Marantz | VP-15S1 | User guide | Marantz VP-15S1 User guide

Model VP-15S1 User Guide
DLP® Projector
VP-15S1_U_cover 07.7.5 11:01 AM ページ2
IMPORTANT SAFETY
INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
READ BEFORE OPERATING EQUIPMENT
This product was designed and manufactured to
meet strict quality and safety standards. There are,
however, some installation and operation precautions
which you should be particularly aware of.
1.
Read these instructions.
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the product.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install
in accordance with the manufacture's
instructions.
8.
Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE
LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
NOTE:
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the
equipment and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
9.
10.
Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit
from the apparatus.
11.
Only use attachments/accessories specified
by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or
sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
NOTE:
Changes or modifications not expressly approved
by the party responsible for compliance could void
the user’s authority to operate the equipment.
Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your
safety. If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.
13.
Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14.
Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Additional Safety Information!
• This product should not be placed in a
built-in installation such as a bookcase or
rack unless proper ventilation is provided
or the manufacturer’s instructions have
been adhered to.
• Apparatus shall not be exposed to
dripping or splashing and that no objects
filled as vases, shall be placed on the
apparatus.
• When the switch is in the OFF position,
the apparatus isn’t completely switched-off
from the MAINS.
DECLARATION OF CONFORMITY
This device complies with Part 15 of the FCC rules.
Operation is subject to the following conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
U.S. Responsible Party: Marantz America, Inc.
100 Corporate Drive,
Mahwah, NJ, 07430, U.S.A.
TEL: 630-741-0300
Type of Product: DLP Projector
Model:
VP-15S1
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la Classe B est
conforme à la norme NMB-003 du Canada.
VP-15S1_U_cover 07.7.5 11:01 AM ページ3
ENGLISH
FOREWORD
This section must be read carefully before any
connection is made to the mains supply.
WARRANTY
For warranty information, contact your local
Marantz distributor.
RETAIN YOUR PURCHASE RECEIPT
Your purchase receipt is your permanent record of
a valuable purchase. It should be kept in a safe
place to be referred to as necessary for insurance
purposes or when corresponding with Marantz.
IMPORTANT
When seeking warranty service, it is the
responsibility of the consumer to establish proof
and date of purchase. Your purchase receipt or
invoice is adequate for such proof.
FOR U.K. ONLY
This undertaking is in addition to a consumer’s
statutory rights and does not affect those rights in
any way.
EQUIPMENT MAINS WORKING SETTING
Your Marantz product has been prepared to
comply with the household power and safety
requirements that exist in your area.
COPYRIGHT
Recording and playback of some material may
require permission. For further information refer to
the following:
- Copyright Act 1956
- Dramatic and Musical Performers Act 1958
- Performers Protection Acts 1963 and 1972
- Any subsequent statutory enactments and
orders
WARNINGS
– Do not expose the equipment to rain or
moisture.
– Do not remove the cover from the equipment.
– Do not insert anything into the equipment
through the ventilation holes.
– Do not handle the mains cord with wet
hands.
– Do not cover the ventilation with any items
such as tablecloths, newspapers, curtains,
etc.
– No naked flame sources, such as lighted
candles, should be placed on the equipment.
– When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules that
apply in your country or area.
– Make a space of about 0.2 meter around the
unit.
– When the projector is mounted on the ceiling,
the Ceiling Mount Kit approved by MARANTZ
must be used for installation.
– Do not look into the lens when the projector
is turned on. It could damage your eyesight.
– Unplug the projector from the wall outlet if it
is not to be used for a few days.
– No objects filled with liquids, such as vases,
shall be placed on the equipment.
– When the switch is in the OFF position, the
equipment is not completely switched off
from MAINS.
– The equipment shall be installed near the
power supply so that the power supply is
easily accessible.
Lamp Handing Precautions
DANGER
This SHP uses a high voltage glass mercury vapor
lamp. The lamp can break or fail to light if handled
wrongly during replacement or because of the
projector’s surrounding temperature.
Lamp life also varies according to the lamp with
some even breaking or failing to light as soon as
they are used the first time. If the lamp breaks,
glass fragments may be scattered inside the lamp
unit and projector, and gas inside the lamp bulb
that contains mercury vapor may be emitted from
the projector’s vent.
Before use, carefully read the projector user guide
and the lamp replacement instructions. Remember
to handle the lamp with care. In the event of
serious trouble, call for Marantz authorized dealer.
• Do not look directly into the lamp with bare
eyes while lit. The bright light can cause sore
eyes and impair vision.
• Do not directly expose skin to the light of the
lamp. Direct exposure can inflame the skin.
• Do not drop, impact, subject to excessive force
or otherwise damage the lamp.
• Replacing the lamp runs the risk of burns and
electric shock, therefore shut OFF power
supply, unplug the AC power cord from AC
power outlet and wait at least 60 minutes for
the lamp to cool down before attempting to
replace it.
• If the lamp breaks, unplug the AC power cord
from AC power outlet and call for Marantz
authorized dealer to replace it. Do not replace
the lamp yourself or clean up broken glass
inside the projector as this can result in cuts
and burns to you or damages inside the
projector.
• If the projector is hung from a ceiling or
installed in a high place, it is extremely
dangerous to replace the lamp. In this case, do
not replace or handle the damaged lamp
yourself.
CAUTION
• The chance of the lamp breaking is high after
extended use. It is recommended to replace
the lamp when near the end of its designed
life. Do not use a lamp beyond the maximum
lighting time.
• Use only Marantz original lamp units. Check
the model code of the lamp unit matches that
in the user guide.
• Before replacing the lamp, read carefully
“Lamp Unit Replacement” in the user guide.
Replace the lamp as explained therein.
• Entrust disposal of a used lamp to a licensed
industrial waste handler or return it to the place
of purchase. Do not break the lamp or discard
with general waste.
• If the lamp breaks, leave the area immediately
and stay away for at least 30 minutes, and
ventilate the room so as not to inhale the
mercury vapor.
• If you inhale the mercury vapor, see a
physician immediately and follow his
instructions.
VP-15S1_U_cover 07.7.5 11:01 AM ページ4
FRANÇAIS
AVANT-PROPOS
Prière de lire ce chapitre avant de brancher
l’appareil sur le secteur.
GARANTIE
Pour des informations sur la garantie, contacter le
distributeur local Marantz.
CONSERVER L’ATTESTATION D’ACHAT
L’attestation d’achat est la preuve permanente d’un
achat de valeur. La conserver en lieu sur pour s’y
reporter aux fins d’obtention d’une couverture
d’assurance ou dans le cadre de correspondances
avec Marantz.
IMPORTANT
Pour l’obtention d’un service couvert par la
garantie, il incombe au client d’établir la preuve de
l’achat et d’en corroborer la date. Le reçu ou la
facture constituent des preuves suffisantes.
REGLAGE DE L’ALIMENTATION
SECTEUR DE L’APPAREIL
Cet appareil Marantz a été conçu pour respecter
les exigences de votre région en matière
d’alimentation secteur et de sécurité.
DRUITS D' AUTEUR
L’enregistrement et la lecture de certaines
informations sonores nécessitent une autorisation.
Pour de plus amples renseignements, consultez:
- La loi de 1956 sur les Copyright
- Loi concernant les Acteurs et Musiciens 1958
- Lois de Protection des Artistes 1963 et 1972
- Les décrets et règlements ultérieurs qui s’y
rapportent
AVERTISSEMENTS
– Ne pas exposer l’appareil à la pluie ni à
l’humidité.
– Ne pas essayer de retirer le boîtier de
l’appareil.
– Ne rien insérer dans l’appareil par les orifices
de ventilation.
– Ne pas manipuler le cordon d’alimentation
avec les mains mouillées.
– Ne pas recouvrir les ouïes de ventilation avec
un objet quelconque comme une nappe, un
journal, un rideau, etc.
– Ne placer aucune source de flamme nue,
comme une bougie allumée, sur l'appareil.
– Pour mettre au rebut les piles usées,
respecter les lois gouvernementales ou les
règlements
officiels
concernant
l’environnement qui s'appliquent à votre pays
ou région.
– Veiller à ce qu’aucun objet ne soit à moins de
0,2 mètre des côtés de l'appareil.
– Pour monter le projecteur au plafond, vous
devez utiliser un kit de montage au plafond
approuvé par MARANTZ pour l'installation.
– Ne regardez pas dans l'objectif quand le
projecteur est allumé. Cela pourrait
endommager votre vue.
– Débranchez le projecteur de la prise murale
s'il ne doit pas être utilisé pendant plusieurs
jours.
– Aucun objet rempli de liquide, un vase par
exemple, ne doit être placé sur l'appareil.
– Lorsque l'interrupteur est sur la position OFF,
l'appareil n'est pas complètement
déconnecté du SECTEUR (MAINS).
– L'appareil sera installé près de la source
d'alimentation, de sorte que cette dernière
soit facilement accessible.
Précautions à prendre pour la
manipulation de la lampe
DANGER
Ce SHP utilise une lampe à vapeur de mercure en
verre à haute tension. Cette lampe peut se casser
ou ne pas s'allumer si elle est manipulée
incorrectement pendant son remplacement ou du
fait de la température ambiante du projecteur.
La durée de service d'une lampe varie aussi en
fonction de la lampe, certaines se cassant ou ne
s'allumant pas aussitôt qu'elles sont utilisées pour
la première fois. Si la lampe se casse, des
fragments de verre peuvent se répandre à
l'intérieur de l'unité lampe et du projecteur, et le
gaz à l'intérieur de l'ampoule de la lampe qui
contient de la vapeur de mercure peut être émis
par l'orifice du projecteur.
Avant utilisation, lisez attentivement le guide de
l'utilisateur du projecteur et les instructions de
remplacement de la lampe. Pensez à manipuler la
lampe avec précautions. En cas de problème
sérieux, contactez un distributeur agréé Marantz.
• Ne regardez pas directement la lampe sans
protection pour les yeux pendant qu'elle est
allumée. Sa lumière brillante peut faire mal aux
yeux et affaiblir la vue.
• N'exposez pas directement la peau à la
lumière de la lampe. Une exposition directe
peut provoquer une inflammation de la peau.
• Ne laissez pas tomber la lampe, ne la heurtez
pas, ne la soumettez pas à une force excessive
ni ne l'endommager.
• Le remplacement de la lampe fait courir un risque
de brûlure et de choc électrique ; il faut donc
couper l'alimentation électrique, débrancher le
cordon d'alimentation secteur de la prise secteur
et attendre au moins 60 minutes que la lampe
refroidisse avant d'essayer de la remplacer.
• Si la lampe se casse, débranchez le cordon
d'alimentation secteur de la prise secteur et
contactez un distributeur agréé Marantz pour
qu'il la remplace. Ne remplacez pas la lampe
vous-même ni ne nettoyez le verre brisé à
l'intérieur du projecteur car vous pourriez vous
couper et vous brûler ou endommager
l'intérieur du projecteur.
• Si le projecteur est accroché au plafond ou
installé dans un endroit en hauteur, il est
extrêmement dangereux de remplacer la lampe.
Dans ce cas, ne remplacez ni ne manipulez
vous-même la lampe endommagée.
ATTENTION
• Le risque que la lampe se casse est élevé
après une utilisation prolongée. Il est
recommandé de remplacer la lampe
lorsqu'elle approche de sa durée de service
spécifiée. N'utilisez pas une lampe au-delà du
temps d'éclairage maximum.
• N'utilisez que des unités lampes d'origine
Marantz. Vérifiez que le code de modèle de
l'unité lampe correspond à celui indiqué dans le
guide de l'utilisateur.
• Avant de remplacer la lampe, lisez
attentivement "Remplacement de l'unité
lampe" dans le guide de l'utilisateur.
Remplacez la lampe conformément aux
explications de cette section.
• Confiez la mise au rebut d'une lampe usée à
un service de déchets industriels licencié ou
retournez-la où vous l'avez achetée. Ne
cassez pas la lampe ni ne la jetez avec les
ordures ménagères.
• Si la lampe se casse, sortez immédiatement
de la zone pendant au moins 30 minutes, et
aérez la pièce afin de ne pas inhaler la vapeur
de mercure.
• Si vous inhalez de la vapeur de mercure,
consultez immédiatement un médecin et
suivez ses instructions.
VP-15S1_U_cover 07.7.5 11:01 AM ページ5
ESPAÑOL
PROLOGO
Antes de conectar el equipo a la corriente, debe
leer este capítulo.
GARANTIA
Para obtener información acerca de la garantia
póngase en contacto con su distribuidor Marantz.
GUARDE SU RECIBO DE COMPRA
Su recibo de compra es su prueba permanente de
haber adquirido un aparato de valor, Este recibo
deberá guardarlo en un lugar seguro y utilizarlo
como referencia cuando tenga que hacer uso del
seguro o se ponga en contacto con Marantz.
IMPORTANTE
Cuando solicite el servicio otorgado por la garantia
el usuario tiene la responsabilidad de demonstrar
cuando efectuó la compra. En este caso, su recibo
de compra será la prueba apropiada.
SELECCION DEL VOLTAJE DE
ALIMENTACION
Este producto Marantz se ha preparado para estar
conforme con los requisitos de alimentación
eléctrica doméstica y de seguridad que hay en su
zona.
COPYRIGHT
La grabación y reproducción de determinado
material puede necesitar permiso. Para más
información consulte lo siguiente:
- Acta sobre copyright de 1958
- Acta de la Sociedad General de Autores de
1958
- Acta de Protección de la Propiedad
Intelectual de Autores de 1963 y 1972
- Cualquier acta, estatuto y órdenes
subsiguientes
ADVERTENCIAS
– No exponga el equipo a la lluvia ni a la
humedad.
– No extraiga la tapa del equipo.
– No introduzca nada en el interior del equipo a
través de los orificios de ventilación.
– No maneje el cable de alimentación con las
manos mojadas.
– No cubra la ventilación con objetos como
manteles, periódicos, cortinas, etc.
– No deben colocarse sobre el equipo
elementos con fuego, por ejemplo velas
encendidas.
– Cuando se eliminen baterías usadas, deben
cumplirse las reglamentaciones oficiales o
las normas de protección medioambiental
aplicables en su país o en su zona.
– Deje un espacio de unos 0,2 metro alrededor
de la unidad.
– Cuando el proyector se monte en el techo
deberá utilizarse para la instalación el juego
de montaje en el techo aprobado por
MARANTZ.
– No mira al objetivo cuando el proyector esté
encendido. Podría lesionarse la vista.
– Desenchufe el proyector de la toma de
corriente si no lo va a utilizar durante unos
pocos días.
– No se deben colocar sobre el aparato
recipientes que contengan líquidos, como por
ejemplo jarrones.
– Cuando el interruptor está en la posición
OFF, el equipo no está completamente
desconectado de la alimentación MAINS.
– El equipo se instalará cerca de la fuente de
alimentación de manera que resulte fácil
acceder a ella.
Precauciones para la manipulación de la
lámpara
PELIGRO
Esta lámpara SHP de vidrio y de alto voltaje
contiene vapor de mercurio. La lámpara puede
romperse o no encenderse si es manipulada
incorrectamente durante el recambio o debido a la
temperatura ambiente del proyector.
La vida útil también varía según las lámparas,
algunas de las cuales se rompen o no se
encienden al cabo del primer uso. Si la lámpara se
rompe, los fragmentos de cristal se pueden
desparramar por el interior de la unidad de la
lámpara y del proyector, y el gas con vapor de
mercurio contenido en la bombilla se puede
escapar a través del sistema de ventilación del
proyector.
Antes de usar el aparato, lea con cuidado la guía
de usuario del proyector y las instrucciones de
recambio de la lámpara. No olvide manipular con
cuidado la lámpara. En caso de producirse
problemas serios, avise a un distribuidor
autorizado de Marantz.
• No mire directamente a la lámpara sin
protección en los ojos cuando ésta esté
encendida. La luz brillante puede irritar los ojos
e impedir la visión.
• No exponga directamente la piel a la luz de la
lámpara. La exposición directa puede inflamar
la piel.
• No deje caer la lámpara, ni la golpee, ni la
someta a presiones excesivas, ya que de lo
contrario la lámpara se daña.
• El recambio de la lámpara entraña el riesgo de
quemaduras y descargas eléctricas, y por lo
tanto, deberá apagar el aparato, desenchufar
el cable de alimentación del tomacorriente de
CA, y esperar al menos 60 minutos a que la
lámpara se enfríe antes de intentar
recambiarla.
• Si la lámpara se rompe, desenchufe el cable de
alimentación de CA y avise a un distribuidor
autorizado de Marantz para recambiarla. No
recambie la lámpara usted mismo ni limpie los
cristales rotos en el interior del proyector, pues
podría sufrir cortes y quemaduras y ocasionar
daños en el interior del proyector.
• Si el proyector cuelga del techo o está instalado
en un lugar elevado, el recambio de la lámpara
es extremadamente peligroso. En tal caso, no
recambie ni manipule usted mismo la lámpara
dañada.
PRECAUCIÓN
• La probabilidad de que la lámpara se rompa
es alta después de un uso prolongado. Se
recomienda recambiar la lámpara cerca de la
fecha de expiración de su vida útil prevista.
No utilice una lámpara más tiempo del
máximo de iluminación previsto.
• Utilice sólo lámparas originales de Marantz.
Compruebe que el código del modelo de la
lámpara coincide con el de la guía de usuario.
• Antes de recambiar la lámpara, lea
atentamente la sección “Recambio de la
lámpara” en la guía de usuario. Recambie la
lámpara tal y como viene allí explicado.
• Confíe el desecho de la lámpara usada a un
manipulador autorizado de desechos
industriales o devuélvala al lugar donde la
compró. No rompa la lámpara ni la deseche
en la basura normal.
• Si la lámpara se rompe, abandone la zona
inmediatamente y permanezca alejado
durante al menos 30 minutos, ventilando la
habitación con objeto de no inhalar el vapor
de mercurio.
• Si inhala vapor de mercurio, consulte
inmediatamente a su médico y siga sus
instrucciones.
VP-15S1_U_cover 07.7.5 11:01 AM ページ6
PORTUGUÊS
INTRODUÇÃO
Esta secção deverá ser lida antes de efectuar
qualquer ligação àcorrente.
GARANTIA
Para informações sobre a garantia, contactar o
distribuidor Marantz local.
GUARDAR O RECIBO DE COMPRA
O recibo é o registo permanente da compra que
fez. Deve ser guardado num local seguro, para ser
apresentado em questões relacionadas com o
seguro ou para quando tiver de contactar a
Marantz.
IMPORTANTE
Quando procurar assisténcia técnica ao abrigo da
garantia, é da responsabilidade do consumidor
estabelecer a prova e data de compra. O recibe é
prova adequada.
REGULAÇÃO DO EQUIPAMENTO
CONFORME A ALIMENTAÇÃO DA REDE
O seu produto Marantz foi condicionado a
satisfazer os requisitos domésticos de energia e
segurança existentes na sua zona.
DIREITOS DE AUTOR
Poderá ser necessária autorização para a
gravação e a leitura de determinado material. Para
mais informações deverá consultar o seguinte:
- Lei do direito de autor de 1956 (Copyright
Act)
- Lei dos artistas relacionados com a música e
com o teatro de 1958 (Dramatic and Musical
Performers Act)
- Leis de protecção dos artistas de 1963 e de
1972 (Performers Protection Acts)
- Quaisquer regulamentos e despachos
estatutários posteriores
ADVERTÊNCIAS
– Não exponha o equipamento à chuva nem à
humidade.
– Não retire a tampa do equipamento.
– Não atire nada para dentro do equipamento
através dos orificíos de ventilação.
– Não manuseie o cabo de alimentação com
as mãos molhadas.
– Não cobrir os orifícios de ventilação com
objectos tais como toalhas de mesa, jornais,
cortinas, etc.
– Não colocar chamas abertas tais como velas
acesas, sobre o aparelho.
– Ao deitar foras as pilhas usadas, favor
observar os regulamentos governamentais
ou as regras com respeito ao meio ambiente
que se aplicam no seu país ou área de
residência.
– Deixar um espaço de cerca de 0,2 metro ao
redor do aparelho.
– Quando o projector for montado no tecto, o
Kit de Montagem no Tecto aprovado pela
MARANTZ deverá ser utilizado para a
instalação.
– Não olhe para dentro da lente quando o
projector é activado. Isto pode danificar a
visão.
– Desligue o projector da tomada de parede se
este não estiver para ser utilizado durante
alguns dias.
– Não colocar recipientes com água, tal como
vasos, sobre o aparelho.
– Quando o interruptor está na posição OFF, o
equipamento não fica totalmente desligado
de MAINS.
– O aparelho deve ser instalado próximo a
uma tomada de energia para fácil acesso.
Precauções para o manuseio da lâmpada
CUIDADO
Esta lâmpada SHP é uma lâmpada feita de vidro
que contém vapor de mercúrio a alta pressão. A
lâmpada pode quebrar ou não acender caso seja
manuseada incorrectamente durante a
substituição ou devido à temperatura ambiente
onde se encontra o projector.
A vida útil da lâmpada também varia conforme a
lâmpada, com casos de quebra ou falha em
acender na primeira vez que a lâmpada é utilizada.
Se a lâmpada quebrar, estilhaços de vidro podem
cair dentro do compartimento da lâmpada e do
projector, e o gás de dentro da lâmpada que
contém vapor de mercúrio poderá ser emitido
através da saída do projector.
Antes de o utilizar, leia cuidadosamente o guia do
utilizador do projector bem como as instruções
para substituição da lâmpada. Lembre-se de
manusear a lâmpada com cuidado. No caso de
problemas, entre em contacto com o representante
autorizado da Marantz.
• Não olhar directamente na lâmpada acesa
sem protecção ocular. A luz forte pode causar
irritação nos olhos ou prejudicar a visão.
• Não expor a pele directamente à luz da
lâmpada. Exposição directa pode causar
inflamação na pele.
• Não derrubar, bater, nem usar força excessiva,
pois pode danificar a lâmpada.
• Devido ao risco de queimaduras e choque
eléctrico ao substituir a lâmpada, desligue a
alimentação, desligue o cabo de alimentação da
tomada de CA e espere pelo menos 60 minutos
para arrefecer antes de substituir a lâmpada.
• Se a lâmpada quebrar, desligue o cabo de
alimentação de CA da tomada e entre em
contacto com o representante autorizado da
Marantz para que faça a substituição. Não
tente fazer a substituição nem limpar os
estilhaços de vidro de dentro do projector, pois
pode resultar em cortes e queimaduras ou
ainda danos ao projector.
• Se o projector estiver instalado no teto ou
qualquer lugar alto, é extremamente perigoso
substituir a lâmpada. Nesse caso, não tente
fazer a substituição nem manusear o lâmpada
danificada.
AVISO
• A probabilidade da lâmpada quebrar aumenta
depois de um longo período de utilização. É
recomendável substituir a lâmpada quando a
vida útil da mesma estiver próxima do fim.
Não utilizar a lâmpada além do tempo máximo
determinado.
• Utilizar apenas lâmpadas genuínas Marantz.
Confirme que o código do modelo da lâmpada
corresponde com o listado no guia do
utilizador.
• Antes de substituir a lâmpada, leia
cuidadosamente a secção “Substituição da
lâmpada” no guia do utilizador. Substitua a
lâmpada de acordo com as instruções dadas.
• Para jogar uma lâmpada usada, solicite os
serviços de uma companhia autorizada a
colectar lixo industrial ou devolva a lâmpada na
loja onde a adquiriu. Não quebrar a lâmpada
nem jogá-la com o lixo comum.
• Se a lâmpada quebrar, saia da sala
imediatamente, ventile o ambiente para evitar
inalar o vapor de mercúrio e não retorne por
pelo menos 30 minutos.
• Se inalar o vapor de mercúrio, consulte um
médico imediatamente e siga as suas
instruções.
VP-15S1_U_cover 07.7.5 11:01 AM ページ7
DEUTSCH
VORWORT
Dieser Abschnitt muß gelesen werden, bevor das
Gerät an eine Netzsteckdose angeschlossen wird.
GARANTIE
Bei Garantiefragen wenden Sie sich bitte an Ihren
Marantz-Händler.
HEBEN SIE IHRE QUITTING GUT AUF
Die Quittung dient Ihnen als bleibende Unterlage
für Ihren wertvollen Einkauf Das Aufbewahren der
Quittung ist wichtig, da die darin enthaltenen
Angaben für Versicherungswecke oder bei
Korrespondenz mit Marantz angeführt werden
müssen.
WICHTIG!
Bei Garantiefragen muß der Kunde eine
Kaufunterlage mit Kaufdatum vorlegen. Ihren
Quittung oder Rechnung ist als Unterlage
ausreichend.
NETZSPANNUNGS-EINSTELLUNG DES
GERÄTES
Dieses Marantz-Produkt entspricht den
Netzspannungs- und Sicherheitsanforderungen,
die im Vertriebsgebiet gelten.
VP-12S4 kann nur mit einer Spannung von 230 V
AC betrieben werden.
COPYRIGHT
Für die Aufnahme und Wiedergabe von gewissen
Materialien kann eine Genehmigung erforderlich
sein. Die folgenden Vorschriften müssen beachtet
werden:
- Copyright Act 1956
- Dramatic and Musical Performers Act 1958
- Performers Protection Acts 1963 and 1972
- Jegliche nachfolgenden Gesetze und
Vorschriften
WARNHINWEISE
– Das Gerät nicht Regen oder Feuchtigkeit
aussetzen.
– Die Abdeckung nicht vom Gerät abnehmen.
– Keine
Gegenstände
durch
die
Belüftungsschlitze stecken.
– Das Netzkabel nicht mit feuchten oder
nassen Händen anfassen.
– Decken Sie die Lüftungsöffnungen nicht mit
einem Tischtuch, einer Zeitung, einem
Vorhang usw. ab.
– Es dürfen keine Gegenstände mit offener
Flamme, wie etwa brennende Kerzen, auf
dem Gerät aufgestellt werden.
– Beachten Sie bei der Entsorgung der
verbrauchten Batterien alle geltenden lokalen
und überregionalen Regelungen.
– Auf allen Geräteseiten muß ein
Zwischenraum von ungefähr 0,2 meter
vorhanden sein.
– Wenn der Projektor an der Decke montiert
werden soll, muß der von MARANTZ
vorgesehene Einbauteilesatz für die
Deckenmontage verwendet werden.
– Bei eingeschaltetem Projektor nicht in das
Objektiv schauen. Bei Nichtbeachtung
können Augenschäden die Folge sein.
– Wenn der Projektor mehrere Tage nicht
verwendet werden soll, ist der Stecker aus
der Wandsteckdose herauszuziehen.
– Auf das Gerät dürfen keine mit Flüssigkeiten
gefüllte Behälter, wie etwa eine Vase, gestellt
werden.
– Wenn der Schalter ausgeschaltet ist (OFFPosition), ist das Gerät nicht vollständig vom
Stromnetz (MAINS) abgetrennt.
– Das Gerät sollte in der Nähe einer
Netzsteckdose aufgestellt werden, damit es
leicht an das Stromnetz angeschlossen
werden kann.
Sicherheitsvorkehrungen zum Umgang
mit der Lampe
GEFAHR
Dieser Projektor verwendet SHP-Lampe, eine
Hochspannungsglaslampe mit Quecksilberdampf.
Die Lampe kann zerbrechen oder unter
Umständen nicht leuchten, falls Sie sie beim
Austauschen falsch handhaben oder infolge der
Umgebungstemperatur des Projektors.
Die Lampenlebensdauer variiert je nach Lampe,
wobei einige Lampen möglicherweise gleich bei der
ersten Verwendung zerbrechen oder nicht leuchten.
Falls eine Lampe zerbricht, können die Scherben in
der Lampeneinheit und im Projektor verstreut werden;
außerdem kann das durch das Zerbrechen der Lampe
freigesetzte Gas, das Quecksilberdampf enthält, durch
die Entlüftungsöffnungen des Projektors ausströmen.
Lesen Sie die Bedienungsanleitung des Projektors und
die Anleitungen zum Austauschen der Lampe vor der
ersten Inbetriebnahme aufmerksam durch. Bedenken
Sie bitte, dass sorgfältige Handhabung gefragt ist.
Sollten ernste Probleme auftreten, wenden Sie sich
bitte an einen autorisierten Marantz-Fachhändler.
• Sehen Sie nicht mit den bloßen Augen direkt in
die leuchtende Lampe. Das helle Licht der
Lampe kann zu schmerzenden Augen führen
und die Sehkraft beeinträchtigen.
• Achten Sie darauf, dass das Licht der Lampe
nicht direkt auf Ihre Haut trifft. Trifft das Licht
direkt auf Ihre Haut, kann sich diese entzünden.
• Lassen Sie die Lampe nicht fallen, stoßen Sie
sie nicht an, setzen Sie sie keine allzu großen
Kraftanwendung aus, und beschädigen Sie sie
auch sonst nicht.
• Beim Austauschen der Lampe besteht die
Gefahr von Verbrennungen und Stromschlag.
Schalten Sie den Projektor daher aus, ziehen
Sie das Netzkabel aus der Steckdose und
warten Sie mindestens 60 Minuten, damit sich
die Lampe auskühlt, bevor Sie sie austauschen.
• Falls die Lampe zerbricht, ziehen Sie das
Netzkabel aus der Steckdose und wenden Sie
sich an einen autorisierten MarantzFachhändler, um die Lampe austauschen zu
lassen. Versuchen Sie nicht selbst, die Lampe
auszutauschen bzw. das zerbrochene Glas
aus dem Projektor zu entfernen, da Sie sich
dabei schneiden oder verbrennen bzw. das
Projektorinnere beschädigen könnten.
• Falls der Projektor an eine Decke gehängt
oder an einem hoch gelegenen Ort installiert
wird, ist das Austauschen der Lampe
besonders gefährlich. Versuchen Sie in diesem
Fall nie, die beschädigte Lampe selbst
auszutauschen oder zu handhaben.
VORSICHT
• Nach langem Gebrauch ist die Gefahr, dass
die Lampe zerbricht, groß. Wir empfehlen, die
Lampe gegen Ende ihrer festgelegten
Lebensdauer auszutauschen. Verwenden Sie
die Lampe nicht nach ihrer maximalen
Beleuchtungslebensdauer.
• Verwenden Sie nur die originellen MarantzLampeneinheiten. Überprüfen Sie, ob der
Modellcode der Lampeneinheit mit dem in der
Bedienungsanleitung angeführten Code
übereinstimmt.
• Lesen Sie vor dem Austauschen der Lampe
den
Abschnitt
“Austauschen
der
Lampeneinheit” aufmerksam durch. Tauschen
Sie die Lampe so aus, wie es in diesem
Abschnitt beschrieben ist.
• Entsorgen Sie die Lampe gemäß den
geltenden Umweltschutzregelungen bzw.
bringen Sie in das Geschäft zurück, in dem Sie
sie erworben haben. Zerbrechen Sie die
Lampe nicht, um sie mit dem normalen
Hausmüll zu entsorgen.
• Sollte die Lampe zerbrechen, verlassen Sie
den Arbeitsbereich unverzüglich und bleiben
Sie mindestens 30 Minuten von diesem Ort
fern. Entlüften Sie den Raum gut, um den
Quecksilberdampf nicht einzuatmen.
• Sollten Sie versehentlich Quecksilberdampf
einatmen, suchen Sie unverzüglichen einen
Arzt auf und befolgen Sie seine Anweisungen.
VP-15S1_U_cover 07.7.5 11:01 AM ページ8
ITALIANO
INTRODUZIONE
Leggete questa sezione prima di effettuare
qualsiasi collegamento con la rete.
GARANZIA
L’apparecchio è coperto da una garanzia di buon
funzionamento della durata di un anno, o del
periodo previsto dalla legge, a partire dalla data di
acquisto comprovata da un documento attestante il
nominativo del Rivenditore e la data di vendita. La
garanzia sarà prestata con la sostituzione o la
riparazione gratuita delle parti difettose.
Non sono coperti da garanzia difetti derivanti da
uso improprio, errata installazione, manutenzione
effettuata da personale non autorizzato o,
comunque, da circostanze che non possano
riferirsi a difetti di funzionamento dell’apparecchio.
Sono inoltre esclusi dalla garanzia gli interventi
inerenti l’installazione e l’allacciamento agli
impianti di alimentazione.
Gli apparecchi verranno riparati presso i nostri
Centri di Assistenza Autorizzati. Le spese ed i
rischi di trasporto sono a carico del cliente.
La casa costruttrice declina ogni responsabilità per
danni diretti o indiretti provocati dalla inosservanza
delle prescrizioni di installazione, uso e
manutenzione dettagliate nel presente manuale o
per guasti dovuti ad uso continuato a fini
professionali.
REGOLAZIONE DELLA TENSIONE DI
FUNZIONAMENTO DELL’APPARECCHIO
Il vostro apparecchio Marantz è stato predisposto
per l’adattamento alla tensione ed alle norme di
sicurezza esistenti nella vostra zona.
VP-12S4 può essere alimentato soltanto da
corrente alternata a 230 V.
DIRITTI D’AUTORE
La registrazione e la riproduzione di certi materiali
necessita di un permesso.
Per ulteriori informazioni consultate quanto segue:
- Copyright Act 1956
- Dramatic and Musical Performers Act 1972
- Qualsiasi legge o normativa successiva
AVVERTENZE
– Non esporre l’apparecchio alla pioggia o
all’umidità.
– Non rimuovere il coperchio dell’apparecchio.
– Non
introdurre
oggetti
all’interno
dell’apparecchio attraverso i fori di
ventilazione.
SUOMI
– Non toccare il cavo di alimentazione con le
mani bagnate.
– Non coprire le fessure di ventilazione con
tovaglie, giornali, tende od oggetti analoghi.
– Non posare sull'apparecchio sorgenti di
fiamme scoperte quali candele accese.
– Smaltire le pile usate in conformità alle
norme governative o disposizioni ambientali
vigenti nel proprio paese o zona.
– Lasciare 0,2 metro liberi tutto intorno l'unità.
– Se il proiettore viene montato sul soffitto, si
deve usare per l'installazione il Corredo di
installazione sul soffitto della MARANTZ.
– Non guardare nel proiettore quando questo è
acceso. Ciò può danneggiarvi la vista.
– Se si prevede di non doverlo usare per
qualche tempo, scollegare il proiettore dalla
presa di corrente.
– Non mettere sull'apparecchiatura alcun
contenitore di liquido, come ad esempio dei
vasi.
– Quando l'interruttore è nella posizione OFF,
l'apparecchiatura non è completamente
scollegata da MAINS.
– L’apparecchio va installato in prossimità della
fonte di alimentazione, in modo che
quest’ultima sia facilmente accessibile.
Precauzioni d'uso della lampada
PERICOLO
Questa è una lampada SHP di vetro a vapori di
mercurio ad alta tensione. Potrebbe rompersi o
guastarsi se non viene maneggiata correttamente
durante la sostituzione o se il proiettore è soggetto
a una temperatura eccessiva.
La durata delle lampade è variabile ed alcune
potrebbero addirittura rompersi o non accendersi la
prima volta che vengono utilizzate. Se la lampada
si rompe, le schegge di vetro potrebbero venire
sparse all'interno dell'unità lampada e del
proiettore e il gas all'interno della lampada, che
contiene vapori di mercurio, potrebbe essere
espulso dalle aperture di ventilazione del
proiettore.
Prima dell'uso, leggere con attenzione la guida
d'uso del proiettore e le istruzioni di sostituzione
della lampada. Maneggiare sempre la lampada
con attenzione. Nel caso di guasti gravi, rivolgersi
al rivenditore autorizzato Marantz.
• Non guardare direttamente verso la lampada
accesa a occhio nudo. La luce intensa può
abbagliare e danneggiare la vista.
• Non esporre direttamente la pelle alla luce
della lampada. L'esposizioni diretta potrebbe
irritare la pelle.
• Non far cadere, urtare o sottoporre a forza
eccessiva, altrimenti si guasta la lampada.
• La sostituzione della lampada comporta il
rischio di bruciature e scosse elettriche, perciò
prima di sostituirla, spegnere l'alimentazione,
scollegare il cavo di alimentazione c.a. dalla
corrispondente presa e attendere almeno 60
minuti che la lampada si raffreddi.
• Se la lampada si rompe, scollegare il cavo di
alimentazione c.a. dalla corrispondente presa
e chiamare il rivenditore autorizzato Marantz
affinché la sostituisca. Non sostituirla
personalmente, né raccogliere le schegge di
vetro nel proiettore per non subire tagli o
bruciature e non danneggiare l'interno del
proiettore.
• Se il proiettore è appeso al soffitto o installato
in una posizione elevata, è molto pericoloso
sostituire la lampada. In questo caso, non
sostituire o maneggiare la lampada guasta
personalmente.
ATTENZIONE
• La probabilità che la lampada si rompa è
elevata dopo che è stata usata per molto
tempo. Si consiglia di sostituire la lampada
quando si avvicina al termine della vita utile.
Non usare la lampada oltre il limite della vita
utile.
• Usare unicamente lampade Marantz originali.
Verificare che il codice del modello dell'unità
lampada corrisponda a quello indicato nella
guida dell'utente.
• Prima di sostituire la lampada, leggere con
attenzione "Sostituzione dell'unità lampada"
nella guida per l'utente. Sostituire la lampada
come indicato in tali istruzioni.
• Incaricare dello smaltimento della lampada
usata un apposito servizio di smaltimento di
rifiuti industriali oppure restituirla al rivenditore.
Non rompere la lampada o gettarla con i rifiuti
normali.
• Se la lampada si rompe, lasciare il locale
immediatamente e non farvi ritorno per almeno
30 minuti; arieggiare il locale in modo da non
inalare i vapori di mercurio.
• Se vengono inalati i vapori di mercurio,
rivolgersi immediatamente a un medico e
seguirne le istruzioni.
VARO
Laite on liitettava suojamaadoitus-koskettimilla
varustettuun pistorasiaan.
KONGERIKET NORGE
FORSIKTIG
Apparatet ma tilkoples jordet stikkontakt.
SVENSKA
OBSERVERA
Apparaten skall anslutas till jordat uttag.
TABLE OF CONTENTS
IMPORTANT SAFEGUARDS ................................................................................................2
Caution Concerning the Setup of the Projector........................................................................2
Caution Concerning the Lamp Replacement ...........................................................................2
Caution Concerning the Lamp Unit ..........................................................................................2
Notes on Operation ...................................................................................................................2
FEATURES ............................................................................................................................3
ACCESSORIES......................................................................................................................3
PROJECTOR LAYOUT AND FUNCTIONAL OVERVIEW ....................................................4
Front and Top View ...................................................................................................................4
Rear and Terminals View ..........................................................................................................5
Bottom View ..............................................................................................................................5
Remote Controller .....................................................................................................................6
Remote Controller Operational Range ......................................................................................8
Preparing the Remote Controller...............................................................................................8
CONNECTION........................................................................................................................9
Connection with AC Power Supply............................................................................................9
Connection with Video Equipments...........................................................................................9
Connection with a HD-Video, DVD Player, Satellite, Cable Tuner or PC................................10
Advanced Connection .............................................................................................................10
INITIAL SETTING.................................................................................................................11
Turning on the Power ..............................................................................................................11
Zooming and Focusing............................................................................................................11
Detail Focusing........................................................................................................................11
Adjusting the Image Position...................................................................................................12
Adjusting the Height ................................................................................................................12
Keystone Correction................................................................................................................12
INSTALLATION ...................................................................................................................13
Recommended Setting............................................................................................................13
Screen Size and Projection Distance (inch) VP-15S1............................................................14
Screen Size and Projection Distance (mm) VP-15S1 ............................................................14
Screen Size and Projection Distance (inch) VP-15S1L..........................................................15
Screen Size and Projection Distance (mm) VP-15S1L ..........................................................15
Lens shift position VP-15S1 ...................................................................................................16
Lens shift position VP-15S1L .................................................................................................17
BASIC OPERATIONS..........................................................................................................18
Turning on the Power ..............................................................................................................18
Selecting the Input Signal Source ...........................................................................................18
Selecting the Aspect Mode......................................................................................................18
The Screen Images in a 16:9 screen ......................................................................................19
The Screen Images in a 4:3 screen ........................................................................................20
To Turn off the Power..............................................................................................................20
OPERATIONS ......................................................................................................................21
Menu Structure........................................................................................................................21
Functions by Signal .................................................................................................................22
Picture Mode ...........................................................................................................................24
How to Operate Menus ...........................................................................................................24
Picture Adjust ..........................................................................................................................25
Fine Menu 1 ............................................................................................................................26
Fine Menu 2 ............................................................................................................................26
Input Signal .............................................................................................................................27
RGB/HD Adjust .......................................................................................................................27
HDMI .......................................................................................................................................28
Display.....................................................................................................................................28
OSD/Blanking..........................................................................................................................29
Configration .............................................................................................................................30
MAINTENANCE ...................................................................................................................31
Lamp Life and Replace Lamp .................................................................................................31
Replacing Lamp Unit ...............................................................................................................31
Cleaning the Lens ...................................................................................................................33
Replacement Parts..................................................................................................................33
Optional Accessories...............................................................................................................33
TROUBLESHOOTING .........................................................................................................34
ERROR MODE .....................................................................................................................35
ON SCREEN MESSAGE .....................................................................................................35
GLOSSARY..........................................................................................................................35
SPECIFICATIONS................................................................................................................36
DIMENSIONS .......................................................................................................................37
VP-15S1 ..................................................................................................................................37
VP-15S1L ................................................................................................................................37
– For Europe –
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. This product and
the accessories packed together are the applicable product to the WEEE directive except
batteries.
Please dispose of any materials in accordance with your local recycling regulations.
When discarding the unit, comply with your local rules or regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with
your local regulations concerning chemical wastes.
1
ENGLISH
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ1
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ2
Caution
ENGLISH
IMPORTANT SAFEGUARDS
Caution
For minimal servicing and to maintain high image quality, avoid humidity, dust and cigarette smoke.
When the projector is subjected to these environments,the lens and part of ventilation holes must be cleaned
more often than usual. As long as the projector is properly maintained in this manner, use in these
environments will not reduce the overall operation life. Please note that all internal cleaning must be
performed by an Marantz Authorized Dealer, or Service Center.
• Do not expose the projector to extreme heat or cold.
Operating temperature:41 °F to 95 °F (+5 °C to 35 °C)
Storage temperature:–4 °F to 140 °F (–20 °C to +60 °C)
Concerning the Lamp Replacement
There is potential glass particle hazard if the lamp ruptures.
Caution
Concerning the Setup of the Projector
Concerning the Lamp Unit
There is a potential hazard of glass particle if the lamp ruptures.
In case of lamp rupture,contact your nearest Marantz Authorized Dealer or Service Center for a
replacement.
See “Replacing Lamp Unit”. (
P.31)
95˚F
(+35˚C)
☞
41˚F
(+5˚C)
WARNING
THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
CAUTION : HIGH PRESSURE LAMP CAUTION HOT : UNPLUG
MAY EXPLODED IF IMPROPERLY HANDLED. THE POWER CORD AND WAIT
REFER SERVICING TO QUALIFIED SERVICE 60 MINUTES BEFORE CHARGING
PERSONNEL.
THE LAMP.
ATTENTION :
LA LAMPE SOUS
HAUTE PRESSION PEUT SI ELLE, N'EST
PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN
PERSONNEL D'ENTRETIEN QUALIFIE.
For USA
WARNING
THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
For Europe
CAUTION HOT
UNPLUG THE POWER CORD AND
WAIT 60 MINUTES BEFORE
CHANGING THE LAMP.
Notes on Operation
MODEL NO. VP-16S1 / U1M
AC 120V
60HZ
2.0A
SERIAL NO.
For USA
CAUTION : HIGH PRESSURE LAMP
CAUTION HOT : UNPLUG
MAY EXPLODED IF IMPROPERLY HANDLED. THE POWER CORD AND WAIT
REFER SERVICING TO QUALIFIED SERVICE 60 MINUTES BEFORE CHARGING
PERSONNEL.
THE LAMP.
ATTENTION :
LA LAMPE SOUS
HAUTE PRESSION PEUT SI ELLE, N'EST
PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN
PERSONNEL D'ENTRETIEN QUALIFIE.
ATTENTION CHAUD :
DEBRANCER LE CORD ON
D'ALOMENTION ET ATENDER
60 MINUTES AVANT DE
CHANGER LAMPE.
• The exhaust ventilative hole, the lamp cage cover and adjacent areas may get extremely hot during
projector operation. To prevent injury,do not touch these areas until they have sufficiently cooled
down.
• Allow at least 1 foot (30 cm)of space between the exhaust ventilative hole and the nearest wall or
obstruction.
MODEL NO.• VP-12S1
/ N1S
If the cooling
fan becomes obstructed, a protection device will automatically turn off the projector lamp.
AC 120V 60H
2.0W
This Zdoes
not indicate a malfunction. Remove the projector power cord from the wall outlet and wait at
least 10 minutes.
SERIAL NO.
Then turn on the power by plugging the power cord back in. This will return the projector to the normal
operating condition.
For Europe
ATTENTION CHAUD
CAUTION
DEBRANCER LE CORD ON
D'ALIMENTION ET ATENDER 60
MINUTES AVANT DE CHANGER
LAMPE.
HIGH PRESSURE LAMP MAY EXPLODED IF BEI FALSCHER HANDHABUNG M
IMPROPERLY HANDLED. REFER SERVICING KANN DIE HOCHDRUCKLAMPE
EXPLODIEREN UBERLASSEN
TO QUALIFIED SERVICE PERSONNEL.
SIE WARTUNGSARBEITEN
ATTENTION
NUR FACHPERSONAL.
LA LAMPE SOUS HAUTE PRESSION PEUT
EXPLOSER SI ELLE, N'EST PAS MANIPULEE
CORRECTEMENT, CONFIER L'OPERATION
A UN PERSONNEL D'ENTRETIEN QUALIFIE.
WARNUNG HEISS
ZIEHEN SIE DEN NETZSTECKER
AB UND WARTEN SIE 60 MINUTEN,
BEVOR SIE DIE GLUHLAMPE
WECHSELN.
2
ATTENTION CHAUD :
DEBRANCER LE CORD ON
D'ALOMENTION ET ATENDER
60 MINUTES AVANT DE
CHANGER LAMPE.
VORSICHT :
MADE IN JAPAN
FABRIQUE AU JAPON
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Incorporates the latest DLP® chip -- “1080p DLP®” (1920 x 1080 pixel, 16:9 wide panel). Using an
optimized system for movie viewing with specially designed image circuits and optical parts, the VP15S1 bring high color reproduction with the pitch black of movie films that reproduces images in rich
tones and crisp black.
Images are sharply detailed, smooth and high quality owing to a powerful chip that builds into a
dedicated processor an image processing IC featuring Gennum’s proud “VXP TM” high quality
contouring technology, “TruMotionHDTM”, “FineEdgeTM”, “RealityExpansionTM” and “FidelityEngineTM”.
Konica Minolta optical system custom-made for Marantz.
A large 98mm 6-segment color wheel.
4 Picture Modes (Theater, Standard, Dynamic, User)
5 built-in preset gammas
Fine-adjustment menus that allow the user to adjust images as they like
18 user menus for saving adjusted images
Color temperature setting (5250K, 5800K, 6500K, 7500K, 9300K)
Black level adjustment
Supports input of NTSC, PAL, SECAM and satellite broadcasts (480i/p, 540p, 576i/p, 720p, 1035i,
1080i/p).
Rich array of input jacks including HDCP supporting HDMI digital input jack and dual system
component jacks
1.45x zoom lens
Lens shift feature for vertically positioning the projection point
Digital correction of vertical keystone distortion
Projection modes for functional, hanging and rear projection
Remote controller with all back-lit keys
Equipped with RS-232C port and 12V trigger terminal for custom installation
Marantz system bus port
Low operating noise thanks to a die-cast silent duct, hermetically sealed color wheel motor and fan speed
control
Highly rigid die-cast chassis to minimize radiating noise
2000 hr long-life 200W SHP lamp with double-shielded safety structure
ACCESSORIES
• Lens Cap x 1
ENGLISH
FEATURES
• AC Power Code
For USA
00MZC01802110
• Remote Controller x 1
For Europe
00MZC02003190
STANDBY
ON
IRIS
LAMP
C.TEMP
GAMMA
COMP.1
COMP.2
S-VIDEO
USER
C1
C2
S
HDMI 1
HDMI 2
VIDEO
H1
H2
V
AUX 1
AUX 2
G1
G2
A1
A2
RGB
G3
THTR
STD
DYN
G4
B1
B2
• User Guide x 1
BLANKING
V-MUTE
B3
OFF
MENU
M
INPUT
ENTER
A
I
ASPECT
CINEMA
INFO.
VCR MODE
BLACK LEVEL
PATTERN
BLACK
FULL
NOR
ZOOM
REMOTE CONTROLLER
RC-11VPS1
THRU
• Warranty Card
(1 copy each for USA, CANADA)
Comes with USA model only.
• AAA Size Batteries x 2
– Digital Light Processing, DLP, DLP logo and DLP Medallion logo are registered trademarks of Texas
Instruments.
– VXP, Visual Excellence Processing and the VXP Logo are trademarks or registered trademarks of
Gennum Corporation.
– All trademarked product names mentioned in this manual are the property of their respective
companies.
– HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.
3
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ4
ENGLISH
PROJECTOR LAYOUT AND FUNCTIONAL OVERVIEW
!0 ON indicator
Front and Top View
Lights up blue when power is ON. When power is
shut OFF, the lamp flashes for about 1 minute
before going out.
!3
!1 STANDBY indicator
Lights up green when the projector is on standby.
!2 WARNING/LAMP indicator
Flashes or lights up when something is wrong with
the lamp cover, lamp, fan, or temperature inside
the projector.
For more information on the error mode, see the
“Error Mode List” (
P.35)
☞
!3 Ventilation holes (intake)
!4 Ventilation holes (exhaust)
Notes:
• Do not place anything near the ventilation
holes to avoid overheat inside the unit.
• Do not place your hand or objects near the
ventilation holes; the air is coming out.
Projection
Lens
!4
IR sensor
q Focus ring (☞ P.11)
y ENTER button
Adjust the picture focus.
Press to enter the selected menu item.
w Zoom ring (☞ P.11)
u INPUT SELECT button (☞ P.18)
Adjust the size of the projected image.
e Lens Shift knob (☞ P.12)
Manually adjust the position of the image vertically.
r
/ I button (☞ P.18)
Press to turn the projector ON or STANDBY mode.
t MENU button (☞ P.21)
Display the on-screen menu.
4
Selects the input signal (COMPONENT 1,
COMPONENT 2, S-VIDEO, VIDEO, RGB, HDMI 1
and HDMI 2).
i PATTERN button (☞ P.11)
Projects a focus pattern on the screen.
o The 3 / 4 / 1 / 2 buttons
Control the MENU cursor.
Note: Pixel defects
DLP ® chip is one of the most advanced
technologies for consumer products. The
DLP® chip made by high precision technology,
however some pixel defects may be found on
the projected image. We are trying our best to
control the quality in order to reduce the
number of defective pixels. It is almost
impossible to have zero pixel defects, even
using the most advanced technology. This is
not a problem only for Marantz, but all DLP®
projector manufactures. Therefore we have to
note that the warranty does not cover the
DLP® chip for pixel defects. We appreciate
your understandings.
Note: Lamp
SHP lamp is one of the most advanced
technologies for consumer products. The
lamp made by high precision technology,
however some lamps might be failing before it
reaches its life. And projector’s brightness is
getting darker along with accumulated lamp
usage hours. We are trying our best to control
the quality in order to reduce lamp failures. It
is almost impossible to have zero failure, even
using the most advanced technology. This is
not a problem only for Marantz, but all
projector manufactures. Therefore we have to
note that the warranty does not cover the SHP
lamp for lamp failures: explosion, and nonlighting except initial use. And also we have to
note that the warranty does not cover the SHP
lamp for lamp failures: flickering, and getting
darker along with accumulated lamp usage
hours. We appreciate your understandings.
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ5
IR sensor
Bottom View
ENGLISH
Rear and Terminals View
Ventilation holes (intake)
Ventilation holes (intake)
x
Ventilation holes
(exhaust)
z
Lamp cover
Adjustable
feet
Lamp cover
securing screw
z
x
z AC IN (☞ P.9)
Connect the supplied AC power code.
x RGB IN
Connect the analog RGB output from an IBM VGA
or compatible equipment.
c COMPONENT VIDEO IN 1 and 2
Terminals 1 and 2 have each Y, P B/C B, P R/C R
terminals. Connect them to the component video
output of a video device, AV amp/processor, DVD
player, etc.
v S-VIDEO IN
Connect the S-VIDEO output from a video
equipment.
b VIDEO IN
Connect the composite video output from a video
equipment.
n TRIG.1(TRIGGER 1)
, TRIG.2(TRIGGER 2)
When the unit is turned on, 12V is output. When the
unit is turned off, no voltage is output. This allows
such as a powered up/down screen,whenever the
projector is turned on or off.
Select ON or OFF at each aspect mode, such as
Full, Normal, Zoom, V-Stretch and Through to
control screen aspect ratio with powered up/down
dual aspect ratio screen.
Note:
• Do not use TRIG.1, as the power source.
• To connect with external devices, use an
ordinal 3.5mm mini-plug (mono) cable.
Notes:
• Do not use TRIG.2, as the power source.
• To connect with external devices, use an
ordinal 3.5mm mini-plug (mono) cable.
m REMOTE IN/OUT
By connecting this projector to another Marantz
audio component using a supplied System Control
cable, you can remotely operate the components
as a single system.
• When connecting to component with a remote
sensor (such as the SR9500,SR8500), be sure
to connect the "REMOTE CONTROL IN" jack
of this projector to the "REMOTE CONTROL
OUT" jack of the component with the remote
sensor.
Note:
For connections, use the control adaptor cable.
(Mini jack to RCA)
Adjustable feet
z Adjustment lever (☞ P.12)
Lift the projector and turn the adjustment lever right
or left. The adjustable feet will extend from the
projector. Then, release the lever, the adjustable
feet is locked.
x Screw holes for ceiling mount kit
. HDMI IN 1 and 2
Connect the digital signal (TMDS compliant, single
link only)
Note:
To use the HDMI terminal, please follow the
cautions on page 10.
⁄0 RS-232C
This is the control port for the custom installer.
5
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ6
¡5 THEATER (THTR) button (☞ P.24)
Remote Controller
ENGLISH
a
s d f g
h j k
a STANDBY button (☞ P.20)
STANDBY
ON
LAMP
C.TEMP
GAMMA
COMP.1
COMP.2
S-VIDEO
USER
G1
£0
£1
C1
C2
S
HDMI 2
VIDEO
H1
H2
V
G2
AUX 1
AUX 2
¡2 ¡3 ¡4
A1
A2
RGB
G3
¡5 ¡6 ¡7
THTR
STD
DYN
G4
BLANKING
¡8 ¡9 ™0 ™1
™2
™3
™4
™5
™6
™7 ™8
™9
IRIS
HDMI 1
l ¡0 ¡1
Turn the projector off.
B1
B2
V-MUTE
B3
OFF
MENU
M
A
I
ASPECT
INFO.
VCR MODE
BLACK LEVEL
PATTERN
BLACK
FULL
NOR
Switches lens and illumination aperture.
£2
£3
£4
£5
£6
£7
d LAMP button
Switches the lamp between the normal and
energy-saving modes.
f C.TEMP button
Sets color temperature to 1, 2, 3, 4, 5 or HB.
g GAMMA button
Sets the gamma curve to Theater, Standard,
Dynamic, A, B, C, D or E, when the picture mode is
set to User.
INPUT
ENTER
CINEMA
s IRIS button
ZOOM
THRU
£8
£9
¢0
¢1
h COMP. 1 (Component video in 1)
button (☞ P.18)
Select the STANDARD picture mode.
Standard mode is good for normal pictures.
Every time the button is pressed, the selection
rotates in the order of Standard 1 ➔ Standard 2 ➔
Standard 3 ➔ Default.
¡7 DYNAMIC (DYN) button (☞ P.24)
Select the Dynamic picture mode.
Dynamic mode is good for visually dynamic
pictures.
Every time the button is pressed, the selection
rotates in the order of Dynamic 1 ➔ Dynamic 2 ➔
Dynamic 3 ➔ Default.
¡8 B1 button (☞ P.29)
Selects Blanking Memory 1.
j COMP. 2 (Component video in 2)
button (☞ P.18)
Selects Blanking Memory 2.
¡9 B2 button (☞ P.29)
™0 B3 button (☞ P.29)
Selects Blanking Memory 3.
k S-VIDEO button (☞ P.18)
™1 OFF button (☞ P.29)
l HDMI 1 button (☞ P.18)
™2 V-MUTE button
¡0 HDMI 2 button (☞ P.18)
™3 3 / 4 / 1 / 2 / ENTER buttons
Select the S-VIDEO IN signal.
Select the HDMI 1 IN signal.
Select the HDMI 2 IN signal.
¡1 VIDEO button (☞ P.18)
Select the VIDEO IN signal.
¡2 A1 button
This button does not work with this projector.
¡3 A2 button
This button does not work with this projector.
¡4 RGB button (☞ P.18)
Select the RGB IN signal.
6
¡6 STANDARD (STD) button (☞ P.24)
Selects the device connected to the COMPONENT
VIDEO IN 1 jack as the input source.
Selects the device connected to the COMPONENT
VIDEO IN 2 jack as the input source.
REMOTE CONTROLLER
RC-11VPS1
Select the Theater picture mode.
Theater mode is designed for high fidelity black
appearance and is good for movie pictures.
Every time THTR button is pressed, the selection
rotates in the order of Theater 1 ➔ Theater 2 ➔
Theater 3 ➔ Default.
Turns the blanking mode off.
Turn the picture into black. Press again to resume.
™6 CINEMA button (☞ P.26)
Turns the 2-3 pull down mode on and off.
™7 FULL button (☞ P.18)
Sets aspect ratio to full mode.
™8 NORMAL button (☞ P.18)
Sets aspect ratio to normal mode.
™9 ON button (☞ P.18)
Turn the projector on.
£0 USER G1 button (☞ P.24)
Selects the user mode.
The user mode is for enjoying images at a userselected gamma curve.
Every time the button is pressed, the selection
rotates in the order of User 1 ➔ User 2 ➔ User 3.
For more information on how to select gamma
curve. (
P.25)
☞
£1 USER G2 button (☞ P.24)
Selects the user mode.
The user mode is for enjoying images at a userselected gamma curve.
Every time the button is pressed, the selection
rotates in the order of User 4 ➔ User 5 ➔ User 6.
For more information on how to select gamma
curve. (
P.25)
☞
£2 USER G3 button (☞ P.24)
Selects the user mode.
The user mode is for enjoying images at a userselected gamma curve.
Every time the button is pressed, the selection
rotates in the order of User 7 ➔ User 8 ➔ User 9.
For more information on how to select gamma
curve. (
P.25)
☞
Press the cursor buttons (3 [UP], 4 [DOWN], 1
[LEFT], 2 [RIGHT]) to select menu items. Press
the ENTER button to enter the selected menu item.
£3 USER G4 button
™4 ASPECT (Aspect select) button
(☞ P.18)
Lights all buttons for about 10 sec.
Selects the aspect ratio. Every time the button is
pressed, the selection rotates in the order of Full ➔
Normal ➔ Zoom ➔ V-Stretch ➔ Through.
™5 VCR MODE button (☞ P.26)
Turns the VCR mode on and off.
This button does not work with this projector.
£4 LIGHT button
£5 MENU button (☞ P.21)
Display the on-screen menu.
If pressed again, the on-screen menu disappears.
£6 INFO. button (☞ P.31)
Turn the information menu on or off.
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ7
£7 INPUT (Input signal select)
button (☞ P.18)
ENGLISH
Selects the input signal. Every time the 3/4
buttons are pressed, the input signal rotates in the
order of COMPONENT 1 ↔ COMPONENT 2 ↔ SVIDEO ↔ VIDEO ↔ RGB ↔ HDMI 1 ↔ HDMI 2.
£8 BLACK LEVEL button (☞ P.26)
Sets the black level.
During analog signal input ......0 IRE/7.5 IRE
During HDMI signal input ........Expand/Normal
£9 PATTERN button (☞ P.11)
Projects a focus pattern on the screen.
¢0 ZOOM button (☞ P.18)
Sets aspect ratio to zoom mode.
¢1 THROUGH button (☞ P.18)
Sets aspect ratio to through mode.
7
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ8
Preparing the Remote Controller
Remote Controller Operational Range
1. Take the cover off the battery case on the
remote control backside.
Battery case cover
Remote
Controller
5m
ENGLISH
Operate the remote controller within a distance of approximately 5m from the IR sensor (remote sensor)
on the projector.
Remote control operation may not be possible if the remote control unit’s transmitter is not pointing in the
direction of the remote sensor or if there is an obstruction between the transmitter and the remote sensor.
Remote
Controller
2. Insert two AAA size batteries.
Make sure the polarities match the + and –
marks inside the battery compartment.
120
5m
60
AAA size batteries
VP-15S1
Remote
Controller
Remote
Controller
60
5m
5m
60
VP-15S1
3. Reattach the battery case cover as before.
Remote
Controller
5m
60
VP-15S1
8
Battery case cover
Notes :
• Do not mix alkaline and manganese batteries.
• Do not mix old and new batteries.
CAUTIONS ON BATTERIES
• Use AAA alkaline batteries in this remote
controller.
• If the remote control unit does not operate
from close to the main unit, replace the
batteries with new ones, even if less then a
year has passed.
• The included battery is only for verifying
operation. Replace it with a new battery as
soon as possible.
• When inserting the batteries, be careful to
do so in the proper direction, following the +
and - marks in the remote control unit’s
battery compartment.
• To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• Remove the batteries when not planning to
use the remote control unit for a long period
of time.
• If the batteries should leak, carefully wipe off
the fluid from the inside of the battery
compartment, then insert new batteries.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules that
apply in your country or area.
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ9
❖ When making connections be sure to:
• Turn off all equipment before making any connections.
• Use the proper cables for each connection.
• Securely insert the plug into the port to connect cables. Loose cables can lead to trouble and damage.
❖ When pulling out a cable:
• Be sure to grab the plug, not the cable itself.
Connection with Video Equipments
You can connect this projector to a VCR, DVD player and other video equipment.
Connecting a video source using S-VIDEO IN and VIDEO IN terminals.
1.
Connect one of the S-video cable to the S-VIDEO IN terminal, or one end of the video cable to the VIDEO
IN terminal on the projector.
2.
Connect the other end of the S-video cable or the video cable to the S-video output terminal or video
output terminal of the video source.
Connecting a DVD player to the COMPONENT VIDEO IN 1 or 2 terminal
(Devices can be connected to both terminals at the same time.)
1.
Connect the individual terminals of the component video cable into the COMPONENT VIDEO IN 1 or 2
terminal of the projector.
2.
Connect the other end of the cable to the corresponding terminals on a DVD player.
Connection with AC Power Supply
Connect the supplied AC power cord into the AC IN socket of the projector.
The STANDBY indicator lights up and the projector goes into the standby mode.
Note : Make sure the AC power cord is firmly connected into the AC IN socket.
Component cable
(commercially available)
COMPONENT VIDEO OUT
STANDBY
FL OFF
DVD Player
Component cable
(commercially available)
COMPONENT VIDEO OUT
STANDBY
FL OFF
DVD Player
S-video cable (commercially available)
SUOMI
S-VIDEO OUT
VARO
Laite on liitettava suojamaadoitus-koskettimilla varustettuun pistorasiaan.
VIDEO OUT
KONGERIKET NORGE
Video cable
(commercially available)
VCR
FORSIKTIG
Apparatet ma tilkoples jordet stikkontakt.
SVENSKA
OBSERVERA
Apparaten skall anslutas till jordat uttag.
9
ENGLISH
CONNECTION
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ10
Connection with a HD-Video, DVD Player, Satellite, Cable Tuner or PC
ENGLISH
You can connect this projector to HD-Video /PC using RGB IN port, or DVD Plyer /Satellite /Cable Tuner
/PC using HDMI IN port.
1. Connect one end of the RGB cable to the RGB IN port, or one end of the HDMI cable to the HDMI IN
port on the projector.
2. Connect the other end to the corresponding port on a HD-Video, Satellite, Cable Tuner or personal
computer.
3. If using DVI-A or DVI-D output, use respectively a DVI-A-RGB or DVI-D-HDMI conversion cable.
Note : When projecting a video image from a device connected to the HDMI terminal, follow the
procedure below.
1. Turn on power of this unit. (
P.18)
2. Set the input video source to HDMI input. (
P.18)
3. Turn on power of the device connected to the HDMI terminal of the unit (i.e. DVD player).
If the procedure above is not followed, projected image may corrupt.
For the details of the HDMI terminal on the device connected with the unit, see the instruction
manual of the device.
☞
☞
Advanced Connection
You can control total home theater system using PC or Marantz receiver equipment.
For installing below system, consult with Marantz authorized dealer.
Screen
RS-232C cable
(female-female, straight type,
commercially available)
RS-232C
External Controller
3.5mm Mini Plug (Mono)
(commercially available)
RGB (D-Sub monitor) cable
(commercially available)
RGB OUT
OUT
RGB
or
or out
DVI-D
DVI-A OUT
DVI-D OUT
or
HDMI OUT
Control Adapter cable
(commercially available)
HD-Video / Satellite /
Cable Tuner / DVD Player
Monitor output
RGB OUT
RGB
out
or
or
DVI-D out
DVI-D out
HDMI-HDMI cable or HDMI-DVD-D cable
(commercially available)
10
IBM VGA or
Compatible PC
REMOTE CONTROL IN
REMOTE CONTROL OUT
Control Adapter cable
(commercially available)
Receiver equipment
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ11
ENGLISH
Detail Focusing
INITIAL SETTING
You can strictly focus the image with focus pattern.
1. Press the PATTERN button to project the focus pattern on the screen.
Turning on the Power
V-MUTE
MENU
M
1.
2.
☞
Connect the supplied AC power cord. (
P.9)
Press the ON button on the remote controller or the
INPUT
ENTER
/ I button on the projector.
A
I
INFO.
ASPECT
The ON indicator lights up.
CINEMA
VCR MODE
BLACK LEVEL
PATTERN
BLACK
FULL
STANDBY
NOR
ZOOM
THRU
ON
IRIS
LAMP
C.TEMP
GAMMA
COMP.1
COMP.2
S-VIDEO
USER
C1
C2
S
G1
HDMI 1
HDMI 2
VIDEO
H1
H2
V
G2
AUX 1
AUX 2
A1
A2
RGB
G3
THTR
STD
DYN
G4
2.
Turn the Focus ring to make an adjustment.
Adjust the focus for the sharpest image possible to obtain, using focus pattern.
Zooming and Focusing
Project an image on the screen roughly at first.
1. Turn the Zoom ring and adjust to the desired size
within the zoom range.
WIDE: Enlarges (zooms in) the projected image.
3.
TELE: Reduces (zooms out) the projected image.
2.
Turn the Focus ring until the image on the screen
becomes clear.
Press the PATTERN button again to hide the focus pattern. This completes fine focusing.
Note :
WIDE
1.
2.
☞
Focus Pattern Color by Lens Shift Position (
P.16)
The focus pattern changes color depending on the lens position. There are two colors and they can
be used for checking the quality of the projected image. The white focus pattern uses the highest
optical performance to maximize the sharpness of the projected image. To enjoy the highest
sharpness, it is recommended to position the lens within this range.
When the lens is shifted outside the aforementioned range, the focus pattern turns green. Rough
focusing in this range looses image sharpness.
Adjusting the zoom position from WIDE to TELE enhances sharpness even at the same lens
position.
TELE
11
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ12
Adjusting the Image Position
Adjusting the Height
ENGLISH
You can adjust the image position with the Lens Shift knob.
❖ Turn the Lens Shift knob to clockwise : The image goes up.
Clockwise
You can position the projected image by changing the
height of the projector’s adjusters.
1. Move the adjuster lever to the left or right to
enable adjuster changing. Carefully lift the
projector.
2.
Once having positioned the projector, return the
adjuster lever as before to lock in place. Check
the adjusters are securely locked before
releasing your hands from the projector.
3.
Turn the adjuster to fine-adjust the height.
Up
❖ Returning the Projector to its Initial Position
Slightly lift the projector, turn the adjuster lever to the left or right, then carefully set the projector down.
❖ Turn the Lens Shift knob to counterclockwise : The image goes down.
Counterclockwise
Keystone Correction
When the projecting image is a trapezoid, correct it in Keystone and in the Display Menu.
P.28)
See “Display”. (
When using the keystone feature to correct a trapezoidal image, picture contours can look like staircases
because of image correction.
☞
❖ Keystone
(Electronic keystone correction)
Down
12
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ13
ENGLISH
INSTALLATION
Recommended Setting
❖ Mounting on the ceiling
❖ Installing on a tabletop
Screen
Screen
Screen upper end
Screen upper end
Lens shift range
Lens shift range
Range from light axis to upper
end
Height from installing
level to light axis
Screen size (vertical)
Screen size (vertical)
Range from light axis to upper end
Light axis (center)
Light axis (center)
Installing level
Screen lower end
Height from installing level to light axis
Screen lower end
Projection distance
Projection distance
lens head
lens head
CAUTION
– For ceiling installation, consult with Marantz authorized dealer.
– Do not look into the lens when the projector is turned on. It could damage your eyesight.
13
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ14
Screen Size and Projection Distance (inch) VP-15S1
Screen
Screen size
(Diagonal)
Screen
ENGLISH
Screen size
(Diagonal)
Screen Size and Projection Distance (mm) VP-15S1
VP-12S1
VP-12S1
Projection distance
Height
Width
: Image size = Screen size
❖ 4 : 3 Screen
Height
Width
: Image size
: Screen size
14
Width
Height
Minimum
Maximum
inch
inch
inch
inch
inch
88 6/16
34 5/16
61
129 1/16
70
90 15/16
35 5/16
62 12/16
132 13/16
72
101 5/16
39 4/16
69 12/16
147 13/16
80
103 14/16
40 3/16
71 8/16
151 9/16
82
106
7/16
41
3/16
73
3/16
155 5/16
84
114 3/16
44 2/16
78 7/16
166 8/16
90
116 13/16
45 2/16
80 3/16
170 4/16
92
127 2/16
49
87 3/16
185 4/16
100
134 14/16
51 15/16
92 6/16
196 7/16
106
140 1/16
53 15/16
95 14/16
203 15/16
110
153
58 13/16
104 9/16
222 11/16
120
156 14/16
60 5/16
107 3/16
228 4/16
123
169 12/16
65 3/16
115 15/16
247
133
172
6/16
66
3/16
117
11/16
250 12/16
135
191 12/16
73 9/16
130 12/16
278 13/16
150
217 9/16
83 6/16
148 3/16
316 4/16
170
256 6/16
98 1/16
174 5/16
372 6/16
200
321
122 9/16
217 14/16
465 15/16
250
To calculate the installation measurement (unit : inch)
Minimum = 1 5/16 x Screen Size - 2 2/16
Maximum= 1 14/16 x Screen Size - 1 15/16
Note : When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.
4:3 Screen Size (1.33:1 Aspect Ratio)
In case of displaying the 16:9
picture on the whole of the 4:3
screen.
Projection Distance
Diagonal
Projection Distance
Diagonal
Width
Height
Minimum
Maximum
inch
inch
inch
inch
inch
70
158 5/16
108 8/16
42
56
162 14/16
72
111 10/16
43 3/16
57 10/16
181 3/16
124 5/16
48
64
80
185 13/16
127 7/16
49 3/16
65 10/16
82
190 6/16
130 10/16
50 6/16
67 3/16
84
204 2/16
140 1/16
54
72
90
208 11/16
143 4/16
73 10/16
55 3/16
92
227
155 14/16
80
60
100
240 12/16
165 6/16
84 13/16
63 10/16
106
249 14/16
66
171 11/16
88
110
272 12/16
187 8/16
96
72
120
279 10/16
73 13/16
192 4/16
98 6/16
123
302 9/16
79 13/16
208
106 6/16
133
307 2/16
81
211 3/16
108
135
341 7/16
90
234 14/16
120
150
387 4/16
102
266
8/16
136
170
455 14/16
313 14/16
120
160
200
570 6/16
150
392 14/16
200
250
To calculate the installation measurement (unit : inch)
Minimum = 1 9/16 x Screen Size - 2 2/16
Maximum= 2 5/16 x Screen Size - 1 15/16
Note : When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.
❖ 16 : 9 Screen
16:9 Screen Size (1.77:1 Aspect Ratio)
In case of displaying the 16:9
picture on the whole of the
16:9 screen.
Width
Height
16:9 Screen Size (1.77:1 Aspect Ratio)
In case of displaying the 16:9
picture on the whole of the
16:9 screen.
: Image size = Screen size
Projection Distance
Diagonal
Width
Height
Minimum
inch
mm
mm
mm
Maximum
mm
70
72
80
82
84
90
92
100
106
110
120
123
133
135
150
170
200
250
1550
1594
1771
1815
1860
1992
2037
2214
2347
2435
2657
2723
2944
2989
3321
3763
4428
5535
872
897
996
1021
1046
1121
1146
1245
1320
1370
1494
1532
1656
1681
1868
2117
2491
3113
2243
2308
2571
2636
2702
2899
2964
3227
3423
3555
3883
3981
4309
4375
4867
5523
6507
8147
3276
3371
3751
3846
3941
4226
4321
4701
4986
5176
5651
5794
6269
6364
7076
8026
9451
11826
To calculate the installation measurement (unit : mm)
Minimum = 32.8 x Screen Size - 53.4
Maximum= 47.5 x Screen Size - 48.8
Note : When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.
❖ 4 : 3 Screen
4:3 Screen Size (1.33:1 Aspect Ratio)
In case of displaying the 16:9
picture on the whole of the 4:3
screen.
Width
Height
❖ 16 : 9 Screen
Projection distance
: Image size
: Screen size
Projection Distance
Diagonal
Width
Height
Minimum
Maximum
inch
mm
mm
mm
mm
4018
1422
1067
2754
70
4134
1463
1097
2834
72
4599
1626
1219
3155
80
4715
1666
1250
3235
82
4832
1707
1280
3315
84
5180
1829
1372
3556
90
5296
1869
1402
3636
92
5761
2032
1524
3957
100
6110
2154
1615
4197
106
6342
2235
1676
4358
110
6923
2438
1829
4759
120
7098
2499
1875
4879
123
7679
2703
2027
5280
133
7795
2743
2057
5360
135
8666
3048
2286
5962
150
9828
3454
2591
6764
170
11571
4064
3048
7967
200
14476
5080
3810
9972
250
To calculate the installation measurement (unit : mm)
Minimum = 40.1 x Screen Size - 53.4
Maximum= 58.1 x Screen Size - 48.8
Note : When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ15
Screen Size and Projection Distance (inch) VP-15S1L
ENGLISH
Screen
Screen size
(Diagonal)
Screen
Screen size
(Diagonal)
Screen Size and Projection Distance (mm) VP-15S1L
VP-12S1
VP-12S1
Projection distance
In case of displaying the 16:9
picture on the whole of the
16:9 screen.
Height
Width
: Image size = Screen size
❖ 4 : 3 Screen
Height
Width
: Screen size
Height
Minimum
Maximum
inch
inch
inch
inch
inch
29 7/16
52 5/16
60
34 5/16
61
70
35 5/16
62 12/16
72
147 3/16
39 4/16
69 12/16
222 3/16
80
150 15/16
40 3/16
71 8/16
227 13/16
82
154 10/16
41 3/16
73 3/16
233 7/16
84
165 14/16
44 2/16
78 7/16
250 5/16
90
169 10/16
45 2/16
80 3/16
255 15/16
92
184 10/16
49
87 3/16
278 6/16
100
195 13/16
51 15/16
92 6/16
295 4/16
106
203 5/16
53 15/16
95 14/16
306 8/16
110
222
58 13/16
104 9/16
334 9/16
120
227 10/16
60 5/16
107 3/16
343
123
246 6/16
65 3/16
115 15/16
371 1/16
133
250 2/16
66 3/16
117 11/16
376 11/16
135
278 3/16
73 9/16
130 12/16
418 14/16
150
315 10/16
83 6/16
148 3/16
475
170
371 12/16
98 1/16
174 5/16
559 5/16
200
465
5/16
122
9/16
217
14/16
699
12/16
250
558 14/16
147 1/16
261 8/16
840 4/16
300
To calculate the installation measurement (unit : inch)
Minimum = 2 13/16 x Screen Size - 2 9/16
Maximum= 1 14/16 x Screen Size - 2 9/16
Note : When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.
4:3 Screen Size (1.33:1 Aspect Ratio)
In case of displaying the 16:9
picture on the whole of the 4:3
screen.
: Image size
Projection Distance
Width
Projection Distance
Diagonal
Width
Height
Minimum
Maximum
inch
inch
inch
inch
inch
60
203 13/16
36
48
238 4/16
70
157 11/16
42
56
245 2/16
162 4/16
43 3/16
57 10/16
72
272 10/16
180 9/16
64
48
80
279 8/16
185 3/16
49 3/16
65 10/16
82
286 6/16
189 12/16
50 6/16
67 3/16
84
307
54
203 8/16
72
90
313 15/16
55 3/16
208 1/16
73 10/16
92
341 7/16
226 6/16
80
60
100
362 1/16
240 2/16
84 13/16
63 10/16
106
375 13/16
249 4/16
88
66
110
410 3/16
72
272 2/16
96
120
420 9/16
73 13/16
279
98 6/16
123
454 15/16
79 13/16
301 14/16
106 6/16
133
461 13/16
306 8/16
108
81
135
513 6/16
340 13/16
120
90
150
582 3/16
386 10/16
136
102
170
685 6/16
160
120
455 4/16
200
857 6/16
150
569 12/16
200
250
1029
6/16
180
684 3/16
240
300
To calculate the installation measurement (unit : inch)
Minimum = 3 7/16 x Screen Size - 2 9/16
Maximum= 2 5/16 x Screen Size - 2 9/16
Note : When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.
❖ 16 : 9 Screen
16:9 Screen Size (1.77:1 Aspect Ratio)
In case of displaying the 16:9
picture on the whole of the
16:9 screen.
Width
Height
16:9 Screen Size (1.77:1 Aspect Ratio)
Diagonal
: Image size = Screen size
❖ 4 : 3 Screen
Width
: Image size
: Screen size
Projection Distance
Diagonal
Width
Height
Minimum
Maximum
inch
mm
mm
mm
mm
747
1328
60
872
1550
70
897
1594
72
5640
3735
996
1771
80
5782
3830
1021
1815
82
5925
3925
1046
1860
84
6353
4210
1121
1992
90
6495
4305
1146
2037
92
7066
4685
1245
2214
100
7493
4970
1320
2347
106
7779
5160
1370
2435
110
8492
5635
1494
2657
120
8706
5778
1532
2723
123
9419
6253
1656
2944
133
9561
6348
1681
2989
135
10631
7060
1868
3321
150
12057
8010
2117
3763
170
14196
9435
2491
4428
200
17761
11810
3113
5535
250
21326
14185
3736
6641
300
To calculate the installation measurement (unit : mm)
Minimum = 71.3 x Screen Size - 64.4
Maximum= 47.5 x Screen Size - 64.8
Note : When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.
4:3 Screen Size (1.33:1 Aspect Ratio)
In case of displaying the 16:9
picture on the whole of the 4:3
screen.
Height
❖ 16 : 9 Screen
Projection distance
Projection Distance
Diagonal
Width
Height
Minimum
Maximum
inch
mm
mm
mm
mm
5174
1219
914
60
6047
1422
1067
4002
70
6221
1463
1097
4118
72
6920
1626
1219
4583
80
7094
1666
1250
4699
82
7269
1707
1280
4816
84
7793
1829
1372
5164
90
7967
1869
1402
5280
92
8666
2032
1524
5745
100
9189
2154
1615
6094
106
9539
2235
1676
6326
110
10412
2438
1829
6907
120
10674
2499
1875
7082
123
11547
2703
2027
7663
133
11721
2743
2057
7779
135
13031
3048
2286
8650
150
14777
3454
2591
9812
170
17396
4064
3048
11555
200
21761
5080
3810
14460
250
26126
6096
4572
17365
300
To calculate the installation measurement (unit : mm)
Minimum = 87.3 x Screen Size - 64.4
Maximum= 58.1 x Screen Size - 64.8
Note : When installing the projector, consider ±5% tolerance for the Projection Distance in the above table.
15
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ16
Lens shift position VP-15S1
❖ Extended mounting condition (From +100% to +165%)
Screen Position
+100%
(+100%)
0.5H
Up
VP-15S1
0% (Center)
VP-15S1
0% (Center)
0.3H Up
More
Focus pattern color: Green
+165%
Screen Position
Focus pattern color: White
ENGLISH
❖ Standard condition (From -85% to +100%)
0.4H
Down
-85%
Screen Height = 1H
CAUTION:
In the expanded mounting condition (green focus pattern), the corners of the picture may appear
dark or distorted.
16
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ17
ENGLISH
Lens shift position VP-15S1L
❖ Standard condition (From -85% to +165%)
Screen Positon
+165%
Focus pattern color: White
0.8 H Up
VP-15S1L
0% (Center)
0.4H Down
-85%
Screen Height = 1H
17
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ18
Selecting the Aspect Mode
ENGLISH
BASIC OPERATIONS
You can select 5 kinds of ASPECT mode using remote controller.
Pressing the ASPECT button on the remote control rotates the
aspect ratio in the order of FULL ➔ NORMAL ➔ ZOOM ➔ VSTRETCH ➔ THROUGH, allowing you to select an aspect ratio.
An aspect ratio can also be directly selected by pressing one of
the FULL, NORMAL, ZOOM or THROUGH buttons on the remote
controller. A selection can also be made from the menu. (
P.26)
Turning on the Power
Press the ON button on the remote controller or the
The ON indicator lights up.
/ I button on the projector.
☞
BLANKING
B1
B2
V-MUTE
B3
OFF
MENU
M
INPUT
ENTER
A
I
ASPECT
CINEMA
INFO.
VCR MODE
BLACK LEVEL
PATTERN
BLACK
STANDBY
FULL
ON
IRIS
LAMP
C.TEMP
GAMMA
COMP.1
COMP.2
S-VIDEO
USER
G1
C1
C2
S
HDMI 1
HDMI 2
VIDEO
H1
H2
V
G2
AUX 1
AUX 2
A1
A2
RGB
G3
THTR
STD
DYN
G4
Selecting the Input Signal Source
Switch to the equipment connected to the projector.
Every time the INPUT button of the projector or the INPUT 3 button of the remote controller is pressed,
the input signal rotates in the order of COMPONENT 1 ➔ COMPONENT 2 ➔ S-VIDEO ➔ VIDEO ➔ RGB
➔ HDMI 1 ➔ HDMI 2. When the INPUT 4 button of the remote controller is pressed, the input signal
rotates in the opposite order. An input signal can also be directly selected by pressing one of the COMP.1,
COMP.2, S-VIDEO, VIDEO, RGB, HDMI 1 and HDMI 2 buttons on the remote control.
IRIS
LAMP
C.TEMP
GAMMA
COMP.1
COMP.2
S-VIDEO
USER
C1
C2
S
HDMI 1
HDMI 2
VIDEO
H1
H2
V
AUX 1
AUX 2
G1
G2
A1
A2
RGB
G3
THTR
STD
DYN
G4
B1
B2
BLANKING
V-MUTE
B3
OFF
MENU
M
INPUT
ENTER
18
A
I
ASPECT
INFO.
NOR
ZOOM
THRU
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ19
• Press the ZOOM button, the NORMAL button or the FULL button on the remote controller for the 4:3
aspect ratio video source.
• Press the FULL button on the remote controller for 16:9 aspect ratio video source, such as 1080i,
1035i, and 720p video systems.
• Use Zoom mode when projecting a 480i, 480p, 576i, or 576p squeezed image with a 2.35: 1 aspect
ratio.
• Use V-Stretch mode when projecting a 720p, 1080i, or 1080p squeezed image with a 2.35: 1 aspect
ratio.
❖ Through mode
Images are shown at the same resolution as RGB/video signals.
❖ Original Source Image
16 : 9 video source
The 2.35:1 image is shown across the entire screen. The vertical component of the aspect ratio is
elongated in this case. This function is best used when a 720p, 1080i, or 1080p squeezed image is input.
4 : 3 video source
❖ Full mode
The 16:9 squeezed image is displayed with the
correct aspect.
The 4:3 image is enlarged horizontally.
❖ Normal mode
The picture in normal ratio 4:3 is displayed.
❖ Zoom mode
A 2.35:1 image is displayed in the entire screen.
This function is best used when a 480i, 480p, 576i,
or 576p squeezed image is input.
19
ENGLISH
❖ V-Stretch mode
The Screen Images in a 16:9 screen
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ20
❖ V-Stretch mode
The Screen Images in a 4:3 screen
ENGLISH
• Press the ZOOM button, the NORMAL button or the FULL button on the remote controller for the 4:3
aspect ratio video source.
• Press the FULL button on the remote controller for 16:9 aspect ratio video source, such as 1080i,
1035i, and 720p video systems.
• Use Zoom mode when projecting a 480i, 480p, 576i, or 576p squeezed image with a 2.35: 1 aspect
ratio.
• Use V-Stretch mode when projecting a 720p, 1080i, or 1080p squeezed image with a 2.35: 1 aspect
ratio.
❖ Through mode
❖ Original Source Image
16 : 9 video source
The 2.35:1 image is shown across the entire screen. This function is best used when a 720p, 1080i, or
1080p squeezed image is input.
Images are shown at the same resolution as RGB/video signals.
4 : 3 video source
❖ Full mode
The 16:9 squeezed image is displayed with the
correct aspect.
To Turn off the Power
The 4:3 image is enlarged horizontally.
1.
2.
Press the STANDBY button on the remote controller or the
/ I button on the projector.
The fan continues running for about 1 minute to internally cool the projector. In the meantime, the ON
indicator on the projector flashes a blue color and buttons on the projector and remote control are
irresponsive to touch. Once the fan stops, the ON indicator goes out and the STANDBY indicator
lights up a green color to indicate the projector is on standby.
❖ Normal mode
The picture in normal ratio 4:3 is displayed.
STANDBY
❖ Zoom mode
A 2.35:1 image is displayed in the entire screen.
This function is best used when a 480i, 480p,
576i, or 576p squeezed image is input.
20
ON
IRIS
LAMP
C.TEMP
GAMMA
COMP.1
COMP.2
S-VIDEO
USER
C1
C2
S
G1
HDMI 1
HDMI 2
VIDEO
H1
H2
AUX 1
AUX 2
A1
A2
V
G2
RGB
G3
Notes :
- Do not pull out the AC power cord until the projector turns in standby mode.
- Do not pull out the power cord suddenly in the state of “POWER ON." It can cause a breakdown.
- If the WARNING indicator lights up or blinks a yellow color, check that the fan has stopped then
unplug the AC power cord from its outlet.
- The projector will not be turned on if the ON button on the remote controller or the
/ I button on
the projector is pressed immediately after turning off. Press the ON button on the remote controller
or
/ I button on the projector after the projector turns into standby mode.
- When on standby, power to the projector is not OFF completely. If not planning to use the projector
for an extended period of time, unplug the AC power cord from AC power outlet as explained above.
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ21
Main Menu
Menu Structure
Input Signal
P.27
Main Menu
Picture Mode
P.24
Item
Auto*
720p
480i/576i
1035i
480p
Memory3
P.27
Memory1
1080i
540p
Readjust
1080p
576p
Resolution H
0*
25
Dynamic
Default / 1* / 2 / 3
Resolution V
0*
25
Component 2
1* / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9
Gamma
Theater
Auto*
720p
1035i
480p
B
1080i
540p
Standard
C
Dynamic
D
-50
Brightness
Color
-50
-50
Tint
R10
Sharpness
0*
1080p
S-Video
50
1 / 2 / 3* / 4 / 5 / HB
Lamp Mode
Normal* / Economy
1 / 2 / 3*
R Gain
0*
-50
Video
1080i
540p
1080p
576p
50
B Gain
-50
0*
50
R Bias
-50
0*
50
1035i
480i/576i
G Bias
-50
0*
50
1080i
480p
1080p
576p
50
Luminance Gain
-50
0*
50
-5
0*
5
Chroma Delay
HDMI 1
Aspect
720p
Full*
1035i
480i/576i
1080i
480p
Zoom
1080p
Through
Cinema
Auto* / Off
VCR Mode
Black Level
Auto*
Normal
V-Stretch
Phase
-10
0*
10
Clamp Position
-50
0*
50
Status Info.
Enable* / Disable
Clamp Width
-50
0*
50
Power-OFF Confirm.
Enable / Disable*
CSC HDMI 1
Español
576p
720p
Blanking Memory
Auto*
YCBCR 4:4:4
YCBCR 4:2:2
RGB
YPBPR 4:4:4
YPBPR 4:2:2
CSC HDMI 2
Off* / 1 / 2 / 3
Blanking Top
0*
100
Blanking Bottom
0*
100
Blanking Left
0*
100
Blanking Right
0*
100
Auto*
Deep Color HDMI 1
Auto*
8bit
10bit
12bit
Deep Color HDMI 2
Auto*
HDMI 2
P.26
Français
Auto*
0*
0*
Deutsch
Italiano
RGB
-50
-50
Português
10
YPBPR 4:4:4
G Gain
B Bias
50
YPBPR 4:2:2
50
English*
0*
YCBCR 4:2:2
480p
Center
Language
0*
YCBCR 4:4:4
1035i
Center-L
-10
PAL
480i/576i
Bottom
Bottom-R
-50
SECAM
720p
Top-R
Yes / No*
Auto*
RGB
Top
Bottom-L
Position V
P.28
NTSC
50
0*
HDMI
Top-L*
Center-R
P.29
Position H
SECAM
50
Color Temp.
Noise Reduction
PAL
G10
0*
576p
NTSC
50
0*
Item
Menu Position
Auto*
50
0*
0*
Iris
480i/576i
A
Main Menu
OSD/Blanking
Memory2
Default / 1* / 2 / 3
Contrast
Fine Menu 2
Auto*
Default / 1* / 2 / 3
E
P.26
Item
Mode
Theater
P.25
Fine Menu 1
RGB/HD Adjust
Standard
User
Picture Adjust
Main Menu
Item
Component 1
ENGLISH
OPERATIONS
Auto*
Config.
(Configuration)
P.30
Auto Power OFF
Enable / Disable*
Trigger 2 Full
On* / Off
Trigger 2 Normal
On* / Off
Trigger 2 Zoom
On* / Off
Trigger 2 V-Stretch
On* / Off
Trigger 2 Through
On* / Off
Remote Control
Wireless* / Wired
Reset Lamp Life
Yes / No
Reset All
Yes / No
8bit
10bit
12bit
Display
P.28
Keystone
-25
Scale
-100
Width
-100
Position H
-50
0*
50
Position V
-50
0*
50
Installation
0*
25
0*
0*
F +Front*
Ceiling
R + Ceiling
R +Rear
Ceiling
F + Ceiling
On / Off*
0 IRE* / 7.5 IRE
During HDMI input, “Expand” or “Normal*” is shown.
FRC
Auto 1* / Auto 2 / 60Hz / 50Hz / 48Hz
CEC
Picture Shift V
Overscan
On / Off*
-50
0*
50
Enable* / Disable
* Default setting
21
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ22
Functions by Signal
ENGLISH
NO SIGNAL
VIDEO or S-VIDEO
ANY INPUT
Picture Mode
Picture Adjust
Fine Menu 1
Fine Menu 2
RGB/HD Adjust
22
Theater
Standard
Dynamic
User
Gamma
Contrast
Brightness
Color
Tint
Sharpness
Color Temp.
Lamp Mode
Iris
Noise Reduction
R Gain
G Gain
B Gain
R Bias
G Bias
B Bias
Luminance Gain
Chroma Delay
Aspect
Cinema
VCR Mode
Black Level
FRC
CEC
Picture Shift V
Overscan
Mode
Readjust
Resolution H
Resolution V
Position H
Position V
Phase
Clamp Position
Clamp Width
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
●
●
●
–
–
–
–
–
–
–
–
–
–
–
–
VALID SIGNAL
COMPONENT
1080i/720p/
480p/576p
1080p/540p
NTSC
PAL/SECAM
480i/576i
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
*1
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*1
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*1
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*1
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
–
–
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
–
*4
–
*4
●
–
–
–
–
–
–
–
–
–
RGB
HDMI
480i/576i
480p/576p
Other
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
*1
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
–
–
*1
*9
*9
–
–
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
–
–
*1
*9
*9
–
–
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
–
–
*1
*9
*9
–
–
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
–
–
*1
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
*9
–
–
●
●
●
●
*2
–
●
●
●
–
–
–
–
–
*2
–
●
●
●
●
●
●
●
●
*2
–
*10
–
*4
–
*4
–
*4
–
*4
●
●
●
*3
*4
–
●
●
*3
*4
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
●
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
*5
*6
*6
*5
*5
*5
*5
*5
*5
*6
*6
*5
*5
*5
*5
*5
●
●
●
●
*3
*4
*7
*11
*5 *11
*6 *11
*6 *11
*5 *11
*5 *11
–
–
–
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ23
VIDEO or S-VIDEO
ANY INPUT
HDMI
Display
OSD/Blanking
Configuration
*1
*2
*3
*4
*5
*6
*7
*8
*9
*10
*11
CSC HDMI 1
CSC HDMI 2
Deep Color HDMI 1
Deep Color HDMI 2
Keystone
Scale
Width
Position H
Position V
Installation
Menu Position
Language
Status Info.
Power-OFF Confirm.
Blanking Memory
Blanking Top
Blanking Bottom
Blanking Left
Blanking Right
Auto Power Off
Trigger 2 Full
Trigger 2 Normal
Trigger 2 Zoom
Trigger 2 V-Strech
Trigger 2 Through
Remote Control
Reset Lamp Life
Reset All
VALID SIGNAL
COMPONENT
1080i/720p/
480p/576p
1080p/540p
–
–
–
–
–
–
–
–
NTSC
PAL/SECAM
480i/576i
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
–
–
–
–
●
●
●
●
●
RGB
HDMI
480i/576i
480p/576p
Other
–
–
–
–
–
–
–
–
–
–
–
–
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
*8
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
ENGLISH
NO SIGNAL
Can be selected only when User is selected for the Picture Mode.
On only when interlaced signals are input. (Off for progressive signals.)
On only when 1035i / 1080i signals are input.
On when Aspect is set to V-Stretch for HD signals. For other signals, On when Aspect is set to Zoom or V-Stretch.
On when the RGB/HD Adjust mode is set to Memory.
On when the RGB/HD Adjust mode is set to Memory. However, as an exception, it is Off when Aspect is set to Through or V-Stretch.
On when 480i/p or 576i/p signals are input.
On when Blanking Memory is selected for OSD/Blanking.
Cannot be selected when the default is selected for Picture Mode.
Can be selected when the input signal is 540p, 720p, 1035i, 1080i, or 1080p.
Off when the input signal is 480i/p or 576i/p.
23
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ24
Picture Mode
How to Operate Menus
ENGLISH
This unit has four picture modes: Theater, Standard, Dynamic and User. The picture quality recommended
by Marantz is already set for each mode. The User mode has eight gamma curves that can be chosen and
saved by users. Also, the Theater, Standard and Dynamic modes three indexes for memorizing picture
quality adjustments. Similarly, the User mode has nine, making a total of 18 indexes available for use.
This projector has menus that make setting and adjustment easy.
1. Press the MENU button. The MENU screen appears on the screen.
User 1
Standard 1
Picture Adjust
Theater
Default
Fine Menu 1
Standard
1
Fine Menu 2
Dynamic
Default
1
Input Signal
User
1
2
Default
RGB/HD Adjust
3
HDMI
Picture Adjust
Gamma
Fine Menu 1
Contrast
0
B
Fine Menu 2
Brightness
0
C
Input Signal
Color
0
D
RGB/HD Adjust
Tint
0
E
HDMI
Sharpness
0
Theater
Display
Color Temp.
3
Standard
OSD/Blanking
Lamp Mode
Normal
Dynamic
Config.
Iris
1
A
A
Display
OSD/Blanking
Main menu
Config.
Picture mode
Index
Theater
Standard
Dynamic
User
Default, 1, 2, 3
Default, 1, 2, 3
Default, 1, 2, 3
1, 2, 3, 4, 5, 6, 7, 8, 9
Menu item
Setting or adjustment level
2.
Use the 3 and 4 buttons to select a menu (Picture Adjust, Fine Menu 1, Fine Menu 2, Input Signal,
RGB/HD Adjust, Display, OSD/Blanking, Config) and press the 2 button.
3.
4.
Use the 3 and 4 buttons to select a menu item and press the 2 button.
☞ P.24)
For image mode selection, see “Picture Mode”. (
– Theater: Reproduces the black suited for movie software.
5.
– Standard: Suited for normal movie software.
Use the 3, 4, 1 and 2 buttons to make the setting or adjustment of the selected item.
• The current setting or adjustment level is displayed to the right of each menu item.
Press the MENU button again to close the menu.
– Dynamic: Suited for visually dynamic image software.
☞ P.25).
2, 3, 4 1, 5
– User 1-9: Enable the user to adjust the gamma curve as preferred. (
BLANKING
B1
B2
V-MUTE
OFF
1, 5
MENU
M
Picture mode selection
There are two ways to select the Picture mode: selecting a mode from the MENU screen or pressing
the picture mode buttons (THTR, STD, DYN) on the remote controller. To use the remote controller
buttons to select a picture mode, make sure the MENU screen does not appear on the screen and
P.6)
press the desired picture mode button any number of times. (
To select an picture mode from the menu, do as follows.
1. Press the MENU button. The MENU screen appears on the screen.
2. Use the 3/4 buttons to select the Picture Mode displayed at the top of the menu.
3. Press the ENTER button to display the picture mode selection screen. Use the 3, 4, 2 and 1
buttons to select an picture mode.
4. Press the ENTER button to decide the selected picture mode. Once the mode has been
entered, the screen returns to the previous menu.
2, 3, 4
Memorizing settings in an index
The settings made in “Picture Adjust” and “Fine Menu 1” of the main menu are automatically
memorized in the currently selected picture mode. Therefore, first select an picture mode and index,
and then make settings.
Note : When default is selected, “Picture Adjust” and “Fine Menu 1” cannot be selected from the menu.
INPUT
ENTER
A
I
ASPECT
☞
24
B3
CINEMA
INFO.
VCR MODE
BLACK LEVEL
PATTERN
BLACK
– Adjustment bar
When there is a “ ” right of a menu item, this 2 acts as a button for engaging an adjustment mode. In
the adjustment mode, the menu disappears and only an adjustment bar, like that shown below,
appears along the bottom of the display. Use the 1 and 2 buttons to adjust the item to the desired
level. Press the 3 button to return to the menu.
Contrast
0
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ25
– Gamma setting
p.24) to User (1 – 9). Select “Gamma”
To change the type of Gamma curve, set the Picture Mode (
from the displayed menu followed by the desired gamma curve (A, B, C, D, E, Theater, Standard or
Dynamic).
Picture quality in each of the picture modes can be adjusted to your liking and those adjustments can be
saved in memory.
A
User 1
C
D
E
Theater
Picture Adjust
Gamma
Fine Menu 1
Contrast
0
Fine Menu 2
Brightness
0
Input Signal
Color
0
RGB/HD Adjust
Tint
0
HDMI
Sharpness
0
Display
Color Temp.
3
OSD/Blanking
Lamp Mode
Normal
Config.
Iris
1
Item
Gamma
Contrast
Brightness
Color
Tint
Sharpness
Color Temp.
(Color Temperature)
Lamp Mode
Iris
B
Dynamic
A
– Color Temp. (Color Temperature)
Adjustments
A, B, C, D, E, Theater,
Standard, Dynamic
-50Ô 0Ô 50
(Weak) (Default) (Strong)
-50Ô 0Ô 50
(Dark)
(Default) (Bright)
-50Ô 0Ô 50
(Light)
(Default) (Deep)
R10Ô 0Ô G10
(Purple) (Default) (Green)
0
50
1
2 3 4 5 HB
(Red)
(Blue)
Normal, Economy
1
2
3
Contrast (High)
(Low)
Brightness (Low)
(High)
Sets the lens and illumination
aperture.
1:
2:
3:
4:
5:
HB :
Red comes out strong. Color temperature is about 5250 K.
Red is mildly strong. Color temperature is about 5800 K.
Normal. Color temperature is about 6500 K.
Blue is mildly strong. Color temperature is about 7500 K.
Blue comes out strong. Color temperature is about 9300 K.
High Bright : Display brightest image.
NOTES:
- To adjust picture quality, set the index to a mode other than the default. See “Picture Mode”.
P.24)
(
P.24).
- The Gamma cannot be set unless User (1 - 9) is set for the Picture Mode (
P.22-23)
- Tint cannot be adjusted for RGB input. For details, see “Functions by Signal.” (
- The settings made in Picture Adjust are saved in the currently selected Picture Mode index.
☞
☞
☞
25
ENGLISH
☞
Picture Adjust
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ26
Fine Menu 1
Fine Menu 2
ENGLISH
By adjusting this Fine Menu, you can make fine picture adjustment.
Standard 1
Standard 1
Picture Adjust
Aspect
Full
Picture Adjust
Noise Reduction
0
Fine Menu 1
Cinema
Auto
Fine Menu 1
R Gain
0
Fine Menu 2
VCR Mode
On
Fine Menu 2
G Gain
0
Input Signal
Black Level
0 IRE
Input Signal
B Gain
0
RGB/HD Adjust
FRC
Auto 1
RGB/HD Adjust
R Bias
0
HDMI
CEC
HDMI
G Bias
0
Display
Picture Shift V
Display
B Bias
0
OSD/Blanking
Overscan
OSD/Blanking
Luminance Gain
0
Config.
Config.
Chroma Delay
0
Item
Noise Reduction
R Gain
G Gain
B Gain
R Bias
G Bias
B Bias
Luminance Gain
Chroma Delay
Off
0
0Ô
0Ô
0Ô
0Ô
0Ô
0Ô
0Ô
0Ô
50
50
50
50
50
50
50
50
5
– Noise Reduction
Adjust the noise reduction.
– R Gain
This menu allows the users to set the gain for red.
– G Gain
This menu allows the users to set the gain for green.
– B Gain
This menu allows the users to set the gain for blue.
– R Bias
This menu allows the users to set the bias for red.
– G Bias
This menu allows the users to set the bias for green.
– B Bias
This menu allows the users to set the bias for blue.
Cinema
VCR Mode
Black level
Enable
FRC
CEC
Picture Shift V
Overscan
Adjustments
0
-50Ô
-50Ô
-50Ô
-50Ô
-50Ô
-50Ô
-50Ô
-5Ô
Item
Aspect
– Cinema
Auto : Automatically selects the cinema mode when a video signal is input.
NTSC: 3-2 pull down, PAL: 2-2 pull down
Off :
Pull-down processing is not performed.
Adjustments
Full, Normal, Zoom,
V-Stretch, Through
Auto, Off
On, Off
0 IRE, 7.5 IRE /Expand,
Normal (For HDMI input)
Auto 1, Auto 2, 60Hz,
50Hz, 48Hz
On, Off
-50Ô 0 Ô 50
Enable, Disable
– VCR Mode
On :
A projector is forced into the intra-field only deinterlacing mode.
Off :
A projector is used with external field memories and operates in the full set of deinterlacing
modes, i.e., motion adaptive video deinterlacing and full frame film source deinterlacing
using 3:2 pulldown detection (2:2 pulldown for 625/50 sources).
– Black level
Select the black level by a video source.
– FRC (Frame Rate Conversion)
Auto 1 : Frame Rate Conversion function is basically off. However FRC turns on automatically
depending on vertical frequency of input signal. Normally, use this mode.
Auto 2 : Use this mode when the image stops momentarily.
60Hz : Frame Rate Conversion function is “On”. (59.94Hz fixed)
50Hz : Frame Rate Conversion function is “On”. (50.00Hz fixed)
48Hz : Frame Rate Conversion function is “On”. (47.95Hz fixed)
– CEC (Chroma Error Correction)
On :
Reduces CUE (Chroma Up-sampling Error) of 1080i signals.
Off :
Normally, use this mode.
– Picture Shift V
When Aspect on the Picture Adjust menu is set to “Zoom” or “V-Stretch”, this setting allows the user to
move the projected image vertically in order to see parts on the image not appearing on the screen.
– Chroma Delay
This menu allows the users to set the chrominance delay.
– Overscan
Selects whether to show or hide picture borders with NTSC, PAL, SECAM, 480i, 480p, 576i and 576p
signals.
Enable: Does not display borders of image signals. (Normally, use this mode.)
Disable: Displays the entire image signal.
Note :
Notes :
– Luminance Gain
This menu allows the users to set the luminance gain.
• The settings made in Fine Menu 1 are saved in the currently selected Picture Mode index (Default
excluded).
26
• There are some parameters can not adjust according to input signal.
• The settings made in Fine Menu 2 are saved in each currently selected input signal source.
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ27
RGB/HD Adjust
Standard 1
Standard 1
Picture Adjust
Component 1
Auto
Picture Adjust
Fine Menu 1
Component 2
Auto
Fine Menu 1
Readjust
Fine Menu 2
S-Video
Auto
Fine Menu 2
Resolution H
0
Input Signal
Video
Auto
Input Signal
Resolution V
0
RGB/HD Adjust
RGB
Auto
RGB/HD Adjust
Position H
0
HDMI
HDMI1
Auto
HDMI
Position V
0
Display
HDMI2
Auto
Display
Phase
0
OSD/Blanking
OSD/Blanking
Clamp Position
0
Config.
Config.
Clamp Width
0
Item
Component1,
Component2
S-Video
Video
RGB
Adjustments
Auto, 480i/576i, 480p, 540p, 576p,
720p, 1035i, 1080i, 1080p
Auto, NTSC, PAL, SECAM
Auto, NTSC, PAL, SECAM
Auto, 480i/576i, 480p, 540p, 576p,
720p, 1035i, 1080i, 1080p
Auto, 480i/576i, 480p, 576p, 720p,
1035i, 1080i, 1080p
HDMI 1, HDMI 2
Item
Mode
Readjust
Resolution H
Resolution V
Position H
Position V
NTSC(NTSC-3.58)
: Conventional analog broadcasting used
mainly in USA, Canada, Taiwan, Korea, and
Japan.
PAL(PAL-4.43)
: Conventional analog broadcasting used
mainly in United Kingdom and Germany.
SECAM
480p
540p
ENGLISH
Input Signal
: Conventional analog broadcasting used
mainly in France and Russia.
: Standard digital broadcasting
: Special digital broadcasting
(for example: RCA DTC100)
576p
: Standard digital broadcasting
720p, 1080p : High Definition digital broadcasting
1035i
: Japanese "Hi-Vision" broadcasting
Phase
Clamp Position
Clamp Width
123
Mode
Memory 1
Adjustments
Auto, Memory 1, Memory 2, Memory 3
Yes, No
0 Ô 25
(Default) (Large)
0 Ô 25
(Default) (Large)
-50Ô 0Ô 50
(Left)
(Default)
(Right)
-10Ô 0Ô 10
(Down) (Default)
(Up)
-10Ô 0Ô 10
(Backward) (Default) (Forward)
-50Ô 0Ô 50
(Backward) (Default) (Forward)
-50Ô 0Ô 50
(Small) (Default) (Large)
– Mode
Auto:
Each item is adjusted automatically.
Memory1-3: If something wrong with Auto Adjust, select Memory, please adjust each item manually.
– Readjust
Select to readjust settings automatically for each item in this menu.
– Resolution H, V
Adjusts the horizontal and vertical resolution of the RGB/HD input signals.
– Position H, V
Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the
vertical position of the input signal.
– Phase
Adjust the phase of the DMD dots and the computer signal input from the RGB IN. Adjust the picture
to where it looks clearest.
– Clamp Position, Width
Adjusts the clamp position and width used in RGB/HD input.
27
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ28
HDMI
Display
ENGLISH
Standard 1
Item
Standard 1
Picture Adjust
CSC HDMI 1
Auto
Picture Adjust
Keystone
0
Fine Menu 1
CSC HDMI 2
Auto
Fine Menu 1
Scale
0
Fine Menu 2
Deep Color HDMI 1
Auto
Fine Menu 2
Width
0
Input Signal
Deep Color HDMI 2
Auto
Input Signal
Position H
0
0
RGB/HD Adjust
RGB/HD Adjust
Position V
HDMI
HDMI
Installation
Display
Display
OSD/Blanking
OSD/Blanking
Config.
Config.
Keystone
(Electronic vertical
keystone correction)
Scale
Front
Width
Position H
Position V
Item
CSC HDMI 1,
CSC HDMI 2
Adjustments
Auto, RGB, YPBPR 4:4:4, YPBPR 4:2:2,
YCBCR 4:4:4, YCBCR 4:2:2
Select the color space conversion for
HDMI input.
Deep Color HDMI 1,
Deep Color HDMI 2
Auto, 8Bit, 10Bit, 12Bit
Select the color depth for HDMI input.
– CSC HDMI 1/CSC HDMI 2
Auto: The color space is automatically selected based on the input signal.
RGB:
This is effective for DVI and similar signals.
YPBPR: This is effective for 720p, 1080i, and other high-resolution TV signals.
YCBCR: This is effective for 480p, 480i, and other standard TV signals.
– Deep Color HDMI 1/Deep Color HDMI 2
Auto:
This automatically selects the color depth based on the input signal.
Normally, use at Auto.
8/10/12bit: Select this option when the video displayed in Auto is not correct.
The input settings for the color depth are set to 8Bit, 10Bit, and 12Bit.
Installation
Adjustments
-25
(
0
)
(
25
)
)
-100
0
(Min)
(Max)
-100
0
(Max)
(Min)
-50
0
50
(Left) (Default) (Right)
-50
0
50
(Down) (Default) (Up)
Front, Rear, F+Ceiling,
R+Ceiling
– Keystone
Adjust trapezoid image to rectangle image.
– Scale
Reduces the image without changing the aspect ratio. The image can be reduced to about 70% the
original size.
– Width
Reduces the image width without changing the image height. The width can be reduced to about 75%
the original size.
– Position H, V
Adjust the position of the input signal. H adjusts the horizontal position of the input signal. V adjusts the
vertical position of the input signal.
– Instllation
Sets the installation mode of the projector.
Front: Select to set the projector on a tabletop and project from in front of the screen.
Rear: Select to set the projector on a tabletop and project from behind the screen.
F + Ceiling: Select to mount the projector on the ceiling and project from in front of the screen.
R + Ceiling: Select to mount the projector on the ceiling and project from behind the screen.
28
(
– Blanking Top, Bottom, Left and Right
Set the blanking width of the top, bottom, left and right masks, which are then memorized in Memory 1
– 3 of Blanking Memory. Each can be set from 0 (no mask) to a maximum 100.
OSD/Blanking
Standard 1
Picture Adjust
Menu Position
Top-L
Fine Menu 1
Language
English
Fine Menu 2
Status Info.
Enable
Input Signal
Power-OFF Confirm. Disable
RGB/HD Adjust
Blanking Memory
HDMI
Blanking Top
0
Display
Blanking Bottom
0
OSD/Blanking
Blanking Left
0
Config.
Blanking Right
0
Item
Menu Position
Language
Status Info.
Power-OFF Confirm.
Blanking Memory
Blanking Top
Blanking Bottom
Blanking Left
Blanking Right
Memory 1
Adjustments
Top-L, Top, Top-R, Center-L, Center, Center-R,
Bottom-L, Bottom, Bottom-R
English, Deutsch, Français, Español,
Português, Italiano
Enable, Disable
Enable, Disable
Off, Memory 1, Memory 2, Memory 3
0
100
0
100
0
100
0
100
– Menu Position
OSD position is selected from 9 positions.
– Status Info.
Enable: Displays the current status of the projector for a set amount of time in the upper right-hand
corner of the screen at startup and whenever the Input Source, Picture Mode, Aspect ratio or
other setting is changed.
Disable: Does not display Status Info.
– Power-OFF Confirm.
Disable: Directly puts the projector on standby without displaying the confirmation message when power
is shut off from the
button on the remote controller or the /I button on the projector.
Enable:
Displays a confirmation message asking whether to shut the power off or continue use
when power is shut off from the
button on the remote controller or the /I button on the
projector. To shut off the power immediately, select “Yes” and press the ENTER button. To
not shut off the power, select “No” and press the ENTER button.
– Blanking Memory
Sets the blanking mode with which part of the screen can be hidden in black bands. To use this mode
or change the setting, select from Memory 1 to 3.
Off:
Turns the blanking mode off. No masking occurs.
Memory 1-3:
Memorize the blanking width of the top, bottom, left and right masks set with the
below features. Up to three settings can be memorized.
29
ENGLISH
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ29
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ30
– Remote Control
Wireless: Set to use the included remote controller.
Wired:
Set to control the projector from either Marantz’s AV components connected to the
REMOTE CONTROL IN/OUT terminals or a PC or other device connected to the RS232C terminal of the projector. The included remote controller cannot be used in this case.
When this item is selected, a confirmation message appears asking whether to change the currently
selected mode to the other mode or not. To change the mode, select “Yes” and press the ENTER
button on the projector. To keep the same mode, select ‘No” and press the ENTER button.
Configration
ENGLISH
Standard 1
Picture Adjust
Auto Power Off
Disable
Fine Menu 1
Trigger 2 Full
On
Fine Menu 2
Trigger 2 Normal
On
Input Signal
Trigger 2 Zoom
On
RGB/HD Adjust
Trigger 2 V-stretch
On
HDMI
Trigger 2 Through
On
Display
Remote Control
OSD/Blanking
Reset Lamp Life
Config.
Reset All
Item
Auto Power Off
Trigger 2 Full
Trigger 2 Normal
Trigger 2 Zoom
Trigger 2 V-stretch
Trigger 2 Through
Remote Control
Reset Lamp Life
Reset All
Notes:
- To prevent misoperation, the ENTER button of the remote controller does not respond to touch
when the Wired/Wireless setting is displayed. Press the ENTER button of the projector to enter the
setting.
- To change from Wired to Wireless, set “Wireless” from the menu using the buttons of the projector.
Adjustments
Enable, Disable
On, Off
On, Off
On, Off
On, Off
On, Off
Wireless, Wired
Yes, No
Yes, No
– Auto Power Off
When the auto power off feature is set to Enable, power
to the projector automatically shuts off if no signals are
received and no operations are performed for about 10
consecutive minutes. If 9 minutes pass without the
projector receiving any signals or being operated in
anyway, the below message appears on the screen.
– Reset Lamp Life
If the lamp is replaced before reaching its 2000 hours
lamp life, be sure to reset the lamp’s life counter. To do
this, select “Reset Lamp Life” from the Configuration
menu. When the user selects this item, the following
message appears:
Select “Yes”, and press the ENTER button. Then the
lamp life is initialized.
Auto Power Off
It will be standby mode soon.
About 1 minute after the message appears on the screen, power to the projector shuts off.
Note:
After the above message appears on the screen, pressing any button on the projector or remote
control other than the
/ I button on the projector and the ON or STANDBY buttons on the remote
control resets the auto power off feature.
The auto power off feature will activate again if, after that, the projector goes without receiving any
signals or being operated in anyway for 10 consecutive minutes.
– Tigger 2
Select either 12V output or 0V output by choosing On or Off for each aspect mode. Full, Normal,
Zoom, V-stretch and Through.
This allows you to control such as a powered dual aspect screen with the outputs for the aspect
modes.
On: Output DC 12V.
Off: No output.
30
– Reset All
All settings are reset to the factory default settings except
the lamp life.
When the user selects this item, the following message
appears:
Select “Yes”, and press the ENTER button.
Reset Lamp Life ?
Yes
No
Reset All ?
Yes
No
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ31
❖ Initialize the Lamp Life
Lamp Life and Replace Lamp
❖ Lamp Life
– When the lamp life becomes less than 100
hours and the unit is still on, the remaining
lamp life is displayed on the screen
automatically.
Display the remaining lamp life by pressing the
INFO. button on the remote controller.
The lamp has a lamp life of 2000 hours. The
projector is designed to shut OFF power if the lamp
is used beyond this 2000 hours lamp life. In such
case, replace the lamp and reset the lamp life
counter as follows.
1.
After the message “Lamp Life 0 Hours”
appears, power to the projector shuts OFF.
Promptly replace the lamp with a new one.
(
P.31 “Replacing Lamp Unit”)
2.
Once the lamp has been replaced, press the
ON button on the remote control or the
/I
button on the projector.
☞
Warning
Lamp Life 100 Hours
Information
Video Input
Component 1 - 1080i / 60
Picture Mode
User 1
Gamma
A
Aspect
Normal
Lamp Mode
Economy
Iris
1
The below message appears on the screen
for 120 seconds.
– When the lamp life becomes less than 5 hours,
the remaining lamp life is displayed on the
screen .
Lamp Life
921 Hours
Total Time
3653 Hours
Yes
INPUT
ENTER
A
I
ASPECT
INFO.
CINEMA
VCR MODE
BLACK LEVEL
Lamp Life 5 Hours
3.
4.
PATTERN
A1
A2
RGB
G3
THTR
STD
DYN
G4
B1
B2
CAUTION:
• Do not touch the lamp and the lamp unit
carelessly. It is extremely hot. Wait at least
one hour for the lamp to cool down before
handling.
• Do not loosen any screws except for those
mentioned below.
• The lamp may break if handled improperly.
• Do not use other than a Marantz
replacement lamp unit.
❖ How to replace the Lamp Unit
PREPARATION:
When replacing the lamp, turn off the power for
the projector. After the cooling fan stops,
disconnect the power cord and wait for one
hour until the lamp is cooled down completely,
then replace the lamp.
New Lamp ?
Warning
Replacing Lamp Unit
No
Select “Yes”, using the 1 / 2 buttons.
1.
Press the ENTER button. The lamp life
indicator is now initialized.
Press the STANDBY button on the remote
controller or the
/ I button on the projector
to turn the projector off.
BLANKING
BLACK
V-MUTE
B3
OFF
3.
MENU
STANDBY
ON
M
Notes:
• The maximum life limit of the lamp is 2000
hours. Although we care very much about
quality, the lamp can rarely breaks down if
running time exceeds 1000 hours. Therefore
we recommend to replace the lamp if Lamp
Life gets under 1000 hours. The lamp
cannot be used exceeding the maximum life
limit.
• This product is checked under strict quality
control when it is shipped out form factory.
“Total Hours” in the menu includes the time
for this check. So “Total Hours” may not be 0
hours when it is used first time.
– Approximately 2 minutes after the lamp
reaches the end of its lamp life, power to the
projector shuts OFF and the WARNING
indicator lights up a yellow color. If the below
message appears on the screen and power
shuts OFF soon thereafter, promptly replace
the lamp with a new one. (See “Replacing
P.31)
Lamp Unit”
Warning
Lamp Life 0 Hours
C.TEMP
GAMMA
COMP.1
COMP.2
S-VIDEO
USER
C1
C2
S
HDMI 1
HDMI 2
VIDEO
V
G2
G1
RGB
G3
I
To clear the warning, press the MENU button.
☞
LAMP
INPUT
ENTER
A
IRIS
4.
2.
H1
H2
AUX 1
AUX 2
A1
A2
After the cooling fan stops, Unplug the AC
power cord.
2.
STANDBY
ON
IRIS
LAMP
C.TEMP
GAMMA
COMP.1
COMP.2
S-VIDEO
USER
C1
C2
S
HDMI 1
HDMI 2
VIDEO
H1
H2
V
G2
AUX 1
AUX 2
2.
G1
A1
A2
RGB
G3
THTR
STD
DYN
G4
BLANKING
B1
B2
V-MUTE
B3
OFF
MENU
M
4.
INPUT
ENTER
A
I
INFO.
ASPECT
CINEMA
VCR MODE
BLACK LEVEL
PATTERN
3.
BLACK
31
ENGLISH
MAINTENANCE
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ32
3.
Wait at the least one hour for the lamp and
lamp unit to cool down.
ENGLISH
4.
5.
Remove the lamp cover screw.
8.
Holding the handle and pull the lamp unit out
toward your side.
11. Install the lamp cover back in its original
position and fasten with the fastening screw.
(a)
Read the caution and warning labels on the
unit.
Lamp cover
Lamp unit
A
WARNING
THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
CAUTION : HIGH PRESSURE LAMP CAUTION HOT : UNPLUG
MAY EXPLODED IF IMPROPERLY HANDLED. THE POWER CORD AND WAIT
REFER SERVICING TO QUALIFIED SERVICE 60 MINUTES BEFORE CHARGING
PERSONNEL.
THE LAMP.
ATTENTION : LA LAMPE SOUS
HAUTE PRESSION PEUT SI ELLE, N'EST
PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN
PERSONNEL D'ENTRETIEN QUALIFIE.
ATTENTION CHAUD :
SERIAL NO.
DEBRANCER LE CORD ON
D'ALOMENTION ET ATENDER
60 MINUTES AVANT DE
CHANGER LAMPE.
B
A
For USA
(b)
WARNING
6.
THIS COVER IS PROVIDED WITH
INTERLOCK TO REDUCE THE RISK OF
EXCESSIVE ULTRAVIOLET RADIATION.
DO NOT DEFEAT ITS PORPOSE OR
ATTEMPT TO SERVICE WITHOUT
REMOVING COVER COMPLETELY.
Remove the lamp cover in the direction of the
arrow.
9.
Install a new lamp unit in position securely.
For Europe
CAUTION HOT
UNPLUG THE POWER CORD AND
WAIT 60 MINUTES BEFORE
CHANGING THE LAMP.
Lamp cover
ATTENTION CHAUD
DEBRANCER LE CORD ON
D'ALIMENTION ET ATENDER 60
MINUTES AVANT DE CHANGER
LAMPE.
12. Plug in the video projector and turn on the
power and project the image.
WARNUNG HEISS
ZIEHEN SIE DEN NETZSTECKER
AB UND WARTEN SIE 60 MINUTEN,
BEVOR SIE DIE GLUHLAMPE
WECHSELN.
☞
B
10. Lock the lamp unit in place with the two
For USA
7.
CAUTION : HIGH PRESSURE LAMP CAUTION HOT : UNPLUG
MAY EXPLODED IF IMPROPERLY HANDLED. THE POWER CORD AND WAIT
REFER SERVICING TO QUALIFIED SERVICE 60 MINUTES BEFORE CHARGING
PERSONNEL.
THE LAMP.
ATTENTION : LA LAMPE SOUS
HAUTE PRESSION PEUT SI ELLE, N'EST
PAS MANIPULEE CORRECTEMENT,
CONFIER L'OPERATION A UN
PERSONNEL D'ENTRETIEN QUALIFIE.
ATTENTION CHAUD :
Open the cover sheet and remove the two
screws (slotted head screwdriver required)
lock /down
MODEL NO. that
VP-12S1
N1S the lamp unit. Do not remove
anyZother
screws.
AC 120V 60H
2.0W
SERIAL NO.
DEBRANCER LE CORD ON
D'ALOMENTION ET ATENDER
60 MINUTES AVANT DE
CHANGER LAMPE.
For Europe
CAUTION
VORSICHT :
HIGH PRESSURE LAMP MAY EXPLODED IF BEI FALSCHER HANDHABUNG M
IMPROPERLY HANDLED. REFER SERVICING KANN DIE HOCHDRUCKLAMPE
EXPLODIEREN UBERLASSEN
TO QUALIFIED SERVICE PERSONNEL.
SIE WARTUNGSARBEITEN
ATTENTION
NUR FACHPERSONAL.
LA LAMPE SOUS HAUTE PRESSION PEUT
EXPLOSER SI ELLE, N'EST PAS MANIPULEE
CORRECTEMENT, CONFIER L'OPERATION
A UN PERSONNEL D'ENTRETIEN QUALIFIE.
32
• If the lamp is replaced before reaching its
2000 hours lamp life, see “Reset Lamp Life”
(
P.30).
• If the lamp is replaced after reaching its
2000 hours lamp life, see “Initialize the Lamp
Life” (
P.31).
MADE IN JAPAN
FABRIQUE AU JAPON
Cover sheet
screws removed in step 7. Press on the
handle until it folds over and close the cover
sheet.
☞
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ33
If the lens becomes dirty or smudged, clean it with
a soft dry cloth only. Use optical lens cleaners that
are approved for eyeglasses or cameras. Do not
use a dampen cloth, detergent solution, or thinner.
It may damage the lens and remain as stains.
Optional Accessories
ENGLISH
Cleaning the Lens
Lamp Unit : LU-12VPS3
Replacement Parts
When replacement parts are required, be sure to
inform a Marantz authorized service center. Use
only replacement parts specified by Marantz.
Unauthorized substitutions may result in fire,
electric shock, or other hazards. And, the warranty
may not be guaranteed.
Ceiling Mount kit : MOUNT 20
This kit is specially designed to mount the unit
on ceiling.
Extension Pole : EXT-10
This tool is to adjust height with the Ceiling
Mount Kit MOUNT 20.
CAUTION:
For ceiling installation, consult with the
Marantz Authorized dealer.
33
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ34
ENGLISH
TROUBLESHOOTING
Try the following troubleshooting before calling for service.
1.
2.
Are the connections made properly ?
Are you operating the unit properly, following the instructions ?
If the unit does not operate properly, check the items shown in the following table.
If any trouble cannot be solved by the instructions below, malfunction of the internal circuitry is suspected; immediately unplug the AC power cord and contact
Marantz dealer or service center.
Symptom
No power
Image is not
displayed.
Poor color.
Picture is too dark.
Picture is not clear.
Picture rolls.
The Remote
Controller does not
work.
Possible Cause
Remedy
AC power cord is not connected correctly.
Connect the AC power cord properly.
Lamp cover is not closed correctly.
Close the cover properly. (
A signal cable is not connected correctly.
Connect a signal cable properly.
Selected input is incorrect.
Select the correct input source. (
The picture mute is active.
Press the V-MUTE button to release the mute.
Picture is not adjusted properly.
Adjust the picture in the MENU mode.
Lamp life is running out.
Replace the lamp. (
Contrast or brightness is not adjusted properly.
Adjust contrast or brightness properly.
Picture is out of focus.
Adjust the focus. (
Dew is on the lens.
Run the projector for about two hours.
A signal cable is not properly connected.
Connect a signal cable properly.
Batteries are exhausted.
Replace batteries. (
The distance to the unit is too far.
Make the distance between the unit and the remote control
closer. (
P.8)
IR sensor on unit is obstructed.
Remove any obstacles.
The “Wired” position in the Menu is selected.
Select the “Wireless” position. (
☞ P.32)
☞ P.18)
☞ P.31)
☞ P.11)
☞ P.8)
☞
☞ P.30)
Notes:
• If the lamp still does not function after the replacement and initialization of the lamp life, contact a Marantz authorized dealer, or service center.
• This projector uses a microcomputer. External noise can cause malfunctions. In such case, shut power OFF and unplug the power cable from AC power
outlet. Then, plug the AC power cable back in, press the
/ I button on the projector or the ON button on the remote control and check operation.
34
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ35
GLOSSARY
WARNING/LAMP indicator, ON indicator, and STANDBY indicator diagnose error mode of the projector as follows.
Aspect ratio
Indicators
Error mode
Lamp cover
WARNING
/LAMP
ON
ON
OFF
STANDBY
Flashing
Possible Cause
Close the cover correctly.
Replace the lamp and
reset lamp life.
Lamp
ON
OFF
OFF
Temperature
Flashing
OFF
Flashing
Projector internal
temperature is higher
than the allowed level.
Fan
Other
Flashing
Flashing
OFF
OFF
ON
OFF
Recommendation
The lamp cover is not
closed properly.
The lamp has failed, or
the lamp is completely
worn out.
Trouble has occurred
with the fan.
Internal program error
ENGLISH
ERROR MODE
Check if anything is
blocking the exhaust vent.
Width and height ratio of an image. The normal
aspect ratio of a computer and video image is 4 :
3. There are also wide images with an aspect
ratio of 16 : 9 and 21 : 9.
Black Level (Black setup)
The signal level which represents black picture
intensity.
For NTSC system for USA, this level is 7.5IRE.
NORMAL: 16 (Black) – 235 (White)
For NTSC system for Japan and DVD, this level
is 0IRE.
EXPAND: 0 (Black) – 246 (White)
Color Temperature
Shut power OFF and
ON again.
White color hue.
Low color temperature implies a warmer (more
yellow/red) light.
High color temperature implies a colder (more
blue) light.
Keystone
Distortion of the image caused by projection to a
wrong vertical angle.
ON SCREEN MESSAGE
Use the list below to check the message displayed on the screen.
Message
Meaning
Remedy
NO SIGNAL
No input signal.
Properly connect the cables.
REPLACE LAMP!
The lamp has reached the end of its life.
Replace the lamp and reset lamp life.
Improper signal feed to the projector.
Adjust resolution, V(Hz) : refresh rate of the
equipment, referring to the Timing Chart.
OUT OF RANGE
35
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ36
❖ Timing chart
ENGLISH
SPECIFICATIONS
❖ Optical characteristics
❖ General
Panel
1080p DLP®
(1920 x 1080 pixels)
Power requirement
For USA: AC 120V/60Hz
For Europe: AC 230V/50Hz
Lamp
Super High Pressure 200W DC
Power consumption
< 350 W
Lens
VP-15S1: f: 30.7 to 44.5mm
VP-15S1L: f: 44.5 to 66.75mm
Standby consumption For USA: < 0.3 W (AC 120V)
For Europe: < 0.5 W (AC 230V)
Projection size
70 to 250 inches
Chassis isolation
Class-1
Safety
UL60950-1
CSA C22.2 E60950
EN60950-1
EMC
FCC Part-15 Class-B
EN55022 Class-B
Dimensions
VP-15S1:
15 15/16(W) x 18 5/16(D)
x 6 1/8(H) inch
404.5(W) x 489.5(D) x 158(H) mm
VP-15S1L:
15 15/16(W) x 19 19/32(D)
x 6 1/8(H) inch
404.5(W) x 497.5(D) x 158(H) mm
D-sub M 15 pin x 1
Analog RGB
HD:1080i, 720p, 480p
Net weight
13 kg
HDMI x 2
HDMI 1.3 compliant
(single link only)
Operating humidity
REMOTE
CONTROLLER IN
Mini jack type x 1
Storage humidity
REMOTE
CONTROLLER OUT
Mini jack type x 1
❖ Accessories
AC IN
3 Prong Grounding Type
TRIG.1 OUT,
TRIG.2 OUT
Mini Jack x 2
Output: DC12V or 0V
RS-232C
RS-232C receptacle plug x 1
❖ Input/Output
VIDEO IN
RCA x 1
NTSC-3.58/PAL-4.43/SECAM
Composite video 1.0Vp-p/
75 Ohm
S-VIDEO IN
S-Connector x 1
NTSC-3.58/PAL-4.43/SECAM
S-Video
COMPONENT
3RCA x 2
Y, CB/PB, CR/PR
IN
RGB/HD IN
HDMI IN
OperatingTemperature 5 to 35 °C
30 to 85%
Storage Temperature – 20 to 60 °C
•
•
•
•
•
•
30 to 85%
Lens cap x 1
Remote controller x 1
Batteries x 2
AC power code x 1
User Guide x 1
Warranty Card
(1 copy each for USA, CANADA)
Comes with USA model only.
Specifications may be subjected to change without any prior notice.
36
Format
NTSC 3.58
NTSC 4.43
PAL-B/G
PAL M
PAL N
PAL 60
SECAM
480/60i
480/60p
576/50i
576/48p
576/50p
540/60p
720/24p
720/25p
720/30p
720/50p
720/60p
1035/60i
1080/50i
1080/60i
1080/24PsF
1080/25PsF
1080/30PsF
1080/24p
1080/25p
1080/30p
1080/50p
1080/60p
640 x 350@70Hz
640 x 350@85Hz
640 x 400@70Hz
640 x 400@85Hz
640 x 480@60Hz
640 x 480@72Hz
640 x 480@75Hz
640 x 480@85Hz
800 x 600@56Hz
800 x 600@60Hz
800 x 600@72Hz
800 x 600@75Hz
800 x 600@85Hz
1024 x 768@60Hz
1024 x 768@70Hz
1024 x 768@75Hz
1024 x 768@85Hz
1280 x 1024@60Hz
1600 x 1200@60Hz
Resolution
720 x 487
720 x 483
720 x 576
720 x 576
720 x 576
1920 x 540
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1280 x 720
1920 x 1035
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
640 x 350
640 x 350
640 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
1600 x 1200
V (Hz)
59.94 / 60
59.94 / 60
50
59.94 / 60
50
59.94 / 60
50
59.94 / 60
59.94 / 60
50
48
50
59.94 / 60
23.98 / 24
25
29.97 / 30
50
59.94 / 60
59.94 / 60
50
59.94 / 60
23.98 / 24
25
29.97 / 30
23.98 / 24
25
29.97 / 30
50
59.94 / 60
70
85
70
85
60
72
75
85
56
60
72
75
85
60
70
75
85
60
60
H (KHz)
15.734/15.75
15.734/15.75
15.625
15.734/15.75
15.625
15.734/15.75
15.625
15.734/15.75
31.469/31.5
15.625
30
31.25
33.746/33.78
17.985/18
18.75
22.478/22.5
37.5
44.955/45
33.716/33.75
28.125
33.716/33.75
26.978/27
28.125
33.716/33.75
26.978/27
28.125
33.716/33.75
62.5
67.433/67.5
31.469
37.861
31.469
37.861
31.469
37.861
37.5
43.269
35.156
37.879
48.077
46.875
53.673
48.363
56.476
60.023
68.678
63.981
75
Comp.1/2 CVBS/S-Video
RGB
HDMI
9/16 - 2 7/16
(15.0 - 61.8)
6 12/16 (171.0)
4 1/8
(105.0)
6 1/16
(153.5)
7 3/16
(182.5)
3 1/4
( 82.6)
❖ Front
6 12/16 (171.0)
11 11/16 (296.5)
10 5/16 (262.0)
16
2 8/ )
4
( 6
5 9/16
(141.0)
7 5/16
(185.25)
5 3/4
(145.75)
4 11/16
(110.0)
3 11/16
(93.5)
8 12/16
(222.0)
4 1/8
(105.0)
6 1/16
(153.5)
1 10/16 2 5/16
(42.0) (58.0)
❖ Rear
14 6/16 (346.5)
19 9/16 - 19 19/32 (496.5 - 497.5)
❖ Top
4 11/16 (119.0)
12/16
(19.75)
3 - 3 9/16 (76.0 - 91.0)
8 12/16
(222.0)
5 5/8 (143.0)
❖ Bottom
5 3/16 (132.0)
❖ Front
16
VP-15S1
9/16 - 2 7/16
(15.0 - 61.8)
3 1/4
( 82.6)
2 8/ )
4
( 6
5 9/16 - 5 5/8
(142-143)
5 3/4
(145.75)
3 11/16
(93.5)
1 10/16 2 5/16
(42.0) (58.0)
14 6/16 (346.5)
11 11/16 (296.5)
10 5/16 (262.0)
18 1/4 - 18 5/16 (488.5 - 489.5)
❖ Top
4 11/16 (119.0)
7 3/16
(182.5)
3 - 3 9/16 (76.0 - 91.0)
5 5/8 (143.0)
5 3/16 (132.0)
DIMENSIONS
VP-15S1L
ENGLISH
VP-15S1_U_01_ENG 07.7.5 11:05 AM ページ37
❖ Bottom
7 5/16
(185.25)
4 11/16
(110.0)
12/16
(19.75)
❖ Rear
Unit : inch (mm)
37
VP-15S1_U_07_Note 07.7.5 11:12 AM ページ1
Note
VP-15S1_U_cover 07.7.5 11:01 AM ページ9
www.marantz.com
You can find your nearest authorized distributor or dealer on our website.
is a registered trademark.
Printed in Japan
07/2007 00M29AV851250 mzh-g
Download PDF