Aiwa | KSM-213CDM | Service manual | Aiwa KSM-213CDM Service manual

ZS-M35
SERVICE MANUAL
US Model
Canadian Model
Taiwan Model
Ver 1.2 2001.07
U.S. and foreign patents licensed from Dolby Laboratories
Licensing Corporation.
AUDIO POWER SPECIFICATIONS (US model)
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 4-ohm loads, both channels driven from
150 - 10,000 Hz; rated 4 W per channelminimum RMS power, with no more than 10%
total harmonic distortion in AC operation.
Model Name Using Similar Mechanism
CD
Section
MD
Section
CD Mechanism Type
PMC-20
KSM-213CDM
Optical Pick-up Name
KSS-213C
Model Name Using Similar Mechanism
PMC-MD55
MD Mechanism Type
MDM-5GA
Base Unit Name
MBU-5A
Optical Pick-up Name
KMS-260B
SPECIFICATIONS
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 785 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm) (CLV)
Number of programme positions
2
Frequency response
20 - 20,000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
MD player section
System
Minidisc digital audio system
Disc
MiniDisc
Laser diode properties
Material: GaAlAs
Wave length: 785 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance of
about 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
Recording/playback time
Stereo recording:
Maximum 80 minutes (with MDW-80)
Monaural recording:
Maximum 160 minutes (with MDW-80)
Revolutions
400 rpm to 900 rpm (CLV)
Error correction
Advanced Cross Interleave Reed Solomon Code
(ACIRC)
Sampling frequency
44.1 kHz
Radio section
Frequency range
FM: 87.5 - 108 MHz
AM: 530 - 1,710 kHz
Antennas
FM: Telescopic antenna
AM: AM loop antenna
– Continued on next page –
PERSONAL MINIDISC SYSTEM
9-927-183-33
Sony Corporation
2001G0400-1
© 2001.7
Personal Audio Company
Shinagawa Tec Service Manual Production Group
–1–
Coding
Adaptive TRansform Acoustic Coding (ATRAC)
Modulation system
EFM (Eight-to-Fourteen Modulation)
Number of programme positions
2 stereo programme positions
Frequency response
20 - 20,000 Hz +1/–2 dB
Signal-to-noise ratio
Over 80 dB (during playback)
Wow and flutter
Below measurable limit
General
Speaker
Full-range: 8 cm (3 in.) dia., 4 ohms, cone type (2)
Inputs
LINE IN (stereo minijack): Sensitivity 436 mV/
870 mV
Outputs
Headphones jack (stereo minijack) (1):
For 32 ohms impedance headphones
Power output (excluding US model)
5 W + 5 W (at 4 ohms, 10 % harmonic distortion
in AC operation)
Power requirements
For personal minidisc system:
120 V AC, 60 Hz
For back-up memory:
4.5 V DC, 3 size AA (R6) batteries
For remote control:
3 V DC, 2 size AA (R6) batteries
Power consumption
24 W
Dimensions (incl. projecting parts)
Approx. 498.5 × 173.5 × 227 mm (w/h/d)
(17 3/4 × 6 1/2 × 9 1/2 inches)
Mass
Approx. 5.2 kg (13 lb. 4 oz)
Supplied accessories
AC power cord (1)
Remote control (RMT-CM35A) (1)
AM loop antenna (1)
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage. Check
leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM
or battery-operated AC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a passive
VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
To Exposed Metal
Parts on Set
Design and specifications are subject to change
without notice.
0.15µF
1.5kΩ
AC
voltmeter
(0.75V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL
OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
–2–
TABLE OF CONTENTS
1. SERVICING NOTES
6. DIAGRAMS
1-1. Notes on Handling the Optical Pick-up Block or Base Unit .. 4
1-2. Notes on Laser Diode Emission Check ............................... 4
1-3. Notes on Chip Component Replacement ............................ 4
1-4. Flexible Circuit Board Repairing ........................................ 4
1-5. Chuck Plate Jig on Repairing .............................................. 4
1-6. Demonstration ..................................................................... 4
1-7. Checking the Laser Diode and Focus Search Operation ..... 4
1-8. Jig for Checking BD Board Waveform ............................... 5
1-9. Checks Prior to Parts Replacement and Adjustments ......... 6
1-10. Change of Pulley ................................................................. 6
6-1. IC Pin Function Descriptions ............................................ 33
6-2. Circuit Boards Location .................................................... 42
6-3. Block Diagram –Tuner Section– ....................................... 43
6-4. Block Diagram –MD Section– .......................................... 46
6-5. Block Diagram –CD Section– ........................................... 49
6-6. Block Diagram –Audio Section– ...................................... 51
6-7. Schematic Diagram –CD Section (1/2)– ........................... 53
6-8. Schematic Diagram –CD Section (2/2)– ........................... 55
6-9. Printed Wiring Boards –CD Section– ............................... 57
6-10. Printed Wiring Boards –Tuner Section– ........................... 59
6-11. Schematic Diagrams –Tuner Section– .............................. 61
6-12. Printed Wiring Boards –BD Section– ............................... 63
6-13. Schematic Diagram –BD Section (1/2)– ........................... 65
6-14. Schematic Diagrams –BD Section (2/2)– ......................... 67
6-15. Schematic Diagram –DG Section– ................................... 69
6-16. Schematic Diagram –DG Section– ................................... 71
6-17. Printed Wiring Board –DG Section– ................................. 73
6-18. Printed Wiring Board –Main Section– .............................. 75
6-19. Schematic Diagram –Main Section (1/3)– ........................ 77
6-20. Schematic Diagram –Main Section (2/3)– ........................ 79
6-21. Schematic Diagram –Main Section (3/3)– ........................ 81
6-22. Printed Wiring Boards –Panel Section– ............................ 83
6-23. Schematic Diagrams –Panel Section– ............................... 85
6-24. Printed Wiring Boards –Switch Section– .......................... 87
6-25. Schematic Diagrams –Switch Section– ............................ 89
6-26. Printed Wiring Boards –Power Supply Section– .............. 91
6-27. Schematic Diagrams –Power Supply Section– ................. 93
6-28. IC Block Diagrams ............................................................ 95
2. GENERAL
Playing a CD ....................................................................... 7
Recording a whole CD ........................................................ 7
Playing an MD ..................................................................... 8
Listening to the radio ........................................................... 8
3. DISASSEMBLY
3-1. Cabinet (Rear) Assy ............................................................ 9
3-2. Power Board ........................................................................ 9
3-3. Cabinet (Upper) Assy ........................................................ 10
3-4. MD Block Assy ................................................................. 10
3-5. Tuner Board ....................................................................... 11
3-6. Jack Board ......................................................................... 11
3-7. LED Board ........................................................................ 12
3-8. Key Board ......................................................................... 12
3-9. Top Board .......................................................................... 13
3-10. FL Board ........................................................................... 13
3-11. Main board ........................................................................ 14
3-12. CD Board .......................................................................... 14
3-13. CD Mechanism Block ....................................................... 15
3-14. DG Board .......................................................................... 15
3-15. Plate (Front), Shield .......................................................... 16
3-16. MD Mechanism Block-1 (MDM-5GA) ............................ 16
3-17. MD Mechanism Block-2 (Slider (Cam) Assy) ................. 17
3-18. MD Mechanism Block-3 (BD Board) ............................... 18
3-19. MD Mechanism Black-4 (SW Board) ............................... 18
7. EXPLODED VIEWS
7-1.
7-2.
7-3.
7-4.
7-5.
7-6.
7-7.
Cabinet (Rear) Section .................................................... 101
Cabinet (Front) Section ................................................... 102
Cabinet (Upper) Section .................................................. 103
MD Block Section ........................................................... 104
MD Mechanism Section (MDM-5GA) .......................... 105
MD Base unit Section (MBU-5A) ................................. 106
Optical Pick-up Section (KSM-213CDM) ...................... 107
8. ELECTRICAL PARTS LIST .................................... 108
4. TEST MODE
4-1. MD section ........................................................................ 19
5. ELECTRICAL ADJUSTMENTS
5-1. Tuner section ..................................................................... 22
5-2. MD section ........................................................................ 24
5-3. CD section ......................................................................... 31
–3–
SECTION 1
SERVICING NOTES
This Compact Disc player
is classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT label is located
on the bottom exterior.
1-5. CHUCK PLATE JIG ON REPAIRING
On repairing CD section, playing a disc without the CD lid, use
Chuck Plate Jig.
• Code number of Chuck Plate Jig: X-4918-255-1
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
1-1. NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
1-2. NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused
on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens.
1-3. NOTES ON CHIP COMPONENT REPLACEMENT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
1-6. DEMONSTRATION
This set enters the demonstration mode about 10 seconds after the
power cord is connected. The demonstration displays such as
“DEMONSTRATION MODE” and “CREATE YOUR ORIGINAL
MD” then appears.
When no operation is entered for one minute after the [POWER]
button is turned on, the demonstration mode is also entered.
To release the demonstration mode, set the timer in this set or press
and hold down the [NO/CANCEL] button for about 2 seconds.
1-7. CHECKING THE LASER DIODE AND FOCUS
SEARCH OPERATION
1. Turn on the POWER and open the CD cover.
2. As shown below, push S402 (CD DOOR) with a screwdriver or
other tool.
3. Press the CD button.
4. Check the objective lens to make sure that the laser diode is
emitting light. If not so, the auto power control circuit or optical
pickup would be damaged.
Verify that the objective lens moves vertically three times for
focus search.
1-4. FLEXIBLE CIRCUIT BOARD REPAIRING
• Keep the temperature of the soldering iron around 270 ˚C during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
S402
–4–
1-8. JIG FOR CHECKING BD BOARD WAVEFORM
The special jig (J-2501-149-A) is useful for checking the waveform of the BD board. The names of terminals and the checking items to
be performed are shown as follows.
GND : Ground
I+3V : For measuring IOP (Check the deterioration of the optical pick-up laser)
IOP : For measuring IOP (Check the deterioration of the optical pick-up laser)
TEO : TRK error signal (Traverse adjustment)
VC : Reference level for checking the signal
RF : RF signal (Check jitter)
Mechanism deck
CN110
6P connector
5P connector
RF
VC
TEO
IOP
I+3V
GND
RF
VC
1 RF
VC
TEO for MDM-3
IOP
5 I+3V
TEO
IOP
I+3V
GND
–5–
1 VC
RF
TEO for MDM-5
IOP
I+3V
6 GND
1-9. CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS (FOR MD SECTION)
Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent.
Details of the procedures are described in “5 Electrical Adjustments”.
Criteria for Determination
(Unsatisfactory if specified value is not satisfied)
Laser power check
(6-1 : See page 26)
Measure if unsatisfactory:
• 0.9 mW power
Specified value : 0.84 to 0.92 mW
• 7.0 mW power
Specified value : 6.8 to 7.2 mW
• Clean the optical pick-up
• Adjust again
• Replace the optical pick-up
lop (at 7mW)
• Labeled on the optical pickup
Iop value ± 10mA
• Replace the optical pick-up
Focus bias check
(6-2 : See page 26)
• Error rate check
Specified value : For points a, b, and c
C1 error : About 200
ADER : Below 2
• Replace the optical pick-up
C PLAY check
(6-3 : See page 26)
• Error rate check
Specified value:
a. When using test disc (MDW-74/AU-1)
C1 error : Below 80
ADER : Below 2
b. When using check disc (TDYS-1)
C1 error : Below 50
• Replace the optical pick-up
Self-recording/playback
check
(6-4 : See page 26)
• CPLAY error rate check
Specified value:
C1 error : Below 80
ADER : Below 2
If always unsatisfactory:
• Replace the overwrite head
• Check for disconnection of the circuits around the
overwrite head
If occasionally unsatisfactory:
• Check if the overwrite head is distorted
• Check the mechanism around the sled
Note:
The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for
adjustments.
When performing adjustments, use the specified values for adjustments.
1-10. CHANGE OF PULLEY
pulley
M102, 103
2.5 mm
Install the pulley to the motor.
–6–
SECTION 2
GENERAL
This section is extracted
from instruction manual.
Basic Operations
Playing a CD
Use these buttons for additional operations
3
.,>
1, 2
CD u CD x
VOLUME –, +
POWER
Tip
Next time you want to
listen to a CD, just press
CD u. The player
turns on automatically
and starts playing the
CD.
For hookup instructions, see pages 57 - 59.
1
Press Z PUSH OPEN/CLOSE
down to open the CD
compartment and place the CD
on the CD compartment.
With the label side up
2
Press
adjust the volume
VOLUME +, –
(VOL +, – on the remote)
stop playback
CD x
pause playback
CD u (CD X on the
remote)
Press the button again to
resume play after pause.
go to the next track
>
go back to the previous track
.
remove the CD
Z PUSH OPEN/CLOSE
turn on/off the player
POWER
Close the lid of the CD
compartment.
3
Press CD u (CD N on the
remote).
The player turns on (direct
power-on) and the player plays
all the tracks once.
4
To
Basic Operations
Z PUSH
OPEN/CLOSE
Display
Track
number
Playing
time
Basic Operations
Basic Operations
5
Recording a whole CD
(Synchronized recording)
4
5
3
1
4
2
To record at high speed, press
HIGH SPEED.
To record at normal speed, skip this step.
5
Press SYNCHRO REC CD N
MD.
The player starts recording
automatically.
If the MD has any previous
recording, recording will be
made from the last recorded
position.
For hookup instructions, see pages 57 - 59.
1
Insert a recordable MD (direct
power-on).
With the label
side up
After “TOC Reading” is
displayed, the disc name
will be displayed if it is
labeled.
2
Press Z PUSH OPEN/CLOSE
and place the CD on the CD
compartment.
Press Z PUSH OPEN/CLOSE
again to close the CD
compartment.
With the label side up
3
6
Use these buttons for additional operations
After you
stop recording, do not
disconnect the AC
power cord or move
the player while “TOC
EDIT” is flashing in the
display. If you do so,
recording may not be
done properly.
• When you record a
whole CD, you cannot
pause recording.
POWER
Tips
• Adjusting the volume or
the audio emphasis
(page 49) will not affect
the recording level.
Keep the volume at a
moderate level so as to
prevent the sound from
skipping.
• To record over the
previous recording, see
page 33.
• Once the clock is set, the
recording date and time
are stamped
automatically (page 50).
• You can label an MD or a
track during recording
(page 44).
Insert in the direction of
the arrow
Press CD x.
Basic Operations
Remaining
recording
time of MD
Notes
•
Display
Track number
of MD
CD x
MD x
YES
ENTER
NO
CANCEL
To
Press
stop recording
MD x or CD x
turn on/off the player
POWER
If “CD>MD OK?” alternates with time display
There is not enough space on the MD to record the whole
CD.
If it is all right to record as much as possible and cancel
recording of some tracks, press YES•ENTER. To stop
recording, press NO•CANCEL.
If any other messages are displayed, see page 72.
Basic Operations
–7–
Basic Operations
The indicator lights up.
7
Playing an MD
Use these buttons for additional operations
., >
2
1
MD u
MD x
POWER
Basic Operations
VOLUME –, +
Z
Tip
Next time you want to
listen to a MD, just press
MD u. The player
turns on automatically
and starts playing the
MD.
For hookup instructions, see pages 57 - 59.
1
Insert the MD (direct power-on).
Display
After “TOC Reading” is
displayed, the disc name
will be displayed if it is
labeled.
With the label
side up
Insert in the direction of
the arrow
2
Press MD u (MD N on the
remote).
To
Press
adjust the volume
VOLUME +, –
(VOL +, – on the remote)
stop playback
MD x
pause playback
MD u (MD X on the
remote)
Press the button again to
resume play after pause.
go to the next track
>
go back to the previous track
.
remove the MD
Z
turn on/off the player
POWER
Track name is displayed
if it is labeled.
The player plays all the tracks
once.
m
Track number
8
Playing time
Basic Operations
Basic Operations
9
Listening to the radio
Use these buttons for additional operations
2
POWER
1
MONO/ST
REPEAT
Tips
• If the FM broadcast is
noisy, press MONO/
ST•REPEAT (MODE on
the remote) until
“Mono” appears in the
display and radio will
play in monaural.
• Next time you want to
listen to the radio, just
press RADIO BAND.
The player turns on
automatically and starts
playing the previous
station.
For hookup instructions, see pages 57- 59.
1
Press RADIO BAND until the
band you want appears in the
display (direct power-on).
Display
“FM” or “AM” appears
2
Hold down TUNE + or TUNE –
until the frequency digits begin to
change in the display.
Press
adjust the volume
VOLUME +, –
(VOL +, – on the remote)
turn on/off the radio
POWER
To improve broadcast reception
FM:
Reorient the antenna for FM.
Indicates an FM stereo
broadcast
The player automatically scans
the radio frequencies and stops
when it finds a clear station.
AM:
If you can’t tune in a station,
press TUNE + or TUNE –
repeatedly to change the
frequency step by step.
10
To
Basic Operations
VOLUME –, +
Keep the AM loop antenna as far as possible from the
player and reorient it.
Basic Operations
Basic Operations
–8–
11
SECTION 3
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
Set
Cabinet (Rear)
Assy
Cabinet (Upper) Assy
FL Board
Power Board
Top Board
Main
Board
CD Mechanism
Block
CD
Board
MD Block Assy
Tuner Board
Jack Board
DG Board
LED Board
Key Board
Plate (Front), Shield
MD Mechanism
Block - 1
(MDM-5GA)
MD Mechanism
Block - 2
(Slider (Cam) Assy)
MD Mechanism
Block - 3
(BD Board)
MD Mechanism
Block - 4
(SW board)
Note : Follow the disassembly procedure in the numerical order given.
3-1. CABINET (REAR) ASSY
7 CN401
6 CN402
1 BVTP 3x12
handle
2 BVTP 3x14
8 cabinet (rear) assy
3 BVTP 3x14
5 BVTP 3x14
4 BVTP 3x12
3-2. POWER BOARD
1 BVTP 3x12
cabinet (rear) assy
chassis, transformer
3 BVTP 4x12
5
4 BVTP 3x12
6 POWER board
2 CN903
–9–
3-3. CABINET (UPPER) ASSY
qacabinet (upper) assy
2 CN705
3 CN404
4 connector
9 CN406
q; CN409
1 BVTP 3x10
8 CN407
7 CN303
6 CN408
5 CN301
3-4. MD BLOCK ASSY
3 MD block assy
2 BVTP 3x14
1 CN2
– 10 –
3-5. TUNER BOARD
1 BVTP 3x10
chassis (TU)
4 BVTP 3x10
2 BVTP 3x10
5 TUNER board
3 BVTP 3x10
3-6. JACK BOARD
1 BVTP 2.6x8
3 JACK board
– 11 –
2 CN306
3-7. LED BOARD
1 BVTP 2.6x8
2 BVTP 2.6x8
3 LED board
3-8. KEY BOARD
1 BVTP 2.6x8
2 BVTP 2.6x8
3 KEY board
– 12 –
3-9. TOP BOARD
2
1 BVTP 2.6x8
5 TOP board
4 button (top)
3 BVTP 2.6x8
3-10. FL BOARD
1 CN405
3 FL board
2 BVTP 3x10
– 13 –
3-11. MAIN BOARD
5 BVTP 3x10
1 CN410
4 BVTP 3x10
6 BVTP 3x10
8 MAIN board
7 CN403
2 CN707
3 CN704
CD board
3-12. CD BOARD
1 CN801
2 BVTP 3x10
3 BVTP 3x10
4 CN701
5 CD board
– 14 –
3-13. CD MECHANISM BLOCK
1 PWH 2.6x10
2 PWH 2.6x10
3
4 CD mechanism block
3-14. DG BOARD
1 P 2.6x5
2 plate (lower) , shield
5 CN605
6 CN603
4 P 2.6x5
7
3 P 2.6x5
q; DG board
8 CN602
9 CN601
claws
– 15 –
3-15. PLATE (FRONT), SHIELD
3 plate (front), shield
2 P 2.6x5
1 P 2.6x5
3-16. MD MECHANISM BLOCK-1 (MDM-5GA)
3 claws
5 plate (upper), shield
4 claws
6 BVTTWH M3
7 BVTTWH M3
9 MD mechanism block
(MDM-5GA)
8 harnes
1 P 2.6x5
2 P 2.6x5
– 16 –
3-17. MD MECHANISM BLOCK-2 (SLIDER (CAM) ASSY)
6 slider (cam) assy
3 bracket (guide L)
1 BV 2.6 (1T3B)
2 spring, leaf
4 BV 2.6 (1T3B)
5 bracket (guide R)
horizontal
When assembling, set the press
fitting shaft of the cam gear
horizontal to the lever (head).
press
fitting
shaft
lever (head)
cam gear
A
When assembling, insert the
shaft of the lever (O/C)
with A part fit in the slot.
– 17 –
3-18. MD MECHANISM BLOCK-3 (BD BOARD)
2 MD base unit
BD board (side A)
5 CN104
6 CN101
1 BV 2.6 (1T3B)
3 Removal the solders
7 BD board
4 M 1.7
3-19. MD MECHANISM BLOCK-4 (SW BOARD)
2 gear (B)
1 PTPWH M 2.6x6
3 PWH 1.7x4
4 motor assy, loading
6 SW board
5 BTP 2.6x6
– 18 –
SECTION 4
TEST MODE
Refer to “5. ELECTRICAL ADJUSTMENT” for the test mode of CD section.
4-1. MD SECTION
1. PRECAUTIONS FOR USE OF TEST MODE
• As loading related operations will be performed regardless of the test mode operations being performed, be sure to check that the disc is
stopped before setting and removing it.
Even if the Z (MD) button is pressed while the disc is rotating during continuous playback, continuous recording, etc., the disc will not
stop rotating.
Therefore, it will be ejected while rotating.
Be sure to press the Z (MD) button after pressing the [REC/REC MODE] button and the rotation of disc is stopped.
1-1. Recording laser emission mode and operating buttons
• Continuous recording mode (CREC MODE)
• Laser power check mode (LDPWR CHECK)
• Laser power adjustment mode (LDPWR ADJUST)
• When pressing the [REC] button.
2. SETTING THE TEST MODE
1. Set to standby state.
2. Press the buttons [SOUND] and [EDIT] and . (TUNE –) at the same time and then release them soon (within 100m sec). The TEST
MODE is entered.
3. RELEASING THE TEST MODE
Hold down the [POWER] button and remove the power cord to reset the set.
4. BASIC OPERATIONS OF THE TEST MODE
All operations are performed with the following buttons: u (MD), x (MD), [RADIO/BAND], and [REC/REC MODE].
The functions of these buttons are as follows.
Function name
u (MD)
Function
Proceeds the parameter/mode change.
x (MD)
Returns to the parameter/mode change.
RADIO/BAND
Goes ahead. Determines the setting/selection.
REC/REC MODE
Suspends.
5. SELECTING THE TEST MODE
There are 9 types of test modes as shown below. The groups can be switched by press the u (MD) or x (MD) button. After selecting the
group to be used, press the [RADIO/BAND] button. After setting a certain group, press the u (MD) or x (MD) button between these modes.
Display
Contents
TEMP ADJUST
Temperature compensation offset adjustment
LDPWR ADJUST
Laser power adjustment
LDPWR CHECK
Laser power check
EFBAL ADJUST
EF balance adjustment
FBIAS ADJUST
Focus bias adjustment
FBIAS CHECK
Focus bias check
CPLAY MODE
Continuous playback mode
CREC MODE
Continuous recording mode
EEP MODE
Non-volatile memory control
• For details of each adjustment mode, refer to “5. Electrical Adjustments”.
• If a different mode has been selected by mistake, press the [REC/REC MODE] button to release that mode.
• EEP MODE is not used for servicing and therefore are not described in detail. If these modes are set accidentally, press the [REC/REC MODE]
button to release the mode immediately. Be especially careful this mode will overwrite the non-volatile memory and reset it, and as a
result, the unit will not operate normally.
– 19 –
5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
(1) Set the disc in the unit. (Whichever recordable discs or discs for playback only are available)
(2) Press the u (MD) or x (MD) button to display “CPLAY MODE”.
(3) Press the [RADIO/BAND] button to change the display to “CPLAY MID”.
(4) When access completes, the display changes to “C1 =
AD = ”.
Note: The numbers “ ” displayed show you error rates and ADER.
2. Changing the parts to be played back
(1) Press the [RADIO/BAND] button during continuous playback to change the display as below.
“CPLAY MID” t “CPLAY OUT” t “CPLAY IN”
When pressed another time, the parts to be played back can be moved.
When access completes, the display changes to “C1 =
AD = ”.
Note: The numbers “ ” displayed show you error rates and ADER.
3. Ending the continuous playback mode
(1) Press the [REC/REC MODE] button. The display will change to “CPLAY MODE”.
(2) Press the Z (MD) button and take out the disc.
Note: The playback start addresses for IN, MID, and OUT are as follows.
IN : 40h cluster
MID : 300h cluster
OUT : 700h cluster
(2)
5-2. Operating the Continuous Recording Mode (Use only when performing self-recording/palyback check)
1. Entering the continuous recording mode
(1) Set a recordable disc in the unit.
(2) Press the u (MD) or x (MD) button to display “CREC MODE”.
(3) Press the [RADIO/BAND] button to change the display to “CREC MID”.
(4) When access completes, the display changes to “CREC (
)” and “[REC]” lights up.
Note: The numbers “ ” displayed shows you the recording position addresses.
2. Changing the parts to be recorded
(1) When the [RADIO/BAND] button is pressed during continuous recording, the display changes as below.
“CREC MID” t “CREC OUT” t “CREC IN”
When pressed another time, the parts to be recorded can be changed. “[REC]” goes off.
When access completes, the display changes to “CREC (
)” and “[REC]” lights up.
Note: The numbers “ ” displayed shows you the recording position addresses.
3. Ending the continuous recording mode
(1) Press the [REC/REC MODE] button. The display changes to “CREC MODE” and “[REC]” goes off.
(2) Press the Z (MD) button and take out the disc.
Note 1: The recording start addresses for IN, MID, and OUT are as follows.
IN : 40h cluster
MID : 300h cluster
OUT : 700h cluster
Note 2: The [REC/REC MODE] button can be used to stop recording anytime.
Note 3: Do not perform continuous recording for long periods of time above 5 minutes.
Note 4: During continuous recording, be careful not to apply vibration.
(2)
5-3. Non-Volatile Memory Mode (EEP MODE)
This mode reads and writes the contents of the non-volatile memory.
It is not used in servicing. If the unit entered this mode accidentally, press the [REC/REC MODE] button immediately to release it.
– 20 –
6. FUNCTIONS OF OTHER BUTTONS
Function
Contents
u (MD) and EDIT
Sets continuous playback when pressed in the STOP state. When pressed during continuous playback,
the tracking servo turns ON/OFF.
x (MD) and EDIT
Stops continuous playback and continuous recording.
>
The sled moves to the outer circumference only when this is pressed.
.
The sled moves to the inner circumference only when this is pressed.
REC/REC MODE and EDIT
When pressed during continuous playback, REC ON/OFF.
x (CD) and EDIT
Switches between the pit and groove modes when pressed.
RADIO/BAND and EDIT
When pressed during continuous playback, switches the spindle servo mode (CLV-S y CLV-A).
LINE/LINE LEVEL
Switches the displayed contents each time the button is pressed
Z (MD)
Ejects the disc
POWER
Releases the test mode
7. TEST MODE DISPLAYS
Each time the [LINE/LINE LEVEL] button is pressed, the display changes in the following order.
1. Mode display
Displays “TEMP ADJUST”, “CPLAYMODE”, etc.
Mode display
2. Error rate display
Displays the error rate in the following way.
C1 = ssss AD = ss
C1 = Indicates the C1 error.
AD = Indicates ADER.
Error rate display
Address display
3. Address display
The address is displayed as follows. (MO: recordable disc, CD: playback only disc)
Press the x (CD) and [EDIT] buttons at the same time to switches between the groove display
and pit display.
h = ssss s = ssss (MO pit and CD)
h = ssss a = ssss (MO groove)
h = Indicates the header address.
s = Indicates the SUBQ address.
a = Indicates the ADIP address.
Note: “–” is displayed when servo is not imposed.
4. Auto gain display (Not used in servicing)
The auto gain is displayed as follows.
AG F = ss T = ss
5. IVR display (Not used in servicing)
The IVR is displayed as follows.
[ss][ss][ss]
MEANINGS OF OTHER DISPLAYS
Contents
Display
When Lit
When Off
SHUF
During continuous playback (CLV: ON)
STOP (CLV: OFF)
PGM
Tracking servo OFF
Tracking servo ON
[REC]
Recording mode ON
Recording mode OFF
TOC EDIT
ABCD adjustment completed
TRACK
Pit
Groove
TIMER
CLV-S
CLV-A
– 21 –
Auto gain display
(Not used in servicing)
IVR display
(Not used in servicing)
SECTION 5
ELECTRICAL ADJUSTMENTS
5-1. TUNER SECTION
0 dB = 1 µV
FM FREQUENCY COVERAGE
ADJUSTMENT
• FM Section
Setting:
BAND button: FM
FM RF signal
generator
Frequency Display
87.5 MHz
108 MHz
Reading on Digital voltmeter
+ 0.4 V
1.3 – 0.2 V
+ 0.3 V
3.0 – 0.5 V
<confirmation>
L2
Adjustment Part
FM antenna
(JW1,2)
0.01 µF
FM TRACKING ADJUSTMENT
set
Adjust for a maximum reading on level meter.
75 kHz frequency
deviation by 1 kHz signal
output level : as low as possible
• AM Section
Setting:
BAND button: AM
L1
CT1
87.5 MHz
108 MHz
AM FREQUENCY COVERAGE
ADJUSTMENT
Frequency Display
AM RF signal
generator
530 kHz
1,710 kHz
0.8 ± 0.2 V
5.5 ± 0.3 V
<confirmation>
L4
Reading on Digital voltmeter
Put the lead-wire
antenna close to
the supplied
AM loop antenna.
Adjustment Part
AM TRACKING ADJUSTMENT
30% amplitude
modulation by 400 Hz signal
output level : as low as possible
Adjust for a maximum reading on level meter.
L3
CT2
620 kHz
1,400 kHz
• Connecting Level Meter (FM and AM)
AM IF ADJUSTMENT
level meter
(range: 0.5-5 V ac)
Adjust for a maximum reading on level meter.
T1
32 Ω
450 kHz
set
Adjustment Location: TUNER board (See page 23.)
i jack (J301)
• Connecting Digital Voltmeter (FM and AM)
digital
voltmeter
tuner board
TP (VT)
• Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.
– 22 –
Adjustment Location:
(COMPONENT SIDE)
JW1
JW2
T1
AM IF
ADJUSTMENT
L2
FM FREQUENCY
COVERAGE
ADJUSTMENT
L1
CT1
FM
TRACKING
ADJUSTMENT
L4
AM FREQUENCY
COVERAGE
ADJUSTMENT
L3
CT2
TP(VT)
– 23 –
AM
TRACKING
ADJUSTMENT
5-2. MD SECTION
1. PARTS REPLACEMENT AND ADJUSTMENT
• Check and adjust the mechanism deck as follows.
The procedure changes according to the part replaced.
• Abbreviation
OP
: Optical pick-up
OWH : Overwrite head
• Laser power check
• Focus bias check
• C PLAY check
• Self-recording/playback check
OK
NG
Check the sled and spindle
mechanisms.
Other causes can be suspected.
Parts Replacement and Repair
YES
Has the OWH been replaced?
NO
NO
Has OP, IC171, IC101, or
IC121 been replaced?
YES
Initial setting of the adjustment value
Has OP or IC171 been replaced?
NO
YES
IOP information recording
(IOP value labeled on OP)
Has IC171 or D101
been replaced?
NO
YES
Temperature compensation offset adjustment
• Laser power adjustment
• Traverse adjustment
• Focus bias adjustment
• Error rate adjustment
• Focus bias check
• Auto gain adjustment
– 24 –
2. PRECAUTIONS FOR CHECKING LASER DIODE
EMISSION
To check the emission of the laser diode during adjustments, never
view directly from the top as this may lose your eye-sight.
3. PRECAUTIONS FOR USE OF OPTICAL PICK-UP
(KMS-260B)
As the laser diode in the optical pick-up is easily damaged by static
electricity, solder the laser tap of the flexible board when using it.
Before disconnecting the connector, desolder first. Before connecting the connector, be careful not to remove the solder. Also take
adequate measures to prevent damage by static electricity. Handle
the flexible board with care as it breaks easily.
pick-up
flexible board
Laser Power Meter
When performing laser power checks and adjustment (electrical
adjustment), use of the new MD laser power meter 8010S (Part No.
J-2501-145-A) instead of the conventional laser power meter is convenient.
It sharply reduces the time and trouble to set the laser power meter
sensor onto the objective lens of optical pick-up.
laser tap
Optical pick-up flexible board
5. CREATING CONTINUOUSLY-RECORDED DISC
4. PRECAUTIONS FOR ADJUSTMENTS
1. When replacing the following parts, perform the adjustments
and checks with in the order shown in the following table.
Optical
Pick-up IC171
BD Board
D101
4. Use the following tools and measuring device.
• Check Disc (MD) TDYS-1
(Part No. 4-963-646-01)
• Test Disc (MDW-74/AU-1) (Part No. 8-892-341-41)
• Laser power meter LPM-8001 (Part No. J-2501-046-A)
or MD Laser power meter 8010S (Part No. J-2501-145-A)
• Oscilloscope (Measure after performing CAL of prove)
• Digital voltmeter
• Thermometer
• Jig for checking BD board waveform
(Part No. : J-2501-149-A)
5. When observing several signals on the oscilloscope, etc., make
sure that VC and ground do not connect inside the oscilloscope.
(VC and ground will become short-circuited)
6. Using the above jig enables the waveform to be checked without the need to solder.
(Refer to Servicing Notes on page 5)
7. As the disc used will affect the adjustment results, make sure
that not dusts nor fingerprints are attached to it.
IC101, IC121 IC192
1. Temperature
compensation
offset adjustment
2. Laser power
adjustment
* This disc is used in focus bias adjustment and error rate check.
The following describes how to create a continuous recording
disc.
1. Insert a disc (blank disc) commercially available.
2. Press the u (MD) or x (MD) button to display “CREC
MODE”.
3. Press the [RADIO/BAND] button again to display “CREC MID”.
Display “CREC (0300)” and start to recording.
4. Complete recording within 5 minutes.
5. Press the [REC/REC MODE] button and stop recording.
6. Press the Z (MD) button and remove the disc.
The above has been how to create a continuous recorded data for
the focus bias adjustment/check and MO error rate check.
3. EF balance
adjustment
Note:
• Be careful not to apply vibration during continuous recording.
4. Focus bias
adjustment
5. Error rate check
2. Set the test mode when performing adjustments.
After completing the adjustments, release the test mode.
Perform the adjustments and checks in “group S” of the test
mode.
3. Perform the adjustments to be needed in the order shown.
– 25 –
6. CHECK PRIOR TO REPAIRS
These checks are performed before replacing parts according to
“approximate specifications” to determine the faulty locations. For
details, refer to “Checks Prior to Parts Replacement and Adjustments” (See page 6).
6-1. Laser Power Check
Connection:
laser
power meter
Optical pick-up
objective lens
digital voltmeter
BD board
CN110 pin 5 (I +3V)
CN110 pin 4 (IOP)
+
–
Checking Procedure:
1. Set the laser power meter on the objective lens of the optical
pick-up. (When it cannot be set properly, press the . button or > button to move the optical pick-up)
Connect the digital voltmeter to CN110 pin 5 (I+3 V) and
CN110 pin 4 (IOP) on the BD board.
2. Press the u (MD) or x (MD) button to display “LDPWR
CHECK”.
3. Press the [RADIO/BAND] button once to display “LD 0.9 mW $
”. Check that the reading of the laser power meter become
0.84 to 0.92 mW.
4. Press the [RADIO/BAND] button once more to display “LD 7.0
mW $ ”. Check that the reading the laser power meter and
digital voltmeter satisfy the specified value.
Specified Value:
Laser power meter reading : 7.0 ± 0.2 mW
Digital voltmeter reading : Value on the optical pick-up label
± 10 %
(Optical pick-up label)
KMS260B
27X40
B0825
6-2. Focus Bias Check
Change the focus bias and check the focus tolerance amount.
Checking Procedure:
1. Load the test disc (MDW-74/AU-1).
2. Press the u (MD) or x (MD) button to display “CPLAY
MODE”.
3. Press the [RADIO/BAND] button twice to display “CPLAY MID”.
AD = ”
4. Press the [REC/REC MODE] button when “C1 =
is displayed.
5. Turn the JOG dial to display “FBIAS CHECK”.
6. Press the [RADIO/BAND] button to display “
/ c = ”.
The first four digits indicate the C1 error rate, the two digits
after [/] indicate ADER, and the 2 digits after [c =] indicate the
focus bias value.
Check that the C1 error is below 50 and ADER is below 2.
7. Press the [RADIO/BAND] button to display “
/ b = ”.
Check that the C1 error is about 200 and ADER is below 2.
/ a = ”.
8. Press the [RADIO/BAND] button to display “
Check that the C1 error is about 200 and ADER is below 2.
9. Press the [REC/REC MODE] button, then press the Z (MD)
button and take out the test disc.
6-3. C PLAY Check
MO Error Rate Check
Checking Procedure:
1. Load the test disc (MDW-74/AU-1).
2. Press the u (MD) or x (MD) button to display “CPLAY
MODE”.
3. Press the [RADIO/BAND] button to display “CPLAY MID”.
4. The display changes to “C1 =
AD = ”.
5. If the C1 error rate is below 80, check that ADER is below 2.
6. Press the [REC/REC MODE] button to stop playback, then press
the Z (MD) button and take out the test disc.
CD Error Rate Check
Checking Procedure:
1. Load the check disc (MD) TDYS-1.
2. Press the u (MD) or x (MD) button to display “CPLAY
MODE”.
3. Press the [RADIO/BAND] button twice to display “CPLAY MID”.
4. The display changes to “C1 =
AD = ”.
5. Check that the C1 error rate is below 50.
6. Press the [REC/REC MODE] button to stop playback, then press
the Z (MD) button and take out the check disc.
6-4. Self-Recording/playback Check
Prepare a continuous recording disc using the unit to be repaired
and check the error rate.
lOP=82.5 mA in this case
lOP (mA) = Digital voltmeter reading (mV)/1 (Ω)
5. Press the [REC/REC MODE] button to display “LDPWR CHECK”
and stop the laser emission.
(The [REC/REC MODE] button is effective at all times to stop
the laser emission)
Note 1: After step 4, each time the [RADIO/BAND] button is pressed, the
display will be switched “LD 0.7 mW $ ”, “LD 6.2 mW $ ”,
and “LD WP
$ ”. Nothing needs to be performed here.
(
= correction)
Checking Procedure:
1. Load a recordable disc (blank disc).
2. Press the u (MD) or x (MD) button to display “CREC
MODE”.
3. Press the [RADIO/BAND] button to display “CREC MID”.
4. When recording starts, lights up “[REC]” and display “CREC
@@@@” (@@@@ is the address).
5. About 1 minute later, press the [REC/REC MODE] button to stop
continuous recording.
6. Turn the JOG dial to display “CPLAY MODE”.
7. Press the [RADIO/BAND] button to display “CPLAY MID”.
8. “C1 =
AD = ” will be displayed.
9. Check that the C1 error becomes below 80 and the ADER below 2.
10. Press the [REC/REC MODE] button to stop play back, then press
the Z (MD) button and take out the disc.
Note: After the TEST MODE is entered, insert the disc.
– 26 –
7. TEMPERATURE COMPENSATION OFFSET
ADJUSTMENT
Save the temperature data at that time in the non-volatile memory
as 25 °C reference data.
Note:
1. Usually, do not perform this adjustment.
2. Perform this adjustment in an ambient temperature of 22 °C to 28 °C.
Perform it immediately after the power is turned on when the internal
temperature of the unit is the same as the ambient temperature of 22 °C
to 28 °C.
3. When D101 has been replaced, perform this adjustment after the temperature of this part has become the ambient temperature.
Adjusting Procedure:
1. Press the u (MD) or x (MD) button to display “TEMP
ADJUST”.
2. Press the [RADIO/BAND] button to select the “TEMP ADJUST”
mode.
3. “TEMP = ” and the current temperature data will be displayed.
4. To save the data, press the [RADIO/BAND] button.
When not saving the data, press the [REC/REC MODE] button.
5. When the [RADIO/BAND] button is pressed, “TEMP = SAVE”
will be displayed and turned back to “TEMP ADJUST” display
then. When the [REC/REC MODE] button is pressed, “TEMP
ADJUST” will be displayed immediately.
Specified Value:
The “TEMP = ” should be within “E0 - EF”, “F0 - FF”, “00 0F”, “10 - 1F” and “20 - 2F”.
Specified Value:
Laser power meter reading : 7.0 ± 0.2 mW
Digital voltmeter reading : Value on the optical pick-up label
± 10%
(Optical pick-up label)
KMS260B
27X40
B0825
lOP=82.5 mA in this case
lOP (mA) = Digital voltmeter reading (mV)/1 (Ω)
10. Press the [REC/REC MODE] button to display “LDPWR CHECK”
and stop the laser emission.
(The [REC/REC MODE] button is effective at all times to stop
the laser emission)
Note 1: After step 9, each time the [RADIO/BAND] button is pressed, the
display will be switched “LD 0.7 mW $ ”, “LD 6.2 mW $ ”,
and “LD WP
$ ”. Nothing needs to be performed here.
(
= correction)
8. LASER POWER ADJUSTMENT
Connection:
7. Then, press the u (MD) or x (MD) to display “LDPWR
CHECK”.
8. Press the [RADIO/BAND] button once to display “LD 0.9mW $
”. Check that the reading of the laser power meter become
0.85 to 0.91 mW.
9. Press the [RADIO/BAND] button once more to display “LD 7.0
mW $ ”. Check that the reading the laser power meter and
digital voltmeter satisfy the specified value.
Note down the digital voltmeter reading value.
laser
power meter
Optical pick-up
objective lens
digital voltmeter
BD board
CN110 pin 5 (I +3V)
CN110 pin 4 (IOP)
+
–
Adjusting Procedure:
1. Set the laser power meter on the objective lens of the optical
pick-up. (When it cannot be set properly, press the . button or > button to move the optical pick-up)
Connect the digital voltmeter to CN110 pin 5 (I+3 V) and
CN110 pin 4 (IOP) on the BD board.
2. Press the u (MD) or x (MD) button to display “LDPWR
ADJUST”.
(Laser power: For adjustment)
3. Press the [RADIO/BAND] button once to display “LD 0.9 mW $
”.
4. Press the u (MD) or x (MD) button so that the reading of
the laser power meter becomes 0.85 to 0.91 mW. Press the
[RADIO/BAND] button after setting the range knob of the laser
power meter, and save the adjustment results. (“LD SAVE $
” will be displayed for a moment)
5. Then “LD 7.0 mW $ ” will be displayed.
6. Press the u (MD) or x (MD) button and adjust so that the
reading on the laser power meter is 6.9 to 7.1 mV. Press the
[RADIO/BAND] button to save the setting.
Note: Do not perform the emission with 7.0 mW more than 15 seconds
continuously.
– 27 –
9. EF BALANCE ADJUSTMENT
8. Press the u (MD) or x (MD) button so that the waveform
of the oscilloscope becomes the specified value.
(When the JOG dial is turned, the of “EFB- ” changes and
the waveform changes) In this adjustment, waveform varies at
intervals of approx. 2%. Adjust the waveform so that the specified value is satisfied as much as possible.
(Write power traverse adjustment)
Note 1: Data will be erased during MO reading if a recorded disc is
used in this adjustment.
Note 2: If the traverse waveform is not clear, connect the oscilloscope
as shown in the following figure so that it can be seen more
clearly.
oscilloscope
(DC range)
BD board
Traverse Waveform
330 k Ω
CN110 pin 3 (TEO)
+
–
CN110 pin 1 (VC)
A
VC
10 pF
B
Connection:
Specification A = B
oscilloscope
(DC range)
BD board
CN110 pin 3 (TEO)
CN110 pin 1 (VC)
+
–
V: 0.1 V/div
H: 10 ms/div
Adjusting Procedure:
1. Connect an oscilloscope to CN110 pin 3 (TEO) and CN110
pin 1 (VC) on the BD board.
2. Load a disc (any available on the market). (Refer to Note 1)
3. Press the > button to move the optical pick-up outside the
pit.
4. Press the u (MD) or x (MD) button to display “EFBAL
ADJUST”.
MO-R”.
5. Press the [RADIO/BAND] button to display “EFB =
(Laser power READ power/Focus servo ON/tracking servo OFF/
spindle (S) servo ON)
6. Press the u (MD) or x (MD) button so that the waveform
of the oscilloscope becomes the specified value.
(When the u (MD) or x (MD) button is pressed, the of
“EFB = ” changes and the waveform changes ) In this adjustment, waveform varies at intervals of approx. 2 %. Adjust the
waveform so that the specified value is satisfied as much as
possible.
(Read power traverse adjustment)
Traverse Waveform
A
VC
B
Specification A = B
7. Press the [RADIO/BAND] button and save the result of adjustment to the non-volatile memory. (“EFB =
SAVE” will be
displayed for a moment. Then “EFB = MO-W” will be displayed)
9. Press the [RADIO/BAND] button, and save the adjustment results in the non-volatile memory. (“EFB =
SAVE” will be
displayed for a moment)
10. “EFB = MO-P” will be displayed.
The optical pick-up moves to the pit area automatically and
servo is imposed.
11. Press the u (MD) or x (MD) button until the waveform of
the oscilloscope moves closer to the specified value.
In this adjustment, waveform varies at intervals of approx. 2%.
Adjust the waveform so that the specified value is satisfied as
much as possible.
Traverse Waveform
A
VC
B
Specification A = B
12. Press the [RADIO/BAND] button, and save the adjustment reSABE” will be
sults in the non-volatile memory. (“EFB =
displayed for a moment)
Next “EFBAL ADJUST” is displayed. The disc stops rotating
automatically.
13. Press the Z (MD) button and take out the disc.
14. Load the check disc (MD) TDYS-1.
15. Press the [RADIO/BAND] button to display “EFB = CD”. Servo
is imposed automatically.
16. Turn the JOG dial so that the waveform of the oscilloscope
moves closer to the specified value.
In this adjustment, waveform varies at intervals of approx. 2%.
Adjust the waveform so that the specified value is satisfied as
much as possible.
Traverse Waveform
A
VC
B
Specification A = B
– 28 –
17. Press the [RADIO/BAND] button, display “EFB = SAVE” for
a moment and save the adjustment results in the non-volatile
memory.
Next “EFBAL ADJUST” will be displayed.
18. Press the Z (MD) button and take out the disc.
10. FOCUS BIAS ADJUSTMENT
Adjusting Procedure:
1. Load the continuously-recorded disc. (Refer to “5. CREATING
CONTINUOUSLY-RECORDED DISC”)
2. Press the u (MD) or x (MD) button to display “CPLAY
MODE”.
3. Press the [RADIO/BAND] button to display “CPLAY MID”.
4. Press the [REC/REC MODE] button when “C1
= AD = ”
is displayed.
5. Press the u (MD) or x (MD) button to display “FBIAS
ADJUST”.
/ a = ”.
6. Press the [RADIO/BAND] button to display “
The first four digits indicate the C1 error rate, the two digits
after [/] indicate ADER, and the 2 digits after [a =] indicate the
focus bias value.
7. Turn the JOG dial clockwise and find the focus bias value at
which the C1 error rate becomes about 200 (Refer to Note 2).
8. Press the [RADIO/BAND] button to display “
/ b = ”.
9. Press the u (MD) or x (MD) button counterclockwise and
find the focus bias value at which the C1 error rate becomes
about 200.
10. Press the [RADIO/BAND] button to display “
/ c = ”.
11. Check that the C1 error rate is below 50 and ADER is 00. Then
press the [RADIO/BAND] button.
12. If the “( )” in “ ( )” is above 20, press the
[RADIO/BAND] button.
If below 20, press the [REC/REC MODE] button and repeat the
adjustment from step 2.
13. Press the Z (MD) button and take out the disc.
Note 1: The relation between the C1 error and focus bias is as shown in
the following figure. Find points A and B in the following figure
using the above adjustment. The focal point position C is automatically calculated form points A and B.
Note 2: As the C1 error rate changes, perform the adjustment using the
average value.
C1 error
about
200
B
C
A
Focus bias value
(F. BIAS)
11. ERROR RATE CHECK
11-1. CD Error Rate Check
Checking Procedure:
1. Load the check disc (MD) TDYS-1.
2. Press the u (MD) or x (MD) button and display “CPLAY
MODE”.
3. Press the [RADIO/BAND] button twice and display “CPLAY
MID”.
4. The display changes to “C1
= AD = ”.
5. Check that the C1 error rate is below 20.
6. Press the [REC/REC MODE] button to stop playback, then press
the Z (MD) button and take out the check disc.
11-2. MO Error Rate Check
Checking Procedure:
1. Load the continuously-recorded disc. (Refer to “5. CREATING
CONTINUOUSLY-RECORDED DISC”)
2. Press the u (MD) or x (MD) button to display “CPLAY
MODE”.
3. Press the [RADIO/BAND] button to display “CPLAY MID”.
4. The display changes to “C1
= AD = ”.
5. If the C1 error rate is below 50, check that ADER is 00.
6. Press the [REC/REC MODE] button to stop playback, then press
the Z (MD) button and take out the test disc.
12. FOCUS BIAS CHECK
Change the focus bias and check the focus tolerance amount.
Checking Procedure:
1. Load the continuously-recorded disc. (Refer to “5. CREATING CONTINUOUSLY-RECORDED DISC”)
2. Press the u (MD) or x (MD) button to display “CPLAY
MODE”.
3. Press the [RADIO/BAND] button twice to display “CPLAY MID”.
4. Press the [REC/REC MODE] button when “C1
= AD = ”
is displayed.
5. Press the u (MD) or x (MD) button to display “FBIAS
CHECK”.
6. Press the [RADIO/BAND] button to display “
/ c = ”.
The first four digits indicate the C1 error rate, the two digits
after [/] indicate ADER, and the 2 digits after [c =] indicate the
focus bias value.
Check that the C1 error is below 50 and ADER is below 2.
7. Press the [RADIO/BAND] button and display “
/ b = ”.
Check that the C1 error is about 200 and ADER is below 2.
8. Press the [RADIO/BAND] button and display “
/ a = ”.
Check that the C1 error is about 200 and ADER is below 2.
9. Press the [REC/REC MODE] button, then press the Z (MD)
button and take out the disc.
Note 1: If the C1 error and ADER are above other than the specified value
at points A (step 8. in the above) or B (step 7. in the above), the
focus bias adjustment may not have been carried out properly.
Adjust perform the beginning again.
– 29 –
Adjustment Location:
– BD BOARD (COMPONENT SIDE) –
CN101
D101
GND
I+3V
IOP
CN110
TEO
RF
VC
NOTE
IC171
– BD BOARD (CONDUCTOR SIDE) –
IC101
IC121
IC192
Note: It is useful to use the jig for checking the waveform. (Refer to Servicing Notes on page 5)
– 30 –
5-3. CD SECTION
Display
Set the CD test mode when performing confirmations.
After completing the confirmation, release the CD test mode.
88
In the CD test mode, the set works as following sequence.
XX
XX XXX
CD test mode sequence:
1. Enter the CD test mode
(STOP mode 1)
2. STOP Mode 2
1. Press the x (CD) button to enter the STOP mode 2, and display as below.
Display
Press the x (CD)
button.
2. STOP mode 2
88
07
00 3A0
Press the [u, CD]
button.
Press the x (CD)
button.
2. Press the > and . button to move the optical pick-up to
position of the track where signal is recorded.
3. FOCUS mode
Press the [u, CD]
button.
4. ALL SERVO
ON mode 2
3. FOCUS Mode (Traverse Confirmation)
1. Press the u button to enter the FOCUS mode and display as
below. (Focus servo ON. CLV-S, tacking and sled servo OFF)
Press the x (CD)
button.
Display
Press the [u, CD]
button.
5. TRACKING
GAIN UP mode 1
11
Press the x (CD)
button.
Press the [u, CD]
button.
6. TRACKING
GAIN UP mode 2
00 3A0
2. Connect an oscilloscope to TP (TEO) and TP (VC) on the CD
board.
Press the x (CD)
button.
Connection:
oscilloscope
(DC range)
Press the [u, CD]
button.
7. ALL SERVO
ON mode1
07
CD board
Press the x (CD)
button.
TP (TEO)
TP (VC)
+
–
3. Confirm that the traverse level of waveform satisfy specified
value as follows.
Press the [u , CD]
button.
Traverse Waveform
Note 1: ALL SERVO ON mode 1 and TRACKING GAIN UP mode 1:
LPC ON (lights up “ALL” indication)
ALL SERVO ON mode 2 and TRACKING GAIN UP mode 2:
LPC OFF (Does not lights up “ALL” indication)
*) LPC: Laser power control
Note 2: TRACKING GAIN UP mode 1, 2 is not used in servicing.
1. Entering the CD Test Mode
Press the [POWER] button to turn the power ON.
Open the disc lid, and put a disc.
Close the disc lid.
Press the [POWER] button to standby state.
Press the button [EDIT], [SOUND] and > (CD) simultaneously.
6. After display “CD” for a few seconds, enter the CD test mode
(STOP mode 1), and display as below.
1.
2.
3.
4.
5.
A
VC
B
A=B
Specified Value:
traverse level: 160 to 380 mVp-p
Connecting Location: CD board (See page 32)
– 31 –
traverse level:
160 to 380 mVp-p
4. ALL SERVO ON Mode 1
6. Releasing the CD Test Mode
(RF Level and Jitter Confirmation 1)
1. Press the u button four times to enter the ALL SERVO ON
mode 1 (start playback the disc) and display as below.
(All servo ON. LPC ON)
1. Press the x (CD) button to stop rotate the disc.
2. Press the [POWER] button to release the CD test mode and turn
to standby state.
Display
Connecting Location:
ALL
21
07
CD BOARD (CONDUCTOR SIDE)
00 3A0
2. Connect an oscilloscope to TP (RFO) and TP (VC) on the CD
board.
Connection:
oscilloscope
(DC range)
CD board
TP(VC)
TP (RFO)
TP (VC)
+
–
TP(TEO)
TP(RFO)
3. Confirm that the RF level and jitter of waveform satisfy specified values as follows.
RF signal Waveform
VOLT/DIV: 50 mV
TIME/DIV: 500 ns
RF level:
1.0 to 1.4 Vp-p
Specified Values:
RF level : 1.0 to 1.4 Vp-p
jitter
: less than 9 nsec
Connecting Location: CD board
5. ALL SERVO ON Mode 2
(RF Level and Jitter Confirmation 2)
1. Press the u button to enter the LPC OFF mode and display
as below. (All servo ON. LPC OFF)
Display
21
07
00 3A0
2. Confirm that the RF level and jitter of waveform satisfy specified values as follows.
Specified Values:
RF level : 0.8 to 1.4 Vp-p
jitter
: less than 9 nsec
If the RF level and jitter are out of specified values, measure
again after clean the object lens by an applicator with lens cleaning liquid.
– 32 –
SECTION 6
DIAGRAMS
6-1. IC PIN FUNCTION DESCRIPTIONS
• BD BOARD IC101 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP)
Pin No.
Pin Name
I/O
1
I
I
I-V converted RF signal I input from the optical pick-up block detector
Pin Description
2
J
I
I-V converted RF signal J input from the optical pick-up block detector
3
VC
O
Middle point voltage (+ 1.65 V) generation output terminal
4–9
A–F
I
Signal input from the optical pick-up detector
10
PD
I
Light amount monitor input from the optical pick-up block laser diode
11
APC
O
Laser amplifier output terminal to the automatic power control circuit
12
APCREF
I
13
GND
—
Reference voltage input terminal for setting laser power
Ground terminal
14
TEMPI
I
Connected to the temperature sensor
15
TEMPR
O
Output terminal for a temperature sensor reference voltage
16
SWDT
I
Writing serial data input from the CXD2654R (IC121)
17
SCLK
I
Serial data transfer clock signal input from the CXD2654R (IC121)
18
XLAT
I
Serial data latch pulse signal input from the CXD2654R (IC121)
19
XSTBY
I
Standby signal input terminal
20
F0CNT
I
21
VREF
O
Reference voltage output terminal
22
EQADJ
I
Center frequency setting terminal for the internal circuit (EQ)
23
3TADJ
I
24
VCC
—
25
WBLADJ
I
Center frequency setting terminal for the internal circuit (BPF22)
26
TE
O
Tracking error signal output to the CXD2654R (IC121)
27
CSLED
I
Connected to the external capacitor for low-pass filter of the sled error signal
28
SE
O
Sled error signal output to the CXD2654R (IC121)
29
ADFM
O
FM signal output of the ADIP
30
ADIN
I
Receives a ADIP FM signal in AC coupling
31
ADAGC
I
Connected to the external capacitor for ADIP AGC
32
ADFG
O
ADIP duplex signal (22.05 kHz ± 1 kHz) output to the CXD2654R (IC121)
33
AUX
O
Auxiliary signal (I3 signal/temperature signal) output to the CXD2654R (IC121)
34
FE
O
Focus error signal output to the CXD2654R (IC121)
“L”: standby (fixed at “H” in this set)
Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ) input
from the CXD2654R (IC121)
Not used (open)
Center frequency setting terminal for the internal circuit (BPF3T)
Power supply terminal (+3.3V)
35
ABCD
O
Light amount signal (ABCD) output to the CXD2654R (IC121)
36
BOTM
O
Light amount signal (RF/ABCD) bottom hold output to the CXD264R (IC121)
37
PEAK
O
Light amount signal (RF/ABCD) peak hold output to the CXD2654R (IC121)
38
RF
O
Playback EFM RF signal output to the CXD2654R (IC121)
39
RFAGC
I
Connected to the external capacitor for RF auto gain control circuit
40
AGCI
I
Receives a RF signal in AC coupling
41
COMPO
O
User comparator output terminal
42
COMPP
I
User comparator input terminal
43
ADDC
I
Connected to the external capacitor for cutting the low band of the ADIP amplifier
44
OPO
O
User operational amplifier output terminal
45
OPN
I
User operational amplifier inversion input terminal
46
RFO
O
RF signal output terminal
Not used (open)
Not used (fixed at “L”)
47
MORFI
I
Receives a MO RF signal in AC coupling
48
MORFO
O
MO RF signal output terminal
– 33 –
Not used (open)
Not used (fixed at “L”)
• BD BOARD IC121 CXD2654R
(DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO SIGNAL PROCESSOR, EFM/ACIRC ENCODER/DECODER,
SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER)
Pin No.
Pin Name
I/O
Pin Description
Focus OK signal output to the MD mechanism controller (IC601)
1
MNT0 (FOK)
O
2
MNT1 (SHOCK)
O
3
MNT2 (XBUSY)
O
Busy monitor signal output to the MD mechanism controller (IC601)
4
MNT3 (SLOCK)
O
Spindle servo lock status monitor signal output to the MD mechanism controller (IC601)
5
SWDT
I
6
SCLK
I (S)
Serial data transfer clock signal input from the MD mechanism controller (IC601)
7
XLAT
I (S)
Serial data latch pulse signal input from the MD mechanism controller (IC601)
8
SRDT
O (3)
Reading serial data signal output to the MD mechanism controller (IC601)
“H” is output when focus is on (“L”: NG)
Track jump detection signal output to the MD mechanism controller (IC601)
Writing serial data signal input from the MD mechanism controller (IC601)
9
SENS
O (3)
Internal status (SENSE) output to the MD mechanism controller (IC601)
10
XRST
I (S)
Reset signal input from the MD mechanism controller (IC601)
11
SQSY
O
12
DQSY
O
13
RECP
I
14
XINT
O
15
TX
I
16
OSCI
I
17
OSCO
O
“L”: reset
Subcode Q sync (SCOR) output to the MD mechanism controller (IC601)
“L” is output every 13.3 msec
Almost all, “H” is output
Digital In U-bit CD format subcode Q sync (SCOR) output to the MD mechanism controller
(IC601)
“L” is output every 13.3 msec
Almost all, “H” is output
Laser power selection signal input from the MD mechanism controller (IC601)
“L”: playback mode, “H”: recording mode
Interrupt status output to the MD mechanism controller (IC601)
Recording data output enable signal input from the MD mechanism controller (IC601)
Writing data transmission timing input (Also serves as the magnetic head on/off output)
System clock signal (512 Fs = 22.5792 MHz) input terminal
System clock signal (512 Fs = 22.5792 MHz) output terminal
Not used (open)
Input terminal for the system clock frequency setting
18
XTSL
I
19
DIN0
I
Digital audio signal input terminal when recording mode (for digital optical input)
20
DIN1
I
Digital audio signal input terminal when recording mode (for digital optical input)
21
DOUT
O
22
DATAI
I
“L”: 45.1584 MHz, “H”: 22.5792 MHz (fixed at “H” in this set)
Digital audio signal output terminal when playback mode (for digital optical output)
Not used
Serial data input terminal
Not used (fixed at “L”)
23
LRCKI
I
L/R sampling clock signal (44.1 kHz) input terminal
24
XBCKI
I
Bit clock signal (2.8224 MHz) input terminal
Not used (fixed at “L”)
25
ADDT
I
Recording data input from the A/D, D/A converter (IC603)
26
DADT
O
Playback data output to the A/D, D/A converter (IC603)
27
LRCK
O
L/R sampling clock signal (44.1 kHz) output to the A/D, D/A converter (IC603)
28
XBCK
O
Bit clock signal (2.8224 MHz) output to the A/D, D/A converter (IC603)
Not used (fixed at “L”)
29
FS256
O
Clock signal (11.2896 MHz) output terminal
30
DVDD
—
Power supply terminal (+3.3 V) (digital system)
31 – 34
A03 – A00
O
Address signal output to the D-RAM (IC124)
35
A10
O
Address signal output to the external D-RAM
36 – 40
A04 – A08
O
Address signal output to the D-RAM (IC124)
41
A11
O
Address signal output to the external D-RAM
42
DVSS
—
Ground terminal (digital system)
43
XOE
O
Output enable signal output to the D-RAM (IC124)
44
XCAS
O
Column address strobe signal output to the D-RAM (IC124)
45
A09
O
Address signal output to the D-RAM (IC124)
– 34 –
Not used (open)
Not used (open)
Not used (open)
“L” active
“L” active
Not used
Pin No.
Pin Name
I/O
46
XRAS
O
Row address strobe signal output to the D-RAM (IC124)
Pin Description
47
XWE
O
Write enable signal output to the D-RAM (IC124)
48
D1
I/O
49
D0
I/O
50
D2
I/O
“L” active
“L” active
Two-way data bus with the D-RAM (IC124)
51
D3
I/O
52
MVCI
I (S)
53
ASYO
O
54
ASYI
I (A)
55
AVDD
—
56
BIAS
I (A)
Playback EFM asymmetry circuit constant current input terminal
57
RFI
I (A)
Playback EFM RF signal input from the CXA2523AR (IC101)
58
AVSS
—
59
PCO
O (3)
Phase comparison output for master clock of the recording/playback EFM master PLL
60
FILI
I (A)
Filter input for master clock of the recording/playback master PLL
61
FILO
O (A)
Filter output for master clock of the recording/playback master PLL
62
CLTV
I (A)
Internal VCO control voltage input of the recording/playback master PLL
Digital in PLL oscillation input from the external VCO
Not used (fixed at “L”)
Playback EFM full-swing output terminal
Playback EFM asymmetry comparator voltage input terminal
Power supply terminal (+3.3 V) (analog system)
Ground terminal (analog system)
63
PEAK
I (A)
Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC101)
64
BOTM
I (A)
Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC101)
65
ABCD
I (A)
Light amount signal (ABCD) input form the CXA2523AR (IC101)
66
FE
I (A)
Focus error signal input from the CXA2523AR (IC101)
67
AUX1
I (A)
Auxiliary signal (I3 signal/temperature signal) input from the CXA2523AR (IC101)
68
VC
I (A)
Middle point voltage (+1.65 V) input from the CXA2523AR (IC101)
69
ADIO
O (A)
Monitor output of the A/D converter input signal
70
AVDD
—
Power supply terminal (+3.3 V) (analog system)
Not used (open)
71
ADRT
I (A)
A/D converter operational range upper limit voltage input terminal (fixed at “H” in this set)
72
ADRB
I (A)
A/D converter operational range lower limit voltage input terminal (fixed at “L” in this set)
73
AVSS
—
74
SE
I (A)
Ground terminal (analog system)
Sled error signal input from the CXA2523AR (IC101)
75
TE
I (A)
Tracking error signal input from the CXA2523AR (IC101)
76
DCHG
I (A)
Connected to the +3.3 V power supply
77
APC
I (A)
Error signal input for the laser automatic power control
78
ADFG
I (S)
ADIP duplex FM signal (22.05 kHz ± 1 kHz) input from the CXA2523AR (IC101)
79
F0CNT
O
Filter f0 control signal output to the CXA2523AR (IC101)
80
XLRF
O
Serial data latch pulse signal output to the CXA2523AR (IC101)
81
CKRF
O
Serial data transfer clock signal output to the CXA2523AR (IC101)
82
DTRF
O
Writing serial data output to the CXA2523AR (IC101)
83
APCREF
O
84
LDDR
O
PWM signal output for the laser automatic power control
85
TRDR
O
Tracking servo drive PWM signal (–) output to the BH6511FS (IC152)
Not used (fixed at “H”)
Control signal output to the reference voltage generator circuit for the laser automatic power
control
Not used (open)
86
TFDR
O
Tracking servo drive PWM signal (+) output to the BH6511FS (IC152)
87
DVDD
—
Power supply terminal (+3.3 V) (digital system)
88
FFDR
O
Focus servo drive PWM signal (+) output to the BH6511FS (IC152)
89
FRDR
O
Focus servo drive PWM signal (–) output to the BH6511FS (IC152)
90
FS4
O
Clock signal (176.4 kHz) output terminal (X’tal system)
– 35 –
Not used (open)
Pin No.
Pin Name
I/O
91
SRDR
O
Sled servo drive PWM signal (–) output to the BH6511FS (IC152)
Pin Description
92
SFDR
O
Sled servo drive PWM signal (+) output to the BH6511FS (IC152)
93
SPRD
O
Spindle servo drive PWM signal (–) output to the BH6511FS (IC152)
94
SPFD
O
Spindle servo drive PWM signal (+) output to the BH6511FS (IC152)
95
FGIN
I (S)
96
TEST1
I
97
TEST2
I
98
TEST3
I
99
DVSS
—
Ground terminal (digital system)
100
EFMO
O
EFM signal output terminal when recording mode
Input terminal for the test (fixed at “L”)
* I (S) stands for schmitt input, I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.
– 36 –
• MAIN BOARD IC401 CXP740096-044Q (SYSTEM CONTROL)
Pin No.
Pin Name
I/O
1
NC
—
Not used
Pin Description
2
MEGA BASS
O
MEGA BASS on/off control signal output
3
LINE-LEVEL
O
Line in level control signal output
4
AU-CS
O
Chip select signal output to the electrical volume (IC301)
5
AU-DATA
O
Serial data output to the electrical volume (IC301)
6
AU-CLK
O
Serial data transfer clock signal output to the electrical volume (IC301)
7
RDS-DATA
I
RDS serial data input from the RDS decoder
8
NC
—
“L”: MEGA BASS on
“L”: normal, “H”: high
(Not used)
Not used
9
RDS-CLK
I
RDS serial data transfer clock signal input from the RDS decoder
10
TU-MUTE
O
Muting on/off control signal output for the tuner signal
(Not used)
11
TU-CE
O
PLL serial chip enable signal output to the tuner PLL IC (IC2)
12
TU-DATA
O
PLL serial data output to the tuner PLL IC (IC2)
13
TU-CLK
O
PLL serial data transfer clock signal output to the tuner PLL IC (IC2)
14
TU-COUNT
I
PLL serial data input from the tuner PLL IC (IC2)
15
CD-DOOR
I
Detection signal input from the CD lid open/close detect switch (S402)
16
NC
—
“H”: muting on
Not used
17 – 21
KEY S4 – S0
I
Key input terminal
22
LED-CHARA-KAN
O
LED (LED board D609) on/off drive signal output
23
LED-123
O
LED (LED board D610-613) on/off drive signal output
24
LED-456
O
LED (LED board D607,615-617) on/off drive signal output
25
LED-789
O
LED (LED board D618-621) on/off drive signal output
26
LED-0
O
LED (LED board D622-625) on/off drive signal output
27
LED-CHARA-ABC
O
LED (LED board D608) on/off drive signal output
28
NC
—
Not used
29
LED-CLOCK
O
LED (LED board D602-614) on/off drive signal output
30
LED-HISPEED
O
LED (LED board D601) on/off drive signal output
31
RA-POWER
O
RA7V power supply on/off control signal output
32
NC
—
Not used
33
FL-CTR
O
FL-BU3.3V power supply on/off control signal output
34
PA-STANDBY
O
Power amplifier on/off control signal output
35
LINE-MUTE
O
LINE input muting on/off control signal output
36
KEY-C2
O
Not used
37
KEY-C1
O
Not used
38
FL-DIM
O
Control signal output for the brightness of fluorescent tube display
39
TU-SFT
O
Frequency shift of the main system clock control terminal
40
RST
I
System reset signal input from the reset signal generator (IC403)
41
VSS
—
42
XTAL
I
“H”: power off “H”: standby, “L”: power on
“L”: reset
Ground terminal
Main system clock input terminal (8 MHz)
43
EXTAL
O
Main system clock input terminal (8 MHz)
44
FL-RST
O
Reset signal output to the fluorescent tube display drive IC (IC601)
45
FL-CS
O
Chip enable signal output to the fluorescent tube display drive IC (IC601)
46
FL-DATA
O
Serial data output to the fluorescent tube display drive IC (IC601)
Serial data transfer clock signal output to the fluorescent tube display drive IC (IC601)
47
FL-CLK
O
48
SELECT-GND
I/O
Destination setting terminal
49
SELECT
I
Destination setting terminal
50
NC
—
Not used
– 37 –
Fixed at “H” in this set
Pin No.
Pin Name
I/O
51
KEY-C4A
I
Pin Description
52
AVSS
—
Ground terminal (for A/D converter)
53
AVREF
—
Reference voltage (+3.3V) input terminal (for A/D converter)
54
AVDD
—
Power supply terminal (+3.3V) (for A/D converter)
55 – 58
KEY C3A – C0A
I
Key input terminal
Key input terminal
59
3.3V-SHORT
I
AU 7.5V short test pin
60 – 62
KEY AD2 – AD0
I
Key input terminal (A/D input) (TOP board)
63
MD-PDOWN
O
64
MD-SRTS
O
System controller busy status monitor output to the MD mechanism controller (IC601)
65
MD-SCTS
I
MD mechanism controller busy status monitor input from the MD mechanism controller (IC601)
66
MD-RST
O
67
MD-H
O
MD play control signal output to the A/D, D/A converter (IC603) “L”: MD playback mode
68
REC-H
O
MD REC control signal output to the A/D, D/A converter (IC603)
69
MD-SRXD
O
UART communication data input from the MD mechanism controller (IC601)
70
MD-STXD
I
UART communication data output to the MD mechanism controller (IC601)
71, 72
NC
—
Not used
73
CD-12/8
O
Servo setting when CD operates faster.
74
CD-HISPEED
O
CD higher speed setting
75
CD-POWER
O
CD servo system power supply on/off control signal output
76
CD-MUTE
O
Muting on/off control signal output for the CD playback signal
77
NC
—
Not used
78
CD-CSOR
I
Subcode sync (S0+S1) detection signal input from the CD DSP IC (IC702)
79
CD-SQSO
I
Subcode Q data input from the CD DSP IC (IC702)
80
CD-XRST
O
Reset signal output to the CD RF AMP (IC701), CD DSP IC (IC702)
81
CD-SQCK
O
Subcode Q data reading clock signal output to the CD DSP IC (IC702)
82
CD-SENSE1
I
Internal status (SENSE) input from the CD DSP IC (IC702)
83
CD-DATA
O
Serial data output to the CD DSP IC (IC702)
84
CD-XLAT
O
Serial data latch pulse signal output to the CD DSP IC (IC702)
85
RMC
I
Sircs remote control signal input from the remote control receiver (IC602)
86
TEX
O
Sub system clock output terminal (32.768 kHz)
87
TX
I
Sub system clock input terminal (32.768 kHz)
88
VSS
—
Ground terminal
89
VDD
—
Power supply terminal (+3.3V)
90
NC
—
Not used
91
CD-CLK
O
Serial data transfer clock signal output to the CD DSP IC (IC702)
92
CD-SENSE2
I
Internal status (SENSE) input from the CD DSP IC (IC702)
93
CD-FOK
I
Focus OK signal input terminal
94
STBY-CTR
O
Power saving mode selection
95
ACCHK
I
AC power supply detection signal input
96
NC
—
Not used
97
PCON
O
Power on/off control signal output
98
AMUTE
O
Audio muting on/off control signal output
99
TU-LED
I
Input the signal for band tuning check from the tuner IC.
100
NC
—
Power down signal output to the MD mechanism controller (IC601)
“L”: remove the AC
power cord
Power supply on/off control signal output for the MD mechanism controller (IC601)
”H”: power on
Not used
– 38 –
“L”: MD recording mode
“H”: power on
“H”: muting on
(Not used (open))
“H”: normal, “L”: Power saving mode
“L”: AC in
“L”: standby mode, “H”: power on
“L”: muting on
• DG BOARD IC601 RU8X13MF-0102 (MD MECHANISM CONTROLLER)
Pin No.
Pin Name
I/O
1, 2
DAOUT0, DAOUT1
O
Not used (open)
3–5
KEY0 – KEY2
I
Key input terminal (A/D input)
6
CHACK-IN
I
7
PACK-IN
I
Pin Description
Not used (fixed at “H”)
Detection input from the disc chucking-in detect switch
“L: chucking
Not used (fixed at “H”)
Detection input from the loading-in detect switch
“L” at a load-out position, others: “H”
Not used (fixed at “H”)
Detection input from the loading-out detect switch (S602)
8
PACK-OUT
I
9, 10
NC
—
11
AVSS
—
12
XINT
I
Interrupt status input from the CXD2654R (IC121)
13
PDOWN
I
Power down detection signal input terminal
14
NC
—
15
SQSY
I
16
DQSY
I
17 – 19
NC
—
20
SYS-RST
I
21
TEST
I
22
+3.3V
—
23
VBAT
I
24
XOUT-T
O
Sub system clock output terminal (32.768 kHz)
25
XIN-T
I
Sub system clock input terminal (32.768 kHz)
26
GND
—
Ground terminal
27
XOUT
O
Main system clock output terminal (12 MHz)
28
XIN
I
Main system clock input terminal (12 MHz)
29
EXMEM
I
30
S1
—
Not used (open)
31
NC
—
Not used (fixed at “L”)
32
SENS
I
Internal status (SENSE) input from the CXD2654R (IC121)
33
SHOCK
I
Track jump detection signal input from the CXD2654R (IC121)
34, 35
NC
—
Not used (fixed at “L”)
36
STB
O
Relay drive signal output for the power on/off
37
REC P
I
Detection input from the recording position detect switch (S601)
“L” active
38
PB P
I
Detection input from the playback position detect switch (S604)
“L” active
“L” at a load-out position, others: “H”
Not used (fixed at “L”)
Ground terminal
“L”: power down, normally: “H”
Not used (fixed at “L”)
Subcode Q sync (SCOR) input from the CXD2654R (IC121)
“L” is input every 13.3 msec
Almost all, “H” is input
Digital In U-bit CD format subcode Q sync (SCOR) input from the CXD2654R (IC121)
“L” is input every 13.3 msec
Almost all, “H” is input
Not used (fixed at “L”)
System reset signal input from the reset switch (Q604)
“L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
Setting terminal for the test mode
Not used (fixed at “L”)
Power supply terminal (+3.3V)
Power supply for the internal real time clock and RAM
Setting terminal external ROM mode or internal ROM mode
“L”: internal ROM mode
(fixed at “L”)
“L”: standby mode, “H”: relay on
Loading motor drive voltage control signal output for the loading motor driver (IC602)
39
LD-LOW
O
40
NC
—
41
MNT2 (XBUSY)
I
Busy status signal input from the CXD2654R (IC121)
42
MNT3 (SLOCK)
I
Spindle servo lock status monitor signal input from the CXD2654R (IC121)
“H” active
Not used (open)
43
LED0
O
LED drive signal output terminal
44, 45
NC
—
Not used (fixed at “L”)
46
RST-LOW
—
Not used (open)
47
GND
—
Ground terminal
– 39 –
“L”: LED on
Not used (open)
Pin No.
Pin Name
I/O
48
+3.3V
—
Pin Description
Power supply terminal (+3.3V)
49
SNG/CHG
—
50, 51
JOG1, JOG0
I
Not used (fixed at “L”)
52
SDA
I/O
Two-way data bus with the EEPROM (IC171)
53
SCL
O
Clock signal output to the EEPROM (IC171)
54
2M/4M
I
55, 56
NC
—
57
RXD (UART)
I
UART communication data input from the system controller (IC401)
58
TXD (UART)
O
UART communication data output to the system controller (IC401)
59
RTS
I
RTS (Request To Send) input from the system controller (IC401)
JOG dial pulse input
Not used (fixed at “L”)
Select whether D-RAM capacitance 2M bit or 4M bit
“L”: 4M bit (external D-RAM), “H”:
2M bit (internal D-RAM of IC121 CXD2654R) (fixed at “H” in this set)
Not used (fixed at “L”)
60
CTS
O
CTS (Clear To Send) output to the system controller (IC401)
61, 62
AUBIT0, AUBIT1
—
Not used (fixed at “L”)
63, 64
CLKSET0,
CLKSET1
I
Clock destination setting terminal
65
GND
—
Ground terminal
66
+3.3V
—
Power supply terminal (+3.3V)
(fixed at “L”)
67
SCLK
O
Serial clock signal output to the CXD2654R (IC121)
68
SWDT
O
Writing data output to the CXD2654R (IC121)
69
SRDT
I
Reading data input from the CXD2654R (IC121)
70
EMP
O
Emphasis control signal output to the A/D, D/A converter (IC603) when recording mode
71
SCK1
O
Display serial clock signal output terminal
72
SOUT1
O
Display serial data output terminal
73
SIN1
O
Chip select signal output for the display
74
CSB
I
Not used (fixed at “H”)
75
LDON
O
Laser diode on/off control signal output to the automatic power control circuit
76
PIT/GRV
O
Not used (open)
Not used (open)
Not used (open)
“H”: is output for the playback only disc or TOC area
Not used (open)
Focus OK signal input from the CXD2654R (IC121)
77
FOK
I
78
NC
—
Not used (open)
79
LOCK
O
Lock signal output terminal
“H” is input when focus is on (“L”: NG)
Not used (open)
Laser power select signal output to the CXD2654R (IC121) and HF module switch circuit
80
WRPWR
O
81
DIG-RST
O
82
NC
—
Not used (open)
83
DA-RST
O
Reset signal output to the A/D, D/A converter (IC603)
84
DSEL-A
—
Not used (open)
85
DSEL-B
—
Not used (open)
“L”: playback mode, “H”: recording mode
Reset signal output to the CXD2654R (IC121) and BH6511FS (IC152)
“L”: reset
Laser modulation select signal output to the HF module switch circuit
Stop: “L”, Playback power: “H”,
Recording power:
0.5 sec
86
MOD
“H”: laser on
Pit/groove detection signal output terminal
O
2 sec
– 40 –
“L”: reset
Pin No.
Pin Name
I/O
87
REC/PB
O
Not used (open)
Pin Description
88
NC
—
Not used (open)
Recording data output enable signal output to the CXD2654R (IC121) and overwrite head
89
SCTX
O
driver (IC181)
Writing data transmission timing output (Also serves as the magnetic head
on/off output)
90
XLATCH
O
Serial data latch pules signal output to the CXD2654R (IC121)
91, 92
NC
—
Not used (open)
93
AMUTE
O
Muting control signal output terminal
94
LDOUT
O
Motor control signal output to the loading motor driver (IC602)
“L” active
*1
95
LDIN
O
Motor control signal output to the loading motor driver (IC602)
“L” active
*1
Detection input from the sled limit-in detect switch (S101)
96
LIMIT-IN
I
97
PROTECT
I
98
REFLECT
I
99
GND
—
Ground terminal
100
+3.3V
—
Power supply terminal (+3.3V)
The optical pick-up is inner position when “L”
Rec-proof claw detect input from the protect detect switch (S102-2)
Detection input from the disc reflection rate detect switch (S102-1)
“L”: high reflection rate disc, “H”: low reflection rate disc
*1 Loading motor (M103) control
Mode
LOADING
EJECT
BRAKE
RUN IDLE
LDIN (pin og)
“L”
“H”
“L”
“H”
LDOUT (pin of)
“H”
“L”
“L”
“H”
Terminal
Not used (open)
– 41 –
“H”: write protect
6-2. CIRCUIT BOARDS LOCATION
LED board
TOP board
POWER board
SW board
BATTERY (+) board
BATTERY (–) board
KEY board
BD board
DG board
CD board
CD MOTOR board
MAIN board
FL board
TUNER board
JACK board
– 42 –
ZS-M35
6-3. BLOCK DIAGRAM — TUNER SECTION —
TUNER BOARD
L6
IF, DET, FM MPX
IC1 (2/2)
CT1,L1
FM
TRACKING
10
FM/AM FRONT-END
IC1 (1/2)
QUAD
ANT1
FL1
B.P.F
L2
FM
FREQUENCY
COVERAGE
2
L1
FM RF
24
D1
FM RF-IN
FM
MIX
MIX-OUT
CF1
4
7
FM
DET
CN1
AM/FM DET-OUT
16
BUFFER
15
MPX-IN
DIVIDE
DECODE
VCO
L-OUT
MUTE
R-OUT
2
12
11
RA-LCH
R-CH
FM RF OUT
CT1
L2
FM OSC
CF2
FM
IF-IN
AM IF
T1
21
FM OSC
CF3
FM
OSC
6
AM
IF-IN
AM
DET
D2
17
BAND
18
MO-ST
ST-IND
L3
AM ANT
AM
ANTENNA
IF-OUT
IF
BUFFER
TB1
14
13
D3
22
CT2, L3
AM
TRACKING
AM RF-IN
CT2
AM
MIX
PLL, LOW-PASS FILTER
IC2
OSC-OUT
L4
AM
FREQUENCY
COVERAGE
L4
AM
OSC
19
12
11
20
AM OSC
FM-IN
1/2
AM-IN
SWALLOW
COUNTER
1/16, 1/17
4BIT
12BITS
PROGRAMMABLE
DIVIDER
AM
OSC
A
16
17
PD
LP-IN
MAIN
SECTION
PHASE DETECTOR
CHARGE PUMP
(Page 51)
ST-IND
8
MO/ST
13
IF-IN
10
REFERENCE
DIVIDER
18
19
X1
75kHz
RADIO +B
20
LP-OUT
X IN
DATA SHIFT
REGISTER
LATCH
X OUT
BAND
7
2
CK
3
CD
CE
1
RD
CCB/IF
4
COUNT
6
CLK
7
DATA
8
CE
9
TU COUNT
RCLOCK
R DATA
R CE
04
• SIGNAL PATH
: FM
: AM
R-CH : Same as L-CH.
– 43 –
– 44 –
– 45 –
ZS-M35
6-4. BLOCK DIAGRAM — MD SECTION —
CN102
BD BOARD (1/2)
CN601
13
DG BOARD
CN104
FILTER
HR901
(OVER WRITE HEAD)
59
62
61
SCTX
17
ILCC
9
9
AUTOMATIC
POWER CONTROL
Q162, 163
11
TE
E
I-V
AMP
F
APC
TRACKING
ERROR AMP
V-I
CONVERTER
PD
12
CPU
INTERFACE
34
F0CNT
26
28
3
CN602
(1/4)
16 17 18
16
PSB
5
HF MODULE
FCS–
TRK+
TRK–
MOD
21 19
IN4F
4
83
SPRD
27 OUT2F
IN2F 29
92
25 OUT2R
IN2R 30
91
3
2
1
21 OUT1F
23 OUT1R
IN1F 19
IN1R 18
10
XRST
13
RECP
IN3F 14
IN3R 15
AUTOMATIC
POWER
CONTROL
SFDR
9
8
5 6 7
1 15 18 10 12
23
12
9
6 14 12
32 69 68 67 90
75 LDON
81 DIG-RST
80 WR-PWR
86 MOD
FFDR
88
FRDR
89
TFDR
86
TRDR
85
4
LOADING
MOTOR DRIVE
IC602
20 2 8 19
CN103
(1/5)
1, 2, 18, 19
XOE
43
XWE
47
XRAS
46
XCAS
44
16
3
4
17
XOE
XWE
XRAS
XCAS
1 2 3 4
DEMO
18
3
VINL
6
VINR
3
A/D
CONVERTER
LRCK
AD-LCH
R-CH
(Page 51)
SYSCK 9
PDDA PDAD
8
7
12
MD PLAY/REC
SWITCH
Q620
13
FROM CPU
INTERFACE
MD MECHANISM CONTROLLER
IC601
XLRF
80
CKRF
81
DTRF
82
XLAT
SCLK
SWDT
SW
IC606
2
RECP 37
CN605
(2/2) 3
3
5
5
7
7
8
REFERENCE
VOLTAGE SWITCH
Q611
6
CN602
(4/4)
39 LD-LOW
SDA 5
EEPROM
IC171
SCL 6
LIMIT-IN 96
REFLECT 98
27 XOUT
6
2
CN601
(2/2)
SW BOARD (2/2)
S601
(REC POSITION)
S602
(PACK OUT)
• SIGNAL PATH
S604
(PLAY POSITION)
: MD PLAY
PROTECT 97
8
: MD REC (DIGITAL)
BD BOARD (2/2)
CN103
(4/4)
16
B+
13
11
S102
-1
11
13
-2
S101
(LIMIT IN)
Q616
S102-1
(REFLECT RATE DETECT)
S102-2
(PROTECT DETECT)
B+
(+5V)
B+
SWITCH
Q617
B+
(AU +3.3V)
B+
SWITCH
Q612
B+
(D +5V)
R-CH : Same as L-CH.
MAIN BOARD (1/3)
25 XIN-T
CN601
(1/2)
X602
32.768kHz
RESET
SWITCH
Q604
SW BOARD (1/2)
3
22
2
PDOWN 13
CN602
(3/4)
RXD (UART) 57
52 SDA
TXD (UART) 58
53 SCL
RTS 59
CTS 60
– 47 –
12
STB 36
SYS-RST 20
M103
(LOADING)
21
CN404
(1/2)
Q610
24 XOUT-T
HF MODULE
SWITCH
IC103, Q102 – 104
1
: MD REC (ANALOG)
M
DIGITAL SERVO
SIGNAL PROCESSOR
IC121 (2/2)
7
IC605
512FS OSC
28 XIN
1
Q 5
B+
(D +5V)
X601
12MHz
2
1 CLK
EMP 70
DA-RST 83
1
1
7
77 33 41 42
CN605
(1/2)
CN103
(3/5)
– 46 –
C
MAIN
SECTION
4 22 16 5
5
7
A/D CONVERTER
DIGITAL SERVO
SIGNAL
PROCESS
DA-LCH
R-CH
X603
22.5792MHz
PACK-OUT
VREF
ANALOG MUX
SRDR
17
15
15
PBP 38
8
04
SQSY
10
DQSY
14
89
67 65 66 75 74 63 64
AUTO
SEQUENCER
12 OUT3F
10 OUT3R
26
7
17
FIN
OUT4R
4
17
1
OUT2
8
9
CN602
(2/4)
15
7
AUX1
ABCD
FE
TE
SE
PEAK
BOTM
3
APCREF
IN4R
19
5
7
(Page 50)
8
SERIAL
INTERFACE
BCK
10
3
D/A
CONVERTER
DIN
11
95 94
CN101 (2/2)
4
(FOCUS)
(TRACKING)
2-AXIS
DEVICE FCS+
M
OUT4F
14
23
SPFD
PWM GENERATOR
M102
(SLED)
M
6
15
12 11
20
CN103
(2/5)
M101
(SPINDLE)
MONITOR
CONTROL
SPINDLE
SERVO
16 15
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
IC152
12
CN604
(1/2)
VOUTL
19
VOUTR
20
DQ1 – DQ4
35
94 93
F0CNT
D0 – D3
INTERNAL BUS
SWDT
SCLK
XLAT
10
SERIAL/PARALLEL
CONVERTER,
DECODER
APCREF
LASER ON
SWITCH
Q101
SE
COMMAND
LD/PD
AMP
LASER DIODE
6
78
79
8
LD
PD
FE
FOCUS
ERROR AMP
DOUT
B
D-IN
CD
SECTION
D-RAM
IC124
A0 – A9
F
ABCD
ABCD
AMP
I-V
AMP
32
17
6 – 9, 11 – 15, 5
18
19
20
30
FOK
SHOCK
XBUSY
SLOCK
PD
C
D
E
29
DIVIDER
IC123
16
49, 48, 50, 51
DETECTOR
B.P.F.
ADIP
DEMODULATOR/
DECODER
A00 – A09
4
5
6
7
E
A
B
C
D
ADFG
21
OSCO
FOK
SHOCK
MNT2 (XBUSY)
MNT3 (SLOCK)
14
ADIN
DOUT
SUBCODE
PROCESSOR
SCLK
XLATCH
A
ADFM
36
SWDT
AT
AMP
20
CLOCK
GENERATOR
SWDT
SCLK
XLAT
WBL
J
19
DIN1
RIN
A
21
DIGITAL SIGNAL PROCESSOR,
EFM/ACIRC ENCODER/DECODER,
SHOCK PROOF MEMORY CONTROLLER,
ATRAC ENCODER/DECODER
IC121 (1/2)
OSCI
37
OUT1
B
BOTM
SPFD
C
D
EQ
3T
WBL
I
PEAK &
BOTTOM
SRDT
TEMP
1
B+
(+5V)
2
33
SRDT
PEAK
3T
12
DADT
26
XBCK
28
LRCK
27
FS256
29
COMPARATOR
RFI
SENS
13
57
SENS
AUX
F
B
38
14
D/A, A/D
CONVERTER
IC603
23
DIN0
DIGITAL
AUDIO
INTERFACE
EQ
WBL
B.P.F.
RF
8
10
1
34 – 31, 36 – 40, 45
RF AGC
& EQ
3
24
MNT0
MNT1
MNT2
MNT3
AGCI
XINT
40
XBCKI
LDOUT
46
XINT
RFO
XT
RF AMP
J
MD B+
(+3.3V)
22
+3.3V
REG
IC192
15
ASYI
SCTX
2
I
ASYO
25
DATAI
LRCKI
LDIN
1
54
FILO
SQSY
12
53
PLL
CLTV
DQSY
J
RF AMP,
FOCUS/TRACKING ERROR AMP
IC101
SAMPLING
RATE
CONVERTER
PCO
ADFG
I
CN101 (1/2)
16
MORFO
OPTICAL PICK-UP BLOCK
(KMS-260B)
47
MORFI
48
FILI
ATRAC
ENCODER/DECODER
60
ADDT
SHOCK PROOF
MEMORY CONTROLLER
100
EFMO
SPRD
1
EFM/ACIRC
ENCODER/DECODER
OVER WRITE
HEAD DRIVE
IC181, Q181, 182
CN603
LEVEL
SHIFT
IC604
9
B+
(+3.3V)
B+
SWITCH
Q603
B+
(BU +3.3V)
13
CN604
(2/2)
21
21
26
26
22
22
23
23
24
24
25
25
– 48 –
SYSTEM
CONTROLLER
IC401(1/3)
68 REC-H
67 MD-H
66 MD-RST
63 MD-PDOWN
70 MD-STXD
69 MD-SRXD
65 MD-SCTS
64 MD-SRTS
ZS-M35
6-5. BLOCK DIAGRAM — CD SECTION —
CD BOARD
46 VC
PD1
36
RF AMP
10
+
–
13
+
–
14
–
+
FOK
39
38
AUTOMATIC
POWER
CONTROL
Q701
7
34
E
35
18
ADRESS
DECODER
OUTPUT
DECODER
LD
TRACKING PHASE
COMPENSATION
PD
12
FOK
4
F+
2
DATA
20
XLT
19
CLK
18
XRST
21
TTL
IIL
DATO
12
XLTO
13
CLKO
14
79 XRST
1
CN801(1/2)
SL– 9
FIN
4
18
10
SLIN
3
17
SL–
2
MUTE
CN801(2/2)
15 OUT4+
M
IN4 27
16 OUT4MUTE4 26
04
CPU
I/F
MAIN BOARD (2/3)
R-CH
17
CN403
(1/2)
17
SCOR
57
SENS
6
SQSO
5
16
16
12
15
12
15
SQCK
4
XLAT
8
CLOK
9
DATA
7
13
13
10
9
10
9
11
11
1
1
2
2
SYSTEM
CONTROLLER
IC401(2/3)
76 CD MUTE
62
78 CD SCOR
82 CD SENSE1
79 CD SQSO
81
84
91
83
CD SQCK
CD XLAT
CD CLK
CD DATA
XTAI 70
X701
33.8688MHz
DIGITAL
CLV
XTAO 71
15
21
74 CD-HI SPEED
73 CD-12/8
15
7
7
14
8
18
14
8
18
73
80
92
75
CD-FOK
CD-XRST
CD SENSE2
CD POWER
REG
IC704
CD7V
HIGH SPEED
MUTE
Q705
3
HIGH SPEED
CONTROL
Q801-804
1
SERVO
CONTROL
2
BUFFER
IC801
MUTE
Q805
19
CD MOTOR BOARD
19
7
LIMIT
SPINDLE MOTOR DRIVE
IC802
10
76
SL+
MUTE DRIVE
M801
(SPINDLE)
AOUT2
PWM
25
F+
M
S801
(LIMIT)
MAIN
SECTION
D
CN703
SL+ 8
M802
(SLED)
1
EMPHI
3.3V
F–
CD LCH
(Page 51)
SYSM
FOCUS PHASE
COMPENSATION
5
5
65
SERIAL
I/F
T–
(FOCUS)
F-
55
AOUT1
PWM
TIN
LEVEL
SHIFT
(TRACKING)
26
54
BCKI
44
PCMDI
42
LRCKI
40
T+
LEVEL
SHIFT
T-
2
27
(Page 48)
SUB CODE
PROCESSOR
17
LEVEL
SHIFT
T+
BCK
43
PCMD
41
LRCK
39
EMPH
CNIN
11
SEIN
10
TRACKING/FOCUS COIL DRIVE,
SLED MOTOR DRIVE
IC703
3
D/A
I/F
CLV
SERVO
F
TA O
15
25
35
INPUT SHIFT,
REGISTER
APC
PD
TTL
FE AMP
31
C.OUT
22
SENS1
23
SENS2
24
IIL
ILL DATA
REGISTER
9
LD
PD2
EFM
DEMO.
RF
SL O
–
+
37
FE O
11
MD
SECTION
B
CN702
RFO
–
+
D-OUT
DIGITAL SIGNAL PROCESSOR,
CLV SERVO, D/A CONVERTER
IC702
SPOA
12
1
53
RF H 32
VC
16
+
–
DOUT
MDP
CN701
CN705
RF AMP, FOCUS/TRACKING SERVO
IC701
XLON
OPTICAL PICK-UP
BLOCK
(KSS-213C)
POWER
CONTROL
Q806,807
CN706
3
3
CD12CM
5
5
MDP
6
6
MUTE
4
4
PCON
CD 6V
R-CH : Same as L-CH.
• SIGNAL PATH
: CD PLAY
: MD REC (DIGITAL)
– 49 –
– 50 –
ZS-M35
6-6. BLOCK DIAGRAM — AUDIO SECTION —
CN403(2/2)
D
(Page 50)
20
21
22
27
CN404(2/2)
DA LCH
8
REC AMP
IC303
C
POWER AMP
IC301
OUT2
18
TONE/VOL
MEGA BASS
IC305,Q102,308
10
Q106
CN301
1
CN304
1
11
4
4
J301
i
Q101
R-CH
STANDBY
• SIGNAL PATH
: FM
: CD PLAY
: MD PLAY
: MD REC (ANALOG)
CN306
7
SP101
L-CH
SPEAKER
1
(Page 48)
3
AD LCH
7
5
26
CS
MD
SECTION
ELECTRONIC VOLUME
IC302
5
CD LCH
DAT
CLK
CD
SECTION
R-CH : Same as L-CH.
JACK BOARD (2/2)
MAIN BOARD (3/3)
SP201
R-CH
SPEAKER
4
13 14 15
CN408
8
RA LCH
AMP
Q105
SYSTWM CONTROLLER
IC401(3/3)
Q104
TUNER
SECTION
MUTE
DRIVE
Q301,304,306
A
(Page 45)
TU CLK
TU COUNT
11
12
13
14
TU CE
TU DATA
TU CLK
TU COUNT
CN303
1
5
6
4
POWER
CONTROL
Q430-432
FL BOARD
CN405 CN601
VDD
1
10
FLAC3.5V1
3
8
FLAC3.5V2
4
7
VFL
5
6
VDD
AC3.5V
VFL(-34V)
2
FL AC POWER
CONTROL
Q419-422
98
34
33
FL DRIVER
IC601
FL DATA 46
FL CTK 47
FL CS 45
FL RST 44
JACK BOARD (1/2)
R-CH
AU DATA
AU CLK
AU CS
MEGA BASS
A MUTE
PA STANDBY
FL CTR
CN301
BU 3.3V
MUTE
DRIVE
Q305
10 TU MUTE
1
2
3
4
TU CE
TU DATA
STANDBY
CONTROL
Q310
COM7V
6
5
7
8
10
4
3
1
4
63
62
61
60
4-39
DA
42-54
CP
CS
COM1 43
RESET
COM2 43
FL401
FL DRIVER
Q612,613
Q111
CN305
MUTE DRIVE
Q312,313
J302
LINE IN
35 LINE MUTE
LED BOARD (1/2)
CN602
3
IR RECEIVER
IC602
S601-605
CN406
11
CN406
LINE LEVEL
CONTROL
Q307,309,311
1
13
CN410
RESET
IC403
1
S402
(CD DOOR)
1
2
S633-638,640-646
26
23
25
24
29
22
27
97
31
15 CD DOOR
62 KEY AD0
61 KEY AD1
39 TU SFT
X401
8KHz
FREQUENCY
SHIFT
Q401
KEY BOARD
CN603
6-10
6-10
1-5
REG
Q405
COM 7V
UNREG 10V
REG
Q403
AC
CHECK
Q408
ACCHK 95
LED 5V
17-21 KEY S0-S4
51 KEY C0-C4
55-58
AU 3.3V
REG
IC411
10
5
6
7
8
9
9
8
7
6
5
10
12
4
2
LED DRIVE
Q603,604,
606-611
UNREG 14V
COM 7V
POWER
CONTROL
Q407,416
REG
Q402
BU 3.3V
REG
IC404
REG
IC402
CN901
3
T901
2
J901
AC IN
POWER
CONTROL
Q411.412
TX 87
STBY CTR 94
43 EXTAL
4
POWER BOARD (2/2)
TEX 86
X402
32kHz
CN602
CN401
42 XTAL
CN407
1-5
POWER
CONTROL
Q409
RA 7V
CD 6V
CN309
1
2
TOP BOARD
S608-631
LED 0
LED 123
LED 789
85 RMC
LED 456
LED CLOCK
LED CHARA-KANA
LED CHARA-ABC
60 KEY AD2
PC ON
RA POWER
40 RST
3 LINE LEVEL
2
CN641
LED BOARD (2/2)
REG
Q406
LED HISPEED 30
Q103
2
3
CN402
ACCHK
8
CN902
3
FL-34V
6
5
FLAC3.5V1
4
7
FLAC3.5V2
2
9
STBY CTR
10
1
BATT
7
4
RY901
RELAY
DRIVE
Q901
BATT
BOARD
CN903
1
CN904
1
2
2
DC 4.5V
04
– 51 –
– 52 –
ZS-M35
6-7. SCHEMATIC DIAGRAM — CD SECTION (1/2) — • Refer to page 95 for IC Block Diagrams.
(Page 55)
Common Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
: carbon pattern.
•
x
: parts mounted on the conductor side.
a
•
: Through hole.
• b : Pattern from the side which enables seeing.
Common Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• C : panel designation.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
• A : B+ Line.
• B : B– Line.
• H : adjustment for repair.
– 53 –
• Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
: Impossible to measure
∗
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
f : AM
E : MD PB
q : MD REC (DIGITAL)
j : MD REC (ANALOG)
J : CD
– 54 –
ZS-M35
6-8. SCHEMATIC DIAGRAM — CD SECTION (2/2) — • Refer to page 96 for IC Block Diagrams.
• Refer to page 54 for Note.
TP(RFO)
(Page 79)
TP(TEO)
(Page 82)
TP(VC)
(Page 72)
(Page 82)
(Page 53)
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : CD STOP
• Waveforms (CD BOARD)
1
2
3
4
Approx.
180mVp-p
1.0 – 1.4Vp-p
Approx.
120mVp-p
500mV/div, 500ns/div
50mV/div, 1µs/div
50mV/div, 1µs/div
IC701 ea (RFO) (CD PLAY)
IC701 ra (TEO) (CD PLAY)
IC701 rk (EFO) (CD PLAY)
– 55 –
5
1V/div, 10µs/div
IC702 el (LRCK) (CD PLAY)
4.3Vp-p
240ns
470ns
IC702 rd (BCK) (CD PLAY)
7
2V/div, 100ns/div
4.3Vp-p
4.1Vp-p
22.7µs
6
1V/div, 200ns/div
IC702 rk (XPCK) (CD PLAY)
– 56 –
2Vp-p
0.5V/div, 10ns/div
IC702 u; (XTAI) 33.9MHz
ZS-M35
6-9. PRINTED WIRING BOARDS — CD SECTION — • Refer to page 53 for Note.
1
2
3
4
5
6
7
8
9
10
11
12
13
A
(Page 76)
(Page 76)
(Page 73)
(Page 76)
B
CD MOTOR BOARD
C
D
E
M
M802
(SLED)
S801
(LIMIT)
F
TP(VC)
TP(TEO)
M
M801
(SPINDLE)
TP(RFO)
G
22
21
1-675-844-
(22)
H
(21)
• Semiconductor Location
– 57 –
Ref. No.
IC701
IC702
IC703
IC704
IC801
IC802
Location
F-8
E-3
C-8
C-5
C-12
G-12
Q701
G-7
– 58 –
Ref. No.
Q705
Q801
Q802
Q803
Q804
Q805
Q806
Q807
Location
F-6
E-12
E-12
F-11
F-12
G-12
D-11
E-11
ZS-M35
6-10. PRINTED WIRING BOARDS — TUNER SECTION — • Refer to page 53 for Note.
1
2
3
4
5
6
7
A
• Semiconductor
Location
B
C
Ref. No.
D1
D2
D3
D4
D5
D6
D7
D10
D11
Location
F-2
F-2
I-3
B-3
B-3
B-2
B-3
C-6
C-6
IC1
IC2
E-3
G-5
D
E
F
(Page 75)
G
H
TP(VT)
I
J
– 59 –
– 60 –
ZS-M35
6-11. SCHEMATIC DIAGRAMS — TUNER SECTION — • Refer to page 95 for IC Block Diagrams.
• Refer to page 54 for Note.
(Page 82)
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
(
) : AM
– 61 –
– 62 –
ZS-M35
6-12. PRINTED WIRING BOARDS — BD SECTION — • Refer to page 53 for Note.
1
2
3
4
5
6
7
8
9
10
11
12
13
A
B
C
D
E
F
G
04
15
DG BOARD
CN601
(Page 73)
H
17
(REC POSITION)
(LOADING)
16
DG BOARD
CN602
(Page 73)
DG BOARD
CN605
(Page 73)
• Semiconductor Location
I
(PACK OUT)
J
PLAY
21
(21)
1-671-115-
– 63 –
– 64 –
Ref. No.
D101
D181
D183
Location
A-1
G-6
G-6
IC101
IC103
IC121
IC123
IC124
IC152
IC171
B-12
D-2
E-12
F-4
E-13
C-9
G-1
Ref. No.
IC181
IC192
Location
F-10
F-9
Q101
Q102
Q103
Q104
Q162
Q163
Q181
Q182
C-13
C-2
E-1
D-2
C-13
D-13
F-10
F-11
ZS-M35
6-13. SCHEMATIC DIAGRAM — BD SECTION (1/2) — • Refer to page 98 for IC Block Diagrams. • Refer to page 54 for Note.
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : MD STOP
(
) : MD PLAY
<
> : MD REC
(Page 68)
– 65 –
– 66 –
ZS-M35
6-14. SCHEMATIC DIAGRAMS — BD SECTION (2/2) — • Refer to page 98 for IC Block Diagrams.
• Refer to page 54 for Note.
(Page 66)
• Waveforms (BD BOARD)
1
570mVp-p
200mV/div, 500ns/div
IC101 1, 2 (I, J) (MD PLAY)
2
Approx.
450mVp-p
200mV/div, 500ns/div
IC101 4 (A) (MD PLAY)
3
Approx.
440mVp-p
(Page 69)
200mV/div, 500ns/div
IC101 8, 9 (E, F) (MD PLAY)
4
3.4Vp-p
1V/div, 10ns/div
IC121 qh (OSCI) 45.5MHz
5
1V/div, 10µs/div
4.3Vp-p
22.7µs
IC121 wj (LRCK) (MD PLAY)
6
1V/div, 100ns/div
4.6Vp-p
(Page 69)
354ns
IC121 wk (XBCK) (MD PLAY)
7
1V/div, 50ns/div
4.8Vp-p
354ns
IC121 wl (FS256) (MD PLAY)
8
1V/div, 2µs/div
4.4Vp-p
5.7µs
IC121 o; (FS4) (MD PLAY)
(Page 69)
– 67 –
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : MD STOP
(
) : MD PLAY
<
> : MD REC
– 68 –
ZS-M35
6-15. SCHEMATIC DIAGRAM — DG SECTION (1/2) — • Refer to page 99 for IC Block Diagrams.
• Refer to page 54 for Note.
• Waveforms (DG BOARD)
1
2.0Vp-p
1V/div, 50ns/div
IC601 wk (XIN) 12MHz
2
1.9Vp-p
500mV/div, 10µs/div
IC601 wg (XIN-T) 32.8MHz
(Page
67)
3
3.4Vp-p
500mV/div, 10µs/div
IC603 qa (BCK)
(MD PLAY) 2.82MHz
4
1V/div, 10µs/div
3.7Vp-p
22.7µs
IC603 0 (LRCK) (MD PLAY)
5
4.2Vp-p
1V/div, 20ns/div
IC603 9 (SYSCK) 22.6MHz
6
0.8Vp-p
(Page
67)
200mV/div, 10ns/div
IC605 6 44.6MHz
(Page 71)
(Page
67)
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : MD PLAY
(
) : MD STOP
– 69 –
– 70 –
ZS-M35
6-16. SCHEMATIC DIAGRAM — DG SECTION (2/2) — • Refer to page 100 for IC Block Diagrams.
• Refer to page 54 for Note.
(Page 70)
(Page 79)
(Page 56)
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : MD PLAY
(
) : MD STOP
– 71 –
– 72 –
ZS-M35
6-17. PRINTED WIRING BOARD — DG SECTION — • Refer to page 53 for Note.
2
1
3
4
5
6
7
8
9
10
11
12
(Page 76)
MAIN BOARD
CN404
A
14
DG BOARD
SIDE A
DG BOARD
• Semiconductor
Location
SIDE B
B
C
D
E
BD BOARD
CN102
15
(Page 64)
F
G
H
BD BOARD
CN103
16
(Page 64)
I
1-677-061-
04
J
12
17
CD BOARD
CN705
SW BOARD
CN601
(Page 57)
(Page 63)
– 73 –
11
11
(11)
(11)
1-677-061-
– 74 –
Ref. No.
D602
D603
Location
G-6
F-8
IC601
IC602
IC603
IC604
IC605
IC606
H-9
I-8
F-9
F-11
F-10
G-11
Q603
Q604
Q610
Q611
Q612
Q616
Q617
Q620
G-8
H-6
E-4
I-8
D-4
E-9
E-8
F-8
ZS-M35
6-18. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 53 for Note.
2
1
3
4
5
6
7
8
CD BOARD (Page 57)
CN704
A
B
11
9
10
11
12
13
CD BOARD (Page 57)
CN707
13
MAIN BOARD
JACK BOARD
CN304
6
(Page 84)
MD SHIELD BOX
2
(Page 91)
C
3
D
1
(Page 60)
10
F
G
POWER BOARD
CN902
(Page 91)
TUNER BOARD
CN1
E
POWER BOARD
CN901
JACK BOARD
CN305
CD BOARD
CN702
(Page 57)
7
(Page 84)
KEY BOARD
CN603
8
(Page 84)
H
I
LED BOARD
CN602
14
4
(Page 73)
(Page 87)
TOP BOARD
CN641
(Page 87)
S402
CD DOOR
DG BOARD
CN604
9
JC109
BLK
JC113
BLK/GRY
JC106
JC105
5
J
FL BOARD
CN601
(Page 84)
1-675-212-
04
– 75 –
– 76 –
13
ZS-M35
6-19. SCHEMATIC DIAMGRAM — MAIN SECTION (1/3) — • Refer to page 100 for IC Block Diagrams.
• Refer to page 54 for Note.
(Page 85)
(Page 82)
(Page 79)
(Page 82)
(Page 80)
(Page 85)
(Page 82)
(Page 80)
• Semiconductor Location
Ref. No.
D301
D303
D304
D401
D402
D403
D404
D405
D406
IC301
Location
D-5
D-4
D-4
D-9
D-9
B-7
C-8
J-10
J-11
B-6
Ref. No.
IC302
IC303
IC305
IC401
IC402
IC403
IC404
IC411
Location
F-5
G-5
D-4
G-8
F-9
F-9
B-8
F-12
Q101
Q102
B-5
D-3
Ref. No.
Q103
Q104
Q105
Q106
Q111
Q201
Q202
Q203
Q204
Q205
Q206
– 77 –
Location
F-3
C-3
F-4
C-5
G-3
B-5
D-5
F-3
D-3
F-4
C-5
Ref. No.
Q211
Q301
Q304
Q305
Q306
Q307
Q308
Q309
Q310
Q311
Q312
Location
G-3
D-3
D-3
C-6
D-3
E-3
D-4
E-3
D-7
E-3
F-3
Ref. No.
Q313
Q401
Q402
Q403
Q405
Q406
Q407
Q408
Q409
Q411
Q412
Location
D-3
H-8
B-9
B-8
C-8
I-11
B-9
E-9
H-5
C-7
C-8
Ref. No.
Q415
Q416
Q419
Q420
Q421
Q422
Location
I-9
B-9
I-12
I-11
I-10
J-9
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
– 78 –
ZS-M35
6-20. SCHEMATIC DIAMGRAM — MAIN SECTION (2/3) — • Refer to page 100 for IC Block Diagrams.
• Refer to page 54 for Note.
(Page 81)
(Page 90)
(Page 86)
(Page 77)
(Page 89)
(Page 72)
(Page 85)
(Page 77)
(Page 56)
(Page 81)
(Page 77)
– 79 –
– 80 –
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
(
) : MD STOP
<
> : CD STOP
ZS-M35
(Page 80)
6-21. SCHEMATIC DIAMGRAM — MAIN SECTION (3/3) — • Refer to page 54 for Note.
(Page 62)
(Page 77)
(Page 56)
(Page 56)
(Page 77)
(Page 93)
(Page 80)
(Page 93)
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
– 81 –
– 82 –
ZS-M35
6-22. PRINTED WIRING BOARDS — PANEL SECTION — • Refer to page 53 for Note.
1
2
3
4
5
6
7
8
9
10
A
11
12
13
14
(Page 75)
FL401
FLUORESCENT INDICATOR TUBE
B
(Page 75)
C
21
(21)
(Page 76)
D
21
(21)
E
(Page 75)
F
G
• Semiconductor
Location
HIGH SPEED
H
AM/PM
11
(11)
SYMBOL
I
– 83 –
– 84 –
Ref. No.
D301
D302
D303
D304
Location
B-12
B-12
C-11
B-11
IC601
C-5
Q612
Q613
C-3
C-3
ZS-M35
6-23. SCHEMATIC DIAMGRAMS — PANEL SECTION — • Refer to page 99 for IC Block Diagrams.
• Refer to page 54 for Note.
(Page 77)
(Page 77)
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
(Page 80)
– 85 –
– 86 –
(Page 79)
ZS-M35
6-24. PRINTED WIRING BOARDS — SWITCH SECTION — • Refer to page 53 for Note.
2
1
3
4
5
6
7
8
9
10
11
12
13
14
A
B
13
C
(13)
(Page 75)
D
POWER
E
(Page 75)
F
abc
G
H
HIGH SPEED
• Semiconductor Location
I
21
AM/PM
SYMBOL
– 87 –
Ref. No.
D601
D602
D603
D604
D605
D606
D607
D608
D609
Location
H-13
H-11
H-10
H-9
H-8
H-7
H-5
G-6
G-7
Ref. No.
D610
D611
D612
D613
D614
D615
D616
D617
D618
Location
G-6
G-4
G-3
G-2
H-6
H-4
H-3
H-2
H-5
Ref. No.
D619
D620
D621
D622
D623
D624
D625
Location
H-4
H-3
H-2
I-5
I-4
I-3
I-2
IC602
I-13
Ref. No.
Q603
Q604
Q606
Q607
Q608
Q609
Q610
Q611
Location
G-13
G-12
H-5
G-7
H-3
H-4
H-5
I-5
– 88 –
(21)
ZS-M35
6-25. SCHEMATIC DIAGRAMS — SWITCH SECTION — • Refer to page 54 for Note.
(Page 79)
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
(Page 80)
– 89 –
– 90 –
ZS-M35
6-26. PRINTED WIRING BOARDS — POWER SUPPLY SECTION — • Refer to page 53 for Note.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
J901
AC IN
• Semiconductor Location
POWER BOARD
Ref. No.
D901
D902
D903
D904
D905
D906
D907
D908
D909
B
C
Location
H-6
H-7
H-6
H-7
H-5
H-6
H-5
H-5
H-3
Ref. No.
D910
D911
D912
D913
D914
D915
Location
I-4
I-3
H-4
H-5
F-7
H-5
Q901
Q902
I-6
I-4
T901
POWER TRANSFORMER
D
6
7
5
8
E
9
4
DRY BATTERY
UM3X3
4.5V
MEMORY
BACK-UP
BATT (+) BOARD
10
11
F
BATT (–) BOARD
2
12
13
1
14
G
15
H
21
21
1-675-221-
(21)
BLK
: NOT REPLACEABLE :
BUILT IN TRANSFORMER
I
BLK/WHT
1-675-220-
1
2
CN904
21
1-675-216-
04
3
2
MAIN BOARD
CN402
MAIN BOARD
CN401
(Page 76)
(Page 76)
– 91 –
(21)
– 92 –
(21)
ZS-M35
6-27. SCHEMATIC DIAGRAMS — POWER SUPPLY SECTION — • Refer to page 54 for Note.
(Page 82)
(Page 82)
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
– 93 –
– 94 –
6-28. IC BLOCK DIAGRAMS
AM
MIX
FM
OSC
LEVEL
DET
20 AM OSC
1/1 OR
1/16
19 OSC-OUT
ST
IF BUFF
IFB5
E IV AMP
IC802 BA6892FP-E2
C. OUT
21
XRST
20
DATA
OUT4+
OUT4–
OUT3+
DRIVER
CH4
CB
CC1
CC2
FOK
CC1
XDFCT1
DFCT2
TGFL
LPC
LPCL
IIL DATA REGISTER
INPUT SHIFT REGISTER
ADDRESS DECODER
SENS SELECTOR
OUTPUT DECODER
19
XLT
18
CLK
VCC
17
VCC
16
ISET
15
SL_O
14
SL_M
13
SL_P
DFCT
TZC COMP.
TM1
DFCTO IFB1-6 FS1-4
BAL1-4
TOG1-4
TRACKING
PHASE COMPENSATION
TG1
TG1-2 TM1-7 PS1-4
ISET
VCC
VC 46
TM4
VEE
VCC
TM6
FZC 47
FZC COMP.
DRIVER
CH2
CH2
MUTING
DRIVER
CH1
VCC
FOCUS
PHASE COMPENSATION
PVCC
4
5
6
7
8
9 10 11 12
13 14
IN2
MUTE2
TEST
PREGND
PWGND
PWGND
VCCPOW
OUT1–
OUT1+
3
OUT2+
1 2
TM5
TM3
TM7
FEO 48
15 VDD
MUTE1
POWER ON
RESET
FOH
FOL
TGH
TGL
BALH
BALL
ATSC
TZC
FZC
TTL
↓
IIL
TZC 44
16 15
THERMAL
SHUTDOWN
CH1
MUTING
UNLOCK
DETECTOR
LDON
E-F BALANCE
WINDOW COMP.
VCC
+
–
16 VSS
14 B04
VEE
VEE
FS1
FS2
DFCT
FSET
TG2
FS4
7
8
9
10
11
12
FSET
TA_M
TA_O
FE_O
6
TG2
5
TGU
4
SRCH
3
FE_M
2
FLB
12 AMIN
1
FGD
13 FMIN
FOFCT
VEE
1/2
FEI
UNIVERSAL
COUNTER
22
IIL
↓
TTL
MIRR
FOK
VCC
DRIVER
CH3
–
+
+
–
VCC
TRK. GAIN
WINDOW
COMP.
PVCC
CH4
MUTING
19 AOUT
18 AIN
17 PD
VEE
FO. BIAS
WINDOW
COMP.
TDFCT 45
CH3
MUTING
–
+
OUT3–
23 22 21 20 19 18 17
OUT2–
PHASE
DETECTOR
CHARGE
PUMP
VCCPOW
NC
24
PWGND
MUTE3
25
PWGND
IN3
26
PRGND
MUTE4
28 27
VCC
SWALLOW
COUNTER
1/16,1/17
4BITS
SENS1
INT
MIRR
VEE
ATSC
WINDOW
COMP.
BIAS
IN1
I02 10
DATA SHIFT REGISTER
LATCH
9
VEE
ATSC 43
VCCPRE
IN4
22 NC
CCB
I/F
REFERENCE
DIVIDER
I01
23
VEE
LEVEL S
TGFL
13 LPF1/BAND
BAL1
DECODE
VEE
VEE 40
20 XIN
8
CP
IFB6
E 39
21 XOUT
B03
RF_I
FE AMP
BAL2
BAL3
BAL4
14 LPF2/MO-ST
IC2 LC72137M-TLM
12BITS
PROGRAMMABLE
DIVIDER
SENS2
VCC
LPFI 42
7
RF_O
RFTC
VCC
17 IF-OUT
VCO
DIVIDE
IIL
↓
TTL
VCC
F 38
15 MPX- IN
6
24
VEE
TEO 41
B02
RF_H
LD
APC
PD2 IV
AMP
AF
MUTE
B01
25
VEE RF
VEE
SUMMING
AMP
VCC
PD2 37
16 DET-OUT
L-OUT 12
1
2
3
4
5
26
ST/MO
FM/AM
R-OUT 11
NC
CE
DI
CL
DO
27
VEE
18 ST-IND
IF REQ
FM
DET
QUAD 10
28
VCC
PD1 IV
AMP
SW
AF BUFF
29
VCC
F IV AMP
AGC
30
LASER POWER CONTROL
1/8
AM
DET
31
VEE
IFB4
FM IF
AM
OSC
32
VCC
IFB3
AM IF
FM IF-IN 7
AGC 9
33
IFB1
VCC2 5
GND2 8
34
21 FM OSC
BUFF BUFF
AF IF-IN 6
35
IFB2
FM
MIX
MIX OUT 4
36
23 VCC1
22 AM RF-IN
FM RF-IN 2
AM LOW CUT 3
PD
24 FM RF-OUT
FM RF
TOG1
TOG2
TOG3
TOG4
GND1 1
IC701 CXA2542AQ
PD1
IC1 TA2149N
IFIN 11
– 95 –
– 96 –
TM2
DOUT
C4M
XTSL
C2PO
GFS
XPCK
XUGF
VDD2
53
52
51
50
49
48
47
46 45 44
EFM
DEMODULATOR
VDD3
BCK
PCMD
EMPH
56 55 54
PCMDI
WFCK
59 58 57
BCKI
EXCK
SBSO
SCOR
60
VSS2
VSS3
EMPHI
IC702 CXD3009Q
43 42 41
DIGITAL
CUT
SERIAL-IN
INTERFACE
61
SYSM 62
AVSS 63
AVDD 64
AOUT1 65
40 LRCKI
DD/ /AA
INTERFACE
INTERFACE
ERROR
CORRECTOR
39 LRCK
ASYMMETRY
CORRECTOR
16K RAM
PWM
AIN1 66
38
37
36
35
ASYO
ASYI
BIAS
RF
34 AVDD
LOUT1 67
AVSS 68
XVDD 69
XTAI 70
XTAO 71
TIMING
LOGIC
3RD-ORDER
NOISE
SHAPER
XVSS 72
33
32
31
30
29
DIGITAL
PLL
OVER SAMPLING
DIGITAL FILTER
AVSS 73
OSC
28 VCTL
27 V16M
CLOCK
GENERATOR
26 VCKI
25 VPCO
LOUT2 74
PWM
AIN2 75
AOUT2 76
CLTV
AVSS
FILI
FILO
PCO
AVDD 77
24 TEST1
23 TEST0
AVSS 78
XRST 79
DIGITAL
CLV
VDD0 80
CPU
INTERFACE
VCC
IN3'
IN3
OUT3-A
24
23
22
21
20
19
18
VCC
OPIN-B
VCC
25
NC
VREFIN
26
DRIVE
BUFFER
OUT3-B
IN4'
27
IN4
OUT4-B
28
OUT4-A
GND
IC703 BA6998FP
17
16
15
DRIVE
BUFFER
VCC
LEVEL
SHIFT
LEVEL
SHIFT
–
+
+
–
REGULATOR VOLTAGE DETECT,
BIAS VOLTAGE DETECT,
THERMAL SHUT DOWN
LEVEL
SHIFT
DRIVER
MUTING
+
–
+
–
–
+
LEVEL
SHIFT
–
+
DRIVE
BUFFER
1
2
3 4 5
6
7
8
9 10
11
12
13 14
OUT1-B
OUT1-A
IN1
RESET
REG-B
REGOUT
MUTE
GND
IN2'
IN2
OUT2-A
OUT2-B
GND
OPOUT
DRIVE
BUFFER
– 97 –
15 16 17
18
19
20
FOK
VDD1
VSS1
XLON
XLTO
CLKO
DATO
SEIN
CNIN
10 11 12 13 14
SPOA
SPOB
7 8 9
DATA
XLAT
CLOCK
VSS0
4 5 6
SQCK
SQSO
SENS
2 3
LMUT
RMUT
1
SERVO AUTO
SEQUENCER
22 PWM1
21 MDP
CAPA–
CAPA+
IN2R
IN2F
VM2
OUT2F
PGND2
OUT2R
VM12
OUT1R
PGND1
OUT1F
VM1
IN1F
IN1R
VDD
IC152 BH6511FS
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
AMP
AMP
PREDRIVE
12
13
14
15
16
GND 3
PSB
11
PSB
IN3R
VM4
10
INTERFACE
–
+
RF AGC
RF
PEAK
44
43 42
41
40
39
38
37
USROP
RF AGC
+
–
EQ
USRC
EQ
DET
+
–
RFA1
AGCI
OPN
45
COMPO
RFO
46
COMPP
MORFI
47
ADDC
MORFO
IC101 CXA2523AR
48
BPF3T
RFA2
I
J
1
–1
–
–2
–
2
RFA3
HLPT
–1
CVB
IVR
WBL
TEMP
PEAK
–2
BOTTOM
PBSW
GRVA
WBL
35 ABCD
34 FE
–
–
–
–
AA
36 BOTM
PBH
–1
GRV
+
–
4
3T
PTGR
–
1
–
–2
–
+
A
3
P-P
–2
OFST
VC
AUX
SW
PEAK3T
3T
33 AUX
BPFC
ABCDA
32 ADFG
B
+
–
5
IVR
C
31 ADAGC
BB
+
–
6
IVR
+
+
–
–
30 ADIN
FEA
CC
DET
BPF22
D
–
–
+
+
+
–
7
IVR
ADIP
AGC
WBL
ATA
E
+
–
8
IVR
29 ADFM
DD
WBL
+
–
EE
EE'
–1
PTGR
–
+
–
+
–2
–2
ESW
+
–
9
IVR
FF
IV
+
–
3T
AUXSW
25 WBLADJ
VI CONV
BGR
COMMAND
–
+ –
VREF
SCRI - PARA
DECODE
APC 11
17
18
19
20
21
22 23
24
SCLK
XLAT
XSTBY
F0CNT
VREF
EQADJ
VCC
– 98 –
3TADJ
16
SWDT
TEMPI
15
TEMPR
14
GND
APCREF 12
13
26 TE
TEA
EQ
PD 10
+
TG
WBL
FF'
FBAL
GSW
28 SE
SEA
–1
TESW
EBAL
F
TG
27 CSLED
EFB
5
N.C
4
OUT
REFERENCE
VOLTAGE
VCC 2
IN3F
IN4F
9
VM3
IN4R
8
AMP
OUT3F
VG
7
OUT3R
GND
6
VM34
5
OUT4R
4
PGND4
3
AMP
PGND3
AMP
OUT4F
2
CTL 1
PREDRIVE
AMP
1
IC192 BA033FP-E2
PREDRIVE
PREDRIVE
INTERFACE
VDD
INTERFACE
OPO
CHARGE
PUMP.
OSC
AMP
AMP
INTERFACE
MNT1 2
DCHG
APC
ADFG
F0CNT
XLRF
CKRF
DTRF
APCREF
LDDR
TRDR
TFDR
DVDD
PWM
GENERATOR
EACH
BLOCK
MONITOR
CONTROL
MNT2 3
FFDR
92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76
SPINDLE
SERVO
MNT0 1
FRDR
FS4
SRDR
SFDR
SPRD
94 93
AUTO
SEQUENCER
100 99 98 97 96 95
SPFD
FGIN
TEST1
TEST2
TEST3
DVSS
EFMO
IC121 CXD2654R
75 TE
74 SE
73 AVSS
MNT3 4
72 ADRB
ADIP
DECODER
71 ADRT
70 AVDD
SWDT 5
69 ADIO
SCLK 6
EACH
BLOCK
CPU I/F
XLAT 7
SRDT 8
68 VC
SERVO
DSP
SENS 9
A/D
CONVERTER
67 AUX1
66 FE
ANALOG
MUX
65 ABCD
XRST 10
64 BOTM
SQSY 11
63 PEAK
SUBCODE
PROCESSOR
DQSY 12
62 CLTV
EFM/ACIRC
ENCODER/
DECODER
PLL
RECP 13
SHOCK RESISTANT
MEMORY CONTROLLER
XINT 14
61 FILO
60 FILI
59 PCO
TX 15
58 AVSS
OSCI 16
CLOCK
GENERATOR
OSCO 17
XTSL 18
EACH
BLOCK
DIGITAL
AUDIO
I/F
DIN0 19
DIN1 20
57 RFI
COMP
SAMPLING
RATE
CONVERTER
56 BIAS
55 AVDD
54 ASYI
DOUT 21
53 ASYO
DATAI 22
ATRAC
ENCODER/DECODER
LRCKI 23
XBCKI 24
52 MVCI
ADDT 25
ADDRESS/DATA BUS A00 - A11, D0 - D3
IC602 BA6287F
D2
D0
D1
XWE
XRAS
A09
XCAS
XOE
DVSS
A11
A08
A07
A06
A05
A04
A10
A01
A00
A02
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
A03
DVDD
FS256
LRCK
XBCK
DADT
26 27 28 29 30
51 D3
IC601 ML9206-03MBZ060 (FL BOARD)
OUT1 1
VM 2
DRIVER
P1 1
P2 2
PORT
DRIVER
7 OUT2 AD2 3
AD1 4
AD
DRIVE
DRIVER
VCC 3
CONTROL LOGIC
8BIT
SHIFT
REGISTER
CONTROL
CIRCUIT
WRITE
ADDRESS
COUNTER
TSD
READ
ADDRESS
COUNTER
ADDRESS
SELECTOR
ADRAM
16Wx2B
5 RIN
DCRAM
16Wx8B
CGROM
248Wx35B
SEG28 32
OSCILLATOR
57 GND
56 VFL
DIGIT
CONTROL
GRID
DRIVER
DUTY
CONTROL
59 OSC1
58 OSC0
55 COM16
40 COM1
CGRAM
8Wx35B
SEGMENT
DRIVE
SEG1 5
TIMING
GENERATOR1
VDD
DA
CP
CS
RESET
COMMAND
DECODER
TIMING
GENERATOR2
6 VREF
POWER
SAVE
FIN 4
64
63
62
61
60
8 GND
39 SEG35
33 SEG29
– 99 –
IC603 PCM3003E/T2
VCC1
VCC1
1
2
VINR
3
VREF1
4
VREF2
5
VINL
6
PDAD
7
PDDA
8
SYSCK
A/D CONVERTER
BLOCK
D/A CONVERTER
BLOCK
ANALOG
FRONT-END
CIRCUIT
ANALOG
FRONT-END
CIRCUIT
∆Σ
MODULATOR
∆Σ
MODULATOR
DECIMATION
& LOW CUT
FILTER
DECIMATION
& LOW CUT
FILTER
ANALOG
LOW-PASS
FILTER
ANALOG
LOW-PASS
FILTER
MULTI-LEVEL
∆Σ
MODULATOR
MULTI-LEVEL
∆Σ
MODULATOR
INTERPOLATION
FILTER
X8
OVERSAMPLING
INTERPOLATION
FILTER
X8
OVERSAMPLING
24
23
22
21
20
19
VCC2
AGND1
AGND2
VCOM
VOUTR
VOUTL
18
17
16
15
14
13
DEM0
DEM1
20BIT
DIN
VDD
DGND
REFERENCE
RESET &
POWER
DOWN
9
CLOCK
SERIAL INTERFACE
LRCIN 10
BCKIN 11
DOUT 12
MODE
CONTROL
INTERFACE
SIMIN2
SIMOUT2
BASS2
CH2IN2
CH2IN3
CH2IN4
TRF2
OUT2
AGND
DVDD
CS
28 27
26
25
24
23
22
21
20
19
18 17 16 15
AVDD
RECOUT2
IC411 XC62FP3302PR
CH2IN1
IC302 M62443FPD61Q
VOUT 1
VIN 2
VR3
SIMAMP2
VR5
VREF
VSS 3
TONE
AMP2
VR2
CONTROL
LOGIC
VOLAMP2
VOLAMP1
VR1
TONE
AMP1
REF
VR5
SIMAMP1
1 2
3
4
5
6
7
8
9
10
11 12 13 14
REF
CH1IN1
RECOUT1
SIMIN1
SIMOUT1
BASS1
CH1IN2
CH1IN3
CH1IN4
TER1
OUT1
DGND
DAT
CLK
VR3
– 100 –
SECTION 7
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
• Accessories and packing materials are
given in the last of this parts list.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
7-1. CABINET (REAR) SECTION
3
#3
ANT1
10
A
4
#1
#1
#2
#2
#3
2
B
#7 #1
#11
#2
T901
#11
F903
#2
#1
9
F901
8
#3
8
F902
#3
1
A
7
B
5
Remark
#3
6
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
* 1
* 2
3
3
3
A-3322-637-A
3-039-987-01
3-039-974-21
3-039-974-31
3-039-974-41
POWER BOARD, COMPLETE
CHASSIS, TRANSFORMER
HANDLE (BLUE)
HANDLE (ORANGE)
HANDLE (BLACK)
7
7
8
* 9
* 10
3-224-133-31
3-224-133-41
3-039-967-01
1-675-220-11
3-703-044-26
CABINET (REAR) (BLUE)
CABINET (REAR) (ORANGE)
TERMINAL (BATT –), BATTERY
BATT (+) BOARD
LABEL, CAUTION
4
4
4
* 5
6
3-039-976-21
3-039-976-31
3-039-976-51
1-675-221-11
3-039-958-01
LID, BATTERY CASE (BLUE)
LID, BATTERY CASE (ORANGE)
LID, BATTERY CASE (BLACK)
BATT (–) BOARD
TERMINAL, ANT
ANT1
0 F901
0 F902
0 F903
0 T901
1-501-452-11
1-576-099-11
1-576-105-11
1-576-107-11
1-435-320-11
ANTENNA, TELESCOPIC
FUSE (0.8A/250V)
FUSE (2.5A/250V)
FUSE (3.15A/250V)
TRANSFORMER, POWER
7
#2
3-039-971-51 CABINET (REAR) (BLACK)
– 101 –
Remark
7-2. CABINET (FRONT) SECTION
68
58
C
57
65
#3
SP101
70
65
56
65
70
#3
60
70
67
not supplied
66
61
#3
54
64
69
55
65
#3
62
#3
#3
65
C
not supplied
#3
59
#3
63
51(including
SP201
#3
)
52
53
Ref. No.
Part No.
Description
51
52
53
53
53
X-3378-657-1
3-040-916-01
X-3377-977-1
X-3378-003-1
X-3378-052-1
CABINET FRONT (SUB) ASSY
FOOT (F), RUBBER
CHASSIS ASSY, NET (BLACK)
CHASSIS ASSY, NET (BLUE)
CHASSIS ASSY, NET (ORANGE)
54
55
* 56
* 57
* 57
3-039-977-02
3-040-704-01
1-675-223-11
A-3062-399-A
A-3322-633-A
WINDOW (FL)
BUTTON (REC) (4P)
KEY BOARD
LED BOARD, COMPLETE (ORANGE)
LED BOARD, COMPLETE (GREEN)
* 58
59
60
1-675-213-11 TOP BOARD
3-039-954-01 PLATE (10 KEY), LIGHT GUIDE
1-791-523-11 WIRE, PARALLEL (FFC) (13 CORE)
Remark
Ref. No.
Part No.
Description
61
* 62
* 63
64
65
1-791-522-11
A-3322-634-A
1-675-219-11
3-039-979-01
4-951-620-01
WIRE, PARALLEL (FFC) (10 CORE)
TUNER BOARD, COMPLETE
JACK BOARD
BUTTON (10 KEY)
SCREW (2.6X8), +BVTP
66
67
68
69
70
3-041-800-01
3-041-801-01
X-3378-404-1
3-047-735-01
4-951-620-11
SHEET (A), ADHESIVE
SHEET (B), ADHESIVE
BUTTON (TOP) ASSY
CUSHION (REC), RUBBER
SCREW (2.6X10), +BVTP
SP101
SP201
1-529-463-11 SPEAKER (8cm)
1-529-463-11 SPEAKER (8cm)
– 102 –
Remark
7-3. CABINET (UPPER) SECTION
S402
106
109
108
not supplied
111
107
112
110
113
#3
#4
#3
#3
114
#3
115
105
KSM-213CDM
117
115
not
supplied
not
supplied
FL401
116
#3
117
117
104
#3
116
102
117 118
103
119
101
#3
#3
Ref. No.
Part No.
Description
Part No.
Description
* 101
102
103
* 104
105
A-3322-636-A
3-039-961-01
1-791-521-11
A-3322-656-A
3-039-978-01
MAIN BOARD, COMPLETE
SPRING (IC)
WIRE, PARALLEL (FFC) (10 CORE)
FL BOARD, COMPLETE
HOLDER (FL)
112
113
114
115
116
1-452-899-11
3-036-467-01
3-923-736-01
3-931-379-31
3-931-379-21
MAGNET
PLATE, CHUCKING
COVER, CD
RUBBER, VIBRATION PROOF
RUBBER, VIBRATION PROOF
106
* 107
108
109
110
1-791-520-11
A-3322-529-A
3-039-972-01
3-039-957-01
3-922-112-31
WIRE, PARALLEL (FFC) (18 CORE)
CD BOARD, COMPLETE
CABINET (UPPER)
SPRING (CD UP)
DAMPER
117
118
* 119
FL401
S402
3-921-725-01
1-791-518-11
A-3322-635-A
1-517-916-11
1-692-960-11
SCREW (2.6X10), +PWH
WIRE, PARALLEL (FFC) (16 CORE)
CD MOTOR BOARD, COMPLETE
INDICATOR TUBE, FLUORESCENT
SWITCH, PUSH (1 KEY) (CD DOOR)
111
Remark
#3
Ref. No.
3-039-975-01 LID, CD
– 103 –
Remark
7-4. MD BLOCK SECTION
MDM-5GA
153
153
151
152
#5
not supplied
not supplied
not supplied
#5
not supplied
154
158
155
#5
#5
156
157
#5
#5
159
#5
#5
#5
Ref. No.
151
152
153
154
155
Part No.
Description
3-036-318-11
3-036-311-01
3-042-390-01
1-791-519-11
1-791-531-21
CARTRIDGE, LID
SPRING (MD LID)
SCREW (+BVTTWH M3), STEP
WIRE, PARALLEL (FFC) (26 CORE)
WIRE, PARALLEL (FFC) (21 CORE)
Remark
Ref. No.
156
157
158
159
– 104 –
#5
Part No.
Description
1-791-532-21
A-3322-531-A
3-041-799-01
X-3378-454-1
WIRE, PARALLEL (FFC) (23 CORE)
DG BOARD, COMPLETE
SHEET, INSULATING
PLATE (LOWER) ASSY, SHIELD
Remark
7-5. MD MECHANISM SECTION
(MDM-5GA)
224
213
211
212
213
217
218
210
214
207
209
219
221
220
215
208
#6
222
216
223
203
225
207
203
202
#6
201
226
206
#4
204
M103
205
MBU-5A
#6
Ref. No.
Part No.
Description
* 201
* 202
203
* 204
205
1-671-115-21
4-996-217-01
4-996-223-11
4-996-218-01
4-996-277-01
SW BOARD
CHASSIS
INSULATOR (F)
BRACKET (GUIDE R)
SPRING (O/C), TENSION
206
207
* 208
209
210
4-996-226-01
4-999-347-01
4-996-225-01
4-988-466-11
4-996-219-01
LEVER (O/C)
INSULATOR (R)
BRACKET (GUIDE L)
SPRING (ELECTROSTATIC), LEAF
GEAR (CAM GEAR)
211
212
213
214
4-996-220-01
4-996-221-01
4-933-134-01
4-996-224-01
GEAR (A)
GEAR (B)
SCREW (+PTPWH M2.6X6)
SCREW (1.7X3), +PWH
Remark
Ref. No.
Part No.
Description
215
216
217
218
219
4-996-227-11
4-996-229-01
4-996-212-01
4-996-213-01
4-996-214-01
LEVER (HEAD)
SPRING (HEAD LEVER), TORSION
LEVER (LIMITER)
SPRING (LIMITER), TORSION
SPRING (SLIDER), TENSION
220
221
222
223
* 224
4-996-216-01
4-996-215-11
X-4949-668-3
X-4949-667-4
4-996-211-11
SPRING (HOLDER), TENSION
SPRING (LOCK LEVER), TENSION
SLIDER ASSY
HOLDER ASSY
SLIDER (CAM)
225
226
M103
– 105 –
4-998-763-03 SPRING (SHUTTER), LEAF
A-4680-200-G HOLDER COMPLETE ASSY
X-4949-264-1 MOTOR ASSY, LOADING (LOADING)
Remark
7-6. MD BASE UNIT SECTION
(MBU-5A)
252
#8
265
264
HR901
266
271
#9
263
267
#8
270
268
#8
not supplied
269
262
272
261
#8
#8
not supplied
256
#10
M101
255
259
#9
273
S102
260
#8
258
254
#8
257
252
253
M102
251
252
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No.
Part No.
Description
251
252
* 253
* 254
255
A-4699-893-A
3-372-761-01
4-996-267-01
4-996-255-01
4-900-590-01
BD BOARD, COMPLETE
SCREW (M1.7), TAPPING
BASE (BU-D)
BASE (BU-C)
SCREW, PRECISION SMALL
256
257
* 258
* 259
0 260
4-996-258-01
4-996-262-01
1-667-954-11
4-210-664-11
A-4672-541-A
SPRING, COMPRESSION
GEAR (SL-C)
FLEXIBLE BOARD
BASE (BU-A)
PICK-UP, OPTICAL KMS-260B
* 261
* 262
263
264
4-996-252-01
4-996-254-01
4-967-688-11
4-996-260-01
CHASSIS, BU
BASE (BU-B)
MAGNET, ABSORPTION
GEAR (SL-A)
Remark
Ref. No.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
Part No.
Description
265
266
267
268
269
4-996-261-01
4-996-264-01
4-996-265-01
4-996-256-11
4-996-257-01
GEAR (SL-B)
SPRING (SHAFT), LEAF
SHAFT, MAIN
SL (BASE)
RACK (SL)
270
271
272
273
4-996-263-01
4-988-560-01
4-211-036-01
A-4672-475-A
HR901
M102
S102
– 106 –
Remark
SPRING (CLV), TORSION
SCREW (+P 1.7X6)
SCREW (1.7X2.5), +PWH
MOTOR ASSY, SPINDLE (SPINDLE)
(INCLUDING M101)
1-500-502-11 HEAD, OVER WRITE
A-4672-474-A MOTOR ASSY, SLED (SLED)
1-762-148-21 SWITCH, PUSH (2 KEY) (REFLECT RATE
DETECT, PROTECT DETECT)
7-7. OPTICAL PICK-UP SECTION
(KSM-213CDM)
303
not supplied
306
302
305
301
304
M701
M702
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No.
Part No.
Description
301
302
0 303
304
2-626-908-01
3-713-786-51
8-848-483-05
X-2626-202-1
SHAFT, SLED
SCREW +P 2X3
PICK-UP, OPTICAL KSS-213C
CHASSIS ASSY, MOTOR (MB) (SPINDLE)
(INCLUDING M701)
Remark
Ref. No.
305
306
M702
– 107 –
Part No.
Description
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
Remark
2-627-003-02 GEAR (B) (RP)
2-626-907-01 GEAR (A)
X-2625-769-1 GEAR ASSY, MOTOR (MB) (RP) (SLED)
BATT (+)
BATT (–)
SECTION 8
ELECTRICAL PARTS LIST
BD
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
Ref. No.
Part No.
*
1-675-220-11 BATT (+) BOARD
**************
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
Description
Remark
1-675-221-11 BATT (–) BOARD
**************
3-039-967-01 TERMINAL (BATT –), BATTERY
*************************************************************
A-4699-893-A BD BOARD, COMPLETE
*******************
< CAPACITOR >
C101
C102
C103
C104
C105
1-125-822-11
1-163-038-00
1-125-822-11
1-125-822-11
1-163-021-11
TANTALUM
CERAMIC CHIP
TANTALUM
TANTALUM
CERAMIC CHIP
10uF
0.1uF
10uF
10uF
0.01uF
20%
C106
C107
C108
C109
C111
1-163-275-11
1-163-038-00
1-163-038-00
1-163-037-11
1-164-344-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.1uF
0.1uF
0.022uF
0.068uF
5%
10%
10%
50V
25V
25V
25V
25V
C112
C113
C115
C116
C117
1-163-017-00
1-109-982-11
1-164-489-11
1-163-037-11
1-163-809-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
1uF
0.22uF
0.022uF
0.047uF
5%
10%
10%
10%
10%
50V
10V
16V
25V
25V
C118
C119
C121
C122
C123
1-163-038-00
1-125-822-11
1-125-822-11
1-163-021-11
1-163-038-00
CERAMIC CHIP
TANTALUM
TANTALUM
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
10uF
0.01uF
0.1uF
20%
20%
10%
25V
10V
10V
50V
25V
C124
C127
C128
C129
C130
1-163-038-00
1-163-038-00
1-163-021-11
1-107-823-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.01uF
0.47uF
100PF
10%
10%
5%
25V
25V
50V
16V
50V
C131
C132
C133
C134
C135
1-163-023-00
1-107-823-11
1-163-017-00
1-163-038-00
1-163-038-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.015uF 5%
0.47uF
10%
0.0047uF 5%
0.1uF
0.1uF
50V
16V
50V
25V
25V
20%
20%
10%
10V
25V
10V
10V
50V
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.
3-039-967-01 TERMINAL (BATT –), BATTERY
*************************************************************
*
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Ref. No.
Part No.
Description
Remark
C136
C142
C143
C144
C146
1-126-206-11
1-163-251-11
1-163-251-11
1-163-251-11
1-163-038-00
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
100PF
100PF
100PF
0.1uF
20%
5%
5%
5%
6.3V
50V
50V
50V
25V
C151
C152
C153
C156
C158
1-126-206-11
1-163-038-00
1-163-021-11
1-163-038-00
1-163-019-00
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
20%
0.1uF
0.01uF
10%
0.1uF
0.0068uF 10%
6.3V
25V
50V
25V
50V
C160
C161
C163
C164
C167
1-104-601-11
1-104-601-11
1-163-021-11
1-163-021-11
1-163-038-00
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
10uF
0.01uF
0.01uF
0.1uF
10V
10V
50V
50V
25V
C168
C169
C171
C181
C183
1-163-038-00
1-125-822-11
1-163-038-00
1-104-913-11
1-163-038-00
CERAMIC CHIP
TANTALUM
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
0.1uF
10uF
0.1uF
10uF
0.1uF
C184
C185
C187
C188
C189
1-117-970-11
1-164-611-11
1-104-913-11
1-163-021-11
1-163-989-11
ELECT CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.001uF
10uF
0.01uF
0.033uF
20%
10%
20%
10%
10%
10V
500V
16V
50V
25V
C190
C191
C196
C197
1-126-206-11
1-163-038-00
1-163-038-00
1-163-038-00
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.1uF
0.1uF
0.1uF
20%
6.3V
25V
25V
25V
20%
20%
10%
10%
20%
20%
< CONNECTOR >
CN101
CN102
CN103
CN104
CN110
1-569-479-51
1-784-833-21
1-784-834-21
1-770-687-11
1-695-440-21
CONNECTOR, FPC 21P
CONNECTOR, FFC (LIF(NON-ZIF)) 21P
CONNECTOR, FFC (LIF(NON-ZIF)) 23P
CONNECTOR, FFC/FPC 4P
PIN, CONNECTOR (PC BOARD) 6P
< DIODE >
D101
D181
D183
8-719-988-61 DIODE 1SS355TE-17
8-719-046-86 DIODE F1J6TP
8-719-046-86 DIODE F1J6TP
< IC >
IC101
IC103
– 108 –
8-752-080-95 IC CXA2523AR
8-729-903-10 TRANSISTOR FMW1
25V
10V
25V
16V
25V
BD
Ref. No.
Part No.
Description
IC121
IC123
IC124
IC152
IC171
8-752-389-44
8-759-096-87
8-759-590-00
8-759-430-25
8-759-487-04
IC
IC
IC
IC
IC
Remark
IC181
IC192
8-759-481-17 IC MC74ACT08DTR2
8-759-460-72 IC BA033FP-E2
CXD2654R
TC7WU04FU(TE12R)
MN41V4400TT-08LT1
BH6511FS
S-24C02AFJA-TB-01
Ref. No.
Part No.
Description
R129
R130
R131
R132
R133
1-216-295-00
1-216-295-00
1-216-073-00
1-216-097-11
1-216-117-00
SHORT
SHORT
METAL CHIP
RES-CHIP
METAL CHIP
0
0
10K
100K
680K
Remark
R134
R135
R136
R137
R140
1-216-049-11
1-216-061-00
1-216-049-11
1-216-295-00
1-216-029-00
RES-CHIP
METAL CHIP
RES-CHIP
SHORT
METAL CHIP
R142
R143
R144
R145
R146
1-216-073-00
1-216-073-00
1-216-025-11
1-216-073-00
1-216-037-00
R147
R148
R149
R150
R151
5%
5%
5%
1/10W
1/10W
1/10W
1K
3.3K
1K
0
150
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
10K
10K
100
10K
330
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1-216-025-11
1-216-045-00
1-216-073-00
1-216-295-00
1-216-073-00
RES-CHIP
METAL CHIP
METAL CHIP
SHORT
METAL CHIP
100
680
10K
0
10K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
1-216-073-00
1-216-097-11
1-216-097-11
1-216-295-00
1-216-057-00
METAL CHIP
RES-CHIP
RES-CHIP
SHORT
METAL CHIP
10K
100K
100K
0
2.2K
5%
5%
5%
1/10W
1/10W
1/10W
< TRANSISTOR >
R152
R158
R159
R160
R161
5%
1/10W
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
R162
R163
R164
R165
R166
1-216-057-00
1-216-057-00
1-216-045-00
1-216-097-11
1-216-298-00
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
2.2K
2.2K
680
100K
2.2
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R167
R169
R170
R171
R173
1-216-065-11
1-219-724-11
1-216-073-00
1-216-073-00
1-216-121-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
4.7K
1
10K
10K
1M
5%
1%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
R175
R177
R179
R180
R182
1-216-065-11
1-216-061-00
1-216-085-00
1-216-073-00
1-216-089-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
4.7K
3.3K
33K
10K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R183
R184
R185
R186
R188
1-216-089-11
1-216-073-00
1-216-081-00
1-216-089-11
1-216-073-00
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
47K
10K
22K
47K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
SHORT
SHORT
10K
10K
10K
0
0
5%
5%
5%
1/10W
1/10W
1/10W
< COIL >
L101
L102
L103
L105
L106
1-414-813-11
1-414-813-11
1-414-813-11
1-414-813-11
1-414-813-11
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
L121
L122
L151
L152
L153
1-414-813-11
1-414-813-11
1-412-029-11
1-412-029-11
1-412-032-11
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
INDUCTOR CHIP 10uH
INDUCTOR CHIP 10uH
INDUCTOR CHIP 100uH
L154
L161
L162
L181
1-412-032-11
1-414-813-11
1-414-813-11
1-216-295-00
INDUCTOR CHIP 100uH
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
SHORT
0
Q101
Q102
Q103
Q104
Q162
8-729-403-35
8-729-026-53
8-729-402-93
8-729-402-93
8-729-101-07
UN5113
2SA1576A-T106-QR
UN5214-TX
UN5214-TX
2SB798-DL
Q163
Q181
Q182
8-729-403-35 TRANSISTOR UN5113
8-729-018-75 FET 2SJ278MY
8-729-017-65 FET 2SK1764KY
< RESISTOR >
R103
R104
R105
R106
R107
1-216-049-11
1-216-073-00
1-216-065-11
1-216-133-00
1-216-113-00
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
1K
10K
4.7K
3.3M
470K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R109
R110
R111
R112
R113
1-216-295-00
1-216-073-00
1-216-295-00
1-216-089-11
1-216-049-11
SHORT
METAL CHIP
SHORT
RES-CHIP
RES-CHIP
0
10K
0
47K
1K
5%
1/10W
5%
5%
1/10W
1/10W
R115
R117
R120
R121
R123
1-216-049-11
1-216-113-00
1-216-025-11
1-216-097-11
1-216-295-00
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
SHORT
1K
470K
100
100K
0
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R189
R190
R195
R196
R197
1-216-073-00
1-216-073-00
1-216-073-00
1-216-295-00
1-216-295-00
R124
R125
R127
1-216-025-11 RES-CHIP
1-216-025-11 RES-CHIP
1-216-025-11 RES-CHIP
100
100
100
5%
5%
5%
1/10W
1/10W
1/10W
R198
1-216-296-00 SHORT
– 109 –
0
BD
CD
Ref. No.
Part No.
Description
Remark
< SWITCH >
S101
S102
1-762-596-21 SWITCH, PUSH (1 KEY) (LIMIT IN)
1-762-148-21 SWITCH, PUSH (2 KEY) (REFLECT RATE
DETECT, PROTECT DETECT)
*************************************************************
A-3322-529-A CD BOARD, COMPLETE
*******************
*
< CAPACITOR >
Ref. No.
Part No.
Description
C746
C747
C748
C749
C750
1-163-001-11
1-164-489-11
1-163-809-11
1-163-021-11
1-163-021-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.22uF
0.047uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
50V
16V
25V
50V
50V
Remark
C752
C753
C754
C755
C756
1-163-021-11
1-163-021-11
1-163-021-11
1-163-251-11
1-163-263-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
100PF
330PF
10%
10%
10%
5%
5%
50V
50V
50V
50V
50V
C701
C702
C703
C704
C705
1-104-665-11
1-163-021-11
1-163-009-11
1-163-809-11
1-163-017-00
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.01uF
0.001uF
0.047uF
0.0047uF
20%
10%
10%
10%
5%
10V
50V
50V
25V
50V
C757
C758
C759
C760
C762
1-163-021-11
1-163-251-11
1-163-017-00
1-163-017-00
1-163-021-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
100PF
0.0047uF
0.0047uF
0.01uF
10%
5%
5%
5%
10%
50V
50V
50V
50V
50V
C706
C707
C708
C709
C710
1-163-021-11
1-126-925-11
1-107-725-11
1-163-019-00
1-107-725-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
470uF
0.1uF
0.0068uF
0.1uF
10%
20%
10%
10%
10%
50V
10V
16V
50V
16V
C763
C764
C765
C766
C767
1-163-259-11
1-163-021-11
1-163-021-11
1-104-665-11
1-163-229-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
220PF
0.01uF
0.01uF
100uF
12PF
5%
10%
10%
20%
5%
50V
50V
50V
10V
50V
C711
C712
C713
C714
C715
1-107-725-11
1-163-037-11
1-104-664-11
1-164-161-11
1-107-725-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.022uF
47uF
0.0022uF
0.1uF
10%
10%
20%
10%
10%
16V
25V
10V
100V
16V
C768
C769
C770
C773
C774
1-163-229-11
1-104-665-11
1-104-665-11
1-126-964-11
1-126-964-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
12PF
100uF
100uF
10uF
10uF
5%
20%
20%
20%
20%
50V
10V
10V
50V
50V
C716
C717
C718
C719
C720
1-126-964-11
1-107-725-11
1-107-725-11
1-163-227-11
1-115-566-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.1uF
0.1uF
10PF
4.7uF
20%
10%
10%
0.5PF
10%
50V
16V
16V
50V
10V
C775
C776
C777
C778
C780
1-163-021-11
1-115-566-11
1-104-665-11
1-163-021-11
1-163-239-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
4.7uF
100uF
0.01uF
33PF
10%
10%
20%
10%
5%
50V
10V
10V
50V
50V
C721
C722
C723
C724
C725
1-163-021-11
1-163-989-11
1-163-989-11
1-163-229-11
1-163-133-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.033uF
0.033uF
12PF
470PF
10%
10%
10%
5%
5%
50V
25V
25V
50V
50V
C781
C782
C783
C790
1-163-021-11
1-163-021-11
1-163-021-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
100PF
10%
10%
10%
5%
50V
50V
50V
50V
C726
C727
C728
C729
C730
1-163-021-11
1-107-725-11
1-163-227-11
1-163-059-11
1-125-838-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
10PF
0.01uF
2.2uF
10%
10%
0.5PF
10%
10%
50V
16V
50V
50V
6.3V
C731
C732
C733
C734
C735
1-164-344-11
1-163-989-11
1-163-243-11
1-163-009-11
1-163-021-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.068uF
0.033uF
47PF
0.001uF
0.01uF
10%
10%
5%
10%
10%
25V
25V
50V
50V
50V
C736
C737
C738
C739
C740
1-104-665-11
1-163-251-11
1-163-251-11
1-163-251-11
1-163-021-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
100PF
100PF
100PF
0.01uF
20%
5%
5%
5%
10%
10V
50V
50V
50V
50V
C743
C744
C745
1-163-021-11 CERAMIC CHIP
1-163-251-11 CERAMIC CHIP
1-163-011-11 CERAMIC CHIP
0.01uF
10%
100PF
5%
0.0015uF 10%
50V
50V
50V
< CONNECTOR >
CN701
* CN702
CN704
* CN705
* CN707
1-770-646-11
1-691-077-21
1-569-614-11
1-785-654-11
1-573-455-11
CONNECTOR, FFC/FPC 16P
HOUSING, CONNECTOR 18P
PLUG, CONNECTOR 2P
PIN, CONNECTOR (PC BOARD) 2P
PLUG, CONNECTOR 4P
< FERRITE BEAD >
FB701
FB702
FB703
FB704
FB713
1-216-295-00
1-216-295-00
1-469-180-22
1-469-180-22
1-216-295-00
SHORT
0
SHORT
0
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
SHORT
0
FB714
1-216-295-00 SHORT
< IC >
IC701
IC702
– 110 –
8-752-083-24 IC CXA2542AQ
8-752-387-78 IC CXD3009Q
0
CD
Ref. No.
IC703
IC704
Part No.
Description
Remark
Ref. No.
8-759-591-62 IC BA6998FP
8-759-652-44 IC BA033ST-V5
< JUMPER RESISTOR >
JC702
JC704
JC705
JC706
JC707
1-216-295-00
1-216-295-00
1-216-295-00
1-216-296-00
1-216-049-11
SHORT
SHORT
SHORT
SHORT
RES-CHIP
0
0
0
0
1K
JC708
JC709
JC711
JC713
JC715
1-216-295-00
1-216-295-00
1-216-296-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
JC720
JC721
JC723
JC725
JC730
1-216-295-00
1-216-295-00
1-216-049-11
1-216-295-00
1-216-295-00
SHORT
SHORT
RES-CHIP
SHORT
SHORT
0
0
1K
0
0
JC734
JC739
1-216-295-00 SHORT
1-216-295-00 SHORT
5%
5%
1/10W
1/10W
0
0
< COIL >
L701
L702
1-216-025-11 RES-CHIP
100
1-410-997-22 INDUCTOR CHIP 2.2uH
5%
1/10W
< TRANSISTOR >
Q701
Q705
8-729-101-07 TRANSISTOR 2SB798-DL
8-729-931-02 TRANSISTOR 2SC2413KQ
< RESISTOR >
R700
R701
R702
R703
R704
1-216-077-11
1-216-089-11
1-216-295-00
1-216-117-00
1-216-075-00
RES-CHIP
RES-CHIP
SHORT
METAL CHIP
METAL CHIP
15K
47K
0
680K
12K
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R705
R706
R707
R710
R711
1-216-214-00
1-216-101-00
1-216-033-00
1-216-114-00
1-216-101-00
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
4.7K
150K
220
510K
150K
5%
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/10W
1/10W
R712
R713
R714
R715
R716
1-216-095-00
1-216-089-11
1-216-089-11
1-216-101-00
1-216-097-11
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
82K
47K
47K
150K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R718
R719
R720
R721
R722
1-216-041-00
1-216-041-00
1-216-041-00
1-216-097-11
1-216-097-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
470
470
470
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R723
1-216-097-11 RES-CHIP
100K
5%
1/10W
CD MOTOR
Part No.
Description
R724
R725
R726
R731
R732
1-216-097-11
1-216-097-11
1-216-097-11
1-216-081-00
1-216-081-00
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
22K
22K
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
R733
R734
R735
R737
R738
1-216-097-11
1-216-001-00
1-216-065-11
1-216-089-11
1-216-069-00
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
100K
10
4.7K
47K
6.8K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R741
R742
R743
R745
R750
1-216-105-11
1-216-101-00
1-216-101-00
1-216-109-00
1-216-076-00
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220K
150K
150K
330K
13K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R751
R752
R758
R760
R762
1-216-077-11
1-216-085-00
1-216-218-00
1-216-097-11
1-216-113-00
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
15K
33K
6.8K
100K
470K
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/10W
1/10W
R763
R764
R765
R766
R767
1-216-061-00
1-216-061-00
1-216-073-00
1-216-121-11
1-216-073-00
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
3.3K
3.3K
10K
1M
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R768
R770
R771
R776
R777
1-216-105-11
1-216-049-11
1-216-025-11
1-216-073-00
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
220K
1K
100
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R778
R780
R781
R787
R788
1-216-049-11
1-216-049-11
1-216-073-00
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1K
1K
10K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R789
R790
R791
R795
R796
1-216-033-00
1-216-049-11
1-216-049-11
1-216-041-00
1-216-049-11
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
220
1K
1K
470
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R797
R798
R799
1-216-049-11 RES-CHIP
1-216-049-11 RES-CHIP
1-216-049-11 RES-CHIP
1K
1K
1K
5%
5%
5%
1/10W
1/10W
1/10W
< VIBRATOR >
X701
1-781-462-41 VIBRATOR, CRYSTAL (16.9344MHz)
*************************************************************
A-3322-635-A CD MOTOR BOARD, COMPLETE
**************************
*
< CAPACITOR >
C801
– 111 –
1-163-021-11 CERAMIC CHIP
0.01uF
10%
50V
CD MOTOR
Ref. No.
C802
C803
C804
Part No.
DG
Description
Remark
1-164-161-11 CERAMIC CHIP
1-163-038-00 CERAMIC CHIP
1-126-934-11 ELECT
0.0022uF 10%
0.1uF
220uF
20%
100V
25V
16V
< CONNECTOR >
* CN801
1-785-677-11 PIN, CONNECTOR (PC BOARD) 11P
< IC >
IC801
IC802
8-759-344-00 IC NJM2100E(TE2)
8-759-591-65 IC BA6892FP-E2
< JUMPER RESISTOR >
JC801
1-216-295-00 SHORT
0
Ref. No.
Part No.
Description
C610
C611
C612
C613
C614
1-164-156-11
1-164-156-11
1-164-156-11
1-163-251-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
100PF
100PF
Remark
C615
C616
C617
C619
C620
1-164-156-11
1-164-156-11
1-164-156-11
1-126-207-11
1-107-823-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
33uF
0.47uF
C621
C622
C626
C627
C628
1-107-826-11
1-107-725-11
1-163-021-11
1-164-156-11
1-126-205-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
0.1uF
0.1uF
0.01uF
0.1uF
47uF
20%
16V
16V
50V
25V
6.3V
C629
C632
C633
C634
C635
1-126-205-11
1-126-603-11
1-126-603-11
1-162-970-11
1-126-205-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
47uF
4.7uF
4.7uF
0.01uF
47uF
20%
20%
20%
10%
20%
6.3V
35V
35V
25V
6.3V
C637
C639
C640
C641
C642
1-126-603-11
1-124-779-00
1-126-603-11
1-163-021-11
1-126-205-11
ELECT CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
ELECT CHIP
4.7uF
10uF
4.7uF
0.01uF
47uF
20%
20%
20%
10%
20%
35V
16V
35V
50V
6.3V
5%
5%
25V
25V
25V
50V
50V
20%
10%
25V
25V
25V
4V
16V
10%
10%
10%
< TRANSISTOR >
Q801
Q802
Q803
Q804
Q805
8-729-027-56
8-729-027-60
8-729-027-60
8-729-027-56
8-729-900-53
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC143TKA-T146
DTC144TKA-T146
DTC144TKA-T146
DTC143TKA-T146
DTC114EK
Q806
Q807
8-729-903-46 TRANSISTOR 2SB1132-P
8-729-027-46 TRANSISTOR DTC114YKA-T146
< RESISTOR >
R801
R802
R803
R804
R805
1-216-081-00
1-216-099-00
1-216-089-11
1-216-081-00
1-216-085-00
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
22K
120K
47K
22K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C644
C645
C646
C650
C651
1-164-156-11
1-164-156-11
1-162-919-11
1-162-966-11
1-162-966-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
22PF
5%
0.0022uF 10%
0.0022uF 10%
25V
25V
50V
50V
50V
R806
R807
R808
R809
R810
1-216-065-11
1-216-073-00
1-216-097-11
1-216-073-00
1-216-089-11
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
4.7K
10K
100K
10K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
C655
C657
C659
C660
C662
1-162-970-11
1-162-970-11
1-163-021-11
1-126-205-11
1-163-038-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.01uF
47uF
0.1uF
10%
10%
10%
20%
25V
25V
50V
6.3V
25V
R811
1-216-198-11 RES-CHIP
1K
5%
1/8W
C663
C664
C665
C668
C669
1-162-915-11
1-126-206-11
1-126-206-11
1-164-156-11
1-164-360-11
CERAMIC CHIP
ELECT CHIP
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
100uF
100uF
0.1uF
0.1uF
0.5PF
20%
20%
50V
6.3V
6.3V
25V
16V
C670
C672
C673
C675
C676
1-126-205-11
1-162-970-11
1-162-912-11
1-162-927-11
1-162-927-11
ELECT CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
47uF
0.01uF
7PF
100PF
100PF
20%
10%
0.5PF
5%
5%
6.3V
25V
50V
50V
50V
C680
C681
C682
C683
C684
1-163-224-11
1-164-156-11
1-163-038-00
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
7PF
0.1uF
0.1uF
0.001uF
0.001uF
0.25PF 50V
25V
25V
10%
50V
10%
50V
C685
C686
C687
1-162-927-11 CERAMIC CHIP
1-162-927-11 CERAMIC CHIP
1-163-038-00 CERAMIC CHIP
100PF
100PF
0.1uF
5%
5%
< SWITCH >
S801
1-762-812-11 SWITCH, LEAF (LIMIT)
*************************************************************
A-3322-531-A DG BOARD, COMPLETE
*******************
*
< CAPACITOR >
C601
C602
C604
C605
C606
1-162-919-11
1-162-919-11
1-163-235-11
1-164-156-11
1-162-927-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
22PF
22PF
0.1uF
100PF
5%
5%
5%
5%
50V
50V
50V
25V
50V
C607
C608
C609
1-162-927-11 CERAMIC CHIP
1-162-916-11 CERAMIC CHIP
1-162-916-11 CERAMIC CHIP
100PF
12PF
12PF
5%
5%
5%
50V
50V
50V
– 112 –
50V
50V
25V
DG
Ref. No.
Part No.
Description
C689
C690
C691
C692
C693
1-164-156-11
1-163-259-11
1-162-964-11
1-162-964-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
220PF
0.001uF
0.001uF
0.001uF
Remark
C694
C695
C696
C697
C699
1-162-964-11
1-162-964-11
1-163-021-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.01uF
0.01uF
0.01uF
Part No.
Description
5%
10%
10%
10%
25V
50V
50V
50V
50V
Ref. No.
FB631
FB632
FB633
FB634
FB636
1-500-445-21
1-500-445-21
1-469-185-11
1-469-185-11
1-500-445-21
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FERRITE, EMI (SMD)
10%
10%
10%
10%
10%
50V
50V
50V
25V
25V
FB637
FB638
FB639
FB640
FB641
1-500-445-21
1-500-445-21
1-500-445-21
1-500-445-21
1-500-445-21
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FB642
FB643
FB644
FB645
FB646
1-500-445-21
1-500-445-21
1-500-445-21
1-500-445-21
1-500-445-21
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FB647
FB648
FB649
FB650
FB651
1-500-445-21
1-216-295-00
1-500-445-21
1-216-821-11
1-216-825-11
FERRITE, EMI (SMD)
SHORT
0
FERRITE, EMI (SMD)
METAL CHIP
1K
METAL CHIP
2.2K
FB652
FB653
FB654
FB655
FB656
1-216-295-00
1-216-295-00
1-500-445-21
1-469-185-11
1-469-185-11
SHORT
0
SHORT
0
FERRITE, EMI (SMD)
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
FB657
FB660
FB661
FB662
FB663
1-469-185-11
1-500-445-21
1-500-445-21
1-500-445-21
1-500-445-21
FERRITE BEAD INDUCTOR
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FB664
FB665
FB666
FB671
FB672
1-500-445-21
1-500-445-21
1-216-815-11
1-500-445-21
1-500-445-21
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
METAL CHIP
330
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FB673
1-500-445-21 FERRITE, EMI (SMD)
< CONNECTOR >
*
*
*
*
CN601
CN602
CN603
CN604
CN605
1-793-115-21
1-793-116-21
1-580-055-21
1-785-370-21
1-784-687-41
CONNECTOR, FFC/FPC 21P
CONNECTOR, FFC/FPC 23P
PIN, CONNECTOR (SMD) 2P
CONNECTOR, FFC/FPC 26P
PIN, CONNECTOR (PC BOARD) 7P
< DIODE >
D602
D603
8-719-988-61 DIODE 1SS355TE-17
8-719-988-61 DIODE 1SS355TE-17
< FERRITE BEAD >
FB601
FB602
FB603
FB604
FB605
1-500-445-21
1-216-821-11
1-216-821-11
1-216-295-00
1-216-821-11
FERRITE, EMI (SMD)
METAL CHIP
1K
METAL CHIP
1K
SHORT
0
METAL CHIP
1K
FB606
FB607
FB608
FB609
FB610
1-216-295-00
1-500-445-21
1-216-821-11
1-216-821-11
1-412-985-11
SHORT
0
FERRITE, EMI (SMD)
METAL CHIP
1K
METAL CHIP
1K
INDUCTOR
3.3uH
FB611
FB612
FB613
FB614
FB615
1-500-445-21
1-469-185-11
1-500-445-21
1-500-445-21
1-500-445-21
FERRITE, EMI (SMD)
FERRITE BEAD INDUCTOR
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FB616
FB617
FB618
FB619
FB620
1-500-445-21
1-500-445-21
1-500-445-21
1-500-445-21
1-500-445-21
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FB621
FB622
FB623
FB624
FB625
1-500-445-21
1-500-445-21
1-500-445-21
1-500-445-21
1-500-445-21
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FB626
FB627
FB628
FB629
FB630
1-500-445-21
1-216-295-00
1-500-445-21
1-500-445-21
1-469-125-21
FERRITE, EMI (SMD)
SHORT
0
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
5%
5%
1/16W
1/16W
5%
1/16W
5%
5%
1/16W
1/16W
< FILTER >
*
*
*
*
FL601
FL602
FL603
FL604
FL605
1-239-901-21
1-239-901-21
1-239-899-21
1-239-899-21
1-239-899-21
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FILTER, CHIP EMI
FL606
FL607
FL608
FL611
FL612
1-239-899-21
1-125-971-21
1-125-971-21
1-125-971-21
1-125-971-21
FILTER, CHIP EMI
FILTER, 3 TERMINAL NOISE
FILTER, 3 TERMINAL NOISE
FILTER, 3 TERMINAL NOISE
FILTER, 3 TERMINAL NOISE
* FL619
* FL620
– 113 –
1-125-971-21 FILTER, 3 TERMINAL NOISE
1-125-971-21 FILTER, 3 TERMINAL NOISE
Remark
5%
5%
1/16W
1/16W
5%
1/16W
DG
Ref. No.
Part No.
Description
Remark
< IC >
IC601
IC602
IC603
IC604
IC605
8-759-670-32
8-759-040-83
8-759-561-36
8-759-243-19
8-759-591-61
IC
IC
IC
IC
IC
RU8X13MF-0102
BA6287F
PCM3003E/T2
TC7SU04F
TC7WHU04FU
IC606
8-759-447-77 IC TC7WH74FU(TR12R)
< JUMPER RESISTOR >
JC601
JC602
JC603
JC605
JC606
1-216-049-11
1-216-295-00
1-216-049-11
1-216-295-00
1-216-296-00
RES-CHIP
SHORT
RES-CHIP
SHORT
SHORT
1K
0
1K
0
0
JC607
JC608
JC609
JC610
JC611
1-216-295-00
1-216-295-00
1-216-821-11
1-216-821-11
1-216-821-11
SHORT
SHORT
METAL CHIP
METAL CHIP
METAL CHIP
0
0
1K
1K
1K
JC612
JC613
JC614
JC615
JC616
1-216-821-11
1-216-864-11
1-216-049-11
1-216-295-00
1-216-295-00
METAL CHIP
METAL CHIP
RES-CHIP
SHORT
SHORT
1K
0
1K
0
0
JC617
JC618
JC619
JC620
JC621
1-216-295-00
1-216-295-00
1-500-445-21
1-216-295-00
1-216-864-11
SHORT
0
SHORT
0
FERRITE, EMI (SMD)
SHORT
0
METAL CHIP
0
JC622
JC623
JC626
JC627
JC631
1-216-296-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-864-11
SHORT
SHORT
SHORT
SHORT
METAL CHIP
JC632
JC634
JC635
JC639
JC641
1-216-295-00
1-216-295-00
1-216-295-00
1-500-445-21
1-216-295-00
SHORT
0
SHORT
0
SHORT
0
FERRITE, EMI (SMD)
SHORT
0
JC651
JC652
1-216-295-00 SHORT
1-412-989-11 INDUCTOR
0
0
0
0
0
0
6.8uH
< COIL >
L601
L602
L603
L604
L605
1-414-521-21
1-414-398-11
1-414-398-11
1-414-398-11
1-414-398-11
INDUCTOR CHIP
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
10uH
L606
L607
L608
L609
1-414-398-11
1-414-398-11
1-414-398-11
1-414-398-11
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
5%
1/10W
5%
1/10W
Ref. No.
Part No.
Description
L610
L611
L612
L613
L614
1-414-398-11
1-416-107-21
1-414-521-21
1-414-398-11
1-414-398-11
INDUCTOR
10uH
COIL, COMMON MODE CHOKE
INDUCTOR CHIP 10uH
INDUCTOR
10uH
INDUCTOR
10uH
Remark
L615
L616
L617
L618
L619
1-500-445-21
1-500-445-21
1-414-766-22
1-500-445-21
1-414-398-11
FERRITE, EMI (SMD)
FERRITE, EMI (SMD)
INDUCTOR, FERRITE BEAD
FERRITE, EMI (SMD)
INDUCTOR
10uH
L620
L621
L622
1-414-398-11 INDUCTOR
10uH
1-414-521-21 INDUCTOR CHIP 10uH
1-414-521-21 INDUCTOR CHIP 10uH
< TRANSISTOR >
5%
5%
5%
1/16W
1/16W
1/16W
Q603
Q604
Q610
Q611
Q612
5%
5%
5%
1/16W
1/16W
1/10W
Q616
Q617
Q620
8-729-402-84
8-729-402-84
8-729-027-46
8-729-031-43
8-729-101-07
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
XN4601
XN4601
DTC114YKA-T146
IMD9A-T108
2SB798-DL
8-729-027-46 TRANSISTOR DTC114YKA-T146
8-729-019-72 TRANSISTOR 2SB1260
8-729-046-16 TRANSISTOR UMG5NTR
< RESISTOR >
5%
5%
1-216-821-11
1-216-049-11
1-216-821-11
1-500-329-21
1-216-073-00
METAL CHIP
1K
RES-CHIP
1K
METAL CHIP
1K
FERRITE BEAD INDUCTOR
METAL CHIP
10K
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
R601
R602
R603
R604
R605
5%
1/10W
1/16W
R606
R607
R608
R609
R610
1-216-073-00
1-216-073-00
1-216-833-11
1-216-097-11
1-216-097-11
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
10K
10K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/16W
1/10W
1/10W
R611
R612
R613
R614
R615
1-216-845-11
1-216-097-11
1-216-833-11
1-216-857-11
1-216-833-11
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
100K
100K
10K
1M
10K
5%
5%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
1/16W
R616
R617
R618
R619
R620
1-216-845-11
1-216-809-11
1-216-809-11
1-216-845-11
1-216-851-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100
100
100K
330K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R621
R622
R623
R624
R625
1-216-073-00
1-216-833-11
1-216-833-11
1-216-833-11
1-216-833-11
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
10K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/16W
1/16W
R626
R627
R628
1-216-073-00 METAL CHIP
1-216-089-11 RES-CHIP
1-216-841-11 METAL CHIP
10K
47K
47K
5%
5%
5%
1/10W
1/10W
1/16W
– 114 –
DG
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
R629
R630
R631
R632
R633
1-216-833-11
1-216-833-11
1-216-821-11
1-216-821-11
1-216-833-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
10K
10K
1K
1K
10K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
*
A-3322-656-A FL BOARD, COMPLETE
*******************
R634
R636
R637
R638
R639
1-216-833-11
1-216-851-11
1-216-109-00
1-216-841-11
1-216-847-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
330K
330K
47K
150K
5%
5%
5%
5%
5%
1/16W
1/16W
1/10W
1/16W
1/16W
R640
R641
R643
R644
R646
1-216-821-11
1-216-843-11
1-216-809-11
1-216-833-11
1-216-041-00
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
1K
68K
100
10K
470
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/10W
R647
R648
R649
R650
R651
1-216-089-11
1-216-833-11
1-216-835-11
1-216-833-11
1-216-835-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
47K
10K
15K
10K
15K
5%
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/16W
1/16W
R652
R653
R654
R655
R656
1-500-329-21
1-216-073-00
1-216-833-11
1-216-073-00
1-216-833-11
FERRITE BEAD INDUCTOR
METAL CHIP
10K
RES-CHIP
10K
METAL CHIP
10K
RES-CHIP
10K
5%
5%
5%
5%
1/10W
1/16W
1/10W
1/16W
R657
R658
R659
R660
R661
1-216-238-11
1-216-853-11
1-216-817-11
1-216-841-11
1-216-857-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
5%
5%
5%
5%
5%
1/8W
1/16W
1/16W
1/16W
1/16W
R662
R663
R664
R665
R666
1-216-037-00
1-216-821-11
1-216-821-11
1-216-073-00
1-500-329-21
METAL CHIP
330
METAL CHIP
1K
METAL CHIP
1K
METAL CHIP
10K
FERRITE BEAD INDUCTOR
5%
5%
5%
5%
1/10W
1/16W
1/16W
1/10W
R667
R668
R669
R670
R671
1-500-329-21
1-216-815-11
1-216-857-11
1-216-841-11
1-216-821-11
FERRITE BEAD INDUCTOR
METAL CHIP
330
METAL CHIP
1M
METAL CHIP
47K
METAL CHIP
1K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R672
R674
R691
R692
R693
1-216-821-11
1-216-857-11
1-216-821-11
1-216-025-11
1-216-025-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1K
1M
1K
100
100
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/10W
1/10W
R694
R695
1-216-821-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
1K
5%
5%
1/16W
1/16W
Remark
3-039-978-01 HOLDER (FL)
3-042-764-01 SHEET (FL), ADHESIVE
3-846-312-01 SPACER
< CAPACITOR >
C601
C602
C603
C604
C605
1-126-964-11
1-163-021-11
1-163-133-00
1-104-664-11
1-107-682-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
0.01uF
470PF
47uF
1uF
20%
10%
5%
20%
10%
50V
50V
50V
10V
16V
C606
C607
C608
C609
C614
1-163-021-11
1-163-009-11
1-163-243-11
1-163-251-11
1-163-259-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.001uF
47PF
100PF
220PF
10%
10%
5%
5%
5%
50V
50V
50V
50V
50V
C621
C622
C623
C624
C625
1-163-259-11
1-164-005-11
1-164-005-11
1-164-005-11
1-164-005-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.47uF
0.47uF
0.47uF
0.47uF
5%
50V
25V
25V
25V
25V
< CONNECTOR >
CN601
47K
470K
470
47K
1M
Description
FL
1-695-371-31 CONNECTOR, FFC/FPC 10P
< FLOURESCENT INDICATOR >
FL401
1-517-916-11 INDICATOR TUBE, FLUORESCENT
< IC >
IC601
8-759-663-70 IC ML9206-03MBZ060
< TRANSISTOR >
Q612
Q613
8-729-027-44 TRANSISTOR DTC114TKA-T146
8-729-027-44 TRANSISTOR DTC114TKA-T146
< RESISTOR >
R601
R602
R605
R606
R609
1-216-073-00
1-216-017-11
1-216-073-00
1-216-017-11
1-216-041-00
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
10K
47
10K
47
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R610
1-216-049-11 RES-CHIP
1K
5%
1/10W
R611
1-216-049-11 RES-CHIP
1K
5%
1/10W
R612
1-216-041-00 METAL CHIP
470
5%
1/10W
R613
1-216-049-11 RES-CHIP
1K
5%
1/10W
*************************************************************
< VIBRATOR >
X601
1-767-179-21 VIBRATOR, CERAMIC (12MHz)
X602
1-781-183-11 VIBRATOR, CRYSTAL (32.768kHz)
X603
1-760-173-11 VIBRATOR, CRYSTAL (22.5792MHz)
*************************************************************
– 115 –
JACK
KEY
LED
Ref. No.
Part No.
*
1-675-219-11 JACK BOARD
***********
Description
Remark
Ref. No.
D603
D603
< CONNECTOR >
D604
* CN306
1-573-455-11 PLUG, CONNECTOR 4P
D604
< DIODE >
D605
D301
D302
D303
D304
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
D605
< FERRITE BEAD >
FB101
FB102
FB201
FB202
FB301
1-216-295-00
1-469-152-11
1-216-295-00
1-469-152-11
1-216-295-00
SHORT
0
FERRITE, EMI (SMD)
SHORT
0
FERRITE, EMI (SMD)
SHORT
0
FB302
1-469-152-11 FERRITE, EMI (SMD)
< JACK >
J301
J302
1-779-050-11 JACK (i)
1-779-050-11 JACK (LINE IN)
Part No.
Description
Remark
8-719-078-08 LED SLA-362MT-T31XFG (INSERT/TIMER)
(GREEN)
8-719-078-09 LED SLR-332DC-T32MN (INSERT/TIMER)
(ORANGE)
8-719-078-08 LED SLA-362MT-T31XFG (NO/CANCEL)
(GREEN)
8-719-078-09 LED SLR-332DC-T32MN (NO/CANCEL)
(ORANGE)
8-719-078-08 LED SLA-362MT-T31XFG (YES/ENTER)
(GREEN)
D606
D606
D607
D607
8-719-078-09 LED SLR-332DC-T32MN (YES/ENTER)
(ORANGE)
8-719-078-08 LED SLA-362MT-T31XFG (DISPLAY) (GREEN)
8-719-078-09 LED SLR-332DC-T32MN (DISPLAY) (ORANGE)
8-719-078-08 LED SLA-362MT-T31XFG (4/GHI) (GREEN)
8-719-078-09 LED SLR-332DC-T32MN (4/GHI) (ORANGE)
D608
D609
D610
D610
D611
8-719-077-79
8-719-077-79
8-719-078-08
8-719-078-09
8-719-078-08
LED
LED
LED
LED
LED
SLR-332VRT32 (abc)
SLR-332VRT32 (ABC)
SLA-362MT-T31XFG (1) (GREEN)
SLR-332DC-T32MN (1) (ORANGE)
SLA-362MT-T31XFG (1) (GREEN)
D611
D612
D612
D613
D613
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
LED
LED
LED
LED
LED
SLR-332DC-T32MN (1) (ORANGE)
SLA-362MT-T31XFG (2/ABC) (GREEN)
SLR-332DC-T32MN (2/ABC) (ORANGE)
SLA-362MT-T31XFG (3/DEF) (GREEN)
SLR-332DC-T32MN (3/DEF) (ORANGE)
D614
D614
D615
D615
D616
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
LED
LED
LED
LED
LED
SLA-362MT-T31XFG (DISPLAY) (GREEN)
SLR-332DC-T32MN (DISPLAY) (ORANGE)
SLA-362MT-T31XFG (4/GHI) (GREEN)
SLR-332DC-T32MN (4/GHI) (ORANGE)
SLA-362MT-T31XFG (5/JKL) (GREEN)
D616
D617
D617
D618
D618
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
LED
LED
LED
LED
LED
SLR-332DC-T32MN (5/JKL) (ORANGE)
SLA-362MT-T31XFG (6/MNO) (GREEN)
SLR-332DC-T32MN (6/MNO) (ORANGE)
SLA-362MT-T31XFG (7/PQRS) (GREEN)
SLR-332DC-T32MN (7/PQRS) (ORANGE)
D619
D619
D620
D620
D621
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
LED
LED
LED
LED
LED
SLA-362MT-T31XFG (7/PQRS) (GREEN)
SLR-332DC-T32MN (7/PQRS) (ORANGE)
SLA-362MT-T31XFG (8/TUV) (GREEN)
SLR-332DC-T32MN (8/TUV) (ORANGE)
SLA-362MT-T31XFG (9/WXYZ) (GREEN)
D621
D622
D622
D623
D623
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
LED
LED
LED
LED
LED
SLR-332DC-T32MN (9/WXYZ) (ORANGE)
SLA-362MT-T31XFG (SYMBOL) (GREEN)
SLR-332DC-T32MN (SYMBOL) (ORANGE)
SLA-362MT-T31XFG (SYMBOL) (GREEN)
SLR-332DC-T32MN (SYMBOL) (ORANGE)
D624
D624
D625
8-719-078-08 LED SLA-362MT-T31XFG (0/10) (GREEN)
8-719-078-09 LED SLR-332DC-T32MN (0/10) (ORANGE)
8-719-078-08 LED SLA-362MT-T31XFG (>10 AM/PM)
(GREEN)
8-719-078-09 LED SLR-332DC-T32MN (>10 AM/PM)
(ORANGE)
< RESISTOR >
R103
1-216-033-00 METAL CHIP
220
5%
1/10W
R203
1-216-033-00 METAL CHIP
220
5%
1/10W
*************************************************************
1-675-223-11 KEY BOARD
**********
*
< CONNECTOR >
* CN603 1-695-333-41 PIN, CONNECTOR (PC BOARD) 10P
*************************************************************
A-3062-399-A LED BOARD, COMPLETE (ORANGE)
A-3322-633-A LED BOARD, COMPLETE (GREEN)
********************
*
*
< CAPACITOR >
C611
1-126-794-11 ELECT
4.7uF
20%
25V
< CONNECTOR >
* CN602
1-695-374-31 PIN, CONNECTOR (PC BOARD) 13P
< DIODE >
D601
D602
D602
8-719-077-79 LED SLR-332VRT32 (HIGH SPEED)
8-719-078-08 LED SLA-362MT-T31XFG (DELETE/CLOCK)
(GREEN)
8-719-078-09 LED SLR-332DC-T32MN (DELETE/CLOCK)
(ORANGE)
D625
NOTE: There are two different colors of LEDs on the LED board.
In service, check the color of the set before replacing parts.
Color of the set
Color of LEDs
BLACK ..................... GREEN
WHITE ...................... GREEN
BLUE ........................ GREEN
ORANGE .................. ORANGE
– 116 –
LED
Ref. No.
Part No.
Description
Remark
< IC >
IC602
JC601
JC602
JC603
JC604
Part No.
Description
Remark
R638
1-216-033-00 METAL CHIP
220
5%
R641
1-216-025-11 RES-CHIP
100
5%
< JUMPER RESISTOR >
R641
1-216-033-00 METAL CHIP
220
5%
SHORT
SHORT
SHORT
SHORT
R643
1-216-025-11 RES-CHIP
100
5%
R643
1-216-033-00 METAL CHIP
220
5%
< TRANSISTOR >
R646
1-216-025-11 RES-CHIP
100
5%
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
R646
1-216-033-00 METAL CHIP
220
5%
R648
R649
R650
1-216-045-00 METAL CHIP
1-216-048-00 METAL CHIP
1-216-056-00 RES-CHIP
680
910
2K
5%
5%
5%
R651
R666
1-216-061-00 METAL CHIP
1-216-025-11 RES-CHIP
3.3K
100
5%
5%
R666
1-216-033-00 METAL CHIP
220
5%
R667
1-216-025-11 RES-CHIP
100
5%
R667
1-216-033-00 METAL CHIP
220
5%
R668
1-216-025-11 RES-CHIP
100
5%
R668
1-216-033-00 METAL CHIP
220
5%
R670
1-216-025-11 RES-CHIP
100
5%
R670
1-216-033-00 METAL CHIP
220
5%
R671
1-216-025-11 RES-CHIP
100
5%
R671
1-216-033-00 METAL CHIP
220
5%
R672
1-216-025-11 RES-CHIP
100
5%
R672
1-216-033-00 METAL CHIP
220
5%
R673
1-216-025-11 RES-CHIP
100
5%
R673
1-216-033-00 METAL CHIP
220
5%
R674
1-216-025-11 RES-CHIP
100
5%
R674
1-216-033-00 METAL CHIP
220
5%
R675
1-216-025-11 RES-CHIP
100
5%
R675
1-216-033-00 METAL CHIP
220
5%
R676
1-216-025-11 RES-CHIP
100
5%
8-749-016-97 IC NJL62H400A
1-216-295-00
1-216-296-00
1-216-295-00
1-216-295-00
Ref. No.
0
0
0
0
Q603
Q604
Q606
Q607
Q608
8-729-027-58
8-729-901-88
8-729-027-58
8-729-027-58
8-729-120-28
DTC143ZKA-T146
2SC2411K-CR
DTC143ZKA-T146
DTC143ZKA-T146
2SC1623-L5L6
Q609
Q610
Q611
8-729-120-28 TRANSISTOR 2SC1623-L5L6
8-729-120-28 TRANSISTOR 2SC1623-L5L6
8-729-120-28 TRANSISTOR 2SC1623-L5L6
< RESISTOR >
R603
1-216-025-11 RES-CHIP
100
5%
R603
1-216-033-00 METAL CHIP
220
5%
R614
R615
R617
1-216-085-00 METAL CHIP
1-216-033-00 METAL CHIP
1-216-025-11 RES-CHIP
33K
220
100
5%
5%
5%
R617
1-216-033-00 METAL CHIP
220
5%
R620
1-216-025-11 RES-CHIP
100
5%
R620
1-216-033-00 METAL CHIP
220
5%
R622
R624
1-216-051-00 METAL CHIP
1-216-033-00 METAL CHIP
1.2K
220
5%
5%
R626
R628
1-216-033-00 METAL CHIP
1-216-025-11 RES-CHIP
220
100
5%
5%
R628
1-216-033-00 METAL CHIP
220
5%
R631
1-216-074-00 RES-CHIP
100
5%
R631
1-216-082-00 RES-CHIP
220
5%
R633
1-216-025-11 RES-CHIP
100
5%
R633
1-216-033-00 METAL CHIP
220
5%
R636
1-216-025-11 RES-CHIP
100
5%
R636
1-216-033-00 METAL CHIP
220
5%
R638
1-216-025-11 RES-CHIP
100
5%
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
1/10W
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
1/10W
1/10W
1/10W
(GREEN)
1/10W
(ORANGE)
1/8W
(GREEN)
1/8W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
1/10W
1/10W
1/10W
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
NOTE: There are two different colors of LEDs on the LED board.
In service, check the color of the set before replacing parts.
Color of the set
Color of LEDs
BLACK ..................... GREEN
WHITE ...................... GREEN
BLUE ........................ GREEN
ORANGE .................. ORANGE
– 117 –
LED
Ref. No.
MAIN
Part No.
Description
Remark
R676
1-216-033-00 METAL CHIP
220
5%
R677
1-216-025-11 RES-CHIP
100
5%
R677
1-216-033-00 METAL CHIP
220
5%
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
< SWITCH >
S601
S601
S602
S602
S603
1-692-014-11
1-762-798-11
1-692-014-11
1-762-798-11
1-692-014-11
S603
S604
1-762-798-11 SWITCH, KEY BOARD (STANDBY) (ORANGE)
1-692-014-11 SWITCH, KEY BOARD (MONO/ST/REPEAT)
(GREEN)
1-762-798-11 SWITCH, KEY BOARD (MONO/ST/REPEAT)
(ORANGE)
1-692-014-11 SWITCH, KEY BOARD
(AUTO PRESET, SHUF/PGM) (GREEN)
1-762-798-11 SWITCH, KEY BOARD
(AUTO PRESET, SHUF/PGM) (ORANGE)
S604
S605
S605
SWITCH, KEY BOARD (POWER) (GREEN)
SWITCH, KEY BOARD (POWER) (ORANGE)
SWITCH, KEY BOARD (SLEEP) (GREEN)
SWITCH, KEY BOARD (SLEEP) (ORANGE)
SWITCH, KEY BOARD (STANDBY) (GREEN)
S606
1-692-014-11 SWITCH, KEY BOARD (EDIT) (GREEN)
S606
1-762-798-11 SWITCH, KEY BOARD (EDIT) (ORANGE)
*************************************************************
A-3322-636-A MAIN BOARD, COMPLETE
*********************
*
3-039-961-01 SPRING (IC)
3-831-441-99 CUSHION (A)
7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
< CAPACITOR >
C101
C102
C103
C104
C105
1-126-767-11
1-126-963-11
1-126-963-11
1-163-251-11
1-163-021-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
1000uF
4.7uF
4.7uF
100PF
0.01uF
20%
20%
20%
5%
10%
16V
50V
50V
50V
50V
C106
C107
C108
C109
C110
1-136-165-00
1-136-165-00
1-126-960-11
1-126-964-11
1-126-961-11
MYLAR
MYLAR
ELECT
ELECT
ELECT
0.1uF
0.1uF
1uF
10uF
2.2uF
5%
5%
20%
20%
20%
50V
50V
50V
50V
50V
C111
C112
C113
C114
C115
1-126-961-11
1-126-961-11
1-126-961-11
1-136-157-00
1-136-173-00
ELECT
ELECT
ELECT
MYLAR
MYLAR
2.2uF
2.2uF
2.2uF
0.022uF
0.47uF
20%
20%
20%
5%
5%
50V
50V
50V
50V
50V
C116
C117
C118
C119
C126
1-136-153-00
1-126-963-11
1-126-961-11
1-126-960-11
1-126-960-11
FILM
ELECT
ELECT
ELECT
ELECT
0.01uF
4.7uF
2.2uF
1uF
1uF
5%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C127
1-163-009-11 CERAMIC CHIP
0.001uF
10%
50V
Ref. No.
Part No.
Description
C128
C201
C202
C203
C204
1-163-251-11
1-126-767-11
1-126-963-11
1-126-963-11
1-163-251-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
100PF
1000uF
4.7uF
4.7uF
100PF
5%
20%
20%
20%
5%
Remark
50V
16V
50V
50V
50V
C205
C206
C207
C208
C209
1-163-021-11
1-136-165-00
1-136-165-00
1-126-960-11
1-126-964-11
CERAMIC CHIP
MYLAR
MYLAR
ELECT
ELECT
0.01uF
0.1uF
0.1uF
1uF
10uF
10%
5%
5%
20%
20%
50V
50V
50V
50V
50V
C210
C211
C212
C213
C214
1-126-961-11
1-126-961-11
1-126-961-11
1-126-961-11
1-136-157-00
ELECT
ELECT
ELECT
ELECT
MYLAR
2.2uF
2.2uF
2.2uF
2.2uF
0.022uF
20%
20%
20%
20%
5%
50V
50V
50V
50V
50V
C215
C216
C217
C218
C219
1-136-173-00
1-136-153-00
1-126-963-11
1-126-961-11
1-126-960-11
MYLAR
FILM
ELECT
ELECT
ELECT
0.47uF
0.01uF
4.7uF
2.2uF
1uF
5%
5%
20%
20%
20%
50V
50V
50V
50V
50V
C226
C227
C228
C301
C302
1-126-960-11
1-163-009-11
1-163-251-11
1-104-665-11
1-126-963-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
1uF
0.001uF
100PF
100uF
4.7uF
20%
10%
5%
20%
20%
50V
50V
50V
10V
50V
C303
C306
C307
C308
C309
1-115-877-11
1-126-964-11
1-163-009-11
1-104-665-11
1-126-934-11
ELECT(BLOCK)
ELECT
CERAMIC CHIP
ELECT
ELECT
4700uF
10uF
0.001uF
100uF
220uF
20%
20%
10%
20%
20%
25V
50V
50V
10V
10V
C310
C311
C312
C313
C314
1-104-665-11
1-104-665-11
1-104-665-11
1-126-964-11
1-163-021-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
100uF
100uF
100uF
10uF
0.01uF
20%
20%
20%
20%
10%
10V
10V
10V
50V
50V
C315
C316
C317
C318
C319
1-163-021-11
1-104-665-11
1-107-725-11
1-126-964-11
1-126-960-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
ELECT
0.01uF
100uF
0.1uF
10uF
1uF
10%
20%
10%
20%
20%
50V
10V
16V
50V
50V
C320
C321
C322
C323
C324
1-163-009-11
1-163-009-11
1-126-964-11
1-104-665-11
1-104-665-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
0.001uF
0.001uF
10uF
100uF
100uF
10%
10%
20%
20%
20%
50V
50V
50V
10V
10V
C326
C401
C402
C403
C404
1-126-964-11
1-163-237-11
1-163-104-00
1-164-346-11
1-163-239-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
27PF
30PF
1uF
33PF
20%
5%
5%
5%
50V
50V
50V
16V
50V
C405
C406
C407
1-163-239-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
33PF
0.001uF
0.001uF
5%
10%
10%
50V
50V
50V
NOTE: There are two different colors of LEDs on the LED board.
In service, check the color of the set before replacing parts.
Color of the set
Color of LEDs
BLACK ..................... GREEN
WHITE ...................... GREEN
BLUE ........................ GREEN
ORANGE .................. ORANGE
– 118 –
MAIN
Ref. No.
Part No.
Description
Part No.
Description
C408
C409
C410
C411
C412
1-163-235-11
1-163-234-11
1-107-725-11
1-104-665-11
1-164-346-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
22PF
20PF
0.1uF
100uF
1uF
5%
5%
10%
20%
50V
50V
16V
10V
16V
Remark
Ref. No.
C470
C472
C473
C474
C477
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
100PF
10%
10%
10%
10%
5%
50V
50V
50V
50V
50V
C413
C414
C416
C417
C418
1-104-664-11
1-126-964-11
1-126-919-11
1-163-009-11
1-164-346-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
47uF
10uF
6800uF
0.001uF
1uF
20%
20%
20%
10%
10V
50V
6.3V
50V
16V
C478
C479
C480
C481
C482
1-163-243-11
1-163-009-11
1-163-021-11
1-126-964-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
47PF
0.001uF
0.01uF
10uF
10uF
5%
10%
10%
20%
20%
50V
50V
50V
50V
50V
C419
C420
C421
C422
C423
1-163-021-11
1-126-933-11
1-107-725-11
1-126-925-11
1-163-021-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.01uF
100uF
0.1uF
470uF
0.01uF
10%
20%
10%
20%
10%
50V
16V
16V
10V
50V
C483
C484
C485
C486
C487
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C424
C425
C428
C430
C431
1-163-021-11
1-126-934-11
1-104-664-11
1-163-021-11
1-126-934-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
0.01uF
220uF
47uF
0.01uF
220uF
10%
20%
20%
10%
20%
50V
10V
10V
50V
10V
C488
C489
C490
C491
C492
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C433
C434
C435
C436
C437
1-163-021-11
1-126-964-11
1-163-021-11
1-163-021-11
1-126-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
10uF
0.01uF
0.01uF
10uF
10%
20%
10%
10%
20%
50V
50V
50V
50V
50V
C493
C494
C495
C496
C497
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C438
C439
C440
C441
C443
1-163-021-11
1-126-968-11
1-126-960-11
1-126-960-11
1-126-937-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.01uF
100uF
1uF
1uF
4700uF
10%
20%
20%
20%
20%
50V
50V
50V
50V
16V
C498
C499
C500
C502
C503
1-163-251-11
1-163-251-11
1-163-251-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
0.001uF
0.001uF
5%
5%
5%
10%
10%
50V
50V
50V
50V
50V
C444
C445
C446
C447
C450
1-163-009-11
1-164-161-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.0022uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
100V
50V
50V
50V
C504
C505
C506
C507
C509
1-163-009-11
1-163-243-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
47PF
0.001uF
0.001uF
0.001uF
10%
5%
10%
10%
10%
50V
50V
50V
50V
50V
C451
C452
C453
C454
C455
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C510
C512
C513
C514
C515
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-021-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.01uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C456
C457
C458
C459
C460
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C528
C529
C531
C532
C533
1-104-665-11
1-163-021-11
1-126-933-11
1-126-933-11
1-163-021-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
100uF
0.01uF
100uF
100uF
0.01uF
20%
10%
20%
20%
10%
10V
50V
16V
16V
50V
C461
C462
C463
C464
C465
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C535
C536
C537
C538
C539
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C466
C468
C469
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
0.001uF
0.001uF
0.001uF
10%
10%
10%
50V
50V
50V
C540
1-163-009-11 CERAMIC CHIP
0.001uF
10%
50V
– 119 –
Remark
MAIN
Ref. No.
Part No.
Description
Remark
< CONNECTOR >
CN301
CN303
CN401
CN402
CN403
1-564-778-11
1-785-656-11
1-564-778-11
1-785-662-11
1-568-468-11
PLUG, CONNECTOR (2.5mm) 4P
PIN, CONNECTOR (PC BOARD) 4P
PLUG, CONNECTOR (2.5mm) 4P
PIN, CONNECTOR (PC BOARD) 10P
PIN, CONNECTOR (PC BOARD) 18P
CN404
* CN405
CN406
* CN407
* CN408
1-568-931-11
1-695-333-41
1-695-336-31
1-695-333-41
1-785-661-11
PIN, CONNECTOR (PC BOARD) 26P
PIN, CONNECTOR (PC BOARD) 10P
PIN, CONNECTOR (PC BOARD) 13P
PIN, CONNECTOR (PC BOARD) 10P
PIN, CONNECTOR (PC BOARD) 9P
* CN409
* CN410
CN450
1-785-655-11 PIN, CONNECTOR (PC BOARD) 3P
1-785-654-11 PIN, CONNECTOR (PC BOARD) 2P
1-566-690-11 PLUG, CONNECTOR (2.5mm) 2P
*
*
*
*
*
Ref. No.
FB427
FB428
FB429
FB430
Part No.
Description
1-216-295-00
1-216-073-00
1-216-295-00
1-216-073-00
SHORT
METAL CHIP
SHORT
METAL CHIP
Remark
0
10K
0
10K
5%
1/10W
5%
1/10W
< IC >
IC301
IC302
IC303
IC305
IC401
8-759-543-56
8-759-652-74
8-759-100-96
8-759-636-55
8-752-915-75
IC
IC
IC
IC
IC
LA4601N
M62443FPD61Q
uPC4558G2
M5218AFP
CXP740096-044Q
IC402
IC403
IC404
IC411
8-759-486-73
8-759-649-23
8-759-450-47
8-759-486-73
IC
IC
IC
IC
XC62FP3302PR
XC61CN2802PR
BA05T
XC62FP3302PR
< DIODE >
< JUMPER RESISTOR >
D301
D303
D304
D401
D402
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
JC101
JC102
JC103
JC104
JC105
1-216-296-00
1-216-295-00
1-216-295-00
1-216-296-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
D403
D404
D405
D406
8-719-056-84
8-719-056-85
8-719-056-82
8-719-977-81
DIODE
DIODE
DIODE
DIODE
UDZ-TE-17-7.5B
UDZ-TE-17-8.2B
UDZ-TE-17-6.2B
DTZ33B
JC106
JC107
JC108
JC109
JC113
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
< FERRITE BEAD >
< TRANSISTOR >
FB401
FB402
FB403
FB404
FB405
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
FB406
FB407
FB408
FB409
FB410
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
FB411
FB412
FB413
FB414
FB415
1-216-295-00
1-469-185-11
1-469-185-11
1-216-295-00
1-216-295-00
SHORT
0
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
SHORT
0
SHORT
0
FB416
FB417
FB418
FB419
FB420
1-216-295-00
1-216-295-00
1-216-296-00
1-216-296-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
FB421
FB423
FB424
FB425
FB426
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
1-216-295-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
Q101
Q102
Q103
Q104
Q105
8-729-027-46
8-729-120-28
8-729-027-46
8-729-920-31
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114YKA-T146
2SC1623-L5L6
DTC114YKA-T146
DTC343TK
2SC1623-L5L6
Q106
Q111
Q201
Q202
Q203
8-729-027-46
8-729-920-31
8-729-027-46
8-729-120-28
8-729-027-46
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114YKA-T146
DTC343TK
DTC114YKA-T146
2SC1623-L5L6
DTC114YKA-T146
Q204
Q205
Q206
Q211
Q301
8-729-920-31
8-729-120-28
8-729-027-46
8-729-920-31
8-729-027-24
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC343TK
2SC1623-L5L6
DTC114YKA-T146
DTC343TK
DTA114TKA-T146
Q304
Q305
Q306
Q307
Q308
8-729-900-53
8-729-027-46
8-729-027-23
8-729-900-53
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EK
DTC114YKA-T146
DTA114EKA-T146
DTC114EK
2SC1623-L5L6
Q309
Q310
Q311
Q312
Q313
8-729-027-23
8-729-027-26
8-729-027-24
8-729-027-24
8-729-027-26
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA114EKA-T146
DTA114YKA-T146
DTA114TKA-T146
DTA114TKA-T146
DTA114YKA-T146
– 120 –
MAIN
Ref. No.
Part No.
Description
Part No.
Description
Q401
Q402
Q403
Q405
Q406
8-729-903-10
8-729-018-99
8-729-021-82
8-729-021-82
8-729-903-46
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
FMW1
2SD2394-F
2SD2396K
2SD2396K
2SB1132-P
Remark
R212
R213
R214
R215
R216
1-216-073-00
1-216-689-11
1-216-089-11
1-216-079-00
1-216-113-00
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
10K
39K
47K
18K
470K
5%
0.5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Q407
Q408
Q409
Q411
Q412
8-729-027-26
8-729-027-46
8-729-027-29
8-729-027-26
8-729-027-46
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA114YKA-T146
DTC114YKA-T146
DTA123JKA-T146
DTA114YKA-T146
DTC114YKA-T146
R217
R218
R219
R220
R222
1-216-081-00
1-216-057-00
1-216-047-11
1-216-061-00
1-216-049-11
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
22K
2.2K
820
3.3K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Q415
Q416
Q419
Q420
Q421
8-729-027-29
8-729-027-46
8-729-012-83
8-729-012-83
8-729-027-26
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA123JKA-T146
DTC114YKA-T146
2SK679A
2SK679A
DTA114YKA-T146
R223
R224
R225
R302
R303
1-216-077-11
1-216-049-11
1-216-089-11
1-216-073-00
1-216-073-00
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
15K
1K
47K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Q422
8-729-027-46 TRANSISTOR DTC114YKA-T146
R304
R306
R307
R308
R309
1-216-057-00
1-216-025-11
1-216-073-00
1-216-073-00
1-216-166-00
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
2.2K
100
10K
10K
47
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/8W
R310
R311
R312
R313
R314
1-216-049-11
1-216-049-11
1-216-065-11
1-216-073-00
1-216-073-00
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
1K
1K
4.7K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R315
R316
R317
R318
R319
1-216-073-00
1-216-113-00
1-216-049-11
1-216-121-11
1-216-049-11
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
470K
1K
1M
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R320
R321
R322
R323
R324
1-216-049-11
1-216-097-11
1-216-073-00
1-216-041-00
1-216-049-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
1K
100K
10K
470
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R327
R328
R329
R401
R402
1-216-073-00
1-216-073-00
1-216-025-11
1-216-222-00
1-216-198-11
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
10K
100
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/8W
1/8W
R403
R404
R406
R407
R408
1-216-049-11
1-216-025-11
1-216-308-00
1-216-017-11
1-216-047-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1K
100
4.7
47
820
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R409
R410
R411
R412
R413
1-216-047-11
1-216-041-00
1-216-077-11
1-216-295-00
1-216-053-00
RES-CHIP
METAL CHIP
RES-CHIP
SHORT
METAL CHIP
820
470
15K
0
1.5K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R416
R417
R418
1-216-073-00 METAL CHIP
1-216-049-11 RES-CHIP
1-216-049-11 RES-CHIP
10K
1K
1K
5%
5%
5%
1/10W
1/10W
1/10W
< RESISTOR >
R101
R102
R103
R104
R105
1-216-049-11
1-216-061-00
1-216-025-11
1-216-049-11
1-216-052-00
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
1K
3.3K
100
1K
1.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R106
R107
R108
R109
R110
1-216-111-00
1-216-121-11
1-216-079-00
1-216-073-00
1-216-049-11
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
390K
1M
18K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R111
R112
R113
R114
R115
1-216-077-11
1-216-073-00
1-216-689-11
1-216-089-11
1-216-079-00
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
15K
10K
39K
47K
18K
5%
5%
0.5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R116
R117
R118
R119
R120
1-216-113-00
1-216-081-00
1-216-057-00
1-216-047-11
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
470K
22K
2.2K
820
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R122
R123
R124
R125
R201
1-216-198-11
1-216-077-11
1-216-049-11
1-216-089-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
15K
1K
47K
1K
5%
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/10W
1/10W
R202
R203
R204
R205
R206
1-216-061-00
1-216-025-11
1-216-049-11
1-216-052-00
1-216-111-00
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
3.3K
100
1K
1.3K
390K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R207
R208
R209
R210
R211
1-216-121-11
1-216-079-00
1-216-073-00
1-216-049-11
1-216-077-11
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1M
18K
10K
1K
15K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Ref. No.
– 121 –
Remark
MAIN
Ref. No.
POWER
Part No.
Description
Part No.
Description
R419
R422
R423
R424
R425
1-216-049-11
1-216-073-00
1-216-049-11
1-216-041-00
1-216-041-00
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
1K
10K
1K
470
470
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
Ref. No.
R476
R477
R478
R479
R480
1-216-049-11
1-216-073-00
1-216-049-11
1-216-049-11
1-216-049-11
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
10K
1K
1K
1K
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
R426
R427
R428
R429
R430
1-216-049-11
1-216-073-00
1-216-049-11
1-216-049-11
1-216-049-11
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
10K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R481
R482
R483
R484
R485
1-216-025-11
1-216-049-11
1-216-025-11
1-216-049-11
1-216-065-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
1K
100
1K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R431
R432
R433
R434
R435
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R486
R487
R488
R489
R490
1-216-065-11
1-216-065-11
1-216-041-00
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
4.7K
4.7K
470
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R436
R437
R438
R439
R440
1-216-049-11
1-216-049-11
1-216-049-11
1-216-113-00
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
1K
1K
1K
470K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R491
R492
R493
R494
R496
1-216-049-11
1-216-049-11
1-216-049-11
1-216-073-00
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
1K
1K
1K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R441
R442
R443
R444
R445
1-216-049-11
1-216-085-00
1-216-085-00
1-216-085-00
1-216-085-00
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
33K
33K
33K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R497
R499
R500
R505
R506
1-216-049-11
1-216-089-11
1-216-041-00
1-216-085-00
1-216-073-00
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
47K
470
33K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R446
R447
R449
R450
R451
1-216-085-00
1-216-065-11
1-216-049-11
1-216-049-11
1-216-049-11
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
33K
4.7K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R512
R513
R520
R521
R522
1-216-295-00
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
SHORT
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
1K
1K
1K
1K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R453
R454
R455
R456
R457
1-216-065-11
1-216-113-00
1-216-041-00
1-216-041-00
1-216-049-11
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
4.7K
470K
470
470
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R523
R524
R525
R527
R528
1-216-049-11
1-216-049-11
1-216-049-11
1-216-041-00
1-216-097-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
1K
1K
1K
470
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R458
R459
R460
R461
R462
1-216-049-11
1-216-049-11
1-216-065-11
1-216-081-00
1-216-089-00
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
1K
1K
22K
22K
47K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R529
1-216-097-11 RES-CHIP
100K
5%
1/10W
R463
R464
R465
R466
R467
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R468
R469
R470
R471
R472
1-216-049-11
1-216-049-11
1-216-198-11
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/10W
1/10W
R473
R474
R475
1-216-190-00 RES-CHIP
1-216-190-00 RES-CHIP
1-216-049-11 RES-CHIP
470
470
1K
5%
5%
5%
1/8W
1/8W
1/10W
< VIBRATOR >
X401
1-781-598-11 VIBRATOR, CERAMIC (8MHz)
X402
1-767-697-11 VIBRATOR, CRYSTAL (32kHz)
*************************************************************
A-3322-637-A POWER BOARD, COMPLETE
***********************
*
1-533-233-31 HOLDER, FUSE
< CAPACITOR >
C901
C902
C903
C904
C905
– 122 –
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
0.022uF
0.022uF
0.022uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
POWER
Ref. No.
Part No.
Description
C906
C907
C908
C909
C910
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
0.022uF
0.022uF
0.022uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
Remark
C911
C912
C913
C914
C915
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
0.022uF
0.022uF
0.022uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C916
C917
C918
C919
0 C920
1-163-037-11
1-163-021-11
1-163-021-11
1-163-021-11
1-113-925-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
0.022uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
20%
25V
50V
50V
50V
250V
0 C922
1-113-925-11 CERAMIC
0.01uF
20%
250V
Ref. No.
Part No.
SW
Description
TOP
Remark
< TRANSISTOR >
Q901
Q902
8-729-027-50 TRANSISTOR DTC123JKA-T146
8-729-120-28 TRANSISTOR 2SC1623-L5L6
< RESISTOR >
R901
R902
R905
R906
1-216-073-00
1-216-089-11
1-216-089-11
1-216-073-00
METAL CHIP
RES-CHIP
RES-CHIP
METAL CHIP
10K
47K
47K
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
< RELAY >
RY901
1-755-363-11 RELAY
< TRANSFORMER >
0 T901
1-435-320-11 TRANSFORMER, POWER
*************************************************************
< CONNECTOR >
1-671-115-21 SW BOARD
**********
*
* CN903
1-785-654-11 PIN, CONNECTOR (PC BOARD) 2P
< CONNECTOR >
< DIODE >
* CN601
D901
D902
D903
D904
D905
8-719-046-07
8-719-046-07
8-719-046-07
8-719-046-07
8-719-046-07
DIODE
DIODE
DIODE
DIODE
DIODE
2A02M
2A02M
2A02M
2A02M
2A02M
D906
D907
D908
D909
D910
8-719-046-07
8-719-046-07
8-719-046-07
8-719-063-79
8-719-063-79
DIODE
DIODE
DIODE
DIODE
DIODE
2A02M
2A02M
2A02M
1N4002B
1N4002B
D911
D912
D913
D914
D915
8-719-063-79
8-719-063-79
8-719-988-61
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
1N4002B
1N4002B
1SS355TE-17
1SS355TE-17
1SS355TE-17
< SWITCH >
S601
S602
S604
1-572-126-21 SWITCH, PUSH (1 KEY) (REC POSITION)
1-572-126-21 SWITCH, PUSH (1 KEY) (PACK OUT)
1-771-264-11 SWITCH, PUSH (DETECTION) (1 KEY)
(PLAY POSITION)
*************************************************************
1-576-099-11 FUSE (0.8A/250V)
1-576-105-11 FUSE (2.5A/250V)
1-576-107-11 FUSE (3.15A/250V)
< AC INLET >
0 J901
1-540-009-11 INLET, AC (- AC IN)
< JUMPER RESISTOR >
JC901
1-216-296-00 SHORT
1-675-213-11 TOP BOARD
**********
*
< FUSE >
0 F901
0 F902
0 F903
0
3-363-898-01 CUSHION
3-831-441-11 CUSHION (B)
< RESISTOR >
R654
R655
R656
R657
R658
1-216-045-00
1-216-048-00
1-216-051-00
1-216-056-00
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
680
910
1.2K
2K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R660
R661
R662
R663
R664
1-216-045-00
1-216-048-00
1-216-051-00
1-216-056-00
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
METAL CHIP
680
910
1.2K
2K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R665
1-216-069-00 METAL CHIP
6.8K
5%
1/10W
< SWITCH >
< IC LINK >
0 PS901
1-506-486-11 PIN, CONNECTOR 7P
1-532-679-00 LINK, IC ICP-N15 (0.6A)
S633
S634
S635
1-762-798-11 SWITCH, KEY BOARD (MEGA BASS)
1-762-798-11 SWITCH, KEY BOARD (SOUND)
1-762-798-11 SWITCH, KEY BOARD (MD x)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
– 123 –
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
TOP
Ref. No.
S636
S637
S638
S640
S641
TUNER
Part No.
Description
1-762-798-11
1-762-798-11
1-762-798-11
1-762-798-11
1-762-798-11
SWITCH, KEY BOARD (MD u)
SWITCH, KEY BOARD (RADIO/BAND)
SWITCH, KEY BOARD (CD x)
SWITCH, KEY BOARD (VOLUME –)
SWITCH, KEY BOARD (VOLUME +)
Remark
S642
1-762-798-11 SWITCH, KEY BOARD (REC/REC MODE)
S643
1-762-798-11 SWITCH, KEY BOARD (CD u)
S644
1-762-798-11 SWITCH, KEY BOARD (TUNE > +)
S645
1-762-798-11 SWITCH, KEY BOARD (TUNE . –)
S646
1-762-798-11 SWITCH, KEY BOARD (LINE/LINE LEVEL)
*************************************************************
Ref. No.
Part No.
Description
C41
C42
C43
C44
C45
1-163-017-00
1-163-133-00
1-163-133-00
1-163-251-11
1-163-021-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.0047uF
470PF
470PF
100PF
0.01uF
5%
5%
5%
5%
10%
50V
50V
50V
50V
50V
Remark
C46
C47
C63
C67
C71
1-163-009-11
1-163-251-11
1-163-001-11
1-126-964-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.001uF
100PF
220PF
10uF
0.001uF
10%
5%
10%
20%
10%
50V
50V
50V
50V
50V
< FILTER >
A-3322-634-A TUNER BOARD, COMPLETE
***********************
*
CF1
CF2
CF3
< CAPACITOR >
C1
C2
C3
C4
C5
1-163-009-11
1-163-227-11
1-163-021-11
1-163-021-11
1-163-021-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
10PF
0.01uF
0.01uF
0.01uF
10%
0.5PF
10%
10%
10%
50V
50V
50V
50V
50V
C6
C7
C8
C9
C10
1-163-235-11
1-163-009-11
1-163-251-11
1-163-037-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
0.001uF
100PF
0.022uF
100PF
5%
10%
5%
10%
5%
50V
50V
50V
25V
50V
C11
C12
C13
C14
C15
1-163-131-00
1-163-233-11
1-164-004-11
1-163-021-11
1-163-231-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
390PF
18PF
0.1uF
0.01uF
15PF
5%
5%
10%
10%
5%
50V
50V
25V
50V
50V
C16
C17
C19
C21
C22
1-164-346-11
1-164-004-11
1-164-346-11
1-163-021-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
1uF
0.1uF
1uF
0.01uF
10uF
C23
C24
C25
C26
C27
1-163-263-11
1-164-346-11
1-164-004-11
1-164-004-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
330PF
1uF
0.1uF
0.1uF
0.022uF
10%
10%
10%
50V
16V
25V
25V
25V
C28
C29
C30
C31
C32
1-163-037-11
1-126-960-11
1-126-960-11
1-126-934-11
1-163-021-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
0.022uF
1uF
1uF
220uF
0.01uF
10%
20%
20%
20%
10%
25V
50V
50V
10V
50V
C33
C34
C35
C36
C37
1-163-021-11
1-163-227-11
1-163-227-11
1-164-005-11
1-126-934-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
10PF
10PF
0.47uF
220uF
10%
0.5PF
0.5PF
20%
50V
50V
50V
25V
10V
C38
C39
C40
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
0.001uF
0.001uF
0.001uF
10%
10%
10%
50V
50V
50V
10%
10%
20%
5%
16V
25V
16V
50V
50V
1-567-390-11 FILTER, CERAMIC (10.7MHz)
1-567-390-11 FILTER, CERAMIC (10.7MHz)
1-781-344-12 FILTER, AM CERAMIC
< CONNECTOR >
CN2
1-566-690-11 PLUG, CONNECTOR (2.5mm) 2P
< TRIMMER >
CT1
CT2
1-141-601-11 CAP, ADJ
1-141-601-11 CAP, ADJ
10PF
10PF
< DIODE >
D1
D2
D3
D4
D5
8-719-076-71
8-719-076-71
8-719-050-69
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
KV1471ETR
KV1471ETR
KV1520N
1SS355TE-17
1SS355TE-17
D6
D7
D10
D11
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
< FERRITE BEAD >
FB1
1-500-445-21 FERRITE, EMI (SMD)
< BPF >
FL1
1-236-711-21 FILTER, BAND PASS
< IC >
IC1
IC2
8-759-662-67 IC TA2149N
8-759-483-40 IC LC72137M-TLM
< JUMPER RESISTOR >
JC1
JC2
JC3
JC6
JC7
– 124 –
1-216-295-00
1-216-295-00
1-216-295-00
1-216-296-00
1-216-296-00
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
TUNER
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
< COIL >
L1
L2
L3
L4
L5
1-419-517-11
1-419-518-11
1-416-991-11
1-411-959-11
1-410-994-22
L6
1-419-465-11 COIL (DET)
Remark
< VIBRATOR >
COIL, AIR-CORE
COIL, AIR-CORE
COIL, AM ANT
COIL, AM OSC
INDUCTOR CHIP 1.2uH
X1
1-781-592-11 VIBRATOR, CRYSTAL (75kHz)
*************************************************************
MISCELLANEOUS
***************
60
61
103
106
118
1-791-523-11
1-791-522-11
1-791-521-11
1-791-520-11
1-791-518-11
WIRE, PARALLEL (FFC) (13 CORE)
WIRE, PARALLEL (FFC) (10 CORE)
WIRE, PARALLEL (FFC) (10 CORE)
WIRE, PARALLEL (FFC) (18 CORE)
WIRE, PARALLEL (FFC) (16 CORE)
154
155
156
* 258
0 260
1-791-519-11
1-791-531-21
1-791-532-21
1-667-954-11
A-4672-541-A
WIRE, PARALLEL (FFC) (26 CORE)
WIRE, PARALLEL (FFC) (21 CORE)
WIRE, PARALLEL (FFC) (23 CORE)
FLEXIBLE BOARD
PICK-UP, OPTICAL KMS-260B
< RESISTOR >
R1
R2
R3
R4
R5
1-216-097-11
1-216-065-11
1-216-077-11
1-216-009-11
1-216-073-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
100K
4.7K
15K
22
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R6
R7
R9
R16
R17
1-216-105-11
1-216-081-00
1-216-037-00
1-216-033-00
1-216-033-00
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
220K
22K
330
220
220
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R18
R19
R20
R21
R22
1-216-017-11
1-216-061-00
1-216-049-11
1-216-073-00
1-216-065-11
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
47
3.3K
1K
10K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R23
R25
R26
R27
R28
1-216-295-00
1-216-073-00
1-216-049-11
1-216-049-11
1-216-065-11
SHORT
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0
10K
1K
1K
4.7K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
R29
R30
R31
R32
R33
1-216-025-11
1-216-057-00
1-216-049-11
1-216-021-00
1-216-027-00
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
100
2.2K
1K
68
120
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R34
R35
R36
R67
R70
1-216-021-00
1-216-021-00
1-216-057-00
1-216-065-11
1-216-025-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
68
68
2.2K
4.7K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R71
R73
R74
R75
R76
1-216-025-11
1-216-025-11
1-216-025-11
1-216-025-11
1-216-025-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R96
1-216-073-00 METAL CHIP
10K
5%
1/10W
< TRANSFORMER >
T1
Description
273
0 303
304
ANT1
0 F901
0 F902
0 F903
HR901
M102
M103
M702
S102
S402
SP101
A-4672-475-A MOTOR ASSY, SPINDLE (SPINDLE)
(INCLUDING M101)
8-848-483-05 PICK-UP, OPTICAL KSS-213C (CD)
X-2626-202-1 CHASSIS ASSY, MOTOR (MB) (SPINDLE)
(INCLUDING M701)
1-501-452-11 ANTENNA, TELESCOPIC
1-576-099-11
1-576-105-11
1-576-107-11
1-500-502-11
A-4672-474-A
FUSE (0.8A/250V)
FUSE (2.5A/250V)
FUSE (3.15A/250V)
HEAD, OVER WRITE
MOTOR ASSY, SLED (SLED) (MD)
X-4949-264-1 MOTOR ASSY, LOADING (LOADING)
X-2625-769-1 GEAR ASSY, MOTOR (MB) (RP) (SLED)
1-762-148-21 SWITCH, PUSH (2 KEY) (REFLECT RATE
DETECT, PROTECT DETECT)
1-692-960-11 SWITCH, PUSH (1 KEY) (CD DOOR)
1-529-463-11 SPEAKER (8cm)
SP201 1-529-463-11 SPEAKER (8cm)
0 T901
1-435-320-11 TRANSFORMER, POWER
*************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
0
1-754-102-21
1-783-878-11
3-027-153-11
3-231-405-11
3-867-609-11
ANTENNA, LOOP (AM)
CORD, POWER (7A/125V)
LID, BATTERY CASE (for RMT-CM35A)
MANUAL, INSTRUCTION (FRENCH) (CANADIAN)
MANUAL, INSTRUCTION (ENGLISH) (US)
3-867-609-91 MANUAL, INSTRUCTION
(TRADITIONAL CHINESE) (TAIWAN)
A-3258-025-A REMOTE CONTROLLER (RMT-CM35A)
*************************************************************
1-433-741-11 TRANSFORMER, IF
< TERMINAL >
TB1
1-694-156-11 TERMINAL BOARD (AM ANTENNA)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
– 125 –
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
Ref. No.
Part No.
Description
Remark
**************
HARDWARE LIST
**************
#1
#2
#3
#4
#5
7-685-649-79
7-685-648-79
7-685-647-79
7-685-533-19
7-621-770-87
SCREW +BVTP 3X14 TYPE2 N-S
SCREW +BVTP 3X12 TYPE2 N-S
SCREW +BVTP 3X10 TYPE2 N-S
SCREW +BTP 2.6X6 TYPE2 N-S
SCREW +P 2.6X5
#6
#7
#8
#9
#10
7-685-133-19
7-682-549-04
7-621-772-20
7-621-772-40
7-627-852-08
SCREW (DIA. 2.6) (IT3B)
SCREW +B 3X10
SCREW +B 2X5
SCREW +B 2X8
SCREW, PRECISION +P 1.7X2.5
#11
7-685-661-79 SCREW +BVTP 4X12 TYPE2 N-S
– 126 –
ZS-M35
US Model
Canadian Model
Taiwan Model
SERVICE MANUAL
Ver 1.2 2001.07
SUPPLEMENT-1
File this supplement with the service manual.
Subject : Change of PC Boards
(ECN-RCA01727, RCA01728)
Printed wiring board and schematic diagram of new type, and changed parts list
are described in this Supplement-1.
When performing service and inspection, check the suffix of the part number of
the MAIN, FL, JACK, TOP, LED, POWER, BATT (+) and BATT (–) boards.
– MAIN BOARD (component side) –
MAIN Board Part No.
Former type : 1-675-212-13
New type : 1-675-212-14
ZS-M35
– FL BOARD (component side) –
FL Board Part No.
Former type : 1-675-218-21
New type : 1-675-218-32
– JACK BOARD (component side) –
JACK Board Part No.
Former type : 1-675-219-21
New type : 1-675-219-32
– TOP BOARD (component side) –
– LED BOARD (component side) –
LED Board Part No.
Former type : 1-675-217-21
New type : 1-675-217-32
2
TOP Board Part No.
Former type : 1-675-213-13
New type : 1-675-213-14
ZS-M35
1. Common Note on Schematic Diagram and Printed Wiring Boards
– POWER BOARD (component side) –
Common Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
f
: internal component.
•
• C : panel designation.
POWER Board Part No.
Former type : 1-675-216-21
New type : 1-675-216-32
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
•
•
•
•
•
•
•
•
•
– BATT (+) BOARD (component side) –
BATT (+) Board Part No.
Former type : 1-675-220-21
New type : 1-675-220-32
– BATT (–) BOARD (component side) –
A : B+ Line.
B : B– Line.
H : adjustment for repair.
Voltage and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
: Impossible to measure
∗
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
Circled numbers refer to waveforms.
Signal path.
F : FM
f : AM
E : MD PB
q : MD REC (DIGITAL)
j : MD REC (ANALOG)
J : CD
(
) : Page of service manual
((
)) : Page of service manual supplement-1
BATT (–) Board Part No.
Former type : 1-675-221-21
New type : 1-675-221-32
3
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
3
Common Note on Printed Wiring Boards:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
•
x
: parts mounted on the conductor side.
a
: Through hole.
•
• b : Pattern from the side which enables seeing.
ZS-M35
2. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 3 for Note.
1
2
3
4
5
6
7
8
(Page 57)
9
10
11
12
13
(Page 57)
A
B
((Page 8))
((Page 12))
C
D
((Page 12))
(Page 60)
E
(Page 57)
F
G
((Page 8))
(Page 84)
(Page 73)
H
((Page 10))
I
((Page 10))
J
((Page 8))
4
4
• (
((
) : Page of service manual
)) : Page of service manual supplement-1
ZS-M35
3. SCHEMATIC DIAMGRAM — MAIN SECTION (1/3) — • Refer to page 3 for Note.
((Page 9))
((Page 7))
((Page 6))
((Page 7))
((Page 6))
((Page 9))
((Page 7))
((Page 6))
• Semiconductor Location
Ref. No.
D301
D303
D304
D401
D402
D403
D404
D405
D406
Location
E-5
E-4
D-4
D-9
D-9
B-7
D-8
J-10
J-11
IC301
B-6
Ref. No.
IC302
IC303
IC305
IC401
IC402
IC403
IC404
IC411
Location
F-5
G-5
D-4
G-8
F-9
F-9
B-8
F-12
Q101
Q102
B-5
D-3
Ref. No.
Q103
Q104
Q105
Q106
Q111
Q201
Q202
Q203
Q204
Q205
Q206
Location
F-3
C-3
F-4
C-5
G-3
B-5
D-5
F-3
D-3
F-4
C-5
Ref. No.
Q211
Q301
Q304
Q305
Q306
Q307
Q308
Q309
Q310
Q311
Q312
Location
G-3
D-3
D-3
C-6
D-3
E-3
D-5
E-3
E-7
E-3
F-4
Ref. No.
Q313
Q401
Q402
Q403
Q405
Q406
Q407
Q408
Q409
Q411
Q412
Location
E-4
H-8
B-9
B-8
C-8
J-11
B-9
E-9
H-6
C-8
D-8
5
Ref. No.
Q415
Q416
Q419
Q420
Q421
Q422
Location
I-10
B-9
J-12
J-12
J-10
J-9
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
• ((
)) : Page of service manual supplement-1
5
ZS-M35
4. SCHEMATIC DIAMGRAM — MAIN SECTION (2/3) — • Refer to page 3 for Note.
((Page 7))
((Page 11))
((Page 9))
((Page 11))
((Page 5))
(Page 72)
(Page 85)
((Page 5))
(Page 56)
((Page 7))
((Page 5))
6
6
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
(
) : MD STOP
<
> : CD STOP
• (
((
) : Page of service manual
)) : Page of service manual supplement-1
ZS-M35
((Page 6))
5. SCHEMATIC DIAMGRAM — MAIN SECTION (3/3) — • Refer to page 3 for Note.
(Page 62)
((Page 5))
(Page 56)
(Page 56)
((Page 5))
((Page 13))
((Page 6))
((Page 13))
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
• (
) : Page of service manual
((
)) : Page of service manual supplement-1
7
7
ZS-M35
6. PRINTED WIRING BOARDS — PANEL SECTION — • Refer to page 3 for Note.
1
2
3
4
5
6
7
8
9
10
A
11
12
13
14
((Page 4))
FL401
FLUORESCENT INDICATOR TUBE
B
((Page 4))
C
((Page 4))
D
E
• ((
• Semiconductor
Location
)) : Page of service manual supplement-1
8
8
Ref. No.
D301
D302
D303
D304
Location
B-12
B-12
C-11
C-11
IC601
C-5
Q612
Q613
C-3
C-3
ZS-M35
7. SCHEMATIC DIAMGRAMS — PANEL SECTION — • Refer to page 3 for Note.
((Page 5))
((Page 5))
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
• ((
)) : Page of service manual supplement-1
9
9
((Page 6))
ZS-M35
8. PRINTED WIRING BOARDS — SWITCH SECTION — • Refer to page 3 for Note.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
14
(14)
C
((Page 4))
D
E
((Page 4))
F
abc
G
H
HIGH SPEED
I
• Semiconductor Location
• ((
)) : Page of service manual supplement-1
Ref. No.
D601
D602
D603
D604
D605
D606
D607
D608
D609
10
Location
H-13
H-11
H-10
H-9
H-8
H-7
H-6
G-6
G-7
10
Ref. No.
D610
D611
D612
D613
D614
D615
D616
D617
D618
Location
G-6
G-5
G-4
G-2
H-6
H-5
H-3
H-2
H-5
Ref. No.
D619
D620
D621
D622
D623
D624
D625
Location
H-4
H-3
H-2
I-5
I-4
I-3
I-2
IC602
I-13
Ref. No.
Q603
Q604
Q606
Q607
Q608
Q609
Q610
Q611
Location
H-13
G-12
H-5
G-7
H-3
H-4
I-5
I-5
ZS-M35
9. SCHEMATIC DIAGRAMS — SWITCH SECTION — • Refer to page 3 for Note.
((Page 6))
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
• ((
)) : Page of service manual supplement-1
((Page 6))
11
11
ZS-M35
10. PRINTED WIRING BOARDS — POWER SUPPLY SECTION — • Refer to page 3 for Note.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
J901
AC IN
• Semiconductor Location
Ref. No.
D901
D902
D903
D904
D905
D906
D907
D908
D909
B
C
Location
H-6
H-7
H-6
H-7
H-5
H-5
H-5
H-6
H-3
Ref. No.
D910
D911
D912
D913
D914
D915
Location
I-4
H-3
H-4
H-6
G-7
H-5
Q901
Q902
J-6
I-4
T901
POWER TRANSFORMER
D
7
5
8
E
9
DRY BATTERY
SIZE "AA"
(IEC DESIGNATION R6)
3PCS, 4.5V
MEMORY
BACK-UP
4
10
11
F
2
12
13
1
14
G
BLK
15
H
32
I
32
1-675-221-
(32)
(32)
BLK
BLK/WHT
1-675-220-
1
2
CN904
32
1-675-216-
J
3
2
MAIN BOARD
CN402
MAIN BOARD
CN401
((Page 4))
((Page 4))
(32)
• ((
12
12
)) : Page of service manual supplement-1
ZS-M35
11. SCHEMATIC DIAGRAMS — POWER SUPPLY SECTION — • Refer to page 3 for Note.
((Page 7))
((Page 7))
Note:
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part
number specified.
Note:
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce por tant le numéro
spécifié.
• Voltage is dc with respect to ground under no-signal
(detuned) condition.
no mark : FM
• ((
)) : Page of service manual supplement-1
13
13
ZS-M35
BATT (+)
BATT (–)
FL
JACK
LED
12. ELECTRICAL PARTS LIST
Ref. No.
Part No.
NOTE:
*
*
A-3062-399-A LED BOARD, COMPLETE (ORANGE)
A-3322-633-A LED BOARD, COMPLETE (GREEN)
********************
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
Ref. No.
Part No.
*
1-675-220-32 BATT (+) BOARD
**************
• CAPACITORS
uF : µF
• COILS
uH : µH
Description
Remark
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Part No.
C611
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
Description
3-039-967-01 TERMINAL (–), BATTERY
*************************************************************
* CN602
R601
R602
R605
R606
R609
D601
D602
Remark
D602
D603
8-729-027-44 TRANSISTOR DTC114TKA-T146
8-729-027-44 TRANSISTOR DTC114TKA-T146
3-039-967-01 TERMINAL (–), BATTERY
*************************************************************
A-3322-656-A FL BOARD, COMPLETE
*******************
*
D603
< CAPACITOR >
1-126-964-11
1-163-021-11
1-163-133-00
1-126-947-11
1-107-682-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
10K
47
10K
47
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
1-675-219-32 JACK BOARD
***********
*
10uF
0.01uF
470PF
47uF
1uF
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
R610
1-216-049-11 RES-CHIP
1K
5%
1/10W
R611
1-216-049-11 RES-CHIP
1K
5%
1/10W
R612
1-216-041-00 METAL CHIP
470
5%
1/10W
R613
1-216-049-11 RES-CHIP
1K
5%
1/10W
*************************************************************
3-039-978-01 HOLDER (FL)
3-042-764-01 SHEET (FL), ADHESIVE
3-846-312-01 SPACER
C601
C602
C603
C604
C605
1-216-073-00
1-216-017-11
1-216-073-00
1-216-017-11
1-216-041-00
20%
10%
5%
20%
10%
50V
50V
50V
10V
16V
1-573-455-11 PLUG, CONNECTOR 4P
< DIODE >
C606
C607
C608
C609
C614
1-163-021-11
1-163-009-11
1-163-243-11
1-163-251-11
1-163-259-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.001uF
47PF
100PF
220PF
10%
10%
5%
5%
5%
50V
50V
50V
50V
50V
C621
C622
C623
C624
C625
1-163-259-11
1-164-005-11
1-164-005-11
1-164-005-11
1-164-005-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
220PF
0.47uF
0.47uF
0.47uF
0.47uF
5%
50V
25V
25V
25V
25V
< CONNECTOR >
CN601
1-695-371-31 CONNECTOR, FFC/FPC 10P
D301
D302
D303
D304
1-517-916-12 INDICATOR TUBE, FLUORESCENT
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
< FERRITE BEAD >
FB101
FB102
FB201
FB202
FB301
1-216-295-11
1-469-152-11
1-216-295-11
1-469-152-11
1-216-295-11
FB302
1-469-152-11 FERRITE, EMI (SMD)
< FLUORESCENT INDICATOR >
FL401
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
SHORT
0
FERRITE, EMI (SMD)
SHORT
0
FERRITE, EMI (SMD)
SHORT
0
< JACK >
J301
J302
20%
25V
1-695-374-31 PIN, CONNECTOR (PC BOARD) 13P
D604
8-719-077-79 LED SLR-332VRT32 (HIGH SPEED)
8-719-078-08 LED SLA-362MT-T31XFG (DELETE/CLOCK)
(GREEN)
8-719-078-09 LED SLR-332DC-T32MN (DELETE/CLOCK)
(ORANGE)
8-719-078-08 LED SLA-362MT-T31XFG (INSERT/TIMER)
(GREEN)
8-719-078-09 LED SLR-332DC-T32MN (INSERT/TIMER)
(ORANGE)
D606
8-719-078-08 LED SLA-362MT-T31XFG (NO/CANCEL)
(GREEN)
8-719-078-09 LED SLR-332DC-T32MN (NO/CANCEL)
(ORANGE)
8-719-078-08 LED SLA-362MT-T31XFG (YES/ENTER)
(GREEN)
8-719-078-09 LED SLR-332DC-T32MN (YES/ENTER)
(ORANGE)
8-719-078-08 LED SLA-362MT-T31XFG (DISPLAY) (GREEN)
D606
D607
D607
D608
D609
8-719-078-09
8-719-078-08
8-719-078-09
8-719-077-79
8-719-077-79
LED
LED
LED
LED
LED
SLR-332DC-T32MN (DISPLAY) (ORANGE)
SLA-362MT-T31XFG (4/GHI) (GREEN)
SLR-332DC-T32MN (4/GHI) (ORANGE)
SLR-332VRT32 (abc)
SLR-332VRT32 (ABC)
D610
D610
D611
D611
D612
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
LED
LED
LED
LED
LED
SLA-362MT-T31XFG (1) (GREEN)
SLR-332DC-T32MN (1) (ORANGE)
SLA-362MT-T31XFG (1) (GREEN)
SLR-332DC-T32MN (1) (ORANGE)
SLA-362MT-T31XFG (2/ABC) (GREEN)
D612
D613
D613
D614
D614
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
LED
LED
LED
LED
LED
SLR-332DC-T32MN (2/ABC) (ORANGE)
SLA-362MT-T31XFG (3/DEF) (GREEN)
SLR-332DC-T32MN (3/DEF) (ORANGE)
SLA-362MT-T31XFG (DISPLAY) (GREEN)
SLR-332DC-T32MN (DISPLAY) (ORANGE)
D615
D615
D616
D616
D617
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
LED
LED
LED
LED
LED
SLA-362MT-T31XFG (4/GHI) (GREEN)
SLR-332DC-T32MN (4/GHI) (ORANGE)
SLA-362MT-T31XFG (5/JKL) (GREEN)
SLR-332DC-T32MN (5/JKL) (ORANGE)
SLA-362MT-T31XFG (6/MNO) (GREEN)
D617
D618
D618
D619
D619
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
LED
LED
LED
LED
LED
SLR-332DC-T32MN (6/MNO) (ORANGE)
SLA-362MT-T31XFG (7/PQRS) (GREEN)
SLR-332DC-T32MN (7/PQRS) (ORANGE)
SLA-362MT-T31XFG (7/PQRS) (GREEN)
SLR-332DC-T32MN (7/PQRS) (ORANGE)
D604
D605
D605
Ref. No.
Part No.
Description
D620
D620
D621
D621
D622
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
LED
LED
LED
LED
LED
SLA-362MT-T31XFG (8/TUV) (GREEN)
SLR-332DC-T32MN (8/TUV) (ORANGE)
SLA-362MT-T31XFG (9/WXYZ) (GREEN)
SLR-332DC-T32MN (9/WXYZ) (ORANGE)
SLA-362MT-T31XFG (SYMBOL) (GREEN)
D622
D623
D623
D624
D624
8-719-078-09
8-719-078-08
8-719-078-09
8-719-078-08
8-719-078-09
LED
LED
LED
LED
LED
SLR-332DC-T32MN (SYMBOL) (ORANGE)
SLA-362MT-T31XFG (SYMBOL) (GREEN)
SLR-332DC-T32MN (SYMBOL) (ORANGE)
SLA-362MT-T31XFG (0/10) (GREEN)
SLR-332DC-T32MN (0/10) (ORANGE)
D625
8-719-078-08 LED SLA-362MT-T31XFG (>10 AM/PM)
(GREEN)
8-719-078-09 LED SLR-332DC-T32MN (>10 AM/PM)
(ORANGE)
D625
Remark
< IC >
IC602
8-749-016-97 IC NJL62H400A
< JUMPER RESISTOR >
JC601
JC603
JC604
1-216-295-11 SHORT
1-216-295-11 SHORT
1-216-295-11 SHORT
0
0
0
< TRANSISTOR >
Q603
Q604
Q606
Q607
Q608
8-729-027-58
8-729-901-88
8-729-027-58
8-729-027-58
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC143ZKA-T146
2SC2411K-CR
DTC143ZKA-T146
DTC143ZKA-T146
2SC1623-L5L6
Q609
Q610
Q611
8-729-120-28 TRANSISTOR 2SC1623-L5L6
8-729-120-28 TRANSISTOR 2SC1623-L5L6
8-729-120-28 TRANSISTOR 2SC1623-L5L6
< RESISTOR >
< CONNECTOR >
* CN306
4.7uF
< DIODE >
< RESISTOR >
1-675-221-32 BATT (–) BOARD
**************
*
1-126-794-11 ELECT
< CONNECTOR >
< TRANSISTOR >
Q612
Q613
Remark
< CAPACITOR >
When indicating parts by reference
number, please include the board.
Ref. No.
Description
1-566-891-11 JACK (i)
1-566-891-11 JACK (LINE IN)
R603
1-216-025-11 RES-CHIP
100
5%
R603
1-216-033-00 METAL CHIP
220
5%
R614
R615
R617
1-216-085-91 RES-CHIP
1-216-033-00 METAL CHIP
1-216-025-11 RES-CHIP
33K
220
100
5%
5%
5%
R617
1-216-033-00 METAL CHIP
220
5%
R620
1-216-025-11 RES-CHIP
100
5%
R620
1-216-033-00 METAL CHIP
220
5%
R622
R624
1-216-051-00 METAL CHIP
1-216-033-00 METAL CHIP
1.2K
220
5%
5%
R626
R628
1-216-033-00 METAL CHIP
1-216-025-11 RES-CHIP
220
100
5%
5%
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
1/10W
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
1/10W
1/10W
1/10W
(GREEN)
< IC >
< RESISTOR >
IC601
NOTE: There are two different colors of LEDs on the LED board.
In service, check the color of the set before replacing parts.
Color of the set
Color of LEDs
BLACK ..................... GREEN
WHITE ...................... GREEN
BLUE ........................ GREEN
ORANGE .................. ORANGE
8-759-663-70 IC ML9206-03MBZ060
R103
1-216-033-00 METAL CHIP
220
5%
1/10W
R203
1-216-033-00 METAL CHIP
220
5%
1/10W
*************************************************************
14
14
ZS-M35
LED
Ref. No.
Part No.
Description
Remark
R628
1-216-033-00 METAL CHIP
220
5%
R631
1-216-174-00 RES-CHIP
100
5%
R631
1-216-182-00 RES-CHIP
220
5%
R633
1-216-025-11 RES-CHIP
100
5%
R633
1-216-033-00 METAL CHIP
220
5%
R636
1-216-025-11 RES-CHIP
100
5%
R636
1-216-033-00 METAL CHIP
220
5%
R638
1-216-025-11 RES-CHIP
100
5%
R638
1-216-033-00 METAL CHIP
220
5%
R641
1-216-025-11 RES-CHIP
100
5%
R641
1-216-033-00 METAL CHIP
220
5%
R643
1-216-025-11 RES-CHIP
100
5%
R643
1-216-033-00 METAL CHIP
220
5%
R646
1-216-025-11 RES-CHIP
100
5%
R646
1-216-033-00 METAL CHIP
220
5%
R648
R649
R650
R651
R666
1-216-045-00
1-216-048-00
1-216-056-00
1-216-061-91
1-216-025-11
680
910
2K
3.3K
100
5%
5%
5%
5%
5%
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
R666
1-216-033-00 METAL CHIP
220
5%
R667
1-216-025-11 RES-CHIP
100
5%
R667
1-216-033-00 METAL CHIP
220
5%
R668
1-216-025-11 RES-CHIP
100
5%
R668
1-216-033-00 METAL CHIP
220
5%
R670
1-216-025-11 RES-CHIP
100
5%
R670
1-216-033-00 METAL CHIP
220
5%
R671
1-216-025-11 RES-CHIP
100
5%
R671
1-216-033-00 METAL CHIP
220
5%
R672
1-216-025-11 RES-CHIP
100
5%
Ref. No.
1/10W
(ORANGE)
1/8W
(GREEN)
1/8W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
Part No.
Description
MAIN
Remark
R672
1-216-033-00 METAL CHIP
220
5%
R673
1-216-025-11 RES-CHIP
100
5%
R673
1-216-033-00 METAL CHIP
220
5%
R674
1-216-025-11 RES-CHIP
100
5%
R674
1-216-033-00 METAL CHIP
220
5%
R675
1-216-025-11 RES-CHIP
100
5%
R675
1-216-033-00 METAL CHIP
220
5%
R676
1-216-025-11 RES-CHIP
100
5%
R676
1-216-033-00 METAL CHIP
220
5%
R677
1-216-025-11 RES-CHIP
100
5%
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
R677
1-216-033-00 METAL CHIP
220
5%
S601
S601
S602
S602
S603
1-554-937-11
1-692-014-11
1-554-937-11
1-692-014-11
1-554-937-11
1/10W
1/10W
1/10W
1/10W
1/10W
(GREEN)
S603
S604
1-692-014-11 SWITCH, KEYBOARD (STANDBY) (GREEN)
1-554-937-11 SWITCH, KEYBOARD (AUTO PRESET/SHUF/PGM)
(ORANGE)
1-692-014-11 SWITCH, KEYBOARD (AUTO PRESET/SHUF/PGM)
(GREEN)
1-554-937-11 SWITCH, KEYBOARD (MONO/ST/REPEAT)
(ORANGE)
1-692-014-11 SWITCH, KEYBOARD (MONO/ST/REPEAT)
(GREEN)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
1/10W
(GREEN)
1/10W
(ORANGE)
< SWITCH >
S604
S605
S605
SWITCH, KEYBOARD (POWER) (ORANGE)
SWITCH, KEYBOARD (POWER) (GREEN)
SWITCH, KEYBOARD (SLEEP) (ORANGE)
SWITCH, KEYBOARD (SLEEP) (GREEN)
SWITCH, KEYBOARD (STANDBY) (ORANGE)
S606
1-554-937-11 SWITCH, KEYBOARD (EDIT) (ORANGE)
S606
1-692-014-11 SWITCH, KEYBOARD (EDIT) (GREEN)
*************************************************************
A-3322-636-A MAIN BOARD, COMPLETE
*********************
*
3-039-961-01 SPRING (IC)
3-831-441-99 CUSHION (A)
7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
< CAPACITOR >
C101
C102
C103
C104
C105
1-126-767-11
1-126-963-11
1-126-963-11
1-163-251-11
1-163-021-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
C106
1-136-165-00 MYLAR
1000uF
4.7uF
4.7uF
100PF
0.01uF
20%
20%
20%
5%
10%
16V
50V
50V
50V
50V
0.1uF
5%
50V
NOTE: There are two different colors of LEDs on the LED board.
In service, check the color of the set before replacing parts.
Color of the set
Color of LEDs
BLACK ..................... GREEN
WHITE ...................... GREEN
BLUE ........................ GREEN
ORANGE .................. ORANGE
15
ZS-M35
MAIN
Ref. No.
Part No.
Description
Part No.
Description
C107
C108
C109
C110
C111
1-136-165-00
1-126-960-11
1-126-964-11
1-126-961-11
1-126-961-11
MYLAR
ELECT
ELECT
ELECT
ELECT
0.1uF
1uF
10uF
2.2uF
2.2uF
5%
20%
20%
20%
20%
50V
50V
50V
50V
50V
C318
C319
C320
C321
C322
1-126-964-11
1-126-960-11
1-163-009-11
1-163-009-11
1-126-964-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
10uF
1uF
0.001uF
0.001uF
10uF
20%
20%
10%
10%
20%
50V
50V
50V
50V
50V
C112
C113
C114
C115
C116
1-126-961-11
1-126-961-11
1-136-157-00
1-136-173-00
1-136-153-00
ELECT
ELECT
MYLAR
MYLAR
FILM
2.2uF
2.2uF
0.022uF
0.47uF
0.01uF
20%
20%
5%
5%
5%
50V
50V
50V
50V
50V
C323
C324
C326
C401
C402
1-104-665-11
1-104-665-11
1-126-964-11
1-163-237-11
1-163-104-00
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
100uF
100uF
10uF
27PF
30PF
20%
20%
20%
5%
5%
10V
10V
50V
50V
50V
C117
C118
C119
C126
C127
1-126-963-11
1-126-961-11
1-126-960-11
1-126-960-11
1-163-009-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
4.7uF
2.2uF
1uF
1uF
0.001uF
20%
20%
20%
20%
10%
50V
50V
50V
50V
50V
C403
C404
C405
C406
C407
1-164-346-11
1-163-239-11
1-163-239-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
33PF
33PF
0.001uF
0.001uF
5%
5%
10%
10%
16V
50V
50V
50V
50V
C128
C201
C202
C203
C204
1-163-251-11
1-126-767-11
1-126-963-11
1-126-963-11
1-163-251-11
CERAMIC CHIP
ELECT
ELECT
ELECT
CERAMIC CHIP
100PF
1000uF
4.7uF
4.7uF
100PF
5%
20%
20%
20%
5%
50V
16V
50V
50V
50V
C408
C409
C410
C411
C412
1-163-235-11
1-163-234-11
1-107-725-11
1-104-665-11
1-164-346-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
22PF
20PF
0.1uF
100uF
1uF
5%
5%
10%
20%
50V
50V
16V
10V
16V
C205
C206
C207
C208
C209
1-163-021-11
1-136-165-00
1-136-165-00
1-126-960-11
1-126-964-11
CERAMIC CHIP
MYLAR
MYLAR
ELECT
ELECT
0.01uF
0.1uF
0.1uF
1uF
10uF
10%
5%
5%
20%
20%
50V
50V
50V
50V
50V
C413
C414
C416
C417
C418
1-126-947-11
1-126-964-11
1-126-919-11
1-163-009-11
1-164-346-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
47uF
10uF
6800uF
0.001uF
1uF
20%
20%
20%
10%
10V
50V
6.3V
50V
16V
C210
C211
C212
C213
C214
1-126-961-11
1-126-961-11
1-126-961-11
1-126-961-11
1-136-157-00
ELECT
ELECT
ELECT
ELECT
MYLAR
2.2uF
2.2uF
2.2uF
2.2uF
0.022uF
20%
20%
20%
20%
5%
50V
50V
50V
50V
50V
C419
C420
C421
C422
C423
1-163-021-11
1-126-933-11
1-107-725-11
1-126-935-11
1-163-021-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
0.01uF
100uF
0.1uF
470uF
0.01uF
10%
20%
10%
20%
10%
50V
16V
16V
10V
50V
C215
C216
C217
C218
C219
1-136-173-00
1-136-153-00
1-126-963-11
1-126-961-11
1-126-960-11
MYLAR
FILM
ELECT
ELECT
ELECT
0.47uF
0.01uF
4.7uF
2.2uF
1uF
5%
5%
20%
20%
20%
50V
50V
50V
50V
50V
C424
C425
C428
C430
C431
1-163-021-11
1-126-934-11
1-126-947-11
1-163-021-11
1-126-934-11
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
ELECT
0.01uF
220uF
47uF
0.01uF
220uF
10%
20%
20%
10%
20%
50V
10V
10V
50V
10V
C226
C227
C228
C301
C302
1-126-960-11
1-163-009-11
1-163-251-11
1-104-665-11
1-126-963-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
1uF
0.001uF
100PF
100uF
4.7uF
20%
10%
5%
20%
20%
50V
50V
50V
10V
50V
C433
C434
C435
C436
C437
1-163-021-11
1-126-964-11
1-163-021-11
1-163-021-11
1-126-964-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
10uF
0.01uF
0.01uF
10uF
10%
20%
10%
10%
20%
50V
50V
50V
50V
50V
C303
C306
C307
C308
C309
1-115-877-11
1-126-964-11
1-163-009-11
1-104-665-11
1-126-934-11
DOUBLE LAYERS
ELECT
CERAMIC CHIP
ELECT
ELECT
4700uF
10uF
0.001uF
100uF
220uF
20%
20%
10%
20%
20%
25V
50V
50V
10V
10V
C438
C439
C440
C441
C443
1-163-021-11
1-126-968-11
1-126-960-11
1-126-960-11
1-126-937-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.01uF
100uF
1uF
1uF
4700uF
10%
20%
20%
20%
20%
50V
50V
50V
50V
16V
C310
C311
C312
C313
C314
1-104-665-11
1-104-665-11
1-104-665-11
1-126-964-11
1-163-021-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
100uF
100uF
100uF
10uF
0.01uF
20%
20%
20%
20%
10%
10V
10V
10V
50V
50V
C444
C445
C446
C447
C450
1-163-009-11
1-164-161-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.0022uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
100V
50V
50V
50V
C315
C316
C317
1-163-021-11 CERAMIC CHIP
1-104-665-11 ELECT
1-107-725-11 CERAMIC CHIP
0.01uF
100uF
0.1uF
10%
20%
10%
50V
10V
16V
C451
C452
C453
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
0.001uF
0.001uF
0.001uF
10%
10%
10%
50V
50V
50V
16
Remark
Ref. No.
Remark
ZS-M35
MAIN
Ref. No.
Part No.
Description
Part No.
Description
C454
C455
C456
C457
C458
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
Remark
Ref. No.
C514
C515
C528
C529
C531
1-163-009-11
1-163-021-11
1-104-665-11
1-163-021-11
1-126-933-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.001uF
0.01uF
100uF
0.01uF
100uF
10%
10%
20%
10%
20%
50V
50V
10V
50V
16V
Remark
C459
C460
C461
C462
C463
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C532
C533
C535
C536
C537
1-126-933-11
1-163-021-11
1-163-009-11
1-163-009-11
1-163-009-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100uF
0.01uF
0.001uF
0.001uF
0.001uF
20%
10%
10%
10%
10%
16V
50V
50V
50V
50V
C464
C465
C466
C468
C469
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C538
C539
C540
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
0.001uF
0.001uF
0.001uF
10%
10%
10%
50V
50V
50V
C470
C472
C473
C474
C477
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
100PF
10%
10%
10%
10%
5%
50V
50V
50V
50V
50V
*
*
*
*
*
CN301
CN303
CN401
CN402
CN403
1-564-778-11
1-785-656-11
1-564-778-11
1-785-662-11
1-568-468-11
PLUG, CONNECTOR (2.5mm) 4P
PIN, CONNECTOR (PC BOARD) 4P
PLUG, CONNECTOR (2.5mm) 4P
PIN, CONNECTOR (PC BOARD) 10P
PIN, CONNECTOR (PC BOARD) 18P
C478
C479
C480
C481
C482
1-163-243-11
1-163-009-11
1-163-021-11
1-126-964-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
47PF
0.001uF
0.01uF
10uF
10uF
5%
10%
10%
20%
20%
50V
50V
50V
50V
50V
CN404
* CN405
CN406
* CN407
* CN408
1-568-931-11
1-695-333-41
1-695-336-31
1-695-333-41
1-785-661-11
PIN, CONNECTOR (PC BOARD) 26P
PIN, CONNECTOR (PC BOARD) 10P
PIN, CONNECTOR (PC BOARD) 13P
PIN, CONNECTOR (PC BOARD) 10P
PIN, CONNECTOR (PC BOARD) 9P
C483
C484
C485
C486
C487
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
* CN409
* CN410
* CN416
CN450
1-785-655-11
1-785-654-11
1-566-690-11
1-566-690-11
PIN, CONNECTOR (PC BOARD) 3P
PIN, CONNECTOR (PC BOARD) 2P
PLUG, CONNECTOR (2.5mm) 2P
PLUG, CONNECTOR (2.5mm) 2P
C488
C489
C490
C491
C492
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C493
C494
C495
C496
C497
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
0.001uF
0.001uF
0.001uF
10%
10%
10%
10%
10%
50V
50V
50V
50V
50V
C498
C499
C500
C502
C503
1-163-251-11
1-163-251-11
1-163-251-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
100PF
0.001uF
0.001uF
5%
5%
5%
10%
10%
50V
50V
50V
50V
50V
C504
C505
C506
C507
C509
1-163-009-11
1-163-243-11
1-163-009-11
1-163-009-11
1-163-009-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
47PF
0.001uF
0.001uF
0.001uF
10%
5%
10%
10%
10%
50V
50V
50V
50V
50V
C510
C512
C513
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
1-163-009-11 CERAMIC CHIP
0.001uF
0.001uF
0.001uF
10%
10%
10%
50V
50V
50V
< CONNECTOR >
< DIODE >
D301
D303
D304
D401
D402
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
1SS355TE-17
D403
D404
D405
D406
8-719-056-84
8-719-056-85
8-719-056-82
8-719-977-81
DIODE
DIODE
DIODE
DIODE
UDZ-TE-17-7.5B
UDZ-TE-17-8.2B
UDZ-TE-17-6.2B
DTZ33B
< FERRITE BEAD >
FB401
FB402
FB403
FB404
FB405
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
FB406
FB407
FB408
FB409
FB410
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
FB411
1-216-295-11 SHORT
0
17
ZS-M35
MAIN
Ref. No.
Part No.
Description
Part No.
Description
FB412
FB413
FB414
FB415
FB416
1-469-185-11
1-469-185-11
1-216-295-11
1-216-295-11
1-216-295-11
FERRITE BEAD INDUCTOR
FERRITE BEAD INDUCTOR
SHORT
0
SHORT
0
SHORT
0
Remark
Q305
Q306
Q307
Q308
Q309
8-729-027-46
8-729-027-23
8-729-900-53
8-729-120-28
8-729-027-23
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114YKA-T146
DTA114EKA-T146
DTC114EK
2SC1623-L5L6
DTA114EKA-T146
FB417
FB418
FB419
FB420
FB421
1-216-295-11
1-216-296-11
1-216-296-11
1-216-295-11
1-216-295-11
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
Q310
Q311
Q312
Q313
Q401
8-729-027-26
8-729-027-24
8-729-027-24
8-729-027-26
8-729-903-10
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTA114YKA-T146
DTA114TKA-T146
DTA114TKA-T146
DTA114YKA-T146
FMW1
FB423
FB424
FB425
FB426
FB427
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
SHORT
SHORT
SHORT
SHORT
SHORT
0
0
0
0
0
Q402
Q403
Q405
Q406
Q407
8-729-018-99
8-729-021-82
8-729-021-82
8-729-903-46
8-729-027-26
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD2394-F
2SD2396K
2SD2396K
2SB1132-P
DTA114YKA-T146
FB428
FB429
FB430
1-216-073-00 RES-CHIP
1-216-295-11 SHORT
1-216-073-00 RES-CHIP
< IC >
Q408
Q409
Q411
Q412
Q415
8-729-027-46
8-729-027-29
8-729-027-26
8-729-027-46
8-729-027-29
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114YKA-T146
DTA123JKA-T146
DTA114YKA-T146
DTC114YKA-T146
DTA123JKA-T146
Q416
Q419
Q420
Q421
Q422
8-729-027-46
8-729-012-83
8-729-012-83
8-729-027-26
8-729-027-46
TRANSISTOR DTC114YKA-T146
FET 2SK679A
FET 2SK679A
TRANSISTOR DTA114YKA-T146
TRANSISTOR DTC114YKA-T146
10K
0
10K
IC301
IC302
IC303
IC305
IC401
8-759-543-56
8-759-652-74
8-759-100-96
8-759-636-55
8-752-915-75
IC
IC
IC
IC
IC
LA4601N
M62443FPD61Q
NJM4558M-TE2
M5218AFP-T1
CXP740096-044Q
IC402
IC403
IC404
IC411
8-759-486-73
8-759-649-23
8-759-450-47
8-759-486-73
IC
IC
IC
IC
XC62FP3302PR
XC61CN2802PR
BA05T
XC62FP3302PR
5%
1/10W
5%
1/10W
1-216-295-11
1-216-295-11
1-216-295-11
1-216-295-11
Remark
< RESISTOR >
R101
R102
R103
R104
R105
1-216-049-11
1-216-061-00
1-216-025-11
1-216-049-11
1-216-052-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
1K
3.3K
100
1K
1.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< TRANSISTOR >
R106
R107
R108
R109
R110
1-216-111-00
1-216-121-11
1-216-079-00
1-216-073-00
1-216-049-11
METAL CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
390K
1M
18K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
< JUMPER RESISTOR >
JC102
JC103
JC107
JC108
Ref. No.
SHORT
SHORT
SHORT
SHORT
0
0
0
0
Q101
Q102
Q103
Q104
Q105
8-729-027-46
8-729-120-28
8-729-027-46
8-729-920-31
8-729-120-28
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114YKA-T146
2SC1623-L5L6
DTC114YKA-T146
DTC343TK
2SC1623-L5L6
R111
R112
R113
R114
R115
1-216-077-11
1-216-073-00
1-216-689-11
1-216-089-11
1-216-079-00
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
METAL CHIP
15K
10K
39K
47K
18K
5%
5%
0.5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Q106
Q111
Q201
Q202
Q203
8-729-027-46
8-729-920-31
8-729-027-46
8-729-120-28
8-729-027-46
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114YKA-T146
DTC343TK
DTC114YKA-T146
2SC1623-L5L6
DTC114YKA-T146
R116
R117
R118
R119
R120
1-216-113-00
1-216-081-00
1-216-057-00
1-216-047-11
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
470K
22K
2.2K
820
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
Q204
Q205
Q206
Q211
Q301
8-729-920-31
8-729-120-28
8-729-027-46
8-729-920-31
8-729-027-24
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC343TK
2SC1623-L5L6
DTC114YKA-T146
DTC343TK
DTA114TKA-T146
R122
R123
R124
R125
R201
1-216-198-11
1-216-077-11
1-216-049-11
1-216-089-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
15K
1K
47K
1K
5%
5%
5%
5%
5%
1/8W
1/10W
1/10W
1/10W
1/10W
Q304
8-729-900-53 TRANSISTOR DTC114EK
R202
1-216-061-00 RES-CHIP
3.3K
5%
1/10W
18
ZS-M35
MAIN
Ref. No.
Part No.
Description
Part No.
Description
R203
R204
R205
R206
R207
1-216-025-11
1-216-049-11
1-216-052-00
1-216-111-00
1-216-121-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
100
1K
1.3K
390K
1M
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
Ref. No.
R408
R409
R410
R411
R412
1-216-047-11
1-216-047-11
1-216-041-00
1-216-077-11
1-216-025-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
820
820
470
15K
100
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
R208
R209
R210
R211
R212
1-216-079-00
1-216-073-00
1-216-049-11
1-216-077-11
1-216-073-00
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
18K
10K
1K
15K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R413
R416
R417
R418
R419
1-216-053-00
1-216-073-00
1-216-049-11
1-216-049-11
1-216-049-11
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1.5K
10K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R213
R214
R215
R216
R217
1-216-689-11
1-216-089-11
1-216-079-00
1-216-113-00
1-216-081-00
METAL CHIP
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
39K
47K
18K
470K
22K
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R422
R423
R424
R425
R426
1-216-073-00
1-216-049-11
1-216-041-00
1-216-041-00
1-216-049-11
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
RES-CHIP
10K
1K
470
470
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R218
R219
R220
R222
R223
1-216-057-00
1-216-047-11
1-216-061-00
1-216-049-11
1-216-077-11
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
2.2K
820
3.3K
1K
15K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R427
R428
R429
R430
R431
1-216-073-00
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R224
R225
R302
R303
R304
1-216-049-11
1-216-089-11
1-216-073-00
1-216-073-00
1-216-057-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
1K
47K
10K
10K
2.2K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R432
R433
R434
R435
R436
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R306
R307
R308
R309
R310
1-216-025-11
1-216-073-00
1-216-073-00
1-216-166-00
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100
10K
10K
47
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/8W
1/10W
R437
R438
R439
R440
R441
1-216-049-11
1-216-049-11
1-216-113-00
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1K
1K
470K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R311
R312
R313
R314
R315
1-216-049-11
1-216-065-11
1-216-073-00
1-216-073-00
1-216-073-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
4.7K
10K
10K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R442
R443
R444
R445
R446
1-216-085-00
1-216-085-00
1-216-085-00
1-216-085-00
1-216-085-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
33K
33K
33K
33K
33K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R316
R317
R318
R319
R320
1-216-113-00
1-216-049-11
1-216-121-11
1-216-049-11
1-216-049-11
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
470K
1K
1M
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R447
R449
R450
R451
R453
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
1-216-065-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1K
1K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R321
R322
R323
R324
R327
1-216-097-11
1-216-073-00
1-216-041-00
1-216-049-11
1-216-073-00
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
100K
10K
470
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R454
R455
R456
R457
R458
1-216-113-00
1-216-041-00
1-216-041-00
1-216-049-11
1-216-049-11
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
470K
470
470
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R328
R329
R401
R402
R403
1-216-073-00
1-216-025-11
1-216-222-00
1-216-198-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
100
10K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/8W
1/8W
1/10W
R459
R460
R461
R462
R463
1-216-049-11
1-216-065-11
1-216-081-00
1-216-089-11
1-216-049-11
RES-CHIP
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1K
4.7K
22K
47K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R404
R406
R407
1-216-025-11 RES-CHIP
1-216-308-00 METAL CHIP
1-216-017-11 RES-CHIP
100
4.7
47
5%
5%
5%
1/10W
1/10W
1/10W
R464
R465
R466
1-216-049-11 RES-CHIP
1-216-049-11 RES-CHIP
1-216-049-11 RES-CHIP
1K
1K
1K
5%
5%
5%
1/10W
1/10W
1/10W
19
ZS-M35
MAIN
Ref. No.
POWER
Part No.
Description
Remark
Ref. No.
Part No.
R467
R468
R469
R470
R471
1-216-049-11
1-216-049-11
1-216-049-11
1-216-198-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/8W
1/10W
*
A-3322-637-A POWER BOARD, COMPLETE
***********************
R472
R473
R474
R475
R476
1-216-049-11
1-216-190-00
1-216-190-00
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
470
470
1K
1K
5%
5%
5%
5%
5%
1/10W
1/8W
1/8W
1/10W
1/10W
R477
R478
R479
R480
R481
1-216-073-00
1-216-049-11
1-216-049-11
1-216-049-11
1-216-025-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
1K
1K
1K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R482
R483
R484
R485
R486
1-216-049-11
1-216-025-11
1-216-049-11
1-216-065-11
1-216-065-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
100
1K
4.7K
4.7K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R487
R488
R489
R490
R491
1-216-065-11
1-216-041-00
1-216-049-11
1-216-049-11
1-216-049-11
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
4.7K
470
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R492
R493
R494
R496
R497
1-216-049-11
1-216-049-11
1-216-073-00
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
10K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R499
R500
R505
R506
R513
1-216-089-11
1-216-041-00
1-216-085-00
1-216-073-00
1-216-049-11
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
RES-CHIP
47K
470
33K
10K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R520
R521
R522
R523
R524
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
1-216-049-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R525
R527
R528
R529
1-216-049-11
1-216-041-00
1-216-097-11
1-216-097-11
RES-CHIP
METAL CHIP
RES-CHIP
RES-CHIP
1K
470
100K
100K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
Description
Remark
1-533-233-31 HOLDER, FUSE
< CAPACITOR >
C901
C902
C903
C904
C905
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
0.022uF
0.022uF
0.022uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C906
C907
C908
C909
C910
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
0.022uF
0.022uF
0.022uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C911
C912
C913
C914
C915
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
1-163-037-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
0.022uF
0.022uF
0.022uF
0.022uF
10%
10%
10%
10%
10%
25V
25V
25V
25V
25V
C916
C917
C918
C919
0 C920
1-163-037-11
1-163-021-11
1-163-021-11
1-163-021-11
1-113-925-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
0.022uF
0.01uF
0.01uF
0.01uF
0.01uF
10%
10%
10%
10%
20%
25V
50V
50V
50V
250V
0 C922
1-113-925-11 CERAMIC
0.01uF
20%
250V
< CONNECTOR >
* CN903
< VIBRATOR >
X401
1-781-598-21 VIBRATOR, CERAMIC (8MHz)
X402
1-767-697-11 VIBRATOR, CRYSTAL (32kHz)
*************************************************************
1-785-654-11 PIN, CONNECTOR (PC BOARD) 2P
< DIODE >
D901
D902
D903
D904
D905
8-719-046-07
8-719-046-07
8-719-046-07
8-719-046-07
8-719-046-07
DIODE
DIODE
DIODE
DIODE
DIODE
2A02M
2A02M
2A02M
2A02M
2A02M
D906
D907
D908
D909
D910
8-719-046-07
8-719-046-07
8-719-046-07
8-719-063-79
8-719-063-79
DIODE
DIODE
DIODE
DIODE
DIODE
2A02M
2A02M
2A02M
1N4002B
1N4002B
D911
D912
D913
D914
D915
8-719-063-79
8-719-063-79
8-719-988-61
8-719-988-61
8-719-988-61
DIODE
DIODE
DIODE
DIODE
DIODE
1N4002B
1N4002B
1SS355TE-17
1SS355TE-17
1SS355TE-17
< FUSE >
0 F901
0 F902
0 F903
1-576-099-11 FUSE (800mA/250V)
1-576-105-11 FUSE (2.5A/250V)
1-576-107-11 FUSE (3.15A/250V)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
20
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
ZS-M35
POWER
Ref. No.
Part No.
Description
Remark
< AC INLET >
0 J901
Ref. No.
S643
S644
S645
S646
1-540-009-11 INLET, AC (- AC IN)
TOP
Part No.
Description
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
SWITCH, KEYBOARD (CD B X)
SWITCH, KEYBOARD (TUNE > +)
SWITCH, KEYBOARD (TUNE . –)
SWITCH, KEYBOARD (LINE/LINE LEVEL)
Remark
< IC LINK >
0 PS901
1-532-679-00 LINK, IC (ICP-N15) 0.6A
< TRANSISTOR >
Q901
Q902
8-729-027-50 TRANSISTOR DTC123JKA-T146
8-729-120-28 TRANSISTOR 2SC1623-L5L6
< RESISTOR >
R901
R902
R905
R906
1-216-073-00
1-216-089-11
1-216-089-11
1-216-073-00
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
47K
47K
10K
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
< RELAY >
RY901
1-755-363-11 RELAY
< TRANSFORMER >
0 T901
1-435-320-11 TRANSFORMER, POWER
*************************************************************
1-675-213-14 TOP BOARD
**********
*
3-363-898-01 CUSHION
3-831-441-11 CUSHION (B)
< RESISTOR >
R654
R655
R656
R657
R658
1-216-045-00
1-216-048-00
1-216-051-00
1-216-056-00
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
680
910
1.2K
2K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R660
R661
R662
R663
R664
1-216-045-00
1-216-048-00
1-216-051-00
1-216-056-00
1-216-061-00
METAL CHIP
METAL CHIP
METAL CHIP
RES-CHIP
RES-CHIP
680
910
1.2K
2K
3.3K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R665
1-216-069-00 METAL CHIP
6.8K
5%
1/10W
< SWITCH >
S633
S634
S635
S636
S637
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
SWITCH, KEYBOARD (MEGA BASS)
SWITCH, KEYBOARD (SOUND)
SWITCH, KEYBOARD (MD x)
SWITCH, KEYBOARD (MD B X)
SWITCH, KEYBOARD (RADIO/BAND)
S638
S640
S641
S642
1-692-014-11
1-692-014-11
1-692-014-11
1-692-014-11
SWITCH, KEYBOARD (CD x)
SWITCH, KEYBOARD (VOLUME –)
SWITCH, KEYBOARD (VOLUME +)
SWITCH, KEYBOARD (REC/REC MODE)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
21
ZS-M35
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
1.2
1.1
1.0
Date
2001. 07
2001. 03
2000. 04
Description of Revision
Change of PC Boards (Supplement-1)
Addition of Canadian and Taiwan Model
New
(ECN-RCA01727, RCA01728)
Download PDF