IMPORTANT SAFETY INSTRUCTIONS Notice to Installers

IMPORTANT SAFETY INSTRUCTIONS Notice to Installers
IMPORTANT SAFETY INSTRUCTIONS
Notice to Installers
The servicing instructions in this notice are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so.
Quick Reference Guide
Note to System Installer
For this apparatus, the coaxial cable shield/screen shall be
grounded as close as practical to the point of entry of the cable
into the building. For products sold in the US and Canada, this
reminder is provided to call the system installer's attention to
Article 820-93 and Article 820-100 of the NEC (or Canadian
Electrical Code Part 1), which provides guidelines for proper
grounding of the coaxial cable shield.
CAUTION: To reduce the risk of electric shock, do not
remove cover (or back). No user-serviceable parts
inside. Refer servicing to qualified service personnel.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
This symbol is intended to alert you that uninsulated voltage
within this product may have sufficient magnitude to cause
electric shock.Therefore, it is dangerous to make any kind of
contact with any inside part of this product.
Ce symbole a pour but d’alerter toute personne qu’un contact
avec une pièce interne de ce produit, sous tension et non isolée,
pourrait être suffisant pour provoquer un choc électrique. Il est
donc dangereux d’être en contact avec toute pièce interne de
ce produit.
Cisco Explorer 8640HD, 8642HD, 8650HD,
and 8652HD High-Definition DVR Set-Tops
This symbol is intended to alert you of the presence
of important operating and maintenance (servicing)
instructions in the literature accompanying this product.
Ce symbole a pour but de vous avertir qu’une
documentation importante sur le fonctionnement et
l’entretien accompagne ce produit.
Explorer 8652HD
20080814_Installer820
CH+
VOL-
VOL+
POWER
1) Read these instructions.
• Location of the antenna-discharge unit
2) Keep these instructions.
• Connection to grounding electrodes
3) Heed all warnings.
• Requirements for the grounding electrodes (see the following antenna
grounding diagram as recommended by NEC ANSI/NFPA 70)
4) Follow all instructions.
5) Do not use this apparatus near water.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
WARNING: Avoid electric shock and fire hazard! Do not
locate an outside antenna system in the vicinity of overhead
power lines or power circuits. Touching power lines or circuits
might be fatal.
Protect the Product from Lightning
Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid
injury from tip-over.
Power Source Warning
A label on this product indicates the correct power source for this product.
Operate this product only from an electrical outlet with the voltage and
frequency indicated on the product label. If you are uncertain of the type
of power supply to your home or business, consult your service provider
or your local power company.
The AC inlet on the unit must remain accessible and operable at all times.
Outdoor Grounding System
If this product connects to an outdoor antenna or cable system, be sure
the antenna or cable system is grounded (earthed). This provides some
protection against voltage surges and built-up static charges.
Article 810 of the National Electric Code (NEC) ANSI/NFPA No. 70-1990,
provides the following information:
• Grounding of the mast and supporting structure
• Grounding the lead-in wire to an antenna discharge unit
• Size of the grounding conductors
INFO
EXIT
LIST
L AUDIO IN R
VIDEO IN
• Insert batteries correctly. There may be a risk of explosion if the batteries
are incorrectly inserted.
• Please follow instructions provided for charging ‘rechargeable’ batteries.
• Do not expose batteries to excessive heat (such as sunlight or fire).
When the on/off power light is not illuminated, the apparatus may still be
connected to the power source. The light may go out when the apparatus is
turned off, regardless of whether it is still plugged into an AC power source.
Disposal
• Do not expose batteries to temperatures above 100°C (212°F).
Antenna Lead In Wire
• The batteries may contain substances that could be harmful to the
environment.
• Recycle or dispose of batteries in accordance with the battery
manufacturer’s instructions and local/national disposal and recycling
regulations.
WARNING: Avoid electric shock and fire hazard! Never
push objects through the openings in this product. Foreign objects
can cause electrical shorts that can result in electric shock or fire.
Service Warnings
Ground Clamps
Electric Service
Equipment
Antenna Discharge
Unit
(NEC Section 810-21)
Grounding
Conductors
(NEC Section 810-20)
• The batteries may contain perchlorate, a known hazardous substance,
so special handling and disposal of this product might be necessary.
For more information about perchlorate and best management
practices for perchlorate-containing substance, see www.dtsc.ca.gov/
hazardouswaste/perchlorate
Provide Ventilation and Select a Location
• Remove all packaging material before applying power to the product.
Ground Clamps
Power Service
Grounding
Electrode System
(NEC Art 250, Part H)
TO CATV INSTALLER
This reminder is provided to call the CATV system installer’s attention
to Article 820-40 of the National Electrical Code (NEC) that provides
guidelines for proper grounding, and in particular, specifies that the
cable ground shall be connected to the grounding system of the
building, as close to the point of entry as practical.
• Do not install this apparatus in an enclosure, such as a bookcase or rack,
unless the installation provides proper ventilation.
Protect the Product When Moving It
• Do not block ventilation openings.
Operating Environment
Eliminate AC Power/Mains Overloads
WARNING: Avoid electric shock and fire hazard! Do not
overload AC power/mains, outlets, extension cords, or integral
convenience receptacles. For products that require battery power
or other power sources to operate them, refer to the operating
instructions for those products.
Handling Disposable Batteries
This product may contain disposable batteries. Heed the following warning
and follow the Safety and Disposal instructions below.
Check Product Safety
• Do not place this apparatus on an unstable surface.
• Do not place entertainment devices (such as VCRs or DVDs), lamps,
books, vases with liquids, or other objects on top of this product.
This product is designed for operation indoors with a temperature range
from 32° to 104° F (0° to 40°C). Each product should have adequate
spacing on all sides so that the cooling air vents on the chassis are not
blocked.
Protect from Exposure to Moisture and Foreign
Objects
WARNING: Avoid electric shock and fire hazard! Do not
expose this product to dripping or splashing liquids, rain, or moisture.
Objects filled with liquids, such as vases, should not be placed on
this apparatus.
WARNING: Avoid electric shock and fire hazard! Unplug
this product before cleaning. Do not use a liquid cleaner or an
aerosol cleaner. Do not use a magnetic/static cleaning device (dust
remover) to clean this product.
The information shown in the FCC Declaration of Conformity paragraph below
is a requirement of the FCC and is intended to supply you with information
regarding the FCC approval of this device. The phone numbers listed are
for FCC-related questions only and not intended for questions regarding
the connection or operation for this device. Please contact your service
provider for any questions you may have regarding the operation or
installation of this device.
Declaration of Conformity
WARNING: Avoid electric shock! Do not open the cover
of this product. Opening or removing the cover may expose you
to dangerous voltages. If you open the cover, your warranty will be
void. This product contains no user-serviceable parts.
Upon completion of any service or repairs to this product, the service
technician must perform safety checks to determine that this product is in
proper operating condition.
• Do not place this apparatus on a bed, sofa, rug, or similar surface.
NEC = National Electrical Code 1990
National Fire Protection Association
Ground the Product
WARNING: Avoid electric shock and fire hazard! If this product
connects to coaxial cable wiring, be sure the cable system is grounded
(earthed). Grounding provides some protection against voltage surges
and built-up static charges.
GUIDE
• Replace batteries with the same or equivalent type that we recommend.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as a power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
CH-
Safety
Verify the Power Source from the On/Off
Power Light
11) Only use attachments/accessories specified by the
manufacturer.
12)
WARNING: There is danger of explosion if the battery is
mishandled or incorrectly replaced. Replace only with the same
type of battery. Do not disassemble it or attempt to recharge it
outside the system. Do not crush, puncture, dispose of in fire,
short the external contacts, or expose to water or other liquids.
Dispose of the battery in accordance with local regulations and
instructions from your service provider.
• Do not attempt to recharge ‘disposable’ or ‘non-reusable’ batteries.
In addition to disconnecting the AC power from the wall outlet, disconnect
the signal inputs.
T15378
6) Clean only with dry cloth.
SELECT
Always disconnect the power source when moving the apparatus or
connecting or disconnecting cables.
20110316_Cable_Safety
United States FCC Compliance
This device has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against such interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy. If not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment
OFF and ON, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
This device complies with Part 15 of FCC Rules. Operation is subject
to the following two conditions: 1) the device may not cause harmful
interference, and 2) the device must accept any interference received,
including interference that may cause undesired operation.
Cisco Explorer 8640HD, 8642HD, 8650HD,
and 8652HD High-Definition DVR Set-Tops
Models: 8640HD, 8642HD, 8650HD, 8652HD
Manufactured by:
Cisco Systems, Inc.
5030 Sugarloaf Parkway
Lawrenceville, Georgia 30044 USA
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003
du Canada.
20081121 FCC Standard
With respect to each AVC/H.264 product, we are obligated to provide
the following notice:
THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO
LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES
IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO
IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii)
DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN
A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE
OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM.
Accordingly, please be advised that service providers, content providers,
and broadcasters may be required to obtain a separate use license from
MPEG LA prior to any use of AVC/H.264 encoders and/or decoders.
ROVI CORPORATION COPYRIGHT
NOTICE
This product incorporates copyright protection technology that is protected
by U.S. patents and other intellectual property rights of Rovi Corporation.
Use of this copyright protection technology must be authorized by Rovi
Corporation, and is intended for home and other limited viewing uses only
unless otherwise authorized by Rovi Corporation. Reverse engineering and
disassembly are prohibited.
Disclaimer
Cisco Systems, Inc. assumes no responsibility for errors or omissions that
may appear in this guide. We reserve the right to change this guide at any
time without notice.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
Manufactured under license from Dolby Laboratories. Dolby is a trademark of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
MoCA is a trademark of the Multimedia over Coax Alliance.
• Consult the service provider or an experienced radio/television technician
for help.
© 2009-2013 Cisco and/or its affiliates. All rights reserved.
Printed in USA
Any changes or modifications not expressly approved by Cisco Systems,
Inc., could void the user’s authority to operate the equipment.
AVC VIDEO LICENSE
Rovi is a trademark of Rovi Corporation.
Last Updated: July 2013
Part Number 78-4026879-01E0
Welcome
Connecting to an HDTV with HDMI Input
Front Panel
®
The Cisco Explorer HD High-Definition DVR Set-Tops (set-tops)
receive and deliver digital signals, and deliver high-definition
programming in exceptional picture and audio quality. Use the simple
user interface to access favorite channels and parental control
services. Contact your service provider for information about these
and other available services. Use the instructions in this guide to install
the set-top and to access your program services.
1. Unplug all electronic devices before connecting the set-top.
Explorer 8652HD
2. Connect the set-top and TV to the HDMI input as shown in the diagram.
3. Connect the set-top to the coaxial cable coming in from the wall.
CH+
VOL-
VOL+
POWER
4. Plug the TV into an AC power source.
SELECT
5. Plug the set-top’s power cord into an AC power source.
CH-
GUIDE
INFO
EXIT
LIST
The consumer support website provides news and information
about this product. For more information, please refer to:
L AUDIO IN R
7. Press the POWER key on the remote control.
http://www.cisco.com/web/consumer/support/index.html
1
2
3
4
5
6
7
9
8
Safety First
Before using this set-top read the IMPORTANT SAFETY
INSTRUCTIONS section of this guide.
Avoid Screen Burn-In
Images such as letterbox bars or side bars, bright closed-captioning
backgrounds, station logos, or any other stationary images may cause the
TV screen to age unevenly and cause damage to your TV. Refer to the user
guide that came with your TV for more information about screen burn-in.
Automatic Software Updates
A message appears on the TV screen when the set-top is receiving
software updates. In addition, download information also appears on
the front panel of the set-top during these updates. Wait for the current
time to display on the front panel before continuing. When the time
appears, the update is complete.
1 Power
2 VOL-, VOL+
3 USB 2.0
4
5
6
7
8
CH+, CHSelect
IR Sensor
Guide
Info
9 Exit
10 List
11 Display
12 Smart Card
Performance Tips
6. For the TV to receive the signal, press the appropriate button on the remote control to select the audio/video inputs to which you have
connected the set-top.
VIDEO IN
11
12
T16062
®
10
Turns the set-top on and off
Safety and Performance Tip
Decreases and increases the volume
Connects to external USB equipment approved by your
Keep the top of the set-top free of all objects
service provider, software controlled
and electronic devices, including your TV.
Scrolls up and down through the channels
Accesses your on-screen selection
Receives the infrared signal from the remote control
Accesses on-screen services, such as the on-screen guide, video-on-demand, or pay-per-view
Displays a description of the selected program. This button is available from the on-screen menu
and while viewing a program
Exit menus, the on-screen menu, and program information
Displays the recorded list
Displays the selected channel number and time of day. The display shows the following:
• Power ( )
• MoCA™ Link ( )
• 480i / 480P
• 5.1
• Message (
)
• HDTV
• 720i / 720P
• Record (
)
• Auto
• 1080i / 1080P
Allows smart card access
Back of Set-Top
OUTPUT
STB SN: SABPQBQGD
VIDEO
Y
DIGITAL
AUDIO
CAUTION
OPTICAL
AUDIO
OUT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS: RISQUE DE CHOC
ÉLECTRIQUE NE PAS OUVRIR
eCM MAC: 001AC3F4F757
IR
L
Pb
120V~
60Hz 4.2A
500W
L
STB RF MAC: 001AC3F$F756
CABLE OUT
R
Pr
R
120V~
60Hz 40W
S-VIDEO
OUT
CABLE IN
HDMI
Cable
Input
USB 2.0
AUDIO
CENTER
CHANNEL IN
ON
eSATA
1394
ETHERNET
LISTED 136MW
VIDEO PRODUCT
HDMI
OFF
AUDIO IN
DVI/HDCP
Note: This illustration may vary from the actual product.
S-VIDEO
R
L
If the set-top does not perform as expected, the following tips may help.
ANT (75 )
Back Panel
No picture
VIDEO
Y
VIDEO
• Verify that the power to your TV is turned on.
OUTPUT
• If the set-top is plugged into a wall switch, verify the switch is in
the ON position. (Avoid plugging into an outlet that is controlled by
a wall switch.)
STB SN: SABPQBQGD
VIDEO
Y
DIGITAL
AUDIO
CAUTION
OPTICAL
AUDIO
OUT
L/
MONO
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AUDIO
Pb
L
R
Pr
R
120V~
60Hz 4.2A
500W
L
R
PR
AUDIO
ANT-1
R
2
3
4 5 6
8
7
• Verify the volume is turned up.
1
2
3
4
5
6
7
• Verify the mute function is not on.
8
9
10
11
11
eSATA
12
13
14
1394
ETHERNET
15 16
17 18
Back of HDTV
Connects to a coaxial cable that delivers the signal from your service provider
Contains set-top serial number and MAC addresses
Connects to the composite input on your TV
Connects to RCA cables that send analog audio signals (left and right) to the stereo inputs on a TV
Connects to the component input (YPbPr) on the HDTV
Connects to RCA cables that send analog audio signals (left and right) to the stereo inputs on a TV
Connects to an RCA cable that sends a digital audio signal to a surround-sound receiver or other digital audio
device input
S-Video Out
Connects to an S-Video cable that sends an S-Video signal to your TV or VCR. This signal is standard-definition,
but higher quality than other SDTV connections
IR Remote Input Available to be connected to an approved remote IR receiver (purchased separately)
Cable Out
Connects to a coaxial cable that sends analog audio and video signals to a TV or VCR
Optical Audio Out Connects to an optical cable that sends a digital audio signal to a surround-sound receiver or other digital audio
device input
13 USB 2.0
14 eSATA
1394
Ethernet
AC Power Input
AC Outlet
Connects an HDMI™ cable to the HDMI input of an HDTV. HDMI supports both digital audio and video. May be
used to connect to a DVI interface using an HDMI-to-DVI adapter for video and separate audio connections. Any
of the following audio connections may be used: Audio Out (3 or 5); Digital Audio Out (6); or Optical Audio Out (10)
Connects to external USB equipment approved by your service provider, software controlled
Connects to an external Serial ATA (eSATA) hard disk drive for expanded drive space. A connected eSATA drive is
not an archival device. Ask your service provider for a list of approved hard drive models for use with the DVR
Connects to display devices that are equipped with a 1394 input
Connects to external Ethernet equipment approved by your service provider
Connects to the power cord to deliver power to the set-top
Connects to the AC power cord from another device, such as a TV
Note: This illustration may vary from the actual product.
R
HD 2
HD 2
LISTED 136MW
VIDEO PRODUCT
Cable In
Bar Code Label
Video Out
Audio Out
HDTV (YPbPr)
Audio Out
Digital Audio Out
12 HDMI
15
16
17
18
10
9
USB 2.0
T16063
1
HDMI
OUT
R
120V~
60Hz 40W
S-VIDEO
OUT
CABLE IN
No color
• If your setup includes a VCR or stereo, verify that you have properly
connected them to the set-top.
AUDIO
PB
IN
Note: This illustration may vary from the actual product.
WARNING: Electric shock hazard! Unplug
all electronic devices before connecting or
disconnecting any device cables to the set-top.
IN
OUT
IN
ANT-2
T16064
IR
L
STB RF MAC: 001AC3F$F756
• The current channel may not be available in your service package.
Try selecting another channel to see if a picture appears.
No sound
PR
L/
MONO
ÉLECTRIQUE NE PAS OUVRIR
eCM MAC: 001AC3F4F757
• Verify that all cables are properly connected.
• Adjust the TV color controls.
L
AVIS: RISQUE DE CHOC
CABLE OUT
• Verify the current TV program is broadcast in color.
PB
Y
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement