advertisement
TL-PA211
AV200 Mini Powerline Adapter
Rev: 1.0.0
1910010392
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2010 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com
I
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user‟s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
II
Important Safety Instructions
1. Do Not open this product or attempt to service this product, it may expose you to dangerous high voltage and other risks.
2. Do Not operate this product near water.
3. Do Not place or operate near or over radiator or heat register.
4. Do Not expose this product to dampness, dust or corrosive liquids.
5. Do Not connect this product and Disconnect from wall socket during a lightning or thunderstorm
6. Do Not obstruct this product ventilation slots, as insufficient airflow may harm this product.
7. Do Not put anything on this product.
8. Plug directly into wall socket (100Vac~240Vac). Do Not use an extension cord between this product and the AC power source.
9. When plugging this product into wall socket, make sure that electrical socket are not damaged, and no leakage for gas or water pipes to begin with.
10. Place the connecting cables carefully so people won‟t stumble or walk on it.
11. The Powerline Adapter should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult the qualified technician.
12. Unplug the Powerline Adapter from the mains and refer the product to qualified service personnel for the following conditions:
If liquid has been spilled on the product
If the product has been exposed to rain or water
13. Unplug from the wall socket before cleaning. Use a damp cloth for cleaning. Do not use liquid cleaners or aerosol cleaners.
14. The specification of the fuse is T2.5AL250V. To avoid damage, please do not change the fuse.
15. The Operating temperature is 0℃~42℃ (32℉~107.6℉).
16. The Storage temperature is -40℃~70℃ (-40℉~158℉).
III
CONTENTS
– Computer .......................................................................... 4
Chapter 5 Advance Feature: How to Use the Push buttons ....................................... 20
IV
TL-PA211 AV200 Mini Powerline Adapter
Chapter 1 Introduction
Congratulations on your purchase of this outstanding Mini Powerline Adapter. This device is an AV200
Mini Powerline Adapter which transforms your house‟s existing electrical wiring into an ubiquitous networking infrastructure. Simply plug this AV200 Mini Powerline Adapter into an ordinary AC power outlet which will easily extend your Cable/xDSL broadband connection or existing Ethernet (LAN) network to any other electrical outlet in any room of a house without the need of any new cabling.
This Mini Powerline Adapter supports up to 200Mbps data rate over the existing household power circuit.
With data rates of 200Mbps, full multimedia application can easily be supported throughout the whole house in addition to Internet access. This Mini Powerline Adapter uses the existing power lines installed in a home as a path to transmit digital data, voice, audio and video between devices.
To ensure data communication‟s security and multimedia applications, this Mini Powerline Adapter support built-in 128-bit AES encryption and Quality of Service (QoS) features.With minimum setup, you can install and use this Mini Powerline Adapter within minutes. The adapter adds two useful functions.
1． Existing connection with a new unassociated device added via the Pair button.
2． Reset to default setting via the Management Utility.
A. System Requirement a) At least two AC 100V ~ 240V power outlets with standard home power wiring b) A computer with the following:
Operating System with TCP/IP installed
Pentium III compatible processor and above
Ethernet LAN card installed with TCP/IP protocol
64 MB RAM or more
50 MB of free disk space (Minimum)
CD-ROM Drive
B. Package Contents
The AV200 Mini Powerline Adapter package contains the following items:
One AV200 Mini Powerline Adapter (There are two AV200 Mini Powerline Adapters in Starter Kit)
One CAT-5 Ethernet Cable (There are two CAT-5 Ethernet Cables in Starter Kit)
One Quick Installation Guide
One CD-ROM (Utility / Manual / Quick Installation Guide/Acrobat Reader)
If any of the above items are damaged or missing, please contact your dealer immediately.
1
TL-PA211 AV200 Mini Powerline Adapter
Chapter 2 Connecting Mechanism
2.1 Introduction
The Mini Powerline Adapter supports up to 200Mbps data rate. With this high speed connection rate, this Mini Powerline Adapter allows you to setup a high speed home network by using your home existing electrical wiring. Simply plug this Mini Powerline Adapter into an ordinary power outlet to extend your
Cable/xDSL broadband connection or existing LAN network to any other electrical outlet in any rooms of your house.
Take notes that this Mini Powerline Adapter works in pairs. You need to plug one Mini Powerline Adapter into a power outlet for each computer (Connect to the computer LAN card) you want to connect
(Network access); you will also need another Mini Powerline Adapter connected to your Cable/xDSL broadband (Ethernet port) in order to extend your broadband connection or Internet surfing. With clean powerline, the distance between two Mini Powerline Adapters can reach 300 meters at lease, but the actual distance may vary due to the environment.
Section below describes the Mini Powerline Adapter‟s LED indicators, physical interface and hardware connection mechanism.
2.2 LED Indicator
The LED i ndicator displays information about the device‟s status.
Item
Power LED
Powerline LED
Status
Off
On
Power is off.
Power is on.
Indication
Flashing The Adapter is in power-saving Mode.
Off
The Adapter has not connected to Powerline network or is in power-saving Mode.
2
TL-PA211 AV200 Mini Powerline Adapter
Ethernet LED
On The Adapter has connected to a Powerline network.
Flashing The Adapter is transmitting or receiving data.
Off
The Ethernet port is not connected to a device or the device is power off.
On The Ethernet port is linked, but there is no activity.
Flashing Data is being transmitted through the Ethernet port
Note:
5 minutes later since the device connected to the Homeplug is powered off, the Homeplug will switch to
Power-saving Mode automatically.
2.3 Physical Interface
There are four physical interfaces on this Mini Powerline Adapter.
Pair
Interface
Ethernet
Power Plug
Description
One 10/100Mbps Ethernet port connected to PC LAN card or broadband device
Power Plug connected to any 100V ~ 240V AC power socket
Press and hold the Pair button for about 3 to 8 seconds, then release it. The
Power LED will begin flashing.
Note:
1. If you press the Pair button for more than 10 seconds, the Powerline Adapter will leave the network which it is associated with and its network name assumes a random value. The Power LED turns off when it disconnects from the Powerline network.
2. For detail information about the Pair button, please refer to Charpter 5 Advanced Feature:How to
3
TL-PA211 AV200 Mini Powerline Adapter
Use the Push buttons
2.4 Hardware Connection
– Computer
For those computers you wish to be networked by Mini Powerline Adapter, each of the computers must be properly connected with a Mini Powerline Adapter through an Ethernet (RJ-45) cable.
Following are the steps to properly connect the Mini Powerline Adapter to your computer:
1． Connect the provided Ethernet (RJ45) cable to the Mini Powerline Adapter‟s Ethernet port.
2． Connect the other end of the Ethernet (RJ45) cable to you computer‟s LAN port.
3． Plug the Mini Powerline Adapter into a wall socket next to the computer.
4． Turn on your computer.
5． Check and confirm that the Power LED and are ON.
The hardware connection mechanism is shown below:
Ethernet LED on the Mini Powerline Adapter
2.5 Hardware Connection – Internet
This section describes how to connect the Mini Powerline Adapter into your existing ADSL broadband connection via ADSL Ethernet port. Follow the procedures describe below to connect the Mini Powerline
Adapter to your ADSL broadband connection:
1． Connect the provided Ethernet (RJ45) cable to the Mini Powerline Adapter‟s Ethernet port.
2． Connect the other end of the Ethernet (RJ-45) cable to an available Ethernet port of your ADSL broadband Router.
3． Plug the Mini Powerline Adapter into a wall socket next to the computer.
4． Turn on your computer.
5． Check and confirm that the Power LED, Ethernet LED, and Powerline LED on the
Mini Powerline Adapter are ON.
4
The hardware connection mechanism is shown below:
TL-PA211 AV200 Mini Powerline Adapter
Note:
Do not connect the Powerline adapter to an extension lead, power strip, extension cord, surge protector as this may degrade the network performance.
5
TL-PA211 AV200 Mini Powerline Adapter
Chapter 3 Installing Management Utility
Please verify that no other Mini Powerline Adapter or any Encryption Management Utilities are installed before installing the provided software. If other Powerline Utilities are installed, uninstall them and restart your personal computer before installing this provided software.
Note:
Please make sure that you have installed the WinPcap (the version of which should be beyond 4.1.1 inclusive) on your computer before installing the Management Utility. The WinPcap can be found on the provided resource CD.
Take the following procedures to properly installing the provided Management Utility:
Step 1: Insert the resource CD into your CD-ROM drive, and then the following Setup Wizard will automatically pop up on your computer‟s screen.
Step 2: Click Management Utility and the program installation process will carry out and copy all the necessary files to your system.
6
TL-PA211 AV200 Mini Powerline Adapter
7
TL-PA211 AV200 Mini Powerline Adapter
8
TL-PA211 AV200 Mini Powerline Adapter
Step 2: After the installation, a shortcut to the “TL-PA211 Powerline Utility” application icon is provided on the windows desktop.
9
TL-PA211 AV200 Mini Powerline Adapter
Chapter 4 Using The Management Utility
After you‟d successfully installed the Mini Powerline Adapter hardware and Management Utility software, you can setup or configure the devices according to your need.
This Mini Powerline Adapter Configuration Utility enables the users to identify powerline devices on the powerline network, measures data rate performance, ensures privacy and performs diagnostics by setting user defined secure powerline networks.
Double click on the “TL-PA211 Powerline Utility” from your windows desktop, the following screen display. This Management Utility consists of a set of five property sheets, viz., “Main”, “Privacy”,
“QoS”, “Diagnostics” and “About”.
4.1 Main
The Main tab shows all the Mini Powerline Adapters that are logically connected to the current computer where the Management Utility is running.
10
TL-PA211 AV200 Mini Powerline Adapter
Local Device(s) on your computer: This shows all local Powerline Ethernet Adapter found connected to the computer‟s LAN card. In most cases, only one device will display in this panel.
Click and select the local device shown on the screen then click “Connect” tab to manage the
Powerline Ethernet Adapter. The status message will be shown above the “Connect” button indicates that your PC is connected to the same device. Once the chosen Powerline Ethernet
Adapter is properly connected, this Management Utility will automatically scan the power line periodically for any other existing powerline devices. You can upgrade the version of firmware for the device by clicking the Upgrade Firmware button which is shown as below.
PIB: Parameter Information Block. It contains configuration values that establish device network identity, general capabilities and operational modes.
NVM: None-volatile memory. It is used for upgrading the firmware.
If you want to upgrade the version of firmware for the device, please select appropriate Firmware and PIB files together. New firmware versions and PIB files are posted at www.tp-link.com
and can be downloaded for free.
Note:
The parameter information of PIB will restore to the factory defaults after resetting the PLC.
11
TL-PA211 AV200 Mini Powerline Adapter
To upgrade the device's firmware, follow these instructions:
1. Download PIB file and firmware upgrade file from the TP-LINK website ( www.tp-link.com
).
2. Enter the path name or click Browse… to select the downloaded files on the computer into the corresponding blanks.
3. Click the OK button.
Note:
Do not turn off the device while the firmware is being upgraded. The device will reboot after the
Upgrading has been finished.
“x” Powerline Devices detected: This display all the Mini Powerline Adapter found on the current logical network. “x” shows the number of remote Mini Powerline Adapter discovered by this
Management Utility.
Network Type: Displayed the type of logical network: “Public” or “Private”.
Autoscan: Shows the scanning status (Default is “ON”).
Device Name: Shows the default device name. One may redefine or change the name by clicking on the name and editing in place or by clicking the “Rename” button.
Password: Shows the current password of the Mini Powerline Adapter.
Quality: Shows the quality of the Mini Powerline Adapter connection.
Rate (Mbps): Shows the current transmission rate of the selected Mini Powerline Adapter.
MAC Address: Shows the Mini Powerline Adapter‟s MAC address.
Rename: Click to change the name of the selected Mini Powerline Adapter.
Enter Password : Shows the supplied Mini Powerline Adapter‟s password (Initially left blank). To set the Mini Powerline Adapter password (Which is required when creating a private network), click and select the device shown in the lower panel and click on the “Enter Password” button. Follow the pop-up dialog box to complete your password setting.
Add: Click this button to add a remote Mini Powerline Adapter to your network that is not on the lower panel displayed list. You will advice to locate the passwords for all Mini Powerline Adapter you wish to manage and add them to the local logical network by clicking the “Add” button. Follow the pop-up dialog box to complete your setting.
Scan: Click the “Scan” button to perform an immediate search of the Mini Powerline Adapter connected to the computer. The Management Utility will automatically perform the scanning process and update the display every few seconds by default.
4.1.1 Rename
This Management Utility allows you to change the name of the listed Mini Powerline Adapter. Click and select the Mini Powerline Adapter you wish to change from the list, then click on the “Rename” tab and editing-in-place to change the name.
12
TL-PA211 AV200 Mini Powerline Adapter
4.1.2 Enter Password
To set or change your Mini Powerline Adapter‟s password, click and select the Mini Powerline Adapter you wish to change from the list, then click on the “Enter Password” tab, the following screen display.
Enter your Password (
Please note the format, enter it uppercase
) and click “OK” after setup.
Note:
The Mini Powerline Adapter device must be present on the power line (plugged in) in order for the password to be confirmed and added to the network. If the Mini Powerline Adapter device could not be located, a warning message will be shown.
13
TL-PA211 AV200 Mini Powerline Adapter
4.1.3 Add Device
The following dialog box pop-up when clicking the “Add” button under Main configuration homepage.
The dialog box allows you to enter both the selected device‟s name and password. Noted that the Mini
Powerline Adapter must be present on the power grid in order to activate the set password and added to the local network.
Enter your Device Name and Password (Take note to the password format) and click “OK” after setup.
The following screen display after the naming and password setting process, which is also the
Diagnostics configuration homepage.
14
TL-PA211 AV200 Mini Powerline Adapter
4.1.4 Reset
This Management Utility allows you to reset the Mini Powerline Adapter to its default settings by clicking the Reset button on the Main page.
4.2 Privacy
The Privacy configuration page provides a means for managing the local network and providing additional security for the logical network and also to select the devices that has to be included in the network. All Powerline devices are shipped using a default logical network (network name), which is normally “HomePlugAV”
The Privacy configuration homepage allows you to change the Network Name of the Mini Powerline
Adapter that is currently connected to this computer into a private network. Reset the private network to universal public network by clicking on the “Use Default (Public Network)” or entering/editing
“HomePlugAV” under column of “Private Network Name” is always available.
Note that every Mini Powerline Adapter on your home network MUST have the same Network
Password for connectivity to be established throughout your home.
Note:
Changing the network name to anything other than “HomePlugAV” will show the network type on the
Main configuration screen as “Private”.
15
TL-PA211 AV200 Mini Powerline Adapter
Set Local Device Only: Click this tab to change the network name of the local Mini Powerline
Adapter device only. All Mini Powerline Adapter devices seen on the Main configuration homepage prior to this will be no longer present in the new network, effectively making the local devices not to communicate to the devices which were in the old logical network. Devices previously set up with the same logical network (same network name) will appear in the device list afterward selecting this option.
Set All Devices: The Set All Devices button is used to change the logical network of all devices that appear on the Main configuration homepage whose Device‟s Password had been entered for the same logical network. A dialog window will appear to report the success of this operation. For devices whose device passwords were not entered, this operation will fail and will report a failure message.
4.3 QoS
The third tabbed window, labeled „QoS‟ for Quality of Service, is shown in Figure.
16
TL-PA211 AV200 Mini Powerline Adapter
QoS requirements are different for various data types such as streaming video or music, voice and raw data. To provide higher QoS for streaming data, priority levels can be set using tags at the beginning of data frames. Virtual Local Area Network (Vlan) 802.1p priority tags on Ethernet frames are used to specify 8 (0~7) levels of „user priority‟. Homeplug AV powerline allows for 4 levels of Channel Access
Priority CAP(0-3)). Therefore, the 8 levels of VLAN Ethernet tags must be mapped to the 4 levels of CAP priority, where CAP 3 is the highest priority and CAP 0 is the lowest. CAP 3 priority might be used for voice and network management frames, CAP 2 is used for streaming video-and must while CAP 1 can
CAP 0 are used for data. Mapping VLAN tags to CAP levels is easily done using the VLAM Priority
Mapping function on the QoS tab window.
Simple Application Mapping: The group allows you to choose what type of traffic with the highest user priority you will use your local HomePlug device for by pitching on one of the following three radios.
Please select the radio type according to your demand.
Advanced VLAN Priority Mapping: The group sets VLAN priority to CAP mapping and default priority.
Note that in HomePlug, CAP 3 is the highest priority while CAP 0 is the lowest priority. The values shown in VLAN Tags Priority are the default settings for the first running.
4.4 Diagnostics
The Diagnostics homepage shows the System Information and Remote Device History of all remote devices seen over a period of time which are only readable. Click on the “Diagnostics” tab and the following screen display.
17
TL-PA211 AV200 Mini Powerline Adapter
The Diagnostics information displayed can be saved to a text file. One can email the saved text file to the local supplier when there‟s technical support require or print the saved text file as reference during a technical support conference.
The Upper Panel shows technical data concerning software and hardware present on the host computer which were used to communicate over Mini Powerline Adapter on the Powerline network. It may include the following:
Operating System Platform/Version
Host Network Name
User Name
MAC Address of all NICs (Network interface card) connected to the host
Identify versions of all Driver DLLs and Libraries used (NDIS) and optionally
MAC addresses of all devices connected locally to the host
Click the “Delete” tab when there‟s Mini Powerline Adapter devices no longer part of the network.
The Lower Panel contains a history of all remote Mini Powerline Adapter devices seen on the computer over a certain period of time. All devices that were on the powerline network are listed here along with a few other parameters. Mini Powerline Adapter devices that are active on the current logical network will show a transfer rate in the Rate column; devices on other networks, or devices that may no longer exist are shown with a “?” in the Rate column. The following remote Mini Powerline Adapter devices information is available from the diagnostics screen:
Device Alias Name
Device MAC Address
Device Password
18
TL-PA211 AV200 Mini Powerline Adapter
Device Last known rate
Device Last Known Network name
Date device last seen on the network
The diagnostics information displayed may be saved to a text file for later use, or can be printed for reference for a technical support call. Mini Powerline Adapter devices, which are not part of the network anymore, can be deleted using the delete button. A dialog window pops up with a confirmation message if we try to delete a device whose password has been entered.
4.5 About
The About homepage shows the Management Utility software version.
AutoScan: When it is enabled (Place a check), the Management Utility will automatically scan for
Mini Powerline Adapter devices on the local network every few seconds and updated the scanning information on the Main configuration homepage.
19
TL-PA211 AV200 Mini Powerline Adapter
Chapter 5 Advance Feature: How to Use the Push buttons
5.1 Pair( Secure with 128 bits-AES)
The Homeplug AV standard uses 128-bit AES (Advanced Encryption Standard) to safely transmit data between powerline adapters. For the powerline adapters to communicate with each other they all need to use the same Network Membership Key (NMK). Otherwise, they cannot unscramble the encrypted data sent in the powerline network.
The Pair button allows you to set up a secure powerline connection with other HomePlug AV compliant powerline devices which also support the Pair feature.
5.2 Set Up a Powerline AV Network with the Pair button
You can connect a number of devices on a powerline network, but you can use the Pair button on only two devices at a time.
Create a Powerline network using the Pair button：
Step 1. Press and hold the Pair button of Powerline adapter A for 3 to 8 seconds, the Power LED will start flashing.
Step 2. Press and hold the Pair button of Powerline adapter B for 3 to 8 seconds, the Power LED will start flashing.
(This must be done within 120 seconds after pressing the Pair button of Powerline adapter A.)
Step 3. Wait for about 60 seconds while your Powerline adapter A and B are connecting. The Power
LED on both adapters will stop flashing and become solid light when the connection is made.
20
TL-PA211 AV200 Mini Powerline Adapter
Join an existing Powerline AV Network:
Powerline adapter A and Powerline adapter B form a HomeplugAV Network, Powerline adapter C wants to join this network.
Step 1. Press and hold the Pair button on Powerline adapter C for 3 to 8 seconds.
Step 2. Press and hold the Pair button on Powerline adapter A/B for 3 to 8 seconds.
(This step must be taken within 120 seconds after step 1 is finished.)
Step 3. Wait for about 60 seconds while your Powerline adapters are connecting. The Power LED on
Powerline adapter A/B and C will stop flashing and become solid light when the connection is made.
Note:
The sequence of Step 1 and Step 2 can be exchanged.
Leave an existing Powerline AV Network:
As the figure above shown, Powerline adapter A, B and C have formed a HomeplugAV Network. The user wants to remove one device (Powerline adapter A) from this network.
Step 1. Press and hold the Pair button on Powerline adapter A for at least 10 seconds. Powerline adapter A will reset and restart. (The Power LED of Powerline adapter A will momentarily extinguish during resetting, flash during restarting then illuminate steadily.)
Step 2. Wait for the reset to complete.
21
TL-PA211 AV200 Mini Powerline Adapter
Chapter 6 Appendix A: Troubleshooting Guide
The Troubleshooting Guide provides answers to common problems regarding the Mini Powerline
Adapter.
1. The Power LED does not light up.
Ans. Check the following: a) Make sure that the Mini Powerline Adapter is properly plugged into a power outlet. b) Make sure the power outlet is active (working) by plugging another electric device into it. c) Re-plug the Mini Powerline Adapter to the power outlet again. If the Power LED still failed to light up, contact your local dealer for technical support.
2. The Ethernet LED does not light up.
Ans. Check the following:
1. Make sure that the Ethernet cable (RJ-45) is properly connected to the Mini Powerline
Adapter‟s Ethernet port.
2. Make sure that the other end of the Ethernet cable (RJ-45) is properly connected to the computer LAN card or to you Cable/xDSL Ethernet port.
3. Make sure your computer LAN card is properly installed and configured.
4. Make sure your Cable/xDSL broadband access is working and configured correctly.
5. Contact your local dealer for technical support if the Ethernet LED still failed to lights up after the above procedures.
3. The Powerline LED does not light up.
Ans. Check the following:
1. Double click to enable the Management Utility and click the “Scan” tab under the Main configuration homepage. The Management Utility will automatically detect all other Mini
Powerline Adapter on your power line network.
2. Try to plug a second Mini Powerline Adapter into a near by power outlet and check whether the
Powerline LED lights up or not.
3. Contact your local dealer for technical support if the Powerline LED still failed to lights up after the above procedures.
22
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- 200 Mbit/s 300 m
- Fast Ethernet
- Wi-Fi Wi-Fi 4 (802.11n)
- White
Related manuals
Frequently Answers and Questions
What is the recommended operating temperature for the TP-LINK AV200 Mini Powerline Adapter?
What are the system requirements for using the TP-LINK AV200 Mini Powerline Adapter?
How do I connect the TP-LINK AV200 Mini Powerline Adapter to my computer?
How do I connect the TP-LINK AV200 Mini Powerline Adapter to my existing network?
What is the maximum data rate supported by the TP-LINK AV200 Mini Powerline Adapter?
Does the TP-LINK AV200 Mini Powerline Adapter support encryption?
advertisement