV set for several days, the TV set should be disconnected from the AC power outlet for environmental and safety reasons. The TV set is not disconnected from the AC power source when the TV set is switched off. To disconnect the TV set completely, pull the plug from the AC power outlet. Overloading This TV set is designed to operate on a 120 - 240 V AC supply only. Take care not to connect too many appliances to the same AC power outlet as this could result in a fire or an electric shock. Optional equipment 4 Do not install optional equipment too close to the TV set. Keep optional equipment at least 11 7/8 inches (30 cm) away from the TV set. If a VCR is installed in front of the TV set or beside the TV set, the picture may become distorted. Picture distortion and/or noisy sound may occur if the TV set is positioned in close proximity to any equipment emitting electromagnetic radiation. Small accessories MAGNETIC INFLUENCE Keep small accessories out of children’s reach. This TV contains a strong magnet in the speaker unit that generates a magnetic field. Keep any items susceptible to magnetic fields away from the speaker. ANTENNAS Outdoor antenna grounding SOUND If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits. If a snapping or popping sound from the TV is continuous or frequent while the TV is operating, unplug the TV and consult your dealer or service technician. It is normal for some TV’s to make occasional snapping or popping sounds, particularly when being turned on or off. WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM, EXTREME CARE SHOULD BE TAKEN TO KEEP FROM CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT WITH THEM IS ALMOST INVARIABLY FATAL. Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in USA and Section 54 of the Canadian Electrical Code in Canada provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70 CARRYING THE TV Carry the TV in the specified manner To avoid dropping the TV and causing serious injury, be sure to follow these guidelines: s Before carrying the TV, disconnect all cables. s Carrying the large size TV requires two or more people. s When you carry the TV, place your hand as illustrated and hold it securely. Do not put stress on the LCD panel. KDL-26S3000 KDL-32S3000/ KDL-40S3000/ KDL-46S3000 Antenna lead-in wire Ground clamps Antenna discharge unit (NEC Section 810-20) Electric service equipment NEC: National Electrical Code Grounding conductors (NEC Section 810-21) Ground clamps Power service grounding electrode system (NEC Art 250 Part H) s When lifting or moving the TV, hold it firmly from the bottom. Place your palm directly under the panel. BATTERIES s Do not dispose of batteries in a fire. s Do not short circuit, disassemble or overheat the batteries. s Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Disposal of used batteries To preserve our environment, dispose of used batteries according to your local laws or regulations. s When carrying, do not subject the TV to shocks or vibration, or excessive force. VENTILATION CLEANING Cleaning the AC power plug Unplug the AC power plug and clean it regularly. If the plug is covered with dust and it picks up moisture, its insulation may deteriorate and result in a fire. Cleaning the screen surface/ cabinet of the TV set Unplug the AC power cord when cleaning this TV. If not, it may result in electric shock. Clean the cabinet of the TV with a dry soft cloth. To remove dust from the screen, wipe it gently with a soft cloth. Stubborn stains may be removed with a cloth slightly dampened with a solution of mild soap and warm water. Never use strong solvents such as thinner or benzine for cleaning. If using a chemically pretreated cloth, please follow the instruction provided on the package. The ventilation holes can accumulate dust over time. To ensure proper ventilation, we recommend removing the dust periodically (once a month) using a vacuum cleaner. The slots and openings in the TV are provided for necessary ventilation. To ensure reliable operation of the TV and to protect it from overheating, these slots and openings must never be blocked or covered. Unless proper ventilation is provided, the TV may gather dust and get dirty. For proper ventilation, observe the following: s Do not install the TV face up, down or sideways. s Do not install the TV turned over or upside down. (Continued) 5 MOISTURE s Never cover the slots and openings with a cloth or other materials. Moisture and flammable objects s The TV must not be exposed to dripping or splashing. Do not place objects filled with liquids, such as vases, on the TV. s Do not use power-line operated TV sets near water — for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. It may result in a fire or an electric shock. s Never block the slots and openings by placing the TV on a bed, sofa, rug or other similar surface. s Do not let this TV get wet. Never spill liquid of any kind on the TV. If any liquid or solid object does fall through, do not operate the TV. It may result in electric shock or damage to the TV. Have it checked immediately by qualified personnel. s To prevent fire, keep flammable objects or open flame (e.g. candles) away from the TV. s Never place the TV in a confined space, such as a bookcase or built-in cabinet, unless proper ventilation is provided. Leave some space around the TV set as shown below. Otherwise, air-circulation may be inadequate and cause overheating, which may cause a fire or damage to the TV set. Installed on the wall 11 inches (30 cm) 4 inches (10 cm) 4 inches (10 cm) Leave at least this much space around the set. 4 inches (10 cm) Installed with stand 11 7 /8 inches (30 cm) 2 3 /8 inches 4 inches (10 cm) 4 inches (10 cm) INSTALLATION Wall mount installation requires the use of a Wall-Mount Bracket. When installing or removing the TV, using a Wall-Mount Bracket, be sure to use qualified contractors. If not properly secured during installation or removal from the Wall-Mount Bracket, the TV may fall and cause serious injury. 7/ 8 (6 cm) Optional wall mount Observe the following when installing the TV using a wall-mount bracket. s Be sure to follow the operating instructions supplied with the wall-mount bracket when installing the TV. s Be sure to attach the brackets supplied with the wall-mount bracket. s Do not hang the TV from the ceiling. It may fall and cause serious injury. Placement The TV should be installed near an easily accessible AC power outlet. Leave at least this space around the set. Never install the TV set as follows: Air circulation is blocked. Air circulation is blocked. Wall Objects and ventilation holes Never push objects of any kind into the TV through the cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or an electric shock. Do not place any objects on the TV. 6 Observe the following in placing the TV. Otherwise the TV may fall from the stand or wall mount, causing damage or serious injury. s Place the TV on a stable, level surface. s Do not hang anything on the TV. Do not allow children to climb on the TV. Wall Do not install the TV in places subject to extreme temperatures, such as in direct sunlight, near a radiator, or near a heating vent. If the TV is exposed to extreme temperature, the TV may overheat and cause deformation of the enclosure or cause the TV to malfunction. Do not install the TV in a place exposed to direct air conditioning. If the TV is installed in such a location, moisture may condense inside and may cause a malfunction. s Never place the TV in hot, oily, humid or excessively dusty places. s Do not install the TV where insects may enter. s Do not install the TV where it may be exposed to mechanical vibration. s Do not install the TV in a location where it may protrude, such as on or behind a pillar, or where you might bump your head on it. Otherwise, it may result in injury. Preventing the TV from toppling over Take measures to prevent the TV from toppling over and causing injury. To prevent the TV from toppling over, secure the TV to a wall or stand. Placement for viewing It is recommended to watch the TV at a distance of 3 - 7 times that of the screen height, and in moderate brightness. Watching the TV for too long or in a dark room may cause eye fatigue. To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible, use spot lighting directed down from the ceiling. Outdoor use Do not install this TV outdoors. If the TV is exposed to rain, it may result in a fire or an electric shock. Do not expose the TV to direct sunlight, it may heat up and become damaged. Vehicle, ships and other vessels Do not install this TV in a vehicle. Bumping of the vehicle may cause the TV to fall down and cause injury. Do not install this TV in a ship or vessel. If the TV is exposed to seawater, it may cause a fire or damage the TV. Medical institutions Do not place this TV in a place where medical equipment is in use. It may cause a malfunction of medical equipment. s The screen and cabinet get warm when the TV is in use. This is not a malfunction. s Avoid spraying insect repellent with volatile material on the screen. s Avoid prolonged contact with rubber or plastic material. Broken pieces Do not throw anything at the TV. The screen glass may break by the impact and cause serious injury. If the surface of the TV cracks, do not touch it until you have unplugged the AC power cord. Otherwise electric shock may result. Handling of broken glass and liquid crystal leakage If the LCD panel gets damaged, crystalline liquid leakage may occur, or scattered broken glass may result. Do not touch broken glass or crystalline liquid which is toxic, with bare hands as cuts, poisoning or skin irritation may occur. Also, do not let glass fragments or leaked crystalline liquid get into your eyes or mouth. Should either contact your eyes or mouth, rinse the contacted area thoroughly with water and consult your doctor. SERVICING Do not attempt to service the TV yourself since opening the cabinet may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Replacement parts Attachments Do not use attachments not recommended by the manufacturer, as they may cause hazards. When replacement parts are required, be sure the service technician certifies in writing that he/she has used replacement parts specified by the manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in a fire, an electric shock or other hazards. Safety check VOLUME ADJUSTMENT s Adjust the volume so as not to trouble your neighbors. Sound carries very easily at night. Therefore, closing the windows or using headphones is suggested. s When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result. LCD SCREEN s Although the LCD screen is made with high-precision technology and has effective pixels of 99.99% or more, black dots or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD panel and is not a malfunction. s The LCD screen is made with high-precision technology and to achieve a high level of performance and picture quality, this TV’s backlight setting is set to maximize the brightness of the TV. However, uneven brightness may be observed when the LCD TV is viewed in a dark ambient without an input source or a blank screen. This condition is normal and not a malfunction of the TV. Changing the Picture mode, Backlight setting, enabling the Light Sensor, or turning on the Power management will improve this condition. s Do not expose the LCD screen surface to direct sunlight. Doing so may damage the LCD panel. s Do not push or scratch the LCD screen, or place objects on top of the TV. The image may be uneven or the LCD panel may be damaged. s If the TV is used in a cold place, a smear may occur in the picture or the picture may become dark. This does not indicate a failure. These phenomena improve as the temperature rises. s Ghosting may occur when still pictures are displayed continuously. It should disappear after a few moments. Upon completion of any service or repairs to the TV, ask the service technician to perform routine safety checks (as specified by the manufacturer) to determine that the TV is in safe operating condition, and to so certify. Ask a qualified service technician to dispose of the TV. For Customers in the United States Lamp in this product contains mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance (www.eiae.org). 7 Welcome to the World of BRAVIA™ Thank you for purchasing this Sony BRAVIA™ high-definition television. The quality of the image you see on your BRAVIA TV is only as good as the quality of the signal it receives. To experience the stunning detail of your new BRAVIA TV, you need access to HD programming. Your BRAVIA TV can receive and display HD programming from: • • • • Over-the-air broadcasting via HD-quality antenna HD cable subscription HD satellite subscription Blu-ray Disc™ player or other external equipment Contact your cable or satellite provider for information on upgrading to HD programming. To learn more about HDTV, visit: http://www.sony.com/HDTV The Four Steps to Stunning HD Experience: Set, Sound, Source, and Setup Along with your BRAVIA TV set, a complete HD system requires an HD sound system, a source of HD programming and proper setup connections. This manual explains basic setup connections (see page 16). The Quick Setup Guide, enclosed separately, illustrates how to connect other optional equipment. Picture Quality and Aspect Ratio You can enjoy crisp, clear images, smooth movement and high-impact visuals from 1080 HD signals. When you compare a high-definition signal to a standard analog signal, you will notice a big difference. The 1080 HD signals provide more than twice the vertical resolution of the standard TV signal. High-definition and standard-definition signals are transmitted with different aspect ratios (the width-to-height ratio of the image). HDTV uses a wider screen than conventional standarddefinition TV. 16:9 (high-definition) source Most HDTV signals use a wide screen aspect ratio of 16:9. The 16:9 fills your BRAVIA screen, maintaining a crisp, clear, vivid picture. 4:3 (standard-definition) source Most standard-definition signals use a boxy 4:3 aspect ratio. When a 4:3 image is displayed on an HDTV, you will see black bars on the sides. The picture quality may not be as sharp as with HD sources. ~ • You can use the Wide Mode function of the TV to adjust the 4:3 image to fit the entire screen (see pages 24, 32 and 34). 8 TV Home Menu: XMB™ (XrossMediaBar) The XMB™ is a menu of BRAVIA features and input sources displayed on the TV screen. The XMB™ is an easy way to select programming and adjust settings on your BRAVIA TV. Press the HOME button on your remote control to access the XMB™. Product Support Clock/Timers Media Category Bar Settings Sound HOME Screen Video Options TV Category Object Bar From the horizontal Media Category Bar you can control: • Settings: timer, picture, sound, screen and other options (see page 30 for customization options). • TV Channels: available channels are displayed on the vertical Category Object Bar. • External Inputs: cable, satellite, VCR, DVD players or other inputs can also be selected from the Category Object Bar for the External Inputs. ~ • This manual is for the 26, 32 class, 40 and 46 inch BRAVIA KDL-S Series models with screen size measured diagonally. The 32 class has a 31.5 inch viewable image size (measured diagonally). 9 Getting Started 1. Installing the TV Preventing the TV from Toppling Over Getting Started Table-Top Stand TV stand 2 3 1 1 Screw the support belt (supplied) to the TV stand with a wood screw (supplied). 2 Attach the support belt to the Table-Top Stand with the securing screw (supplied) using a coin, etc. 3 Adjust the length by pulling the support belt toward you while holding the Table-Top Stand. ~ • Be sure to take measures to prevent the TV from toppling over and causing injury. • The supplied wood screw may not be used depending on the type of TV stand. In this case, or when the securing strength is not enough, use commercial screws 1/8 to 3/16 inch (3 to 4 mm) diameter to fit to the TV stand. Consult your dealer about the types of screw(s). 11 Preparation for Wall-Mounting This TV can be installed on a wall by using a WallMount Bracket (sold separately). Before mounting the TV on a wall, the Table-Top Stand must be removed from the TV. ~ • Do not remove the Table-Top Stand for any reason other than to wall-mount the TV. Follow the simple steps below to remove the Table-Top Stand: 1 Disconnect all the cables from the TV. 2 Gently lay the TV, face down, onto a level and ~ • Be sure to store the removed screws and Table-Top Stand in a safe place until you are ready to reattach the Table-Top Stand. Keep the screws away from small children. • For bracket installation, refer to the instruction guide provided by the Wall-Mount Bracket model for your TV. Sufficient expertise is required in installing this TV, especially to determine the strength of the wall for withstanding the TV’s weight. • For product protection and safety reasons, Sony strongly recommends that you use the Wall-Mount Bracket model designed for your TV and the wallmounting of your TV should be performed by a Sony dealer or licensed contractor. stable surface covered with a thick and soft cloth. Make sure the Table-Top Stand is hanging over the edge. 3 Remove the screws as shown in the illustration for your model and pull the TableTop Stand out. 4 Do not remove any other screws from the TV. Models: KDL-26S3000/KDL-32S3000 Models: KDL-40S3000/KDL-46S3000 Remove 3 designated screws only. Remove 4 designated screws only. Level surface covered with a soft cloth 12 Table-Top Stand Level surface covered with a soft cloth Table-Top Stand 2. Locating Inputs and Outputs Left side 2 2 VIDEO IN R-AUDIO-L (MONO) VIDEO Getting Started S VIDEO 1 3 Item Description 1 Headphone jack Connects to your headphones. If your headphones do not match the jack, use a suitable plug adapter (not supplied). ~ • While headphones are connected, the TV speakers are muted. 2 VIDEO IN 2 S VIDEO Connects to the S VIDEO output jack on your camcorder or other video equipment that has S VIDEO. The S VIDEO provides better picture quality than composite video (3). (See Auto S Video on page 39.) 3 VIDEO IN 2 R-AUDIO-L (MONO)/VIDEO Connects to the composite video and audio output jacks on your camcorder or other video equipment such as a VCR or video game equipment. ~ • If you have mono equipment, connect its audio output jack to the TV’s L (MONO) audio input jack. 13 Rear 1 1 S VIDEO RGB Y DIGITAL OUT (OPTICAL) PB 2 VIDEO 2 L L R AUDIO L AUDIO 8 PR (MONO) 7 AUDIO AUDIO R R 2 1 1 IN PC IN 34 3 COMPONENT IN (1080p/1080i/720p/480p/480i) VIDEO IN 5 6 DMex/ SERVICE q; VHF/UHF/ CABLE qa 9 14 (VAR/FIX) AUDIO OUT Item Description 1 HDMI IN 1 HDMI HDMI (High-Definition Multimedia Interface) provides an uncompressed, all-digital audio/video interface between this TV and any HDMI-equipped audio/video equipment, such as a set-top box, DVD player, Blu-ray Disc player, A/V receiver as well as PC. HDMI supports enhanced, or high-definition video, plus digital audio. 2 HDMI IN 2 HDMI/ R-AUDIO-L If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the HDMI IN 2 (with DVI-to-HDMI cable or adapter) jack, and connect the audio jack to the AUDIO IN (L/R) jacks of HDMI IN 2. Getting Started DVI-to-HDMI cable Audio cable DVI-to-HDMI adapter ~ • HDMI connection is necessary to view 480i, 480p, 720p, 1080i and 1080p formats. Note that this TV displays all video input signals in a resolution of 1,366 dots × 768 lines. • Be sure to use only an HDMI cable that bears the HDMI logo. 3 PC IN (RGB/AUDIO) Connects to a personal computer’s video output connector using HD15-HD15 cable (analog RGB). Can also be connected to other analog RGB equipment. See “PC Input Signal Reference Chart” on page 18 for the signals that can be displayed. ~ • For some Apple Macintosh computers, it may be necessary to use an adapter (not supplied). If this is the case, connect the adapter to the computer before connecting the HD15-HD15 cable. • If the picture is noisy, flickering or not clear, adjust Phase and Pitch of Screen settings on page 33. 4 VIDEO IN 1 S VIDEO Connects to the S VIDEO output jack of your VCR or other video equipment that has S VIDEO. S VIDEO provides better picture quality than composite video (5). (See Auto S Video on page 39.) 5 VIDEO IN 1/3 VIDEO/ L(MONO)AUDIO-R Connects to the composite video and audio output jacks on your A/V equipment such as a VCR or other video equipment. A third composite video and audio (VIDEO 2 IN) is located on the left side of the TV. 6 COMPONENT IN 1/2 (1080p/1080i/ 720p/480p/480i)/ L-AUDIO-R Connects to your TV’s component video (YPBPR) and audio (L/R) jacks. Component video provides better picture quality than the S VIDEO (4) or the composite video (5) connections. ~ • Component video (YPBPR) connection is necessary to view 480i, 480p, 720p, 1080i and 1080p formats. Note that this TV displays all video input signals in a resolution of 1,366 dots × 768 lines. 7 AUDIO OUT (VAR/FIX) Connects to the left and right audio input jacks of your analog audio equipment. You can use these outputs to listen to your TV’s audio through your stereo system. 8 DIGITAL OUT (OPTICAL) Connects to the optical audio input of your digital audio equipment that is PCM/Dolby Digital compatible. 9 AC IN Connects the supplied AC power cord. x/ 0 DMe SERVICE This USB port is for service only unless you are connecting the optional BRAVIA external module (DMex). qa VHF/UHF/CABLE RF input that connects to your Cable or VHF/UHF antenna. 15 3. Connecting the TV HD Cable Box/HD Satellite Box Cable System or VHF/UHF Antenna System You can enjoy high-definition and standarddefinition digital programming (if available in your area) along with standard-definition analog programming. ~ • This TV is capable of receiving unscrambled digital programming for both cable (QAM and 8VSB) and external VHF/UHF antenna (ATSC). • It is strongly recommended that you connect the antenna/cable input using a 75-ohm coaxial cable to receive optimum picture quality. A 300-ohm twin lead cable can be easily affected by radio frequency interference, resulting in signal degradation. You can also enjoy high-definition programming by subscribing to a high-definition cable service or a high-definition satellite service. For the best possible picture, make sure you connect this equipment to your TV via the HDMI or component video (with audio) input on the back of your TV. Shown with HDMI Connection Rear of TV 1 S VIDEO RGB Y 2 VIDEO PR L R AUDIO L AUDIO L (MONO) AUDIO AUDIO R R Cable or VHF/UHF (or VHF only) 1 1 IN 75-ohm coaxial cable Rear of TV DIGITAL OUT (OPTICAL) PB PC IN 3 VIDEO IN 2 COMPONENT IN (1080p/1080i/720p/480p/480i) HDMI cable VHF/UHF/CABLE input Cable System and VHF/UHF Antenna System Use an optional A-B RF switch (not supplied) to switch between the cable and over-the-air antenna programming, as indicated below. A-B RF switch Cable A Antenna B Rear of TV VHF/UHF/CABLE input ~ • Be sure to set the Cable setting to On or Off in the Channel settings for the type of input signal you choose (see page 35). 16 CATV/Satellite antenna cable HD cable box/ HD satellite box (VAR/FIX) AUDIO OUT Shown with DVI Connection CATV/Satellite antenna cable Rear of TV DVI-to-HDMI cable 1 S VIDEO RGB Y HD cable box/ HD satellite box DIGITAL OUT (OPTICAL) PB 2 VIDEO PR L AUDIO AUDIO R R 2 1 1 3 PC IN IN Getting Started L (MONO) AUDIO R AUDIO L COMPONENT IN (1080p/1080i/720p/480p/480i) VIDEO IN (VAR/FIX) AUDIO OUT AUDIO-R (red) AUDIO-L (white) Audio cable ~ • If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the HDMI IN 2 (with DVI-to-HDMI cable or adapter) jack and connect the audio jack to the AUDIO IN (L/R) jacks of HDMI IN 2. For details, see page 15. Shown with Component Connection CATV/Satellite antenna cable Rear of TV 1 S VIDEO RGB Y DIGITAL OUT (OPTICAL) PB HD cable box/ HD satellite box 2 VIDEO PR L R AUDIO L AUDIO L (MONO) AUDIO AUDIO R R 2 1 1 IN PC IN 3 VIDEO IN COMPONENT IN (1080p/1080i/720p/480p/480i) (VAR/FIX) AUDIO OUT AUDIO-R (red) AUDIO-L (white) PR (red) PB (blue) Component video cable Y (green) Audio cable 17 PC Use the TV as a monitor for your PC. Shown below with the HD15 to HD15 connection. This TV can also be connected to a PC with DVI or HDMI output. (Refer to the separate Quick Setup Guide.) Rear of TV 1 S VIDEO RGB Y DIGITAL OUT (OPTICAL) PB 2 VIDEO PR L R AUDIO L AUDIO L (MONO) AUDIO AUDIO R R 1 1 IN PC IN 3 VIDEO IN 2 COMPONENT IN (1080p/1080i/720p/480p/480i) (VAR/FIX) AUDIO OUT HD15-HD15 cable (analog RGB) Audio cable (stereo mini plugs) ~ • Connect the PC IN jack to the PC using the HD15HD15 cable with ferrite core (analog RGB) and audio cable (page 15). • If the PC is connected to the TV and no signal has been input from the PC for more than 30 seconds, the TV enters the standby mode automatically (page 40). PC Input Signal Reference Chart After connecting the PC to the TV, set the output signal from the PC according to the chart below. Resolution Signals VGA Horizontal frequency (kHz) Vertical frequency (Hz) Standard Horizontal (Pixel) × Vertical (Line) 640 × 480 31.5 60 VGA 640 × 480 37.5 75 VESA 720 × 400 31.5 70 VGA-T SVGA 800 × 600 37.9 60 VESA Guidelines 800 × 600 46.9 75 VESA XGA 1024 × 768 48.4 60 VESA Guidelines 1024 × 768 56.5 70 VESA 1024 × 768 60.0 75 VESA 1280 × 768 47.4 60 VESA 1280 × 768 47.8 60 VESA 1360 × 768 47.7 60 VESA WXGA ~ • This TV’s PC input does not support Sync on Green or Composite Sync. • This TV’s PC VGA input does not support interlaced signals. 18 • For the best picture quality, it is recommended to use the signals (boldfaced) in the above chart with a 60 Hz vertical frequency from a personal computer. In plug and play, signals with a 60 Hz vertical frequency will be detected automatically. (PC reboot may be necessary.) Other Equipment Blu-ray Disc Player/ “PS3” Digital satellite receiver DVD player Digital cable box Audio system Personal computer VIDEO R-AUDIO-L (MONO) VIDEO 2 S VIDEO RGB Y DIGITAL OUT (OPTICAL) PB DMex/ SERVICE 2 VIDEO PR L R AUDIO L AUDIO (MONO) L AUDIO AUDIO R R 1 PC IN 3 VIDEO IN (VAR/FIX) 2 1 IN S VIDEO Getting Started Rear of TV 1 COMPONENT IN (1080p/1080i/720p/480p/480i) AUDIO OUT VHF/UHF/ CABLE VHF/UHF/CABLE VCR Game system Digital recorder Analog Digital audio audio equipment equipment (A/V Receiver/Home Theater) Headphones Camcorder ~ • Refer to the Quick Setup Guide (supplied) when connecting other equipment to your TV. 19 Using HDMI Control for BRAVIA Theatre Sync™ This TV is equipped with BRAVIA Theatre Sync. The HDMI Control function enables BRAVIA Theatre Sync to allow communication between Sony TV's and Sony equipment. Only Sony equipment with HDMI Control capability is supported. Bundling the Connecting Cables You can bundle the connecting cables as illustrated below. To connect HDMI Control equipment Use an HDMI cable that bears the HDMI logo for connection. See pages 16 to 19 or see the HDMI connection shown in the Quick Setup Guide provided with the TV documentation. Setting the HDMI Control In order for the HDMI Control function to operate, the TV and other Sony HDMI Control equipment must be setup. See page 39 on how to turn the HDMI Control On. For other equipment, refer to the operating instruction for that equipment. 1 HDMI Control available with your TV Once the supported equipment is connected, the following operations are available: • Turn off the equipment automatically when you turn off the TV. • When the connected equipment is turned on by One-Touch-Play, the TV will automatically turn on and select the respective HDMI input. • Automatically turn on equipment listed under the External Inputs on the XMB™ (XrossMediaBar) when selected, see pages 9 and 28. When a Sony A/V receiver with BRAVIA Theatre Sync is connected, the following additional operations are possible: • Turning on the A/V receiver when the TV is turned on. • Automatically switching to the audio output of the A/V receiver's attached speakers. • Adjusting the volume and muting of the A/V receiver with the TV's remote control. ~ • The A/V receiver cannot be selected from the XMB™. 20 2 ~ • Do not bundle the AC power cord with other connecting cables. 4. Setting Up the Channel List – Initial Setup The Initial Setup screen appears when you turn on the TV for the first time. Initial Setup Step 1 of 5 ~ • If you accidentally turn off the TV during the Initial Setup process, the Initial Setup will restart from the beginning when the TV is turned back on. • The Auto Program may be canceled while the channels are being scanned. Press RETURN first then press either B/b on the remote control, highlight “Yes” to cancel or “No” to resume Auto Program. Please select a language. Language settings will apply to on screen display as well as default audio for digital to continue. English Español Français After you finish connecting the TV, you can run Initial Setup to create a list of available analog and digital channels if you have connected an antenna or cable directly to the TV’s VHF/UHF/ CABLE input. You will be prompted to select the language of your choice to be used for all the on-screen settings. Use the remote control to navigate through the Initial Setup: V/v button: s To Run Initial Setup Again or Auto Program at a Later Time Select the Initial Setup feature from the XMB™ (XrossMediaBar) or refer to the Initial Setup described on page 40. To run Auto Program, see page 35. s To Add Digital Channels Use the Add Digital Channels feature as described on page 35. (Useful for antenna installations.) s To Display the Picture in Your Preferred Aspect Ratio Select the proper Wide Mode as described on pages 24 and 32. You may want to set up convenient features such as Favorites (see page 23), Show/Hide Channels (page 35), Edit Channel Labels (page 35) when Auto Program is completed. Allows you to highlight options where applicable. button: HOME Allows you to select the highlighted option and advance to the next screen. B button: Allows you to move back to the previous screen. b button: Allows you to move to the next screen. Follow the help text provided on the screen to run Auto Program with the connected signal source or select Skip to skip the Auto Program if you are receiving channels from a cable box or satellite receiver and the VHF/UHF/CABLE input is not connected. The Auto Program will scan for available channels. When the Auto Program is completed, the TV will display how many analog and digital channels are found. 21 Getting Started channels. Highlight a choice and press Remote Control and TV Controls/Indicators Inserting Batteries into the Remote control Insert two size AA batteries (supplied) by matching e and E on the batteries to the diagram inside the battery compartment of the remote control. Push to open Remote Control Buttons located at the top of the TV will operate the same as these buttons on the remote control. 1 2 HOM E ~ • The 5 button and CH + have a tactile dot. Use them as a reference when operating the TV. • This remote control cannot be programmed to use with other equipment. Button Description 1 DISPLAY Press once to display the information pertaining to the channel and/or program when available. The OSD (On Screen Display) will time out in a few seconds or press again to immediately turn off the display. You can also set the display to show minimal information. See Info Banner on page 40. Press repeatedly until the TV displays the time in minutes (Off, 15min, 30min, 45min, 60min, 90min or 120min) that you want the TV to remain on before shutting off. To cancel Sleep Timer, press SLEEP repeatedly until Off appears. 2 SLEEP 22 Button Description 3 FREEZE Press once to display a frozen image with the current program in a window. Press again to fill the screen with the frozen image. Press 3rd time to return to the current program. Freeze Current program Frozen picture ~ 3 4 5 6 7 8 4 PICTURE 5 FAVORITES • With the Freeze feature active, some features are unavailable. • While the Freeze feature is active, pressing HOME will deactivate the Freeze and display the XMB™. Press repeatedly to cycle through the available picture modes: Vivid, Standard, Cinema, Video, Text. (Available options depend on the current mode.) The picture modes can also be accessed in the Picture settings. For details, see Picture settings on page 30. Press once to display the stored favorite channel list. You can store up to 30 channels in your Favorites list. How to Add to Favorites While tuned to the channel you want to add to the list, press OPTIONS and highlight “Add to Favorites”, then press . A confirmation message of “Channel added to Favorites” will appear for a few seconds. 9 How to Remove from Favorites While tuned to a channel that exists in the Favorites list, press OPTIONS and highlight “Remove from Favorites”, then press . A confirmation message of “Channel removed from Favorites” will appear for a few seconds. 0 ~ 6 RETURN 7 HOME Your Favorites list will be cleared each time you run Auto Program (see pages 21 and 35 for Auto Program). Press to go back to the previous screen or exit from the screen when displaying menu items and settings. Press to display the TV Home Menu/XMB™ (XrossMediaBar) to access the TV Home Menu items such as the TV Settings, TV channels and External Inputs list (see pages 9 and 28). Product Support Clock/Timers Sound Screen Video Options TV 8 DMex Press to access features in the optional BRAVIA external module (e.g. DMX-NV1). See your dealer or www.sony.com/bravia for more information. The module may not be available in your region. 9 0-9 ENT Press 0-9 to select a channel; the channel changes after two seconds. Press ENT to change channels immediately. Use with 0-9 and ENT to select digital channels. For example, to enter 2.1, press 2 , , 1 and ENT. 0 (Continued) 23 Getting Started Press the V/v/B/b to move the small window showing current program to a different location on the screen. Button Description qa VOL +/– Press to adjust the volume. qs MUTING Press to mute the sound. Press again or press VOL + to restore the sound. Press to turn on and off the TV. qd POWER qf WIDE qd Press repeatedly to step through the Wide Mode settings: Wide Zoom, Normal, Full, Zoom. The Wide Mode settings can be also accessed in the Screen settings (see page 32). Changing the Wide Screen Mode qf (For PC timing, see below) 4:3 Original source Standard-definition source 16:9 Original source High-definition source m Wide Zoom m Wide Zoom Normal Normal This mode is not available Full Full Zoom Zoom ~ qa • When the TV receives a 720p, 1080i or 1080p signal, Normal cannot be selected. Changing the Wide Screen Mode for PC timing qs Incoming PC signal Incoming PC signal 800 × 600 24 1280 × 768 m Normal Normal m Full 1 Full 1 Full 2 Full 2 Button Description qg INPUT Press to display the list of External Inputs and TV mode. Press repeatedly to toggle through the inputs. ~ qh V/v/B/b qj OPTIONS Menu Item Picture Sound P&P or PIP Audio Swap Exit P&P or Exit PIP Speakers Add to Favorites/ Remove from Favorites MTS Alternate Audio Digital Rating Screen qg qh qj qk ql qk CC ql JUMP w; CH +/– See page 34 See page 34 See page 37 See page 32 Press to turn on and off the Closed Captions (CC). To change or customize the CC Display, see page 36. Press to jump back and forth between two channels. The TV alternates between the current channel and the last channel that was selected. JUMP w; Reference Page See page 30 See page 32 See page 27 See page 27 See page 27 See page 34 See page 23 JUMP Press to scan through channels. To scan quickly through channels, press and hold down either +/–. 25 Getting Started • See page 39 on setting up the External Inputs labels, including the Skip feature. Press V/v/B/b to move the on-screen cursor. Press to select/confirm an item. Press to display a list of convenient functions and menu shortcuts. The OPTIONS menu items vary based on input and content. Indicators 1 6 PIC OFF/TIMER 2 3 STANDBY 4 POWER 5 Item Description 1 Speaker Outputs the audio signal. 2 Light Sensor Senses room light level and adjusts the screen brightness accordingly (see page 40 for details). Do not put anything near the sensor, as its function may be affected. 3 PIC OFF/ TIMER LED Lights up in green when the Picture Off feature is activated. Lights up in orange when the timer is set. When the timer is set, this LED will remain lit even if the TV is turned off. For details, see page 30. 4 STANDBY Lights up in red when your TV is in PC standby mode. If the LED LED blinks in red continuously, this may indicate the TV needs servicing (see contacting Sony information on the back cover). 26 5 POWER LED Lights up in green when the TV is turned on. 6 (IR) Infrared Receiver Receives IR signals from the remote control. How to Use P&P and PIP Features This TV comes with the P&P and PIP features which allow you to view two pictures simultaneously. P&P (picture and picture) provides two windows side by side. PIP (picture in picture) provides PC input signal and TV channels. ~ P&P Main Window Sub Window PIP Main Window (PC) Sub Window (Location of the Sub Window can be moved by pressing V/v/B/b.) To display a picture in the Sub Window 1 While watching one of the following inputs: Component, HDMI or PC; press OPTIONS to display the OPTIONS menu. Press CH +/– to change the channels or enter the channel number using the 0-9 numeric buttons. To exit from P&P and PIP 1 Press the OPTIONS. 2 Press while Exit P&P or Exit PIP Getting Started • The VHF/UHF/CABLE input must be connected to use the P&P/PIP feature. • These features are not available when the Parental Lock settings are set to block programs by ratings. If channel blocking is set, these features can still be used. • Closed Captions (CC) is not available in these features. To change channels in the Sub Window (depends on the mode your are in) is highlighted. ~ • You may also press RETURN while in this feature to exit. • Additional compatible device with television tuner required to watch two simultaneous live television programs. P&P Availability In Main Window In Sub Window Component 1 TV Channel Component 2 (VHF/UHF/ HDMI IN 1 (except PC timing) CABLE IN) HDMI IN 2 (except PC timing) PIP Availability In Main Window In Sub Window PC TV Channel HDMI IN 1 (PC timing) (VHF/UHF/ CABLE IN) HDMI IN 2 (PC timing) ~ • Compatible PC Timings can be found on page 18. ~ • The input you are watching will become the Main Window. 2 Press V/v to highlight the P&P or PIP and press to display the TV channels in the Sub Window. ~ • To swap audio in P&P mode, use the B/b button to swap the highlight between the Main Window and Sub Window. • To swap audio in PIP mode, press OPTIONS, then press V/v to highlight Audio Swap. 27 Using TV Features The HOME button allows you to access the TV Home Menu on the XMB™ (XrossMediaBar) as well as a variety of TV features. HOME cc Product Support Clock/Timers The XMB™ displays the Media Category icons (horizontally) and available features (vertically) within the highlighted icon. Settings Sound Screen The XMB™ is shown here with Settings highlighted. Video Options TV Media Category Icons Adjust TV Settings Settings Customize the TV settings with various options. Explanations of different Settings start from page 30. • The available options vary depending on the situations and conditions applied. Unavailable options are grayed out or not displayed. Watching TV TV Select a channel. • You can also select a TV channel using the number 0-9 or CH+/– buttons (see remote control section pages 23 and 25). Access the equipment connected to your TV External Inputs 28 Watch a movie, play a game, record a program or work on your PC. Assign a label using the Label Inputs feature for your convenience, see page 39. Navigating through TV Home Menu on XMB™ 1 HOME 2 Press HOME to display the XMB™. Press B/b to select a Media Category icon. Settings 3 Available channels are listed under the TV icon. Select inputs from Video1-3 Component 1-2 HDMI 1-2 PC under the External Inputs icon. Using TV Features Available TV settings and features are listed under the Settings icon. Press V/v to move within the Category Object Bar. (The Category Object Bar shown below is for the Settings.) Product Support (page 30) Clock/Timers (page 30) Picture (page 30) Sound (page 32) Screen (page 32) Video Options (page 34) Audio Options (page 34) Channel (page 35) CC Closed Captions (CC) (page 36) Parental Lock (page 36) External Inputs (page 39) HDMI Settings (page 39) General (page 40) Initial Setup (page 40) 4 Press when desired item is highlighted. 5 Press or, V/v to select the highlighted item. 6 RETURN Press RETURN or HOME to exit. HOME 29 TV Settings Descriptions Product Support Contact Sony Sony contact information is available from this screen for your convenience. Your TV’s specific information such as Model Name, Serial Number, Software Version and downloadable ratings if available from the TV are displayed here. Signal Diagnostics Press to display the diagnostics information for the current signal. Clock/Timers Settings Current Time Set the current time (day, hour, minutes, and AM/PM). The Timer feature will not be available until you set the Current Time. 1 Use the V/v/B/b button to highlight the Clock/Timers icon and press . 2 Use the V/v/B/b button to set the current time. 3 Press RETURN to display the confirmation screen. 4 Select Yes or No to save changes you made. Selecting Yes will save your settings and exit the Current Time setting screen. Timer After the Current Time is set, you can set the Timer to automatically turn the TV on and off and tune to a specific channel at a scheduled time. 1 Use the V/v/B/b button to highlight the Timer icon and press . 2 Press to select On to set the timer. 3 Use the V/v/B/b button to set the following: Day of the Week, Time, Duration, Channel, and Volume. 4 Press RETURN to display the confirmation screen. 5 Select Yes or No to save changes you made. Selecting Yes will save your settings and will light up the TIMER LED. Exit the Timer setting screen. Sleep Timer Sets the time in minutes (Off, 15min, 30min, 45min, 60min, 90min, or 120min) that you want the TV to remain on before shutting off automatically. This can also be set using the SLEEP button on the remote control (see page 22). Picture Settings Picture Mode (Except for PC timing) Vivid For enhanced picture contrast and sharpness. Standard For standard picture settings. Recommended for home entertainment. Cinema For viewing film-based content. Most suitable for viewing in a theater-like environment. Picture Mode Video (For HDMI or PC timing) Text This option is available for PC timing (HDMI or PC input) signal for viewing video. This option is available for PC timing (HDMI or PC input) signal to enhance the text shown on the screen. ~ • Picture Mode for all inputs can also be accessed by pressing PICTURE on the remote control to directly toggle the modes. 30 Reset Resets the current Picture Mode setting to the default values. Backlight Brightens or darkens the backlight. Picture Increases or decreases picture contrast. Brightness Brightens or darkens the picture. Color Increases or decreases color intensity. Hue Increases or decreases the green tones. Color Temperature White adjustment Cool Gives the white colors a bluish tint. Neutral Gives the white colors a neutral tint. Warm 1, 2 Gives the white colors a reddish tint. ~ • Picture Mode settings determines the available Color Temperature options: Picture Mode for all modes excluding PC timing Cool Neutral Warm1, 2 Vivid yes yes n/a Standard yes yes yes Cinema yes yes yes PC timing only (HDMI or PC input) Video Text yes yes yes yes yes yes Sharpness Sharpens or softens the picture. Noise Reduction Reduces the noise level of connected equipment, and the VHF/UHF/CABLE input. MPEG Noise Reduction Reduces the mosaic effect in MPEG-compressed video. Useful for DVDs and Digital TV channels. Advanced Settings Advanced Settings are available for the following conditions: Vivid Standard Cinema Advanced Settings Reset n/a yes yes PC timing (HDMI or PC input) n/a Resets all the advanced settings to the default values. Black Corrector Enhances black areas of the picture for stronger contrast. Advanced C.E. Automatically optimizes the backlight and contrast. This setting is especially effective for dark picture scenes. It will increase the (Advanced contrast distinction of the dark picture scenes. Contrast Enhancer) Gamma Adjusts the balance between the light and dark areas of the picture. Clear White Emphasizes white and light colors. Color Space Selects the range of color reproduction from Wide or Normal. Live Color When Color Space is set to Wide, this option makes colors more vivid and reproduces clear skin tones. Picture settings for PC timings (HDMI or PC input) are available with the following options (see above for details). Picture Mode Reset Backlight Picture Brightness Color Temperature ~ • Picture settings for all inputs can also be accessed by pressing OPTIONS on the remote control, then selecting Picture from the OPTIONS menu. 31 Using TV Features Color Temperature options Sound Settings Available Sound settings depend on the Speakers setting under Audio Options settings (page 34) or headphone connection. Sound Mode Dynamic Enhances treble and bass. Standard Suitable for spoken dialog. Custom Customizes the sound settings including the Sound Booster setting. ~ • Sound Mode can also be accessed by pressing OPTIONS on the remote control. Reset Resets the current Sound Mode setting to the default values. Treble Increases or decreases higher-pitched sounds. Bass Increases or decreases lower-pitched sounds. Balance Emphasizes left or right speaker balance. Surround S-FORCE Provides a virtual surround sound experience made possible using just Front Surround two front speakers. Off Sound Booster Select for normal stereo or mono reception. The Sound Booster provides a fuller sound with a greater sense of depth and width, by emphasizing the High and Low frequency sounds. Select High or Low for the amount of boost you desire while in the Custom Sound Mode. Selecting Off will bypass the emphasis. ~ • The Sound Booster is automatically in the High position for Dynamic Sound Mode and Low position for Standard Sound Mode. Steady Sound Volume Offset On Stabilizes the volume across all programs and commercials. Off Turns off Steady Sound. Adjusts the volume level of the current input (TV or video input) relative to other inputs. Screen Settings Wide Mode Wide Zoom Fills the screen with minimum distortion. Normal Displays the 4:3 picture in its original aspect ratio when the original source is 4:3. ~ • Normal is not available when you are watching 720p, 1080i or 1080p sources. Full Enlarges the picture horizontally to fill the screen when the original source is 4:3 (Standard-definition source). When the original source is 16:9 (High-definition source), select this mode to display the 16:9 picture in its original size. Zoom Select to enlarge the picture horizontally and vertically to fill the screen while maintaining the aspect ratio. ~ • Wide Mode can also be accessed by pressing the WIDE button. • See WIDE button description on page 24 for accessing the Wide Mode. 32 Auto Wide 4:3 Default Select the default screen mode to use for 4:3 sources On Automatically changes Wide Mode setting based upon content. If frequent screen changes are disturbing to you, select Off. Off Turns off the Auto Wide option. Choose a Wide Mode from the Wide Mode option. Wide Zoom Enlarges the 4:3 picture to fill the 16:9 screen, displaying as much of the original image as possible. Normal Displays the 4:3 picture in its original aspect ratio. Full Select to enlarge the 4:3 picture horizontally only, to fill the screen. Zoom Select to enlarge the picture horizontally and vertically to fill the screen while maintaining the aspect ratio. Off Select to continue using the current Wide Mode setting when the channel or input is changed. ~ Display Area Normal Displays the picture in its original size. -1/-2 Enlarges the picture to hide the edge of the picture. Screen Position Adjust the Vertical positioning by pressing the V/v buttons. Press the B/b buttons to adjust the Horizontal positioning. ~ • Screen Position option is available for standard-definition signals only. Vertical adjustment is available only when Wide Mode is set to Zoom. • Screen Position feature is useful if the TV is connected to game equipment. Vertical Size Adjusts the vertical size of the picture. (Available only in Wide Zoom and Zoom.) Press B/b and press to adjust. Screen settings for PC timings (HDMI or PC input) differ from all other input modes and are shown below. Auto Adjust Select Yes to start the auto adjust to display the PC input. Reset Resets the current screen setting to the default values. Phase Adjust after Pitch to fine tune overall sharpness. Pitch Adjust uneven sharpness on screen. ~ • For the PC input Signal Reference Chart, see page 18. H Center Allows you to move the position of the picture horizontally (left and right). To Adjust the H Center Press V/v to highlight H Center and press . Press B/b to correct the centering then press . V Center Allows you to move the position of the picture vertically (up and down). To Adjust the V Center Press V/v to highlight V Center and press . Press B/b to correct the centering then press . (Continued) 33 Using TV Features • This option is not available if Auto Wide is set to Off. • If 4:3 Default is set to anything but Off, the Wide Mode setting applies only to the current channel. When you change channels (or inputs), Wide Mode is automatically replaced with the 4:3 Default setting for 4:3 sources. To retain the current Wide Mode setting as channels and inputs are changed, set 4:3 Default to Off. Wide Mode Normal Select to display the picture in its original resolution and aspect ratio. Full 1 Select to enlarge the picture to fill the screen, while maintaining its original aspect ratio. Full 2 Select to enlarge the picture to fill the screen. ~ • Wide Mode can also be accessed by pressing the WIDE button. Video Options Settings CineMotion Select Auto to automatically detect film content and apply a reverse 3-2 pulldown process. Moving pictures will appear cleaner and more natural looking. The CineMotion feature can be set separately for each external input. Select Off to disable the detection. Audio Options Settings MTS Enjoy stereo, bilingual and mono programs Stereo For stereo reception when viewing a TV program broadcast in stereo. Auto SAP Automatically switches the TV to second audio programs when a SAP signal is received. If no SAP signal is present, the TV remains in Stereo mode. Mono For mono reception. Use to reduce noise during weak stereo broadcasts. ~ • MTS is available only for analog programs. Speakers Audio Out Easy control of volume adjustment TV Speakers Select to use the TV speakers for audio. Audio System Select this option if you wish to use an external audio system for the TV sound. By selecting this option you are disabling the TV speakers. Fixed Select to fix the audio output and allow you to adjust the volume with your audio system’s remote control. (The TV’s remote control’s VOLUME and MUTING buttons have no effect on the Audio Out.) Variable Select to control the Audio Out’s volume and muting with your TV’s remote control. ~ • Alternate Audio feature is available only for digital programs. If the program you are watching is also available in other languages from the audio tracks, and if that language is what you have selected in the Language setting, your TV will automatically switch to the matching language with the Alternate Audio feature. The Alternate Audio option may be accessed by pressing the OPTIONS button on the remote control when alternate audio stream is available from the broadcaster. 34 Channel Settings Cable On For receiving cable channels via cable TV provider. Off For using an antenna. ~ • You should run Auto Program after changing the Cable setting. Auto Program Automatically sets up the channel list on the TV for all receivable channels. Channel scanning will be based on the Cable On/Off setting. 1 Select Auto Program. 2 Select OK to start Auto Program. When Auto Program is completed, the screen will display the number of channels found. 3 Press RETURN to exit the Auto Program. • Running Auto Program will clear Favorites list. • If you run Auto Program again, previously scanned channels will be overwritten with the newly scanned channels. Add Digital Channels Select to add digital channels. Be sure to have the Cable option selected appropriately for the signal source. (Useful for antenna installations.) Show/Hide Channels Allows you to show or hide channels when you surf with the CH +/– button or in the TV channel list on the XMB™. 1 Press V/v to scroll through the channels until you highlight the channel to show or hide. 2 Press to select Shown or Hidden. To show or hide more channels, repeat steps 1-2. ~ • Hidden channels can be accessed by entering the channel number with 0-9 buttons on the remote control. Edit Channel Labels Assigns labels (such as station call letters) to channel numbers. 1 Press V/v to scroll through the channel numbers. Then press to select the channel number to assign a label. 2 Press V/v to scroll through the label characters (A-Z, 0-9, etc.). Press b to move to the next character. Repeat to add up to 7 characters to the label. Press to set it. To assign labels to more channels, repeat steps 1-2. 35 Using TV Features ~ CC Closed Captions (CC) Settings CC Display This option allows you to turn On or Off the Closed Captions (CC) feature. Analog CC Select this option for the basic analog (EIA-608) closed caption options. CC1, CC2, CC3, CC4 Displays a printed version of the dialogue or sound effects of a program. (Should be set to CC1 for most programs.) Text1, Text2, Text3, Text4 Displays network/station information presented using either half or the whole screen (if available). Digital CC Select this option for both analog (EIA-608) and digital (EIA-708) closed caption options. Select from CC1-4 and Service 1-6 (advanced digital closed caption options). Display Options Customize the Closed Captions (CC) displays with Text, Character Size, Character Style, Character Color, Character Opacity, Edge Type, Edge Color, Background Color and Background Opacity. ~ • Closed Captions (CC) can be turned on and off directly by pressing the CC button on the remote control. Parental Lock Settings The Parental Lock feature allows you to block programs according to their content and rating levels and block channels (regardless of the programs). Password is necessary in setting up blocking. To View Blocked Programs Press ENT when tuned to a blocked program, then enter the password. To reactivate the Parental Lock settings, turn off and on the TV. Password Use 0-9 button on the remote control to enter a four-digit password. The first time the password is created, you must re-enter it again to confirm the password. “Password Set” message will appear on the screen upon confirmation. Change Password You can change your password by entering the Parental Lock setting with the previously set password, highlight and select the Change Password then enter the new password. ~ • You need your password for any future access into the Parental Lock settings. If you lose your password, see “Lost password” on page 43. Country 36 Select the country name of U.S.A. or Canada for the appropriate ratings. The rating system varies between these two countries. See Custom Rating System Chart on page 38. Rating Off Turns off Parental Lock. No programs are blocked from viewing based on their ratings. Child Maximum ratings permitted are: U.S.: TV-Y, TV-G, G Canada: C, G, TV-Y Youth Maximum ratings permitted are: U.S.: TV-PG, PG Canada: C8+, PG, 8 ans+, TV-PG Young Adult Maximum ratings permitted are: U.S.: TV-14, PG-13 Canada: 14+, 13 ans+, TV-14 Custom Sets ratings manually. U.S.: See page 38 for details. Canada: See page 38 for details. ~ Digital Rating (Available only in U.S.A. where advanced ratings exist) Off Turn Digital Rating off. No programs containing digital ratings are blocked from viewing. Custom Select to customize the Parental Lock with downloadable digital ratings. Clear All Select to clear the downloaded ratings. Unrated Allow Allows programs and movies that are broadcast without a rating. (Available only when Block Blocks all programs and movies that are broadcast without a rating. Country is set to U.S.A.) Block programs or movies ~ that are broadcast without • If you block unrated TV programs, be aware that the following types of programs may a rating be blocked: programs broadcast from another country, emergency broadcasts, political programs, sports, news, public service announcements, religious programs and weather. Channel Block This option allows you to block channels regardless of program ratings. The password needs to be set up prior to blocking channels. The blocked channel can only be viewed by entering the correct password. To View a Blocked Channel Press ENT button when tuned to the blocked channel then enter the password. (Continued) 37 Using TV Features • If you are not familiar with the parental guideline rating system, you should select Child, Youth, or Young Adult to help simplify the rating selection. To set more specific ratings, select Custom. Custom Rating System Chart For Country selection of U.S.A.: Movie Rating TV Rating Block programs by their rating, content or both G All children and general audience PG Parental guidance suggested PG-13 Parental guidance for children under 13 R Restricted viewing, parental guidance is suggested for ages under 17 NC-17 and X No one 17 or under allowed Age-Based Ratings TV-Y All children TV-Y7 Directed to children age 7 and older TV-G General audience TV-PG Parental guidance suggested TV-14 Parents strongly cautioned TV-MA Mature audience only Content-Based Ratings FV Fantasy violence D Suggestive dialogue L Strong language S Sexual situations V Violence ~ • To ensure maximum blocking capability, set the Age-Based Ratings. For Country selection of Canada: English Rating French Rating U.S.A. Rating 38 C All children C8+ Children 8 years and older G General programming PG Parental guidance 14+ Viewers 14 and older 18+ Adult programming G General programming 8 ans+ Not recommended for young children 13 ans+ Not recommended for ages under 13 16 ans+ Not recommended for ages under 16 18 ans+ Programming restricted to adults See TV Rating under U.S.A. for details. External Inputs Settings Label Inputs You can label your inputs with the name of equipment you have connected. To assign your own label or Skip the input: 1 Press V/v to highlight the video input (Video 1-3, Component 1-2 and HDMI 12, PC), then press to select the desired input. 2 Press V/v to highlight the display label you want to assign, then press . ~ • You can select from the following labels for each input. Video 1-3, Component 1-2 and HDMI 1-2: –, DVD, Cable Box, Satellite, BD, VCR, Receiver, DVR, Game, Camcorder, PC, Skip. PC: –, Skip. • “–” indicates that no labels are assigned and displayed with the default labeling. Both Video 1 and Video 2 are equipped with S VIDEO. Select Auto to connect the S VIDEO cable instead of the composite video cable for auto video detection. If you are using the composite video cable, set the setting to Off. The Off setting will disable the auto detect and allows composite connection. HDMI Settings HDMI inputs of this TV will recognize and communicate with other Sony equipment equipped with HDMI Control. HDMI Control On/Off feature allows your TV to communicate with other equipment that supports HDMI Control. Device Auto Power Off Select On to have your connected HDMI Control equipment to power off automatically when the TV is turned off. Select Off to disable this function. TV Auto Power On Select On to control your TV’s power on from your connected HDMI Control equipment. Select Off to disable this function. Device List Displays a list of HDMI Control equipment connected to the TV. 39 Using TV Features Auto S Video General Settings Language Select the language of your choice from English, Español and Français to be used for displaying all the on-screen settings. Info Banner Displays the program name and the program information such as program title and program rating (if available from the broadcaster) when option is set to On. Select Off for minimal display information. Selecting Off will not completely disable the banner display. Info Banner also appears on the screen each time the channel is changed or DISPLAY button on the remote control is pressed. ~ • To see the rating information on the banner, Info Banner setting must be set to On. Power Saving Reduces the power consumption by adjusting the backlight brightness. This also enhances the black level. Select from Off, Low, High and Picture Off. Light Sensor Enables the automatic picture (screen) brightness control. The Light Sensor measures the room brightness which allows the TV to automatically adjust the backlight brightness based on the picture settings and the ambient room light conditions. ~ • Be sure not to put anything around the sensor, as its function may be affected (see page 26). • In low light the range of the backlight control is reduced when the Light Sensor is set to On. PC Power Management On Automatically enters to standby mode when there is no signal input for more than 30 seconds. The STANDBY LED on the front panel will illuminate when PC Power Management switches the TV to standby mode. Off Turns off PC Power Management. ~ • To bring the TV out of standby mode and recover TV features, press POWER on the remote control. • PC Power Management is not VESA-compliant. Initial Setup If you have missed the Initial Setup when you first connected the TV or if you want to scan all receivable channels, you can run the Initial Setup. Follow the instructions on the screen. Settings such as picture and sound adjustments will not be affected by this Initial Setup. ~ • Favorites list will be cleared each time you run the Initial Setup. 40 Other Information Troubleshooting If you have questions, service needs, or require technical assistance related to the use of your Sony TV, please visit our website or call one of the following numbers: Condition http://www.sony.com/tvsupport 1-800-222-SONY(7669) for US Support 1-877-899-SONY(7669) for Canadian Support Explanation/Solution No picture • Check the Power Saving settings (see page 40). Cannot receive any channels • Make sure the power cord is connected securely. • Turn on the power of the TV. • Check antenna/cable connections. • Make sure the Cable setting is correct for your TV signal source. TV is locked to one channel • Perform Auto Program to add receivable channels that are not present in the TV’s memory (see pages 21 and 35). Cannot receive or select channels • Perform Auto Program to add receivable channels that are not present in the TV’s memory (see pages 21 and 35). • To receive or select cable channels, make sure that Cable in the Channel settings is set to On (see page 35). To receive or select UHF channels over an antenna, make sure Cable is set to Off. The TV turns off automatically • Check if Sleep Timer is activated, or confirm the Duration setting of Timer (see page 30). • Check PC Power Management in General Settings (see page 40). No picture from some video sources • Check the connection between the optional video equipment and the TV. • Press INPUT on the remote control (see page 25). • Press HOME on the remote control. Select your desired input from the External Inputs list. Poor picture The quality of the images is not as good as what I saw at the store • Picture quality depends on the signal content. See Quick Setup Guide (supplied) to display the best possible picture for that signal. Double images or ghosts • Check antenna/cable connections. • Check the antenna location and direction. Only snow and noise appear on the screen • Check if the antenna is broken or bent. • Check if the antenna has reached the end of its serviceable life. (3-5 years in normal use, 1-2 years at the seaside.) Dotted lines or stripes • Keep the TV away from noise sources such as cars, motorcycles, or hair-dryers. • If using 300 ohm twin lead, move the excess lead away from the TV or try using 75 ohm coaxial cable instead. No color/Dark picture/Color is • Press PICTURE to select the desired Picture Mode (see page 23). not correct/The picture is too • Adjust the Picture Mode options in the Picture settings (see page 30). bright • If you set the Power Saving mode to Low or High, it will enhance the black level (see page 40). Noisy picture • Make sure that the antenna is connected using a 75-ohm coaxial cable. • Keep the antenna cable away from other connecting cords. • To avoid TV interference, make sure to use an undamaged antenna cable. (Continued) 41 Other Information No picture Condition Explanation/Solution No sound/Noisy sound Good picture, no sound • Check the volume control. • Press MUTING or VOL + so that “Muting” disappears from the screen (page 24). • Disconnect your headphones. • Set Speakers to TV Speakers in the Audio Options settings (see page 34). If it is set to Audio System, sound is not output from the TV’s speakers regardless of the TV’s volume control. Audio noise • Make sure that the antenna is connected using a 75-ohm coaxial cable. • Keep the antenna cable away from other connecting cords. • To avoid TV interference, make sure to use an undamaged antenna cable. PC Input No Picture / No Signal • Confirm the PC is correctly connected to the TV with either the PC IN (with an HD15 cable) or with the HDMI IN. • Ensure the output signal from the PC is one of the formats listed on page 18. • Turn the PC off. Confirm the PC connection and restart the PC. Plug and play will auto-detect the TV and correctly set up PC timing. • Verify PC Power Management is activated (see page 40). Poor Picture • Adjust the resolution (see page 18). • Adjust Pitch and Phase. General Wide Mode changes automatically • The current Wide Mode setting is automatically replaced with the 4:3 Default setting when you change the channel or video input, if 4:3 Default in the Screen settings is set to other than Off. If you want to lock in Wide Mode selected with WIDE on the remote control, set 4:3 Default to Off in the Screen settings (see page 32). • Check the Auto Wide option in the Screen settings (see page 33). Suddenly the picture gets smaller • The picture gets smaller during the commercials, this is due to the method the provider broadcasts their contents. When HD content channels switch to SD definition content (commercials), the picture may be small with a black border. “Black box” on screen • You have selected a text option and no text is available (see page 36). To turn off this feature, set the CC Display option to Off. If you were trying to select closed captioning, select CC1 instead of Text1-4. Black bands appear at the edges of the screen • Some wide screen programs are filmed in aspect ratios that are greater than 16:9 (this is especially common with theatrical releases). Your TV will show these programs with black bands at the top and bottom of the screen. For more details, check the documentation that came with your DVD (or contact your program provider). • Programs in 4:3 aspect ratio will have bands on left and right sides of the screen. Certain programs on DVD or • This is due to the digital compression of the source content used by certain other digital sources display a digital broadcasts and DVDs which may cause your TV’s screen to display less loss of detail, especially during detail than usual, or cause artifacts (small blocks or dots, pixelations) to appear fast-motion or dark scenes on your screen. These signal compressions are more visible and are dependent on the clarity and resolution of the television. Remote control does not operate • Check the polarity of the batteries or replace the batteries. • Point the remote control at the remote control sensor located at the front of the TV. • Fluorescent lamps can interfere with your remote control operation; try turning off the fluorescent lamps. • Keep the remote control sensor area clear from obstacles. Some digital cable channels are not being displayed • Certain cable companies have limitations on the broadcast of digital cable channels. Check with your cable company for more information. • The digital cable channel may be set to Hidden in the Show/Hide Channels setting (see page 35). 42 Condition Lost password Explanation/Solution • Select the Password settings on the Parental Lock settings, then enter the following master password: 4357. The master password clears your previous password and allows you to enter a new password (see page 36). How to reset the TV to factory • Turn on the TV. While holding down V on the remote control, press POWER settings on the TV. (The TV will turn itself off, then back on again.) Release V. WARNING: The Reset will clear all of your customized settings including the Parental Lock setting. Other Information 43 Specifications Model KDL-26S3000 KDL-32S3000 KDL-40S3000 KDL-46S3000 System Television system NTSC: American TV standard ATSC (8VSB terrestrial): ATSC compliant 8VSB QAM on cable: ANSI/SCTE 07 2000 (Does not include CableCARD functionality) Channel coverage Analog terrestrial: 2-69 / Digital terrestrial: 2-69 Analog Cable: 1-125 / Digital Cable: 1-135 Panel system LCD (Liquid Crystal Display) Panel Speaker output 10 W + 10 W Input/Output jacks Antenna 75-ohm external terminal for VHF/UHF VIDEO IN 1/2/3 S VIDEO (4-pin mini DIN)(VIDEO 1/2 only): Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative / C: 0.286 Vp-p (Burst signal), 75 ohms VIDEO: 1 Vp-p, 75 ohms unbalanced, sync negative AUDIO: 500 mVrms (100% modulation)/ Impedance: 47 kilohms COMPONENT IN 1/2 YPBPR (Component Video): Y: 1.0 Vp-p, 75 ohms unbalanced, sync negative / PB: 0.7 Vp-p, 75 ohms / PR: 0.7 Vp-p, 75 ohms / Signal format: 480i, 480p, 720p, 1080i, 1080p AUDIO: 500 mVrms (100% modulation)/ Impedance: 47 kilohms HDMI IN 1/2 HDMI: Video: 480i, 480p, 720p, 1080i, 1080p / Audio: Two channel linear PCM 32, 44.1 and 48 kHz, 16, 20 and 24bits AUDIO (HDMI IN 2 only): 500 mVrms (100% modulation)/ Impedance: 47 kilohms AUDIO OUT 500 mVrms (100% modulation)/ More than 1 Vrms at the maximum volume setting (Variable)/ More than 500 mVrms (Fixed) PC IN D-sub 15-pin, analog RGB, 0.7 Vp-p, 75 ohms, positive See the PC Input Signal Reference Chart on page 18. PC AUDIO INPUT Stereo mini jack, 500 mVrms, 1 kilohm Headphones Stereo mini jack / Impedance: 16 ohms Power and others Power requirement 120 V-240 V AC, 50/60 Hz Power consumption in use 105 W in standby All models less than 0.1 W 26 Screen size (inches measured diagonally) 158 W 180 W 215 W 31.5 (32 class) 40 46 Display resolution (horizontal × vertical) 1,366 dots × 768 lines Speaker/Full range (2) 42 × 150 mm 1 11/16 × 6 inches 42 × 150 mm 1 11/16 × 6 inches 55 × 150 mm 2 1/4 × 6 inches 70 × 130 mm 2 3/4 × 5 7 /16 inches with stand (mm) (inches) 656 × 500 × 214 26 7/8 × 19 3/4 × 8 1/2 790 × 577 × 214 31 1/8 × 22 3/4 × 8 1/2 981 × 692 × 265 38 5/8 × 27 1/4 × 10 1/2 1114 × 778 × 306 43 7/8 × 30 3/4 × 12 1/8 without stand (mm) (inches) 656 × 452 × 96 25 7/8 × 17 7/8 × 3 7/8 790 × 530 × 100 31 1/8 × 20 7/8 × 4 981 × 643 × 110 38 5/8 × 25 3/8 × 4 3/8 1114 × 730 × 115 43 7/8 × 28 3/4 × 4 5/8 wall-mount hole pattern (mm) 200 × 100 200 × 200 300 × 200 300 × 200 with stand 13.5 kg 30 lb. 17.0 kg 38 lb. 25.0 kg 56 lb. 32.0 kg 71 lb. without stand 11.0 kg 25 lb. 14.5 kg 32 lb. 21.0 kg 47 lb. 27.5 kg 61 lb. Dimensions Mass Supplied accessories Remote control RM-YD018 (1) / Size AA batteries (2) / AC power cord (1) / Support belt (1) / Securing screw (1) / Wood screw (1) / Cable holder (1 attached to the TV) / Operating Instructions (1) / Quick Setup Guide (1) / Warranty Card (1) / Online Registration Card (U.S.A. only) (1) Optional accessories Headphones plug adapter / Connecting cables / Wall-Mount Bracket: SU-WL100 (KDL-26S3000), SU-WL500 (KDL-32S3000/KDL-40S3000/KDL-46S3000) / TV stand: RHT-G800 (for all models excluding KDL-26S3000) ~ • Optional accessories availability depends on its stock. • Design and specifications are subject to change without notice. 44 Index 0-9 buttons 23 4:3 Default 33 French Rating 38 H A AC IN 15 Add Digital Channels 35 Advanced Settings 31 Analog CC 36 Audio Out 34 AUDIO OUT jack, described 15 Auto Adjust 33 Auto Program 21, 35 Auto S Video 39 Auto SAP, MTS setting 34 Auto Wide 33 B Backlight 31 Balance 32 Bass 32 Bilingual audio 34 Brightness 31 C Cable 35 Cable holder 20 CC button 25 CC Display 36 CH +/– button 25 Channel Block 37 CineMotion 34 Color 31 Color Temperature 31 COMPONENT IN jack (1080p/1080i/ 720p/480p/480i), described 15 Contact Sony 30 Country 36 Current Time 30 D Device Auto Power Off 39 Device List 39 Digital CC 36 DIGITAL OUT (OPTICAL) jack, described 15 Digital Rating 37 Display Area 33 DISPLAY button 22 Display Options 36 DMex button 23 DMex, described 15 E Edit Channel Labels 35 English Rating 38 ENT button 23 F H Center 33 HDMI Control 39 HDMI IN jack, described 15 Headphones jack, described 13 HOME button 23 Hue 31 I Info Banner 40 Infrared Receiver (IR) 26 INPUT button 25 Installing the TV on a wall 12 J JUMP button 25 L Label Inputs 39 Language 40 Light Sensor Described 26 Setting 40 M Movie Rating 38 MPEG Noise Reduction 31 MTS 34 MUTING button 24 N Noise Reduction 31 O OPTIONS button 25 P P&P 27 Password 36 PC IN jack, described 15 PC Power Management 40 Phase 33 PIC OFF/TIMER LED 26 Picture 31 PICTURE button 23 Picture Mode 30 PIP 27 Pitch 33 POWER button 24 POWER LED 26 Power Saving 40 R Rating 37 Reset 31, 32, 33, 43 RETURN button 23 S S VIDEO jack, described 13, 15 Screen Position 33 Setting up channels 21 Settings Audio Options 34 Channel 35 Clock/Timers 30 Closed Captions (CC) 36 External Inputs 39 General 40 HDMI Settings 39 Initial Setup 40 Parental Lock 36 Picture 30 Product Support 30 Screen 32 Sound 32 Video Options 34 Sharpness 31 Show/Hide Channels 35 Signal Diagnostics 30 SLEEP button 22 Sleep Timer 30 Sound Booster 32 Sound Mode 32 Speaker 26 Speakers 34 STANDBY LED 26 Steady Sound 32 Surround 32 T Timer 30 Timer Settings 30 Treble 32 Troubleshooting 41–43 TV Auto Power On 39 TV Rating 38 U U.S.A. Rating 38 Unrated 37 V V Center 33 Vertical Size 33 VHF/UHF/CABLE input, described 15 VIDEO IN jack, described 13, 15 VIDEO/AUDIO (L/R) jacks, described 13, 15 VOL +/– button 24 Volume Offset 32 W WIDE button 24 Wide Mode 32, 34 FAVORITES button 23 FREEZE button 23 45 For Your Convenience Please contact Sony directly if you: z z Have questions on the use of your television after reading your Operating Instruction manual and Quick Setup Guide Experience difficulty operating your television Contact Sony Customer Support at: http://www.sony.com/tvsupport or to speak with a support representative: United States 1-800-222-SONY (7669) Canada 1-877-899-SONY (7669) Sony will work to resolve your questions more quickly than your retailer or place of purchase. Please Do Not Return the Product to the Store Printed in U.S.A.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project