30" (76.2 cm) ELECTRIC DOWNDRAFT SLIDE-IN RANGES

30" (76.2 cm) ELECTRIC DOWNDRAFT SLIDE-IN RANGES
30" (76.2 cm) ELECTRIC DOWNDRAFT SLIDE-IN RANGES
PRODUCT MODEL NUMBERS
JES9750CA
PRODUCT DIMENSIONS
JES9800CA
JES9860CA
ELECTRICAL REQUIREMENTS
A
To properly install your range, you must determine the type of
electrical connection you will be using and follow the instructions
provided for it here.
Range must be connected to the proper electrical voltage and
frequency as specified on the model/serial number rating plate.
The model/serial number rating plate is located behind the control
panel or on the oven frame behind the storage drawer panel. Refer
to the figures in the “Product Dimensions” section.
● This range is manufactured with the neutral terminal connected to
the cabinet. Use a 3-wire, UL listed, 40- or 50-amp power supply
cord (pigtail) (see following Range Rating chart). If local codes do
not permit ground through the neutral, use a 4-wire power supply
cord rated at 250 volts, 40 or 50 amps and investigated for use
with ranges.
●
Range Rating*
Specified Rating of
Power Supply Cord Kit
and Circuit Protection
120/240 Volts
120/208 Volts
Amps
8.8 - 16.5 KW
16.6 - 22.5 KW
7.8 - 12.5 KW
12.6 - 18.5 KW
40 or 50**
50
*The NEC calculated load is less than the total connected load
listed on the model/serial rating plate.
**If connecting to a 50-amp circuit, use a 50-amp rated cord with
kit. For 50-amp rated cord kits, use kits that specify use with a
nominal 1³⁄₈" (34.9 mm) diameter connection opening.
F
B*
E**
A. 30 " (78.1 cm)
B. 35 " (90.8 cm) height to underside
D
of cooktop edge with leveling legs
screwed all the way in*
C. Model/serial number plate (located
on the right-hand side of the
bottom oven frame)
D. 29 " (75.9 cm)
E. 29 " (73.8 cm) from handle to standoff at back of range**
countertop notch to rear of cooktop
C
*Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm)
countertop; front of oven door protrudes 2 " (6.4 cm) beyond
24" (61.0 cm) base cabinet.
CABINET OPENING DIMENSIONS
Cabinet opening dimensions shown are for 25" (64.0 cm)
countertop depth, 24" (61.0 cm) base cabinet depth and
36" (91.4 cm) countertop height.
A
B
C
D
H
E
I
I
F
G
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
A. 13" (33.0 cm) upper cabinet depth
B. 30" (76.2 cm) min. opening width
C. For minimum clearance to the top of the cooktop, see NOTE.
D. 23 " (59.1 cm) opening depth
E. 30" (76.2 cm) min. opening width
F. Junction box - 5.5" (14.0 cm) min. from either cabinet, 10" (25.4 cm)
max. from floor. Outlet must be flush. Nothing located in shaded
area can extend more than 2" (5.1 cm) from wall or range will not
slide all the way back.
G. Cabinet door or hinge should not extend into cutout.
H. 18" (45.7 cm)
I. 3" (7.6 cm) min. clearance from both sides of the range to the side
wall or other combustible material.
NOTE: 24" (61.0 cm) minimum when bottom of wood or metal
cabinet is covered by not less than ¹⁄₄" (0.64 cm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel,
0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or
0.020" (0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking
platform and the bottom of an uncovered wood or metal cabinet.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10253462A
8-10-09
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement