Yamaha FZS10 A(C) motorcycle Owner's Manual
Below you will find brief information for motorcycle FZS10 A(C). The motorcycle FZS10 A(C) has many design features that make it a great motorcycle for the operator as well as a passenger. It is also equipped with a catalytic converter system and an EXUP system. It is important to follow the maintenance schedule recommended in the manual.
Advertisement
Advertisement
LIT-11626-24-61
Read this manual carefully before operating this vehicle.
OWNER’S MANUAL
FZS10A(C)
1CA-28199-11
DIC183
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
EAU10042
Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
INTRODUCTION
EAU10083
Congratulations on your purchase of the Yamaha FZS10A(C). This model is the result of Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields.
This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If you have any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.
The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the recommended maintenance schedules and operating instructions contained within this manual.
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your motorcycle and this manual. If there is any question concerning this manual, please consult a Yamaha dealer.
EWA10011
WARNING
Please read this manual and the “YOU AND YOUR MOTORCYCLE: RIDING TIPS” booklet carefully before operating this motorcycle. Do not attempt to operate this motorcycle until you have attained adequate knowledge of its controls and operating features. Regular inspections and careful maintenance, along with good operating techniques, will help ensure that you safely enjoy the capabilities and reliability of this motorcycle.
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
IMPORTANT MANUAL INFORMATION
EAU10132
Particularly important information is distinguished in this manual by the following notations:
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING
NOTICE
A WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
A NOTICE indicates special precautions that must be taken to avoid damage to the vehicle or other property.
TIP
A TIP provides key information to make procedures easier or clearer.
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
IMPORTANT MANUAL INFORMATION
FZS10A(C)
OWNER’S MANUAL
©2010 by Yamaha Motor Corporation, U.S.A.
1st edition, September 2010
All rights reserved.
Any reprinting or unauthorized use without the written permission of
Yamaha Motor Corporation, U.S.A. is expressly prohibited.
Printed in Japan.
P/N LIT-11626-24-61
EAU10193
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
TABLE OF CONTENTS
LABELS .............................................1-1
SAFETY INFORMATION ..................2-1
DESCRIPTION ..................................3-1
Left view ..........................................3-1
Right view ........................................3-2
Controls and instruments.................3-3
Luggage strap holders ................. 4-20
EXUP system ............................... 4-21
Sidestand ..................................... 4-21
Ignition circuit cut-off system ........ 4-22
PRE-OPERATION CHECKS ............. 5-1
RIDING POINTS................................. 6-1
Starting the engine ......................... 6-1
Shifting ........................................... 6-2
Engine break-in .............................. 6-3
Parking ........................................... 6-4
FUNCTIONS .......................................4-1
Main switch/steering lock ................4-1
Indicator lights and warning lights ............................................4-2
Multi-function meter unit .................4-5
Handlebar switches ........................4-9
Clutch lever ...................................4-10
Shift pedal .....................................4-10
Brake lever ...................................4-11
Brake pedal ..................................4-11
Fuel tank cap ................................4-11
Fuel ...............................................4-12
Fuel tank breather/overflow hose ..........................................4-13
Catalytic converters ......................4-14
Seats ............................................4-15
Storage compartment ...................4-16
Adjusting the front fork ..................4-17
Adjusting the shock absorber assembly ...................................4-19
ADJUSTMENT ................................... 7-1
Owner’s tool kit ............................... 7-2
Periodic maintenance chart for the emission control system ....... 7-3
General maintenance and lubrication chart .......................... 7-5
Removing and installing panels ..... 7-9
Checking the spark plugs ............. 7-10
Canister (for California only) ........ 7-11
Engine oil and oil filter cartridge ... 7-11
Coolant ......................................... 7-14
Replacing the air filter element ..... 7-15
Checking the engine idling speed ........................................ 7-17
Checking the throttle grip free play ........................................... 7-18
Valve clearance ........................... 7-18
Tires ............................................. 7-18
Cast wheels ................................. 7-21
Adjusting the clutch lever free play ........................................... 7-21
Checking the brake lever free play ........................................... 7-22
Brake light switches ..................... 7-22
Checking the front and rear brake pads .......................................... 7-23
Checking the brake fluid level ...... 7-23
Changing the brake fluid .............. 7-24
Drive chain slack .......................... 7-25
Cleaning and lubricating the drive chain .......................... 7-26
Checking and lubricating the cables ................................. 7-27
Checking and lubricating the throttle grip and cable ......... 7-27
Checking and lubricating the brake and shift pedals ........ 7-27
Checking and lubricating the brake and clutch levers ...... 7-28
Checking and lubricating the centerstand and sidestand ....... 7-29
Checking the front fork ................. 7-29
Checking the steering .................. 7-30
Checking the wheel bearings ....... 7-30
Battery ......................................... 7-31
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
Replacing the fuses ......................7-32
Replacing a headlight bulb ...........7-34
Replacing the tail/brake light bulb ...........................................7-35
Replacing a turn signal light bulb ...........................................7-35
Replacing the license plate light bulb ...........................................7-36
Front wheel ...................................7-36
Rear wheel ...................................7-38
Troubleshooting ............................7-39
Troubleshooting charts .................7-41
STORAGE ..........................................8-1
Matte color caution .........................8-1
Care ................................................8-1
Storage ...........................................8-3
SPECIFICATIONS .............................9-1
CONSUMER INFORMATION...........10-1
Identification numbers ..................10-1
Reporting safety defects ...............10-3
Motorcycle noise regulation ..........10-4
Maintenance record ......................10-5
LIMITED WARRANTY ..............10-7
(Y.E.S.) ..................................... 10-9
TABLE OF CONTENTS
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
1
LOCATION OF IMPORTANT LABELS
EAU10384
Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label is available from your Yamaha dealer.
1 2 3,4
1-1
6 5
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
1
NOTICE
Cleaning with alkaline or acid cleaner, gasoline or solvent will damage windshield.
Use neutral detergent.
4B5-2815K-00
3
LOCATION OF IMPORTANT LABELS
2
1
4
5
TIRE INFORMATION
Cold tire normal pressure should be set as follows.
• Up to 90 kg (198 lbs) load
FRONT : 250 kPa, (2.50 kgf/cm²), 36 psi
REAR : 290 kPa, (2.90 kgf/cm²), 42 psi
• 90kg (198 lbs) ~ maximum load
FRONT : 250 kPa, (2.50 kgf/cm²), 36 psi
REAR : 290 kPa, (2.90 kgf/cm²), 42 psi
14B-21668-00
6
1-2
1
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
LOCATION OF IMPORTANT LABELS
1
1-3
U1CA11E0.book Page 4 Thursday, September 23, 2010 11:51 AM
1 California only
LOCATION OF IMPORTANT LABELS
1
1-4
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
2
SAFETY INFORMATION
EAU10287
Be a Responsible Owner
As the vehicle’s owner, you are responsible for the safe and proper operation of your motorcycle.
Motorcycles are single-track vehicles.
Their safe use and operation are dependent upon the use of proper riding techniques as well as the expertise of the operator. Every operator should know the following requirements before riding this motorcycle.
He or she should:
● Obtain thorough instructions from a competent source on all aspects
● of motorcycle operation.
Observe the warnings and maintenance requirements in this Owner’s Manual.
●
●
Obtain qualified training in safe and proper riding techniques.
Obtain professional technical service as indicated in this Owner’s
Manual and/or when made necessary by mechanical conditions.
Safe Riding
Perform the pre-operation checks each time you use the vehicle to make sure it is in safe operating condition. Failure to inspect or maintain the vehicle properly increases the possibility of an accident
or equipment damage. See page 5-1
for a list of pre-operation checks.
● This motorcycle is designed to carry the operator and a passenger.
● The failure of motorists to detect and recognize motorcycles in traffic is the predominating cause of automobile/motorcycle accidents.
Many accidents have been caused by an automobile driver who did not see the motorcycle. Making yourself conspicuous appears to be very effective in reducing the chance of this type of accident.
Therefore:
• Wear a brightly colored jacket.
• Use extra caution when you are approaching and passing through intersections, since intersections are the most likely places for motorcycle accidents to occur.
2-1
●
●
• Ride where other motorists can see you. Avoid riding in another motorist’s blind spot.
Many accidents involve inexperienced operators. In fact, many operators who have been involved in accidents do not even have a current motorcycle license.
• Make sure that you are qualified and that you only lend your motorcycle to other qualified operators.
• Know your skills and limits.
Staying within your limits may help you to avoid an accident.
• We recommend that you practice riding your motorcycle where there is no traffic until you have become thoroughly familiar with the motorcycle and all of its controls.
Many accidents have been caused by error of the motorcycle operator. A typical error made by the operator is veering wide on a turn
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
●
● due to excessive speed or undercornering (insufficient lean angle for the speed).
• Always obey the speed limit and never travel faster than warranted by road and traffic conditions.
• Always signal before turning or changing lanes. Make sure that other motorists can see you.
The posture of the operator and passenger is important for proper control.
• The operator should keep both hands on the handlebar and both feet on the operator footrests during operation to maintain control of the motorcycle.
• The passenger should always hold onto the operator, the seat strap or grab bar, if equipped, with both hands and keep both feet on the passenger footrests.
Never carry a passenger unless he or she can firmly place both feet on the passenger footrests.
Never ride under the influence of alcohol or other drugs.
● This motorcycle is designed for onroad use only. It is not suitable for off-road use.
Protective Apparel
The majority of fatalities from motorcycle accidents are the result of head injuries. The use of a safety helmet is the single most critical factor in the prevention or reduction of head injuries.
●
●
Always wear an approved helmet.
Wear a face shield or goggles.
Wind in your unprotected eyes could contribute to an impairment
●
● of vision that could delay seeing a hazard.
The use of a jacket, heavy boots, trousers, gloves, etc., is effective in preventing or reducing abrasions or lacerations.
Never wear loose-fitting clothes, otherwise they could catch on the
● control levers, footrests, or wheels and cause injury or an accident.
Always wear protective clothing that covers your legs, ankles, and feet. The engine or exhaust system become very hot during or after operation and can cause burns.
2-2
SAFETY INFORMATION
● A passenger should also observe the above precautions.
Avoid Carbon Monoxide Poisoning
All engine exhaust contains carbon monoxide, a deadly gas. Breathing carbon monoxide can cause headaches, dizziness, drowsiness, nausea, confusion, and eventually death.
Carbon Monoxide is a colorless, odorless, tasteless gas which may be present even if you do not see or smell any engine exhaust. Deadly levels of carbon monoxide can collect rapidly and you can quickly be overcome and unable to save yourself. Also, deadly levels of carbon monoxide can linger for hours or days in enclosed or poorly ventilated areas. If you experience any symptoms of carbon monoxide poisoning, leave the area immediately, get fresh air, and SEEK MEDICAL TREAT-
MENT.
● Do not run engine indoors. Even if you try to ventilate engine exhaust with fans or open windows and doors, carbon monoxide can rapidly reach dangerous levels.
2
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
2
SAFETY INFORMATION
●
●
Do not run engine in poorly ventilated or partially enclosed areas such as barns, garages, or carports.
Do not run engine outdoors where engine exhaust can be drawn into a building through openings such as windows and doors.
Loading
Adding accessories or cargo to your motorcycle can adversely affect stability and handling if the weight distribution of the motorcycle is changed. To avoid the possibility of an accident, use extreme caution when adding cargo or accessories to your motorcycle. Use extra care when riding a motorcycle that has added cargo or accessories.
Here, along with the information about accessories below, are some general guidelines to follow if loading cargo to your motorcycle:
The total weight of the operator, passenger, accessories and cargo must not exceed the maximum load limit.
Operation of an overloaded vehicle could cause an accident.
Maximum load:
FZS10A 190 kg (419 lb)
FZS10AC 189 kg (417 lb)
When loading within this weight limit, keep the following in mind:
● Cargo and accessory weight should be kept as low and close to the motorcycle as possible. Securely pack your heaviest items as close to the center of the vehicle as
● possible and make sure to distribute the weight as evenly as possible on both sides of the motorcycle to minimize imbalance or instability.
Shifting weights can create a sudden imbalance. Make sure that accessories and cargo are securely attached to the motorcycle before riding. Check accessory mounts and cargo restraints frequently.
• Properly adjust the suspension for your load (suspension-adjustable models only), and check the condition and pressure of your tires.
●
• Never attach any large or heavy items to the handlebar, front fork, or front fender. These items, including such cargo as sleeping bags, duffel bags, or tents, can create unstable handling or a slow steering response.
This vehicle is not designed to pull a trailer or to be attached to a sidecar.
Genuine Yamaha Accessories
Choosing accessories for your vehicle is an important decision. Genuine
Yamaha accessories, which are available only from a Yamaha dealer, have been designed, tested, and approved by Yamaha for use on your vehicle.
Many companies with no connection to
Yamaha manufacture parts and accessories or offer other modifications for
Yamaha vehicles. Yamaha is not in a position to test the products that these aftermarket companies produce.
Therefore, Yamaha can neither endorse nor recommend the use of accessories not sold by Yamaha or
2-3
U1CA11E0.book Page 4 Thursday, September 23, 2010 11:51 AM modifications not specifically recommended by Yamaha, even if sold and installed by a Yamaha dealer.
Aftermarket Parts, Accessories, and
Modifications
While you may find aftermarket products similar in design and quality to genuine Yamaha accessories, recognize that some aftermarket accessories or modifications are not suitable because of potential safety hazards to you or others. Installing aftermarket products or having other modifications performed to your vehicle that change any of the vehicle’s design or operation characteristics can put you and others at greater risk of serious injury or death.
You are responsible for injuries related to changes in the vehicle.
Keep the following guidelines in mind, as well as those provided under “Loading” when mounting accessories.
● Never install accessories or carry cargo that would impair the performance of your motorcycle. Carefully inspect the accessory before using it to make sure that it does not in any way reduce ground
SAFETY INFORMATION clearance or cornering clearance, limit suspension travel, steering travel or control operation, or obscure lights or reflectors.
• Accessories fitted to the handlebar or the front fork area can create instability due to improper weight distribution or aerodynamic changes. If accessories are added to the handlebar or front fork area, they must be as lightweight as possible and should be kept to a minimum.
• Bulky or large accessories may seriously affect the stability of the motorcycle due to aerodynamic effects. Wind may attempt to lift the motorcycle, or the motorcycle may become unstable in cross winds. These accessories may also cause instability when passing or being passed by large vehicles.
• Certain accessories can displace the operator from his or her normal riding position. This improper position limits the freedom of movement of the opera-
● tor and may limit control ability, therefore, such accessories are not recommended.
Use caution when adding electrical accessories. If electrical accessories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause a dangerous loss of lights or engine power.
Aftermarket Tires and Rims
The tires and rims that came with your motorcycle were designed to match the performance capabilities and to provide the best combination of handling, braking, and comfort. Other tires, rims, sizes, and combinations may not be
appropriate. Refer to page 7-18 for tire
specifications and more information on replacing your tires.
Transporting the Motorcycle
Be sure to observe following instructions before transporting the motorcycle in another vehicle.
● Remove all loose items from the motorcycle.
2
2-4
U1CA11E0.book Page 5 Thursday, September 23, 2010 11:51 AM
2
SAFETY INFORMATION
●
●
●
●
●
Check that the fuel cock (if equipped) is in the “OFF” position and that there are no fuel leaks.
Point the front wheel straight ahead on the trailer or in the truck bed, and choke it in a rail to prevent movement.
Shift the transmission in gear (for models with a manual transmission).
Secure the motorcycle with tiedowns or suitable straps that are attached to solid parts of the motorcycle, such as the frame or upper front fork triple clamp (and not, for example, to rubber-mounted handlebars or turn signals, or parts that could break). Choose the location for the straps carefully so the straps will not rub against painted surfaces during transport.
The suspension should be compressed somewhat by the tiedowns, if possible, so that the motorcycle will not bounce excessively during transport.
2-5
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
Left view
DESCRIPTION
EAU10410
3
1. Front fork spring preload adjusting bolt (page 4-17)
2. Front fork compression damping force adjusting screw (page 4-17)
3. Air filter element (page 7-15)
5. Fuel injection system fuse (page 7-32)
6. Storage compartment (page 4-16)
7. Passenger seat lock (page 4-15)
8. Shock absorber assembly spring preload adjusting ring (page 4-19)
9. Shock absorber assembly rebound damping force adjusting screw
11.Engine oil drain bolt (page 7-11)
12.Engine oil filter cartridge (page 7-11)
3-1
3
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
DESCRIPTION
Right view
1 2 3 4 5 6 7
12 11
1. Owner’s tool kit (page 7-2)
2. Rider seat lock lever (page 4-15)
5. Rear brake fluid reservoir (page 7-23)
6. Engine oil filler cap (page 7-11)
7. Front fork rebound damping force adjusting screw (page 4-17)
8. Engine oil level check window (page 7-11)
10 9 8
10.Coolant reservoir (page 7-14)
11.Rear brake light switch (page 7-22)
12.Luggage strap holder (page 4-20)
3-2
EAU10420
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
Controls and instruments
1 2 3 4 5 6 7 8
DESCRIPTION
EAU10430
3
2. Left handlebar switches (page 4-9)
3. Main switch/steering lock (page 4-1)
4. Multi-function meter unit (page 4-5)
5. Front brake fluid reservoir (page 7-23)
6. Right handlebar switches (page 4-9)
3-3
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
4
INSTRUMENT AND CONTROL FUNCTIONS
Main switch/steering lock
EAU10460 EAU10661
OFF
All electrical systems are off. The key can be removed.
EWA10061
WARNING
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving.
Otherwise the electrical systems will be switched off, which may result in loss of control or an accident.
To lock the steering
1 2
The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below.
EAU10683
LOCK
The steering is locked, and all electrical systems are off. The key can be removed.
EAU26900
ON
All electrical circuits are supplied with power, and the meter lighting, taillight, license plate light and position lights come on, and the engine can be started. The key cannot be removed.
TIP
The headlights come on automatically when the engine is started and stay on until the key is turned to “OFF”, even if the engine stalls.
1. Push.
2. Turn.
1. Turn the handlebars all the way to the left.
2. Push the key in from the “OFF” position, and then turn it to “LOCK” while still pushing it.
3. Remove the key.
4-1
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
To unlock the steering
1 2
INSTRUMENT AND CONTROL FUNCTIONS
EAU49391
Indicator lights and warning lights
EAU11060
Neutral indicator light “ ”
This indicator light comes on when the transmission is in the neutral position.
High beam indicator light “ ”
EAU11080
This indicator light comes on when the high beam of the headlight is switched on.
1. Push.
2. Turn.
Push the key in, and then turn it to
“OFF” while still pushing it.
1. Left turn signal indicator light “ ”
2. Right turn signal indicator light “ ”
3. Neutral indicator light “ ”
4. High beam indicator light “ ”
5. Engine trouble warning light “
6. Oil level warning light “ ”
”
7. Coolant temperature warning light “ ”
EAU11030
Turn signal indicator lights “ ” and “ ”
The corresponding indicator light flashes when the turn signal switch is pushed to the left or right.
EAU11254
Oil level warning light “ ”
This warning light comes on if the engine oil level is low.
The electrical circuit of the warning light can be checked by turning the key to
“ON”. The warning light should come on for a few seconds, and then go off.
If the warning light does not come on initially when the key is turned to “ON”, or if the warning light remains on, have a Yamaha dealer check the electrical circuit.
TIP
● Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction.
4-2
4
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
4
INSTRUMENT AND CONTROL FUNCTIONS
● This model is also equipped with a self-diagnosis device for the oil level detection circuit. If a problem is detected in the oil level detection circuit, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5 seconds. If this occurs, have a Yamaha dealer check the vehicle.
ECA10021
NOTICE
Do not continue to operate the engine if it is overheating.
TIP
●
●
For radiator-fan-equipped vehicles, the radiator fan(s) automatically switch on or off according to the coolant temperature in the radiator.
If the engine overheats, see page
7-41 for further instructions.
EAU11428
Coolant temperature warning light “ ”
This warning light comes on if the engine overheats. If this occurs, stop the engine immediately and allow the engine to cool.
The electrical circuit of the warning light can be checked by turning the key to
“ON”. The warning light should come on for a few seconds, and then go off.
If the warning light does not come on initially when the key is turned to “ON”, or if the warning light remains on, have a Yamaha dealer check the electrical circuit.
4-3
U1CA11E0.book Page 4 Thursday, September 23, 2010 11:51 AM
Under 39 °C
(Under 103 °F)
40–116 °C
(104–242 °F)
117–134 °C
(243–274 °F)
Above 135 °C
(Above 275 °F)
Display
INSTRUMENT AND CONTROL FUNCTIONS
Conditions What to do
Message “Lo” is displayed.
OK. Go ahead with riding.
Coolant temperature is displayed.
OK. Go ahead with riding.
Coolant temperature flashes.
Warning light comes on.
Stop the vehicle and allow it to idle until the coolant temperature goes down.
If the temperature does not go down,
stop the engine. (See page 7-41.)
4
Message “HI” flashes.
Warning light comes on.
Stop the engine and allow it to cool.
4-4
U1CA11E0.book Page 5 Thursday, September 23, 2010 11:51 AM
4
INSTRUMENT AND CONTROL FUNCTIONS
EAU11534
Engine trouble warning light “ ”
This warning light comes on or flashes if a problem is detected in the electrical circuit monitoring the engine. If this occurs, have a Yamaha dealer check the
self-diagnosis system. (See page 4-8
for an explanation of the self-diagnosis device.)
The electrical circuit of the warning light can be checked by turning the key to
“ON”. The warning light should come on for a few seconds, and then go off.
If the warning light does not come on initially when the key is turned to “ON”, or if the warning light remains on, have a Yamaha dealer check the electrical circuit.
Multi-function meter unit
EAU4017B
1. Coolant temperature display/air intake temperature display
2. Speedometer
3. Tachometer
4. Odometer/tripmeter/fuel reserve tripmeter
5. “SELECT” button
6. “RESET” button
7. Clock
8. Fuel meter
EWA12422
WARNING
Be sure to stop the vehicle before making any setting changes to the multi-function meter unit. Changing settings while riding can distract the operator and increase the risk of an accident.
●
●
●
●
●
●
The multi-function meter unit is equipped with the following:
●
●
●
● a speedometer a tachometer an odometer two tripmeters (which show the distance traveled since they were last set to zero)
● a fuel reserve tripmeter (which shows the distance traveled since the left segment of the fuel meter started flashing) a clock a fuel meter a coolant temperature display an air intake temperature display a self-diagnosis device an LCD and tachometer brightness control mode
TIP
● Be sure to turn the key to “ON” before using the “SELECT” and “RE-
SET” buttons except for setting the
LCD and tachometer brightness control mode.
4-5
U1CA11E0.book Page 6 Thursday, September 23, 2010 11:51 AM
Tachometer Clock
INSTRUMENT AND CONTROL FUNCTIONS
● To switch the speedometer and odometer/tripmeter displays between kilometers and miles, press the “SELECT” button for at least one second.
ECA10031
NOTICE
Do not operate the engine in the tachometer red zone.
Red zone: 12000 r/min and above
2. Push the “SELECT” button and
“RESET” button together for at least two seconds.
3. When the hour digits start flashing, push the “RESET” button to set the hours.
4. Push the “SELECT” button, and the minute digits will start flashing.
5. Push the “RESET” button to set the minutes.
6. Push the “SELECT” button and then release it to start the clock.
Odometer and tripmeter modes
4
1. Tachometer
2. Tachometer red zone
The electric tachometer allows the rider to monitor the engine speed and keep it within the ideal power range.
When the key is turned to “ON”, the tachometer needle will sweep once across the r/min range and then return to zero r/min in order to test the electrical circuit.
1. Clock
The clock displays when the key is turned to “ON”. In addition, the clock can be displayed for 10 seconds by pushing the “SELECT” button when the main switch is in the “OFF” or “LOCK” position.
To set the clock
1. Turn the key to “ON”.
1. Odometer/tripmeter/fuel reserve tripmeter
4-6
U1CA11E0.book Page 7 Thursday, September 23, 2010 11:51 AM
4
INSTRUMENT AND CONTROL FUNCTIONS
Push the “SELECT” button to switch the display between the odometer mode “ODO” and the tripmeter modes
“TRIP A” and “TRIP B” in the following order:
TRIP A → TRIP B → ODO → TRIP A
When the fuel amount in the fuel tank decreases to 3.4 L (0.90 US gal,
0.75 Imp.gal), the left segment of the fuel meter will start flashing, and the odometer display will automatically change to the fuel reserve tripmeter mode “F-TRIP” and start counting the distance traveled from that point. In that case, push the “SELECT” button to switch the display between the various tripmeter and odometer modes in the following order:
F-TRIP → TRIP A → TRIP B → ODO
→ F-TRIP
To reset a tripmeter, select it by pushing the “SELECT” button, and then push the “RESET” button for at least one second. If you do not reset the fuel reserve tripmeter manually, it will reset itself automatically and the display will return to the prior mode after refueling and traveling 5 km (3 mi).
Fuel meter
1. Fuel meter
The fuel meter indicates the amount of fuel in the fuel tank. The display segments of the fuel meter disappear towards “E” (Empty) as the fuel level decreases. When the last segment on the left starts flashing, refuel as soon as possible.
TIP
This fuel meter is equipped with a selfdiagnosis system. If a problem is detected in the electrical circuit, the following cycle will be repeated until the malfunction is corrected: “E” (Empty),
“F” (Full) and symbol “ ” will flash eight times, then go off for approximately 3 seconds. If this occurs, have a
Yamaha dealer check the electrical circuit.
Coolant temperature mode
1. Coolant temperature display
The coolant temperature display indicates the temperature of the coolant.
TIP
When the coolant temperature display is selected, “C” is displayed for one second, and then the coolant temperature is displayed.
ECA10021
NOTICE
Do not continue to operate the engine if it is overheating.
4-7
U1CA11E0.book Page 8 Thursday, September 23, 2010 11:51 AM
Air intake temperature mode
INSTRUMENT AND CONTROL FUNCTIONS
●
●
When the key is turned to “ON”, the coolant temperature is automatically displayed, even if the air intake temperature was displayed prior to turning the key to “OFF”.
When the air intake temperature display is selected, “A” is displayed for one second, and then the air intake temperature is displayed.
If the display indicates any error codes, note the code number, and then have a
Yamaha dealer check the vehicle.
ECA11590
NOTICE
If the display indicates an error code, the vehicle should be checked as soon as possible in order to avoid engine damage.
1. Air intake temperature display
The air intake temperature display indicates the temperature of the air drawn into the air filter case. Turn the key to
“ON”, and push the “RESET” button to switch the coolant temperature display to the air intake temperature display.
Push the “RESET” button again to return to the coolant temperature display.
TIP
● Even if the air intake temperature is set to be displayed, the coolant temperature warning light comes on if the engine overheats.
Self-diagnosis device
1. Error code display
This model is equipped with a self-diagnosis device for various electrical circuits.
If a problem is detected in any of those circuits, the engine trouble warning light will come on and the display will indicate an error code.
4-8
LCD and tachometer brightness control mode
1. Tachometer panel
2. Tachometer needle
3. LCD
4. Brightness level
4
U1CA11E0.book Page 9 Thursday, September 23, 2010 11:51 AM
4
INSTRUMENT AND CONTROL FUNCTIONS
This function allows you to adjust the brightness of the LCD and the tachometer panel and needle to suit the outside lighting conditions.
Handlebar switches
Left
EAU12348 EAU12400
Dimmer switch “ / ”
Set this switch to “ ” for the high beam and to “ ” for the low beam.
To set the brightness
1. Turn the key to “OFF”.
2. Push and hold the “SELECT” button.
3. Turn the key to “ON”, and then release the “SELECT” button after five seconds.
4. Push the “RESET” button to select the desired brightness level.
5. Push the “SELECT” button to confirm the selected brightness level.
The display will return to the prior mode.
1. Dimmer switch “ / ”
2. Turn signal switch “ / ”
3. Horn switch “ ”
4. Hazard switch “ ”
Right
EAU12460
Turn signal switch “ / ”
To signal a right-hand turn, push this switch to “ ”. To signal a left-hand turn, push this switch to “ ”. When released, the switch returns to the center position. To cancel the turn signal lights, push the switch in after it has returned to the center position.
EAU12500
Horn switch “ ”
Press this switch to sound the horn.
EAU12660
Engine stop switch “ / ”
Set this switch to “ ” before starting the engine. Set this switch to “ ” to stop the engine in case of an emergency, such as when the vehicle overturns or when the throttle cable is stuck.
1. Engine stop switch “ / ”
2. Start switch “ ”
4-9
U1CA11E0.book Page 10 Thursday, September 23, 2010 11:51 AM
INSTRUMENT AND CONTROL FUNCTIONS
EAU12871 EAU12711
Start switch “ ”
Push this switch to crank the engine
with the starter. See page 6-1 for start-
ing instructions prior to starting the engine.
Clutch lever
EAU12820
Shift pedal
EAU41700
The engine trouble warning light will come on when the key is turned to “ON” and the start switch is pushed, but this does not indicate a malfunction.
EAU12765
Hazard switch “ ”
With the key in the “ON” position, use this switch to turn on the hazard lights
(simultaneous flashing of all turn signal lights).
The hazard lights are used in case of an emergency or to warn other drivers when your vehicle is stopped where it might be a traffic hazard.
ECA10061
NOTICE
Do not use the hazard lights for an extended length of time with the engine not running, otherwise the battery may discharge.
1. Clutch lever
The clutch lever is located at the left handlebar grip. To disengage the clutch, pull the lever toward the handlebar grip. To engage the clutch, release the lever. The lever should be pulled rapidly and released slowly for smooth clutch operation.
The clutch lever is equipped with a clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
1. Shift pedal
The shift pedal is located on the left side of the motorcycle and is used in combination with the clutch lever when shifting the gears of the 6-speed constant-mesh transmission equipped on this motorcycle.
4
4-10
U1CA11E0.book Page 11 Thursday, September 23, 2010 11:51 AM
INSTRUMENT AND CONTROL FUNCTIONS
EAU26823
Brake lever
The brake lever is located at the right handlebar grip. To apply the front brake, pull the lever toward the handlebar grip.
Brake pedal
EAU12941
Fuel tank cap
EAU13074
4
1. Brake lever
2. Brake lever position adjusting dial
3. “ ” mark
4. Distance between brake lever and handlebar grip
The brake lever is equipped with a brake lever position adjusting dial. To adjust the distance between the brake lever and the handlebar grip, turn the adjusting dial while holding the lever pushed away from the handlebar grip.
Make sure that the appropriate setting on the adjusting dial is aligned with the “ ” mark on the brake lever.
1. Brake pedal
The brake pedal is on the right side of the motorcycle. To apply the rear brake, press down on the brake pedal.
4-11
1. Fuel tank cap lock cover
2. Unlock.
To open the fuel tank cap
Open the fuel tank cap lock cover, insert the key into the lock, and then turn it 1/4 turn clockwise. The lock will be released and the fuel tank cap can be opened.
To close the fuel tank cap
1. Push the fuel tank cap into position with the key inserted in the lock.
2. Turn the key counterclockwise to the original position, remove it, and then close the lock cover.
U1CA11E0.book Page 12 Thursday, September 23, 2010 11:51 AM
INSTRUMENT AND CONTROL FUNCTIONS
TIP
The fuel tank cap cannot be closed unless the key is in the lock. In addition, the key cannot be removed if the cap is not properly closed and locked.
EWA11091
WARNING
Make sure that the fuel tank cap is properly closed after filling fuel.
Leaking fuel is a fire hazard.
EAU13221
Fuel
Make sure there is sufficient gasoline in the tank.
EWA10881
WARNING
Gasoline and gasoline vapors are extremely flammable. To avoid fires and explosions and to reduce the risk of injury when refueling, follow these instructions.
1. Before refueling, turn off the engine and be sure that no one is sitting on the vehicle. Never refuel while smoking, or while in the vicinity of sparks, open flames, or other sources of ignition such as the pilot lights of water heaters and clothes dryers.
2. Do not overfill the fuel tank. When refueling, be sure to insert the pump nozzle into the fuel tank filler hole. Stop filling when the fuel reaches the bottom of the filler tube. Because fuel expands when it heats up, heat from the engine or the sun can cause fuel to spill out of the fuel tank.
1. Fuel tank filler tube
2. Maximum fuel level
3. Wipe up any spilled fuel immediately. NOTICE: Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts.
[ECA10071]
4. Be sure to securely close the fuel tank cap.
EWA15151
WARNING
Gasoline is poisonous and can cause injury or death. Handle gasoline with care. Never siphon gasoline by mouth. If you should swallow some gasoline or inhale a lot of gasoline vapor, or get some gasoline in your eyes, see your doctor immedi-
4-12
4
U1CA11E0.book Page 13 Thursday, September 23, 2010 11:51 AM
4
INSTRUMENT AND CONTROL FUNCTIONS ately. If gasoline spills on your skin, wash with soap and water. If gasoline spills on your clothing, change your clothes.
Recommended fuel:
Unleaded gasoline only
Fuel tank capacity:
18.0 L (4.76 US gal, 3.96 Imp.gal)
Fuel reserve amount:
3.4 L (0.90 US gal, 0.75 Imp.gal)
EAU13313 um unleaded fuel. Use of unleaded fuel will extend spark plug life and reduce maintenance costs.
Gasohol
There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing ethanol can be used if the ethanol content does not exceed 10% (E10). Gasohol containing methanol is not recommended by Yamaha because it can cause damage to the fuel system or vehicle performance problems.
ECA11400
NOTICE
Use only unleaded gasoline. The use of leaded gasoline will cause severe damage to internal engine parts, such as the valves and piston rings, as well as to the exhaust system.
Your Yamaha engine has been designed to use regular unleaded gasoline with a pump octane number
[(R+M)/2] of 86 or higher, or a research octane number of 91 or higher. If knocking (or pinging) occurs, use a gasoline of a different brand or premi-
EAU48790
Fuel tank breather/overflow hose
1. Fuel tank breather hose
2. Original position (paint mark)
3. Fuel tank overflow hose
3
2
1
TIP
For California: See page 7-11 for
breather hose information.
Before operating the motorcycle:
● Check the fuel tank breather/over-
● flow hose connection.
Check the fuel tank breather/over-
● flow hose for cracks or damage, and replace it if damaged.
Make sure that the end of the fuel tank breather/overflow hose is not blocked, and clean it if necessary.
4-13
U1CA11E0.book Page 14 Thursday, September 23, 2010 11:51 AM
INSTRUMENT AND CONTROL FUNCTIONS
● Make sure that the end of the fuel tank breather/overflow hose is positioned inside of the clamp.
EAU13445
Catalytic converters
This vehicle is equipped with catalytic converters in the exhaust system.
EWA10862
WARNING
The exhaust system is hot after operation. To prevent a fire hazard or burns:
● Do not park the vehicle near
● possible fire hazards such as grass or other materials that easily burn.
Park the vehicle in a place
●
● where pedestrians or children are not likely to touch the hot exhaust system.
Make sure that the exhaust system has cooled down before doing any maintenance work.
Do not allow the engine to idle more than a few minutes. Long idling can cause a build-up of heat.
ECA10701
NOTICE
Use only unleaded gasoline. The use of leaded gasoline will cause unrepairable damage to the catalytic converter.
4
4-14
U1CA11E0.book Page 15 Thursday, September 23, 2010 11:51 AM
INSTRUMENT AND CONTROL FUNCTIONS
EAU39322
Seats
Passenger seat
To remove the passenger seat
1. Insert the key into the seat lock, and then turn it counterclockwise.
4
1. Passenger seat lock
2. Unlock.
2. Pull the passenger seat forward, and then lift it up.
2. Remove the key.
1. Rider seat lock lever
Rider seat
To remove the rider seat
1. Remove the passenger seat.
2. Push the rider seat lock lever, located under the back of the rider seat, to the right as shown, and then pull the seat off.
To install the rider seat
1. Insert the projection on the front of the rider seat into the seat holder as shown, and then push the rear of the seat down to lock it in place.
To install the passenger seat
1. Place the passenger seat in the original position, and then push the rear of the seat down to lock it in place.
1. Projection
2. Seat holder
2. Install the passenger seat.
4-15
U1CA11E0.book Page 16 Thursday, September 23, 2010 11:51 AM
INSTRUMENT AND CONTROL FUNCTIONS
TIP
Make sure that the seats are properly secured before riding.
Storage compartment
1
EAU14463 ● Do not exceed the maximum load of FZS10A 190 kg (419 lb)
FZS10AC 189 kg (417 lb) for the vehicle.
1. Storage compartment
The storage compartment is located
under the passenger seat. (See page
When storing the Owner’s Manual or other documents in the storage compartment, be sure to wrap them in a plastic bag so that they will not get wet.
When washing the vehicle, be careful not to let any water enter the storage compartment.
EWA10961
WARNING
● Do not exceed the load limit of 3 kg (7 lb) for the storage compartment.
4-16
4
U1CA11E0.book Page 17 Thursday, September 23, 2010 11:51 AM
4
INSTRUMENT AND CONTROL FUNCTIONS
EAU39335
Adjusting the front fork
EWA14670
WARNING
Always adjust the spring preload on both fork legs equally, otherwise poor handling and loss of stability may result.
Each front fork leg is equipped with a spring preload adjusting bolt, the right front fork leg is equipped with a rebound damping force adjusting screw and the left front fork leg with a compression damping force adjusting screw.
ECA10101
NOTICE
To avoid damaging the mechanism, do not attempt to turn beyond the maximum or minimum settings.
load and thereby soften the suspension, turn the adjusting bolt on each fork leg in direction (b).
1. Spring preload adjusting bolt
Align the appropriate groove on the adjusting mechanism with the top of the front fork cap bolt.
Spring preload setting:
Minimum (soft):
8
Standard:
5.5
Maximum (hard):
0
Rebound damping force
The rebound damping force is adjusted on the right front fork leg only. To increase the rebound damping force and thereby harden the rebound damping, turn the adjusting screw in direction (a).
To decrease the rebound damping force and thereby soften the rebound damping, turn the adjusting screw in direction (b).
TIP
Be sure to perform this adjustment on the right front fork leg.
Spring preload
To increase the spring preload and thereby harden the suspension, turn the adjusting bolt on each fork leg in direction (a). To decrease the spring pre-
1. Current setting
2. Front fork cap bolt
4-17
U1CA11E0.book Page 18 Thursday, September 23, 2010 11:51 AM
INSTRUMENT AND CONTROL FUNCTIONS pression damping force and thereby soften the compression damping, turn the adjusting screw in direction (b).
TIP
Be sure to perform this adjustment on the left front fork leg.
TIP
Although the total number of clicks of a damping force adjusting mechanism may not exactly match the above specifications due to small differences in production, the actual number of clicks always represents the entire adjusting range. To obtain a precise adjustment, it would be advisable to check the number of clicks of each damping force adjusting mechanism and to modify the specifications as necessary.
1. Rebound damping force adjusting screw
Rebound damping setting:
Minimum (soft):
26 click(s) in direction (b)*
Standard:
18 click(s) in direction (b)*
Maximum (hard):
1 click(s) in direction (b)*
* With the adjusting screw fully turned in direction (a)
Compression damping force
The compression damping force is adjusted on the left front fork leg only. To increase the compression damping force and thereby harden the compression damping, turn the adjusting screw in direction (a). To decrease the com-
1. Compression damping force adjusting screw
Compression damping setting:
Minimum (soft):
26 click(s) in direction (b)*
Standard:
5 click(s) in direction (b)*
Maximum (hard):
1 click(s) in direction (b)*
* With the adjusting screw fully turned in direction (a)
4
4-18
U1CA11E0.book Page 19 Thursday, September 23, 2010 11:51 AM
4
INSTRUMENT AND CONTROL FUNCTIONS
EAU39345
Adjusting the shock absorber assembly
This shock absorber assembly is equipped with a spring preload adjusting ring and a rebound damping force adjusting screw.
ECA10101
NOTICE
To avoid damaging the mechanism, do not attempt to turn beyond the maximum or minimum settings.
Spring preload
To increase the spring preload and thereby harden the suspension, turn the adjusting ring in direction (a). To decrease the spring preload and thereby soften the suspension, turn the adjusting ring in direction (b).
1
(a)
2
(b)
3
4
1 2 3 4
5 6 7
1. Spring preload adjusting ring
2. Special wrench
3. Extension bar
4. Position indicator
●
●
Align the appropriate notch in the adjusting ring with the position indicator on the shock absorber.
Use the special wrench and the extension bar included in the owner’s tool kit to make the adjustment.
Rebound damping force
To increase the rebound damping force and thereby harden the rebound damping, turn the adjusting screw in direction
(a). To decrease the rebound damping force and thereby soften the rebound damping, turn the adjusting screw in direction (b).
1. Rebound damping force adjusting screw
Spring preload setting:
Minimum (soft):
1
Standard:
3
Maximum (hard):
7
Rebound damping setting:
Minimum (soft):
12 click(s) in direction (b)*
Standard:
8 click(s) in direction (b)*
Maximum (hard):
1 click(s) in direction (b)*
* With the adjusting screw fully turned in direction (a)
4-19
U1CA11E0.book Page 20 Thursday, September 23, 2010 11:51 AM
TIP
To obtain a precise adjustment, it is advisable to check the actual total number of clicks or turns of the damping force adjusting mechanism. This adjustment range may not exactly match the specifications listed due to small differences in production.
EWA10221
WARNING
This shock absorber assembly contains highly pressurized nitrogen gas. Read and understand the following information before handling the shock absorber assembly.
● Do not tamper with or attempt to
● open the cylinder assembly.
Do not subject the shock absorber assembly to an open flame or other high heat source.
●
This may cause the unit to explode due to excessive gas pressure.
Do not deform or damage the cylinder in any way. Cylinder damage will result in poor damping performance.
INSTRUMENT AND CONTROL FUNCTIONS
● Do not dispose of a damaged or worn-out shock absorber assembly yourself. Take the shock absorber assembly to a Yamaha dealer for any service.
Luggage strap holders
EAU15151
1. Luggage strap holder
There is a luggage strap holder on each passenger footrest.
4
4-20
U1CA11E0.book Page 21 Thursday, September 23, 2010 11:51 AM
4
INSTRUMENT AND CONTROL FUNCTIONS
EAU41941
EXUP system
This model is equipped with Yamaha’s
EXUP (EXhaust Ultimate Power valve) system. This system boosts engine power by means of a valve that regulates the inner diameter of the exhaust pipe. The EXUP system valve is constantly adjusted in accordance with the engine speed by a computer-controlled servomotor.
ECA15610
NOTICE
The EXUP system has been set and extensively tested at the Yamaha factory. Changing these settings without sufficient technical knowledge may result in poor performance of or damage to the engine.
EAU15304
Sidestand
The sidestand is located on the left side of the frame. Raise the sidestand or lower it with your foot while holding the vehicle upright.
TIP
The built-in sidestand switch is part of the ignition circuit cut-off system, which cuts the ignition in certain situations.
(See page 4-22 for an explanation of
the ignition circuit cut-off system.)
EWA10241
WARNING
The vehicle must not be ridden with the sidestand down, or if the sidestand cannot be properly moved up
(or does not stay up), otherwise the sidestand could contact the ground and distract the operator, resulting in a possible loss of control.
Yamaha’s ignition circuit cut-off system has been designed to assist the operator in fulfilling the responsibility of raising the sidestand before starting off. Therefore, check this system regularly and have a
Yamaha dealer repair it if it does not function properly.
4-21
U1CA11E0.book Page 22 Thursday, September 23, 2010 11:51 AM
INSTRUMENT AND CONTROL FUNCTIONS
EAU44902
Ignition circuit cut-off system
The ignition circuit cut-off system (comprising the sidestand switch, clutch switch and neutral switch) has the following functions.
● It prevents starting when the transmission is in gear and the side-
● stand is up, but the clutch lever is not pulled.
It prevents starting when the transmission is in gear and the clutch le-
● ver is pulled, but the sidestand is still down.
It cuts the running engine when the transmission is in gear and the sidestand is moved down.
Periodically check the operation of the ignition circuit cut-off system according to the following procedure.
4
4-22
U1CA11E0.book Page 23 Thursday, September 23, 2010 11:51 AM
4
INSTRUMENT AND CONTROL FUNCTIONS
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is set to “
3. Turn the key on.
4. Shift the transmission into the neutral position.
5. Push the start switch.
Does the engine start?
”.
YES
With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.
Does the engine stall?
YES
NO
NO
After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.
Does the engine start?
YES NO
The system is OK. The motorcycle can be ridden.
WARNING
•
The vehicle must be placed on the center-
stand during this inspection.
•
If a malfunction is noted, have a Yamaha
dealer check the system before riding.
The neutral switch may not be working correctly.
The motorcycle should not be ridden until checked by a Yamaha dealer.
The sidestand switch may not be working correctly.
The motorcycle should not be ridden until checked by a Yamaha dealer.
The clutch switch may not be working correctly.
The motorcycle should not be ridden until checked by a Yamaha dealer.
4-23
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
FOR YOUR SAFETY – PRE-OPERATION CHECKS
EAU15596
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection and maintenance procedures and schedules described in the Owner’s Manual.
EWA11151
WARNING
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage.
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
ITEM CHECKS PAGE
Fuel
Engine oil
Coolant
Front brake
• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.
• Check fuel tank breather/overflow hose for obstructions, cracks or damage, and check hose connection.
• Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.
• Check coolant level in reservoir.
• If necessary, add recommended coolant to specified level.
• Check cooling system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
5
5-1
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
5
FOR YOUR SAFETY – PRE-OPERATION CHECKS
ITEM
Rear brake
Clutch
Throttle grip
Control cables
Drive chain
Wheels and tires
Brake and shift pedals
Brake and clutch levers
Centerstand, sidestand
CHECKS
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Check operation.
• Lubricate cable if necessary.
• Check lever free play.
• Adjust if necessary.
• Make sure that operation is smooth.
• Check throttle grip free play.
• If necessary, have Yamaha dealer adjust throttle grip free play and lubricate cable and grip housing.
• Make sure that operation is smooth.
• Lubricate if necessary.
• Check chain slack.
• Adjust if necessary.
• Check chain condition.
• Lubricate if necessary.
• Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary.
• Make sure that operation is smooth.
• Lubricate pedal pivoting points if necessary.
• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.
• Make sure that operation is smooth.
• Lubricate pivots if necessary.
5-2
PAGE
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
FOR YOUR SAFETY – PRE-OPERATION CHECKS
ITEM
Chassis fasteners
Instruments, lights, signals and switches
Sidestand switch
CHECKS
• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.
• Check operation.
• Correct if necessary.
• Check operation of ignition circuit cut-off system.
• If system is not working correctly, have Yamaha dealer check vehicle.
PAGE
—
—
5
5-3
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
6
OPERATION AND IMPORTANT RIDING POINTS
EAU15951
Read the Owner’s Manual carefully to become familiar with all controls. If there is a control or function you do not understand, ask your Yamaha dealer.
EWA10271
WARNING
Failure to familiarize yourself with the controls can lead to loss of control, which could cause an accident or injury.
TIP
This model is equipped with:
● a lean angle sensor to stop the engine in case of a turnover. In this case, the multi-function meter unit indicates error code 30, but this is not a malfunction. Turn the key to
“OFF” and then to “ON” to clear the error code. Failing to do so will pre-
● vent the engine from starting even though the engine will crank when pushing the start switch.
an engine auto-stop system. The engine stops automatically if left idling for 20 minutes. In this case, the multi-function meter unit indicates error code 70, but this is not a malfunction. Push the start switch to clear the error code and to restart the engine.
EAU47150 EAU40199
Starting the engine
In order for the ignition circuit cut-off system to enable starting, one of the following conditions must be met.
● The transmission is in the neutral position.
● The transmission is in gear with the clutch lever pulled and the sidestand up.
See page 4-22 for more informa-
tion.
1. Turn the key to “ON” and make sure that the engine stop switch is set to “ ”.
The following warning lights should come on for a few seconds, then go off.
●
●
Oil level warning light
Coolant temperature warning light
● Engine trouble warning light
ECA15484
NOTICE
If a warning light does not come on initially when the key is turned to
“ON”, or if a warning light remains
on, see page 4-2 for the correspond-
ing warning light circuit check.
6-1
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
OPERATION AND IMPORTANT RIDING POINTS
2. Shift the transmission into the neutral position. The neutral indicator light should come on. If not, ask a
Yamaha dealer to check the electrical circuit.
3. Start the engine by pushing the start switch.
If the engine fails to start, release the start switch, wait a few seconds, and then try again. Each starting attempt should be as short as possible to preserve the battery. Do not crank the engine more than 10 seconds on any one attempt.
ECA11042
NOTICE
For maximum engine life, never accelerate hard when the engine is cold!
Shifting
EAU16671
1. Shift pedal
2. Neutral position
Shifting gears lets you control the amount of engine power available for starting off, accelerating, climbing hills, etc.
The gear positions are shown in the illustration.
TIP
To shift the transmission into the neutral position, press the shift pedal down repeatedly until it reaches the end of its travel, and then slightly raise it.
ECA10260
NOTICE
●
●
Even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long distances. The transmission is properly lubricated only when the engine is running. Inadequate lubrication may damage the transmission.
Always use the clutch while changing gears to avoid damaging the engine, transmission, and drive train, which are not designed to withstand the shock of forced shifting.
EAU16681
To start out and accelerate
1. Pull the clutch lever to disengage the clutch.
2. Shift the transmission into first gear. The neutral indicator light should go out.
3. Open the throttle gradually, and at the same time, release the clutch lever slowly.
6-2
6
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
6
OPERATION AND IMPORTANT RIDING POINTS
4. At the recommended shift points shown in the following table, close the throttle, and at the same time, quickly pull the clutch lever in.
5. Shift the transmission into second gear. (Make sure not to shift the transmission into the neutral position.)
6. Open the throttle part way and gradually release the clutch lever.
7. Follow the same procedure when shifting to the next higher gear.
TIP
When shifting gears in normal operating conditions, use the recommended shift points.
EAU16700
To decelerate
1. Apply both the front and the rear brakes to slow the motorcycle.
2. Shift the transmission into first gear when the motorcycle reaches
25 km/h (16 mi/h). If the engine is about to stall or runs very roughly, pull the clutch lever in and use the brakes to stop the motorcycle.
3. Shift the transmission into the neutral position when the motorcycle is almost completely stopped. The neutral indicator light should come on.
EAU16740
Recommended shift points
The recommended shift points during acceleration and deceleration are shown in the table below.
Shift up points:
1st → 2nd: 20 km/h (12 mi/h)
2nd → 3rd: 30 km/h (19 mi/h)
3rd
→ 4th: 40 km/h (25 mi/h)
4th → 5th: 50 km/h (31 mi/h)
5th → 6th: 60 km/h (37 mi/h)
Shift down points:
6th → 5th: 25 km/h (16 mi/h)
5th → 4th: 25 km/h (16 mi/h)
4th
→ 3rd: 25 km/h (16 mi/h)
3rd → 2nd: 25 km/h (16 mi/h)
2nd → 1st: 25 km/h (16 mi/h)
EAU16841
Engine break-in
There is never a more important period in the life of your engine than the period between 0 and 1600 km (1000 mi). For this reason, you should read the following material carefully.
Since the engine is brand new, do not put an excessive load on it for the first
1600 km (1000 mi). The various parts in the engine wear and polish themselves to the correct operating clearances.
During this period, prolonged full-throttle operation or any condition that might result in engine overheating must be avoided.
EAU17093
0–1000 km (0–600 mi)
Avoid prolonged operation above 6000 r/min. NOTICE: After 1000 km (600 mi) of operation, the engine oil must be changed and the oil filter cartridge or element replaced.
[ECA10302]
1000–1600 km (600–1000 mi)
Avoid prolonged operation above 7200 r/min.
6-3
U1CA11E0.book Page 4 Thursday, September 23, 2010 11:51 AM
OPERATION AND IMPORTANT RIDING POINTS
1600 km (1000 mi) and beyond
The vehicle can now be operated normally.
ECA10310
NOTICE
●
●
Keep the engine speed out of the tachometer red zone.
If any engine trouble should occur during the engine break-in period, immediately have a
Yamaha dealer check the vehicle.
EAU17213
Parking
When parking, stop the engine, and then remove the key from the main switch.
EWA10311
WARNING
●
●
●
Since the engine and exhaust system can become very hot, park in a place where pedestrians or children are not likely to touch them and be burned.
Do not park on a slope or on soft ground, otherwise the vehicle may overturn, increasing the risk of a fuel leak and fire.
Do not park near grass or other flammable materials which might catch fire.
6
6-4
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU17243
Periodic inspection, adjustment, and lubrication will keep your vehicle in the safest and most efficient condition possible. Safety is an obligation of the vehicle owner/operator. The most important points of vehicle inspection, adjustment, and lubrication are explained on the following pages.
The intervals given in the periodic maintenance charts should be simply considered as a general guide under normal riding conditions. However, depending on the weather, terrain, geographical location, and individual use, the maintenance intervals may need to be shortened.
EWA10321
WARNING
Failure to properly maintain the vehicle or performing maintenance activities incorrectly may increase your risk of injury or death during service or while using the vehicle. If you are not familiar with vehicle service, have a Yamaha dealer perform service.
EWA15121
WARNING
Turn off the engine when performing maintenance unless otherwise specified.
● A running engine has moving parts that can catch on body
● parts or clothing and electrical parts that can cause shocks or fires.
Running the engine while servicing can lead to eye injury, burns, fire, or carbon monoxide poisoning – possibly leading to
death. See page 2-1 for more in-
formation about carbon monoxide.
EWA15460
WARNING
Brake discs, calipers, drums, and linings can become very hot during use. To avoid possible burns, let brake components cool before touching them.
EAU17302
Emission controls not only function to ensure cleaner air, but are also vital to proper engine operation and maximum performance. In the following periodic maintenance charts, the services related to emissions control are grouped separately. These services require specialized data, knowledge, and equipment. Maintenance, replacement, or repair of the emission control devices and systems may be performed by any repair establishment or individual that is certified (if applicable). Yamaha dealers are trained and equipped to perform these particular services.
7-1
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
EAU17491
PERIODIC MAINTENANCE AND ADJUSTMENT
Owner’s tool kit
1. Owner’s tool kit
The owner’s tool kit is located inside the storage compartment under the pas-
The service information included in this manual and the tools provided in the owner’s tool kit are intended to assist you in the performance of preventive maintenance and minor repairs. However, additional tools such as a torque wrench may be necessary to perform certain maintenance work correctly.
TIP
If you do not have the tools or experience required for a particular job, have a Yamaha dealer perform it for you.
7-2
7
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU48490
7
TIP
●
●
From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months.
Items marked with an asterisk require special tools, data and technical skills, have a Yamaha dealer perform the service.
EAU17601
Periodic maintenance chart for the emission control system
No.
ITEM ROUTINE
INITIAL
600 mi
(1000 km) or
1 month
ODOMETER READINGS
4000 mi
(7000 km) or
6 months
8000 mi
(13000 km) or
12 months
12000 mi
(19000 km) or
18 months
16000 mi
(25000 km) or
24 months
20000 mi
(31000 km) or
30 months
1
2
3
*
*
*
Fuel line
Spark plugs
Valve clearance
4 *
Crankcase breather system
5
6
*
*
Fuel injection
Exhaust system
• Check fuel hoses for cracks or damage.
• Replace if necessary.
• Check condition.
• Adjust gap and clean.
• Replace every 8000 mi (13000 km) or 12 months.
• Check and adjust valve clearance when engine is cold.
• Check breather hose for cracks or damage.
• Replace if necessary.
• Check and adjust engine idle speed and synchronization.
• Check for leakage.
• Tighten if necessary.
• Replace gasket(s) if necessary.
√
√
√
√
√
√
√
Replace.
√
√
√
√
√
Every 26600 mi (42000 km)
√
√
√
√
Replace.
√
√
√
√
√
√
√
√
7-3
U1CA11E0.book Page 4 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
No.
ITEM ROUTINE
7 *
Evaporative emission control system
(for California only)
8 *
Air induction system
• Check control system for damage.
• Replace if necessary.
• Check the air cut-off valve, reed valve, and hose for damage.
• Replace any damaged parts.
INITIAL
600 mi
(1000 km) or
1 month
ODOMETER READINGS
4000 mi
(7000 km) or
6 months
8000 mi
(13000 km) or
12 months
12000 mi
(19000 km) or
18 months
16000 mi
(25000 km) or
24 months
20000 mi
(31000 km) or
30 months
√ √
√ √
7
7-4
U1CA11E0.book Page 5 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU32186
General maintenance and lubrication chart
No.
1 Air filter element
2 * Clutch
3 * Front brake
4 * Rear brake
5 * Brake hoses
6 * Wheels
7 * Tires
ITEM
8 * Wheel bearings
ROUTINE
• Replace.
• Check operation.
• Adjust or replace cable.
• Check operation, fluid level, and for fluid leakage.
• Replace brake pads if necessary.
• Check operation, fluid level, and for fluid leakage.
• Replace brake pads if necessary.
• Check for cracks or damage.
• Check for correct routing and clamping.
• Replace.
• Check runout and for damage.
• Replace if necessary.
• Check tread depth and for damage.
• Replace if necessary.
• Check air pressure.
• Correct if necessary.
• Check bearings for smooth operation.
• Replace if necessary.
INITIAL
600 mi
(1000 km) or
1 month
ODOMETER READINGS
4000 mi
(7000 km) or
6 months
8000 mi
(13000 km) or
12 months
12000 mi
(19000 km) or
18 months
16000 mi
(25000 km) or
24 months
20000 mi
(31000 km) or
30 months
Every 24000 mi (37000 km)
√ √ √ √ √ √
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Every 4 years
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
7-5
U1CA11E0.book Page 6 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
No.
9
10
*
11 *
ITEM
Swingarm pivot bearings
Drive chain
Steering bearings
12 * Chassis fasteners
13
14
15
16
Brake lever pivot shaft
Brake pedal pivot shaft
Clutch lever pivot shaft
Shift pedal pivot shaft
17 *
Centerstand and sidestand pivots
ROUTINE
INITIAL
600 mi
(1000 km) or
1 month
ODOMETER READINGS
4000 mi
(7000 km) or
6 months
8000 mi
(13000 km) or
12 months
12000 mi
(19000 km) or
18 months
16000 mi
(25000 km) or
24 months
20000 mi
(31000 km) or
30 months
• Check bearing assemblies for looseness.
• Check chain slack, alignment and condition.
• Adjust and lubricate chain with a special O-ring chain lubricant thoroughly.
• Check bearing assemblies for looseness.
• Moderately repack with lithiumsoap-based grease.
• Check all chassis fitting and fasteners.
• Correct if necessary.
√
√
√
√
√
√
√
√
√
Every 12000 mi (19000 km)
√
√ √
Every 600 mi (1000 km) and after washing the motorcycle, riding in the rain or riding in wet areas
√
√
√
√
√ √ √ √ √
• Apply silicone grease lightly.
• Apply lithium-soap-based grease lightly.
• Apply lithium-soap-based grease lightly.
• Apply lithium-soap-based grease lightly.
• Check operation.
• Apply lithium-soap-based grease lightly.
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
7
7-6
U1CA11E0.book Page 7 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
No.
ITEM ROUTINE
18 *
19 *
20 *
21 *
22
Sidestand switch
Front fork
Shock absorber assembly
Rear suspension link pivots
Engine oil
• Check operation and replace if necessary.
• Check operation and for oil leakage.
• Replace if necessary.
• Check operation and for oil leakage.
• Replace if necessary.
• Check operation.
• Correct if necessary.
• Change (warm engine before draining).
23 *
Engine oil filter cartridge
• Replace.
24 *
26 *
Cooling system
Control cables
• Check hoses for cracks or damage.
• Replace if necessary.
• Change with ethylene glycol antifreeze coolant every 24 months.
25 *
Front and rear brake switches
• Check operation.
• Apply Yamaha chain and cable lube or engine oil thoroughly.
INITIAL
600 mi
(1000 km) or
1 month
ODOMETER READINGS
4000 mi
(7000 km) or
6 months
8000 mi
(13000 km) or
12 months
12000 mi
(19000 km) or
18 months
16000 mi
(25000 km) or
24 months
20000 mi
(31000 km) or
30 months
√ √ √ √ √ √
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Change.
√
√
√
√
√
√
√
√
7-7
U1CA11E0.book Page 8 Thursday, September 23, 2010 11:51 AM
No.
ITEM
PERIODIC MAINTENANCE AND ADJUSTMENT
ROUTINE
INITIAL
600 mi
(1000 km) or
1 month
ODOMETER READINGS
4000 mi
(7000 km) or
6 months
8000 mi
(13000 km) or
12 months
12000 mi
(19000 km) or
18 months
16000 mi
(25000 km) or
24 months
20000 mi
(31000 km) or
30 months
27 * Throttle grip
28 *
Lights, signals and switches
• Check operation.
• Check throttle grip free play, and adjust if necessary.
• Lubricate cable and grip housing.
• Check operation.
• Adjust headlight beam.
√
√
√
√
√
√
√
√
√
√
√
EAU17650
TIP
●
●
Air filter
• This model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with compressed air to avoid damaging it.
• The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas.
Hydraulic brake service
• After disassembling the brake master cylinders and calipers, always change the fluid. Regularly check the brake fluid levels and fill the reservoirs as required.
• Every two years replace the internal components of the brake master cylinders and calipers, and change the brake fluid.
• Replace the brake hoses every four years and if cracked or damaged.
7
7-8
U1CA11E0.book Page 9 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU18771
Removing and installing panels
The panels shown need to be removed to perform some of the maintenance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed.
7
1. Panel A
2. Panel B
1. Panel C
Panels A and B
EAU40031
To install a panel
Place the panel in the original position, and then install the screws and the bolts.
To remove a panel
Remove the bolts and the screws, and then pull the panel off as shown.
Panel C
EAU19281
To remove the panel
Remove the screw, and then pull the panel off as shown.
1. Panel A
2. Screw
3. Bolt
7-9
U1CA11E0.book Page 10 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
1. Panel C
2. Screw
To install the panel
Place the panel in the original position, and then install the screw.
Checking the spark plugs
EAU19652
The spark plugs are important engine components, which should be checked periodically, preferably by a Yamaha dealer. Since heat and deposits will cause any spark plug to slowly erode, they should be removed and checked in accordance with the periodic maintenance and lubrication chart. In addition, the condition of the spark plugs can reveal the condition of the engine.
The porcelain insulator around the center electrode of each spark plug should be a medium-to-light tan (the ideal color when the vehicle is ridden normally), and all spark plugs installed in the engine should have the same color. If any spark plug shows a distinctly different color, the engine could be operating improperly. Do not attempt to diagnose such problems yourself. Instead, have a Yamaha dealer check the vehicle.
If a spark plug shows signs of electrode erosion and excessive carbon or other deposits, it should be replaced.
Before installing a spark plug, the spark plug gap should be measured with a wire thickness gauge and, if necessary, adjusted to specification.
1. Spark plug gap
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
Clean the surface of the spark plug gasket and its mating surface, and then wipe off any grime from the spark plug threads.
Tightening torque:
Spark plug:
13 Nm (1.3 m·kgf, 9.4 ft·lbf)
Specified spark plug:
NGK/CR9E
7-10
7
U1CA11E0.book Page 11 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
TIP
If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/4–1/2 turn past finger tight. However, the spark plug should be tightened to the specified torque as soon as possible.
ECA10840
NOTICE
Do not use any tools to remove or install the spark plug cap, otherwise the ignition coil coupler may get damaged. The spark plug cap may be difficult to remove because the rubber seal on the end of the cap fits tightly. To remove the spark plug cap, simply twist it back and forth while pulling it out; to install it, twist it back and forth while pushing it in.
EAU19681
Canister (for California only)
This model is equipped with a canister to prevent the discharging of fuel vapor into the atmosphere. Before operating this vehicle, make sure to check the following:
●
●
Check each hose connection.
Check each hose and canister for
● cracks or damage. Replace if damaged.
Make sure that the canister breather is not blocked, and if necessary, clean it.
EAU19879
Engine oil and oil filter cartridge
The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter cartridge replaced at the intervals specified in the periodic maintenance and lubrication chart.
To check the engine oil level
1. Place the vehicle on the centerstand. A slight tilt to the side can result in a false reading.
2. Start the engine, warm it up for several minutes, and then turn it off.
3. Wait a few minutes until the oil settles, and then check the oil level through the engine oil level check window located at the bottom-right side of the crankcase.
TIP
The engine oil should be between the minimum and maximum level marks.
7-11
U1CA11E0.book Page 12 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
4. Remove the engine oil filler cap, the engine oil drain bolt and its gasket to drain the oil from the crankcase.
2
1
1. Engine oil filler cap
2. Engine oil level check window
3. Maximum level mark
4. Minimum level mark
4. If the engine oil is below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level.
1. Engine oil drain bolt
2. Gasket
1
To change the engine oil (with or without oil filter cartridge replacement)
1. Place the vehicle on a level surface.
2. Start the engine, warm it up for several minutes, and then turn it off.
3. Place an oil pan under the engine to collect the used oil.
TIP
Skip steps 5–7 if the oil filter cartridge is not being replaced.
5. Remove the oil filter cartridge with an oil filter wrench.
7-12
1. Oil filter wrench
2. Oil filter cartridge
TIP
An oil filter wrench is available at a
Yamaha dealer.
6. Apply a thin coat of clean engine oil to the O-ring of the new oil filter cartridge.
7
U1CA11E0.book Page 13 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
Recommended engine oil:
Oil quantity:
Without oil filter cartridge replacement:
2.90 L (3.07 US qt, 2.55 Imp.qt)
With oil filter cartridge replacement:
3.10 L (3.28 US qt, 2.73 Imp.qt)
7
1. O-ring
TIP
Make sure that the O-ring is properly seated.
7. Install the new oil filter cartridge with an oil filter wrench, and then tighten it to the specified torque with a torque wrench.
1. Torque wrench
Tightening torque:
Oil filter cartridge:
17 Nm (1.7 m·kgf, 12 ft·lbf)
8. Install the engine oil drain bolt and its new gasket, and then tighten the bolt to the specified torque.
Tightening torque:
Engine oil drain bolt:
43 Nm (4.3 m·kgf, 31 ft·lbf)
9. Refill with the specified amount of the recommended engine oil, and then install and tighten the oil filler cap.
TIP
Be sure to wipe off spilled oil on any parts after the engine and exhaust system have cooled down.
ECA11620
NOTICE
●
●
In order to prevent clutch slippage (since the engine oil also lubricates the clutch), do not mix any chemical additives. Do not use oils with a diesel specification of “CD” or oils of a higher quality than specified. In addition, do not use oils labeled
“ENERGY CONSERVING II” or higher.
Make sure that no foreign material enters the crankcase.
7-13
U1CA11E0.book Page 14 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
10. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, immediately turn the engine off and check for the cause.
TIP
After the engine is started, the engine oil level warning light should go off if the oil level is sufficient.
ECA10401
NOTICE
If the oil level warning light flickers or remains on even if the oil level is correct, immediately turn the engine off and have a Yamaha dealer check the vehicle.
11. Turn the engine off, wait a few minutes until the oil settles, and then check the oil level and correct it if necessary.
EAU20070
Coolant
The coolant level should be checked before each ride. In addition, the coolant must be changed at the intervals specified in the periodic maintenance and lubrication chart.
EAU40044
To check the coolant level
1. Place the vehicle on the centerstand.
TIP
●
●
The coolant level must be checked on a cold engine since the level varies with engine temperature.
Make sure that the vehicle is positioned straight up when checking the coolant level. A slight tilt to the side can result in an incorrect reading.
2. Check the coolant level in the coolant reservoir.
TIP
The coolant should be between the minimum and maximum level marks.
1. Coolant reservoir
2. Maximum level mark
3. Minimum level mark
3. If the coolant is at or below the minimum level mark, remove panel C to access the coolant reser-
4. Remove the coolant reservoir cap, add coolant to the maximum level mark, and then install the reservoir cap. WARNING! Remove only the coolant reservoir cap. Never attempt to remove the radiator cap when the engine is hot.
[EWA15161]
NOTICE: If coolant is not available, use distilled water or soft tap water instead. Do not use hard water or salt water since it is harmful to the engine.
7-14
7
7
U1CA11E0.book Page 15 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
If water has been used instead of coolant, replace it with coolant as soon as possible, otherwise the cooling system will not be protected against frost and corrosion. If water has been added to the coolant, have a
Yamaha dealer check the antifreeze content of the coolant as soon as possible, otherwise the effectiveness of the coolant will be reduced.
[ECA10472]
EAU33031
Changing the coolant
The coolant must be changed at the intervals specified in the periodic maintenance and lubrication chart. Have a
Yamaha dealer change the coolant.
WARNING! Never attempt to remove the radiator cap when the engine is hot.
[EWA10381]
EAU40054
Replacing the air filter element
The air filter element should be replaced at the intervals specified in the periodic maintenance and lubrication chart. Replace the air filter element more frequently if you are riding in unusually wet or dusty areas.
1. Remove the rider seat. (See page
2. Remove panels A and B. (See page 7-9.)
3. Remove the fuel tank cowling bolts, and then pull the fuel tank cowling off.
1. Coolant reservoir cap
Coolant reservoir capacity (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
5. Install the panel.
1. Fuel tank cowling
2. Fuel tank cowling bolt
4. Remove the fuel tank bolts.
7-15
U1CA11E0.book Page 16 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
1. Fuel tank bolt
5. Lift the front of the fuel tank, and carefully tilt it back and away from the air filter case, but do not disconnect the fuel hoses.
WARNING! Make sure that the fuel tank is well supported. Do not tilt or pull the fuel tank too much, otherwise the fuel hoses may come loose, which could cause fuel leakage and a fire hazard.
[EWA10411]
6. Remove the air filter case cover by removing the screws. NOTICE:
When removing the air filter case cover, be careful not to allow foreign objects to drop into the air intake manifold.
[ECA12881]
1. Screw
2. Air filter case cover
7. Pull the air filter element out.
7-16
1. Air filter element
2. Air intake manifold
8. Insert a new air filter element into the air filter case. NOTICE: Make sure that the air filter element is properly seated in the air filter case. The engine should never be operated without the air filter element installed, otherwise the piston(s) and/or cylinder(s) may become excessively worn.
[ECA10481]
9. Install the air filter case cover by installing the screws.
10. Place the fuel tank in the original position. Make sure that the fuel hoses are properly connected and routed, and not pinched. Be sure to place the fuel tank breather
7
U1CA11E0.book Page 17 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT hose and the fuel tank overflow hose in the original position.
WARNING! Before placing the fuel tank in the original position, make sure that the fuel hoses are not damaged. If any fuel hose is damaged, do not start the engine but have a Yamaha dealer replace the hose, otherwise fuel may leak, creating a fire hazard.
[EWA11361]
13. Install the panels.
14. Install the rider seat.
EAU44734
Checking the engine idling speed
Check the engine idling speed and, if necessary, have it corrected by a
Yamaha dealer.
Engine idling speed:
1100–1300 r/min
7
2
1
3
1. Fuel tank breather hose (except for California)
2. Original position (paint mark)
3. Fuel tank overflow hose
11. Install the fuel tank bolts.
12. Place the fuel tank cowling in the original position, and then install the fuel tank cowling bolts.
7-17
U1CA11E0.book Page 18 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU21384
Checking the throttle grip free play
EAU21401
Valve clearance
The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise. To prevent this from occurring, the valve clearance must be adjusted by a Yamaha dealer at the intervals specified in the periodic maintenance and lubrication chart.
1. Throttle grip free play
The throttle grip free play should measure 3.0–5.0 mm (0.12–0.20 in) at the inner edge of the throttle grip. Periodically check the throttle grip free play and, if necessary, have a Yamaha dealer adjust it.
EAU21755
Tires
To maximize the performance, durability, and safe operation of your motorcycle, note the following points regarding the specified tires.
Tire air pressure
The tire air pressure should be checked and, if necessary, adjusted before each ride.
EWA10503
WARNING
Operation of this vehicle with improper tire pressure may cause severe injury or death from loss of control.
● The tire air pressure must be
● checked and adjusted on cold tires (i.e., when the temperature of the tires equals the ambient temperature).
The tire air pressure must be adjusted in accordance with the riding speed and with the total weight of rider, passenger, cargo, and accessories approved for this model.
7
7-18
U1CA11E0.book Page 19 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
Tire inspection
Tire air pressure (measured on cold tires):
0–90 kg (0–198 lb):
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
FZS10A 90–190 kg (198–419 lb)
FZS10AC 90–189 kg (198–417 lb):
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
High-speed riding:
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
Maximum load*:
FZS10A 190 kg (419 lb)
FZS10AC 189 kg (417 lb)
* Total weight of rider, passenger, cargo and accessories
1. Tire sidewall
2. Tire wear indicator
3. Tire tread depth
Always check the tires before operating the motorcycle. If a tire tread shows crosswise lines (minimum tread depth), if the tire has a nail or glass fragments in it, or if the sidewall is cracked, contact a Yamaha dealer immediately and have the tire replaced.
EWA10511
WARNING
Never overload your vehicle. Operation of an overloaded vehicle could cause an accident.
Minimum tire tread depth (front and rear):
1.0 mm (0.04 in)
●
●
●
EWA10581
WARNING
It is dangerous to ride with a worn-out tire. When a tire tread begins to show crosswise lines, have a Yamaha dealer replace the tire immediately.
The replacement of all wheeland brake-related parts, including the tires, should be left to a
Yamaha dealer, who has the necessary professional knowledge and experience to do so.
Ride at moderate speeds after changing a tire since the tire surface must first be “broken in” for it to develop its optimal characteristics.
7-19
U1CA11E0.book Page 20 Thursday, September 23, 2010 11:51 AM
Tire information
PERIODIC MAINTENANCE AND ADJUSTMENT
● Use only the tire valves and valve cores listed below to avoid tire deflation during a high-speed ride.
After extensive tests, only the tires listed below have been approved for this model by Yamaha Motor Co., Ltd.
1. Tire air valve
2. Tire air valve core
3. Tire air valve cap with seal
This motorcycle is equipped with tubeless tires, tire air valves and cast wheels.
EWA10481
WARNING
●
●
The front and rear tires should be of the same make and design, otherwise the handling characteristics of the motorcycle may be different, which could lead to an accident.
Always make sure that the valve caps are securely installed to prevent air pressure leakage.
Front tire:
Size:
120/70 ZR17M/C (58W)
Manufacturer/model:
DUNLOP/D221FA
Rear tire:
Size:
190/50 ZR17M/C (73W)
Manufacturer/model:
DUNLOP/D221G
FRONT and REAR:
Tire air valve:
TR412
Valve core:
#9100 (original)
EWA10600
WARNING
This motorcycle is fitted with superhigh-speed tires. Note the following points in order to make the most efficient use of these tires.
●
●
●
●
Use only the specified replacement tires. Other tires may run the danger of bursting at super high speeds.
Brand-new tires can have a relatively poor grip on certain road surfaces until they have been
“broken in”. Therefore, it is advisable before doing any highspeed riding to ride conservatively for approximately 100 km
(60 mi) after installing a new tire.
The tires must be warmed up before a high-speed run.
Always adjust the tire air pressure according to the operating conditions.
7
7-20
U1CA11E0.book Page 21 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU21962
Cast wheels
To maximize the performance, durability, and safe operation of your vehicle, note the following points regarding the specified wheels.
● The wheel rims should be checked for cracks, bends, warpage or other damage before each ride. If any damage is found, have a Yamaha dealer replace the wheel. Do not attempt even the smallest repair to
● the wheel. A deformed or cracked wheel must be replaced.
The wheel should be balanced whenever either the tire or wheel has been changed or replaced. An unbalanced wheel can result in poor performance, adverse handling characteristics, and a shortened tire life.
EAU22081
Adjusting the clutch lever free play
1. Clutch lever free play adjusting bolt
2. Clutch lever free play
The clutch lever free play should measure 10.0–15.0 mm (0.39–0.59 in) as shown. Periodically check the clutch lever free play and, if necessary, adjust it as follows.
To increase the clutch lever free play, turn the clutch lever free play adjusting bolt in direction (a). To decrease the clutch lever free play, turn the adjusting bolt in direction (b).
TIP
If the specified free play cannot be obtained as described above or if the clutch does not operate correctly, have a Yamaha dealer check the internal clutch mechanism.
7-21
U1CA11E0.book Page 22 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU37913
Checking the brake lever free play
1 braking performance, which may result in loss of control and an accident.
Brake light switches
EAU22273
1. No brake lever free play
There should be no free play at the brake lever end. If there is free play, have a Yamaha dealer inspect the brake system.
EWA14211
WARNING
A soft or spongy feeling in the brake lever can indicate the presence of air in the hydraulic system. If there is air in the hydraulic system, have a
Yamaha dealer bleed the system before operating the vehicle. Air in the hydraulic system will diminish the
1. Rear brake light switch
2. Rear brake light switch adjusting nut
The brake light, which is activated by the brake pedal and brake lever, should come on just before braking takes effect. If necessary, adjust the rear brake light switch as follows, but the front brake light switch should be adjusted by a Yamaha dealer.
Turn the rear brake light switch adjusting nut while holding the rear brake light switch in place. To make the brake light come on earlier, turn the adjusting nut in direction (a). To make the brake light come on later, turn the adjusting nut in direction (b).
7
7-22
U1CA11E0.book Page 23 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU22392
Checking the front and rear brake pads
The front and rear brake pads must be checked for wear at the intervals specified in the periodic maintenance and lubrication chart.
the point that a wear indicator almost touches the brake disc, have a Yamaha dealer replace the brake pads as a set.
Rear brake pads
EAU46291
EAU39371
Checking the brake fluid level
Front brake
EAU36890
Front brake pads
7
1
1
1. Minimum level mark
Rear brake
1
1. Brake pad wear indicator
Each front brake pad is provided with wear indicators, which allows you to check the brake pad wear without having to disassemble the brake. To check the brake pad wear, check the position of the wear indicators while applying the brake. If a brake pad has worn to
1. Brake pad wear indicator groove
Each rear brake pad is provided with wear indicator grooves, which allow you to check the brake pad wear without having to disassemble the brake.
To check the brake pad wear, check the wear indicator grooves. If a brake pad has worn to the point that a wear indicator groove almost appears, have a Yamaha dealer replace the brake pads as a set.
1. Minimum level mark
Insufficient brake fluid may allow air to enter the brake system, possibly causing it to become ineffective.
7-23
U1CA11E0.book Page 24 Thursday, September 23, 2010 11:51 AM
Before riding, check that the brake fluid is above the minimum level mark and replenish if necessary. A low brake fluid level may indicate worn brake pads and/or brake system leakage. If the brake fluid level is low, be sure to check the brake pads for wear and the brake system for leakage.
TIP
The rear brake fluid reservoir is located
behind panel C. (See page 7-9.)
Observe these precautions:
● When checking the fluid level, make sure that the top of the brake fluid reservoir is level.
● Use only the recommended quality brake fluid, otherwise the rubber seals may deteriorate, causing leakage and poor braking performance.
Recommended brake fluid:
DOT 4
● Refill with the same type of brake fluid. Mixing fluids may result in a harmful chemical reaction and lead to poor braking performance.
PERIODIC MAINTENANCE AND ADJUSTMENT
●
●
●
Be careful that water does not enter the brake fluid reservoir when refilling. Water will significantly lower the boiling point of the fluid and may result in vapor lock.
Brake fluid may deteriorate painted surfaces or plastic parts. Always clean up spilled fluid immediately.
As the brake pads wear, it is normal for the brake fluid level to gradually go down. However, if the brake fluid level goes down suddenly, have a Yamaha dealer check the cause.
EAU22731
Changing the brake fluid
Have a Yamaha dealer change the brake fluid at the intervals specified in the TIP after the periodic maintenance and lubrication chart. In addition, have the oil seals of the master cylinders and calipers as well as the brake hoses replaced at the intervals listed below or whenever they are damaged or leaking.
●
●
Oil seals: Replace every two years.
Brake hoses: Replace every four years.
7-24
7
U1CA11E0.book Page 25 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU22760
Drive chain slack
The drive chain slack should be checked before each ride and adjusted if necessary.
EAU22794
To check the drive chain slack
1. Place the motorcycle on the centerstand.
2. Shift the transmission into the neutral position.
3. Measure the drive chain slack as shown.
1. Drive chain slack
Drive chain slack:
20.0–30.0 mm (0.79–1.18 in)
To adjust the drive chain slack
EAU49312
Consult a Yamaha dealer before adjusting the drive chain slack.
1. Take the motorcycle off the centerstand, and then put the sidestand down.
2. Loosen the axle nut and the locknut on each side of the swingarm.
3. Place the motorcycle on the centerstand.
4. To tighten the drive chain, turn the drive chain slack adjusting bolt on each side of the swingarm in direction (a). To loosen the drive chain, turn the adjusting bolt on each side of the swingarm in direction (b), and then push the rear wheel forward. NOTICE: Improper drive chain slack will overload the engine as well as other vital parts of the motorcycle and can lead to chain slippage or breakage.
To prevent this from occurring, keep the drive chain slack within the specified limits.
[ECA10571]
4. If the drive chain slack is incorrect, adjust it as follows.
TIP
Using the alignment marks on each side of the swingarm, make sure that both drive chain pullers are in the same position for proper wheel alignment.
1. Axle nut
2. Drive chain slack adjusting bolt
3. Locknut
4. Drive chain puller
5. Alignment marks
5. Take the motorcycle off the centerstand, and then put the sidestand down.
6. Tighten the axle nut, then the locknuts to the specified torques.
7-25
U1CA11E0.book Page 26 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
Tightening torques:
Axle nut:
150 Nm (15 m·kgf, 108 ft·lbf)
Locknut:
16 Nm (1.6 m·kgf, 12 ft·lbf)
7. Make sure that the drive chain pullers are in the same position, the drive chain slack is correct, and the drive chain moves smoothly.
EAU23025
Cleaning and lubricating the drive chain
The drive chain must be cleaned and lubricated at the intervals specified in the periodic maintenance and lubrication chart, otherwise it will quickly wear out, especially when riding in dusty or wet areas. Service the drive chain as follows.
ECA10583
NOTICE
The drive chain must be lubricated after washing the motorcycle, riding in the rain or riding in wet areas.
1. Clean the drive chain with kerosene and a small soft brush.
NOTICE: To prevent damaging the O-rings, do not clean the drive chain with steam cleaners, high-pressure washers or inappropriate solvents.
[ECA11121]
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a special O-ring chain lubricant. NOTICE: Do not use engine oil or any other lubricants for the drive chain, as they may contain substances that could damage the O-rings.
[ECA11111]
7-26
7
U1CA11E0.book Page 27 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23095
Checking and lubricating the cables
The operation of all control cables and the condition of the cables should be checked before each ride, and the cables and cable ends should be lubricated if necessary. If a cable is damaged or does not move smoothly, have a
Yamaha dealer check or replace it.
WARNING! Damage to the outer housing of cables may result in internal rusting and cause interference with cable movement. Replace damaged cables as soon as possible to prevent unsafe conditions.
[EWA10711]
EAU23114
Checking and lubricating the throttle grip and cable
The operation of the throttle grip should be checked before each ride. In addition, the cable should be lubricated by a
Yamaha dealer at the intervals specified in the periodic maintenance chart.
The throttle cable is equipped with a rubber cover. Make sure that the cover is securely installed. Even though the cover is installed correctly, it does not completely protect the cable from water entry. Therefore, use care not to pour water directly onto the cover or cable when washing the vehicle. If the cable or cover becomes dirty, wipe clean with a moist cloth.
Recommended lubricant:
Yamaha Chain and Cable Lube or engine oil
EAU44272
Checking and lubricating the brake and shift pedals
Brake pedal
Shift pedal
The operation of the brake and shift pedals should be checked before each ride, and the pedal pivots should be lubricated if necessary.
7-27
U1CA11E0.book Page 28 Thursday, September 23, 2010 11:51 AM
Recommended lubricant:
Lithium-soap-based grease
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23142
Checking and lubricating the brake and clutch levers
Brake lever
Recommended lubricants:
Brake lever:
Silicone grease
Clutch lever:
Lithium-soap-based grease
Clutch lever
7
The operation of the brake and clutch levers should be checked before each ride, and the lever pivots should be lubricated if necessary.
7-28
U1CA11E0.book Page 29 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23213
Checking and lubricating the centerstand and sidestand
Recommended lubricant:
Lithium-soap-based grease
The operation of the centerstand and sidestand should be checked before each ride, and the pivots and metal-tometal contact surfaces should be lubricated if necessary.
EWA10741
WARNING
If the centerstand or sidestand does not move up and down smoothly, have a Yamaha dealer check or repair it. Otherwise, the centerstand or sidestand could contact the ground and distract the operator, resulting in a possible loss of control.
EAU23272
Checking the front fork
The condition and operation of the front fork must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart.
To check the condition
Check the inner tubes for scratches, damage and excessive oil leakage.
To check the operation
1. Place the vehicle on a level surface and hold it in an upright position. WARNING! To avoid injury, securely support the vehicle so there is no danger of it falling over.
[EWA10751]
2. While applying the front brake, push down hard on the handlebars several times to check if the front fork compresses and rebounds smoothly.
7-29
U1CA11E0.book Page 30 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
ECA10590
NOTICE
If any damage is found or the front fork does not operate smoothly, have a Yamaha dealer check or repair it.
EAU45511
Checking the steering
Worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as follows at the intervals specified in the periodic maintenance and lubrication chart.
1. Place the vehicle on the centerstand. WARNING! To avoid inju- ry, securely support the vehicle so there is no danger of it falling over.
[EWA10751]
2. Hold the lower ends of the front fork legs and try to move them forward and backward. If any free play can be felt, have a Yamaha dealer check or repair the steering.
EAU23291
Checking the wheel bearings
The front and rear wheel bearings must be checked at the intervals specified in the periodic maintenance and lubrication chart. If there is play in the wheel hub or if the wheel does not turn smoothly, have a Yamaha dealer check the wheel bearings.
7
7-30
U1CA11E0.book Page 31 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
Battery
EAU50210
1. Positive battery lead (red)
2. Negative battery lead (black)
3. Battery
The battery is located under the rider
This model is equipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electrolyte or to add distilled water. However, the battery lead connections need to be checked and, if necessary, tightened.
EWA10760
WARNING
● Electrolyte is poisonous and dangerous since it contains sulfuric acid, which causes severe burns. Avoid any contact with
●
● skin, eyes or clothing and always shield your eyes when working near batteries. In case of contact, administer the following FIRST AID.
• EXTERNAL: Flush with plenty of water.
• INTERNAL: Drink large quantities of water or milk and immediately call a physician.
• EYES: Flush with water for 15 minutes and seek prompt medical attention.
Batteries produce explosive hydrogen gas. Therefore, keep sparks, flames, cigarettes, etc., away from the battery and provide sufficient ventilation when charging it in an enclosed space.
KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.
To charge the battery
Have a Yamaha dealer charge the battery as soon as possible if it seems to have discharged. Keep in mind that the battery tends to discharge more quickly if the vehicle is equipped with optional electrical accessories.
ECA16521
NOTICE
To charge a VRLA (Valve Regulated
Lead Acid) battery, a special (constant-voltage) battery charger is required. Using a conventional battery charger will damage the battery.
To store the battery
1. If the vehicle will not be used for more than one month, remove the battery, fully charge it, and then place it in a cool, dry place.
NOTICE: When removing the battery, be sure the key is turned to “OFF”, then disconnect the negative lead before disconnecting the positive lead.
[ECA16302]
2. If the battery will be stored for more than two months, check it at least once a month and fully charge it if necessary.
3. Fully charge the battery before installation. NOTICE: When install- ing the battery, be sure the key
7-31
U1CA11E0.book Page 32 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT is turned to “OFF”, then connect the positive lead before connecting the negative lead.
[ECA16840]
4. After installation, make sure that the battery leads are properly connected to the battery terminals.
ECA16530
NOTICE
Always keep the battery charged.
Storing a discharged battery can cause permanent battery damage.
EAU43012
Replacing the fuses
The main fuse, the fuel injection system fuse, and the fuse box, which contains the fuses for the individual circuits, are
located under the rider seat. (See page
1. Main fuse
2. Fuse box
3. Fuel injection system fuse
4. Fuel injection system spare fuse
1. Fuse box
2. Headlight fuse
3. Ignition fuse
4. Signaling system fuse
5. Backup fuse (for clock)
6. Right radiator fan fuse
7. Left radiator fan fuse
8. Spare fuse
If a fuse is blown, replace it as follows.
TIP
Include steps 2, 3, 7 and 8 only for the fuel injection system fuse.
1. Turn the key to “OFF” and turn off the electrical circuit in question.
2. Unhook the battery band, and then remove the battery cover.
7
7-32
U1CA11E0.book Page 33 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
4. Remove the blown fuse, and then install a new fuse of the specified amperage. WARNING! Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire.
[EWA15131]
1. Battery band
2. Battery cover
3. Remove the starter relay cover by pulling it upward.
1
1. Starter relay cover
2. Fuel injection system fuse
3. Fuel injection system spare fuse
2
3
Specified fuses:
Main fuse:
50.0 A
Headlight fuse:
20.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
15.0 A
Fuel injection system fuse:
15.0 A
Radiator fan fuse:
10.0 A
× 2
Backup fuse:
10.0 A
5. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates.
6. If the fuse immediately blows again, have a Yamaha dealer check the electrical system.
7-33
7. Install the starter relay cover.
8. Install the battery cover, and then hook the battery band onto the holder.
U1CA11E0.book Page 34 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23933
Replacing a headlight bulb
This model is equipped with halogen bulb headlights. If a headlight bulb burns out, replace it as follows.
ECA10650
NOTICE
Take care not to damage the following parts:
● Headlight bulb
Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity
● of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner.
Headlight lens
Do not affix any type of tinted film or stickers to the headlight lens.
Do not use a headlight bulb of a wattage higher than specified.
1. Do not touch the glass part of the bulb.
1. Disconnect the headlight coupler, and then remove the bulb cover.
1. Headlight coupler
2. Headlight bulb cover
2. Unhook the headlight bulb holder, and then remove the burnt-out bulb.
1. Headlight bulb holder
3. Place a new headlight bulb into position, and then secure it with the bulb holder.
4. Install the headlight bulb cover, and then connect the coupler.
5. Have a Yamaha dealer adjust the headlight beam if necessary.
7
7-34
U1CA11E0.book Page 35 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU24115
Replacing the tail/brake light bulb
1. Remove the passenger seat. (See page 4-15.)
2. Remove the tail/brake light bulb socket (together with the bulb) by turning it counterclockwise.
EAU43003
Replacing a turn signal light bulb
1. Remove the turn signal light unit by removing the screw.
1. Turn signal light bulb socket
3. Remove the burnt-out bulb by pulling it out.
7
1. Tail/brake light bulb socket
3. Remove the burnt-out bulb by pushing it in and turning it counterclockwise.
4. Insert a new bulb into the socket, push it in, and then turn it clockwise until it stops.
5. Install the socket (together with the bulb) by turning it clockwise.
6. Install the passenger seat.
1. Turn signal light unit
2. Screw
2. Remove the socket (together with the bulb) by turning it counterclockwise.
1. Turn signal light bulb
4. Insert a new bulb into the socket.
5. Install the socket (together with the bulb) by turning it clockwise.
6. Install the turn signal light unit by installing the screw.
7-35
U1CA11E0.book Page 36 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU24313
Replacing the license plate light bulb
1. Remove the license plate light unit by removing the screws.
1
2
1. License plate light unit
2. Screw
2. Remove the license plate light bulb socket (together with the bulb) by pulling it out.
1. License plate light bulb
2. License plate light bulb socket
3. Remove the burnt-out bulb by pulling it out.
4. Insert a new bulb into the socket.
5. Install the socket (together with the bulb) by pushing it in.
6. Install the license plate light unit by installing the screws.
Front wheel
EAU24360
EAU40201
To remove the front wheel
EWA10821
WARNING
To avoid injury, securely support the vehicle so there is no danger of it falling over.
1. Place the vehicle on the centerstand.
2. Loosen the front wheel axle pinch bolt, then the wheel axle and the brake caliper bolts.
3
2
7
1
1. Front wheel axle pinch bolt
2. Wheel axle
3. Brake caliper bolt
7-36
U1CA11E0.book Page 37 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
3. Remove the brake hose holder on each side by removing the bolt and nut.
4. Remove the brake caliper (together with the reflector) on each side by removing the bolts. NOTICE:
Do not apply the brake after the brake calipers have been removed, otherwise the brake pads will be forced shut.
[ECA11051]
1. Brake hose holder
2. Bolt and nut
3. Brake caliper bolt
4. Brake caliper
5. Reflector
5. Pull the wheel axle out, and then remove the wheel.
EAU40211
To install the front wheel
1. Lift the wheel up between the fork legs.
2. Insert the wheel axle.
3. Install the brake caliper (together with the reflector) on each side by installing the bolts.
TIP
Make sure that there is enough space between the brake pads before installing the brake calipers onto the brake discs.
4. Install the brake hose holder on each side by installing the bolt and nut.
5. Take the vehicle off the centerstand so that the front wheel is on the ground, and then put the sidestand down.
6. Tighten the wheel axle, the front wheel axle pinch bolt, and the brake caliper bolts to the specified torques.
Tightening torques:
Wheel axle:
72 Nm (7.2 m·kgf, 52 ft·lbf)
Front wheel axle pinch bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
Brake caliper bolt:
40 Nm (4.0 m·kgf, 29 ft·lbf)
7. Push down hard on the handlebar several times to check for proper fork operation.
7-37
U1CA11E0.book Page 38 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
Rear wheel
EAU25080
EAU40022
To remove the rear wheel
EWA10821
WARNING
To avoid injury, securely support the vehicle so there is no danger of it falling over.
1. Loosen the axle nut.
2
3
1
1. Axle nut
2. Brake caliper bracket
3. Brake caliper
2. Place the vehicle on the centerstand.
3. Remove the axle nut.
4. Loosen the locknut on each side of the swingarm.
(a)
1 2
1. Drive chain slack adjusting bolt
2. Locknut
5. Turn the drive chain slack adjusting bolts fully in direction (a) and push the wheel forward.
6. Remove the drive chain from the rear sprocket.
TIP
●
●
If the drive chain is difficult to remove, remove the wheel axle first, and then lift the wheel upward enough to remove the drive chain from the rear sprocket.
The drive chain cannot be disassembled.
7. While supporting the brake caliper bracket, pull the wheel axle out, and then remove the wheel.
7-38
NOTICE: Do not apply the brake after the wheel has been removed together with the brake disc, otherwise the brake pads will be forced shut.
[ECA11071]
1. Wheel axle
EAU48402
To install the rear wheel
1. Install the wheel and the brake caliper bracket by inserting the wheel axle from the left-hand side.
TIP
●
●
Make sure that the slot in the brake caliper bracket is fit over the retainer on the swingarm.
Make sure that there is enough space between the brake pads before installing the wheel.
7
U1CA11E0.book Page 39 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
Tightening torques:
Axle nut:
150 Nm (15 m·kgf, 108 ft·lbf)
Locknut:
16 Nm (1.6 m·kgf, 12 ft·lbf)
7
1. Slot
2. Retainer
2. Install the drive chain onto the rear sprocket.
3. Install the axle nut.
4. Take the vehicle off the centerstand so that the rear wheel is on the ground, and then put the sidestand down.
5. Adjust the drive chain slack. (See page 7-25.)
6. Tighten the axle nut, and then tighten the locknuts to the specified torques.
EAU25871
Troubleshooting
Although Yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur during operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and loss of power.
The following troubleshooting charts represent quick and easy procedures for checking these vital systems yourself. However, should your motorcycle require any repair, take it to a Yamaha dealer, whose skilled technicians have the necessary tools, experience, and know-how to service the motorcycle properly.
Use only genuine Yamaha replacement parts. Imitation parts may look like
Yamaha parts, but they are often inferior, have a shorter service life and can lead to expensive repair bills.
EWA15141
WARNING
When checking the fuel system, do not smoke, and make sure there are no open flames or sparks in the area, including pilot lights from water
7-39
U1CA11E0.book Page 40 Thursday, September 23, 2010 11:51 AM heaters or furnaces. Gasoline or gasoline vapors can ignite or explode, causing severe injury or property damage.
PERIODIC MAINTENANCE AND ADJUSTMENT
7
7-40
U1CA11E0.book Page 41 Thursday, September 23, 2010 11:51 AM
7
PERIODIC MAINTENANCE AND ADJUSTMENT
Troubleshooting charts
Starting problems or poor engine performance
1. Fuel
Check the fuel level in the fuel tank.
There is enough fuel.
There is no fuel.
Check the compression.
Supply fuel.
The engine does not start.
Check the compression.
2. Compression
Operate the electric starter.
There is compression.
There is no compression.
Check the ignition.
Have a Yamaha dealer check the vehicle.
3. Ignition
Remove the spark plugs and check the electrodes.
Wet
Wipe off with a dry cloth and correct the spark plug gaps, or replace the spark plugs.
Operate the electric starter.
Dry Have a Yamaha dealer check the vehicle.
The engine does not start.
Check the battery.
4. Battery
Operate the electric starter.
The engine turns over quickly.
The engine turns over slowly.
The battery is good.
Check the battery lead connections, and have a Yamaha dealer charge the battery if necessary.
The engine does not start.
Have a Yamaha dealer check the vehicle.
EAU42502
7-41
U1CA11E0.book Page 42 Thursday, September 23, 2010 11:51 AM
PERIODIC MAINTENANCE AND ADJUSTMENT
Engine overheating
●
●
EWAT1040
WARNING
Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
Wait until the engine has cooled.
Check the coolant level in the reservoir and radiator.
The coolant level is low.
Check the cooling system for leakage.
The coolant level is OK.
There is leakage.
Have a Yamaha dealer check and repair the cooling system.
There is no leakage.
Add coolant. (See TIP.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
7
TIP
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant as soon as possible.
7-42
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
8
MOTORCYCLE CARE AND STORAGE
EAU37833
Matte color caution
ECA15192
NOTICE
Some models are equipped with matte colored finished parts. Be sure to consult a Yamaha dealer for advice on what products to use before cleaning the vehicle. Using a brush, harsh chemical products or cleaning compounds when cleaning these parts will scratch or damage their surface. Wax also should not be applied to any matte colored finished parts.
Care
EAU26014
While the open design of a motorcycle reveals the attractiveness of the technology, it also makes it more vulnerable. Rust and corrosion can develop even if high-quality components are used. A rusty exhaust pipe may go unnoticed on a car, however, it detracts from the overall appearance of a motorcycle. Frequent and proper care does not only comply with the terms of the warranty, but it will also keep your motorcycle looking good, extend its life and optimize its performance.
ucts onto seals, gaskets, sprockets, the drive chain and wheel axles. Always rinse the dirt and degreaser off with water.
Before cleaning
1. Cover the muffler outlet with a plastic bag after the engine has cooled down.
2. Make sure that all caps and covers as well as all electrical couplers and connectors, including the spark plug caps, are tightly installed.
3. Remove extremely stubborn dirt, like oil burnt onto the crankcase, with a degreasing agent and a brush, but never apply such prod-
8-1
Cleaning
ECA10772
NOTICE
●
●
Avoid using strong acidic wheel cleaners, especially on spoked wheels. If such products are used on hard-to-remove dirt, do not leave the cleaner on the affected area any longer than instructed. Also, thoroughly rinse the area off with water, immediately dry it, and then apply a corrosion protection spray.
Improper cleaning can damage plastic parts (such as cowlings, panels, windshields, headlight lenses, meter lenses, etc.) and the mufflers. Use only a soft, clean cloth or sponge with water to clean plastic. However, if the plastic parts cannot be thoroughly cleaned with water, diluted mild detergent with water may be used. Be sure to rinse
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
MOTORCYCLE CARE AND STORAGE
●
●
● off any detergent residue using plenty of water, as it is harmful to plastic parts.
Do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or thinner, fuel (gasoline), rust removers or inhibitors, brake fluid, antifreeze or electrolyte.
Do not use high-pressure washers or steam-jet cleaners since they cause water seepage and deterioration in the following areas: seals (of wheel and swingarm bearings, fork and brakes), electric components (couplers, connectors, instruments, switches and lights), breather hoses and vents.
For motorcycles equipped with a windshield: Do not use strong cleaners or hard sponges as they will cause dulling or scratching. Some cleaning compounds for plastic may leave scratches on the windshield.
Test the product on a small hidden part of the windshield to make sure that it does not leave any marks. If the windshield is scratched, use a quality plastic polishing compound after washing.
After normal use
Remove dirt with warm water, a mild detergent, and a soft, clean sponge, and then rinse thoroughly with clean water. Use a toothbrush or bottlebrush for hard-to-reach areas. Stubborn dirt and insects will come off more easily if the area is covered with a wet cloth for a few minutes before cleaning.
After riding in the rain, near the sea or on salt-sprayed roads
Since sea salt or salt sprayed on roads during winter are extremely corrosive in combination with water, carry out the following steps after each ride in the rain, near the sea or on salt-sprayed roads.
8-2
TIP
Salt sprayed on roads in the winter may remain well into spring.
1. Clean the motorcycle with cold water and a mild detergent, after the engine has cooled down.
NOTICE: Do not use warm water since it increases the corrosive action of the salt.
[ECA10791]
2. Apply a corrosion protection spray on all metal, including chrome- and nickel-plated, surfaces to prevent corrosion.
After cleaning
1. Dry the motorcycle with a chamois or an absorbing cloth.
2. Immediately dry the drive chain and lubricate it to prevent it from rusting.
3. Use a chrome polish to shine chrome, aluminum and stainlesssteel parts, including the exhaust system. (Even the thermally induced discoloring of stainlesssteel exhaust systems can be removed through polishing.)
8
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
8
MOTORCYCLE CARE AND STORAGE
4. To prevent corrosion, it is recommended to apply a corrosion protection spray on all metal, including chrome- and nickel-plated, surfaces.
5. Use spray oil as a universal cleaner to remove any remaining dirt.
6. Touch up minor paint damage caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely before storing or covering it.
EWA11131
WARNING
Contaminants on the brakes or tires can cause loss of control.
● Make sure that there is no oil or wax on the brakes or tires.
● If necessary, clean the brake discs and brake linings with a regular brake disc cleaner or acetone, and wash the tires with warm water and a mild detergent. Before riding at higher speeds, test the motorcycle’s braking performance and cornering behavior.
ECA10800
NOTICE
●
●
●
Apply spray oil and wax sparingly and make sure to wipe off any excess.
Never apply oil or wax to any rubber and plastic parts, but treat them with a suitable care product.
Avoid using abrasive polishing compounds as they will wear away the paint.
TIP
●
●
Consult a Yamaha dealer for advice on what products to use.
Washing, rainy weather or humid climates can cause the headlight lens to fog. Turning the headlight on for a short period of time will help remove the moisture from the lens.
Storage
EAU26182
Short-term
Always store your motorcycle in a cool, dry place and, if necessary, protect it against dust with a porous cover. Be sure the engine and the exhaust system are cool before covering the motorcycle.
ECA10810
NOTICE
●
●
Storing the motorcycle in a poorly ventilated room or covering it with a tarp, while it is still wet, will allow water and humidity to seep in and cause rust.
To prevent corrosion, avoid damp cellars, stables (because of the presence of ammonia) and areas where strong chemicals are stored.
Long-term
Before storing your motorcycle for several months:
1. Follow all the instructions in the
“Care” section of this chapter.
8-3
U1CA11E0.book Page 4 Thursday, September 23, 2010 11:51 AM
2. Fill up the fuel tank and add fuel stabilizer (if available) to prevent the fuel tank from rusting and the fuel from deteriorating.
3. Perform the following steps to protect the cylinders, piston rings, etc.
from corrosion.
a. Remove the spark plug caps and spark plugs.
b. Pour a teaspoonful of engine oil into each spark plug bore.
c. Install the spark plug caps onto the spark plugs, and then place the spark plugs on the cylinder head so that the electrodes are grounded. (This will limit sparking during the next step.) d. Turn the engine over several times with the starter. (This will coat the cylinder walls with oil.)
WARNING! To prevent damage or injury from sparking, make sure to ground the spark plug electrodes while turning the engine over.
[EWA10951]
MOTORCYCLE CARE AND STORAGE e. Remove the spark plug caps from the spark plugs, and then install the spark plugs and the spark plug caps.
4. Lubricate all control cables and the pivoting points of all levers and pedals as well as of the sidestand/centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift the motorcycle so that both of its wheels are off the ground. Alternatively, turn the wheels a little every month in order to prevent the tires from becoming degraded in one spot.
6. Cover the muffler outlet with a plastic bag to prevent moisture from entering it.
7. Remove the battery and fully charge it. Store it in a cool, dry place and charge it once a month.
Do not store the battery in an excessively cold or warm place [less than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information on storing the battery, see page
TIP
Make any necessary repairs before storing the motorcycle.
8
8-4
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
9
SPECIFICATIONS
Dimensions:
Overall length:
2140 mm (84.3 in)
Overall width:
770 mm (30.3 in)
Overall height:
1205 mm (47.4 in)
Seat height:
815 mm (32.1 in)
Wheelbase:
1460 mm (57.5 in)
Ground clearance:
135 mm (5.31 in)
Minimum turning radius:
3000 mm (118.1 in)
Weight:
Curb weight:
FZS10A 220 kg (485 lb)
FZS10AC 221 kg (487 lb)
Engine:
Engine type:
Liquid cooled 4-stroke, DOHC
Cylinder arrangement:
Inline 4-cylinder
Displacement:
998 cm³
Bore
× stroke:
77.0
× 53.6 mm (3.03 × 2.11 in)
Compression ratio:
11.50 :1
Starting system:
Electric starter
Lubrication system:
Wet sump
Engine oil:
Recommended brand:
YAMALUBE
Type:
SAE 10W-30, 10W-40, 10W-50, 15W-40,
20W-40 or 20W-50
0 10 30 50 70 90 110 130 ˚F
SAE 10W-30
SAE 10W-40
SAE 10W-50
SAE 15W-40
SAE 20W-40
SAE 20W-50
–20 –10 0 10 20 30 40 50 ˚C
Recommended engine oil grade:
API service SG type or higher, JASO standard MA
Engine oil quantity:
Without oil filter cartridge replacement:
2.90 L (3.07 US qt, 2.55 Imp.qt)
With oil filter cartridge replacement:
3.10 L (3.28 US qt, 2.73 Imp.qt)
Cooling system:
Coolant reservoir capacity (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator capacity (including all routes):
2.25 L (2.38 US qt, 1.98 Imp.qt)
Air filter:
Air filter element:
Oil-coated paper element
9-1
Fuel:
Recommended fuel:
Unleaded gasoline only
Fuel tank capacity:
18.0 L (4.76 US gal, 3.96 Imp.gal)
Fuel reserve amount:
3.4 L (0.90 US gal, 0.75 Imp.gal)
Fuel injection:
Throttle body:
ID mark:
FZS10A 2D11 20
FZS10AC 3C35 10
Spark plug(s):
Manufacturer/model:
NGK/CR9E
Spark plug gap:
0.7–0.8 mm (0.028–0.031 in)
Clutch:
Clutch type:
Wet, multiple-disc
Transmission:
Primary reduction ratio:
1.512 (65/43)
Final drive:
Chain
Secondary reduction ratio:
2.647 (45/17)
Transmission type:
Constant mesh 6-speed
Operation:
Left foot operation
Gear ratio:
1st:
2.533 (38/15)
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
2nd:
2.063 (33/16)
3rd:
1.762 (37/21)
4th:
1.522 (35/23)
5th:
1.350 (27/20)
6th:
1.208 (29/24)
Chassis:
Frame type:
Diamond
Caster angle:
25.00 °
Trail:
109 mm (4.3 in)
Front tire:
Type:
Tubeless
Size:
120/70 ZR17M/C (58W)
Manufacturer/model:
DUNLOP/D221FA
Rear tire:
Type:
Tubeless
Size:
190/50 ZR17M/C (73W)
Manufacturer/model:
DUNLOP/D221G
Loading:
Maximum load:
FZS10A 190 kg (419 lb)
FZS10AC 189 kg (417 lb)
(Total weight of rider, passenger, cargo and accessories)
Tire air pressure (measured on cold tires):
Loading condition:
0–90 kg (0–198 lb)
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
Loading condition:
FZS10A 90–190 kg (198–419 lb)
FZS10AC 90–189 kg (198–417 lb)
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
High-speed riding:
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
Front wheel:
Wheel type:
Cast wheel
Rim size:
17M/C x MT3.50
Rear wheel:
Wheel type:
Cast wheel
9-2
SPECIFICATIONS
Rim size:
17M/C x MT6.00
Front brake:
Type:
Dual disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4
Rear brake:
Type:
Single disc brake
Operation:
Right foot operation
Recommended fluid:
DOT 4
Front suspension:
Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
130.0 mm (5.12 in)
Rear suspension:
Type:
Swingarm (link suspension)
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
130.0 mm (5.12 in)
Electrical system:
Ignition system:
TCI
9
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
9
SPECIFICATIONS
Charging system:
AC magneto
Battery:
Model:
YTZ14S
Voltage, capacity:
12 V, 11.2 Ah
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage × quantity:
Headlight:
12 V, 60 W/55 W
× 2
Tail/brake light:
12 V, 5.0 W/21.0 W
× 1
Front turn signal/position light:
12 V, 21 W/5.0 W
× 2
Rear turn signal light:
12 V, 21.0 W
× 2
License plate light:
12 V, 5.0 W
× 1
Meter lighting:
LED
Neutral indicator light:
LED
High beam indicator light:
LED
Oil level warning light:
LED
Turn signal indicator light:
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
Fuses:
Main fuse:
50.0 A
Headlight fuse:
20.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
15.0 A
Radiator fan fuse:
10.0 A
× 2
Fuel injection system fuse:
15.0 A
Backup fuse:
10.0 A
9-3
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
EAU26352
Identification numbers
Record the key identification number, vehicle identification number and model label information in the spaces provided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehicle is stolen.
KEY IDENTIFICATION NUMBER:
Key identification number
VEHICLE IDENTIFICATION
NUMBER:
MODEL LABEL INFORMATION:
CONSUMER INFORMATION
EAU26381
Vehicle identification number
EAU26400
1. Key identification number
The key identification number is stamped into the key tag. Record this number in the space provided and use it for reference when ordering a new key.
1. Vehicle identification number
The vehicle identification number is stamped into the steering head pipe.
Record this number in the space provided.
TIP
The vehicle identification number is used to identify your motorcycle and may be used to register your motorcycle with the licensing authority in your area.
10
10-1
10
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
CONSUMER INFORMATION
Model label
EAU26470 EAU48270
Vehicle Emission Control Information label
1
1. Model label
The model label is affixed to the frame
under the rider seat. (See page 4-15.)
Record the information on this label in the space provided. This information will be needed when ordering spare parts from a Yamaha dealer.
1. Vehicle Emission Control Information label
The Vehicle Emission Control Information label is affixed at the location in the illustration. This label shows specifications related to exhaust emissions as required by federal law, state law and
Environment Canada.
10-2
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
CONSUMER INFORMATION
EAU26551
Reporting safety defects
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation,
U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your dealer, or Yamaha Motor Corporation, U.S.A.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also obtain other information about motor vehicle safety from http://www.safercar.gov.
10
10-3
10
U1CA11E0.book Page 4 Thursday, September 23, 2010 11:51 AM
CONSUMER INFORMATION
EAU26560
Motorcycle noise regulation
TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:
Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person.
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.
These acts include tampering with the following systems; i.e., modification, removal, etc.
Exhaust system
• Muffler
• Exhaust pipe
• Silencer
Intake system
• Air cleaner case
• Air cleaner element
• Intake duct
10-4
U1CA11E0.book Page 5 Thursday, September 23, 2010 11:51 AM
CONSUMER INFORMATION
EAU26632
Maintenance record
Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder that maintenance work is required. It is not acceptable proof of maintenance work.
Date of service
Mileage
Servicing dealer name and address
Remarks
Maintenance interval
600 mi
(1000 km) or
1 month
4000 mi
(7000 km) or
6 months
8000 mi
(13000 km) or
12 months
12000 mi
(19000 km) or
18 months
16000 mi
(25000 km) or
24 months
20000 mi
(31000 km) or
30 months
24000 mi
(37000 km) or
36 months
28000 mi
(43000 km) or
42 months
32000 mi
(49000 km) or
48 months
10-5
10
10
U1CA11E0.book Page 6 Thursday, September 23, 2010 11:51 AM
CONSUMER INFORMATION
Maintenance interval
36000 mi
(55000 km) or
54 months
40000 mi
(61000 km) or
60 months
Date of service
Mileage
Servicing dealer name and address
Remarks
10-6
U1CA11E0.book Page 7 Thursday, September 23, 2010 11:51 AM
CONSUMER INFORMATION
YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED
EAU26663
WARRANTY
Yamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha motorcycles will be free from defects in material and workmanship for the period of time stated herein, subject to certain stated limitations.
THE PERIOD OF WARRANTY for Yamaha motorcycles originally equipped with headlight, stoplight, and turn signals shall be one (1) year from the date of purchase, with no mileage limitation.
THE CUSTOMER’S RESPONSIBILITY under this warranty shall be to:
1.
Operate and maintain the motorcycle as specified in
2.
the appropriate Owner’s Manual, and
Give notice to an authorized Yamaha motorcycle dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealer’s place of business.
Engine
Displacement
Under 50cc
50cc to 169cc
170cc to 279cc
MODELS EXCLUDED FROM WARRANTY include those used for non-Yamaha-authorized renting, leasing or other commercial purposes, and TZ models.
DURING THE PERIOD OF WARRANTY, any authorized
Yamaha motorcycle dealer will, free of charge, repair or replace any part adjudged defective by Yamaha due to faulty workmanship or material from the factory. Parts used in warranty repairs will be warranted for the balance of the product’s warranty period. All parts replaced under warranty become property of Yamaha Motor Corporation,
U.S.A.
WARRANTY TRANSFER: To transfer the warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha motorcycle dealer.
In order for this warranty to remain in effect, this inspection and registration must take place within ten
(10) days after transfer. An inspection and registration fee will be charged for this service.
GENERAL EXCLUSIONS from this warranty shall include any failures caused by: a) b) c) d) e) f)
Competition or racing use.
Installation of parts or accessories that are not qualitatively equivalent to genuine Yamaha parts.
Abnormal strain, neglect, or abuse.
Lack of proper maintenance.
Accident or collision damage.
Modification to original parts.
EMISSION CONTROL SYSTEM WARRANTY:
Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha motorcycle covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the period listed immediately below. Failures other than those resulting from defects in material or workmanship, which arise solely as a result of owner abuse and/or lack of proper maintenance, are not covered by this warranty.
SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance.
280cc and over
Period
6,000 km (3,750 miles) or five years, whichever occurs first
12,000 km (7,465 miles) or five years whichever occurs first
18,000 km (11,185 miles) or five years, whichever occurs first
30,000 km (18,641 miles) or five years, whichever occurs first
YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO
OTHER WARRANTY OF ANY KIND, EXPRESSED OR
IMPLIED. ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE WHICH EXCEED THE
OBLIGATIONS AND TIME LIMITS STATED IN THIS
WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA
MOTOR CORPORATION, U.S.A. AND EXCLUDED
FROM THIS WARRANTY.
SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU. ALSO
EXCLUDED FROM THIS WARRANTY ARE ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING LOSS OF USE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
YAMAHA MOTOR CORPORATION, U.S.A.
P.O. Box 6555
Cypress, California 90630
10
10-7
U1CA11E0.book Page 8 Thursday, September 23, 2010 11:51 AM
CONSUMER INFORMATION
10
WARRANTY QUESTIONS AND ANSWERS
Q.
A.
What costs are my responsibility during the warranty period?
The customer’s responsibility includes all costs of normal maintenance services, non-warranty repairs, accident and collision damages, and oil, oil filters, air filters, spark plugs, and brake shoes.
Q.
A.
What are some examples of “abnormal” strain, neglect, or abuse?
These terms are general and overlap each other in areas. Specific examples include: Running the machine out of oil, sustained high rpm, full-throttle, operating the machine with a broken or damaged part which causes another part to fail, damage or failure due to improper or careless transportation and/or tie-down. If you have any specific questions on operation or maintenance, please contact your dealer for advice.
Q.
A.
Does the warranty cover incidental costs such as towing or transportation due to a failure?
No. The warranty is limited to repair of the machine itself.
Q.
A.
May I perform any or all of the recommended maintenance shown in the Owner’s
Manual instead of having the dealer do them?
Yes, if you are a qualified mechanic and follow the procedures specified in the
Owner’s and Service Manual. We do recommend, however, that items requiring special tools or equipment be done by a Yamaha motorcycle dealer.
Q.
A.
Will the warranty be void or cancelled if I do not operate or maintain my new motorcycle exactly as specified in the Owner’s Manual?
No. The warranty on a new motorcycle cannot be “voided” or “cancelled.” However, if a particular failure is caused by operation or maintenance other than as described in the Owner’s Manual, that failure may not be covered under warranty.
Q.
A.
What responsibility does my dealer have under this warranty?
Each Yamaha motorcycle dealer is expected to:
1.
Completely set up every new machine before sale.
2.
Explain the operation, maintenance, and warranty requirements to your satisfaction at the time of sale, and upon your request at any later date.
3.
Each Yamaha motorcycle dealer is held responsible for his setup, service and warranty repair work.
Q.
A.
Is the warranty transferable to second owners?
Yes. The remainder of the existing warranty can be transferred upon request. The unit has to be inspected and re-registered by an authorized Yamaha motorcycle dealer for the policy to remain effective.
CUSTOMER SERVICE
If your machine requires warranty service, you must take it to any authorized Yamaha motorcycle dealer within the continental United States. Be sure to bring your warranty registration card or other valid proof of the original date of purchase. If a question or problem arises regarding the warranty, first contact the owner of the dealership. Since all warranty matters are handled at the dealer level, this person is in the best position to help you. IF you are still not satisfied and require additional assistance, please write to:
YAMAHA MOTOR CORPORATION, U.S.A.
CUSTOMER RELATIONS DEPARTMENT
P.O. Box 6555
Cypress, California 90630
When contacting Yamaha Motor Corporation, U.S.A., don’t forget to include any important information such as names, addresses, model, V.I.N. (frame number), dates, and receipts.
CHANGE OF ADDRESS
The federal government requires each manufacturer of a motor vehicle to maintain a complete, up-to-date list of all first purchasers against the possibility of a safetyrelated defect and recall. This list is compiled from the purchase registrations sent to
Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.
If you should move after you have purchased your new motorcycle, please advise us of your new address by sending a postcard listing your motorcycle model name, V.I.N.
(frame number), dealer number (or dealer’s name) as it is shown on your warranty card, your name and new mailing address. Mail to:
YAMAHA MOTOR CORPORATION, U.S.A.
P.O. Box 6555
Cypress, California 90630
Attention: Warranty Department
This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.
10-8
U1CA11E0.book Page 9 Thursday, September 23, 2010 11:51 AM
CONSUMER INFORMATION
EAU26750
YAMAHA EXTENDED SERVICE (Y.E.S.)
Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.).
Y.E.S. is designed and administered by Yamaha Motor
Corporation to provide maximum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.
Y.E.S. is flexible. You choose the plan that’s right for you: 12 months, 24 months, 36 months or, on certain models, even 48 months beyond your warranty period.
Y.E.S. is designed and administered by the same
Yamaha people who handle your warranty – and it shows in the comprehensive coverage benefits. There are no mileage limitations. Coverage isn’t limited to
“moving parts” or the “drive train” like many other plans.
And Y.E.S. covers manufacturing defects just like the warranty. See the sample contract at your Yamaha dealer to see how comforting uninterrupted factorybacked protection can be.
You don’t have to pay anything for covered repairs.
There’s no deductible to pay, and repairs aren’t
“pro-rated.” You don’t have any “out-of-pocket” expenses for covered repairs.
In addition, Travel and Recreation Interruption Protection
(TRIP) is included at no extra cost. TRIP gives you up to
$150 reimbursement per occurrence for any reasonable expenses you incur because your Yamaha needs covered service: replacement vehicle rental, emergency towing, phone calls, even food and lodging when you are away from home. This superb coverage goes into effect when you purchase Y.E.S., so it applies to any warranty repairs as well as covered repairs during your entire
Y.E.S. plan period.
Y.E.S. coverage is honored at any authorized Yamaha dealer nationwide.
Y.E.S. coverage is transferable to a new owner if you sell or trade-in. That can make your Yamaha much more valuable!
This excellent Y.E.S. plan coverage is only available to
Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha
Extended Service.
10
10-9
10
U1CA11E0.book Page 10 Thursday, September 23, 2010 11:51 AM
CONSUMER INFORMATION
We urge you to act now. You’ll get the excellent benefits of
TRIP coverage right away, and you’ll rest easy knowing you’ll have strong factory-backed protection even after your
Yamaha Limited Warranty expires.
A special note:
If visiting your dealer isn’t convenient, contact Yamaha with your Primary ID number (your frame number). We’ll be happy to help you get the Y.E.S. coverage you need.
Yamaha Service Marketing
P.O. Box 6555
Cypress, CA 90630
1-(866)-YES-EXTD (1-866-937-3983)
10-10
U1CA11E0.book Page 1 Thursday, September 23, 2010 11:51 AM
A
B
Air filter element, replacing ................... 7-15
C
Battery .................................................. 7-31
Brake and clutch levers, checking and lubricating..................... 7-28
Brake and shift pedals, checking and lubricating..................... 7-27
Brake fluid, changing ............................ 7-24
Brake fluid level, checking .................... 7-23
Brake lever ........................................... 4-11
Brake lever free play, checking ............ 7-22
Brake light switches.............................. 7-22
Brake pedal .......................................... 4-11
Cables, checking and lubricating .......... 7-27
Canister (for California only)................. 7-11
Care ........................................................ 8-1
Catalytic converters .............................. 4-14
Centerstand and sidestand, checking and lubricating..................... 7-29
Clutch lever........................................... 4-10
Clutch lever free play, adjusting ........... 7-21
Coolant ................................................. 7-14
Coolant temperature warning light.......... 4-3
D
E
Dimmer switch ........................................ 4-9
Drive chain, cleaning and lubricating .... 7-26
Drive chain slack .................................. 7-25
Engine break-in ...................................... 6-3
Engine idling speed, checking .............. 7-17
Engine oil and oil filter cartridge ........... 7-11
Engine stop switch.................................. 4-9
F
Engine trouble warning light ....................4-5
EXUP system ........................................4-21
I
Front and rear brake pads, checking ....7-23
Front fork, adjusting ..............................4-17
Front fork, checking...............................7-29
Fuel .......................................................4-12
Fuel tank breather/overflow hose ..........4-13
Fuel tank cap.........................................4-11
Fuses, replacing ....................................7-32
H
Handlebar switches .................................4-9
Hazard switch........................................4-10
Headlight bulb, replacing.......................7-34
High beam indicator light.........................4-2
Horn switch .............................................4-9
K
Key identification number......................10-1
L
Identification numbers ...........................10-1
Ignition circuit cut-off system .................4-22
Indicator lights and warning lights ...........4-2
M
Labels, location .......................................1-1
License plate light bulb, replacing .........7-36
Luggage strap holders ..........................4-20
Main switch/steering lock ........................4-1
Maintenance and lubrication, periodic.....7-5
Maintenance, emission control system ...7-3
Maintenance record ..............................10-5
Matte color, caution .................................8-1
Model label ............................................10-2
Multi-function meter unit..........................4-5
INDEX
N
O
Oil level warning light .............................. 4-2
P
Neutral indicator light .............................. 4-2
Noise regulation .................................... 10-4
S
Panels, removing and installing .............. 7-9
Parking.................................................... 6-4
Part locations .......................................... 3-1
T
Safety defects, reporting....................... 10-3
Safety information ................................... 2-1
Seats..................................................... 4-15
Shifting.................................................... 6-2
Shift pedal ............................................. 4-10
Shock absorber assembly, adjusting .... 4-19
Sidestand.............................................. 4-21
Spark plugs, checking........................... 7-10
Specifications.......................................... 9-1
Starting the engine.................................. 6-1
Start switch ........................................... 4-10
Steering, checking ................................ 7-30
Storage ................................................... 8-3
Storage compartment ........................... 4-16
Tail/brake light bulb, replacing .............. 7-35
Throttle grip and cable, checking and lubricating ..................... 7-27
Throttle grip free play, checking............ 7-18
Tires...................................................... 7-18
Tool kit .................................................... 7-2
Troubleshooting .................................... 7-39
Troubleshooting charts ......................... 7-41
Turn signal indicator lights ...................... 4-2
U1CA11E0.book Page 2 Thursday, September 23, 2010 11:51 AM
INDEX
V
Turn signal light bulb, replacing ............ 7-35
Turn signal switch ................................... 4-9
Valve clearance .................................... 7-18
Vehicle Emission Control Information label .................................................... 10-2
Vehicle identification number ................ 10-1
W
Warranty, extended............................... 10-9
Warranty, limited ................................... 10-7
Wheel bearings, checking..................... 7-30
Wheel (front) ......................................... 7-36
Wheel (rear) .......................................... 7-38
Wheels .................................................. 7-21
U1CA11E0.book Page 3 Thursday, September 23, 2010 11:51 AM
PRINTED ON RECYCLED PAPER
YAMAHA MOTOR CO., LTD.
PRINTED IN JAPAN
2010.10-0.3
×1 CR
(E)
DIC183

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Catalytic converter system
- EXUP system
- 6-speed transmission
- Fuel injection system
- Passenger seat
- Fuel reserve tripmeter
- Self-diagnosis device
- LCD and tachometer brightness control
- Multi-function meter unit
- Ignition circuit cut-off system