Yamaha TP-7029 Operating instructions

Yamaha TP-7029 Operating instructions
AUDIO/VIDEO MULTI-CHANNEL
RECEIVER
VSX-41
Operating Instructions
WARNING: TO PREVENT FIRE OR SHOCK HAZARD,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Thank you for buying this Pioneer product.
Please read through these operating instructions
so you will know how to operate your model
properly. After you have finished reading the
instructions, put them away in a safe place for future
reference.
IMPORTANT NOTICE
H006AEn
The serial number for this equipment is located in the
rear panel. Please write this serial number on your
enclosed warranty card and keep it in a secure area.
This is for your security.
Re-Equalization and the “Re-EQ” logo are
trademarks of LucasFilm Ltd.
Manufactured under license from
LucasFilm Ltd.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double D symbol are
trademarks of Dolby Laboratories.
“DTS”, “DTS-ES Extended Surround” and “Neo:6”
are trademarks of Digital Theater Systems, Inc.
Contents
1 Before you start
4 Controls and displays
Checking what’s in the box ...............................6
Installing the receiver ........................................6
Making cable connections ................................6
Loading the batteries .........................................6
Operating range of remote control unit ........... 6
Front panel ........................................................24
Display ............................................................. 25
Remote control ................................................ 27
2 5 minute guide
Introduction to home theater ............................7
Listening to Surround Sound ............................8
Using the Quick Setup ....................................12
3 Connecting up
Audio/Video cords ........................................... 13
S-video cables ...................................................13
Component video cords ................................. 13
Digital audio coaxial cords/
Optical cables ...................................................13
Connecting digital components .................... 14
Connecting audio components ......................15
Connecting DVD 5.1 channel components ... 16
Connecting video components ....................... 16
Connecting to the front panel
video terminal ............................................ 17
Connecting antennas ..................................... 18
FM wire antenna .........................................18
AM loop antenna ....................................... 18
Antenna snap connectors ........................ 18
Using external antennas ............................18
To improve FM reception ............................18
To improve AM reception ...........................18
Connecting the speakers ................................19
Speaker terminals ..................................... 20
A and B speaker systems ......................... 20
Hints on speaker placement .................... 20
Connecting additional amplifiers .................. 22
AC outlet .......................................................... 23
Operating other Pioneer components .......... 23
5 Playing sources
Introduction to Sound Modes ........................ 30
Stereo/Direct ...............................................30
Standard mode .......................................... 30
Advanced Surround modes ....................... 31
Choosing the input signal .............................. 32
Listening to multichannel playback .............. 32
Using Stereo/Direct .........................................33
Using Advanced Surround ............................. 33
Using Loudness and Midnight listening ........ 33
Using the tone controls .................................. 34
Playing other sources ..................................... 34
Selecting the multichannel analog inputs .... 35
Using Re-Equalization .....................................35
6 Setting up your receiver
Choosing your receiver setup ........................ 36
Speaker setting .......................................... 37
Surround back speaker
setting ......................................................... 37
6.1 channel setting .....................................38
Subwoofer setting ..................................... 38
Crossover frequency setting ......................38
LFE attenuator setting ................................39
Front speaker distance setting .................. 39
Center speaker distance setting .............. 39
Surround speaker distance setting .......... 39
Surround back speaker distance
setting ......................................................... 39
Dynamic range control setting .................. 40
Dual mono setting ..................................... 40
Component video input settings .............. 40
Surround back channel input
setting ......................................................... 40
Coaxial digital input settings .................... 41
Optical digital input settings .................... 41
Setting the relative volume level
of each channel ............................................... 42
7 Using the tuner
Listening to the radio ...................................... 43
Improving FM stereo sound .......................43
Tuning directly to a station ........................ 43
Saving station presets .....................................44
Naming station presets .................................. 45
Listening to station presets ............................ 45
8 Making a recording
Making an audio or a video recording .......... 46
Monitoring your recording ........................ 46
9 Controlling the rest of your system
Setting the remote to control
other components ........................................... 47
Selecting preset codes directly .......................47
Setting Up Using Full Library Search ............. 48
Searching for preset codes using
brand names ................................................... 49
Programming signals from other
remote controls ............................................... 49
Erasing one of the remote control
button settings ................................................ 50
Clearing all the remote control settings ........ 50
Direct function ................................................ 51
Confirming preset codes .................................51
Controls for TVs ............................................... 52
Controls for other components .......................53
Preset Code List ...............................................55
10 Additional information
Troubleshooting ............................................... 67
Specifications ...................................................69
Cleaning the unit ..............................................70
01
Before you start
Checking what’s in the box
Please check that you've received the following
supplied accessories:
• AM loop antenna
• FM wire antenna
• Dry cell batteries x 2 (AA size IEC LR6)
Incorrect use of batteries may result in such
hazards as leakage and bursting. Observe the
following precautions:
• Never use new and old batteries together.
• These operating instructions
• Insert the plus and minus sides of the
batteries properly according to the marks
in the battery case.
Installing the receiver
• Batteries with the same shape may have
different voltages. Do not use different
batteries together.
• Remote control
Please note the following points:
• Do not place objects
directly on top of this
unit. This prevents
proper heat dispersal.
• When installing on a
rack, shelf, etc., be sure to leave more than
8 inches (20 cm.) of space above the
receiver.
Making cable connections
Make sure not to
bend the cables over
the top of this unit (as
shown in the
illustration). If this
happens, the magnetic
field produced by the
transformers in this unit may cause a
humming noise from the speakers.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction’s rules
that apply in your country or area.
Operating range of remote
control unit
The remote control may not work properly if:
• There are obstacles between the remote
control and the receiver's remote sensor.
• Direct sunlight or fluorescent light is
shining onto the remote sensor.
• The receiver is located near a device that is
emitting infrared rays.
• The receiver is operated simultaneously
with another infrared remote control unit.
Loading the batteries
30
30
23ft (7m)
6
En
Dry cell batteries x 2 (AA size IEC LR6)
5 minute guide
02
Introduction to home theater
You are probably used to using stereo equipment to listen to music, but may not be used to home
theater systems that give you many more options (such as surround sound) when listening to
soundtracks.
Home theater refers to the use of multiple audio channels to create a surround sound effect,
making you feel like you're in the middle of the action or concert. The surround sound you get from a
home theater system depends not only on the speakers you have set up in your room, but also on
the source and the sound settings of the receiver.
DVD-Video has become the basic source material for home theater due to its size, quality, and ease
of use. Depending on the DVD, you can have up to seven different audio channels coming from one
disc, all of them being sent to different speakers in your system. This is what creates a surround
sound effect and gives you the feeling of ‘being there’.
This receiver will automatically decode Dolby Digital, DTS, or Dolby Surround DVD-Video discs,
according to your speaker setup. In most cases, you won’t have to make changes for realistic
surround sound, but other possibilities (like listening to a CD with multichannel surround sound)
are explained in Playing sources, starting on page 30.
7
En
02
5 minute guide
Listening to Surround Sound
This receiver was designed with the easiest possible setup in mind, so with the following quick
setup guide, you should have your system hooked up for surround sound in no time at all. In most
cases, you can simply leave the receiver in the default settings.
1
Hook up your DVD player.
For surround sound, you’ll want to hook up using a digital audio connection from the DVD player to
the receiver. You can do this with either a coaxial, or an optical connection (you don’t need to do
both). If you hook up using an optical cable, you should refer to Optical digital input setting on page
41 to assign the optical input to DVD.
Use a video cord to connect the video output on your DVD player to the receiver using the jacks
shown below.
2
Hook up your TV.
Use a video cord to connect your receiver to the TV using the jacks as shown below.
Optical cable
Coaxial cable
Note: If you hook up
using a optical cable,
see Optical digital
input settings on page
41 to assign the
optical input to DVD.
Video cord
DIGITAL IN
OPT
ASSIGNABLE
( DVD/ LD ) ¥
DIGITAL OUT
DVD
/ LD
FRONT
VIDEO OUT
S
IN
DIGITAL IN
D VIN D
ANTENNA
5.1CH
REC INPUT
CD-R AM IN
/ TAPE LOOP
FM
IN
/ MD UNBAL
75 Ω
¡¢
7
8
S - VIDEO
SURROUND
R
L
SURROUND
L BACK
R
TV /
SAT
DVD
/ LD
FRONT
IN
41
(DVD/ LD) ¥
CD
VCR /
DVR
IN
Î
3
VIDEO
OUT
IN
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
DVD PLAYER
0
(TV /
SAT )
OPT
This receiver
¥
OPT
DVD 7.1CH INPUT
CENTER SUB W.
AUX
IN
IN
STANDBY/ON
COAX
ASSIGNABLE
MONITOR
OUT
SUB
WOOFER
(CD)
ø
(TV /
SAT)
MONITOR
OUT
TV/
IN SAT
IN
DVD /
IN LD
CONTROL
R
AUDIO
L
DVD player
(CD-R/
/ TAPE
/ MD)
ø
1
DIGITAL OUT
OUT
2
PB
VIDEO
S
P
E
A
A
K
E
R
S
R
FRONT
PR
CENTER
L
OUT
MONITOR
OUT
SUB
WOOFER
PREOUT
VIDEO IN
TV
8
En
Video cord
PREOUT
( D V D / LD) IN ¥
L
L
SURROUND
BACK
MONITOR OUT
Y
OUT
VCR /
DVR
IN
PREOUT
PLAY
IN
¥
ASSIGNABLE
COMPONENT
VIDEO
Y
PB
(T V / SAT) IN ø
PR
R SURROUND BACK L
R
FRONT
R
SURROUND
CENTER
R SURROUND L
R
FRONT
L
5 minute guide
02
3
Connect your speakers.
A complete setup of eight speakers is shown here (including the subwoofer) but everyone’s home
setup will vary. Simply connect the speakers you have in the manner shown below. The receiver will
work with just two stereo speakers (the front speakers in the diagram) but using at least three
speakers is recommended, and a complete setup is best.
Make sure you connect the speaker on the right to the right terminal and the speaker on the left to
the left terminal. Also make sure the positive and negative (+/–) terminals on the receiver match
those on the speakers.
• Use speakers with a nominal impedance of 8 Ω to 16 Ω.
• If you’re not using a subwoofer, change the front speaker setting (see Speaker setting on
page 37) to large
• When using the speaker on your TV as the center speaker (C), connect the CENTER
PREOUT jack on this unit to the audio input jack on your TV. In this case the center speaker
shown is unnecessary.
Front
Left
Front
Right
Surround
Left
Center
DIGITAL IN
COAX
OPT
Surround
Right
Surround
Back Left
Surround
Back Right
OPT
ASSIGNABLE
ANTENNA
IN
AUX
IN
CD
DVD 7.1CH INPUT
CENTER SUB W.
(DVD/ LD) ¥
S - VIDEO
SURROUND
R
L
VCR /
DVR
AM
LOOP
SURROUND
L BACK
R
FM
UNBAL IN
75 Ω
TV /
SAT
IN
DVD
/ LD
FRONT
IN
IN
VIDEO
OUT
IN
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
MONITOR
OUT
SUB
WOOFER
(CD)
ø
(TV /
SAT)
MONITOR
OUT
TV/
IN SAT
DVD /
IN LD
CONTROL
R
AUDIO
OUT
L
(CD-R/
/ TAPE
/ MD)
ø
1
DIGITAL OUT
S
P
E
A
A
K
E
R
S
PREOUT
ASSIGNABLE
COMPONENT
VIDEO
2
( D V D / LD) IN ¥
L
SURROUND
BACK
L
MONITOR OUT
Y
OUT
VCR /
DVR
IN
PREOUT
PLAY
IN
¥
R
FRONT
PB
L
PR
CENTER
Y
PB
(T V / SAT) IN ø
PR
R SURROUND BACK L
R
FRONT
R
SURROUND
CENTER
R SURROUND L
R
FRONT
L
AC OUTLET
B
One Surround Back
Speaker (or passive
subwoofer)
SW
TV
INPUT
Powered subwoofer
Be sure to complete all
connections before
connecting this unit to
the AC power source.
9
En
02
5 minute guide
If you only have one surround back speaker connect as below. You could also use this method for a
subwoofer when using the surround back speaker terminal for a passive subwoofer.
Surround back
speaker (or
subwoofer)
R SURROUND BACK L
• Be sure to complete all connections before connecting this unit to the AC power source.
• If you are using only one surround back speaker, connect the positive wire to the right
channel (+) terminal, and the negative wire to the left channel (–) terminal (shown above).
• If you select subwoofer (SB SUBWF) in the Surround back speaker setting (see page 37) you
can hook up a subwoofer instead of speakers to the surround back speaker terminals. Connect
the wires just as above, connecting the positive wire to the right channel (+) terminal, and the
negative wire to the left channel (–) terminal.
10
En
5 minute guide
02
4
Plug in the receiver and switch it on, followed by your DVD player, your subwoofer and
the TV.
Make sure you’ve set the video input on your TV to this receiver. Check the manual that came with
the TV if you don’t know how to do this.
Also make sure that DVD/LD is showing in the receiver’s display, indicating that the DVD input is
selected. If it isn’t, press DVD/LD on the remote control to set the receiver to the DVD input.
5
Press QUICK SETUP on the front panel to specify your speaker setup and your room
size.
Use the MULTI JOG/INPUT SELECTOR dial to select and ENTER to confirm your selection. See
Using the Quick Setup on the next page if you’re unsure about the settings.
6
Play a DVD, and adjust the volume to your liking.
There are several other sound options you can select. See pages 30–31 for more on this. See also
Choosing your receiver setup on page 36–42 for more setup options.
Depending on your DVD player or source discs, you may only get digital 2 channel stereo and
analog sound. In this case, the listening mode must be set to Standard (it should already be
set—see page 32–33 if you need to do this) if you want multichannel surround sound.
11
En
02
5 minute guide
Using the Quick Setup
You can use the Quick Setup to get your system
up and running with just a few button presses.
The receiver automatically makes the necessary
settings after you have selected your speaker
setup and room size. If you want to make more
specific settings, refer to Choosing your receiver
setup on pages 36–42 Use the front panel
controls for the steps below.
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
Check the table below to find the speaker
setup that corresponds with your system.
N∫m-¯,
INPUT
SELECTOR
MULTI JOG
ENTER
MASTER VOLUME
ADVANCED
SURROUND
STEREO/
DIRECT
SIGNAL
SELECT
MIDNIGHT/
LOUDNESS
SPEAKERS
MONITOR
TONE
QUICK SETUP
UP
DOWN
MULTI JOG
LISTENING MODE
VIDEO INPUT
FL DIMMER
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
R
1
If the receiver is off, press STANDBY/
ON to turn the power on.
The STANDBY indicator goes out.
2
Press QUICK SETUP.
The display prompts you to select your speaker
setup.
3
Use the MULTI JOG/INPUT SELECTOR
dial to choose your speaker setup.
Cycle between the following choices:
4
Press ENTER.
The display prompts you to select your room
size.
5
Use the MULTI JOG/INPUT
SELECTOR dial to choose your room size.
Depending on the distance of your speakers
from the listening position, choose between
Small, Medium, or Large (see table below).
Front
Center
3.0ch
En
4.0ch
7.1ch
4.1ch
7.0ch
5.0ch
6.1ch
12
3.1ch
6.0ch
5.1ch
Surround
Surround Back
S
M
L
12 ft.
10 ft.
6 ft.
3 ft.
12 ft.
10 ft.
7 ft.
5 ft.
12 ft.
10 ft.
9 ft.
7 ft.
6
Press ENTER to confirm your setup.
The display shows the speaker setup and room
size that you have selected.
Connecting up
03
Before making or changing any connections, switch off the power and disconnect the power cord from
the AC wall outlet.
Audio/Video cords
Component video cords
Use audio/video cords (not supplied) to connect
the audio/video components and a video cord to
connect the monitor TV.
Use component video cords to get the best
possible color reproduction of your video
source. The color signal of the TV is divided into
the luminance (Y) signal and the color (PB and
PR) signals and then output. In this way,
interference between the signals is avoided.
Connect from the component video jacks on the
rear of the receiver to the component video
jacks on the video component you are hooking
up.
Connect red plugs to R (right), white plugs to L
(left), and the yellow plugs to VIDEO.
Be sure to insert completely.
R
L
VID
EO
Y
PB
S-video cables
Use S-video cables (not supplied) to get clearer
picture reproduction than regular video cords.
Connect from an S-video jack on the rear of the
receiver to an S-video jack on the video
component you are hooking up.
Be sure to insert completely.
Green
PR
Blue
Red
Digital audio coaxial cords/
Optical cables
Commercially available digital audio coaxial
cords (standard video cords can also be used)
or optical cables (not supplied) are used to
connect digital components to this receiver.
Be sure to insert completely.
Digital audio coaxial cord
(or standard video cord)
Optical cable
13
En
03
Connecting up
Connecting digital components
The easiest way to hook up this receiver for surround sound is to use a digital input. You can do this
by either coaxial or optical connections (you do not need to do both). The quality of these two types
of connections is the same but since some digital components only have one type of digital
terminal, it is a matter of matching like with like (for example, the coaxial output from the
component to coaxial input on the receiver). The VSX-41 has four digital inputs (two coaxial inputs
and two optical inputs). Connect your digital components to the rear panel as shown below. See
page 17 to connect the front panel optical input.
There are two digital output jacks which is marked DIGITAL OUT. If you connect this to the optical
input on a digital recorder (currently these include MD, DAT and CD-R) you can make direct digital
recordings with this unit.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the AC wall outlet.
The arrows indicate the direction of the audio signal.
Satellite
tuner
DIGITAL
OUT
DIGITAL
DIGITAL
IN
OUT
DIGITAL IN
COAX
OPT
CD recorder
OPT
ASSIGNABLE
ANTENNA
DVD 7.1CH INPUT
CENTER SUB W.
AUX
IN
(DVD/ LD) ¥
CD
IN
S - VIDEO
SURROUND
R
L
VCR /
DVR
AM
LOOP
SURROUND
L BACK
R
FM
UNBAL IN
75 Ω
TV /
SAT
IN
DVD
/ LD
FRONT
IN
IN
VIDEO
OUT
IN
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
MONITOR
OUT
SUB
WOOFER
(CD)
ø
(TV /
SAT)
MONITOR
OUT
PLAY
R
AUDIO
L
(CD-R/
/ TAPE
/ MD)
ø
1
DIGITAL OUT
TV/
IN SAT
DVD /
IN LD
PREOUT
OUT
S
P
E
A
A
K
E
R
S
PREOUT
ASSIGNABLE
COMPONENT
VIDEO
2
( D V D / LD) IN ¥
L
L
SURROUND
BACK
MONITOR OUT
Y
OUT
VCR /
DVR
IN
CONTROL
IN
¥
R
FRONT
PB
L
PR
CENTER
Y
PB
(T V / SAT) IN ø
PR
R SURROUND BACK L
R
FRONT
R
SURROUND
CENTER
DIGITAL
OUT
R SURROUND L
COAX
R
FRONT
CD player
L
AC OUTLET
B
DIGITAL OUT
COAX
DVD player
If you have an LD player, you need to make special connections to ensure you can play 2 RF
format LDs on your system. If this is the case, hook up your DVD/LD or LD player directly to an
RF demodulator using both the 2 RF output and either a coaxial or optical digital connection.
We also recommend hooking up your digital components to analog audio jacks as well. Make
sure the RF demodulator digital in switch is set correctly (optical or coaxial depending on the
connection). See the component's instruction manual if you are unsure about its input and
output jacks.
14
En
Connecting up
03
Connecting audio components
To begin set up, connect your analog audio components (such as a cassette deck) to the jacks. For
components you want to record with, you need to hook up four plugs to the receiver (a set of stereo
inputs and a set of stereo outputs), but for components that only play, you only need to hook up one
set of stereo plugs. You must also hook up your digital components to analog audio jacks if you want
to record to/from digital components (like an MD) to/from analog components. See the previous
page for more on digital connections.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the AC wall outlet.
The arrows indicate the direction of the audio signal.
OUTPUT
DIGITA
L
CD player
R
ASSIG
ANTENNA
DVD 7.1CH INPUT
CENTER SUB W.
AUX
IN
CD
IN
SURRO
R
AM
LOOP
TV /
SAT
IN
REC PLAY
L
SURRO
L BA
R
FM
UNBAL IN
75 Ω
CD-R/Tape/MD Deck
L
VCR /
DVR
DVD
/ LD
FRONT
IN
IN
OUT
IN
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
R
VIDEO
MONI
OUT
SUB
WOO
PREOU
PLAY
IN
R
AUDIO
L
15
En
03
Connecting up
Connecting DVD 7.1 channel components
If you prefer to use a separate component for decoding DVDs, you can connect a decoder or a DVD
player with multichannel analog outputs to the multichannel inputs of this receiver.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the AC wall outlet.
The arrows indicate the direction of the signal.
DIGITAL IN
COAX
OPT
OPT
ASSIGNABLE
ANTENNA
IN
AUX
IN
CD
DVD 7.1CH INPUT
CENTER SUB W.
(DVD/ LD) ¥
S - VIDEO
SURROUND
R
L
VCR /
DVR
AM
LOOP
SURROUND
L BACK
R
FM
UNBAL IN
75 Ω
TV /
SAT
IN
DVD
/ LD
FRONT
IN
IN
VIDEO
OUT
IN
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
MONITOR
OUT
SUB
WOOFER
(CD)
ø
(TV /
SAT)
MONITOR
OUT
PLAY
R
AUDIO
L
(CD-R/
/ TAPE
/ MD)
ø
1
DIGITAL OUT
TV/
IN SAT
DVD /
IN LD
PREOUT
OUT
S
P
E
A
A
K
E
R
S
PREOUT
ASSIGNABLE
COMPONENT
VIDEO
2
( D V D / LD) IN ¥
L
SURROUND
BACK
L
MONITOR OUT
Y
OUT
VCR /
DVR
IN
CONTROL
IN
¥
R
FRONT
PB
L
PR
CENTER
Y
PB
(T V / SAT) IN ø
PR
R SURROUND BACK L
R
R
SURROUND CENTER SURROUND
FRONT
OUTPUT
OUTPUT
SURROUND
FRONT
FRONT
R
L
R
L
L
R
R
L
SURROUND
BACK OUTPUT
L
SUB
WOOFER
OUTPUT
CENTER
OUTPUT
VIDEO
OUTPUT
AC OUTLET
B
R
DVD/multichannel decoder with
7.1 channel analog output jacks
• The multichannel input can only be used when DVD 7.1 CH is selected (see page 35).
• If the component you are connecting only has one surround back channel output, change the
Surround back channel input setting (page 40) to SB 1ch IN.
Connecting video components
Connect your video components to the jacks as shown below. With digital video components (like a
DVD player), you must use one of the connections shown on the next page for the video signal, but
in order to hear a digital source (like a DVD) you should hook up the audio to a digital input (see
page 14). It is also a good idea to hook up your digital components with analog audio connections
(see page 15).
For better quality video, you can hook up using the component video jacks or the S-video jacks
(quality descends in this order) on the rear of the receiver instead of the regular video jacks (see the
second illustration of the following page). Make sure they are connected to the video component
using the same kind of connection. However, you don’t need to make more than one type of video
connection.
When connecting your equipment, always make sure the power is turned off and the power cord is
disconnected from the AC wall outlet.
16
En
Connecting up
03
Video deck
The arrows indicate the direction of the signal.
INPUT
OUTPUT
DIGITAL IN
VIDEO
ANTENNA
DVD 7.1CH INPUT
CENTER SUB W.
AUX
IN
L
TV tuner (or
Satellite tuner)
OUTPUT
VIDEO
VIDEO
L
L
R
R
ASSIGNABL
(DVD
CD
IN
SURROUND
R
R
L
VCR /
DVR
AM
LOOP
SURROUND
L BACK
R
FM
UNBAL IN
75 Ω
OUT
DVD
/ LD
FRONT
IN
VIDEO
IN
TV /
SAT
IN
IN
MONITOR
OUT
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
OUTPUT
VIDEO
INPUT
SUB
WOOFER
PREOUT
VIDEO
PLAY
IN
R
AUDIO
L
L
DVD or LD player
R
TV (monitor)
VIDEO IN
VIDEO
COMPONENT
TV (monitor)
Y
DIGITAL IN
COAX
OPT
OPT
ASSIGNABLE
S-VIDEO
PB
ANTENNA
PR
IN
AUX
IN
CD
DVD 7.1CH INPUT
CENTER SUB W.
(DVD/ LD) ¥
S - VIDEO
SURROUND
R
TV /
SAT
IN
IN
R
ø
(TV /
SAT)
MONITOR
OUT
OUT
MONITOR
OUT
TV/
IN SAT
SUB
WOOFER
DVD /
IN LD
PREOUT
CONTROL
OUT
PLAY
IN
R
AUDIO
¥
(CD-R/
/ TAPE
/ MD)
ø
1
DIGITAL OUT
L
S
P
E
A
A
K
E
R
S
ASSIGNABLE
COMPONENT
VIDEO
2
( D V D / LD) IN ¥
L
MONITOR OUT
Y
OUT
VCR /
DVR
IN
VIDEO
IN
IN
DVD
/ LD
FRONT
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
STEREO
L
DVD or LD player
SURROUND
L BACK
R
FM
UNBAL IN
75 Ω
ANALOG
L
VCR /
DVR
AM
LOOP
(CD)
R
FRONT
PB
L
PR
CENTER
Y
PB
(T V / SAT) IN ø
PR
R
FRONT
R SURROUND BACK L
VIDEO
COMPONENT
VIDEO
OUT
Y
PB
S-VIDEO
PR
Connecting to the front panel
video terminal
Front video connections are accessed via the
front panel input selector as VIDEO. There are
standard audio/video jacks as well as an
S-video jack and an optical input jack. Hook
them up the same way you made the rear panel
connections.
REO/
ECT
SIGNAL
SELECT
MIDNIGHT/
LOUDNESS
SPEAKERS
MONITOR
TONE
QUICK SETUP
MULTI JOG
VIDEO INPUT
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
R
Video
camera
(etc.)
VIDEO INPUT
DIGITAL OUT
V
L
R
17
En
03
Connecting up
Connecting antennas
Antenna snap connectors
Connect the AM loop antenna and the FM wire
antenna as shown below. To improve reception
and sound quality, connect external antennas
(see Using external antennas below). Always
make sure that the receiver is switched off and
unplugged from the wall outlet before making
or changing any connections.
Twist the exposed wire strands together and
insert into the hole, then snap the connector
shut.
3/8 in. (10mm)
AM LOOP
ANTENNA
Using external antennas
To improve FM reception
Connect an external FM antenna.
FM
UNBAL
75Ω
FM WIRE
ANTENNA
FM wire antenna
Connect the FM wire antenna and fully extend
vertically along a window frame or other
suitable area, etc.
AM loop antenna
Assemble the antenna and connect to the
receiver. Attach to a wall, etc. (if desired) and
face in the direction that gives the best
reception.
75 Ω coaxial cable
FM
ANTENNA
To improve AM reception
Connect a 15-18 feet length of vinyl-coated wire
to the AM antenna terminal without disconnecting the supplied AM loop antenna.
For the best possible reception, suspend
horizontally outdoors.
Outdoor antenna
Indoor
antenna
(Vinylcoated
wire)
18
En
15-18 ft. (5–6m)
AM LOOP
ANTENNA
Connecting up
03
Connecting the speakers
A complete setup of eight speakers (including the subwoofer) is shown below, but everyone’s home
setup will vary. Simply connect the speakers you have in the manner shown below. The receiver will
work with just two stereo speakers (the front speakers in the diagram) but using at least three
speakers is recommended, and a complete setup is best for surround sound. If you’re not using a
subwoofer, change the front speaker setting (see Speaker setting on page 37) to large.
Make sure you connect the speaker on the right to the right terminal and the speaker on the left to
the left terminal. Also make sure the positive and negative (+/–) terminals on the receiver match
those on the speakers.
Use speakers with a nominal impedance of 8 Ω to 16 Ω.
Front Speakers
Front
Left
Surround Speakers
Center Speaker
Front
Right
Surround
Left
Center
DIGITAL IN
COAX
OPT
Surround Back Speakers
Surround
Right
Surround
Back Left
Surround
Back Right
OPT
ASSIGNABLE
ANTENNA
DVD 7.1CH INPUT
CENTER SUB W.
AUX
IN
(DVD/ LD) ¥
CD
IN
S - VIDEO
SURROUND
R
L
VCR /
DVR
AM
LOOP
SURROUND
L BACK
R
FM
UNBAL IN
75 Ω
TV /
SAT
IN
DVD
/ LD
FRONT
IN
IN
VIDEO
OUT
IN
MONITOR
OUT
DVD
5.1CH
REC INPUT
IN
CD-R
/ TAPE
/ MD
SUB
WOOFER
(CD)
ø
(TV /
SAT)
MONITOR
OUT
TV/
IN SAT
DVD /
IN LD
CONTROL
R
AUDIO
OUT
L
(CD-R/
/ TAPE
/ MD)
ø
1
DIGITAL OUT
S
P
E
A
A
K
E
R
S
PREOUT
ASSIGNABLE
COMPONENT
VIDEO
2
( D V D / LD) IN ¥
L
SURROUND
BACK
L
MONITOR OUT
Y
OUT
VCR /
DVR
IN
PREOUT
PLAY
IN
¥
R
FRONT
PB
L
PR
CENTER
Y
PB
(T V / SAT) IN ø
PR
R SURROUND BACK L
R
FRONT
R
SURROUND
CENTER
R SURROUND L
R
FRONT
L
AC OUTLET
B
One Surround Back
Speaker (or passive
subwoofer)
SW
INPUT
Powered subwoofer
TV
Be sure to complete
all connections
before connecting
this unit to the AC
power source.
19
En
03
Connecting up
• When using the speaker on your TV as the center speaker (C), connect the CENTER PREOUT
jack on this unit to the audio input jack on your TV. In this case the center speaker shown is
unnecessary.
• If you are using only one surround back speaker, connect the positive wire to the right channel
(+) terminal, and the negative wire to the left channel (–) terminal (see illustration on page 10).
• If you select subwoofer (SB SUBWF) in the Surround back speaker setting (see page 37) you can
hook up a subwoofer instead of speakers to the surround back speaker terminals. Connect the
positive wire to the right channel (+) terminal, and the negative wire to the left channel (–)
terminal (see illustration on page 10).
Speaker terminals
3/8 in. (10 mm)
1
Twist exposed wire strands together.
2
Loosen speaker terminal and insert exposed wire.
3
Tighten terminal.
The speaker terminals also
accept single banana
plugs. (Refer to speaker
manual for details.)
Make sure that all the bare speaker wire is twisted together and inserted fully into the speaker
terminal. If any of the bare speaker wire touches the back panel it may cause the power to cut off as
a safety measure. Use good quality speaker wire to connect the speakers to the receiver.
A and B speaker systems
The receiver has two speaker systems: A and B. A is the main system supporting the full speaker
setup. If you switch on both A and B speaker systems, only the front speakers and the subwoofer
will be audible. No sound will come from the center, surround, or surround back speakers, but
multichannel sources will be down-mixed to the active speakers so no sound will be lost. Similarly, if
you choose just the B system you‘ll only hear the front speakers connected to the B system and
multi channel sources will be down-mixed to these two speakers.
Hints on speaker placement
Speakers are usually designed with a particular placement in mind. Some are designed to be
floorstanding, while others should be placed on stands to sound their best. Some should be placed
near a wall; others should be placed away from walls. We have provided a few tips on getting the
best sound from your speakers (below), but you should also follow the guidelines on placement that
the speaker manufacturer provided with your particular speakers to get the most out of them.
• Place the front left and right speakers at equal distances from the TV.
20
En
• When placing speakers near the TV, we recommend using magnetically shielded speakers to
prevent possible interference, such as discoloration of the picture when the TV is switched on. If
you do not have magnetically shielded speakers and notice discoloration of the TV picture, move
the speakers farther away from the TV.
Connecting up
• Place the center speaker above or below the
TV so that the sound of the center channel is
localized at the TV screen.
If you choose to install the center speaker
on top of the TV, be sure to secure it with
putty, or by other suitable means, to
reduce the risk of damage or injury
resulting from the speaker falling from
the TV in the event of external shocks
such as earthquakes.
• If possible, place the surround speakers
slightly above ear level.
03
Overhead view of speaker set up
Front
Left
Front
Right
Center
Subwoofer
Surround
Right
Surround
Left
Listening Position
Surround Back
Left
Surround Back
Right
• Try not to place the surround speakers
further away from the listening position than
the front and center speakers. Doing so can
weaken the surround sound effect.
• To achieve the best possible surround
sound, install your speakers as shown
below. Be sure all speakers are installed
securely to prevent accidents and improve
sound quality.
3-D view of speaker set up
21
En
03
Connecting up
Connecting additional amplifiers
This receiver has more than sufficient power for any home use, however it is possible to add
additional amplifiers to every channel. Make the connections shown below to add amplifiers to
power your speakers. Always make sure that the receiver is switched off and unplugged from the
wall outlet before making or changing any connections.
The arrows indicate the direction of the audio signal.
ANALOG IN
L
R
ANALOG IN
OPT
DIGITAL IN
OPT
ASSIGNABLE
ANTENNA
DVD 7.1CH INPUT
CENTER SUB W.
AUX
IN
(TV /
SAT)
IN
¥
(CD-R/ ø
/ TAPECD
/ MD)
1
DIGITAL OUT
RY
FM
UNBAL IN
75 Ω
IN
IN
IN
R
L
L
SURROUND
BACK
L
Surround channel
amplifier
R
S - VIDEO
MONITORSURROUND
OUT
R
L
VCR /
DVR
AM
LOOP
PREOUT
ASSIGNABLE
( D V D / LD) IN ¥
COMPONENT
(DVD/ LD) ¥
VIDEO
2
Front channel
amplifier
IN
R FRONT
S
TV /
SAT
P
IN
DVD
E
/ LD
FRONT
A
DVD
A
5.1CH
K
REC INPUT
IN
CD-R
E
/ TAPE
/ MD
R
S L PLAY
PB
LVIDEO
SURROUND
PLR BACK Y
CENTER
PB
(T V / SAT) IN ø
PR
R SURROUND BACK L
R
FRONT
R
SURROUND
CENTER
R SURROUND L
R
FRONT
ANALOG IN
Surround back
channel amplifier
ANALOG IN
Center channel
amplifier
L
OUT
AC OUTLET
MONITOR
OUT
SUB
WOOFER
PREOUT
B
AUDIO
INPUT
Powered
subwoofer
• To hear sound only from the pre-outs, disconnect any speakers that are connected directly to
the receiver.
• If you’re not using a subwoofer, change the front speaker setting (see Speaker setting on page
37) to large.
22
En
Connecting up
03
AC wall outlet
[switched 100 W (0.8 A) max]
Power supplied through this outlet is turned on and off by the
receiver's POWER switch. Total electrical power consumption of
connected equipment should not exceed 100 W (0.8 A).
AC OUTLET
SWITCHED
100 W MAX
0.8 A MAX
DO NOT CONNECT A MONITOR, TV SET, HEATER, OR SIMILAR
APPLIANCE TO THIS UNIT'S AC WALL OUTLET.
Do not connect appliances with high power consumption to the
AC WALL OUTLET in order to avoid overheating and fire risk.
This can also cause the receiver to malfunction.
• Make sure no exposed speaker wire is touching the rear panel, this may cause the receiver to
turn off automatically.
• This unit should be disconnected by removing the power plug from the wall socket when not in
regular use (ex. when on vacation).
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the
power cord when your hands are wet as this could cause a short circuit or an electric shock. Do not
place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in
the cord or tie it with other cords. The power cords should be routed such that they are not likely to
be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the
power cord once in a while. When you find it damaged, ask your nearest Pioneer authorized service
center or your dealer for a replacement.
Operating other Pioneer
components
By connecting a control cord (optional),
you can point the remote controls of other
Pioneer components at the receiver’s
remote sensor. The remote control signals
are received by the remote sensor of this
unit, and sent to the other devices via the
CONTROL OUT terminal.
CONTROL
IN
OUT CONTROL
OUT
Receiver
Other Pioneer products
with a control terminal
Remote
control unit
Connect to CONTROL
IN terminal of other
Pioneer products
with a control
terminal
23
En
04
Controls and Displays
Front panel
1
3
2
4
5
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
N∫m-¯,
INPUT
SELECTOR
MULTI JOG
ENTER
TM
STANDBY
STANDBY/ON
MASTER VOLUME
UP
DOWN
PHONES
7
6
8
9
STATION
TUNING
10
STANDARD
ADVANCED
SURROUND
11 12 13 14 15 16
STEREO/
DIRECT
SIGNAL
SELECT
MIDNIGHT/
LOUDNESS
SPEAKERS
MONITOR
TONE
QUICK SETUP
MULTI JOG
LISTENING MODE
VIDEO INPUT
TUNER EDIT
CLASS
BAND
MPX
Re-EQ
FL DIMMER
MULTI JOG
DIGITAL IN
S-VIDEO
24 23 22 21 20 19
1
STANDBY/ON
Switches the receiver between on and standby.
2
STANDBY indicator
Lights when the receiver is in standby.
3
Remote sensor
Receives the signals from the remote control.
4
ENTER button
5
MULTI JOG/INPUT SELECTOR dial
The MULTI JOG/INPUT SELECTOR dial
performs a number of tasks. Use it to select
options after pressing TONE CONTROL, QUICK
SETUP or TUNER EDIT.
6
MASTER VOLUME
7
PHONES jack
Use to connect headphones. When the
headphones are connected, there is no sound
output from the speakers.
24
En
18
VIDEO
L
AUDIO
R
17
8
STATION (+/–) buttons (pages 44–45)
Selects station presets or characters for those
presets when using the tuner.
9
TUNING buttons (page 43)
Selects the frequency when using the tuner.
10
LISTENING MODE buttons
STANDARD (pages 30, 32,33)
Press for Standard decoding and to switch
between the various Pro Logic II options.
ADVANCED SURROUND (pages 31, 33)
Use to switch between the various
surround modes.
STEREO/DIRECT (pages 30, 33)
Switches direct playback on or off. This
bypasses the tone controls and channel
levels for the most accurate reproduction
of a source.
Controls and Displays
04
19 FL DIMMER
Use this button to make the fluorescent display
(FL) dimmer or brighter.
11 SIGNAL SELECT (pages 32, 35, 46)
Use to select an input signal.
12 MIDNIGHT/LOUDNESS (page 33)
Use Midnight when listening to movie
soundtracks at low volume. Use Loudness to
boost the bass and treble at low volume.
20 Re-EQ (page 41)
This feature compensates for the effect of
reproducing sounds that have been originally
processed for a large movie theater in a smaller
room.
13 SPEAKERS
Use to cycle through the speaker
system: A = B = A+B
21 MPX (page 43)
Press to receive a radio broadcast in mono.
14 MONITOR
Press to switch tape monitoring on/off.
22 BAND (page 43)
Switches between AM and FM radio bands.
15 TONE
Press this button to access the bass and treble
controls, which you can then adjust with the
MULTI JOG/INPUT SELECTOR dial.
16
QUICK SETUP
17
VIDEO INPUT (page 17)
18
DIGITAL IN (page 17)
23 CLASS (pages 44–45)
Switches between the three banks (classes) of
station presets.
24 TUNER EDIT (pages 44–45)
Press to memorize and name a station for recall
using the STATION +/– buttons or the MULTI
JOG/INPUT SELECTOR dial.
Display
1
2
3
11 12
1
SIGNAL SELECT indicators
Lights to indicate the type of input signal
assigned for the current component:
AUTO
Lights when AUTO signal select is on
4
5 6
13
7
14
8
9
10
15
16
SB
Depending on the source, this lights when
a signal with surround back channel
encoding is detected.
DIGITAL
Lights when a digital audio signal is
detected.
25
En
04
Controls and Displays
2 DIGITAL
Lights when a Dolby Digital signal is
detected.
10 Speaker indicator
Shows the speaker system currently in use.
11
ANALOG
Lights when an analog signal is detected.
DTS
Lights when a source with DTS audio
signals is detected.
2
DTS
When the Standard mode of the receiver is on,
this lights to indicate decoding of a DTS signal.
3
2 DIGITAL
When the Standard mode of the receiver is on,
this lights to indicate decoding of a Dolby
Digital signal.
14 LOUDNESS
Lights when LOUDNESS has been selected.
15
TUNER indicators
STEREO:
Lights when a stereo FM broadcast is being
received in auto stereo mode.
MONO:
Lights when the mono mode is set using the
5
ATT
Lights when INPUT ATT is used to attenuate
(reduce) the level of the analog input signal.
TUNED:
Lights when a broadcast is being received.
6
RE-EQ:
Lights when Re-Equalization is swiched on. This
feature evens out the soudn for smaller rooms.
16 Master volume level
Shows the overall volume level. ---dB indicates
the minimum level, and -0dB indicates the
maximum level.
8
MIDNIGHT
Lights during Midnight listening.
9
MONITOR
Lights when MONITOR is selected (page 46).
En
13 ADV. SURR (Advanced Surround)
Lights when one of the Advanced Surround
modes has been selected.
4
2 PRO LOGIC II
When the Standard mode of the receiver is on,
this lights to indicate Pro Logic II decoding.
7
DIRECT
Lights when source direct playback is in use.
This function bypasses all tone, balance,
Advanced Surround, and Dolby Surround
effects.
26
Character display
12 Neo:6
Lights during NEO:6 processing
MPX button.
Depending on your level settings for each
channel, the maximum level can range between
–10dB and –0dB.
Controls and Displays
Remote control
13
LEARN ERASE
5
6
DVD
SEARCH BY BRAND
TV
VCR
7
TUN
CD
1
2
TEST TONE
INPUT ATT
4
5
FL DIMMER
6
LEVEL
8
7
9
+10
EFFECT
0
9
10
11
DISPLAY
DISC
MPX/RETURN
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
¡
4
¢
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
REMOTE SETUP
INPUT SEL.
CHARACTER display (LCD)
Shows function modes and other information.
ENTER
DTV INFO
TOP MENU
4
SETUP
Indicates that the remote is in Setup
mode so that new information (preset
codes, learning, etc.) can be input (see
pages 47–51).
TVC
3
CH SELECT
8
Transmit icon
Blinks to indicate the remote is transmitting
control signals.
CD-R
MULTI CONTROL
RCV
3
RECEIVER
SOURCE
1
2
04
D.ACCESS
T.EDIT/GUIDE
DIR SET
Indicates that the remote is in Direct
Setup mode so you can put it in DIRECT
FUNCTION (see pages 47–51).
RECEIVER CONTROL
TUNE
S ETU P
ST
ST
ENTER
TUNE
14
15
CHANNEL
BRAND
Indicates that the remote is in preset code
Search by Brand mode to find the preset
codes for your components by brand (see
page 49).
MENU
TV VOL
TV INPUT
12
MASTER VOLUME
16
TV
17
TV CONTROL
LEARN
Indicates that the remote is in Learning
mode and ready to learn signals from
other remote controls (see page 49).
3
LEARN
ERASE
SEARCH
Indicates that the remote is in Preset
Code Search mode to find the preset
codes for your components (see page 48).
SEARCH BY BRAND
ERASE
Indicates that the remote is in Erase mode
so that you can erase one or more learned
buttons. (see page 50).
4
1
SOURCE
Press to turn on/off other components connected to the receiver.
2
LCD Screen
This screen displays the mode the receiver is in,
commands sent, etc.
RESET
Indicates that the remote is in Reset mode
so that you can return it to default
settings (see page 50).
READ ID
Indicates that the remote is in Read ID
mode so that you can check the preset
codes (see page 51).
27
En
04
Controls and Displays
5
MULTI CONTROL buttons
Press to select control of other components
(see Controlling the Rest of Your System on
pages 47–51).
6
RCV
Switches the remote to controls the receiver
(used to select the features above the number
buttons. (ex. INPUT ATT, FL. DIMMER)). Also
use this button to set up surround sound
(pages 36, 42).
7
Number buttons/Receiver controls/
ENTER
Use the number buttons to directly select a
radio frequency (page 43) or the tracks on a CD,
DVD, etc.
DISPLAY/ DISC (ENTER)
The button’s use depends on the
component selected. It can be used to
switch the display between the station
preset name and the frequency for the
tuner, enter commands for TV or DTV, and
can also be used to select a disc in a multiCD player.
Receiver Controls
Press the RCV button first to access the
functions above the number buttons. The
display flashes when it isn’t possible to use
a function.
TEST TONE (page 42)
Sounds the test tone when setting up the
surround sound of the receiver.
INPUT ATT
Attenuates (lowers) the level of an analog
input signal to prevent distortion (when the
overload indicator lights).
FL DIMMER
Dims or brightens the display.
CH SELECT (page 42)
Selects a speaker when setting up the
surround sound of the receiver.
28
En
LEVEL +/– (page 42)
Adjusts the levels of the surround sound of
the receiver.
EFFECT +/– buttons (page 33)
Adds or subtracts the amount of effect
with different advanced listening modes
(except 5 or 6 Ch Stereo and Virtual SB).
8
Component/Tuner controls
The main buttons (3, 7, etc.) are used to
control a component after you have selected it
using the MULTI CONTROL buttons. The tuner/
DTV controls above these buttons can be
accessed after you have selected the corresponding MULTI CONTROL button (TUNER or
DVD (when connected to DTV)).
DTV INFO
Use to bring up information screens on a
digital TV.
MPX/RETURN (page 43)
Switches between stereo and mono
reception of FM broadcasts. If the signal is
weak then switching to mono will improve
the sound quality. Also acts as a stop
button for CDs, tapes, or DVDs.
D. ACCESS (page 43)
After pressing, you can access a radio
station directly using the number buttons.
T. EDIT/GUIDE (pages 44–45)
Press to memorize and name a station for
recall using the STATION +/– buttons or
the MULTI JOG/ INPUT SELECTOR dial. Also
displays the guides on a digital TV.
BAND (page 43)
Switches between the tuner AM and FM
bands.
CLASS (pages 44–45)
Switches between the three banks
(classes) of radio station presets.
DTV ON/OFF
Switches a digital TV on/off.
Controls and Displays
DTV MENU
Displays menus on a digital TV.
9
DVD controls (Press DVD first to access)
These controls will also function as DTV
controls, depending on the component you’ve
selected.
TOP MENU
Displays the disc ‘top’ menu of a DVD.
AUDIO
Changes the audio language or channel.
SUBTITLE
Displays/changes the subtitles included in
multilingual DVD-Video discs.
ANGLE
Switches camera angles on discs with
multi-angle scenes.
10 REMOTE SETUP (pages 47–51)
Press this button to set up the remote control to
control other components.
11
RECEIVER CONTROL buttons
STANDARD (pages 30, 32–33)
Press to switch between the various Dolby/
DTS modes
ADV. SURR. (pages 31, 33)
Use to switch between the various
surround modes.
STEREO (pages 30, 33)
Switches direct playback on or off. This
bypasses the tone controls and channel
levels for the most accurate reproduction
of a source.
INPUT SELECT
Use to select the input source.
04
MIDNIGHT/LOUDNESS (page 33)
Switches to Midnight or Loudness
listening.
MUTE
Mutes the sound (or restores the sound if
it has been muted).
12 TV control buttons
These buttons can only be used to control your
TV.
TV VOLUME +/–
Use to adjust the volume on your TV.
TV INPUT
Use select the TV function.
TV
Use to turn on/off the power of the TV.
13 RECEIVER
This switches between standby and on for this
receiver.
14 }]‘’ (TUNE/ST +/–) /ENTER
Use the arrow buttons when setting up your
surround sound system (see pages 36–41). Also
used to control DVD menus/options and for
deck 1 of a double cassette deck player. Use the
TUNE +/– buttons to find radio frequencies and
use ST +/– to find and name preset stations
(page 43–45).
15 CHANNEL +/–
Select radio station presets. Also skip tracks
backward or forward on CDs, DVDs, etc.
16 MASTER VOLUME +/–
Use to set the listening volume.
17 MENU button
Displays the disc menu of DVD-Video discs. It
also displays TV and DTV menus.
SIGNAL SELECT (pages 32, 35, 46)
Use to select an input signal.
29
En
05
Playing sources
Introduction to Sound Modes
There are three basic sound options: Stereo/
Direct, Standard or Advanced Surround.
Stereo/Direct
When you select STEREO or DIRECT, you will
hear the source through just the front left and
right speakers (and possibly your subwoofer
depending on your speaker settings). Dolby
Digital and DTS multichannel sources are
downmixed to stereo.
In STEREO, you’ll hear the audio with your
surround settings and you can still use the
Midnight, Loudness, and Tone control functions.
With DIRECT, you will bypass all effects and
surround settings so that the audio remains as
close to the source audio signal as possible.
the surround back speakers in your setup. For
more on this, refer to the table on the next page.
Choose one of the following to add depth to a 2
channel source:
Pro Logic
This mode gives 4.1 channel surround sound. It
is less sensitive to the quality of the source
material, so may be useful when Pro Logic II
Movie/ Music modes don’t give good results.
Pro Logic II Movie
This mode gives 5.1 channel surround sound. It
is suitable for movies, especially those recorded
in Dolby Surround. The channel separation and
movement of surround effects is comparable to
Dolby Digital 5.1.
Pro Logic II Music
If you switch on Midnight listening,
Loudness, or the Tone controls when
DIRECT is selected, the receiver automatically switches to STEREO.
Standard mode
The standard mode can be used to decode
Dolby Digital, DTS, or Dolby Surround sources.
The other surround sound options (next
column) can add multichannel sound to regular
stereo sources. If you play a Dolby Digital or
DTS source the receiver will change to that
mode automatically.
You can identify Dolby Digital software by the
marks. Most Dolby
1 or
Surround software is marked 3, but
unmarked software may also incorporate Dolby
Surround. Depending on the source, the 6.1
channel setting (page 38), and the sound mode
you have selected, you may not get sound from
30
En
This mode gives 5.1 channel surround sound
and is suitable for music. The surround effect is
more enveloping than Pro Logic II Movie.
Neo:6 Cinema
This mode gives 6.1 channel surround sound
and is suitable for movies. The Neo:6 Cinema
mode delivers good channel separation for
movie soundtracks.
Neo:6 Music
This mode gives 6.1 channel surround sound
and is suitable for music. The Neo:6 Music
mode plays the stereo source as is through the
front left/right speakers, and generates a
natural, ambient surround and center sound.
Playing sources
05
Advanced Surround modes
Virtual Surround Back (VIRTL SB)
These are designed to be used with
multichannel surround sound audio/video
sources (like DVDs and LDs). Most Advanced
Surround modes are designed to be used with
film soundtracks, but some modes are also
suited for music sources. Try different settings
with various soundtracks to see which you like.
The Virtual Surround Back effect simulates 7.1
surround channel listening (like Dolby Digital
Surround EX or DTS–EX), giving the impression
that there are two surround back speakers in
your system when listening to a 5.1 channel
source.
Expanded
Depending on the source, the 6.1 channel
setting (page 40), and the sound mode you
have selected, you may not get sound from
the surround back speakers in your setup.
For more on this, refer to the table below.
This mode is especially designed to give sound
depth to stereo sources, and lets you hear twochannel (stereo) signals as simulated
multichannel surround sound. Use with Dolby
Pro Logic for a stereo surround effect. You can
also use with Dolby Digital sources for a wider
stereo field than the Standard modes.
Movie
6-Channel Stereo
Simulates the relaxed environment of a movie
theater, and is suitable for watching movies.
This can be selected to give multichannel
sound to a stereo source, using all of the
speakers in your setup.
Music
Simulates the acoustic environment of a large
concert hall and is suitable for music or
musical sources.
6.1 ch.
setting
Standard
DTS-ES/Dolby Digital Surround EX encoded
multi-channel sources with 6.1 surround
Auto
√
√
√
√
Fix
√
√
√
√
Dolby Digital/DTS encoded multi-channel
sources with stereo surround
Auto
√
√
√
√
√
Dolby Digital/DTS encoded multi-channel
sources with mono surround, Stereo sources
Auto
Analog 2-channel (stereo) source
Auto
Type of source
Fix
Fix
Fix
Advanced
Virtual SB Expanded
Movie/Music
6 Ch.
Stereo
√
√
√
√
√
√
• The check mark (√) indicates when sound will be output from the surround back speaker(s).
• See the 6.1 channel setting on page 40 to select between AUTO or FIX.
31
En
05
Playing sources
Choosing the input signal
•
You may get digital noise when a LD
or CD player compatible with DTS is
playing an analog signal. To prevent noise,
make the proper digital connections (page
14) and set the signal input to DIGITAL.
You need to hook up a component to both
analog and digital inputs on the rear of the
receiver to select between input signals.
LEARN ERASE
DVD
•
Some DVD players don’t output DTS
signals. For more details, refer to the
instruction manual supplied with your DVD
player.
RECEIVER
SOURCE
SEARCH BY BRAND
TV
VCR
CD-R
MULTI CONTROL
RCV
TUN
CD
TVC
1
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
6
CH SELECT
LEVEL
8
7
9
+10
EFFECT
0
DISPLAY
DISC
ENTER
DTV INFO
MPX/RETURN
D.ACCESS
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
¡
4
¢
TOP MENU
REMOTE SETUP
INPUT SEL.
Listening to multichannel
playback
T.EDIT/GUIDE
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
RECEIVER
SOURCE
LEARN ERASE
SEARCH BY BRAND
RECEIVER CONTROL
TUNE
ST
S ETU P
DVD
TV
VCR
TUN
CD
RCV
TUNE
2
3
INPUT ATT
FL DIMMER
4
5
6
LEVEL
8
7
9
+10
MPX/RETURN
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
¡
4
¢
TOP MENU
INPUT SEL.
D.ACCESS
T.EDIT/GUIDE
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
RECEIVER CONTROL
TUNE
ST
S ETU P
ST
ENTER
DVD 7.1ch will only appear when DVD/LD is
selected using the remote or the MULTI JOG/
INPUT SELECTOR dial on the front panel.
En
DISPLAY
DISC
ENTER
DTV INFO
REMOTE SETUP
Each press switches between AUTO, DVD
7.1ch, ANALOG and DIGITAL. The default is
AUTO.
•
This receiver can only play back
Dolby Digital, PCM (32kHz, 44kHz, 48kHz,
and 96 kHz) and DTS digital signal
formats. With other digital signal formats,
set to ANALOG.
EFFECT
0
•
Press SIGNAL SEL (SIGNAL SELECT) to
select the input signal corresponding to the
source component.
When set to DIGITAL, 2 DIGITAL lights when
a Dolby Digital signal is input, and DTS lights
when a DTS signal is input.
TVC
1
TEST TONE
CH SELECT
32
CD-R
MULTI CONTROL
ST
ENTER
TUNE
1
Switch on the playback component.
2
Select the source you want to playback.
Use the MULTI CONTROL buttons on the
remote (or MULTI JOG/INPUT SELECTOR dial
on the front panel).
3
Press STANDARD.
If the source is Dolby Digital, DTS, or Dolby
Surround encoded, the proper decoding format
will automatically be selected and shows in the
display.
Playing sources
05
If you are listening to a two channel source,
each press changes the display as follows:
Pro Logic II Movie
Movie
Pro Logic
II Music
Pro Logic
Neo:6
Music
•
Press ADV.SURR. (ADVANCED SURROUND) repeatedly to cycle the sound
options.
Each press changes the display as follows:
Neo:6
Cinema
Refer to page 30 for more details about each
mode.
4
Start playback of the component you
selected in step 1.
Using Stereo/Direct
When you select STEREO or DIRECT, you will
hear the source through just the front left and
right speakers (and possibly your subwoofer
depending on your speaker settings). Dolby
Digital and DTS multichannel sources are
downmixed to stereo. See page 30 for more on
these modes.
•
Press STEREO (STEREO/DIRECT on the
front panel) repeatedly to switch between
the two options.
If you switch on Midnight listening,
Loudness, or the Tone controls when
DIRECT is selected, the receiver automatically switches to STEREO.
6-Stereo
Virtual SB
Expanded
Refer to page 31 for more details about each
surround effect.
The Advanced surround effects can be
adjusted in the range of 10 to 90 (the
default setting is 70) by pressing RCV then
pressing EFFECT +/– . The effect level can
be set for each Advanced surround mode.
The Standard mode cannot be changed.
Using Loudness and Midnight
listening
The Loudness listening feature can be used to
get good bass and treble from music sources at
low volume levels.
The Midnight listening feature allows you to
hear effective surround sound of movies at low
volume levels. The effect automatically adjusts
according to the volume at which you’re
listening.
•
Press MIDNIGHT/LOUDNESS.
Each press cycles through the effects as
follows:
Using Advanced Surround
When you select one of the Advanced surround
options, Dolby Pro Logic, Dolby Digital and DTS
decoding is done automatically corresponding
to the input signal. Use Advanced surround to
add effects to the surround sound.
Music
Midnight
Off
Loudness
33
En
05
Playing sources
Using the tone controls
Playing other sources
Depending on what you are listening to, you
may want to adjust the bass or treble using the
front panel tone control.
RECEIVER
SOURCE
LEARN ERASE
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
DVD
N∫m-¯,
SEARCH BY BRAND
TV
VCR
CD-R
MULTI CONTROL
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
ENTER
6
CH SELECT
LEVEL
8
7
MASTER VOLUME
9
+10
SPEAKERS
MONITOR
TONE
0
UP
DTV INFO
MULTI JOG
VIDEO INPUT
VIDEO
L
AUDIO
R
MPX/RETURN
DISPLAY
DISC
ENTER
D.ACCESS
T.EDIT/GUIDE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
S-VIDEO
EFFECT
QUICK SETUP
DOWN
TVC
1
INPUT
SELECTOR
MULTI JOG
TUN
CD
RCV
TOP MENU
REMOTE SETUP
INPUT SEL.
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
RECEIVER CONTROL
TUNE
ST
S ETU P
ST
ENTER
1
Press TONE to select the frequency you
want to adjust.
Each press switches between BASS and
TREBLE.
2
Use the MULTI JOG/INPUT SELECTOR
dial to change the amount of bass or treble
as necessary.
Wait about five seconds for your changes to be
input automatically.
TUNE
1
Turn on the power of the playback
component.
2
Turn on the power of the receiver.
3
Select the source you want to playback.
Use the MULTI CONTROL buttons on the
remote (or MULTI JOG/INPUT SELECTOR dial
on the front panel).
4
Start playback of the component you
selected in step 1.
Selecting the multichannel
analog inputs
If you have connected a decoder or a DVD
player with multichannel analog outputs to this
receiver (page 16), you must select the analog
multichannel inputs for surround sound
playback.
34
En
Playing sources
05
Using Re-Equalization
RECEIVER
SOURCE
LEARN ERASE
DVD
SEARCH BY BRAND
TV
VCR
CD-R
MULTI CONTROL
TUN
CD
RCV
TVC
1
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
6
CH SELECT
LEVEL
8
7
9
+10
EFFECT
0
DISPLAY
DISC
ENTER
DTV INFO
MPX/RETURN
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
¡
4
¢
TOP MENU
REMOTE SETUP
INPUT SEL.
D.ACCESS
T.EDIT/GUIDE
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
RECEIVER CONTROL
TUNE
ST
S ETU P
ST
ENTER
1
Press DVD or select it with the MULTI
JOG/INPUT SELECTOR dial (front panel).
2
Press SIGNAL SEL (SIGNAL SELECT)
repeatedly to select DVD 7.1ch.
To cancel playback from the multichannel
inputs, use the SIGNAL SEL (SIGNAL SELECT)
button to select a different input signal.
• When playback from the multichannel
inputs is selected, you can’t use the
SPEAKER, INPUT ATT, TONE, and
MIDNIGHT/LOUDNESS buttons, as well
as the Standard, Advanced Surround, and
Stereo/Direct sound modes.
Re-equalization compensates for the effect of
reproducing sounds in a smaller room that
have been originally processed for a large
movie theatre that can handle lots of high
frequencies. Both the front and the center
channels were originally mixed to give normal
sound behind a heavy projection screen, and
might sound unnaturally bright with a home
theater setup. Use the Re-equalization feature
to even out the sound if you feel that movie
soundtracks are sounding slightly harsh.
•
Press the Re-EQ button on the front
panel.
The receiver automatically switches to Standard
mode and Re-equalization is applied. Press ReEQ again to switch Re-equalization off.
• You can't use the NEO:6 Music and Pro
Logic II Music modes when Re-equalization
is on.
•
If STEREO or one of the Advanced
Surround modes is selected, Re-equalization is automatically cancelled. Selecting
speaker system B will also cancel Reequalization.
• Re-equalization is not applied to the
headphone mix.
• When playback from the multichannel
inputs is selected, only the volume and
channel levels can be set.
35
En
06
Setting up the receiver
Choosing your receiver setup
To ensure the best possible surround sound, be
sure to complete the following set up
operations. This is particularly important when
using Dolby surround. You only need to make
these settings once (unless you change the
placement of your current speaker system or
add new speakers, etc.). Refer to the following
pages for details on each of the settings.
RECEIVER
SOURCE
LEARN ERASE
DVD
TV
VCR
TUN
CD
TVC
1
2
3
INPUT ATT
FL DIMMER
4
5
6
CH SELECT
LEVEL
8
7
9
EFFECT
+10
0
MPX/RETURN
DISPLAY
DISC
ENTER
D.ACCESS
T.EDIT/GUIDE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
¡
4
¢
TOP MENU
REMOTE SETUP
INPUT SEL.
6.1 channel setting (page 38)
Set when 6.1 channel decoding is used.
Subwoofer setting (page 38)
Specify how the subwoofer is used.
Crossover frequency setting (page 38)
Determine which frequencies will be
sent to the subwoofer (or large speakers).
CD-R
TEST TONE
DTV INFO
Surround back speaker setting (page
37)
Specify your surround back speaker/
surround back subwoofer setup.
SEARCH BY BRAND
MULTI CONTROL
RCV
Speaker setting (page 37)
Specify the number and type of
speakers you have connected.
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
LFE attenuator setting (page 39)
Specify the peak level for the LFE
channel.
Front speaker distance setting (page 39)
Specify the distance from your listening
position to your front speakers.
RECEIVER CONTROL
TUNE
ST
S ETU P
ST
ENTER
TUNE
1
Press
RECEIVER to turn the power
on.
The STANDBY indicator goes out.
2
Press RCV.
3
Use } or ] to choose the option you
want to adjust.
It will be easiest to adjust each of the settings in
turn, following the order below (and on the
following pages). The current setting is shown
for each option as you cycle through the
display.
36
En
Center speaker distance setting (page
39)
Specifies the distance from your
listening position to your center speaker.
Surround speaker distance setting (page
39)
Specify the distance from your listening
position to your surround speakers.
Surround back speaker distance setting
(page 39)
Specifies the distance from your
listening position to your surround back
speakers.
Dynamic range control setting (page 40)
Compress the dynamic range of the
sound track.
Dual mono setting (page 40)
Isolate one channel when listening to
discs with dual mono encoding.
Setting up the receiver
Component video input setting (page
40)
Specify the components to be assigned
to the component video inputs (below).
• Component video 1 input setting
• Component video 2 input setting
Surround back channel input setting
(page 40)
Specify the number of surround back
inputs you have connected.
Digital input settings (page 41)
Specify the components to be assigned
to the video and digital inputs (below).
06
•
If the cone size (diameter) of the
speaker is larger than 5 inches, set the
speaker size to L.
• If you’re not using a subwoofer, we
recommend setting the front speakers to L.
•
Cycle through the available choices
using ’ or ‘ and choose a configuration
that matches your speaker setup.
One of the following configurations should
match your setup:
• Coaxial digital input 1 setting
FS-CS-SS
• Coaxial digital input 2 setting
• Optical digital input 1 setting
FL-C -SS
FS-CS-S
FL-C -SL
FS-C -SS
FL-CS-S
FL-CL-SL
FL-CS-SS
FL-CL-SS
FL-CS-SL
FL-CL-S
• Optical digital input 2 setting
4
Use ’ or ‘ to adjust the setting.
The setting is entered automatically.
5
Repeat steps 3 and 4 to set other
surround modes.
6
When you’re done, press ENTER to exit.
The setting display is automatically exited
after 20 seconds of inactivity.
Speaker setting
• Default setting: S (all speakers)
You must let the receiver know how many
speakers you have, and how big they are. The
size you choose (large or small) determines
how much bass is sent from the receiver to the
speakers.
In the display, F, C, and S refer to front, center,
and surround speakers respectively. Speaker
size is denoted as L for large speakers, S for
small speakers, and (asterisk) if no speaker is
connected.
Surround back speaker setting
• Default setting: S
You must let the receiver know if surround back
speaker(s) have been connected, and how big
they are. The size you choose (large or small)
determines how much bass is sent from the
receiver to the speakers. If you have connected
a surround back subwoofer, you should select
the surround back subwoofer setting (SB
SUBWF) from the options. Choose (asterisk) if
no speaker is connected.
•
Use ’ or ‘ to select SB L, SB S, SB or
SB SUBWF.
37
En
06
Setting up the receiver
6.1 channel setting
•
Default setting: 6.1 FIX
Crossover frequency setting
• Default setting: 100 Hz
You can have the receiver automatically switch
to Dolby Digital Surround EX or DTS-ES
decoding for 6.1 encoded sources (6.1 AUTO),
or you can choose to listen to other kinds of
sources (for example, 5.1 encoded material)
with 6.1 encoding (6.1 FIX). With 5.1 encoded
sources, a surround back channel will be
generated, but the material may sound better in
the 5.1 format for which it was originally
encoded.
Crossover frequency is the point where the
receiver divides the high and low sounds (the
frequencies) between the speakers. Since most
smaller speakers can’t handle deep bass tones,
you can send these sounds to the subwoofer (or
if you don’t have a subwoofer, the large (L)
speakers in your system) instead of the
speakers set to small (S) in your setup. Choose
the point at which you want the frequency
routed to the subwoofer (or L speakers).
•
Use ’ or ‘ to select 6.1 FIX or 6.1
AUTO.
We recommend setting this to 200 Hz if your S
speakers are smaller bookshelf-type speakers.
•
Use ’ or ‘ to specify the crossover
frequency for your small speakers (100 Hz,
150 Hz or 200 Hz).
• If you chose SB in Surround back
speaker setting (above), you can’t set the
6.1 channel setting and
shows in the
display.
• Refer to the table on page 31 to see
how the 6.1 channel setting affects sound
output from the surround back speakers.
Subwoofer setting
• Default setting: ON
You can choose whether the subwoofer is used
or not. Use the plus (PLS) setting for extra bass.
•
Use ’ or ‘ to select subwoofer ON, PLS
or OFF.
• If you chose the small front speaker
setting, SUBWF ON is automatically set
and locked.
• When you select the plus setting, you
will get the bass sounds from the
subwoofer even if the front speakers are
set to L.
38
En
100Hz
150Hz
200Hz
100 Hz
Sends bass frequencies below 100 Hz
to the subwoofer (or L speakers).
150 Hz
Sends bass frequencies below 150 Hz
to the subwoofer (or L speakers).
200 Hz
Sends bass frequencies below 200 Hz
to the subwoofer (or L speakers).
If all speakers (front, center, and surround)
are set to L, the crossover frequency can’t
be set because there are no S speakers
(
appears in the display).
Setting up the receiver
06
LFE attenuator setting
•
Default setting: 0 dB
Dolby Digital and DTS audio sources include
ultra-low bass tones. Set the LFE attenuator as
necessary to prevent the ultra-low bass tones
from distorting the sound from the speakers.
•
Use ’ or ‘ to set the attenuation level
(0 dB, 10 dB or
dB(∞)).
0 dB
10 dB
∞ (displays
When C is selected in the speaker setting,
the center speaker distance can’t be set.
Surround speaker distance setting
• Default setting: 10 ft.
Like the center speaker, you should set the
distance of the surround speakers accurately to
hear sounds coming from both front and
surround speakers at the same time.
)
When ∞ is selected (
appears in the
display), LFE is not available.
Front speaker distance setting
• Default setting: 10 ft.
Sets the distance from the front speakers to the
listening position.
•
Use ’ or ‘ to set the distance of the
front speakers from the main listening
position (within a 30 foot range).
Center speaker distance setting
• Default setting: 10 ft.
The center speaker is normally placed directly
in the front of the listening room and closer to
the listening position than the front speakers.
This means that the sound from the center
speaker will be heard before the front speakers.
To prevent this, set the center speaker distance
setting to delay the sound from the center
speaker so that the sound from the front and
center speakers will be heard at the same time.
•
Use ’ or ‘ to set the distance of the
center speaker from the main listening
position (within a 30 foot range).
•
Use ’ or ‘ to set the distance of the
surround speakers from the main listening
position (within a 30 foot range).
When S is selected in the speaker setting,
the surround speaker distance can’t be
set.
Surround back speaker distance
setting
• Default setting: 10 ft.
Like the center speaker, you should set the
distance of the surround speakers accurately to
hear sounds coming from both front and
surround speakers at the same time.
•
Use ’ or ‘ to set the distance of the
surround speakers from the main listening
position (within a 30 foot range).
When SB is selected in the surround
speaker setting, the surround back
speaker distance can’t be set.
39
En
06
Setting up the receiver
Dynamic range control setting
• Default setting: OFF
Dynamic range is the difference between the
loudest and softest sounds in any given signal.
With this setting, you can compress the
dynamic range, so that low level sounds can be
heard more easily (sounding relatively louder)
yet louder sounds won’t be too overbearing.
•
Press ’ or ‘ to set the dynamic range
control (OFF, MAX, or MID).
• When the volume level is increased, set
to OFF.
•
Use ’ or ‘ to cycle through the
possible dual mono settings.
L ch 1.R ch 2
ch2
ch1
Component video input settings
Here you tell the receiver what components you
have hooked up to the component video jacks
on the back of the receiver.
Component video 1:
• Default settings: DVD
• When listening at low volumes, set to
MAX for maximum dynamic range
compression.
1
Use ’ or ‘ to assign the component
video 1 input (DVD, TV, VCR or OFF).
• Dynamic range control is effective only
when a Dolby Digital signal is being played
back.
Component video 2:
Dual mono setting
• Default setting: TV
2
Use ’ or ‘ to assign the component
video 2 input (DVD, TV, VCR or OFF).
• Default setting: ch1
The dual mono setting can only be used when
listening to Dolby Digital discs with dual mono
encoding. These discs are not widely used, but
are sometimes used when it is necessary to
have one language on one channel and a
different language on the other. With this
setting you can choose which channel in the
dual mono setting you want to listen to.
You will hear the channel you have selected
(either ch1 or ch2) through your center speaker.
If you don’t have a center speaker, you will hear
the channel you have selected through both
front speakers. In the L ch 1. R ch 2 setting, the
left front speaker will play channel 1 and the
right front speaker will play channel 2.
40
En
Surround back channel input
setting
• Default setting: SB 2ch IN
You only have to make this setting if you are
using a separate component for decoding
DVDs, and the component has only one
surround back channel output. If this is the
case, select SB 1ch IN, otherwise leave it set to
SB 2ch IN.
•
Use ’ or ‘ to select SB 2ch IN or
SB 1ch IN.
Setting up the receiver
06
Coaxial digital input settings
Here you tell the receiver what components you
have hooked up to the coaxial DIGITAL IN jacks
1 and 2 on the back of the receiver.
Coaxial digital 1:
• Default settings: DVD/LD
1
Use ’ or ‘ to assign the coaxial digital
1 input (DVD, TV, CD, CD-R, VCR or OFF).
Coaxial digital 2:
• Default setting: CD
2
Use ’ or ‘ to assign the coaxial digital
2 input (DVD, TV, CD, CD-R, VCR or OFF).
After you assign a component to a digital jack,
whenever you select that component, (for
example, a DVD player) the receiver
automatically changes to the digital input
setting and DIGITAL shows in the display.
Optical digital input settings
Here you tell the receiver what components you
have hooked up to the optical DIGITAL IN
jack(s) on the back of the receiver.
Optical digital 1:
• Default settings: TV/SAT
1
Use ’ or ‘ to assign the optical digital
1 input (DVD, TV, CD, CD-R, VCR or OFF).
Optical digital 2
• Default setting: CDR/TAPE/MD
2
Use ’ or ‘ to assign the optical digital
2 input (DVD, TV, CD, CD-R, VCR or OFF).
After you assign a component to a digital jack,
whenever you select that component, (for
example, a DVD player) the receiver
automatically changes to the digital input
setting and DIGITAL shows in the display.
41
En
06
Setting up the receiver
Setting the relative volume level
of each channel
• Default setting: 0db
For best surround sound playback, you should
set the relative channel levels from the main
listening position. You can set separate levels
for each surround mode.
1
Press RCV.
2
Press STANDARD.
The speaker volume can be adjusted
without outputting the test tone by
pressing CH SELECT and then using
LEVEL +/–.
3
Press TEST TONE to output the test
tone.
The test tone is output in the following order
(depending on the speaker setting):
FL
C
RECEIVER
SOURCE
FR
LEARN ERASE
DVD
SEARCH BY BRAND
TV
VCR
TUN
CD
1
2
TEST TONE
INPUT ATT
4
5
3
6
LEVEL
8
7
9
+10
SW
SL
SB
TVC
FL DIMMER
CH SELECT
SR
CD-R
MULTI CONTROL
RCV
EFFECT
0
DTV INFO
MPX/RETURN
DISPLAY
DISC
ENTER
D.ACCESS
T.EDIT/GUIDE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
TOP MENU
REMOTE SETUP
INPUT SEL.
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
RECEIVER CONTROL
TUNE
S ETU P
ST
If you don’t hear a test tone from one of
your speakers, please refer to Speaker
setting on page 37 to make sure you have
correctly specified your speaker setup.
TUNE
CHANNEL
MENU
TV VOL
4
Press MASTER VOLUME +/– to adjust
the volume to an appropriate level.
ST
ENTER
TV INPUT
MASTER VOLUME
TV
TV CONTROL
5
Use LEVEL +/- to adjust the speaker
levels in turn.
You should hear the test tone at the same
volume from each speaker when seated in the
main listening position. The channel level range
is ± 10 dB.
6
When you’re done, press TEST TONE to
turn off the test tone.
• Test tone is only output in Standard
modes.
• Since the subwoofer transmits an ultralow frequency its sound may seem quieter
than it actually is.
42
En
Using the tuner
07
Manual tuning
To change the frequency one step at a
time, press TUNE +/–.
Listening to the radio
The following steps show you how to tune in to
FM and AM radio broadcasts using the
automatic (search) and manual (step) tuning
functions. If you already know the frequency of
the station you want, see Tuning directly to a
station below. Once you are tuned to a station
you can memorize the frequency for recall
later—see Saving station presets on the next
page for more on how to do this.
RECEIVER
SOURCE
LEARN ERASE
DVD
SEARCH BY BRAND
TV
VCR
CD-R
MULTI CONTROL
TUN
CD
RCV
1
2
TEST TONE
INPUT ATT
4
5
TVC
FL DIMMER
6
8
7
9
EFFECT
0
MPX/RETURN
DISPLAY
DISC
T.EDIT/GUIDE
¶
7
3
BAND
CLASS
DTV ON/OFF
DTV MENU
1
¡
4
¢
INPUT SEL.
Tuning directly to a station
ENTER
D.ACCESS
8
TOP MENU
If the TUNED or STEREO indicators don't light
when tuning to an FM station because the
signal is weak, press the MPX(/RETURN)
button to switch the receiver into mono
reception mode. This should improve the sound
quality and allow you to enjoy the broadcast.
LEVEL
+10
REMOTE SETUP
Improving FM stereo sound
3
CH SELECT
DTV INFO
High speed tuning
Press and hold TUNE +/– for high
speed tuning. Release the button at the
frequency you want.
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
RECEIVER CONTROL
Sometimes, you'll already know the frequency of
the station you want to listen to. In this case,
you can simply enter the frequency directly
using the number buttons on the remote
control.
TUNE
ST
S ETU P
ST
ENTER
TUNE
1
Press the TUN button on the remote
control to select the tuner.
You can also use the MULTI JOG/INPUT
SELECTOR dial on the front panel.
2
Use the BAND button to change the
band (FM or AM), if necessary.
Each press switches the band between FM and
AM.
3
Tune to a station.
There are three ways to do this:
Automatic tuning
To search for stations in the currently
selected band, press and hold TUNE +/–
for about a second. The receiver will start
searching for the next station, stopping
when it has found one. Repeat to search
for other stations.
1
Press the TUN button on the remote
control to select the tuner.
You can also use the MULTI JOG/INPUT
SELECTOR dial on the front panel.
2
Use the BAND button to change the
band (FM or AM), if necessary.
Each press switches the band between FM and
AM.
3
Press D.ACCESS (Direct Access).
4
Use the number buttons to enter the
frequency of the radio station.
For example, to tune to 106.00 (FM), press 1, 0,
6, 0, 0.
STEREO
FM
TUNED
SP A
106.10
If you make a mistake halfway through, press
D.ACCESS twice to cancel the frequency and
start over.
43
En
07
Using the tuner
Saving station presets
If you often listen to a particular radio station,
it's convenient to have the receiver store the
frequency for easy recall whenever you want to
listen to that station. This saves the effort of
manually tuning in each time. This unit can
memorize up to 30 stations, stored in three
banks, or classes, (A, B and C) of 10 stations
each. When saving an FM frequency, the MPX
setting (see previous page) is also stored. Use
the front panel controls to store station presets.
LEARN ERASE
DVD
TV
VCR
CD-R
TUN
CD
TVC
1
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
6
CH SELECT
LEVEL
8
7
9
+10
EFFECT
0
DTV INFO
MPX/RETURN
DISPLAY
DISC
ENTER
D.ACCESS
T.EDIT/GUIDE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
N∫m-¯,
REMOTE SETUP
INPUT SEL.
INPUT
SELECTOR
MULTI JOG
SEARCH BY BRAND
MULTI CONTROL
RCV
TOP MENU
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
RECEIVER
SOURCE
RECEIVER CONTROL
TUNE
ENTER
ST
S ETU P
ST
ENTER
MASTER VOLUME
SIGNAL
SELECT
MIDNIGHT/
LOUDNESS
MONITOR
SPEAKERS
TONE
QUICK SETUP
TUNE
UP
DOWN
MULTI JOG
VIDEO INPUT
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
R
1
Tune to a station you want to memorize.
See Listening to the radio (previous page) for
more on this.
STATION
TUNING
STANDARD
ADVANCED
SURROUND
STEREO/
DIRECT
SIGNAL
SELECT
MIDNIGHT/
LOUDNESS
SPEAKERS
MONITOR
TONE
QUICK SETUP
MULTI JOG
LISTENING MODE
VIDEO INPUT
TUNER EDIT
CLASS
BAND
MPX
INPUT ATT
FL DIMMER
MULTI JOG
DIGITAL IN
S-VIDEO
VIDEO
L
AUDIO
R
2
Press T.EDIT (TUNER EDIT).
The display shows ST. MEMORY, then a
blinking memory class.
STEREO
A-
TUNED
SP A
99.50
3
Press CLASS to select one of the three
classes then press ST +/– (STATION +/–) or
the } and ] keys to select the station
preset you want.
You can also use the MULTI JOG/INPUT
SELECTOR dial (front panel) to select a station
preset.
4
Press ENTER.
After pressing ENTER, the preset class and
number stop blinking and the receiver stores
the station.
44
En
Using the tuner
07
Naming station presets
Listening to station presets
For easier identification, you can name your
station presets.
If you haven’t already stored some station
presets, see the previous page to do so.
1
Choose the station preset you want to
name.
See Listening to station presets (this page) for
how to do this.
1
Press TUN (remote) or use the MULTI
JOG/INPUT SELECTOR dial on the front
panel to select the tuner.
2
Press T.EDIT (TUNER EDIT).
The display shows ST. NAME, then a blinking
cursor at the first character position.
2
Press CLASS to select the class in which
the station is stored.
Press repeatedly to cycle through classes A, B
and C.
3
Input the name you want.
Names can be up to four characters long.
3
Press ST +/– (STATION +/–) to select the
station preset you want.
•
Use the MULTI JOG/INPUT SELECTOR
dial or ST +/– buttons (front panel) the }
and ] buttons (remote) to select
characters.
•
Press ENTER to confirm a character.
If no character is input, a space is input.
•
If the receiver is left disconnected
from the AC power outlet for an extended
period, the station memories will be lost
and will have to be reprogrammed.
•
The name is stored when ENTER is
pressed after choosing the fourth
character.
To erase a station name, simply repeat
steps 1-3 and input four spaces instead of
a name.
Once you have named a station preset, you
can press DISPLAY when listening to a
station to switch the display between the
name and the frequency.
45
En
08
Making Recordings
Making an audio or a video
recording
4
Prepare the recorder.
Insert a blank tape, MD, video etc. into the
recording device and set the recording levels.
You can make an audio or a video recording
from the built-in tuner, or from an audio or video
source connected to the receiver (such as a CD
player or TV).
Refer to the instructions that came with the
recorder if you are unsure how to do this. Most
video recorders set the audio recording level
automatically—check the component’s
instruction manual if you’re unsure.
Keep in mind you can’t make a digital recording
from an analog source or vice-versa, so make
sure the components you are recording to/from
are hooked up in the same way (see pages 13–
19 for more on connections).
5
Start recording, then start playback of
the source component.
If you want to record a video source, you also
need use the same type of connection for the
source as for the recorder. For example, you
can’t record a component hooked up to S-video
jacks with a recorder hooked up to the component video outputs (see page 17 for more on
video connections).
RECEIVER
SOURCE
LEARN ERASE
DVD
SEARCH BY BRAND
TV
VCR
CD-R
MULTI CONTROL
TUN
CD
RCV
1
2
TEST TONE
INPUT ATT
4
5
TVC
3
FL DIMMER
6
CH SELECT
LEVEL
8
7
9
+10
EFFECT
0
DTV INFO
The receiver's volume, balance, tone (bass,
treble, loudness), and surround effects
have no effect on the recorded signal.
2
Select the input signal (if necessary).
Press SIGNAL SEL (SIGNAL SELECT) to select
the input signal corresponding to the source
component (see page 32 for more on this).
3
Prepare the source you want to record.
Tune to the radio station, load the CD, video,
DVD etc.
DISPLAY
DISC
D.ACCESS
T.EDIT/GUIDE
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
TOP MENU
REMOTE SETUP
INPUT SEL.
1
Select the source you want to record.
Use the MULTI CONTROL buttons on the
remote (or MULTI JOG/INPUT SELECTOR dial
on the front panel).
MPX/RETURN
ENTER
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
RECEIVER CONTROL
TUNE
ST
S ETU P
ST
ENTER
TUNE
Monitoring your recording
You can listen to (monitor) the recording as it's
being made using the MONITOR button on the
front panel (a cassette deck would have to have
a record monitor function).
•
Press the MONITOR button to switch
between the recorded signal and the
original source signal.
46
En
Controlling the rest of your system
Setting the remote to control
other components
09
Selecting preset codes directly
DVD
There are several ways to set your remote to
control the other components in your system.
The easiest way to do this is to assign the
component’s manufacturer preset code (listed
on page 55) to one of the MULTI CONTROL
buttons on the remote control.
Button Controllable Components
DVD:
TV:
VCR:
CD:
CD-R:
TVC:
TUN:
DVD or LD player
TV or Satellite tuner
VCR or Digital Video Recorder
CD player
CD Recorder, Tape deck
or MD player
TV or Cable TV tuner
FM/AM tuner
You can do this directly, or by searching
through different preset codes until you find
the right one. If you can’t find a preset code
that matches the component you want to
control, you can still teach the remote
individual commands from another remote
control (page 49–50).
You can cancel or exit any of the steps by
pressing and holding MUTE for three seconds.
VCR
CD-R
TUN
CD
TVC
1
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
6
CH SELECT
LEVEL
8
7
9
+10
EFFECT
0
DISPLAY
DISC
ENTER
DTV INFO
MPX/RETURN
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
TOP MENU
REMOTE SETUP
The buttons can be set to control the following
components:
TV
MULTI CONTROL
RCV
INPUT SEL.
D.ACCESS
T.EDIT/GUIDE
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
RECEIVER CONTROL
1 Press and hold REMOTE SETUP for
three seconds.
The LCD display shows SETUP.
2 Press the MULTI CONTROL button for
the component you want to control.
3 Use } and ] to select DIR SET then
press REMOTE SETUP.
The LCD on the remote displays the
component you want to control.
4 Use the number buttons to enter the 4
digit preset code (see pages 55–66)
The LCD display shows the code as you
enter it. If you make a mistake press the }
button to go back one digit. The display
shows OK once you have entered a valid
code. If it’s an invalid code or an error has
occurred, ERROR shows in the display.
If you get an error message, check the
preset code list and try again. If you can’t
find or properly enter a preset code, you can
still teach the remote individual commands
from another remote control (page 49).
• If you assign a preset code for the TUNER
button, you won’t be able to control the builtin tuner of this receiver using the remote.
Reset the remote to the built-in tuner by
entering the preset code 7008.
5 Repeat steps 1 through 4 for the other
components you want to control.
47
En
09
Controlling the rest of your system
Setting Up Using Full Library
Search
An alternative method of setting up the remote
with preset codes is to use the Library Search
feature. The remote transmits batches of 10
codes; when you see the component you want
to control respond (by turning on or off) you
just scan through those last 10 codes until you
find the correct one.
RECEIVER
SOURCE
LEARN ERASE
DVD
SEARCH BY BRAND
TV
VCR
TUN
CD
TVC
1
2
3
TEST TONE
INPUT ATT
FL DIMMER
4
5
6
CH SELECT
LEVEL
8
7
9
+10
EFFECT
0
DISPLAY
DISC
ENTER
DTV INFO
MPX/RETURN
¶
7
3
8
BAND
CLASS
DTV ON/OFF
DTV MENU
1
TOP MENU
REMOTE SETUP
INPUT SEL.
D.ACCESS
4 Use the } and ] buttons to select the
SEARCH.
The LCD display shows SEARCH.
5 Press and hold REMOTE SETUP for
three seconds.
A batch of 10 codes is transmitted and the
transmit icon blinks during transmission.
If you see the component respond, by
stopping (for playback components only) or
switching off, go on to the step 6, otherwise
press and hold the REMOTE SETUP button
for three seconds.
Cancelling this step can only be done after
the 10 codes are transmitted.
CD-R
MULTI CONTROL
RCV
3 Press the MULTI CONTROL button for
the component you want to control.
T.EDIT/GUIDE
¡
4
AUDIO
SUB TITLE
ANGLE
STANDARD
ADV.SURR.
STEREO
SIGNAL SEL
MIDNIGHT/
LOUDNESS
MUTE
¢
RECEIVER CONTROL
6 Switch the component back on or
restart playback.
7 Use ’ and ‘ buttons to scan step-bystep through the last 10 codes
transmitted to identify the correct code.
Stop when you see the component stop or
switch off. The LCD display shows the I.D.
TUNE
S ETU P
ST
ST
ENTER
You can also verify you have the correct
code by pressing PLAY, STOP., VOL +/–, etc.
TUNE
CHANNEL
MENU
TV VOL
TV INPUT
MASTER VOLUME
TV
8 Press and hold ENTER for three
seconds to save the preset code.
The LCD display shows OK.
TV CONTROL
The remote control automatically returns to
normal usage.
1 Switch on the component you want to
control.
If the component is some kind of player (CD
player, VCR, etc.), then start it playing.
2 Press and hold REMOTE SETUP for
three seconds.
The LCD display shows SETUP.
48
En
• Unless otherwise stated, you can cancel or
exit any of the steps by pressing and holding
MUTE for three seconds.
• The remote control will return to its previous
mode after 30 seconds of inactivity.
Controlling the rest of your system
09
Searching for preset codes using
brand names
Programming signals from
other remote controls
Another way of assigning preset codes is to
use the Brand Search feature.
If the preset code for your component is not
available, or the available preset codes do not
operate correctly, you can program signals from
the remote control of another component. This
can also be used to program additional
operations (buttons not covered in the presets)
after assigning a preset code.
1 Switch on the component you want to
control.
If the component is some kind of player (CD
player, VCR, etc.), then start it playing.
2 Press and hold REMOTE SETUP for
three seconds to enter the setup mode.
The LCD display shows SETUP.
3 Press the MULTI CONTROL button for
the component you want to control.
4 Use the } and ] buttons to select
BRAND then press REMOTE SETUP.
The brand names are displayed in alphabetical order. The display starts by showing the
letter A.
5 Use ’ and ‘ to select the first letter of
the brand of your component then
press ENTER.
The LCD will show the brands that start
from the letter you have selected.
If you make a mistake here, press } to go
back to the previous step.
6 Use ’ and ‘ to select the brand of your
component then press ENTER.
The LCD shows the component type and
codes relating to the brand.
7 Use ’ and ‘ to select your component
type (if you see the component respond) then press and hold ENTER for
three seconds to save the preset code.
The LCD display shows OK.
1 Press REMOTE SETUP and hold for
three seconds.
The LCD display shows SETUP.
2 Press the MULTI CONTROL button for
the component you want to control.
3 Prepare the remote to learn the remote
control signal from the component.
Use } and ] to select LEARN and then
press REMOTE SETUP.
The LCD display shows PRES KEY. The learn
icon indicates the remote is ready to accept
a signal.
To exit or cancel press and hold the SETUP
key for three seconds.
4 Point the two remote controls towards
each other about 1-2 inches apart then
press the button that will be doing the
learning on this receiver’s remote
control (for example 3, 7, etc.).
The LCD display flashes PRES KEY.
1-2 inches
5 Press the corresponding button on the
other remote control that is sending
(teaching) the signal to this receiver’s
remote control (for example 3, 7, etc.).
49
En
09
Controlling the rest of your system
The LCD display will show OK if the
operation has been learned.
If for some reasons the operation hasn’t
been learned the LCD will display ERROR for
three seconds and then display PRES KEY
again. If this happens, keep pressing the
(teaching) button as you vary the distance
between the two remotes, until the LCD
display shows OK.
To program additional operations for the
current component repeat steps 4 and 5.
To program operations for another component exit and repeat steps 1 through 5.
6 Press and hold the REMOTE SETUP
button for three seconds to store the
operation(s).
Erasing one of the remote
control button settings
This erases one of the buttons you have
programmed and restores the button to the
factory default.
1 Press REMOTE SETUP and hold for
three seconds.
The LCD display shows SETUP.
2 Press the MULTI CONTROL button
relating to the button setting to be
erased.
3 Prepare the remote to erase the button
setting.
Use } and ] to select ERASE and
then press REMOTE SETUP.
The LCD display flashes PRES KEY.
• Some commands from other remote controls
cannot be learned, but in most cases the
remotes just need to be moved closer together
or farther apart.
• Certain buttons represent operations that
cannot be learned from other remote controls.
These include: MULTI CONTROL, RECEIVER ,
REMOTE SETUP, RECEIVER CONTROL and
MASTER VOLUME.
• TV CONTROL buttons (TV , TV VOL +/-, and
TV INPUT) can only be learned after selecting
TV or TVC.
4 Press and hold the button to be erased
for three seconds.
The LCD display shows OK to confirm the
button has been erased or NO CODE if an
error has occurred.
5 Repeat step 4 to erase other buttons.
6 Press and hold the REMOTE SETUP
button for two seconds to exit.
Clearing all the remote
control settings
You can clear all presets and restore the factory
default settings.
1 Press REMOTE SETUP and hold for
three seconds.
The LCD display shows SETUP.
2 Press any MULTI CONTROL button.
50
En
3 Use } and ] to select RESET then
press REMOTE SETUP.
The LCD display shows OK.
Controlling the rest of your system
Direct function
• Default setting: ON
You can use the direct function feature to
control one component using the remote
control while at the same time, using your
receiver to playback a different component.
This could let you, for example, use the remote
control to set up and listen to a CD on the
receiver and then use the remote control to
rewind a tape in your VCR while you continue
to listen to your CD player.
When direct function is on, any component you
select (using the MULTI CONTROL buttons )
will be selected by both the receiver and the
remote control. When you turn direct function
off, you can operate the remote control without
affecting the receiver.
09
Confirming preset codes
Use this feature to check which preset code is
assigned to a MULTI CONTROL button.
1 Press REMOTE SETUP and hold for
three seconds.
The LCD display shows SETUP.
2 Press the MULTI CONTROL button of
the component for which you want to
check the preset code.
3 Use } and ] to select READ ID and
then press REMOTE SETUP.
The preset code appears in the display for
two seconds.
1 Press REMOTE SETUP and hold for
three seconds.
The LCD display shows SETUP.
2 Press the MULTI CONTROL button for
the component you want to control.
3 Use } and ] to select DIR SET then
press REMOTE SETUP.
The LCD on the remote displays the
component you want to control.
4 Use the number buttons to enter either
9990 (direct on) or 9995 (direct off).
The LCD will display OK to show the four
digit code has been accepted.
You can’t use direct function for TV INPUT.
51
En
09
Controlling the rest of your system
Controls for TVs
This remote control can control components after entering the proper codes or teaching the
receiver the commands (see pages 55–66). Use the MULTI CONTROL buttons to select the
component.
Button (s)
TV
52
En
Function
Components
Switches the DTV on or off.
DTV
Switches the TV or CATV between standby and on.
Cable TV/Satellite TV/TV
TV INPUT
Switches the TV input. (Not possible with all models.)
TV
CHANNEL
+/–
Selects channels.
Cable TV/Satellite TV/TV/
DTV
TV VOL
+/–
Adjust the TV volume.
Cable TV/Satellite TV/TV/
DTV
SOURCE
Press to switch the component assigned to the TVC
button on or off.
DTV
4
Switches DTV on or off.
DTV
¢
Press to display the DTV menu.
DTV
8
Use as the GUIDE button for navigating
DTV
¶
Press to get information on DTV programs.
DTV
TOP MENU Use to choose the BLUE commands on a DTV menu.
DTV
AUDIO
Use to choose the GREEN commands on a DTV menu.
DTV
SUB TITLE
Use to choose the RED commands on a DTV menu.
DTV
ANGLE
Use to choose the YELLOW commands on a DTV menu.
DTV
¡
Selects between screen formats for widescreen TVs.
TV
1
Use to clear a TV channel selected using the number
buttons.
Cable TV/TV
3
Use to switch DTV audio tracks
DTV
7
Use to select closed captioning with DTV.
DTV
Number
Buttons
Use to select a specific TV channel.
Cable TV/Satellite TV/TV/
DTV
+10 button Use to add a decimal point when selecting a specific TV
channel.
DTV
ENTER/
DISPLAY/
DISC
Cable TV/Satellite TV/TV
Use to enter a channel.
Controlling the rest of your system
Button (s)
MENU
Function
Components
Select different menus from the DTV functions.
DTV
Select the menu screen.
Cable TV/Satellite TV/TV
}]’‘ & Select or adjust and navigate items on the menu screen.
ENTER
ENTER brings up the DTV menus.
Press to select or adjust and navigate items on the menu
screen.
EFFECT
+/–
09
DTV
Cable TV/Satellite TV/TV/
DTV
For TV and cable TV use this button to immediately enter Cable TV/Satellite TV/TV/
a new channel (CHANNEL ENTER function). For satellite
DTV
TV use this button to exit the menu screen.
The four TV CONTROL buttons on the remote control are dedicated to control the TV assigned
to the TVC button. Thus if you only have one TV to hook up to this system assign it to the TVC
MULTI CONTROL button. If you have two TVs, assign the main TV to the TVC button.
Controls for other components
This remote control can control these components after entering the proper codes or teaching the
receiver the commands (see pages 55–66). Use the MULTI CONTROL buttons to select the
component.
Button (s)
Function
Components
SOURCE
Press to switch the component between standby and on. CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
4
Press to return to the start of the current track.
Repeated presses skips to the start of previous tracks.
CD/MD/CD-R/DVD/LD player
Go back channels (channel –).
VCR/DVR
Play the reverse side of the tape on a reversible deck.
Cassette deck
Press to advance to the start of the next track.
Repeated presses skips to the start of following tracks.
CD/MD/CD-R/LD player
Go forward channels (channel +).
VCR
¢
Play the forward side of the tape on a reversible deck.
Cassette deck
8
Pause playback or recording.
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
3
Start playback.
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
53
En
09
Controlling the rest of your system
Button (s)
54
En
Function
Components
¡
Hold down for fast forward playback.
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
1
Hold down for fast reverse playback.
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
7
Stops playback (on some models, pressing this when the
disc is already stopped will cause the disc tray to open).
CD/MD/CD-R/VCR/DVD/LD/
DVR player/Cassette deck
¶
Starts recording. To prevent accidental recording, this
button must be pressed twice to take effect (the second
press must be within 10 seconds of the first).
VCR/DVR player
Number
buttons
Directly access tracks on a program source.
CD/MD/CD-R/VCR/LD player
Use the number buttons to navigate the on-screen
display.
DVD/DVR player
+10 button Selects tracks higher than 10. (For example, press +10
then 3 to select track 13.)
CD/MD/CD-R/VCR/LD player
ENTER
Multiple CD player
Chooses the disc.
(DISPLAY/ Ejects the disc.
MD player
DISC)
Use as the ENTER button.
VCR
Displays the setup screen for DVD/DVR players.
DVD/DVR player
Changes sides of the LD.
LD player
Use as the SET UP button.
DVD/DVR player
MENU
Displays menus concerning the current DVD or DVR you
are using.
DVD/DVR player
’
Pauses the tape.
CD-R/Cassette deck
‘
Stops the tape.
CD-R/Cassette deck
ENTER
Starts playback.
CD-R/Cassette deck
}/]
Fast rewinds/fast forwards the tape.
CD-R/Cassette deck
}]’‘ & Navigates DVD menu/options.
ENTER
DVD/DVR Player
CHANNEL Selects channels.
VCR/DVD/DVR Player
+/–
CD/MD/CD-R/Cassette deck
Selects tracks.
TOP MENU Displays the disc ‘top’ menu of a DVD.
DVD/DVR Player
AUDIO
Changes the audio language or channel.
DVD/DVR Player
SUBTITLE
Displays/changes the subtitles on multilingual DVDs.
DVD/DVR Player
ANGLE
Switches camera angles on discs with multi-angle scenes. DVD/DVR Player
Controlling the rest of your system
09
Preset Code List
You can only set these codes for the buttons that assigned to the respective components. So, for
example, the TV codes can only be set to the TV or TVC button.
TV
Manufacturer
PHILIPS
SONY
PANASONIC
TOSHIBA
TELEFUNKEN
SHARP
SAMSUNG
FERGUSON
MITSUBISHI
GOLDSTAR
BLAUPUNKT
RADIOLA
JVC
DAEWOO
ORION
SIEMENS
ADMIRAL
ADYSON
AIKO
AKAI
AKURA
ACURA
ALARON
ALBA
ALLORGAN
ANAM
ANAM NATIONAL
AMBASSADOR
AMERICA ACTION
TV
TVC
Code
1008, 1017, 1020, 1025, 1104,
1115
1001, 1007, 1016
1023, 1054, 1055, 1075, 1076,
1082, 1087, 1121, 1124
1015, 1016, 1027, 1031, 1050,
1051, 1085
1005, 1026, 1034, 1038, 1042,
1046, 1075, 1097
1016, 1019, 1041, 1056, 1124
1006, 1011, 1013, 1017, 1026,
1027, 1039, 1062, 1079, 1089,
1092, 1102
1005, 1017, 1033, 1046, 1065,
1084, 1091
1011, 1016, 1041, 1045, 1049,
1062, 1114
1002, 1011, 1013, 1017, 1019,
1026, 1046, 1062, 1079, 1092
1066, 1068, 1071, 1075, 1115
1008, 1017
1016, 1024, 1030, 1053, 1065,
1067, 1103, 1122
1006, 1011, 1017, 1019, 1028,
1040, 1050, 1104, 1110, 1118,
1119
1017, 1063, 1083, 1095, 1098,
1099, 1112
1017, 1052, 1066, 1068, 1071,
1075, 1115
1041, 1055, 1075, 1112
1014, 1079
1040
1013, 1074
1080, 1089
1006
1063, 1078
1006, 1016, 1017, 1080, 1103
1095
1004, 1006, 1029, 1054, 1064,
1087, 1108
1054, 1087, 1108
1061
1064
AMPLIVISION
AMPRO
AMSTRAD
ANITECH
AOC
ARCAM
ASBERG
ASUKA
ATLANTIC
AUDIOSONIC
AUDIOVOX
AUTOVOX
BANG & OLUFSEN
BASIC LINE
BAYSONIC
BAUR
BEKO
BELCOR
BELL & HOWELL
BEON
BINATONE
BLUE SKY
BLUE STAR
BONDSTEC
BOOTS
BPL
BSR
BRADFORD
BRANDT
BRITANNIA
BROCKWOOD
BROKSONIC
BTC
BUSH
CANDLE
CARNIVALE
CARREFOUR
CARVER
CASCADE
CATHAY
CENTURY
CENTURION
CELEBRITY
CCE
CGE
CIMLINE
1079
1126
1006, 1017, 1103, 1105
1006, 1029, 1036
1011, 1013
1078, 1079
1036
1080
1073
1017, 1046
1040, 1064, 1110 , 1118
1036, 1073
1116
1006, 1080
1064
1007, 1017, 1114, 1115
1102
1011
1009, 1050
1017
1079
1080
1090
1086
1079
1090
1095
1064
1046, 1069, 1070, 1072
1078
1011
1083, 1112
1080
1006, 1016, 1017, 1080, 1090,
1095, 1103, 1104
1013, 1026
1013
1016
1025, 1058
1006
1017
1075
1017
1001
1017
1034, 1036, 1038, 1086, 1097
1006
55
En
09
Controlling the rest of your system
CINERAL
1040, 1110
CITIZEN
1013, 1019, 1026, 1027, 1040
CLARIVOX
1017
CLATRONIC
1036, 1086, 1102
CME
1007, 1015, 1114
CONCERTO
1026
CONDOR
1098, 1102
CONTEC
1006, 1016, 1064, 1078
CONTINENTAL EDISON 1069, 1070, 1072
CRAIG
1054
CROSLEY
1025, 1034, 1036, 1038, 1075
CROWN
1006, 1017, 1019, 1036, 1064,
1102, 1106
CRYSTAL
1109
CS ELECTRONICS 1078
CTC
1086
CURTIS MATHES
1009, 1013, 1019, 1022, 1023,
1025, 1026, 1027, 1041, 1047,
1050, 1057, 1110, 1113, 1129,
1131
CYBERTRON
1080
CXC
1064
DAINICHI
1077, 1080
DANSAI
1017
DAYTRON
1006, 1011
DECCA
1017, 1032
DE GRAAF
1074
DENON
1047
DIXI
1006, 1017
DUAL TEC
1079
DUMONT
1010, 1011, 1031
DWIN
1125, 1127
ECE
1017
ELBE
1088
ELECTROBAND
1001
ELIN
1017
ELITE
1080, 1098
ELTA
1006
EMERSON
1011, 1018, 1019, 1050, 1061,
1062, 1063, 1064, 1075, 1083,
1090, 1112, 1118, 1119
ENVISION
1013
ERRES
1008, 1017
ETRON
1006, 1120
EXPERT
1073
FIDELITY
1078
FINLANDIA
1074
FINLUX
1017, 1031, 1032 , 1044
FISHER
1050, 1074, 1079, 1096, 1102
FLINT
1111
FORMENTI
1017, 1075, 1098
FORTRESS
1041
56
En
FRONTECH
FUJITSU
FUNAI
1055, 1086, 1089, 1109
1032, 1063, 1073
1059, 1063, 1064, 1089, 1095,
1096
FUTURETECH
1064
GE
1012, 1022, 1023, 1041, 1062,
1090, 1110, 1129, 1131
GEC
1017, 1020, 1032, 1072, 1079
GELOSO
1006, 1075
GENEXXA
1055, 1080
GIBRALTER
1010, 1011, 1013
GOODMANS
1016, 1017, 1032, 1079, 1103,
1104
GORENJE
1102
GPM
1080
GRAETZ
1055
GRANADA
1017, 1032, 1048, 1074, 1079,
1100
GRADIENTE
1024, 1026, 1058
GRANDIN
1090
GRUNDIG
1031, 1066, 1068, 1072, 1115
GRUNPY
1063, 1064
HALLMARK
1062
HANSEATIC
1017, 1098
HARLEY DAVIDSON 1063
HARVARD
1029, 1064
HARMAN/KARDON 1025
HCM
1006, 1090, 1105
HINARI
1006, 1016, 1017, 1080
HISAWA
1090, 1111
HITACHI
1014, 1016, 1018, 1020, 1021,
1026, 1044, 1046, 1047, 1055,
1069, 1070, 1079, 1081, 1097
HUANYU
1078, 1104
HYPSON
1017, 1089, 1090
ICE
1079, 1089, 1103
ICES
1080
IMPERIAL
1034, 1036, 1038, 1086, 1102,
1106
INDIANA
1017
INFINITY
1025
INGELEN
1055
INNO HIT
1032
INNOVA
1017
INTEQ
1010
INTERBUY
1029
INTERFUNK
1017, 1055, 1086, 1114
INTERVISION
1017, 1029, 1043
1079, 1089
ISUKAI
1080
ITS
1103
ITT
1055
Controlling the rest of your system
JBL
JCB
KAISUI
KAMP
KAPSCH
KAWASHO
KEC
KENDO
KNEISSEL
KENWOOD
KINGSLEY
KONIG
KORPEL
KOYODA
KTV
LEYCO
LG
LIESENK&TTER
LLOYTRON
LOEWE
LOGIK
LUMA
LUXMAN
LXI
M ELECTRONIC
MAGNAVOX
MAGNADYNE
MAGNAFON
MAJESTIC
MANESTH
MARANTZ
MARK
MATSUI
MATSUSHITA
MCMICHAEL
MEDIATOR
MEGATRON
MEMOREX
METZ
MGA
MIDLAND
MINERVA
MINOKA
MINUTZ
MIVAR
MOTION
MOTOROLA
MTC
MULTITECH
1025
1001
1006, 1078, 1079, 1080, 1090,
1078
1055, 1073
1078
1064
1017
1088
1011, 1013
1078
1114
1017
1006
1013, 1019, 1064
1017, 1032, 1089, 1095
1026
1017
1014
1035, 1114
1009
1073
1026
1022, 1025, 1050, 1051, 1062
1006, 1017, 1029, 1044, 1046,
1055, 1079, 1091, 1104
1013, 1016, 1025, 1063
1043, 1086
1036, 1043, 1075
1009
1079, 1089, 1098
1013, 1017, 1025
1017
1006, 1015, 1016, 1017, 1032,
1074, 1079, 1095, 1103
1087
1020
1008, 1017
1047, 1062
1006, 1009, 1026, 1049, 1050,
1062, 1087, 1112
1075
1011, 1013, 1049, 1062
1010, 1019, 1022, 1023
1031, 1115
1105
1012
1078, 1092, 1093, 1094
1036
1041
1011, 1013, 1026, 1027, 1078,
1114
1006, 1036, 1043, 1064, 1078
09
NAD
NEC
NECKERMANN
NEI
NETSAT
NICAMAGIC
NIKKAI
NIKKO
NOBLIKO
NORDMENDE
NTC
OCEANIC
ONWA
OPTIMUS
OPTONICA
OSAKI
OSO
OSUME
OTTO
OTTO VERSAND
PALLADIUM
PANAMA
PATHE MARCONI
PATHE CINEMA
PAUSA
PENNEY
PERDIO
PHAPSODY
PHASE
PHILCO
PHONOLA
PILOT
PORTLAND
PRISM
PROFEX
PROLINE
PROSOCAN
PROTECH
PROTON
PULSAR
PYE
QUASAR
QUELLE
QUESTA
R-LINE
1051, 1057, 1062
1011, 1013, 1016, 1026, 1058
1017, 1066, 1075, 1115
1017, 1109
1017
1078
1014, 1015, 1017, 1032, 1078,
1080, 1089
1013, 1040, 1062
1036, 1043
1046, 1069, 1070, 1075, 1091
1040
1055, 1077
1064
1050, 1057, 1087
1041, 1056
1014, 1032, 1079, 1080, 1089,
1105
1080
1014, 1032, 1052
1007, 1114
1007, 1016, 1017, 1066, 1075,
1079, 1098, 1115
1102, 1106
1079, 1089
1069, 1070, 1072
1075, 1078, 1084, 1098
1006
1003, 1011, 1012, 1013, 1019,
1022, 1023, 1026, 1027, 1051,
1062, 1131
1098
1078
1014
1011, 1013, 1025, 1034, 1036,
1038, 1047, 1075, 1086, 1112
1008, 1017
1011, 1013, 1019
1011, 1019, 1040
1023
1006, 1037
1099
1022
1006, 1017, 1043, 1079, 1086,
1089, 1106, 1109
1062, 1113
1010, 1011
1008
1023, 1056, 1087
1007, 1017, 1031, 1034, 1038,
1071, 1075, 1097, 1114, 1115
1016
1017
57
En
09
Controlling the rest of your system
RANK ARENA
RBM
RCA
REALISTIC
REX
REVOX
ROADSTAR
RUNCO
SABA
SACCS
SAISHO
SALORA
SAMBERS
SAMPO
SAMSUX
SANDRA
SANSEI
SANSUI
SANYO
SBR
SCHNEIDER
SCIMITSU
SCOTCH
SCOTT
SEARS
58
En
SEG
SEI
SEI-SINUDYNE
SELECO
SEMIVOX
SEMP
SENTRA
SHOGUN
SHORAI
SSS
SIAREM
SINDYNE
SIGNATURE
SILVER
SKY
SKY-WORTH
SOLAVOX
SONITRON
SONOKO
SONOLOR
SONTEC
SOUNDESIGN
1016
1031
1011, 1018, 1022, 1023, 1039,
1041, 1128, 1129, 1130, 1131,
1132
1011, 1013, 1019, 1026, 1050,
1056, 1062, 1064
1055, 1073, 1088, 1089
1017
1006, 1080, 1089, 1106
1010, 1013, 1117
1035, 1046, 1055, 1069, 1070,
1072, 1075, 1091
1084
1006, 1089, 1109
1055
1036, 1043, 1075
1013, 1019
1019
1078
1110
1112
1016, 1032, 1048, 1050, 1052,
1074, 1075, 1100
1008, 1017, 1020
1017, 1080, 1086, 1096, 1103
1011
1062
1011, 1062, 1063, 1064, 1083
1022, 1025, 1026, 1050, 1051,
1059, 1062, 1063
1016, 1036, 1079, 1089
1043, 1075, 1095
1007
1055, 1073, 1088
1064
1051
1015
1011
1095
1011, 1064
1043, 1075
1043, 1075, 1095
1009
1016
1017
1017
1014, 1055
1074
1006, 1017
1055, 1074, 1077
1017
1062, 1063, 1064
SOUNDWAVE
SQUAREVIEW
STANDARD
STARLITE
STERN
SUNKAI
SUPERTECH
SUPREME
SUSUMU
SYLVANIA
SYMPHONIC
SYSLINE
TANDY
TASHIKO
TEC
TECHNEMA
TECHNICS
TECHNOL ACE
TECHWOOD
TEKNIKA
1017, 1106
1059
1006, 1079, 1080
1064
1055, 1073, 1088
1095, 1099
1078
1001
1080
1013, 1025
1059
1017
1032, 1041, 1055, 1079, 1080
1016, 1020, 1079
1079, 1086
1098
1023, 1087, 1121
1063
1023, 1026
1009, 1011, 1019, 1025, 1026,
1027, 1040, 1049, 1063, 1064
TELEAVIA
1072
TELEMEISTER
1098
TELETECH
1006
TELETON
1016, 1073, 1079
TENSAI
1080, 1095, 1098
TEXET
1078, 1080
THOMSON
1046, 1069, 1070, 1072, 1091
THORN
1015, 1017, 1032, 1034, 1038,
1065, 1067, 1114
TMK
1026, 1061, 1062
TOMASHI
1090
TOTEVISION
1019
TRIUMPH
1085
TUTUNG
1017, 1032, 1079
UHER
1073, 1096, 1098
ULTRA
1067
ULTRAVOX
1043
UNIVERSUM
1017, 1044, 1089, 1102
VECTOR RESEARCH 1013
VESTEL
1017
VICTOR
1016, 1024, 1053, 1087
VIDEOSAT
1086
VIDEOTECHNIC
1079
VIDIKRON
1025
VIDTECH
1011, 1016, 1062
VISION
1098
VOXSON
1055
WALTHAM
1079
WATSON
1017, 1098
WATT RADIO
1043
WARDS
1009, 1011, 1012, 1013, 1025,
1026, 1056, 1062, 1063
WEGA
1016
Controlling the rest of your system
WHITE WESTINGHOUSE 1017, 1078, 1098, 1112,
1118, 1119
YAMAHA
1011, 1013
YOKO
1017, 1079, 1101, 1109
ZANUSSI
1073
ZENITH
1009, 1010, 1040, 1112
PIONEER
1018, 1046, 1055, 1057, 1060,
1091, 1107, 1123, 1124
MD PLAYER
Manufacturer
SONY
KENWOOD
SHARP
ONKYO
ORION
DENON
PIONEER
CD-R
Code
5401
5402,5407
5403
5404
5406
5405
5408
LD PLAYER
Manufacturer
AKAI
BBK
CYRUS
DENON
DISCO VISION
FUNAI
HITACHI
HONG DENG
IDALL
KEBAO
MARANTZ
MITSUBISHI
NAD
PANASONIC
PHILIPS
RADIOLA
ROWA
SALORA
SEGA
SHARP
SHINCO
SMC
SONY
SUPER
TELEFUNKEN
TOSHIBA
PIONEER
CD
DVD
Code
5222
5224
5207
5202
5201
5217
5201
5213
5219
5215
5203, 5205
5202
5202
5210
5203, 5207, 5209
5207
5212
5203
5201
5221
5211
5220
5204, 5206, 5216
5218
5215
5202
5223
5201,5202, 5208
5214
09
CD PLAYER
CD
CD-R
Manufacturer
Code
AIWA
5016, 5021
AKAI
5014, 5020, 5032
ANAM
5041
ARCAM
5021
AUDIOLAB
5021
AUDIOMECA
5021
AUDIO TON
5021
BESTAR
5022
BURMESTER
5045
CALIFORNIA AUDIO LABS 5004
CARVER
5021, 5025, 5046
CONDOR
5018, 5022
CURTIS MATHES
5004
CYRUS
5021
DENON
5002, 5006, 5040, 5060
DKK
5001
DUAL
5031
DYNAMIC BASS
5025
EMERSON
5038
EROICA
5053, 5054
FANTASIA
5051
FISHER
5024, 5025
GARRARD
5044, 5045
GENEXXA
5005, 5038
GOLDSTAR
5043, 5051
GRUNDIG
5021
HARMAN/KARDON 5021, 5023
HITACHI
5005
INKEL
5015, 5026, 5046
JVC
5011
KENWOOD
5003, 5008, 5029, 5056, 5057,
5062
KRELL
5021
LINN
5021
LUXMAN
5036
LXI
5038
MAGNAVOX
5021, 5038
MARANTZ
5004, 5009, 5017, 5021, 5026
MATSUI
5021
MCS
5004
MEMOREX
5022
MERIDIAN
5021
MICROMEGA
5021
MISSION
5021
MITSUBISHI
5014, 5020
MTC
5045
NAD
5001
NAIM
5021
NIKKO
5024, 5041, 5051
NSM
5021
59
En
09
Controlling the rest of your system
ONKYO
OPTIMUS
ORION
PANASONIC
PARASOUND
PHILIPS
PMG
POPPY
PROTON
QED
QUAD
QUASAR
RCA
REALISTIC
REVOX
ROTEL
SAE
SANSUI
SANYO
SCHNEIDER
SCOTT
SEARS
SHARP
SHERWOOD
SONY
SOUDESIGN
TASCAM
TEAC
TECHNICS
THORENS
TOSHIBA
UNIVERSUM
YAMAHA
YORX
VICTOR
WARDS
PIONEER
TAPE DECK
60
En
Manufacturer
ADC
AIWA
AKAI
ANAM
ARCAM
CARVER
DENON
DUAL
5012, 5013, 5042, 5059
5001, 5005, 5008, 5019, 5025,
5038, 5045, 5046, 5048
5061
5004, 5037
5045
5021, 5055
5022
5022
5021
5021
5021
5004,
5010, 5025, 5038
5025, 5026, 5045
5021
5021, 5045
5021
5021, 5033, 5038
5025, 5039
5018
5038
5038
5008, 5026, 5058
5015, 5026, 5031
5001, 5027, 5050
5019
5045
5024, 5026, 5044, 5045
5004, 5034, 5037
5021
5049
5021
5007, 5028
5047
5011
5010, 5021
5005, 5030, 5035, 5038, 5048,
5052, 5063
CD-R
Code
6013
6002, 6022, 6017, 6018
6015, 6016
6035
6005
6002, 6028
6005, 6039
6037
CD
DYNAMIC BASS
EROICA
FISHER
GARRARD
GOLDSTAR
GRUNDIG
HARMON/KARDON
INKEL
JVC
KENWOOD
KYOCERA
LOTTE
LUXMAN
MAGNAVOX
MARANTZ
MEMOREX
MITSUBISHI
NAKAMICHI
NIKKO
OLYMPUS
ONKYO
OPTIMUS
PANASONIC
PHILIPS
RCA
RENAISSANCE
REVOX
SAMSUNG
SANSUI
SANYO
SHARP
SONIC
SONY
TEAC
TECHNICS
THORENS
VICTOR
WARDS
YAMAHA
PIONEER
6028
6041
6028
6036
6036
6002
6002, 6014
6003
6027, 6030, 6031
6003, 6004, 6019, 6024, 6025
6013
6034
6029
6002
6002
6008, 6009
6016
6020
6035
6029
6010, 6011, 6032
6001, 6021
6023
6002
6028
6040
6002
6038
6002
6028
6019
6036
6012, 6026, 6033
6038
6023
6002
6027, 6030
6001
6006, 6007, 6019
6001, 6008, 6009
6021,
DVD PLAYER
Manufacturer
TOSHIBA
SONY
PANASONIC
KENWOOD
JVC
SAMSUNG
AKAI
HARMAN/KARDON
DVD
Code
5302
5306
5301, 5322
5307
5311, 5318
5313
5316
5314
Controlling the rest of your system
MAGNAVOX
MITSUBISHI
ONKYO
PROSCAN
RCA
SHARP
THETA DIGITAL
TECHNICS
THOMSON
YAMAHA
PHILIPS
ZENITH
PIONEER
5302
5303
5302, 5317, 5319
5304
5304
5320
5312
5301
5310
5301, 5309
5302, 5308
5302, 5315
5305, 5312, 5321
5322
AMPLIFIER
Manufacturer
AUDIOLAB
DENON
GRUNDIG
MARANTZ
MICROMEGA
PHILIPS
PIONEER
REVOX
TANDBERG
THORENS
YAMAHA
09
EROICA
FANTASIA
FERGUSON
FINE ARTS
FISHER
GARRARD
GOLDSTAR
GOODMANS
GP AUDIO
GRUNDIG
HARMAN/KARDON
INKEL
JBL
JVC
KENWOOD
TUN
LOTTE
LUXMAN
MAGNAVOX
MARANTZ
MCINTOSH
MCS
MCSILVER
MICROMEGE
NIKKO
OPTIMUS
ONKYO
PALLADIUM
PANASONIC
PHILIPS
Code
8005
8002
8005
8005
8005
8005
8004
8005
8003
8005
8001, 8006
MISC AUDIO
TUN
Manufacturer
Code
JERROLD
8201, 8203
STARCOM
8201
SCIENTIFIC ATLANTA 8202
RECEIVERS
TUN
Manufacturer
ADC
AIWA
AKAI
ANAM
ARCAM
AUDIOLAB
CAPETRONIC
CARVER
CURTIS
DAEWOO
DENON
DUAL
Code
7042
7012, 7023, 7031, 7055, 7064
7011, 7027
7010, 7046
7018, 7048
7059
7042
7055, 7059
7008
7032
7001, 7056, 7058
7040
PHONOTREND
QUASAR
RCA
RENAISSANCE
REVOX
ROADSTAR
SABA
SAISHO
SAMSUNG
SANSUI
SANYO
SCHNEIDER
SHARP
SHERWOOD
SOUNDESIGN
SONY
TAE KWANG
TEAC
TECHNICS
TELEFUNKEN
THORENS
7005
7037
7042
7059
7028
7032, 7034, 7035
7010
7027
7033
7018, 7059
7009, 7051
7038, 7040
7009
7007, 7036, 7042
7003, 7017, 7025, 7026, 7044,
7053, 7063, 7066
7037, 7039
7021
7030, 7042, 7055, 7059
7004, 7018, 7055, 7059
7020
7004
7037
7018, 7059
7032, 7037, 7046
7017, 7034, 7042, 7049, 7052
7013, 7029
7050
7004, 7024, 7041
7018, 7030, 7045, 7048, 7051,
7055, 7059
7038
7004
7006, 7042
7043
7018
7027
7042
7027
7010
7027, 7055
7028
7042
7017
7038
7049
7015, 7054, 7057, 7060
7034
7010, 7035
7004, 7062, 7065
7019, 7024, 7041, 7061, 7062,
7065
7018, 7059
61
En
09
Controlling the rest of your system
UHER
VICTOR
WARDS
YAMAHA
PIONEER
VCR
Manufacturer
PHILIPS
PANASONIC
THOMSON
SONY
JVC
GRUNDIG
AKAI
HITACHI
TOSHIBA
MITSUBISHI
SHARP
ORION
SANYO
FERGUSON
BLAUPUNKT
NOKIA
ADMIRAL
ADVENTURA
AIKO
AIWA
AKIBA
ALBA
AMBASSADOR
AMERICA ACTION
AMERICAN HIGH
AMSTRAD
ANAM
62
En
ANAM NATIONAL
ANITECH
ASA
ASHA
ASUKA
AUDIOVOX
7027, 7042, 7050
7007
7002, 7006, 7008
7016, 7017
7002, 7008, 7014, 7022, 7042,
7047, 7050, 7052
VCR
Code
2015, 2035, 2074, 2075
2015, 2042, 2053, 2054,
2055, 2087
2021, 2064, 2074
2001, 2009, 2012, 2013, 2014,
2015
2008, 2021, 2033, 2049, 2050,
2074, 2080
2003, 2005, 2007, 2010, 2034,
2035, 2048, 2050, 2054, 2069,
2071, 2075
2021, 2029, 2038, 2060, 2063
2001, 2004, 2021, 2022, 2043,
2056, 2057
2021, 2023, 2024, 2035, 2074
2023, 2027, 2033, 2035, 2045
2027, 2073
2002, 2004, 2016, 2036, 2046,
2052, 2070, 2072, 2078
2025, 2026, 2037, 2057
2021, 2039, 2064, 2065
2003, 2005, 2010, 2014, 2041,
2042, 2048, 2054, 2055, 2075
2025, 2037, 2038, 2057
2027, 2052
2001
2059
2001, 2017, 2062, 2070, 2072
2034
2011, 2034, 2052, 2059, 2063,
2072
2011
2059
2015
2001, 2059, 2067, 2068
2017, 2042, 2054, 2057, 2059,
2082, 2084
2042, 2054, 2087
2034
2017, 2035
2057
2017
2017
BAIRD
2001, 2021, 2037, 2039
BASIC LINE
2011, 2034, 2059
BEAUMARK
2057
BELL & HOWELL
2037
BRANDT
2047, 2064, 2065
BRANDT ELECTRONIC 2021
BROKSONIC
2002, 2040, 2046, 2052, 2078
BUSH
2034, 2052, 2059, 2072
CALIX
2017
CANON
2015
CAPEHART
2011
CARVER
2035
CATRON
2011
CCE
2034, 2059
CGE
2001
CIMLINE
2034
CINERAL
2059
CITIZEN
2017, 2059
CLATRONIC
2011
COLT
2034
COMBITECH
2072
CONDOR
2011
CRAIG
2017, 2026, 2034, 2057, 2058
CROWN
2011, 2034, 2059
CURTIS MATHES
2015, 2021, 2032, 2042
CYBERNEX
2057
CYRUS
2035
DAEWOO
2011, 2024, 2025, 2059, 2083
DANSAI
2034
DAYTRON
2011
DECCA
2001, 2035
DE GRAAF
2022, 2043
DENON
2022
DUAL
2021
DUMONT
2001, 2035, 2037
DYNATECH
2001
ELBE
2018
ELCATECH
2034
ELECTROHOME
2017
ELECTROPHONIC 2017
EMEREX
2012
EMERSON
2001, 2002, 2017, 2023, 2040,
2046, 2051, 2052, 2059, 2078,
2083
ESC
2057, 2059
FIDELITY
2001
FINLANDIA
2035, 2037
FINLUX
2001, 2022, 2035, 2037
FIRSTLINE
2017, 2023, 2024, 2034, 2052
FISHER
2025, 2026, 2030, 2037
FRONTECH
2011
FUJI
2015
Controlling the rest of your system
FUNAI
2001
GARRARD
2001
GE
2015, 2027, 2032, 2057
GEC
2035
GENERAL
2011, 2028
GOLDHAND
2034
GOLDSTAR
2017, 2018, 2053, 2079
GOODMANS
2001, 2017, 2034, 2059, 2075
GO VIDEO
2077, 2081
GRAETZ
2005, 2021, 2037, 2057
GRANADA
2025, 2035, 2037
GRADIENTE
2001, 2008
GRANDIN
2001, 2017, 2034
HANSEATIC
2017
HARMAN/KARDON 2018, 2035
HARLEY DAVIDSON 2001
HARWOOD
2034
HCM
2034
HEADQUARTER
2025
HINARI
2004, 2034, 2057, 2072
HI-Q
2026
HUGHES NETWORK SYSTEMS 2022
HYPSON
2034
IMPERIAL
2001
INGERSOL
2004
INTERFUNK
2035
ITT
2005, 2021, 2025, 2037, 2038,
2057, 2074
ITV
2017, 2059
JENSEN
2021
KAISUI
2034
KEC
2017, 2059
KENDO
2038, 2052
KENWOOD
2018, 2021, 2033
KLH
2034
KODAK
2015, 2017
KORPEL
2034
LAYCO
2034
LENCO
2059
LG
2079
LLOYD’S
2001, 2051
LOEWE
2004, 2005, 2017, 2035
LOGIK
2004, 2034, 2057
LUXOR
2023, 2025, 2027, 2037, 2038
LXI
2017
M ELECTRONIC
2001
MAGNASONIC
2059
MAGNAVOX
2001, 2015, 2019, 2035
MAGNIN
2057
MANESTH
2024, 2034
MARANTZ
2003, 2005, 2015, 2035
MARTA
2017
09
MATSUI
2004, 2016, 2036, 2052, 2070,
2072
MATSUSHITA
2015, 2042, 2055
MEI
2015
MELECTRONIC
2018
MEMOREX
2001, 2015, 2017, 2019, 2025,
2026, 2027, 2037, 2052, 2057,
2062, 2085, 2087, 2088
MEMPHIS
2034
METZ
2003, 2005, 2017, 2042, 2048,
2055, 2069
MGA
2023, 2057
MGN TECHNOLOGY 2057
MINCRVA
2048
MINERVA
2005, 2010, 2048
MINOLTA
2022
MOTOROLA
2015, 2027
MTC
2001, 2057
MULTITECH
2001, 2034
MURPHY
2001
NAD
2031
NATIONAL
2054
NEC
2018, 2020, 2021, 2033, 2037
NECKERMANN
2035
NESCO
2034
NIKKO
2017
NIKON
2014
NOBLEX
2057
NOKIA
2021, 2025, 2037, 2038, 2057
NORDMENDE
2021, 2061, 2064, 2065, 2074
OCEANIC
2001, 2021
OKANO
2063, 2070
OLYMPUS
2015, 2054
OPTIMUS
2017, 2027, 2031, 2037, 2042,
2077, 2086, 2087, 2088
OSAKI
2001, 2017, 2034
OTTO VERSAND
2035
PALLADIUM
2005, 2017, 2021, 2034
PATHE MARCONI 2021
PATHE CINEMA
2016
PENTAX
2022
PENNY
2015, 2017, 2018, 2020, 2022,
2057
PERDIO
2001
PHILCO
2015, 2018, 2052, 2078
PHONOLA
2035
PILOT
2017
PORTLAND
2011
PROFEX
2066
PROFITRONIC
2057
PROLINE
2001
PROSCAN
2032
63
En
09
Controlling the rest of your system
PROTEC
PULSAR
PYE
QUARTER
QUARTZ
QUASAR
QUELLE
RADIO SHACK
RADIOLA
RADIX
RANDEX
RCA
REALISTIC
REX
RFT
RICOH
ROADSTAR
RUNCO
SABA
SAISHO
SALORA
SANKY
SANSUI
SAMSUNG
SAVILLE
SBR
SCHAUB LORENZ
SCHNEIDER
SCOTT
SEARS
64
En
SEG
SEI
SELECO
SEMP
SENTRA
SHINTOM
SHOGUN
SHORAI
SIEMENS
2017, 2030, 2035
SILVA
SINGER
SINUDYNE
SOLAVOX
SONOLOR
SONTEC
STS
SUNKAI
2034
2019
2035
2025
2025
2015, 2042, 2087
2035
2001, 2085
2035
2017
2017
2015, 2022, 2027, 2032, 2038,
2057
2001, 2015, 2017, 2025, 2026,
2027, 2037
2021, 2074
2075
2014
2017, 2034, 2057, 2059
2019
2021, 2049, 2050, 2061, 2064,
2065, 2074
2004, 2016, 2036, 2052
2023, 2025, 2038
2019, 2027
2001, 2021, 2033, 2052, 2058,
2078
2024, 2057, 2076, 2077
2072
2035
2001, 2005, 2021, 2037
2001, 2034, 2035
2023, 2024, 2040, 2046
2001, 2015, 2017, 2022, 2025,
2026, 2037
2057, 2066
2004, 2035
2021
2024
2011
2034, 2037
2057
2004
2003, 2005, 2010
2037, 2048
2017
2024, 2034
2004, 2035
2011
2025
2017
2022
2070
SUNSTAR
SUNTRONIC
SYLVANIA
SYMHONIC
TASHIKO
TATUNG
TEAC
TEC
TECHNICS
TEKNIKA
TELEAVIA
TELEFUNKEN
TENOSAL
TENSAI
THOMAS
THORN
TMK
TOTEVISION
TOWADA
UHER
UNITECH
UNIVERSUM
2001
2001
2001, 2015, 2023, 2035
2001
2001
2001, 2021, 2035
2001, 2021
2011
2015, 2042, 2054
2001, 2015, 2007, 2017, 2028
2021
2021, 2047, 2058, 2064, 2074
2034
2001, 2066
2001
2016, 2021, 2037
2051, 2057
2017, 2057
2066
2057
2057
2001, 2006, 2010, 2017, 2035,
2038, 2048, 2057, 2067
VECTOR
2024
VECTOR RESEARCH 2018, 2020
VICTOR
2008, 2021, 2033
VIDEO CONCEPTS 2020, 2024
VIDEOSONIC
2057
WARDS
2001, 2015, 2022, 2026, 2027,
2032, 2034, 2035, 2057
WHITE WESTINGHOUSE 2052, 2059
XR-1000
2001
XR-1001
2015
XR-1002
2034
YAMAHA
2018
YAMISHI
2034
YOKAN
2034
YOKO
2011, 2057
ZENITH
2001, 2014, 2019, 2052, 2078
PIONEER
2031, 2033, 2035, 2044, 2056
SATELLITE TUNER
Manufacturer
ABSAT
AST
ALBA
ALDES
AMSTRAD
ANKARO
ANTTRON
TV
TVC
Code
4006
4027
4029, 4034, 4037, 4052
4019
4003, 4016, 4025, 4038, 4039,
4042
4013, 4019, 4030, 4044
4009, 4034
Controlling the rest of your system
ARMSTRONG
4015
ASTRA
4005
ASTRO
4008, 4039, 4045
AVALON
4031
AXIS
4030, 4046
BT
4053
BEKO
4010
BEST
4030
BLAUPUNKT
4008
BOCA
4015, 4043
BRAIN WAVE
4022
BRITISH SKY BROADCASTING 4058
BUSH
4002
CNT
4045
CAMBRIDGE
4024
CANAL SATELLITE 4059
CANAL+
4059
CHANNEL MASTER 4029
COMLINK
4019
CONNEXIONS
4031
CROWN
4015
CYRUS
4011
D-BOX
4054
DDC
4029
DNT
4011, 4031
ECHOSTAR
4031, 4036, 4061
EMANON
4034
FTE HUMAX
4060
FERGUSON
4002, 4009, 4010, 4023
FIDELITY
4016
FINLUX
4005, 4024, 4032, 4037
FRACARRO
4061
FREECOM
4034
FUBE
4030, 4031, 4034
G-SAT
4009
GALAXIS
4019, 4057, 4060
GENERAL INSTRUMENT 4012
GOLD BOX
4059
GOODING
4048
GOODMANS
4010
GRUNDIG
4008, 4010, 4048
HINARI
4009
HIRSCHMANN
4008, 4032, 4039, 4040, 4049
HITACHI
4037
HOUSTON
4053
HUTH
4013, 4015, 4019, 4026
ITT
4005
INVIDEO
4061
INTERVISION
4050
JVC
4048
JOHANSSON
4022
KATHREIN
4004, 4006, 4008, 4011, 4035,
4041
09
KREISELMEYER
KYOSTAR
LA SAT
LENCO
LENNOX
LUPUS
LUXOR
MANHATTAN
MARANTZ
MASPRO
MATSUI
MEDIASAT
MEDIAMARKT
MINERVA
MORGAN’S
NAVEX
NEUHAUS
NEUSAT
NEWHAUS
NIKKO
NOKIA
NORDMENDE
ORBITECH
OXFORD
PACE
PALLADIUM
PALSAT
PANDA
PHILIPS
PHONOTREND
PIONEER
PLANET
PROMAX
PROSAT
QUADRAL
RADIOLA
RADIX
RFT
SAT
SABA
SABRE
SAGEM
SALORA
SATCOM
SATEC
SATMASTER
SATPARTNER
SCHWAIGER
SEEMANN
4008
4034
4043, 4045
4034
4050
4030
4005, 4049
4037, 4045, 4050
4011
4004, 4023
4024, 4048
4059
4015
4048
4015, 4043
4022
4039
4057
4013
4028
4005, 4032, 4037, 4049, 4054,
4063
4029
4039
4024
4002, 4009, 4014, 4023, 4037,
4055, 4058
4048
4039
4037
4007, 4011, 4020, 4037, 4048,
4059
4019, 4050
4021, 4059
4061
4037
4019
4029, 4044
4011
4031, 4064
4011, 4013, 4019
4027, 4038
4023, 4045
4037
4056
4005
4026, 4051
4009
4026
4022, 4034, 4040, 4045
4009, 4041
4031, 4046
65
En
09
Controlling the rest of your system
SEG
SIEMENS
SKYMASTER
SONY
STRONG
SUNSTAR
TPS
TANTEC
TECHNISAT
TECHNILAND
TELEFUNKEN
TELEKA
TELESAT
THOMSON
TONNA
TRIAD
TRIASAT
UNITOR
UNIVERSUM
VENTANA
VORTEC
VTECH
WINERSAT
WISI
XSAT
XCOM MULTIMEDIA
ZEHNDER
CABLE TV
66
En
4030, 4034
4008
4019, 4044, 4051
4017, 4018
4062
4043
4056
4023, 4037
4001, 4039
4026
4034
4015, 4052
4051
4037, 4059
4026, 4053
4027
4040
4022
4008, 4049
4011
4034
4027
4022
4008, 4027, 4031, 4037
4006, 4065
4065
4033, 4045, 4047
TV
JASCO
JERROLD
TVC
Manufacturer
Code
ABC
3002, 3003, 3004, 3006, 3008
ANDOVER
3037
BELL & HOWELL
3006
BIRGMINGHAM CABLE
COMMUNICATION 3020
BRITISH TELECOM 3002, 3012
CABLETIME
3016, 3019, 3025, 3029
CONTEC
3009
CLYDE
3011
CRYPTOVISION
3038
DAEHAN
3043
DAERYUNG
3003
DECSAT
3027
EVERQUESST
3007
FILMNET
3028
FRANCE TELECOM 3030
GEC
3011
GEMINI
3007
GENERAL INSTRUMENT 3004, 3020, 3031, 3046
GOLDSTAR
3014, 3047
GRUNDIG
3035
HITACHI
3004
3007
3002, 3004, 3005, 3006, 3007,
3020, 3031, 3046
3044
3001
3009, 3028
3041
3009
3039
3001, 3013
3001
3001
LG ALPS
MEMOREX
MNET
NOW
OAK
PACIFIC
PANASONIC
PARAGON
PULSAR
PVP STEREO VISUAL
MATRIX
3002
PIONEER
3010, 3014, 3018, 3036
QUASAR
3001
RADIO SHACK
3007
REMBRANDT
3004
RUNCO
3001
SAMSUNG
3014, 3040
SATBOX
3024
SIGNAL
3007
SIGNATURE
3004
STS
3015
SALORA
3026
SCIENTIFIC
3003, 3032, 3049
SCIENTIFIC ATLANTA 3003, 3008, 3021
SEAWOO
3045
STARCOM
3002, 3007
STARGATE
3007
STARQUEST
3007
TAIHAN
3043
TELESERVICE
3022
TELE+1
3028
TUDI
3023
TUSA
3007
TOCOM
3005
TONGKOOK
3042, 3048
TOSHIBA
3001
UNITED CABLE
3002
VIDEOWAY
3017
VISICABLE+
3033
WESTMINSTER
3012
WOLSEY GENE
3037
ZENITH
3001, 3034
Additional information
10
Troubleshooting
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is
something wrong with this component, check the points below. Sometimes the trouble may lie in
another component. Investigate the other components and electrical appliances being used. If the
trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer
authorized service center or your dealer to carry out repair work.
Problem
Remedy
The power does not turn on.
• Connect the power plug to the wall outlet.
• Disconnect the power plug from the outlet, and insert again.
• Make sure there are no loose strands of speaker wire touching
the rear panel. This could cause the receiver to shut off
automatically.
No sound is output when a
function is selected.
• Make sure the component is connected correctly (refer to
pages 13–18).
• Press MUTE on the remote control to turn muting off.
• Adjust the MASTER VOLUME.
• Press the MONITOR button to turn monitoring off.
No image is output when a
function is selected.
• Make sure the component is connected correctly (refer to
pages 13–18).
• Select the correct component (use the MULTI JOG/INPUT
SELECTOR dial or the MULTI CONTROL buttons on the remote).
Considerable noise in radio
broadcasts.
• Tune in the correct frequency.
• Connect the antenna (refer to page 18).
• Route all cables away from the antenna terminals and wires.
• Fully extend the FM wire antenna, position for best reception,
and secure to a wall.
• Connect an outdoor FM antenna (refer to page 18).
• Adjust the direction and position for best reception.
• Connect an additional internal or external AM antenna (refer
to page 19).
• Turn off the equipment causing the noise or move it away from
the receiver.
• Place the antenna farther away from the equipment causing
the noise.
Broadcast stations cannot be
selected automatically.
• Connect an outdoor antenna (refer to page 18).
67
En
10
Additional information
Problem
Remedy
No sound from surround or
center speakers.
• Refer to Speaker setting on page 37 to check the speaker
settings.
• Refer to Setting the relative volume level of each channel on
page 42to check the speaker levels.
• Connect the speakers properly (refer to page 19–21).
No sound from surround back
speakers.
• Refer to Surround back speaker setting on page 40 to check
the surround back speaker settings.
• Refer to the table on page 31 to make sure the 6.1 channel
setting and the sound mode are set for surround back sound.
Noise during playback of a
cassette deck.
• Move the cassette deck further from your receiver, until the
noise disappears.
Sound is produced from other
components, but not from LD or
DVD player.
• Set the SIGNAL SELECT to AUTO, DIGITAL or ANALOG
according to the type of connections made. (refer to page 32).
• Set the digital input settings correctly (refer to page 41).
• Make digital connections (refer to page 14) and set the
SIGNAL SELECT to DIGITAL (refer to page 32).
• Refer to the instruction manual supplied with the DVD player.
No sound is output or a noise is
output when software with DTS
is played back.
• Set the digital volume level of the player to full, or to the
neutral position.
When a search is performed by • This is not a malfunction, but be sure to turn the volume
a DTS compatible CD player
down to prevent the output of loud noise from your speakers.
during playback, noise is output.
Can’t operate the remote
control.
• Replace the batteries (refer to page 6).
• Operate within 23 feet ( 7 m), 30° of the remote sensor on the
front panel (refer to page 6).
• Remove the obstacle or operate from another position.
• Avoid exposing the remote sensor on the front panel to direct
light.
The display is dark or off.
• Press FL DIMMER on the remote control repeatedly to return
to the default.
If the unit does not operate normally due to external effects such as static electricity disconnect the
power plug from the outlet and insert again to return to normal operating conditions.
68
En
Additional information
10
Specifications
Video Section
Amplifier Section
Input (Sensitivity/Impedance)
VCR/DVR, DVD/LD, TV/SAT ............. 1 Vp-p/75 Ω
Continuous average power output of 110 watts*
per channel, min., at 8 ohms, from 20 Hz to
20,000 Hz with no more than 0.2 %** total
harmonic distortion (front).
Continuous Power Output
Front ...................................... 110 W per channel
(1kHz, 1.0 %, 8 Ω)
Center .......................... 110 W (1kHz, 1.0 %, 8 Ω)
Surround ............................... 110 W per channel
(1kHz, 1.0 %, 8 Ω)
Input (Sensitivity/Impedance)
CD, VCR/DVR, CD-R/TAPE/MD,
DVD/LD, TV/SAT ........................... 200 mV/47 kΩ
Frequency Response
CD, VCR/DVR, CD-R/TAPE/MD, DVD/LD,
TV/SAT ............................ 5 Hz to 100,000 Hz dB
Output (Level/Impedance)
VCR/DVR REC, CD-R/TAPE/
MD REC ....................................... 200 mV/2.2 kΩ
Tone Control
BASS .......................................... ± 6 dB (100 Hz)
TREBLE ...................................... ± 6 dB (10 kHz)
LOUDNESS .................................. +9 dB/+9 dB
(100 Hz/10 kHz)
Signal-to-Noise Ratio (IHF, short
circuited, A network)
CD, VCR/DVR, CD-R/TAPE/MD,
DVD/LD, TV/SAT ......................................... 96 dB
Output (Level/Impedance)
VCR/DVR ........................................... 1 Vp-p/75 Ω
Frequency Response
VCR/DVR, DVD/LD,
+0
TV/SAT ] MONITOR ......... 5 Hz to 7 MHz – 3 dB
Signal-to-Noise Ratio ................................. 55 dB
Cross Talk .................................................... 55 dB
FM Tuner Section
Frequency Range ............. 87.5 MHz to 108 MHz
Usable Sensitivity ................ Mono:13.2 dBf, IHF
(1.3 µV/ 75 Ω)
50 dB Quieting Sensitivity .......... Mono: 20.2 dB
Stereo: 38.6 dBf
Signal-to-Noise Ratio ..................... Mono: 73 dB
(at 85 dBf)
Stereo: 70 dB (at 85 dBf)
Distortion ........................... Stereo: 0.5 % (1 kHz)
Alternate Channel Selectivity .................... 60 dB
(400 kHz)
Stereo Separation ......................... 40 dB (1 kHz)
Frequency Response .................. 30 Hz to 15 kHz
(±1 dB)
Antenna Input (DIN) .............. 75 Ω unbalanced
AM Tuner Section
Frequency Range .............. 530 kHz to 1,700 kHz
Sensitivity (IHF, Loop antenna) ............ 350 µV/m
Selectivity .................................................... 25 dB
Signal-to-Noise Ratio ................................. 50 dB
Antenna ........................................ Loop antenna
Signal-to Noise Ratio [EIA, at 1 W (1
kHz)]
CD, VCR/DVR, CD-R/TAPE/MD,
DVD/LD, TV/SAT ......................................... 79 dB
69
En
10
Additional information
Miscellaneous
Power Requirements ................. AC 120 V, 60Hz
Power Consumption ..................... 300W, 420 VA
In Standby ................................................ 1 W
AC Outlet .................. 100 W MAX. (SWITCHED)
Dimensions ..... 420 (W) x 158 (H) x 401 (D) mm
(16-9/16 (W) x 6-4/16
(H) x 15-6/16 (D) in.)
Weight (without package) ....................... 10.5 kg
(23.1 lb)
Furnished Parts
AM loop antenna ................................................ 1
FM wire antenna ................................................ 1
Dry cell batteries (AA size IEC LR6) .................. 2
Remote control ................................................... 1
Operating instructions ...................................... 1
Specifications and the design are subject to
possible modifications without notice, due to
improvements.
* Measured pursuant to the Federal Trade
Commission’s Trade Regulation rule on Power
Output Claims for Amplifiers.
** Measured by Audio Spectrum Analyzer.
70
En
Cleaning the unit
•
Use a polishing cloth or dry cloth to wipe
off dust and dirt.
•
When the surfaces are dirty, wipe with a
soft cloth dipped in some neutral cleanser
diluted five or six times with water, and wrung
out well, and then wipe again with a dry cloth.
Do not use furniture wax or cleansers.
•
Never use thinners, benzine, insecticide
sprays or other chemicals on or near this unit,
since these will corrode the surfaces.
Additional information
10
71
En
Should this product require service in the U.S.A. and you wish to locate the nearest Pioneer
Authorized Independent Service Company, or if you wish to purchase replacement parts,
operating instructions, service manuals, or accessories, please call the number shown below.
800–421–1404
Please do not ship your product to Pioneer without first calling the Customer Service Department
at the above listed number for assistance.
PIONEER ELECTRONICS SERVICE, INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 1760, LONG BEACH,
CA 90801-1760, U.S.A.
For warranty information please see the Limited Warranty sheet included with your product.
Should this product require service in Canada, please contact a Pioneer Canadian Authorized
Dealer to locate the nearest Pioneer Authorized Service Company in Canada.
Alternatively, please contact the Customer Service Department at the following address:
PIONEER ELECTRONICS (USA) INC.
Customer Service Department
300 Allstate Parkway, Markham, Ontario L3R OP2
(905) 479-4411
1-877-283-5901
For warranty information please see the Limited Warranty sheet included with your product.
Si ce produit doit être réparé au Canada, veuillez vous adresser à un distributeur autorisée
Pioneer au Canada pour obtenir le nom de la Société de Service Autorisée Pioneer le plus près de
chez vous. Ou encore, veuillez vous communiquer avec le Service de Clientèle de Pioneer:
Pioneer électroniques du Canada, Inc.
Département de service au consommateurs
300 Allstate Parkway, Markham, Ontario L3R OP2
(905) 479-4411
1-877-283-5901
Pour obtenir des renseignements sur la garantie, veuillez vous reporter au feuillet sur la Garantie
Limitée gui accompagne le produit.
Published by Pioneer Corporation.
Copyright © 2002 Pioneer Corporation.
All rights reserved.
PIONEER CORPORATION
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS [USA] INC.
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A.
PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway, Markham, Ontario L3R OP2, Canada
PIONEER EUROPE NV
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11
PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: [03] 9586-6300
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.
San Lorenzo 1009 3er Piso Desp. 302 Col. Del Valle Mexico D.F. C.P. 03100
TEL: 55-688-52-90
<TSWZF/02B00001>
Printed in
<XRB3018-A>
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement