Psion Teklogix | Vehicle-Mount Computer 8580 G2 | Batteries - IngenuityWorking

WorkAbout Pro G2 – Workabout Pro 2
Accessory Catalog
WorkAbout Pro G2
WorkAbout Pro 3
2
Table of Contents
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
„
Batteries
Battery Doors
Cables and Adapters
Carrying Devices and Covering Accessories
Chargers and Docking Stations
Power Supplies and Accessories
Vehicle Mounts and Cradles
Vehicle Cradle Accessories
End-Caps
Radio Options – WLAN
Radio Options – WWAN
RFID Options
Linear Scanners
1D Imagers
2D Imagers
Software Options
Miscellaneous
3
Batteries
Part No: 1050494 Model No: WA3006
Part No: 1050192-002 Model No: WA3010
Part No: 1050944 Model No: None
High Capacity (3300 mAh) Lithium Ion Rechargeable Battery
The High Capacity Lithium Ion Rechargeable Battery pack provides 3300
mAh of capacity at 3.7 volts. The 3300 mAh battery offers approximately
22% more power than the 2350 mAh battery which makes it ideal for
solutions that deploy high-speed WWAN and WLAN radios, data capture
devices and other peripherals. The 3000 mAh battery is an Advanced
Smart Battery that has a power indicator so that the battery’s state of
charge is always known. A high capacity battery door is required with the
High Capacity Battery.
Super High Capacity (4400 mAh) Lithium Ion Rechargeable Battery
The Super High Capacity Lithium Ion Rechargeable Battery pack
provides 4400 mAh of capacity at 3.7 volts. The 4400 mAh battery is an
Advanced Smart Battery that has a power indicator so that the battery’s
state of charge is always known. A super high capacity battery door is
required with the Super High Capacity Battery.
Backup battery for Workabout Pro G2 and Workabout Pro 3
Battery shift life: In order to establish a benchmark, we run the same battery run down test on every new hand held device. Every 12 seconds we scan a 1D barcode via laser scanner, and transmit the
barcode data over 802.11g, repeat until battery is depleted. This test simulates a scan-intensive environment, not allowing the device to suspend, shutdown, or take advantage of any power saving. The
WAP C G1 lasts 8 hours, 23 minutes with a 3300 mAh battery pack in this test. The WAP C G2 lasts 7 hours, 2 minutes in this test. Since the WAP G2 is using a faster processor, larger memory, and
includes 2 additional LED’s for display backlighting, it is logical that using the same battery pack (3300 mAh) results in less battery shift life when compared to the WAP G1. The 4400 mAh battery pack
delivers 9 hours, 33 minutes in this test. WAP S G1 and WAP S G2 versions deliver approximately 20 minutes more in these test scenarios.
4
Battery Doors
High Capacity (3300 mAh) Battery Doors
Super High Capacity (4400 mAh) Battery Doors
Part No: 1050917-002, Model No: WA3016-G2
Part No: 1050919-001, Model No: WA3018-G2
For Workabout Pro G2 3 S (numeric) and
Workabout Pro 3 S (numeric) and Q (Querty)
versions
For Workabout Pro G2 3 S (numeric) and
Workabout Pro 3 S (numeric) and Q (Querty)
versions
Part No: 1050916-001, Model No: WA3015-G2
Part No: 1050918-001, Model No: WA3017-G2
For Workabout pro G2 and 3 C (full alpha) version
For Workabout pro G2 and 3 C (full alpha) version
5
Cables and Adapters
Serial USB to RS232 Converter Cable
Connects to WA4002, WA4002-G1, and WA4003-G2
desktop docking stations to provide RS232
connectivity.
Part No: N/A, Model No: WA4015-G1
USB to Ethernet Adapter
Connects to WA4002, WA4002-G1, and WA4003-G2
desktop docking stations to provide 10/100bT ethernet
support.
Part No: N/A, Model No: WA4010-G1
Cable, Tether Serial USB to RS232 converter
This Tether Serial USB to RS232 Adapter provides
RS232 connectivity to the WORKABOUT PRO through
the tether port on the bottom of the handheld unit.
Part No: 1050077, Model No: WA4020-G2
6
Cables and Adapters (cont’d)
Tether Cable
Cable, Connector Tether (with fly wire)
Part No: 1030223, Model No: WA1050
Part No: 1050552, Model No: WA1002
Part No:N/A, Model No: WA4001-G2
Part No: 1030315, Model No: CA2900
Tether Cable Open-Ended - 6FT with strain
Part No: N/A, Model No: CA2950-G1
Tether to USB A Cable
Enables users to connect USB A terminated devices
(such as printers, scanners, GPS module) to the
WORKABOUT PRO, 3 point tether connector improves
strength and stability when connected to the device.
Tether to USB B for Active Sync
This cable allows a user to connect a WAP G2 or 3 to a
laptop or desktop for Activesync without requiring a
docking station. It’s important to note that the WAP is
not charged through this USB cable. We recommend the
PS1050-G2 for charging, which is the AC power adapter
used on the G1 and G2 desktop docking station – comes
with power connections for worldwide use, and plugs into
the DC power jack on the base of the WAP G2.or 3.
Includes USB cable.
7
Cables and Adapters (cont’d)
Cable, Tether to Ethernet Adapter
Part No: N/A, Model No: WA4025
Vehicle Cradle USB Cable Adapter
Enables users to connect USB A and USB B
terminated devices directly to the Vehicle Cradle's
DB15 pin connector without using the Port Replicator.
Part No: 1050551, Model No: WA1001
Powered Vehicle Cradle Cable
Promark power extension, DC, 6', waterproof with 10A
fuse & choke
Part No: N/A, Model No: CA1210
8
Carrying Devices and Covering Accessories
Handstrap - double loop, with stylus for Workabout Pro G2/C C
Part No: N/A, Model No: WA6025
Handstrap - double loop, w/o stylus for Workabout Pro G2/3 C
Part No: N/A, Model No: WA6026
Part No: N/A, Model No: 6091
Handstrap - double loop, with stylus for Workabout Pro G2 S
or WAP 3 S/Q
Part No: N/A, Model No: WA6125
Handstrap - double loop, w/o stylus for Workabout Pro G2 S
or WAP 3 S/Q
Part No: N/A, Model No: WA6126
Nylon Pouch (C,S, Q)
The nylon pouch is an ideal accessory for carrying the
WORKABOUT PRO when using it without the pistol grip.
It will work with each of the C, S or Q models. The pouch
comes with a metal swivel and belt loop. Because the
WORKABOUT PRO is inserted into the pouch facing
upright, the pouch will not interfere with the PC card end
cap.Pouch (Nylon C,S, Q)
9
Carrying Devices and Covering Accessories
Part No: N/A, Model No: WA6197-G2
Part No: N/A, Model No: WA6097-G2
Part No: 30585, Model No: N/A
Protective Carrying Case Universal Endcap, Open
Ended for Workabout Pro G2 S or Workabout Pro 3 S/Q
The case does not interfere with scanning and can be used
with or without the scanner attached. It can also be used
with either the pistol grip and non-pistol grip units, as well as
with the hand strap. Removing the hand held is easily done
through a “trap door” on the back of the case. This case is
also compatible with the standard shoulder strap (P/N
30585), however, only the belt loop is included.
Protective Carrying Case Universal Endcap, Open
Ended for Workabout Pro G2/3 C
The case does not interfere with scanning and can be
used with or without the scanner attached. It can also
be used with both the pistol grip and non-pistol grip
units. Removing the handheld is easily done through a
“trap door” on the back of the case. This case is also
compatible with the standard shoulder strap (P/N
30585), however, only the belt loop is included.
Shoulder Strap for Protective Carry Cases (C,S, Q)
The 6-foot shoulder strap with pad allows a user to hang
the terminal, in the protective case, over their shoulder.
Hanging the terminal facilitates unimpaired operator
movement. The shoulder strap attaches to metal clips on
the protective case.
10
Carrying Devices and Covering Accessories
Soft-Shell Holster
This convenient and easy to use soft-shell holster
with removable belt and swivel holster pad can be
used to hang a WORKABOUT PRO with a pistol grip
securely from the waist.
Part No: 1030227, Model No: WA6050
Pistol Grip
The WORKABOUT PRO pistol grip attachment allows users
to convert the WORKABOUT PRO to a convenient pistol grip
unit. This WORKABOUT PRO pistol grip works with the
WA9000-G1, WA9003-G1, and WA9005-G1 and it
is compatible with G1, G2 and 3 models. The pistol grip
comes with 4 screws and a printed instruction sheet.
(Instructions are also available electronically).
Part No: 1050460-001, Model No: WA6101-G1
Pistol Grip
The WORKABOUT PRO pistol grip attachment allows
users to convert the WORKABOUT PRO to a
convenient pistol grip unit. This WORKABOUT PRO
pistol grip works with the WA9212-G1 slim pod 2D
imager. The pistol grip comes with 4 screws and a
printed instruction sheet. (Instructions are also available
electronically).
Part No: 1050459-001, Model No: WA6102-G1
Part No: N/A, Model No: WA6103
Flush Mount Pistol Grip
The WORKABOUT PRO pistol grip attachment allows
users to convert the WORKABOUT PRO to a
convenient pistol grip unit.
11
Carrying Devices and Covering Accessories
Rubber Boots
For:
Part No: N/A, Model No: WA6400
Part No: N/A, Model No: WA6401
Auto Range
Endcap
Part No: N/A, Model No: WA6402
Part No: N/A, Model No: WA6403
1D/2D Endcap
Part No: N/A, Model No: WA6404
Workabout Pro G2 S or
Workabout Pro 3 S/Q
Workabout Pro G2/3 C
GSM/WiFi
Endcap
Part No: N/A, Model No: WA6405
12
Chargers and Docking Stations
Desktop Docking Station with AC Adapter & Lead
The Desktop Docking Stating supports all C and S and Q
variants of WORKABOUT PRO G1, G2 and 3 devices and
allows a WORKABOUT PRO M/C to be charged while
simultaneously providing USB Host and Client functions.
The Host USB port allows peripherals such as a printer, a
keyboard, or a mouse to be connected while the Client USB
port allows connectivity of the Docking Station to a PC.
An additional spare battery charge well is integrated into the
Desktop Docking Station to ensure that your spare batteries
remain fully charged and that your WORKABOUT PRO
remains ready to perform. Charging internal batteries of the
terminal takes approximately 3-5 hours depending on the
battery type (3300 mAh or 4400 mAh).
Part No: N/A, Model No: WA4003-G2
The Desktop Docking Station is equipped with a single dualcoloured LED indicator to provide easy to read charge
status. This docking station can consume up to 3A @
120VAC or 1.5A @ 240VAC.
Note: An optional ethernet expansion module (WA4010-G1)
converts docking station from USB to Ethernet.
13
Chargers and Docking Stations (cont’d)
Part No: N/A, Model No: WA4204-G2
Part No:N/A, Model No: WA4304-G2
Part No: 9008693, Model No: N/A
Quad Docking Station c/w UPS (no lead)
The 4 unit Multi-Dock allows up to four
WORKABOUT PRO C units to be charged
simultaneously while providing 10/100 BaseT
Ethernet communications in excess of 2Mbps. This
version of the 4 unit Multi-Dock is compatible with
7525M-E, 7525C-G1,7527C-G2 and 7527-3. It also
provides sufficient power to fast charge the batteries
in the unit. Charging internal batteries of the terminal
takes approximately 2-4 hours depending on the
battery type. This docking station can consume up to
3A @ 120V AC or 1.5A @ 240V AC. A power lead is
not included but can be ordered separately to suit the
customer’s region (p/n 9008693 for North America).
Quad Docking Station c/w UPS (no lead)
The 4 unit Multi-Dock allows up to four WORKABOUT
PRO S or Q units to be charged simultaneously while
providing 10/100 BaseT Ethernet communications in
excess of 2Mbps. This version of the 4 unit Multi-Dock is
compatible with 7525S-G1, 7527S-G2 and 7527-3. It
also provides sufficient power to fast charge the batteries
in the unit. Charging internal batteries of the terminal
takes approximately 2-4 hours depending on the battery
type. This docking station can consume up to 3A @
120V AC or 1.5A @ 240V AC. A power lead is not
included but can be ordered separately to suit the
customer’s region (p/n 9008693 for North America).
14
Chargers and Docking Stations (cont’d)
Part No: 1080221, Model No: WA3001-G1
Single Battery Charger
The Single Battery Charger charges standard or High
Capacity batteries one at a time. An appropriate
power lead should be ordered at the time of
purchase. (Universal Power Supply comes with the
lead.)
Power Supply and Lead for Single Unit Charger North America – AC, 5V/2A
Part No: 1080220, Model No: CA1067
Quad Battery Charger
The Quad Battery Charger is capable of charging four
batteries at once and can charge either Standard or
High Capacity batteries. It comes with a Universal
Power Supply. An appropriate power lead should be
ordered at the time of purchase.
Part No: 1080220, Model No: WA3004-G1
Power Lead for Quad Unit Charger - North America
Part No: 9008693, Model No: N/A
15
Power Supply And Accessories
Universal Power Supply
The universal power supply is used to provide DC
power to the desktop docking station (WA4003-G2)
from an AC source or to provide power directly to the
Workabout Pro G2 handheld (plugs into DC power
jack on base of unit). A power lead is included.
Part No: 9001904, Model No: PS1050-G1
Automotive Power Supply
Cigarette lighter adapter connects directly to DC jack on
base of Workabout Pro G2 handheld Includes
automotive adapter and tether cable.
The automotive adapter fits any standard 12VDC car
cigarette receptacle.
Part No: 1050463-001, Model No: WA3113-G2
Power Pre-Regulator (15-55V) SINO
The DC/DC power pre-regulator provides power to the
WORKABOUT PRO from any vehicle providing 1555VDC input voltage.
Part No: 19893-600, Model No: PS1300
16
Vehicle Mounts and Cradles
Part No: 1080880-001, Model No: WA1210-G2
Part No: 1080881-001, Model No: WA1310-G2
Part No: N/A, Model No: CA1210
Powered Vehicle Cradle 12V (C)
The Powered Vehicle Cradle is a highly ruggedized, single unit station
dock. The Powered Vehicle Cradle is designed to allow the
WORKABOUT PRO to be powered by a vehicle battery. The battery
installed in the WORKABOUT PRO is also recharged by the vehicle
battery. This option accepts DC power sources over the range 9V to
20V. Although it provides quick insertion and removal, the cradle holds
the WORKABOUT PRO C securely even when operated in high vibration
environments. This vehicle cradle is compatible with the RAM B 101
mount (WA4006) that can be adjusted three-dimensionally to give
maximum display readability and device usability in any vehicle. A port
replicator option (WA4005-G1) is available.
Powered Vehicle Cradle 12V (S/Q)
The Powered Vehicle Cradle is a highly ruggedized, single unit station
dock. The Powered Vehicle Cradle is designed to allow the WORKABOUT
PRO to be powered by a vehicle battery. The battery installed in the
WORKABOUT PRO is also recharged by the vehicle battery. This option
accepts DC power sources over the range 9V to 20V. Although it provides
quick insertion and removal, the cradle holds the WORKABOUT PRO S or
Q securely even when operated in high vibration environments. This
vehicle cradle is compatible with the RAM B 101 mount (WA4006) that can
be adjusted three-dimensionally to give maximum display readability and
device usability in any vehicle. A port replicator option (WA4005-G1) is
available.
Powered Vehicle Cradle Cable
Promark power extension, DC, 6', waterproof with 10A fuse & choke
17
Vehicle Cradle Accessories
Part No: N/A, Model No: WA4006
RAM B 101 Mount
This extremely rugged, heavy-duty universal mounting system
with 1” ball joints, allow the Vehicle Cradle to be mounted in any
vehicle providing easy access to the WORKABOUT PRO. This
universal mounting system has locking joints and allows attached
terminals to be adjusted three-dimensionally giving maximum
display readability and device usability.
Vehicle Cradle USB Cable Adapter
Enables users to connect USB A and USB B terminated
devices directly to the Vehicle Cradle's DB15 pin connector
without using the Port Replicator.
Part No: 1050551, Model No: WA1001
Part No: 1080224, Model No: WA4005-G1
Port Replicator
The Port Replicator is an optional accessory that allows peripherals
(e.g. printers or weigh scales) to be attached to the powered Vehicle
Cradles for the WORKABOUT PRO. The Port Replicator supports as
many as three serial devices and a USB Host when connected to the
WORKABOUT PRO through a Vehicle Cradle. The Port Replicator
has 4 peripheral ports:
- One USB 1.1 Client port to connect to a powered Host such as a
Notebook
- Three, 9-pin, RS232 serial ports
USB and serial cables are not provided with the Port Replicator
Serial devices may require a separate power supply.
18
End-caps
3-Port Serial End-Cap (Kit)
The 3-Port Serial End-Cap provides IrDA, RS232,
and TTL connectivity in a convenient location at the
top of the WORKABOUT PRO.
Part No: N/A, Model No: BR1000-G1
End-Cap (Standard)
This replacement part is for a standard End-Cap suitable
for all WORKABOUT PRO models.
Part No: 1050006, Model No: WA6209
End-Cap (Multi Purpose) without GSM Shroud
This replacement part is for a multi purpose End-Cap
(MPEC) suitable for all WORKABOUT PRO models.
Part No: 1004212-001, Model No: N/A
19
End-caps (cont’d)
GPS End-Cap
GPS module housed inside MPEC with GSM Shroud
End-Cap
Part No:1051350, Model No: N/A
GPS End-Cap
GPS module housed inside MPEC without GSM
Shroud
Part No: 1051355, Model No: N/A
20
Radio Options – WLAN
802.11b/g Direct Sequence (DS)-Extended Range Radio (CCXCertified)
This 802.11b/g WLAN radio (also known as WiFi Radio) is provided in a
user installable standard Compact Flash (CF) card format. This radio
form factor enables users to add a WLAN radio to their device as
required without returning it to the depot or having to buy a new device.
The radio kit comes with the CF Card Radio, the mechanical stop, and
the screws that are required to secure the radio in place.
Part No: N/A, Model No: RA2041
802.11 a/b/g Radio
This 802.11 a/b/g WLAN radio (also known as WiFi Radio) is provided
in a user installable standard Compact Flash (CF) card format. This
radio form factor enables users to add a WLAN radio to their device as
required without returning it to the depot or having to buy a new
device. The radio kit comes with the CF Card Radio, the mechanical
stop, and the screws that are required to secure the radio in place.
NOTE: only available for CE 5.0 units
Part No:N/A, Model No: RA2043
21
Radio Options – WWAN
Part No: N/A, Model No: RA3030-G2
Part No:N/A, Model No: RA3040-G2
GSM/GPRS/EDGE xMod Radio (c/w CF Mech Stop, End-Cap)
The GSM/GPRS/EDGE Quad-band module is a GSM radio expansionmodule mounted on a user installable daughter board that interfaces
easily with the 100-Pin connector located inside the WORKABOUT PRO
accessed through the back cover plate. The expansion module
accommodates a GSM/GPRS/EDGE Quad-band radio and a SIM card.
The GSM/GPRS/EDGE kit includes the expansion board with
GSM/GPRS Radio, GSM endcap, and mechanical stop. Supports data
and voice. Compatible with G2 and 3 units only. WiFi compatible.
UMTS HC25 Radio Kit
The UMTS module is a radio expansion-module mounted on a user
installable daughter board that interfaces easily with the 100-Pin
connector located inside the WORKABOUT PRO accessed through the
back cover plate. The expansion module accommodates a UMTS radio
and a SIM card. The UMTS kit includes the expansion board with the
UMTS Radio, endcap, and mechanical stop. Supports data and
voice. Compatible with G2 and 3 units only. WiFi compatible.
22
RFID Options
Part No: 1100625, Model No: UHF-CA3-AC5-G2
Part No: 1051585, Model No: UHF-CA3-A1-G2
UHF Passive Multi Regional RFID Reader – Circular Antenna
The UHF-CA3-A5-G2 is an Impinj, Indy R1000 chipset, UHF passive
reader solution which delivers superior performance, standards-based
compatibility (EPC GEN2 compliant, ISO 18000-6C) in a unique compact
form factor. Thanks to the ability to programmatically set the operating
frequency, the reader most noticeable feature is its ability to operate in
the U.S. (FCC part 15), European (ETSI EN 302 208), and IC (Canadian)
regulatory environments. Other attractive product features are the RF
programmable power settings (0 to 500 mW) and the future integration
with the BizTalk RFID platform. Reader uses 100 pin interface while the
circular antenna is housed inside a pod located on the back of the
handheld. Product comes as a kit and will work with GPRS (RA-3030).
The GPRS component must be purchased separately. For additional
compatibility information please refer to the RFID Product Guide.
UHF Passive Multi Regional RFID Reader – Linear Antenna
The UHF-CA3-A1-G2 is an Impinj, Indy R1000 chipset, UHF passive
reader solution which delivers superior performance, standards-based
compatibility (EPC GEN2 compliant, ISO 18000-6C) in a unique compact
form factor. Thanks to the ability to programmatically set the operating
frequency, the reader most noticeable feature is its ability to operate in
the U.S. (FCC part 15), European (ETSI EN 302 208), and IC (Canadian)
regulatory environments. Other attractive product features are the RF
programmable power settings (0 to 500 mW) and the future integration
with the BizTalk RFID platform. Reader uses 100 pin interface while the
linear antenna is housed inside multi purpose end-cap located at the top
of the unit. Product comes as a kit and will not work with GPRS (end-cap
antenna is available without GSM shroud only) For additional
compatibility information please refer to the RFID Product Guide.
23
RFID Options
HID USB HF Multi ISO (15693 & 14443 & NFC) RFID Kit
Multi ISO, multi protocol High Frequency (13.56 MHz) RFID
reader with integrated horizontal antenna. Reader housed
inside multi purpose end-cap and is available with GSM
antenna shroud only (p/n 1051270). Uses USB interface.
Part No: 1051270, Model No: HF-AM1-G2
HID XMOD HF Multi ISO (15693 & 14443 & NFC) RFID Kit
Multi ISO, multi protocol High Frequency (13.56 MHz) RFID
reader with integrated horizontal antenna. Reader uses 100
pin interface while antenna is housed inside multi purpose
end-cap. Model available without GSM antenna shroud only
(p/n 1009096). Uses 100 pin interface.
Part No: 1009096, Model No: HF-AM1-A2
24
RFID Options (cont’d)
Tagys USB HF (ISO 15693 & 18000-3) RFID Kit
Multi protocol High Frequency (13.56 MHz) RFID
reader with integrated horizontal antenna. Reader
housed inside multi purpose end-cap and is available
with GSM antenna shroud only (p/n 1051310). Uses
USB interface.
Part No: 1051310, Model No: HF-T2-G2
Tagsys XMOD HF (ISO 15693 & 18000-3) RFID Kit
Multi protocol High Frequency (13.56 MHz) RFID reader
with integrated horizontal antenna. Reader uses 100 pin
interface while antenna is housed inside multi purpose
end-cap. Model available without GSM antenna shroud
only (p/n 1054320. Uses 100 pin interface.
Part No: 1004320, Model No: HF-T2-G2X
Part No: 1004310, Model No: HF-T2-A3-G2
Tagsys HF RFID (ISO 15693 & 18000-3) Paddle for
Workabout Pro G2
Rugged industrial design specifically for harsh
environments, this RFID reader provides new ‘track and
trace’ options for warehouse or logistics operations.
Whether it is stacks of plastic crates, pallets, or other
valuable assets, a simple wave of the arm instantly
registers the RFID tag data. Connects to the Workabout
Pro G2 via the tether port.
25
RFID Options (cont’d)
HID USB LF (ISO 11784 & 11785) RFID Kit
Multi protocol Low Frequency (125 & 134.2 KHz)
RFID reader with integrated horizontal antenna.
Reader housed inside multi purpose end-cap and is
available with GSM antenna shroud only (p/n
1051330). Uses USB interface.
Part No: 1051330, Model No: LF-AH1-G2
Part No: 1009098, Model No: LF-AH1-A1
HID XMOD LF (ISO 11784 & 11785) RFID Kit
Multi protocol Low Frequency (125 & 134.2 KHz) RFID
reader with integrated horizontal antenna. Reader uses
100 pin interface while antenna is housed inside multi
purpose end-cap. Model available without GSM antenna
shroud only (p/n 1009098). Uses 100 pin interface.
26
RFID Options (cont’d)
Agrident LF (ISO 11784 & 11785) RFID Kit
Integrated Low Frequency (134.2 KHz) reader offers
convenient data collection for industrial and animal
tracking applications, with the flexibility and mobility of a
rugged portable Windows CE or Windows Workabout
Pro G2. HDX and FDX-B compliant to ISO 11784/5 plus
EM4x02 compatible. Uses the 100 pin interface and the
endcap.
Part No:1003762, Model No: AIR200
Agrident LF RFID Telescopic Antenna
It is the right choice if a flexible length antenna is
required e.g. for a more convenient transportation.
Attached to the back of the Workabout Pro the AEA121
Low Frequency (134.2 KHz) antenna supports the onehand reading concept and is the right solution when the
long reading distance shall not reduce your mobility.
Connects to the AIR200.
Note: Will not work with any pod scanners.
Part No: L9000349, Model No: AEA121
27
Linear Scanners
Part No: N/A, Model No: WA9000-G1
Part No: N/A, Model No: WA9002-G1
1D xMod Laser Scanner SE1223 High Performance, POD Format
The SE1223 High Performance Scanner Module provides the highest
performance in 1D bar code scanning. Only adding an additional 75g of
weight to the WORKABOUT PRO, this scanner module ensures that users
of the handheld computer can still maintain comfortable one-handed use
for an entire shift without muscle fatigue. The scanner module integrates
seamlessly into the back of the WORKABOUT PRO with six screws and
can be installed with ease. The SE1223 High Performance Scanner
Module supports the following Symbologies: UPC/EAN, Code 128, Code
39, Code 93, I 2 of 5, Discrete 2 of 5, Codabar, MSI UCC/EAN 128, and
TriOptic Code 39. An optional Pistol Grip (WA6101-G1) is also available for
use with the SE1223 HP module to allow users to convert the
WORKABOUT PRO to a convenient pistol grip unit.
1D xMod Laser Scanner SE955, Slim POD Format
The SE955 Scanner Module provides the smallest and lightest scan engine
available while still offering high performance in 1D bar code scanning. The
SE955 features the unique “Adaptive Logic Technology” that enables
damaged or poorly printed bar codes to be read. The ultra slim SE955
Scanner Module adds just 32g of weight and is integrated onto the back of
the WORKABOUT PRO, ensuring that the unit is still light and ergonomic.
This scanning module has a working range of up to 88.9cm (35in.) and
supports the following Symbologies: UPC/EAN, Code 128, Code 39, Code
93, I 2 of 5, Discrete 2 of 5, Codabar, and MSI Plessey.
28
Linear Scanners (cont’d)
Part No: N/A, Model No: WA9005-G1
1D xMod Laser Scanner SE1223 LR, POD Format
The SE1223 Long Range Scanner Module provides high performance and
long range 1D bar code scanning. This scanning module reads bar codes up
to 6.1 meters (20 feet) away. Only adding an additional 75g of weight to the
WORKABOUT PRO, this scanner module ensures that users of the
handheld computer can still maintain comfortable one-handed use for an
entire shift without muscle fatigue. The scanner module integrates
seamlessly into the back of the WORKABOUT PRO with six screws and can
be installed with ease. The SE1223 LR Scanner Module supports the
following Symbologies: UPC/EAN, Code 128, Code 39, Code 93, I 2 of 5,
Discrete 2 of 5, Codabar, MSI UCC/EAN 128, and TriOptic Code 39. An
optional Pistol Grip (WA6101-G1) is also available for use with the SE1223
LR module to allow users to convert the WORKABOUT PRO to a
convenient pistol grip unit.
1D End-Cap Laser Scanner SE955, without GSM shroud
The SE955 Scanner Module provides the smallest and lightest scan engine
available while still offering high performance in 1D bar code scanning. The
SE955 features the unique “Adaptive Logic Technology” that enables
damaged or poorly printed bar codes to be read. This scanning module has
a working range of up to 88.9cm (35in.) and supports the following
Symbologies: UPC/EAN, Code 128, Code 39, Code 93, I 2 of 5, Discrete 2
of 5, Codabar, and MSI Plessey.
Part No: N/A, Model No: WA9102-G1
29
Linear Scanners (cont’d)
1D End-Cap Laser Scanner SE955, with GSM shroud
The SE955 Scanner Module provides the smallest and lightest
scan engine available while still offering high performance in 1D
bar code scanning. The SE955 features the unique “Adaptive
Logic Technology” that enables damaged or poorly printed bar
codes to be read. This scanning module has a working range of
up to 88.9cm (35in.) and supports the following Symbologies:
UPC/EAN, Code 128, Code 39, Code 93, I 2 of 5, Discrete 2 of
5, Codabar, and MSI Plessey.
Part No: N/A, Model No: WA9112-G1
1D End-Cap Auto-Range Laser Scanner SE1524 ER
Scans from a range of 2 inches to 45 feet. The SE1524ER uses
state-of-the-art optical technology and fuzzy logic capability,
providing reliability, durability and ease of use. Designed for the
easy targeting and capture of bar codes at great distances —
such as in multi-level warehouse environments — this scan
engine has the widest working range in the industry.
Part No: N/A, Model No: WA9009-G1
30
1D Imagers
Part No: N/A, Model No: WA9003-G1
Part No: N/A, Model No: WA9103-G1
1D EV15 Imager, POD Format
This integrated 1D imager provides exceptional scanning performance and
great reliability at a fraction of the cost of a standard laser bar code scanner.
This imager has a quicker scan rate (270 scans per second) compared to
that of laser bar code scanners which translates to enhanced decoding of
degraded bar codes. The imager is also able to decipher bar codes in a full
range of lighting conditions from total darkness to complete sunlight.
Furthermore, because the imager does not have any moving parts, it
consumes less power than a standard bar code scanner thus providing the
WORKABOUT PRO with a longer battery life and offers a much longer
MTBF (Mean Time Between Failure). The 1D imager supports UPC (E&A),
EAN, Code 11, Code 39, Code 128, UCC EAN 128, ISBN, ISBT,
Interleaved, Matrix, Industrial and Standard 2 of 5, Codabar, Code 93, MSI,
Plessey, and Telepen symbologies. This 1D imager module integrates
seamlessly onto the back of the handheld unit and can be installed with
ease. Compatible with G1 and G2. Also compatible with pistol grip
(WA6101-G1).
1D EV15 End-Cap Imager, without GSM shroud
This integrated 1D imager provides exceptional scanning performance and
great reliability at a fraction of the cost of a standard laser bar code
scanner. This imager has a quicker scan rate (270 scans per second)
compared to that of laser bar code scanners which translates to enhanced
decoding of degraded bar codes. The imager is also able to decipher bar
codes in a full range of lighting conditions from total darkness to complete
sunlight.
31
1D Imagers (cont’d)
1D EV15 End-Cap Imager, with GSM shroud
This integrated 1D imager provides exceptional scanning
performance and great reliability at a fraction of the cost of a standard
laser bar code scanner. This imager has a quicker scan rate (270
scans per second) compared to that of laser bar code scanners which
translates to enhanced decoding of degraded bar codes. The imager
is also able to decipher bar codes in a full range of lighting conditions
from total darkness to complete sunlight.
Part No: N/A, Model No: WA9113-G1
32
2D Imagers
End-Cap 2D Imager, without GSM shroud
HHP5180 2D end-cap imager.
Part No: N/A, Model No: WA8010-G1
2D Slim Pod SX5400 Imager
SX5400 2D slim pod imager. Compatible with G2 only. Also compatible
with WA6102-G1 pistol grip.
Part No: N/A, Model No: WA9008
2D Slim Pod HHP 5180 Imager
Compatible with pistol grip WA6102-G1 as well as with G1 and
G2.
Part No: N/A, Model No: WA9212-G1
33
Software Options
MCC (Mobile Control Center)
Device management software to help manage the
mobile device fleet. Monitor device status, run activity
reports, install and update software. Plus
troubleshooting, configuration, security and back-up.
Part No: N/A, Model No: SW2600
Wavelink Avalanche
Integrates with Psion Teklogix devices for centralized,
rapid, hands-off updates to mobile data terminals
anywhere in the enterprise. Slashes IT admin costs and
greatly improves ROI.
Part No: N/A, Model No: 310-LI-AV*
Naurtech
We’ve partnered with Naurtech to develop the CETerm
Smart Client for Psion Teklogix mobile computers.
Feature-rich application interface lets you develop data
collection solutions via terminal emulations or the web
browser.
Part No: N/A, Model No: SW2100
34
Software Options (cont’d)
OpenTek Term
A powerful terminal-emulation application ideal for real-time data
transaction apps associated with mainframes and servers. Supports
ANSI and TESS emulation, and comes with a raft of features to help
configuration and improve emulation session performance.
Part No: N/A, Model No: S3010
Win TekTerm
Win TekTerm is a similar emulation client designed to run on Windows
desktop-like computers, like the 8580/8590 vehicle mount computers.
Total Recall
Protects your apps, device configuration, and data. Features an
easy-to-use profile manager and automatic back-up and restore
capability. Plus automatic profile restoration after a cold reboot.
This utility is provided free of charge and is loaded in the OS of the
handheld.
Part No: N/A, Model No: N/A
Psion Teklogix SDK
Our open, flexible software development kit helps developers create
great mobile apps fast – then port them to any Psion Teklogix device.
The SDK is provided free of charge.
Part No: N/A, Model No: N/A
35
Software Options (cont’d)
PTX Connect
A powerful enterprise communications platform that supports push-totalk, instant messaging and email using VoIP technology – all on the
same rugged devices your people use for data capture.
Part No: N/A, Model No: SW2500
Other Software Options
Funk Odyssey Client
- p/n S2400
AirFortressTM
CE .Net Client for WORKABOUT PRO - p/n S400
RFID Demo Applications
Available for all readers listed in this catalog. Please contact your technical representative to discuss the
solution(s) which best fits your needs.
RFID SDKs
Available for all readers listed in this catalog. Please contact your technical representative to discuss the
solution(s) which best fits your needs.
36
Miscellaneous
Part No: N/A, Model No: WA9001-G1
PC Card xMod Kit (c/w CF/PC Card Mechanical Stop)
Installs onto 100 pin internal expansion connector to provide
a PCMCIA card slot.
Note: custom mechanical stop may be required for various
sizes of cards.
Stylus
This pack contains 5 replacement styluses suitable for all
WORKABOUT PRO models.
Part No: 1030394, Model No: WA6100-G1
Plate Back Cover, Standard
This replacement Back Plate Cover is suitable for all
WORKABOUT PRO models.
Part No: 1030271, Model No: WA6208
37
Miscellaneous (cont’d)
High Durability Screen Protector
These highly durable Screen Protectors help prevent your
WORKABOUT PRO G2 C or S display from unwanted
scratches. Pack of 4.
Part No: 1051110, Model No: WA6112-G2
Plastic Stylus with holder kit, tethered stylus
Part No: 1030271, Model No: WA6310-G1
38
Download PDF