Dinstar DWG2008 Specifications

Add to my manuals
51 Pages

advertisement

Dinstar DWG2008 Specifications | Manualzz

 

 

 

 

 

 

 

 

 

DWG Series GSM/CDMA VoIP Gateway 

User Manual 

(Version: 2.0) 

 

 

 

 

Dinstar Technologies Co., Ltd.

 

Address: Floor 6, Guoxing Building, Changxing Road, Nanshan District, Shenzhen, China 518057  

Telephone: +86 755 6130 2265 

Fax:               +86 755 2645 6659 

Emails:        [email protected][email protected] 

Website:  www.dinstar.com

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

 

Content 

Chapter 1 Equipment introduction ...................................................................................................2 

1.1 Introduction........................................................................................................................2 

1.2 Scenario of products...........................................................................................................2 

1.3 Product appearance ...........................................................................................................3 

1.4 Functions and features .......................................................................................................4 

1.4.1 Protocol standards...................................................................................................4 

1.4.2 System functions .....................................................................................................4 

1.4.3 Industrial

 

Standards ................................................................................................5 

1.4.4 General hardware specification ..............................................................................5 

1.5 Structure of product ...........................................................................................................5 

1.5.1 Front view ................................................................................................................6 

1.5.2 Rear view .................................................................................................................6 

1.6 Restore factory setting .......................................................................................................7 

Chapter 2 Equipment installation .....................................................................................................8 

2.1 Installation notice...............................................................................................................8 

2.2 Installation procedure ........................................................................................................9 

2.2.1 Install SIM card ........................................................................................................9 

2.2.2 Antenna installation ................................................................................................9 

2.2.3 Connect cable of equipment ...................................................................................9 

2.3 Establish remote login environment................................................................................10 

Chapter 3 Network configuration ...................................................................................................11 

3.1 Preparation .......................................................................................................................11 

3.2 Attentions .........................................................................................................................11 

3.3 General prefix code for private service............................................................................12 

3.4 Static IP Configuration......................................................................................................12 

3.5 DHCP configuration ..........................................................................................................13 

Chapter 4 WEB configuration..........................................................................................................14 

4.1 Preparation .......................................................................................................................14 

4.2 log in WEB interface .........................................................................................................14 

4.3 WEB configuration............................................................................................................15 

4.3.1 WEB introduce.......................................................................................................15 

4.3.2 System Information ...............................................................................................16 

4.3.3 Network configuration ..........................................................................................18 

4.3.4 mobile configuration .............................................................................................22 

4.3.5 System Configuration ............................................................................................32 

4.3.6 Tools .......................................................................................................................45 

Chapter 5 FAQ .................................................................................................................................48 

 

Glossary ..........................................................................................................................................50 

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Chapter 1 Equipment introduction

 

This chapter mainly introduces functions and structures of DWG (Dinstar wireless VoIP Gateway)  series GSM/CDMA wireless VoIP gateways, which are named as DWG2001/DWG2004/DWG2008. 

1.1 Introduction 

DWG2001/DWG2004/DWG2008 serial is full functions VoIP gateway based on IP and GSM/CDMA  wireless  network.  DWG200X  provides  a  flexible  network  configuration,  powerful  features,  and  good voice quality. It works for carrier grade, enterprise, SOHO, residential users for cost‐effective  solution. 

1.2 Scenario of applications of products

DWG2001/DWG2004/DWG2008 provides access of GSM/CDMA network.                                                                           

With  the  development  of  users  and  telecom  service,  mobile  network  and  fixed  network  integration will be steadily increasing. DWG2001/DWG2004/DWG2008 provides high quality VoIP  service.  DWG2001/DWG2004/DWG2008  perfectly  meets  the  requirement.  This  is  a  scenario  shown as figure 1‐1 

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

DWG2004/DWG2008 can be implemented as VoIP call termination in VoIP operation, the  solution shown as figure 1‐2 

 

1.3 Product appearance 

Figure 1‐2 

                                 

Figure 1‐3 Front view of DWG2004/DWG2008                                                              Figure 1‐4 DWG2001 

Notes: DWG2004 equips 4 antennas, DWG2008equips 8 antennas; both models have the same  appearance. 

DWG2001/DWG2004/DWG2008 serial supports GSM, CDMA network and frequency supported as  below: 

GSM: Support quad‐band 850/900/1800/1900MHz   

CDMA: Support 800MHz 

 

There are 3 models with DWG200X serial. Three models are shown in table 1‐1: 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Model                                  Network Type                                                Interface 

DWG2001                              GSM/CDMA                                  1WAN,1LAN ,1SIM channel         

DWG2004                              GSM/CDMA                                  1WAN,3LAN, 4SIM channels     

DWG2008                              GSM/CDMA                                  1WAN,3LAN, 8SIM channels     

Table 1‐1 DWG2001/DWG2004/DWG2008 interface description 

1.4 Functions and features 

1.4.1 Protocol standard supported: 

z Standard SIP and MGCP protocol;  z Simple Traversal of UDP over NATs (STUN);  z Point‐to‐point protocol over Ethernet (PPPOE);  z Hypertext Transfer Protocol (HTTP);  z Dynamic Host Configuration Protocol (DHCP);  z Domain Name System (DNS);  z GSM/CDMA;  z ITU‐T G.711α‐Law/μ‐Law、G.723.1、G.729AB; 

1.4.2 System function 

z PLC: Packet loss concealment  z VAD: Voice activity detection  z CNG: Comfort Noise Generation  z Local/Remote SIM card work mode  z Adjustable gain of port  z DTMF adjustment  z Balance alarm  z Lock/unlock SIM/UIM    z Mobile number display rejection  z Sending/receiving SMS  z Customize IVR Recording  z White and black list 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual  z One number access  z Open API for SMS, support USSD  z Echo Cancellation (with ITU‐T G.168/165 standard) z Automatic negotiate network  z Hotline 

1.4.3 Industrial Standards supported: 

z Stationary use environment: EN 300 019: Class 3.1    z Storage environment: EN 300 019: Class 1.2  z Transportation environment: EN 300 019: Class 2.3  z Acoustic noise: EN 300 753  z CE EMC directive 2004/108/EC  z EN55022: 2006+A1:2007  z EN61000‐3‐2: 2006,    z EN61000‐3‐3: 1995+A1: 2001+A2: 2005        z EN55024: 1998+A1: 2001+A2: 2003  z Certifications: FCC, CE 

 

1.4.4 General hardware specification 

  Power Supply: 

DWG2001: AC100~240V 50/60HZ DC12V/1A   

DWG2004/DWG2008: AC100~240V, 50/60HZ 

Temperature: 0~40  ℃  (Operation), ‐20~80  ℃(storage) 

Humidity: 5%~90%RH,   

Power Consumption: DWG2001: 5W, DWG2004/DWG2008: 30W 

Dimensions:   

DWG2001: 112(W) x76(D) x24(H) mm 

DWG2004/DWG2008: 440(W) 305(D) x44(H) mm 

Net weight: DWG2001: 0.7kg, DWG2004/DWG2008: 5.0kg 

1.5 Structure of product 

The appearance of A2001/DWG2004/DWG2008 serial shows in two views (front view and rear 

view).   

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

                       

Figure 1‐5 Front view of DWG2004/DWG2008                            Figure 1‐6 Front view of DWG2001  

1.5.1 Front view 

 

There is variety of indicators on front view of DWG2001/DWG2004/DWG2008, its names and  indications shown as table 1‐2:   

Indicators  Color  Name  Status  Description 

PWR  Green Power indicator 

Lighting    Power is on 

Off  Power failed 

RUN  Green  Running indicator 

Fast  Blinking  SIM cards Registered   

Slow blinking  Unregistered 

Occupancy  indicator of  channels 

Red 

Indicate that occupancy  status of channels 

Lighting   

Off   

Used   

Un‐used   

3 grids  Very strong   

Signal  indicator   

Green 

GSM/CDMA signal strength  indicator 

2 grids  Strong 

1 grid  Weak   

Table 1‐2 Description of indicators on front view of DWG2001/DWG2004/DWG2008  

Note: No signal strength indicator on DWG2001 

 

1.5.2 Rear view 

1) Description of interfaces on rear view of DWG2004/DWG2008 shows as below: 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

 

Figure 1‐7 Rear view of DWG2004/DWG2008 

 

2) Description of interfaces on rear view of DWG2001 shows as below: 

 

Figure 1‐8 Rear view of DWG2001 

 

1.6 Restore factory setting 

 

 

Push RST button for 6 seconds of DWG2001/DWG2004/DWG2008, the device will restore factory 

  setting.

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Chapter 2 Equipment installation

 

This chapter mainly introduces DWG2001/DWG2004/DWG2008 hardware installation and  connection of equipment. 

2.1 Installation notice 

DWG2004/DWG2008 used AC110~220V, 50/60Hz AC power supply, DWG2001 uses DC12V power. 

Power supply should ensure the reliability and stability; otherwise, it may damage the SIM card  or  device.  In  addition,  make  sure  the  power  supply  connects  to  ground  bar  well.  With  right  ground  protect  connection,  that  can  reduce  the  surge  voltage  caused  by  lightning  that  damage  the equipment, and ensure voice quality (note: when calls with irregular noise occurring, please  check the power whether connect ground well). Common measures are as follows: 

Making  sure  that  all  devices  powered  in  the  buildings  are  in  accordance  with  NEC  (National 

Electric Code, National Electrical Regulations) Article 250 of manual properly grounded; 

Making  sure  that  the  panel  of  building  power  supply  units  used  high‐quality  copper  wire  well  connect with the ground wire, copper wire specifications shall comply with NEC Table 250‐94/95  relevant provisions of the manual. Grounding cable that buried in the building field, including at  least one or several 2.44m deep under the ground, or buried deeply underground at least 0.76m,  with  a  wire  around  the  building  (see  NEC  manual  specifications  the  relevant  provisions  of  the  table 250‐94/95); 

Setting up voltage protector between equipment and ground connected to some other computer 

 

  equipments  (either directly or through other devices), such as terminal or printer must also be  plugged into the same surge protector.

   

Network  interface  of  DWG2001/DWG2004/DWG2008  supports  RJ45  standard  with  10Mbps  or 

100Mbps network.   

 

 

Wireless section, inserting SIM card directly, GSM channel should work properly.   

To check the network connection, user can monitor the registered status indicator (refer  Table 1‐2 ) 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

2.2 Installation procedure

The  outlook  of  DWG2001/DWG2004/DWG2008  looks  like  a  1U  chassis;  to  install  hardware  the  cable  is  needed.  After  unpacking  the  equipment,  please  do  follow  the  procedure  as  following  steps:

2.2.1 Install SIM card 

When installing SIM card, opening blank panel of SIM slot, procedure shows as below:   

 

 

 

 

 

 

 

 

 

2.2.2 Antenna installation 

Figure 2‐5 shows as below a compelete installation: 

Figure 2‐5 Antenna installation 

 

2.2.3 Cable connection of equipment 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

DWG2004/DWG2008 works in Bridge mode 

 

 

 

 

 

 

DWG2001 works in Route mode 

Figure 2‐7 DWG2001 connection   

2.3 Establishing remote access 

 

 

Figure 2‐8 Remote login environments 

After installation of DWG2001 /DWG2008, creating a remote access for technical support. 

10 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Chapter 3 Network configuration

 

In  this  chapter  we  will  introduce  the  initial  configuration  of  DWG2001/DWG2004/DWG200  gateway. All of the network parameters of the gateway can be configured by IVR guidance. 

3.1 Preparation 

Please ensure the following stepes are done properly before IVR setting:

1) Prepare an analog telephone or mobile phone   

2) Make sure the gateway is power on 

3) Make sure the gateway is connected with the network 

4) Completed the SIM installation 

5) Make sure that the current mobile network is working 

3.2 Attentions 

 

 

 

 

 

 

 

 

 

 

In  each  step,  if  user  hears  an  IVR  message  of  “setting  successful”,  which  means  that  user  has  finished  this  step  successfully.  However,  if  user  hears  a  “setting  failed”  message,  please  check  redo theatstep again. 

DWG2001/DWG2004/DWG2008 can work in two modes: route mode and bridge mode. when the 

 

  gateway is under bridging mode, user should configure network parameters of WAN port; when  the gateway is under the route mode, user should configure LAN port.   

11 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

3.3 General feature codes for system setting 

Dial numbers 

*114# 

*115# 

*150*a# 

*152*a*b*c*d# 

*153*a*b*c*d# 

*156*a*b*c*d# 

*158# 

*157 

*195# 

*198# 

*199# 

Features 

Play the phone NO. 

Check  the  TT  number  of  gateway  (using  just  when  the  device interconnects with other series of DINSTAR products) 

Set IP address(static/DHCP), a can be digit 1 or 2,*150*1# is  static IP address mode, *150*2# is DHCP mode 

Configure  IP  address,  a,  b,  c,  d  are  the  four  fields  of  IP  address. 

Configure  subnet  mask. a,  b, c,  d  are  the  four  fields  of  the  subnet mask 

Configure the device gateway, a, b, c, d are the four fields of  the device gateway 

Report the IP address 

Setting the work mode (route or bridge), * 157 * 0 # is route  mode, * 157 * 1 # is bridge mode 

Play record 

Clear record 

Setting Record. dial*199# start record(≤  20s), then press #  end the recording 

Restart device    *111# 

Table 3‐1 Feature codes for system setting 

3.4 Static IP Configuration 

This chapter introduces IP configuration of DWG2001/DWG2004/DWG2008 through calling IVR. 

Assuming  the  IP  address  of  a  DWG2001/DWG2004/DWG2008  device  is  172.16.0.100,  subnet  mask is 255.255.0.0, IP of gateway is 172.16.0.1, configured as follows: 

1) Insert a SIM card into the DWG2001/DWG2004/DWG2008 gateway 

2) The configuration mode: Dial the phone number of this SIM card. hear a message, then enter 

“*150*1#”, hang up when hear “ setting successful" message; 

3) Configure IP address: Dial the phone number of this SIM card, hear a message, enter "* 152 * 

12 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

172 * 16 * 0 * 100 #" hang up when hear    “setting successful" message; 

4) configure subnet mask: Dial the SIM card phone number, enter "*153*255*255*0*0#" hang  up when hear “setting successful" message; 

5) Configure gateway: Dial the SIM card phone number, enter "*156*172*16*0*1#" hang up  when hear “setting successful"    message; 

6) Please  wait  about  ten  seconds  when  finishing  the  operations,  restart  device.  dial  the  SIM  card phone number, enter “*158#”to check the Static IP address; 

 

3.5 DHCP configuration 

DHCP mode configure as follows: 

1) Insert an SIM in one of the port, Dial the SIM card phone number. When hearing a message,  then enter  “*150*1#”, hang up when hearing “ setting successful" message; 

 

 

 

 

 

 

 

 

 

 

2) Restart the device, wait for 30 seconds, and then dial the SIM card telephone number, enter 

"* 158 #" to query the IP address; 

Note: If reporting the IP address is 0.0.0.0, which means that the gateway could not obtain a IP  address successfully. Please check: 

1) Make sure the device have been connected to the network; 

2) Make sure the DHCP Server is working. If there is no DHCP Server, please set the IP of device  to static IP . 

13 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Chapter 4 WEB configuration

 

This charpter describes web configuration of DWG2001/DWG2004/DWG2008.   

4.1 Preparing   

WEB  configuration  includes  the  following  components:  network  configuration,  system  information, mobile configuration and system configuration. 

Dial “* 158 #” to get the IP address of the gateway, log on the web interface by a browser.   

4.2 Access the system through http 

Enter IP address of DWG2001/DWG2004/DWG2008 in browser, and the GUI shows as below: 

 

 

 

 

 

 

 

 

Figure 4‐2‐1 WEB log interface 

Enter  username  and  password  and  then  click  “OK”  in  configuration  interface.  The  default  username  and  password  are  “admin/admin”.  It  is  strongly  recommended,  change  the  default  password to a new password for system security. 

14 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

4.3 WEB configuration 

4.3.1 WEB Operation Guide 

DWG2001/DWG2004/DWG2008 WEB configuration interface consists of the navigation tree and  the detail configuration interfaces. 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 4‐3‐1 WEB introduce 

Go through navigation tree, user can check, view modify, and set the device configuration on the 

  right of configuration interface.   

 

15 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

4.4 System Information 

Figure 4‐3‐2 system information 

System  information  interface  shows  the  basic  information  of  status  information,  Mobile  information and SIP information. 

4.4.1 System information 

 

Figure 4‐3‐3 system information 

【MAC Address】Displays the current MAC of the gateway, for example: 00‐1F‐D6‐16‐O3‐7C; 

【Network  Mode】DWG2001/DWG2004/DWG2008  support  two  types  network  mode,  which  is    bridge and route modes; 

【Network】shows IP address and subnet mask. 

【DNS Server】Displays DNS server IP address in the same network with the gateway. 

【System Up Time】shows the time period of the device running. For example,:1h: 20m, 24s; 

16 

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

【Network Traffic Statistics】Calculates the netflow, including the total bytes of message received  and sent. 

【Version  information】shows  the  current  firmware  version,  for  example  EIA  AOS  9.50.16  PCB 

29.1 LOGIC 0 BIOS 1, Built on Sep 21 2010, 17:32:25; 

4.4.2 Mobile information 

Figure 4‐3‐4 mobile information 

Display GSM / CDMA channel and network status information, detailed shown as below: 

【Port】Numbers of ports of GSM/CDMA. 

【Type】Indicates the current type of network. Such as CDMA or GSM 

【IMSI】International Mobile Subscriber Identity, it is the uniquely identifies of SIM card. 

【Status】indicates the connection status of current GSM / CDMA module. 

【Remaining Call Duration】Limite a call duration to the SIM card, when call duration is out of  that duration, the call would be discontinued. This option shows remaining talk time. 

【Carrier】Displays the network carrier of current SIM card.

【Signal Quality】Displays the signal strength of in each channels of GSM / CDMA   

4.4.3 SIP Information   

 

 

 

Figure 4‐3‐5 SIP information 

Displays registration status information with Softswitch platform or SIP Server 

【Port】the corresponding number of GSM/CDMA channel, identify with 0‐9 figure 

【SIP User ID】SIP registration account of the Softswitch and SIP server provided 

【Registered】  Shows the registration status of VoIP channels, including 2 state of registered and  unregistered 

17 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

4.5 Network Configuration 

The navigation tree of the route mode and bridge mode as below:   

                     

Figure 4‐3‐6 bridge mode                                          Figure 4‐3‐7 route mode  

In the navigation tree of route mode, will have extra items of “MAC Clone”,”DHCP Server” ,”DMZ 

Host” ,”forward Rule”,”Static Route” . 

4.5.1 Local network 

Under the route mode, WAN port connects with ADSL modem, and LAN port connects with local  network. It will be used as a small switch when working in brigde mode. In this situation, user just  need to configure the WAN parameter and DNS. User also need configure the LAN port if working  in route mode. The web interface as bellows:

Figure 4‐3‐8 WEB interface of bridge mode 

18 

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

 

Figure 4‐3‐9 WEB interface of Route mode 

 

Detailed parameters describled as below: 

【Work mode】two options of route mode and bridge mode, default is bridge mode.  z Network Configuration 

【Link Speed & Duplex】the 5 options are “Auto Detect”,” 10Mbps/Half Duplex”,”10Mbps/Full 

Duplex”, “100Mbps/Half Duplex” and “100Mbps/Full Duplex”. Default is “Auto Detect” 

【Obtain  IP  Address  Automatically】enable  the  device  obtain  IP  Address  automatically  or  not. 

Default is enabling 

【Use  the  Following  IP  Address】configure  the  “IP  Address”,”  Subnet  Mask”  and  “Default 

Gateway” by manual 

【PPPoE】need ISP offer the account and password. Use this mode when have not router in the  local network.  z LAN port configuration 

This option works when “route mode” is selected. 

【Link Speed & Duplex】  the 5 options are “Auto Detect”,” 10Mbps/Half Duplex”,”10Mbps/Full 

Duplex”, “100Mbps/Half Duplex” and “100Mbps/Full Duplex”. Default is “Auto Detect” 

19 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

【IP Address】set IP address by manual configuring. Default is 192.168.1.1 

【Subnet Mask】set the lan port Subnet Mask by manual configuring, Default is 255.255.255.0  z DNS Server 

【Obtain DNS Server Address Automatically】When enable the WAN port option of “Obtain DNS 

Server Address Automatically” , which will be enabled subsequently. 

【Use the Following DNS Server Addresses】fill in the IP address of “Primary DNS Server” and 

“Secondary DNS Server” 

Note: all the options in this interface can take effect after restarting the device 

4.5.2 MAC Clone (configure this only when necessary) 

 

Figure4‐3‐10 Configuration of Mac Address Clone 

This function can prevent the device against blocking by the carriers. Enable this function on the 

“router  mode”,  the  device  can  be  anti‐blocked  when  the  carrier  to  limit  the  online  users  by  scanning the MAC address.   

4.5.3 DHCP Server 

Under  “route  mode”,  DWG  works  as  a  router.  Config  DHCP  serive  to  enable  the  DHCP  service  funcition of DWG, then DWG will works as a DHCP server. 

 

                                Figure 4‐3‐11 Configuration of DHCP service 

IP address Pool determines the range of IP addess of other devices in this network;   

IP Lease Time sets the duration for how long the IP works with the specific IP. If the duration is 

  out of the duration, the IP would be invalid; 

20 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

The  subnet  mask,  gateway, DNS  info  will  also  be  allocated  to  network  devices  automatically  by 

DHCP protocol. Generally,    there is no need to configure those items. 

NOTE:  Please  configure  the  start  and  end  IP  addressed  in  IP  address  pool,  subnet  mask  and  gateway  in  the  same network segment. Other devices in this network may not work when obtaining the IP address. 

4.5.4 DMZ Host (Option under “route mode”) 

In some conditions,    certain devices in LAN network need to do two‐way communication with 

WAN network( e.g. certain computer in LAN network need to provide multiple services to WAN  network). In this situation, Configure this device as the DMZ host. 

 

Figure 4‐3‐12 Configuration of DMZ Host 

4.5.5 Forward rules (Option under “route mode”) 

In some conditions, certain devices in LAN network need to provide channel communication with 

WAN network( e.g. certain computer in LAN network need to provide FTP service of channel 21  to WAN network). In this situation, Configuring forwarding rules to this device is necessary. 

 

Figure 4‐3‐13 Configuration of forwarding rules  

Service  channel  is  the  one  that  should  be  provided  to  WAN  network.  IP  address  is  the  one  of  devices  in  LAN  net  work.  The  device  needs  to  provide  services.  Protocol  is  the  service  protocol(TCP or UDP) 

The difference between forwarding rules and DMZ host is, DMZ host provides several consecutive  channels  and  communication  of  all  protocols,  while  forwarding  rules  provides  single  or  several 

21 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual  channels  communication  based  on  certain  protocol(TCP  or  UDP).  If  DMZ  host  and  forwarding  rules have conflicts,    will be determined by forwarding rules configurations. 

4.5.6 Static route(Option under “route mode”) 

Static route is the route rules in IP communication. Generally speaking, no need to config static  route. Configuring static route is necessary in such conditions: when several network segaments  exist  in  LAN  network  and  there’s  certain  application  between  these  network  segament.  Please  cancel “internet sharing” under “ Network configuration” first, then configure the “static route”. 

Figure 4‐3‐14 Configuration of Static route 

In  commly  use,  please  don’t  configure  static  route.  If  static  rule  is  wrong,  the  devices  may  not  work. 

 

4.6 Mobile configuration 

 

4.6.1 Basic configuration 

Figure 4‐3‐15 Basic Configuration 

 

 

 

Configuration details are as below: 

22 

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

【Dial Tone Gain(Mobile Side)】it is the dial tone volume of call waiting, dial tone of mobile  module when call out. Usually adopt the default configuration. 

【Select Band】according to carrier’s band standards. Standards are as belows: 

GSM:850/900/1800/1900 MHz ; CDMA:800 MHz; 

【Forward enable】enable the function of trunk call in for mobile phone user ID, that is, choosing  one  user  ID  of  the  SIM  channels  as  the access  No  of  DWG  device. When  several  calls  use  the  user  ID  at  the  same  time,  DWG  gateway  will  do  call  transfer  to  other  available  channels. 

Configuring the corresponding user ID in each channel is necessary. 

【Forward master mobile】select this channel’s mobile phone No. as the one access No. 

【Reject  Incoming  Calls】when  enable this  function, this  channel  can  only  be  used  to  call  out,  can’t used to call in. 

【Remote  API  Enable】  API  is  provided  for  third  party  development  with  DLL  and  IAD  components.  The  API  includes  SMS  sending  and  receiving,  USSD  sending  and  receiving.  The  default is “No” 

【API Server Address】it is the remote IP address who uses API. This is an option when selecting 

“Yes” under “remote API enable”. 

【API Server Port】it is the remote channel No. who uses API. This is an option when selecting 

“Yes” under “remote API enable”. 

4.6.2 Mobile 

23 

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Figure 4‐3‐16 Mobile Configuration 

Configuration details are as below 

【Mobile Number】SIM card user ID of the channel. That must be configured when “one access 

No.” funciton enable. 

【Enable Call Duration Limitation】this function is to limit the max call duration of channel. The  max call duration is between 1 to 65535 minutes. 

【Maximum Call Duration】defines a value by users. That will limit the SIM/UIM card’s total call  duration. After the call duration excesses this value, no call will be initiative by this channel. The  value range is 1‐65535. If user doesn’t configure this value, Default is no max call duration limits  for this channel. 

【Free time to call】a minimum charging time (in seconds) is defined during which no charging is  done  at  carrier  side.  If  the  conversation  time  is  even  shorter,  the  total  call  duration  will  not  decrease. 

【Mobile Number(Receiving Alarm)】  the mobile phone No. which used to receive the alarm 

SMS. Users can get SMS report of SIM/UIM card status(SIM Remain Time) in DWG. 

【Alarm Threshold(via SMS)】when the SIM remain time is or less than this value, DWG will send  the alarm SMS to remind the users of the SIM remain time. 

【Port  Description  for  Alarm】it  is  the  identification  mark  of  SIM/UIM  card  in  the  designated   

SMS  report.  The  mobile  phone  No.  of  the  SIM/UIM  card  is  recommended  to  use  as  the  port  description for alarm, or any other string. 

【SIM Remain Time】indicates the current sim remain time. It can’t modified. 

【Restore time】recovers the SIM remain time to initial value, the Maximum Call Duration. 

【CLIR】caller ID display restrict. This function is used to restrict the mobile phone No. By adding 

“#31” before the mobile phone ID, this funciton should be supported by carrier. 

【Mobile Tx Gain】transits gain of the mobile module, from IP side to PSTN side. 

【Mobile Rx Gain】receives gain of the mobile module,from PSTN side to IP side. 

【Detect  Reverse  Polarity】this  option  for  CMDA  Reverse  Polarity  detection.  Most  CDMA  operators  don't  offer  polarity  reverse  .  So  VoIP  to  mobile,  DWG2008  will  connect  soon.  It  doesn't wait mobile side answer. 

4.6.3 SIM/UIM card lock 

24 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Figure 4‐3‐17 Configuration of SIM/UIM Card Lock 

Configurations are as below: 

【Select Port】select the Channel No. which need to be locked. 

【SIM Card Lock】SIM card lock or unlock. Default is “No”. 

【PIN Code】correct PIN code is needed to lock or unlock the SIM card. 

4.6.4 PIN Management 

 

 

Figure 4‐3‐18 PIN Management 

 

Detailed description as below: 

【PIN management】PIN is the password of SIM card personal identification. In the status of 

SIM card locked, PIN can be modified to prevent SIM card from being stolen. 

【Select Port】selects the GSM/CDMA channel No. 

【Old PIN code】the previous PIN code 

【New PIN code】inputs a new PIN code 

【Confirm New PIN Code】inputs the new PIN code again. 

4.6.5 SMSC 

SMS  center  of  mobile,  theoretically,  the  celluar  modular  will  automatically  detect  the  SMSC  number. This configurable option is used in a situation that the SMSC number could not detected  by  celluar  modular.  When  such  case  happens,  please  contact  with  mobile  service  provider  to  identify the SMSC number and then add SMSC number in SMSC configurable web interface. 

25 

4.6.6 SMS 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

 

Figure 4‐3‐19 SMS sending 

Configurations are as below: 

【Select Port】users can select a defined channel or random channel to send SMS. Input the  recevier’s mobile phone No to send SMS. 

【Addressee】mobile phone No. of the receiver 

【Message】content of the SMS. The length is limited to 300 characters. 

 

4.6.7 USSD 

USSD  (Unstructured  Supplementary  Service  Data)  is  a  Global  System  for  Mobile(GSM)  communication technology that is used to send text between a mobile phone and an application  program in the network. Applications may include prepaid roaming or mobile chatting. USSD is  similar with Short Messaging Service (SMS), but unlike SMS. USSD transactions occur during the  session only. With SMS, messages can be sent to a mobile phone and stored for several days if  the phone is not activated or within range. 

 

26 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Notes:please check with local service provider before using this service. 

4.7 Routing configuration 

4.7.1 Routing parameter 

Globle parameters, it will take effect while number manipulation configured 

Route calls after manipulation: the parameters indicate that the gateway will select IP‐>Tel or 

Tel‐>IP routes after number manipulation completed. 

Route calls before manipulation: the parameters indicate that the gateway will select IP‐>Tel or 

 

Tel‐>IP routes before number manipulation completed. 

4.7.2 IP‐>Tel Routing 

 

27 

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

 

Function: 

When the softswitch/ sip server send the call traffic to gateway directly, must be added IP‐>Tel  routing.   

Parameter Description

 

Parameter  Parameter Description 

Index  It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. 

Description 

Source IP 

Source Prefix 

Destination Prefix 

Destination 

It describes the route for the ease of identification. Its value is character string 

It specifies the source IP which will send the calls to gateway  y Any: any IP address   y IP: specific an IP address   y IP Group: specific an IP group  

All the caller number must match the source prefix. It specifies the source prefix  allow to send call out  y Any: include anonymous, 0xxxx, 1[2‐9]xxxx etc.

  y 0xxxx: consist of some digits such as 015,08,09  y 1[3‐8]6:consist of some prefix, include 136,146,156,166,176, 186 

All the called number must match the destination prefix, the call prefix indicates  the connected number  y Any: include anonymous, 0xxxx, 1[2‐9]xxxx etc.

  y 0xxxx: consist of some digits such as 015,08,09 

1[3‐8]6:consist of some prefix, include 136,146,156,166,176, 186 

Its specifies destination Port or Port Group 

Example: 

Index 0 : add a route from VoIP to GSM, the calls coming from IP Group 18<asterisk> will call  out thourgh destination Port Group 31<Unicom>.   

28 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

 

The caller party coming from IP Group 18 will match source prefix ”any”, ”any” is a wildcard string  include anonymous calls. At same time, destination prefix must match with ” 

13[4‐9]xxxxxxxx|6xxx|10086”. 

Index 1: add a route from VoIP to GSM, the calls coming from IP 14<tribox> will call out  through destination Port Group 31<Unicom> 

   

The caller party coming from IP 14 will match source prefix ”any”, ”any” is a wildcard string which  will match prefix anonymous calls. At the same time, destination prefix must match with ” 

 

15[0189]xxxxxxxx|188xxxxxxxx”. 

Index 2: add a VoIP to GSM route which allowed all the calls. It will receive all calls coming from  any IP to destination Port Group 31 

29 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Prefix ”any” is a wildcard string which will match anonymous calls as well. 

4.7.3 Tel‐>IP Routing 

 

 

Function: 

This item uses to configure incoming call routes which can be used for recieve the calls from the 

GSM. 

Parameter Description

 

Parameter  Parameter Description 

Index  It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. 

Description  It describes the route for the ease of identification. Its value is character string 

Source Port  It specifies the Port or Port Group which will receive the calls from PLMN 

Source Prefix 

All the caller number must match the source prefix. It specifies the source prefix  allow to send call out  y Any: include anonymous, 0xxxx, 1[2‐9]xxxx etc.

  y 0xxxx: consist of some digits such as 015,08,09  y 1[3‐8]6:consist of some prefix, include 136,146,156,166,176, 186 

Destination Prefix  All the called number must match the destination prefix, the call prefix indicates 

30 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Destination  the connected number  y Any: include anonymous, 0xxxx, 1[2‐9]xxxx etc.

  y 0xxxx: consist of some digits such as 015,08,09 

1[3‐8]6:consist of some prefix, include 136,146,156,166,176, 186 

Its specifies destination Port or Port Group 

 

Example: 

Index 0: its a default route configured in gateway 

It allows any number from source port 0 send call to SIP server with any prefix. 

Index 30: add a GSM to VoIP route   

 

It indicates that the calls coming from Port Group 31<Unicom> will match the prefix ”x.”, ”x.” is a  wildcard string which will match any prefix except ”anonymous” calls. Meanwhile sending the  calls destination IP 13<eia> if called number match with destination prefix ”00”. 

 

31 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

 

Index 31: add GSM to GSM route,its mainly used for saving the cost between two carriers 

It indecates that calls coming from Port 0 will match the prefix 13[58], ”13[58]” include prefix 135 

  and 138, caller number can’t match prefix 135 and 138 will reject by gateway. Meanwhile sending  the calls to Port Group 31<Unicom> if called number match with prefix 133.   

 

4.8 Manipulaton Configuration 

 

Function 

It is an optional configuration item, and is used to add IP‐>Tel number change data. 

The IP‐>Tel Manipulation defined the rules of add, and deletion of called numbers, which are  referenced by IP‐>Tel routing.   

Parameter Description 

Parameter  Parameter Description 

Index  It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. 

32 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Description  It describes the route for the ease of identification. Its value is character string 

Source IP 

Source Prefix 

Destination Prefix 

It specifies the source IP which will send the calls to gateway  y Any: any IP address   y IP: specific an IP address   y IP Group: specific an IP group  

All the caller number must match the source prefix. It specifies the source prefix  allow to send call out  y Any: include anonymous, 0xxxx, 1[2‐9]xxxx etc.

  y 0xxxx: consist of some digits such as 015,08,09  y 1[3‐8]6:consist of some prefix, include 136,146,156,166,176, 186 

All the called number must match the destination prefix, the call prefix indicates  the connected number  y Any: include anonymous, 0xxxx, 1[2‐9]xxxx etc.

  y 0xxxx: consist of some digits such as 015,08,09 

1[3‐8]6:consist of some prefix, include 136,146,156,166,176, 186 

Its specifies destination Port or Port Group  Destination 

Stripped  Digits  from 

Left 

Stripped  Digits  from 

Right 

Prefix to Add 

Suffix to Add 

It specifies the length of the digits to be deleted from left 

It specifies the length of the digits to be deleted from right 

Add the new digits in front of the original number 

Add the new digits at the end of the original number 

Example 

Add an IP‐>Tel Manipulation, to change the called number from 2547888888 to 07888888 

It indecates that calls coming from IP Group will match the prefix ”any”, and the called nubmer 

33 

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual  whom match with the prefix ”2547” will delete 3 digits in front of it and replace it by digit ”0”. 

4.9 Operation 

 

 

Function 

It is an optional configuration item. Operation configuration essentially involves allow, barring  some IP and IP Group send calls to certain numbers. It includes: forbid call, call allowance, auto  call, and password authentication . 

Parameter Description 

Parameter  Parameter Description 

Index 

Source IP 

Source Prefix 

Destination Prefix 

Operation 

Description 

It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. 

It specifies the source IP which will send the calls to gateway  y Any: any IP address   y IP: specific an IP address   y IP Group: specific an IP group  

All the caller number must match the source prefix. It specifies the source prefix  allow to send call out  y Any: include anonymous, 0xxxx, 1[2‐9]xxxx etc.

  y 0xxxx: consist of some digits such as 015,08,09  y 1[3‐8]6:consist of some prefix, include 136,146,156,166,176, 186 

All the called number must match the destination prefix, the call prefix indicates  the connected number  y Any: include anonymous, 0xxxx, 1[2‐9]xxxx etc.

  y 0xxxx: consist of some digits such as 015,08,09 

1[3‐8]6:consist of some prefix, include 136,146,156,166,176, 186 

Its specifies number analysis rule  y Forbid call   y Allow call   y Auto call   y Password authenticate  

It describes the route for the ease of identification. Its value is character string  

34 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Example   

Index 31: barring the certain calling number from IP 14<elastix>   

It indicates that calling party from IP 14<elastix> matched prefix 2877, and also called party  matched prefix 07 are not allowed call out. The calls match this rule will be rejected by gateway. 

Index 29: definite a rule for IP 17<FreeSentral> that all the calls must go with valid password  authentication.   

 

4.3.8 Port Group Configuration 

35 

 

 

 

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Function 

This configuration step is necessary, and is used to add port group in gateway. The port group will  referenced by IP‐>Tel routing and number manipulation. 

Parameter Description 

Parameter  Parameter Description 

Index  It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. 

Description  It describes the route for the ease of identification. Its value is character string 

Port 

Select Mode 

It specifies the Port will add to port group 

It specifies the policy for selecting port in a port group  y Ascending:  the  system  always  selects  a  port  from  the  minimum  number.  The  preferential selection of the port can be realized through this mode   y Cyclic  ascending:  when  system  selects  ports’  Priority,  it  always  begin  from the  number next to the number selected last time, if the maximum priority number  is  selected  last  time,  then  the  next  number  is  the  minimum  priority  number,  and move in cycles like this   y Descending: when system selects ports’ priority, it always begin to select from  the maximum priority number   y Cyclic descending:   when system selects ports’ Priority, it always begin from  the  number  before  to  the  number  selected  last  time,  if  the  minimum  priority number is selected last time, then the next number is the maximum  priority number, and move in cycles like this 

Example 

To add a port group, assume that port 6, port 7 belong to the same carrier, add port 6 and port 7  to port group 30, select mode is cyclic ascending. 

 

36 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

4.3.9 IP Group Configuration 

1) IP configuration 

 

Function 

Add remote IP of Softswitch, SIP server which will send call traffics to gateway. 

Parameter Description 

Parameter  Parameter Description 

Index  It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. 

Description 

IP 

Port 

It describes the route for the ease of identification. Its value is character string 

It  is  an  interworking  parameter  between  the  remote  Softswitch  and  the  SIP  server. It specifies the IP address of the peer equipment. 

It  is  an  interworking  parameter  between  the  remote  Softswitch  and  the  SIP  server.

 It specifies the SIP port number of the peer equipment 

Example 

To add a remote IP of Softswitch, set “index” to “31”, SIP port number “5060” 

 

2) IP Group 

37 

 

 

 

 

 

 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

 

Function 

This configuration is optional, and is used to add the IP that have the same attributes to an IP  group. The IP group will referenced by IP‐>Tel routing and number manipulation. 

Parameter description 

Parameter  Parameter Description 

Index  It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. 

Description 

IP 

It describes the route for the ease of identification. Its value is character string 

It specifies the IP will add to IP group 

 

Example   

To add an IP group, set IP “10, 14, 17” to IP group 18 

 

38 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

1) System configuration 

Figure 4‐3‐20 System Configuration 

Configuration details as below: 

【Voice Prompt Language】configure the voice prompt of DWG., e.g.    configure voice prompt of 

IP  address  success  or  failure.  DWG  supports  English  and  Chinese.  Users  can  customize  other  languages. The default setting is in Chinese.  z Provision configuration 

Provision is used to maintain the devices. E.g. Provision can config, update and remote manage  the devices in bulk. 

【Primary Provision Server IP】this is provided by carrier. Keep the default value if carrier don’t  provide this value. 

【Primary Provision Server Port】this is provided by carrier. Default is 80. 

【Secondary Provision Server IP】this is provided by carrier. Keep the default value if carrier don’t  provide this value. 

【Secondary Provision Server Port】this is provided by carrier. Default is 80. 

【Provision Check Interval】default is 4 hours.  z NTP Configuration   

【Enable NTP】NTP enable switch 

【Primary NTP Server IP】can keep the default   

【Secondary Provision NTP Server IP】can keep the default   

【Time Zone】the default is GMT +8:00, the user can adjusted accordingly according to their area 

39 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

2) Service configuration (for SIP only) 

Service Configuration is used for configuring voice calls and some small businesses, such as Call 

Progress Tone, codec, silence suppression, * service, the second dial and so on   

 

Figure 4‐3‐21 Service Configuration 

Detailed description as follow: 

【LOCAL  RTP  PORT  Channel】means  the  initial  allocation  of  Channel  when  RTP  voice  stream  transmit in the IP network , in general, using the factory default values. When there are multiple 

DINSTAR series voice products, and the network gateway or router’s NAT with loopholes, user  can try changing this item. 

【Enable Silence Suppression】enable the "silence suppression" almost no impact on call quality,  and can save about half of the bandwidth. 

40 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

【Call Progress Tone】each country has its different call progress tone required standards, such as  busy  tone,  ring  back  tones  and  ring  tone  standards,  users  can  select  the  area  standard  from  here . 

【Preferred Coders】means the code format when Voice transfer on IP network, support PCMA, 

PCMU, G.723.1 andG.729AB. 

Note:  when  the  preferred  codec  switch  between  G.723.1  and  G.729AB  ,  System  will  automatically reset 

【Enable  PSTN  Incoming  Configuration】  means  when  call  from  PSTN  side,  you  can  dial  the  function keys for check number, setting IP and so on function   

【Enable Auto Outgoing Routing  】means when call out , whether by ordinal or polling pick to 

Select a Channel, this feature are generally used for when use the same SIP User ID to register  or use as trunking mode 

【IP to PSTN One Stage Dialing  】  this function will be displayed only when select "Enable Auto 

Outgoing Routing" function, the User ID will be sent directly to PSTN, for example: the user calls 

6715, the device will sent 6715 User ID to PSTN 

【Play Voice Prompt for PSTN Incoming Calls  】setting is yes, when through the PSTN calls to the 

Channel, the device will with the clew tone, the default is "Please dial the extension User ID";  setting to No, the device will with dial tone 

【Send  Original  Caller  ID  for  PSTN  Incoming】for  Example,  the  phone  A  from  PSTN  side  call 

DWG2001/DWG2004/DWG2008 Channel SIM card corresponding User ID, the Channel's SIP User 

ID is C, Channel hook and then call B,    when "Send Original Caller ID for PSTN Incoming" setting  is  Yes,  the  Caller  User  ID  that  send  to  B  will  be  A,  when  "Send  Original  Caller  ID  for  PSTN 

Incoming"  setting  is  No,  the  caller  User  ID  that  sent  to  B  will  be  C(except  for  anonymous  outgoing ) 

【 DTMF 】 DWG2001/DWG2004/DWG2008  support  RFC2833  and  SIGNAL  two  ways.  DTMF 

INTERVAL range is 50 ~ 800ms, DTMF VOLUME can use the default Configuration 

【Enable  STUN】(Simple  Traversal  of  UDP  over  NATs,NAT’s  UDP  simple  cross)  is  a  network  protocol.  It  is  allowed  to  stay  behind  the  NAT  (or  multiple  NAT)  client  part  to  identify  their  clients’ public address, found himself after what Type of NAT and NAT for a particular Channel is  bound to a local Internet terminal Channel. This information is used for two host to set up UDP  communication behind the same NAT router. The agreement defined by the RFC 3489 

41 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

【CLID Mode】Select the name under the special needs , the most common way is use the default 

User ID   

 

【Other Configuration】: 

Enable”*“at  the  beginning  private  internal  service:  the  default  is  enable,  that  the  private  internal  network‐related  service  refer  to  Configuration  query,  recording,  adjust  the  volume,  restore the factory default values, etc. ; 

SIP  request  message  whether  with  a  user  =  phone:  is  a  SIP  protocol  requirement,  if  the  soft  switch no require, setting is no; 

Only Accept Calls from SIP Server: is whether only accept the call from the SIP PROXY Server , if  the setting is Yes, the call through point to point IP ADDRESS will be rejected (not launched from 

SIP server's address) ; 

  “Allow Outgoing Calls without Registration”and “Allow Incoming Calls without Registration”need  use together , which refer to "SIP Configuration" ‐ "Is register" option, if”Is register" setting is  no,    this two options need set Yes ,to avoid that the devices can not call out ; 

  “Allow Anonymous Outgoing Calls” setting to No, the device caller User ID is a registered User ID,  setting to Yes, the device Caller User ID as "Anonymous" ; 

"Allow Anonymous Inbound" setting to No, the incoming anonymous calls will be rejected; 

  “Use # as End Key”,in General, SIP phones are based on # as the end, if this option is set to No,  the dial‐up will end expires dial‐up time; 

  “Inter digit Timeout”Bit of between the dialing time ,over the time will be seem as end of  dial‐up; 

【NOTE】close* Business functions , not mean the related business can not be used, users can 

 

 

 

 

 

  also through web Configuration the corresponding function 

42 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

3) SIP Configuration (for SIP only) 

Figure 4‐3‐22 SIP Configuration  

SIP Configuration: used for Configuring VoIP channel, add SIP Registry Platform and local SIP 

Channel, and configure SIP protocol and other related information 

Detailed description as follow:  z SIP PROXY 

【SIP Server Address】use for configure SIP server address and Channel, the address can be IP 

Address, also can be a domain name (DNS should to be able to resolution), the details please  advisory the service provider 

【SIP Proxy Port】port default setting is 5060. For details, please consult the service provider  z Outbound Proxy 

【Outbound Proxy Address】Outbound proxy, it mainly used in firewall / NAT environment. That  make  the  signaling  and  media  streams  are  able  to  penetrate  the  firewall,  the  details  please  advisory the service provider   

【Outbound  Proxy  Port】outbound  proxy  port  number,  the  details  please  advisory  the  service  provider 

【Use Random Port】set the local monitor SIP port(fixed or random), random is every time you  start the device will random Select a free SIP port Monitor 

【Is Register】  default set yes, if you want the device can make a call without register, set No, 

Also enable the "Allow Outgoing Calls without Registration" and "Allow Incoming Calls without 

Registration" function   

43 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

【Register Interval】means how often the equipment will register once to the SIP server/proxy 

【T1】  used to define the SIP protocol T1 timer value, default is 500ms; 

【T2】  used to defines the SIP protocol timer values, default value is 4000ms; 

【T3】used to define the T2 timer value in SIP protocol, the default is 5000ms; 

【Keep alive Interval】used for keep communicate between equipment and the SIP server that  make the device is in the best available Registered. In general, using the factory default values 

 

Note: all parameters refering to defaultt setting of SIP protocol, user can modify that if necessary   

4) Port configuration 

Port Configuration is used to configure ports’ gain, Off‐hook Auto‐Dial, etc.

Figure 4‐3‐22 Port Configuration  

Interface describe as following: 

【ALL ports register used same user ID】  The default is not, each SIP account, if set yes ,all the  port will use user ID of port0, when the call ring in sequence   

【SIP  User  ID】is  the  account  used  for  registration,  equipment  port's  unique  identifier, 

"Authenticate  ID"  is  equivalent  to  show  the  name,  "Password"  is  register  Password,  which  no  passward can no fill, the details please contact the service provider   

【Tx Gain】refers to the call volume that from himself during a call to the end users, adjust the "Tx 

Gain" will affect the voice volume of the end user, the default value is 0 

【Rx Gain】refer to the call volume from the remote end user to ourself volume, adjust the "gain  acceptance" will affect the voice volume we will heard, the default value is 0. 

【Offhook Auto‐Dial】Hotline service.when PSTN part client calls to this port,will auto forward to 

44 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

 

 

 

 

  the hotline User ID. If no need this feature, just left it blank 

【Auto‐Dial Delay Time】Offhook Auto‐Dial delay time, the range is 0‐10 seconds 

5) Fax Configuration 

Figure 4‐3‐23 Fax Configuration  

Fax  Configuration  use  for  configure  fax,  and  support  pass‐Through  and  T.38  fax  mode,  the  maximum baud rate supported 14400bps 

Interface describe as following: 

【Fax way】support T.38 and pass‐Through; 

【Fax Tone Detection Mode】There are two calling and called 

【Enable ECM】Error Correction Mode. If enabled, when transmiss the fax ,will automatically  detects the wrong part of the requested retransmission to eliminate data errors, but will  increase the fax time   

【Fax Rate】support fax rate list include:2400bps、4800 bps、7200 bps、9600 bps、12000 bps、

14400 bps 

4.3.6 Tools   

1) Firmware upload 

Equipment upgrades can through Dinstar’s softswitch platform, when the device disconnects with 

Dinstar’s  softswitch  platform  or  some  special  circumstances.  The  firmware  is  able  to  upload  locally. 

45 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

  Figure 4‐3‐24 firmware upload  

Select the upgrade program under correct directory services, and then click upload will complete  upgrade the firmware. 

NOTE:  during  the  upgrade  process,  please  do  not  swtich  off  the  power  supply,  equipment  may  paralyze. 

2) IVR Voice Prompt Upload 

By default, when PSTN call incoming, the system will play the default IVR, and also the user can  load custom IVR. 

Figure 4‐3‐25 IVR Voice Prompt Upload  

 

 

 

 

 

 

 

NOTE: the customize voice files can be recorded using Windows recording programs, the sound  format is 8000Hz, 16 bit sampling in mono, with WAV format, size of files can not exceed 190KB 

46 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

3) Login password 

Figure 4‐3‐25 IVR Voice Prompt Upload  

When using web or telnet Configuration, please enter default user name and password. User can  modify the login name and password. 

4) Factory Reset 

Figure 4‐3‐26 Factory Reset 

Be careful do this operation, after restore factory setting, all the parameters will be changed to 

  the factory default. 

6) Restart 

Figure 4‐3‐27 Restart 

 

 

 

When system restarts, user click RESET button on the web. 

47 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Chapter 5 FAQ

  z Device have been connected to network physically, but the network cannot be connected or  network communication is not normal 

1) Make sure the network cable is ok or not , can through view the device WAN port or LAN  port indicator light to determine the physical connection is working or not; 

2)  Make  sure  the  connected  network  devices  (router,  switch  or  hub)  support  10M/100M  adaptive,  if  not,  connect  the  Equipment  directly  to  PC,  landing  WEB  and  in  the  "local  connection" Configuration interface Select the correct Ethernet Work Mode; 

3) Check the Network Configuration, if the Configuration is incorrect, please re‐Configuration. 

If you are using DHCP mode, check DHCP Server is working properly; 

4) Check whether there is a LAN device conflict with the exists IP ADDRESS;  z Equipment cannot register 

 

 

If the Run LED does not flash mean unregistered 

1) Check the network connection is working (see above section), whether the Configuration  is correct; 

2) Check whether the LAN firewall setting is inappropriate (such whether limit the network  communication); If it is, there are two ways to try to resolve; 

3)  Ask  network  administrators  to  open  limitation  with  the  equipment’s  network  communications  (it  is  a  special  equipment,  not afraid  of  virus  attacks);  (2)  try to  enable  the equipment tunnel (through the WEB for Configuration, Also, please NOTE, open the  tunnel  will  impact  voice  quality,  Please  do  not  enable  the  tunnel  as  far  as  possible,  reference WEB Configuration Interface Description section); 

4)  Check  whether  the  Local  Network  to  the  SIP  PROXY  platform  network  environment  is  relatively  poor  or  not,  and  if  so,  please  check  Local  Network  or  contact  the  service  provider; 

5)  if  go  through  those  steps,  the  device  still  be  in  trouble,  please  contact  the  equipment  provider; 

48 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual  z When calling out, the callee’s phone shows wrong caller ID:   

1) Ask the callee checks whether the device is failure or device battery power is low 

2) Make sure the callee has been subscribed called User ID display service 

3)  If  only  part  of  the  caller  User  ID  with  this  problem,  please  contact  the  Telecom  Carrier  to  identify the problem.

  z when calling in, the caller always hears a busy tone 

Make sure Enable DND(Do‐not‐Disturb) in system  z sudden interruption during a call 

1) make sure whether is human error caused the problem 

2) Make sure with the account balance or lack of disruption caused the call disconnected 

3) Make sure whether there is interference with the fax tone or equipment busy tone, these  interference may lead to calls dropped 

4)  Make  sure  whether  the  LAN  equipment  such  as  gateway  or  router  fails,  user  can  try  to  restart the gateway or router  z voice single‐pass, double‐barrier or poor quality   

1) Make sure the equipment is working properly with grounded power 

2) Check the device network connection is in working status 

3)  Ask  network  administrators  to  open  limitation  with  the  equipment’s  network  communications (it is a special equipment, not afraid of virus attacks); (2) try to enable the  equipment  tunnel    (through  the  WEB  for  Configuration,  Also,  please  NOTE,  open  the  tunnel  will  impact  voice  quality,  Please  do  not  enable  the  tunnel  as  far  as  possible,  refer 

WEB Configuration Interface Description section) 

4) Make sure the LAN equipment is working, user can try to restart the gateway or router to  solve the problem 

5)  Check  whether  there  is  more  than  one  DINSTAR  series  products  in  LAN  network:  some  gateways  or  routers,  processing  network  packet  is  vulnerable  (for  example,  to  multiple  network  devices  or  the  same  protocol  network  communication,  NAT  allocated  the  same  conversion  communications  Channel).  If  there  is  such  a  case,  suggest  replacing  a  router  or  specify each voice gateway with different LOCAL RTP PORT Channel (refer to the base WEB 

49 

                                                                      DWG Series GSM/CDMA VoIP Gateway User Manual 

Configuration interface section) 

6) Check the equipment network environment for the softswitch platform, monitor the  network condiation, make sure the network is solid 

 

Glossary 

GSM: Global System for Mobile Communications 

CDMA: Code Division Multiple Access 

FMC: Fixed Mobile Convergence 

SIP: Session Initiation Protocol 

MGCP: Media Gateway Control Protocol 

DTMF: Dual Tone Multi Frequency 

USSD: Unstructured Supplementary Service Data 

PSTN:Public Switched Telephone Network 

STUN: Simple Traversal of UDP over NAT 

 

IVR: Interactive Voice Response 

IMSI: International Mobile Subscriber Identification Number 

IMEI: International Mobile Equipment Identity 

DMZ: Demilitarized Zone 

50 

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement