SecurityMan ClearCam User guide

SecurityMan ClearCam User guide
SecurityMan
®
ClearCam II
Wi-Fi Interference Free Wireless Outdoor/Indoor
Color Camera Kit with Night Vision/Audio
User Guide
Copyright Notice
This manual is furnished under license and may be used or copied only in accordance with the
terms of such license. Except as permitted by such license, no part of this publication may be
reproduced, stored in a retrieval system, or transmitted, in any form or any means, electronic,
mechanical, recording, or otherwise, including translation to another language or format, without
the prior written permission of SecurityMan.
The content of this manual is furnished for informational use only, is subject to change without
notice, and should not be construed as a commitment by SecurityMan. SecurityMan assumes no
responsibility or liability for any errors or inaccuracies that may appear in this book.
All other product names, trademarks and registered trademarks in this document are the properties of their respective holders.
FCC Information
Notes on FCC’s “Consistent Statement of Information” This product meet the requirements specified in Part 15 of FCC Regulation. Operation rests with the following two conditions:
(1) The equipment should not cause any harmful interference.
(2) The equipment must receive and process any interference, including any possible interference
caused by operation mistakes.
After testing the product, we confirm that the camera complies with the provision for class C digital
equipment in the 15th part in FCC regulations; and the receiver complies with the limitations for
class B digital equipment in Part 15 of FCC regulation. The product generates, applies and emits
radio waves. It might cause harmful interferences to wireless communication if not be installed and
used following the description of the manual.
The product may cause interference in residential area, and the customer should take remedies to
eliminate the interference on their own costs.
If the product causes any harmful interference to wireless equipment or disturbs the receiving of
TV signals (it can be identified by turning on and off the product), you can solve the trouble by following methods:
- Readjust the product or put it in another place.
- Extend the distance between the equipment interfered and the product.
- Refer to dealers or experienced radio electrician for help.
3
Warranty
SecurityMan warrants that this product will be free from defects in materials and workmanship for
period of time specified on the product packaging. This limited warranty shall commence from the
date of purchase. SecurityMan Products warranty is not transferable and is limited to the original
purchaser. If the product is found to be defective then, as your sole remedy and as the manufacturer's only obligation, SecurityMan will repair or replace the product . This warranty shall not apply
to products that have been subjected to abuse, misuse, abnormal electrical or environmental conditions, normal wear and tear or any condition other than what can be considered normal use.
Limitation of Liability
The liability of SecurityMan arising from this warranty and sale shall be limited to a refund of the
purchase price. In no event shall SecurityMan be liable for costs of procurement of substitute products or services, or for any lost profits, or for any consequential, incidental, direct or indirect damages, however caused and on any theory of liability, arising from this warranty and sale. These
limitations shall apply not with standing any failure of essential purpose of any limited remedy.
SecurityMan
4601 E. Airport Drive, Ontario, CA 91761, USA
Tel: 888-977-3777 or 909-230-6668
Fax: 909-230-6889
Email: [email protected]
Website: http://www.securitymaninc.com
Copyright 2007 by SecurityMan v1.0
4
Notice:
0.9GHz wireless camera works at ISM band. It may cause interferences with
other wireless equipment that operates at the same band. Please turn off one
of the equipment to eliminate the interference.
Product Assurance
0.9GHz wireless camera will emit electromagnetic wave, just like other wireless products. But the output power of the products is lesser than other wireless products such as mobile phones. The0.9GHz wireless camera meets
wireless frequency security standards and recommend indexes while working. These standards and indexes are certificated by academic organization
and represent the cogitative research of the scientific workers who continuously explore and annotate the involved fields. So we believe that our products are safe for customers.
Operating Restrictions
DO NOT use this product to violate one's privacy. Monitoring one's activities
without consent is illegal and this product is not designed and manufactured
for these purposes.
DO NOT put this product near any medical equipment. Radio waves might
potentially cause breakdown of electrical medical equipment. This product
should be placed at least 1 feet away from any heart pacemaker. Radio
waves might potentially influence heart pacemaker and lead to respiratory
disturbance.
DO NOT use this product for any illegal activities. SecurityMan shall not be
responsible for any consequences of illegal conducts by users.
5
Conditions
Please read the following messages to make sure whether your working environment is suitable.
• Ensure there is enough space around the receiver for ventilation.
• The temperature should be kept between –10˚C and 50˚C (-14˚F – 122˚F).
The relative humidity should remain from 20% to 80%.
• Avoid putting the product in places where occur might change rapidly in
temperature or humidity
• Keep it dry, dustless and avoid exposure in it directly in sunlight
• Keep product away from heat sources such as electric heater
• Do not use the camera near aggressive chemicals
• Do not place product near any magnetic objects
Maintenance
It might influence the normal operation of the product if used at the fringe
range of normal temperature. Please turn off the power when not in use
Do not disassemble the product.
Do not shake or stricken the product.
Do not use this camera near water- for example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet basement or near a swimming pool; and
the like.
Please obey the local government’s environment protection policy
6
Warning:
• In order to avoid inflammation or electric shock, this machine should be kept
away from exposure to rain or moist, and it shall not be put in or near bathrooms, washing pools, washhouses, moist basements, or swimming pools.
• In use of sockets set on walls or extension wires, attention should be paid
not to exceed their load capabilities to avoid inflammation or electric shock;
• Casings are not allowed to open, otherwise the internal precision parts may
get damaged, or personal injury caused.
• Switch off the power supply in thunder and lightning or when not in use for
long periods of time.
• Do not attempt to service the product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
Important Information
The user’s manual provides important information for customers to use their
products properly, and avoid possible injuries and damages.
The condition of being susceptible to harm or injury
A careful attention to the probable effects of an act, in
order that failure or harm may be avoided
A notification or communication of a fact, claim,
demand, or proceeding
Information about a particular subject
Something that should not be done
7
DO NOT put the package plastic bags in
reach of children or babies.
*It might cause asphyxia if children or babies
putting the bags into their mouths.
DO NOT plug the AC adapter into the outlet in improper situation.
*Plugging AC adapter with wet hand might
cause electric shock. Plugging AC adapter
unsteadily might cause fire or electric shock.
DO NOT cover the AC adapter when it is
connected to power socket, place the
adapter near heaters, and put it on the
floor that is equipped with a heater.
*The above-mentioned operation might cause
fire or incidents.
DO NOT use it on airplanes. Please abide
by the airways provision.
*It might influence the communication aboard
and the flying apparatus if departing from the
airways regulation. This will result in accident,
possible death and severe physical hurt.
DO NOT put the camera in the wet place
where water might splash or where rainwater and mist might erode.
*This place might cause fire, shock, short circuit, etc.
8
DO NOT disassemble or repair the camera, the receiver and other relevant peripheral equipment.
*Improper disassembly might cause damages
to the product or the peripheral equipment.
DO NOT use the receiver on the surface of
thermo labile material.
*Please embed thermal insulating material
when using on the surface of the thermo
labile material.
DO NOT place or use the AC adapter on
temperature sensitive materials.
*The above practice might cause the plastic
distortion, fading or sticking on the surface.
DO NOT touch, shake or hold the aerial.
*Touching, shaking or holding the aerial might
influence the receiving of electromagnetic
wave, and thereby influence the receiving
effect.
DO NOT use several cameras with neighboring frequency closely at the same time
*The electromagnetic wave signal of the
neighboring frequency might cause slight
interferences and influence the receiving
effect.
9
DO NOT let several cameras with same
frequency work at the same time.
*The overlap of the electromagnetic wave signal of the same frequency might cause
severe interferences and unable to receive
signals.
Please adjust the brightness on TV or on
monitor to achieve optimum efficiency.
*There are slight differences of brightness
among cameras which can be adjusted
DO NOT use the camera in complex environment. The obstruction of stumbling
block will affect the electromagnetic wave
and influence the receiving range.
*Wall, tree and other stumbling block might
absorb, reflect the electromagnetic wave and
influence the receiving range.
DO NOT use the camera in the places that
are covered by metal.
*Places surrounded by metal, such as elevator and cabinet, might shield the electromagnetic wave resulting in signal lost.
10
Contents
Introduction
Package Contents
Technical Support
12
12
12
Product Basics
Camera
Receiver
Dip-Switch(Camera)
Receiver manual & loop switch
13
13
13
14
15
Installation Diagram
16
Installation
A) Setting up the Antennas
B) Setting up the Camera
C) Setting up the Receiver for manual or loop mode
D) Setting up the Receiver with TV/Monitor/VCR/DVR
16
17
17
18
Specification
19
Troubleshooting
20
11
Introduction
Thank you for purchasing ClearCam II. ClearCam II is a convenient
wireless security camera kit for any outdoor/indoor surveillance of a
home or a business. It consists of a wireless camera, a receiver, and
needed accessories.
Note: Please read the manual entirely before using the product.
Package contents:
• 1 x Wireless outdoor/indoor color camera (SM-8123T) with bracket
• 1 x 2-CH 0.9GHz wireless receiver (SM-7034) and antenna
• 1 x 12V power AC adapter (for camera)
• 1 x 8V power AC adapter (for receiver)
• 1 x AV cable
• 1 x Accessories
Technical Support
In U.S.A, please call 1-909-230-6668 or in other areas,
E-mail us at: [email protected]
Product Basics
Camera
Dip-Switch
1
OG
ON
2
GD
H0
Antenna
2
Microphone
Built-in
Sunshade
Infrared LEDs
for night vision
Bracket
(with 2 adjustable
viewing angle)
Power Jack
Receiver
Antenna
Power Socket
LED channel Indicator
DC8V
MANUAL
CH2
CH1
SET
Channel Button
(manual mode)
LOOP
Manual/Loop
Switch
A/V
Audio/Video Output
13
Dip-Switch (Camera)
To adjust the dip-switch channel for the camera, unscrew to remove the
front portion of the camera.
1
OG
1
2
OG
ON
2
GD
H0
2
Use a pointed object to set the dip-switch to desired channel
1
OFF
ON
2
OFF
OFF
OFF
3
4
ON GDH02
OG
ON
CH1 = 906MHz
1 2
ON GDH02
OG
ON
ON
Channel
1 2
CH2 = 924MHz
ON GDH02
OG
2
1 2
N/A
ON GDH02
OG
1
1 2
N/A
14
Receiver manual & loop switch
LED channel Indicator
CH2
CH1
SET
Channel Button(manual mode)
A) In manual mode use the channel button "SET" to toggle between
channel #1 & channel #2.
B) In loop mode the receiver will auto dwell by switching between
channel #1 & channel #2. The auto dwell time is fixed and preset
to 5 second intervals.
Sunshade
A
B
For outdoor use, you should attach the sunshade to reduce sun reflection (A). For indoor use, please detach the sunshade from the camera to
prevent dark images. (B)
15
Installation Diagram
VCR/DVR
Or
A / V Cable
CH4
AC
adapter
CH2
CH1
SET
WARNING: When using power adapter, make sure the voltage indications on the adapters are compatible to the devices to avoid potential
damages for incorrect usage of power.
Installation
A) Setting up the Antennas
Connect the antennas to the receiver and camera
CH2
CH1
SET
16
B) Setting up the Camera
1)
2)
3)
4)
5)
Set the camera to desired Dip-Switch Channel Frequency
Place the camera in a desired location.
Plug the power adapter jack into the power jack
Plug the power adapter to any AC/DC outlet
Jot down the Dip-Switch Channel of each camera. (The receiver
will receive signal from the corresponding camera and display
one at the time. For example, Channel 1 light on the receiver will
display the image from Camera 1 only).
Default Mode
1
OG
1
2
OG
ON
2
GD
H0
2
Power Jack
C) Setting up the Receiver for manual or loop mode
1)
Basically, the receiver is already set to match the camera by
default(CH1 & Manual). To setup "Loop" mode the A B switch
to "Loop" located at the rear of the receiver.
Note: only use "Loop"mode if two cameras are in used.
17
D) Setting up the Receiver with TV/Monitor/VCR/DVR
1)
2)
3)
Connect one end of the A/V cable to the A/V out jacks of the
Receiver. Connect the other end to your TV/Monitor A/V jacks.
Plug the Receiver’s Power Supply (8V DC Adapter) into any wall outlet and plug its jack into the Receiver.
Position the Receiver in a convenient location
Connect to 8V DC Adapter
TV/ Monitor
A/V Cable
Connect to 8V DC Adapter
A/V Cable
VCR/DVR
Output to TV
18
RECEIVER(SM-7034)
CAMERA(SM-8123T)
Specification
Item
Imaging Senor
Total Pixels
Minimum illumination
Transmission Frequency
Transmission Power
Modulation Type
Bandwidth
Power Supply
Consumption Current
Unobstructed Effective Range
Night Vision Range
Dimension(WxDxH)
Weight
Receiving Frequency
Intermediate Frequency
Demodulation Type
Antenna
Receiving Sensitivity
Video Output Level
Audio Output Level
Power Supply
Consumption Current
Dimension(WxDxH)
Weight
Operating Temperature
Operating Humidity
Value
CMOS
510 x 492(NTSC)
OLux
ISM 906MHz & 924MHz (CH2, Manual/Loop)
10mW/CE: 2mW/FCC
FM
18MHz
±12VDC
90mA(IR OFF) & 260mA(IR ON)
100m
15m(45ft)
61x96x136(mm)(Including Bracket)
296g
ISM 900MHz ~ 930MHz
480MHz
FM
50ohmSMA
≤-85dBm
1.1V+/–0.2V @75 ohm,S/N>38dB
3.0V+/–1V @600 ohm
+8VDC
165mA
78x92x22(mm)(Excluding Antenna)
174g
-10˚C~50˚C/±14˚F~+122˚F
85%RH
pp
pp
19
Troubleshooting
Abnormal Phenomena
Possible Reasons/Solutions
*Check the camera / receiver is
connected to the power supplies,
and powered on.
*Check the channel of the receiver
to correspond with camera;
*Check the distance and blocks.
*Interfered by other sources;
*Check the distance and blocks.
*Mismatching system of PAL TV
and NTSC cameras or vice versa.
20
www.securitymaninc.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement