Cisco Explorer 1640HDC and 1642HDC Digital-Only High-Defi nition Interactive Set-Tops

Cisco Explorer 1640HDC and 1642HDC Digital-Only High-Defi nition Interactive Set-Tops
User Guide
Cisco Explorer 1640HDC and 1642HDC
Digital-Only High-Definition Interactive Set-Tops
with Multi-Stream CableCARD Interface
POWER
DATA
REMOTE
USB 2.0
Explorer 1640HDC
Notice to Installers
The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric
shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified
to do so.
Note to System Installer
For this apparatus, the coaxial cable shield/screen shall be
grounded as close as practical to the point of entry of the cable
into the building.For products sold in the US and Canada, this
reminder is provided to call the system installer's attention to
Article 820-93 and Article 820-100 of the NEC (or Canadian
Electrical Code Part 1), which provides guidelines for proper
grounding of the coaxial cable shield.
CAUTION: To reduce the risk of electric shock, do not remove cover
(or back). No user-serviceable parts inside. Refer servicing to
qualified service personnel.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This symbol is intended to alert you that uninsulated voltage
within this product may have sufficient magnitude to cause
electric shock.Therefore, it is dangerous to make any kind of
contact with any inside part of this product.
Ce symbole a pour but d’alerter toute personne qu’un contact
avec une pièce interne de ce produit, sous tension et non isolée,
pourrait être suffisant pour provoquer un choc électrique. Il est
donc dangereux d’être en contact avec toute pièce interne de
ce produit.
This symbol is intended to alert you of the presence of important
operating and maintenance (servicing) instructions in the literature
accompanying this product.
Ce symbole a pour but de vous avertir qu’une documentation
importante sur le fonctionnement et l’entretien accompagne ce produit.
20080814_Installer 820
ii
Contents
IMPORTANT SAFETY INSTRUCTIONS....................................................................................... iv
Welcome................................................................................................................................... 1
Safety First ................................................................................................................................ 1
Identify Your Set-Top ................................................................................................................ 1
What’s in the Carton? ............................................................................................................... 2
Additional Equipment You Might Need ...................................................................................... 2
Front Panel Features ................................................................................................................. 3
Back Panel Connectors ............................................................................................................. 4
Connecting the Set-Top ............................................................................................................ 5
Connections for an HDTV.......................................................................................................... 6
Connections for a Standard-Definition TV ................................................................................ 7
View Television Programming ................................................................................................... 8
Troubleshooting ........................................................................................................................ 9
Frequently Asked Questions ................................................................................................... 10
Picture Formats ....................................................................................................................... 11
Connecting to an HDTV with an HDMI Connector ................................................................... 12
Connecting to an HDTV with a DVI Connector ........................................................................ 13
Connecting to an HDTV with Component Input (YPbPr) ......................................................... 14
Connecting to a Home Theater System with Component Input (YPbPr) ................................. 15
Connecting to a Stereo VCR and HDTV (optional) .................................................................. 16
Connecting to an HDTV with a 1394 Connector ..................................................................... 17
Connecting the Set-Top in HD Mode to an SDTV with Component Input (YPbPr) .................. 17
Index ....................................................................................................................................... 18
Compliance Information .......................................................................................................... 21
iii
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
Outdoor Grounding System
2) Keep these instructions.
If this product connects to an outdoor antenna or cable
system, be sure the antenna or cable system is grounded
(earthed). This provides some protection against voltage
surges and built-up static charges.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
7) Do not block any ventilation openings. Install
inaccordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A groundingtype plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
Article 810 of the National Electric Code (NEC) ANSI/NFPA
No. 70-1990, provides the following information:
• Grounding of the mast and supporting structure
• Grounding the lead-in wire to an antenna discharge unit
• Size of the grounding conductors
• Location of the antenna-discharge unit
• Connection to grounding electrodes
• Requirements for the grounding electrodes (see the
following antenna grounding diagram as recommended by
NEC ANSI/NFPA 70)
WARNING: Avoid electric shock and fire hazard!
Do not locate an outside antenna system in the vicinity
of overhead power lines or power circuits. Touching
power lines or circuits might be fatal.
11) Only use attachments/accessories specified by the
manufacturer.
12)
Use only with the cart, stand, tripod, bracket,
or table specified by manufacturer, or sold
with the apparatus. When a cart is used,
use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
Antenna Lead In Wire
Ground Clamps
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as a power-supply cord
or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Power Source Warning
A label on this product indicates the correct power source
for this product. Operate this product only from an electrical
outlet with the voltage and frequency indicated on the product
label. If you are uncertain of the type of power supply to your
home or business, consult your service provider or your local
power company.
The AC inlet on the unit must remain accessible and operable
at all times.
Ground the Product
WARNING: Avoid electric shock and fire hazard!
If this product connects to coaxial cable wiring,
be sure the cable system is grounded (earthed).
Grounding provides some protection against voltage
surges and built-up static charges.
iv
Electric Service
Equipment
NEC = National Electrical Code 1990
National Fire Protection Association
Antenna Discharge
Unit
(NEC Section 810-21)
Grounding
Conductors
(NEC Section 810-20)
Ground Clamps
Power Service
Grounding
Electrode System
(NEC Art 250, Part H)
TO CATV INSTALLER
This reminder is provided to call the CATV system installer’s attention
to Article 820-40 of the National Electrical Code (NEC) that provides
guidelines for proper grounding, and in particular, specifies that the
cable ground shall be connected to the grounding system of the
building, as close to the point of entry as practical.
T15361
6) Clean only with dry cloth.
Protect the Product from Lightning
In addition to disconnecting the AC power from the wall outlet,
disconnect the signal inputs.
Verify the Power Source from the On/Off
Power Light
When the on/off power light is not illuminated, the apparatus may
still be connected to the power source. The light may go out
when the apparatus is turned off, regardless of whether it is
still plugged into an AC power source.
IMPORTANT SAFETY INSTRUCTIONS, continued
Eliminate AC Power/Mains Overloads
WARNING: Avoid electric shock and fire hazard!
Do not overload AC power/mains, outlets, extension
cords, or integral convenience receptacles. For
products that require battery power or other power
sources to operate them, refer to the operating
instructions for those products.
• Do not place this apparatus on an unstable surface.
• Do not install this apparatus in an enclosure, such as a
bookcase or rack, unless the installation provides proper
ventilation.
• Do not place entertainment devices (such as VCRs or
DVDs), lamps, books, vases with liquids, or other objects on
top of this product.
• Do not block ventilation openings.
Handling Disposable Batteries
Operating Environment
This product may contain disposable batteries. Heed the
following warning and follow the Battery Safety and Battery
Disposal instructions below.
This product is designed for operation indoors with a
temperature range from 32° to 104° F (0° to 40°C).
Each product should have adequate spacing on all
sides so that the cooling air vents on the chassis are not
blocked.
WARNING: There is danger of explosion if
the battery is mishandled or incorrectly replaced.
Replace only with the same type of battery. Do not
disassemble it or attempt to recharge it outside the
system. Do not crush, puncture, dispose of in fire,
short the external contacts, or expose to water or
other liquids. Dispose of the battery in accordance
with local regulations and instructions from your
service provider.
Protect from Exposure to Moisture
and Foreign Objects
WARNING: Avoid electric shock and fire hazard!
Do not expose this product to dripping or splashing
liquids, rain, or moisture. Objects filled with liquids,
such as vases, should not be placed on this apparatus.
Battery Safety
• Insert batteries correctly. There may be a risk of explosion if
the batteries are incorrectly inserted.
• Do not attempt to recharge ‘disposable’ or ‘non-reusable’
batteries.
• Please follow instructions provided for charging
‘rechargeable’ batteries.
• Replace batteries with the same or equivalent type that we
recommend.
• Do not expose batteries to excessive heat (such as sunlight
or fire).
• Do not expose batteries to temperatures above 100°C
(212°F).
WARNING: Avoid electric shock and fire hazard!
Unplug this product before cleaning. Do not use a
liquid cleaner or an aerosol cleaner. Do not use a
magnetic/static cleaning device (dust remover) to
clean this product.
WARNING: Avoid electric shock and fire hazard!
Never push objects through the openings in this
product. Foreign objects can cause electrical shorts
that can result in electric shock or fire.
Service Warnings
Battery Disposal
• The batteries may contain substances that could be harmful
to the environment.
• Recycle or dispose of batteries in accordance with the
battery manufacturer’s instructions and local/national
disposal and recycling regulations.
WARNING: Avoid electric shock! Do not open
the cover of this product. Opening or removing the
cover may expose you to dangerous voltages. If
you open the cover, your warranty will be void. This
product contains no user-serviceable parts.
• The batteries may contain perchlorate, a known hazardous
substance, so special handling and disposal of this product
might be necessary. For more information about perchlorate
and best management practices for perchlorate-containing
substance, see www.dtsc.ca.gov/hazardouswaste/
perchlorate
Check Product Safety
Provide Ventilation and Select a Location
Always disconnect the power source when moving the
apparatus or connecting or disconnecting cables.
• Remove all packaging material before applying power to the
product.
Upon completion of any service or repairs to this product, the
service technician must perform safety checks to determine that
this product is in proper operating condition.
Protect the Product When Moving It
20110316_Cable_Safety
• Do not place this apparatus on a bed, sofa, rug, or similar
surface.
v
vi
Welcome
The Cisco® Explorer® 1640HDC and 1642HDC Digital-Only High-Definition Interactive Set-Tops with Multi-Stream
CableCARD™ (M-Card™) provide high-definition (HD) capability and broadband digital video services. On the MoCA™
enabled 1642HDC, the MoCA connection enables an IP LAN connection over coaxial cable, which minimizes the
need for new wiring in the home.
Follow the instructions in this guide to install the set-top, to become familiar with the buttons on the front panel, and
to access your cable services. Then, enjoy the features of the set-top and change the way you watch TV.
Important: If the M-Card is removed, the set-top will not operate correctly.
The consumer support website provides news and information about this product. For more information, please refer
to www.cisco.com/web/consumer/support/index.html.
Safety First
Before using the set-top, read the Important Safety Instructions section of this guide.
Identify Your Set-Top
To find the serial number for your set-top, look for a label that is similar to the example shown here.
The serial number begins with “SA“ and is located at the top of the bar code.
STB SN: SABNFSRVG
STB RF MAC: 001868C16906
T15526
Set-Top
Serial
Number
If your set-top requires troubleshooting in the future, your cable service provider may ask for this serial number.
Use the space provided here to record the serial number: __________________________________________
1
What’s In The Carton?
The set-top carton contains the following items:
Quick Reference Guide
Cisco Explorer 1640HDC and 1642HDC Digital-Only High-Definition
Interactive Set-Top with Multi-Stream CableCARD Interface
POWER
DATA
REMOTE
USB 2.0
Explorer 1640HDC
POWER
DATA
REMOTE
USB 2.0
• High-Definition Set-top with M-Card
Explorer 1640HDC
• Quick Reference Guide
• Component Video Cables (YPbPr)
• Power Cord
• Audio Left/Right Cable
Additional Equipment You Might Need
You might need some of the cables and adapters shown below for connecting the set-top to your home entertainment
devices. See the connection information in the Connection Diagrams section for more information.
Check with your service provider for information about acquiring cables or adapters, or you can purchase cables or
adapters at your local electronics supplier.
S-Video
Cable
Composite
A/V Cables
HDMI
Adapter
HDMI Cable
RGB Adapter
Cable
(RCA to RCA)
RGB
Adapter
HDMI-to-DVI
Cable
2
RGB Adapter
Cable
(RCA to BNC)
RF Coaxial
Cable
RGB Adapter
Cable
(RCA to VGA)
Coaxial Digital
Audio Cable
IR Extender
Cable
Optical
Digital
Audio
Cable
IEEE
1394
4-Pin
to 4-Pin
Cable
Front Panel Features
DATA
REMOTE
USB 2.0
1
1
2
3
4
Power Button
Power LED
IR Sensor
USB 2.0 Port
2
3
4
Explorer 1640HDC
T15527
POWER
Applies power to the set-top
Illuminates when the set-top is powered on. The LED is green
Receives the infrared signal from the remote control
Connects to external equipment, such as a keyboard or a mouse, software controlled
Note: This illustration may vary from the actual product.
3
Back Panel Connectors
M-CARD SN: PKCPTMFDV
M-CARD MAC: 001BD746C7CB
1
2
3
4
5
6
7
8 10 12 14 15
9 11 13
16
1 Multi-Stream
CableCARD
Slot for M-Card module, which decrypts subscription digital channels. This set-top will not
operate correctly without an M-Card module, which is installed by your service provider
2 M-Card Code Label
Contains M-Card serial number and MAC address
3 Bar Code Label
Contains set-top serial number and MAC address
4 Cable In
Connects to a coaxial cable that delivers the signal from your service provider
5 Video Out
Connects to the composite input on your TV
6 HDTV Component
Output (YPbPr)
Connects to the YPbPr inputs on an HDTV. Do not use these connectors if you are using
the HDMI connection
7 Audio Out
Left/Right
Connects to the RCA left/right audio input on a TV
8 Optical Audio Out
Connects to an optical cable that sends a digital audio signal to a surround-sound receiver
or other digital audio device
9 Digital Audio Out
Connects to the digital audio input of a surround sound receiver or other digital audio device
10 S-Video Out
Connects to S-Video input of a standard TV or VCR
11 IR
Available to be connected to an approved remote IR receiver (purchased separately)
Please contact your service provider for details
12 HDMI
Connects an HDMI™ cable to the HDMI input of an HDTV. HDMI supports both digital audio
and video. May be used to connect to a DVI interface using an HDMI-to-DVI adapter for
video and separate audio connections. Any of the following audio connections may be used:
Stereo RCA Output (7); Digital Audio Out (8); or Optical Audio Out (9)
13 Ethernet
Connects to an Ethernet network
14 USB
Connects to external USB equipment approved by your service provider
15 1394
Connects to display devices equipped with a 1394 input
16 AC Power Input
Connects to the power cord to deliver power to the set-top (50 W max)
Note: This illustration may vary from the actual product.
4
Connecting the Set-Top
To connect your set-top to your entertainment devices, complete these steps.
1
Determine if your TV is HD or SD
and whether it is wide screen (16:9)
or standard screen (4:3). See page
11 for more information.
16
4
or
9
3
Make the connections for your TV as follows:
2

3
4
• If you are using an HDTV, see page 6 and the connection diagrams at the end of this guide.
• If you are using an SDTV, see page 7 and the connection diagrams at the end of this guide.
Identify the additional devices you will
connect to the set-top and TV. See the
Connection Diagrams section
of this guide.
DVD
D-VCR
VCR
Home Theater
Other
Plug the set-top and the TV into an AC power source that is not controlled by a switch.
POWER
5
Do not turn on the set-top or TV yet.
Wait until the POWER LED on the front panel of the set-top stops blinking to indicate that
the update is complete.
6
7
Note: If the POWER LED blinks eight times, pauses then repeats, your set-top is not authorized.
Call your service provider.
To begin watching TV, turn the TV on, and press POWER on the front panel of the set-top
or on the remote control.
5
Connections for an HDTV
To use the set-top with an HDTV, you must make one of the following connections to view the HD content. Refer to
your TV user guide and the cabling diagrams in this guide for more detailed connection information.
Note: The labeling on your set-top and HDTV may vary slightly.
Set-Top
Connections
HDMI
Required Connections to an HDTV (use one)
HDTV
Connections
Some HDTVs have a High-Definition Multimedia Interface (HDMI)
connector. The HDMI connector provides both a digital video and
audio connection.
DVI
See the connection diagram on page 12 for an example.
The HDMI connector can provide the connection to an HDTV
with a DVI input. If your HDTV has a Digital Visual Interface (DVI)
connector, you will need an HDMI-to-DVI adapter, and you will
need to connect a separate audio connection.
Adapter Needed
See the connection diagram on page 13 for an example.
YPbPr
The YPbPr connectors can provide high-definition component
video signals to an HDTV.
Note: Use the HD Setup Wizard on the set-top to set the HD
mode and select the output video format that will matches the
full capabilities of your HDTV.
DVI
L
L
R
L
R
R
Pr
Y
Pb
L
Pb
Y
R
Pr
See the connection diagram on page 14 for an example.
1394
RGB
Some HDTVs have only RGB connectors. If you have one of
these HDTVs, you need an RGB adapter.
Check with your service provider for information about acquiring
an RGB adapter, or you can purchase the adapter at your local
electronics supplier.
Some HDTVs have 1394 connectors. If you connect to your HDTV
using 1394, you also need to connect separate video and audio
connections to your HDTV.
See the connection diagram on page 16 for an example.
6
Adapter Needed
Pr
R
Pb
L
G
H
Y
R
B
V
Pr
Pr
Pb
Y
1394
L
Pb
R
Y
L
R
1394
L
R
Connections for a Standard-Definition TV
When using the set-top with an SDTV, you must make one of the following connections to view content. Some
SDTVs may not have all these connections. Refer to your TV user guide and the cabling diagrams in this guide for
more detailed information.
Note: The labeling on your set-top and SDTV may vary slightly.
S-Video
YPbPr
Required Connections to an SDTV (use one)
The YPbPr connectors can provide standard-definition component
video signals to an SDTV.
Note: To connect YPbPr to an SDTV, you must set the HD Setup
Wizard on the set-top to HD Mode, and select the output video
format (typically 480i) that will match the capabilities of your SDTV.
Set-Top
Connections
Pr
SDTV
Connections
Y
Pb
L
Pb
Y
R
Pr
The S-Video Out connection provides an optimal video connection
to SDTVs.
L
S-VIDEO
OUT
R
L
R
L
R
S-VIDEO
IN
7
View Television Programming
Access Services and Programs
Access cable services and programs by pressing the following keys on the remote control:
• Guide–Access the on-screen guide. The on-screen guide displays schedules of TV programs and other
services available from your cable service provider, such as video-on-demand and pay-per-view programs.
• Arrows–Select a program in the schedule.
• Info–Display a specific program description (either from the on-screen guide or while viewing a program).
• Select–View a specific program in the guide.
Stretch and Zoom Program
You can stretch and zoom SD or HD programs by pressing the # key on the remote control.
Avoid Screen Burn-In
Images such as letterbox bars or side bars, bright closed-captioning backgrounds, station logos, or any other
stationary images may cause the picture tube in your HDTV to age unevenly; this is known as screen burn-in. Refer
to the user’s guide that came with your HDTV for more information.
WARNING: Avoid screen burn-in. Do not display the same fixed images on your HDTV screen for
extended periods of time.
8
Troubleshooting
If the set-top does not perform as expected, the following tips may help. If you need further assistance, contact
your service provider.
No Picture
• Verify that the M-Card module is installed.
• Verify that the power to your TV is turned on.
• If the set-top is plugged into a wall switch, verify that the switch is in the ON position.
Note: You should avoid plugging the set-top into an outlet controlled by a wall switch.
• Verify that all cables are properly connected.
• If your system includes a VCR or stereo, verify that you have properly connected them to the set-top.
• The current channel may not be available in your service package. Try selecting another channel to see if a picture
appears.
No Color
• Verify that the current TV program is broadcast in color.
• Adjust the TV color controls.
• If you are using a component video connection (YPbPr), check that all connectors are completely plugged into
the set-top and TV.
No Sound
• If your setup includes a VCR or stereo, verify that you have properly connected them to the set-top.
• Verify that the volume is turned up.
• Verify that the mute function is not on.
Automatic Software Updates
A message appears on the TV screen when the set-top is receiving software updates.
9
Frequently Asked Questions
What is Digital Television?
Digital television (DTV) is a huge leap forward in television technology compared to analog television that has been
widely available since the 1940s. DTV is delivered and displayed using digital encoding, similar to the way a PC
operates. By using digital technology, there is no variation in picture and sound quality from the origination point
until it is displayed on your television. You always receive a high-quality picture without the wavy lines or static you
might sometimes get from a weak analog signal.
Because DTV receives and displays digital images that contain many times more picture elements (pixels - the
small dots that make up the color image on your screen) than standard analog television, you can get a sharper
on-screen image than with analog. Additionally, DTV supports CD-quality sound. DTV includes SDTV (StandardDefinition Television), EDTV (Enhanced-Definition Television), and HDTV (High-Definition Television). That means
that all HDTV is digital, but not all digital TV is high-definition. A high-definition program must originate in HD format
and be broadcast in HD format. Having an HDTV system does not mean that everything you watch will be in highdefinition. Getting the signal from digital cable also does not mean it is high-definition.
What is Standard-Definition Television?
Standard-definition television (SDTV) is basic digital television programming delivered by cable. Typically, the
SDTV screen is the same, nearly square shape as an analog television screen. Digital images on an SDTV set are
crisp and clear—noticeably better than on a standard analog television set using an antenna to receive over-the-air
signals.
What is High-Definition Television?
High-definition television (HDTV) is a completely new way to send and receive television broadcast signals. HDTV
images are made up of pixels that are much smaller and closer together than those used in standard analog
television, and there are millions of them. Thus, HDTV can display five to six times the detail of analog television
to deliver picture quality that is much more realistic, dimensional, and precise. SDTV programs can be viewed on
an HDTV. Another feature of HDTV is digital surround sound using Dolby™ Digital technology, which is the same
technology used to produce the sound you hear in movie theaters.
Are Local TV Stations Broadcasting in HDTV?
Many local TV stations are transmitting digital signals. However, transmitting a digital signal does not mean
transmitting an HDTV signal. Some stations are using the new bandwidth to broadcast several standard-definition
channels. Most stations, once they begin broadcasting in digital, are offering HD content from their parent network
(for example, CBS, ABC, NBC, Fox, and PBS).
Where Are the Connection Diagrams?
The diagrams at the end of this guide show examples of common ways to connect the set-top to your HDTV, DVD,
and home theater receiver. However, these diagrams do not show every possible combination of devices. Refer to
the user’s guides that came with your other electronic devices for further information.
What Cables Do I Need?
Some of the cables and adaptors shown in the diagrams may not be included with the set-top Some of the
required cables are shown in the connection diagrams and on page 2 of this guide.
10
Picture Formats
What is the Difference Between a Standard-Screen and a Wide-Screen HDTV
The type of screen your HDTV has (wide screen or standard screen) determines how the set-top displays
programs on the screen. The picture format for an HDTV is a combination of aspect ratio and screen resolution and
is different for standard-screen and wide-screen HDTVs.
What is Aspect Ratio?
An aspect ratio is the ratio of the width to the height of the TV screen. The aspect ratios differ because the
television industry manufactures both standard-screen and wide-screen HDTVs to appeal to consumer viewing
preferences.
What is the Screen Resolution and Scan Rate?
The screen resolution indicates the amount of detail that the picture displays. Resolution is identified by the number
of display lines on the screen. The techniques that an HDTV uses to “paint” the picture on the screen are referred
to as progressive and interlaced.
With the progressive method, the lines are drawn on the screen one at a time in sequential order. The interlaced
method involves refreshing pixels in alternation — first the odd lines and then the even lines.
For advance setup, select the scan modes that your TV can support. Refer to your set-top and HDTV user’s guides
to choose the proper scan rates (480i, 480p, 720p, 1080i) for your setup.
For example, a resolution of 1080i indicates that the screen shows 1080 lines in an interlaced display, and 480p
indicates that the screens shows 480 lines in a progressive display.
Notes:
• The screen resolution (1080i, 480p, and so forth) is sometimes referred to as the scan rate.
The terms are interchangeable.
• You can stretch and zoom the displayed picture using the built-in capability of the set-top by pressing the # key
on the remote control.
A standard-screen HDTV has a 4x3 aspect
ratio. The screen is 4 units wide for every 3 units
tall.
A wide-screen HDTV is one-third wider than a standardscreen HDTV. The screen is 16 units wide for every 9 units tall.
4
16
3
A screen resolution of 480p or 480i fills the screen.
9
A screen resolution of 720p or 1080i fills the screen.
11
Connecting to an HDTV with an HDMI Connector
WARNING: Electric shock hazard! Unplug all electronic devices before connecting or
disconnecting any device cables to the set-top.
Required cables:
•
1 HDMI cable
Back of Set-Top
M-CARD SN: PKCPTMFDV
M-CARD MAC: 001BD746C7CB
Cable Input
Back of
HDTV
AUDIO
CENTER
CHANNEL IN
ON
HDMI
OFF
AUDIO IN
DVI/HDCP
S-VIDEO
R
L
ANT (75 )
VIDEO
Y
VIDEO
L/
MONO
AUDIO
PB
L
PR
AUDIO
Y
L/
MONO
PB
L
R
PR
AUDIO
ANT-1
OUT
R
R
HD 1
IN
HD 2
IN
OUT
IN
ANT-2
T15529
R
Important Notes Regarding the HDMI Interface on the Set-Top
The HDMI interface automatically configures the audio output for a format supported by the television. Because
not all TVs support the Dolby Digital input, the HDMI interface may automatically select a 2-channel stereo audio
configuration instead of Dolby Digital, which it carries over to the other digital audio outputs of the set-top. This
prevents your home theater system or Dolby Digital decoder from providing the full Dolby Digital surround-sound
effect.
You can override this configuration by completing the following steps.
1. Press SETTINGS twice on the remote control to open the General Settings menu.
2. Press MOVE UP or MOVE DOWN to select the option Audio: Digital Out.
3. Press MOVE RIGHT to select Dolby Digital. This setting will send Dolby Digital audio to the HDMI, DIGITAL AUDIO
OUT, and OPTICAL AUDIO OUT connectors on the set-top.
Notes:
•
If the TV is not Dolby Digital capable, it may not produce audio through its speakers when the Audio: Digital Out
setting on the set-top is set to Dolby Digital. You can either switch the Audio: Digital Out setting back to HDMI
when you are not using the home theater or Dolby Digital decoder, or you can connect the baseband audio
outputs (OUT 1 Audio Left and Right) to the TV.
•
Digital content is encrypted with High-Bandwidth Content Protection (HDCP) on the DVI/HDMI port. This set-top
is not compatible with devices that do not support HDCP. You must use either the YPbPr or 1394 connection to
connect the set-top to these devices.
12
Connecting to an HDTV with a DVI Connector
WARNING: Electric shock hazard! Unplug all electronic devices before connecting or
disconnecting any device cables to the set-top.
Required cables:
•
•
1 HDMI-to-DVI or 1 HDMI cable and 1 DVI adapter
1 audio Left/Right cable
Back of Set-Top
M-CARD SN: PKCPTMFDV
M-CARD MAC: 001BD746C7CB
Cable Input
Back of
HDTV
AUDIO
CENTER
CHANNEL IN
ON
DVI/HDCP
IN
OFF
AUDIO IN
DVI/HDCP
S-VIDEO
R
L
ANT (75 )
VIDEO
Y
VIDEO
L/
MONO
AUDIO
PB
L
PR
AUDIO
Y
L/
MONO
PB
L
R
PR
AUDIO
ANT-1
OUT
R
R
HD 1
IN
HD 2
IN
OUT
IN
ANT-2
T15530
R
Notes:
•
When you connect the HDMI connector to the DVI connector on your HDTV, you need an HDMI-to-DVI adaptor
and a separate audio connection.
•
Digital content is encrypted with High-Bandwidth Content Protection (HDCP) on the DVI/HDMI port. This set-top
is not compatible with devices that do not support HDCP. You must use either the YPbPr or 1394 connection
(which uses Digital Transmission Content Protection, or DTCP) to connect the set-top to these devices.
•
Also refer to the Important Note Regarding the HDMI Interface on the Set-top on page 12.
13
Connecting to an HDTV with Component Input (YPbPr)
WARNING: Electric shock hazard! Unplug all electronic devices before connecting or
disconnecting any device cables to the set-top.
Required cables:
•
•
1 component video cable with 3 connectors (YPbPr)
1 audio Left/Right cable
Back of Set-Top
M-CARD SN: PKCPTMFDV
M-CARD MAC: 001BD746C7CB
Cable Input
Back of
HDTV
AUDIO
CENTER
CHANNEL IN
ON
DVI/HDCP
IN
OFF
AUDIO IN
DVI/HDCP
S-VIDEO
R
L
ANT (75 )
VIDEO
Y
VIDEO
L/
MONO
AUDIO
PB
L
PR
AUDIO
Y
L/
MONO
PB
L
R
PR
AUDIO
ANT-1
OUT
R
R
HD 2
HD 1
IN
14
IN
OUT
IN
ANT-2
T15531
R
Connecting to a Home Theater System
with Component Input (YPbPr)
WARNING: Electric shock hazard! Unplug all electronic devices before connecting or
disconnecting any device cables to the set-top.
Required cables:
•
•
•
3 component video cable with 3 connectors (YPbPr)
1 audio Left/Right cable
2 coaxial digital audio cables
Back of Set-Top
M-CARD SN: PKCPTMFDV
M-CARD MAC: 001BD746C7CB
Back of Home
Theater Receiver
Cable Input
DIGITAL
AUDIO
TV/CABLE
DVD
VIDEO 1
COMPONENT VIDEO
MONITOR
Y
Y
Y
PB
PB
PB
PR
PR
1
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
L
L
L
L
AUDIO
AUDIO
AUDIO
AUDIO
R
R
S-VIDEO
OUT
2
PR
3
1
4
R
OUT
VIDEO OUT
OUT
R
T15532
IN
IN
2
Back of Home Theater Receiver
Back of Home Theater Receiver
DIGITAL
AUDIO
TV/CABLE
DVD
VIDEO 1
COMPONENT VIDEO
Y
MONITOR
Y
Y
1
DIGITAL
AUDIO
TV/CABLE
DVD
VIDEO 1
COMPONENT VIDEO
Y
Y
Y
PB
PB
PB
PR
PR
MONITOR
1
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
L
L
L
L
AUDIO
AUDIO
AUDIO
R
R
PB
PB
S-VIDEO
OUT
PB
S-VIDEO
S-VIDEO
S-VIDEO
S-VIDEO
VIDEO
VIDEO
VIDEO
VIDEO
L
L
L
L
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
R
R
R
2
PR
PR
2
PR
PR
3
S-VIDEO
OUT
3
1
4
IN
R
OUT
IN
2
Back of
HDTV
VIDEO OUT
OUT
4
AUDIO
CENTER
CHANNEL IN
ON
1
DVI/HDCP
IN
OFF
Back of
DVD
Player
IN
R
DIGITAL
OUT
COAXIAL
OUT
IN
2
OUT
VIDEO OUT
R
AUDIO OUT
R
L
Y
PB
VIDEO
OUT
AUDIO IN
DVI/HDCP
R
L
ANT (75½)
VIDEO
Y
VIDEO
L/
MONO
AUDIO
PB
L
PR
AUDIO
PB
L
R
PR
AUDIO
T15439
R
IN
IN
OUT
PB
COMPONENT VIDEO OUT/
PROGRESSIVE SCAN
ANT-1
OUT
R
AUDIO
S-VIDEO
OUT
Y
L/
MONO
R
VIDEO-1 VIDEO-2 HD 1
OPTICAL
DIGITAL OUT
HD 2
IN
T15438
S-VIDEO
ANT-2
Note: This connection assumes
that audio is provided by the home
theater speakers.
15
Connecting to a Stereo VCR and HDTV (optional)
WARNING: Electric shock hazard! Unplug all electronic devices before connecting or
disconnecting any device cables to the set-top.
Required cables:
•
•
•
1 RF coaxial cable
2 composite A/V cables
2 audio Left/Right cables
Back of Set-Top
M-CARD SN: PKCPTMFDV
M-CARD MAC: 001BD746C7CB
Cable Input
Back of
Stereo VCR
RF IN
L
VIDEO
IN
R
L
AUDIO
IN
VIDEO
OUT
R
RF OUT
AUDIO
OUT
Back of
HDTV
AUDIO
CENTER
CHANNEL IN
ON
DVI/HDCP
IN
OFF
AUDIO IN
DVI/HDCP
S-VIDEO
R
L
ANT (75½)
VIDEO
L/
MONO
AUDIO
L
PR
AUDIO
L/
MONO
PB
L
R
PR
AUDIO
ANT-1
OUT
R
R
VIDEO-1 VIDEO-2 HD 1
R
AUDIO
HD 2
ANT-2
IN
16
PB
Y
IN
OUT
IN
T15533
Note: This connection allows
for recording to the VCR and
for watching VCR tapes on your
HDTV. To watch HD content,
use the HDMI, YPbPr, or DVI
connector.
VIDEO
Y
Connecting to an HDTV with a 1394 Connector
WARNING: Electric shock hazard! Unplug all electronic devices before connecting or
disconnecting any device cables to the set-top.
Required cables:
•
•
•
1 4-pin to 4-pin 1394 cable (Consult your TV user guide)
1 audio Left/Right cable
1 component video cable with 3 connectors (YPbPr)
Back of Set-Top
V
L
R
IR
ETHERNET
120V~
60Hz 20W
VM S/N: VMCPRPSLV
CM MAC: 0011BD73E17D9
1394
CAUTION
VM S/N: VMCPRPSLV
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CM MAC: 0011BD73E17D9
Y
CABLE IN
Pb
Pr
CABLE OUT
AVIS: RISQUE DE CHOC
OPTICAL
AUDIO OUT
USB
ELECTRIQUE NE PAS OUVRIR
Cable Input
Y
1394 IN
PB
L
R
Back of
HDTV
HD 1
IN
T15534
PR AUDIO
VIDEO
IN
Important: When you connect the set-top
to your TV using 1394, you must make the
additional video and audio connections to
your TV to receive analog signals.
Connecting the Set-Top in HD Mode to an SDTV with
Component Input (YPbPr)
WARNING: Electric shock hazard! Unplug all electronic devices before connecting or
disconnecting any device cables to the set-top.
Required cables:
• 1 component video cable with 3 connectors (YPbPr)
• 1 audio Left/Right cable
Back of Set-Top
M-CARD SN: PKCPTMFDV
M-CARD MAC: 001BD746C7CB
Cable Input
Back of SDTV
RF IN
Y
PB
PR
Note: The set-top must be set to the
proper output mode, typically 480i.
VIDEO
IN
R
AUDIO
IN
L
VIDEO
OUT
R
AUDIO
OUT
RF OUT
T15535
L
17
Index
1394
4, 6, 17
D
Dashes display
A
5
Diagrams. See Connecting the set-top
to other devices
AC
Outlet
iv, 4
Power input
Aspect ratio
Digital TV, What is it
Display, LED
4
DVI connector
11
10
3
2, 4, 6, 13
E
B
Back panel
External hard disk drive. See SATA
4
Burn-in of screen
8
F
FAQs
C
Cables
2
Cable Out, connector
4
Compliance, FCC and Canadian EMI
FCC compliance
20
Formats, picture
11
Frequently Asked Questions. See FAQs
21
Front panel
Component video connection. See YPbPr
Composite
10
3
7
H
Connectors
HD
See also Front panel; Back panel
required for HDTV
6
broadcasting
required for SDTV
7
mode
HDTV with 1394 connector
HDTV with DVI connector
HDTV with HDMI connector
HDTV with VCR
Connections
14
formats
13
16
HDMI
6
11
What is it
12
Home Theater System with component input
(YPbPr) 15
SDTV
1, 10
HDTV
17
HDTV with component input (YPbPr)
4, 5, 6, 7, 17
format
Connecting the set-top to other devices;
10
10
4, 6, 12
High-definition. See HD
Home theater system connection
17
Controls. See Front panel
I
Interlaced scan rate
IR Sensor
18
3
11
15
Index, continued
K
SD mode
Keys. See Front panel; Back panel
SDTV
4, 5, 7, 17
Connections
What is it
L
LED Display
7, 17
10
Serial number, locating
3
1
Set-top. See Welcome
Software updates
M
9
Sound, troubleshooting
M-Card
1, 4
9
Standard-definition, What is it
Standard-screen TV
P
10
11
Stretching and zooming picture
8, 11
Picture
Doesn’t display
Formats
11
No color
9
9
T
Troubleshooting
TV
Picture-in-picture. See PIP
PIP
9
digital, what is it
8
formats
Ports. See Connectors
Product information
10
11
HDTV, what is it
1
programming
Programming, viewing
8
Progressive scan rate
11
resolution
10
8
11
standard-screen
11
standard-definition, What is it
R
wide-screen
Remote control
11
8
RGB connector. See YPbPr
U
Updating, software
S
USB port
S-Video
Safety
7
9
3
V
ii, iv-v
Scan rates
10
VCR connection
11
View programs
16
8
Screen
burn-in
resolution
size
8
11
11
19
Index, continued
W
Watch TV
1, 8
Web access to product information
Welcome
1
Wide-screen TV
11
Y
YPbPr
connector
4, 6, 7
HDTV connection 14
home theater connection
SDTV connection
Z
Zoom picture
20
8, 11
17
15
1
Software and Firmware Use
FCC Compliance
United States FCC Compliance
This device has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
such interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy. If
not installed and used in accordance with the instructions,
it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment OFF and ON, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the service provider or an experienced radio/television
technician for help.
Any changes or modifications not expressly approved by
Cisco Systems, Inc., could void the user’s authority to operate
the equipment.
The information shown in the FCC Declaration of Conformity
paragraph below is a requirement of the FCC and is intended to
supply you with information regarding the FCC approval of this
device. The phone numbers listed are for FCC-related questions
only and not intended for questions regarding the connection or
operation for this device. Please contact your service provider
for any questions you may have regarding the operation or
installation of this device.
The software described in this document is protected by
copyright law and furnished to you under a license agreement.
You may only use or copy this software in accordance with the
terms of your license agreement.
The firmware in this equipment is protected by copyright law.
You may only use the firmware in the equipment in which it is
provided. Any reproduction or distribution of this firmware, or any
portion of it, without our express written consent is prohibited.
Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions
that may appear in this guide. We reserve the right to change
this guide at any time without notice.
AVC VIDEO LICENSE
With respect to each AVC/H.264 product, we are obligated to
provide the following notice:
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT
PORTFOLIO LICENSE FOR THE PERSONAL USE OF A
CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE
REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH
THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC
VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A
PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO
PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE
IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE.
ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG
LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM
Accordingly, please be advised that service providers, content
providers, and broadcasters are required to obtain a separate use
license from MPEG LA prior to any use of AVC/H.264 encoders
and/or decoders.
Declaration of Conformity
This device complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions: 1) the device may not
cause harmful interference, and 2) the device must accept any
interference received, including interference that may cause
undesired operation.
Explorer 1640HDC and 1642HDC Digital-Only High-Definition
Interactive Set-Tops
Models: 1640HDC and 1642HDC
Manufactured by: Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Telephone: 678 277-1120
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme
NMB-003 du Canada.
20081121 FCC Standard
21
Cisco Systems, Inc.
5030 Sugarloaf Parkway, Box 465447
Lawrenceville, GA 30042
678 277-1120
800 722-2009
www.cisco.com
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries.
To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.
CableCARD and M-Card are trademarks of Cable Television Laboratories, Inc.
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
MoCA is a trademark of the Multimedia over Coax Alliance.
Other third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a
partnership relationship between Cisco and any other company. (1110R)
© 2011, 2012 Cisco and/or its affiliates. All rights reserved.
August 2012
4027618 Rev B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement