Registering Devices with the Cisco Prime NSC Registering a Cisco VSG

Registering Devices with the Cisco Prime NSC Registering a Cisco VSG
Registering Devices with the Cisco Prime NSC
This chapter contains the following sections:
• Registering a Cisco VSG, page 1
• Registering Cisco Nexus 1000V VSM , page 2
Registering a Cisco VSG
You can register Cisco VSG with Cisco Prime NSC. Registration enables communication between the Cisco
VSG and the Cisco Prime NSC.
Step 1
Copy the vsghv-pa.2.1.1e.bin file into the Cisco VSG bootflash:
vsg# copy ftp://guest@172.18.217.188/n1kv/vsghv-pa.2.1.1e.bin bootflash
Step 2
Enter global configuration mode.
vsg# configure
Step 3
Enter nsc-policy-agent mode.
vsg (config)# nsc-policy-agent
Step 4
Set the Cisco Prime NSC registration IP address.
vsg (config-nsc-policy-agent)# registration-ip 209.165.200.225
Step 5
Specify the shared-secret of Cisco Prime NSC.
vsg (config-nsc-policy-agent)#
shared-secret ********
Step 6
Install the policy agent.
vsg (config-nsc-policy-agent)#
policy-agent-image bootflash: vsghv-pa.2.1.1e.bin
Step 7
Exit all modes.
vsg (config-nsc-policy-agent)# end
Step 8
On the Cisco VSG command line, display the NSC PA status:
vsg# show nsc-pa status
If registration was successful, you should see the following message:
"NSC Policy-Agent status is - Installed Successfully. Version 2.1(1b)-vsg"
The Cisco VSG registration is complete.
Cisco VSG for Microsoft Hyper-V, Release 5.2(1)VSG2(1.1b) and Cisco Prime NSC, Release 3.2 Installation and
Upgrade Guide
OL-28943-02
1
Registering Devices with the Cisco Prime NSC
Registering Cisco Nexus 1000V VSM
Step 9
Copy the running configuration to the startup configuration:
vsg# copy running-config startup-config
Executing this command ensures that the registration becomes part of the basic configuration
Registering Cisco Nexus 1000V VSM
You can register Cisco Nexus 1000V with Cisco Prime NSC. Registration enables communication between
the Cisco Nexus 1000V VSM and Cisco Prime NSC.
SUMMARY STEPS
1.
2.
3.
4.
5.
6.
7.
8.
9.
Copy the vsmhv-pa.3.2.1c.bin file into the VSM bootflash:
Enter global configuration mode.
Enter config nsc-policy-agent mode.
Set the Cisco Prime NSC registration IP address.
Specify the shared-secret of Cisco Prime NSC.
Install the policy agent.
Exit all modes.
Display the NSC PA status:
Copy the running configuration to the startup configuration:
DETAILED STEPS
Step 1
Copy the vsmhv-pa.3.2.1c.bin file into the VSM bootflash:
vsm# copy ftp://guest@172.18.217.188/n1kv/vsmhv-pa.3.2.1c.bin bootflash:
Step 2
Enter global configuration mode.
vsg# configure
Step 3
Enter config nsc-policy-agent mode.
vsg(config)# nsc-policy-agent
Step 4
Set the Cisco Prime NSC registration IP address.
vsg(config-nsc-policy-agent)# registration-ip 209.165.200.226
Step 5
Specify the shared-secret of Cisco Prime NSC.
vsg(config-nsc-policy-agent)# shared-secret ********
Step 6
Install the policy agent.
vsg(config-nsc-policy-agent)# policy-agent-image bootflash:vsmhv-pa.3.2.1c.bin
Step 7
Exit all modes.
vsg(config-nsc-policy-agent)# top
Step 8
Display the NSC PA status:
vsg# show nsc-pa status
If registration was successful, you should see the following message:
NSC Policy-Agent status is - Installed Successfully. Version 2.1(1b)-vsg
The Cisco Nexus 1000V VSM registration is complete.
Cisco VSG for Microsoft Hyper-V, Release 5.2(1)VSG2(1.1b) and Cisco Prime NSC, Release 3.2 Installation and
Upgrade Guide
2
OL-28943-02
Registering Devices with the Cisco Prime NSC
Registering Cisco Nexus 1000V VSM
Step 9
Copy the running configuration to the startup configuration:
vsg# copy running-config startup-config
Executing this command ensures that the registration becomes part of the basic configuration.
What to Do Next
See the Cisco Virtual Management Center CLI Configuration Guide for detailed information about configuring
the Cisco Prime NSC using the CLI.
Cisco VSG for Microsoft Hyper-V, Release 5.2(1)VSG2(1.1b) and Cisco Prime NSC, Release 3.2 Installation and
Upgrade Guide
OL-28943-02
3
Registering Devices with the Cisco Prime NSC
Registering Cisco Nexus 1000V VSM
Cisco VSG for Microsoft Hyper-V, Release 5.2(1)VSG2(1.1b) and Cisco Prime NSC, Release 3.2 Installation and
Upgrade Guide
4
OL-28943-02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising