Epson 835p - PowerLite XGA LCD Projector User`s guide

User's Guide.book Page 1 Tuesday, May 25, 2004 11:49 AM
Epson PowerLite 830p
Multimedia Projector
®
®
User’s Guide
User's Guide.book Page 2 Tuesday, May 25, 2004 11:49 AM
Important Safety Information
WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.
Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and
filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically
explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service
personnel.
WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small
children to avoid any risk of suffocation.
Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by
the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.
Copyright Notice
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of Seiko Epson Corporation. The information contained herein is designed only for use with
this Epson product. Epson is not responsible for any use of this information as applied to other products.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for
damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of
this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to
strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.
Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or
any consumable products other than those designated as Original Epson Products or Epson Approved Products by
Seiko Epson Corporation.
Epson is a registered trademark, and EasyManagement, EasyMP, Quick Corner, and Wall Shot are trademarks of
Seiko Epson Corporation.
PrivateLine, Presenters Club, and PowerLite are registered trademarks; SizeWise is a trademark; and Epson
Connection, Epson Store, and Extra Care are service marks of Epson America, Inc.
Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
© 2004 Epson America, Inc.
5/04
CPD-18223
2
User's Guide.book Page 3 Tuesday, May 25, 2004 11:49 AM
Contents
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 10
Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 10
Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Additional Components. . . . . . . . . . . . . . . . . . . . . . . . . 12
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1
Displaying and Adjusting the Image . . . . . . . . 15
Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Projecting the Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 18
Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 20
Troubleshooting Display Problems. . . . . . . . . . . . . . . . . . . . 21
You Can’t Project an Image . . . . . . . . . . . . . . . . . . . . . . 21
The Projector and Notebook Don’t Display the Same
Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Adjusting the Height of Your Image . . . . . . . . . . . . . . . 24
Using Quick Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Focusing and Zooming Your Image . . . . . . . . . . . . . . . . 25
Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 26
Correcting Computer Images. . . . . . . . . . . . . . . . . . . . . 28
Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 29
Using the Direct Power On Function . . . . . . . . . . . . . . 30
3
User's Guide.book Page 4 Tuesday, May 25, 2004 11:49 AM
2
3
Using the Remote Control . . . . . . . . . . . . . . . . . . . 31
Turning On and Using the Remote Control . . . . . . . . . . . . 32
Replacing the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . 33
Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 34
Switching Between Picture Sources . . . . . . . . . . . . . . . . 34
Previewing Picture Sources . . . . . . . . . . . . . . . . . . . . . . 35
Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 36
Turning Off the Picture and Sound . . . . . . . . . . . . . . . . 37
Stopping Action. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Zooming Part of Your Image . . . . . . . . . . . . . . . . . . . . . 38
Displaying a Picture-in-Picture Video . . . . . . . . . . . . . . 38
Controlling the Volume. . . . . . . . . . . . . . . . . . . . . . . . . 39
Projecting Images Without a Screen . . . . . . . . . . . . . . . . . . . 40
Making Initial Color Corrections. . . . . . . . . . . . . . . . . . 40
Adjusting Color Corrections for a New Surface . . . . . . . 41
Operating Your Computer with the Remote Control . . . . . . 41
Highlighting Your Presentation . . . . . . . . . . . . . . . . . . . . . . 43
Using the Pointer Tool . . . . . . . . . . . . . . . . . . . . . . . . . 43
Customizing the Pointer Tools . . . . . . . . . . . . . . . . . . . 44
Connecting to Computers and Other
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . 46
Connecting to the Computer Ports . . . . . . . . . . . . . . . . 47
Using the Macintosh Desktop Adapter . . . . . . . . . . . . . 48
Connecting the Cable for Remote Mouse Control . . . . 49
Connecting an External Monitor . . . . . . . . . . . . . . . . . . . . . 50
Connecting to Video Equipment . . . . . . . . . . . . . . . . . . . . . 51
Connecting a Composite Video Source . . . . . . . . . . . . . 52
Connecting an S-Video Source . . . . . . . . . . . . . . . . . . . 53
Connecting a Component Video Source . . . . . . . . . . . . 54
Connecting an RGB Video Source. . . . . . . . . . . . . . . . . 55
Playing Sound Through the Projector . . . . . . . . . . . . . . . . . 56
Connecting Audio Equipment to the Projector . . . . . . . 56
Connecting External Speakers . . . . . . . . . . . . . . . . . . . . 57
4
Contents
User's Guide.book Page 5 Tuesday, May 25, 2004 11:49 AM
4
Fine-Tuning the Projector . . . . . . . . . . . . . . . . . . . 59
5
Managing Projectors
Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . 61
Adjusting the Image Quality. . . . . . . . . . . . . . . . . . . . . . . . . 62
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Adjusting Signal Settings . . . . . . . . . . . . . . . . . . . . . . . . 63
Adjusting the Image Size, Shape, and Position . . . . . . . . . . . 65
Adjusting the Color . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Adjusting the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Using the Projector Security Features . . . . . . . . . . . . . . . . . . 67
Enabling Password Protection . . . . . . . . . . . . . . . . . . . . 68
Creating Your Own Startup Screen . . . . . . . . . . . . . . . . 71
Disabling the Projector’s Buttons . . . . . . . . . . . . . . . . . . 72
Controlling Multiple Projectors . . . . . . . . . . . . . . . . . . . . . . 73
Setting the Projector ID . . . . . . . . . . . . . . . . . . . . . . . . . 73
Changing the Remote Control ID . . . . . . . . . . . . . . . . . 74
Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 75
Remote Monitoring Setup Options . . . . . . . . . . . . . . . . 75
Miscellaneous Setup Options . . . . . . . . . . . . . . . . . . . . . 75
Enabling Quick Setup Options. . . . . . . . . . . . . . . . . . . . . . . 76
Automatically Running Quick Setup . . . . . . . . . . . . . . . 77
. . . . . . . . . . . . . . . . . . . . . . . . 79
Connecting and Configuring the Projector on a Wired
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Using EMP Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Opening and Closing EMP Monitor . . . . . . . . . . . . . . . 82
Registering Your Projectors . . . . . . . . . . . . . . . . . . . . . . 82
Monitoring Your Projectors . . . . . . . . . . . . . . . . . . . . . . 85
Controlling Your Projectors . . . . . . . . . . . . . . . . . . . . . . 87
Using EMP NetworkManager . . . . . . . . . . . . . . . . . . . . . . . 89
Selecting the Projectors to Monitor . . . . . . . . . . . . . . . . 89
Setting a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Creating the E-Mail Settings . . . . . . . . . . . . . . . . . . . . . 90
Understanding the Notification Messages . . . . . . . . . . . 93
Contents 5
User's Guide.book Page 6 Tuesday, May 25, 2004 11:49 AM
6
7
A
B
6
Contents
Maintaining the Projector. . . . . . . . . . . . . . . . . . . 95
Cleaning the Lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 96
Cleaning the Air Filters and Vents . . . . . . . . . . . . . . . . . . . . 96
Replacing the Lamp and Air Filters . . . . . . . . . . . . . . . . . . . 97
Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . 99
Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . 100
Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Using On-Screen Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
Checking Projector Status . . . . . . . . . . . . . . . . . . . . . . . . . 103
What To Do When the Lights Flash . . . . . . . . . . . . . . 103
Viewing Lamp Usage and Other Information . . . . . . . 105
Solving Problems with the Image or Sound . . . . . . . . . . . . 105
Solving EasyManagement Problems . . . . . . . . . . . . . . . . . 111
Solving Problems with the Remote Control . . . . . . . . . . . . 111
Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Telephone Support Services . . . . . . . . . . . . . . . . . . . . . 112
Software Installation . . . . . . . . . . . . . . . . . . . . . . . 113
Windows System Requirements . . . . . . . . . . . . . . . . . . . . . 113
Installing the Software on a Windows System . . . . . . . . . . 114
Projector Installation . . . . . . . . . . . . . . . . . . . . . . . 115
User's Guide.book Page 7 Tuesday, May 25, 2004 11:49 AM
C
Technical Specifications . . . . . . . . . . . . . . . . . . . . 117
D
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Projection Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Electrical. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Compatible Video Formats. . . . . . . . . . . . . . . . . . . . . . . . . 119
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 121
Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . 123
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . 124
FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 125
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Contents 7
User's Guide.book Page 8 Tuesday, May 25, 2004 11:49 AM
8
Contents
User's Guide.book Page 9 Tuesday, May 25, 2004 11:49 AM
-
Welcome
The Epson
® PowerLite®
830p is an easy-to-use, lightweight
projector that offers up to 3000 lumens of brightness and a 600:1
contrast ratio for incredibly vivid images and clear text.
Versatility
You can connect it to a wide range of computers and video sources, or
you can project over a wired LAN network.
Ease of use
The projector’s keystone correction and Quick Corner™ features
automatically correct image distortion, and Epson’s unique Wall
Shot™ function lets you project against blackboards and colored walls
without loss of image color, regardless of ambient lighting. The
projector also automatically focuses the projected image. These
features can all be set to automatically create the best image projection
by pressing a single button.
Complete control
Use the remote control to take charge of your presentation. Freeze the
action, zoom in on part of the picture, or display a picture-in-picture
video. Use the remote as a pointer, or to draw on the screen. You can
even use it in place of your computer’s mouse to control your
computer and change slides in Microsoft® PowerPoint.®
EasyManagement
With the projector’s EasyManagement™ system, you can use a
Windows® PC to remotely monitor and control the projector over a
network.
Security
To prevent unauthorized use, this projector includes several security
features including a password, user’s logo, and the ability to lock the
projector buttons.
9
User's Guide.book Page 10 Tuesday, May 25, 2004 11:49 AM
Using Your Documentation
This book contains all the information you need to set up and use
your projector. Please follow these guidelines as you read through it:
■
Warnings must be followed carefully to avoid bodily injury.
■
Cautions must be observed to avoid damage to your equipment.
■
Notes contain important information about your projector.
■
Tips contain additional projection hints.
Getting More Information
Need tips on giving presentations? Quick steps for setting up your
projector? Here’s where you can look for help:
■
presentersonline.com
Includes a library of articles covering presentation tips, tricks, and
technology. The site provides templates, clip art and sound clips,
as well as Presenters Services to use on the road. Even more
resources and services are available if you register to join the
Presenters Club®—and it’s free.
■
Quick Setup sheet
Gives you the instructions you need to get your projector up and
running if you are connecting to a notebook, PowerBook,® or
iBook® computer.
■
Start Here kit
Includes this User’s Guide, your Quick Setup sheet, warranty
brochures, and Epson PrivateLine® Support card. Keep the folder
with your projector at all times.
■
Built-in help system
Provides assistance for common problems. Available from the
Help button on the projector or the remote control. See page 102
for details.
■
support.epson.com
Download FAQs and e-mail your questions to Epson support.
10
Welcome
User's Guide.book Page 11 Tuesday, May 25, 2004 11:49 AM
■
If you still need help after checking this User’s Guide and the
sources listed above, you can use the Epson PrivateLine Support
service to get help fast. Call (800) 637-7661 and enter the PIN on
the card in your Start Here kit. Or take advantage of Epson’s
automated support services 24 hours a day. See page 112 for more
information.
Registration and Warranty
Your projector comes with a basic carry-in warranty as well as an
international warranty that let you project with confidence anywhere
in the world. For details, see page 126 and the warranty brochure
included in your Start Here kit.
In addition, for customers who register their projector, Epson offers
free Extra CareSM Road Service. In the unlikely event of an equipment
failure, you won’t have to wait for your unit to be repaired. Instead,
Epson will ship you a replacement unit anywhere in the United States
or Canada, usually via overnight delivery. See the brochure in your
Start Here kit for details.
To register, simply fill out the registration card included in your Start
Here kit and mail it to Epson. Or you can register online at
http://www.epson.com/webreg. Registering also lets you receive
special updates on new accessories, products, and service.
Welcome 11
User's Guide.book Page 12 Tuesday, May 25, 2004 11:49 AM
Unpacking the Projector
After unpacking the projector, make sure you have all the parts shown
below:
note
You won’t need all these
components; your
configuration will determine
which ones you need.
Remote control and
batteries
Projector software
CD-ROM
Projector
USB cable
Power cable
VGA computer cable
Save all packaging in case you need to ship the projector. Always use
the original packaging (or the equivalent) when you need to send the
projector to another location. If you are moving the projector by
hand, use a carrying case. See page 13 for ordering information, and
page 100 for transportation instructions.
Additional Components
Depending on how you plan to use the projector, you may need
additional components:
12
Welcome
■
To receive an S-Video signal, you’ll need an S-Video cable. One
may be provided with your video equipment, or you can purchase
one from Epson; see page 13.
■
To receive a component video signal from a VCR or other video
device, you’ll need a component video cable. You can purchase
one from Epson; see page 13.
User's Guide.book Page 13 Tuesday, May 25, 2004 11:49 AM
■
Some older PowerBooks® and Macintosh® desktop models may
need the Macintosh desktop adapter set shown on page 48
(available from Epson; see page 13.) Older iMac® systems may
need a special adapter to provide a VGA output port; see your
computer dealer.
Optional Accessories
To enhance your use of the projector, Epson provides the following
optional accessories:
Product
Part number
Replacement lamp
V13H010L31
Air filter replacement set
V13H134A07
ATA molded hardshell case
Samsonite® wheeled soft case
ELPKS35
ELPKS52
Ceiling mount
Suspension adapter
False ceiling plate
Security bracket/cabling for gyro lock mounts
Adjustable ceiling channel
ELPMB36
ELPMBAPL
ELPMBFCP
ELPMBSEC
ELPMBACC
Kensington® security lock
ELPSL01
Projection screens:
50-inch portable screen
60-inch portable pop-up screen
80-inch portable pop-up screen
83.6-inch hanging pull-down screen
ELPSC06
ELPSC07
ELPSC08
ELPSC09
Macintosh adapter set
ELPAP01
Component video cable
S-Video cable
ELPKC19
ELPSV01
Distribution amplifier
ELPDA01
Image Presentation Camera
High resolution document camera
V12H162020
V12H064020
You can purchase these accessories from your dealer, by calling
Epson at (800) 873-7766, or by visiting the Epson StoreSM at
www.epsonstore.com (U.S. sales only). In Canada, please call
(800) 463-7766 for dealer referral.
Welcome 13
User's Guide.book Page 14 Tuesday, May 25, 2004 11:49 AM
14
Welcome
User's Guide.book Page 15 Tuesday, May 25, 2004 11:49 AM
1
Displaying and Adjusting
the Image
W
hether you’re presenting from a computer or video equipment,
you need to follow some basic steps to display your image on the
screen.
Follow the guidelines in this chapter for:
■
Positioning the projector
■
Turning the projector on and selecting the image source
■
Troubleshooting display problems
■
Adjusting the image
■
Turning off the projector
15
User's Guide.book Page 16 Tuesday, May 25, 2004 11:49 AM
Positioning the Projector
note
You can mount the projector
on the ceiling, or place it
behind a translucent screen
for rear projection. See
page 115 for details.
If the projector isn’t already installed in the room you’re using, you’ll
probably want to place it on a table in front of the screen, as shown.
This lets you stand in the front of the room, face the audience, and
remain close enough to the equipment to be able to control it. Try to
leave as much space as possible between the projector and the screen to
get a good-size image.
Use the figure below to help you determine placement. Image size
increases with distance, but can vary depending on how you position
the zoom ring and whether you’ve adjusted the image with other
settings.
TBD
29.8 to 48.3 ft
5.8 to 9.5 ft
2.8 to 4.7 ft
Distance from screen
Also keep these considerations in mind:
16
■
Place the projector on a sturdy, level surface.
■
Make sure there is plenty of space for ventilation around and
under the projector. Do not set the projector on top of anything
that could block the vents under the projector.
■
Make sure the projector is within 10 feet of a grounded electrical
outlet or extension cord.
Displaying and Adjusting the Image
User's Guide.book Page 17 Tuesday, May 25, 2004 11:49 AM
Ideally, you should place the projector directly in front of the center of
the screen, facing it toward the screen squarely. The base of the lens
should be at about the level of the bottom of the screen.
Projector
note
After positioning the
projector, you may want to
connect a Kensington
MicroSaver® anti-theft
device to the lock port on the
projector’s left side. You can
purchase this from Epson;
see “Optional Accessories” on
page 13.
Screen
If you place the projector below screen level, you’ll have to tilt it up by
extending the front adjustable foot. This causes the image to become
“keystone” shaped, but you can correct the distortion by pressing the
Sync buttons on the projector. See page 26 for detailed information
about correcting the image shape.
For instructions on installing the projector in a permanent location,
such as a theater or conference room, see page 115.
Displaying and Adjusting the Image 17
User's Guide.book Page 18 Tuesday, May 25, 2004 11:49 AM
Projecting the Image
Make sure your projector and other equipment are set up as described
on page 45. Then follow the instructions below to start the projector
and display an image.
Turning On the Projector
note
To shut down the projector,
see page 29. Shutting down
the projector correctly
prevents premature lamp
failure and possible damage
from overheating.
Turn on any connected computer or video equipment before starting
the projector so it can automatically detect and display the image
source. If you turn on the projector first, or have multiple pieces of
connected equipment, you may have to select the image source
manually (see page 20).
Follow these steps to turn on the projector:
1. Remove the lens cap.
2. Plug one end of the power cable into the projector, and the other
end into a grounded electrical outlet.
3. Wait until the Power light stops flashing and turns orange.
Power light
18
Displaying and Adjusting the Image
User's Guide.book Page 19 Tuesday, May 25, 2004 11:49 AM
4. Press the red P Power button on top of the projector—or press
the P Power button on the remote control.
Power button
(If this is your first time using the remote control, make sure the
batteries are installed and the ON/OFF switch on the side of the
remote is turned on.)
Turn on
remote
Power button
The projector beeps once and the Power light flashes green as the
projector warms up, then an image begins to appear. When the
Power light stops flashing and remains green, the projector is
ready for use.
5. If you’ve connected a Windows-based computer to the projector,
you may see a New Hardware Wizard screen saying your
computer has found a plug-and-play monitor; if so, click Cancel.
warning
Never look into the lens
when the lamp is on. This
can damage your eyes, and is
especially dangerous for
children.
6. If you are prompted to enter a password, see page 68.
Displaying and Adjusting the Image 19
User's Guide.book Page 20 Tuesday, May 25, 2004 11:49 AM
Selecting the Image Source
note
To focus and adjust the
image, see page 24. If a
projected image fails to
appear, see page 21 for help.
Selecting the image source lets you switch between images input from
different pieces of connected equipment (such as a computer or DVD
player).
If you don’t see the image you want, press the Source Search button
on the remote control or the projector.
You can also select your image using the Source buttons either on the
projector or the remote control as follows:
■
The projector has two Source buttons. Use the
Computer/Component button to switch between equipment
connected to the Computer/Component ports.
Use the Video/S-Video button to switch between equipment
connected to the Video and S-Video ports.
■
The remote control has four source buttons. Use them to switch
between devices connected to the ports identified on each button.
The PowerLite 830p does not support EasyMP.TM
You can also press the Source Search button on the projector or the
remote repeatedly until you see the image you want to project on the
screen.
note
You can also preview all
sources on one screen to help
you select the desired source
(see page 35).
20
Displaying and Adjusting the Image
User's Guide.book Page 21 Tuesday, May 25, 2004 11:49 AM
Troubleshooting Display Problems
Follow these guidelines if you’re having trouble displaying an image.
You Can’t Project an Image
If you don’t see the image you are trying to project, try the following:
■
Make sure the cables are connected correctly, as described
beginning on page 45.
■
Make sure the Power light is green and not flashing and the lens
cap is off.
■
If you’ve connected more than one computer and/or video source,
you may need to press one of the Source buttons on the
projector’s control panel or the remote control to select the
correct source. (Allow a few seconds for the projector to sync up
after pressing the button.)
■
If you’re using a PC notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be
labeled CRT/LCD or have an icon such as
. You may have to
hold down the Fn key while pressing it. Allow a few seconds for
the projector to sync up after changing the setting.
The Projector and Notebook Don’t Display the
Same Image
If you’re projecting from a notebook, and you can’t see your image on
the projection screen and on your computer at the same time, follow
these guidelines.
If you’re using a PC notebook:
■
On most systems, there’s a function key that lets you toggle
between the LCD screen and the projector, or display on both at
the same time. It may be labeled CRT/LCD or have an icon such as
. You may have to hold down the Fn key while pressing it.
Allow a few seconds for the projector to sync up after changing
the setting.
Displaying and Adjusting the Image 21
User's Guide.book Page 22 Tuesday, May 25, 2004 11:49 AM
■
If the function key doesn’t permit you to display simultaneously
on both screens, you should check your monitor settings to make
sure both the LCD screen and the external monitor port are
enabled.
From the Control Panel, open the Display utility. In the Display
Properties dialog box, click the Settings tab, then click
Advanced. The method for adjusting the settings varies by
brand; you may need to click a Monitor tab, then make sure the
external Monitor port is set as your primary display and/or
enabled. See your computer’s documentation or online help for
details.
If you’re using Macintosh OS X:
You may need to set up your system to display on the projector screen
as well as the LCD screen. Follow these steps:
1. From the Apple menu, select System Preferences, then select
Displays.
2. Make sure the VGA Display or Color LCD dialog box is selected.
3. Click the Arrangement (or Arrange) tab.
Make sure
Mirror Displays
is checked
4. Make sure the Mirror Displays checkbox is selected.
22
Displaying and Adjusting the Image
User's Guide.book Page 23 Tuesday, May 25, 2004 11:49 AM
If you’re using OS 8.6 to OS 9.x:
You may need to set up your system to display on the projector screen
as well as the LCD screen. Follow these steps:
1. From the Apple menu, select Control Panels, then click
Monitors or Monitors and Sound.
2. Click the Arrange icon.
Click here
Drag one
monitor icon on
top of the other
3. Drag one monitor icon on top of the other.
If the Arrange option isn’t available, you may need to select one of the
Simulscan resolution settings:
1. Click the Monitor icon.
Click here
Select a
Simulscan
resolution
2. Select a Simulscan resolution as shown. (Allow a few seconds for
the projector to sync up after making the selection.)
Displaying and Adjusting the Image 23
User's Guide.book Page 24 Tuesday, May 25, 2004 11:49 AM
Adjusting the Image
Once you see your image, you need to make certain adjustments:
■
If the image is too high or too low, you can reposition it. See
below.
■
If you have quick setup enabled on the projector, see page 25.
■
To focus or zoom your image, see page 25.
■
If the image isn’t square, see page 26.
■
If a computer image displays incorrectly, see page 28.
If you need to fine-tune the image and/or sound, see Chapter 4.
Adjusting the Height of Your Image
If the image is too low on the screen, you can use the front adjustable
foot to raise it.
1. Stand behind the projector. Press the blue foot release lever up
and lift the front of the projector.
2. Once the image is positioned where you want it, release the lever
to lock the foot in position.
3. If necessary, you can fine-tune the height or level the image by
turning the projector’s rear feet.
Projector rear foot
24
Raising the projector causes the image to distort or “keystone,” but
you can manually correct the shape as described in the next section.
Displaying and Adjusting the Image
User's Guide.book Page 25 Tuesday, May 25, 2004 11:49 AM
Using Quick Setup
You can use the Quick Setup button on the projector or the remote
control to quickly and automatically set up the projector’s focus,
zoom, and shape, as well as the Wall Shot setting. All you need to do is
position your projector, then press Quick Setup. Make sure you
enable Quick Setup for all of the settings you want to use as described
on page 76.
Quick Setup
Focusing and Zooming Your Image
Use the Focus buttons on the projector or remote to sharpen the
image.
Use the Zoom buttons on the projector or remote to reduce or enlarge
the image. Press the W button on the projector or the top zoom
button on the remote to increase the size, and the T button on the
projector or bottom zoom button on the remote to decrease it.
Focus
Zoom
If the image still isn’t large enough, you may need to move the
projector farther away from the screen. You can also use the E-Zoom
buttons on the remote control to zoom in on a portion of the image.
See page 38 for instructions.
Displaying and Adjusting the Image 25
User's Guide.book Page 26 Tuesday, May 25, 2004 11:49 AM
Adjusting the Image Shape
In most cases, you can maintain a square or rectangular image by
placing the projector directly in front of the center of the screen with
the base of the lens level with the bottom of the screen.
Even if the projector is slightly tilted (within a range of 40° up or
down), the projector has an automatic keystone correction function
that detects and corrects vertical keystone distortion.
Projector tilted up
Corrected image
Projector tilted down
It takes about one second after projection starts for the image to be
corrected. During this time, a vertical keystone correction gauge
appears on the screen.
If your image is still distorted, you can correct it using either of these
methods:
■
If the image has two parallel sides but is wider on one side (top,
bottom, left, or right), you can correct it using the Keystone
buttons on the projector’s control panel (see page 27) or the
projector’s Keystone menu (see page 27).
■
If the image has no parallel sides, you can adjust its shape using
Quick Corner (see page 36).
Keystone correction
Keystone correction
You cannot use both keystone correction and Quick Corner at the
same time.
Quick Corner correction
26
Displaying and Adjusting the Image
User's Guide.book Page 27 Tuesday, May 25, 2004 11:49 AM
Using Keystone Correction
To adjust your image when it is wider on one side, do the following:
■
Look at the shapes of the icons on the projector’s four keystone
buttons. Press the button whose icon is the opposite of the shape
of your screen image. Continue pressing the button until you are
satisfied with the shape of the image.
note
The image will be slightly
smaller after adjusting. If
it’s important to maintain
the correct aspect ratio, use
the menu system to perform
keystone correction, then use
the remote’s Resize button
to adjust the aspect ratio. See
page 65.
Keystone
buttons
■
Or press the Menu button on the remote control, select the
Setting menu, and press Enter. From the Setting menu, select
Keystone and press Enter, select H/V Keystone and press Enter,
then select Horiz./Vert./Height and press Enter. Select
V-Keystone (for vertical keystone distortion) or H-Keystone
(for horizontal keystone distortion) and press Enter. Use the
pointer button on the remote control to adjust the keystone
setting as needed.
Menu
button
Displaying and Adjusting the Image 27
User's Guide.book Page 28 Tuesday, May 25, 2004 11:49 AM
Correcting Computer Images
note
You must be projecting an
image for this button to have
any effect. The Auto button
works only with computer
images.
If you’re connected to a computer and the image doesn’t look right,
press the Auto button on the remote control. This automatically
resets the projector’s tracking, sync, resolution, and position settings.
Auto button
If vertical bands appear in the projected image and the Auto button
doesn’t correct the problem, hold down the Shift button on the
projector’s control panel while pressing either the Tracking + or the
Tracking - button.
If the image appears fuzzy or flickers and the Auto button doesn’t
correct the problem, hold down the Shift button while pressing either
the Sync + or Sync - button on the projector.
28
Displaying and Adjusting the Image
User's Guide.book Page 29 Tuesday, May 25, 2004 11:49 AM
Shutting Down the Projector
note
When you’ve finished using the projector, follow the recommended
procedure to shut it down. This extends the life of the lamp and
protects the projector from possible overheating.
1. Turn off any equipment plugged into the projector.
2. To turn off the projector, press the red P Power button on the
projector or remote control.
Power button
You can set the projector to
automatically turn off the
projector lamp and enter
“sleep mode” when it has not
received any signals for 30
minutes. This conserves
electricity, cools the
projector, and extends the
life of the lamp. If you want
to start projecting again,
press the P Power button.
If you are done using the
projector, unplug the power
cord. To turn off sleep
(standby) mode, see page 75.
You see a confirmation message. (If you don’t want to turn it off,
press any other button.)
3. Press the P Power button again. The projector beeps twice, the
lamp is turned off, and the Power light flashes orange for about
30 seconds as the projector cools down. After the projector has
cooled, the orange light stays on and the exhaust fan shuts off.
If you want to turn the projector on again, wait until the orange
light stops flashing. Then press the P Power button.
caution
Turn the projector off when
not in use. Continuous
24-hour-a-day use may
reduce the projector’s overall
life.
4. If you extended the adjustable front foot, press up on the blue
foot release lever to retract it.
5. Replace the lens cap and unplug the power cord.
6. If you’re using a remote control, set its ON/OFF switch to OFF.
Displaying and Adjusting the Image 29
User's Guide.book Page 30 Tuesday, May 25, 2004 11:49 AM
Using the Direct Power On Function
The Direct Power On function enables fast and easy setup and shut
down. This feature is convenient for ceiling mounted projectors
because you can simply flip a switch that is connected to the power
outlet for the projector to turn it on or off. For desktop or table-top
use, you can quickly unplug the projector immediately without having
to wait for it to cool down. Then you can pack up the projector and
go.
Follow these steps to enable Direct Power On:
1. Press the Menu button on the remote control and select the
Extended menu.
2. Choose Operation and press Enter.
3. Choose Direct Power On and press Enter.
4. Highlight On and press Enter.
5. Press Esc or Menu to exit.
30
Displaying and Adjusting the Image
User's Guide.book Page 31 Tuesday, May 25, 2004 11:49 AM
1
Using the Remote Control
T
he projector includes a number of tools to enhance your
presentation. All of them can be accessed using the remote control,
which lets you operate the projector from anywhere in the room—up
to 33 feet away.
note
For information and
resources to help you give
the most professional
presentation, be sure to visit
presentersonline.com.
You can use the remote control to adjust the picture and sound
(page 34) or as a pointer to highlight your presentation (page 43). You
can also use it to make automatic color corrections that let you project
images onto any surface (page 40) or as a wireless mouse when
projecting from a computer (page 41).
This chapter covers:
■
Turning on and using the remote control
■
Controlling the picture and sound
■
Projecting images without a screen
■
Operating your computer with the remote control
■
Highlighting your presentation
31
User's Guide.book Page 32 Tuesday, May 25, 2004 11:49 AM
Turning On and Using the Remote
Control
The remote control has an ON/OFF switch on its side, as shown.
Before using the remote, make sure batteries are installed as described
on page 33, then push up on the ON/OFF switch to turn it on.
ON/OFF switch
note
If a button is pressed longer
than 60 seconds, the remote
control stops operating to
conserve power. When you
release the button, normal
operation resumes.
32
Turn off the remote control before transporting or storing it; this
prevents the batteries from discharging if something presses against
one of the buttons.
Here are some additional tips:
■
Point the remote control either at the front or back of the
projector, or at the screen.
■
Stand within 33 feet of the projector. If you want to operate the
projector from a greater distance, a remote control cable set is
available (see page 13).
■
When presenting in a darkened room, press the light button to
make the buttons on the remote light up temporarily.
■
Avoid using the remote under bright fluorescent lamps or in
direct sunlight, or the projector may not respond properly.
Using the Remote Control
User's Guide.book Page 33 Tuesday, May 25, 2004 11:49 AM
Replacing the Batteries
If the projector stops responding to the remote control, check the
following:
■
Make sure the remote control’s ON/OFF switch (shown on
page 32) is in the ON position.
■
Press the light button and check to see if the buttons on the
remote control light up. (If you’re in a bright room, you may not
be able to see them light up.)
If the buttons do not light up, replace the batteries as described below:
caution
1. Turn the remote control over.
When replacing batteries,
take the following
precautions:
2. Press down on the ridges at one
end of the battery cover as you
slide the cover off.
3. Install two AA batteries, inserting
the flat (negative) ends in first.
Replace the batteries as
soon as they run out. If the
batteries leak, wipe away
battery fluid with a soft
cloth. If fluid gets on your
hands, wash immediately.
■
Do not expose batteries to
heat or flame.
■
Dispose of used batteries
according to local
regulations.
■
Remove the batteries if
you won’t be using the
projector for a long period of
time.
■
4. Slide the cover back in place.
Using the Remote Control 33
User's Guide.book Page 34 Tuesday, May 25, 2004 11:49 AM
Controlling the Picture and Sound
note
You can use the projector’s
menus to fine-tune the
picture and sound quality as
described on page 59.
You can use the remote control to preview and select your picture
sources, temporarily turn off the picture and sound, freeze the action,
zoom in on the picture, display a picture-in-picture image, and adjust
the volume.
Switching Between Picture Sources
If your projector is connected to more than one computer and/or
video source, you can switch between the different sources:
■
The easiest way to select your source is to press the Source
Search button on the remote control or projector repeatedly
until you see the image you want on the screen.
■
On the projector’s control panel, there are three Source buttons:
Press the Source Search button to automatically search for any
image signals from connected devices, press the
Computer/Component button to switch between equipment
connected to the Computer/Component ports, or press the
Video/S-Video button to switch between equipment connected
to the Video and S-Video ports.
■
On the remote control, there are four Source buttons. Use them
to switch between equipment connected to the port identified on
each button.
After you select a source, the screen goes dark for a moment before the
image appears.
Source buttons
34
Using the Remote Control
User's Guide.book Page 35 Tuesday, May 25, 2004 11:49 AM
Previewing Picture Sources
You can display a preview image from each connected source to help
you select the image source you want.
1. Press Preview on the remote control.
Preview button
You see the currently selected source displayed in the main
window, as shown below. All other sources (including the
currently selected source) are displayed in smaller preview
windows on the right side and at the bottom. If no equipment is
connected to a port, there is no incoming signal, or the signal is
out of range, the preview window for that source appears blank.
note
Movies are displayed as
still images on the preview
screen.
Computer (Analog-RGB)
Currently
selected
source
Easy MP
Computer
Computer
S-Video
note
Video
Preview windows
2. Press one of the Source buttons on the remote control to switch
to the desired source. Press Enter to change the source and exit
the screen or press Esc to exit the preview screen without
switching sources.
A red highlight surrounds
the preview window for the
currently selected source. Use
the
pointer button on the
remote control to highlight a
different source and press
Enter to display it.
Using the Remote Control 35
User's Guide.book Page 36 Tuesday, May 25, 2004 11:49 AM
Adjusting the Image Shape
Even if your projected image has no parallel sides, you can even up the
sides using Quick Corner. Follow these steps:
1. Press the Menu button on the remote control (or on the
projector’s control panel).
2. Select the Setting menu and press Enter.
note
3. From the Setting menu, select Keystone and press Enter.
If you are already using
Keystone settings, you see a
warning message. To disable
keystone settings and use
Quick Corner instead, press
Enter; to keep your settings,
press Esc.
4. Select Quick Corner and press Enter.
You see this screen:
5. Press the Enter button to select the corner you want to adjust.
note
If you are not satisfied with
the corrections made, press
the Esc button for one
second to reset the screen to
its original shape.
6. Use the
pointer button on the remote control (or the arrow
buttons on the projector) to adjust the shape.
7. Repeat steps 5 and 6 as needed to adjust any remaining corners.
8. When done, press the Esc button on the remote control or
projector’s control panel to exit the menu system.
If Quick Corner remains selected in the Keystone menu, the Quick
Corner screen appears whenever you press the projector’s keystone
buttons. You can then follow steps 5 through 8 above to correct the
shape of your image or press Esc to exit Quick Corner.
36
Using the Remote Control
User's Guide.book Page 37 Tuesday, May 25, 2004 11:49 AM
Turning Off the Picture and Sound
You can use the A/V Mute button on the remote control to turn off
the image and sound and darken your screen. This feature is useful if
you want to temporarily redirect your audience’s attention without
the distraction of a bright screen.
■
To turn off the picture, press the A/V Mute button. The screen
goes dark.
■
To turn the image back on, press the button again.
note
If you’ve connected a
computer to one of the
projector’s Computer ports
and an external monitor to
the projector’s Monitor Out
port, the monitor will
continue displaying.
You can also have an image, such as a company logo, display on the
screen whenever you press the A/V Mute button (see page 71).
Stopping Action
You can use the remote control to stop the action in your video or
computer image.
note
This function pauses the
image, but not the sound.
Also, because the source
continues to transmit
signals, you won’t resume
the action from the point
you stopped it.
■
To stop the action and keep the current image on the screen, press
the Freeze button. The sound continues.
■
To restart it, press the Freeze button again.
Using the Remote Control 37
User's Guide.book Page 38 Tuesday, May 25, 2004 11:49 AM
Zooming Part of Your Image
You can zoom in on a portion of the image using the E-Zoom buttons
on the remote control.
1. Press the E-Zoom
button on the remote control.
You see a crosshair indicating the center of the zoom-in area.
2. Use the
pointer button to position the crosshair.
3. Continue pressing the E-Zoom
area up to 4 times.
button to enlarge the selected
4. While the image is enlarged, you can:
■
Use the
pointer button to move around the screen.
■
Press the E-Zoom
button to zoom out.
5. When done, press the ESC button to return the image to its
original size.
Displaying a Picture-in-Picture Video
note
The Picture-in-Picture
function does not work for
RGB video images.
If you’re displaying an image from equipment connected to
the Computer port(s), you can open up a smaller picture-in-picture
window on the screen. This window can display video from
equipment connected to either the Video or S-Video port.
Setting Up the Picture-in-Picture Image
Before starting, make sure the computer or video equipment for your
main image is connected to the Computer port(s), and the video
equipment for the picture-in-picture window is connected to the
Video or S-Video port. Then select the corresponding video setting:
1. Press the Menu button on the remote control and enter the
Setting menu.
2. Highlight P in P Options and press Enter, then use the pointer
button to select Subscreen Image and press Enter. Use the
pointer to choose Video or S-Video, then press Enter.
3. Press Menu to exit the menu system.
38
Using the Remote Control
User's Guide.book Page 39 Tuesday, May 25, 2004 11:49 AM
Displaying the Picture-in-Picture Image
Make sure your main image source is displayed, then follow these
steps to display and use the picture-in-picture window:
1. Press the PinP button on the remote control.
2. Use the
pointer button to reposition the video window.
3. Once the window is the way you want it, press the Enter button;
your video continues playing on the screen.
Video window
PinP button
4. When you’re finished using picture-in-picture, press the PinP
or
pointer button again. The window disappears.
Controlling the Volume
To change the volume, press the
Volume button.
(quieter) or
(louder) side of the
note
You can also use the Volume
buttons on the projector to
adjust the volume.
To temporarily shut off the
sound and picture, press the
A/V Mute button.
If necessary, you can adjust the tone using the projector’s menu
system. See page 67.
Using the Remote Control 39
User's Guide.book Page 40 Tuesday, May 25, 2004 11:49 AM
Projecting Images Without a Screen
note
If the status message
indicates that Wall Shot is
off, press the Wall Shot
button again to turn it on.
Even if you don’t have a screen, you can project images onto surfaces
like blackboards and colored walls without loss of image color. Your
projector has a sensor that measures the conditions of the projection
surface and automatically adjusts the colors and shading of your
image. For example, if you’re projecting onto a surface near a window,
your image appears clear and bright rather than faint.
Making Initial Color Corrections
Press the Wall Shot button on either the remote control or the
projector’s control panel while projecting an image.
Wall Shot’s status appears in the upper right corner of your screen.
Then you see a sequence of colors flash for a couple of seconds while
the sensor measures the conditions of the projection surface and
adjusts the image.
The projector stores the correction values obtained by the last Wall
Shot measurements. This is useful if you’re projecting against the
same surface and under the same conditions. To retrieve these
corrections, repeatedly press the Wall Shot button until you see Wall
Shot Memory Call. This setting applies the stored Wall Shot values.
40
Using the Remote Control
User's Guide.book Page 41 Tuesday, May 25, 2004 11:49 AM
Adjusting Color Corrections for a New Surface
Adjust the correction values if you’re projecting on a new surface or in
a new location.
1. Press the Wall Shot button on the remote control or projector
while you’re projecting an image. Make sure Wall Shot is on.
2. Press the Wall Shot button a couple of times until you see Wall
Shot Readjustment as the status in the upper right corner of
your screen.
You see a sequence of colors flash for about five seconds as the
projector adjusts the color correction values for the new
projection surface.
Operating Your Computer with the
Remote Control
If you’ve connected a computer to the projector with a USB cable, as
described on page 49, you can use the remote control in place of your
computer’s mouse. This gives you more flexibility when delivering
slideshow-style presentations, since you won’t have to stand next to
the computer to change slides.
■
Use the Page buttons to move through a slideshow.
Page up or down
to change slides
in PowerPoint
Using the Remote Control 41
User's Guide.book Page 42 Tuesday, May 25, 2004 11:49 AM
■
Use the
pointer button to move the cursor on the screen.
■
Press the Enter button once to left-click, or press it twice to
double-click. Press the Esc button to right-click.
■
To drag-and-drop, hold down the Enter button for about one
second until it lights. Then use the
pointer button to drag the
object. When it’s where you want it, press Enter to release it.
Use to
move cursor
Left-click
42
Using the Remote Control
Right-click
User's Guide.book Page 43 Tuesday, May 25, 2004 11:49 AM
Highlighting Your Presentation
You can display a pointer to call out something on the screen, or draw
straight or curved lines to emphasize particular points. There are three
pointer tools you can choose from and each one can be customized for
a different look.
Using the Pointer Tool
1. To activate the pointer tool, press the Pointer button on the
remote control. A pointer appears on the screen.
Pointer
If you prefer to use a different style of pointer, see page 44 to
choose from three preset options.
2. Use the
pointer button on the remote control to position the
pointer on the screen.
3. When done using the pointer, press Esc to clear the screen.
Using the Remote Control 43
User's Guide.book Page 44 Tuesday, May 25, 2004 11:49 AM
Customizing the Pointer Tools
You can customize the shape and size of each of the three pointer
tools, and set how fast you can move the pointer across the screen.
1. Press the Menu button on the remote control, highlight the
Setting menu, highlight Pointer, and press Enter.
You can select one of the following pointer shapes:
2. Highlight Return and press Enter.
3. To change the size of the pointer, highlight Pointer Zoom and
press Enter.
4. Choose 100% or 200% and press Enter.
5. Highlight Return and press Enter.
6. To change the Pointer Speed setting, highlight Pointer Speed
and press Enter.
7. Highlight High Speed, Medium Speed, or Low Speed and
press Enter.
8. Highlight Return and press Enter.
9. Press Menu to exit from the menu system.
44
Using the Remote Control
User's Guide.book Page 45 Tuesday, May 25, 2004 11:49 AM
1
Connecting to Computers
and Other Equipment
T
his chapter tells you how to connect the projector to a notebook or
desktop computer, and/or to video equipment, such as a VCR or
DVD player. You can also connect the projector to a video camera,
external speakers, and/or an external monitor.
Follow the instructions in this chapter on:
■
Connecting to a computer
■
Connecting an external monitor
■
Connecting video equipment
■
Playing sound through the projector
45
User's Guide.book Page 46 Tuesday, May 25, 2004 11:49 AM
Connecting to a Computer
note
If you connect a Windowsbased computer to the
projector, you may see a
New Hardware Wizard
saying your computer has
found a plug-and-play
monitor; if so, click Cancel.
note
You can connect the PowerLite projector to any computer that has a
standard video output (monitor) port, including desktop models,
PC notebook and notebook computers, Macintosh PowerBooks and
iBooks®, and hand-held devices. You can connect up to two
computers at the same time. To connect to the
Computer/Component ports (standard VGA cable connection), see
page 47. After connecting to the computer, you may also want to:
■
connect a USB cable so you can use the remote control as a
mouse; see page 49
■
connect a monitor to the projector so you can view your
presentation close-up as well as on-screen (not necessary if you’re
using a notebook); see page 50
■
connect an audio cable to play computer audio; see page 56
For newer PowerBooks with
DVI connectors, see your
computer’s documentation
to see how to use a DVI to
VGA adapter (usually
included with the computer)
to connect to the VGA
Computer port.
If you’re using an older
Macintosh and you can’t
connect the cable to your
computer, you may need to
use the Macintosh desktop
adapter, as shown on
page 48 (available from
Epson; see page 13).
46
Connecting to Computers and Other Equipment
User's Guide.book Page 47 Tuesday, May 25, 2004 11:49 AM
Connecting to the Computer Ports
You can connect to either Computer/Component port using the
VGA computer cable that came with the projector (the monitor port
on your computer must be a mini D-sub 15-pin port).
1. If you’re using the VGA computer cable, connect one end to one
of the projector’s Computer/Component ports, and the other
end to your computer’s monitor port. Then go to step 4.
caution
Don’t try to force a
connector to fit a port with a
different shape or number of
pins. You may damage the
port or connector.
2. You can connect an optional stereo mini-jack audio cable to play
sound through the projector (see page 56), an external monitor
(see page 50), or a USB cable to use the remote control as a mouse
(see page 49).
3. When you’ve finished making any connections, see page 18 for
instructions on turning on the projector and adjusting the image.
Connecting to Computers and Other Equipment 47
User's Guide.book Page 48 Tuesday, May 25, 2004 11:49 AM
Using the Macintosh Desktop Adapter
If you have an older desktop Macintosh or PowerBook, the VGA
cable may not fit when you try to connect it. If so, you’ll need to use
the Macintosh desktop adapter to connect the VGA cable to your
computer. This is available from Epson (see page 13).
1. To use the adapter, remove its cover as shown and set its DIP
switches according to the resolution you want to use, such as
16-inch mode. See your Macintosh documentation for
instructions.
2. Replace the cover and connect the adapter
to the VGA cable. Then plug the cable
(with the adapter) into the video port on
your Macintosh.
3. Tighten the screws on the connectors.
48
Connecting to Computers and Other Equipment
User's Guide.book Page 49 Tuesday, May 25, 2004 11:49 AM
Connecting the Cable for Remote Mouse
Control
If you’ve connected a computer as described in this chapter, you
can use the projector’s remote control as a wireless mouse. This lets
you control your computer and click through slideshow-style
presentations, such as PowerPoint, from up to 33 feet away.
The wireless mouse function is supported on systems with a USB port
running Windows XP, 98, Me, or 2000, or Macintosh OS X 10.2.x to
10.3.x or OS 8.6 to OS 9.x.
1. Locate the USB cable that came with your projector.
2. Connect the square end of the cable to the projector’s
USB port.
note
The remote mouse control
function may not operate
correctly on systems that
have been upgraded from an
earlier version of Windows.
note
For details on using the
remote control in place of
your computer’s mouse, see
page 41.
USB cable
Use to move
cursor
3. Connect the flat end of the cable to any available USB port on
your notebook or desktop computer.
4. If necessary, configure your computer to work with an external
USB mouse. See your computer documentation for details.
Left-click
Right-click
Connecting to Computers and Other Equipment 49
User's Guide.book Page 50 Tuesday, May 25, 2004 11:49 AM
Connecting an External Monitor
If you want to monitor your presentation close-up (on a monitor
placed beside the projector) as well as on the screen, you can connect
an external monitor.
To attach an external monitor, connect it to the projector’s Monitor
Out port, as shown:
External monitor
Follow these guidelines to view images on the monitor:
50
■
The monitor displays the currently selected computer source.
Press the Preview button on the remote control if you want to
display all the active sources at the same time (see page 35).
■
You can also view images on the monitor while the projector is in
Standby mode, if you’ve set Network ON in the Extended menu
(see page 75).
Connecting to Computers and Other Equipment
User's Guide.book Page 51 Tuesday, May 25, 2004 11:49 AM
Connecting to Video Equipment
You can connect up to four video sources to the projector at the same
time. Before starting, look at your video equipment to determine its
available video output connections:
■
If your video player has a yellow RCA-style video output
connector, see “Connecting a Composite Video Source” on
page 52.
■
If your video player has an S-Video connector, see “Connecting
an S-Video Source” on page 53.
■
If your video player has a component video port (three connectors
labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a
Component Video Source” on page 54.
■
RCA connector
(composite video)
S-Video
connector
VGA connector
(RGB video)
If your video player has an RGB video port (either a single
connector for a VGA-style monitor cable or three connectors
labeled R/G/B), see “Connecting an RGB Video Source” on
page 55.
After connecting video cables, you may also want to:
■
Connect a monitor to the projector so you can view your
presentation close-up as well as on-screen; see page 50.
■
Connect an audio cable to play sound through the projector; see
page 56.
Connecting to Computers and Other Equipment 51
User's Guide.book Page 52 Tuesday, May 25, 2004 11:49 AM
Connecting a Composite Video Source
1. Locate the RCA-style video cable provided with the projector.
2. Connect the cable to the yellow video output connector on your
player and the yellow Video connector on the projector:
3. If you want to play sound through the projector, see page 56 for
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see page 18 or
the Quick Setup sheet for instructions on turning on the projector
and adjusting the image. Once the projector is turned on, select
the image source: press the Search button on the remote control
or press the Source Search button on the projector’s control
panel repeatedly until the image appears.
52
Connecting to Computers and Other Equipment
User's Guide.book Page 53 Tuesday, May 25, 2004 11:49 AM
Connecting an S-Video Source
1. Locate an S-Video cable (one is usually provided with your video
equipment or you can purchase one from Epson; see page 12).
2. Connect the cable to the S-Video connector on your player and
the S-Video connector on the projector:
3. If you want to play sound through the projector, see page 56 for
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see page 18 or
the Quick Setup sheet for instructions on turning on the projector
and adjusting the image. Once the projector is turned on, select
the image source: press the Search button on the remote control
or press the Source Search button on the projector’s control
panel repeatedly until the image appears.
Connecting to Computers and Other Equipment 53
User's Guide.book Page 54 Tuesday, May 25, 2004 11:49 AM
Connecting a Component Video Source
1. Locate a component-to-VGA video cable.
note
2. Connect the cable to your player and one of the
Computer/Component connectors on the projector.
Be sure your video player is
not an RGB video source.
If you select the wrong
source, image quality may
suffer. Check your video
player’s documentation.
3. If you want to play sound through the projector, see page 56 for
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see page 18 for
instructions on turning on the projector and adjusting the image.
Once the projector is turned on, select the image source: press the
Search button on the remote control or press the Source
Search button on the projector’s control panel repeatedly until
the image appears.
54
Connecting to Computers and Other Equipment
User's Guide.book Page 55 Tuesday, May 25, 2004 11:49 AM
Connecting an RGB Video Source
1. Locate the VGA computer cable provided with the projector.
2. Connect the cable to the video port on your player and one of
the Computer/Component ports on the projector.
note
Be sure your video player is
not a component video
source. If you select the
wrong source, image quality
may suffer. Check your
video player’s
documentation.
3. If you want to play sound through the projector, see page 56 for
instructions on connecting an audio cable.
4. If you don’t need to make any other connections, see page 18 for
instructions on turning on the projector and adjusting the image.
Once the projector is turned on, select the image source: press the
Search button on the remote control or press the Source
Search button on the projector’s control panel repeatedly until
the image appears.
Connecting to Computers and Other Equipment 55
User's Guide.book Page 56 Tuesday, May 25, 2004 11:49 AM
Playing Sound Through the Projector
You can play sound through the projector’s speaker system or attach
an external speaker system. Attaching speakers to the projector instead
of directly to the audio source lets you use the projector’s remote
control to adjust the sound.
Connecting Audio Equipment to the Projector
To play sound through the projector, follow these steps:
1. Locate the appropriate commercially available audio cable.Which
cable you use depends on how your equipment is connected:
■
If you have a computer connected to a
Computer/Component port, use a stereo mini-jack cable.
■
If you have video equipment connected to the Video or
S-Video port, use an RCA-style audio cable.
2. Connect the audio cable to the jack corresponding to the
connected video source.
Use with Computer or
Component connection
Use with
Video
connection
Use with
S-Video
connection
3. Connect the other end of the cable to the audio output connector
on your computer or video equipment.
56
Connecting to Computers and Other Equipment
User's Guide.book Page 57 Tuesday, May 25, 2004 11:49 AM
Connecting External Speakers
To connect speakers to the projector, follow these steps:
1. Locate the appropriate cable to connect your speakers.
Depending on your speakers you may be able to use a
commercially available audio cable with a stereo mini-jack
connector on one end and pin jacks on the other end. For some
speakers, you may have to purchase a special cable or use an
adapter.
2. Connect the stereo mini-jack end of the audio cable to the Audio
Out port on the projector.
3. Connect the other end(s) of the cable to your speakers.
The projector’s internal speaker system is disabled while sound is
output to external speakers.
Connecting to Computers and Other Equipment 57
User's Guide.book Page 58 Tuesday, May 25, 2004 11:49 AM
58
Connecting to Computers and Other Equipment
User's Guide.book Page 59 Tuesday, May 25, 2004 11:49 AM
1
Fine-Tuning the Projector
Y
ou can use the projector’s on-screen menus to adjust the image,
sound, and other features. This chapter covers the following
information:
■
Using the menu system
■
Adjusting the image quality
■
Adjusting the image size, shape, and position
■
Adjusting the color
■
Adjusting the sound
■
Using the projector security features
■
Controlling multiple projectors
■
Customizing projector features
■
Enabling Quick Setup options
59
User's Guide.book Page 60 Tuesday, May 25, 2004 11:49 AM
Using the Menu System
You can use the remote control or the projector’s control panel to
access the menus and change settings. Follow these steps:
1. To display the menu screen, press the Menu button.
You see a menu screen similar to the one below:
Options
Menu list
The menus are listed on the left and the options available for the
highlighted menu are shown on the right.
2. Use the
pointer button on the remote control (or the arrow
buttons on the projector) to scroll through the menu list. When
you’ve highlighted the desired menu, press the Enter button to
select it.
3. Once you’ve selected the menu, use the
pointer button to
scroll through the list of options. (Some of the options may be
grayed out or unavailable, depending on the selected source.)
4. After highlighting the option you want to adjust, use the
pointer button to change the setting. In some cases, you may
have to press the Enter button to view a sub-screen for changing
the setting.
+
-
ON
60
OFF
Fine-Tuning the Projector
■
Press the left or right side of the
a slider bar.
pointer button to adjust
■
To select from two or more settings, use the
pointer
button to highlight the desired setting and press Enter.
User's Guide.book Page 61 Tuesday, May 25, 2004 11:49 AM
5. After changing the settings, press the Esc button to save your
changes and return to the previous menu (or press it repeatedly to
exit the menu system).
You can also press the Menu button to exit.
Restoring the Default Settings
You can use the menu system’s Reset options to restore the factorydefault settings for all the settings listed in a specific menu, or all the
settings in all menus.
To restore the settings in a specific menu, enter the menu whose
settings you want to change, select Reset, and confirm as needed.
(The example below shows how to reset the Settings menu.)
Reset settings
for current menu
Reset settings for
all menus
To restore all the projector settings to their factory-default values,
select the Reset menu, highlight All Reset, and press Enter.
note
When you select All Reset
in the Reset menu, it does
not reset the Computer
Input, User’s Logo,
Language, Projector ID,
Network, and Lamp
settings.
Fine-Tuning the Projector 61
User's Guide.book Page 62 Tuesday, May 25, 2004 11:49 AM
Adjusting the Image Quality
You can use the Video menu to adjust the brightness, sharpness, color,
tint, and contrast. If you’re projecting from a computer, there are
additional adjustments you can make (see page 63).
Adjusting the Image
1. Press the Menu button on the remote control and select the
Image menu. You see the Image menu screen.
2. Use the
pointer button to highlight the desired option, then
adjust it as needed:
■
Color Mode
Lets you quickly adjust the color and brightness for various
environments. Use either the remote control or the Color
Mode setting in the Image menu. You can save a different
setting for each computer and/or video source. Select from
these settings:
Dynamic: For projecting movies or playing video games in
vivid color in a bright room.
Presentation: For presentations in dark rooms.
Theatre: For optimizing movie images with natural color in a
dark room (the default for video or S-Video display).
Living Room: For playing video games and watching TV in
a bright room.
62
Fine-Tuning the Projector
User's Guide.book Page 63 Tuesday, May 25, 2004 11:49 AM
sRGB: For standard sRGB computer displays (the default
when projecting from a computer with analog video).
■
Brightness
Lightens or darkens the overall image.
■
Contrast
Adjusts the difference between light and dark areas.
■
Sharpness
Adjusts the sharpness of the image.
■
note
The Brightness setting
changes the opacity of the
projector’s LCD panels. You
can also change the lamp’s
brightness. Select
Brightness Control in the
Setting menu, then choose
High or Low (the default
setting is High).
Color Adjustment
Adjusts the tint of the image (not available for RGB video
images).
Adjusting Signal Settings
Although the projector normally detects and optimizes the input
signal automatically, you can use the Signal menu to make manual
adjustments. In addition to changing the position of the projected
image, you can correct tracking and sync for computer images, or
change the aspect ratio to widescreen format for video images.
1. Press the Menu button on the remote control and select the
Signal menu.
You see a screen similar to the one below. (The settings will be
different depending on the source you are projecting from.)
note
You can also use the remote
control’s Auto button to
automatically reset the
projector’s tracking, sync,
resolution, and position
settings. See page 28 for
details.
Fine-Tuning the Projector 63
User's Guide.book Page 64 Tuesday, May 25, 2004 11:49 AM
2. Use the
pointer button to highlight the desired option, then
adjust it as needed:
■
Auto Setup
Leave this setting ON to automatically optimize the computer
image. Turn it off if you want to save adjustments you have
made to the video settings.
■
If your image is distorted (compressed, stretched, partially cut
off, or doesn’t completely fill the display area), the projector’s
resolution setting may not match that of your computer.
Select Auto to let the projector adjust the resolution
automatically, or Manual to adjust the setting yourself. (Press
Enter after you make the selection.)
tip
Before adjusting tracking or
sync, fill the screen with an
image containing fine
detail. For example, in
Windows you can select a
pattern to appear as your
desktop background. If this
option isn’t available, try
projecting black text on a
white background.
Resolution
■
Tracking
Adjust this value to eliminate vertical stripes in the image.
■
Sync
Adjust this value if the image appears blurry or flickers.
■
Position
If the image is slightly cut off on one or more sides, it may not
be centered exactly. Select this setting and use the
pointer
button to center it.
■
Preset
button
Preset
Once you’ve fine-tuned the settings in the Signal menu for
the computer you’re using, you can save them as a group
using one of the ten Preset settings. The next time you use
the same computer, simply press the Preset button on the
remote control to recall your saved settings. (Press the Preset
button repeatedly to select the number corresponding to the
setting you want to use.)
■
Computer 1 Input/Computer 2 Input
If the colors don’t look right on the Auto setting, select the
setting for the type of equipment you’ve connected to the
Computer/Component port(s):
RGB: For a computer connection.
64
Fine-Tuning the Projector
User's Guide.book Page 65 Tuesday, May 25, 2004 11:49 AM
Component Video: For a video player that outputs a
component video signal.
■
Video Signal
Leave this setting at Auto unless you are using a 60-Hz PAL
system (select PAL60).
Adjusting the Image Size, Shape, and
Position
Whether you’re projecting from a computer or video player, you can
use these settings to adjust the size, shape, and position of the image.
■
Resize button
Adjusts how an image fits into the display area.
For computer images, resizing is normally unnecessary, since the
projector automatically resizes the image to make the best use of
the display area. If you press the Resize button on the projector
or remote control, the projector displays the image at the output
resolution of the computer (which makes the image larger or
smaller, depending on its resolution). If the resolution of the
image is the same as the projector’s (1024 × 768), pressing Resize
has no effect.
For video images, pressing Resize switches the aspect ratio
between 4:3 and 16:9. This lets you play certain digital video
images or movies recorded on certain DVDs in 16:9 widescreen
format.
■
note
If your computer image is
stretched, compressed, or
doesn’t fit correctly on the
screen, try adjusting the
Resolution setting first (see
page 64).
Keystone (in the Setting menu)
Squares up the shape of the image after the projector has been
tilted upward or angled to one side (see page 26). If you notice
lines or edges looking jagged after adjusting the shape, decrease
the Sharpness setting (see page 62).
■
Position (in the Signal menu)
If the image is slightly cut off on one or more sides, it may not be
centered exactly. Select this setting and use the
pointer button
to center it (not available for digital RGB or RGB video images).
Fine-Tuning the Projector 65
User's Guide.book Page 66 Tuesday, May 25, 2004 11:49 AM
Adjusting the Color
The projector provides several ways for you to adjust the color:
■
Color Mode button (also in the Image menu)
Lets you quickly adjust the color and brightness for various
environments. Use either the remote control or the Color Mode
setting in the Image menu. You can save a different setting for
each computer and/or video source. Select from these settings:
■
Dynamic: For projecting movies or playing video games in
vivid color in a bright room.
■
Presentation: For presentations in dark rooms.
■
Theatre: For optimizing movie images with natural color in a
dark room (the default for video or S-Video display).
■
Living Room: For playing video games and watching TV in
a bright room.
■
sRGB: For standard sRGB computer displays (the default
when projecting from a computer with analog video).
■
66
Fine-Tuning the Projector
Color Adjustment (in the Setting menu)
Adjusts the color temperature. Select Color Temp. to set a
temperature between 5000 and 10000 °K. Or select RGB to
adjust individual red, green, and blue values. (Not available if
sRGB is selected as the Color Mode setting.)
User's Guide.book Page 67 Tuesday, May 25, 2004 11:49 AM
Adjusting the Sound
You can use the Audio settings to adjust the sound volume or tone.
note
1. Press the Menu button on the remote control and select the
Setting menu.
You can also adjust the
volume using the remote
control.
2. Choose Audio and press Enter.
You see the Audio menu settings:
3. Use the
pointer button to highlight the desired option, then
adjust it as needed:
■
Volume
Adjusts the volume.
■
Tone
Adjusts the quality of the sound.
Using the Projector Security Features
To prevent unauthorized use of the projector, you can do the
following:
■
Assign a password; this can be disabled for a set period if you want
to loan the projector to someone. See page 68.
■
Create an identifying user logo that is displayed at startup and/or
when the A/V Mute button is pressed. See page 71.
■
Disable the projector’s buttons; this is useful, for example, if
you’re projecting in a classroom and you want to ensure that no
one touches the projector’s buttons while you’re using the remote
control. See page 72.
Fine-Tuning the Projector 67
User's Guide.book Page 68 Tuesday, May 25, 2004 11:49 AM
If you create a user’s logo for the projector, you can set up the logo so
it is displayed as the startup screen and/or AV/Mute screen.
Unauthorized users cannot turn it off or change it. This feature is
intended to discourage theft and provides a way to identify the
projector should it be stolen.
Enabling Password Protection
note
It’s a good idea to write
down your password.
If you leave the projector
plugged in, the Password
Protect Release screen will
not appear. You only need a
password if you unplug and
reconnect the power cable.
To prevent unauthorized use, you can assign the projector a password.
If you do, a screen will appear requesting the password whenever the
projector is plugged in and turned on. If an incorrect password is
entered three times in succession, the projector’s operation is locked
and the power cord must be disconnected and reinserted to redisplay
the password screen. If an incorrect password is entered thirty times in
succession, the user must contact Epson to unlock the projector.
The default setting for the Password Protect function is OFF. Follow
these steps to turn password protection on:
1. Press the Freeze button on the remote control for about five
seconds.
You see this screen:
caution
If you lose the remote
control, you will not be able
to enter the password. Keep
the remote control in a safe
place at all times.
2. Use the
pointer button to set Power ON Protect to ON. Then
press Enter.
3. Select Password and press Enter.
4. When you see a message asking if you want to change the
password, select Yes and press Enter.
68
Fine-Tuning the Projector
User's Guide.book Page 69 Tuesday, May 25, 2004 11:49 AM
5. Press the Num button on the remote control. When it lights, the
numeric keypad is activated.
6. Use the numeric keypad to enter a four digit password. (The
default setting is 0000.)
7. When you see a confirmation message, reenter the password.
Then press the Menu button to exit the screen.
8. Press the Num button on the remote control to deactivate the
numeric keypad.
9. If you want to disable the password temporarily, select Timer and
press Enter. Then hold down the Num button while you use the
numeric keypad to enter the number of hours (from 0 to 9999)
that you want the password feature disabled. If you want the
projector to request the password every time it is turned on, set
the timer to 0H.
The countdown for the elapsed time begins as soon as you close
the Password Protect menu. (You can check the elapsed time in
this menu next to Time elapsed.)
10. To enable your screen logo, select User’s Logo Protect and press
Enter. Select ON and press Enter.
When this feature is on, the logo appears whenever you turn on
the projector (if the Startup Screen is enabled in the Extended
menu; see page 71). It also appears when you press the A/V Mute
button (if you selected the Logo as the Background Color in the
Extended menu). None of the User’s Logo features in the
Extended menu can be changed when the User’s Logo Protect
function is enabled.
Fine-Tuning the Projector 69
User's Guide.book Page 70 Tuesday, May 25, 2004 11:49 AM
Starting the Projector with a Password
When the password function is enabled, you see this screen when you
plug in and turn on the projector:
1. Press the Num button on the remote control to activate the
numeric keypad.
2. Enter the four digit password.
The password screen closes, the numeric keypad is automatically
deactivated, and projection begins.
If the password is not correct, you see the message Wrong password.
Please try again. If you enter an incorrect password three times in
succession, you see the message The projector’s operation will be
locked. Request code xxxxx and the projector switches to standby
mode for approximately 5 minutes. Write down the request code.
Then disconnect the projector’s power cord from the electrical outlet,
reconnect it, and turn the projector back on.
When you see the Password Protect Release screen again, you can try
to enter the correct password.
If you have forgotten the password, contact Epson with the request
code number that appears in the Password Protect Release screen for
assistance. See “Where To Get Help” on page 112.
If you enter an incorrect password 30 times in succession, the
projector remains locked and you must contact Epson to unlock it.
70
Fine-Tuning the Projector
User's Guide.book Page 71 Tuesday, May 25, 2004 11:49 AM
Creating Your Own Startup Screen
You can transfer any image from your computer or video source to the
projector and then use it as your startup screen. You can also use it as
the screen displayed when the projector is not receiving a signal or
when you press the A/V Mute button. The image can be a company
logo, slogan, photograph, or any other image you want to use.
Capturing the Image
Start by displaying the image you want to use from either a computer
or video source, such as a DVD player. Then follow these steps to
capture the image and transfer it to the projector:
1. Press the Menu button on the remote control, highlight the
Extended menu, and press Enter.
2. Highlight User’s Logo and press Enter.
3. When you see a message asking whether you accept the present
image as the user’s logo, select Yes and press Enter. A selection
box displays over the image.
4. Use the
pointer button to select the area of the image you
want to use. Then press Enter.
5. When you see the message Select this Image?, highlight Yes
and press Enter.
6. Use the arrow buttons to select a zoom rate (display size) and press
Enter.
Fine-Tuning the Projector 71
User's Guide.book Page 72 Tuesday, May 25, 2004 11:49 AM
7. When the message Save image as user’s logo? appears, select
Yes and press Enter. Saving the logo may take a few moments.
Do not use your projector or video source while the logo is being
saved.
8. When you see the message Completed, press Esc to return to the
menu screen.
Choosing When to Display the Image
After your image is saved, it is automatically set as the startup screen.
You can also save it as the screen you see when there’s no signal or
when you press the A/V Mute button (see page 37).
1. Press the Menu button, highlight the Extended menu, and press
Enter.
2. Select Display and press Enter.
3. Select the screen(s) on which you want your image to appear:
■
Highlight Display Background to display your image
(instead of a blank screen) when there is no video signal
coming from the currently selected source. Then press Enter.
■
Highlight A/V Mute to display your image when you press
the A/V Mute button. Then press Enter.
4. Select Logo and press Enter.
5. When you’re finished, press Esc to exit.
Disabling the Projector’s Buttons
When you enable the Operation Lock function, you can lock all the
projector’s buttons, or you can lock some of the projector’s buttons.
1. Press the Menu button, highlight the Setting menu, and press
Enter.
2. Select Operation Lock and press the Enter button.
3. Select Full Lock or Partial Lock and press Enter.
4. Select Yes and press Enter to confirm the setting.
5. Press the Menu button to exit.
72
Fine-Tuning the Projector
User's Guide.book Page 73 Tuesday, May 25, 2004 11:49 AM
Controlling Multiple Projectors
If you’re using more than one projector for your presentation, you can
switch between them using a single remote control. To do this, you
need to set a different ID for each projector. During the presentation,
you can change the remote control’s ID to match that of the projector
you want to use.
Setting the Projector ID
The projector’s default ID is 1. Follow these steps to change it:
1. Press the Menu button on the remote control.
You see the projector’s menu screen.
note
By default, the remote
control’s ID is set to zero,
which allows it to control
any projector. If you want to
control multiple projectors
simultaneously, and you
don’t want to switch
between them (each
projector would need its own
screen), you can leave the
remote control’s ID set to
zero.
2. Select the Extended menu and press Enter.
3. Highlight Projector ID and press Enter.
4. Choose an ID value for the projector and press Enter.
5. When you’re done, press Esc to exit the menu system.
Fine-Tuning the Projector 73
User's Guide.book Page 74 Tuesday, May 25, 2004 11:49 AM
Changing the Remote Control ID
To change the remote control’s ID to match the projector’s ID, follow
these steps:
1. Press the ID button on the remote control. You see it light.
2. Press one of the numbered buttons on the remote control to select
the ID of the projector you want to operate.
The ID button’s light shuts off and the new ID is registered.
3. Repeat steps 1 and 2 each time you want to switch projectors.
To check the remote control’s current ID, do the following:
1. Press the ID button twice. After a moment, the button flashes.
2. Count the number of flashes; this number corresponds to the
remote control’s ID. (If it doesn’t flash, the ID is set to zero.)
74
Fine-Tuning the Projector
User's Guide.book Page 75 Tuesday, May 25, 2004 11:49 AM
Customizing Projector Features
You can use the menu system to turn standby mode on or off, adjust
the network settings, change the language, and customize the way the
projector displays images.
Remote Monitoring Setup Options
These options let you set up the projector so it can be monitored and
controlled from a remote computer (see page 80).
■
Standby Mode (in the Extended menu)
Select Network ON to enable the projector to be monitored over
a network when it’s in standby mode.
■
note
When Standby Mode is set
to Network ON, the
exhaust fan continues to
operate after the projector
has cooled down. This is
normal.
If you want to monitor the projector using a network
management utility, select SNMP in the Network menu and
enter at least one trap IP address.
Miscellaneous Setup Options
■
Projection (in the Extended menu)
Select Front (to project from the front of a screen and right side
up), Front/Ceiling (when the projector is mounted upside-down
from the ceiling), Rear (to project from behind onto a
transparent screen), or Rear/Ceiling (to project from behind onto
a transparent screen when the projector is mounted upside-down
from the ceiling).
■
Language (in the Extended menu)
Select from nine languages to be used for the projector menus.
Fine-Tuning the Projector 75
User's Guide.book Page 76 Tuesday, May 25, 2004 11:49 AM
Enabling Quick Setup Options
Your projector can quickly detect and set up the focus, straighten the
image, and adjust the colors for the surface the image is being
projected on. Follow these steps to enable these features:
1. Press the Menu button on the remote control.
You see the projector’s menu screen.
2. Select the Setting menu and press Enter. Then highlight Quick
Setup and press Enter.
3. Select Quick Setup Options and press Enter.
4. Adjust any of these options:
■
Highlight Auto Focus to automatically focus the projector.
■
Highlight Auto Quick Corner to automatically straighten
the image if it is not rectangular.
■
Highlight Wall Shot to project on walls or surfaces that are
not white.
5. Press Enter, then highlight ON or OFF and press enter. Highlight
Return and press Enter.
6. When you are done adjusting settings, press the Menu button to
exit.
76
Fine-Tuning the Projector
User's Guide.book Page 77 Tuesday, May 25, 2004 11:49 AM
Automatically Running Quick Setup
To automatically run quick setup whenever you turn on the projector,
follow these steps:
1. Press the Menu button on the remote control.
You see the projector’s menu screen.
2. Select the Setting menu and press Enter. Then select Quick
Setup and press Enter.
3. Select Startup Options and press Enter.
4. Select Quick Setup and press Enter.
5. Press the Menu button to exit.
Fine-Tuning the Projector 77
User's Guide.book Page 78 Tuesday, May 25, 2004 11:49 AM
78
Fine-Tuning the Projector
User's Guide.book Page 79 Tuesday, May 25, 2004 11:49 AM
1
Managing Projectors
T
he EasyManagement software for your projector lets you monitor
and control your projectors from a remote computer:
■
Use EMP Monitor (available for Windows only) to see your
projectors’ status, switch image sources, and control basic settings.
■
Use EMP NetworkManager to send out messages by e-mail,
notifying you when a problem occurs with a projector.
■
Use a network management utility running SNMP, such as
HP OpenView, to manage your facility’s equipment from a
pre-existing system.
note
If you’re using a network
management utility running
SNMP, you can configure
your network to send trap
alerts even without a plug-in
(see page 80). This feature is
intended for use by network
administrators only.
To use the EasyManagement software to manage your projectors, first
install EMP Monitor as described on page 114. Then connect and
configure each projector you want to monitor. You can connect the
projector over a wired network (as described on page 80).
This chapter covers the following information:
■
Connecting the projector to and configuring it for a wired
network
■
Monitoring and controlling your projector with EMP Monitor
■
Using a browser to monitor the projector
79
User's Guide.book Page 80 Tuesday, May 25, 2004 11:49 AM
Connecting and Configuring the
Projector on a Wired Network
note
If you’re a network
administrator, you can use
the SNMP option to enter a
trap IP address. This lets you
receive trap alerts for the
projectors you’re monitoring.
Before using the EasyManagement software to manage your
projector(s), you have to connect each projector you want to monitor
to your network and configure it with an appropriate IP address. You
can connect and configure the projector using the network port.
Follow these steps to connect and configure the projector for your
network.
1. Connect the projector to your network using a commercially
available 100baseTX or 10baseT network cable.
2. Turn on the projector (see page 18).
3. Press the Menu button on the remote control and select Network
from the Extended menu.
4. If your network assigns addresses automatically, turn on DHCP.
If your network does not assign addresses automatically, turn off
DHCP and enter the projector’s IP Address, Subnet Mask, and
Gateway Address, as needed.
■
80
Managing Projectors
To enter numbers using the remote control, press the Num
button until it lights, then use the number keypad shown
below.
User's Guide.book Page 81 Tuesday, May 25, 2004 11:49 AM
■
To change the network addresses from the projector’s control
panel, press the right and left arrow buttons to select the part
of the address you want to enter, then use the up and down
arrow buttons to increase or decrease the numeric value.
Select the
part of the
address to
change
Increase
or
decrease
the value
When you finish changing an address in the network menu, press
the Enter button (on the remote control) or the Auto/Enter
button (on the projector).
5. When you’re done, press Esc to exit the menu system.
Using EMP Monitor
EMP Monitor lets you use a remote computer to manage your
projectors over a wired network. It lets you easily turn the projectors
on or off (together or individually), switch image sources, and check
their status.
Before using EMP Monitor, make sure you’ve installed the software
(available for Windows only) as described on page 114. The
computer you’re using to monitor the projector should already
be connected to your network.
note
If you want to monitor
projectors while they are in
standby mode, select
Standby Mode in the
Extended menu, then select
Network ON. See page 75.
Managing Projectors 81
User's Guide.book Page 82 Tuesday, May 25, 2004 11:49 AM
Opening and Closing EMP Monitor
To start EMP Monitor, click Start > Programs or All Programs >
Epson Projector > EMP Monitor.
If you’ve added the program to the Startup programs folder, then it
may already be open. If so, click the icon in the system tray on the
lower-right corner of your screen to display the EMP Monitor
window:
Click here to start EMP Monitor
To close EMP Monitor, right-click the program icon shown above
and select Exit.
Registering Your Projectors
Before you can monitor your projectors, follow these steps to register
them:
1. Click Start > Programs or All Programs > Epson Projector >
EMP Monitor or click the EMP Monitor icon in the taskbar. You
see this screen:
Click here
82
Managing Projectors
User's Guide.book Page 83 Tuesday, May 25, 2004 11:49 AM
2. Click Register projector. You see this screen:
Click here
note
3. Click Auto detect to locate projectors currently operating on the
network. Or click Manual registration and enter the projector’s
network IP address.
If Auto detect fails to find
the projector, your projector
may not be connected or
configured correctly for the
network. See page 80 to
configure your projector for
a wired network.
Any projectors found on the network are listed as shown below:
Click here
4. Select each projector you want to add by clicking its name, then
clicking the Add button. When you’re done, click Close.
Managing Projectors 83
User's Guide.book Page 84 Tuesday, May 25, 2004 11:49 AM
You see this screen with a list of all registered projectors.
note
To delete a projector from
the list, highlight the
projector name, and click
Delete.
5. Click Close.
You see the status of each of your registered projectors on the main
EMP Monitor screen:
84
Managing Projectors
User's Guide.book Page 85 Tuesday, May 25, 2004 11:49 AM
Monitoring Your Projectors
The EMP Monitor screen lets you monitor your projectors using the
Status, Video Source, and Error icons shown below. These let you see
which projectors are currently being used, from which source (or port)
they are projecting an image, and if a problem occurs.
note
To monitor a projector
when it’s in standby mode
(plugged in but not turned
on), you must select
Network ON as the
Standby Mode setting in
the projector’s Extended
menu (see page 75).
Remember that when
Standby Mode is set to
Network ON, the exhaust
fan continues to operate
after the projector has cooled
down. This is normal.
Status icon
Video Source
icon
Error icon
For detailed status information, select the projector and click View
details.
The following table explains the meaning of the status icons:
Status icons
(green)
Projecting; no problems
(dark)
Turned off; no problems
(green)
Projecting; problems detected
Managing Projectors 85
User's Guide.book Page 86 Tuesday, May 25, 2004 11:49 AM
Status icons
(dark)
Turned off; problems detected
Network error (for example, not connected to the
network or power cable disconnected).
You may also see this error if Network OFF is
selected in Standby Mode (see page 75).
The following table explains the meaning of the video source icons:
Video source icons
Computer/Component 1
Computer/Component 2
S-Video
Video
EasyMP (Not functional for the PowerLite 830p)
86
Managing Projectors
User's Guide.book Page 87 Tuesday, May 25, 2004 11:49 AM
The following table explains the meaning of the error icons. See
page 101 for recommended solutions to problems.
Error icons
Lamp replacement notification (the lamp is nearing
the end of its life; see page 97)
High-speed cooling in progress (the projector is
getting too hot but continues to operate)
Overheating (projection turned off automatically)
Lamp out or lamp cover open
Fan error
Sensor error
Internal problem
note
Controlling Your Projectors
The control buttons in the upper-right let you select video signals and
turn projectors on or off. (Hold the mouse pointer over a button to
see a description of its function.) Select the projector you want to
operate (with the mouse pointer) before clicking one of the buttons.
Control
buttons
To turn on a projector when
it’s in standby mode
(plugged in but not
projecting), you must have
selected Network ON as the
Standby Mode setting in
the projector’s Extended
menu (see page 75).
Remember that when
Standby Mode is set to
Network ON, the exhaust
fan continues to operate
after the projector has cooled
down. This is normal.
Managing Projectors 87
User's Guide.book Page 88 Tuesday, May 25, 2004 11:49 AM
The following table explains the functions of the control buttons:
Control buttons
Turns the projector on
Turns the projector off
Changes the video signal to the
Computer/Component 1 port
Changes the video signal to the
Computer/Component 2 port
Changes the video signal to the S-Video port
Changes the video signal to the Video port
Switches the display to EasyMP (Not functional for the
PowerLite 830p)
88
Managing Projectors
User's Guide.book Page 89 Tuesday, May 25, 2004 11:49 AM
Using EMP NetworkManager
You can use EMP NetworkManager to send out messages by e-mail,
notifying you when a problem occurs with a projector. Before running
EMP NetworkManager, make sure you’ve installed the software as
described on page 114. Then follow the steps below to create e-mail
settings for each projector you want to monitor.
Selecting the Projectors to Monitor
1. To start EMP NetworkManager, click Start > Programs or
All Programs > EPSON Projector > EMP NetworkManager.
You see the EMP NetworkManager screen. The projectors you’ve
already registered through EMP Monitor appear as icons.
2. If you’d like to register a projector manually and you know its IP
Projector address selection icon.
address, double-click the
You see this screen:
3. Enter the projector’s IP address and click Add. The projector’s
icon is added to the EMP NetworkManager screen.
Managing Projectors 89
User's Guide.book Page 90 Tuesday, May 25, 2004 11:49 AM
Setting a Password
note
Entering a password in
EMP NetworkManager will
automatically assign that
password in EMP Monitor.
You can set a password to restrict access to each projector from EMP
NetworkManager:
1. Right-click the icon of the projector whose password you want to
set, then select Change Password.
2. Enter a password up to 14 characters in length.
Creating the E-Mail Settings
1. If EMP NetworkManager is not already running, open it from
the Start menu. You see your registered projectors displayed as
shown:
2. Double-click the icon for the projector whose e-mail settings you
want to create. Enter your password, if you created one (see
above).
90
Managing Projectors
User's Guide.book Page 91 Tuesday, May 25, 2004 11:49 AM
3. EMP NetworkManager connects to the projector, and you see
this screen:
note
The projector must be
plugged in (projecting or in
standby mode) for you to be
able to connect to it.
To access a projector in
standby mode, you must
select Network ON as the
Standby Mode setting in
the projector’s menu system
(see page 75).
Remember that when
Standby Mode is set to
Network ON, the exhaust
fan continues to operate
after the projector has cooled
down. This is normal.
4. Verify that the network settings are correct. (If DHCP is on, you
don’t need to verify network settings.)
■
Make any desired changes to the projector’s network address
configuration (turning off DHCP enables the manual
settings).
■
You can give the projector a name—up to 15 characters long,
including the following symbols: ! @ # $ % ^ & ' . - _ { } ~
Naming the projector helps you identify it in EMP Monitor
and EMP NetworkManager, especially if you’re managing
more than a few of them.
5. Click Mail Notification Settings.
Managing Projectors 91
User's Guide.book Page 92 Tuesday, May 25, 2004 11:49 AM
You see this screen:
6. Select ON for the Mail Notification setting.
7. Enter the IP address and port number of the SMTP server used
for sending e-mail. (The port’s default setting is 25, but you can
enter any number from 1 to 65535.)
8. Enter up to three e-mail addresses where you want the event
notification messages to be sent.
note
A no-signal message is
reported when no image
signals are being input to a
projector. If the projector
will not normally be
displaying an image, do not
select “no signal” as a
condition for which you
want a message to be sent.
9. Click the Setting a Notification Event button next to each
address, then select the conditions under which you want a
message to be sent.
10. Click OK, then click OK again on the next screen. Click Set on
the Setup for Network Projector screen and confirm as needed.
11. When you see the test message window, you can send a message
with the heading “TEST MAIL” to the addresses you have
entered. The projector’s name and IP address are included in the
body of the message.
12. When done making all your projector settings, close EMP
NetworkManager. (It does not have to be open for messages to be
sent or received.)
92
Managing Projectors
User's Guide.book Page 93 Tuesday, May 25, 2004 11:49 AM
Understanding the Notification Messages
If a projector experiences a problem, it sends an e-mail message to
each of the addresses you provided using EMP NetworkManager. The
message includes the heading “EPSON Projector” in the subject line.
The body of the message contains:
■
the name of the projector
■
the projector’s IP address
■
a description of the problem
The problem descriptions are similar to the errors reported by EMP
Monitor listed on page 87.
If a plus (+) sign appears before the description, it indicates that a
problem has occurred. A minus (–) sign appears when the problem
goes away or is resolved.
note
If a projector develops a
critical problem, it may not
be possible for it to report the
error.
Managing Projectors 93
User's Guide.book Page 94 Tuesday, May 25, 2004 11:49 AM
94
Managing Projectors
User's Guide.book Page 95 Tuesday, May 25, 2004 11:49 AM
1
Maintaining the Projector
warning
Before you clean any part of
the projector, turn it off and
unplug the power cord.
Never open any cover on the
projector, except the lamp
cover. Dangerous electrical
voltages in the projector can
injure you severely. Do not
try to service this product
yourself, except as specifically
explained in this User’s
Guide. Refer all other
servicing to qualified service
personnel.
Y
our projector needs little maintenance. All you have to do is keep
the lens clean and periodically clean the air filters at the side and base
of the projector. A clogged air filter can block ventilation needed to
cool the projector.
The only parts you should replace are the lamp and air filters. If any
other part needs replacing, contact your dealer or a qualified servicer.
This chapter covers the following:
■
Cleaning the lens
■
Cleaning the projector case
■
Cleaning the air filters and vents
■
Replacing the lamp and air filters
■
Transporting the projector
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on the surface.
Use a canister of compressed air to remove dust.
To remove dirt or smears on the lens, use lens-cleaning tissue. If
necessary, moisten a soft cloth with lens cleaner and gently wipe the
lens.
Remove the cap
before cleaning
95
User's Guide.book Page 96 Tuesday, May 25, 2004 11:49 AM
Cleaning the Projector Case
caution
Do not use wax, alcohol,
benzene, thinner, or other
chemical detergents. These
can damage the case.
Before you clean the case, turn off the projector and unplug the power
cord.
■
To remove dirt or dust, wipe the case with a soft, dry, lint-free
cloth.
■
To remove stubborn dirt or stains, moisten a soft cloth with water
and a neutral detergent. Then wipe the case.
Cleaning the Air Filters and Vents
note
To order replacement air
filters, request part number
V13H134A07. See page 13
for ordering information.
Clean the air filters and air intake vents after every 100 hours of use. If
they are not cleaned periodically, they can become clogged with dust,
preventing proper ventilation. This can cause overheating and damage
the projector.
Follow these steps:
1. Turn off the projector. Wait for the Power light to stop flashing,
then unplug the power cord.
2. To clean the intake vents, use a small vacuum cleaner designed for
computers and other office equipment. If you don’t have one,
gently clean the vents with a soft brush (such as an artist’s
paintbrush).
96
Maintaining the Projector
User's Guide.book Page 97 Tuesday, May 25, 2004 11:49 AM
3. If the dirt is difficult to remove or a filter is broken, replace the
filters as described on the next page. Contact your dealer or call
Epson at (800) 873-7766 in the United States to obtain new ones.
In Canada, please call (800) 463-7766 for dealer referral.
Replacing the Lamp and Air Filters
note
The life span of the projection lamp is about 2000 hours if
Brightness Control in the Setting menu is set to High (default), and
3000 hours if Brightness Control is set to Low.
When you get a replacement
lamp for your projector, you
should replace the filters.
It is time to replace the lamp when:
To check how long the lamp
has been in use, see
page 105.
■
The projected image gets darker or starts to deteriorate.
■
The message Replace the lamp appears on the screen when the
lamp comes on and the lamp warning light
flashes orange. To
maintain projector brightness and image quality, replace the lamp
as soon as possible.
■
The lamp warning light
flashes red (the lamp is burnt out).
Contact your dealer or call Epson at (800) 873-7766 in the United
States for a replacement lamp. Request part number V13H010L31. In
Canada, please call (800) 463-7766 for dealer referral.
Follow these steps to replace the lamp and air filters:
1. Turn off the projector.
warning
2. When the Power light stops flashing, unplug the power cord.
3. Let the projector cool for at least an hour (if it has been on). The
lamp is extremely hot immediately after use.
Let the lamp cool fully
before replacing it.
In the unlikely event that
the lamp has broken, small
glass fragments may be
present and should be
removed carefully to avoid
injury.
Maintaining the Projector 97
User's Guide.book Page 98 Tuesday, May 25, 2004 11:49 AM
4. Turn the projector over and remove the air filters at the side and
bottom of the projector.
5. Insert the two new air filters. They should click into place.
6. Turn the projector back over.
7. Loosen the screw holding the lamp cover in place (you don’t need
to remove it). Then remove the lamp cover.
8. Loosen the two screws holding the lamp in place (you don’t need
to remove them).
Loosen, but don’t
remove these
98
Maintaining the Projector
User's Guide.book Page 99 Tuesday, May 25, 2004 11:49 AM
9. Grasp the handles as shown and pull the lamp straight out.
10. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is
facing the right way.)
11. Once the lamp is fully inserted, tighten its screws and replace the
cover, then tighten the cover screw. (The projector won’t come on
if the lamp cover is loose.)
12. Reset the lamp timer as described in the next section.
Resetting the Lamp Timer
After you replace the lamp, you need to reset the lamp timer using the
projector’s menus.
1. Press the Menu button on the remote control or on the
projector’s control panel. You see the main menu.
2. Use the
pointer button on the remote control (or the arrow
buttons on the projector) to highlight Reset, then press Enter.
You see this screen:
Maintaining the Projector 99
User's Guide.book Page 100 Tuesday, May 25, 2004 11:49 AM
3. Select Lamp Hours Reset and press Enter. You see this prompt:
4. Select Yes and press Enter.
5. When you’re finished, press Esc or Menu to exit.
Transporting the Projector
The projector contains many glass and precision parts. Follow these
guidelines to prevent damage:
note
■
When shipping the projector for repairs, use the original
packaging material if possible. If you do not have the original
packaging, use equivalent materials, placing plenty of cushioning
around the projector.
■
When transporting the projector a long distance, first place it in a
hard-shell shipping case, then pack it in a firm box with
cushioning around the case. (An optional case is available from
Epson; see page 13.)
Epson shall not be liable for
any damages incurred
during transportation.
100
Maintaining the Projector
User's Guide.book Page 101 Tuesday, May 25, 2004 11:49 AM
1
Solving Problems
This chapter helps you solve problems with your projector, and tells
you how to contact technical support for problems you can’t solve
yourself. The following information is included:
■
Using the projector’s on-screen help system
■
What to do when the projector’s status lights flash
■
Solving problems with the image or sound
■
Solving problems with EasyManagement
■
Solving problems with the remote control
■
Contacting technical support
101
User's Guide.book Page 102 Tuesday, May 25, 2004 11:49 AM
Using On-Screen Help
If the image doesn’t look right or your audio isn’t working, you can
get help by pressing the blue ? Help button on top of the projector or
on the remote control. The following choices are available:
■
Problems with image
■
Problems with sound
■
Language change
Follow these steps to get help:
1. Press the blue ? Help button on the projector.
? Help button
on projector
You see the Help Menu:
2. Use the
pointer button on the remote control or the arrow
buttons on the projector to highlight menu items.
3. Press the Enter button on the remote control or on the projector
to select the menu item.
4. To exit the help system, press the ? Help button.
If none of the suggestions solve your problem, see additional solutions
to problems in the following sections.
102
Solving Problems
User's Guide.book Page 103 Tuesday, May 25, 2004 11:49 AM
Checking Projector Status
If your projector isn’t working correctly, first turn it off, wait for it to
cool (the Power light stops flashing orange), and unplug it. Then
plug the power cord back in and turn on the projector. If this doesn’t
solve the problem, check the lights on top of the projector.
What To Do When the Lights Flash
The lights on top of the projector indicate the projector’s status.
Power light
Lamp light
Temperature light
Refer to the following table for a complete description of the
projector’s status lights:
Status lights
Light
Status
Description
Orange
The projector is in sleep mode. You can unplug it or press the P Power
button to turn it on.
Flashing green
The projector is warming up. Wait for the image to appear.
Green
The projector is operating normally.
Flashing orange
The projector is cooling down. You can’t turn it back on (and you should
not unplug it) until the light stops flashing and remains orange.
Flashing red
There is a problem with the fan or temperature sensor. Stop using the
projector, disconnect the power cable, and contact Epson.
Solving Problems 103
User's Guide.book Page 104 Tuesday, May 25, 2004 11:49 AM
Status lights
Light
Status
Description
Flashing orange
Rapid cooling is in progress. Although this is not an abnormal condition,
projection will stop automatically if the temperature rises higher. Make
sure there is plenty of space around and under the projector for
ventilation, and that the air filters and vents are clear.
Red
The projector is overheating, which turns the lamp off automatically.
Wait until the cooling fan stops, then unplug the power cord. Plug the
power cord back in and press the P Power button. Make sure the room
temperature is not above 95 °F (35 °C), and there is plenty of space
around and under the projector for ventilation.
The air filters may be clogged. Clean or replace them as described on
page 96.
If the projector continues to overheat after you clean the air filter, the
problem may be caused by damage to the cooling fan or temperature
sensor. Contact Epson for help.
Warning: Except as specifically explained in this User’s Guide, do not
attempt to service this product yourself.
104
Flashing orange
It’s time to replace the lamp. See page 97 for instructions. If you continue
to use the lamp after the replacement warning, there is an increased
possibility that the lamp may break.
Flashing red
The lamp may be burnt out. First make sure the lamp cover is securely
installed. If that’s not the problem, let the lamp cool, remove the lamp,
and replace it as described on page 97. If this does not resolve the
problem, contact Epson as described on page 112.
Flashing red
Power is cut off because of an internal problem. Unplug the power cord
and contact Epson for help, as described on page 112.
Solving Problems
User's Guide.book Page 105 Tuesday, May 25, 2004 11:49 AM
Viewing Lamp Usage and Other Information
Use the Info menu to view information about the display settings of
your computer and the number of hours the lamp has been used.
Press the Menu button and highlight the Info menu.
You see the lamp usage hours and various input signal settings on the
right.
The life span of the lamp is about 2000 hours if the Brightness
Control setting in the Setting menu is set to High (default), and 3000
hours if the Brightness Control setting is set to Low. Make sure you
have a spare lamp handy if the usage hours on this menu are close to
the life span of your lamp.
note
The information displayed
depends on the input signal
currently selected.
Solving Problems with the Image
or Sound
No image appears on the screen.
■
Check that the Power light is green, not flashing, and the lens
cap is off.
■
The projector may be in sleep mode. If the Power light is orange,
press the P Power button to turn the projector on.
■
If the power was switched off and then on again, the projector
may be cooling down. Wait until the Power light stops flashing
and remains orange; then press the P Power button again.
■
Press the A/V Mute button to make sure the picture has not been
turned off temporarily.
■
The attached computer may be in sleep mode or displaying a
black screen saver. Try pressing a key on the computer.
You’ve connected a computer and see a blue screen with the
message No Signal displayed.
■
Make sure the cables are connected correctly, as described on
page 46.
Solving Problems 105
User's Guide.book Page 106 Tuesday, May 25, 2004 11:49 AM
■
Try restarting your computer.
■
If you’ve connected a computer and one or more video sources,
you may need to press one of the Source buttons on the projector
or remote control to select the correct source. Allow a few seconds
for the projector to sync up after pressing the button.
If you’re using a PC notebook:
■
Hold down the Fn key on the keyboard and press the function
key that lets you display on an external monitor. It may have an
icon such as
, or it may be labelled CRT/LCD. Allow a few
seconds for the projector to sync up after pressing it. Check your
notebook’s manual or online help for details.
On most systems, the
key lets you toggle between the LCD
screen and the projector, or display on both at the same time.
■
Depending on your computer’s video card, you might need to use
the Display utility in the Control Panel to make sure that both the
LCD screen and external monitor port are enabled. See your
computer’s documentation or online help for details.
If you’re using Macintosh OS X:
1. Open System Preferences.
2. Click Displays.
3. Make sure the VGA Display or Color LCD dialog box is selected.
4. Click the Arrangement or Arrange tab.
5. Make sure the Mirror Displays checkbox is selected.
If you’re using Macintosh OS 8.6 to 9.x:
1. From the Apple menu, select Control Panels, then click
Monitors and Sound.
2. Click the Arrange icon.
3. Drag one monitor icon on top of the other. This lets you display
on the projector screen as well as the LCD screen.
4. If this option isn’t available, click the Monitor icon.
106
Solving Problems
User's Guide.book Page 107 Tuesday, May 25, 2004 11:49 AM
5. Select one of the listed Simulscan resolutions. (Allow a few
seconds for the projector to sync up after making the selection.)
The message Not Supported is displayed.
■
Make sure the correct input signal is selected in the Signal menu
(see page 63).
■
Make sure your computer’s resolution doesn’t exceed UXGA
(1600 × 1200) and the frequency is supported by the projector
(see page 119). If necessary, change your computer’s resolution
setting as described below.
Only part of the computer image is displayed.
■
Press the Auto button on the remote control.
■
Make sure the image Position setting is correct on the Signal
menu. See Chapter 6 for more information.
■
Make sure your computer’s resolution setting is correct. Ideally, it
should be 1024 × 768 to match the projector’s native resolution.
If this option isn’t available, select one of the other compatible
video formats listed on page 119.
■
■
Windows:
Right-click the desktop, select Properties, click the Settings
tab, and select a different resolution.
■
Macintosh OS X:
Open System Preferences, click Displays, and select a
different resolution.
■
Macintosh OS 8.6 to 9.x:
On the Apple menu, choose Control Panels, and click
Monitors and Sound. Select a different resolution.
You also may need to modify existing presentation files if you
created them for a different resolution. See your software
documentation for specific information.
Solving Problems 107
User's Guide.book Page 108 Tuesday, May 25, 2004 11:49 AM
The image isn’t square, but keystone-shaped.
■
If the top or bottom of the image is broader, press the Sync + or
Sync - button on the projector until the image is square.
■
If the projector is angled toward the screen from the left or right,
the image will be broader on one side. Center the projector in
front of the middle of the screen, facing the screen squarely. If this
doesn’t work, press the Tracking + or Tracking - button on the
projection until the image is square.
■
If the image has no parallel sides, use Quick Corner. Press the
Menu button, select the Setting menu, and select Keystone.
Select Quick Corner and make your adjustments with the
pointer button. See page 36 for details.
The image contains static or noise.
■
Make sure the correct input signal is selected in the Signal menu
(see Chapter 6).
■
If you’re using a computer cable longer than 6 feet, or an
extension cable, the image quality may be reduced.
■
Keep your computer and video cables away from the power cord
as much as possible to prevent interference.
■
The video signal may be split between the computer and the
projector. If you notice a decline in the projected image quality
when the image is displayed simultaneously on your notebook
computer and the projector, turn off the notebook’s LCD display.
The image is blurry.
108
Solving Problems
■
There may be dirt or smears on the lens. Clean the lens as
described on page 95.
■
Adjust the focus using the focus buttons (see page 25).
■
Make sure the lens is not fogged by condensation. You may need
to wait before using the projector after moving it from a cold
environment to a warm environment.
User's Guide.book Page 109 Tuesday, May 25, 2004 11:49 AM
■
Adjust the Sharpness setting on the Image menu (see page 62).
When you change video settings, you should be able to see the
effect on the screen immediately. If you’re projecting from a
computer, you may also need to adjust the tracking and sync as
described in the next section. If you don’t like the new settings,
you can always select Reset to return to the factory default
settings.
You see vertical bands or the image still looks blurry after
trying the solutions in the previous section.
■
If you’re projecting from a computer and displaying an image that
contains a lot of fine detail, you may notice vertical bands or some
of the characters may look heavy or blurred. Press the Auto
button on the remote control to reset the projector’s tracking and
sync settings.
■
If further adjustment is needed, you can fine-tune the Tracking
and Sync settings manually using the buttons on the projector.
1. Fill the screen with an image containing fine detail, such as
pattern to appear as your desktop background, or try
projecting black text on a white background.
2. Adjust the Tracking to eliminate vertical bands.
3. Adjust the Sync setting to increase the image sharpness.
Solving Problems 109
User's Guide.book Page 110 Tuesday, May 25, 2004 11:49 AM
The image colors are incorrect.
note
Because of the different
technologies used, your
projected image may not
exactly match the colors on
your notebook or computer
monitor.
■
If you’re displaying a computer image, use the Color Mode
option in the projector’s Image menu to adjust the color. If you’re
displaying video, adjust the Color Adjustment and Color Mode
settings on the Image menu.
■
Check your computer display settings to correct the color balance.
There is no sound.
110
Solving Problems
■
Make sure A/V Mute is not enabled. (The A/V Mute button may
have been pressed.)
■
Try adjusting the Volume setting in the Setting menu (see
page 67).
■
If you’re using a VCR or other video source, make sure the
volume is not turned all the way down or muted. Also, make sure
the cables are connected correctly, as described in on page 56.
■
If your presentation includes computer audio, make sure the
volume control on your computer is not turned all the way down
or muted. If you’re using the audio cable, make sure it is securely
connected to both the projector and your computer’s
headphone jack or
audio out jack.
■
Make sure the Windows volume controls on your computer are
not turned all the way down or set to Mute. You may be able to
check this by clicking the volume control in your Windows
system tray (lower right corner of the screen).
User's Guide.book Page 111 Tuesday, May 25, 2004 11:49 AM
Solving EasyManagement Problems
You don’t see your projector in the EMP Monitor window.
■
Make sure that you’ve connected the projector to the network and
configured it correctly; see page 80. Also, make sure you’ve
registered the projector with EMP Monitor; see page 81.
■
Make sure that Standby Mode in the projector’s Extended menu
is set to Network ON.
■
If the computer you are using is running Windows XP or 2000,
you must be logged in as the Administrator.
■
Try restarting your computer.
Solving Problems with the Remote
Control
The projector doesn’t respond to remote control commands.
■
Be sure the ON/OFF switch is in the ON position, as shown on
page 19.
■
The remote control’s batteries may not be installed correctly or
may be low on power. To change the batteries, see page 33.
■
Make sure your remote control’s ID is set to 0 or to the
projector’s ID; see page 73.
■
Make sure you are within about 33 feet (10 meters) of the
projector and within range of the projector’s front or back sensor
(approximately 20° to the left or right and 40° above or below).
■
Dim the room lights and turn off any fluorescent lights. Make
sure the projector is not in direct sunlight. Strong lighting,
especially fluorescent lights, may affect the projector’s infrared
receivers. Also, turn off any nearby equipment that emits infrared
energy, such as a radiant room heater.
Solving Problems 111
User's Guide.book Page 112 Tuesday, May 25, 2004 11:49 AM
Where To Get Help
Epson provides technical assistance through electronic support
services 24 hours a day, as listed in the following table.
Service
Access
World Wide Web
From the Internet, you can reach Epson’s product support page at
http://support.epson.com. After selecting your product, you can access
troubleshooting information, download product documentation, and receive
technical advice through e-mail.
Presenters Online
Access tips, templates, and training for developing successful presentations at
http://www.presentersonline.com
Telephone Support Services
To use the Epson PrivateLine Support service, call (800) 637-7661
and enter the PIN on the Epson PrivateLine Support card included in
your Start Here kit. This is the fastest way of speaking to a live
representative, and it’s free. This service is available 6 AM to 6 PM,
Pacific Time, Monday through Friday, for the duration of your
warranty period.
You may also speak with a projector support specialist by dialing one
of these numbers:
■
U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday
through Friday
■
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday
through Friday
Toll or long distance charges may apply.
Before you call, please have the following information ready:
■
Product name (Epson PowerLite 830p)
■
Product serial number (located on the bottom of the projector)
■
Computer configuration
■
Description of the problem
You can purchase screens, carrying cases, or other accessories from
Epson at (800) 873-7766 or by visiting the Epson Store at
www.epsonstore.com (U.S. sales only). In Canada, please call
(800) 463-7766 for dealer referral.
112
Solving Problems
User's Guide.book Page 113 Tuesday, May 25, 2004 11:49 AM
A
Software Installation
T
he Epson Projector Software CD-ROM includes EMP Monitor
and EMP Network Manager for presenting and monitoring the
projector from a remote location.
Windows System Requirements
Before you install the software, make sure your computer meets these
requirements:
■
Microsoft Windows 98, 2000, Me, or XP
■
IBM® compatible PC with at least a Pentium® III 700 MHz
processor
■
At least 256MB of RAM
■
At least 128MB of free hard disk space
■
SVGA (800 × 600) or better display adapter and monitor
113
User's Guide.book Page 114 Tuesday, May 25, 2004 11:49 AM
Installing the Software on a Windows
System
Follow these steps:
1. Insert the Epson Projector software CD-ROM in your computer’s
CD-ROM or DVD drive. You see this screen:
2. Click Install, then follow the on-screen instructions to install
your projector software.
When you see a message that the Epson GDI Monitor Driver has
not passed Windows Logo testing, click Continue Anyway.
3. When installation is complete, close the installation window.
114
Software Installation
User's Guide.book Page 115 Tuesday, May 25, 2004 11:49 AM
A
Projector Installation
T
his appendix provides guidelines on installing the projector in a
permanent location, such as a theater or conference room.
The projector can be installed for four different viewing setups: front
projection, ceiling mounting, rear projection onto a semi-transparent
screen, or rear/ceiling projection, as shown:
Front projection
Ceiling mounting
Rear projection
Rear/ceiling projection
To project from overhead, you’ll need the optional ceiling mounting
hardware; see page 13 for ordering information. You’ll also need to
select Front/Ceiling or Rear/Ceiling as the Projection option of the
projector’s Extended menu to flip the image upside-down. To project
from the rear, onto a semi-transparent screen, select Rear or
Rear/Ceiling (see page 75).
If you’re mounting the projector on the ceiling and you place it above
screen level, you’ll have to tilt the projector down to position the
image on the screen. This causes the image to lose its square shape.
115
User's Guide.book Page 116 Tuesday, May 25, 2004 11:49 AM
You can correct the distortion using the Keystone function in the
projector’s menu system (see page 65) or the keystone buttons on the
projector’s control panel.
If you place the projector so that the base of the lens is level with the
bottom of the screen, the image should be square and you won’t have
to adjust it. If you place the lens lower than the bottom of the screen,
you’ll have to tilt the projector upward if you want to fill the whole
screen with the image.
116
Projector Installation
User's Guide.book Page 117 Tuesday, May 25, 2004 11:49 AM
A
Technical Specifications
General
Type of display
Poly-silicon TFT active matrix
Size of LCD panels
Diagonal: 0.8 inches (20.3 mm)
Resolution
(native format)
1024 × 768 pixels (XGA)
Color reproduction
24 bit, 16.8 million colors
Brightness
3000 lumens (High Brightness mode)
2200 lumens (Low Brightness mode)
Contrast ratio
600:1
Image size
30 to 300 inches
Projection distance
2.8 to 48.3 feet (0.9 to 14.7 meters)
Projection methods
Front, rear, upside-down (ceiling mount)
Internal sound system
5 W monaural
Optical aspect ratio
4:3 (horizontal:vertical)
Zoom ratio
1:1.6
Noise level
28 dB or 34 dB
(depends on the Brightness Control setting
in the Setting menu)
Keystone correction
Automatic (vertical and horizontal); manual
adjustment capability ±45° (vertical) and
±25° (horizontal)
Mouse compatibility
Supports USB
117
User's Guide.book Page 118 Tuesday, May 25, 2004 11:49 AM
Projection Lamp
Type
UHE (Ultra High Efficiency)
Power consumption
200 W
Lamp life
Approx. 2000 hours (High Brightness
mode)
Approx. 3000 hours (Low Brightness mode)
Part number
V13H010L31
Remote Control
Range
33 feet (10 meters)
Batteries (2)
Alkaline AA
Dimensions
Height
4.5 inches (114 mm), feet retracted
Width
14.4 inches (365 mm)
Depth
11.0 inches (280 mm)
Weight
10.4 lb (4.7 kg)
Electrical
Rated frequency
50/60 Hz AC
Power supply
100 to 120 VAC, 3.6 A
200 to 240 VAC, 1.6 A
Power consumption
Operating: 310 W
Environmental
Temperature
Humidity
(non-condensing)
Operating: 41 to 95 °F (5 to 35 °C)
Storage: 14 to 140 °F (-10 to 60 °C)
Operating: 20 to 80% RH
Storage: 10 to 90% RH
118
Technical Specifications
User's Guide.book Page 119 Tuesday, May 25, 2004 11:49 AM
Safety
United States
FCC 47CFR Part 15B Class B (DoC)
UL60950 Third Edition
Canada
ICES-003 Class B
CSA C22.2 No. 60950 (cUL)
CE Marking
Directive 73/23/EEC
Directive 89/336/EEC
IEC 60950 Third Edition
EN 55022, EN 55024
Pixelworks™ DNX™ ICs are used in this projector.
Compatible Video Formats
The projector supports NTSC, PAL, and SECAM international video
standards, as well as the monitor display formats listed below.
To project images output from a computer, the computer’s video card
must be set at a refresh rate (vertical frequency) that’s compatible with
the projector. Some images are automatically resized to display in the
projector’s “native” format (XGA). The frequencies of some
computers may not allow images to display correctly; see your
computer’s documentation for details.
Mode
Refresh Rate (Hz)
Resolution
VGA EGA
70
640 × 350*
VGA—60
VESA—72
VESA—75
VESA—85
60
72
75
85
640 × 480*
640 × 480*
640 × 480*
640 × 480*
SVGA—56
SVGA—60
SVGA—72
SVGA—75
SVGA—85
SVGA—120
56
60
72
75
85
120
800 × 600*
800 × 600*
800 × 600*
800 × 600*
800 × 600*
800 × 600*
Technical Specifications 119
User's Guide.book Page 120 Tuesday, May 25, 2004 11:49 AM
Mode
Refresh Rate (Hz)
Resolution
XGA—60
XGA—70
XGA—75
XGA—85
XGA—100
XGA—120
60
70
75
85
100
120
1024 × 768
1024 × 768
1024 × 768
1024 × 768
1024 × 768
1024 × 768
SXGA1—70
SXGA1—75
SXGA1—85
SXGA1—100
70
75
85
100
1152 × 864*
1152 × 864*
1152 × 864*
1152 × 864*
SXGA2—60
SXGA2—75
SXGA2—85
60
75
85
1280 × 960*
1280 × 960*
1280 × 960*
SXGA3—60
SXGA3—75
SXGA3—85
60
75
85
1280 × 1024*
1280 × 1024*
1280 × 1024*
UXGA—60
UXGA—65
UXGA—70
UXGA—75
UXGA—80
UXGA—85
60
65
70
75
80
85
1600 × 1200*
1600 × 1200*
1600 × 1200*
1600 × 1200*
1600 × 1200*
1600 × 1200*
MAC13
MAC16
MAC19
MAC21
67
75
75
75
640 × 480*
832 × 624*
1024 × 768
1152 × 870*
NTSC
NTSC 4:43
PAL
N-PAL
M-PAL
PAL—60
SECAM
60
60
50
50
60
60
50
—
—
—
—
—
—
—
HDTV (720p)
HDTV (1080i)
60
60
1024 × 576*
1024 × 576*
SDTV (480i)
SDTV (480p)
SDTV (625i)
SDTV (625p)
60
60
50
50
1024 × 768
1024 × 768
1024 × 768
1024 × 768
*The
120
Technical Specifications
image is resized using Epson’s SizeWise™ Technology.
User's Guide.book Page 121 Tuesday, May 25, 2004 11:49 AM
A
Notices
This appendix includes safety instructions and other important information
about your Epson PowerLite projector.
Important Safety Instructions
Follow these safety instructions when setting up and using the projector:
■
Do not place the projector on an unstable cart, stand, or table.
■
Do not use the projector near water or sources of heat.
■
Use the type of power source indicated on the projector. If you are not
sure of the power available, consult your dealer or power company.
■
Place the projector near a wall outlet where the plug can be easily
unplugged.
Placez l’appareil près d’une prise de courant où la fiche peut être débranchée
facilement.
■
Insert the projector’s three-wire grounding-type plug into a properly
grounded outlet. If you have a two-prong outlet, contact an electrician
to replace it. Do not hold the plug with wet hands.
■
Take the following precautions for the plug. Failure to comply with
these precautions could result in sparks or fire: Do not insert the plug
into an outlet with dust present. Insert the plug firmly into the outlet.
■
Do not overload wall outlets, extension cords, or integral convenience
receptacles. This can cause fire or electric shock.
■
Do not place the projector where the cord can be walked on. This may
result in fraying or damage to the plug.
■
Unplug the projector from the wall outlet before cleaning. Use a damp
cloth for cleaning. Do not use liquid or aerosol cleaners.
■
Do not block the slots and openings in the projector case. They provide
ventilation and prevent the projector from overheating. Do not operate
the projector on a sofa, rug, or other soft surface, or in a closed-in
cabinet unless proper ventilation is provided.
121
User's Guide.book Page 122 Tuesday, May 25, 2004 11:49 AM
■
Never push objects of any kind through the cabinet slots. Never spill
liquid of any kind into the projector.
■
Except as specifically explained in this User’s Guide, do not attempt to
service this product yourself. Refer all servicing to qualified personnel.
Opening or removing covers may expose you to dangerous voltages and
other hazards.
■
Unplug the projector from the wall outlet and refer servicing to qualified
service personnel under the following conditions: When the power cord
or plug is damaged or frayed. If liquid has been spilled into the
projector, or if it has been exposed to rain or water. If it does not operate
normally when you follow the operating instructions, or if it exhibits a
distinct change in performance, indicating a need for service. If it has
been dropped or the housing has been damaged.
■
This product includes a lamp component that contains mercury (Hg).
Please consult your state and local regulations regarding proper disposal
and do not put in the trash.
■
Unplug the projector during lightning storms or when it will not be used
for extended periods.
■
Do not place the projector and/or remote control on top of
heat-producing equipment or in a hot location.
■
If you use the projector in a country other than where you purchased it,
use the correct power cord for that country.
■
Do not stand on the projector or place heavy objects on it.
■
Do not use the projector outside of the required temperature range of 41
to 95 °F (5 to 35 °C). Doing so may cause an unstable display and could
lead to projector damage.
■
Do not store the projector outside of the required temperature range of
14 to 140 °F (-10 to 60 °C) or in direct sunlight for long periods of time.
Doing so may cause damage to the case.
WARNING: This product contains chemicals, including lead, known to the
State of California to cause birth defects or other reproductive harm.
Wash hands after handling.
122
Notices
User's Guide.book Page 123 Tuesday, May 25, 2004 11:49 AM
Remote Control Information
You can operate the projector by remote control via a line-of-sight infrared
(IR) receiver at the front and rear of the projector. The projector may not
respond to remote control commands under the following conditions:
■
There is an object between the remote control IR emitter and the IR
receiver on the projector.
■
Ambient light is too bright.
■
Certain types of fluorescent lighting are used.
■
A strong light source shines into the IR receiver.
■
Other equipment that emits infrared energy, such as a radiant room
heater, is in the room.
These conditions commonly cause problems for most infrared-controlled
equipment. Try the following:
■
The remote control’s batteries may be low on power; replace them.
■
Dim the ambient lighting and/or turn off any fluorescent lights.
■
Close any window coverings and/or move the projector out of direct
sunlight.
■
Turn off other equipment that emits infrared energy.
Notices 123
User's Guide.book Page 124 Tuesday, May 25, 2004 11:49 AM
Declaration of Conformity
According to 47CFR, Part 2 and 15, Class B Personal Computers and
Peripherals; and/or CPU Boards and Power Supplies used with Class B
Personal Computers
We:
Located at:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806-2469
Telephone:
(562) 290-5254
Declare under sole responsibility that the product identified herein, complies
with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each
product marketed, is identical to the representative unit tested and found to
be compliant with the standards. Records maintained continue to reflect the
equipment being produced can be expected to be within the variation
accepted, due to quantity production and testing on a statistical basis as
required by 47CFR §2.909. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Trade Name:
Epson
Type of Product: Projector
Model:
EMP-830
Marketing Name: PowerLite 830p
124
Notices
User's Guide.book Page 125 Tuesday, May 25, 2004 11:49 AM
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio and television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
■
Reorient or relocate the receiving antenna.
■
Increase the separation between the equipment and receiver.
■
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
■
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification of this device and may cause
interference levels which exceed the limits established by the FCC for this
equipment. It is the responsibility of the user to obtain and use a shielded
equipment interface cable with this device. If this equipment has more than
one interface connector, do not leave cables connected to unused interfaces.
Changes or modifications not expressly approved by the manufacturer could
void the user’s authority to operate the equipment.
For Canadian Users
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur le materiel brouilleur du Canada.
Notices 125
User's Guide.book Page 126 Tuesday, May 25, 2004 11:49 AM
Warranty
Epson America, Inc. Limited Warranty
Basic Two-Year Warranty and 90-Day Lamp Warranty
What Is Covered: Epson America, Inc. (“Epson”) warrants to the original
retail purchaser of the Epson product enclosed with this limited warranty
statement that the product, if purchased new and operated in the United
States or Canada, conforms to the manufacturer’s specifications and will be
free from defects in workmanship and materials for a period of two (2) years
from the date of original purchase (except that the warranty period is 90 days
for projector lamps). For warranty service, you must provide proof of the date
of original purchase.
What Epson Will Do To Correct Problems: If you elect carry-in warranty
service, please bring the product securely packaged in its original container or
an equivalent, along with proof of the date of original purchase, to your
Epson Dealer or Epson Customer Care Center. Epson will, at its option,
repair or replace on an exchange basis the defective unit, without charge for
parts or labor. When warranty service involves the exchange of the product or
of a part, the item replaced becomes Epson property. The exchanged product
or part may be new or previously refurbished to the Epson standard of
quality, and at Epson’s option, the replacement may be another model of like
kind and quality. Epson’s liability for replacement of the covered product will
not exceed the original retail selling price of the covered product. Exchange
or replacement products or parts assume the remaining warranty period of
the product covered by this limited warranty. However, each replacement
lamp carries the limited 90-day warranty stated above.
What This Warranty Does Not Cover: This warranty does not apply to
refurbished or reconditioned products. This warranty covers only normal
consumer use in the United States and Canada. 24-hour-per-day use causes
unusual strain and is not considered normal use. This warranty does not
cover consumables (e.g., fuses), other than lamps. This warranty is not
transferable. Epson is not responsible for warranty service should the Epson
label or logo or the rating label or serial number be removed or should the
product fail to be properly maintained or fail to function properly as a result
of misuse, abuse, improper installation, neglect, improper shipping, damage
caused by disasters such as fire, flood, and lightning, improper electrical
current, software problems, interaction with non-Epson products, or service
other than by an Epson Authorized Servicer. Postage, insurance, or shipping
costs incurred in presenting your Epson product for carry-in warranty service
are your responsibility. If a claimed defect cannot be identified or reproduced
in service, you will be held responsible for costs incurred.
126
Notices
User's Guide.book Page 127 Tuesday, May 25, 2004 11:49 AM
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE
EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED
WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW
THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS
APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE
LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE.
UNLESS STATED HEREIN, ANY STATEMENTS OR
REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM
ARE VOID. IN THE EVENT THE REMEDIES ABOVE FAIL, EPSON’S
ENTIRE LIABILITY SHALL BE LIMITED TO A REFUND OF THE
PRICE PAID FOR THE EPSON PRODUCT COVERED BY THIS
LIMITED WARRANTY. EXCEPT AS PROVIDED IN THIS WRITTEN
WARRANTY, NEITHER EPSON AMERICA, INC. NOR ITS
AFFILIATES SHALL BE LIABLE FOR ANY LOSS, INCONVENIENCE,
OR DAMAGE, INCLUDING DIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, RESULTING FROM THE USE OR
INABILITY TO USE THE EPSON PRODUCT, WHETHER
RESULTING FROM BREACH OF WARRANTY OR ANY OTHER
LEGAL THEORY.
In Canada, warranties include both warranties and conditions.
Some jurisdictions do not allow limitations on how long an implied warranty
lasts and some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations and exclusions
may not apply to you. This warranty gives you specific legal rights, and you
may also have other rights, which vary from jurisdiction to jurisdiction.
To locate the Authorized Epson Servicer nearest you, call the Epson
ConnectionSM at (800) 637-7661 + PIN or (562) 276-4394 in the U.S. and
(905) 709-3839 in Canada or write to: Epson America, Inc., P.O. Box
93012, Long Beach, CA 90809-3012.
Notices 127
User's Guide.book Page 128 Tuesday, May 25, 2004 11:49 AM
128
Notices
User's Guide.book Page 129 Tuesday, May 25, 2004 11:49 AM
Index
A
A/V Mute, 37, 72, 105
About menu, 99 to 100, 105
Accessories, 13, 112
Adapter, Macintosh, 13, 48
Air filter
cleaning, 96 to 97
ordering, 13
replacing, 97 to 98
Anti-theft device, 13, 17
Aspect ratio, 117
Audio
adjusting volume, 67
connecting equipment, 56 to 57
problems, troubleshooting, 110
turning off (using A/V Mute), 37
Auto button, 28
Auto Setup setting, 64
B
Background Color setting, 69
Bands, vertical, 109
Batteries, installing, 33
Blackboard, projecting on, 40 to 41
Blank screen, 21 to 23
Blurry image, 108 to 109
Brightness, 117
Brightness setting, 63
C
Cables
included with projector, 12
mouse, 49
ordering, 13
remote control cable set, 13
S-video, 13, 53
VGA-to-component, 47
Capturing image, 71 to 72
Carrying case, 13, 100
Ceiling mount, 13, 115 to 116
Cleaning
air filter, 96 to 97
lens, 95
projector case, 96
Color
correcting with Wall Shot, 40 to 41
problems, 110
settings, 66
Color Mode setting, 62, 66
Component video cable, 13, 51
Composite (RCA) video cable, 51 to 52
Computer
connecting to, 46 to 48
correcting images, 28
selecting source, 20
Connecting projector
to a computer, 46 to 48
to an external monitor, 50
to audio equipment, 56 to 57
to video equipment, 51 to 55
Contrast setting, 63
D
Declaration of Conformity, 124
Default settings, restoring, 61
Desktop adapter, Macintosh, 13, 48
Direct Power On, 30
Distance from projector to screen, 16, 117
Documentation, 10
DVD player, connecting, 51 to 55
E
EasyManagement
configuring the projector, 80 to 81
installing software, 113 to 114
monitoring the projector, 81 to 88
problems, 111
receiving e-mail alerts, 89 to 92
Electrical specifications, 118
Index 129
User's Guide.book Page 130 Tuesday, May 25, 2004 11:49 AM
EMP Monitor
installing software, 114
problems, 111
using, 81 to 88
EMP NetworkManager, using, 89 to 93
Environmental specifications, 118
Epson
accessories, 13, 112
presentation tips, 10
PrivateLine Support, 11, 112
technical support, 10, 112
E-Zoom button, 38
F
FCC compliance statement, 125
Filter, see Air filter
Focusing image, 25
Freeze button, 37
Image
adjusting, 24 to 28, 62 to 66
blurry, 108 to 109
capturing and saving in projector, 71 to 72
correcting shape, 26 to 27, 36, 65, 108
fitting on screen, 64, 107
height, adjusting, 24
problems with, 105 to 110
projecting on walls, 40 to 41
raising, 24
selecting source, 20, 34 to 35, 52, 53, 55
size and projection distance, 16, 117
turning off (using A/V Mute), 37
zooming, 25, 38
Image menu, 62 to 65
Input signal, selecting, 20, 34 to 35, 52, 53, 55
Installing projector, 115 to 116
Installing software, 113 to 114
G
K
Group, saving menu settings as, 64
Kensington anti-theft device, 13, 17
Keystone correction, 26 to 27, 65, 108, 117
H
HDTV images, video formats, 120
Height of image, adjusting, 24
Help system, using, 102
Help, Epson, 10, 112
HP OpenView, 79
I
ID setting, 73 to 74
L
Lamp
number of hours used, 105
ordering, 13
replacing, 97 to 100
specifications, 118
status light, 103 to 104
Lamp timer, resetting, 99 to 100
Language setting, 75, 102
Laptop computer
connecting to, 47
display problems, 21 to 23, 105 to 107
selecting source, 20, 47
Lens, cleaning, 95
Lights, status, 103 to 104
Living Room color mode, 62, 66
Logo, saving on projector, 71 to 72
M
Macintosh desktop adapter, 13, 48
130
Index
User's Guide.book Page 131 Tuesday, May 25, 2004 11:49 AM
Manuals, 10
Menus
About, 99 to 100, 105
changing settings, 60 to 61
default settings, restoring, 61
Image, 62 to 65
Signal, 63 to 65
User’s Logo, 71 to 72
Monitor, connecting external, 50
Monitoring projector
EMP Monitor, 81 to 88
HP OpenView, 79
receiving e-mail alerts, 89 to 93
remote setup options, 75
Mouse,
compatibility, 117
connecting cable for remote, 49
using remote control as, 41
N
Network
managing projector remotely, 79 to 93
setting, 85, 87, 91
Network settings, configuring, 80 to 81
New Hardware Wizard, 19
No Signal message, 21, 105 to 107
Noise level, 117
Numeric keypad, using, 69
Positioning
image, 24
projector, 16 to 17
Power
button, 19
specifications, 118
light, 19, 103 to 104
Presentation color mode, 62, 66
Presentations
computer, 20, 28, 46 to 49
room conditions, 32
tips and training, 10
using the pointer tool, 43 to 44
video, 20, 51 to 55
Presenters Online, 10, 112
Preset setting, 64
PrivateLine Support, 11, 112
Problems
color, 110
image, 105 to 110
monitoring projector, 111
no signal, 21, 105 to 107
remote control, 111
sound, 110
using on-screen help, 102
Projecting without screen, 40 to 41
Projection lamp, see Lamp
O
Operation Lock setting, 72
Optical aspect ratio, 117
Options for projector, 13
P
Password
request code, 70
Password protection, 68 to 70
Picture source, selecting, 20, 34 to 35, 52, 53,
55
Picture, see Image
P-in-P image, 38 to 39
Pointer tool, using, 43 to 44
Index 131
User's Guide.book Page 132 Tuesday, May 25, 2004 11:49 AM
Projector
carrying case, 13, 100
cleaning, 95
connections, see Connecting projector
disabling buttons, 72
distance from screen, 16, 117
ID, setting, 73
installing, 115 to 116
lamp specifications, 118
monitoring remotely, 75, 79 to 93
multiple projectors, controlling, 73 to 74
options, 13
password protection, 68 to 70
positioning, 16 to 17
resolution, 117
specifications, 117 to 119
transporting, 100
troubleshooting, 101 to 104
turning off, 29
turning on, 18 to 19
unpacking, 12
viewing information about, 105
Q
Quick Corner, 36
Quick Setup, 76 to 77
R
Raising image, 24
Rear-screen projection, 75, 115 to 116
Registration, 11
132
Index
Remote control
A/V Mute button, 37
as wireless mouse, 41
battery used, 118
checking ID, 74
connecting cable for mouse, 49
correcting color, 40 to 41
E-Zoom button, 38
Freeze button, 37
information, 123
numeric keypad, using, 69
pointer tool, using, 43 to 44
problems, 111, 123
range, 118
replacing batteries, 33
setting ID, 74
specifications, 118
storing, 32
switching sources, 34 to 35
troubleshooting, 111
turning on, 19, 32
Replacing lamp, 97 to 100
Request code, password, 70
Resetting lamp timer, 99 to 100
Resetting menu options, 61
Resize image, 65
Resolution, 64, 117
S
Safety
instructions, 121 to 122
specifications, 119
Screen
blank, 21 to 23
distance from projector, 16
ordering, 13
startup screen, creating, 71 to 72
Screen image, see Image
Security
Kensington lock, 13
password protection, 68 to 70
Sharpness setting, 63
Signal menu, 63 to 65
Sleep mode, 29
User's Guide.book Page 133 Tuesday, May 25, 2004 11:49 AM
SNMP, 79, 80
Software installation, 113 to 114
Sound
adjusting, 67
troubleshooting, 110
Source
selecting, 20, 34 to 35
viewing, 105
Speaker, specifications, 117
Speakers, connecting, 57
Specifications
brightness, 117
dimensions, 118
electrical, 118
environmental, 118
general, 117
lamp, 118
remote control, 118
resolution, 117
safety, 119
sRGB color mode, 63, 66
Standby Mode setting, 75, 85, 87, 91
Startup screen
user’s logo, See User’s Logo
Startup screen, creating, 71 to 72
Status lights, 103 to 104
Support, see Technical support
S-video cable, 13
Switching picture source, 20, 34 to 35
Sync setting, 64
Synchronization, adjusting, 28, 109
T
Technical support, 10, 112
Temperature
requirements, 118
status light, 103 to 104
Theatre color mode, 62, 66
Tone, adjusting, 67
Tracking, adjusting, 28, 109
Transporting projector, 100
Troubleshooting
blank screen, 21 to 23, 105 to 106
cut-off image, 107
distorted image, 26 to 27
EasyManagement, 111
image and sound problems, 105 to 110
no signal, 21, 105 to 107
projector problems, 101 to 104
remote control problems, 111
Turning off picture (using A/V Mute), 37
Turning off projector, 29
U
Unpacking projector, 12
USB cable, 12, 49
User’s Logo menu, 71 to 72
V
VCR, connecting, 51 to 55
Video
cables, 12, 13, 51
connecting video equipment, 51 to 55
display settings, viewing, 105
formats, supported, 119 to 120
selecting source, 20, 34 to 35, 52, 53
Video Signal setting, 65
Volume, adjusting, 67
W
Wall Shot, 40 to 41
Warning lights, 103 to 104
Warranty, 11, 126
Wireless, mouse, 41, 49
Z
Zoom ratio, 117
Zooming image, 25, 38
Index 133
User's Guide.book Page 134 Tuesday, May 25, 2004 11:49 AM
134
Index
Remote Control
Front/Top
E-Zoom button
Enlarges section of image
Control panel
Page Up and Down
Changes slides in PowerPoint
Power button
Turns the projector on and off
Air exhaust vent
A/V buttons
Control image and sound
Speaker
Handle
Light button
Illuminates remote
control buttons
Air filter
Adjustable foot
Enter and Esc
Use as mouse buttons
or to make menu selections
Remote control receiver
and Quick Setup sensor
Lens cover
Menu button
Activates menu system
On/Off switch
Turns the remote control
on and off
Pointer/Mouse button
Moves cursor on the screen
Pointer button
Selects pointer or
drawing tool
Help button
Provides on-screen help
Source buttons
Switch between equipment
connected to projector ports
Back
USB port
(type B)
Computer 2/
Component
and related
audio ports
Ethernet
port
Preview button
Displays active
image sources
Remote control
receiver
Control port for
service use only
Wall Shot button
Corrects color when
projecting on wall
or blackboard
Monitor-out port
Auto button
Optimizes tracking, sync,
resolution, and position
Preset button
Retrieves saved settings
for Video menu
Volume controls
Control sound
Audio-out port
Power inlet
Front adjustable
foot
Video port and
related audio ports
S-Video port and
related audio ports
Computer 1/Component
and related audio ports
Security lock
Num button
Enables number keypad
ID button
Sets remote control ID code
Remote Control
Front/Top
E-Zoom button
Enlarges section of image
Control panel
Page Up and Down
Changes slides in PowerPoint
Power button
Turns the projector on and off
Air exhaust vent
A/V buttons
Control image and sound
Speaker
Handle
Light button
Illuminates remote
control buttons
Air filter
Adjustable foot
Enter and Esc
Use as mouse buttons
or to make menu selections
Remote control receiver
and Quick Setup sensor
Lens cover
Menu button
Activates menu system
On/Off switch
Turns the remote control
on and off
Pointer/Mouse button
Moves cursor on the screen
Pointer button
Selects pointer or
drawing tool
Help button
Provides on-screen help
Source buttons
Switch between equipment
connected to projector ports
Back
USB port
(type B)
Computer 2/
Component
and related
audio ports
Ethernet
port
Preview button
Displays active
image sources
Remote control
receiver
Control port for
service use only
Wall Shot button
Corrects color when
projecting on wall
or blackboard
Monitor-out port
Auto button
Optimizes tracking, sync,
resolution, and position
Preset button
Retrieves saved settings
for Video menu
Volume controls
Control sound
Audio-out port
Power inlet
Front adjustable
foot
Video port and
related audio ports
S-Video port and
related audio ports
Computer 1/Component
and related audio ports
Security lock
Num button
Enables number keypad
ID button
Sets remote control ID code

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project