Surround Kit Installation Guide

Surround Kit Installation Guide
Refrigerator Surround Kit
For Models E388, E450, E402B, E411T, E415H, E440T, E442B, E521T and E522B, RF610A, RF540A, RF201A
Kit Application
This kit is designed to be used with 1695mm to 1780mm
(66 3/4” to 70 1/8”) High cabinet models, incorporating the “B” series
onwards refrigerators with curved & flat door styling.
Note: This kit can be used for combining any of the following
products, E388, E450, E402B, E411T, E415H, E440T, E442B, E521T,
E522B, RF610A, RF540A, RF201A
(Part number for each installation type on page 4)
To give the most integrated look, the kitchen cabinetry should be
flush with the front of the refrigerator door.
Tools Required
•
•
•
•
•
No. 2 square type drill bit - long
Electric drill
Flat blade screwdriver
1 x 16mm (11/16in) piece of MDF the same size as the base of
the cavity.
Joiner kit (part number 813690) required if joining two
refrigerators side by side.
Parts Included in Kit
Top Trim Brackets
(2) Single Refrigerator Kits
(3) Two Refrigerator Kits
Side Trim Brackets (10)
Screw Type A:
#8x12 Square Drive CSK (26)
Top Trim (1)
Side Trim (2)
Bottom Trim (1)
Fisher and Paykel Refrigerator Surround Kit
Installation Procedure
Step 1
1
Check that the internal Cupboard Cavity dimensions are correct (see diagram 1).
2Unpack the refrigerator and/or freezer cabinets from their separate delivery cartons (see individual cartons for unpacking procedures).
3
Ensure the floor and/or the cupboards are protected from damage during the unpacking and assembly of the cabinets.
4
Check the refrigerator and freezer doors are hinged on the desired side.
5
Check that the kit is complete (refer to kit parts list on page 1).
Note 1: Due to the size of the refrigerator cabinets, it is essential that assembly of the kit be undertaken with a minimum of two able-bodied persons.
Note 2: It is important to include adequate venting to the top of the cabinet to ensure the efficient operation of the refrigerator.
Diagram 1: Cutout Dimensions (flush to edge of door)
All Dimensions are quoted in millimetres & inches
Width of models mm - inch
790 model
900 model
Width A
Depth B*
Height C
Air Vent D
962 - 37 7/8”
700 - 27 9/16”
1806 - 71 1/8”
200 - 8”
1072 - 42 1/4”
700 - 27 9/16”
1891 - 74 1/2”
200 - 8”
635 model + 635 model
1467 - 57 49/64”
700 - 27 9/16”
1806 - 71 1/8”
200 - 8”
680 model + 680 model
1557 - 61 19/64”
700 - 27 9/16”
1806 - 71 1/8”
200 - 8”
790 model + 790 model
1777 - 70”
700 - 27 9/16”
1806 - 71 1/8”
200 - 8”
* Depth is a minimum requirement
Cut out dimensions above are to be used as minimum dimensions.
Step 2
1Locate the two/three top trim brackets.
2
For two refrigerator kits, one bracket is to be screwed in the top centre of the cabinet, secure the top bracket with two of the screws
(Type A, #8 x 12 SQ Drive CSK).
3
For all kits, the remaining two brackets are to be secured on either side, by two screws which are mounted from the side (see diagram 2).
4Looking at the front of the product, place the top brackets on top of the cabinet.
5
Care must be taken to line up the top front edge of the brackets with the leading edge of the cabinet.
Diagram 2: Top Trim Brackets
Fisher and Paykel Refrigerator Surround Kit
Step 3
1Locate the ten side trim brackets.
2
Position five brackets to the left hand side of the cabinet’s and the remaining five brackets to the right hand side of the cabinet’s.
3
Brackets should be evenly spaced down each side (see diagram 3). Secure each of these brackets with the two screws provided.
4
Care must be taken to line up the front edge of the brackets with the leading edges of the cabinet.
Diagram 3: Side Trim Brackets
Step 4
Place 16mm (11/16in) piece of MDF the same size as the base of the cavity into cavity. See diagram 4.
Diagram 5: Trim Installation
Diagram 4: MDF Board
16mm (11/16in) MDF Board Insert
Step 5
1 Remove protective coating film from surround trim.
2 To install the surrounds, first clip in top surround.
3 Ensure the locater strips at the rear of the top brackets clip into the rear of the top trim, then clip both side trims into place starting
from the front cabinet edge.
4Lastly install the bottom trim. The bottom trim requires an 16mm (11/16in) piece of MDF the same size as the base of the cavity to sit on. See
diagram 4.
Step 6
1If installing two refrigerators/freezers side by side a joiner kit is required (part number 813690). Refer to these instructions and fit joiner kit
before pushing refrigerator into place, see diagram 5.
2 Plug refrigerator into electrical socket, run water connection to refrigerator if required (Ice & Water models only).
3Gently install refrigerator into cabinetry making sure it is centred within the surround trim.
The front of the refrigerator door should be flush with the front of the cabinetry to obtain an integrated look.
Fisher and Paykel Refrigerator Surround Kit
Kit Part Numbers and Cut Out Dimensions Table
Part Numbers
Refrigerator Model Width
Brushed Stainless
Iridium Stainless
1 x 790 LH
818 758
814 678
2 x 790
818 759
814 679
2 x 680
818 760
2 x 635
Cut Out Dimensions
Width A
Depth B*
Height C
962mm
37” 7/8
700mm
27” 9/16
1806mm
71” 1/8
813690
1777mm
70”
700mm
27” 9/16
1806mm
71” 1/8
814 680
813690
1557mm
61” 19/64
700mm
27” 9/16
1806mm
71” 1/8
818 761
814 681
813690
1467mm
57” 49/64
700mm
27” 9/16
1806mm
71” 1/8
1 x 790 RH
818 762
814 682
962mm
37” 7/8
700mm
27” 9/16
1806mm
71” 1/8
1 x 900
818 763
814 683
1072mm
42” 1/4
700mm
27” 9/16
1891mm
74” 1/2
* Depth is a minimum requirement
Part Number: 819150
June 2007
Plus Joiner Kit
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement