ADTRAN 4305 Network Router User's Manual
ADTRAN NetVanta 4305 is a versatile router that offers a comprehensive suite of features for diverse networking applications. With its dual wide-slot architecture, it supports a range of network modules, enabling flexible expansion and customization. The device's豐富的以太网和WAN端口(包括T1和DSX-1接口)使其适用于各种网络连接方案。凭借直观的Web界面和命令行界面,该路由器易于配置和管理。此外,NetVanta 4305还提供了高级功能,如虚拟专用网络(VPN)加速、防火墙和服务质量(QoS)管理,使其成为企业和服务提供商的理想选择。
Advertisement
Advertisement
®
Quick Start Guide
NetVanta 4305 Router
For more detailed documentation, visit us online at www.adtran.com
.
P/N 1200890L2
STATUS
WAN
DBU
NET 1
TD
RD
G ETTING S TARTED
WAN
DBU
NET 2
TD
RD
LAN 1
TD
RD
LNK
LAN 2
TD
RD
LNK
WIDE SLOT 1
STATUS
ACTIVITY
TEST
Two configuration methods are available for your NetVanta router:
• Web-based GUI
• AOS Command Line Interface (CLI)
The GUI lets you configure the main unit settings and provides online guidance and explanations for each setting. However, using the AOS CLI may be necessary for more advanced configurations.
A CCESS THE GUI
You may access the web-based GUI from any web browser on your network by following these steps:
1.
Connect the router to your PC using the ETH 0/1 port on the back of the unit.
2.
Set your PC to a fixed IP address of 10.10.10.2. If you cannot change the PC’s IP address, you will need to change the unit’s IP address using the CLI. (Refer to the next two sections for instructions.)
3.
Enter the unit’s IP address in your browser address line. The default IP address is 10.10.10.1.
4.
You will then be prompted for the username and password (the default settings are admin and password).
5.
The initial GUI screen appears.
A CCESS THE CLI
Access the AOS CLI via the CONSOLE port or a Telnet session. To establish a connection to the
NetVanta router CONSOLE port, you need the following items:
• VT100 terminal or PC (with VT100 terminal emulation software)
• Straight-through serial cable with a DB-9 (male) connector on one end and the appropriate interface for your terminal or PC communication port on the other end
1.
Connect the DB-9 (male) connector of your serial cable to the CONSOLE port on the rear panel of the unit.
2.
Connect the other end of the serial cable to the terminal or PC.
3.
Insert the connector of the provided power cord into the power interface on the rear panel of the unit, and plug the cord into a standard electrical outlet.
NetVanta 4305
4.
Once the unit is powered up, open a VT100 terminal session using the following settings:
9600 baud, 8 data bits, no parity bits, and 1 stop bit. Press <Enter> to activate the
AOS CLI.
5.
Enter enable at the > prompt.
6.
Enter the enable password when prompted. The default password is password.
The configuration parameters used in the examples outlined in this document are for instructional purposes only. Please replace all underlined entries ( example ) with your specific parameters to configure your application.
C
ONFIGURE THE
U
NIT
’
S
IP A
DDRESS
The following steps create an IP address (10.10.10.1 255.255.255.0) for Ethernet port 0/1. If you are not sure what IP address to assign, please contact your network administrator.
1.
At the # prompt, enter config terminal.
2.
At the (config)# prompt, enter interface eth 0/1 to access the configuration parameters for the ETH 0/1 port located on the rear of the unit.
3.
Enter ip address 10.10.10.1 255.255.255.0 to assign an IP address to the ETH 0/1 port using a 24-bit subnet mask.
4.
Enter no shutdown to activate the interface to pass data.
5.
Enter exit to exit the Ethernet interface commands and return to the Global Configuration mode.
Depending on your configuration, you may need to set a default gateway as well using the (config)#ip default gateway command. If IP routing is enabled on the unit, do NOT set a default gateway.
Quick Start Guide, 61200890L1-13D, July 2005 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright © 2005 ADTRAN, All Rights Reserved
®
Quick Start Guide
NetVanta 4305 Router
For more detailed documentation, visit us online at www.adtran.com
.
P/N 1200890L2
ETH 0/2 100 -250VAC, 0.75A
50/60Hz
WAN-T1 DSX-1 DBU
CONSOLE
SLOT 3 WIDE MODULE SLOT 2 NET/DBU SLOT 1 NET/DBU
ETH 0/1
5
6
3
4
Pin
1
2
7
8
9
E NABLE T ELNET A CCESS
The following steps create a password of adtran for Telnet access. By default, Telnet access is enabled with a password of password.
1.
Verify that the prompt of your unit displays (config)#.
2.
Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions.
3.
Enter login to initiate Telnet access.
4.
Enter password adtran to change the login password for the Telnet sessions.
5.
Enter exit to return to the Global Configuration mode.
6.
Verify that the prompt of your unit displays (config)#.
7.
Enter do write memory to save the current configuration.
C ONSOLE P INOUTS
Name
DCD
RD
TD
DTR
SG
DSR
—
CTS
—
Description
Data Carrier Detect (output)
Receive Data (output)
Transmit Data (input)
Data Terminal Ready (input)
Signal Ground
Data Set Ready (output)
Unused
Clear to Send (output)
Unused
For information on installing the VPN Accelerator Card, please refer to the
NetVanta 4305 Hardware Installation Guide on the ADTRAN OS System
Documentation CD included in your router shipment.
E
THERNET
P
INOUT
Pin
1
2
3
4, 5
6
7, 8
Name
TX1
TX2
RX1
—
RX2
—
Description
Transmit Positive
Transmit Negative
Receive Positive
Unused
Receive Negative
Unused
C ONFIGURE Y OUR A PPLICATION
More detailed documentation for configuring your ADTRAN unit is provided on the ADTRAN OS
System Documentation CD included in your shipment. For more detail on hardware setup, refer to the appropriate NIM Quick Start Guides and the Hardware Installation Guide. For more detail on configuring your system, refer to the ADTRAN Operating System (AOS) Command Reference
Guide, configuration guides, and technical support notes.
Important: For additional details on product features, specifications, installation, and safety, refer to the appropriate Hardware Installation
Guide on the ADTRAN OS System Documentation CD shipped with the base unit and available online at www.adtran.com.
Quick Start Guide, 61200890L1-13D, July 2005 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright © 2005 ADTRAN, All Rights Reserved

Public link updated
The public link to your chat has been updated.
Advertisement