Viking Range VUWC1441T, DFUW1541C, DUWC1441C, DFUW2441C, DFUW1441C, VUWC1441, DUWC1541C, VUWC2441, VUWC1541C User guide

Viking Range VUWC1441T, DFUW1541C, DUWC1441C, DFUW2441C, DFUW1441C, VUWC1441, DUWC1541C, VUWC2441, VUWC1541C User guide
Viking Use/Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
Undercounter/Freestanding Wine Cellars
F20729A EN
(071610)
IMPORTANT - PLEASE READ AND FOLLOW
GENERAL INFORMATION
•
•
•
•
•
Unpack
1. Remove banding from bottom of carton. Lift carton up and off of the wine cellar
2. Remove all tape and packaging material from the outside and inside of the cabinet.
3. Keep all carton packaging until your wine cellar has been thoroughly inspected and found to be in good condition.
Before beginning, please read these instructions completely and carefully.
Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
Please observe all local and national codes and ordinances.
Please ensure that this product is properly grounded.
The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future reference.
A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local
ordinances.
• The required use of a GFI is normally related to the location of a receptacle with respect to any
significant sources of water or moisture.
• Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which are not
installed properly or do not meet the requirements below.
If
•
•
•
•
•
•
•
the use of a GFI is required, it should be:
Of the receptacle type (breaker type or portable type NOT recommended)
Used with permanent wiring only (temporary or portable wiring NOT recommended)
On a dedicated circuit (no other receptacles, switches or loads in the circuit)
Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT recommended)
Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard)
In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
Protected from moisture (water, steam, high humidity) as much as reasonably possible
WARNING
To reduce the risk of fire, electric shock, or injury when using your unit, follow these basic precautions:
• Read all instructions before using the unit.
• Never allow children to operate, play with, or crawl inside the unit.
• Never clean unit parts with flammable fluids. The fumes can create a fire hazard or explosion.
• Always turn the power on/off switch (located behind the air grille on top right side) to the OFF position before attempting to change
light bulbs, clean, or service the unit.
AREA REQUIREMENTS
1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in
on the top and three sides, but the front MUST BE unobstructed for air circulation and proper operation.
Installation should be such that the cabinet can be moved for servicing if necessary.
2. Unit should be in a well ventilated area with temperature above 55°F (13°C) and below 110°F (43°C). Best results
are obtained at temperatures between 65°F (18°C) and 80°F (27°C) for built-in models and 65°F (18°C) and 90°F
(32°C) for freestanding models.
3. Provisions for electricity should be determined before placing unit in proper place.
Units Certified for Outdoor Use - outdoor models contain a T after the base model number (ex. VUWC144T) and
have a stainless steel outer cabinet.
1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in
on the top and three sides, but the front MUST BE unobstructed for air circulation and proper operation.
Installation should be such that the cabinet can be moved for servicing if necessary.
2. Unit should be in a well ventilated area with temperature above 40°F (4.4°C) and below 110°F (43°C). Best results
are obtained at temperatures between 60°F (16°C) and 100°F (38°C).
3. Provisions for electricity should be determined before placing unit in proper place.
UNDERCOUNTER CABINET CUTOUT
FOR YOUR SAFETY
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER
APPLIANCE. THE FUMES CAN CREATE A FIRE HAZARD OR EXPLOSION.
It
•
•
•
•
is your responsibility to be sure your wine cellar is:
located so the front is not blocked to restrict incoming or discharge air flow.
properly leveled.
located in a well ventilated area.
connected to the proper kind of outlet, with the correct electric supply and grounding. A 115V, 60 Hz, 15 amp fused electrical
supply is required. NOTE: Time delay fuse or circuit breaker is recommended.
• not used by anyone unable to operate it properly.
• used only for its intended purpose.
• properly maintained.
A
B
C
15” W. Models
24” W. Models
15” (38.1 cm)*
Min. 34-1/4” (87.0 cm)
Max. 35” (88.9 cm)
24” (61.0 cm)
24” (61.0 cm)*
Min. 34-1/4” (87.0 cm)
Max. 35” (88.9 cm)
24” (61.0 cm)
*Add 1/4” (.64 cm) to cutout width if door is recessed between cabinets.
•SAVE THESE INSTRUCTIONS•
PROPER DISPOSAL (OF OLD REFRIGERATION UNIT)
DANGER
A
RISK OF CHILD ENTRAPMENT
Before You Throw Away Your Old Refrigeration Unit:
• Take off the doors.
• Leave the shelves in place so that children may not easily
climb inside.
B
IMPORTANT: Child entrapment and suffocation are not problems of the past.
Junked or abandoned refrigeration units are still dangerous... even if they will sit for
“just a few days.”
IMPORTANT:
Now that you have a new wine cellar, it is extremely important that you dispose of your
old appliance in a way that minimizes the possibility that children will find it. There
have been many cases in years past of children crawling inside junked and abandoned
refrigeration units and becoming trapped or suffocated.
C
Contact your municipal waste disposal authority to find out the best and safest way to
dispose of your old refrigeration unit.
2
3
SPECIFICATIONS/DIMENSIONS
PROFESSIONAL - 15”W. Models
SPECIFICATIONS/DIMENSIONS
DESIGNER - 15”W. Models
Basic Electric Data
•115 VAC/60 Hz
•Maximum amps - 3.0
Approximate Shipping Weight - 110 lbs. (49.5 kg)
Basic Electric Data
•115 VAC/60 Hz
•Maximum amps - 3.0
Approximate Shipping Weight - 110 lbs. (49.5 kg)
Dimensions
VUWC 15”W.
Dimensions
DUWC 15”W.
14
(37-3/4
.5 ”
c
14
(37-3/4
.5 ”
cm
)
3
(86 4”
.4
mi cm)
n.
34 to
(88-3/4
.3 ”
cm
m
(w ax )
i th
.
l
30
(78-3/4
.1 ”
cm
)
Door Swing
DUWC 15”W.
14-3/4”
(37.5 cm)
m)
3
(86 4”
.4
mi cm)
n.
34 to
(88-3/4
.3 ”
m cm
(w ax )
ith
.
l
30
(78-3/4
.1 ”
cm
)
e
leg veli
s f ng
ex ull
te n y
de
d)
e
leg veli
n
s
ex full g
te n y
de
d)
6”
1
/
-3 )
21 .8 cm
(53.8 cm)
23-5/8”
(60.0 cm)
2-1/2”
26-1/8”
(6.4 cm)
(66.4 cm)
”
16)
/
3
1- cm
2 3.8
(5
/8”)
5
23 .0 cm
(60 /8”
-1 )
26 .4 cm
(53
/8”)
5
3 m
2 .0 c
(60
/8”)
1
26 4 cm
37-3/16”
90.0°
(94.5cm)
(66
.
(66
Door Swing
VUWC 15”W.
21-3/16”
Dimensions
DFUW 15”W.
14
(37-3/4
.5 ”
c
14-3/4”
(37.5 cm)
Door Swing
DFUW 15”W.
14-3/4”
(37.5 cm)
m)
3
(86 4”
.4
mi cm)
n.
34 to
(88-3/4
.3 ”
m cm
(w ax )
ith
.
l
30
(78-3/4
.1 ”
21-3/16”
(53.8 cm)
cm
)
23-5/8”
(60.0 cm)
(6.4 cm)
(66.4 cm)
37-3/16”
90.0°
(94.5 cm)
4
(53.8 cm)
23-7/16”
(59.5 cm)
to front of
locally supplied
custom panel
e
leg veli
s f ng
ex ull
te n y
de
d)
2-1/2”
26-1/8”
21-3/16”
”
/16)
3
213.8 cm
(5
”
16)
/
7
239.5 ctmof d
37-3/16”
90.0°
(5 fron plie
(to y supanel)
all p
loc stom
cu
5
(94.5cm)
SPECIFICATIONS/DIMENSIONS
PROFESSIONAL - 24” W. Models
SPECIFICATIONS/DIMENSIONS
DESIGNER - 24” W. Models
Basic Electric Data
• 115 VAC/60 Hz
• Maximum amps - 3.3
• Approximate Shipping Weight
Single Zone - 140 lbs. (63.2 kg)
Dual Zone - 170 lbs. (76.5 kg)
Basic Electric Data
• 115 VAC/60 Hz
• Maximum amps - 3.3
• Approximate Shipping Weight
Single Zone - 140 lbs. (63.2 kg)
Dual Zone - 170 lbs. (76.5 kg)
Dimensions VUWC 24”W. - Single Zone
Dimensions DUWC 24”W. - Single Zone
23
Dimensions VUWC 24”W. - Dual Zone
23
(60-7/8
.6 ”
cm
)
23
(60-7/8
.6 ”
cm
)
(60-7/8
.6 ”
cm
)
30
30
3
(78-3/4
.1 ”
cm
)
30
(8634”
.4
mi cm)
n
34 to .
(88-3/4
.3 ”
c
(w max m)
ith
le .
(78-3/4
.1 ”
cm
)
(86 4”
.4
mi cm)
n.
34 to
(88-3/4
.3 ”
m cm
(w ax )
i th
.
l
”
22 cm)
.9
.9
(6
(55
.9
8”
-7/cm)
3
2
(61
.9
/8”)
3
26 cm
(68
(60
/8”)
7
26 cm
8.3
(6
Door Swing VUWC 24”W. - Single Zone
”
22 cm)
/2”)
1
21 cm
(54
8”
-3/cm)
4
2
(61
e
leg veli
n
s
ex full g
te n y
de
d)
leg vel
i
ex s ful ng
ten ly
de
d)
e
leg veli
s f ng
ex ull
te n y
de
d)
(55
/8”)
3
24 cm
.6
/8”)
7
26 cm
.7
7.0
Door Swing VUWC 24”W. - Dual Zone
23-7/8”
23-7/8”
(60.6 cm)
(60.6 cm)
Door Swing DUWC 24”W. - Single Zone
21-1/2”
22”
(54.6 cm)
(55.9 cm)
23-7/8”
(61.9 cm)
(60.7 cm)
26-7/8”
22”
(55.9 cm)
24-3/16”
(61.4 cm)
(61.9 cm)
2-1/2”
(67.0 cm)
(6.4 cm)
23-7/8”
(60.6 cm)
24-3/8”
26-3/8”
2-1/2”
Door Swing DFUW 24”W. - Single Zone
23-7/8”
22”
24-3/8”
.3
(60.6 cm)
(55.9 cm)
(68.3 cm)
3
(86 4”
.4
mi cm)
n.
34 to
(88-3/4
.3 ”
m cm
(w ax )
i th
.
l
(78-3/4
.1 ”
cm
)
to front of
locally supplied
custom panel
2-1/2”
26-7/8”
(6.4 cm)
(68.3 cm)
(6.4 cm)
47-1/4”
90.0°
47-1/4”
90.0°
(120.0 cm)
90.0°
46-1/2”
47-1/4”
(120.0 cm)
(120.0 cm)
90.0°
(118.1 cm)
6
7
SPECIFICATIONS/DIMENSIONS
DESIGNER - 24” W. Models
CUSTOM WOOD FRAME INSTALLATION (DFUW Model)
NOTE: Weight of wood panel must not exceed 20 lbs.
Basic Electric Data
• 115 VAC/60 Hz
• Maximum amps - 3.3
• Approximate Shipping Weight
Single Zone - 140 lbs. (63.2 kg)
Dual Zone - 170 lbs. (76.5 kg)
Step 1: Verify door alignment
The door should be parallel to the sides and top of the refrigerator. If alignment is necessary the door may be
adjusted by loosening the 2 screws which secure the hinge adapter brackets to the door and adjusting the door side
to side. Use a 5/32” allen wrench for this procedure. (See Figure 1 below).
Top hinge pin Remove to remove
the door
Dimensions DFUW 24”W. - Dual Zone
23
(60-7/8
.6 ”
cm
)
30
(8634”
.4
mi cm)
n
34 to .
(88-3/4
.3 ”
c
(w max m)
i th
le .
(78-3/4
.1 ”
cm
)
Hinge adaptor screws Loosen these to adjust
door, on the top and
bottom of the door
Door must be
parallel to top and
sides of refrigerator
9/32”
(7 mm)
leg vel
i
ex s ful ng
te n l y
de
d)
/2”)
1
21 cm
(54
.6
/8”)
7
23 cm
(60
.7
Door Swing DFUW 24”W. - Dual Zone
Figure 1
23-7/8”
(60.6 cm)
Step 2: Remove door
Remove the top hinge pin from the hinge with an 1/8” allen wrench. Remove the door by angling the top of the door
outward and lifting the door off the bottom hinge. (See detail in Figure 1).
21-1/2”
(54.6 cm)
23-11/16”
Step 3: Remove gasket
Lay the door on its front being careful not to scratch it. Remove the door gasket by peeling up and out of the channel.
(60.2 cm)
to front of
locally supplied
custom panel
Step 4: Cut overlay panel
Depending on the refrigerator model cut the overlay panel to the dimensions shown. Use Figure 2 and Table A.
46-1/2”
(118.1 cm)
Note: For overlay with lock option, panel thickness to be 3/4” (19 mm) maximum to 5/8” (16 mm) minimum.
90.0°
Note: For the door closer to work properly, it is necessary to maintain a minimum space of 9/32” (7mm) between the
door and cabinet flange as shown. This space can be adjusted by adjusting the top and bottom hinge adapters.
8
9
CUSTOM WOOD FRAME INSTALLATION (DFUW Model) (cont.)
CUSTOM WOOD FRAME INSTALLATION (DFUW Model) (cont.)
W
Model
H
Front of
overlay
panel
W
H
1-23/32”
(38.8 cm)
15”
14-5/16”
(36.4 cm)
30-5/16”
(76.9 cm)
Typical 4
Sides
24”
23-7/16”
(59.5 cm)
30-5/16”
(76.9 cm)
Table A
Glass Door Models
Step 7: Mark and drill lock hole
Locate and mark with a pencil the location of the lock hole on the overlay panel, this is the hole in the top corner of
the handle side of the door. Remove the clamp and remove the overlay panel from the door. On the backside of the
panel where you marked the lock location drill a 13/16” (20.5 mm) diameter counter bore 7/16” (11.0 mm) deep into
the overlay panel. Drill a 15/32” (12.0 mm) diameter hole through the overlay panel centered on the counterbore
being careful not to splinter the wood on the face side of the panel. (See Figure 3).
Step 8: Assemble the lock parts
Two (2) lock extensions are supplied with the lock. Use the longer extension for a 3/4” thick overlay panel and the
shorter one for a 5/8” thick panel. Assemble the lock extension, cam stop washer, spring washer, and set screw to the
lock as shown in Figure 3 and 4.
Install this assembly into the overlay panel and secure with the retaining nut using a 15mm socket. Make sure the key
slot in the lock is vertical.
brass extension
Figure 2
Glass Door Models
spring washer
nut
Step 5: Clamp panel to door
Set the overlay panel on the door front, align the edges, and clamp together. Clamp the panel firmly but be careful
not to crush the foam in the door or scratch the door.
Step 6: Drill holes in overlay panel
Remove the hinge adapter bushings from the top and bottom door hinge adapters. (See Figure 6). Using the holes in
the hinge adapters drill 5/16” (8 mm) diameter clearance holes into the overlay panels 3/4” (20 mm) deep. These will
be clearance holes for the top and bottom hinge pins.
Also, at this time, drill the screw pilot holes for attaching the overlay panel to the door. Select the size of the hole from
Table B. Be careful not to drill the pilot holes through the overlay panel but only 1/2” (12.7 mm) deep.
cam
lock
Phillips screw
15/32”
hole
13/16”
counter bore
7/16” deep
inner door
Material Type
Hardwood
Softwood
#8 Wood Screw
3/32” (2.4 mm) Diameter. Pilot Hole
5/64” (2.0 mm) Diameter. Pilot Hole
Table B
10
3/4”
wood panel
Section A-A
Scale 1:1
Figure 3
11
CUSTOM WOOD FRAME INSTALLATION (DFUW Model) (cont.)
CUSTOM WOOD FRAME INSTALLATION (DFUW Model) (cont.)
Top hinge pin
Top hinge
Top door hinge
adapter
Top hinge adapter
bushing
Bottom door
hinge adapter
Figure 4
Step 9: Secure overlay panel to the door
With the #8 wood screws provided, fasten the overlay panel to the door. (See Figure 5).
Step 10: Install lock cam
Attach the lock cam to the back of the lock assembly with the Phillips head machine screw provided. Orient the lock
cam vertically when installing on the lock.
Step 11: Install door gasket
Press the door gasket into the door channel. Make certain the gasket corners are fully inserted. If applicable insert the
key into the lock and make certain the lock operates properly.
Bottom hinge
adapter bushing
Bottom hinge
with cam
Bottom hinge pin
Step 12: Install the door
Install the top and bottom hinge adapter bushings back into the hinge adapters that were removed in Step 6. Install
the door by reversing the procedure from Step 2. Install the top hinge pin so the screw head is flush with the top
surface of the hinge. If applicable insert key into lock and verify the lock cam works properly with the catch bracket on
the front of the refrigerator cabinet.
Figure 6
Right Hand
hinges shown
Clearance hole through
door gasket channel
LEG LEVELER INSTALLATION
Read Before Installing Leg Levelers
WARNING
#8 Wood Screw
Do not lay unit on top, side, back, or front. If unit is accidentally laid in
any position other than right side up, then the unit must remain in the
upright position for at least 24 hours before plugging the unit in.
1. Four leveling legs are pre-installed in the base of the unit at the factory.
Back of door
Figure 5
12
2. The unit should be leveled from front to back and side to side. If floor
conditions do not allow the unit to sit level, adjust the leg levelers by turning
the required leg leveler counter-clockwise to increase the height and clockwise
to reduce the height.
13
ELECTRICAL CONNECTION
LIGHT TUBE REPLACEMENT - 24” W. Single Zone Models
WARNING
DANGER
ELECTRICAL SHOCK HAZARD
ELECTRICAL SHOCK HAZARD
Failure to follow these instructions could result in fire or electrical shock.
Electrical Requirements
A 115 volt, 60 Hz, AC only 15 amp fused electrical supply is required. (A time
delay fuse or circuit breaker is recommended.) It is recommended that a
separate circuit, serving only this appliance, be provided.
•ELECTRICAL GROUND IS REQUIRED ON THIS APPLIANCE.
•DO NOT UNDER ANY CIRCUMSTANCES REMOVE THE POWER SUPPLY
CORD GROUND PLUG.
•DO NOT USE AN EXTENSION CORD.
Grounding type
wall receptacle
Failure to to disconnect the power cord when changing the light tube,
could result in fire or electrical shock.
NOTE: Please contact your Viking Range Corporation parts distributor or dealer to order new light tubes. Use only
approved replacement light tubes from your dealer or manufacturer.
Power Supply
with 3-prong
grounding plug
Recommended Grounding Methods
For your personal safety, this refrigeration product must be grounded. This appliance is equipped with a 5’ power
supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a
mating 3-prong grounding type wall receptacle grounded in accordance with the National Electrical Code and local
codes and ordinances. If the circuit does not have a grounding type receptacle, it is the responsibility and obligation of
the customer to exchange the existing receptacle in accordance with the National Electrical Code and applicable local
codes and ordinances. The third ground plug SHOULD NOT, under any circumstances, be cut or removed. All UL listed
refrigerated products are equipped with this type of plug.
FINAL PREPARATION
1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior of the wine
cellar should be washed thoroughly with hot, soapy water, rinsed and wiped dry to remove film residue and any
installation dust or debris before being used. Solutions stronger than soap and water are rarely needed.
2. All stainless steel parts should be wiped with hot soapy water. If buildup occurs, do not use steel wool, abrasive
cloths, cleaners, or powders. If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot,
wet cloths to loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other
metal tool to scrape stainless steel; scratches are almost impossible to remove.
This product uses two 6-watt light tubes to illuminate the interior
of the wine cellar. The light tubes are very reliable electrical
components, but should either or both light tubes not function
properly, please call your local dealer for replacement light tubes.
To replace the light tube:
•Use a small Phillips head screwdriver to remove the two screws
holding the cover plate over the back section of the light tube.
Set the screws and cover plate aside for re-assembly later.
•Using a small flat-blade screwdriver, gently lever the front section
Light tube
of the light tube down to allow it to be pulled clear of the light
Connectors
housing. Disconnect the two insulated electrical connectors from
the cabinet's electrical cable and discard the old light tube.
Cover plate
•Reconnect the insulated electrical connector of the new light tube
to the cabinet's electrical cable connectors. Make sure they are
Screws
secure and fully inserted.
•Carefully realign the light tube's electrical terminals back into the rear of the light enclosure channel making sure not
to crimp them. Gently insert the light tube along the length of the light enclosure channel. Press the light tube gently
into the light enclosure channel. Only a small part of the light tube should project below the ceiling of the unit. DO
NOT USE A HAMMER TO FIT THE LIGHT TUBE.
•Place the light tube terminal cover plate back in its original position on the light enclosure's flange. Re-use the original
two screws to secure the cover in place. Plug the unit into the electrical socket. Check to see if the light tubes operate
properly.
LIGHT TUBE REPLACEMENT - 24” W. Dual Zone Models
LIGHT ASSEMBLY REPLACEMENT - 15” W. Models
DANGER
DANGER
ELECTRICAL SHOCK HAZARD
ELECTRICAL SHOCK HAZARD
Failure to to disconnect the power cord when changing the light tube,
could result in fire or electrical shock.
NOTE: Please contact your local Viking Range
Corporation parts distributor or dealer to order a
new light assembly.
Green
ground wire
Light
assembly
Hex head
screw
Hex head
To replace the light, first disconnect the unit’s power
screw
cord. Next, remove both the green ground wire
Plug
screw located on the left of the light assembly and
the other screw located on the right of the light assembly with a 5-16” hex head screwdriver. (See drawing). Unplug
the light unit and remove complete light assembly.
Failure to to disconnect the power cord when changing the light tube,
could result in fire or electrical shock.
NOTE: Please contact your Viking Range Corporation parts distributor or dealer to order new light tubes. Use only
approved replacement light tubes from your dealer or manufacturer.
This product uses two light tubes to illuminate the interior of the wine cellar. There is one light tube located behind the
control housing in the the upper compartment and one light tube attached to the underside of the cabinet divider in
the lower compartment.
Use replacement instructions and drawing from the 15”W. Models for this Dual Zone product.
To install the new light assembly, screw in the green ground wire screw and the screw located on the right with a 5/16”
hex head screwdriver and plug the light unit in.
14
15
SETTING THE CONTROLS - SINGLE ZONE
The temperature of the wine cellar ranges from 40ºF (4ºC) to 65°F (18ºC).
TruProtect™ “Basic” Function “Quick” Reference
Solid Door Single Zone Models:
55˚
Glass Door Single Zone Models:
55 ˚F
ON
OFF
TruProtect System
WARMER
F/C
SET
COLDER
POWER FAILURE - Flashing Amber
55 ˚F
ON
OFF
HIGH/LOW TEMP - Red
ALARMS OFF - Steady Amber
PRESS ON/OFF - Reset
PRESS AND HOLD
WARMER
˚̊F/C
COLDER
LIGHT
SET
TruProtect System
POWER FAILURE - Flashing Amber
HIGH/LOW TEMP - Red
ALARMS OFF - Steady Amber
PRESS ON/OFF - Reset
PRESS AND HOLD
WARMER
ON
OFF
˚̊F/C
SET
LIGHT
COLDER
Function
Function Access
WARMER
ON
OFF
Control Confirmation/Comment
˚̊F/C
SET
LIGHT
COLDER
WARMER
Turn Unit On & Off
Pressing and holding the
˚̊ ill tu r n th e un it “O N” or “OFF ”.
key for 5-seconds w
ON
OFF
F/C
SET
LIGHT
Disp55la˚Fy wi13ll ˚Cbe b38la˚Fnk
COLDER
when refrigeration sytem is off. Lights will still function, but will time-out 15 minutes after
˚C
SAtion, 4if door is left open or display lighting is on, to prevent overheating.
each activa
WARMER
Adjust Temperature Set-Point
ON
OFF
To adjust temperature set-point, touch
keypad and ˚̊current set-point will be displayed.
F/C
SET
WARMER
ON
OFF
ON
OFF
Use the
˚̊F/C
SET
WARMER
or
COLDER
˚̊F/C
SET
LIGHT
COLDER
keypad activity occurs, or you may SA
exit “S4E˚CT” mode by pressing the
ON
OFF
LIGHT
WARMER
55
WARMER
Pressing the
SET
˚̊F/C
keypad will toggle the ˚dF isplay betw˚Ceen ˚FCahrenh˚Feit and Centigrade
LIGHT
temperatur˚eF display.
Black-Out Mode
38
13
55 SA 13 4 38
˚F
55
38
13
4 ˚C
tom˚Catically 38
shuts˚Foff when door is closSA
ed.
55D˚iFsplay au13
SA ˚C 4 ˚C
Display Lighting can be enabled with the door closed by pressing the
SA
4
keypad four (4) times.
˚F Press and˚Chold the
˚kFeypad while pressing the
55
38
13
COLDER
Sabbath Mode
ON
OFF
ON
SET
OFF
SET
COLDER
TruProtect™ System
Door Ajar Alarm
High/Low Temp Alarm
Power Failure Alarm
˚̊F/C
SET
LIGHT
COLDER
WARMER
SET
ON
OFF
COLDER
WARMER
˚̊F/C
˚̊F/C
LIGHT
˚̊F/C
LIGHT
keypad.
4
55
38
13
Note: Alarm may occur when changing set-points in excess of 10ºF, and/or high usage,
˚F
˚F ˚C
˚C ˚F
˚F
this is normal. 55
TruProtect m13
ust55
be Enab38
led13
, (See “Disa38
ble/Enable TruProtect”, described
below.)
SA
4 ˚C
Note: Alarm will occur upon initial installatio˚Cn, since unit wa˚Cs run at factory to verify
quality, this is normal. TruProSA
tect must be4ESA
nabled, (See4
“Disable/Enable TruProtect”,
Option avail55
able
˚F
keypad to reset all other alarms.
˚̊F/C
LIGHT
COLDER
Disable/Enable TruProtect™
Press and hold the
System.
ON
OFF
WARMER
SET
keypad for 5˚̊-seconds to “disable” or “enable” TruProtect™
F/C
LIGHT
55 ˚F
13 ˚C
38 ˚F
13 ˚C
LIGHT
ON
COLDER
4 ˚C
SA
SET
˚̊F/C
LIGHT
WARMER
COLDER
˚̊F/C
SET
LIGHT
Display will flash SA to 4confirm your selection, then unit will OFF
enter Sabbath Mode. The display, audible alarms, LED
COLDER
and lights will be disabledWARMER
. Sabbath Mode will automatically time-out in 36 hours, or can be exited by repeating the
enabON
le keypad SET
routine.
˚̊F/C
LIGHT
OFF
LED displays steady greenCOLDER
when TruProtect™ is enabled.
Audible alarm will sound 3-times every 30-seconds, LED will flash green.
Alarm will sound 6-times every minute and LED will flash red
outside acceptable limits.
if product temperature excursions occur for a duration
WARMER
LED will flash
ON
ambOFF
er
wheSET
never power is
55
˚F
55˚˚FF
˚F
ON
interrupted˚̊F/C
to uniOFF
t. NLIGHT
o audibSET
le signal.
13
COLDER
˚C
55
38
13˚C ˚C
WARMER
COLDER
13
˚̊F/C
38˚F ˚F
LIGHT
38
ON
OFF
55
LED displays steady green
F/C
SET
LIGHT
COLDER
13
38
˚C
when alarms enabled. LED displays steady amber
SA
4
55 ˚F
38 ˚F
˚C
4˚C ˚
Note that although pressing the
keypad will reset th˚̊ e alarms, the alarm will resume if the “alarm condition” still
C
exists.
˚F
˚C
˚F
SA
55 ˚F
˚̊F/C
Models only.
˚C
COLDER
16
ON
OFF
WARMER
WARMER
Close door to reset Door Ajar alarm. Press
ON
SET
F oor
oOFF
n ˚CGlas38
s ˚D
13
38 ˚F
13 ˚C
WARMER
WARMER
LIGHT
SET
LIGHT
In addition, the control panel is hidden when door is closed.
COLDER
ON
OFF
˚̊F/C
SET
COLDER
described below.)
Reset Alarms
55 ˚F
WARMER
ON
OFF
System monitoring is a˚Cutomatically enabled unless system has been disabled. (See
below.)
For Door Ajar Alarm, TruProtect must be Enabled, (See “Disable/Enable TruProtect”,
˚F
˚F
˚C
described below.)
SA
LIGHT
COLDER
SA SA 4 ˚C 4 ˚C
WARMER
F/C
˚̊SET
LIGHT
F
55 ˚F 55 ˚=
13 ˚C 13 ˚C 38 ˚F 38 ˚F
˚C
ON
OFF
ON
OFF
F/C
Temperature variation in “compartment air”, above and below set-point, is a normal effect of refrigeration system
cycling on and off. Stored items will not experience the full temperature swing of the compartment air due to the
dampening effect of their thermal mass.
WARMER
Display Lighting
keypad a sec˚̊ ond time.
keypads to adjust set-point temperature.
LIGHT
Display “Actual” Temperature Display represents “real-time” monitoring of the compartments stored wine and/or
contents. Some temperature flu˚cFtuation aro˚uCnd your des˚Fired set-point is normal.
ON
OFF
WARMER
SET
COLDER
COLDER
Select ºF or ºC Display
C
“Set” will appear in display 55 ˚F wh13e˚n
in 38
se˚Ft-point mode. “SET” mode will automatically time-out in 10 seconds if no
˚F
13 ˚C
˚C
4
SA
when disabled.
SA
4
˚C
38 ˚F
17
˚C
˚F˚F
˚C
˚F
SETTING THE CONTROLS - DUAL ZONE
55˚
The temperature of the wine cellar ranges from 40ºF (4ºC) to 65°F (18ºC).
TruProtect™ “Basic” Function “Quick” Reference
Solid Door Dual Zone Models:
64
Glass Door Dual Zone Models:
˚F
42
˚F
ON
64
Hi/Low Temp Upper
Hi/Low Temp Lower
˚F
42
˚F
ON
Hi/Low Temp Upper
Hi/Low Temp Lower
Place new control here when I get it from Ray
Function Access
Function
ON
OFF
Control Confirmation/Comment
Turn Unit On & Off
Pressing and holding the
Adjust Temperature Set-Point
To adjust temperature set-point, press the
key. When a compartment is in “SET”
mode, a “SET” icon will be displayed. Pressing either the
or
keys located
on the display pad will raise or lower the set temperature by one (1) °F or °C (depending
key for 5-seconds will turn the unit “ON” or “OFF”.
SET
WARMER
COLDER
Display will be blank when the refrigeration system is off. Lights will still function, but will time-out in 15 minutes after
each activation if door is left open or display lighting is on, to prevent overheating.
“SET” mode will automatically time-out in ten (10) seconds and default to actual content temperature if no keypad
activity occurs, or you may exit “SET” mode by pressing the
key until “SET” icon disappears.
SET
on your setting).
Temperature variation in “compartment” air, above and below set-point, is a normal effect of the refrigeration system
cycling on and off. Stored items will not experience the full temperature swing of the compartment air due to the
dampening effect of their thermal mass.
Display “Actual” Temperature
Display represents “real-time” temperature of each compartment’s stored wine and/or
contents. Some minor temperature fluctuation around your desired set-point is normal.
Select °F or °C Display
Pressing the ˚ key will toggle the display between Fahrenheit and Centigrade
temperature display.
Black-Out Mode
Display automatically shuts off when the door is closed.
Display Lighting
Display lighting can be enabled with the door closed by pressing the
Sabbath Mode
Press and hold the
TruProtect™ System
System monitoring is automatically enabled unless system has been shut off (see below).
TruProtect™ System message center displays a green “ON” when TruProtect™ is enabled and an amber “OFF” when
TruProtect™ is disabled.
Door Ajar Alarm
For Door Ajar Alarm, TruProtect must be Enabled, (See “Disable/Enable TruProtect”,
described below.)
NOTE: Alarm may occur when changing set-points in excess of 10ºF, and/or high usage,
this is normal. TruProtect must be Enabled, (See “Disable/Enable TruProtect”, described
below.)
NOTE: Alarm will occur upon initial installation, since unit was run at factory to verify
quality, this is normal. TruProtect must be Enabled, (See “Disable/Enable TruProtect”,
described below.)
Close door to reset “DOOR AJAR” Alarm. Press the
key to reset all other alarms.
An audible alarm will sound 3 times every 30 seconds and the message center will display an amber “DOOR AJAR”.
High/Low Temp Alarm
Power Failure Alarm
Reset Alarms
Disable/Enable TruProtect™
F/C
SET
key while pressing the
˚F/C
SET
=
13 ˚ C
In addition, the control panel is hidden when the door is closed.
LIGHT
key.
key four (4) times in seven (7) seconds.
ON
OFF
Press and hold the
System.
55 ˚ F
Display lighting stays on continuously.
The display will flash SA to confirm your selection, then the unit will enter Sabbath Mode. The display, audible alarms,
message center and lights will be disabled. Sabbath Mode will automatically time-out in 72 hours, or can be exited by
repeating the enabling process.
An audible alarm will sound 6 times every minute and the message center will display a red “HI/LOW TEMP UPPER” or
a red “HI/LOW TEMP LOWER” if product temperature excursions occur for a duration outside acceptable limits.
The message center will display an amber “POWER FAILURE” whenever power is interrupted to the unit. There is no
audible alarm with a power failure.
Although pressing the
ON
OFF
key resets the alarms, the alarm will resume if the “alarm condition” still exists.
key for five (5) seconds to enable or disable the TruProtect™
The message center displays a green “ON” when the alarms are enabled.
18
19
LOADING RECOMMENDATIONS - 15” W. Models
LOADING RECOMMENDATIONS - 24” W. Single Zone Models
Each of the six roll-out racks hold four bottles. The necks of the bottles alternate front to
back. To aid in loading/unloading, the racks extend up to 14 inches (35.6 cm) to allow
easier access to the rear bottles. Bottom racks may be removed for storing “jug’” wines.
Magnums and other large bottles may be stored by removing the rack directly above the
intended storage rack. To remove a rack, first unlock the rack by pushing the lock
backward. The lock is located on the bottom front of each rack. After reinserting the rack,
push the lock forward to lock the rack back into place.
Each of the top six roll-out racks holds 8 bottles with necks alternating front to back. The bottom wood cradle holds six
bottles for a total of 54 bottles. To aid in the loading and unloading, the racks extend up to 14 inches (35.6 cm) to allow
easier access to rear bottles. Tall bottles should not be loaded on the bottom rack because they may prevent the door
from closing. The bottom rack may be removed for storing “jug” wines. You may store magnum and other large bottles
on the upper right and left positions of the cabinet shelving or on any of the middle racks by removing the rack directly
above them. To remove a rack, first unlock the rack by pushing the lock backward. The lock is located on the bottom front
of each rack. After reinserting the rack, push the lock forward to lock the rack back into place. Position white wines on the
middle or lower racks and red wines on the upper racks.
Bottles on the top rack directly under the light will be exposed to slightly higher
temperature when the light is on. Store red wines on the upper racks where the
temperature is higher and white wines on the middle or lower racks where the
temperature is lower. REMEMBER TO TURN OFF THE LIGHT WHEN IT IS NO LONGER
NEEDED.
Bottles on the top rack directly under the light will be exposed to a slightly higher temperature when the light is on.
REMEMBER TO TURN OFF THE LIGHT WHEN IT IS NO LONGER NEEDED.
Roll-out Racks
Store wines intended for everyday use on the front half of the racks where labels are
completely visible and place wines for aging or long term storage in the rear half of the
rack. Pull wine racks out gently to minimize the unsettling of your wine collection.
Avoid pulling out more than one rack at any time to maintain stability.
Store wines intended for everyday use on the front half of the racks where labels are completely visible and place wines
for aging or long term storage in the rear half of the rack. Pull wine racks out gently to minimize the unsettling of your
wine collection. Avoid pulling out more than one rack at any time to maintain stability.
Rear Bottles
(Necks Facing Front)
Front Bottles
(Necks Facing Rear)
Front Bottles
(Necks Facing Rear)
Rear Bottles
(Necks Facing Front)
Since the bottles are not
stacked on top of each
other, the single bottle
roll-out rack allows easy
view and access of your
inventory without
disturbing other bottles.
Since the bottles are not
stacked on top of each
other, the single bottle rack
allows easy view and access
to your inventory without
disturbing other bottles
LOADING RECOMMENDATIONS - 24” W. Dual Zone Models
Both zones can be set for either temperature range, red or white, but for more efficient energy usage and functionality of
the unit, it is better to use the top compartment for reds (warmer) and the bottom compartment for whites (cooler).
LOADING RECOMMENDATIONS - 24” W. Models
Each of the top five roll-out racks holds 8 bottles with necks alternating front to back. The bottom shelf holds four bottles
for a total of 44 bottles. To aid in the loading and unloading, the racks extend up to 14 inches (35.6 cm) to allow easier
access to rear bottles. Tall bottles should not be loaded on the bottom rack because they may prevent the door from
closing. The bottom rack may be removed for storing “jug” wines. You may store magnum and other large bottles on the
upper right and left positions of the cabinet shelving or on any of the middle racks by removing the rack directly above
them. To remove a rack, first unlock the rack by pushing the lock backward. The lock is located on the bottom front of
each rack. After reinserting the rack, push the lock forward to lock the rack back into place. Position white wines on the
middle or lower racks and red wines on the upper racks.
Bottles on the top rack directly under the light will be exposed to a slightly higher temperature when the light is on.
REMEMBER TO TURN OFF THE LIGHT WHEN IT IS NO LONGER NEEDED.
Each of the top five roll-out racks holds 8 bottles with necks alternating front to back. The bottom shelf holds four bottles
for a total of 44 bottles. To aid in the loading and unloading, the racks extend up to 14 inches (35.6 cm) to allow easier
access to rear bottles. Tall bottles should not be loaded on the bottom rack because they may prevent the door from
closing. The bottom rack may be removed for storing “jug” wines. You may store magnum and other large bottles on the
upper right and left positions of the cabinet shelving or on any of the middle racks by removing the rack directly above
them. To remove a rack, first unload all wine bottles then pull the rack out and upward. Position white wines on the middle
or lower racks and red wines on the upper racks.
Bottles on the top rack directly under the light and on the rack directly below the separator shelf will be exposed to a
slightly higher temperature when the light is on. REMEMBER TO TURN OFF THE LIGHT WHEN IT IS NO LONGER
NEEDED.
Store wines intended for everyday use on the front half of the racks where labels are completely visible and place wines
for aging or long term storage in the rear half of the rack. Pull wine racks out gently to minimize the unsettling of your
wine collection. Avoid pulling out more than one rack at any time to maintain stability.
Store wines intended for everyday use on the front half of the racks where labels are completely visible and place wines
for aging or long term storage in the rear half of the rack. Pull wine racks out gently to minimize the unsettling of your
wine collection. Avoid pulling out more than one rack at any time to maintain stability.
20
21
CLEANING AND MAINTENANCE
Any piece of equipment works better and lasts longer when maintained properly and kept clean.
Condenser
The condenser underneath the cabinet does not require frequent cleaning; however, satisfactory cooling depends on
adequate ventilation over this heat exchanger. It is recommended to annually clean the condenser by vacuuming and
brushing. To access the condenser, the unit must be pulled out from the installation and the lower machine
compartment access cover removed.
WARNING
Disconnect the power cord before removing the access cover.
Be sure that nothing obstructs the required air flow openings in front of the cabinet. At least once or twice a year, brush
or vacuum lint and dirt from the front grille area.
Cabinet
The cabinet can be washed with mild soap and water and thoroughly rinsed with clear water. NEVER use abrasive
scouring powders.
Interior
Wash interior compartment with mild soap and water. DO NOT USE abrasive powder, solvent, polish cleaner or
undiluted detergent.
Stainless Steel Parts
All stainless steel parts should be wiped regularly with hot soapy water. Use a liquid cleaner designed for stainless steel
when soapy water will not do the job. DO NOT USE steel wool, abrasive cloths, cleansers, or powders. DO NOT
permit citrus or tomato juice to remain on stainless steel surfaces, as citric acid will permanently discolor stainless steel.
ENERGY SAVING TIPS
The following suggestions will minimize the cost of operating your refrigeration appliance.
1. Do not install your appliance next to a hot appliance, (cooker, dishwasher, etc.), heating air duct or other heat sources.
2. Install product out of direct sunlight.
3. Assure the toe grille vents at front of unit beneath door are not obstructed. Keep toe grille vents clean to allow
ventilation for the refrigeration system to expel heat.
4. Plug your appliance into a dedicated power circuit. (Not shared with other appliances.)
5. When initially loading your new product, or whenever large quantities of warm contents are placed within refrigerated
storage compartment, minimize door openings for the next 12 hours to allow contents to pull down to compartment
set- point temperature.
6. Maintaining a relatively full storage compartment will require less appliance run-time than an empty compartment.
7. Assure door closing is not obstructed by contents stored in your appliance.
8. Allow hot items to reach room temperature before placing in product.
9. Minimize door openings and duration of door openings.
10. Use the warmest temperature control set-point that meets your personal preference and provides the proper storage
for your stored contents.
11. For wine storage products:
a. When serving temperatures are not required, return the compartment(s) set-point to the ideal red and white
wine long term storage temperature of 13°C/55°F.
b. For Dual-Zone product with two (2) independent temperature controlled compartments, use the lower
compartment for the coldest storage/serving temperature, (i.e. - red wines on top, white wines in lower).
12. Minimize use of display lighting option on glass door products, (light stays on with door closed).
13. When on vacation or away from home for extended periods, set the appliance to warmest acceptable temperature for
the stored contents.
14. Set the control to the “OFF” position if cleaning the unit requires the door to be open for an extended period of time.
15. Annually clean condenser heat exchange coil located in machine compartment underneath unit, (see Cleaning and
Maintenance section).
TROUBLESHOOTING CHART
Brass Parts
CAUTION: All brass parts are coated with an epoxy coating. DO NOT USE BRASS OR ABRASIVE CLEANERS ON
THE BRASS PARTS. All brass parts should be wiped regularly with hot soapy water. When hot soapy water will not do
the job, use every day non-abrasive household cleaners.
Glass Door
Use a glass cleaner or mild soap and water with a soft cloth to clean the glass door. DO NOT USE any abrasive
powders. On full overlay models, use caution when cleaning near logo area.
Problem
Possible Cause
Solution
Odor in cabinet
Unit interior needs cleaning
Clean inside of unit
Noisy operation
Unit vibrates
Unit not level
Unit not level
Weak floor
LED light burned out
No power at outlet
Control panel tuned “OFF”
Adjust leveling legs
Adjust leveling legs
Rebuild floor or move to a different location
Replace LED light
Test outlet with lamp
Turn unit on with on/off pad on control panel
Power cord not plugged into power
source
House fuse blown
Prolonged door openings
Control panel set too cold
Condenser needs cleaning
Too many door openings
Prolonged door openings
Hot, humid weather increases
condensation
Plug unit into power source
Interior lighting not working
Appliance will not run
Painted Surfaces
Wash with warm soapy water. DO NOT USE steel wool, abrasive cleansers, ammonia, acids or commercial oven
cleaners which may damage the finish.
Appliance runs too long
Door Gasket
The vinyl gasket may be cleaned with mild soap and water, a baking soda and water solution, or a mild scouring
powder.
22
Moisture collects inside
of unit
Reset house fuse
Reduce number and/or duration of openings
Raise temperature of unit via control panel
Clean condenser
Reduce number of door openings
Reduce number of door openings
Move unit to cooler location
As humidity decreases, moisture will disappear
Moisture collects on outside Hot, humid weather increases
surface of unit
Control improperly set
Move unit to cooler location
Interior too hot/too cold
Control improperly set
Reset control to desired temperature
Faulty thermometer
Recheck with second thermometer
23
Reset to slightly warmer temperature
SERVICE DIAGNOSTICS - SINGLE ZONE
TruProtect™ “Advanced” Function “Quick” Reference
55˚
Solid Door Single Zone Models:
Glass Door Single Zone Models:
55 ˚F
ON
OFF
TruProtect System
WARMER
POWER FAILURE - Flashing Amber
F/C
SET
ALARMS OFF - Steady Amber
PRESS ON/OFF - Reset
PRESS AND HOLD
Function
ON
OFF
˚̊
Enable the Show Room Mode by pressing and holding the
keypad while
performing a “Power On Reset”, (POR), i.e. - disconnect and reconnect the power
supply to unit. Exit Show Room Mode by initiating a POR only.
F/C
SET
“Enter” and “Exit” Service Diagnostics mode by pressing and holding the
WARMER
while pressing the
COLDER
WARMER
˚̊F/C
COLDER
ON
OFF
LIGHT
WARMER
˚̊ ad.
feature. The 15-minute light-on time can be reactivated by closing and opening the door or by pressing the keyp
ON
OFF
55
˚F
13
keypad
“model specific” system components and sensors and change state of components where applicable, (i.e. - compressor
˚C
38
4
The microprocessor in the control continually monitors critical refrigeration system
˚F
˚C
˚F
˚F
˚C
components for proper operation. If component parameters exceed normal operating
13
WARMER
˚F
on/off, etc...). While in Service Diagnostics Mode, tests are incremented by pressing the
ON
OFF
WARMER
ON
OFF
Service Diagnostics
E1
Compressor fault, (high/low amps).
E2
Condenser fan motor fault, (high/low amps).
E3
Evaporator thermistor “sensor B” fault, (out-of-range).
E1
Display thermistor “sensor A” fault, (out-of-range).
following component tests are available:
Test #
˚F
4 ˚C
SA
4
˚C
38
specifications, the display will automatically flash the respective error code as follows:
˚C
SA
Power line fluctuations may cause an error code to be displayed with no product fault.
WARMER
ON
OFF
Therefore, the first time an error code appears, please clear the code by holding
SET
and
WARMER
pressing
ON
OFF
˚̊F/C
ON
OFF
SET
Component Description
OK
0
Temp Sensor A
0-
1
Temp Sensor B
1-
2
Compressor
3
Interior/Ice Maker Fan
4
Reverse Gas Solenoid
n/a
5
Condenser Fan
n/a
6
Mullion Heater
n/a
7
Door A Sense
n/a
8
Door B Sense
n/a
9
Door C Sense
n/a
55
Note: Must use magnet to change state of Door C Sense.
LIGHT
COLDER
F/C
magnet sense area
LIGHT
COLDER
should contact your Dealer or Viking Customer Service to schedule service by a
ON
OFF
qualified technician.
55˚F
40 ˚F
SET
PRESS AND HOLD
13˚C
38˚F
SA
4˚C
24
55˚F
13˚C
38˚F
SA
4˚C
˚̊F/C
SET
WARMER
and
SET
COLDER
keypad and ˚̊specific
F/C
LIGHT
COLDER
LIGHT
keypads respectively. The
˚F
˚C
55
13
Available Status Indicators
˚̊F/C
LIGHT
COLDER
4 times. If the prod˚̊ uct is at fault, the error code will appear again, and you
SET
LIGHT
Service Diagnostics Mode enables service technicians to identify the firmware and software versions, test status of
LIGHT
SA
55
F/C
SET
COLDER
˚̊F/C
SET
Display Error Code Reference:
38
ALARMS OFF - Steady Amber
PRESS ON/OFF - Reset
component state can be changed to “on” and “off” by pressing the
13
HIGH/LOW TEMP - Red
panel to function. Lights will time out after 15-minutes of continuous on-time while in Show Room Mode as a safety
keypad 4-times within 5-seconds. Service Diagnostics mode
also will automatically exit after 5-minutes of no keypad entry.
55
LIGHT
Show Room Mode will disable the refrigerator system and fans while allowing the internal lights, display and user interface
LIGHT
COLDER
SET
COLDER
SET
TruProtect System
POWER FAILURE - Flashing Amber
Control Confirmation/Comment
Function Access
ON
OFF
˚̊F/C
PRESS AND HOLD
WARMER
Show Room Mode
55 ˚F
ON
OFF
HIGH/LOW TEMP - Red
COLDER
WARMER
25
n/a
˚F
n/a
Off/Open
˚F
55 ˚
13 C
SA
00
1 0 55 ˚F
˚C
13
20
˚F
338
0
SA
4 0 ˚C
4
50
60
70
80
90
38 ˚F
On/Shorted
SA
38
4
˚C
13
˚F
SA
˚C
01
11
21
31
41
51
61
71
81
91
38 ˚F
4 ˚C
4 ˚C
SERVICE DIAGNOSTICS - DUAL ZONE
TruProtect™ “Advanced” Function “Quick” Reference
Solid Door Dual Zone Models:
Glass Door Dual Zone Models:
64
˚F
42
˚F
ON
64
Hi/Low Temp Upper
Hi/Low Temp Lower
˚F
42
˚F
ON
Hi/Low Temp Upper
Hi/Low Temp Lower
Place new control here when I get it from Ray
Function
Function Access
Control Confirmation/Comment
To “Enter” and “Exit” Service Diagnostics mode, press and hold the
WARMER
ON
OFF
˚̊F/C
SET
pressing the
COLDER
ON
OFF
LIGHT
WARMER
keypad while
˚̊F/C
SET
Service Diagnostics Mode enables service technicians to identify the firmware and software versions, test status of
LIGHT
keypad four (4) times in five (5) seconds. Service Diagnostics mode
COLDER
“model specific” system components and sensors and change state of components where applicable, (i.e. - compressor
WARMER
will automatically exit after five (5) minutes of no keypad entry.
on/off, etc...). While in Service Diagnostics Mode, tests are incremented by pressing the
ON
OFF
WARMER
ON
OFF
component states can be changed to “ON” and “OFF” by pressing the
Display Error Code Reference:
following component tests are available:
ON
OFF
55
4 ˚C
SA
Test #
38
13
0
4 ˚C
SA
Compressor Error, (High/Low Amps)
E1
Service Diagnostics
55
38
13
Condenser Fan Error, (High/Low Amps)
E2
E3
Upper Compartment “Sensor A” Error, (Out-of-Range)
E1
Lower Compartment “Sensor B” Error, (Out-of-Range)
Power line fluctuations may cause an error code to be displayed with no product fault.
WARMER
ON
OFF
Therefore, the first time an error code appears, please clear the code by holding
SET
and
WARMER
pressing
ON
OFF
˚̊F/C
COLDER
4 times. If the prod˚̊ uct is at fault, the error code will appear again, and you
F/C
SET
OK
Off/Open
Temp Sensor, Upper
0-
00
4˚C
26
˚C
˚F
13
38
SA˚C
4
1-
2
Compressor
n/a˚F
3
Condenser Fan
n/a
4
Compartment Fan, Upper
n/a
5
Compartment Fan, Lower
n/a
50
51
6
Heater/Fan Assembly, Upper
n/a
60
61
7
Heater/Fan Assembly, Lower
n/a
70
71
8
Door Sense
n/a
80
81
55
˚F
55 ˚
13 C
13 ˚
38 F
3 0 SA
SA 4 0 4 ˚C
20
11
21
31
38 ˚F
4 ˚C
41
NOTE: The Door Sense is located between the Upper Compartment display and the ON/OFF key and can be tested
with any magnet.
magnet sense area
ON
OFF
SA
01
˚F
˚C
Temp Sensor, Lower
LIGHT
qualified technician.
38˚F
1 0 55
On/Shorted
1
LIGHT
13˚C
LIGHT
COLDER
should contact your Dealer or Viking Customer Service to schedule service by a
55˚F
LIGHT
keypads respectively. The
COLDER
˚̊F/C
Component Description
COLDER
55˚F
F/C
COLDER
LIGHT
Available Status Indicators
The microprocessor in the control continually monitors critical refrigeration system
compo˚Fnents for pr˚o
˚Cl operating ˚F
C per operati˚oFn. If component parameters ex˚Fceed norma
specifications, the display will automatically flash the respective error code as follows:
and
WARMER
keypad and ˚̊specific
˚̊F/C
SET
SET
SET
13˚C
38˚F
SA
4˚C
40 ˚F
SET
PRESS AND HOLD
27
SERVICE INFORMATION
If service is required, call your dealer or authorized service agency. The name of the authorized service agency can be
obtained from the dealer or distributor in your area.
Have the following information readily available.
• Model number
• Serial number
• Date purchased
• Name of dealer from whom purchased
TWO YEAR FULL WARRANTY
Built-In/Freestanding Undercounter Wine Cellars and all of their components and accessories, except as detailed below*, are warranted to be free from defects in
material or workmanship under normal household use for a period of two (2) years from the date of original retail purchase. Viking Range Corporation, warrantor,
agrees to repair or replace, at its option, any part which fails or is found to be defective during the warranty period
Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency,
or if you continue to have service problems, contact Viking Range Corporation at 1-888-VIKING1 (845-4641), or write to:
VIKING RANGE CORPORATION
PREFERRED SERVICE
1803 Hwy 82W
Greenwood, Mississippi 38930 USA
Record the information indicated below. You will need it if service is ever required. The model and serial number for
your wine cellar are located on the front of the unit at the base of the door frame.
Model Number
Date of Purchase
UNDERCOUNTER/FREESTANDING WINE CELLAR WARRANTY
(Units Certified for Indoor Use)
*Painted and decorative items are warranted to be free from defective materials or workmanship for a period of ninety (90) days from the date of original retail
purchase. ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.
SIX YEAR FULL WARRANTY
Any sealed refrigeration system component, as listed below, is warranted to be free from defective materials or workmanship in normal household use during the third
through the sixth year from the date of original retail purchase. Viking Range Corporation, warrantor, agrees to repair or replace, at its option, any part which fails or is
found to be defective during the warranty period.
Sealed Refrigeration System Components:
Compressor, Evaporator,
Condenser, Connecting Tubing, Dryer/Strainer
TWELVE YEAR LIMITED WARRANTY
Serial Number
Any sealed refrigeration system component, as listed above, which fails due to defective materials or workmanship in normal household use during the seventh
through the twelfth year from the date of original retail purchase will be repaired or replaced, free of charge for the part itself, with the owner paying all other costs,
including labor.
Date Installed
NINETY (90) DAY RESIDENTIAL PLUS WARRANTY This warranty applies to applications where use of the product extends beyond normal residential use.
Examples are, but not limited to, bed and breakfasts, fire stations, private clubs, churches, etc. This warranty excludes all commercial locations such as
restaurants, food service locations and institutional food service locations.
This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty.
Dealer’s Name
Address
This warranty shall apply to products purchased and located in the United States and Canada. Products must be purchased in the country where service is requested.
Warranty labor shall be performed by an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting from
abuse, accident, natural disaster, loss of electrical power to the product for any reason, alteration, improper installation, improper operation or repair or service to the
product by anyone other than an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting from indoor
units being used in outdoor situations. This warranty does not apply to commercial usage. Warrantor is not responsible for consequential or incidental damage
whether arising out of breach of warranty, breach of contract, or otherwise. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
If service requires installation of parts, use only authorized parts to insure protection under the warranty.
Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof of purchase upon request, and making the appliance
reasonably accessible for service. If the product or one of its component parts contains a defect or malfunction during the warranty period, after a reasonable number
of attempts by the warrantor to remedy the defects or malfunctions, the owner is entitled to either a refund or replacement of the product or its component part or
parts. Replacement of a component part includes its free installation. Warrantor’s liability on any claim of any kind, with respect to the goods or services covered
hereunder, shall in no case exceed the price of the goods or service or part there of which gives rise to the claim.
KEEP THIS MANUAL FOR FUTURE REFERENCE.
WARRANTY SERVICE: Under the terms of this warranty, service must be performed by a factory authorized Viking Range Corporation service agent or representative.
Service will be provided during normal business hours, and labor performed at overtime or premium rates shall not be covered by this warranty. To obtain warranty
service, contact the dealer from whom the product was purchased, an authorized Viking Range Corporation service agent, or Viking Range Corporation. Provide
model and serial number and date of original purchase. For the name of your nearest authorized Viking Range Corporation service agency, call the dealer from whom
the product was purchased or Viking Range Corporation. IMPORTANT: Retain proof of original purchase to establish warranty period.
The return of the Owner Registration Card is not a condition of warranty coverage. You, however, should return the Owner Registration Card so that Viking Range
Corporation can contact you should any question of safety arise which could affect you.
Any implied warranties of merchantability and fitness applicable to the above described undercounter wine cellar are limited in duration to the period of coverage of
the applicable express written limited warranties set forth above. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. This warranty gives you specific rights, and you may also have other rights which may vary from jurisdiction to jurisdiction.
Specifications subject to change without notice.
28
29
UNDERCOUNTER/FREESTANDING WINE CELLAR WARRANTY
(Units Certified for Outdoor Use)
ONE YEAR FULL WARRANTY
Built-In/Freestanding Undercounter Wine Cellars and all of their components and accessories, except as detailed below*, are warranted to be free from defects in material or
workmanship under normal household use for a period of one (1) year from the date of original retail purchase. Viking Range Corporation, warrantor, agrees to repair or
replace, at its option, any part which fails or is found to be defective during the warranty period.
*Painted and decorative items are warranted to be free from defective materials or workmanship for a period of ninety (90) days from the date of original retail purchase.
ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.
FIVE YEAR LIMITED WARRANTY
Any sealed refrigeration system component, as listed below, is warranted to be free from defective materials or workmanship in normal household use during the second
through the fifth year from the date of original retail purchase. Viking Range Corporation, warrantor, agrees to repair or replace, at its option, any part which fails or is found
to be defective during the warranty period.
Sealed Refrigeration System Components:
Compressor, Evaporator, Condenser, Connecting Tubing, Dryer/Strainer
It is recommended that in temperatures above 100oF (37.8oC) and below 40oF (4.4oC) the unit be shut off. The normal operating range for the unit is between 60oF (15.6oF)
and 100oF (37.8oC).
NINETY (90) DAY RESIDENTIAL PLUS WARRANTY This warranty applies to applications where use of the product extends beyond normal residential use.
Examples are, but not limited to, bed and breakfasts, fire stations, private clubs, churches, etc. This warranty excludes all commercial locations such as restaurants,
food service locations and institutional food service locations.
This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty.
This warranty shall apply to products purchased and located in the United States and Canada. Products must be purchased in the country where service is requested.
Warranty labor shall be performed by an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting from abuse,
accident, natural disaster, loss of electrical power to the product for any reason, alteration, improper installation, improper operation or repair or service to the product by
anyone other than an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting from indoor units being used in
outdoor situations. This warranty does not apply to commercial usage. Warrantor is not responsible for consequential or incidental damage whether arising out of breach
of warranty, breach of contract, or otherwise. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof of purchase upon request, and making the appliance reasonably
accessible for service. If the product or one of its component parts contains a defect or malfunction during the warranty period, after a reasonable number of attempts by
the warrantor to remedy the defects or malfunctions, the owner is entitled to either a refund or replacement of the product or its component part or parts. Replacement of a
component part includes its free installation. Warrantor’s liability on any claim of any kind, with respect to the goods or services covered hereunder, shall in no case exceed
the price of the goods or service or part there of which gives rise to the claim.
WARRANTY SERVICE: Under the terms of this warranty, service must be performed by a factory authorized Viking Range Corporation service agent or representative.
Service will be provided during normal business hours, and labor performed at overtime or premium rates shall not be covered by this warranty. To obtain warranty service,
contact the dealer from whom the product was purchased, an authorized Viking Range Corporation service agent, or Viking Range Corporation. Provide model and serial
number and date of original purchase. For the name of your nearest authorized Viking Range Corporation service agency, call the dealer from whom the product was
purchased or Viking Range Corporation. IMPORTANT: Retain proof of original purchase to establish warranty period.
The return of the Owner Registration Card is not a condition of warranty coverage. You, however, should return the Owner Registration Card so that Viking Range
Corporation can contact you should any question of safety arise which could affect you.
Any implied warranties of merchantability and fitness applicable to the above described undercounter refrigerated beverage center are limited in duration to the period of
coverage of the applicable express written limited warranties set forth above. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. This warranty gives you specific rights, and you may also have other rights which may vary from jurisdiction to jurisdiction.
Specifications subject to change without notice.
30
31
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement