D-Link | DES-3010PA-TAA - Switch 8-PT 10/100MBPS Poe Mgt | Specifications | D-Link DES-3010PA-TAA - Switch 8-PT 10/100MBPS Poe Mgt Specifications

ACCESS CONTROL SYSTEM GENERAL BUILDER
DEVICE/MODULE EXAMPLES
This document provides some sample devices utilized in an “Access Control Building System”.
Enable the “Display Bookmarks” feature of your PDF viewing application (varies with application used)
to browse the different device categories or “Module Classes” to assist you in identifying which devices
you would like to document with g-VIEW
LAYNE TECH-DESIGN
info@laynetech.net (925) 354-1527
Intelligent System Controller
LNL-2000
The LNL-2000 Intelligent System Controller (ISC) from Lenel is designed for advanced access
control applications. As the access control engine for the OnGuard system, the ISC provides
power and functionality. The ISC can communicate to the host computer in a single- or dual-path
configuration of Ethernet, dial-up or direct connect communication (RS-232/RS-485 combinations).
Multiple combinations of Input Control Modules, Output Control Modules, Biometric Gateways, and
Card Reader Interface Modules (up to 32 devices, 64 readers) can be configured.
Access Control
The LNL-2000 can communicate upstream to the host computer at up to 115.2 Kbps via RS-232,
RS-485 multidropped, dial-up, or Ethernet communication. The LNL-2000 can store up to 350,000
cardholders online, and supports selective download for larger cardholder databases. The ISC has
two host communication ports. It also has four downstream communication ports, which support
either four 2-wire or two 4-wire RS-485 communication. In either configuration, you may connect
up to 32 devices in many combinations of LNL-1100, LNL-1200,LNL-1300, LNL-1320, LNL-500B,
and LNL-500W modules.
Features and Functionality
■ Host dual path communication enabled - direct wire (RS-232/RS-485 multi-dropped), Ethernet
TCP/IP, or dial-up communications
■ 1 MB on board memory expandable to 8 MB (up to 350,000 cardholders)
■ 12 VAC or 12 VDC input power
■ Supports up to 16 different formats (8 card formats and 8 asset formats)
■ Biometric template storage support for RSI®, Identix®, and Bioscrypt®
■ Enhanced anti-passback capabilities
■ Flash memory for real-time program updates
■ Lithium battery back-up for event memory
■ Up to 32,000 access level permissions
■ 255 holidays with grouping
■ 255 timezones, each with 6 intervals
■ Elevator control support for up to 128 floors
■ Alarm masking
■ Individual extended held open and strike times (ADA required)
■ Up to 9-digit user PIN codes
■ Status LEDs for heartbeat, upstream and downstream communication
■ Two dedicated inputs for tamper and power failure status
■ NIST Certified Advanced Encryption Standard (AES) 128-bit algorithm for communications
5
LNL-2000
OnGuard
Security
Server
Up to 8 Biometric Devices
LNL-1300
LNL-500B
Up to 32 Downstream Devices
(64 Readers Max)
LOCAL AREA NETWORK (TCP/IP)
LNL-2000
Intelligent
System
Controller
LNL-1300
Up to 32 Single Reader
Interface Modules
RS-485 multidrop
Downstream
Communication
Four 2-wire ports
Two 4-wire ports
Combination 2- and 4-wire ports
LNL-1320
Up to 32 Dual Reader
Interface Modules
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
Access Control
CORPORATE HEADQUARTERS
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Hand Geometry or Fingerprint
Readers
Readers
Controller Options
LNL-2000
Memory Options
LNL-1003MK
LNL-1007MK
Host Communications
LNL-ETHLAN
LNL-ETHLAN-MICR
Dial-Up Modem
LNL-56KEXT
LNL-DC336K
Standard 1 MB on-board memory
3 MB memory expansion kit (Includes 3 MB memory and expansion board)
7 MB memory expansion kit (Includes 7 MB memory and expansion board)
Micro serial server, flash ROM, DB25 serial port RJ-45 (10/100Base-T)
CoBox Micro serial server, flash ROM, RJ-45 (10/100Base-T), diagnostic LEDs,
dimensions 1.6 x 1.9 in. (40 x 49 mm), internally powered and includes standoffs
56 K external Modem with cables
12 VDC-powered/33.6 K external modem for Intelligent System Controller
Specifications
Primary Power (DC or AC)
DC input:
AC input:
Memory and Clock Backup
Communication Ports
Port 1, 6:
Ports 2-5:
Inputs
Cabinet Tamper Monitor:
Power Fault Monitor:
Wire Requirements
Power:
RS-485:
RS-232:
Inputs:
Environmental
Temperature:
Humidity:
Mechanical
Dimensions:
Weight:
Approvals
* The ISC is for use in low voltage, power-limited, class 2 circuits only.
12 VDC ± 15%. 400 mA
12 VAC ± 15%. 650 mA RMS
3 V lithium, type BR2325
RS-232 or RS-485 (2-wire or 4-wire) 9600 to 115.2 Kbps async
RS-485 (2-wire or 4-wire) 9600 to 38.4K bps async
Unsupervised, dedicated
Unsupervised, dedicated
1 twisted pair, 18 AWG
24 AWG twisted pair(s) with shield, 4000 ft. (1219 m) maximum
24 AWG, 25 ft. (7.6 m) maximum
Twisted pair, 30 ohms maximum
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)
10 oz. (290 g) nominal
UL 294 and 1076-listed, CE-marked, RoHS compliant
NIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
6
Dual Reader Interface Module
LNL-1320 Series 2
Lenel Systems International offers a Dual Reader Interface (DRI) module for access control
solutions. Most access control card readers, keypads, or readers with keypads that use standard
Wiegand Data1/Data0 or Clock/Data communication are supported, as are those that support the
bidirectional RS-485 Open Supervised Device Protocol (OSDP). Lock, unlock, and facility code
offline access modes are supported on all readers connected to the DRI. Each DRI supports up to
eight different card formats as well as issue codes for both magnetic and Wiegand card formats.
Access Control
The DRI provides a vital link between the Intelligent System Controller (ISC) and the card reader
attached to the interface. As many as 32 DRI modules can be multidropped using RS-485 2-wire
or 4-wire communication up to 4,000 feet per port away from the ISC. Each DRI module is
individually addressed for increased reporting capabilities with OnGuard access control software
applications. The DRI includes eight inputs that support normally open, normally closed,
supervised, and non-supervised circuits. In addition, six output relays support fail-safe or
fail-secure operation.
Features and Functionality
■ 12 or 24 VDC power supply
■ Supports Data1/Data0, Clock/Data and Lenel OSDP-compatible RS-485 readers and keypads
■ Downloadable firmware
■ Six Form-C 5 A at 30 VDC relay outputs
■ Up to 16 different formats (8 card formats and 8 asset formats)
■ Issue code support for magnetic and Wiegand formats
■ Door contact supervision (open/closed)
■ REX push-button monitor
■ Strike control output
■ Bicolor reader status LED support and 2-wire LED support
■ Beeper control
■ Dedicated tamper and power failure circuits
■ Support for offline reader access mode
■ On-board jumpers for termination
■ On-board regulator allows 12 VDC reader support from 24 VDC power source
■ DIP switch-selectable addressing
13
LNL-1320 Series 2
OnGuard
Security
Server
CORPORATE HEADQUARTERS
LOCAL AREA NETWORK (TCP/IP)
Intelligent
System
Controller
LNL-1300
Single Reader
Interface Module
LNL-1320
Dual Reader
Interface Module
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Access Control
RS-485 multidrop
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current
with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery
optional), UL-listed
Lenel UL Listed Power Supply - 12 or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply current
with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery
optional), UL-listed
Battery kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC)
DC input:
Reader Power
DC output:
Reader Port Compatibility
Environmental
Temperature:
Humidity:
Mechanical
Dimension:
Weight:
Approvals
* The DRI is for use in low voltage, power-limited, class 2 circuits only.
12 or 24 VDC ± 15%. 450 mA
12 VDC, 125 mA regulated or 12 to 24 VDC 125 mA current limited
Wiegand Data1/Data0
Magnetic Clock/Data
F/2F single-wire protocol
Open Supervised Device Protocol (RS-485)
Operating: 0° to +70° C (32° to 158° F)
Storage: -55° to +85° C (-67° to 185° F)
0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)
10 oz. (290 g) nominal
UL 294 and 1076-listed, CE-marked, ROHS compliant
14
Input Control Module
LNL-1100 Series 2
The Lenel Input Control Module (ICM) provides the access control system with high-speed
acknowledgment of critical alarm points in monitored areas. The ICM communicates directly with
the Intelligent System Controller (ISC) either by 2-wire or 4-wire RS-485 communication. The ICM
has 16 configurable input control points and 2 output control relays. It supports normally open,
normally closed, supervised and non-supervised circuits.
The input circuits are scanned using an analog-to-digital converter. The digitized input status
Access Control
signal is software-monitored and controlled, so that each input point can be programmed as a
supervised or non-supervised alarm point.
The output relays can also be configured for fail-safe or fail-secure operation. Each relay supports
the “On,” “Off,” and “Pulse” Lenel OnGuard software commands.
Features and Functionality
■ Grade B, A, and AA line supervision
■ 12 or 24 VDC input power
■ 16 programmable supervised or non-supervised contacts
■ 2 Form-C 5 A, 30 VDC contacts for load switching
■ 2 dedicated inputs for tamper and power failure status
■ On-board termination jumpers
■ DIP switch-selectable addressing
■ Elevator control, support for 64 floors
■ Status LED for host communication and heartbeat
■ Variable resistor values for line supervision
■ Downloadable firmware
15
LNL-1100 Series 2
OnGuard
Security
Server
CORPORATE HEADQUARTERS
LOCAL AREA NETWORK (TCP/IP)
Intelligent
System
Controller
LNL-1300
Single Reader
Interface Module
LNL-1320
Dual Reader
Interface Module
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Access Control
RS-485 multidrop
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply
current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Lenel UL-listed power supply - 12 or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 A) input, continuous supply current with
enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery
optional), UL-listed
Battery Kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC)
DC input:
Memory and Clock Backup
Environmental
Temperature:
Humidity:
Mechanical
Dimension:
Weight:
Approvals
* The ICM is for use in low voltage, power-limited, class 2 circuits only.
12 or 24 VDC ± 15%. 350 mA
3 V lithium, type BR2325
Operating: 0° to +70° C (32° to 158° F)
Storage: -55° to +85° C (-67° to 185° F)
0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)
10 oz. (290 g) nominal
UL 294 and 1076-listed, CE-marked, ROHS compliant
16
Output Control Module
LNL-1200 Series 2
The Lenel Output Control Module (OCM) communicates directly with the Intelligent System
Controller (ISC) by either 2-wire or 4-wire RS-485 communication. Each OCM is an
individually-addressed device, and counts as a single device on all Intelligent System Controllers.
The OCM can be operated by either 12 or 24 VDC power. Each OCM includes dedicated tamper
and power failure input contacts.
The OCM has 16 programmable output relays that can be configured for fail-safe or fail-secure
Access Control
operation. Each relay supports the “On,” “Off,” and “Pulse” Lenel OnGuard software commands.
Features and Functionality
■ 16 Form-C 5 A, 30 VDC contacts for load switching
■ 12 or 24 VDC input power
■ 2 dedicated digital inputs for tamper and power failure status
■ RS-485 communication, multidropped (2-wire or 4-wire RS-485)
■ Up to 16 OCMs per Intelligent System Controller
■ On-board termination jumpers
■ DIP switch-selectable addressing
■ Status LEDs for communication to the host, heartbeat and relay status
■ Elevator control, support for 64 floors
17
LNL-1200 Series 2
OnGuard
Security
Server
CORPORATE HEADQUARTERS
LOCAL AREA NETWORK (TCP/IP)
Intelligent
System
Controller
LNL-1300
Single Reader
Interface Module
LNL-1320
Dual Reader
Interface Module
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Access Control
RS-485 multidrop
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current with
enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional),
UL-listed
Lenel UL-listed power supply - 12 VDC or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply current
with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional),
UL-listed
Battery kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC)
DC input:
Environmental
Temperature:
Humidity:
Mechanical
Dimension:
Weight:
Approvals
* The OCM is for use in low voltage, power-limited, class 2 circuits only.
12 or 24 VDC ± 15%. 500 mA
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)
16 oz. (454 g) nominal
UL 294 and 1076-listed, CE-marked, ROHS compliant
18
Star Multiplexer
LNL-8000
The Star Multiplexer from Lenel is designed to implement star topology on a downstream port of
any Lenel Intelligent System Controller or on any host communication port of any OnGuard server.
Up to eight RS-485 (2-wire) connections or four RS-485 (4-wire) connections can be made
downstream of the LNL-8000. The Lenel Star Multiplexer requires 12 VDC for power. It allows
communication protocol conversion, and provides connection with alternate communication
devices to extend effective distances.
Access Control
The master or host interface can use either RS-232 or RS-485 (2-wire) communication. The Lenel
Star Multiplexer interfaces upstream with the Lenel ISC, and downstream with one of many Lenel
RS-485 products (including the LNL-1100 Input Control Module, LNL-1200 Output Control Module,
LNL-1300 Single Reader Interface Module, LNL-1320 Dual Reader Interface Module and
LNL-500A, LNL-500B, or LNL-500W Gateway Interface Modules) on each downstream port (ports
2-9). A maximum of eight (8) devices are allowed per downstream port.
Features and Functionality
■ Host communications - 38.4 Kbps direct wire (RS-232/RS-485 multidropped)
■ 12 VDC input power
■ Status LEDs for heartbeat, upstream and downstream communication
■ Support for either 2-wire or 4-wire RS-485 topologies
■ RS-485 on-board termination is jumper selectable
■ Can be used for retrofit and new wiring configurations
23
LNL-8000
OnGuard
Security
Server
LNL-8000
Star Multiplexer
23456789
Intelligent
System
Controller
1234
1234
Up to 32 Downstream
RS-485 Devices
(up to 8 per port)
Intelligent
System
Controller
1234
LNL-8000
Star Multiplexer
(Up to 4 multiplexers)
23456789
LNL-1300
LNL-1320
Access Control
Intelligent
System
Controller
Mechanical and Architectural Characteristics and Wiring
Requirements
Communications
The acceptable power supply is 12 VDC. Locate the power source as close as possible to the LNL-8000.
Use a minimum of 18 AWG (one twisted pair) wiring for the power supply.
Communication with the Intelligent System Controller is via a 2-wire or 4-wire RS-485 interface. The interface allows multidrop
communication on a single ISC port, up to 4,000 feet (1219 m) away per port. It also can be used to convert a single RS-232
communication port to a multidrop RS-485 port. Use twisted pair(s) with a minimum of 24 AWG and a shield for communication.
The 2-wire or 4-wire communications with end-of-line termination are jumper-selectable.
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL-listed 4 A, 110 VAC power supply - 12 VDC or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply
current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Lenel UL-listed power supply - 12 VDC or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply
current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Battery kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC or AC)
DC input:
Environmental
Temperature:
Humidity:
Mechanical
Dimensions:
Weight:
Approvals
* This module is for use in low voltage, power limited, class 2 circuits only.
12 VDC ± 15%, 250 mA
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
6 x 5 x 1 in. (152 x 127 x 25 mm)
4 oz. (180 g) nominal
UL 294 and 1076-listed, CE-marked
24
AL400ULX(R) Power Supply/Chargers
Rev. DSAL400ULX - F06G
Overview
• These multi-agency approved single output power supply/chargers convert a
115VAC/60Hz input into one (1) Class 2 Rated 12VDC or 24VDC power
limited output.
AL400ULX
• Grey enclosure.
AL400ULXR
• Red enclosure.
Specifications
•
•
•
•
•
•
•
•
12VDC or 24VDC selectable output.
12VDC @ 4 amp or 24VDC @ 3 amp supply current.
Class 2 Rated power limited output.
Input 115VAC / 60Hz, 1.45 amp.
Input fuse rated @ 3.5 amp/250V.
Filtered and electronically regulated output.
Short circuit and thermal overload protection.
Built-in charger for sealed lead acid
or gel type batteries.
• Maximum charge current .7 amp.
• Automatic switch over to stand-by battery when
AC fails (zero voltage drop).
• AC fail supervision (form "C" contacts).
•
•
•
•
Low battery supervision (form "C" contacts).
Battery presence supervision (form “C” contacts).
AC input and DC output LED indicators.
Enclosure:
- Combination knockouts are 1/2” and 3/4”
- Accommodates up to two (2) 12VDC/7AH batteries.
• Product weight:
- AL400ULX: 7.3 lbs.
- AL400ULXR: 6.3 lbs.
• Shipping weight:
- AL400ULX: 8.2 lbs.
- AL400ULXR: 7.3 lbs.
Agency Approvals
UL Listed for Access Control
System Units.
UL 603 UL Listed Standard for Power
Supplies for Use with BurglarAlarm Systems.
UL 1069 UL Listed Hospital Signaling and
Nurse Call Equipment.
UL 1481 UL Listed Standard for Safety for
Fire Protective Signaling Systems.
UL 294
CUL Listed - CSA Standard C22.2
No.205-M1983, Signal Equipment.
MEA - NYC Department of
Buildings Approved.
CSFM - California State Fire
Marshal Approved.
FM - Factory Mutual Approved.
Enclosure Dimensions
13.5”H x 13”W x 3.25”D
1.40"
4.85"
4.85"
1.40"
1.20"
3.25"
Top
12.50"
1.20"
0.75"
1.20"
0.75"
11.00"
0.9375"
1.40"
1.40"
5.10"
5.10"
Left
Right
5.10"
6.5625"
0.9375"
3.25"
3.25"
Bottom
3.25"
1.00"
1.00"
1.00"
10.50"
Altronix Corp. - 140 58th Street, Brooklyn, NY 11220 • 718-567-8181 • 888-258-7669 • altronix.com
1.00"
AL600ULX(R) Power Supply/Charger
Rev. DSAL600ULX - F07G
Overview
• These multi-agency approved single output power supply/chargers convert a
115VAC/60Hz input into one (1) 12VDC or 24VDC
non-power limited output.
AL600ULX
• Grey enclosure.
AL600ULXR
• Red enclosure.
Specifications
•
•
•
•
•
•
•
12VDC or 24VDC selectable output.
6 amp supply current.
Input 115VAC / 60Hz, 1.9 amp.
Input fuse rated @ 3.5 amp/250V.
Filtered and electronically regulated output.
Short circuit and thermal overload protection.
Built-in charger for sealed lead acid
or gel type batteries.
• Maximum charge current .7 amp.
• Automatic switch over to stand-by battery when
AC fails (zero voltage drop).
• AC fail supervision (form “C” contacts).
•
•
•
•
Low battery supervision (form “C” contacts).
Battery presence supervision (form “C” contacts).
AC input and DC output LED indicators.
Enclosure:
- Combination knockouts are 1/2" and 3/4"
- Accommodates up to two (2) 12VDC/7AH batteries.
• Product weight:
- AL600ULX: 7.6 lbs.
- AL600ULXR: 6.6 lbs.
• Shipping weight:
- AL600ULX: 8.5 lbs.
- AL600ULXR: 7.6 lbs.
Agency Approvals
UL 294
UL Listed for Access Control
System Units.
UL 603 UL Listed Standard for Power
Supplies for Use with BurglarAlarm Systems.
UL 1069 UL Listed Hospital Signaling and
Nurse Call Equipment.
UL 1481 UL Listed Standard for Safety for
Fire Protective Signaling Systems.
CUL Listed - CSA Standard C22.2
No.205-M1983, Signal Equipment.
MEA - NYC Department of
Buildings Approved.
CSFM - California State Fire
Marshal Approved.
FM - Factory Mutual Approved.
Enclosure Dimensions
13.5”H x 13”W x 3.25”D
1.40"
4.85"
4.85"
1.40"
1.20"
3.25"
Top
12.50"
1.20"
0.75"
1.20"
0.75"
11.00"
0.9375"
1.40"
1.40"
5.10"
5.10"
Left
Right
5.10"
6.5625"
0.9375"
3.25"
3.25"
Bottom
3.25"
1.00"
1.00"
1.00"
10.50"
Altronix Corp. - 140 58th Street, Brooklyn, NY 11220 • 718-567-8181 • 888-258-7669 • altronix.com
1.00"
PD8, PD8CB Power Distribution Modules
Rev. DSPD8/CB - A17F
Overview
• These power distribution modules convert a single AC or DC input into
eight (8) individual outputs.
PD8
• Converts a single AC or DC input
into eight (8) individual fuse
protected outputs rated @ 3.5
amp each, (fuses are rated @ 3.5 amp
up to 5 amp fuses may be used).
PD8CB
• Converts a single AC or DC input
into eight (8) individual PTC
protected outputs rated @ 2.5
amp each.
Specifications
• Power output LED indicator.
• Power ON/OFF switch.
• 28VAC or 28VDC up to 10 amp.
• Eight (8) individual outputs.
• Surge suppression.
Board Dimensions (approximate)
5.25"H x 3.25"W x 1"D
Mounting Diagram
0.33"
Ø0.156"
4.9"
0.13"
2.4"
3.4"
5.2"
Altronix Corp. - 140 58th Street, Brooklyn, NY 11220 • 718-567-8181 • 888-258-7669 • altronix.com
Tripp Lite
1111 West 35th Street
Chicago, IL 60609 USA
Telephone: +(773) 869 1234
E-mail: saleshelp@tripplite.com
Model #: SU2200RTXL2UA
SmartOnline Expandable 2U Rack / Tower UPS System - On-line, double-conversion, sine wave UPS with PDU
switching, current monitoring and fault tolerant auto-bypass
Highlights
2200VA / 2.2kVA on-line, double-conversion, extended-run 2U rack / tower
UPS
Zero transfer time, on-line, double-conversion and economy-mode operation
supported
Maintains sine-wave 110/120V +/-2% output during overvoltages to 138 and
brownouts as low as 65V (50/60Hz auto-sensing)
Simultaneous communications via HID compliant USB port, serial port,
SNMP/Web card slot and EPO interface
Fault tolerant auto-bypass mode, current monitoring and switched PDU control
via 2 switchable output load banks
Input: NEMA 5-20P (120V) / Output: 6 NEMA 5-15/20R and 1 NEMA L5-20R
(120V)
2 year product warranty / $250,000 Ultimate Lifetime Insurance (USA &
Canada only)
Description
2200VA on-line, double-conversion UPS system for critical server, network and telecommunications equipment. 2U rackmount form factor with an
installed depth of only 19 in. Expandable battery runtime with optional BP48V24-2U and BP48V60RT-3U external battery packs. Full-time sine wave
110 or 120V +/-2% output. Online, double-conversion Uninterruptible Power Supply (UPS) actively converts raw incoming AC power to DC, then
re-converts output back to completely regulated, filtered AC output. Operates continuously without using battery power during brownouts to 65V and
overvoltages to 138V. NEMA 5-20P input plug; NEMA 5-15/20R and NEMA L5-20R output receptacles. Network-grade AC surge and noise
suppression. Zero transfer time between AC and battery operation. Highly efficient operation in optional economy mode setting, saving BTU heat
output and energy costs. Network management interfaces support simultaneous communications via USB port, DB9 serial port and
SNMPWEBCARD slot. HID-compliant USB interface enables integration with built-in power management and auto shutdown features of Windows
and Mac OS X. Supports simultaneous detailed monitoring of equipment load levels, self-test data and utility power conditions via all 3 network
interfaces. Includes PowerAlert monitoring software and complete cabling. Emergency Power Off (EPO) interface. Integrated 2-bank PDU switching
supports load shedding and remote-reboot of connected equipment. 3-stage metered current monitoring and battery charge status LEDs. LED
display panel easily rotates for better viewing in rackmount or tower configurations. Dataline surge suppression for dialup, DSL or network Ethernet
connection. Utility power and voltage regulation LEDs. Audible alarm. Self-test. Fault-tolerant auto-bypass mode. 4-post rackmount accessories
included; 2-9USTAND tower kit and 2POSTRMKITWM two post rack & wallmount accessories available. Field-replaceable, hot-swappable internal
batteries and external battery packs. Attractive all-black color scheme. 2-year warranty and $250,000connected equipment insurance; extended
warranty and service contracts available
Package Includes
SU2200RTXL2Ua On-line Double-Conversion UPS System
PowerAlert Software and cabling
Mounting hardware for 4 post rack enclosures
Instruction manual with warranty information
Features
SmartOnline high performance UPS system is ideal for critical voice, data, medical and industrial network applications
True on-line, double-conversion UPS provides perfectly regulated sine wave output within 2% of 110/120V (user selectable) under all usage
conditions
Maintains continuous operation through blackouts, voltage fluctuations and surges with zero transfer time
Removes harmonic distortion, fast electrical impulses, frequency variations and other hard to solve power problems not addressed by other
UPS types
Corrects line voltage conditions as low as 65V and as high as 138V back to selectable 110/120V (+/-2%) values
Standard internal battery set offers 14 minutes runtime at half load (800W) and 4.5 minutes at full load (1600W)
Extended Runtime with BP48V24-2U (limit 1) or BP48V60RT3U (multi-pack compatible) external battery packs
Compact rackmount form factor installs using only 2 rack spaces (2U) with a maximum installed depth of only 19 inches
Ships with all mounting accessories for 4 post rackmount installation
Optional 2POSTRMKITWM enables 2 post rackmount or wallmount installation
Optional 2-9USTAND accessory enables small-footprint upright tower placement
Fault tolerant auto-bypass maintains continuous utility output to connected equipment, even in cases where the UPS suffers internal failure
and requires maintenance
Network interfaces support simultaneous communications via built-in USB, DB9 serial and SNMPWEBCARD slot
HID compliant USB interface enables integration with built-in power management and auto shutdown features of Windows and Mac OS X
Included PowerAlert UPS monitoring software supports safe unattended shutdown, monitoring and control via local connected servers, plus
any number of additional servers over IP
UPS interface supports on-battery, low-battery, power-restored, AC-voltage, DC-voltage, output current monitoring, battery charge current,
battery capacity, AC line frequency, timed inverter sutoff, activate self-test, load bank output power control and remote reboot, UPS nominal
voltage adjustment and UPS line to battery power voltage setpoints
Built-in Emergency Power Off (EPO) interface with cable
NEMA 5-20P input plug (user-installable NEMA 5-15P replacement plug included)/NEMA 5-15/20R & NEMA L5-20R output receptacles
Integrated 2 bank switched PDU enables remote outlet management for load shedding or remote reboot of individual load banks (each
bank has 3 outlets)
Front panel LEDs offer current monitoring and battery charge level information
UPS ships fully assembled in full compliance with DOT regulations, no time consuming connection of internal batteries by user required
Single line TEL/DSL or network ethernet line surge suppression
2 year manufacturer's product warranty, $250,000 Ultimate Lifetime Insurance
Specifications
OUTPUT
Output Volt Amp
Capacity (VA)
2200
Output kVA capacity
(kVA)
2.2
Output Watt Capacity
(watts)
1600
Output kW capacity
1.6
Output power factor
0.7
Crest Factor
3:1
Nominal Output
Voltage(s) Supported
110v; 120v
Nominal Voltage
details
120V default
Frequency
compatibility
50 / 60 Hz
Frequency
compatibility details
Output frequency matches input nominal on startup, defaults to 60 Hz on cold-start
Output voltage
regulation (line mode)
+/- 2%
Output voltage
regulation (Economy
line mode)
+/- 10%
Output voltage
regulation (Battery
mode)
+/- 2%
Built-in UPS output
receptacles
6 5-15/20R outlet(s); 1 L5-20R outlet(s)
Built-in controllable
switched load banks
Two switchable three-outlet 5-15/20R load banks
Basic PDU options
PDUNV (1U / 2 C19, 12 C13 outlets); PDU1420T (0U / 14 5-15/20R outlets); PDU40TDUAL (0U / 40 5-15/20R outlets)
Metered PDU options
PDUMH20 (1U / 13 5-15/20R outlets); PDUMH20AT (1U / 16 5-15/20R outlets)*; PDUMV20 (0U / 16 5-15/20R
outlets); PDUMV40 (0U / 32 5-15/20R outlets)
Switched PDU options
PDUMH20ATNET (1U / 16 5-15/20R outlets)*; PDUMV20NET (0U / 24 5-15/20R outlets)
External PDU
redundancy options
*ATS switch options PDUMH20AT & PDUMH20ATNET support dual UPS and hot-swappable UPS configurations
Output AC waveform
(AC mode)
Sine wave
Output AC waveform
(battery mode)
Sine wave
INPUT
Rated input current
(at maximum load)
16A
Nominal input
voltage(s) supported
110V AC; 120V AC
UPS input connection
type
5-20P
UPS input connection
description
Includes user-installable 5-15P replacement plug
Input circuit breaker
30A
UPS Input cord length
(ft.)
10
UPS Input cord length
(m)
3
Recommended
Electrical Service
20A 120V
BATTERY
Full load runtime
(minutes)
4.5 min. (1600w)
Half load runtime
(minutes)
14 min. (800w)
Expandable battery
runtime
Extended runtime supported via optional external battery packs
External battery pack
compatibility
BP48V24-2U (limit 1); BP48V60RT3U (multi-pack compatible)
DC system voltage
48V DC
Battery recharge rate
(included batteries)
Less than 6 hours from 10% to 80%
Replacement battery
cartridge (internal
UPS battery
replacement)
RBC94-2U
Battery Access
Front panel battery access door
Battery replacement
description
Hot-swappable, user replaceable batteries
VOLTAGE REGULATION
Voltage regulation
description
Online, double-conversion power conditioning
Overvoltage
correction
2% output voltage regulation during overvoltages to 138
Undervoltage
correction
2% output voltage regulation during undervoltages to 80
Severe undervoltage
correction
2% output voltage regulation during undervoltages to 65 (under 70% load only)
LEDS ALARMS & SWITCHES
LED Indicators
14 LEDs indicate line power, online mode, economy/bypass mode, on-battery, overload, battery low, replace battery
and fault status information; 4-LED meter displays load and battery charge levels; LED panel rotates for viewing in
rack/tower formats
Alarms
Audible alarm indicates UPS startup, power-failure, low-battery, overload, UPS fault and remote shutdown conditions
Alarm cancel
operation
Power-fail alarm can be silenced using alarm-cancel switch
Switches
2 Switches control off/on power status and alarm-cancel/self-test operation
SURGE / NOISE SUPPRESSION
UPS AC suppression
joule rating
570
UPS AC suppression
response time
Instantaneous
UPS Dataline
suppression
1 line TEL / DSL or 10Base T Ethernet protection
EMI / RFI AC noise
suppression
Yes
PHYSICAL
Installation form
factors supported
with included
accessories
4 post 19 inch rackmount (mounting rail kit included); 2 post rackmount (use 2POSTRMKITWM); Wallmount (use
2POSTRMKITWM); Tower (use 2-9USTAND)
Installation form
factors supported
with optional
accessories
2 post rackmount (use 2POSTRMKITWM); Wallmount (use 2POSTRMKITWM); Tower (use 2-9USTAND)
Primary form factor
Rackmount
UPS / Power Module
dimensions in
primary form factor
(height x width x
depth / inches)
3.50 x 17.50 x 19.00
UPS / Power Module
dimensions in
primary form factor
(height x width x
depth / cm)
8.89 x 44.45 x 48.26
Installed whole
system total rack
space height (rack
spaces)
2U
Secondary form factor
Tower (requires 2-9USTAND)
Installed whole
system dimensions in
secondary form factor
(height x width x
depth / inches)
17.5 x 3.5 x 19
UPS dimensions in
secondary form factor
(height x width x
depth / cm)
44.4 x 8.9 x 48.3
UPS / Power Module
weight (lbs)
47.4
UPS / Power Module
weight (kg)
21.5
UPS Shipping
dimensions (height x
width x depth / inches)
9.75 x 20.25 x 24.00
UPS Shipping
dimensions (height x
width x depth / cm)
24.77 x 51.44 x 60.96
Shipping weight (lbs)
57.3
Shipping weight (kg)
26
UPS housing material
Steel
Cooling method
Fan
ENVIRONMENTAL
Operating
Temperature Range
+32 to +104 degrees Fahrenheit / 0 to +40 degrees Celsius
Storage Temperature
Range
+5 to +122 degrees Fahrenheit / -15 to +50 degrees Celsius
Relative Humidity
0 to 95%, non-condensing
AC mode BTU / hr.
(full load)
812.9
AC economy mode
BTU / hr. (full load)
347.2
Battery mode BTU /
hr. (full load)
885.6
AC economy mode
efficiency rating
(100% load)
94%
COMMUNICATIONS
Communications
interface
USB (HID enabled); DB9 Serial; Contact closure; EPO (emergency power off); Slot for SNMP/Web interface
Network monitoring
port description
Supports detailed monitoring of UPS and site power conditions; DB9 port supports RS232 and contact closure
communications
PowerAlert software
Included
Communications
cable
USB and DB9 cabling included
WatchDog
compatibility
Supports Watchdog application, OS and hard-reboot restart options for remote applications
LINE / BATTERY TRANSFER
Transfer time
No transfer time (0 ms.) in online, double-conversion mode
Low voltage transfer
to battery power
(setpoint)
80V (100% load), 65V (
High voltage transfer
to battery power
(setpoint)
138
SPECIAL FEATURES
Cold Start (startup in
battery mode during a
power failure)
Cold-start operation supported
High availability UPS
features
Automatic inverter bypass; Hot swappable batteries
Green & high
efficiency features
High efficiency economy mode operation; Individually controllable load banks; Schedulable daily hours of economy
mode operation
CERTIFICATIONS
UPS Certifications
Tested to UL1778 (USA); Tested to CSA (Canada); Tested to NOM (Mexico); Meets FCC Part 15 Category A (EMI);
Meets FCC Part 68 / Industrie Canada (telecommunications); ROHS (Reduction of Hazardous Substances)
WARRANTY & INSURANCE
Standard warranty
period
2 years
Connected equipment
insurance (USA,
Canada, Puerto Rico)
$250,000 connected equipment insurance
Related Items
Extended Warranties
WEXT3-2200-3000
3-Year Extended Warranty - For Smart Line-Interactive and Online Tower or Rack models,
2200-3000VA
Qty: [optional]
WEXT5-2200-3000
5-Year Extended Warranty - For Smart Line-Interactive and Online Tower or Rack models,
2200-3000VA or less
Qty: [optional]
BP48V24-2U
BP48V242U - External Battery Pack for UPS System
Qty: [optional]
BP48V60RT-3U
External Battery Pack and Cable. 3U, Expandable, Blue 2-Point Connector
Qty: [optional]
PS7224
Tripp Lite Power Strip - Multiple outlets wherever you need them
Qty: [optional]
PDU1215
Basic PDU / Power Distribution Unit - Safe, reliable power distribution for critical networking
equipment
Qty: [optional]
Universal 2-Post Rackmount Kit (Supports 2U to 4U UPS systems and battery packs.)
Qty: [optional]
Power Management Tools - UPS Communication Cable Kit for System i / AS400 / iSeries
Servers
Qty: [optional]
ENVIROSENSE
Monitors temperature, humidity and contact-closure inputs. (Requires SNMPWEBCARD or
switched PDU.)
Qty: [optional]
SNMPWEBCARD
For remote monitoring and control via SNMP, Web or telnet.
Qty: [optional]
DTEL2
Network Surge Suppressor - Essential protection for data and communication lines
Qty: [optional]
DNET1
Network Surge Suppressor - Essential protection for data and communication lines
Qty: [optional]
DCATV
Network Surge Suppressor - Essential protection for TV/VCR coaxial lines
Qty: [optional]
External Battery Packs
Power Distribution
Rackmount/Wallmount Kits
2POSTRMKITWM
Shutdown Cable Kits
AS400CABLE KIT
SNMP Accessories
Surge Protectors
Tower Stands
2-9USTAND
Tower Stand - Expandable Tower Base Stand UPS Accessory
More information, including related products, owner's manuals, and additional technical specifications, can be found online at
www.tripplite.com/en/products/model.cfm?txtModelID=2950.
©2009 Tripp Lite. All Rights Reserved.
Qty: [optional]
Medium Type 1 Enclosures
Type 1 Boxes and
Enclosures
Bulletin
A1M
Construction
• 16 or 14 gauge steel
• Mounting holes on back of enclosure
Finish
ANSI 61 gray polyester powder paint finish inside and out over
phosphatized surfaces. Optional solid panels are white and optional
perforated panels are gray.
Industry Standards
UL 50, File No. E27567, Type 1
NEMA/EEMAC Type 1
CSA, File No. 42184, Type 1
IEC 60529, IP30
Accessories
See also Accessories chapter.
Application
Designed for use in control and instrumentation applications in areas
which do not require oiltight and dusttight specifications.
Cylinder Lock Kit (AL12AR)
Electric Heater
Electrical Interlock
Grounding Device
Panels
Rack Mounting Angle Kit
“T” Handle Latch Kit (AL7A)
Touch-Up Paint (ATPPY61)
Window Kit
Features
• Doors have butt hinges
• Collar studs provided for mounting optional panel
• Slotted flush latches. Optional latches available.
Device for utilization
Subject to change without notice
PH 763 422 2211 • FX 763 422 2600 • www.hoffmanonline.com
© 2007 Hoffman Enclosures Inc.
Type 1 Boxes and
Enclosures
Medium Type 1 Enclosures
Bulletin
A1M
Standard Sizes Medium Type 1 Enclosures
Catalog
Number
A16N12ALP
A16N16ALP
A16N20ALP
A20N16ALP
A20N20ALP
A24N16ALP
A24N20ALP
A24N24ALP
A30N24ALP
A36N24ALP
A16N12BLP
A20N12BLP
A20N16BLP
A20N20BLP
A24N20BLP
A24N24BLP
A30N20BLP
A30N24BLP
in. (mm)
16.00 x 12.00 x 6.62
(406 x 305 x 168)
16.00 x 16.00 x 6.62
(406 x 406 x 168)
16.00 x 20.00 x 6.62
(406 x 508 x 168)
20.00 x 16.00 x 6.62
(508 x 406 x 168)
20.00 x 20.00 x 6.62
(508 x 508 x 168)
24.00 x 16.00 x 6.62
(610 x 406 x 168)
24.00 x 20.00 x 6.62
(610 x 508 x 168)
24.00 x 24.00 x 6.62
(610 x 610 x 168)
30.00 x 24.00 x 6.62
(762 x 610 x 168)
36.00 x 24.00 x 6.62
(914 x 610 x 168)
36.00 x 30.00 x 6.62
(914 x 762 x 168)
16.00 x 12.00 x 8.62
(406 x 305 x 219)
20.00 x 12.00 x 8.62
(508 x 305 x 219)
20.00 x 16.00 x 8.62
(508 x 406 x 219)
20.00 x 20.00 x 8.62
(508 x 508 x 219)
24.00 x 20.00 x 8.62
(610x 508x 219)
24.00 x 24.00 x 8.62
(610 x 610 x 219)
30.00 x 20.00 x 8.62
(762 x 508 x 219)
30.00 x 24.00 x 8.62
(762 x 610 x 219)
30.00 x 30.00 x 8.62
(762 x 762 x 219)
36.00 x 24.00 x 8.62
(914 x 610 x 219)
36.00 x 30.00 x 8.62
(914 x 762 x 219)
18.00 x 18.00 x 10.62
(441 x 441 x 270)
24.00 x 20.00 x 10.62
(610 x 508 x 270)
30.00 x 24.00 x 10.62
(762 x 610 x 270)
24.00 x 24.00 x 12.62
(610 x 610 x 321)
30.00 x 24.00 x 12.62
(762 x 610 x 321)
36.00 x 30.00 x 12.62
(914 x 762 x 321)
Perforated
Panel
Catalog
Number
A16N12MP A16N12MPP
A16N16MP A16N16MPP
A16N20MP A16N20MPP
A20N16MP A20N16MPP
A20N20MP A20N20MPP
A24N16MP A24N16MPP
A24N20MP A24N20MPP
A24N24MP A24N24MPP*
A30N24MP A30N24MPP*
A36N24MP A36N24MPP*
A36N30MP A36N30MPP*
A16N12MP A16N12MPP
A20N12MP A20N12MPP
A20N16MP A20N16MPP
A20N20MP A20N20MPP
A24N20MP A24N20MPP
A24N24MP A24N24MPP*
A30N20MP A30N20MPP*
A30N24MP A30N24MPP*
A30N30MP A30N30MPP*
Devices for utilization
A30N30BLP
A36N24BLP
A36N30BLP
A18N18CLP
A24N20CLP
A30N24CLP
A24N24DLP
A30N24DLP
A36N30DLP
A36N24MP A36N24MPP*
A36N30MP A36N30MPP*
A18N18MP A18N18MPP
A24N20MP A24N20MPP
A30N24MP A30N24MPP
A24N24MP A24N24MPP*
A30N24MP A30N24MPP*
A36N30MP A36N30MPP*
Panel Size
DxE
in. (mm)
13.00 x 10.50
(330 x 267)
13.00 x 14.50
(330 x 368)
13.00 x 18.50
(330 x 470)
17.00 x 14.50
(432 x 368)
17.00 x 18.50
(432 x 470)
21.00 x 14.50
(533 x 368)
21.00 x 18.50
(533 x 470)
21.00 x 22.50
(533 x 572)
26.00 x 22.50
(660 x 572)
32.00 x 22.50
(813 x 572)
32.00 x 28.50
(813 x 724)
13.00 x 10.50
(330 x 267)
17.00 x 10.50
(432 x 267)
17.00 x 14.50
(432 x 368)
17.00 x 18.50
(432 x 470)
21.00 x 18.50
(533 x 470)
21.00 x 22.50
(533 x 572)
26.00 x 18.50
(660 x 470)
26.00 x 22.50
(660 x 572)
26.00 x 28.50
(660 x 724)
32.00 x 22.50
(813 x 572)
32.00 x 28.50
(813 x 724)
15.00 x 16.50
(381 x 419)
21.00 x 18.50
(533 x 470)
21.00 x 22.50
(533 x 572)
21.00 x 22.50
(533 x 572)
26.00 x 22.50
( 660 x 724)
32.00 x 28.50
(813 x 724)
Panel G
Ga. (in.)
G
H
(mm) (in.)
H
J
J
Q
Q
P
P
F
(mm) (in.) (mm) (in.) (mm) (in.) (mm) (in.)
F
K
K
(mm) (in.) (mm)
14
13.88 353
7.00
178
2.50 64
1.06 27
0.31 8
6.00 152
1.50 38
14
13.88 353
11.00 279
2.50 64
1.06 27
0.31 8
6.00 152
1.50 38
14
13.88 353
15.00 381
2.50 64
1.06 27
0.31 8
6.00 152
1.50 38
14
17.88 454
11.00 279
2.50 64
1.06 27
0.31 8
6.00 152
1.50 38
14
17.88 454
15.00 381
2.50 64
1.06 27
0.31 8
6.00 152
1.50 38
14
21.88 556
11.00 279
2.50 64
1.06 27
0.31 8
6.00 152
1.50 38
14
21.88 556
15.00 381
2.50 64
1.06 27
0.31 8
6.00 152
1.50 38
12
21.88 556
19.00 483
2.50 64
1.06 27
0.31 8
6.00 152
1.50 38
12
27.50 699
16.75 425
3.62 92
1.25 32
0.44 11
6.00 152
2.00 51
12
33.50 851
16.75 425
3.62 92
1.25 32
0.44 11
6.00 152
2.00 51
12
33.50 851
22.75 578
3.62 92
1.25 32
0.44 11
6.00 152
2.00 51
14
13.88 353
7.00
178
2.50 64
1.06 27
0.31 8
8.00 203
1.50 38
14
17.88 454
7.00
178
2.50 64
1.06 27
0.31 8
8.00 203
1.50 38
14
17.88 454
11.00 279
2.50 64
1.06 27
0.31 8
8.00 203
1.50 38
14
17.88 454
15.00 381
2.50 64
1.06 27
0.31 8
8.00 203
1.50 38
14
21.88 556
15.00 381
2.50 64
1.06 27
0.31 8
8.00 203
1.50 38
12
21.88 556
19.00 483
2.50 64
1.06 27
0.31 8
8.00 203
1.50 38
12
27.50 699
15.00 381
2.50 64
1.25 32
0.44 11
8.00 203
2.00 51
12
27.50 699
16.75 425
3.62 92
1.25 32
0.44 11
8.00 203
2.00 51
12
27.50 699
22.75 578
3.62 92
1.25 32
0.44 11
8.00 203
2.00 51
12
33.50 851
16.75 425
3.62 92
1.25 32
0.44 11
8.00 203
2.00 51
12
33.50 851
22.75 578
3.62 92
1.25 32
0.44 11
8.00 203
2.00 51
14
15.88 403
13.00 330
2.50 64
1.06 27
0.31 8
10.00 254
1.50 38
14
21.88 556
15.00 381
2.50 64
1.06 27
0.31 8
10.00 254
1.50 38
12
27.50 699
16.75 425
3.62 92
1.25 32
0.44 11
10.00 254
2.00 51
12
21.88 556
19.00 483
2.50 64
1.06 27
0.31 8
12.00 305
1.50 38
12
27.50 699
16.75 425
3.62 92
1.25 32
0.44 11
12.00 305
2.00 51
12
33.50 851
22.75 578
3.62 92
1.25 32
0.44 11
12.00 305
2.00 51
Commercial Boxes
and Enclosures
A36N30ALP
AxBxC
Panel
Catalog
Number
Purchase panels separately.
* Flanged on all four sides.
Subject to change without notice
PH 763 422 2211 • FX 763 422 2600 • www.hoffmanonline.com
© 2007 Hoffman Enclosures Inc.
Spec-00261
Rev. A
04/07
Video Recorders for OnGuard VideoManager™
DVC-ST Chassis (4U)
Overview
Lenel offers several powerful and easy-to-use video recording options for a multitude of digital
video recorder and network video recorder applications. With flexibility to meet needs ranging from
high-resolution to expansive online storage, Video Recorders from Lenel present many affordable
options for those considering upgrading an existing analog installation to those looking for a fresh,
network-centric solution. Video Recorders are available in stand-alone or integrated deployments.
OnGuard GO! configurations provide powerful stand-alone systems for customers needing a DVR
or NVR application. Additionally, OnGuard GO! customers can add access control and ID badging
DVR / GO!
to the stand-alone video recorder without needing an additional server or database! No matter the
application, Video Recorders from Lenel offer a powerful opportunity to address a critical staple in
any security program.
DVC-EX Chassis (3U)
Video Boards (DVB-408 & DVB-444)
Lenel offers two video boards, the DVB-408 and the DVB-444. Each board supports
industry-leading MPEG-4 recording compression. The affordable DVB-408 has eight channels of
capacity, while the DVB-444 has four channels and includes four on-board processors for more
efficient compression. Both board options give customers the ability to start and expand robust
video systems.
DVR / NVR / GO!
DVC-ST (4U)
Video
The DVC-ST is a reliable, rack-mountable digital video recorder with several recording and storage
options. The DVC-ST supports analog video recording with up to two DVB-408s, or up to two
DVB-444s. Each DVC-ST has three hard drive bays for SATA, allowing customers to expand to
greater than one terabyte of online storage. The DVC-ST includes a 4U, 19-inch rack mount digital
storage recorder with Windows XP Professional, 10/100/1000 Ethernet, one 80 GB internal
OS-only hard drive (optional 3 additional data hard drives), DVD/CD ROM, 1.44 floppy and mouse.
DVC-EX (3U)
The DVC-EX is a high-powered machine offering the most expansive storage capacity of any DVR
available. With eight hard drive bays, the DVC-EX has capacity for four terabytes of online
storage. In addition to storage, the DVC-EX also allows the customer to configure RAID 5 data
redundancy. The DVC-EX includes a 3U, 19-inch rack mount digital storage recorder with
Windows XP Professional, 10/100/1000 Ethernet, one 80 GB OS-hard drive (optional data hard
drives, maximum of eight), DVD/CD ROM, 1.44 floppy, mouse and rack mount rail.
51
DVC-ES
DVC-ES Chassis
The DVC-ES is an entry-level solution that is a great fit for small DVR applications. Available with a
single DVB-408, the DVC-ES comes in a tower form factor for easy placement in any security
office. It includes a tower chassis, digital storage recorder with Windows XP Professional,
10/100/1000 Ethernet, one 80 GB internal OS-only hard drive (optional 2 additional data hard
drives), CD ROM, 1.44 floppy and mouse.
DVC-1U
DVR
The DVC-1U is a powerful and easy to use Network Video Recorder (NVR) with a small footprint.
Occupying 1/4 to 1/3 the space of traditional video recorders, the 1U form factor can easily fit in
empty rack slots, rarely requiring additional racks to house it. The DVC-1U includes a 1U
DVC-1U
rack-mount chassis, digital storage recorder with Windows XP Professional, two 10/100/1000
Ethernet ports, one 80 GB internal OS-only hard drive, one 500 GB internal Data Storage Drive
(optional 2 additional data hard drives), and CD/RW-DVD/R.
DVC-DELL
The DVC-DELL features a trusted hardware standard supporting an entry-level NVR application.
The Dell solution offers IT-centric security operations the ability to develop a video program using
a factory-tested server configuration that optimizes performance and ensures reliability.
Video
Stand-alone Video Recorders - OnGuard GO!
(DVC-ST, DVC-EX & DVC-1U)
NVR / GO!
DVC-DELL
Customers looking for stand-alone digital video recorders can use a Lenel video recorder with the
OnGuard GO! configurations. The stand-alone video recorder’s OnGuard GO! configuration has
the administration applications and database on the video recorder, saving money by not requiring
a separate security server to launch the most powerful security system available. Furthermore,
customers can take the single stand-alone video recorder and add OnGuard’s robust Access
Control, Fire & Intrusion and ID Management applications, as well as countless software options.
For customers expanding an existing analog environment by upgrading to a DVR or by embracing
IP by migrating to network video, Lenel video recorders offer the flexibility to initiate an integrated
NVR / GO!
security architecture by focusing on stand-alone digital video, then expanding the system when the
time is right.
52
Fixed Dome Digital Network Camera
ICT 220 DN Plus
Full D1 resolution with a true de-interlaced filter produces brilliant, artifact-free video. Using
state-of-the-art MPEG-4 (video) and synchronized ADPCM (audio) encoding, the ICT 220 provides
superior video quality and improved network performance. The ICT 220 outperforms the
competition, when compared to other network cameras using still picture encoding technology
such as MJPEG or Wavelet. The ICT 220 utilizes superior cross bit rate encoding technology, ixBR
Control®, to deliver powerful bandwidth control. Using ixBR, digital video streams more fluidly
because the data is encoded and streamed at a constant rate, yet it retains all the rich data of
variable bit rate encoding!
Key Features
■ 3 Axis MiniDome (360° horizontal x 90° vertical)
■ Powerful MPEG-4 video compression
• Supports up to 30 frames per second at full D1 resolution
■ True de-interlaced filter
■ Bidirectional G.711 and G.726 audio communication
■ Synchronized full-duplex one channel audio and video
■ State-of-the-art CPU, separate codec and embedded software
■ Intelligent bit rate control (flexible for difficult network environments)
■ Embedded streaming server and embedded Web server
Video
■ Motion-detected and event-triggered alarm processing
■ Sensor-triggered recording and FTP:
• One (1) alarm input
• One (1) relay output
■ Supports a wide range of network protocols
■ 1/3 in. (8 mm) Sony Super HAD CCD
• 410K CCD Day-Night with IR cut filter varifocal lens
• 410K CCD standard varifocal lens
• 270K CCD fixed lens
■ True Day-Night capability
■ System time management
• RTC with Time Server synchronization
■ Security support:
• User authentication
• 128-bit encrypted data stream (selectable, for added security)
53
ICT 220 DN Plus
Resolution
Power and Ethernet
■ NTSC: 30 fps
■ NTSC: 704x480 / 352x240 / 176x144
■ Power supply input voltage: 100~250 VAC 50-60 Hz
■ PAL: 25 fps
■ PAL: 704x576 / 352x288 / 176x144
■ Power supply output voltage: 12 VAC @ 3.3 A
■ AC power cable capacity: 250 VAC, 10~16 A
Certifications
■ Camera power input: 7~23V DC Max 8 Watts
■ UL
■ CE
■ Mid span PoE injector power input: 12V DC 1 Amp
■ ULC
■ CCC
■ Power supply connector type: N (male)
■ FCC
■ RoHS
■ Ethernet: 10/100Base-T autosensing
RCA Analog Display Cable
Package Contents
RCA analog cable is for analog video output from camera module
■ Camera
inside of network camera. Use with handheld video monitor for quick
■ Power supply
and easy focus and field of view setup. Connects to video output.
■ Type N male power connector with leads
■ Single port mid span PoE injector
■ Power cords
■ CD-ROM with software & user guide
■ RCA analog display cable
■ Install template and mounting screws
Camera Dimensions
Video
■ 5.6 x 5 in. (142 mm x 128 mm)
Part Number by Model and Region
Region
Model – ICT220 DN Plus
( 410KCCD- Day-Night)
Model- ICT220S
(410KCCD )
Model- ICT220S
( 270KCCD )
Americas- Asia Pacific
ICT2201DN
ICT2201S
ICT2201
Australia
ICT2202DN
ICT2202S
ICT2202
UK
ICT2203DN
ICT2203S
ICT2203
Europe
ICT2204DN
ICT2204S
ICT2204
Lens
Model
Lens
Minimum Illumination (Lux)
ICT220DN Plus
Varifocal 4.0 – 9.0 mm F1.2
0.1Lux / f=1.4 (AGC 0n)
ICT220S
Varifocal 4.0 – 9.0 mm F1.2
0.1Lux / f=1.4 (AGC 0n)
ICT220
Fixed 3.8 mm F2.0 manual focus
0.3Lux
54
C660 QD104 1-07.fm Page 635 Sunday, February 11, 2007 2:34 PM
PRODUCT SPECIFICATION
control site
QD104 Series Digital Quad Video Processor
COLOR/BLACK-WHITE, ALARMS
Product Features
• High-Quality Quad Display (1024H x 512V)
• Real-Time Quad Video
• Low Cost
• Four Camera Inputs with Four Looping Outputs
• Quad Monitor Output That Displays Continuous Four-Camera Image
• Call Monitor Output That Displays Full-Screen or Quad Image
• Sequencing of Full-Screen and Quad Views
• Automatic Time-Base Correction Eliminates the Need for Camera
Synchronization
• Five Alarm Inputs, One Alarm Output
The QD104 Series Quad is a high quality, low cost, color/
black-white video processor capable of displaying full-screen or
quad views of four camera inputs.
A quad monitor output displays a continuous quad image. For
greater versatility, a call monitor output offers several additional
viewing options. For more detail or easier viewing, the call monitor
output can display a full-screen view of any camera output. Or this
output can be used to display the quad image on a second monitor.
And the call monitor output supports sequencing. Sequencing can
include full-screen views of any of the four cameras as well as the
quad image. Camera selection and sequence programming for the
call monitor is done with front panel push buttons.
There are five alarm inputs, one for each of the four cameras, plus
one for the quad input. When there is an alarm, that camera is
switched to the call monitor’s output for the duration of the alarm or
until an operator acknowledges the alarm by pressing the front
panel button associated with the alarmed camera. Multiple alarms
will sequence at a two-second rate. An alarm output can trigger a
VCR or an external alarm indicator, such as a light or buzzer.
The quad comes in a desktop cabinet of the same style as the
Genex® Series multiplexer. A 9-inch (23 cm) monitor can be placed
on top of the unit. A separate rack kit provides all the hardware
necessary to mount one or two quads in a standard 19-inch (48 cm)
equipment rack. The rack kit includes a filler panel when installing a
single quad.
All camera inputs have looping outputs that add to the capability of
the quad by providing connections for additional video equipment.
A real-time quad update rate assures live video on all camera
outputs. And automatic time base correction means no external
synchronization of cameras is required. If any camera input loses
video, the monitor display for that camera appears black.
C660 / REVISED 1-07
International Standards
Organization Registered Firm;
ISO 9001 Quality System
C660 QD104 1-07.fm Page 636 Sunday, February 11, 2007 2:34 PM
TECHNICAL SPECIFICATIONS
MODELS
GENERAL
QD104C
QD104M
Color quad, NTSC, 120 VAC, 60 Hz
Black-white quad, EIA, 120 VAC, 60 Hz
Operating Temperature
Relative Humidity
Dimensions
1 Vp-p, composite
525 lines, 60 fields/second
1024 (H) x 512 (V) pixels
Real time
Finish
Unit Weight
Shipping Weight
32° to 120°F (0° to 49°C)
95%, non-condensing
1.73" H x 10.20" D x 8.44" W
(4.39 x 25.90 x 21.43 cm)
Charcoal gray
3 lb (1.36 kg)
4 lb (1.81 kg) approximate
VIDEO
Input Level
Video Standard
Digital Image
Quad Update Rate
Analog Frequency
Response
Crosstalk at Color
Subcarrier
Differential Gain
Differential Phase
Signal-to-Noise Ratio
CERTIFICATIONS
Better than 12 MHz
Better than -60 dB
Less than 2 percent
Less than 2 degrees
Better than -60 dB
• FCC, Class B (QD104C)
• FCC, Class A (QD104M)
OPTIONAL ACCESSORIES
RK100
Rack-mount kit (1 RU) for mounting one or two
QD100 Series Quads in a standard 19-inch
rack. Blank filler panel provided.
ELECTRICAL
Operating Voltage
Power
Video Inputs
Monitor Outputs
Alarm Inputs
Alarm Output
Alarm Clearance
Sequence Dwell Times
12 VAC; unit includes power supply
6 watts
Four, BNC, looping, 75-ohm/Hi Z termination
Two, BNC, 75 ohms
Five N.O. inputs
10K ohm output resistance; TTL, CMOS
compatible
Automatic with manual override
Programmable for 2, 4, 8, or 16 seconds
Notice: Judgment as to the suitability of the products for users’ purposes is solely the
users’ responsibility. Users should refer to the Operation manuals for cautionary
statements regarding user selected options and how they might affect video quality.
Users shall determine the suitability of the products for their own intended application,
picture rate and picture quality. In the event users intend to use the video for
evidentiary purposes in a judicial proceeding or otherwise, users should consult with
their attorney regarding any particular requirements for such use.
Pelco Worldwide Headquarters:
3500 Pelco Way, Clovis, California 93612-5699 USA
USA & Canada Tel: (800) 289-9100 • FAX (800) 289-9150
International Tel: (559) 292-1981 • FAX (559) 348-1120
www.pelco.com
Pelco, the Pelco logo, and Genex are registered trademarks of Pelco.
Specifications subject to change without notice.
©Copyright 2007, Pelco. All rights reserved.
R2416UL, R2416ULCB UL Listed
Rack Mount CCTV Power Supply
Rev. DSR2416UL - A27F
Overview
• These Altronix AC Rack Mount CCTV Power Supplies provide 24VAC or
28VAC distributed via sixteen (16) fuse or Class 2 Rated PTC protected
power limited outputs for powering CCTV Cameras, heaters and other video
accessories.
R2416UL
• Sixteen (16) fuse protected outputs.
• Outputs are rated @ 3.5 amp.
R2416ULCB
• Sixteen (16) Class 2 Rated PTC
protected power limited outputs.
• Outputs are rated @ 2.5 amp.
Specifications
• 24VAC @ 7 amp (170VA) or
28VAC @ 6 amp (170VA) supply current.
• Input 115VAC, 50/60Hz, 3 amp.
• Surge suppression.
• Illuminated power disconnect circuit breaker
with manual reset.
• Removable terminal blocks w/locking screw flanges.
• 3-wire grounded line cord.
• Individual power LEDs.
• Spare fuse(s) provided (fuse protected model only).
• Unit maintains camera synchronization.
• Ease of installation saves time and eliminates
costly labor.
• 2U rack mount chassis for use in standard
EIA 19” rack.
• Product weight:
- R2416UL: 14.8 lbs.
- R2416ULCB: 15.7 lbs.
• Shipping weight:
- R2416UL: 15.8 lbs.
- R2416ULCB: 16.7 lbs.
Agency Approvals
UL Listed for Commercial CCTV Equipment
(UL 2044).
CUL Listed - CSA Standard C22.2 No.1-98,
Audio, Video and Similar Equipment.
Enclosure Dimensions
3.25"H x 19.125"W x 8.5"D
View from back
BACK
3.125"
32
N
P
31
N
P
30
N
P
29
N
P
28
N
P
27
N
P
26
N
P
25
N
P
24
N
P
23
N
P
22
N
P
21
N
P
20
N
P
N
19
P
N
18
P
N
17
P
N
16
P
N
15
P
N
14
P
N
17.625"
BOTTOM
8.5"
FACEPLATE
19.125"
.75"
View from front
Altronix Corp. - 140 58th Street, Brooklyn, NY 11220 • 718-567-8181 • 888-258-7669 • altronix.com
13
P
N
12
P
N
11
P
N
10
P
N
9
P
N
8
P
N
7
P
N
6
P
N
5
P
N
4
P
N
3
P
N
2
P
N
1
P
Data Sheet
Cisco Catalyst 2955 Series Switches
®
®
Cisco Catalyst 2955 Series Switches are industrial-grade switching products that
provide wire-speed Fast Ethernet and Gigabit Ethernet connectivity for deployment in
harsh environments. The Cisco Catalyst 2955 Series operates in environments such as
industrial networking solutions (industrial Ethernet deployments), intelligent transportation
systems (ITS), and transportation network solutions. It integrates into military equipment,
Supervisory Control and Data Acquisition (SCADA) systems, power generation systems,
waste water treatment facilities, building automation systems, warehouses, and any other
facilities or applications where the environmental conditions or suspended solid
concentrations exceed the specifications of other commercial switching products.
The Cisco Catalyst 2955 Series uses industrial-grade components, a compact form
factor, convection cooling, and relay output signaling to extend intelligent services such as
enhanced security, high availability, and advanced quality of service (QoS) to areas that
cannot be served by traditional commercial-grade Ethernet switches.
Embedded in all Cisco Catalyst 2955 Series Switches is the Cisco Device Manager software,
which allows users to easily configure and monitor the switch using a standard Web browser,
eliminating the need for more complex terminal emulation programs and knowledge of the
command-line interface (CLI). Customers can easily initialize the switch with Web-based Cisco
Express Setup, without using the CLI. In addition, with Cisco Network Assistant, a standalone
network management application, customers can simultaneously configure and troubleshoot
multiple Cisco Catalyst desktop switches. Cisco Device Manager, Cisco Express Setup, and
Cisco Network Assistant reduce the cost of deployment by enabling less-skilled personnel to
set up switches quickly. Furthermore, Cisco Catalyst 2955 Series Switches provide extensive
management tools using Simple Network Management Protocol (SNMP) network management
platforms such as CiscoWorks.
®
This product line offers Cisco IOS Software functionality for traditional data, video, and voice
services, with enhanced intelligent services features for additional security, advanced QoS, and
high availability. Intelligent services are critical in supporting the reliability and determinism of
proprietary Layer 2 solutions typical of industrial Ethernet deployments, while providing the
advantages (standardization, open connectivity, bandwidth, integration, etc.) of an advanced
Ethernet switching architecture. These intelligent services include Layers 2-4 traffic prioritization,
rate limiting, and security filtering, helping to ensure the high uptime, low latency, deterministic
performance, and data integrity critical for industrial automation control networks.
Cisco Catalyst 2955 Series Switches consist of the following devices:
●
Cisco Catalyst 2955T-12—Twelve 10/100 ports and two fixed 10/100/1000BASE-T uplink
ports
●
Cisco Catalyst 2955C-12—Twelve 10/100 ports and two fixed 100BASE-FX multimode
uplink ports
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 1 of 15
Data Sheet
●
Cisco Catalyst 2955S-12—Twelve 10/100 ports and two fixed 100BASE-LX single-mode
uplink ports
Intelligence in the New Ethernet Networks
Currently, non-Ethernet Layer 2 networks are evolving from traditional field buses or proprietary
technologies to standards-based Ethernet networks. The progression to Ethernet is driven by a
multitude of factors, including:
●
Standardization—There are hundreds of millions of Ethernet devices around the world;
Ethernet has become the prevalent Layer 2 technology based on widely adopted
standards.
●
IP Connectivity—Ethernet is the most ubiquitous Layer 2 technology for Internet
connectivity, in turn providing unprecedented communications potential to networks that
have been traditionally isolated.
●
Bandwidth—Orders of magnitude above other existing technologies, Ethernet takes
advantage of the increased computational power of the new network hosts (I/O devices,
motion machinery, sensors, intelligent electronic devices, etc.) being deployed today. This
allows for real-time control and data gathering for a multitude of applications that were not
previously feasible, including preventive maintenance, total quality control monitoring,
remote monitoring, and asset management and optimization.
●
Multiple services on a single infrastructure—Intelligent Ethernet allows a single network
to carry multiple vendor implementations of control (EtherNet/IP, Modbus TCP, Foundation
Fieldbus High Speed Ethernet [HSE] and various Advanced Traffic Management Systems
[ATMSs]), and to use the same investment to also deliver traditional voice (telephony), data
(e-mail, technical support, and browsing), and video services (video monitoring).
●
Multilayer Integration—All of the elements described above allow for the integration of
higher-level applications such as enterprise resource planning (ERP), manufacturing
execution systems (MES), and advanced traffic management systems to the floor control
layer (programmable logic controllers [PLCs], PC-based control systems, traffic control
equipment, and human-machine interfaces [HMIs]). This allows for a true flow of data and
automation from the demand side (customer placing and order) to the factory floor
(assembly line) or from the monitoring devices in a freeway all the way to the emergency
response systems, as well as real-time control in SCADA applications. As organizations
increasingly rely on Ethernet networks, it is important to help ensure high availability,
security, scalability, and control. By adding Cisco IOS Software functionality to new network
applications, users can now deploy network-wide intelligent services that address these
requirements in a consistent way—from the I/O or monitoring device to the core and
through the WAN.
Network Security through Advanced Security Features
Cisco Catalyst 2955 Series Switches offer enhanced data security through numerous security
features. These features allow customers to enhance network security with capabilities to secure
traffic through the protection of passwords and configuration information; to provide options for
network security based on users, ports, and Media Access Control (MAC) addresses; and to
enable more immediate reactions to intruder and hacker detection.
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 2 of 15
Data Sheet
Secure Shell (SSH) Protocol and SNMPv3 protect information from tampering or eavesdropping
by encrypting information being passed along the network, thereby guarding administrative
information. Private VLAN Edge isolates ports on a switch, helping ensure that traffic travels
directly from the entry point to the aggregation device through a virtual path and cannot be
directed to another port.
Port-based access control parameters (ACPs) restrict sensitive portions of the network by
denying packets based on source and destination MAC addresses, IP addresses, or Transmission
Control Protocol/User Datagram Protocol (TCP/UDP) ports. ACP lookups are done in hardware,
so forwarding performance is not compromised when implementing this type of security in the
network. In addition, time-based ACPs allow configuration of differentiated services based on
time periods. ACPs can also be applied to filter traffic based on differentiated services code point
(DSCP) values. Port security provides another means to help ensure that appropriate users are on
the network, by limiting access based on MAC addresses.
For authentication of users with a Terminal Access Controller Access Control System (TACACS+)
or RADIUS server, 802.1x provides port-level security. 802.1x in conjunction with a RADIUS
server allows for dynamic port-based user authentication. 802.1x-based user authentication can
be extended to dynamically assign a virtual LAN (VLAN) based on a specific user, regardless of
where that user connects on the network. This intelligent adaptability provides greater flexibility
and mobility to the network's stratified user populations. By combining access control and user
profiles with secure network connectivity, services, and applications, customers can more
effectively manage user mobility and drastically reduce the overhead associated with
granting and managing access to network resources.
With multilayer Cisco Catalyst 2955 Series Switches, network managers can implement high
levels of console security. Multilevel access security on the switch console and a Web-based
management interface prevent unauthorized users from accessing or altering switch
configurations. TACACS+ or RADIUS authentication enable centralized access control of the
switch and restrict unauthorized users from altering the configuration. Deploying security can be
done through Cisco Network Assistant security wizards, which ease the deployment of security
features that restrict user access to a server, a portion of the network, or the entire network.
Network Control through Advanced QoS and Rate Limiting
Cisco Catalyst 2955 Series Switches offer superior and highly granular QoS based on Layers 2–4
information, to help ensure that network traffic is classified and prioritized, and that congestion is
avoided in the best possible manner. These switches can classify, reclassify, police (determine if
the packet is in or out of predetermined profiles and affect actions on the packet), and mark or
drop the incoming packets before the packet is placed in the shared buffer. Packet classification
allows the network elements to discriminate between various traffic flows and to enforce ratelimiting policies based on Layer 2 and Layer 3 QoS fields.
To implement QoS, these switches first identify traffic flows or packet groups. They classify or
reclassify these groups using the DSCP field in the IP packet and/or the 802.1p class of service
(CoS) field in the Ethernet packet. Classification and reclassification can also be based on criteria
as specific as the source or destination IP address, source or destination MAC address, or the
Layer 4 TCP/UDP ports. At the ingress (incoming port) level, Cisco Catalyst 2955 Series Switches
can also perform policing and marking of the packet.
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 3 of 15
Data Sheet
After the packet goes through classification, policing, and marking, it is assigned to the appropriate
queue before exiting the switch. Cisco Catalyst 2955 Series Switches support four egress
(outgoing port) queues per port, allowing the network administrator to be more discriminating and
specific in assigning priorities for the various applications on the network. At the egress level, the
switch performs scheduling—an algorithm that determines the order in which the queues are
processed. The switches support Weighted Round Robin (WRR) scheduling, strict priority queuing
or strict priority scheduling. The WRR scheduling algorithm helps ensure that lower-priority
packets are not entirely starved for bandwidth and are serviced without compromising the priority
settings administered by the network manager. Strict priority scheduling helps ensure that higherpriority packets will always get serviced first, ahead of other traffic in lower-priority queues.
These features allow for prioritization of mission-critical, such as motion-control traffic, critical I/O
or sensor data, video monitoring of security areas over voice (IP telephony traffic), ERP (Oracle,
SAP, etc.), and CAD/CAM, which, in turn, would be scheduled to have precedence over less timesensitive applications such as FTP or e-mail (SMTP). For example, it would be highly undesirable
to have a large file download destined to one port on a switch and have quality implications, such
as increased latency in industrial control traffic, destined to another port on the switch. This
condition is avoided by helping ensure that the control traffic is properly classified and prioritized
throughout the network. Other applications, such as Web browsing, can be treated as low priority
and handled on a best-efforts basis.
Cisco Catalyst 2955 Series Switches allocate bandwidth based on several criteria, including
MAC source address, MAC destination address, IP source address, IP destination address, and
TCP/UDP port number. Bandwidth allocation is essential in network environments that require
service-level agreements, or when it is necessary for the network manager to control the
bandwidth given to certain users. Cisco Catalyst 2955 Series Switches support up to six policers
per Fast Ethernet port and up to 60 policers on a Gigabit Ethernet port. This gives the network
administrator granular control of the network bandwidth.
Network Availability
To provide efficient use of resources for bandwidth-hungry applications like multicasts (common in
producer-consumer data distribution models), intelligent Cisco Catalyst 2955 Series Switches
support Internet Group Management Protocol (IGMP) snooping in hardware. Through the support
and configuration of IGMP snooping via Cisco Network Assistant, Cisco Catalyst 2955 Series
Switches deliver outstanding performance and ease of use in administering and managing
multicast applications on the LAN.
The IGMP snooping feature allows the switch to "listen in on" the IGMP conversation between
hosts. When a switch hears an "IGMP join" request from a host for a given multicast group, the
switch adds the host's port number to the group destination address (GDA) list for that group.
When the switch hears an "IGMP leave" request, it removes the host's port from the Content
Addressable Memory (CAM) table entry.
Per VLAN Spanning Tree Plus (PVST+) allows users to implement redundant uplinks while
distributing traffic loads across multiple links. This is not possible with standard Spanning-Tree
Protocol implementations. Cisco UplinkFast technology helps ensure immediate transfer to the
secondary uplink, a vast improvement over the traditional 30-to-60-second convergence time.
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 4 of 15
Data Sheet
Network Management
Customers can configure one switch at a time with the embedded Cisco Device Manager or
configure and troubleshoot multiple switches with Cisco Network Assistant, a standalone network
management software application optimized for LANs of small and medium-sized businesses with
up to 250 users. Cisco Device Manager offers a simple and intuitive GUI interface for configuring
and monitoring the switch. The software is Web-based and embedded in Cisco Catalyst 3750,
3650, 3550, 2970, 2960, 2955, 2950, and 2940 Series Switches. Cisco Device Manager reduces
the cost of deployment by enabling less-skilled personnel to quickly and simply set up switches.
Cisco Network Assistant software provides an integrated management interface for delivering
intelligent services, such as multilayer switching, QoS, multicast, and security ACLs. Cisco
Network Assistant software allows administrators make use of benefits formerly reserved for only
the most advanced networks without having to learn the CLI, or even the details of the technology.
With Cisco Network Assistant, customers can configure multiple ports and switches
simultaneously, perform software updates across multiple switches at once, and copy
configurations to other switches for rapid network deployments. Bandwidth graphs and link reports
provide useful diagnostic information, and the topology map gives network administrators a quick
view of the network status. Cisco Network Assistant supports a wide range of Cisco Catalyst
intelligent switches from Cisco Catalyst 2940 through Cisco Catalyst 4506. Through a user-friendly
GUI, users can configure and manage a wide array of switch functions and start the device
manager of Cisco routers and Cisco wireless access points.
The Cisco Network Assistant Software Guide Mode leads the user step by step through the
configuration of advanced features and provides enhanced online help for context-sensitive
assistance. Cisco AVVID (Architecture for Voice, Video and Integrated Data) wizards provide
automated configuration of the switch to optimally support video streaming or videoconferencing,
voice over IP (VoIP), and mission-critical applications. In addition, Smartports offers a set of
verified feature macros per connection type in an easy-to-apply manner. With these macros,
users can consistently and reliably configure essential security, availability, quality of service,
and manageability features recommended for Cisco Business-Ready Campus solutions with
minimal effort and expertise. These wizards and Smartports can save hours of time for network
administrators, eliminate human errors, and help ensure that the configuration of the switch is
optimized for these applications.
In addition to Cisco Network Assistant software, Cisco Catalyst 2955 Series Switches provide
extensive management tools using SNMP network management platforms such as CiscoWorks.
Managed with CiscoWorks, Cisco Catalyst switches can be configured and managed to deliver
end-to-end device, VLAN, traffic, and policy management. Coupled with CiscoWorks, Cisco
Resource Manager Essentials, a Web-based management tool, offers automated inventory
collection, software deployment, easy tracking of network changes, views into device
availability, and quick isolation of error conditions.
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 5 of 15
Data Sheet
Enhanced Hardware Features
The Cisco Catalyst 2955 Switch has been designed for deployment in harsh environments.
Through the use of special thermal design techniques and industrial-rated components, the
Cisco Catalyst 2955 is rated to operate at extreme temperatures (-40° to 60° C; -40° to 140° F).
Robust mechanical specifications allow for its deployment as a mobile platform and under extreme
vibration and shock environments (50G trapezoidal shock pulse). The compact form factor, DIN
rail mounting, and dual cabling orientations facilitate its deployment into industrial enclosures,
traffic control cabinets, and transportation vehicles. Two normally open relays can be associated
with the different port alarms, power alarms, and high temperature conditions to send an output
signal to other external mechanisms (visible or audible alarms, for example), HMIs, or PLCs for a
controlled shutdown. Dual power inputs provide for optional redundant power supplies,
guaranteeing an even higher level of resiliency and reliability.
Figure 1.
Cisco Catalyst 2955 Series Switches
Table 1.
Product Features and Benefits
Feature
Benefit
Availability
Superior redundancy for fault
backup
● IEEE 802.1D Spanning-Tree Protocol support for redundant backbone
connections and loop-free networks simplifies network configuration and
improves fault tolerance.
● Support for Cisco Spanning-Tree Protocol enhancements such as UplinkFast,
BackboneFast, and PortFast technologies helps ensure quick failover
recovery, enhancing overall network stability and availability.
● IEEE 802.1w Rapid Spanning-Tree Protocol (RSTP) provides rapid
convergence of the spanning tree, independent of spanning tree timers.
● Per VLAN Rapid Spanning Tree (PVRST+) allows rapid spanning-tree
reconvergence on a per-VLAN spanning-tree basis, without requiring the
implementation of spanning-tree instances.
● Provides unidirectional link detection (UDLD) and Aggressive UDLD for
detecting and disabling unidirectional links on fiber-optic interfaces caused
by incorrect fiber-optic wiring or port faults.
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 6 of 15
Data Sheet
Feature
Integrated Cisco IOS Software
features for bandwidth optimization
Benefit
● Bandwidth aggregation of up to 4 Gbps (two ports full duplex) through Cisco
®
Gigabit EtherChannel technology and up to 1.6 Gbps (eight ports full duplex)
through Fast EtherChannel technology enhances fault tolerance and offers
higher-speed aggregated bandwidth between switches, to routers and
individual servers. Port Aggregation Protocol (PAgP) is available to simplify
configuration.
● VLAN1 minimization allows VLAN1 to be disabled on any individual VLAN
trunk link.
● Per-port broadcast, multicast, and unicast storm control prevents faulty end
stations from degrading overall system performance.
● Per virtual LAN (VLAN) Spanning Tree Plus (PVST+) allows for Layer 2 load
sharing on redundant links, to efficiently use the extra capacity inherent in a
redundant design.
● IEEE 802.1s Multiple Spanning Tree Protocol (MSTP) allows a spanning-tree
instance per VLAN, enabling Layer 2 load sharing on redundant links.
● VLAN Trunking Protocol (VTP) pruning limits bandwidth consumption on VTP
trunks by flooding broadcast traffic only on trunk links required to reach the
destination devices. Dynamic Trunking Protocol (DTP) enables dynamic trunk
configuration across all ports on the switch.
● Internet Group Management Protocol Version 3 (IGMPv3) snooping provides
for fast client joins and leaves of multicast streams and limits bandwidthintensive video traffic to only the requestors. Multicast VLAN Registration
MVR, IGMP filtering, and fast-join and immediate leave are available as
enhancements. The number of IGMP groups can be limited with IGMP
throttling. IGMP Snooping time can be adjusted to optimize the performance of
multicast data flows.
● MVR continuously sends multicast streams in a multicast VLAN while isolating
the streams from subscriber VLANs for bandwidth and security reasons.
● Supports additional frame formats: Ethernet II (tagged and untagged), 802.3
(SNAP encapsulated, tagged and untagged frames).
Security
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 7 of 15
Data Sheet
Feature
Network Security Features
Benefit
● Filtering of incoming traffic flows based on Layer 2, Layer 3, or Layer 4 ACPs
prevents unauthorized data flows.
◦
The following Layer 2 ACPs or a combination can be used for security
classification of incoming packets: source MAC address, destination MAC
address, and 16-bit Ethertype.
◦
The following Layer 3 and Layer 4 fields or a combination can be used for
security classification of incoming packets: source IP address, destination IP
address, TCP source or destination port number, UDP source, or
destination port number. ACLs can also be used to filter based on DSCP
values.
◦
Time-based ACLs allow configuration of differentiated services based on
time periods.
● Private VLAN edge provides security and isolation between ports on a switch,
helping ensure that voice traffic travels directly from its entry point to the
aggregation device through a virtual path and cannot be directed to a different
port.
● Support for the 802.1x standard allows users to be authenticated, regardless
of which LAN port they are accessing, and provides unique benefits to
customers who have a large base of mobile (wireless) users accessing the
network.
◦
IEEE 802.1x with VLAN assignment allows a dynamic VLAN assignment for
a specific user, regardless of where the user is connected.
◦
IEEE 802.1x with voice VLAN gives an IP phone access to the voice VLAN,
regardless of the authorized or unauthorized state of the port.
◦
IEEE 802.1x with port security authenticates the port and manages network
access for all MAC addresses, including the clients'.
◦
IEEE 802.1x with guest VLAN allows guests without 802.1x clients to have
limited network access on the guest VLAN.
● SSHv2 and SNMPv3 provide network security by encrypting administrator
traffic during Telnet and SNMP sessions. SSHv2 and the crypto version of
SNMPv3 require a special crypto software image because of U.S. export
restrictions.
● Port Security and unicast MAC filtering secure the access to a port based on
MAC addresses. The aging feature of port security removes the MAC address
from the switch after a specific time frame to allow another device to connect
to the same port. Unicast MAC filtering allows non-IP packets to be filtered as
well.
● With unknown unicast/multicast port blocking, the switch will not flood packets
with unknown destination MAC addresses to all Ethernet ports. Unknown
unicast/multicast port blocking disables flooding on a per-port basis.
● MAC address notification allows administrators to be notified of new users
added or removed from the network.
● Spanning-tree root guard (STRG) prevents edge devices not in the network
administrator's control from becoming Spanning-Tree Protocol root nodes.
● The Spanning-Tree Protocol PortFast/bridge protocol data unit (BPDU) guard
feature disables access ports with Spanning-Tree Protocol PortFast enabled
upon reception of a BPDU, and increases network reliability, manageability,
and security.
● Multilevel console access security prevents unauthorized users from altering
the switch configuration.
● TACACS+ and RADIUS authentication enables centralized control of the
switch and restricts unauthorized users from altering the configuration.
● The user-selectable address-learning mode simplifies configuration and
enhances security.
● Trusted Boundary provides the ability to trust the QoS priority settings if a
Cisco IP phone is present and to disable the trust setting if the IP phone is
removed, preventing a rogue user from overriding prioritization policies in the
network.
● IGMP Filtering provides multicast authentication by filtering out nonsubscribers
and limits the number of concurrent multicast streams available per port.
● Support for dynamic VLAN assignment through implementation of VLAN
Membership Policy Server (VMPS) client functionality provides flexibility in
assigning ports to VLANs. Dynamic VLAN enables fast assignment of IP
addresses.
● SPAN support of intrusion detection systems (IDSs) to monitor, repel, and
report network security violations.
● Cisco Network Assistant software security wizards ease the deployment of
security features for restricting user access to a server, a portion of the
network, or the network.
QoS
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 8 of 15
Data Sheet
Feature
Benefit
Overview
● The switches support the aggregate QoS model by enabling classification,
policing/metering, and marking functions on a per-port basis at ingress and
queuing/scheduling functions at egress.
● The switches support configuring QoS ACPs on all ports, using ACPs to help
ensure proper policing and marking on a per-packet basis. Up to four ACPs
per switch are supported in configuring either QoS ACPs or security filters.
● Automatic QoS (Auto-QoS) greatly simplifies the configuration of QoS in
voice-over-IP (VoIP) networks by issuing interface and global switch
commands that allow the detection of Cisco IP phones, the classification of
traffic, and egress queue configuration.
QoS Classification
Support at Ingress
● The switches support QoS classification of incoming packets for QoS flows
based on Layer 2, Layer 3, and Layer 4 fields.
● The following Layer 2 fields (or a combination) can be used for classifying
incoming packets to define QoS flows: source/destination MAC address or 16bit Ethertype.
● The switches support identification of traffic based on Layer 3 type of service
(ToS) field DSCP values.
● The following Layer 3 and Layer 4 fields (or a combination) can be used to
classify incoming packets to define QoS flows: source/destination IP address,
TCP source/destination port number, or UDP source/destination port number.
QoS metering/policing at ingress
● Support for metering/policing of incoming packets restricts incoming traffic
flows to a certain rate.
● The switches support up to six policers per Fast Ethernet port, and 60 policers
on a Gigabit Ethernet port.
● The switches offer granularity of traffic flows at 1 Mbps on Fast Ethernet ports,
and 8 Mbps on Gigabit Ethernet ports.
QoS marking at ingress
● The switches support marking and remarking packets based on the state of
policers/meters.
● The switches support marking and remarking based on the following
mappings: from DSCP to 802.1p, and from 802.1p to DSCP.
● The switches support 14 well-known and widely used DSCP values.
● The switches support classifying or reclassifying packets based on the default
DSCP per port, and support classification based on DSCP values in the ACL.
● The switches support classifying or reclassifying frames based on the default
802.1p value per port.
● The switches support 802.1p override at ingress.
QoS scheduling support at egress
● Four queues per egress port are supported in hardware.
● The WRR queuing algorithm helps ensure that low-priority queues are not
starved.
● Strict Priority Scheduling helps ensure that time-sensitive applications such as
voice always follow an expedited path through the switch fabric.
Sophisticated traffic management
● The switch offers the ability to limit data flows based on MAC source or
destination address, IP source or destination address, TCP/UDP port
numbers, or any combination of these fields.
● The switch offers the ability to manage data flows asynchronously upstream
and downstream from the end station or on the uplink.
Management
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 9 of 15
Data Sheet
Feature
Benefit
Superior manageability
● An embedded Remote Monitoring (RMON) software agent supports four
RMON groups (history, statistics, alarms, and events) for enhanced traffic
management, monitoring, and analysis.
● The switch supports all nine RMON groups through the use of a Cisco
®
SwitchProbe Analyzer Switched Port Analyzer (SPAN) port, permitting traffic
monitoring of a single port, a group of ports, or the entire switch from a single
network analyzer or RMON probe.
● A SPAN port monitors traffic of a single port from a single network analyzer or
RMON probe.
● Remote SPAN (RSPAN) allows network administrators to locally monitor ports
in a Layer 2 switch network from any other switch in the same network.
● DHCP Snooping Option 82 enables more sophisticated IP address
assignment by the DHCP server.
● The Domain Name System (DNS) provides IP address resolution with userdefined device names.
● Trivial File Transfer Protocol (TFTP) reduces the cost of administering
software upgrades by downloading from a centralized location.
● Network Timing Protocol (NTP) provides an accurate and consistent
timestamp to all switches within the intranet.
● Layer 2 traceroute eases troubleshooting by identifying the physical path that a
packet takes from the source device to a destination device.
● Crash Information Support enables the switch to generate a crash file for
improved troubleshooting.
● Show Interface Capabilities provides information on the configuration
capabilities of any interface.
● RTTMON-MIB allows users to monitor network performance between a Cisco
Catalyst switch and a remote device.
Cisco Network Assistant software
● Cisco Network Assistant software is free, standalone network management
application software that simplifies the administration of networks of up to 250
users. It supports a wide range of Cisco Catalyst intelligent switches from
Cisco Catalyst 2940 through Cisco Catalyst 4506. With Cisco Network
Assistant, users can manage Cisco Catalyst switches plus launch the device
®
managers of Cisco integrated services routers (ISRs) and Cisco Aironet
WLAN access points by simply clicking their icon in the topology map.
● Cisco AVVID wizards use just a few user inputs to automatically configure the
switch to optimally handle different types of traffic: voice, video, multicast,
and/or high-priority data.
● A security wizard is provided to restrict unauthorized access to servers and
networks and to restrict certain applications on the network.
● One-click software upgrades can be performed across multiple switches
simultaneously, and configuration cloning enables rapid deployment of
networks.
● Cisco Network Assistant software supports multilayer feature configurations
such as ACPs and QoS parameters.
● Cisco Network Assistant Software Guide Mode assists users in the
configuration of powerful advanced features by providing step-by-step
instructions.
● Cisco Network Assistant software provides enhanced online help for contextsensitive assistance.
● Easy-to-use GUI provides both a topology map and front-panel view of the
switches.
● Multidevice and multiport configuration capabilities allow network
administrators to save time by configuring features across multiple switches
and ports simultaneously.
● User-personalized interface allows users to modify polling intervals, table
views, and other settings within Cisco Network Assistant software and to retain
these settings the next time they use Cisco Network Assistant.
● Alarm notification provides automated e-mail notification of network errors and
alarm thresholds.
Support for CiscoWorks
● Manageable through CiscoWorks network management software on a per-port
and per-switch basis, providing a common management interface for Cisco
routers, switches, and hubs.
● SNMPv1, v2, and v3 (non-crypto) and Telnet interface support deliver
comprehensive in-band management, and a CLI-based management console
provides detailed out-of-band management.
● Cisco Discovery Protocol versions 1 and 2 enable a CiscoWorks network
management station to automatically discover the switch in a network
topology.
● CiscoWorks is supported by the CiscoWorks 2000 LAN Management
Solution.
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 10 of 15
Data Sheet
Feature
Ease of use and
ease of deployment
Benefit
● Cisco Device Manager is embedded Web-based software that allows the
customer to easily configure and troubleshoot the switch, eliminating the need
for more complex terminal emulation programs and CLI knowledge, and
reducing the cost of deployment by enabling less-skilled personnel to quickly
and simply set up switches.
● Smartports offers a set of verified feature macros per connection type in an
easy-to-apply manner. With these macros, users can consistently and reliably
configure essential security, availability, quality of service, and manageability
features recommended for Cisco Business-Ready Campus solutions with
minimal effort and expertise.
● Autoconfiguration eases the deployment of switches in the network by
automatically configuring multiple switches across a network via a boot server.
● Autosensing on each Ethernet port] detects the speed of the attached device
and automatically configures the port for 10-, 100-, or 1000-Mbps operation,
easing the deployment of the switch in mixed 10, 100, and 1000BASE-T
environments.
● Autonegotiating on all ports automatically selects half- or full-duplex
transmission mode to optimize bandwidth.
● Cisco VTP supports dynamic VLANs and dynamic trunk configuration across
all switches.
● DTP enables dynamic trunk configuration across all ports in the switch.
● Voice VLAN simplifies telephony installations by keeping voice traffic on a
separate VLAN for easier network administration and troubleshooting.
● Dynamic Trunking Protocol (DTP) enables dynamic trunk configuration across
all ports on the switch.
● PAgP automates the creation of Cisco Fast EtherChannel or Gigabit
EtherChannel groups, enabling linking to another switch, router, or server.
● Link Aggregation Control Protocol (LACP) allows the creation of Ethernet
channeling with devices that conform to IEEE 802.3ad. This is similar to Cisco
EtherChannel and PAgP.
● The default configuration stored in Flash helps ensure that the switch can be
quickly connected to the network and can pass traffic with minimal user
intervention.
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 11 of 15
Data Sheet
Table 2.
Product Specifications
Feature
Performance
Description
● 13.6 Gbps switching fabric
● Cisco Catalyst 2955T-12: 6.4 Gbps maximum forwarding bandwidth
● Cisco Catalyst 2955C-12: 2.8 Gbps maximum forwarding bandwidth
● Cisco Catalyst 2955S-12: 2.8 Gbps maximum forwarding bandwidth
● (Forwarding rates based on 64-byte packets)
● Cisco Catalyst 2955T-12: 4.8 Mpps wire speed forwarding rate
● Cisco Catalyst 2955C-12: 2.0 Mpps wire speed forwarding rate
● Cisco Catalyst 2955S-12: 2.0 Mpps wire speed forwarding rate
● 8 MB memory architecture shared by all ports
● Up to 32 MB SDRAM and 16 MB Flash memory
● Configurable up to 8000 MAC addresses
Management
● BRIDGE-MIB
● CISCO-ACCESS-ENVMON-MIB
● CISCO-BULK-FILE-MIB
● CISCO-C2900-MIB
● CISCO-CDP-MIB
● CISCO-CLUSTER-MIB
● CISCO-CONFIG-MAN-MIB
● CISCO-ENTITY-ALARM-MIB
● CISCO-ENTITY-MIB
● CISCO-ENVMON-MIB
● CISCO-FLASH-MIB
● CISCO-FTP-CLIENT-MIB
● CISCO-HSRP-MIB
● CISCO-IGMP-FILTER-MIB
● CISCO-IMAGE-MIB
● CISCO-LAG-MIB
● CISCO-MAC-NOTIFICATION-MIB
● CISCO-MEMORY-POOL-MIB
● CISCO-PAE-MIB
● CISCO-PAGP-MIB
● CISCO-PORT-SECURITY-MIB
● CISCO-PRIVATE-VLAN-MIB
● CISCO-PROCESS-MIB
● CISCO-PRODUCTS-MIB
● CISCO-RTTMON-MIB
● CISCO-STACKMAKER-MIB
● CISCO-STP-EXTENSIONS-MIB
● CISCO-SYSLOG-MIB
● CISCO-TCP-MIB
● CISCO-VLAN-MEMBERSHIP-MIB
● CISCO-VTP-MIB
● ENTITY-MIB
● ETHERLIKE-MIB
● HC-RMON-MIB
● IEEE8021-PAE-MIB
● IEEE8023-LAG-MIB
● IF-MIB
● IP-MIB
● OLD-CISCO-CPU-MIB
● OLD-CISCO-FLASH-MIB
● OLD-CISCO-INTERFACES-MIB
● OLD-CISCO-IP-MIB
● OLD-CISCO-MEMORY-MIB
● OLD-CISCO-SYSTEM-MIB
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 12 of 15
Data Sheet
Feature
Description
● OLD-CISCO-TS-MIB
● RFC1213-MIB
● RFC1398-MIB
● RMON-MIB
● RMON2-MIB
● SMON-MIB
● SNMP-FRAMEWORK-MIB
● SNMP-MPD-MIB
● SNMP-TARGET-MIB
● SNMPv2-MIB
● TCP-MIB
● UDP-MIB
Standards
● IEEE 802.1x support
● IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
● IEEE 802.1s Multiple Spanning Tree Protocol (MSTP)
● IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and 1000BASE-T ports
● IEEE 802.1D Spanning-Tree Protocol
● IEEE 802.1p CoS prioritization
● IEEE 802.1Q VLAN
● IEEE 802.3 10BASE-T specification
● IEEE 802.3u 100BASE-TX specification
● IEEE 802.3ab 1000BASE-T specification
● IEEE 802.3ad Link Aggregation Control Protocol (LACP)
● IEEE 802.3ah Ethernet in the First Mile (EFM)
● RMON I and II standards
● SNMPv1, SNMPv2c, and SNMPv3
Connectors and cabling
● 10BASE-T/100BASE-TX ports: RJ-45 connectors; four-pair Category 5 UTP
cabling
● 1000BASE-T ports: RJ-45 connectors; four-pair Category 5 UTP cabling
● 100BASE-FX ports: MT-RJ connectors; 50/125 or 62.5/125 micron multimode fiberoptic cabling
● 100BASE-LX ports: LC connectors; 9/125 micron single-mode fiber-optic cabling
● Management console port: 8-pin RJ-45 connector, RJ-45-to-RJ-45 rollover cable
with RJ-45-to-DB9 adapter for PC connections; for terminal connections, use RJ45-to-DB25 female data-terminal-equipment (DTE) adapter (can be ordered
separately from Cisco, part number ACS-DSBUASYN=)
MT-RJ patch cables for
Cisco Catalyst 2955
Type of cable, Cisco part number
● One-meter, MT-RJ-to-SC multimode cable, CAB-MTRJ-SC-MM-1M
● Three-meter, MT-RJ-to-SC multimode cable, CAB-MTRJ-SC-MM-3M
● Five-meter, MT-RJ-to-SC multimode cable, CAB-MTRJ-SC-MM-5M
● One-meter, MT-RJ-to-ST multimode cable, CAB-MTRJ-ST-MM-1M
● Three-meter, MT-RJ-to-ST multimode cable, CAB-MTRJ-ST-MM-3M
● Five-meter, MT-RJ-to-ST multimode cable, CAB-MTRJ-ST-MM-5M
● Two-meter, LC to SC single-mode cable, CAB-CP-LCSC-2M
Indicators
● Per-port status LEDs: Link integrity, disabled, activity, and indications
● Dual-power-supply indicators
● Major and minor alarm-relay indicators
Dimensions and weight
(HxWxD)
● 3.78x8.07x5.03 in. (9.60x20.50x12.78 cm): Connectors facing forward
● 5.03x8.07x3.78 in. (12.78x20.50x9.60 cm): Connectors facing downward
● 3.0 lb (1.4 kg)
Relay contacts
● Surge withstand between open contacts: 1500V, FCC Part 68
● Surge withstand between contact and coil: 2500V, Bellcore
● Maximum switching capacity: 1A @ 30 VDC
● Maximum switching voltage: .3A @ 125 VAC
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 13 of 15
Data Sheet
Feature
Environmental ranges
Description
● Recommended operating temperature range: -40° to 140 ° F (-40° to 60° C)
● Recommended storage temperature range: -40° to 185° F (-40° to 85° C)
● Operating relative humidity: 10 to 95% (noncondensing)
● Operating altitude: 9843 ft (3000 m) @ 104° F (40° C)
● Storage altitude: Up to 29,500 ft (9000 m)
● Shock: 50 g trapezoidal shock (meets or exceeds ASTM D3332)
● Vibration: 500 Hz (meets or exceeds MIL-STD-810, Method 514.5)
Power requirements
● External 24V (dual-redundant DC input, screw-down connectors)
● Power consumption: 23W maximum, 78.53 BTU/hour
● 18V minimum; 32V maximum
Predicted mean time
between failure (MTBF)
● WS-C2955T 235,022 hours
● WS-C2955C 206,378 hours
● WS-C2955S 205,115 hours
● Telcordia SR-332 Gf
Fiber port specifications
● 100BASE-FX (MT-RJ connectors @ 1,300 nm):
● Optical receiver sensitivity: -30 dBm
● Optical transmitter power: -19 to -14 dBm
● Maximum distance: 2 km
● 100BASE-LX (LC connectors @ 1,300 nm):
● Optical receiver sensitivity: -38 to -31 dBm
● Optical transmitter power: -15 to -8 dBm
● Maximum distance: 15 km
Regulatory Agency Approvals
Safety certifications
Hazardous locations
● CE Marking
● UL 60950
● CSA 22.2/60950
● TUV GS: CB Report to IEC 60950
● UL 508
● CSA 22.2/142
● AS/NZS 3260
● NOM
● UL 1604—Class I, Div 2 Group A, B, C, D
● CSA 22.2/213—Class 1, Div 2 Group A, B, C, D
● EN 50021—Class I, Zone 2
Electromagnetic emissions
certifications
● FCC Part 15 Class A
● ICES-003 Class A
● EN 55022: (CISPR22 Class A)
● EN 55024: (CISPR24)
● VCCI Class A
● AS/NZS CISPR 22 Class A
● VCCI Class 1
● CE Marking
● CNS 13438
● BSMI Class A
● MIC Class A
● EN 61131-2
● EN 55011 (CISPR 11) Class A
ITS
NEMA TS-2
Warranty
Limited five-year warranty
External DIN Rail Mountable Power Supply
Input voltage
AC100-120/220-240V (switchable) 47-63 Hz
Input current
<1.3A (switch in 115V position)
Input current
<0.7A (switch in 230V position)
Output voltage
24 VDC (+5%, -1%)
Size (WxHxD)
1.92x4.92x4.05 (50x125x103 mm)
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 14 of 15
Data Sheet
Feature
Description
Weight
1 lb (460 g)
Worldwide approvals
UL, EN, CSA, and CB
Overload protection
Over 1.5 times normal current
Cooling
Normal convection cooling
Temperature range
● -25º to +85ºC (storage)
● -10º to +60ºC (operating)
Service and Support
The service and support programs described in Table 3 are available as part of the Cisco Desktop
Switching Service and Support solution, and are available directly from Cisco and through
resellers.
Table 3.
Cisco Service and Support Programs
Service and Support
Features
Benefits
Advanced Services
Total Implementation Solutions
(TIS)—available direct from Cisco
Packaged Total Implementation
Solutions (Packaged TIS)—available
through resellers
● Project management
● Site survey and configuration
deployment
● Installation, text, and cutover
● Supplements existing staff
● Helps ensure that functionality
meets customer needs
● Mitigates risk
● Training
● Major moves, adds, or changes
● Design review and product staging
Technical Support Services
®
Cisco SMARTnet and SMARTnet
Onsite—available direct from Cisco
Packaged SMARTnet—available
through resellers
Table 4.
● 24x7 access to software updates
● Web access to technical
repositories
● Telephone support through the
Technical Assistance Center
● Advance replacement of hardware
parts
● Enables proactive or expedited
issue resolution
● Lowers cost of ownership by
using Cisco expertise and
knowledge
● Minimizes network downtime
Ordering Information
Model Numbers
Configuration
WS-C2955T-12
Twelve 10/100 ports and two 10/100/1000BASE-T ports
WS-C2955C-12
Twelve 10/100 ports and two 100BASE-FX ports
WS-C2955S-12
Twelve 10/100 ports and two 100BASE-LX ports
PWR-2955-AC=
DIN Rail mountable 24V power supply (85 to 264 VAC, or 90 to 375VDC input)
STK-RACKMNT-2955=
DIN Rail Adapter for 19" rack mounting
For More Information on Cisco Products
●
United States and Canada: 800 553-NETS (6387)
●
Europe: 32 2 778 4242
●
Australia: 612 9935 4107
●
Other: 408 526-7209
●
http://www.cisco.com
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 15 of 15
Data Sheet
Printed in USA
All contents are Copyright © 1992–2006 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
C78-380621-00 11/06
Page 16 of 15
D7100 SERIES
10/100 Mbps ETHERNET OPTICAL TRANSCEIVER
PRODUCT SPECIFICATION
FEATURES
• 10/100 Mbps Ethernet
- Auto-Negotiating
- 10/100 Selectable
- Full Duplex or Half Duplex Data
D
• Auto Network Detection MDI/MDI-X
• Distances up to 45 km (28 miles)
• NTCIP Compatible
DESCRIPTION
The IFS D7100 Series ethernet transceiver is designed to transmit
and receive 10 or 100 Mbps data over multimode or singlemode
fiber. The IFS D7100 Series will function as a 10 Mbps Ethernet
link, or as a 100 Mbps Ethernet link without any adjustments. The
D7100 Series is environmentally hardened to operate in extreme
temperatures. Status indicating LED’s for power and data type are
present at the RJ-45 connector and at the fiber optic transceiver end.
Plug-and-play design ensures ease of installation requiring no
electrical or optical adjustments. The modules are available in
either stand-alone or rack mount versions.
• Tested and Certified by an Independent Testing Laboratory for
Full Compliance with the Environmental Requirements (Ambient
Operating Temperature, Mechanical Shock, Vibration, Humidity
with Condensation, High-Line/Low-Line Voltage Conditions and
Transient Voltage Protection) of NEMA TS-1/TS-2 and the Caltrans
Specification for Traffic Signal Control Equipment.
• Multimode and Singlemode Versions Available
• ST Optical Connectors Standard
• No In-field Electrical or Optical Adjustments Required
• Power, Transmit and Receive Data Status LED Indicators
Available at:
• Hot-Swappable Rack Modules
www.
APPLICATION EXAMPLES
• IEEE 802.3 Compliant
• 10/100 Mbps Ethernet
• High Speed Computer Links
• Comprehensive Lifetime Warranty
.com
• A & E Specifications, (CSI)
• AutoCAD Drawings
• Operation Manuals
• Technical Bulletins
ORDERING INFORMATION
PART
NUMBER
MULTIMODE
62.5/125µm**
DESCRIPTION
D7120
D7120WDMA❖
D7120WDMB
❖
SINGLEMODE D7130WDMA
D7130WDMB
9/125µm
ACCESSORIES♦
OPTIONS
FIBERS
REQUIRED
OPTICAL
PWR BUDGET
MAX.
DISTANCE*
10/100 Mbps Ethernet (1310 nm)
2
10 dB
1.2 miles (2 km)
10/100 Mbps Ethernet (1310/1550 nm)
10/100 Mbps Ethernet (1550/1310 nm)
1
10 dB
3 miles (5 km)
10/100 Mbps Ethernet (1310/1550 nm)
10/100 Mbps Ethernet (1550/1310 nm)
1
15 dB
28 miles (45 km)
PS-12VDC 12 Volt DC Plug-in Power Supply (Included)
PS-12VDC-230 12 Volt DC Plug-in Power Supply, 230 VAC Input (Included if specified at time of order)
Add ‘-R3’ to Model Number for R3 Rack Mount (Requires R3 Rack purchased separately)
Add ‘-C’ for Conformally Coated Printed Circuit Boards (Extra charge, consult factory)
* Optical transmission distance is limited to optical loss of the fiber and any additional loss introduced by connectors, splices and patch panels.
Distance can also be limited by fiber bandwidth. **For 50/125 Fiber, subtract 4 dB from Optical Power Budget. ❖ WDMA must mate with a WDMB.
♦ All accessories are third party manufactured.
International Fiber Systems, Incorporated ■ DESIGN CENTER (888) 999-9IFS or (203) 426-1180
FAX (203) 426-3326 ■ sales@ifs.com ■ For an office near you go to: www.ifs.com
With Offices in Asia Pacific ■ Australia ■ Europe ■ Latin America
D7100 SERIES
10/100 Mbps ETHERNET OPTICAL TRANSCEIVER
TECHNICAL SPECIFICATION
SPECIFICATIONS
ELECTRICAL & MECHANICAL
Ethernet
10/100 Mbps
IEEE 802.3 Compliant
Full Duplex or Half Duplex
Power:
Surface Mount:
Rack:
Number of Rack Slots:
Voltage Regulation:
Current Protection:
D7120
D7120WDM
D7130WDM
1310 nm, Multimode
1310/1550 nm, Multimode
1310/1550 nm, Singlemode
Circuit Board:
Size (in./ cm.) (LxWxH):
Surface Mount:
Rack Mount:
Shipping Weight:
NUMBER OF FIBERS
1 or 2
ENVIRONMENTAL
DATA
Data Interface:
Data Rate:
WAVELENGTH
7.0 x 4.9 x 1.0 in., 17.8 x 12.5 x 2.5 cm.
7.7 x 5.0 x 2.0 in., 19.6 x 12.7 x 5 cm
< 2 lbs./0.9 kg
MTBF:
Operating Temp:
Storage Temp:
Relative Humidity:
CONNECTORS
Optical:
Power:
Data:
12 VDC @200 mA
From Rack
2
Solid-state; independent on each board
Automatic Resettable Solid-State Current
Limiters
Meets IPC Standard
ST
Terminal Plug with screw clamps
RJ-45
>100,000 hours
-40° C to +74° C
-40° C to +85° C
0% to 95% (non-condensing)†
† May be extended to condensation conditions by adding suffix ‘–C’ to model
number for conformal coating.
AGENCY COMPLIANCE
Federal Supply Schedule
MADE IN THE USA
Contract No. GS-07F-0049M
Complies with FDA Performance Standard for Laser Products,
Title 21, Code of Federal Regulations, Subchapter J
OPTICAL POWER BUDGET
FIBER
Multimode
62.5/125µm**
Singlemode
9/125µm
WAVELENGTH
TRANSCEIVER
MODEL
OPTICAL
PWR BUDGET
MAX.
DISTANCE*
1310 nm
D7120
10 dB
1.2 miles (2 km)
1310/1550 nm
D7120WDMA (1310/1550 nm)
D7120WDMB (1550/1300 nm)
10 dB
3 miles (5 km)
1310/1550 nm
D7130WDMA (1310/1550 nm)
D7130WDMB (1550/1310 nm)
15 dB
28 miles (45 km)
* Optical transmission distance is limited to optical loss of the fiber and any additional loss introduced by connectors, splices and patch panels.
Distance can also be limited by fiber bandwidth. **For 50/125 Fiber, subtract 4 dB from Optical Power Budget.
SYSTEM DESIGN
up to 1.2 miles
(2 km)
D7120
ifs
D7120
International
ifs
Fiber
Systems
Incorporated
International
Fiber
Systems
Incorporated
203.426.1180
203.426.1180
2 Fibers
62.5/125µm MM
TEL (203)426-1180 ■ FAX (203)426-3326 ■ www.ifs.com ■ sales@ifs.com
16 Commerce Road ■ Newtown, CT 06470
Due to our continued effort to advance technology, product specifications are subject to change without notice.
09/19/07
DES-3010PA Managed Layer 2 Fast Ethernet Switch
High-Performance Switching:
+ 5.6Gbps Switching Capacity
+ 8 Ports IEEE 802.3af PoE
+ 802.1s (Multiple Spanning Tree)
+ 802.3w (Rapid Spanning Tree)
+ Bandwidth Control down to 64k
+ 1 x 1000Base-T Port
+ 1 x SFP Slot
+ Small Footprint - 11” Chassis
+ Rackmountable
Network Management:
+ SSH/SSL
+ SNMP v1/2c/3
+ RMON (4 Groups)
+ Web GUI/CLI
+ Console
+ TACACS+ Authentication
+ RADIUS Client
PoE Power Management:
+ Port Status Monitoring
+ Fast Power Shutdown
+ GUI Power Status Monitoring
+ Auto PD Detection
+ PoE Status Counters & Alerts
Enterprise Features:
+ 802.1p Priority/QoS (4 Queues)
+ Priority-based on DSCP
+ 802.1x (Port & MAC Based
Authentication)
+ VLANs (Up to 256)
+ Guest VLAN
+ Private VLANs
+ Internal Power Supply
+ Redundant Power Supply (Optional)
8-Port 10/100Mbps PoE Switch, 1 x 1000BASE-T Port & 1 SFP
With a 5.6Gbps switching capacity and Power-over-Ethernet
(PoE) support, the DES-3010PA by D-Link® is a
high-performance, managed Layer 2 solution that provides
an ideal choice for workgroups and departments needing
advanced Layer 2 switching features in a small form factor,
11” chassis. The DES-3010PA is a great entry-level switch
for the SMB just starting out or the already established
business looking to bring a managed solution to the desktop.
The optional fiber uplink can provide connectivity for a
small group of users over a larger distance such as on an
educational or business campus. The DES-3010PA has eight
10/100Mbps ports and an SFP port for high-speed uplinks
to servers and/or backbones. The DES-3010PA is also
equipped with a copper 1000Base-T port for easy uplinks
to standard Gigabit copper switches. With support for
Power-over-Ethernet on all eight ports, the DES-3010PA
supports 802.3af-enabled access points, security cameras,
IP phones and more without requiring additional wiring.
VLANs, Bandwidth Control, and SNMP versions 1/2c/3. The
DES-3010PA also supports many of the features you would
expect to see on a larger managed solution such as IGMP
snooping, 802.3ad (Link Aggregation), 256 VLANs, support for
GVRP, traffic monitoring, SYSLOG, and more.
High-Performance Layer 2 Switching
The DES-3010PA includes advanced PoE power management
capabilities not found in unmanaged PoE solutions. These
features include individual port status monitoring, fast
power shutdown (in the case of power supply failure)
and voltage/current monitoring and regulation. Power
management determines the exact power draw per port
and balances each port’s PoE power output accordingly.
This allows the switch to power higher and lower wattage
devices according to user-definable parameters such as
maximum available power, port priority (critical, high, low),
and maximum allowable power per port. The DES-3010PA
provides the following power status and troubleshooting
statistics from an easy-to-read CLI and GUI anywhere in
the network: Powered Device (PD) classification, PD status,
power status monitoring (displaying power usage and
percent utilized), along with short and overload notification.
With a 5.6Gbps switching capacity, the DES-3010PA is a
wire-speed, high performance switch. It includes support for
Private VLANs (which protect privacy by isolating ports) and
Guest VLANs. Guest VLANs are useful when migrating end
users to an 802.1x environment when existing workstations
do not yet support the 802.1x protocol, and for delivering
limited services such as Internet access to un-authenticated
or short-term users. When deployed in a school campus,
bookstore, coffee house, or other retail establishment,
the DES-3010PA can be used in conjunction with wireless
access points to create a secure Internet Hot Spot. This
allows visitors to access special services or surf the Internet
completely isolated from sensitive internal network data. And
with the addition of up to 15.4 watts of PoE per port, powering
those wireless access points has never been easier.
Advanced Enterprise Features
The DES-3010PA brings advanced enterprise functions
to a more affordable level while supporting QoS/CoS
(based on 802.1p, Port, DSCP and ToS), rich security and
management features such as 802.1x port and MAC based
RADIUS and TACACS+ authentication, secure encrypted
management through both SSH and SSL, Guest and Private
IEEE 802.3af Power over Ethernet
The DES-3010PA provides eight 802.3af (PoE) ports and
supplies up to 15.4 watts per port for any 802.3af-compliant
device. The popularity of PoE-enabled switching devices
grows as more PoE-capable access points, IP phones, security
cameras, and PDA cradles hit the market. The difficulty and
cost often associated with running new AC power outlets to
hard-to-reach locations has made PoE an indespensable
technology for SMBs, schools, and Enterprise-class networks.
D-Link can even supply power and add PoE operability to nonPoE products with the DWL-P50 adapter.
Advanced Power Management
DES-3010PA Managed Layer 2 Fast Ethernet Switch
8-Port 10/100Mbps PoE Switch, 1 x 1000BASE-T Port & 1 SFP
Technical Specifications
Product Specifications
DES-3010PA
Managed 8-Port 10/100 PoE Switch with 1 1000BASE-T Port, 1 SFP Port
Switch Fabric
5.6Gbps
Transmission Method
Store-and-Forward
VLANs
Support up to 256 VLAN Groups
Priority Queues
4 Queues
Packet Buffer
128KB
Multicast Support
IGMP Snooping
Interface Options
RJ-45
10BASE-T, 100BASE-TX & 1000BASE-T
SFP/mini-GBICs
1000BASE-X support based on Type of SFP, LC
Network Management
In & Out of Band
Telnet, CLI/Console, RMON, Web-based HTTP, SNMPv1/2/3, Port Mirroring, SSH 2.0, SSL
Network Protocols and Standards
IEEE
802.3 Ethernet, 802.3u Fast Ethernet, 802.1D Spanning Tree, 802.1w Rapid Spanning Tree, 802.1s Multiple Spanning
Tree, 802.1p Priority Tags (4 queues), 802.3ad Link Aggregation Control (six 8-port groups), 802.3xFlow Control, 802.1x
(Port & MAC Based Network Access Control), 802.1Q VLANs (up to 256), Private VLANs, Guest VLANs, 802.3af
Power-over-Ethernet
IETF
RFC1757 RMON (4 Groups), RFC1493 Bridge, RFC1643 Ether-like MIB, RFC2358 ETHER LIKE_MIB, RFC2674
Additional Features
IGMP Snooping, Telnet, TFTP Client, BootP Client, DHCP Client, SNMP v1/2c/3, Rate Limiting down to 64k , QoS classification
based on ToS, Traffic Monitoring, MAC address browsing, Port Description, CPU Utilization Monitoring, SNTP, Radius
Authentication, TACACS+ Authentication, Auto-Negotiation, Port Mirroring, Broadcast Storm Control, SYSLOG, GVRP
Electrical & Emissions Summary
Emissions
FCC Class A, CE, VCCI
Power Supply
AC Input: 100 - 240 VAC, 50-60 Hz
PoE Power per Port
15.4 Watts Maximum
PoE Power Budget
110 Watts
Power Consumption
130 Watts Maximum
Heat Dissipation
444 BTU/hr Maximum
Safety Agency Certifications and Environmental
Safety
CuL
Temperature
Operating: Storage: 32 ~ 122°F (0 ~ 50°C)
14 ~ 158°F (-10 ~ 70°C)
Humidity
Operating: Storage: 10%-90% RH
5% ~ 90% RH
DES-3010PA Managed Layer 2 Fast Ethernet Switch
8-Port 10/100Mbps PoE Switch, 1 x 1000BASE-T Port & 1 SFP
Physical Specifications
Dimensions (Dx W x H)
7.1in x 11in x 1.7in (180.1mm x 279.4mm x 43.9mm)
Weight
4 lbs (1.8 kg)
Warranty Information
Warranty
Limited Lifetime1
Ordering Information
Part Number
Description
DES-3010PA
Managed 8-Port 10/100 PoE Switch with 1 1000BASE-T Port, 1 SFP Port
DES-3010PA-TAA
TAA compliant version of DES-3010PA
DEM-310GT
1000BASE-LX SFP/mini-GBIC Up to 10Km (singlemode)
DEM-311GT
1000BASE-SX SFP/mini-GBIC Up to 550m
DPS-510
Redundant Power Supply
Available only in the U.S.A. and Canada
1
All references to speed are for comparison purposes only. Product specifications, size and shape are subject to change without notice, and actual product
appearance may differ from that depicted herein. Specifications contained herein are based on Hardware version A1/A2/A3.
Hardware Version A1/A2/A3
D-Link Systems, Inc. 17595 Mt. Herrmann Street Fountain Valley CA 92708 www.dlink.com
©2005-2008 D-Link Corporation/D-Link Systems, Inc. All rights reserved. D-Link and the
D-Link logo are registered trademarks of D-Link Corporation or its subsidiaries in the
United States and other countries. Other trademarks or registered trademarks are the
property of their respective owners. Visit www.dlink.com for more details.
DATASHEET
AXIS 243Q Blade Video Server / AXIS 291 1U Video Server Rack
Full frame rate, high-density video encoder rack solution.
> Full frame rate
> High-density solution
> High-quality,
de-interlaced video
> Simultaneous
MPEG-4 and
Motion JPEG
> Video motion
detection and
pre-/post-alarm
buffer
> Support for PTZ and
dome cameras
AXIS 291 1U Video Server Rack is a high-density solution for seamless and professional
installation of video encoders. Together with the AXIS 243Q Blade Video Server, it is designed
to migrate analog systems to high performance, IP-based, digital solutions.
The powerful combination of AXIS 243Q and AXIS 291 1U
offers full frame rate at up to 4CIF resolutions on all
channels simultaneously.
Analog video is converted to high-quality, de-interlaced,
digital video.
Simultaneous Motion JPEG and MPEG-4 for optimized
quality and bandwidth.
The event management capabilities ensure efficient
use of the cameras in the network video system. This
includes video motion detection, active tampering alarm,
and alarm buffering.
The video server enables pan/tilt/zoom control over the
network of all leading brands of analog video cameras
on the market.
Technical specifications – AXIS 243Q Blade Video Server / 291 1U Video Server Rack
AXIS 243Q Blade Video Server
Requires the AXIS 201 1U Video Server Rack or the AXIS Q7900
Rack
MPEG-4 Part 2 (ISO/IEC 14496-2)
Motion JPEG
704x576 to 160x120
Operating
conditions
Approvals
Up to 30/25 (NTSC/PAL) per channel in all resolutions
Up to 30/25 (NTSC/PAL) per channel in all resolutions
Simultaneous MPEG-4 and Motion JPEG
Controllable frame rate and bandwidth
VBR/CBR MPEG-4
Compression, color
Rotation: 90°, 180°, 270°
Aspect ratio correction
Text and image overlay
Privacy mask
Deinterlace filter
Network
Security
Weight
System integration
Open API for software integration, including VAPIX®
Application
from Axis Communications available at www.axis.com
Programming
Interface
Intelligent video Video motion detection, active tampering alarm
Intelligent video, external inputs, video loss, on boot, PTZ preset
Alarm events
File upload via FTP, HTTP and email
Notification via email, HTTP and TCP
External output activation
9 MB pre- and post-alarm per channel
Pan/Tilt/Zoom
Metal casing for standalone or rack mounting
Power
100 – 240 V AC, 1.9 A max 80 W (with 3x243Q)
Connectors
Ethernet 10BASE-T/100BASE-TX/1000BASE-T, RJ-45 (Gigabit
Ethernet)
3 terminal blocks:
4 alarm inputs
4 outputs
RS-485/422 half-duplex
0 – 45 ºC (32 – 113 ºF)
Humidity 20 – 80% RH (non-condensing)
EN 55022 Class B, EN 61000-3-2, EN 61000-3-3, EN 55024,
EN 61000-6-1, EN 61000-6-2, FCC Part 15 Subpart B Class B,
VCCI Class B, AS/NZ CISPR 22, ICES-003, ITE, UL, cUL, EN
60950-1, CB-certificate, KTL
3.7 kg (8.2 lbs) excluding blades
Weight
Included
accessories
Wide range of analog PTZ cameras supported (drivers available
for download at www.axis.com)
20 presets/camera, guard tour, PTZ control queue
Supports Windows compatible joysticks
Installation Guide, mounting kit, AC power cable
More information is available at www.axis.com
321 mm (12.6”)
44.5 mm (1.8”)
31 mm (1.2”)
23.6 mm (0.9”)
2.5 mm (0.10”)
344.6 mm (13.6”)
2.5 mm (0.10”)
441 mm (17.4”)
482.6 mm (19.0”)
52.8 mm (2.1”)
23.6 mm (0.9”)
441 mm (17.4”)
482.6 mm (19.0”)
52.8 mm (2.1”)
44.5 mm (1.8”)
44.5 mm (1.8”)
2.5 mm (0.10”)
311.2 mm (12.3”)
182 mm (7.2”)
311.2 mm (12.3”)
182 mm (7.2”)
44.5 mm (1.8”)
Optional accessories
23.6 mm (0.9”)
Dimensions
441 mm (17.4”)
482.6 mm (19.0”)
Casing
Operating
conditions
Approvals
Alarm triggers
Video buffer
4 analog composite video BNC input, NTSC/PAL auto-sensing
RJ-45 10BASE-T/100BASE-TX
Terminal block for 4 inputs, 4 outputs and RS-485 half duplex
0 – 45 °C 32 – 113 °F)
Humidity 20 – 80% RH (non-condensing)
EN 61000-6-1, EN 61000-6-2, EN 55024, EN 55022 Class B, EN
61000-3-2, EN 61000-3-3, FCC Part 15 Subpart B Class B, AS/
NZS CISPR 22, ICES-003, VCCI Class B, ITE
EN 60950-1
270 g (0.6 lbs)
Installation Guide,
CD with installation and management tools, software and User’s
Manual, 1 Windows decoder user license
291 1U Video Server Rack
Expansion slots
3 slots for Axis blade video servers
Password protection, IP address filtering, HTTPS encryption,
IEEE 802.1X network access control
IPv4/v6, HTTP, HTTPS, QoS layer 3 DiffServ, FTP, SMTP, Bonjour,
UPnP, SNMPv1/v2c/v3(MIB-II), DNS, DynDNS, NTP, RTSP, RTP,
TCP, UDP, IGMP, RTCP, ICMP, DHCP, ARP, SOCKS
Supported
protocols
Powered from AXIS 291 1U Video Server Rack
Included
accessories
344.6 mm (13.6”)
311.2 mm (12.3”)
321 mm (12.6”)
182 mm (7.2”)
52.8 mm (2.1”)
344.6 mm (13.6”)
321 mm (12.6”)
AXIS 295
Video Surveillance Joystick
31 mm (1.2”)
Image settings
4x ETRAX 100LX, 4x ARTPEC-2, 4x 32 MB RAM, 4x 8 MB Flash
44.5 mm (1.8”)
Frame rate
MPEG-4
Frame rate
Motion JPEG
Video streaming
Connectors
31 mm (1.2”)
Video
compression
Resolutions
General
Processor and
memory
Power
44.5 mm (1.8”)
Video server
Models
For information on AXIS Camera Station and
video management software from
Axis’ Application Development Partners, see
www.axis.com/products/video/software/
©2009 Axis Communications AB. AXIS COMMUNICATIONS, AXIS, ETRAX, ARTPEC and VAPIX are registered trademarks or trademark applications of Axis AB
in various jurisdictions. All other company names and products are trademarks or registered trademarks of their respective companies. We reserve the right
to introduce modifications without notice.
32443/EN/R4/0902
www.axis.com
Download PDF