Wohler | RMT-173-TT | User guide | Wohler RMT-173-TT User guide

RMT-173 Series
• RMT-173-RM
• RMT-173-TT
Dual Input, LCD, Multi-Viewer Audio/
Video Monitors
User Guide
Part Number 821100, Revision A
© 2013 Wohler Technologies, Inc. All rights reserved.
This publication is protected by federal copyright law. No part of this publication may be
copied or distributed, stored in a retrieval system, or translated into any human or computer
language in any form or by any means electronic, mechanical, manual, magnetic, or otherwise,
or disclosed to third parties without the express written permission of Wohler Technologies.
Reproduction
Licensed users and authorized distributors of Wohler Technologies, Inc. products may copy
this document for use with Wohler Technologies., Inc. products provided that the copyright
notice above is included in all reproductions.
Customer Support
Wohler Technologies, Inc.
31055 Huntwood Avenue
Hayward, CA 94544
www.wohler.com
Phone: 510-870-0810
FAX: 510-870-0811
US Toll Free: 1-888-596-4537
(1-888-5-WOHLER)
Web: www.wohler.com
Sales: sales@wohler.com
Support: support@wohler.com
Disclaimers
Even though Wohler Technologies, Inc. has tested its equipment and software, and reviewed
the documentation, Wohler Technologies, Inc. makes no warranty or representation, either
express or implied, with respect to software, documentation, their quality, performance,
merchantability, or fitness for a particular purpose.
Wohler Technologies, Inc. reserves the right to change or improve our products at any time and
without notice.
In no event will Wohler Technologies, Inc. be liable for direct, indirect, special, incidental, or
consequential damages resulting from any defect in the hardware, software, or its
documentation, even if advised of the possibility of such damages.
Some states do not allow the exclusion or limitation for incidental or consequential damages, so
the above exclusion or limitation may not apply to you.
Printing
This document is intended to be printed on a duplex printer, such that the copy appears on
both sides of each page. This ensures that all new chapters start on a right-facing page.
This document looks best when printed on a color printer since some images may be indistinct
when printed on a black and white printer.
Last Update
October 17, 2013
8 21 10 0 :
ii
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RMT-173 Series
Introduction
Overview
The RMT-173 Series dual input, LCD video monitors are highperformance, professional LCD monitors that support advanced 12-bit
digital processing technology with 3D comb filter and de-interlace,
accurate scaling engine, GAMMA correction and color temperature
adjustments to achieve the best possible image display.
The RMT-173 Series supports 2-channel 3G/HD/SD-SDI, Y/C,
component, and CVBS signal inputs as well as a single HDMI signal
input. Each model can simultaneously display two signal inputs, with
three display modes including one full screen display, Picture-InPicture (PIP) displays or two Picture-By-Picture (PBP) uniform size
screen displays.
Topics
Topics
Introduction
Page
1
Safety
2
Installation Recommendations
3
Unpacking and Installation
4
Features
7
Front Panel Features
8
Rear Panel Features
11
Using the Menu System
15
Specifications
29
Technical Function Overview
32
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 2 0 1 3 Wo hl e r Te c hno lo g i e s, In c. A ll r ig h ts re se r v ed .
1
RM T - 1 73 Se r ie s
Sa f e t y
Safety
Important Safety Instructions
IMPORTANT:
1.
Read, keep, and follow all of these instructions; heed all warnings.
2.
Do not use this equipment near water, rain or moisture.
3.
Use only a dry cloth to clean the equipment.
4.
Do not install near any heat source such as a radiator, heat register,
amplifier, or stove.
5.
Do not attempt to plug the unit into a two-blade outlet (with only
two prongs of equal width).
By design, these monitors will only plug into a three-prong outlet for
your safety. If the plug does not fit into your outlet, contact an
electrician to replace the obsolete outlet.
6.
Protect the power cord from being walked on or pinched,
particularly at plug’s source on the equipment and at the socket.
7.
Use only the attachments/accessories specified by the
manufacturer.
8.
Unplug the equipment during lightning storms or when unused
for long periods of time.
9.
Use of a cart is neither recommended nor approved by Wohler.
10. Refer all servicing to qualified service personnel. Servicing will be
required under all of the following conditions:
8 21 10 0 :
2
•
The equipment has been damaged in any way, such as when
the power-supply cord or plug is damaged.
•
Objects have fallen onto the equipment; or the equipment has
been exposed to rain or moisture, or liquid has been spilled
onto the equipment.
•
The equipment does not operate normally.
•
The equipment has been dropped.
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RMT-173 Series
I n s t a l la t io n R e c om m e n d a t io n s
Safety Symbols
WARNING:
The symbol to the left warns of electric shock hazard inside the unit.
Disconnect the power cord before removing access panels when
installing upgrades. Only qualified service personnel are to operate the
equipment with covers removed, and are to exercise caution to avoid
personal injury.
Installation Recommendations
Heat Dissipation
The ambient temperature around the unit should not exceed 40°
Celsius (104° Fahrenheit). Allow plenty of space around the unit for air
circulation.
Mounting/Bracing
A table top (-TT) stand or rack mount (-RM) kit may be provided. A
standard VESA 100 mounting hole pattern is provided on the back of
the unit for use with other mounts (not supplied).
Refer to Mounting on page 5 for instructions on attaching the desktop
stand.
Connections and Cable Recommendations
We recommend that you limit the length of the cables that you use for
feeding HD-SDI signals sources to the HD-SDI inputs of the RMT-173
Series units and that you use a Belden 1694A cable (or equivalent). The
HD-SDI inputs (IN1 and IN2) can be up to 150 meters (492 feet) in
length for 1.5 Gbps (HD), more for 270 Mbps (SD) and less for 3Gbps.
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
3
RM T - 1 73 Se r ie s
U n p a ck in g a n d I n s t a ll a t io n
Note:
HDMI 1.3 or 1.4 cable lengths of 2m (6 feet) are guaranteed
to work well. Four meters (12 feet) lengths of high quality
cable should work well enough, but is not guaranteed for all
situations. Longer HDMI cables often degrade signal
quality. Active extender transmitter/receiver pairs can be
used to cover long distances.
Electrical Interference
Be careful to properly terminate/ground signals and avoid
mismatched cable types and other similar causes of undesired
reflections in digital signal systems. If severe enough, such reflections
can result in corruption of the digital data stream. As with any audio
equipment, maximum immunity from electrical interference requires
the use of shielded cable. The internal circuitry ground is connected to
the chassis.
Power
The unit comes with a standard 12 VDC/5 A external power adapter
and connects an A/C mains power source (65W, 100 to 240 VAC, 50/
60Hz) through the IEC connector provided on the power adapter.
When the mains plug or appliance coupler is used as the disconnect
device, the disconnect device connection should remain accessible to be
operable.
Unpacking and Installation
Contents
While unpacking the components, verify that none of the components
are damaged. The selected stand or mounting kit comes in a separate
box.
Also verify that the box contains all of the following:
• Monitor
8 21 10 0 :
4
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RMT-173 Series
U n p a c k in g a nd I n s t a ll a t io n
• Adapter (12 VDC)
• Power cord
• User guide CDROM
• Warranty card
Mounting
The RMT-173 Series monitors come standard with either a table top
base (RMT-173-TT) or rack ears (RMT-173-RM). A standard VESA 100
pattern accommodates other user-supplied mountings, such as for
walls.
To install the table-top base, refer to Figure 1–1 and the instructions that
follow. Refer to the instructions included with other mounts when
used.
Figure 1–1
RMT-173-RM Bracket Installation
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
5
RM T - 1 73 Se r ie s
U n p a ck in g a n d I n s t a ll a t io n
1.
Place the monitor face down on a smooth surface and, as shown in
Figure 1–1, use a screwdriver and the supplied round head screws
to fasten the bracket to the back of the monitor.
Figure 1–2
8 21 10 0 :
6
RMT-173-RM Base Installation
2.
Next, again using a screwdriver, attach the base to the bracket,
with the supplied flat head screws, as shown in Figure 1–2.
3.
Place the monitor upright on a solid static-free surface.
4.
Connect the signal inputs to the rear panel.
5.
Connect the power cord to the rear panel of the monitor and to
mains power.
6.
Set the Power switch on the rear panel of the monitor to On (1).
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RMT-173 Series
F ea t u r e s
Features
The RMT-173 Series monitors provide the following features:
• Multi-format analog and digital audio signals
• Adjustment of the parameters for each channel
• High-quality waveform and/or vector monitoring
• Embedded SDI or stereo analog audio through speakers or
headphones
• Audio bar graph meters, up to sixteen
• Stereo analog audio line output of selected channel
• Area, safety, and center markers
• Closed captions for CVBS
• Pre-set or user-adjustable color temperature per channel
• Time code for SD/HD-SDI in ANC-packet form and D-VITC for
SD-SDI
• Dynamic OSD/IMD tally
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
7
RM T - 1 73 Se r ie s
F r o nt P a n el F e a t u r e s
Front Panel Features
The following feature descriptions refer to Figure 1–3 below.
Figure 1–3
RMT-173 Front Panel (PIP Layout)
Status - Sub
LED Tally
Status - Main
Audio Level Meters
Vertical (Bot Left)
Buttons
• Status: The status is displayed in the upper left corner for the main
window and in the upper right corner for the sub-window. It
includes the input channel number and signal format. Operation is
defined in the DISPLAY menu.
• Level Meters: Displays up to 16 channels, in horizontal or vertical
orientation. Define the meters setup in the AUDIO SOURCE and
METER DISPLAY menu options.
8 21 10 0 :
8
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RMT-173 Series
F r o n t P a n el F ea t u r e s
• IMD: The 16 characters of the in-monitor display (IMD) can be
displayed in red, green, yellow, or white. OSD CONFIG IMD
DISPLAY, IMD COLOR, and IMD CHAR define the static operation.
The IMD menu defines the dynamic IMD and OSD tally operations.
• Timecode: The display format for the timecode is HH: MM: SS: FF.
In the event no timecode is available, the monitor will display
--:--:--:--. Time code is currently available for SD/HD-SDI ANCpacketized and D-VITC for SD-SDI.
• Input: Pressing this button displays the Source menu. Further
presses cycle through available main video inputs. Alternately the
Up/Dn keys can be used.
• F1 through F5: These buttons serve as programmable hot keys.
Pressing a Function key displays the Function menu. Pressing the
key again toggles the state of that function. Refer to the Function
Key Menu on page 25 for details.
• Menu: Pressing this button displays the on-screen display (OSD)
Menu. Press MENU again to revert one menu level or exit out of
MENU mode.
• Up and Down: After pressing the MENU button, press Up or
Down to move within submenus.
• ENTER: After pressing the MENU button, pressing this button
selects the current menu or menu option. Changes are previewed,
but not saved, until you press the ENTER button again.
When the OSD Menu is not displayed, you can press the ENTER
button to quickly adjust the following parameters.
•
VOLUME :
Adjusts the volume from 0 to 30.
•
BRIGHTNESS:
•
CONTRAST:
•
CHROMA:
Adjusts the video brightness from 0 to 100,
where 50 is the typical value.
Adjusts the image contrast from 0 to 100, where
50 is the typical value.
Adjusts the color saturation from 0 to 100, where
50 is the typical value.
• Power LED: Lights red in standby mode and green when on. When
no main input signal is present, it blinks green.
• POWER (front): Toggles the monitor to on or standby mode.
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
9
RM T - 1 73 Se r ie s
F r o nt P a n el F e a t u r e s
• PBP Function: In PIP or PBP screen modes, the SUB window
displays the second video input, as defined in the Config Menu on
page 22 or the Function Key Menu on page 25.
Figure 1–4
RMT-173 PBP Layout
Audio Level Meters - Horizontal (Top)
Waveform and
Vector displays
Main Video
IMD
Sub Video
• Waveform/Vector: Waveform and Vector displays are controlled
by settings in the Display Menu on page 21 and by the WIN
SELECT function described in the Function Key Menu on page 25.
8 21 10 0 :
10
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RMT-173 Series
R e a r P a n el F ea t u r e s
Rear Panel Features
Figure 1–5
RMT-173 Complete Rear Panel
Figure 1–6
RMT-173 Rear Panel - Lower Right
• DC IN (jack): Accepts power plug from the included 12 VDC
power adapter.
• Power (Rocker Switch): Turns power to the monitor on (1) or off
(0).
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
11
RM T - 1 73 Se r ie s
Re a r Pa n e l F e a t u r es
Figure 1–7
RMT-173 Rear Panel - Upper Left
SDI Video Inputs (2 BNC) and SDI Outputs (2 BNC): These inputs
and outputs receive and regenerate the 3G/HD/SD-SDI signals.
HDMI IN: Type A HDMI jack accepts non-DHCP HDMI signals in
standard broadcast video formats, It can also accept similar DVI-D
resolutions with an adaptor (not supplied).
Ethernet (RJ-45): Network interface for upgrades and dynamic tally/
UMD.
8 21 10 0 :
12
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RMT-173 Series
R e a r P a n el F ea t u r e s
Figure 1–8
RMT-173 Rear Panel - Lower Left
• Line 1 Input and Output (2 BNC): CVBS composite analog video.
• Line 2 Inputs and Outputs: CVBS/Y (2 BNC), Pb/C (2 BNC),
Pr (2 BNC), analog composite, S-video, and component video.
• Audio Inputs (4 RCA) and Outputs (2 RCA): Each input pair
(one for each channel) accepts standard analog audio. Output is
from last (video) channel selected as heard from the speakers/
headphones.
• Headphones: This 1/8” jack receives a standard mini-headphone
plug and provides stereo audio. Inserting a plug here, wired or not,
will mute the speakers.
• GPI (RJ-45): Tally input. Refer to Figure 1–9 on page 14 and Table
1–1 on page 14 for connection details. Refer to the GPI Menu on
page 26 for selectable functions.
• RS485 Ports (2 RJ-45): Input and output connectors for external
control. Refer to Figure 1–9 on page 14 and Table 1–2 on page 14 for
connection details.
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
13
RM T - 1 73 Se r ie s
Re a r Pa n e l F e a t u r es
Table 1–1
GPI Pin Out
Pin
1
2
3
4
5
6
7
8
Figure 1–9
Function
GPI 1
GPI 2
GPI 3
GPI 4
GPI 5
GPI 6
NC
GND
RJ45 Connector Pin Map
.
Table 1–2
Pin
1, 2
3
4
5
6
7, 8
8 21 10 0 :
14
RS485 Pin Out
RS485 In Terminal Signal
GND
TxRx+
RxTx+
NC
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RS485 Out Terminal
Signal
GND
TxRx+
RxTx+
NC
RMT-173 Series
U s i ng t h e M e n u S y s t e m
Using the Menu System
Configuring the RMT-173 Series monitors is accomplished in the Menu
system . Each of the menus is explained on this and the following
pages.
1.
Press the MENU button to display the menu.
2.
Use the Up and Down buttons to navigate through the submenus.
The submenus are:
•
STATUS MENU (Read-only)
•
INPUT SELECT MENU
•
MARKER MENU
•
AUDIO MENU
•
DISPLAY MENU
•
CLOSED CAPTION MENU
•
CONFIG MENU
•
COLOR TEMP MENU
•
FUNCTION KEY MENU
•
GPI MENU
•
IMD MENU
•
KEY INHIBIT MENU
3.
Press the ENTER button to move into the parameter selections in
the chosen sub-menu.
4.
Use the Up or Down buttons to cycle through the sub-menus and
sub-menu selections.
5.
When the desired option is highlighted, press the ENTER button to
select it.
6.
Use the Up or Down buttons to adjust the parameter value up or
down, make a selection, or turn a function on or off.
7.
Press the ENTER button to save the parameter change and return
to the sub-menu level.
Press the MENU button to back out of a parameter or sub-menu. Press
the MENU button again to remove the menu from the screen.
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
15
RM T - 1 73 Se r ie s
U s in g t h e M en u S y s t e m
Status Menu
Note that none of the options displayed on the STATUS menu are
editable.
Table 1–3
Status Menu
Parameters
Default
Value
Domain Range
INPUT (Main)
FORMAT
COLOR TEMP
SCAN MODE
FAST MODE
MODEL
Display only; Non-selectable. The values vary
depending on input signal type and
configuration settings.
SERIAL NUMBER
IP ADDRESS
COLOR VERSION
Input Select Menu
Table 1–4
Input Select Menu
Parameters
Default Value
Domain Range
SDI1
ON
ON/OFF
SDI2
ON
ON/OFF
LINE1
ON
ON/OFF
• CVBS
LINE2
LINE2(YPBPR)
• LINE2(Y/C)
• LINE2(YPBR)
• OFF
HDMI
ON
NTSC SETUP
7.5
NTSC PHASE
0
8 21 10 0 :
16
ON/OFF
• 0
•
7.5
-50 to +50
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
Setting an input to
OFF disables it in
the source popup
menu, so that
INPUT button
presses will
bypass it.
•
RMT-173 Series
U s i ng t h e M e n u S y s t e m
Marker Menu
Important:
MARKER is disabled when SCAN mode is NATIVE, or when the input signal is
DVI or VGA.
Table 1–5
Marker Menu
Parameters
MARKER
Default
Value
OFF
Domain Range
All markers ON (enabled) or OFF
(disabled)
Select the area marker aspect ratio
to be displayed. Note: the aspect
ratio of the current image will not
appear in this list.
• OFF: turns area marker off
• 4:3
AREA MARKER
OFF
• 16:9
• 15:9
• 14:9
• 13:9
• 16:9
• 1.85:1
• 2.35:1
CENTER MARKER
OFF
ON (enabled) or OFF (disabled)
Setting the picture safe area size
marker proportional to the aspect
ratio (determined by the Area
Marker setting):
SAFETY MARKER
OFF
•
OFF
•
80%
•
85%
• 88%
• 90%
• 93%
•
95%
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
17
RM T - 1 73 Se r ie s
U s in g t h e M en u S y s t e m
Table 1–5
Marker Menu (Continued)
Default
Value
Parameters
Domain Range
Sets the luminance (white level or
brightness) to display safety, center,
and area marker line, where:
MARKER LEVEL
1
• 1 = 100%
• 2 = 75%
• 3 = 50%
Sets the area marker matte
transparency, where:
MARKER MAT
OFF
• OFF = Normal background, use
line for area marker edge only
• HALF = 50% Background
brightness
CROSS HATCH
8 21 10 0 :
18
OFF
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
• BLACK = Black
• ON enables a 10H x 8V grid for
MAIN image in full screen and
PIP modes.
RMT-173 Series
U s i ng t h e M e n u S y s t e m
Audio Menu
The menu sets up the audio sources for each channel according to the
last video input selected. Speakers and the analog Audio Output follow
the selection accordingly.
Table 1–6
Parameters
Audio Menu
Default
Value
Domain Range
Used to select the audio source
type, where:
• UNDEF = Disables audio source
AUDIO SOURCE
EBD
• AUDIO1 / AUDIO2 = Analog
audio Inputs IN1 or IN2
selected
• EBD = Embedded audio (only
for HDMI and SDI inputs)
Select embedded audio for the left
speaker/headphone/line output:
SPEAK OUT L
EBD CH1
• OFF
• CH1 thru CH16
Select embedded audio for the right
speaker/headphone/line output:
SPEAK OUT R
EBD CH1
• OFF
• CH1 thru CH16
AUDIO METER
ON
ON / OFF
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
19
RM T - 1 73 Se r ie s
U s in g t h e M en u S y s t e m
Table 1–6
Audio Menu (Continued)
Parameters
Default
Value
Domain Range
Select the audio meters to display:
• OFF
• CH1-2
• G1 (Group 1: 4 channels: 1-4)
• G2 (Group 2: 4 channels: 5-8)
• G3 (Group 3: 4 channels: 9-12)
• G4 (Group 4: 4 channels: 13-16)
• G1+G2 (Groups 1 & 2: 8
channels: 1-8)
METER SELECT
G1-4
• G1+G3 (Groups 1 & 3: 8
channels: 1-4, 9-12)
• G1+G4 (Groups 1 & 4: 8
channels: 1-8, 13-16)
• G2+G3 (Groups 2 & 3: 8
channels: 5-12)
• G2+G4 (Groups 3 & 4: 8
channels: 5-8, 13-16)
• G3+G4 (Groups 3 & 4: 8
channels: 9-16)
• G1-4 (Groups 1 - 4: 16 channels:
1-16)
HORIZ: divided evenly between
METER
DIRECTION
METER POSITION
VERTICAL
BOT LEFT
METER DIS MODE MODE 1
8 21 10 0 :
20
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
the left and right sides of the
monitor
VERT: displayed in a single bank
TOP (HORIZ)
BOT (HORIZ)
TOP LEFT (VERT)
BOT LEFT (VERT)
BOT RIGHT (VERT)
TOP RIGHT (VERT)
MODE 1: BARS ONLY
MODE 2: # & BOX
MODE 3: #, BOX, & VALUE TEXT
RMT-173 Series
U s i ng t h e M e n u S y s t e m
Table 1–6
Audio Menu (Continued)
Default
Value
Parameters
-20dB
REF LEVEL
-10dB
OVER LEVEL
Domain Range
Select the reference level:
-20dB or -18dB
Select the overload level:
•
-10dB
•
-8dB
•
-6dB
•
-4dB
•
-2dB
Display Menu
Table 1–7
Display Menu
Default
Value
Parameters
Domain Range
STATUS DISPLAY
OFF
OFF/AUTO/ON
AFD DISPLAY
OFF
OFF/ON
• OFF
WAVEFORM TYPE
VECT100
•
LINE WAVE
•
WAVEFORM
•
VECT75
•
VECT100
•
MODE 1 (WF + VECT - 75)
•
MODE 2 (WF + VECT - 100)
LINE WAVE
OFF
LINE WAVE
NUMBER
MID
SCREEN
OFF/ON
• 0 TO HIGHEST SCAN LINE
NUMBER
WAVE OVER
LIMIT
75
50 to 100
WAVE UNDER
LIMIT
5
0 to 50
WFM TRANS
OPAQUE
•
OPAQUE
•
TRANS 1
•
TRANS 2
•
TRANS 3
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
21
RM T - 1 73 Se r ie s
U s in g t h e M en u S y s t e m
Table 1–7
Display Menu (Continued)
Default
Value
Parameters
WFM POS
LEFT
TIMECODE
OFF
Domain Range
•
LEFT
•
•
RIGHT
VITC
•
LTC
•
D-VITC
•
OFF
Closed Caption Menu
Table 1–8
Parameters
Closed Caption Menu
Default
Value
CLOSED CAPTION CC1
SDI CC LOG
ON
Domain Range
•
CC1
•
CC2
•
CC3
•
CC4
•
TEXT1
•
TEXT2
•
TEXT3
•
TEXT4
•
OFF
ON/OFF
Config Menu
Table 1–9
Parameters
8 21 10 0 :
22
Config Menu
Default
Value
FAST MODE
OFF
FILM MODE
DETECT
OFF
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
Domain Range
•
OFF
•
•
ON
OFF
•
ON
RMT-173 Series
U s i ng t h e M e n u S y s t e m
Table 1–9
Config Menu (Continued)
Default
Value
Parameters
Domain Range
SUB IN TYPE
OFF
OFF/PBP/PIP
SUB IN SELECT
SDI1
INPUTS
PIP SIZE
SMALL
• SMALL/LARGE
PIP POSITION
•
•
BOT RIGHT •
•
BACKLIGHT
15
0 to 30
AUTO STANDBY
OFF
ON/OFF
APERTURE
0
0 to 24
LOCK NUMBER
---
8 characters (factory setup)
• ENGLISH
LANGUAGE
ENGLISH
•
TOP RIGHT
TOP LEFT
BOT RIGHT
BOT LEFT
CHINESE
Color Temp Menu
Important:
To make custom modifications to the RGB gains and bias, COLOR TEMP must be
set to either USER 1. or USER 2.
Table 1–10
Parameters
Color Temp Menu
Default
Value
Domain Range
Selects the color temperature (white
balance) in degrees Kelvin X 100:
COLOR TEMP
D65
•
D93 = 9300K
•
D65 = 6500K
•
D56 = 5600K
•
D50 = 5000K
•
D32 = 3200K
• USER1 (Set for HDMI and
Component Inputs)
•
RED GAIN
GREEN GAIN
BLUE GAIN
Presets
Factory
Calibrated
USER2 (Set by user)
0 to 255
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
23
RM T - 1 73 Se r ie s
U s in g t h e M en u S y s t e m
Table 1–10
Parameters
RED BIAS
GREEN BIAS
BLUE BIAS
COPY FROM
RESET
8 21 10 0 :
24
Color Temp Menu (Continued)
Default
Value
Presets
Factory
Calibrated
Domain Range
0 to 63
When USER1 or USER 2 is selected,
COPY FROM will copy one of the
--standard color temperatures to be
custom modified.
Resets User gain and bias to their factory
defaults.
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RMT-173 Series
U s i ng t h e M e n u S y s t e m
Function Key Menu
This menu lets you customize what you need each function key to do.
Table 1–11
Parameters
F1 BUTTON
Function Key Menu
Default
Value
AUDIO
METER
Domain Range
Select the function to assign to the
function button:
• SCAN: Enables or disables
display.
• NATIVE
F2 BUTTON
NATIVE
• ASPECT: Toggles between 4:3
and 16:9 scaling (SD only).
• BLUE ONLY
• MONO
F3 BUTTON
ASPECT
•
MARKER
• H/V DELAY
• AUDIO METER
F4 BUTTON
F5 BUTTON
BLUE ONLY
PBP
•
FAST MODE
•
TC
•
IMD
•
MUTE
•
PBP
•
CC
•
FREEZE
•
WIN SELECT
• UNDEF (none)
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
25
RM T - 1 73 Se r ie s
U s in g t h e M en u S y s t e m
GPI Menu
Table 1–12
Parameters
GPI 1
GPI 2
GPI 3
GPI 4
GPI 5
GPI 6
8 21 10 0 :
26
GPI Menu
Default
Value
TALLY
GREEN
TALLY RED
NATIVE
BLUE ONLY
MONO
H/V DELAY
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
Domain Range
Select the function that each GPI
will control.
•
AREA MARKER
•
CENTER MARKER
•
SAFETY MARKER
•
ASPECT
•
NATIVE
•
OVER SCAN
•
UNDER SCAN
•
BLUE ONLY
•
MONO
•
H DELAY
•
V DELAY
•
H/V
•
SDI 1
•
SDI 2
•
LINE 1
•
LINE 2
•
HDMI
•
LED TALLY GREEN
•
LED TALLY RED
•
UNDEF (NONE)
RMT-173 Series
U s i ng t h e M e n u S y s t e m
IMD Menu
Table 1–13
IMD Menu
Default
Value
Parameters
IMD DISPLAY
ON
Domain Range
ON = Displays
OFF = Does not display
Select the color in which to display
the IMD text:
• RED
IMD COLOR
RED
• GREEN
• YELLOW
• WHITE
The IMD text can contain up to 16
characters including all letters,
numbers, and some symbols.
Select the IMD protocol you want
to use:
IMD CHARACTER
IMD PROTOCOL
LOCAL
•
LOCAL
•
TSL3.1
•
TSL4.0
•
TSL5.0
•
IMAGE VIDEO
•
NETWORK
IMD ID
0
Select the IMD ID:
0 through 255
IMD NAME (S/N)
XXXXXXXX
XXXXXXXX
The IMD serial number contains up
to 16 characters.
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
27
RM T - 1 73 Se r ie s
U s in g t h e M en u S y s t e m
Table 1–13
IMD Menu
Parameters
Default
Value
Domain Range
Select the communications baud
rate:
BAUD RATE
9600
•
2400
•
4800
• 9600
• 19200
• 38400
• 57600
• 115200
LED TALLY
ON
ON/OFF
Select the OSD tally mode:
• RG: Red/Green
OSD TALLY MODE
RG
• GR: Green/Red
• RGY: Red/Green/Yellow
• OFF: No OSD Tally
Select the IMD tally mode:
• T1
• T2
• T1T2
IMD TALLY MODE
T1
• T2T1
• T1• T2• T1T2• T2T1Select the LED/OSD tally source.
Refer to Table 1–2 and Figure 1–9
on page 14:
TALLY SOURCE
STANDARD • STANDARD
• IMAGE VIDEO
• TSL
8 21 10 0 :
28
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RMT-173 Series
S p e c if ic a t io n s
Key Inhibit Menu
Key Inhibit Menu
Table 1–14
Parameters
Key Inhibit Menu
Default
Value
Domain Range
• OFF = Does not inhibit keys
KEY INHIBIT
OFF
• ON = Inhibits all keys except
POWER and MENU (to make
setup changes)
Specifications
The general specifications of the RMT-173 Series monitors are listed in
Table 1–15 below.
Table 1–15
RMT-173 Specifications
Specification
Dimensions,
including the table stand
Dimensions,
with rack mount
Shipping Weight
LCD Dimension
Aspect Ratio
Resolution
Color Depth
Viewing Angle
Brightness
Contrast Ratio
RMT-173
12.5” H x 16.5” W x 6.3” D
305 mm H x 420 mm W x 160 mm
D
10.3” H (6U) x 19” W x 2.7” D
305 mm H x 483 mm W x 70 mm
D
13 lbs. (5.9 kg)
17.3”
4:3/16:9 (native)
1920 H x 1080 V
8-bit, 16.7M colors
178° H / 178° V
300 cd/m2
600:1
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
29
RM T - 1 73 Se r ie s
Sp e ci fi ca t io n s
Table 1–16 below lists the I/O specifications.
Table 1–16
RMT-173 I/O Specifications
Specification
RMT-173 Values
• 6 BNCs: CVBS, S-Video, YPbPr, 3G/
HD/SD-SDI (supports embedded
audio)
Video Inputs
• HDMI
6 BNCs: Loop out of BNC In
4 RCAs: Analog stereo for EXT sources
2 RCAs: Analog stereo (monitoring, same
as speakers)
Video Outputs
Audio Inputs
Audio Outputs
Table 1–17 below distinguishes each of the RMT-173 models.
Table 1–17
RMT-173 Distinctions Among Each Model
Category
3G-A SDI
SMPTE 424M
HD-SDI
SMPTE 292M,
296M
SD-SDI
SMPTE 259M
Analog
Note:
Specification
1080p: (60/59.94/50)
3G
HD
SD
A
1080p: (23.98, 24, 25,
29.97, 30)
1080i: (60/59.94/50)
1035i: (60/59.94)\
720p: (60/59.94/50)
480i: (60/59.94)
576i: (50)
PAL
NTSC
1080psF may display as the equivalent 1080i rates listed
above. Segmented-Frame (sF) scan is not supported.
Table 1–18 below lists the specifications for CVBS inputs.
Table 1–18
RMT-173 CVBS I/O Specifications
Specification
Signal Type
Signal Amplitude
Impedance
Return Loss
DC Offset
Frequency Response
8 21 10 0 :
30
RMT-173 Values
NTSC, PAL
1V peak-to-peak ±3 dB
75 Ω
> 40 dB ±5 MHz
0V ±0.05 V
±0.2 dB to 5 MHz
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
RMT-173 Series
S p e c if ic a t io n s
Table 1–18
RMT-173 CVBS I/O Specifications
Specification
Differential Gain
Differential Phase
RMT-173 Values
< 1%
< 1.5°
Table 1–19 below lists the specifications for SDI inputs.
Table 1–19
RMT-173 SDI Specifications
Specification
Signal Compliance
Connector
Impedance
Return Loss
Maximum Signal Level
Signal Amplitude
DC Offset
Overshoot
Total Jitter
Rise and Fall Time
RMT-173 Values
SMPTE 424M, SMPTE 299M, SMPTE
296M, SMPTE 274M, SMPTE 259M,
SMPTE 292M, SMPTE 291M
BNC per IEC 169-8
75 Ω
>18 dB at 5 to 270 MHz
>15 dB at 270 MHz to 1.5 GHz
>10 dB up to 3 GHz
800 mV peak-to-peak, 10%
800 mV peak-to-peak, 10%
0 V ±0.5 V
<10%
<0.2 UI
3G (3Gb/s): <135 ps
HD (1.5 Gb/s): <270 ps
SD: <700 ps
8 21 10 0:
R MT-1 73 S e r ie s U se r G u id e
© 20 13 Wo hl e r Te c hn ol og i e s , In c . A l l r ig h ts re se rv ed .
31
RM T - 1 73 Se r ie s
Te c h ni c al F un c t io n O v e r v i ew
Technical Function Overview
Figure 1–10 below illustrates the overall functionality of the RMT-173
Series monitors.
Figure 1–10
8 21 10 0 :
32
RMT-173 Block Diagram
RM T-1 73 S e r ie s U s e r G ui d e
© 2 01 3 Woh le r Te ch no lo g ie s, Inc . A ll ri g ht s re s e r v ed .
Download PDF