Perlick Refrigeration HP24 Operating instructions

Perlick Refrigeration HP24 Operating instructions
24” Signature Series Operation / Installation Manual
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Warranty Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
General Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Preparing the Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Preparing Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Unpacking and Moving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Anti-Tip Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Shelving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Door Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wood Overlay Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Wooden Wine Rack Trim Finishing . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Interior Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Loading Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Temperature Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Adjusting the Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Checking Product Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 10
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Cleaning the Condenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Introduction
Warranty Registration
Congratulations on your purchase of a Perlick residential
refrigeration product. Celebrating over 91 years of excellence,
Perlick is the industry leader in commercial refrigeration
systems. Today, Perlick has taken its expertise and experience into creating the highest quality and most innovative
residential products on the market. Perlick’s product offering
gives you the opportunity to enjoy the functionality and user
friendliness in just about any room of your home, including
kitchens, bedrooms, entertainment rooms, basements and
even bathrooms. All Perlick products are built with commercial-grade stainless steel — providing you with the beauty
and durability for a lifetime of use.
To request information or service, the model number and
serial number must be provided. This information is located
on the inside ceiling of the unit and on the warranty registration card included with information packet shipped with the
unit.
This Installation and Operation manual will answer your questions about the features, operation and maintenance of your
Perlick unit. If you have questions that are not addressed here,
call 800/558-5592.
IMPORTANT: Please read all instructions completely before
attempting to install or operate the unit. Take note of DANGER,
CAUTION and WARNING when they appear in the manual.
This information is important for the safe and efficient installation, operation and care of your Perlick unit.
DANGER indicates a hazard that will result in serious injury or
death if precautions are not followed.
WARNING indicates a hazard may cause serious injury or
death if precautions are not followed.
IMPORTANT: Read through the included warranty statement
then complete and mail the Warranty Registration Card as
soon as possible to validate the registration date. Warranty
registration can also be done online at www.perlick.com. If
warranty registration is not completed, Perlick will use the
date of sale as the first date of warranty for the unit. Please
record the purchase date of the unit and the dealer’s name,
address and telephone number below.
Model Number_____________________________________
Serial Number_____________________________________
Purchase Date_____________________________________
Dealer Name _____________________________________
Dealer Address_____________________________________
Dealer Phone No.____________________________________
Retain this manual along with the sales receipt for future
reference.
CAUTION indicates a hazard where minor injury or product
© 2009
24” Signature Series Operation / Installation Manual
General Precautions
DANGER
Risk of child entrapment. Before you throw away your old
refrigerator or freezer, take off the doors and leave shelves in
place so children may not easily climb inside.
Danger
Altering or cutting of the power cord, or removal of the power
plug, or direct wiring can cause serious injury, fire and/or loss
of property and/or life and will void the warranty.
caution
•Do not lift unit by door handle.
•Failure to clean the condenser every three months can cause
the unit to malfunction. This could void the warranty.
•Never install the unit behind closed doors. Be sure front
louvered toe plate is free of obstruction. Obstructing free
air flow can cause unit to malfunction and may void the
warranty.
Warning
•Never attempt to repair or perform maintenance on the
unit until the electricity has been disconnected.
•The anti-tip kit must be installed on this unit before it is
used. Never use the drawers, shelves or doors as steps or
to support more than they are designed to support.
caution
Use only Perlick replacement parts. Imitation parts can damage the unit, and may void the warranty.
Installation Specifications
•Never attempt to move unit without the aid of at least one
other person.
General
• All electrical instructions assume that outlet is located 410 inches from the floor.
•Floor must be level in area of installation. Leg levelers are
used for fine-tune adjustment only and should not be
used to compensate for floor differences exceeding 1/2”.
• When moving unit into position, take care to protect floor
surface with cardboard, rugs, etc.
• Always secure door shut prior to moving the unit.
Finished Rough Opening Requirements
• Height:
34-1/2” minimum
35-1/2” maximum
•Depth:
24”
• Width:
24”
© 2009
24” Signature Series Operation / Installation Manual
13 1/16” distance
same on both sides of cabinet
50” area in which
electrical outlet must be located
4 1/2” min.
clearance to side wall
on corner installation
98° min. door swing
for pull-out shelf
clearance
24 25/32” door swing clearance
25 27/64”
23 15/16”
22 1/8”
23 7/8”
34 5/16””
3 39/64”
1 53/64”
Figure 1. Dimensions
© 2009
24” Signature Series Operation / Installation Manual
pREPARING THE sPACE
Make sure the installation opening is properly prepared. Refer
to Figure 1 for space dimensions.
Caution
Do not cut cardboard sleeve covering the unit. Cutting may
result in damage to the exterior of the unit.
CAUTION
If unit is to be installed under a countertop, it is recommended that the countertop be supported by a structure other
than the unit itself, to prevent damage to the countertop.
1.Uncrate the unit outside on a flat level surface. Remove
the cardboard sleeve by removing the banding holding
the sleeve to the shipping base. Carefully lift the cardboard sleeve up over the top of the cabinet.
IMPORTANT: For a cabinet door to operate properly, the door
must open a minimum of 98° (see Figure 1). Use a minimum
4-1/2” filler in corner installations to ensure a 100° opening.
Allow 25” clearance in front of the unit for full door swing and
shelf pull-out.
2.Carefully lift unit off base and onto a hand truck or dolly
(this should be done with a minimum of two people,
larger cabinets may require additional helpers). Make sure
unit is balanced on transporting device. Secure unit to
transporting device using soft, flexible strapping. Protect
cabinet surfaces with cloth material where strapping contacts the unit.
IMPORTANT: Make sure floor under unit is level with the surrounding finished floor. Protect a finished floor with plywood,
cardboard or some other suitable material before moving the
unit into place. Failure to do this may result in damage to the
floor.
Preparing Electrical Connections
A 115 volt, 60Hz, 15 amp circuit breaker and electrical supply are required. A separate circuit is recommended for each
Perlick unit installed.
Follow the National Electrical Code along with local codes
and ordinances when installing the receptacle.
All Perlick units come equipped with a NEMA 5-15P, 90° plug
with a 5’ cord (minimum) extending beyond the rear of the
unit. The electrical outlet must be flush with, or recessed into,
the back wall.
Danger
Electrocution hazard!
Electrical grounding required. This appliance is equipped
with a 3-prong (grounding) polarized plug for protection
against possible shock hazards.
3.Before moving unit, secure door to unit with tape to hold
the door closed.
Warning
A minimum of two people should lift the cabinet off the base
to prevent possible personal injury.
4.Carefully move unit to installation site and place in front
of opening.
Anti-tip Brackets
WArning
Unit may tip forward if loaded racks/shelves are all pulled
out at the same time. To prevent tipping and provide a stable
installation, the unit must be secured in place with the antitip brackets provided with the unit.
A set of metal anti-tip brackets and #10 x 3/4” screws are
•Never remove the round grounding prong from the plug.
•Never use a 2-prong grounding adapter.
•Never use an extension cord to connect power to the
unit.
If a 2-prong wall receptacle is encountered, or a longer power
cord is required, contact a qualified electrician to install the
proper 3-prong receptacle in accordance with applicable
electrical codes.
Danger
Failure to comply with the above electrical guidelines may
result in possible injury/death/fire or loss of property.
Unpacking and Moving the Unit
Figure 2. Anti-Tip-Over Mounting
© 2009
24” Signature Series Operation / Installation Manual
supplied with the unit. The anti-tip brackets, when properly
installed, should secure the rear legs and prevent the unit
from tipping forward.
Some installation sites may require modification to provide a
secure surface for attaching the brackets. Refer to Figure 2 for
mounting bracket locations.
IMPORTANT: If installing on a concrete floor, concrete fasteners are required and are not included in the Anti-Tip kit.
Installation
Caution
Finished flooring should be protected with appropriate material to avoid damage from moving the unit.
If unit has been laid on its back or sides, place unit upright
and allow minimum of 24 hours before connecting power.
1. Plug the unit into the 15 amp grounded outlet located in
the installation opening. With power applied to the unit,
check that lighting and cooling function operate properly, then turn off power to the wall outlet at the circuit
breaker.
Warning
Shut off power to the wall outlet before installing unit into
the opening.
2.Check that the following are level and square:
- front face and interior opening
- installation opening and floor surface
- countertop bottom front edge
Figure 3. Leveling
IMPORTANT: The floor under the unit must be at the same
level as the surrounding finished floor.
flush with the surrounding cabinetry, or until the rear legs
are tight against the anti-tip brackets.
3. If all surfaces are level, refer to Figure 3 and perform the
following:
IMPORTANT: The rear leveling legs must be engaged under
the anti-tip brackets.
a. Measure from the floor to the bottom of the front
edge of the countertop.
b.Measure the rear of unit cabinet from floor to top of
cabinet, at back corners.
c. Adjust rear legs so B measurement equals A measurement. Using an adjustable wrench or pliers, turn legs
counterclockwise to raise the unit or clockwise to
lower the unit.
IMPORTANT: Leveling legs should not extend more than 3/4”
from bottom of unit.
4. Slide the unit into position. Make sure the rear levelling
legs slide under the anit-tip brackets. Push the unit into
the opening until the bottomfront edge of the unit is
© 2009
5. Shim the front of the unit so the front face is flush with the
surrounding cabinetry. Adjust the front legs to support
the countertop at the shimmed height. Using an adjustable wrench or pliers, turn legs counterclockwise to raise
the unit or clockwise to lower the unit. Countertop should
be resting on top of the unit.
IMPORTANT: If countertop is not resting entirely unit top,
shim the countertop to prevent damage to the countertop.
Caution
To prevent damage to the countertop and unit underneath,
do not place heavy objects on countertop directly above the
unit.
6.Check interior door openings inside unit and ensure unit
is level.
24” Signature Series Operation / Installation Manual
Caution
The louvered toe plate must be removed to service the unit.
The floor cannot interfere with removal. The louvered sections must not be covered or obstructed to prevent proper
air circulation.
Shelving
IMPORTANT: To achieve maximum performance, interior louver openings and fan guard openings should never be
obstructed.
Freezer/Refrigerator
The single door unit comes standard with black vinyl coated
adjustable full extension pullout shelves.
Wine Reserve
The single door unit comes standard with six full extension
black vinyl coated wine racks capable of storing 48 total wine
bottles. Shelves are removable and adjustable to accommodate oversized (magnum) bottles. Additional storage is available on the lower step for of an five wine bottles.
Beverage Center
The single door unit comes standard with two full extension
black vinyl coated wine racks and one industry exclusive full
extension pullout shelf allowing for storage of both wine and
beverages. Shelving positions are adjustable.
Adjusting Full Extension Shelving
1. Pull the shelf out to its farthest position. Locate the tabs
in the middle of both extenders (Figure 4). Lift one tab up
while pushing the opposite tab down and pull shelf out.
Lift one tab up while pushing the
opposite tab down and pull shelf out
Figure 4. Sliding Shelf Extender Tabs
To remove brackets,
remove shelf, lift front
of bracket to disengage
the front key slot, and
pull forward to disengage
the rear key slot.
2.Reposition each bracket separately. Grasp the middle of
the bracket, pull the front end up and out, then forward
to remove (Figure 5).
3. Place bracket at the desired position. Push the rear hook
into the rear key slot. Set front of bracket on the wall
hook.
4.Repeat for other bracket(s).
5. Push extenders completely into the unit. Align the shelf
grooves with the extenders and slide completely into the
unit.
Figure 5. Sliding Shelf Mounting Brackets
netry and door handles. The panel and door handles are supplied by the customer.
Door Options
All Perlick units accept any of the above door configurations
and are fully interchangeable.
Perlick residential units offer a variety of door panel design
alternatives; solid stainless steel, solid wood overlay, stainless
steel glass and wood overlay glass.
IMPORTANT: Glass with stainless trim and glass with wood
trim may sweat in conditions with relative humidity over
75%.
Solid stainless steel and stainless steel glass doors are shipped
from the factory with decorative stainless steel panels and
handles in place on the appliance.
Before beginning installation, check all components for proper fit and finish.
Solid wood overlay and glass wood overlay doors are designed
to accept a decorative front panel to match surrounding cabi-
Warning
• All overlay doors required a trim panel at least 3/4” thick.
Wood Overlay Installation
© 2009
24” Signature Series Operation / Installation Manual
•The solid wood overlay panel should not weigh more
than 20 pounds.
•The glass wood overlay panel should not weigh more
than 10 pounds.
The following instructions cover installing a solid wood
overlay or glass wood overlay panel and handle to a door or
drawer.
Mounting bracket
Nut
Lock strike
Lockwasher
Lock body
IMPORTANT: Contact the factory for full size wood overlay
panel layouts.
Screw
Lock bracket
Refer to Figure 7 for solid wood overlay panel.
Refer to Figure 8 for glass wood overlay panel.
Refer to Figure 9 for drawer wood overlay panel
Door Lock Installation (optional)
When installing to wood overlay, perform lock installation
before mounting wood overlay to door.
1. See Figure 6. Attach mounting bracket to wood overlay.
2. Insert lock body and attach with nut.
Figure 6. Door Lock - Optional
Handle Installation
Caution
Handle mounting on wood overlay door should be mounted
on overlay panel only (not the door) to avoid damage to the
factory door.
overlay onto door. Mark rear of wood overlay panel with
handle fastening locations.
2.Drill through wood overlay panel at marked locations tak-
1. Handle must be attached to overlay before mounting
22 3/16”
22 23/323”
/32”
27
13 9/32” 10 9/32”
19 57/64”
3 11/16”
1
0”
/32”
17
Ø /4”
Thru
3
0”
/64”
13
Ø 1/8”
/2” Deep
/32”
27
3 11/16”
1 25/32”
3
/64”
R 1 11/16”
2 1/8”
/16”
13
2”
1 1/16"
3 7/32”
13 39/64”
/64”
27
1 13/64”
A
29 13/16”
These (2) holes not to
be drilled for a door with lock
Detail A
Scale 1:2
All features called out
in this detail view apply
only to panels being
used on locking doors
15 7/64”
Locking door
only
16 39/64”
/ 4”
3
Rear View
26 35/64”
29 3/8”
/64”
22 /16”
13
/64”
19
3
0 11/32”
15
/64”
11
/64”
27
/32” Deep hole drilled at both ends
19
/32”
/16”
7
Figure 7. Solid Wood Overlay Panel
© 2009
24” Signature Series Operation / Installation Manual
22 23/32” 22 3/16”
23 /16”
9
19 57/64”
13 9/32”
10 9/32”
2 15/64”
3 11/16”
1 25/32”
/32”
27
1
0”
/32”
2 15/64”
/64”
3 11/16”
R 1 11/16”
11
2 1/8”
Ø 1/8”
1
/2” Deep
19 7/64”
18”
1 25/32”
3
/64”
/32”
17
Ø 3/4”
Thru
0”
27
13
Ø 1/8”
/2” Deep
/16”
13
2”
27
/64”
/64”
1 1/16"
19
3 7/32”
13 39/64”
These (2) holes
not to be drilled
24 43/64”
for a door with lock
25 49/64”
B
15 7/64”
On locking
doors only
D
Detail C
Scale 1:2
B
16 39/64”
Rear view
/64”
27
1 13/64”
C
3
All features called out
in detail views B-B & C apply
only to panels being used
on locking doors
D
/32”
/4” Hole detailed in view C
R 29/64”
Section B-B
26 35/64"
/64”
13
/64”
19
/16”
7
Front
29 3/8”
30 15/64”
Ø 11/32” 15/32”deep
Hole drilled at both ends
/8 ”
7
3
/16”
11
Rear
Section D-D
Scale 1:2
/4”
Figure 8. Glass Wood Overlay Panel
22 23/32” 19 57/64”
13 9/32”
10 9/32”
3 11/16”
27
/32” 0
3
C
/4 ”
0
27
/32”
3 11/16”
Rear View
6 1/64”
15 1/32”
9 1/64”
B
11 23/64”
14 3/16”
23 9/16”
Figure 9. Drawer Solid Wood Overlay
© 2009
24” Signature Series Operation / Installation Manual
Wooden Wine Rack Trim Finishing
All wine racks come with a stainless steel face, which can
be removed and replaced with wood faces to match the
surrounding cabinetry. See Figure 10.
The optional unfinished faces can be finished and sealed. In
many cases, stains and/or finishes have odors that may be
objectionable in an enclosed area. To remove the front wood
face from the wine shelf, simply pull out the wine shelf and
remove the fasteners. Finish as desired and re-install with
original fasteners.
Operation
General
The unit is equipped with a state-of-the-art refrigeration system. The variable speed compressor automatically changes
speeds based on system conditions and load. The cabinet is
equipped with an adjustable digital temperature controller
and LED display.
The unit is a frost-free model. The evaporator coil automatically defrosts on demand at predetermined intervals.
Interior Light
The unit is equipped with an interior light that illuminates
when the door is opened. A manual switch is located near the
light for displaying the product through a glass door. Always
ensure the manual switch is in the off position before closing
a solid wood or stainless steel door. If manual switch is left on
for an extended period of time, it may increase the cabinet
1
Loading Product
IMPORTANT: Before storing perishables, allow unit to run for
a minimum of 24 hours to allow temperature stabilization
after start-up.
When loading items into unit, do not block internal louvers
and fan guard openings or performance will be decreased.
Temperature Control Panel
The controller is located
inside
of
the
unit.
The display will read OFF when unit is off, and will show the
temperature when unit is on.
IMPORTANT: The LED display reads actual air temperature,
not product temperature. The following swings in temperature do not affect the actual product temperature:
Freezer:10°F swing
Refrigerator & Beverage Center:
6°F swing
Wine Reserve:
4°F swing
/8” x 0.312” deep
/8”
5
7 1/4”
8”
5
temperature, especially at the top and cause the refrigeration
system to run longer.
1 17/32”
/16”
1 1/2”
1
/2”
/16” to 1/8”
radius all
outside edges
1
18 5/16”
Figure 10. Wooden Wine Rack Trim
© 2009
24” Signature Series Operation / Installation Manual
The control comes preset for the following product
temperatures:
Freezer: Refrigerator: Beverage Center:
Wine Reserve:
-3°F
38°F
44°F
45°F
•Door gasket and sealing
• Amount of time internal light is illuminated
• Installation in direct sunlight or near a heat source
Maintenance
Adjusting the Setpoint
The setpoint is the desired temperature to be maintained in
the unit.
To adjust the setpoint:
1. Press the SET button located on the control panel (Figure
11).
2. Press the UP or DOWN arrow keys to the desired temperature. The controller will memorize the new setpoint.
IMPORTANT: The controllers have been programmed to only
allow a temperature adjustment within the following specific
ranges:
Freezer:
Adjustable Range:
-10°F to 10°F
Refrigerator:
Adjustable Range:
33°F to 43°F
Wine Reserve:
Adjustable Range:
44°F to 68°F
Beverage Center:
Adjustable Range:
37°F to 48°F
Checking Product Temperature
To accurately check the temperature of the product stored in
a refrigerated compartment, insert an accurate thermometer
into a sealable plastic (non-breakable) bottle, partially filled
with water. Tighten the cap securely.
Place the bottle into the desired area for 24 hours. Refrain
from opening the unit during testing period. After 24 hours,
check the temperature of the water. Adjust the control settings if necessary and re-test.
Warning
Shut off the electricity to the unit before cleaning the condenser and other routing maintenance.
Cleaning
To clean stainless steel exterior or interior surfaces, use a
soft, non-abrasive stainless steel cleaner to wipe down the
surfaces.
Glass doors can be cleaned using any standard glass cleaner
available on the market.
To clean interior non-metallic surfaces and removable parts,
wash with a mild solution of soap and lukewarm water with
a little baking soda. Rinse and dry thoroughly. Avoid getting
water on lights, control panel, fan motor, and unfinished
wood wine rack faces.
Caution
Do not use abrasive cleaners or cloths on any of the interior
or exterior surfaces or removable parts.
Cleaning the Condenser
The condenser should be cleaned every 3 months. The condenser is located behind the toe plate (Figure 6). Remove the
toe plate and use a soft bristle brush and vacuum to remove
dust and lint. Avoid damaging or crushing the condenser fins
or tubing. Upon completion, re-install the toe plate.
Caution
Failure to clean the condenser could result in temperature loss
or mechanical failure. Clean this area every three months.
The units are pre-set to achieve the recommended temperature range when installed in a 70°F ambient environment.
Factors which affect the internal temperatures of the cabinet
include the following:
•Temperature setting
•Room temperature where installed
•Number of times the door/drawer is opened and closed
•Length of time door/drawer is left opened
• Adjacent compartment temperature
• Style of door installed
10
© 2009
24” Signature Series Operation / Installation Manual
Primary Key Functions
Turns on/off the power to the unit
Disabled
Manually defrosts the unit by holding button down
Displays minimum stored temperature, also used
for navigating control codes and changing
displayed values within the various menu options
Displays maximum stored temperature, also used
for navigating control codes and changing
displayed values within the various menu options.
Fast freezing cycle is started by holding button
down for 3 seconds.
Displays and allows setpoing adjustment.
Used to select a parameter or confirm
an operation in programming mode. If held for 3
seconds while max or min temperature is displayed,
it will erase that temperature from memory.
LED Alerts
SYMBOL
STATUS
ON
ALERT DEFINITION
The compressor is running
FLASHING
Anti-short cycle delay enabled (Programming phase when flashing with
FLASHING
Programming phase
ON
The defrost is enabled
FLASHING
Drip time in progress
?
ON
The fast-freezing cycle is enabled
ON
Alarm signal: Contact Service Representative immediately
ON
The light is on
)
Figure 11. Control Panel
© 2009
11
24” Signature Series Operation / Installation Manual
Troubleshooting
If the unit appears to be malfunctioning, read through the OPERATION section first, then check the guide below to identify and
resolve the problem.
DANGER
Electrocution hazard! Never attempt to repair or perform maintenance on the unit until the main electrical power has been disconnected.
No interior light
• Is the bulb loose?
• Is the bulb burned out?
Light stays on when the door is closed
• Manual ON/OFF light switch is turn on.
• Is the door switch making contact with the door?
Noisy during operation
•Certain sounds are normal. Soft sounds from the compressor, fan motor and valves will be heard.
•During freezer defrost, crackling is normal.
Control display is flashing “P1”
•There is a thermostat failure.
Control display is flashing “P2”
•There is an evaporator probe failure.
Control display is flashing “HA”
•The internal compartment temperature has exceeded the high temperature alarm preset value for over 30 minutes.
•Check to ensure door is closed.
•Check for door gasket seal.
• Was warm product just installed?
• Is the condenser clean?
• Is the louvered toe plate obstructed?
• Has the surrounding ambient temperature changed dramatically?
• Is the interior light on?
Control display flashing “LA”
•The internal compartment temperature has exceeded the high temperature alarm preset value for over 30 minutes.
•Check to ensure door is closed.
•Check for door gasket seal.
• Has the surrounding ambient temperature changed dramatically?
Control display flashing “EE”
•The controller has a data or memory failure.
12
© 2009
24” Signature Series Operation / Installation Manual
The refrigerated cabinet isn’t running
• Is there electrical power to the unit?
• Is the building circuit breaker or fuse on?
• Is the ON/OFF keypad on?
• Is the condenser area clean?
The refrigerated compartment is warmer than usual
• Is the control set properly?
• Is the light staying on?
• Is the condenser area clean and free of obstruction?
• Has the door been open for a long time or more frequent door openings occurred?
• Are the internal louvers and fan guard openings obstructed?
The refrigerated compartment is cooler than usual
• Is the control set properly?
• Is the door closing and sealing properly?
The refrigeration runs for long periods of time
• Is the condenser area clean and free of obstruction?
• Has the door been open for a long time or more frequent door openings occurred?
• Has warm product just been placed in the unit?
• On hot days and in warm room temperatures, the system will run longer.
Condensation forms inside the refrigerated compartments
•This is normal during high humidity and frequent door openings.
• Are the doors closing and sealing properly?
Condensation forms on the outside of the unit
•During periods of high humidity, some condensation might appear on the outside surface. The condensation will disappear
when the humidity drops. Meanwhile, be sure doors are closing and sealing properly. If condensation persists, contact your
Perlick Factory Authorized Service Center.
To obtain product information
•Contact your selling dealer.
• Inquire on the web at www.bringperlickhome.com.
•Call 800/558-5592 for factory assistance for information for planning, installation or product information.
• Write to Perlick Corporation, Customer Service Department, 8300 W. Good Hope Road, Milwaukee, WI 53223.
• E-mail us at [email protected]
To obtain product service, replacement parts or accessories
•Use only genuine Perlick replacement parts and accessories. Genuine Perlick parts and accessories are designed to work correctly with Perlick products and offer superior service life. The use of non-Perlick parts can damage the unit and may void the
warranty.
•Check the model and serial number of the unit located on the label attached to the inside top of the cabinet.
Call a Perlick Factory Authorized Service Center. For the location of the nearest Service Center, contact your deal© 2009
13
24” Signature Series Operation / Installation Manual
Perlick Home Refrigeration Products Limited Warranty
ENTIRE PRODUCT- Full Two Year Warranty:
For two years from the date of original installation, Perlick Corporation’s warranty covers all parts and labor to repair or replace
any part of the product, which proves to be defective in material and workmanship.
Additional- Third Through Sixth Year Limited Parts Only Warranty:
During the four years following expiration of the Two Year Limited Warranty, Perlick will supply replacement parts only for the
hermetically sealed refrigeration system which consist of the compressor, condenser, drier, connecting tubing, evaporator, and
hot gas bypass valve.
TERMS:
The Perlick Warranty applies to products installed in the fifty United States, the District of Columbia or the ten provinces of
Canada.
All service provided by Perlick Corporation under the above warranty must be performed by authorized Perlick service representatives, unless otherwise specified by Perlick.
Service will be provided in the home during normal business hours.
This warranty applies only to products installed for normal residential use, it does not include adjusting the controls, door reversal, light bulb or cleaning the condenser.
This warranty is extended only to the original purchaser of the Perlick product.
The above warranty does not apply if:
•Failure of product was due to transportation
• Product was: improperly installed, misused, abused, operating with low voltage, wiring not conforming electrical codes,
improperly maintained or modified.
•The original Bill of Sale, delivery date or serial number cannot be verified.
•Defective parts are not returned for inspection if so required by the Perlick Corporation.
To receive parts and or service and the name of the nearest Perlick authorized service representative, contact your Perlick dealer,
distributor or Perlick Corporation’s Customer Service Department; 8300 West Good Hope Road, Milwaukee Wisconsin, 53223; call
800/777-7267, E-mail us at [email protected] , or visit our web: www.perlick.com.
This limited warranty is in lieu of any other warranty, expressed or implied, including, but not limited to any implied warranty of
merchantability or fitness for a particular purpose; provided however, that to the extent required by law, implied warranties are
included but do not extend beyond the duration of the express warranty first set above. Perlick’s sole liability and your exclusive
remedy under this warranty are set forth in the initial paragraph above. Perlick Corporation shall have no liability whatsoever
for any incidental, consequential or special damages arising from the sale, use or installation of the product or from any other
causes whatsoever, whether based on warranty (expressed or implied) or otherwise based on contract, tort or any other theory
of liability.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and you may also
have other rights, which vary, from state to state.
14
© 2009
24” Signature Series Operation / Installation Manual
NOTES
© 2009
15
24” Signature Series Operation / Installation Manual
NOTES
16
© 2009
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement