Dacor ETT3652RF Cooktop Installation guide
Advertisement
Advertisement
Installation Instructions
Millennia ® Electric Cooktop
For use with models ETT304-1, ETT365-2, MET304 and METB365-1
Part No. 65170 Rev. d
TESTED IN ACCORDANCE WITH THE LATEST EDITION OF ANSI Z21.1 AND
U.L. 858 STANDARD FOR HOUSEHOLD COOKING APPLIANCES.
Before You Begin ..............................................................
1
Important Safety Instructions ..........................................
1
Important Information About Safety Instructions .............. 1
Safety Symbols and Labels .............................................
1
General Safety Precautions .............................................
2
Installation Specifications ................................................
3
Product Dimensions .........................................................
3
Electrical Specifications ...................................................
3
Planning the Location ......................................................
4
Cabinet Layout .................................................................
Installation Instructions ....................................................
Chassis Installation ..........................................................
4
6
6
Verify the Package Contents ............................................
6
Electrical Connection .......................................................
6
Verifying Proper Operation ...............................................
8
If You
Need
Help...
If you have questions or problems with installation, contact your Dacor dealer or the Dacor Customer Service Team.
For repairs to Dacor appliances under warranty call the
Dacor Distinctive Service line. When you call, have the model and serial number of the appliance ready. The model and serial number are printed on the product data label.
Dacor Customer Service Team
Phone: (800) 793-0093 (U.S.A. and Canada)
Monday -- Friday 6:00 A.M.to 5:00 P.M.Pacific Time
Web site: www.Dacor.com
Dacor Distinctive Service (for repairs under warranty)
Phone: (877) 337-3226 (U.S.A. and Canada
Monday -- Friday 6:00 A.M.to 4:00 P.M.Pacific Time
Product Data Label
• The product data label contains the model and serial number information and the electrical requirements.
• It is located on the bottom of the cooktop chassis.
All specifications are subject to change without notice. Dacor ®assumes no liability for changes to specifications.
© 2007 Dacor, all rights reserved.
Important:
• Installer: In the interest of safety and to minimize problems, read these installation instructions completely and carefully before you begin the installation process. Leave these installation instructions with the customer.
• Customer: Keep these installation instructions for future reference and the local electrical inspector's use.
Important Information About
Safety Instructions
• The Important Safety Instructions and warnings in this manual are not meant to cover all possible problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance.
• Always contact the Dacor Customer Service Team about problems and conditions that you don't understand. See Customer Service Information.
Safety Symbols and Labels
_DANGER
IMPORTANT: DOnot store or use c0mbustiblel flamma.
ble or explosive vapors and liquids (such as gasoline)on or in the vicinity of this or any other appliance. Also keep items that could explodel such as aerosol cans, away from the c0oktop. DO not store flammable or explosive atedals in adjacent cabinets or areas (including above and below the cooktop).
[_ WARNING
WARNING.
NEVER use this appliance as a space heater to heat or Warm the rooml D0ing so may result in I overheating of the appliance.
I
I
DANGER
Immediate hazards that WILL result in severe personal njury or death ...........................
[_
WARNING
Hazards or Unsafe practices that COULD result in severe personal injury or death.
[_
WARNING
WARNING ' NEVER cover anY Vents, slots, holes or passages on the cookto p chassis, Doing so blocks air flow through the cooktop and may cause a fire hazard1
I
I
I
I
[_ WARNING
Do not install this appliance outdoors andi0r near Watefl for examp el near a pool
I
CAUTION
Hazards or Unsafe practice s that COULD result in personal injury or property damage.
I
READ AND SAVE THESE INSTRUCTIONS
_=lc'clr_ 1
General Safety Precautions
To reduce the risk of fire, electric shock, serious injury or death when using your appliance, follow basic safety precautions, including the following:
WARNING
' Read the accompanying use and care manual before operating this appliancel iKeep' packaging materials away from children:Plastic sheets and bags can cause suffocationl
, If you receive a damaged PrOduct, immediately co ntact your dealer or builder. D0not install cruse a damaged appliancel Do not install cruse the appliance if the conduit is damaged!
This; appliance must be properlY installed and groundL edby a qualified installer according to these installa_ tion instructions Prior to use. The installer must show the customer the location of the circuit breaker panel or fuse box so that they know where and how to turn off power to the co0ktop. Dacor is no t responsible for the cost of correcting PrOblems caused by improper installation, The owner is responsible to make sure this appliance is properly installed:
' D0 not install, repa ror replace any part of the
Cookt0P unless specifically recommended in the literai ture accompanying it. A qualified service technician must perform all other servicel
'i Before performing any type of service or installati0n make sure that power t0 the applianCe is turned off at the circuit breaker panel or fuse box.
Only use the cooktoP for cooking tasks expected of a home appliance as outlined in the literature accompa, hying t: This cooktop is not intended for commercial or industrial Usel
' D0not use €ori0sive chemicals or Vapors 0n °rin the
VicinitY of this appliancel Clean this appliance 0nly in the manner specified in the use and care manual.
; D0 n0t climb on any part of the appliancel
' not leave Children 0r pets a One or unattended in the area around the cooktoPl Donot allow children to play with the controls.
;' DO n0t Store items Of interest to children above or on top of the cookt0P. Children could be burned or injured while climbing on the appliancel
• Do not tamper with the controls. Do not adjust or alter any part of the cooktop unless specifically instructed to do so in this manual.
WARNING
• To avoid a fire hazard, do not hang flammable or heat sensitive objects over the cooktop.
• Do not place anything other than cooking utensils on top of the cooktop. Do not use the cooktop as a table or shelf.
• If the cooktop is near a window, do not use long curtains as window treatment.
The curtains could blow over the cooktop and create a fire hazard.
• DO NOT TOUCH THE SURFACES OF THE
COOKTOP DURING OR IMMEDIATELY AFTER USE.
After use. make sure these surfaces have had sufficient time to cool before touching them.
• Do not wear loose or hanging apparel while using the cooktop. Do not allow clothing to come into contact with hot surfaces and the surrounding areas during and immediately after use.
• Do not heat unopened food containers such as baby food jars and cans or eggs. Pressure build up may cause the container to burst and cause injury.
• Do not allow pans to boil dry.
• Do not store plastic or other utensils with low melting temperatures in drawers immediately below the cooktop.
• Clean the cooktop before using it for the first time according to the use and care manual.
• Non-stick coatings, when heated, can be harmful to birds. Remove birds to a separate, well-ventilated room during cooking.
plastic and cloth away from hot surfaces. Do not put such items on the cooktop.
Do not allow pot holders to touch hot surfaces.
2 _mC_
Product Dimensions
30 1/4" *
(768 mm)
A, tolerances: +1/16 (+1.6 mm), unless otherwise stated.
4" (102 mm)
Chassis height
21 1/4" *
(540 mm)
19 3/8"
(495 mm) jJ
28 3/8"
(721 mm) 36 1/4" *
(921 mm)
4" (t02 mm)
Chassis height
Models ETT304-1, MET304
34 3/8"
(873 mm)
_.
21 1/4"*
(540 mm).
19 3/8"
(495 mm)..
* For units with stainless steel trim, other units may be up to 1/8" less
Models ETT365-2, METB365-1
Electrical Specifications
[_
IMPORTANT
This appliance is Pr0vided with electrical connection leads in a flexible metal conduit: These leads may be a sma!ler gage than the standard household Wiring of the dedicated supply circuit, but they are suitable for connection to these circuits under the Jurisdiction of the National
Electric Code, andior the local inspection authority.
It is the owner's responsibility to ensure that a licensed electrician performs the installation of the electrical supply for this appliance. The electrical installation, including minimum supply wire size, must comply with the
National Electric Code ANSI/NFPA 70 (latest revision) and local codes and ordinances. A copy of the standard may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
The correct voltage, frequency and amperage must be supplied to the appliance from a dedicated, grounded, circuit that is protected by a properly sized circuit breaker or time-delay fuse. If a time-delay fuse is utilized, fuse both sides of the line (L1 and L2).
• The junction box and the remote circuit breaker panel or fuse box, must be accessible when the cooktop is in place.
Model
ETT304-1
ETT365-2
MET304
METB365-1
Dedicated
Circuit Required
240 Vac, 60 Hz.
3 wire* 40 Amp.
240 Vac, 60 Hz.
3 wire* 40 Amp.
240 Vac, 60 Hz.
3 wire* 40 Amp.
240 Vac, 60 Hz.
3 wire* 50 Amp.
Total Connected
Load**
6.9 kW
(29 Amp.)
9.1 kW
(38 Amp.)
6.9 kW
(29 Amp.)
9.6 kW
(40 Amp.)
Two 120 Vac hot 'L1 and L2) and one ground (all copper).
** For reference only. See the product data label (on the bottom of the unit) for exact specifications.
The minimum wire size required by the manufacturer is 8 AWG. Local codes may require that minimum wire gauge used exceed this requirement for the power requirements listed on the product data label.
_mCD_ 3
WARNING
° IMPORTANT: Observe all governing codes and ordinances during planning and installation. Contact your local building department for further information.
° To reduce the risk of a fire hazard, all minimum/maximum clearances shown must be met or exceeded.
° When installing model ETT365-2 or METB365-1 and the bottom of the chassis is to be enclosed wall to wall, you must install ventilation duct kit ATD323. See the duct installation instructions for cutout req uirements.
Planning the Location
• Dacor recommends installing a non-combustible material on the rear wall behind the cooktop.
• Carefully check the location where the cooktop is to be installed. It should be placed for convenient access.
• To reduce the risk of personal injury caused by reaching over a hot appliance, cabinet storage space located directly above the cooktop should be avoided.
Make certain that electrical power meeting the specifications on page 3 can be provided in the selected location. Verify that the electrical location is permitted by local building codes. Locate the junction box within reach of the included 48 inch long (1219 ram) cooktop power conduit attached at the bottom right rear of the chassis. Do not lengthen the wiring. Make sure the underside of the cooktop and the junction box are accessible for inspection and service.
Cabinet Layout
Under Counter Clearance
Allow a minimum of six(6) inches (152 mm) clearance between the base of the glass cooktop frame and any combustible surface below, including the upper edge of drawers below the cooktop. Proper under-cabinet clearance is also required for the cooktop hold down brackets.
A
t
6" (152 mm)
Min. clearance to combustible surfaces
Cooktop Models
ETT304-1, MET304
ETT365-2, METB365-1
A - Minimum Under Counter
Clearance (Width)
30 1/2" (775 mm)
36 1/2" (927 mm)
Under Counter Clearance - All Installations
Ventilation
To reduce the risk of personal injury and to reduce accumulated smoke in the room, Dacor strongly recommends installing a vent hood or raised vent. Install the vent hood or raised vent according to the accompanying installation instructions. A vent hood should cover the entire cooking surface below it.
If installing the cooktop with a raised vent, install only the following approved Dacor model numbers:
Cooktop Models
ETT304-1 MET304
Approved Raised Vent Models
ERV30, PRV30 or RV30
ETT365-2 METB365-1 ERV36, PRV36 or RV36
Raised vent installation must allow room for the stiffener bar on the back of the raised vent chassis. See below.
Stiffener
3/8" Min. (10 mm) flat countertop overhang
. required behind cutout
,,, i /
.[_ to determine proper fit
Countertop
]
\\
-blt
ETT or MET series cooktop
'_ql in
L ------
7-'
Cabinet face _'
/ l ,
"
1i
II_[J 3/8" Min. (10 mm) space ', behind raised vent _'l ,l/ chassis to clear stiffener ,,
II I/
II IL_ ERV or PRV series raised ',
', ',
I
II IT vent: Check raised vent
I dimensions/specifications i
',
Floor in
,,''
I I
Side View: Cooktop and ERV/PRV Series Raised Vent
5/8" Min. (16 mm) overhang Count_rtop
Stiffener
:/ ' tl
•
\\
,_%
I t i
ETT or MET series cooktop 11
""
iJJn
Cabinet face
--5/8" MIn.(16 mm) space ' 1
.r_
II behind raised vent ii
',,
"
i in ....
i!
I U_ RV series raised vent: i li
Check raised vent ,,
I 1
"'
I II dimensions/specifications
• ,
I /I
to determine proper fit II i
',', i
.............................
.........................
Floor
___J T,
I I
I I i
"
i i ii
I
I
I i I
.l_ I
Side View: Cooktop and RV Series Raised Vent
4 i::_=1c1:7r,
Cabinet Cutout Dimensions
Before making the countertop cutout, make certain that the required dimensions shown below have been met or exceeded.
All tolerances: +1/16,-0 (+1.6 mm,-0), unless otherwise stated.
f
Rear wall
Dimension Table -
Installations without Raised Vent
Models
A - Cooktop
Cutout Width
ETT304-1, MET304 28 3/4" (730 mm)
ETT365-2, METB365-1 34 3/4" (883 mm)
2 1/4" Min.
(502 mm)
(57 mm) \
(25 mm)
ISO view without raised vent
"_"'-6" (152 mm)
Min. to combustible, side wall, both sides
Countertop Cutout Dimensions Without a Raised Vent Installed
Cabinet face
E
D
C
19 3/4"
T
(502 mm) !
6" Min._
(152 mm)
B
1" Min.
(25 mm)
t
Rear wall
ISO view with raised vent
_', - 6" Min.
(152 mm)
Top view with raised vent
Countertop Cutout Dimensions With Raised Vent Installed
Model/Configuration
ETT304-1 or MET304 cooktop with ERV30 or PRV30 raised vent.
ETT304-1 or MET304 cooktop with
RV30 raised vent.
ETT365-2 or METB365-1 cooktop with ERV36 or PRV36 raised vent.
ETT365-2 or METB365-1 cooktop with RV36 raised vent.
Dimension Table - Installations with Raised Vent
A - Cooktop
Cutout Width
B - Raised
Vent Cutout
Width
C - Total
Cutout Depth
28 3/4"
(730 mm)
34 3/4"
(883 mm)
27 3/4"
(705 mm)
33 3/4"
(857 mm)
22 1/2"
(572 mm)
22 1/4"
(565 mm)
22 1/2"
(572 mm)
22 1/4"
(565 mm)
D - Raised
Vent
Cutout Depth
2 3/4"
(70 mm)
2 1/2"
(64 mm)
2 3/4"
(70 mm)
2 1/2"
(64 mm)
E - Min. Rear
Countertop
Overhang
3/8"
(10 mm)
5/8"
(16 mm)
3/8"
(10 mm)
5/8"
(16 mm)
_mCD_ 5
Verify the Package Contents
Verify that all the items below have been provided. If any item is missing or damaged, please contact your dealer immediately.
Do not install a damaged or incomplete appliance. Make sure that you have everything necessary to ensure proper installation before proceeding.
• Foam tape
• Mounting brackets (2)
• Glass scraper
• Dacor Cooktop Cleaning Creme
• Product literature
Chassis Installation
,
Secure the cooktop to the countertop utilizing the two
(2) hold-down brackets provided. Slide the brackets into the slots located on the left and right sides of the chassis, then tighten the screws to the underside of the countertop.
Cooktop Foam tape seal Countertop old down bracket and screw
[_
WARNING
If the electrical service provided does not meet the speci: fications on pages, d0 not proCeed With the installati0n
Call a licensed electrician to install the required wiring.
[
I
I
[_
IMPORTANT
' Do not over-tighten the hod down bolt&overt ghten, ing the hold down bolts may Jesuit in damagel
, Do not use a hardening compound, glue or caulk to seal the cooktop into placel The co0ktop mus t be readily removable if service is requiredl Removal of any sealant t O service the unit Will be performed atthe customeCs expense:
1.
If the cooktop will be used with a raised vent, install the vent according to it's installation instructions first. Install it in the back of the cutout.
2.
Attach the foam tape provided with the unit to the underside of the cooktop mounting surface.
Electrical Connection
[_ WARNING
To prevent an electric shock or fire hazard, turn off power to the circuit at the circuit breaker or fuse box prior to connecting the cooktop wiring to the junction box.
• Failure to connect the cooktop electrical wiring as specified may result in an electric shock hazard, a fire hazard and damage to the appliance.
• Connect the ground (green) wire from the appliance to a grounded, metallic, permanent wiring system or grounding conductor. DO NOT ground the appliance with a neutral (white) house supply wire. A separate ground wire must be utilized.
• This appliance must be properly grounded according to these instructions any time power is applied.
• If aluminum house supply wiring is utilized, splice the appliance copper wires to the aluminum house wiring using special connectors designed and agency-certified for joining copper and aluminum.
Follow the connector manufacturer's recommended procedure carefully. Improper connection may result in a fire hazard.
Foam tape
3.
Lower the cooktop into the cutout and center it.
I
out for servicing.
[_
IMPORTANT
1.
Before proceeding, turn off power to the circuit to which the cooktop will be connected at the circuit breaker panel or fuse box.
2.
Feed the appliance conduit into the electrical junction box and attach it using a UL certified strain relief.
,
Depending upon local codes, utilize one of the two methods shown on the facing page to connect the appliance to the power.
I
6 _mC_
Three Wire Electrical Connection
See diagram on right.
1.
Separate the wires coming out of the appliance conduit.
2.
Connect the black wire from the appliance conduit to the black (L1) supply wire in the junction box.
3.
Connect the red wire from the appliance conduit to the red (L2) supply wire in the junction box.
4.
Connect the green wire from the appliance conduit to the green (ground) wire in the junction box.
Junction box
Incoming power
Wire nut,
3 places
Three Wire Electrical Connection with
External Ground
[_ WARNING
• Donot groun d the appl!ance to a gas supply pipe or
• If connecting the ground wire toa grounded cold water pipe, connect it using a separate copper grounding wire (No. 10 minimum) and a clamp with an external grounding screwl The grounded cold Water pipe must have metal continuity to electrical ground and must not be interrupted by insulating materialsl Any insulating materials must be jumped with a minimum 4AWG wire to establish continuity to groundl See diagram below right.
[_
NOTE
If the junction box has been properly grOunded bY a licensed electrician, the green (ground)wire from the appliance conduit may be connected to the Junction bOX using a loop terminal.
See diagrams on right.
1.
Separate the wires coming out of the appliance conduit.
2.
Connect the black wire from the appliance conduit to the black (L1) supply wire in the junction box.
,
,
Connect the red wire from the appliance conduit to the red (L2) supply wire in the junction box.
Connect the green wire from the appliance conduit to a grounded cold water pipe as shown. Jumper any insulating materials as shown with a length of No. 4 copper wire. Securely clamp the wire to bare metal at both ends.
Conduit to cooktop
Three Wire Connection
Separate 10 AWG
Clamp wire tightly to cold water pipe
\ wire minimum _ ._
Incoming power
I
Junction box
Wire nut,
/
3 places
1_ GREEN
GREEN
, BLACK [_
_ Conduit to cooktop
Three Wire Connection with External Ground
4 AWG wire
(minimum)
Insulating device
/j
......
; iomota,
Insulated Pipe Jumper
_mCD_ 7
Verifying Proper Operation
I
Read the accompanying use and care manual completely
_] WARNING before using the cooktopl
1.
Clean the cooking surface according to the use and care manual prior to use.
,
Turn on the power to the cooktop at the circuit breaker or fuse box. When the unit is powered on for the first time, the cooktop controls will go through a self-check routine. For safety, when the self-check is complete, the cooktop controls will go into locked mode. Unlock the element controls:
On ETT series models, push and hold the Dacor logo key for three seconds. Three beeps should sound and the Dacor logo indicator light should go out.
,
,
0 On MET series models, push and hold the
CANCEL • SECURE key for three seconds. Three beeps should sound and the CANCEL • SECURE indicator light should go out.
Turn on the left rear element by pressing the left rear
ON/OFF key. Press the 8 setting key (on the same row) to select heat level 8. Verify that the element begins to heat, then turn it off by pressing the ON/OFF key.
Repeat step 3 for the remaining burners. The left front burner has two different elements, an inner one and an outer one. To activate the outer element:
Press the ON/OFF key for the left front element and press the 8 number setting.
Activate the outer element by pressing the outer element key (the circle) on the right side of the element control.
,
0 On model METB365-1, turn on both the right front and left front elements on setting 8, then press the bridge element key to verify it is working.
For safety, lock the controls after testing is complete.
NOTE: If the cooktop does not operate properly, follow these troubleshooting steps:
O Verify that power is supplied to the cooktop.
0
Check for proper electrical connections.
0 Make sure the cooktop controls are not locked (see step 2).
0
Repeat the above tests.
0 If the appliance still does not work, contact Dacor
Distinctive Service at (877) 337-3226. Do not attempt to repair the appliance yourself. If you need service, be sure to have the model and serial numbers available when you call. They are located on the bottom of the appliance.
8 _mC_
0 ° o o
O_4tO_ '
_ oO o_JO_ '
5
6
1
9 i0 "_t
5
6
,0 _
9 _I € J
O
9 10
3
5
6
3
5
6
7
9,0
5
6
1
5
6
1
S
9,0
5
6
9 ,0 _
O
S
Outer element key
9 ,0
5
6
5
6
1
S
9,0%;/
Outer element key
Cooktop Controls - Model ETT304-1
Cooktop Controls - Model ETT365-2
go
@o
ON/OFF
--_ 1 2 3 4 5 6 7 8 9 10 Ill/
OO
@O
ON/OFF
--_ 1 oo
®o
ON/OFF
--_ 1
OO
@o
ON/OFF
--_ 1
2 3 4 5 6 7 8 9 10 I/I/
2 3 4 5 6 7 8 9 10 /Ill
2 3 4 5 6 7 8 9 10 /Ill
0
Outer element key
Cooktop Controls - Model MET304
_O 0 S 1 2 3 4 5 6 7 8 9 10 /Ill
00
ON/OFF
I 1 2 3 4 5 6 7 8 g 10 I/I/
0_}
ON/OFF o 1 2 3 4 5 6 7 8 9 10 Ill/
0
000
ON/OFF
I 12 3 4 5 6 7 8 9 10 /Ill
Outer element key
80_
ON/OFF
S 1 2 3 4 5 6 7 8 9 10 Ill/ 8
_'_
X
Bridge element key
Cooktop Controls - Model METB365-1
_mCD_ 9
®
The Life of the Kitchen?
Dacor • Phone: (800)793-0093 • FAX: (626)403-3130 • www.Dacor.com

Public link updated
The public link to your chat has been updated.
Advertisement