Model No. PFTL49610 Serial No. USER'S MANUAL Serial Number Decal QUESTIONS? If you have questions, or if there are missing parts, we will guarantee complete satisfaction through direct assistance from our factory. TO AVOID UNNECESSARY DELAYS, PLEASE CALL DIRECT TO OUR TOLL-FREE CUSTOMER HOT LINE. The trained technicians on our Customer Hot Line will provide immediate assistance, free of charge to you. CUSTOMER HOT LINE: 1-800-999-3756 Mon.–Fri., 6 a.m.–6 p.m. MST CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Visit our website at www.proform.com new products, prizes, fitness tips, and much more! TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 TROUBLE-SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover Note: An EXPLODED DRAWING is attached in the center of this manual. IMPORTANT PRECAUTIONS WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions and information before operating the treadmill. wearing only stockings, or in sandals. 1. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions. 10. When connecting the power cord (see page 7), plug the power cord into a surge suppressor (not included) and plug the surge suppressor into a grounded circuit capable of carrying 15 or more amps. No other appliance should be on the same circuit. Do not use an extension cord. 2. Use the treadmill only as described. 3. Place the treadmill on a level surface, with at least eight feet of clearance behind it and two feet on each side. Do not place the treadmill on any surface that blocks air openings. To protect the floor or carpet from damage, place a mat under the treadmill. 11. Use only a single-outlet surge suppressor that meets all of the specifications described on page 7. To purchase a surge suppressor, see your local PROFORM dealer or call 1-800-8063651 and order part number 146148. 4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near water. 12. Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury. 5. Do not operate the treadmill where aerosol products are used or where oxygen is being administered. 6. Keep children under the age of 12 and pets away from the treadmill at all times. 13. Keep the power cord and the surge suppressor away from heated surfaces. 7. The treadmill should be used only by persons weighing 250 pounds or less. 14. Never move the walking belt while the power is turned off. Do not operate the treadmill if the power cord or plug is damaged, or if the treadmill is not working properly. (See BEFORE YOU BEGIN on page 4 if the treadmill is not working properly.) 8. Never allow more than one person on the treadmill at a time. 9. Wear appropriate exercise clothing when using the treadmill. Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both men and women. Always wear athletic shoes. Never use the treadmill with bare feet, 15. Never start the treadmill while you are standing on the walking belt. Always hold the handrails while using the treadmill. 2 16. The treadmill is capable of high speeds. Adjust the speed in small increments to avoid sudden jumps in speed. 17. The pulse sensor is not a medical device. Various factors, including the user's movement, may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general. 20. When folding or moving the treadmill, make sure that the storage latch is fully closed. 21. Inspect and tighten all parts of the treadmill every three months. 22. Never drop or insert any object into any opening. 23. 18. Never leave the treadmill unattended while it is running. Always remove the key and unplug the power cord when the treadmill is not in use. 19. Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See ASSEMBLY on page 5, and HOW TO FOLD AND MOVE THE TREADMILL on page 10.) You must be able to safely lift 45 pounds (20 kg) to raise, lower, or move the treadmill. DANGER: Always unplug the power cord immediately after use, before cleaning the treadmill, and before performing the maintenance and adjustment procedures described in this manual. Never remove the motor hood unless instructed to do so by an authorized service representative. Servicing other than the procedures in this manual should be performed by an authorized service representative only. 24. This treadmill is intended for in-home use only. Do not use this treadmill in any commercial, rental, or institutional setting. WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. SAVE THESE INSTRUCTIONS The decals shown below have been placed on your treadmill. If one of the decals is missing or illegible, please call our Customer Service Department, toll-free, to order a free replacement decal (see ORDERING REPLACEMENT PARTS on the back cover of this manual). Apply the decal in the location shown. Note: This decal is shown at 38% of actual size. 3 BEFORE YOU BEGIN Thank you for selecting the revolutionary PROFORM® 50 GTS treadmill. The 50 GTS treadmill combines advanced technology with innovative design to help you get the most from your exercise program in the convenience and privacy of your home. And when you’re not exercising, the unique 50 GTS can be folded up, requiring less than half the floor space of other treadmills. at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number of the treadmill is PFTL49610. The serial number can be found on a decal attached to the treadmill (see the front cover of this manual for the location). For your benefit, read this manual carefully before using the treadmill. If you have additional questions, please call our Customer Service Department toll-free Before reading further, please review the drawing below and familiarize yourself with the labeled parts. Book Holder Water Bottle Holder (Bottle not included) Console Handrail Storage Latch Key/Clip LEFT SIDE RIGHT SIDE Walking Belt Circuit Breaker Foot Rail Front Wheel Power Cord Cushioned Walking Platform Rear Roller Adjustment Bolts 4 ASSEMBLY Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not dispose of the packing materials until assembly is completed. Refer to the drawings below to identify the parts used in assembly. Assembly requires the following tools: The included allen wrench and your own phillips screwdriver , mallet wire cutters and needle-nose pliers . Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner. Whe Handrail Bolt (78)–2 Screw (101)–4 Long Screw (79)–4 Short Handrail Bolt (89)–2 1. With the help of a second person, carefully raise the Uprights (82) until the treadmill is in the position shown. Small Handrail Washer (29)–2 Washer (36)–2 H 1 Insert one of the Extension Legs (103) into the treadmill as shown. Make sure that the Thick Base Pad (97) is on the indicated side. Note: It may be helpful to tip the Uprights (82) in the direction shown by the arrow as you insert the Extension Leg. To fully insert the Extension Leg, it may be necessary to tap it with a mallet. 82 Insert the other Extension Leg (103) in the same way. 82 2. Refer to drawing 2a. If there is a plastic tie in the Cage Nut (109) in the Right Handrail (85), remove the plastic tie. Pull 5 to 6” of the Wire Harness (26) out of the Right Upright (82). Route the Wire Harness through the bracket on the Right Handrail and out of the indicated hole. If necessary, use needle-nose pliers to grip the connectors on the Wire Harness. Thread the included wire tie through the indicated hole in the Right Handrail (85). 97 2a 2c 23 103 26 85 Refer to drawing 2b. Look into the Right Handrail (85) and make sure that the Wire Harness (26) has been secured to the side shown. Tighten the wire tie and cut off the excess from the end. Refer to drawing 2c. Make sure the Handrail Inserts (102) are in the Handrails (23, 85). Insert the bracket on the Right Handrail (85) into the upper end of the right Upright (82), with the lower end of the Right Handrail on the Extension Leg (103). Tighten a Short Handrail Bolt (89) with a Small Handrail Washer (29) into the upper end of the Upright. Attach the Left Handrail (23) as described above. Note: There is not a wire in the left Upright (82). 5 26 89 29 Tie 109 82 85 82 2b 82 Tie 85 26 103 102 3. With the help of a second person, carefully tip the Uprights (82) down as shown. Align the lower ends of the Handrails (23, 85) with the holes in the Extension Legs (103). (Note: If you cannot align the holes, remove the Handrail Inserts  [see drawing 3a]). Tighten a Handrail Bolt (78) with a Washer (36) through each Extension Leg into each Handrail. Attach each Extension Leg with two Screws (101) and a Base Pad (52) as shown. Make sure that the Extension Legs are fully inserted into the Uprights (82), and push down on the Uprights as you tighten the Screws. Tighten the Handrail Bolts (78). Note: One replacement Base Pad (52) and Spacer (not shown) may be included. If a Base Pad becomes worn and needs to be replaced, use the replacement Base Pad. If a Thick Base Pad (97) needs to be replaced, use the replacement Base Pad with the Spacer. With the help of a second person, carefully tip the Uprights (82) back to the upright position. 3 97 82 52 101 85 36 82 52 23 103 78 97 103 36 78 97 4a 85 4. Place the Console Base (87) on the Handrails (85, 23). Make a loop with the indicated plastic tie and insert the two Wires (26) through the loop. Pull out only enough of the two Wires to connect them to the connectors in the Console Base. Important: Make sure that the Wires are fully inserted. If the connectors do not fit together easily, rotate them and then connect them. Tighten the loop and cut off the excess tie. WARNING: Do not disconnect or connect the Wires while the treadmill power cord is plugged in. 87 26 Tie 4b 87 85 23 79 Refer to drawing 4b. Thread four Long Screws (79) into the Handrails (85, 23) and the Console Base (6). After all four Long Screws have been started, tighten the Screws until they are snug; do not overtighten the Screws. 5. Remove the Lock Knob (105) from the Lock Pin (11). Make sure that the Lock Pin Collar (14) and the Spring (56) are on the Lock Pin as shown. Insert the Lock Pin into the Latch Bracket (77). 79 5 105 Tighten the Lock Knob (105) onto the Lock Pin (11). 77 56 14 11 6. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor, place a mat under the treadmill. 6 OPERATION AND ADJUSTMENT THE PERFORMANT LUBETM WALKING BELT plug. Plug the power cord into a surge suppressor, and plug the surge suppressor into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Important: The treadmill is not compatible with GFCI-equipped outlets. Your treadmill features a walking belt coated with PERFORMANT LUBETM, a high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that looks like the adapter illustrated in drawing 2 may be used to connect the surge suppressor to a 2-pole receptacle as shown in drawing 2 if a properly grounded outlet is not available. HOW TO PLUG IN THE POWER CORD DANGER: Improper connection of the equipment-grounding conductor can result in an increased risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product—if it will not fit the outlet, have a proper outlet installed by a qualified electrician. 1 Grounded Outlet Box Surge Suppressor Grounding Pin Your treadmill, like any other type of sophisticated electronic equipment, can be seriously damaged by sudden voltage changes in your home’s power. Voltage surges, spikes, and noise interference can result from weather conditions or from other appliances being turned on or off. To decrease the possibility of your treadmill being damaged, always use a surge suppressor with your treadmill (see drawing 1 at the right). To purchase a surge suppressor, see your local PROFORM dealer or call 1-800806-3651 and order part number 146148. Grounding Pin Grounded Outlet Grounding Plug 2 Grounded Outlet Box Adapter Use only a single-outlet surge suppressor that is UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a UL suppressed voltage rating of 400 volts or less and a minimum surge dissipation of 450 joules. The surge suppressor must be electrically rated for 120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to use a properly functioning surge suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury. Surge Suppressor Lug Metal Screw The temporary adapter should be used only until a properly grounded outlet (drawing 1) can be installed by a qualified electrician. The green-colored rigid ear, lug, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used it must be held in place by a metal screw. Some 2-pole receptacle outlet box covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is grounded before using an adapter. This product must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment-grounding conductor and a grounding 7 CONSOLE DIAGRAM LED Track Incline Control Note: If there is a thin sheet of clear plastic on the face of the console, remove it. Displays Speed Control Clip Key right. Insert the batteries into the battery compartment, making sure that the negative (–) ends of the batteries are touching the springs in the battery compartment. CAUTION: Before operating the console, read the following precautions. Close the battery cover, push up on the battery cover tab, and then push the tab forward as shown in the inset drawing. Be sure that the tab locks into place. • Do not stand on the walking belt when turning on the power. • Always wear the clip (see the drawing at the lower right) while using the treadmill. When the key is removed from the console, the walking belt will stop. STEP-BY-STEP CONSOLE OPERATION Before operating the console, make sure that the power cord is properly plugged in. (See HOW TO PLUG IN THE POWER CORD on page 7.) • Adjust the speed in small increments. • The training zones marked above the speed control are general guidelines only. See page 14 for more information. Stand on the foot rails of the Clip treadmill. Find the clip attached to the key and slide the clip onto the waistband of your clothing. Next, insert the key into the console. Test the clip by carefully taking a few steps backward until the key is pulled from the console. If the key is not pulled from the console, adjust the position of the clip as needed. • To reduce the possibility of electric shock, keep the console dry. Avoid spilling liquids on the console and use only a sealable water bottle. BATTERY INSTALLATION Follow the steps below to operate the console. The console requires three "AA" batteries (not included). Alkaline batteries are recommended. Open the battery cover as shown in the drawing at the upper 1 Insert the key fully into the power switch. Inserting the key will not turn on the displays. The displays will turn on when the ON/RESET button is pressed or when the walking belt is started. Note: If you just installed batteries, the displays will already be on. Battery Cover Tab Batteries 8 2 SPEED display—This display shows the speed of the walking belt, in miles per hour. Reset the speed control. Slide the speed control to the RESET position. Note: Each time the walking belt is stopped, the speed control must be moved to the RESET position before the walking belt can be restarted. 3 To reset the displays at any time, press the ON/RESET button. Start the walking belt. After you have moved the speed control to the RESET position, slowly slide it to the right until the walking belt begins to move at slow speed. Carefully step onto the walking belt and begin exercising. Change the speed of the walking belt as desired by sliding the speed control. 6 To measure your Pulse Sensor heart rate, stand on the foot rails and place your thumb on the pulse sensor as shown. The pulse sensor is pressure activated—fully press it down. Do not press too hard, or the circulation in your thumb will be restricted, and your pulse will not be detected. Next, raise your thumb slightly until the heart-shaped indicator in the heart rate display flashes steadily. Hold your thumb at this level. After a few seconds, three dashes will appear in the display and then your heart rate will be shown. Hold your thumb on the sensor for another 15 seconds for the most accurate reading. If the displayed heart rate appears to be too high or too low, or if your heart rate is not displayed, lift your thumb off the sensor and allow the display to reset. Press down again on the sensor as described above. To stop the walking belt, step onto the foot rails and slide the speed control to the RESET position. Note: During the first few minutes that the treadmill is used, inspect the alignment of the walking belt and align it if necessary (see page 13). 4 Adjust the incline of the treadmill as desired. To change the incline of the treadmill, press the top or bottom of the incline control until the desired incline level is reached. 5 Measure your heart rate, if desired. Follow your progress with the LED track and the three displays. The LED Track—The LED track represents a distance of 1/4 mile. As you exercise, the indicators around the track will light one at a time until you have completed 1/4 mile. A new lap will then begin. Make sure that your thumb is positioned as shown, and that you are applying the proper amount of pressure to the pulse sensor. Try the sensor several times until you become familiar with it. Remember to stand still while measuring your heart rate. 7 TIME/DISTANCE display—This display shows the elapsed time and the distance that you have walked or run, in miles. When you are finished exercising, stop the walking belt and remove the key. Step onto the foot rails, stop the walking belt. Adjust the incline of the treadmill to the lowest level. The incline must be at the lowest level when the treadmill is raised to the storage position. Remove the key from the console. The displays will turn off about five minutes after the key is removed. Note: To conserve the batteries, the displays will automatically turn off any time that the walking belt is stopped and the ON/RESET button is not pressed for five minutes. CALS/FAT CALS Arrow display—This display shows the approximate numbers of calories and fat calories you have burned. (See FAT BURNING on page 14.) Every seven seconds, the display will change from one number to the other. Arrows in the display will indicate which number is currently shown. 9 HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE 1 Before folding the treadmill, adjust the incline to the lowest position. If this is not done, the treadmill may be permanently damaged. Next, unplug the power cord. CAUTION: You must be able to safely lift 45 pounds (20 kg) in order to raise, lower, or move the treadmill. 1. Hold the treadmill with your hands in the locations shown at the right. CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your back. Raise the treadmill about halfway to the vertical position. 2. Move your right hand to the position shown and hold the treadmill firmly. Hold the lock knob with your left hand 2 and pull it to the side. Raise the treadmill until the lock knob is aligned with the slot in the catch. Note: You may need to push the handrail to the side. Slowly release the knob. Make sure that the pin on the lock knob is inside the slot. Slot To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit. Knob HOW TO MOVE THE TREADMILL Before moving the treadmill, convert the treadmill to the storage position as described above. Make sure that the pin on the lock knob is inserted into the slot in the catch. 1. Hold the handrails as shown and place one foot against a wheel. Do not hold or push on the book holder or the book holder may be damaged. Book Holder 2. Tilt the treadmill back until it rolls freely on the front wheels. Carefully move the treadmill to the desired location. Never move the treadmill without tipping it back. To reduce the risk of injury, use extreme caution while moving the treadmill. Do not attempt to move the treadmill over an uneven surface. 3. Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position. Base Front Wheels 10 HOW TO LOWER THE TREADMILL FOR USE 1. Hold the upper end of the treadmill with your right hand as shown. Using your left hand, pull the storage latch and hold it. Pivot the treadmill until the frame and foot rail are past the storage latch. If necessary, press the handrail to the left. 1 Slot Knob 2. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. Do not drop the treadmill frame to the floor. To decrease the possibility of injury, bend your legs and keep your back straight. 11 2 TROUBLE-SHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet (see page 7). Use only a single-outlet surge suppressor that meets all of the specifications described on page 7. Important: The treadmill is not compatible with GFCI-equipped outlets. b. After the power cord has been plugged in, make sure that the key is fully inserted into the console. c. Check the circuit breaker located on the treadmill near the power cord. If the switch protrudes as shown, the circuit breaker has tripped. To reset the circuit breaker, wait for five minutes and then press the switch back in. c Tripped Reset Tripped Reset PROBLEM: The power turns off during use SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in. b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in. c. Make sure that the two wires under the console are fully plugged in. (Refer to assembly step 4 on page 6. WARNING: Do not disconnect or connect the wires while the treadmill power cord is plugged in.) d. Remove the key from the console. Reinsert the key fully into the console. e. If the treadmill still will not run, please call our Customer Service Department, toll-free. PROBLEM: The displays of the console do not function properly SOLUTION: a. Remove the key from the console and unplug the power cord. Remove the screws from the hood and carefully remove the hood. Locate the Reed Switch (21) and the Magnet (43) on the left side of the Pulley (42). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Reed Switch Screw (76) and move the Reed Switch slightly. Retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading. 12 a 1/8” 76 21 Top View 42 43 PROBLEM: The pulse display on the console does not function properly SOLUTION: a. Wash your hands prior to using the pulse sensor. Clean the sensor with a damp cloth and mild detergent. PROBLEM: The incline will not work SOLUTION: a. Make sure that the two wires under the console are fully plugged in. (Refer to assembly step 4 on page 6. WARNING: Do not disconnect or connect the wires while the treadmill power cord is plugged in.) PROBLEM: The walking belt slows when walked on SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 7. b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller adjustment bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is properly tightened. b 3”–4” Rear Roller Adjustment Bolts c. If the walking belt still slows when walked on, call our Customer Service Department, toll-free. PROBLEM: The walking belt is off-center or slips when walked on SOLUTION: a. If the walking belt has shifted to the left, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn the left rear roller bolt clockwise 1/2 of a turn. Be careful not to overtighten the walking belt. If the walking belt has shifted to the right, turn the left rear roller bolt counterclockwise 1/2 of a turn. Plug in the power cord, insert the key and run the treadmill for a few minutes. Repeat until the walking belt is centered. a b. If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the allen wrench, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side of the walking belt 3 to 4 inches off the walking platform. Be careful to keep the walking belt centered. Plug in the power cord, insert the key and carefully walk on the treadmill for a few minutes. Repeat until the walking belt is properly tightened. b 13 CONDITIONING GUIDELINES WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems. The pulse sensor is not a medical device. Various factors, including your movement, may affect the accuracy of heart rate readings. The sensor is intended only as an exercise aid in determining heart rate trends in general. The following guidelines will help you to plan your exercise program. Remember—these are general guidelines only. For more detailed exercise information, obtain a reputable book or consult your physician. EXERCISE INTENSITY Whether your goal is to burn fat or to strengthen your cardiovascular system, the key to achieving the desired results is to exercise with the proper intensity. The proper intensity level can be found by using your heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise. To find the proper heart rate for you, first find your age near the bottom of the chart (ages are rounded off to the nearest ten years). Next, find the three numbers above your age. The three numbers define your “training zone.” The lower two numbers are recommended heart rates for fat burning; the higher number is the recommended heart rate for aerobic exercise. To measure your heart rate during exercise, use the pulse sensor on the console. If your heart rate is too high or too low, adjust the speed and incline of the treadmill. Fat Burning To burn fat effectively, you must exercise at a relatively low intensity level for a sustained period of time. During the first few minutes of exercise, your body uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body begin to use stored fat calories for energy. If your goal is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in your training zone. For maximum fat burning, adjust the speed and incline of the treadmill until your heart rate is near the middle number in your training zone. Aerobic Exercise If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise is activity that requires large amounts of oxygen for prolonged periods of time. This increases the demand on the heart to pump blood to the muscles, and on the lungs to oxygenate the blood. For aerobic exercise, adjust the speed and incline of the treadmill until your heart rate is near the highest number in your training zone. WORKOUT GUIDELINES Each workout should include the following three parts: A Warm-up—Start each workout with 5 to 10 minutes of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise. Training Zone Exercise—After warming up, increase the intensity of your exercise until your pulse is in your training zone for 20 to 60 minutes. (During the first few weeks of your exercise program, do not keep your pulse in your training zone for longer than 20 minutes.) Breathe regularly and deeply as you exercise—never hold your breath. A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the flexibility of your muscles and will help prevent post-exercise problems. EXERCISE FREQUENCY To maintain or improve your condition, complete three workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key to success is to make exercise a regular and enjoyable part of your everyday life. 14 PART LIST—Model No. PFTL49610 R0902A To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual. Key No. Qty. 1 2 3 4* 1 1 4 1 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30* 31 32 33 34 35 36 37 38 39 2 2 1 1 1 1 1 1 1 1 8 16 1 2 1 2 1 1 1 1 1 1 1 1 2 1 1 2 1 1 1 2 1 4 2 Description Motor Belt Pulley/Flywheel/Fan Motor Nut Motor/Pulley/ Flywheel/ Fan Incline Motor Bolt Incline Motor Spacer Incline Motor Stop Bracket Small Nut Belly Pan Spacer Lock Pin Frame Pin Clip Lock Pin Collar Incline Motor Nut Electronic Screw Rear Foot Spacer Rubber Hood Bracket Front Hood Bracket Warning Decal Reed Switch Reed Switch Clip Left Handrail Controller Electronics Bracket Circuit Breaker Power Cord Power Cord Grommet Small Handrail Washer Latch Assembly Incline Frame Frame Pivot Bolt Motor Tension Washer Tension Bushing Front Roller Adj. Bolt Handrail Washer Motor Tension Nut Motor Bolt Cap Screw Key No. Qty. 40 1 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 2 1 1 4 4 4 13 1 2 1 1 2 4 4 1 1 1 2 2 4 1 1 1 1 2 1 1 4 2 1 1 5 1 1 2 6 77 1 Description Left/Right Foot Rail Cap Foot Rail Front Roller/Pulley Magnet Platform Screw Isolator Isolator Screw Belly Pan Fastener Shield Belt Guide Battery Cover Front Belly Pan Base Pad Cable Tie Clamp Cable Tie Walking Belt Spring Rear Roller Rear Isolator Rear Foot Rear Foot Screw Ground Wire Hood Bracket Plate Belly Pan Rear Endcap Rear Roller Adj. Bolt Motor Latch Decal Rear Platform Screw Latch Catch Screw Latch Catch Walking Platform 8” Cable Tie Interface Bracket Motor Tension Bolt Foot Rail Insert Reed Switch Screw/ Belly Pan Screw Storage Latch Bracket 15 Key No. Qty. 78 79 80 81 82 83 84 2 4 1 4 1 2 2 85 86 87 88* 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 # # # 1 2 1 1 2 1 1 2 1 1 2 1 4 1 1 1 18 2 2 2 1 1 1 1 2 1 1 1 Description Handrail Bolt Long Screw Wire Cover Motor Star Washer Upright Incline Leg Pivot Bolt Incline Leg Pivot Washer Right Handrail Wheel Bolt Console Base Console Assembly Short Handrail Bolt Key/Clip Incline Motor Belly Pan Roller Adj. Washer Book Holder Motor Hood Front Wheel Incline Motor Shield Thick Base Pad Trim Guard Upright Grommet Allen Wrench Screw Handrail Insert Extension Leg Extension Leg Cap Lock Knob Choke Incline Control Speed Control Cage Nut 8” White Wire, Pigtail 8” Green Wire, 2 Ring User's Manual * Includes all parts shown in the box # These parts are not illustrated 65 92 65 92 58 12 60 59 47 68 64 69 70 67 45 49 63 68 44 62 61 57 46 75 58 60 59 17 9 47 39 45 41 55 46 71 1 To identify the parts shown on this exploded drawing, refer to the PART LIST on page 15 of the USER’S MANUAL. 44 40 3 47 44 32 2 43 54 46 33 4* 42 66 37 41 45 22 53 16 47 44 75 39 21 76 16 3 40 49 62 18 76 EXPLODED DRAWING—Model No. PFTL49610 9 10 16 38 6 46 106 15 5 15 7 15 45 16 8 81 5 13 19 76 48 33 34 15 R0902A 35 74 33 16 24 51 32 15 16 16 31 73 18 25 16 76 26 73 28 27 76 76 104 101 97 103 102 23 78 36 20 109 76 105 72 79 77 104 101 52 82 14 56 29 97 11 97 101 103 102 101 83 13 89 84 85 78 36 20 86 109 30* 15 26 62 96 16 95 79 99 26 101 52 29 89 84 100 86 97 95 101 15 EXPLODED DRAWING—Model No. PFTL49610 83 101 76 87 50 76 93 91 107 16 108 R0902A 76 76 80 88* 94 98 90 76 16 16 16 ORDERING REPLACEMENT PARTS To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give the following information: • The MODEL NUMBER OF THE PRODUCT (PFTL49610) • The NAME OF THE PRODUCT (PROFORM® 50 GTS treadmill) • The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual) • The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the EXPLODED DRAWING and PART LIST attached in the center of this manual). PROFORM is a registered trademark of ICON Health & Fitness, Inc. LIMITED WARRANTY ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used for commercial or rental purposes; or products used as store display models. No other warranty beyond that specifically set forth above is authorized by ICON. ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you. The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you. This warranty gives you specific legal rights. You may also have other rights which vary from state to state. ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813 Part No. 176083 R0902A Printed in USA © 2002 ICON Health & Fitness, Inc.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project