MULTIQUIP DCA-60SSI2 Specifications

MULTIQUIP DCA-60SSI2 Specifications
PARTS AND OPERATION MANUAL
PARTS AND OPERATION MANUAL
© COPYRIGHT 2001, MULTIQUIP INC.
MQ POWER
DCA-60SSI2
TM
WHISPERWATT
GENERATOR
PARTS LIST NO. 8081500G
REV. #3 (09/15/01)
MULTIQUIP INC.
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
SERVICE DEPARTMENT:
310-537-3700
800-421-1244
800-835-2551
FAX: 310-537-3927
FAX: 310-638-8046
E-mail:[email protected] • www:multiquip.com
PAGE 2 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
PAR
TS DEP
AR
TMENT
ARTS
DEPAR
ARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
VICE DEP
AR
TMENT
SER
ARTMENT
SERVICE
DEPAR
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEP
AR
TMENT
DEPAR
ARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 3
TABLE OF CONTENTS
Here's How To Get Help ........................................... 3
Table Of Contents .................................................... 4
Parts Ordering Procedures ...................................... 5
Rules for Safe Operation ......................................... 6-9
Towing and Transportation ....................................... 10
Trailer Safety Guidelines .......................................... 11-17
Trailer Wiring Diagram .............................................. 18
Electric Brake Troubleshooting ................................ 19
Hydraulic Brake Troubleshooting .............................. 20
Operation Decals ..................................................... 21-22
DCA -60SSI2 Specifications ................................... 23
General Information ................................................. 24
Major Components .................................................. 55
Dimensions .............................................................. 26
Control Panel Descriptions ...................................... 28-29
Engine Operating Panel Descriptions ...................... 30-31
Output Terminal Panel Descriptions ......................... 32-33
Output Amperage Setup .......................................... 34-35
Output Voltage Setup ............................................... 36-39
Installation ............................................................... 40-41
Pre Set-up ............................................................... 42-45
Load Application ...................................................... 46
Generator Start-up Procedure ................................. 47-49
Generator Shut-down Procedure .............................. 50
Maintenance ............................................................ 52-55
Generator Wiring Diagram ........................................ 56
Engine Wiring Diagram ............................................ 57
Engine Troubleshooting ............................................ 58-59
Generator/Engine Troubleshooting ........................... 60
Explanation of Codes in Remarks Column .............. 62
Suggested Spare Parts ........................................... 63
ISUZU 6BG1 ENGINE
MQ POWER DCA-60SSI2
AC GENERATOR
Terms and Condition of Sale — Parts .................. 156
Generator Assembly ................................................ 64-65
Control Box Assembly ............................................. 66-67
Engine & Radiator Assembly ................................... 68-71
Engine Operating Panel Assembly .......................... 72-75
Battery Assembly .................................................... 76-77
Muffler Assembly .................................................... 78-79
Fuel Tank Assembly ................................................ 80-81
Enclosure Assembly ............................................... 82-85
Rubber Seal Assembly ............................................ 86-87
Name Plate And Decals .......................................... 88-89
Cylinder Head Cover Assembly ............................ 90-91
Cylinder Head Assembly ...................................... 92-93
Cylinder Block Assembly ..................................... 94-97
Oil Pan and Level Gauge Assembly ..................... 98-99
Camshaft and Valve Assembly ............................. 100-101
Crankshaft Piston and Flywheel Assembly .......... 102-103
Timing Gear and Flywheel Housing Assembly ..... 104-105
Inlet Manifold Assembly ....................................... 106-107
Exhaust Manifold Assembly ................................. 108-109
Ventilation Assembly ............................................ 110-111
Water Pump and Corrosion Resistor Assembly .... 112-113
Thermostat and Housing Assembly ..................... 114-115
Engine Water Piping Assembly ............................. 116-117
Fan and Fan Belt Assembly ................................. 118-119
Fuel Injection Assembly ....................................... 120-121
Fuel Filter and Bracket Assembly ........................ 122-123
Fuel Pump and Pipe Assembly ............................ 124-125
Oil Cooler and Oil Filter Assembly ....................... 126-127
Oil Pump and Oil Strainer Assembly .................... 128-129
Oil and Vacuum Piping Assembly ........................ 130-131
Electrical Control Assembly ................................. 132-133
Starter Components Assembly ............................ 134-135
Alternator Components Assembly ........................ 136-137
Injection Pump Components Assembly ............... 138-141
Governor Components Assembly ......................... 142-145
Feed Pump Assembly .......................................... 146-147
Misc. Injection Pump Assembly ........................... 148-149
Coupling Assembly ............................................... 150-151
Water Sedimenter Assembly ................................ 152-153
Switch and Relay Assembly ................................. 154-155
NOTE
Specification and part number
are subject to change without
notice.
PAGE 4 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
PARTS ORDERING PROCEDURES
■
■
■
■
■
■
■
Dealer account number
Dealer name and address
Shipping address (if different than billing address)
Return fax number
Applicable model number
Quantity, part number and description of each part
Specify preferred method of shipment:
•
•
•
•
UPS Ground
UPS Second Day or Third Day*
UPS Next Day*
Federal Express Priority One (please provide us with your Federal
Express account number)*
•
•
Airborne Express*
Truck or parcel post
*Normally shipped the same day the order is received, if prior to 2PM west coast time.
Earn Extra Discounts when
you order by FAX!
All parts orders which include complete part numbers
and are received by fax qualify for the following extra
discounts:
Number of
line items ordered
1-9 items
Additional Discount
3%
10+ items**
5%
Get special freight allowances
when you order 10 or more
line items via FAX!**
■ UPS Ground Service at no charge for freight
■ PS Third Day Service at one-half of actual freight cost
No other allowances on freight shipped by any other carrier.
**Common nuts, bolts and washers (all items under $1.00 list price)
do not count towards the 10+ line items.
*DISCOUNTS ARE SUBJECT TO CHANGE*
ount
c
s
i
D
Fax
Extra
c USA
i
t
s
e
m
for Do
Only
s
r
e
l
Dea
UPS l
Specia
nly
ders o
xed or
For fa
Now! Direct TOLL-FREE access
to our Parts Department!
Toll-free nationwide:
800-421-1244
Toll-free FAX:
800/6-PARTS-7 • 800-672-7877
Fax order discount and UPS special programs revised June 1, 1995
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 5
RULES FOR SAFE OPERATION
CAUTION:
Failure to follow instructions in this manual
may lead to serious injury or even death!
This equipment is to be operated by trained
and qualified personnel only! This equipment
is for industrial use only.
■ NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or generator.
The following safety guidelines should always be used when ■ High Temperatures – Allow the engine to cool before
operating the DCA-60SSI2 portable generator:
adding fuel or performing service and maintenance
GENERAL SAFETY
functions. Contact with hot components can cause serious
burns.
■ DO NOT operate or service this equipment before
reading this entire manual.
■ The engine of this generator requires an adequate free
flow of cooling air. Never operate the generator in any
■ This equipment should not be operated by
enclosed or narrow area where free flow of the air is
persons under 18 years of age.
restricted. If the air flow is restricted it will cause serious
damage to the generator or engine and may cause injury
to people. The generator engine gives off DEADLY carbon
■ NEVER operate this equipment without proper
monoxide gas.
protective clothing, shatterproof glasses, steeltoed boots and other protective devices
CAUTION:
required by the job.
■ Always refuel in a well-ventilated area,
away from sparks and open flames.
■ NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
■ NEVER operate this equipment under the
influence or drugs or alcohol.
■ NEVER use accessories or attachments, which are not
recommended by MQ Power for this equipment. Damage
to the equipment and/or injury to user may result.
■ Manufacturer does not assume responsibility for any
accident due to equipment modifications.
■ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■ Always check the machine for loosened threads or bolts
before starting.
■ Always use extreme caution when
working with flammable liquids. When
refueling, stop the engine and allow it
to cool. DO NOT smoke around or near
the machine. Fire or explosion could
result from fuel vapors, or if fuel is spilled
on a hot engine.
■
NEVER operate the generator in an
explosive atmosphere or near combustible
materials. An explosion or fire could result
causing severe bodily harm or even
death.
■
Topping-off to filler por t is
dangerous, as it tends to spill fuel.
PAGE 6 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
RULES FOR SAFE OPERATION
CAUTION:
CAUTION:
DO NOT touch or open any of the below
mentioned components while the
generator is running. Always allow
sufficient time for the engine and generator
to cool before performing maintenance.
■ NEVER touch output terminals during operation. This is
extremely dangerous. Always stop the machine when
contact with the output terminals is required.
CAUTION:
Radiator
1. Radiator Cap - Removing the radiator cap while the
engine is hot will result in high pressurized, boiling water
to gush out of the radiator, causing severe scalding to
any persons in the general area of the generator.
2. Coolant Drain Plug - Removing the coolant drain plug
while the engine is hot will result in hot coolant to gush
out of the coolant drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
■ Backfeed to a utility system can cause electrocution and/
or property damage. Do not connect to any building's
electrical system except through an approved device or
after building main switch is opened.
3. Engine Oil Drain Plug - Removing the engine oil drain
plug while the engine is hot will result in hot oil to gush
out of the oil drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
CAUTION:
Never use damaged or worn cables when
connecting power tools or equipment to the
generator. Make sure power connecting
cables are securely connected to the
generator’s output terminals, insufficient
tightening of the terminal connections may
cause damage to the generator and
electrical shock.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 7
RULES FOR SAFE OPERATION
■ NEVER Run engine without air filter. Severe engine
damage may occur.
Battery
CAUTION:
Never over fill the battery with water above
the upper limit.
The battery contains acids that can cause injury to the eyes
and skin. To avoid eye irritation, always wear safety glasses.
Use well insulated gloves when picking up the battery. Use
the following guidelines when handling the battery:
■ Always service air cleaner frequently to prevent carburetor
malfunction.
■ Always disconnect the battery before performing service
on the generator.
■ Always be sure the operator is familiar with proper safety
precaution s and operations techniques before using
generator.
■ Always store equipment properly when not in use.
Equipment should be stored in a clean, dry location out of
the reach of children.
■ DO NOT leave the generator running in the manual mode
unattended.
■ DO NOT allow unauthorized people to operate this
equipment.
1. DO NOT drop the battery. There is the possibility of risk
that the battery may explode.
2. DO NOT expose the battery to open flames, sparks,
cigarettes etc. The battery contains combustible gases
and liquids. If these gases and liquids come in contact
with a flame or spark, an explosion could occur.
3. Always keep the battery charged. If the battery is not
charged a buildup of combustible gas will occur.
4. Always keep battery charging and booster cables in good
working condition. Repair or replace all worn cables.
5. Always recharge the battery in an open air environment,
to avoid risk of a dangerous concentration of combustible
gases.
6. In case the battery liquid (dilute sulfuric acid) comes in
contact with clothing or skin, rinse skin or clothing
immediately with plenty of water.
7. In case the battery liquid (dilute sulfuric acid) comes in
contact with your eyes, rinse eyes immediately with
plenty of water, then contact the nearest doctor or hospital,
and seek medical attention.
■ Always read, understand, and follow procedures in
Operator’s Manual before attempting to operate equipment.
■ Refer to the Isuzu Engine Owner's Manual for engine
technical questions or information.
Loading and Unloading (Crane)
■ Before lifting, make sure the generator's lifting hook is
secure and that there is no apparent damage to the
generator itself (loose screws, nuts and bolts). If any
part is loose or damaged, please take corrective action
before lifting.
■ Always drain fuel prior to lifting.
■ Always make sure crane or lifting device has been
properly secured to the hook of guard frame on generator.
■ NEVER lift the machine while the engine is running.
■ Use adequate lifting cable (wire or rope) of sufficient
strength.
■ When lifting the generator, always use the balanced
center-point suspension hook and lift straight upwards.
■ NEVER allow any person or animal to stand underneath
the machine while lifting.
■ When loading the generator on a truck, be sure to use
the front and back frame bars as a means to secure the
generator during transport.
PAGE 8 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
RULES FOR SAFE OPERATION
Transporting
■ Always shutdown engine before transporting.
■ Tighten fuel tank cap securely.
■ Drain fuel when transporting generator over long distances
or bad roads.
■ Always tie-down the generator during transportation by
securing the generator.
■ If generator is mounted on a trailer, make sure trailer
complies with all local and state safety transportation
laws. See page 10 for basic towing procedures.
Emergencies
■ Always know the location of the nearest fire extinguisher
and first aid kit. Know the location of the nearest telephone.
Also know the phone numbers of the nearest ambulance,
doctor and fire department.
Maintenance Safety
■ NEVER lubricate components or attempt service on a
running machine.
■ Always allow the machine a proper amount of time to
cool before servicing.
■ Keep the machinery in proper running condition.
■ Fix damage to the machine immediately and always
replace broken parts.
■ Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, coolant,
fuel, and fuel filters.
■ DO NOT use plastic containers to dispose of hazardous
waste.
■ DO NOT pour waste, oil, coolant or fuel directly onto the
ground, down a drain or into any water source.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 9
DCA-60SSI2 — TOWING RULES FOR SAFE OPERATION
Towing Safety Precautions
CAUTION :
Check with your county or state safety
towing regulations department before towing
your generator.
To reduce the possibility of an accident
while transporting the generator on public roads, always
make sure the trailer (Figure 1) that supports the generator
and the towing vehicle are in good operating condition and
both units are mechanically sound.
The following list of suggestions should be used when towing
your generator:
■ Make sure the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer "gross vehicle
weight rating" (GVWR).
■ ALWAYS inspect the hitch and coupling for wear. NEVER
tow a trailer with defective hitches, couplings, chains
etc.
■ Check the tire air pressure on both towing vehicle and
trailer. Also check the tire tread wear on both vehicles.
■ ALWAYS make sure the trailer is equipped with a "Safety
Chain".
■ ALWAYS attach trailer’s safety chain to bumper of towing
vehicle.
■ ALWAYS make sure the vehicle and trailer directional,
backup, brake, and trailer lights are connected and
working properly.
■ The maximum speed for highway towing is 45 MPH
unless posted otherwise. Recommended off-road towing
is not to exceed 10 MPH or less depending on type of
terrain.
■ Place chocked blocks underneath wheel to prevent
rolling, while parked.
■ Place support blocks underneath the trailer’s bumper to
prevent tipping, while parked.
■ Use the trailer’s hand winch to adjust the height of the
trailer, then insert locking pin to lock wheel stand in place,
while parked.
■ Avoid sudden stops and starts. This can cause skidding,
or jack-knifing. Smooth, gradual starts and stops will
improve gas milage.
■ Avoid sharp turns to prevent rolling.
■ Remove wheel stand when transporting.
■ DO NOT transport generator with fuel in tank.
Figure 1. Generator with Trailer
PAGE 10 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU — TRAILER-SAFETY GUIDELINES
CAUTION:
4.
ALWAYS make sure the trailer is in good
operating condition. Check the tires for
proper inflation and wear. Also check the
wheel lug nuts for proper tightness.
Explanation of Chart:
This section is to provide the user with trailer service and
maintenance information. The service and maintenance
guidelines referenced in this section apply a wide range of
trailers. Remember periodic inspection of the trailer will ensure safe towing of the equipment and will prevent damage
to the equipment and personal injury.
It is the purpose of this section to cover the major maintenance components of the trailer. The following trailer components will be discussed in this section:
„
„
„
„
„
„
Brakes
Tires
Lug Nut Torquing
Suspension
Electrical
Brake Troubleshooting Tables
Use the following definitions with reading Table 1.
1. Fuel Cell - Provides an adequate amount of fuel for the
equipment in use. Fuel cells must be empty when transporting equipment.
2. Braking System - System employed in stopping the
trailer. Typical braking systems are electric, surge, hydraulic, hydraulic-surge and air.
3. GVWR- Gross Vehicle Weight Rating (GVWR), is the
maximum number of pounds the trailer can carry, including the fuel cell (empty).
Frame Length - This measurement is from the ball
hitch to the rear bumper (reflector).
5. Frame Width - This measurement is from fender to
fender.
6.
Jack Stand - Trailer support device with maximum
pound requirement from the tongue of the trailer.
7. Coupler - Type of hitch used on the trailer for towing.
8. Tire Size - Indicates the diameter of the tire in inches
(10,12,14, etc.), and the width in millimeters
(175,185,205, etc.). The tire diameter must match the
diameter of the tire rim.
9. Tire Ply - The tire ply (layers) number is rated in letters;
2-ply,4-ply,6-ply, etc.
10. Wheel Hub - The wheel hub is connected to the trailer’s
axle.
11. Tire Rim - Tires mounted on a tire rim. The tire rim must
match the size of the tire.
12. Lug Nuts - Used to secure the wheel to the wheel hub.
Always use a torque wrench to tighten down the lug
nuts. See Table 4 and Figure 5 or lug nut tightening and
sequence.
13. Axle - Indicates the maximum weight the axle can support in pounds, and the diameter of the axle expressed
in inches (see Table 3). Please not that some trailers
have a double axle. This will be shown as 2-6000 lbs.,
meaning two axles with a total weight capacity of 6000
pounds.
14. Suspension - Protects the trailer chassis from shocks
transmitted through the wheels. Types of suspension
used are leaf, Q-flex, and air ride.
15. Electrical - Electrical connectors (looms) are provided
with the trailer so the brake lights and turn signals can
be connected to the towing vehicle.
16. Application - Indicates which units can be employed
on a particular trailer.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 11
DCA-60SSIU —TRAILER-SPECIFICATIONS
Table 1. Specifications
MODEL
APPLICATION
FU E L
C E LL
BRAKE
SYSTEM
GVWR
FRAME
LENGTH
FRAME
WIDTH
JACK
STAND
TRLR-10W
SDW225,
SGW250,TLW300
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-10
DCA10, TLG12,
DCA-15
NO
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-10XF
DCA10, TLG-12,
DCA15, TLW-300
52 GAL
NO
1900LB S
96"
50"
800LB .
FULL TILT WHEEL
TRLR-225W
WELDERS,
D A 7000S S
NO
NO
2200LB S
85"
42"
800LB .
FULL TILT WHEEL
TRLR-BLW400
BLW-400
NO
ELECTRIC
2700LB S
W/MAST 154"
W/O 124"
55"
(78" TALL)
800LB .
FULL TILT WHEEL
TRLR-50X
DCA-25
NO
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TRLR-50XF
DCA-25
41 GAL
NO
2700LB S
124"
55"
800LB .
FULL TILT WHEEL
TRLR-70W
DCA-45, -60, 70
NO
SURGE
7000LB S
186"
77"
2000LB .
FLAT PAD
TRLR-70X
DCA-45, -60, 70
OPT
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TRLR-70XF
DCA-45, -60, 70
53 GAL
SURGE
7000LB S
138"
66"
2000LB .
FLAT PAD
TRLR-100XF
DCA-100, 125
150 GAL
HYDRAULIC SURGE
7000LB S
190"
76"
2000LB .
FLAT PAD
TRLR-85/125
DCA-85, 100,
125
145 GAL
HYDRAULIC
10000LB S
186"
77"
2000LB .
FLAT PAD
TRLR-150XF
DCA-150, 180
200 GAL
HYDRAULIC SURGE
11160LBS
204"
84"
5000 LB .
FLAT PAD
TRLR-220XF
DCA-220
250 GAL
HYDRAULIC SURGE
14000LB S
222"
83"
5000 LB .
FLAT PAD
TRLR-300XF
DCA-300
250 GAL
HYDRAULIC SURGE
18000LB S
238"
83"
5000 LB .
FLAT PAD
TRLR-400XF
DCA-400
350 GAL
ELECTRIC
18000LB S
238"
83"
5000 LB .
FLAT PAD
TRLR-600XF
DCA-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
TRLR-800SX
DCA-600, 800
550 GAL
AIR
30000LB S
384"
96"
5000 LB .
FLAT PAD
PAGE 12 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU —TRAILER-SPECIFICATIONS
Table 1. Specifications (Con't)
MODEL
COUPLER
TIRES
WHEELS
AXLE
HUBS SUSPENSION
ELECTRICAL
TRLR-10W
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.50"
2200# 2X 2
5 LUG
3 LE A F
4 WIRE LOOM W/
4 POLE FLAT
TRLR-10
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-10XF
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13"X4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-225W
2" B A LL C LA S S
2 ADJUSTABLE
175-13B
13X4.5"
2200#2X 2
5 LUG
Q F LE X
4 POLE FLAT
TRLR-BLW
400
2" B A LL C LA S S
2 ADJUSTABLE
175-13C
13 X 4.5"
2200#2X 2
5 LUG
3 LE A F
4 POLE FLAT
TRLR-50X
2" B A LL C LA S S
B78-13LRC
13"X4.50"
3500lbs.
2-3/8"
5 LUG
4 LE A F
4 POLE RUBBER
FLAT
TRLR-50XF
2" B A LL C LA S S
B78-13LRC
13"X4.50"
3500lbs.
2-3/8"
5 LUG
4 LE A F
4 POLE RUBBER
FLAT
TRLR-70W
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs.
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-70X
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-70XF
2" B A LL C LA S S
3" ADJUSTABLE
205-14C
BIAS (4)
14" X 5"
3500lbs.
3"
5 LUG
5 LE A F
4 POLE RUBBER
FLAT
TRLR-100XF
ADJUSTABLE 2-5/6
OPT 3" EYE
205-15C
BIAS (4)
14"X5.5"
3500lbs
3"
5 LUG
5 LE A F
4 WIRE LOOM
TRLR-85/125
ADJUSTABLE 2-5/6
OPT 3" EYE
ST225/75R15D
RADIAL (4)
14"x6"
(2)-6000lbs
6 LUG
7 LE A F
4 WIRE LOOM
TRLR-150XF
3" BALL EYE
750-16 E
BIAS (4)
16" X 7"
(2)-6000lbs
8 LUG
7 LE A F
4 WIRE LOOM
TRLR-220XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(4)
16" X 7"
(2)-7000lbs
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-300XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(6)
16" X 7"
(2)-6000lbs
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-400XF
3" EYE
ADJUSTABLE
ST235/85R16E
RADIAL(6)
16" X 7"
(3)-7000lbs.
8 LUG
Q F LE X
4 WIRE LOOM
TRLR-600XF
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16" X 7"
(3)-10000lbs
8 LUG
7 LE A F
6 WIRE LOOM
TRLR-800AR
5TH WHEEL
ST215/75R17.5H
RADIAL (8)
16" X 7"
(3)-10000lbs
8 LUG
AIR-RIDE
6 WIRE LOOM
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 13
DCA-60SSIU —TRAILER SAFETY GUIDELINES
Brakes
If your trailer has a braking system, the brakes should be
inspected the first 200 miles of operation. This will allow
the brake shoes and drums to seat properly. After the first
200 mile interval, inspect the brakes every 3,000 miles. If
driving over rough terrain, inspect the brakes more
frequently.
Electric Brakes
Electrically actuated brakes (Figure 2) are similar to
hydraulic brakes. The basic difference is that hydraulic
brakes are actuated by an electromagnet.
Listed below are some of the advantages that electric
brakes have over hydraulic brakes:
„ Brake system can be manually adjusted to provide
the corrected braking capability for varying road and
load conditions
„ Brake system can be modulated to provide more or
less braking force, thus easing the brake load on the
towing vehicle
„ Brake system has very little lag time between the time
the vehicle’s brakes are actuated and the trailer’s brakes
are actuated
„ Brake system can provide an independent emergency
brake system
Remember in order to properly synchronize the tow vehicle’s
braking to the trailer’s braking, can only be accomplished
by road testing. Brake lockup, grabbiness or harshness is
due to lack of synchronization between the tow vehicle
and the trailer being towed or under-adjusted brakes.
Before any brake synchronizations adjustments can be
made, the trailer brakes should be burnished-in by applying
the brakes 20-30 times with approximately a 20 m.p.h.
decrease in speed, e.g. 40 m.p.h. to 20 m.p.h. Allow ample
time for brakes to cool between application. This allows
the brake shoes to slightly be seated into the brake drum
surface.
Figure 2 displays the major electric brake components that
will require inspection and maintenance. Please inspect
these components as required.
Electric Brake Adjustment
1. Place the trailer on jack stands. Make sure the jack
stands are placed on secure level ground.
2. Check the wheel and drum for free rotation.
3. Remove the adjusting hole cover from the adjusting
slot at the bottom brake backing plate.
4. With a screwdriver or standard adjusting tool, rotate
the star wheel of the adjuster assembly to expand the
brake shoes.
5. Adjust the brake shoes outward until the pressure of
the lining against the wheel drum makes the wheel
difficult to turn.
6. Rotate the star wheel in the opposite direction until the
wheel rotates freely with slight lining drag.
7. Replace the adjusting hole cover and lower the trailer
to the ground.
8. Repeat steps 1 through 6 on the remaining brakes.
PAGE 14 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU — TRAILER SAFETY GUIDELINES
Figure 2. Electrical Brake Components
Hydraulic/Air/Surge Brakes
Hydraulic brakes (Figure 3) should not require any special
attention with the exception of routine maintenance such
as shoe and lining replacement. These brakes can be
adjusted in the same manner as electric brakes. Brake
lines should be periodically checked for cracks, kinks, or
blockage.
Figure 3 below displays the major hydraulic/air/surge brake
components that will require inspection and maintenance.
Please inspect these components as required using steps
1 through 6 as referenced in the electric brake adjustments
section.
Figure 3. Hydraulic Brake Components
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 15
DCA-60SSIU — TRAILER SAFETY GUIDELINES
Tires/Wheels/Lug Nuts
Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing the
trailer wheels it is important the wheels, tires, and axle are
properly matched.
CAUTION:
DO NOT attempt to repair or modify a
wheel. DO NOT install in inner tube to
correct a leak through the rim. If the rim
is cracked, the
air pressure in
the inner tube
may cause pieces of the rim to
explode (break off) with great force
and cause serious eye or bodily
injury.
Tire Wear/Inflation
Tire inflation pressure is the most important factor in tire life.
Pressure should be checked cold before operation DO NOT
bleed air from tires when they are hot. Check inflation
pressure weekly during use to insure the maximum tire life
and tread wear.
Table 2 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
Suspension
The leaf suspension springs and associated components
(Figure 4) should be visually inspected every 6,000 miles for
signs of excessive wear, elongation of bolt holes, and
loosening of fasteners. Replace all damaged parts
(suspension) immediately. Torqued suspension components
as detailed in Table 3.
CAUTION:
NOTE
ALWAYS wear safety glasses when removing
or installing force fitted parts. Failure to comply
may result in serious injury.
Figure 4. Major Suspension Components
PAGE 16 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU —TRAILER SAFETY GUIDELINES
Table 3. Suspension Torque Requirements
Item
Torque (Ft.-Lbs.)
3/8" U-BOLT
MIN-30 MAX-35
7/16" U-BOLT
MIN-45 MAX-60
1/2" U-BOLT
MIN-45 MAX-60
SHACKLE BOLT
SNUG FIT ONLY. PARTS MUST ROTATE FREELY.
SPRING EYE BOLT
LOCKING NUTS OR COTTER PINS ARE PROVIDED TO
RETAIN NUT-BOLT ASSEMBLY.
MIN-30 MAX-50
SHOULDER TYPE
SHACKLE BOLT
Lug Nut Torque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque on the trailer. Be sure to use only the
fasteners matched to the cone angle of the wheel. Proper
procedure for attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence. See Figure 5. DO NOT
torque the wheel lug nuts all the way down. Tighten
each lug nut in 3 separate passes as defined by Table 4.
3. After first road use, retorque all lug nuts in sequence.
Check all wheel lug nuts periodically.
Table 4. Tire Torque Requirements
Wheel Size
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
12"
20-25
35-40
50-65
13"
20-25
35-40
50-65
14"
20-25
50-60
90-120
15"
20-25
50-60
90-120
16"
20-25
50-60
90-120
Figure 5. Wheel Lug Nuts Tightening Sequence
NOTE
NEVER use an pneumatic air gun to
tighten wheel lug nuts.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 17
DCA-60SSIU —TRAILER-WIRING DIAGRAM
NOTE:
LIGHTS ARE ORIENTED FROM THE DRIVER’S SEAT
PAGE 18 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU —TRAILER-BRAKE TROUBLESHOOTING
Table 5. Electric Brake Troubleshooting
Symptom
Possible Cause
Solution
No Brakes or Intermittent Brakes
Any open circuits or broken wires?
Find and correct.
Any shor t circuits?
Find and correct.
Faulty controller?
Test and correct.
Any loose connections?
Find and repair.
Ground wire secure?
Find and secure.
Grease or oil on magnets or linings?
Clean or replace.
Connections corroded?
Clean and correct cause
of corrosion.
Brake drums scored or grooved?
Machine or replace.
Brakes synchronized?
Correct.
Brake components loose, bent or broken?
Replace components.
Brake drums out-of-round?
Replace.
System lubricated?
Lubricate.
Brake components correct?
Replace and correct.
Bearings of the wheel adjusted?
Adjust.
Weak Brakes or Brakes Pull to
One Side
Locking Brakes
Noisy Brakes
Dragging Brakes
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 19
DCA-60SSIU —TRAILER-BRAKE TROUBLESHOOTING
Table 6. Hydraulic Brake Troubleshooting
Symptom
Possible Cause
Solution
No Brakes
Brake line broken or kinked?
Repair or replace.
Weak Brakes or Brakes Pull to
One Side
Brake lining glazed?
Reburnish or replace.
Trailer overloaded?
Correct weight.
Brake drums scored or grooved?
Machine or replace.
Tire pressure correct?
Inflate all tires equally.
Tires unmatched on the same axle?
Match tires.
Brake components loose, bent or broken?
Replace components.
Brake drums out-of-round?
Replace.
System lubricated?
Lubricate.
Brake components correct?
Replace and correct.
Brake lining thickness correct or in right
wrong position?
Install new shoes and
linings.
Enough brake fluid or correct fluid?
Replace rubber par ts
fill with dot4 fluid.
Locking Brakes
Noisy Brakes
Dragging Brakes
PAGE 20 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — GENERATOR DECALS
The DCA -100SSJU generator is wquipped with a number of safety decals. These decals are provided for operator safety
and maintenance information. The illustration below and on the preceding pages show the decals as they appear on the
machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 21
DCA-60SSI2 — GENERATOR DECALS
PAGE 22 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — SPECIFICATIONS
Table 7. Specifications
Generator Specifications
Model
DCA-60SSI2
Type
Revolving field, self ventilated, open protected type synchronous generator
Armature Connection
Star with Neutral
Zig Zag
Phase
3
Single
Standby Output
72 KVA (57.6 KW)
41.5KW
Prime Output
60 KVA (48 KW)
34.6KW
Voltage
240V or 480V
240/120V
Frequency
60 Hz
Speed
1800 rpm
Power Factor
0.8
1
Aux. AC Power
Single Phase, 60 Hz
Voltage
120 V
Output
4.8 KW (2.4 KW x 2)
Engine Specifications
Model
ISUZU A-6BG1
Type
4 Cycle, water-cooled, direct injection
No. of Cylinders
6 cylinders
Bore x Stroke
4.1 in. x 4.9 in. (105 mm x 125 mm)
Rated Output
77HP/1800 rpm
Displacement
396 cu. in. (6494 cc)
Starting
Electric
Coolant Capacity
7.8 gal. (29.5 liters)
Lube Oil Capacity
5.1 gal. (19.3 liters)
3.9 gal. (14.9L)/hr at full load
3.0 gal. (11.4L)/hr at 3/4 load
2.4 gal. (9.1L)/hr at 1/2 load
1.9 gal. (7.2L)/hr at 1/4 load
Fuel Consumption
Battery
12V- 100AH x 2
Fuel
#2 Diesel Fuel
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 23
DCA-60SSI2 — GENERAL INFORMATION
DCA-60SSI2 FAMILIARIZATION
Open Delta Excitation System
Generator
The DCA-60SSI2 generator is equipped with the state of
ator the art "Open-Delta" excitation system. The open delta
The MQ Power Model DCA-60SSI2 is a 48 kW gener
generator
that is designed as a high quality portable (requires a trailer system consist of an electrically independent winding wound
for transport) power source for telecom sites, lighting among stationary windings of the AC output section.
facilities, power tools, submersible pumps and other There are four leads: A, B, C and D. During light loads, the
industrial and construction machinery.
power to the Automatic Voltage Regulator (AVR) is supplied
from the leads parallel connections of B&C. When loads
Engine Operating Panel
increase, the AVR switches and accepts power from leads
The “Engine Operating Panel” is provided with the following: A&D. The output of leads A&D increase proportionally with
z Tachometer
load. This of adding the voltages to each phase provides
z Water Temperature Gauge
better voltage response during heavy loads.
z Oil Pressure Gauge
The connections of the AVR to the AC output windings are
z Charging Ammeter Gauge
for sensing only. No power is required from these windings.
z Engine Throttle Lever
z Panel Light
The open-delta design provides virtually unlimited excitation
z Panel Light Switch
current, offering maximum motor starting capabilities. The
z Oil Pressure and WaterTemp. Indicator lights
excitation does not have a "fixed ceiling" and responds
according the demands of the required load.
Generator Control Panel
The “Generator Control Panel” is provided with the following: Engine
z Output Voltage Adjustment Knob
The DCA-60SSI2 is powered by a 4 cycle, water cooled,
z Frequency Meter (Hz)
Isuzu A-6BG1diesel engine. This engine is designed to
z AC Ammeter (Amps)
meet every performance requirement for the generator.
z AC Voltmeter (Volts)
Reference Table 1, page13 for engine specifications.
z Ammeter Change-Over Switch
In keeping with Multiquip's policy of constantly improving
z Voltmeter Change-Over Switch
its products, the specifications quoted herein are subject to
change without prior notice.
Output Terminal Panel
The basic controls and indicators for the DCA-60SSI2
The “Output Terminal Panel” is provided with the following:
generator are addressed on the following pages.
z Three 120/240V output receptacles, 50 amp
z Two 120V input receptacles, 20 amp
z 3 Load Circuit Breakers 240V @50 amps
z 2 Load GFCI Circuit Breakers [email protected] 20amps
Mechanical Governor System
The mechanical governor system control the RPM of the
Control Box
engine. When the engine demands increase or decrease,
The “Control Box” is provided with the following:
the mechanical governor system regulates the frequency
z Main Circuit Breaker 150 amps
variation to ±1.5%. The electronic governor option inz Over-Current Relay
creases frequency variation to ±.25%.
PAGE 24 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — MAJOR COMPONENTS
Figure 6. Major Components
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 25
DCA-60SSI2 — DIMENSIONS (TOP, SIDE AND FRONT)
Figure 7. Dimensions
PAGE 26 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
NOTE PAGE
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 27
DCA-60SSI2 — CONTROL PANEL
Figure 8. Control Panel
PAGE 28 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — CONTROL PANEL
The definitions below describe the controls and functions of
the DCA-60SSI2 " Control Panel " (Figure 8).
1.
Frequency Meter – Indicates the output frequency in
hertz (Hz). Normally 60 Hz ±1 Hz .
2.
AC Ammeter – Indicates the amount of current the
load is drawing from the generator.
3.
ACVoltmeter – Indicates the single phase output
voltage present at the UNV terminals.
4.
Pilot Lamp - This lamp indicates the load is not properly
set. Readjust the load, or use the voltmeter changeover switch to adjust phase position.
Main Circuit Breaker – This three-pole, 150 amp main
breaker is provided to protect the UNV voltage output
terminals from overload.
5.
6.
Voltmeter Change-Over Switch – This switch allows
the AC voltmeter to indicate phase to phase voltage
between any two phases of the output terminals or to
be switched off.
7.
Ammeter Change-Over Switch – This switch allows
the AC ammeter to indicate the current flowing to the
load connected to any phase of the output terminals, or
to be switched off.
8.
Voltage Regulator Control – Allows manual
adjustment of the generator’s output voltage.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 29
DCA-60SSI2 — ENGINE OPERATING PANEL
Figure 9. Engine Operating Panel
PAGE 30 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — ENGINE OPERATING PANEL
The definitions below describe the controls and functions of
the DCA-60SSI2 " Engine Operating Panel " (Figure 9).
1.
Oil Pressure Gauge – Normal operation should be about
25 psi. When starting the generator the oil pressure
may read a bit higher, but after the engine warms up
the oil pressure should return to normal.
2.
Panel light - Normally used in dark places or at night.
When activated, panel will luminate. When the generator
is not in use, turn the panel light switch to the ‘OFF’
position.
3.
Water Temperature Gauge – During normal operation
this gauge be should read between 165o to 215o.
Charging Ammeter Gauge – Indicates the current
being supplied by the engine’s alternator which provides
current for generator’s control circuits and battery
charging system.
Indicator Lights - These lights indicate if the oil
pressure or water temperature is at dangerous levels
and will shut off the engine. The oil pressure indicator
will initially light at start-up, but will go off once the
pressure rises.
4.
5.
6.
Panel light switch- When activiated, will turn on control
panel light.
7.
Lamp Check Switch - This is used to check the
indicator lights. Turn on the engine, then press this to
check the bulbs. If they don’t light, replace the bulbs.
8.
Engine Throttle Lever - Pull or push this lever to change
the speed of the engine when a load is applied.
9.
Pre-Heat Indicator – Under cold conditions, turn the
starter key to preheat. Once the indicator lights, the
engine is ready to start.
10. Starter Switch - Turn this to start, stop, and preheat
the engine.
11. Tachometer – Indicates engine speed in RPM’s for 60
Hz operation. This meter should indicate 1800 RPM’s
when the engine is at full speed and a load is applied.
In addition, a built in hour meter will record the number
of operational hours that the generator has been in use.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 31
DCA-60SSIU — OUTPUT TERMINAL PANEL
Output Terminal Panel
The output control panel is located on the rear (control panel)
end of the generator. The UNV lugs are protected by a face
plate cover that can be secured in the close position by a
pad lock.
120 Volt Receptacle
One GFCI Duplex NEMA 5-20R (120V, 20 Amp) receptacle
is located on the output terminal. This receptacle can be
used anytime the generator is in operation. The receptacle
is controlled by the circuit breaker located on the control
panel.
The reset button will reset the receptacle after being tripped.
Pressing the :Test Button” (Figure 8) in the center of this
receptacle will check the GFCI function. The receptacle
should be tested at least once a month.
Twist Lock Dual Voltage Receptacles - To use these
receptacles, place the voltage selector switch in the single
phase 240/120 voltage position and adjust the output
voltage to 240 volts with the voltage regulator on the
Control Panel (Figure 8, page 28). Place the voltmeter
change-over switch to the U-W position and the ammeter
change-over switch to the U or W to read the output.
Connecting Load
Loads can be connected to the generator by the UVWO lugs or
the duplex receptacles. (See figure 3). Make sure to read the
operation manual before attempting to connect a load to the
generator.
Figure 11. Load Application
Circuit Breakers
Figure 10. GFCI Test Button
Generator Grounding
Make sure the generator is properly grounded before
applying load. Generators are NOT considered grounded
when mounted on a trailer.
To protect the generator from an overload, a 3-pole, 150 amp,
main circuit breaker is provided to protect the UVWO output
terminals from overload. In addition two single-pole, 20 amp
GFCI circuit breakers are provided to protect the GFCI
receptacles from overload. Three 50 amp load circuit
breakers have also been provided to protect the load side of
the generator from overload. Make sure to switch ALL circuit
breakers to the "OFF" position prior to starting the engine.
Maximum Output
The entire load connected to the UVWO lugs, all four slots in
the duplex receptacles, and the must not exceed 52.8 kW in
standby or 48 kW in prime output.
Generator Grounding
Make sure to ground the generator in EVERY application
prior to connecting a load. Generators are NOT grounded
just because they are mounted on trailers or other vehicles
that are on rubber tires.
PAGE 32 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU — OUTPUT TERMINAL VOLTAGE SELECTION
DCA-60SSIU
NOTE
Legs O and Ground are
considered Bonded Grounds.
Figure 12. Output Panel Location
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 33
DCA-60SSIU — OUTPUT AMPERAGE SETUP
Output Terminal Panel Available Voltages
A wide range of voltages are available to supply load to
many different applications. Voltages may be selected by
using the voltage selector switch and depending how you
hookup your hard wire connection to the generator. To obtain
some of the voltages listed, fine adjustment with the voltage
regulator on the control panel is necessary. See Table 8 for
available voltages the generator will supply.
Over Current Relay
An over current relay is connected to the circuit breaker.
During an over current situation, both the circuit breaker and
the over current relay will trip. If the circuit breaker can not
be reset, the reset button on the over current relay must be
pressed. The over current relay is located inside the control
box.
Table 8. Voltage Available
3 Phase
(Switchable)
208 VOLT
220 VOLT
240 VOLT
416 VOLT
440 VOLT
480 VOLT
Single Phase
(Switchable)
120 VOLT
127 VOLT
139 VOLT
240 VOLT
254 VOLT
277 VOLT
CAUTION :
NEVER switch Voltage Selector Switch
position while the engine is engaged.
Voltage Selector Switch Locking Button
The voltage selector switch has a locking button to protect
the generator and generator load from being switched while
the engine is running. To lock the voltage selector switch,
press in the red button located on the voltage selector switch,
and use a pad lock to hold it into this position.
Maximum Amps
Table 9 shows the maximum amps the generator will provide. Do not exceed the maximum amps listed.
Table 9. Maximum Amps
Rated
Voltage
Maximum Amps
Single Phase
120 Volt
133.3 amps (4 wire)
Single Phase
240 Volt
66.7 amps (4 wire)
Three Phase
240 Volt
144 amps
Three Phase
480 Volt
72 amps
PAGE 34 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU — OUTPUT AMPERAGE SETUP
Receptacle Use
When the UVWO terminals are providing power, the receptacle power availability will decrease.
How To Read The Output Terminal Gauges.
The gauges (Figure 15 and 17) and change-over switches
on the control panel DO NOT effect the generator output.
They are to help observe how much power is being supplied
at the UVWO legs.
When the voltage selector switch is in the 240/120V position (Figure 13), place the AC voltmeter change-over switch
to the W-U position (Figure 14) and the AC ammeter changeover switch to the U or W position (Figure 16) to read the
output on the selected leg.
Figure 14 and 15. AC Voltmeter Change-over switch
and Voltmeter Gauge
Figure 16 and 17. AC Ammeter Change-over Switch
and Ammeter Gauge
NOTE
Figure 13. Voltage Selector Switch 240/120V Single
Phase
Position
When using plural single phase
voltages, make sure to balance
the load on each of the single
phase legs.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 35
DCA-60SSIU — OUTPUT VOLTAGE SETUP
240/120V Hard Wire Hookup
480/240V Hard Wire Hookup
With the voltage selector set and locked at ‘single phase
240/120’ and using single phase 120 volts, the generator
will provide three legs available with 100 amps each on three
different circuits (Figure 18).
With the voltage selector set and locked at ‘3 phase 480/
277’ (Figure 19) and using the 3-phase 240 hookup, it will
provide one circuit available at 108 amps with any two wires
plus the ground (Figure 20).
When using the 3-phase 480 volts hookup, it will provide
one circuit available at 50 amps with all three wires plus
ground.
Figure 19. Voltage Selector Switch 480/277V Three Phase
Position
Figure 18. Hard Wire Hookup at 240/120V Position
Figure 20. Hard Wire Hookup at 480/240V Position
PAGE 36 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU — OUTPUT VOLTAGE SETUP
Voltage Selector Switch- 3 Phase 480/277V Position
The following are additional voltages available when the voltage selector switch is in the ‘3 phase 480/277V’ position.
Single Phase: 480V, 440V, or 416 Volt
This setting can provide single phase power at 480, 440, or
416 volts. After hooking up the hard wires to the lugs as
shown in Figure 23, 480 volts can be obtained with the voltage regulator knob turned toward maximum; 440 volts can
be obtained with the voltage regulator knob is turned down;
and 416 volts can be obtained with the voltage regulator
knob is at the lowest setting.
Figure 21. Voltage Regulator Knob
3 Phase, 480V, 440V, or 416 Volt
This setting can provide 3-phase power at 480, 440, or 416
volts. After hooking up the hard wires to the lugs as shown
in Figure 22, 480 volts can be obtained with the voltage
regulator knob turned toward maximum; 440 volts can be
obtained with the voltage regulator knob is turned down; and
416 volts can be obtained with the voltage regulator knob is
at the lowest setting.
Figure 23. Hard Wire Hookup for Single Phase 480V, 440V,
or 416V
Single Phase: 277V, 254V, or 240V
This setting can provide single phase power at 277, 254, or
240 volts. After hooking up the hard wires to the lugs as
shown in Figure 24, 277 volts can be obtained with the voltage regulator knob turned toward maximum; 254 volts can
be obtained with the voltage regulator knob is turned down;
and 240 volts can be obtained with the voltage regulator
knob is at the lowest setting.
Figure 22. Hard Wire Hookup for Three Phase 480V, 440V, or
416V
Figure 24. Hard Wire Hookup for Single Phase 277V, 254V,
or 240V
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 37
DCA-60SSIU — OUTPUT VOLTAGE SETUP
Voltage Selector Switch- 3 Phase 240/139V Position
The following are additional voltages available when the voltage selector switch is in the ‘3 phase 240/139V’ position.
Figure 25. Voltage Selector Switch 240/139V Three Phase
Position
Single Phase: 240V, 220V, or 208 Volt
This setting can provide single phase power at 240, 220, or
208 volts. After hooking up the hard wires to the lugs as
shown in Figure 27, 240 volts can be obtained with the voltage regulator knob turned toward maximum; 220 volts can
be obtained with the voltage regulator knob is turned down;
and 208 volts can be obtained with the voltage regulator
knob is at the lowest setting.
Figure 27. Hard Wire Hookup for Single Phase 240V, 220V,
or 208V
Single Phase: 139V, 127V, or 120V
3 Phase, 240V, 220V, or 208 Volt
This setting can provide single phase power at 139, 127, or
This setting can provide 3-phase power at 240, 220, or 208 120 volts. After hooking up the hard wires to the lugs as
volts. After hooking up the hard wires to the lugs as shown shown in Figure 28, 139 volts can be obtained with the voltin Figure 26, 240 volts can be obtained with the voltage age regulator knob turned toward maximum; 127 volts can
regulator knob turned toward maximum; 220 volts can be be obtained with the voltage regulator knob is turned down;
obtained with the voltage regulator knob is turned down; and and 120 volts can be obtained with the voltage regulator
208 volts can be obtained with the voltage regulator knob is knob is at the lowest setting.
at the lowest setting.
Figure 26. Hard Wire Hookup for Three Phase 240V, 220V, or
208V
Figure 28. Hard Wire Hookup for Single Phase 139V, 127V,
or 120V
PAGE 38 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU — OUTPUT VOLTAGE SETUP
Voltage Selector Switch- Single Phase 240/120V
Position
The following are additional voltages available when the voltage selector switch is in the ‘single phase 240/120V’ position.
Single Phase: 120 Volt
This setting can provide single phase power at 120 volts.
After hooking up the hard wires to the lugs as shown in
Figure 31, 120 volts can be obtained with the voltage regulator knob turned to fine tune.
Figure 31. Hard Wire Hookup for Single Phase, 120 volt
Figure 29. Voltage Selector Switch 240/120V Single Phase
Position
Single Phase, 240 Volt
This setting can provide single phase power at 240 volts.
After hooking up the hard wires to the lugs as shown in
Figure 30, 240 volts can be obtained with the voltage regulator knob turned to fine tune.
Figure 30. Hard Wire Hookup for Single Phase 240 volt
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 39
DCA-60SSI2 — INSTALLATION
Outdoor Installation
Install the generator in a location where it will not be exposed
to rain or sunshine. Make sure the generator is on secure
level ground so that it cannot slide or shift around. Also
install the generator in a manner so that the exhaust will not
be discharged in the direction of nearby homes.
CAUTION :
An electric shock may happen when
vibrators are used. Pay close attention to
handling when operating vibrators and
always use rubber boots and gloves to
insulate the body from electrical shock.
Generator Grounding
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from To guard against electrical shock and possible damage to
excessive moisture. Failure to do will result in deterioration the equipment, it is important to provide a good EARTH
of the insulation and will result in short circuits and grounding. ground.
Article 250 (Grounding) of the National Electrical Code (NEC)
provides guide lines for proper grounding and specifies that
Foreign materials such as dust, sand, lint and abrasive
the cable ground shall be connected to the grounding system
materials have a tendency to cause excessive wear to
of the building as close to the point of cable entry as
engine and alternator parts.
practical.
CAUTION :
NEC articles 25064(b) a and 250-66 set the following
grounding requirements:
Pay close attention to ventilation when
1. Use one of the following wire types to connect the
operating the generator inside tunnels and
generator to earth ground.
caves. The engine exhaust contains
a. Copper - 10 AWG (5.3 mm2) or larger.
noxious elements. Engine exhaust must
be routed to a ventilated area.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
Indoor Installation
2. When grounding the generator (Figure 32) connect the
ground cable between the lock washer and the nut on
the generator and tighten the nut fully. Connect the other
end of the ground cable to earth ground.
Exhaust gases from diesel engines are extremely poisonous.
Whenever an engine is installed indoors the exhaust fumes 3. NEC article 250-52(c) specifies that the earth ground
rod should be buried a minimum of 8 ft. into the ground.
must be vented to the outside. The engine should be installed
at least two feet from any outside wall. Using an exhaust
pipe which is too long or too small can cause excessive
back pressure which will cause the engine to heat
excessively and possibly burn the valves.
NOTE
Mounting
When connecting the generator to any buildings
The generator must be mounted on a solid foundation (such
electrical system ALWAYS consult with a licensed
as concrete) and set firmly on the foundation to isolate
electrician.
vibration of the generator when it is running. The generator
must set at least 6 inches above the floor or grade level (in
accordance to NFPA 110, Chapter 5-4.1). DO NOT remove
the metal skids on the bottom of the generator. They are to
resist damage to the bottom of the generator and to maintain
alignment.
PAGE 40 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — INSTALLATION
Figure 32.
Typical Generator Grounding Application
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 41
DCA-60SSI2 — PRE-SETUP
General Inspection Prior to Operation
Circuit Breakers
The DCA-60SSI2 generator has been thoroughly inspected
and accepted prior to shipment from the factory. However,
be sure to check for damaged parts or components, or loose
nuts and bolts, which could have occurred in transit.
Extension Cable
To protect the generator from an overload, a 3-pole, 150 amp,
main circuit breaker is provided to protect the UNV output
terminals from overload. In addition two single-pole, 20 amp
GFCI circuit breakers are provided to protect the GFCI
receptacles from overload. Three 50 amp load circuit breakers
have also been provided to protect the load side of the
When electric power is to be provided to various tools or generator from overload. Make sure to switch ALL circuit
loads at some distance from the generator, extension breakers to the "OFF" position prior to starting the engine.
cords are normally used. Cables should be sized to allow
for distance in length and amperage so that the voltage
drop between the generator and point of use (load) is held
to a minimum. Use the Cable Selection Guide (Table 10)
as a guide for selecting proper cable size.
NOTE
ALWAYS consult with a licensed
electrician for correct extension
cord wire size.
Table 10. Cable Selection (60 Hz, Single Phase Operation)
Load In Watts
Current in
Amperes At 120 At 240
Volts
Volts
Maximum Allowable Cable Length
#10 Wire
#12 Wire
#14 Wire
#16 Wire
2.5
300
600
1000 ft.
600 ft.
375 ft.
250 ft.
5
600
1200
500 ft.
300 ft.
200 ft.
125 ft.
7.5
900
1800
350 ft.
200 ft.
125 ft.
100 ft.
10
1200
2400
250 ft.
150 ft.
100 ft.
15
1800
3600
150 ft.
100 ft.
65 ft.
20
2400
4800
125 ft.
75 ft.
50 ft.
CAUTION: Equipment damage can result from low voltage.
PAGE 42 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — PRE-SETUP
Lubrication Oil
Fill the engine crankcase with lubricating oil through the filler
hole, but do not overfill. Make sure the generator is level.
With the dipstick inserted all the way, but without being screw
into the filler hole, verify that the oil level is maintained
between the two notches (Figure 33) on the dipstick. See
Table 11 for proper selection of engine oil.
Fuel
Fill the fuel tank with clean and fresh diesel fuel. DO NOT
fill the tank beyond capacity.
Pay attention to the fuel tank capacity when replenishing
fuel. Refer to the fuel tank capacity listed on page 23,
Specification Table 7.
The fuel tank cap must be closed tightly after filling. Handle
fuel in a safety container. If the container does not have a
spout, use a funnel. Wipe up any spilled fuel immediately.
CAUTION:
Never fill the fuel tank while the engine is
running or in the dark. Diesel spillage on
a hot engine can cause a fire or
explosion. If diesel spillage occurs, wipe
up the spilled diesel completely to
prevent fire hazards.
Figure 33. Engine Oil Dipstick
Coolant
Use only drinkable tap water. If hard water or water with
many impurities is used, the inside of the engine and radiator
may become coated with deposits and cooling efficiency
will be reduced.
An anticorrosion additive added to the water will help prevent
When checking the engine oil, be sure to check if the oil is deposits and corrosion in the cooling system. See the engine
clean and viscous. If the oil is not clean, drain the oil by manual for further details.
removing the oil drain plug, and refill with the specified amount
of oil as outlined in the Isuzu Engine Owner's Manual.
Table 11. Recommended Motor Oil
Temperature Range
Type Oil
104° F ~ 23° F
(40° C ~ -5°C)
SAE 30
23° F ~ 5° F
(-5° C ~ -15°C)
SAE 20 or SAE 10W-30
Below 5° C (-15°)
SAE 10W or SAE 10W-30
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 43
DCA-60SSIU — PRE-SETUP
CAUTION :
When adding coolant or antifreeze to the
radiator, do not remove the radiator cap
until the unit has completely cooled.
Day-to-day addition of coolant is done from the reserve tank.
When adding coolant to the radiator, DO NOT remove the
radiator cap until the unit has completely cooled. See Table
12. for engine, radiator, and reserve tank coolant capacities.
Make sure the coolant level in the reserve tank is always
between the "H" and the "L" markings.
Table 12. Coolant Capacity
Engine and Radiator
7.8 Gal. (29.5 Liter)
Reserve Tank
.95 Gal. (2 Liter)
Cleaning the Outer Radiator
The engine may overheat if the radiator fins become
overloaded with dust or debris. Periodically clean the radiator
fins with compressed air. Cleaning inside the radiator is
dangerous, so clean only with the engine turned off and the
battery disconnected.
Air Cleaner
Periodic cleaning/replacement is necessary. Inspect it in
accordance with the Isuzu Engine Owner's Manual.
Fan Belt Tension
A slack fan belt may contribute to overheating, or to
insufficient charging of the battery. Inspect the fan belt for
damage and wear and adjust it in accordance with the Isuzu
Engine Owner's Manual.
The fan belt tension is proper if the fan belt bends 10 to 15
mm (Figure 34) when depressed with the thumb as shown
below. Never place hands near the belts or fan while the
generator is running.
Operation in Freezing Weather
When operating in freezing weather, be certain the proper
amount of antifreeze (Table 13) has been added.
Table 13. Anti-Freeze Operating Temperatures
Freezing Point
Boiling Point
Vol %
Anti-Freeze
°C
°F
°C
°F
40
-24
-12
106
222
50
-37
-34
108
226
NOTE
When the antifreeze is mixed with
w ater
atio m
ust
ater,, the antifreez
antifreezee mixing rratio
must
be less than 50%.
Figure 34. Fan Belt Tension
CAUTION :
Never place hands near the belts or fan
while the generator set is running.
Adjusting Fan Belt
If the fan belt does not have the 10 to 15 mm defection
follow the procedure below to adjust:
Loosen the alternator adjusting plate and alternator mounding
bolt.
Pivot the alternator at the mounting bolt toward the engine
left or right until the belt reflects the proper tension.
Tighten the mounting bolt and the adjusting bolt.
PAGE 44 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU — PRE-SETUP
Battery
This unit is of negative ground. DO NOT connect in reverse.
Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level is not
properly maintained. Add only distilled water when
replenishment is necessary. DO NOT over fill.
The battery is sufficiently charged if the specific gravity of
the battery fluid is 1.28 (at 68° F). If the specific gravity
should fall to 1.245 or lower, it indicates that the battery is
dead and needs to be recharged or replaced.
Check to see whether the battery cables are loose. Poor
contact may result in poor starting or malfunctions. Always
keep the terminals firmly tightened. Coating the terminals
with a thin film of grease will help to inhibit corrosion.
Battery Cable Installation
ALWAYS be sure the battery cables (Figure 35) are properly
connected to the battery terminals as shown below. The RED
cable is connected to the positive terminal of the battery,
and the BLACK cable is connected to the negative terminal
of the battery.
CAUTION :
If the battery cable is connected
incorrectly, damage to the generator will
occur. Pay close attention to the polarity
of the battery when connecting the
battery.
When connecting battery do the following:
1. DO NOT connect the battery cables to the battery
terminals when the key is in the ignition and is set in
'START' mode. ALWAYS remove the key from the
ignition and the ignition switch is in the OFF position
when connecting the battery.
2. Place a small amount of grease around both battery
terminals. This will ensure a good connection and will
help prevent corrosion around the battery terminals.
CAUTION :
Inadequate battery connections may
cause poor starting of the generator, and
create other malfunctions.
Wiring
Inspect the entire generator for bad or worn electrical wiring
or connections. If any wiring or connections are exposed
(insulation missing) replace wiring immediately.
Piping and Hose Connection
Inspect all piping, oil hose, and fuel hose connections for
wear and tightness. Tighten all hose clamps and check hoses
for leaks.
Figure 35. Battery Connections
If any hose (fuel or oil) lines are defective replace them
immediately.
Alternator
The polarity of the alternator is negative grounding type.
When an inverted circuit connection takes place, the circuit
will be in short circuit instantaneously resulting the alternator
failure.
Do not put water directly on the alternator. Entry of water
into the alternator leads an electrolyte corrosion causing an
alternator failure.
Before charging the battery with an external electric source,
be sure to disconnect the battery cables.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 45
DCA-60SSI2 — LOAD APPLICATION
Single Phase Load
CAUTION:
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generator for operating the equipment.
Motors and motor-driven equipment draw
much greater current for starting than
during operation.
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
An inadequate size connecting cable which cannot carry
the required load can cause a voltage drop which can burn
out the appliance or tool and overheat the cable.
When the voltage selector switch is in single phase (240/
120V position), place the AC voltmeter change-over switch
to the U-W position and the AC ammeter change over-switch
to the U or W position to read the ouput.
NOTE
If wattage is not given on the
equipment's name plate, approximate
wattage may be determined by
multiplying nameplate voltage by the
nameplate amperage.
WATTS = VOLTAGE x AMPERAGE
The power factor of this generator is 1.0. See Table 14.
below when connecting loads.
Table 14. Power Factor By Load
Type Of Load
Power Factor
Single-phase induction motors
0.4 - 0.75
Electric heaters, incandescent
lamps
1.0
Fluorescent lamps, mercury lamps
0.4 - 0.9
Electronic devices, communication
equipment
1.0
Common power tools
0.8
z When connecting a resistance load such as an
incandescent lamp or electric heater, a capacity of up
to the generating set’s rated output (kW) can be used.
z When connecting a fluorescent or mercury lamp, a
capacity of up to the generating set’s rated output (kW)
multiplied by 0.6 can be used.
z When connecting an electric drill or other power tools,
pay close attention to the required starting current
capacity.
If wattage is not available on the equipment, approximate
wattage may be determined by mulitplying the nameplate
voltage by the nameplate amperage for three-phase:
WATTS =1.732 x VOLTAGE x AMPERAGE
CAUTION:
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch. Serious injury or death
may result without this transfer switch.
NOTE
If output (kVA) is not given on the
equipment nameplate, approximate
output may be determined by
multiplying voltage by amperage by
Three Phase Load
When calculating the power requirements for 3-phase power
use the following equation:
PAGE 46 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — GENERATOR START-UP PROCEDURE
WARNING:
The engine's exhaust contains harmful
W AY S ventilate the
emissions. A LLW
exhaust when operating inside tunnels,
excavations or buildings. Direct exhaust
away from nearby personnel.
2. Connect the load to the UVW terminals as shown in
Figure 37. These terminals can be found on the output
terminal panel, (see page 22 Figure 6). To gain access
to the output terminals lift the UVW cover. Tighten
terminal nuts securely to prevent load wires from slipping
out.
Before Starting
Engine
1. Check the lubricating oil level prior to starting the engine.
Make sure the generator is level. The oil level must be
maintained between two notches on the dipstick.
2. When there is not enough lubricating oil, fill the crankcase
with high grade motor oil. Use a high quality detergent
oil classified CC or higher (See Table 11 on page 43).
3. Check the coolant level in the radiator and subtank.
Replenish with antifreeze as necessary. Always maintain
the coolant level between the FULL and LOW markings
on the coolant container. Be sure that the radiator cap is
fastened securely.
4. Check the fuel level on the fuel gauge. If fuel is low, fill
the fuel tank with clean fresh unleaded automotive diesel.
If diesel spillage occurs, completely wipe up the spilled
fuel immediately.
Figure 37. UVW Terminal Lugs (Load)
3. Connect the negative battery cable (BLACK) to the
negative post on the battery (Figure 38).
Before Starting
Generator and Control Panel
CAUTION:
NEVER start the engine with the
main, GFCI or load circuit breakers
in the ON position.
1.
Be sure to disconnect the
.C
.I.
electrical load and switch the main, load and G.F
G.F.C
.C.I.
circuit breakers (Figure 12) to the “OFF” position prior to
starting the engine.
IVE
ST
PO
E
TIV
GA
NE
RY
E
TT
A
B
Figure 38. Battery Connections
Figure 36. Main, GFCI and
Load Circuit Breakers
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 47
DCA-60SSI2 — GENERATOR START-UP PROCEDURE
4. Close all engine enclosure doors (Figure 39).
8.
Once the preheat indicator lights, turn the key to
‘START’ (Figure 43). After the engine cranks,
release the key to ‘RUN’.
Figure 43. Starter Switch (Start)
Figure 39. Engine Enclosure Doors
5.
Check the voltage selection switch (Figure 40) is
at the desired voltage.
9.
Pull the engine throttle lever and turn left until the
lever sets on the knob (Figure 44).
Figure 44. Engine Throttle Lever (Up)
Figure 40. Voltage Selection Switch
6.
Check to see if the engine throttle lever (Figure
41) is pushed in.
10. The generator's frequency meter (Figure 45) displays
the 60 cycle output frequency in HERTZ.
Figure 45. Frequency Meter (Hz)
Figure 41. Engine Throttle Lever
7.
Turn the starter switch to ‘PREHEAT’ (Figure 42)
until the indicator light turns on. The oil pressure
indicator light will initially turn on, but should turn off
once the pressure rises.
Figure 42. Key Switch (Preheat)
11. The generator's voltage meter (Figure 46) displays the
120 VAC in VOLTS. If the voltage is not within the
specified frequency tolerance, use the voltage
adjustment control knob (Figure 47) to increase or
decrease the desired voltage.
Figure 46. Voltage Meter (Volts)
PAGE 48 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — GENERATOR START-UP PROCEDURE
15. The charging ammeter (Figure 51) will indicate if the
battery is properly charged.
Figure 47. Voltage Adjust Control
Knob
12. The ammeter (Figure 48) will indicate zero amps with no
load applied. When a load is applied, this meter will
indicate the amount of current that the load is drawing
from the generator’s alternator.
20
40
0
Figure 51. Charging Ammeter
16. The tachometer (Figure 52) will indicate the speed of
the engine when the generator is operating. Under normal
operating conditions this speed is approximately 1800
RPM’s.
60
75
A
Figure 52. Engine Tachometer
Figure 48. Ammeter (No Load)
13. The engine oil pressure gauge (Figure 49) will indicate
the oil pressure (kg/ cm2) of the engine. Under normal
operating conditions the oil pressure is approximately
25 psi.
17. Turn the MAIN, GFCI and LOAD circuit breakers to
their ON position (Figure 53).
Figure 53. Main and GFCI Circuit Breakers
Figure 49. Oil Pressure Gauge
14. The coolant temperature gauge (Figure 50) will indicate
the coolant temperature. Under normal operating
conditions the coolant temperature is between 165 and
215 degrees fahrenheit.
18. Observe the generator's ammeter (Figure 54) and verify
it reads the anticipated amount of current with respect
to the load. The ammeter will only display a current
reading if the load is in use.
20
40
0
60
75
A
WATER
TEMP
Figure 54. Ammeter (Load)
19. The generator will run until manually stopped or an
abnormal condition occurs.
Figure 50. Coolant Temperature Gauge
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 49
DCA-60SSI2 — GENERATOR SHUT-DOWN PROCEDURE
ENGINE SHUTDOWN
To shutdown the generator, use the following procedure:
1. Switch both the MAIN, GFCI and LOAD circuit breakers
(Figure 55)to the “OFF” position.
EMERGENCY STOP
1. To stop the engine in the event of an emergency, switch
the MAIN, GFCI and LOAD circuit breakers to ‘OFF’
position.
2.
Turn the key switch to ‘STOP’.
Figure 55. Main, GFCI and Load
circuit breakers
2. Turn to the right and press in the engine throttle lever
(Figure 56).
Figure 56. Engine Throttle Lever
3. Let the engine cool by running it for 3-5 minutes with no
load applied.
4.
Turn the key switch to ‘STOP’’ (Figure 57).
Figure 57. Key Switch (OFF)
5.
Remove the load from the UVW terminal strip.
PAGE 50 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
NOTE PAGE
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 51
DCA-60SSIU — MAINTENANCE
General Inspection
Cleaning the Fuel Strainer
Prior to each use, the generator should be cleaned and
inspected for deficiencies. Check for loose, missing or
damaged nuts, bolts or other fasteners. Also check for fuel,
oil, and coolant leaks.
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in gasoline.
Securely fasten the fuel strainer cap so that fuel will not
leak. Check the fuel strainer every 200 hours of operation or
once a month.
Engine Side (Refer to the Engine Instruction Manual)
Air Cleaner
Every 50 hours: Remove air cleaner element and clean heavy
duty paper element with kerosene, or foam element with
liquid detergent and hot water. Wrap foam element in a cloth
and squeeze dry. For heavy duty paper element, wipe
excess kerosene with towel.
The air cleaner is equipped with an indicator. After the dirty
air cleaner has been replaced, press the dust indicator button
to reset the indicator.
Fuel Addition
Add diesel fuel (the grade may vary according to season
and locations). Always pour through the mesh filter.
Removing Water from the Fuel Tank
After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally remove the drain
cock and drain the contents. During cold weather, the more
empty volume inside the tank, the easier it is for water to
condense. This can be reduced by keeping the tank full as
much as possible.
Air Removal
If air enters the fuel injection system of a diesel engine,
starting becomes impossible. After running out of fuel, or
after disassembling the fuel system, bleed the system
according to the following procedure.
To restart after running out of fuel, turn the switch to the
“ON” position for 15-30 seconds. Try again, if needed. This
unit is equipped with an automatic air bleeding system.
Check Oil Level
Check the crankcase oil level prior to each use, or when the
fuel tank is filled. Insufficient oil may cause severe damage
to the engine. Make sure the generator is level. The oil level
must be between the two notches on the dipstick as shown
in Figure 32, page 43.
Replacing Oil Filter
1. Detach the oil filter cartridge with a filter wrench.
2. Apply a film of oil to the gasket for the cartridge.
3. Screw in the cartridge by hand. When the gasket is in
contact with the seal surface, tighten the cartridge one
or two more times by hand.
4. After the oil cartridge has been replaced, the engine oil
will drop slightly. Run the engine for a while and check
for leaks before adding more oil if needed. Clean
excessive oil from engine.
Replacing Fuel Filter
1. Replace the fuel filter cartridge with new one every 400
hours or so.
2. Apply fuel oil thinly over the gasket and hand-tighten
the cartridge into position.
3. Vent any air.
4. Fuel Injection Nozzle
5. Use an injection nozzle tester to check the static injection
starting pressure and the fuel spray conditions.
6. Abnormal fuel consumption will lead to a lowered output
and blackish exhaust smoke. The required injection
starting pressure should be 14.7MPa (150kg/cm2,
2130psi).
Service Daily
If the engine is operating in very dusty or dry grass
conditions, a clogged air cleaner will result. This can lead to
a loss of power, excessive carbon buildup in the combustion
chamber in high fuel consumption.
PAGE 52 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU — MAINTENANCE
Feed Pump Strainer Cleaning
The strainer is incorporated in the feed pump inlet side joint
bolt. Clean the strainer with compressed air and rinse it in
the fuel oil.
Flushing Out Radiator and Replacing Coolant
1. Open both cocks located at the crankcase side and at
the lower part of the radiator and drain coolant. Open
the radiator cap while draining. Remove the overflow
tank and drain.
2. Check hoses for softening and kinks. Check clamps for
signs of leakage.
3. Flush the radiator by running clean tap water through
radiator until signs of rust and dirt are removed. DO
NOT clean radiator core with any objects, such as a
screwdriver.
4. Tighten both cocks and replace the overflow tank.
5. Replace with coolant (see page 44, Table 14 for mixture).
6. Close radiator cap tightly.
CAUTION :
Allow engine to cool when flushing out
radiator. Flushing the radiator while hot will
damage radiator.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 53
DCA-60SSIU — MAINTENANCE
Valve Clearance Check
1. In order to bring No. 1 or No. 4 cylinder to top dead center
in the compression stroke, align the notched line on the
crank pulley with TDC mark on the timing gear case
cover.
3. Remove the timing check hole cover at the front of
injection pump to check the alignment between the
pointer “a” on the injection pump gear lock plate and the
projected area mark “b” on the timing gear case.
4. If “a” and “b” are in alignment, the timing is set correctly.
If not, follow nos. 1-3 until the “a” and “b” are aligned.
2. Do the adjustment on the circle marked valves in the
below table where No. 1 cylinder is at the center in the 5. Reversely turn the crankshaft pulley counterclockwise
viewed at the engine front about 30o crank angle.
compression stroke.
3. After adjustment started from either piston top center, 6. Remove No. 1 injection pipe from the engine.
turn the crankshaft 360o to align the notched line with 7. Remove the injection pump No. 1 delivery valve holder,
the TDC mark to do the adjustment again on the
delivery valve and spring and reinstall the delivery valve
remaining valve. See Table 16 and Figure 55 for valve
holder on the original place.
arrangement.
8. Delivery valve holder tightening torque:
39~44Nm(29~33lbft.)
Injection Timing Check and Adjustment
9. Slowly turn the crankshaft pulley clockwise and at the
1. Bring No. cylinder to the top dead center on the
compression stroke.
same time continue to feed the fuel with pumping the
Feed pump. When the fuel stop to flow out from No. 1
delivery valve holder, stop pumping.
2. Turn the crankshaft pulley clockwise (viewed at engine
front) and align the notched line on the crank pulley with 10. Observe and make sure which mark (injection starting
the TDC mark on the timing gear case cover.
angle line) on the timing gear case cover is aligning with
the notched line on the crank pulley.
11. The timing line shows the injection starting crank angle
of the engine.
12. The injection starting crank angle should be at the 14o
timing mark.
Table 15. Valve Adustment
(I=Inlet; E=Exhaust)
Cylinder No.
Figure 58. Valve Adjustment
NOTE:
Take necessary precautions to prevent dust and
foreign particles in the pump interior when timing
adjustments are made.
1
2
Valve Arrangement
I
E
I
When No. 1 is at top
dead center in the
compression stoke
X
X
X
When No. 4 is at top
dead center in the
compression stroke
3
E
I
4
E
I
E
O
O
X
O
O
PAGE 54 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSIU — MAINTENANCE
INSPECTION / MAINTENANCE
ENGINE
GENERATOR
10 Hrs
DAILY
Check Engine Fluid Levels
X
Check Air Cleaner
X
Check Battery Acid Level
X
Check Fan Belt Condition
X
Check for Leaks
X
Check for Loosening of Parts
X
250 Hrs
Replace Engine Oil and Filter *1
X
Clean Air Filter
X
Drain Bottom of Fuel Tank
X
Clean Unit, Inside and Outside
X
500 Hrs
Change Fuel Filter *2
X
Clean Radiator and Check Coolant Protection
Level
X
1000 Hrs
Replace Air Filter Element
X
Change Corrosion Resistor
X
Check all Hoses and Clamps
X
Clean Inside of Fuel Tank
X
Measure Insulation Resistance Over 3M ohms
X
*1 Replace engine oil anf filter at 100 hours, first time only.
*2 Replace fuel filter at 250 Hours, first time only.
Generator Storage
For storage of the generator for over 30 days, the following
is required:
y Fill the fuel tank completely.
y Completely drain the oil from the crankcase and refill
with fresh oil.
y Clean all external parts of the generator with a cloth.
y Cover the generating set and store in a clean, dry place.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 55
DCA-60SSI2 — GENERATOR WIRING DIAGRAM
PAGE 56 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — ENGINE WIRING DIAGRAM
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 57
DCA-60SSI2 — TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper
handling and maintenance inspections, but in the event of a
breakdown, use the tables shown for
diagnosis based on the Engine Troubleshooting (Table 16). If
the problem cannot be remedied, consult our company's
business office or service plant.
TABLE 16. ENGINE TROUBLESHOOTING
SYMPTOM
Engine does not start.
POSSIBLE PROBLEM
SOLUTION
No fuel?
Replenish fuel.
Air in the fuel system?
Bleed system.
Water in the fuel system?
Remove water from fuel tank.
Fuel pipe clogged?
Clean fuel pipe.
Fuel filter clogged?
Clean or change fuel filter.
Excessively high viscosity of fuel
or engine oil at low temperature?
Use the specified fuel or engine oil.
Fuel with low cetane number?
Use the specified fuel.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Incorrect injection timing?
Adjust.
Fuel cam shaft worn?
Replace.
Injection nozzle clogged?
Clean injection nozzle.
Injection pump malfunctioning?
Repair or replace.
Seizure of crankshaft, camshaft,
piston, cylinder liner or bearing?
Repair or replace.
Compression leak from cylinder?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
Improper valve timing?
Correct or replace timing gear.
Piston ring and liner worn?
Replace.
Excessive valve clearance?
Adjust.
Starter malfunctioning?
Repair or replace.
Wiring disconnected?
Connect wiring.
Starter does not run.
PAGE 58 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — TROUBLESHOOTING (ENGINE)
TABLE 16. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
Engine revolution is not smooth.
Either white or blue exhaust gas
is observed.
Either black or dark gray exhaust
gas is observed.
Deficient output.
POSSIBLE PROBLEM
SOLUTION
Fuel filter clogged or dirty?
Clean or change.
Air cleaner clogged?
Clean or change.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Injection pump malfunctioning?
Repair or replace.
Incorrect nozzle opening
pressure?
Adjust.
Injection nozzle stuck or
clogged?
Repair or replace.
Fuel over flow pipe clogged?
Clean.
Governor malfunctioning?
Repair.
Excessive engine oil?
Reduce to the specified level.
Piston ring and liner worn or
stuck?
Repair or replace.
Incorrect injection timing?
Adjust.
Deficient compression?
Adjust top clearance.
Overload?
Lessen the load.
Low grade fuel used?
Use the specified fuel.
Fuel filter clogged?
Clean or change.
Air cleaner clogged?
Clean or change.
Deficient nozzle injection?
Repair or replace the nozzle.
Incorrect injection timing?
Adjust.
Engine's moving parts seem to
be seizing?
Repair or replace.
Uneven fuel injection?
Repair or replace the injection pump.
Deficient nozzle injection?
Repair or replace the nozzle.
Compression leak?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 59
DCA-60SSI2 — TROUBLESHOOTING (GENERATOR/ENGINE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, use the tables shown for diagnosis based on the Engine and Radiator Troubleshooting (Table 7). If the problem
cannot be remedied, consult our company's business office or service plant.
TABLE 17. GENERATOR TROUBLESHOOTING
SYMPTOM
No Voltage Output
Low Voltage Output
High Voltage Output
Circuit Breaker Tripped
POSSIBLE PROBLEM
SOLUTION
AC Voltmeter defective?
Check output voltage using a voltmeter.
Is wiring connection loose?
Check wiring and repair.
Is AVR defective?
Replace if necessary.
Defective Rotating Rectifier?
Check and replace.
Is engine speed correct?
Turn engine throttle lever to "High".
Is wiring connections loose?
Check wiring and repair.
Defective AVR?
Replace if necessary.
Is wiring connections loose?
Check wiring and repair.
Defective AVR?
Replace if necessary.
Short Circuit in load?
Check load and repair.
Over current?
Confirm load requirements and reduce.
Defective circuit breaker?
Check and replace.
Over current Relay actuated?
Confirm load requirement and replace.
PAGE 60 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
NOTE PAGE
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 61
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial
number range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model
number or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #,
*
+, or %, belong to the same assembly or kit.
Note: If more than one of the same reference number is
listed, the last one listed indicates newest (or latest)
part available.
PAGE 62 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 — SUGGESTED SPARE PARTS
DCA-60SSI2 W/ISUZU 6BG1 DIESEL ENGINE
1 TO 3 UNITS
Qty.
P/N
Description
1 ......... 0601805869 ......... CIRCUIT BREAKER
1 ......... 0601820671 ......... AUTOMATIC VOLTAGE REGULATOR
1 ......... 0601840073 ......... RHEOSTAT VOLTAGE REGULATOR
1 ......... 0601840121 ......... KNOB REHOSTAT
1 ......... 0602013901 ......... RADIATOR HOSE, UPPER
1 ......... 0602013160 ......... RADIATOR HOSE, LOWER
5 ......... 1878100753 ......... OIL FILTER
5 ......... X132400240 ........ FUEL FILTER
5 ......... 0602040193 ......... ELEMENT, AIR
1 ......... 0602122200 ......... UNIT OIL PRESSURE
1 ......... 0602123204 ......... UNIT WATER PRESSURE
1 ......... 0601810244 ......... BULB, ALARM LAMP
1 ......... 0601808507 ......... TRANSDUCER WATT METER
1 ......... 8972322520 ......... FAN BELT
1 ......... 1823100080 ......... STARTER SWITCH
3 ......... KEYISUZUF ........ KEY, STARTER SWITCH
NOTE
Part number on this Suggested Spare
Parts list may supercede/replace the
P/N shown in the text pages of this
book.
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 63
DCA-60SSI2 --- GENERATOR ASSY.
GENERATOR ASSY.
PAGE 64 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- GENERATOR ASSY.
GENERATOR ASSY.
NO.
PART NO.
1
8081000302
1
8081000312
1-1
1-2
8051070003
1-3
0010310030
0012110035
1-4
030210250
1-5
8041611004
1-6
8041015003
1-7
0010310025
1-8
0042610000
1-6
8001026013
1-10 0601821349
1-11 0601822601
1-12 8001020004
1-13 8001020504
1-14 0010108020
1-15 0040008000
1-16 0601000209
1-17 0070806309
1-17 0071906310
2
8051614003
3
8051653004
4
012010030
5
0042510000
6
8081340503
7
0845041904
8
8041315202
8
8041315202
9
8041350013
10
0010308065
11
0042608000
12
031108160
13
0010108025
14
0040008000
15
0041208000
16
0601000003
17
8041310014
8041310024
18
8041312004
8041310014
ITEM
QTY.
REMARKS
ROTOR ASSY. ................................ 1 ........... UP TO S/N3621172
ROTOR ASSY. ................................ 1 ........... FROM S/N3621173~
FIELD ASSY.
1
FAN
1
HEX. HEAD BOLT ........................... 8 ........... UP TO S/N3621172
HEX. HEAD BOLT ........................... 8 ........... S/N3621173~
LOCK WASHER .............................. 8 ........... REPLACES 0042510000
COUPLING DISK
4
BALANCING PLATE
1
HEX. HEAD BOLT ........................... 6 ........... REPLACES 0010310025
LOCK WASHER
6
SET PLATE RECTUFER
1
RECTIFIER ..................................... 2 ............ PT3610
SURGER ABSORBER .................... 1 ............ ERZM14JK621A
INSULATOR WASHER
1
INSULATOR WASHER
1
LOCK WASHER
4
LOCK WASHER
4
BALANCING WEIGHT KIT
1
BEARING ........................................ 1 ........... 6309DU;UP TO S/N3621172
BEARING ........................................ 1 ........... 6310DDU; S/N3621173~
COUPLING RING
1
REAMER BOLT
2
HEX. HEAD BOLT ........................... 7 ........... REPLACES 0012110030
LOCK WASHER .............................. 9 ........... REPLACES 0042510000
STRATOR ASSY.
1
GROMMET
2
END BRACKET .............................. 1 ........... UP TO S/N362172
END BRACKET .............................. 1 ........... S/N362173~
FIELD ASSY. EXCITER
1
HEX. HEAD BOLT
4
LOCK WASHER
4
PLAIN WASHER ............................. 6 ........... REPLACES 0041208000
HEX. HEAD BOLT
6
LOCK WASHER
6
PLAIN WASHER
6
WAVE WASHER .............................. 1 ........... BWW6309; UP TO S/N3621172
COVER, BEARING ......................... 1 ........... UP TO S/N3621172
COVER, BEARING ......................... 1 ........... S/N3621173~
GASKET, BEARING ....................... 1 ........... UP TO S/N3621173
GASKET, BEARING ....................... 1 ........... S/N3621173~
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 65
DCA-60SSI2 --- GENERATOR ASSY.
GENERATOR ASSY.
PAGE 66 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- GENERATOR ASSY.
GENERATOR ASSY.
NO.
PART NO.
19
8041331014
20
0105050616
21
8001333003
22
0010106030
23
0040006000
24
952404470
25
015091025
26
030210250
27
8051332003
8051332014
28
0605000010
29
0030012000
0040012000
ITEM
QTY.
REMARKS
COVER, END BRACKET
1
HEX. HEAD BOLT ........................... 8 ........... REPLACES 0017106012
COVER, END BRACKET
1
HEX. HEAD BOLT
2
LOCK WASHER
2
PLAIN WASHER ............................ 2 ........... REPLACES 0041206000
HEX. HEAD BOLT ........................... 6 ........... REPLACES 0010310025
LOCK WASHER .............................. 6 ........... REPLACES 0042510000
COVER, FAN ................................... 1 ........... UP TO S/N3621172
COVER, FAN ................................... 1 ........... S/N3621173~
RUBBER SUSPENSION
HEX. NUT
4
LOCK WASHER
4
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 67
DCA-60SSI2 --- CONTROL BOX ASSY.
CONTROL BOX ASSY.
PAGE 68 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO.
PART NO.
1
8081812502
B4214000002
2
0601801143
3
0027104010
4
0601823860
5
0027104016
6
0601820628
0601820671
7
0027105012
8
0601820853
0601820892
9
0027104016
10
0602200405
11
0027106016
12
0601823706
13
0027104016
14
0601805352
14
0601805869
15
0021004020
0040004000
031104080
16
M1923100004
17
0020004010
18
8051839504
19
0021003010
20
0017106016
020106050
21
7451822503
7451822513
22
0601800460
23
0601800784
24
0601801040
25
0601800212
26
0601801041
27
0601810072
0601810261
28
0601840073
29
0601840121
ITEM
QTY.
REMARKS
CONTROL BOX ............................................ 1 ....... UP TO S/N3646800
CONTROL BOX ............................................ 1 ....... S/N3646801~
CURRENT TRANSFORMER, AMMETER ..... 3 ....... CT-3.5MR 100/5A
MACHINE SCREW
6
RELAY UNIT ................................................. 2 ....... MSA9013
MACHINE SCREW
4
AUTOMATIC VOLTAGE REGULATOR ........... 1 ....... NTA5A2D; UP TO S/N3656070
AUTOMATIC VOLTAGE REGULATOR ........... 1 ....... NTA5A2DB; S/N3656071~
MACHINE SCREW
4
OVER CURRENT RELAY ............................. 1 ....... THK20KP; UP TO S/N3656070
OVER CURRENT RELAY ............................. 1 ....... THN20HZKP; S/N3656071~
MACHINE SCREW
4
EMERGENCY RELAY .................................. 1 ....... ISUZU 1825500730
MACHINE SCREW
4
RELAY .......................................................... 1 ....... HE1AAHE1112 DC24V
MACHINE SCREW
2
CIRCUIT BREAKER ..................................... 1 ....... KM203150AT; UP TO S/N3646800
CIRCUIT BREAKER ..................................... 1 ....... NY203A 150AT; S/N3646801~
MACHINE SCREW
4
LOCK WASHER
4
PLAIN WASHER ........................................... 4 ....... REPLACES 0041204000
SELECTOR SWITCH .................................... 1 ....... REPLACES 8010153104
MACHINE SCREW ....................................... 4 ....... REPLACES 0021104010
BRACKET, SELECTOR SWITCH
1
MACHINE SCREW
4
HEX. HEAD BOLT
2
HEX. NUT ..................................................... 2 ....... REPLACES 0030006000
CONTROL PANEL ......................................... 1 ....... UP TO /SN3646800
CONTROL PANEL ......................................... 1 ....... S/N36463801~
FREQUENCY METER .................................. 1 ....... PAK60 220V 45~65Hz
AC AMMETER .............................................. 1 ....... PSK60 0~100A -~200A
CHANGE-OVER SWITCH, AMMETER ......... 1 ....... SL2AS
AC VOLTMETER ........................................... 1 ....... REPLACES 0601800217 PCK60 0~600V
CHANGE-OVER SWITCH, VOLTMETER ...... 1 ....... SL2VS
PILOT LAMP ................................................. 1 ....... LP132DC 220V
BULB ............................................................. 1 ....... T13
VOLTAGE REGULATOR ................................ 1 ....... RA20A2SE102BJ 2W 1k OHM
KNOB
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 69
DCA-60SSI2 --- CONTROL BOX ASSY.
CONTROL BOX ASSY.
PAGE 70 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO.
PART NO.
30
31
32
33
34
35
36
37
38
39
40
3331824003
0027105016
0030005000
0805001304
0845056404
031108160
020108060
0027105010
8081814503
0017106016
8081814604
0017106016
011208025
ITEM
QTY.
REMARKS
STOPPER, CONTROL PANEL
1
MACHINE SCREW
2
HEX. NUT
2
SET SCREW ................................................. 2 ....... UP TO S/N3655377
SET SCREW ................................................. 2 ....... S/N3655378~
PLAIN WASHER ........................................... 2 ....... REPLACES 0041208000
HEX. NUT ..................................................... 2 ....... REPLACES 0030008000
MACHINE SCREW
4
COVER
1
HEX. HEAD BOLT
11
SIDE PANEL
1
HEX. HEAD BOLT
4
HEX. HEAD BOLT ......................................... 4 ....... REPLACES 0017108025
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 71
DCA-60SSI2 ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
PAGE 72 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
1
0602000100
ENGINE ........................................... 1 ......... ISUZU 6BD1; UP TO S/N3656070
B4924200114 ENGINE ........................................... 1 ......... ISUZU A6BD1; S/N3656071~
2
0602010802
RADIATOR ....................................... 1 ......... H190110000
3
0017108020
HEX. HEAD BOLT
6
4
0602013901
RADIATOR HOSE ............................ 1 ......... B400008
5
0602013160
RADIATOR HOSE ............................ 1 ......... B400007
6
0602014302
HOSE BAND
3
7
06020143303 HOSE BAND
1
8
0602040090
AIR CLEANER ................................. 1 ......... FWG088006
0602040193
ELEMENT, AIR CLEANER ............... 1 ......... P104972
9
0602040690
DUST INDICATOR ............................ 1 ......... RBX002252
10
0602040598
BAND, AIR CLEANER ..................... 2 ......... AAH008263
11
0017108020
HEX. HEAD BOLT
4
12
7452032303
HOSE, AIR CLEANER
1
13
0605515008
HOSE BAND
2
14
0602041106
ELEMENT, OIL FILTER ................... 1 ......... 1878100751
15
0602042106
ELEMENT, FUEL FILTER ................ 1 ......... 988511911;UP TO S/N3656070
X132400240
ELEMENT, FUEL FILTER ................ 1 ......... S/N3656071~; REPLACES 1132400791
16
3345112403
ENGINE FOOT
1
17
3345112503
ENGINE FOT
1
18
0010710025
HEX. HEAD BOLT
7
19
0030610000
HEX. NUT
1
20
0040010000
LOCK WASHER
8
21
060500009
RUBBER SUSPENSON
4
22
0040012000
LOCK WASHER
4
23
0030112000
HEX. NUT
4
24
1819001931
ENGINE STEOPPER ...................... 1 ......... REPLACES 0602210803 & 1819000161
25
7452215104
BRACKET, ENGINE STOPPER
1
26
0027106016
MACHIEN SCREW
3
27
00171080220 HEX. HEA BOLT
2
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 73
DCA-60SSI2 ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
PAGE 74 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 ENGINE AND RADIATOR ASSY.
ENGINE AND RADIATOR ASSY.
NO.
PART NO.
ITEM
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
74522051104
0805013704
0805014204
3362054104
3362051003
0802024004
0802010204
7452053104
0605515158
0017108020
0030008000
0845031303
0802081104
7452082504
0017108020
0017106025
0199500470
0199500175
0193602000
0605515013
0193100950
0605515007
0193800850
0605515019
7452220404
8970209410
QTY.
REMARKS
DRIAN JOINT
1
PACKING, OIL PAN SIDE
1
PACKING
1
JOINT BOLT
1
DRIAN GOINT
1
PACKING
1
PLUG1
DRINAG HOSE
1
HOSE BAND
2
HEX. HEAD BOLT
2
HEX. NUT
2
RESERVE TANK
1
CAP, RESERVE TANK
1
BRAKET, RESERVE TANK
1
HEX. HEAD BOLT
2
HEX. HEAD BOLT
1
HOSE
1
HOSE
1
HOSE
1
HOSE BAND
4
HOSE
1
HOSE BAND
1
HOSE
1
HOSE BAND
1
EARTH CABLE
1
FILTER ............................................. 1 ......... REPLACES 9581541441
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 75
DCA-60SSI2 --- ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
PAGE 76 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
1
7452111103
OPERATING PANEL
1
2
7452142014
SLIDE BAR
1
3
0601840190
KNOB ............................................... 1 ......... REPLACES 0805012904
4
020108060
HEX. NUT ........................................ 1 ......... REPLACES 0036003000
5
7452140504
BRACKET, GOVERNOR ROD
1
6
020108060
HEX. NUT ........................................ 2 ......... REPLACES 0030008000
7
0605010503
SNAP PIN
1
8
1823100080
STARTER SWITCH .......................... 1 ......... REPLACES 06021000004
KEYISUZUF KEY, STARTER SWITCH
1
9
1814020031
PREHEAT LAMP .............................. 1 ......... REPLACES 9825300430
10
0602120054
TACHOMETER ................................. 1 ......... 25000KX4110
11
0602120154
CABLE, TACHOMETER ................... 1 ......... 621000KA6710L=1150
12
0602122060
OIL PRESSURE GAUGE ................. 1 ......... 4200KX1410
13
0602122200
UNIT, OIL PRESSURE ..................... 1 ......... 53000AC0101
14
0131300000
STREET SOCKET ........................... 1 ......... UP TO S/N3623457
14
9099022380
STREET SOCKET ........................... 1 ......... S/N3623458~; REPLACES 0603306350
15
0602123061
WATER TEMPERATURE GAUGE .... 1 ......... 51400KA1200
16
0602123204
UNIT, WATER TEMPERATURE ........ 1 ......... 41400KA1200
17
0602121052
CHARGING AMMETER GAUGE ..... 1 ......... 43000KV0300
18
0602103091
ALARM LAMP .................................. 2 ......... REPLACES 0602103090
0601810244
BULB
2
19
0601830420
SWITCH, LAMP CHECK .................. 1 ......... SB61A
20
0601810120
PANEL LIGHT .................................. 1 ......... DL31000
0601810214
BULB ................................................ 1 ......... REPLACES 0601810201
21
0040520000
TOOTHED LOCK WASHER
1
22
0601830710
SWITCH, PANEL LIGHT .................. 1 ......... S301T
23
011008040
HEX. HEAD BOLT ............................ 2 ......... REPLACES 0010008040
0040008000
LOCK WASHER
2
031108160
PLAIN WASHER ............................... 2......... REPLACES 0041208000
24
011008020
HEX. HEAD BOLT ............................. 2......... REPLACES 0017108020
25
8085312103
SUPPORT LEG
1
26
0017110025
HEX.HEAD BOLT
2
27
011208025
HEX. HEAD BOLT ............................ 2 ......... REPLACES 0017108025
020108060
HEX. NUT ........................................ 2 ......... REPLACES 0030008000
28
7452183004
LINK, GOVERNOR ROD
1
29
0105091025
HEX. HEAD BOLT ............................ 1 ......... REPLACES 0010010025
30
031110160
PLAIN WASHER .............................. 2 ......... REPLACES 0041210000
31
020310080
HEX. NUT ........................................ 1 ......... REPLACES 0030010000
32
7452182014
GOVERNOR ROD
1
33
7452152004
GOVERNOR ROD
1
34
0602180106
BALL JOINT
2
35
020108060
HEX. NUT ........................................ 2 ......... REPLACES 0030008000
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 77
DCA-60SSI2 --- ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
PAGE 78 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
NO.
PART NO.
ITEM
QTY.
REMARKS
36
0602180108
BALL JOINT
1
37
020106050
HEX. NUT ........................................ 3 ......... REPLACES 0030006000
38
952404470
PLAIN WASHER .............................. 1 ......... REPLACES 0041206000
39
8111860103
SET BOARD, OUPUT TERMINAL 1
40
0801830204
OUTPUT TERMINAL
5
41
0801830704
HEX. HEAD BOLT
5
42
0039312000
HEX. NUT
10
43
0040012000
LOCK WASHER
15
44
0041412000
PLAIN WASHER
20
45
011208030
HEX. HEAD BOLT ............................ 5 ......... REPLACES 0017108030
46
8081865504
COVER, OUTPUT TERMINAL
1
47
0605010051
HINGE
2
48
0027103016
MACHINE SCREW
12
0207003000
HEX. NUT
6
49
0017106016
HEX. HEAD BOLT
2
50
0601811034
RECEPTACLE .................................. 2 ......... REPLACES 0601812565; CS6369 250V 50A;
51
0601811030
RECEPTACLE .................................. 2 ......... UP TO S/N3627236; 5-20R 125V0 20A
0601812598
RECEPTACLE .................................. 1 ......... S/N3627237~;GF53 OEM 125V 20A
52
0027103010
MACHINE SCREW
10
0207003000
HEX. NUT ...................................... 10 ......... REPLACES 0030003000
S8413
PLAIN WASHER ............................ 10 ......... REPLACES 0041203000
53
0601805306
CIRCUIT BREAKER ........................ 2 ......... UP TO S/N3627236; KM51 265V 40A
0601804887
CIRCUIT BREAKER ........................ 2 ......... S/N3627237~;REPLACES 0601805313
KM51 265V 20A
54
0601805840
CIRCUIT BREAKER ........................ 3 ......... KM52 265V 50A
55
8081816303
BRACKET, CIRCUIT BREAKER
1
0222100200
RUBBER SHEET
1
56
0017106016
HEX. HEAD BOLT
2
57
8085182004
RUBBER COVER
1
59
011206020
HEX. HEAD BOLT ............................ 6 ......... REPLACES 0017106020
60
8081865303
COVER, RECEPTACLE
1
61
12212045
HEX. HEAD BOLT ............................ 2 ......... REPLACES 0010012045
62
031112230
PLAIN WASHER .............................. 4 ......... REPLACES 0041612000
63
0805009804
RUBBER WASHER
2
64
0030012000
HEX. NUT
2
65
0601820015
RECTIFER ....................................... 4 ......... IS2762
66
0601802133
FUSE ............................................... 1 ......... 5A
67
0601851780
GROMMET ...................................... 2 ......... S/N3700638~
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 79
DCA-60SSI2 --- BATTERY ASSY.
BATTERY ASSY.
PAGE 80 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- BATTERY ASSY.
BATTERY ASSY.
NO.
PART NO.
1
0168409541
2
0805003904
3
0805004004
4
0805002904
5
031108160
6
0040008000
7
0037808000
8
0215260065
9
0211160180
10
0215860100
11
0602220310
020800800
12
0602220311
0208008000
13
0845040414
14
0845041304
ITEM
QTY.
REMARKS
BATTERY ......................................... 2 ......... 95E41R
BATTERY SHEET
2
BATTERY BAND
2
BATTERY BOLT
4
PLAIN WASHER .............................. 4 ......... REPLACES 0041208000
LOCK WASHER
4
WING NUT
4
BATTERY CABLE
1
BATTERY CABLE
1
BATTERY CABLE
1
TERMINAL ASSY (+)
2
WING NUT
2
TERMINAL ASSY (-)
2
WING NUT
2
TERMINAL CAP
2
TERMINAL CAP
2
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 81
DCA-60SSI2 --- MUFFLER ASSY.
MUFFLER ASSY.
PAGE 82 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- MUFFLER ASSY.
MUFFLER ASSY.
NO.
PART NO.
1
8082330303
2
1141450690
3
9091103100
4
3802311122
5
012210020
6
7452330303
7
B4334200404
8
011008035
9
031108160
10
0040008000
11
0030008000
12
1382320003
13
011208030
14
031108160
15
020108060
16
3342354104
17
3342354004
18
3342328104
19
031108160
20
020108060
21
3342359004
22
011208025
ITEM
QTY.
REMARKS
EXHAUST PIPE
1
GASKET .......................................... 1 ......... REPLACES 9221160010
HEX. NUT ........................................ 6 ......... REPLACES 9091103100
MUFFLER
1
HEX. HEAD BOLT ............................ 4 ......... REPLACES 0017110020
EXHAUST PIPE
1
GASKET
1
HEX. HEAD BOLT ............................ 4 ......... REPLACES 0010108035
PLAIN WASHER .............................. 4 ......... REPLACES 0041208000
LOCK WASHER
4
HEX. NUT
4
PIPE BAND
1
HEX. HEAD BOLT ............................ 1 ......... REPLACES 0010008030
PLAIN WASHER .............................. 1 ......... REPLACES 0041208000
HEX. NUT ........................................ 1 ......... REPLACES 0030008000
COVER
1
COVER
2
PIPE CLAMPER
1
PLAIN WASHER .............................. 2 ......... REPLACES 0041208000
HEX. NUT ........................................ 4 ......... REPLACES 0030008000
COVER SHEET
2
HEX. HEAD BOLT ............................ 4 ......... REPLACES 0017108025
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 83
DCA-60SSI2 --- FUEL TANK ASSY.
FUEL TANK ASSY.
PAGE 84 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- FUEL TANK ASSY.
FUEL TANK ASSY.
NO.
PART NO.
1
1-1
1-2
1-3
1-4
2
3
4
5
6
7
8
9
10
11
12
13
14
7455510303
0810105004
0810105400
0193100255
0605515079
7455523304
0805003414
011008020
0207008000
020108060
0222100200
0131906000
0191301150
0191300670
0605515109
0845032204
0845047504
0150000018
0802011104
ITEM
QTY.
REMARKS
FUEL TANK
1
CAP, FUEL TANK
1
FUEL FILTER
1
FUEL GAUGE HOSE
1
HOSE BAND
2
TANK BAND
2
PAD, TANK BAND
4
HEX. HEAD BOLT ............................ 2 ......... REPLACES 0017108020
HEX. NUT ........................................ 2 ......... REPLACES 0207008000
HEX. NUT ........................................ 2 ......... REPLACES 0030008000
TANK SHEET
4
CAP
1
SUCTION HOSE
1
RETURN HOSE
1
HOSE BAND
4
DRAIN JOINT .................................. 1 ......... UP TO S/N3653118
DRAIN JOINT .................................. 1 ......... S/N3653119~
O RING
1
PLUG
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 85
DCA-60SSI2 --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
UP TO S/N3656070
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO
INDICATE COLOR OF UNIT:
1-ORANGE
5 -BLACK
2-WHITE
6 -CATERPILLAR YELLOW
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 86 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
NO.
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
22
23
24
25
26
7455111112
7455116004
0017108020
7455116504
0017108020
7455121012
7455121022
7455109203
0017108020
0800251201
0027106016
7455125503
7455109304
0017108020
7455125304
00171080220
3385155104
0017106020
7455125104
7455109404
0017108020
7455125704
7455109504
0017108020
7455132013
B4434300003
7455132213
B4434300103
0010114040
0030014000
0040014000
0041214000
0010124040
0030014000
0040014000
0041214000
0010112030
0040012000
0041212000
7455141122
B4444000102
B4444000112
7455109603
0017108020
7455155003
B4444300203
7455109713
ITEM
QTY.
REMARKS
BASE
1
FLOOR PANLE
1
HEX. HEAD BOLT
12
COVER
1
HEX.HEAD BOLT
2
FRONT FRAME ................................... 1 ............UP TO S/N3656070
FRONT FRAME ................................... 1 ............S/N3656071~
ACOUSTIC SHEET
1
HEX. HEAD BOLT
6
FILLER COVER
1
MACHINE SCREW
2
COVER, FRONT FRAME
1
ACOUSTIC SHET
1
HEX. HEAD BOLT
16
COVER, FRONT FRAME
1
HEX. HEAD BOLT
12
COVER ................................................. 2 ............UP TO S/N3656070
HEX. HEAD BOLT ................................ 8 ............UP TO S/N3656070
COVER, FRONT FRAME
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT
4
COVER, FRONT FRAME
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT
4
CENTER FRAME ................................. 1 ............UP TO S/N3656070
CENTER FRAME ................................. 1 ............S/N3656071~
CENTER FRAME ................................. 1 ............UP TO S/N3656070
CENTER FRAME ................................. 1 ............S/N3656071~
HEX. HEAD BOLT ................................ 8 ............UP TO S/N3656070
HEX. NUT ............................................. 8 ............UP TO S/N3656070
LOCK WASHER ................................... 8 ............UP TO S/N3656070
PLAIN WASHER ................................... 16 ..........UP TO S/N3656070
HEX. HEAD BOLT ................................ 8 ............S/N3656071~
HEX. NUT ............................................. 1 ............S/N3656071~
LOCK WASHER ................................... 8 ............S/N3656071~
PLAIN WASHER ................................... 9 ............S/N3656071~
HEX. HEAD BOLT
10
LOCK WASHER
10
PLAIN WASHER
10
REAR FRAME ...................................... 1 ............UP TO S/N3656070
REAR FRAME ...................................... 1 ............S/N3656071 TO 3700637
REAR FRAME ...................................... 1 ............S/N3700638~
ACOUSTIC SHEET
1
HEX. HEAD BOLT
4
COVER, REAR FRAME ....................... 1 ............UP TO S/N3656070
COVER, REAR FRAME ....................... 1 ............S/N3656071~
ACOUSTIC SHEET
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 87
DCA-60SSI2 --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
UP TO S/N3656070
ADD THE FOLLOWING DIGITS AFTER THE PART NUMBER
WHEN ORDERING ANY PAINTED PANEL TO
INDICATE COLOR OF UNIT:
1-ORANGE
5 -BLACK
2-WHITE
6 -CATERPILLAR YELLOW
3 -SPECTRUM GRAY 7 -CATO GOLD
4 -SUNBELT GREEN 8 -RED
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 88 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
NO.
PART NO.
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
0010108040
0040008000
0041208000
7455143113
B4444200203
B4444200213
3805147104
0021006020
0030006000
0040006000
0041206000
0845028303
0845047204
0017108025
7455161012
7455109803
0017108020
7455165004
7455109904
0017108020
8085181202
8085181212
8085181222
0010108055
0040008000
0041208000
7455171413
B4454000703
B4454000713
7455105104
B4494100104
7455171513
B4454000803
B4454000813
7455105204
B4494100204
7455171613
B4454000903
B4454000913
7455105304
B4494300204
7455171723
B4454001003
B4454001013
7455105414
B4494300304
ITEM
QTY.
REMARKS
HEX. HEAD BOLT
8
LOCK WASHER
8
PLAIN WASHER
8
DOOR, REAR FRAME ......................... 1 ............UP TO S/N3656070
DOOR, REAR FRAME ......................... 1 ............S/N3656071 TO 3700637
DOOR, REAR FRAME ......................... 1 ............S/N3700638~
WINDOW PLATE
1
MACHINE SCREW
6
HEX. NUT
6
LOCK WASHER
6
PLAIN WASHER
6
HINGE .................................................. 2 ............UP TO S/N3656070
HINGE .................................................. 2 ............S/N656071~
HEX. HEAD BOLT
4
ROOF PANEL
1
ACOUSTIC SHEET
1
HEX. HEAD BOLT
16
GUIDE PANEL, AIR
2
ACOUSTIC SHEET
2
HEX. HEAD BOLT
8
SPLASHER PANEL .............................. 1 ............UP TO S/N3627236
SPLASHER PANEL .............................. 1 ............S/N3627237 TO 3700637
SPLASHER PANEL .............................. 1 ............S/N3700638~
HEX. HEAD BOLT
6
LOCK WASHER
6
PLAIN WASHER
6
SIDE DOOR ......................................... 1 ............UP TO S/N3656070
SIDE DOOR ......................................... 1 ............S/N3656071 TO 3700637
SIDE DOOR ......................................... 1 ............S/N3700638~
ACOUSTIC SHEET ............................. 1 ............UP TO S/N3656070
ACOUSTIC SHEET ............................. 1 ............S/N3656071~
SIDE DOOR ......................................... 1 ............UP TO S/N3656070
SIDE DOOR ......................................... 1 ............S/N3656071 TO 3700637
SIDE DOOR ......................................... 1 ............S/N3700638~
ACOUSTIC SHEET ............................. 1 ............UP TO S/N3656070
ACOUSTIC SHEET ............................. 1 ............S/N3656071~
SIDE DOOR ......................................... 1 ............UP TO S/N3656070
SIDE DOOR ......................................... 1 ............S/N3656071 TO 3700637
SIDE DOOR ......................................... 1 ............S/N3700638~
ACOUSTIC SHEET ............................. 1 ............UP TO S/N3656070
ACOUSTIC SHEET ............................. 1 ............S/N3656071~
SIDE DOOR ......................................... 1 ............UP TO S/N3656070
SIDE DOOR ......................................... 1 ............S/N3656071 TO 3700637
SIDE DOOR ......................................... 1 ............S/N3700638~
ACOUSTIC SHEET ............................. 1 ............UP TO S/N3656070
ACOUSTIC SHEET ............................. 1 ............S/N3656071~
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 89
DCA-60SSI2 --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
UP TO S/N3656070
PAGE 90 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- ENCLOSURE ASSY.
ENCLOSURE ASSY.
NO.
PART NO.
43
44
45
47
48
49
69
70
71
72
73
0845028203
0845046904
0845028304
0845047004
0017108025
0601850097
0845031504
6360510003
0600500090
0021106020
0825007362
0221806015
B4444800004
7455109713
B4444800104
7455109713
0207006000
ITEM
QTY.
REMARKS
HINGE .................................................. 4 ............UP TO S/N3656070
HINGE .................................................. 4 ............S/N3656071~
HINGE .................................................. 4 ............UP TO S/N3656070
HINGE .................................................. 4 ............S/N3656071~
HEX. HEAD BOLT
16
RUBBER CUSHION
8
CAP
10
EMBLEM ............................................... 2 ............UP TO S/N3660480
EMBLEM ............................................... 2 ............S/N3660481~
MACHINE SCREW
4
DOOR HANDLE ................................... 5 ............S/N3656071~
MACHINE SCREW .............................. 20 ..........S/N3656071~
DUCT ................................................... 1 ............S/N3656071~
ACOUSTIC SHEET
1
DUCT ................................................... 1 ............S/N3656071~
ACOUSTIC SHEET
1
HEX. NUT ............................................. 10 ..........S/N3656071~
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 91
DCA-60SSI2 --- RUBBER SEAL ASSY.
RUBBER SEAL ASSY.
PAGE 92 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- RUBBER SEAL ASSY.
RUBBER SEAL ASSY. UP TO S/N3656070
NO.
PART NO.
ITEM
57
58
59
60
61
62
63
64
65
66
67
68
7455104104
7455104204
7455104304
7455104404
7455104514
7455104614
7455104714
7455104804
7455104904
0225100365
0220100365
0220200750
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL ASSY. S/N3656071~
NO.
PART NO.
ITEM
57
58
59
60
61
62
63
64
65
66
67
68
74
75
76
0229200668
0228900665
0228900890
0228900890
0228900555
0228800335
0228900555
0228901465
0229200900
0228800365
0228800325
0228800780
0278100120
0228100560
0228900670
QTY.
REMARKS
2
2
3
1
1
1
1
2
2
1
1
2
QTY.
REMARKS
RUBBER SEAL
2
RUBBER SEAL
1
RUBBER SEAL
3
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
2
RUBBER SEAL
1
RUBBER SEAL
1
RUBBER SEAL
2
RUBBER SEAL .................................... 2 ............SN3700638~
RUBBER SEAL .................................... 1 ............S/N3700638~
RUBBER SEAL .................................... 2 ............S/N3700638~
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 93
DCA-60SSI2 --- DECALS
DECAL ASSY.
PAGE 94 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
DCA-60SSI2 --- DECALS
DECAL ASSY.
NO.
PART NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
50
B9521100504
B4551005902
0800520904
0800520804
B9521100404
B9531100604
3340670002
8050670113
B1551001604
0840614104
0840619904
0840627103
8080670514
B9531100604
B9511100404
B9531100504
B9511100304
0800689404
0800689504
1320620904
1320610603
6360610304
6360620004
6360620204
0840627304
1320621504
0840625902
B9504200004
B9504000404
B9504500004
B9504100104
B9504000304
7450630703
7450631104
B4561100403
7450631304
B4561100503
7450631504
B4561100604
7450630904
B4561100304
7450630303
B4561100003
7450630303
ITEM
QTY.
REMARKS
DECAL; CAUTION ....................................................... 1 ....... B92110050
DECAL; CONTROL PANEL ........................................ 1 ....... B45100590
PLATE; AMMETER CHANGE-OVER SWITCH .......... 1 ....... N2438
PLATE; VOLTAGE CHANGE-OVER SWITCH ........... 1 ....... N2439
DECAL; SAFETY INSTRUCTION .............................. 1 ....... B92110040
DECAL; WARNING ..................................................... 1 ....... B93110060
DECAL; OPERATING PANEL ..................................... 1 ....... S2361A
DECAL; RECEPTABLE & CIRCUIT BREAKER .......... 1 ....... S3349A
DECAL; NOTE ............................................................. 1 ....... B15100160
DECAL; GROUND MARK ........................................... 1 ....... S2635
DECAL; CAUTION ....................................................... 1 ....... S2731
DECAL; CABLE JOINING ........................................... 1 ....... S3245
DECAL; CAUTION ....................................................... 1 ....... S3696B
DECAL; WARNING ELECTRIC SHOCK HAZARD .... 1 ....... B93110060
DECAL; WARNING ELECTRIC SHOCK HAZARD .... 1 ....... B91110040
DECAL; WARNING ELECTRIC SHOCK HAZARD .... 1 ....... B93110050
DECAL; WARNING ..................................................... 1 ....... B91110030
DECAL; + ..................................................................... 1 ....... S2090
DECAL; - ...................................................................... 1 ....... S2091
DECAL; DIESEL FUEL ................................................ 1 ....... S1756
DECAL; WATER, OIL .................................................. 1 ....... S1760
DECAL; WATER .......................................................... 1 ....... S1880
DECAL; FUEL DRAIN PLUG ...................................... 1 ....... S1883
DECAL; OIL DRAIN PLUG .......................................... 1 ....... S1885
DECAL; WARNING ..................................................... 1 ....... S3247
DECAL; SUPPORT HOOK ......................................... 2 ....... S2257
DECAL; MQ ................................................................. 1 ....... S3057
DECAL; WARNING ENGINE EXHAUST .................... 1 ....... B90420000
DECAL; WARNING MOVING PARTS ......................... 2 ....... M90400040
DECAL; WARNING DIESEL FUEL ............................. 1 ....... B90450000
DECAL; WARNING HOT COOLANT ......................... 1 ....... B90410010
DECAL; CAUTION HOT PARTS ................................. 1 ....... B90400030
STRIPE ........................................................................ 1 ....... REPLACES B4561100103
STRIPE ........................................................................ 2 ....... UP TO S/N3656070
STRIPE ........................................................................ 2 ....... S/N3656071~
STRIPE, LEFT SIDE ................................................... 1 ....... UP TO S/N3656070
STRIPE ........................................................................ 1 ....... S/N3656071~
STRIPE, RIGHT SIDE ................................................. 1 ....... UP TO SN3656070
STRIPE ........................................................................ 1 ....... S/N3656071~
STRIPE ........................................................................ 2 ....... UP TO S/N3656070
STRIPE ........................................................................ 2 ....... S/N3656071~
STRIPE ........................................................................ 1 ....... UP TO S/N3656070
STRIPE ........................................................................ 1 ....... S/N3656071~
STRIPE ........................................................................ 1 ....... UP TO S/N3656070
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 95
ISUZU 6BG1 — CYLINDER HEAD COVER ASSY.
CYLINDER HEAD COVER ASSY.
PAGE 96 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — CYLINDER HEAD COVER ASSY.
CYLINDER HEAD COVER ASSY.
NO
PART NO
PART NAME
1
1111803500
CYLINDER HEAD COVER
27
9111790300
GASKET
68
9111791050
CAP NUT WASHER
69
1111730550
GASKET
75
8943401920
NUT
QTY.
1
4
4
1
4
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 97
EA1013
ISUZU 6BG1 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 98 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO
PART NO
1
1111106142
2
1111411960
4*
5117210010
5A*
1117150540
5B*
1117110430
7A*
1096000051
7B*
9111291280
7C*
5112190150
7D*
5096000130
7E*
1096000160
7F
9111296010
9
9041108250
10
1825130430
11A
5197320011
11B
5197320021
12
9117776221
14
9096300260
41A
0286810200
41B
0208014250
54
9098301630
56
1093000180
81*
9096600340
112
9099167550
113
0280806100
117
9091505140
120A 1090701010
120B 1090701000
168
5117770551
PART NAME
QTY.
REMARKS
CYLINDER HEAD ASSY. .................. 1 ........ INCL. ITEMS W/*
GASKET
1
VALVE GUIDE
12
INLET SEAT
6
EXHAUST SEAT
6
SEALING CUP, OD=45
1
SEALING CUP, OD=20
3
SEALING CUP, OD=32
3
SEALING CUP, OD=12.3
6
SEALING CUP, OD=25
5
SEALING CUP, OD=12.5
5
STUD, M8X25 L=37
3
GLOW PLUG ..................................... 6 ........ REPLACES 9825139289
CONNECTOR, L=236
1
CONNECTOR, L=354
1
HANGER
1
STUD, M8X86 L=99
12
BOLT, M10X20 FLANGE
3
BOLT, M14X25
1
STUD, M8X83 L=96
4
STUD, M8X40 L=58
12
PLUG, OD=11.9
6
CLIP
1
BOLT, M6X10 FLANGE
1
WASHER
1
BOLT, M12X113
20
BOLT, M12X100
6
HANGER
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 99
ISUZU 6BG1 — CYLINDER BLOCK ASSY.
CYLINDER BLOCK ASSY.
PAGE 100 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — CYLINDER BLOCK ASSY.
CYLINDER BLOCK ASSY.
NO.
PART NO.
PART NAME
1
2
1112103408
1878116900
1878119420
1878116910
1878119430
1878116920
1878119440
1878116930
1878119450
1112612480
1112613820
1112612490
1112613830
1112612500
1112613840
1112612510
1112613850
1112612520
1112613860
1112612530
1112613870
1112612540
1112613880
1112612550
1112613890
1090004691
1096660360
1112191630
8941480790
8970233390
5096230350
1096050681
1097400780
1096050660
1096000520
8943673681
8970285250
9112916051
8943675301
1096000121
5093000231
9081510180
CYLINDER BLOCK
1 .......... INCL. ITEMS W/*
LINER, GRADE=1 ................................................. 6 .......... UP TO DEC. 98; INCL. ITEMS W/#
LINER, GRADE=1 ................................................. 6 .......... FROM JAN. 99~
LINER, GRADE=2 ................................................. 6 .......... UP TO DEC. 98
LINER, GRADE=2 ................................................. 6 .......... FROM JAN. 99~
LINER, GRADE=3 ................................................. 6 .......... UP TO DEC. 98
LINER, GRADE=3 ................................................. 6 .......... FROM JAN. 99~
LINER, GRADE=4 ................................................. 6 .......... UP TO DEC. 98
LINER, GRADE=4 ................................................. 6 .......... FROM JAN. 99~
LINER, OD GRD=1 ID GRD=AX ........................... 6 .......... UP TO DEC. 98
LINER, OD GRD=1 ID GRD=AX ........................... 6 .......... FROM JAN. 99~
LINER, OD GRD=1 ID GRD=CX ........................... 6 .......... UP TO DEC. 98
LINER, OD GRD=1 ID GRD=CX ........................... 6 .......... FROM JAN. 99~
LINER, OD GRD=2 ID GRD=AX ........................... 6 .......... UP TO DEC. 98
LINER, OD GRD=2 ID GRD=AX ........................... 6 .......... FROM JAN. 99~
LINER, OD GRD=2 ID GRD=CX ........................... 6 .......... UP TO DEC. 98
LINER, OD GRD=2 ID GRD=CX ........................... 6 .......... FROM JAN. 99~
LINER, OD GRD=3 ID GRD=AX ........................... 6 .......... UP TO DEC. 98
LINER, OD GRD=3 ID GRD=AX ........................... 6 .......... FROM JAN. 99~
LINER, OD GRD=3 ID GRD=CX ........................... 6 .......... UP TO DEC. 98
LINER, OD GRD=3 ID GRD=CX ........................... 6 .......... FROM JAN. 99~
LINER, OD GRD=4 ID GRD=AX ........................... 6 .......... UP TO DEC. 98
LINER, OD GRD=4 ID GRD=AX ........................... 6 .......... FROM JAN. 99~
LINER, OD GRD=4 ID GRD=CX ........................... 6 .......... UP TO DEC. 98
LINER, OD GRD=4 ID GRD=CX ........................... 6 .......... FROM JAN. 99~
BOLT, M16X119
14
CONNECTOR
1
COVER
1
PIN, OD=16
2
VALVE
1
GASKET
1
PLUG
2
PIN, OD=10 L=50
1
PLUG, PT 3/8 T=8.0
1
SEALING CUP, OD=60
2
GASKET
3
COVER
2
COVER
1
BOLT, M8X56 FLANGE
6
CUP, OD=32
3
STUD, M14X44 L=65
1
PIN, OD=10 L=18
2
4*#
8*
12
28
30
34
35
37
38
55
70*
71
72C
72D
74
80*
82
83
QTY.
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 101
ISUZU 6BG1 — CYLINDER BLOCK ASSY.
CYLINDER BLOCK ASSY.
PAGE 102 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — CYLINDER BLOCK ASSY.
CYLINDER BLOCK ASSY.
NO.
PART NO.
PART NAME
113*
130*
136
137
162
179
218
219
220
236
242
267
269
279
281
335A
335B
335C
335D
338
5112190140
5112570011
9112246021
1096800240
9099147010
9095720080
9095714120
9095720140
5096540130
9098600190
1093000530
0286808200
8970157540
1096301150
0286810200
5197890030
5096050180
1096050791
9992023140
9992023120
5111290030
QTY.
REMARKS
CUP, OD=28
2
DOWEL
1
BUSHING
1
DRAIN COCK
1
HOSE, L=900 S.B. L=10000
1
GASKET
6
GASKET ................................................................ 1 .......... UP TO MAR. 98
GASKET ................................................................ 1 .......... FROM APR. 98~
NIPPLE
1
PLUG
1
STUD, M10X18.5 L=33
1
BOLT, M8X20 FLANGE
2
CLIP
1
GASKET
1
BOLT, M10X20 FLANGE
2
BRACKET
1
PLUG, RIGHT SIDE
8
PLUG, LEFT SIDE
1
PLUG, LEFT SIDE
1
PLUG, RIGHT SIDE
1
SEALING CUP, OD=15.6
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 103
ISUZU 6BG1 — OIL PAN AND LEVEL GAUGE ASSY.
OIL PAN AND LEVEL GAUGE ASSY.
PAGE 104 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — OIL PAN AND LEVEL GAUGE ASSY.
OIL PAN AND LEVEL GAUGE ASSY.
NO.
1
2
5*
6*
16
23
119C
120
151
153
PART NO.
1113604421
1117602000
1096230570
9096620120
1113671000
0500408180
9992023240
9992023160
9095714240
9095714160
9112290700
9831514320
PART NAME
QTY.
REMARKS
OIL PAN ASSY. ............................................... 1 .......... INCL. ITEMS W/*
GAUGE
1
GASKET
1
PLUG
1
GASKET
1
BOLT, M8X12 W/LOCK WASHER
32
PLUG, M24X12
1
PLUG; M16X12
1
GASKET, ID=24.5
1
GASKET, ID=16.5
1
CLIP
1
THERMOMETER
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 105
ISUZU 6BG1 — CAMSHAFT AND VALVE ASSY.
CAMSHAFT AND VALVE ASSY.
PAGE 106 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — CAMSHAFT AND VALVE ASSY.
CAMSHAFT AND VALVE ASSY.
NO.
1
4
5
7
8
9
10
11
14
37A
37B
51
53
55
58
65
68
71A
71B
72
75A
75B
76
78
81
83
84
88
89
93
94
95
100
103
107
111
112
207
PART NO.
1125140050
1125510830
1125520251
9920614280
9098518503
1125220162
9116810150
0500408250
9080307130
9116110480
9116130350
9091800190
1126210621
9126260050
5126280120
5126560060
1125610990
8941145790
5125630010
1125690150
1090005670
9096021480
9098514300
1126111180
9126160420
9091115080
9126281050
1125750360
5125710032
1094001160
9095814300
1095803350
5096230600
9091505100
9125310300
5125350011
8941339373
0108110550
PART NAME
CAMSHAFT
VALVE, INLET
VALVE, EXHAUST
BOLT, M14X28
WASHER, ID=14.5
GEAR, Z=50
THRUST PLATE
BOLT, M8X25 W/LOCK WASHER
KEY
METAL
METAL
SNAP RING
ROCKER ARM SHAFT
PLUG
BRACKET
SPLIT COLLAR
VALVE SPRING
SPRING SEAT
SPRING SEAT
SEAL
BOLT, M8X65
BOLT, M8X65
WASHER
ROCKER ARM
SCREW
ADJ. SCREW LOCK NUT
BRACKET
PUSH ROD
TAPPET VALVE
NUT
WASHER
SPRING
GASKET
WASHER
SHAFT
COLLAR
GEAR
BOLT, M10X55
QTY.
1
6
6
1
1
1
1
2
1
1
5
1
1
2
1
24
12
12
12
12
8
1
9
12
12
12
6
12
12
4
4
5
1
2
1
1
1
2
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 107
ISUZU 6BG1 — CRANKSHAFT, PISTON AND FLYWHEEL ASSY.
CRANKSHAFT, PISTON AND FLYWHEEL ASSY.
PAGE 108 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — CRANKSHAFT, PISTON AND FLYWHEEL ASSY.
CRANKSHAFT, PISTON AND FLYWHEEL ASSY.
NO
1
7
12
13
14
15
28
31
32*
33
35
37
38
40
42#
56
63
68
73
83
84
85%
86%
93
96
126
PART NO
1123104480
1115100742
5123310642
9098401071
9098514310
9123790450
8971379101
5097380010
9081512200
5123190032
9123336070
1098002140
5123360081
9098013340
1116800012
5123712092
1121117690
1121117700
1121211011
9122716080
9122116040
1122301041
1122510270
1122350271
1123620031
5123620031
8941075751
PART NAME
QTY.
REMARKS
CRANKSHAFT ............................ 1 ........ INCL. ITEMS W/*
METAL KIT ................................. 1 ........ INCL. ITEMS W/#
FLYWHEEL
1
NUT
1
WASHER
1
BUSHING
1
GEAR, Z=25
1
FEATHER KEY
1
PIN
1
RING
1
GEAR, Z=129
1
BEARING
1
WASHER
1
BOLT
6
WASHER
2
PULLEY, 2-GROOVE
1
PISTON, STD. GRD=AX
6
PISTON, STD. GRD=CX
6
RING SET
6
METAL SET
6
PISTON PIN
6
CONNECTOR ARM ASSY. ......... 6 ........ INCL. ITEMS W/%
BUSHING
6
BOLT, M20X49.5
12
THROWER
1
DUST THROWER
1
SNAP RING
12
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 109
ISUZU 6BG1 — TIMING GEAR AND FLYWHEEL HOUSING ASSY.
TIMING GEAR AND FLYWHEEL HOUSING ASSY.
PAGE 110 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — TIMING GEAR AND FLYWHEEL HOUSING ASSY.
TIMING GEAR AND FLYWHEEL HOUSING ASSY.
NO.
1
2
32
35
36
38
49
54
57
58
62A
62B
65
86
93
175
178
205
211
224
252
275
297
298
PART NO.
5113110113
8943213304
8943706710
1096254380
0280808450
0286808200
9081510180
8970222160
1113210790
5113210090
0280806120
0286808250
0280808500
8970276011
9839101012
1096234650
1096254391
8943218380
0911602140
0500408250
9944112350
0286808200
5113270090
9095714160
9992023160
PART NAME
QTY.
REMARKS
TIMING GEAR CASE
1
FLYWHEEL HOUSING
1
GASKET
1
SEAL
1
BOLT, M8X45 FLANGE
2
BOLT, M8X20 FLANGE
4
PIN, OD=10 L=18
1
GASKET
1
COVER
1
TIMING COVER
2
BOLT, M6X12 FLANGE
4
BOLT, M8X25 FLANGE
7
BOLT, M8X50 FLANGE
5
GASKET
2
ELBOW
1
GASKET
1
SEAL
1
PLUG
1
NUT
1
BOLT, M8X25 W/LOCK WASHER .. 7 ........... REPLACES 0288914450
STUD, M12X35 L=53
3
BOLT, M8X20 FLANGE
2
POINTER
1
GASKET
1
PLUG
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 111
ISUZU 6BG1 — INLET MANIFOLD ASSY.
INLET MANIFOLD ASSY.
PAGE 112 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — INLET MANIFOLD ASSY.
INLET MANIFOLD ASSY.
NO.
1
7
10A
10B
13
20A
20B
22
23
27
27A
32
50G
50I
54
55
94
159
168
225A
225B
231
PART NO.
1141121842
1141150610
1141150590
1096370610
0501408280
9091104080
0911501080
9091505080
9091605080
9040108200
9040108450
9044110250
1141123150
1141126310
9091505100
9091104100
0500406300
8941640270
1154192151
9044110280
5093000290
1154192162
PART NAME
QTY.
REMARKS
INLET MANIFOLD
1
GASKET
1
GASKET
1
GASKET
1
BOLT, M8X28 ................................. 9 ........... W/LOCK AND PLAIN WASHER
NUT. M8
3
NUT, M8 FLANGE
3
LOCK WASHER
3
PLAIN WASHER
3
STUD, M8X20 L=36
3
STUD, M8X45 L=61
3
STUD, M10X25 L=40
2
PIPE
1
PIPE
1
LOCK WASHER
2
NUT
2
BOLT, M6X30 ................................. 1 ........... W/LOCK WASHER
PIPE
1
CLIP
1
STUD, M10X28 L=43
2
STUD, M10X18 L=33
2
STAY
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 113
ISUZU 6BG1 — EXHAUST MANIFOLD ASSY.
EXHAUST MANIFOLD ASSY.
PAGE 114 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — EXHAUST MANIFOLD ASSY.
EXHAUST MANIFOLD ASSY.
NO.
1A
1B
2C
2A
16
18
155
PART NO.
9141412761
9141418030
1141451140
8944046100
9044110300
9098445650
9141496530
PART NAME
QTY.
REMARKS
EXHAUST MANIFOLD
1
EXHAUST MANIFOLD
1
GASKET ............................................. 6 ............. UP TO MAR. 99
GASKET ............................................. 3 ............. FROM APR. 99~
STUD, M10X30 L=45
3
NUT
12
RING
3
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 115
ISUZU 6BG1 — VENTILATION ASSY.
VENTILATION ASSY.
PAGE 116 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — VENTILATION ASSY.
VENTILATION ASSY.
NO.
23
24
141
142
143
PART NO.
1093607520
1097070841
8941101110
1143620020
9934905100
PART NAME
HOSE, L=240
CLIP, ID=20
DIAPHRAGM ASSY.
COVER
SCREW, M5X10 PANHEAD
QTY.
1
2
1
1
6
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 117
ISUZU 6BG1 — WATER PUMP AND CORROSION RESISTOR ASSY.
WATER PUMP AND CORROSION RESISTOR ASSY.
PAGE 118 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — WATER PUMP AND CORROSION RESISTOR ASSY.
WATER PUMP AND CORROSION RESISTOR ASSY.
NO.
1
3
4*
7
8*#
9A*#
9B*
10A*
10B*
11*
17*#
18*#
19*#
20*
24*
25*
28*#
29*#
65*
66*#
117*
PART NO.
1136500180
8943706610
1878112530
5136410381
1136411870
5136390010
9099521430
9091801520
5098000510
5098000500
5136340020
5136200062
9136218020
9136136130
9136128020
0280810700
0280810500
0286810350
5136420072
1095030700
1136310740
9030908200
5096250550
1096601192
PART NAME
QTY.
REMARKS
PUMP ASSY ........................ 1 ..................... INCL. ITEMS W/*
GASKET
1
REPAIR KIT .......................... 1 ..................... INCL. ITEMS W/#
PULLEY, 2-GROOVE, D=173 1 ..................... UP TO MAR. 99
PULLEY, 2-GROOVE, D=173 1 ..................... FROM APR. 99~
THROWER
1
SNAP RING
1
SNAP RING
1
BEARING
1
BEARING
1
SPACER
1
SEAL UNIT
1
IMPELLER
1
GASKET
1
COVER
1
BOLT, M10X70 FLANGE
1
BOLT, M10X50
2
BOLT, M10X35
1
CENTER
1
WASHER
1
SHAFT
1
SCREW
3
SEAL
1
CONNECTOR
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 119
ISUZU 6BG1 — THERMOSTAT AND HOUSING ASSY.
THERMOSTAT AND HOUSING ASSY.
PAGE 120 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — THERMOSTAT AND HOUSING ASSY.
THERMOSTAT AND HOUSING ASSY.
NO.
1
2
14
17
28
44A
44B
47
48
49
50
64
65
107
PART NO.
1137700700
5137160260
9096640050
5097040460
9096620340
0286810350
0108060950
9091505100
9091605100
1137130370
0501408250
1137430160
113740130
5137210152
PART NAME
QTY.
REMARKS
THERMOSTAT
1
HOUSING
1
PLUG, PT 3/4
1
CLIP
2
HEATER PLUG, M25
1
BOLT, M10X35
3
BOLT, M10X95
3
LOCK WASHER
3
PLAIN WASHER
3
PIPE
1
BOLT, M8X25 ............................ 3 ................ W/LOCK AND PLAIN WASHER
GASKET
1
GASKET
1
PIPE
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 121
ISUZU 6BG1 — ENGINE WATER PIPING ASSY.
ENGINE WATER PIPING ASSY.
PAGE 122 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — ENGINE WATER PIPING ASSY.
ENGINE WATER PIPING ASSY.
NO.
132
PART NO.
8971380860
PART NAME
HOSE
QTY.
1
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 123
ISUZU 6BG1 — FAN AND FAN BELT ASSY.
FAN AND FAN BELT ASSY.
PAGE 124 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — FAN AND FAN BELT ASSY.
FAN AND FAN BELT ASSY.
NO.
1
16
24
36
38A
38G
68
69
70
71
80
81
86
110
122
PART NO.
8944838971
9091647080
1090440730
1136712260
8944340750
1136420470
9091505120
9091607120
9991104120
1090091141
1136741181
1136741610
0286810250
9034906100
9091505080
PART NAME
FAN, D=550-7 BLOW
PLAIN WASHER
BOLT
BELT, L=1246 2 PIECE SET
SPACER, T=51.7
SPACER, T=61
LOCK WASHER
PLAIN WASHER
NUT
BOLT, M10X155
ADJ. PLATE
SLIDING PIECE
ADJ. BOLT, M10X25 FLANGE
SCREW, M6X10
LOCK WASHER
QTY.
1
4
4
1
1
1
1
2
1
1
1
1
1
2
4
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 125
ISUZU 6BG1 — FUEL INJECTION ASSY.
FUEL INJECTION ASSY.
PAGE 126 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — FUEL INJECTION ASSY.
FUEL INJECTION ASSY.
NO.
1
2
3
4A
4B
7C
7D
15*
16
17
18
19
20
21
31
32
33
34#
35#
36#
37#
38#
39#
41#
42#
44#
45#
46#
54
60
62
66
75
78
80
85
114
133
134
135
PART NO.
1156032880
0108108750
9091505080
9098519340
9091605080
0108108600
0500410250
1157801720
1154151831
1154151841
1154151851
1154151861
1154151871
1154151881
1153002912
8970161471
5153110270
1096750371
1153320170
1096300820
5153320060
5153390600
8941695030
8943203080
5153390030
5153430050
8941695020
9153470030
9153390510
9091505080
9091104080
5153150030
9091607100
0500410200
1197511200
8943706750
9154196120
1154124711
1096750371
1096300820
PART NAME
QTY.
REMARKS
FUEL INJ. PUMP ASSY. ........... 1 ................ INCL. ITEMS W/*
BOLT, M8X75
4
LOCK WASHER
7
WASHER
4
WASHER
7
BOLT, M8X60 ............................ 7 ................ REPLACES 0108058600
BOLT, M10X25 ........................... 1 ................ W/LOCK WASHER
COUPLING ASSY.
1
PIPE, INJ. NO. 1
1
PIPE, INJ. NO. 2
1
PIPE, INJ. NO. 3
1
PIPE, INJ. NO. 4
1
PIPE, INJ. NO. 5
1
PIPE, INJ. NO. 6
1
NOZZLE ASSY.
6
HOLDER ASSY. ........................ 6 ................ INCL. ITEMS W/#
NOZZLE
6
BOLT
6
NUT
6
GASKET, ID=8 OD=13.2
12
NUT
6
GASKET
6
SCREW
6
CONNECTOR
6
GASKET
6
SPRING
6
PUSH ROD
6
PIN
12
COVER
6
LOCK WASHER
12
NUT
12
GASKET
6
PLAIN WASHER
3
BOLT, M10X20 ........................... 2 ................ W/PLAIN WASHER
BRACKET
1
GASKET
1
CLIP
6
PIPE
1
BOLT
1
GASKET, ID=8.2 OD=13.2
2
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 127
ISUZU 6BG1 — FUEL FILTER AND BRACKET ASSY.
FUEL FILTER AND BRACKET ASSY.
PAGE 128 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — FUEL FILTER AND BRACKET ASSY.
FUEL FILTER AND BRACKET ASSY.
NO.
1
21*
29*
30*
58*
62
63
64
72
99
PART NO.
1132007011
1132121080
1132600470
1096300850
1132400691
9091104100
9091505100
9091605100
9091105100
9091505100
PART NAME
QTY.
REMARKS
FUEL FILTER ASSY. ................. 1 ................ INiICL. ITEMS W/*
COVER
1
VALVE
1
GASKET
2
ELEMENT
1
NUT
2
LOCK WASHER
2
PLAIN WASHER
2
NUT, M10
2
LOCK WASHER
2
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 129
ISUZU 6BG1 — FUEL PUMP AND PIPE ASSY.
FUEL PUMP AND PIPE ASSY.
PAGE 130 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — FUEL PUMP AND PIPE ASSY.
FUEL PUMP AND PIPE ASSY.
NO.
107
108
110
111A
111C
112
115
119
123
124
126
145
150
212
216
217
PART NO.
1154142940
1096750860
1096300850
5097091030
5097091040
1096750860
1096300850
1154142950
1154142962
1094680021
0500406300
9095245550
1096300850
1132600011
0500406300
1096300850
PART NAME
QTY.
REMARKS
PIPE
1
BOLT
1
GASKET
2
CLIP, W/TUBE L=48
3
CLIP, W/OUT TUBE L=45
3
BOLTM14X27
1
GASKET, ID=14.2 OD=19.2
2
PIPE
1
PIPE
1
NUT
1
BOLT M6X30 ............................. 2 ................ W/LOCK WASHER
CLIP, ID=6
1
GASKET, ID=14.2 OD=19.2
2
OVERFLOW VALVE
1
BOLT, M6X30 ............................ 1 ................ W/ LOCK WASHER
GASKET, ID=14.2 OD=19.2
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 131
ISUZU 6BG1 — OIL COOLER AND OIL FILTER ASSY.
OIL COOLER AND OIL FILTER ASSY.
PAGE 132 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — OIL COOLER AND OIL FILTER ASSY.
OIL COOLER AND OIL FILTER ASSY.
NO.
2
76A
76B
102
103A
103B
103C
103D
107
110*
111*
115*
116*
189*
190*
191*
192*
196
265#
281#
284#
288#
290A%#
290B%#
290C%#
292
293
297
307
309
321
328
331
333
410
444*
469
496
PART NO.
1878100752
9098009281
0286810350
1217002491
8942059861
0501408450
0501408280
1090300910
9091605080
1112810281
1112820180
9091114100
9091645100
9132630100
9095622150
5095800920
5112880010
5096050170
5132110100
5132120212
1132310420
109000105
9099203110
9099206940
1096230550
9099412830
9132390250
9098621610
5132600061
1096231630
8943706700
8941486171
9091605100
9095720100
1096231630
1112820140
112820200
5132000726
PART NAME
QTY.
REMARKS
OIL FILTER ELEMENT ............. 1 ................ INCL. ITEMS W/%
BOLTM10X145
2
BOLT, M10X35
2
OIL COOLER ASSY. ................. 1 ................ INCL. ITEMS W/*
BOLT, M8X65
1
BOLT, M8X65 .......................... 10 ................ W/LOCK AND PLAIN WASHER
BOLT. M8X28 ........................... 15 ................ W/LOCK AND PLAIN WASHER
BOLT, M8X20 ............................ 2 ................ W/PLAIN WASHER
PLAIN WASHER
3
BODY
1
CORE
1
NUT
4
PLAIN WASHER
4
PLUG
1
GASKET
1
BYPASS SPRING
1
BYPASS VALVE
1
PLUG
2
BODY
1
COVER
1
BOLT
1
PLUG, M10
1
GASKET
1
GASKET, ID=15.5
1
GASKET, ID=9.8
1
SPRING
1
SEAT
1
PLUG
1
VALVE
1
GASKET
1
GASKET
1
BOLT
1
PLAIN WASHER
2
GASKET, ID=10.2 OD=19
2
GASKET
1
GASKET
2
GASKET
1
OIL FILTER ASSY. .................... 1 ................ INCL. ITEMS W/#
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 133
ISUZU 6BG1 — OIL PUMP AND OIL STRAINER ASSY.
OIL PUMP AND OIL STRAINER ASSY.
PAGE 134 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — OIL PUMP AND OIL STRAINER ASSY.
OIL PUMP AND OIL STRAINER ASSY.
NO.
1
2*
3*
5*
8*
11*
20*
29
32*
37*
39*
40*
41*
42*
65
97*
PART NO.
1131002770
5131650040
9081140300
5095800980
5131250010
1131130470
5131210050
0286810250
1131280180
1131190030
9131190100
1131230160
5098430030
1131401160
9131190100
1090440470
PART NAME
QTY.
REMARKS
OIL PUMP ASSY. ...................... 1 ................. INCL. ITEMS W/*
SEAT
1
PIN
1
SPRING
1
GEAR
1
COVER ASSY.
1
GEAR
1
BOLT, M10X25 FLANGE
2
PINION
1
DOWEL
1
COLLAR
1
COUPLING
1
BALL
1
STRAINER
1
COLLAR
1
BOLT, M8X60
4
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 135
ISUZU 6BG1 — OIL AND VACUUM PIPING ASSY.
OIL AND VACUUM PIPING ASSY.
PAGE 136 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — OIL AND VACUUM PIPING ASSY.
OIL AND VACUUM PIPING ASSY.
NO.
1
2
37
40
47A
47B
62
110
117
134*
143
277#
278
279
430
434
448
PART NO.
5133112050
1096750770
5133111190
0286808400
9099211880
1096234620
1133115322
9098440220
1096300830
9099171051
0280808400
1117500241
9099129760
9099155531
9091505080
9091104080
1117402011
PART NAME
QTY.
REMARKS
PIPE ....................................... 1 ................... INCL. ITEMS W/*
BOLT, M10X21
1
PIPE
1
BOLT, M8X40 FLANGE
4
GASKET, ID=18
2
GASKET, ID=22.8
2
PIPE
1
NUT
1
GASKET, ID=10.2
2
CLIP
1
BOLT, M8X40 FLANGE
4
CAP
1
HOSE
1
CLIP
2
LOCK WASHER
1
NUT
1
FILLER ................................... 1 ................... INCL. ITEMS W/#
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 137
ISUZU 6BG1 — ELECTRICAL CONTROL ASSY.
ELECTRICAL CONTROL ASSY.
PAGE 138 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — ELECTRICAL CONTROL ASSY.
ELECTRICAL CONTROL ASSY.
NO.
1
2
7
16
17
18
23
26A
26C
38
56A
56D*
88*
89
252
292
293
488
PART NO.
1811001911
1812003650
9991104120
1090001331
9091605140
9091505140
9991104140
0280810250
0286810350
9825300430
5831510030
9827200690
9099022380
8971256010
1197190362
9091505120
9829322110
1819001931
PART NAME
QTY.
REMARKS
STARTER ASSY.
1
GENERATOR ASSY.
1
NUT
3
BOLT, M14X135
1
PLAIN WASHER
1
LOCK WASHER
1
NUT
1
BOLT, M10X25 FLANGE
1
BOLT, M10X35
2
RESISTOR
1
SWITCH ................................... 1 .................. INCL. ITEMS W/*
SWITCH
1
ADAPTER
1
SWITCH
1
COVER
1
LOCK WASHER
3
CABLE
1
STOPPER
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 139
ISUZU 6BG1 — STARTER COMP. ASSY.
STARTER COMP. ASSY.
PAGE 140 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — STARTER COMP. ASSY.
STARTER COMP. ASSY.
NO.
PART NO.
PART NAME
1
2
3%
4
5
6
8
9&
10
11A
11B
11C
12
15
16
17A#
1811293640
1811230250
1811293970
5811291420
5811291440
5811291450
1811130260
1811293860
1811230240
5811291600
5811291590
5811291580
1811130730
1811160440
1811210370
1811293950
5811291550
1811293850
1811291960
5811291560
1811293960
1811160420
1811170140
1811180360
1811150620
1811293870
5811292140
1811270310
1811291850
5811291470
5811510360
1811160430
5811220160
1811150610
5811291500
5811291460
5811291480
9821161400
5811180190
9821161420
5811291510
5811291490
1812291140
1811293840
1811291840
1825530230
1825530370
SEAL KIT ........................................ 1 .................. INCL. ITEMS W/1
CASE .............................................. 1 .................. INCL. ITEMS W/%
METAL
1
COVER
1
CLIP
2
STOPPER
1
BRACKET
1
BEARING
1
SHAFT ........................................... 1 .................. INCL. ITEMS W/&
WASHER
1
WASHER
2
WASHER
1
BRACKET
1
WIRE
1
ARMATURE ................................... 1 .................. INCL. ITEMS W/#
BEARING ....................................... 1 .................. UP TO MAR. 95
BEARING ....................................... 1 .................. FROM APR. 95~
BEARING ....................................... 1 .................. UP TO MAR. 95
BEARING ....................................... 1 .................. FROM APR. 95~
WASHER
2
COIL
1
BRUSH, +
2
SPRING
2
HOLDER
1
COVER
1
BOLT
3
BOLT
2
LEVER
1
PIN
1
PLATE
1
SWITCH
1
BRUSH, 2
CLUTCH
1
COVER ASSY. ................................ 1 .................. INCL. ITEMS W/*
TERMINAL
1
PLUNGER
1
CONTACT
1
BUSHING
1
HOLDER
1
WASHER
1
WASHER
2
RING
2
WASHER
2
TERMINAL
1
NUT
1
RELAY ............................................ 1 .................. UP TO MAR. 95
RELAY ............................................ 1 .................. FROM APR. 95~
17B#
18
19
20*
21*
22*
23*
27A
27B
28
29
30
31
50*
54
57
59
60
61
62
63
64A
64B
65
77
78
80
86
QTY.
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 141
ISUZU 6BG1 — ALTERNATOR COMP. ASSY.
ALTERNATOR COMP. ASSY.
PAGE 142 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — ALTERNATOR COMP. ASSY.
ALTERNATOR COMP. ASSY.
NO.
PART NO.
PART NAME
1
2
3T
3U
5
6#
10#
11#
12
13
14B
14C
15H
15F
15I
15L
17
19
20
22
33#
49#
57
62
69
1812142290
1812210720
1812292250
8941730540
1812170620
1812700070
1812170690
1812142240
9822158670
1812293830
1812295270
1812295430
1812295130
1812293760
1812295260
8941730600
1812130670
1812220550
1812230090
1812110900
1812295560
8941730610
1812295440
1812291220
1812295160
REAR COVER
ROTOR
BEARING
BEARING
HOLDER
REGULATOR ASSY.
RECTIFIER
COVER
KEY
GASKET
COLLAR
COLLAR
RETAINER
RETAINER
RETAINER
RETAINER
FRONT COVER
PULLEY
FAN
STATOR
WIRE
BUSHING
COVER
CLIP
CLIP
QTY.
REMARKS
1 .................. INCL. ITEMS W/#
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 143
ISUZU 6BG1 — INJ. PUMP COMP. ASSY.
INJ. PUMP COMP. ASSY.
PAGE 144 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — INJ. PUMP COMP. ASSY.
INJ. PUMP
COMP. ASSY.
NO.
PART NO.
PART NAME
1
6*
7*
8*
9*
10*
14*
19*
33
46
48
49
50*
51
62
63
64
68
69#
70#
71#
72#
73*%
74
75*
77
79*
80
82
88
89
105
5156110250
5156440170
1096230520
5156290450
5156430010
1156490010
5156410010
1156310690
1096230130
1156192430
5156191560
9812250470
5156210250
5196190490
9812350150
5156430090
9812350210
9812212230
5156190410
9812222200
1156290010
1156220030
1157299600
1156120500
1156190030
1156190330
9812151150
8941711100
5156191360
1156190920
1157190930
9000906770
5098000380
5156290150
5156290160
5156290170
5156290180
5156290190
5156290200
5156290380
9812250330
5156190390
5156290900
1156390880
5156370030
5098000380
9000906770
1096300850
1157590110
9812350170
5156190440
9019006140
9812151440
1156190240
HOUSING ............................................ 1 .................... INCL. ITEMS W/*
HOLDER
6
GASKET
6
STOPPER
6
SPRING
6
GASKET
6
VALVE
6
PLUNGER ASSY.
6
GASKET
1
COVER
1
GASKET
14
RING
1
CAMSHAFT
1
KEY
1
SEAT
6
SPRING
6
SET
6
TAPPET ............................................... 6 .................... INCL. ITEMS W/#
GUIDE
6
PIN
6
BUSHING
6
ROLLER
6
GASKET
1
COVER ................................................ 1 .................... INCL. ITEMS W/%
SCREW
2
BEARING
1
STUD
3
NUT
3
PLUG
6
BOLT
1
GASKET
2
BEARING, NSK
1
BEARING, NTN
1
SHIM ................................................. AR .................... T=0.10
SHIM ................................................. AR .................... T=0.12
SHIM ................................................. AR .................... T=0.14
SHIM ................................................. AR .................... T=0.16
SHIM ................................................. AR .................... T=0.18
SHIM ................................................. AR .................... T=0.50
SHIM ................................................. AR .................... T=1.00
SHIM ................................................. AR .................... T=0.30
SHIM ................................................. AR .................... T=0.70
SHIM ................................................. AR .................... T=1.40
SHIM ................................................. AR .................... T=2.40
RACK
1
BEARING, NTN
1
BEARING, NSK
1
GASKET, ID=14.2 OD=19.2
2
BOLT
1
ADAPTER
1
ADAPTER
1
SCREW, M6X14 ................................... 4 .................... W/LOCK WASHER
GASKET
2
BOLT
1
107
109*
114
117
118
126*
127*
130
148*
115
QTY.
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 145
ISUZU 6BG1 — INJ. PUMP COMP. ASSY.
INJ. PUMP COMP. ASSY.
PAGE 146 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — INJ. PUMP COMP. ASSY.
NJ. PUMP COMP. ASSY.
NO.
PART NO.
PART NAME
157*
159
160
161
162
8941445880
9812250470
9884100660
9812250430
5156290150
5156290160
5156290170
5156290180
5156290190
5156290200
5156290380
9812250330
5156190390
5156290900
1156390880
1156390030
5156250010
9812250570
9812350030
5156190340
5156190350
5156190360
5156190010
5156190020
5156190030
5156190040
5156190050
5156190070
5156190080
5156190090
5156190100
5156190110
5156190120
5156190130
5156190150
9812350420
9812350430
9812350440
9812350450
5156191060
5156191070
5156190250
5156190260
5156190270
5156190370
5156191080
5156191090
5156191100
GASKET
1
RING
1
SCREW
2
GASKET
2
SHIM ................................................. AR .................... T=0.10
SHIM ................................................. AR .................... T=0.12
SHIM ................................................. AR .................... T=0.14
SHIM ................................................. AR .................... T=0.16
SHIM ................................................. AR .................... T=0.18
SHIM ................................................. AR .................... T=0.50
SHIM ................................................. AR .................... T=1.00
SHIM ................................................. AR .................... T=0.30
SHIM ................................................. AR .................... T=0.70
SHIM ................................................. AR .................... T=1.40
SHIM ................................................. AR .................... T=2.40
BOLT
1
PLATE
3
PINION
6
SCREW
6
SHIM ................................................. AR .................... T=0.30
SHIM ................................................. AR .................... T=0.40
SHIM ................................................. AR .................... T=0.50
SHIM ................................................. AR .................... T=0.60
SHIM ................................................. AR .................... T=0.70
SHIM ................................................. AR .................... T=0.80
SHIM ................................................. AR .................... T=0.90
SHIM ................................................. AR .................... T=1.00
SHIM ................................................. AR .................... T=1.10
SHIM ................................................. AR .................... T=1.20
SHIM ................................................. AR .................... T=1.30
SHIM ................................................. AR .................... T=1.40
SHIM ................................................. AR .................... T=0.55
SHIM ................................................. AR .................... T=0.65
SHIM ................................................. AR .................... T=0.75
SHIM ................................................. AR .................... T=0.85
SHIM ................................................. AR .................... T=0.95
SHIM ................................................. AR .................... T=1.05
SHIM ................................................. AR .................... T=1.15
SHIM ................................................. AR .................... T=1.25
SHIM ................................................. AR .................... T=1.50
SHIM ................................................. AR .................... T=1.60
SHIM ................................................. AR .................... T=0.20
SHIM ................................................. AR .................... T=0.25
SHIM ................................................. AR .................... T=0.35
SHIM ................................................. AR .................... T=0.45
SHIM ................................................. AR .................... T=1.35
SHIM ................................................. AR .................... T=1.45
SHIM ................................................. AR .................... T=1.55
167*
176
177
178
181
QTY.
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 147
ISUZU 6BG1 — GOVERNOR COMP. ASSY.
GOVERNOR COMP. ASSY.
PAGE 148 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — GOVERNOR COMP. ASSY.
GOVERNOR COMP. ASSY.
NO.
1
2*
3*
4*
5*
7*
8H*
8I*
11*
12*
13*
15*
16*
17*
18*
21*
23*
24*
25*
28*
34*
37*
40*
41*
43*
45*
59*
60Q*
60S*
63*
71*
78*
79*
83*
86*#
87*
PART NO.
1157300480
5157210040
5157290270
8913253970
1157290010
5157210220
5157290540
5157290330
1157290020
1157220210
5196190490
5157290340
9813250860
9813250880
9813255510
9813255520
9813255530
5157292860
5157292870
1157298910
1157298920
1157298930
5157190080
5157250330
1157250110
9813222350
9091854040
5157250420
1157232120
8970267520
1157291010
8944707560
9008130230
1157256680
1157210230
1156192820
5157291670
9813919070
5157230880
1157254490
1157292940
1157292950
1157292960
1157292970
1157292980
1157292990
9813919060
9813254290
9019006160
PART NAME
QTY.
REMARKS
GOVERNOR ASSY. ....................1 ...................... INCL. ITEMS W/*
HOUSING
1
BOLT, M6X15
6
PLATE
1
GASKET
1
COVER ........................................1 ...................... INCL. ITEMS W/#
BOLT
2
BOLT
4
GASKET
1
FLYWEIGHT ASSY.
1
KEY, 16MM
1
LOCK WASHER
1
NUT
1
SHIM ............................................AR ................... T=0.20
SHIM ............................................AR ................... T=0.40
SHIM ............................................AR ................... T=0.60
SHIM ............................................AR ................... T=1.00
SHIM ............................................AR ................... T=0.50
SHIM ............................................AR ................... T=1.50
SHIM ............................................AR ................... T=2.00
SHIM ............................................AR ................... T=3.00
SHIM ............................................AR ................... T=4.00
SLEEVE
1
LEVER ASSY.
1
LING
1
SPRING
1
SNAP RING
1
LEVER
1
SPRING
1
LEVER ASSY.
1
SCREW
1
SPRING CAPSULE
1
NUT
1
LEVER ASSY.
1
COVER
1
BOLT
2
BOLT
1
GASKET
1
SPRING
1
LEVER
1
SHIM ............................................AR ................... T=0.20
SHIM ............................................AR ................... T=0.25
SHIM ............................................AR ................... T=0.30
SHIM ............................................AR ................... T=0.35
SHIM ............................................AR ................... T=0.40
SHIM ............................................AR ................... T=0.50
SEAL
1
BUSHING
1
BOLT
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 149
ISUZU 6BG1 — GOVERNOR COMP. ASSY.
GOVERNOR COMP. ASSY.
PAGE 150 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — GOVERNOR COMP. ASSY.
GOVERNOR COMP. ASSY.
NO.
PART NO.
PART NAME
90*
918*
93S*
93T*
93U*
93V*
94*
96*
99*
101*
103*
104*
105*
106*
107*
108*
109*
5157291230
8944278480
9844100270
1157790580
1157790400
1157296890
1157795020
5157290530
9813250620
8941445880
1157290920
8971796700
1157259210
9813250300
9813254880
1157293010
1157290990
9813251730
1157290980
8970242390
8970242400
9813212050
9091854150
9813252100
1157795650
9813150650
1157795670
9019008180
1157795620
1835794920
1157290150
1157290380
1157791910
1157296360
1157795640
5157290990
SCREW
1
SPRING CAPSULE
1
NUT
1
NUT
1
NUT
1
NUT
1
SCREW
1
PLUG
2
PIN
1
GASKET
2
NUT
1
CAP
1
LEVER
1
KEY, 13MM
1
WASHER
AR
COLLAR
1
SHIM
1
SHIM
AR
SEAL
1
BUSHING
1
BUSHING
1
GASKET
2
RING
2
CAP
1
CAP
1
ADAPTER
1
ADAPTER
1
BOLT, M8X18 ..............................1 ...................... W/LOCK WASHER
BOLT
1
WASHER
1
GASKET
1
PLUG
1
BRACKET
1
LIMITER
1
CAP NUT
1
GASKET
2
110*
111G*
111H*
112*
113*
158*
145*
150F*
150G*
151*
154*
156*
160*
161*
196*
253*
352*
429*
QTY.
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 151
ISUZU 6BG1 —FEED PUMP ASSY.
FEED PUMP ASSY.
PAGE 152 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — FEED PUMP ASSY.
FEED PUMP ASSY.
NO.
1
2*
3*
4*
5*
7*
10*
11*
12*
13*
15*
16*
17*
18*
19*
28*
29*
30*
31*
PART NO.
1157501620
1157610060
1196230160
9813517020
1157550020
1196230160
1157590030
1096750630
1096300850
9813550250
5157510120
9813512050
9813513020
9813550350
8941711850
5157540010
9813514030
9813514100
1157590020
PART NAME
QTY.
REMARKS
PUMP ASSY. .................................. 1 .................. INCL. ITEMS W/*
PUMP
1
GASKET
1
VALVE SPRING
2
PUMP VALVE
2
GASKET
2
ADAPTER
1
BOLT
1
GASKET
2
SNAP RING
2
HOUSING
1
PISTON
1
SPRING
1
GASKET
1
PLUG
1
TAPPET ASSY.
1
ROLLER
1
PIN
1
GUIDE
2
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 153
ISUZU 6BG1 — MISC. INJECTION PUMP ASSY.
MISC. INJECTION PUMP ASSY.
PAGE 154 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — MISC. INJECTION PUMP ASSY.
MISC. INJECTION PUMP ASSY.
NO.
2
3*
8
9
10
PART NO.
1197510490
9041010300
9091645100
9091506100
5156390020
PART NAME
QTY.
REMARKS
BRACKET ................................. 1 ................ INCL. ITEM W/*
STUD
4
PLAIN WASHER
4
LOCK WASHER
4
NUT
4
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 155
ISUZU 6BG1 — COUPLING ASSY,
COUPLING ASSY.
PAGE 156 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — COUPLING ASSY.
COUPLING ASSY.
NO.
1
2
3
4
5
27
30
PART NO.
5157810030
9096620070
9884105020
1156192470
5156190480
1125240150
8944575170
PART NAME
COUPLING
BOLT
NUT
PLATE
WASHER
GEAR
BOLT
QTY.
1
1
1
1
1
1
6
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 157
ISUZU 6BG1 — WATER SEDIMENTER ASSY.
WATER SEDIMENTER ASSY.
PAGE 158 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — WATER SEDIMENTER ASSY.
WATER SEDIMENTER ASSY.
NO.
1
4*
5*
7*
9*
19
20
33*#
34*
36*
38*
44
45
46
47
56*
PART NO.
1132008410
5132120591
5096230700
5132190200
5096300240
1197550921
0280808250
8944163770
8944537460
5132190221
5132190210
5154112231
1096750860
1096300850
1154143741
1132112110
PART NAME
QTY.
REMARKS
FUEL SEDIMENTER ................. 1 ................. INCL. ITEMS W/*
COVER
1
GASKET
1
PLUG
1
GASKET
1
BRACKET
1
BOLT, M8X25 FLANGE
2
WASHER
1
PLUG ......................................... 1 ................ INCL. ITEMS W/#
RING
1
FLOAT
1
PIPE
1
BOLT, M14X27
2
GASKET
4
PIPE
1
CASE
1
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 159
ISUZU 6BG1 — SWITCH AND RELAY ASSY.
SWITCH AND RELAY ASSY.
PAGE 160 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
ISUZU 6BG1 — SWITCH AND RELAY ASSY.
SWITCH AND RELAY ASSY.
NO.
4
63
244
417
PART NO.
1858886780
1823100080
1823200010
1825500732
PART NAME
LABEL, ENGINE MAINT.
SWITCH ASSY.
BATTERY SWITCH
EMERGENCY RELAY
QTY.
1
1
1
1S
REMARKS
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 161
TERMS AND CONDITIONS OF SALE — PARTS
Effective: July 1, 2000
4.
PAYMENT TERMS
Terms of payment for parts are net 10 days.
FREIGHT POLICY
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and the
carrier.
Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
5.
Parts must be in new and resalable
condition, in the original Multiquip package
(if any), and with Muiltiquip part numbers
clearly marked.
6.
The following items are not returnable:
a.
Obsolete parts. (If an item is listed
in the parts price book as being
replaced by another item, it is
obsolete.)
b.
Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
MINIMUM ORDER
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c.
Any line item with an extended dealer
net price of less than $5.00.
PRICING AND REBATES
Prices are subject to change without prior
notice. Price changes are effective on a specific
date and all orders received on or after that date
will be billed at the revised price. Rebates for
price declines and added charges for price
increases will not be made for stock on hand
at the time of any price change.
Multiquip reserves the right to quote and sell
direct to Government agencies, and to Original
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
SPECIAL EXPEDITING SERVICE
A $20.00 to $50.00 surcharge will be added to
the invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
d.
Special order items.
RETURNED GOODS POLICY
e.
Electrical components.
Return shipments will be accepted and credit
will be allowed, subject to the following
provisions:
f.
Paint, chemicals, and lubricants.
LIMITATIONS OF SELLER’S LIABILITY
g.
Decals and paper products.
1.
h.
Items purchased in kits.
Multiquip shall not be liable here under for
damages in excess of the purchase price of the
item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
2.
A Returned Material Authorization must
be approved by Multiquip prior to shipment.
To obtain a Return Material Authorization,
a list must be provided to Multiquip Parts
Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
a.
b.
The list must be typed or computer
generated.
c.
The list must state the reason(s) for
the return.
d.
The list must reference the sales
order(s) or invoice(s) under which
the items were originally purchased.
e.
3.
The parts numbers and descriptions
must match the current parts price
list.
The list must include the name and
phone number of the person
requesting the RMA.
A copy of the Return Material
Authorization must accompany the return
shipment.
7.
The sender will be notified of any material
received that is not acceptable.
8.
Such material will be held for 5 working
days from notification, pending
instructions. If a reply is not received
within 5 days, the material will be returned
to the sender at his expense.
9.
Credit on returned parts will be issued at
dealer net price at time of the original
purchase, less a 15% restocking charge.
10. In cases where an item is accepted for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
11. Credit issued will be applied to future
purchases only.
LIMITATION OF WARRANTIES
No warranties, express or implied, are made
in connection with the sale of parts or trade
accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes not
authorizes any person to assume for it any
other obligation or liability whatever in
connection with the sale of its products. A part
from such written statement of warranty, there
are no warranties, express, implied or statutory,
which extend beyond the description of the
products on the face hereof.
PAGE 162 — DCA-60SSI2 — PARTS AND OPERATION MANUAL — REV. #3 (09/15/01)
NOTE PAGE
DCA-60SSI2 — PARTS AND OPERATION MANUAL— REV. #3 (09/15/01) — PAGE 163
PARTS AND OPERATION MANUAL
PARTS AND OPERATION MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL NUMBER
ON-HAND WHEN CALLING
© COPYRIGHT 2001, MULTIQUIP INC.
PAR
TS DEP
AR
TMENT
ARTS
DEPAR
ARTMENT
800/427-1244 or 310/537-3700
FAX: 800/672-7877 or 310/637-3284
VICE DEP
AR
TMENT
SER
DEPAR
ARTMENT
SERVICE
800/835-2551 or 310/537-3700
FAX: 310/638-8046
WARRANTY DEP
AR
TMENT
DEPAR
ARTMENT
800/835-2551 or 310/537-3700
FAX: 310/638-8046
MAIN
800/421-1244 or 310/537-3700
FAX: 310/537-3927
MULTIQUIP INC.
PARTS DEPARTMENT:
18910 WILMINGTON AVE.
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
SERVICE DEPARTMENT:
310-537-3700
800-421-1244
800-835-2551
FAX: 310-537-3927
FAX: 310-638-8046
E-mail:[email protected] • www:multiquip.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement