Fujitsu LifeBook V Series BIOS Guide LifeBook V Series Model:

Fujitsu LifeBook V Series BIOS Guide LifeBook V Series Model:
Fujitsu LifeBook
V Series
BIOS Guide
LifeBook V Series Model:
V1010
Document Date: 09/20/2007
Document Part Number: FPC58-1782-01
FUJITSU COMPUTER SYSTEMS CORPORATION
1
LifeBook V Series Notebook BIOS
V Series BIOS
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the
operating environment for your notebook. Your BIOS
is set at the factory for normal operating conditions,
therefore there is no need to set or change the BIOS
environment to operate your notebook.
The BIOS Setup Utility configures:
■
■
Device control feature parameters, such as changing
I/O addresses and boot devices.
System Data Security feature parameters, such
as passwords.
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility, do the following (or use
the TrustedCore Menu, as detailed in the next section):
1. Turn on or restart your notebook.
2. Press [F2] once the Fujitsu logo appears on the
screen. This will open the main menu of the BIOS
Setup Utility with the current settings displayed.
3. Press the [RIGHT ARROW] or [LEFT ARROW] key
to scroll through the other setup menus to review or
alter the current settings.
Using the TrustedCore Menu
When the Fujitsu logo appears on the screen. press the
[Enter] key or click on the left mouse or touchpad
button; the TrustedCore Menu will appear.
The TrustedCore Menu provides shortcuts to the
following menus and information screens:
■
■
■
■
■
■
BIOS Setup
Diagnostic Screen
Boot Menu
Patent Information
System Information
Continue Booting
Navigating through the Setup Utility
The BIOS setup utility consists of six menus: Info,
System, Advanced, Security, Boot, and Exit. This document explains each menu in turn, including all
submenus and setup items.
The following procedures allow you to navigate the
setup utility menus:
], [
]
1. To select a menu, use the cursor keys: [
2. To select a field within a menu or a submenu, use the
cursor keys: [ ], [ ].
3. To select the different values for each field, press the
[Spacebar] or [+] to change to the next lower
selection and [F5] or [-] to go to the next higher
selection.
4. To activate a submenu press the [Enter] key.
5. To return to a menu from a submenu, press the [Esc]
key.
6. To go to the Exit menu from any other menu,
press the [Esc] key.
■
Selecting a field causes a help message
about that field to be displayed on the
right-hand side of the screen.
■
Pressing the Enter key with the highlight
on a selection that is not a submenu or
auto selection will cause a list of all
options for that item to be displayed.
Pressing the Enter key again will select
the highlighted choice.
7. Pressing the [F9] key resets all items in the BIOS to
the default values.
8. Pressing the [F10] key saves the current configuration and exits the BIOS Setup Utility. You will be
asked to verify this selection before it is executed.
9. Pressing the [F1] key gives you a general help screen.
Clicking on any of the fields will invoke the screen,
information, or action described.
Entering the Setup Utility After a Configuration
Change or System Failure
The Boot Menu can also be invoked by pressing the
[F12] key when the Fujitsu logo appears on the screen.
If there has been a change in the system configuration
that does not agree with the parameter settings stored in
your BIOS memory, or there is a failure in the system,
the system beeps and/or displays an error message after
the Power On Self Test (POST). If the failure is not too
2
BIOS Setup Utility
severe, it will give you an opportunity to modify the
setup utility settings, as described in the following steps:
1. When you turn on or restart the computer there is a
beep and/or the following message appears on the
screen:
Error message - please run SETUP
program Press <F1> key to continue,
<F2> to run SETUP
2. If an error message is displayed on the screen, and
you want to continue with the boot process and start
the operating system anyway, press the [F1] key.
■
If your notebook emits a series of beeps
that sounds like a code and the display is
blank, please refer to the Troubleshooting Section in the system User’s Guide.
The Troubleshooting Section includes a
list of error messages and their meanings.
■
If your data security settings require it,
you may be asked for a password before
the operating system will be opened.
3. If an error message is displayed on the screen, and
you want to enter the setup utility, press the [F2] key.
4. When the setup utility starts with a fault present, the
system displays the following message:
Warning!
Error message
[Continue]
5. Press any key to enter the setup utility. The system
will then display the Info Menu with current parameters values.
3
LifeBook V Series Notebook BIOS
MAIN MENU – SETTING STANDARD SYSTEM PARAMETERS
The Main Menu allows you to set or view the current
system parameters. Follow the instructions for Navigating Through The Setup Utility to make any changes.
(See Navigating through the Setup Utility on page 2 for
more information.)
the field’s function and any special information needed
to help understand the field’s use.
System Time and System Date can also be
set from your operating system without
using the setup utility. Use the Date and
Time icon on your Windows Control panel
or type time or date from the MS-DOS
prompt.
The following tables show the names of the menu fields
for the Main menu and its submenus, all of the options
for each field, the default settings and a description of
Main
Advanced
PhoenixBIOS Setup Utility
Security
Boot
Info
Exit
Item Specific Help
System Time:
System Date:
[14:57:01]
[09/20/2007]
Adjust calendar clock.
▲ ▲
Drive0
Drive1
[FUJITSU MHV2080BH]
[HL-DT-ST DVDRAM_GSA-T20N]
Language:
[English (US)]
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
<Tab>, <Shift-Tab>, or
<Enter> selects field.
F9
F10
Setup Defaults
Save and Exit
Figure 1. Main Menu
Table 1: Fields, Options and Defaults for the Main Menu
Note that the parameters listed in the following table may vary depending upon your system’s configuration.
4
Menu Field
Options
Default
Description
System Time:
–—
–—
Sets and displays the current time. Time is in a 24 hour format
of hours:minutes:seconds with 2 digits for each. (HH:MM:SS).
Example: 16:45:57. You may change each segment of the time
separately. Move between the segments with the [Tab] key and/
or [Shift] + [Tab] keys.
System Date:
–—
–—
Sets and displays the current date. Date is in a month/day/year
numeric format with 2 digits each for month and day and 4 digits
for year. (MM/DD/YYYY) for example: 03/20/2006. You may
change each segment of the date separately. Move between the
segments with the [Tab] key and/or [Shift] + [Tab] keys.
Main Menu
Table 1: Fields, Options and Defaults for the Main Menu
Note that the parameters listed in the following table may vary depending upon your system’s configuration.
Menu Field
Options
Default
Description
Drive0
Selects Drive0
submenu
The product number of
the hard drive.
Display the type of device on this ATA/ATAPI interface, if there is
one. Pressing the Enter key selects the Drive0 submenu allowing
additional device configuration options for this interface.
Drive1
Selects Drive1
submenu
The product number of
the CD-ROM drive.
Display the type of device on this ATA/ATAPI interface, if there is
one. Pressing the Enter key selects the Drive1 submenu allowing
additional device configuration options for this interface
Language:
■
[English (US)]
The default setting differs between the US/European and the
Japanese model. Selects the display language for the BIOS. (Note
that this field may appear blank until the first time it is selected.)
■
English (US)
Japanese (JP)
5
LifeBook V Series Notebook BIOS
Drive0 Submenu of the Main Menu
The Drive0 submenu identifies what ATA devices are installed.
PhoenixBIOS Setup Utility
Main
Drive0 [FUJITSU MHV2080BH]
Type:
Item Specific Help
Select Serial ATA/ATAPI
drive installed here.
[Auto]]
LBA Format
156301488
80026MB SATA1
Total Sectors:
Maximum Capacity:
[Auto]
The BIOS auto-types the
drive on boot time.
[None]
The drive is disabled.
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 2. Drive0 Submenu
Table 2: Fields, Options and Defaults for the Drive0 Submenu of the Main Menu
Menu Field
Options
Default
Description
Type:
■
[Auto]
Automatically selects the ATA/ATAPI device type. To change the
selection, press the spacebar. Select Auto to have the type automatically identified by the BIOS at POST. Select None if you don’t want
to select a primary master.
■
Auto
None
LBA Format
6
Logical Block Addressing (LBA)
Total Sectors:
---
---
The total number of sectors on your hard disk
Maximum
Capacity:
---
---
The maximum capacity of your hard disk
Main Menu
Drive1 Submenu of the Main Menu
The Drive1 submenu allows you to configure secondary ATA devices, such as an optical drive.
PhoenixBIOS Setup Utility
Main
Drive1 [HL-DT-ST DVDRAM_GSA-T20N]
Type:
[Auto]
Multi-Sector Transfers:
LBA Mode Control:
Transfer Mode:
Ultra DMA Mode:
[Disabled]
[Disabled]
[Standard]
[Disabled]
Item Specific Help
Select Serial ATA/ATAPI
drive installed here.
[Auto]
The BIOS auto-types the
drive on boot time.
[None]
The drive is disabled.
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 3. Drive1 Submenu
Table 3: Fields, Options and Defaults for the Drive1 Submenu of the Main Menu
Menu Field
Options
Default
Description
Type:
■
[Auto]
NOTE: The Type field does not appear as a drop-down menu. Tap
the spacebar to cycle through the selections.
■
Auto
None
Selects the ATA/ATAPI device type. Select Auto to have the type
automatically identified by the BIOS at POST. If None is selected, all
of the following Set-up items do not appear.
Multi-Sector
Transfers:
■
■
■
■
■
LBA Mode
Control:
■
■
Disabled
2 Sectors
4 Sectors
8 Sectors
16 Sectors
[Disabled]
This option cannot be changed when Auto is selected. Specify the
number of sectors per block for multiple sector transfer.
Disabled
Enabled
[Disabled]
Enables or disables Logical Block Addressing in place of Cylinder,
Head, Sector addressing. This option cannot be changed when Auto
is selected.
7
LifeBook V Series Notebook BIOS
Table 3: Fields, Options and Defaults for the Drive1 Submenu of the Main Menu
Menu Field
Options
Default
Description
Transfer Mode:
■
Standard
Fast PIO 1
Fast PIO 2
Fast PIO 3
Fast PIO 4
Multiword DMA 1
Multiword DMA 2
[Standard]
This option cannot be changed when Auto is selected.Selects the
method for moving data to/from the drive. Autotype the drive to
select the optimum transfer mode. Multiword DMA is automatically
set to mode 1 for Fast PIO 1, Fast PIO 2, Fast PIO 3, and set to
mode 2 for Fast PIO 4 / DMA.
Disabled
Mode 0
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
[Disabled]
This option cannot be changed when Auto is selected. Selects the
method for moving data to/from the drive. Autotype the drive to
select the optimum transfer mode.
■
■
■
■
■
■
Ultra DMA
Mode:
■
■
■
■
■
■
■
8
Advanced Menu
ADVANCED MENU – SETTING DEVICE FEATURE CONTROLS
The Advanced Menu allows you to:
■
■
■
■
■
Set the keyboard and mouse features.
Select between the display panel and an external CRT
display or video projector.
Enable or disable compensation for your display.
Enables or disables the internal controllers.
Configure CPU and USB features in your system.
Main
Advanced
Follow the instructions for Navigating Through the
Setup Utility to make any changes.
The following tables show the names of the menu fields
for the Advanced Menu and its submenus, all of the
options for each field, the default settings and a description of the field’s function and any special information
needed to help understand the field’s use.
PhoenixBIOS Setup Utility
Security
Boot Info
Exit
Item Specific Help
▲ ▲ ▲ ▲ ▲ ▲
Keyboard/Mouse Features
Video Features
Internal Device Configurations
CPU Features
USB Features
Miscellaneous Configurations
▲
Event Logging
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Configures keyboard/
mouse features.
F9 Setup Defaults
F10 Save and Exit
Figure 4. Advanced Menu
Table 4: Fields, Options and Defaults for the Advanced Menu
Menu Field
Description
Keyboard/Mouse Features
When selected, opens the Keyboard/Mouse Features submenu, which allows turning NumLock on or off.
Video Features
When selected, opens the Video Features submenu, which allows setting of the display parameters,
including routing of video signals to different displays.
Internal Device
Configurations
When selected, opens the Internal Device Configuration submenu, which allows enabling or disabling the
Serial ATA, IDE, and LAN Controllers.
CPU Features
When selected, opens the CPU Features submenu to allow you to enable or disable the SpeedStep® Technology feature and XD Bit functionality.
USB Features
When selected, opens the USB Features submenu to allow you to enable or disable the legacy support and
SCSI SubClass support (e.g., floppy disk drive, external optical drive).
9
LifeBook V Series Notebook BIOS
Table 4: Fields, Options and Defaults for the Advanced Menu
Menu Field
Description
Miscellaneous
Configurations
When selected, opens the Miscellaneous Configurations submenu to allow you to enable or disable the
power button and the Wake Up On LAN feature, and to set the Volume Setting.
Event Logging
When selected, opens the event logging submenu.
10
Advanced Menu
Keyboard/Mouse Features Submenu of the Advanced Menu
The Keyboard Features submenu is for enabling or disabling the NumLock feature.
Main
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Advanced
Keyboard/Mouse Features
Numlock:
Item Specific Help
[On] or [Off]
Numlock in On or Off.
[Off]
* Windows XP preserves
Numlock state when the
user logs off.
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 5. Keyboard Features Submenu
Table 5: Fields, Options and Defaults for the Keyboard Submenu of the Advanced Menu
Menu Field
Options
Default
Description
Numlock:
■
[Off]
Sets the NumLock function state when the computer completes
booting.
■
On
Off
11
LifeBook V Series Notebook BIOS
Video Features Submenu of the Advanced Menu
The Video Features Submenu is for setting the display parameters.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Item Specific Help
Video Features
Display:
Compensation:
[Auto]
[Enabled]
Select display terminal.
* This setting is not
effective after
operating system
starts up.
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 6. Video Features Submenu
Table 6: Fields, Options and Defaults for the Video Features Submenu of the Advanced Menu
Menu Field
Options
Default
Description
Display:
■
Internal Flat Panel
External
Auto
[Auto]
Selects where the video signal will be routed.
Note: The Windows video driver overrides this setting.
Disabled
Enabled
[Enabled]
Enables or disables compensation which controls spacing on the
display. When enabled, displays with less than pixel resolution
1024 x 768 or 800 x 600 will still cover the entire screen. A resolution below 800 x 600 will fill the screen, but due to the low resolution, will appear blocky and may not be acceptable.
■
■
Compensation:
■
■
12
Advanced Menu
Internal Device Configurations Submenu of the Advanced Menu
The Internal Device Configuration submenu allows the user to configure other internal devices.
Main
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Advanced
Item Specific Help
Internal Devices Configurations
Serial ATA Controller:
AHCI Configuration:
IDE Controller:
LAN Controller:
Wireless LAN:
Select Item
Select Menu
[Enabled]
Serial ATA port is
enabled.
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
[Disabled]
Serial ATA port is
disabled.
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
F9 Setup Defaults
F10 Save and Exit
Figure 7. Internal Device Configuration Submenu
Table 7: Fields, Options and Defaults for the Internal Device Configuration Submenu of the Advanced Menu
Menu Field
Options
Default
Description
Serial ATA Controller:
■
Disabled
Enabled
[Enabled]
Enables or disables the Serial ATA port.
Disabled
Enabled
[Enabled]
Enables or disables the AHCI (Advanced Host Controller Interface).
Disabled
Enabled
[Enabled]
Enables or disables selected IDE devices.
Disabled
Enabled
[Enabled]
Enables or disables the LAN controller.
Disabled
Enabled
[Enabled]
Enables or disables the Wireless LAN controller.
■
AHCI Configuration:
■
■
IDE Controller:
■
■
LAN Controller:
■
■
Wireless LAN:
■
■
13
LifeBook V Series Notebook BIOS
CPU Features Submenu of the Advanced Menu
The CPU Features Submenu provides options for enabling or disabling the SpeedStep® Technology feature.
Main
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Advanced
CPU Features
Item Specific Help
Core Multi-Processing:
[Enabled]
SpeedStep(R) Technology:
On Battery:
On AC:
[Enabled]
[Battery Optimized]
[Maximum Performance]
XD Bit functionality:
[Enabled]
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Select Core
Multi-Processing
enabled or disabled.
F9 Setup Defaults
F10 Save and Exit
Figure 8. CPU Features Submenu
Table 8: Fields, Options and Defaults for the CPU Features Submenu of the Advanced Menu
Menu Field
Options
Default
Description
Core MultiProcessing
■
Disabled
Enabled
[Enabled]
Enables or disables the multi-processing functionality of the
Core processor.
SpeedStep®
Technology:
■
Disabled
Enabled
[Enabled]
When Enabled is selected, CPU speed and battery use can be
selected from On Battery and On AC. When Disabled is
selected, SpeedStep Technology is disabled.
Maximum
Performance
Battery Optimized
Automatic
[Battery
Optimized]
When Maximum Performance is selected, CPU speed is maximized. When Battery Optimized is selected, CPU power requirements are optimized for battery operation. When Automatic is
selected, CPU speed is determined by the power source used.
Maximum
Performance
Battery Optimized
Automatic
[Maximum
Performance]
When Maximum Performance is selected, CPU speed is maximized. When Battery Optimized is selected, CPU power requirements are optimized for battery operation. When Automatic is
selected, CPU speed is determined by the power source used.
On Battery:
■
■
■
■
■
On AC:
■
■
■
14
Advanced Menu
Table 8: Fields, Options and Defaults for the CPU Features Submenu of the Advanced Menu
Menu Field
Options
Default
Description
XD Bit
functionality:
■
[Enabled]
Allows the user to enable and disable the Execute Disable Bit
functionality. Execute Disable Bit allows the processor to classify
areas in memory where application code can and cannot
execute. In the event an internet worm attempts to insert code
in the buffer, the processor disables code execution to prevent
damage or worm propagation.
■
Disabled
Enabled
15
LifeBook V Series Notebook BIOS
USB Features Submenu of the Advanced Menu
The USB Features Submenu provides options for enabling or disabling legacy USB support.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
USB Features
Item Specific Help
[Disabled]
The feature is disabled.
[Enabled]
[Enabled]
Legacy USB Support:
SCSI SubClass Support:
[Enabled]
Legacy USB Emulation
is enabled and USB
devices are available
without USB aware OS.
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 9. USB Features Submenu
Table 9: Fields, Options and Defaults for the USB Features Submenu of the Advanced Menu
Menu Field
Options
Legacy USB Support:
■
■
SCSI SubClass Support:
■
■
16
Default
Description
Disabled
Enabled
[Enabled]
When Enabled is selected, Legacy USB Emulation is enabled and
the USB devices are available without a USB-aware OS. When
Disabled is selected, Legacy USB support is disabled.
Disabled
Enabled
[Enabled]
When Enabled is selected, USB devices that belong to the SCSI
subclass in the mass storage class (e.g., USB Memory Key) are
enabled. Note that enabling this feature may cause the system to
hang during POST, depending on the device that is connected.
Advanced Menu
Miscellaneous Configurations Submenu of the Advanced Menu
The Miscellaneous Configurations Submenu provides options for enabling or disabling the power button and the
Wake Up On LAN or USB features, and for setting the volume.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Miscellaneous Configurations
Power Button:
Wake up on LAN:
Force LAN Boot:
Volume Setting:
UMA Video Memory Size:
Select Item
Select Menu
Configures the power
button.
[Disabled]
[Disabled]
[Disabled]
[Middle]
[128MB]
*ACPI OS ignores this
setting.
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Item Specific Help
F9 Setup Defaults
F10 Save and Exit
Figure 10. Miscellaneous Configurations Submenu
Table 10: Fields, Options and Defaults for the Miscellaneous Configurations Submenu of the Advanced
Menu
Menu Field
Options
Default
Description
Power Button:
■
Disabled
Power Off
[Disabled]
Selecting Disabled disables the power button. Selecting Power Off allows you to
turn off system power with the power button.
Disabled
Enabled
[Disabled]
Selecting Enabled allows the system to wake up when the internal LAN device
receives a signal while in power-off state. Select Disabled to disables the feature.
Disabled
Enabled
[Disabled]
This is only active when Wake up on Lan: is enabled. When enabled, the system
will attempt to boot up from the LAN before attempting to boot from any other
device. This occurs regardless of the BIOS boot priority settings or if Preboot
Execution Environment is disabled.
Off
Minimum
Middle
Maximum
[Middle]
Allows you to set or disable the system volume level.
Note that once the operating system initializes, the volume settings will be
determined by the OS volume settings.
64MB
128MB
224MB
[128MB]
Maximum size allocated for shared video memory. Video memory is dynamically
allocated as needed by Intel(R) Dynamic Video Memory Technology (DVMT).
■
Wake up on LAN:
■
■
Force LAN Boot:
■
■
Volume Setting:
■
■
■
■
UMA Video
Memory Size:
■
■
■
17
LifeBook V Series Notebook BIOS
Event Logging Submenu of the Advanced Menu
The Event Logging Submenu configures event logging features for DMI events.
Main
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Advanced
Item Specific Help
Event Logging
Event Log Capacity:
Event Log Validity:
Space Available
Valid
View Event Log:
[Enter]
Event Logging:
System Boot Event:
[Enabled]
[Disabled]
Clear All Event Logs:
[No]
Mark Events as Read:
[Enter]
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Press <Enter> key to
view the contents of
the event log.
F9 Setup Defaults
F10 Save and Exit
Figure 11. Event Logging Submenu
Table 11: Fields, Options and Defaults for the Event Logging Submenu of the Advanced Menu
Menu Field
Options
Default
Description
Event Log Capacity:
Space Available
Display only
Event Log Validity:
Valid
Display only
View Event Log:
■
Enter
[Enter]
Allows you to view content of event log
Event Logging:
■
Disabled
Enabled
[Enabled]
Turns event logging on and off for all DMI events.
Disabled
Enabled
[Disabled]
Turns event logging on and off for DMI system boot events.
No
Yes
[No]
When set to [Yes] all event logs will be cleared at next boot.
Enter
[Enter]
Allows you to mark all events currently in the event log as having
been read.
■
System Boot Event:
■
■
Clear All Event
Logs:
■
Mark Events as
Read:
■
18
■
Security Menu
SECURITY MENU – SETTING THE SECURITY FEATURES
The Security menu allows you to set up the data security
features of your notebook to fit your operating needs
and to view the current security configuration. Follow
the instructions for navigating through the Setup Utility
to make any changes. (See Navigating through the Setup
Utility on page 2 for more information.)
The following tables show the names of the menu fields
for the Security menu and its submenus, all of the
options for each field, the default settings and a
description of the field's function and any special
information needed to help understand the field's use.
The default condition is no passwords required and no
write protection.
■
If you make an error when re-entering
the password a [Warning] will be displayed on the screen. To try again press
the Enter key and then retype the password. Press the Esc key to abort the
password setting process.
■
Entering a password incorrectly 3 times
in a row will cause the keyboard and
mouse to be locked out and the warning
[System Disabled] to be displayed.
If this happens restart the computer by
turning off and on the power with the
power switch and use the correct password on reboot.
■
If the Power Management Security is
Enabled and the Password on Boot is
Disabled you will not have to type your
password upon resuming the system
from the Standby or Hibernate modes.
Power Management Security will work
only if Password boot is enabled.
If you set a password, write it down and
keep it in a safe place. If you forget the
password you will have to contact your
support representative to regain access to
your secured functions and data.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Boot
Info
Exit
Item Specific Help
▲ ▲
Supervisor Password Is:
User Password Is:
Clear
Clear
Set Supervisor Password
Set User Password
Minimum User Password Length:
Password on Boot:
On Automatic Wake up:
KB Lock on Resume:
Boot from Removable Media:
Flash Write:
Hard Disk Security
Owner Information
[Enter]
[Enter]
[0]
[Disabled]
[Disabled]
[Disabled]
[All]
[Enabled]
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Press <Enter> key to
set Supervisor Password
to enable any password
features.
Then password entry is
required to enter BIOS
Setup.
F9 Setup Defaults
F10 Save and Exit
Figure 12. Security Menu
19
LifeBook V Series Notebook BIOS
Table 12: Fields, Options and Defaults for the Security Menu
Menu Field
Options
Default
Description
Supervisor
Password is:
–—
Clear
A display-only field. Set is displayed when the system supervisor password is set
and Clear when it is not.
User Password is:
–—
Clear
A display-only field. Set is displayed when the general user
password is set, and Clear when it is not.
Set Supervisor
Password
–—
[Enter]
Sets, changes or cancels the Supervisor Password. Supervisor’s Password may
be up to seven characters long and must include only letters or numbers (no
symbols). Passwords are NOT case- sensitive. To cancel a password press the
Enter key instead of entering characters in the Enter New Password field and in
the Re-enter New Password field. When a Supervisor Password is set it must be
used to access the BIOS setup utility.
Set User Password
–—
[Enter]
This field can only be accessed if the Supervisor Password is set. Sets, changes
or cancels the User Password. The User Password may be up to seven characters long and must include only letters or numbers (no symbols). Passwords are
NOT case-sensitive. To cancel a password press the Enter key instead of entering characters in the Enter New Password field and in the Re-enter New Password field. When a User Password is set it must be used to access the BIOS
setup utility.
Minimum User
Password Length:
–—
[0]
Supervisor can set password length (0 to 8) for user password. User cannot set a
password shorter than the minimum length.
Password on Boot:
■
Disabled
First Boot
Every Boot
[Disabled]
When set to First Boot, a password (User or Supervisor) is required just once
after the Power On Self Test (POST) before the operating system will be read
from a disk. When set to Every Boot, a password (User or Supervisor) is required
every time after the Power On Self Test (POST) before the operating system will
be read from a disk. When set to Disabled no password is required.
Disabled
Enabled
[Disabled]
When set to Disabled, it is not necessary to enter a password to wake up from
LAN or Real Time Clock (RTC). When Enabled, it is still necessary to enter a
password after automatic wake-up.
Disabled
Enabled
[Disabled]
When set to Enabled, the PS/2 mouse and keyboard inputs are locked out upon
Resume from Standby or Hibernate mode until you enter the password.
When set to Disabled no password is required. If no Supervisor Password is set,
this feature is not available and no password is required.
All
Supervisor
only
[All]
When All is selected, booting from removable media is not restricted. When
Supervisor Only is selected, only the Supervisor (i.e., the user who enters Supervisor password), can boot from removable media.
Disabled
Enabled
[Enabled]
When set to [Disabled], the BIOS Flash memory is write protected.
■
■
On Automatic
Wake up:
■
KB Lock on
Resume:
■
Boot from
Removable Media:
■
Flash Write:
■
■
■
■
■
Hard Disk Security:
–—
–—
Configures hard disk security features
Owner
Information:
–—
–—
Sets Owner information.
Exiting from the Security Menu
When you have finished setting the parameters on the Security Menu, you can either exit from setup utility or move to
another menu. If you wish to exit from setup utility, press the Esc key to go to the Exit Menu. If you wish to move to
another menu, use the cursor keys.
20
Security Menu
Hard Disk Security Submenu of the Security Menu
The Hard Disk Security Submenu is for configuring hard disk security features.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Hard Disk Security
Drive0:
Set Master Password
Set User Password
Item Specific Help
Clear
[Enter]
[Enter]
Password Entry on Boot: [Enabled]
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 13. Hard Disk Security Submenu
Table 13: Fields, Options and Defaults for the Hard Disk Security Submenu of the Security Menu
Menu Field
Options
Default
Description
Drive0:
---
Clear
The default is Clear. When the Drive0 Password has been set in the field below, the
field changes to Set.
Set Master
Password:
---
[Enter]
When the Master Password has been set, the field can be changed. When enabled,
the hard disk is locked with the password. Data in the locked disk cannot be read on
any systems other than the original system on which it is locked or systems that
have the identical password setting.
Set User
Password
---
[Enter]
When the User Password has been set, the field can be changed. When enabled,
the hard disk is locked with the password. Data in the locked disk cannot be read on
any systems other than the original system on which it is locked or systems that
have the identical password setting.
Password Entry
on Boot:
■
[Enabled]
When disabled, the master password entry is not required before booting the operating system, but the hard disk is still password-protected without password entry.
■
Disabled
Enabled
21
LifeBook V Series Notebook BIOS
Owner Information Submenu of the Security Menu
The Owner Information Submenu is for setting owner information. Note that the owner information cannot be set
without having entered a Supervisor password.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Exit
Owner Information
Owner Information Is:
Clear
Set Owner Information
[Enter]
Foreground Color:
Background Color:
[Gray]
[Black]
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Item Specific Help
F9 Setup Defaults
F10 Save and Exit
Figure 14. Owner Information Submenu
Table 14: Fields, Options and Defaults for the Owner Information Submenu of the Security Menu
Menu Field
Options
Default
Description
Owner Information Is:
–—
Clear
Display only.
Set Owner Information:
–—
[Enter]
Field to write owner
information, (i.e., name).
Foreground Color:
■
Light Cyan
Light Red
Light
Magenta
Yellow
Bright White
[Gray]
Set foreground color.
Light Cyan
Light Red
Light
Magenta
Yellow
Bright White
[Black]
Set background color.
■
■
■
■
■
Background Color:
■
■
■
■
■
■
22
Black
Blue
Green
Cyan
Red
Magenta
■
Black
Blue
Green
Cyan
Red
Magenta
■
■
■
■
■
Brown
White
Gray
Light Blue
Light Green
■
■
■
■
■
■
■
■
■
Brown
White
Gray
Light Blue
Light Green
■
■
■
■
■
Boot Menu
BOOT MENU – SELECTING THE OPERATING SYSTEM SOURCE
The Boot Menu is used to select the order in which the
BIOS searches sources for the operating system. Follow
the instructions for Navigating Through the Setup
Utility to make any changes. (See Navigating through the
Setup Utility on page 2 for more information.)
Main
Advanced
The following tables show the names of the menu fields
for the Boot menu and its submenu, all of the options
for each field, the default settings and a description of
the field's function and any special information needed
to help understand the field's use.
PhoenixBIOS Setup Utility
Security
Power Savings
Boot
▲
Quick Boot:
Boot Time Diagnostic Screen:
Boot Menu:
Preboot Execution Environment:
Boot Device Priority
[Enabled]
[Disabled]
[Enabled]
[Enabled]
Item Specific Help
[Disabled]
All diagnostic tests
will be done.
[Enabled]
Some diagnostic tests
may be skipped while
booting to speed up.
Select Item -/Space Change Values
Select Sub-Menu
Select Menu Enter
▲
F1 Help
ESC Exit
F9 Setup Defaults
F10 Save and Exit
Figure 15. Boot Menu
Table 15: Fields, Options and Defaults for the Boot Menu
Menu Field
Options
Default
Description
QuickBoot:
■
Disabled
Enabled
[Enabled]
Turns on and off booting with a truncated set of Power On Self Test.
(Fewer tests mean faster booting.)
Disabled
Enabled
[Disabled]
Turns on and off display of test results instead of Fujitsu logo screen
during Power On Self Test.
Disabled
Enabled
[Enabled]
This field is not active unless the Supervisor’s Password has
been set. When disabled, access to the Boot Menu with the
[F12] key is disabled. When enabled, the Boot Menu is enabled
and the [F12] key will allow you to display it.
Disabled
Enabled
[Enabled]
Turns on and off the preboot execution environment feature.
—
This menu allows setting up the source for the operating system.
See “The Boot Device Priority Submenu” in the following section.
■
Boot-time
Diagnostic Screen:
■
Boot Menu:
■
■
■
Preboot Execution
Environment:
■
Boot Device
Priority
—
■
23
LifeBook V Series Notebook BIOS
Boot Device Priority Submenu of the Boot Menu
The Boot Device Priority Submenu is for setting the order of checking of sources for the operating system.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Boot
Boot Device Priority
Item Specific Help
Boot priority order:
1: Floppy Disk Drive
2. Drive0: FUJITSU MHV2080BH
3. CD/DVD Drive
4. NETWORK: MBA vXX.X.XX Slot 0400
5:
6.
7:
8:
Excluded from boot order:
: USB MEMORY: None
: USB HDD: None
Select Item
Select Menu
<+>/<Space> or <->
moves the device up or
down.
<x> excludes or includes
the device to boot.
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Keys used to view or
configure devices:
F9 Setup Defaults
F10 Save and Exit
Figure 16. Boot Device Priority Submenu
■
■
Be aware of the operating environment when booting from a CD-ROM/DVD-ROM or you may overwrite files by mistake.
A bootable CD-ROM/DVD-ROM has either a floppy disk format or a hard drive format. When the bootable CD-ROM/DVD-ROM is used, the drive allocations change automatically without changing the BIOS
setup. If a floppy disk format is used, the CD-ROM/DVD-ROM becomes Drive A. The CD-ROM/DVDROM will only take drive C: (hard drive format) if the internal hard drive is not present or is disabled. The
bootable CD-ROM/DVD-ROM can never use a C: designation if a formatted internal hard drive is
present since the C: designator is always reserved for the internal hard drive. The boot sequence ignores
the new drive designations, however, your application software will use the new designations.
Table 16: Fields, Options and Defaults for the Boot Device Priority Submenu of the Boot Menu
24
Menu Field
Description
1; Floppy Disk Drive
2: Drive0
3: CD/DVD Drive
4: NETWORK
5:
6:
7:
8:
Excluded from boot
order:
: USB MEMORY: None
: USB HDD: None
The boot selections determine the order in which the BIOS searches for the operating system during a
startup sequence. To change the order, highlight one source by using the [up] or [down] cursor keys and
then press the [+] or [-] key to change the order number. The selections that appear above may be different
for your system, depending upon configuration.
NOTE: Be aware that if you use the CD-ROM drive as the first boot device, certain files may be
overwritten, depending upon your operating environment.
Boot Menu
Exiting from Boot Menu
When you have finished setting the boot parameters with the Boot menu, you can either exit from the setup utility or
move to another menu. If you wish to exit from the setup utility press the Esc key to go to the Exit menu. If you wish to
move to another menu, use the cursor keys.
25
LifeBook V Series Notebook BIOS
INFO MENU - DISPLAYS BASIC SYSTEM INFORMATION
The Info menu is a display only screens that provides the
configuration information for your notebook.
The information, including CPU type and
speed, and total memory, displayed on this
screen varies according to the unit you
purchased.
The following table shows the names of the menu fields
for the Info menu and the information displayed in
those fields. These fields are for information purposes
only, and cannot be modified by the user.
Main
Advanced
PhoenixBIOS Setup Utility
Security
Power Savings
Boot
BIOS Version:
BIOS Date:
BIOS Area:
1.05
09/06/2007
E000h - FFFFh
CPU Type:
CPU Speed:
L1 Cache:
L2 Cache:
Intel(R) Core(TM)2 CPU T5500
1.66 GHz
128 KB
2048 KB
Info
Total Memory:
1024 MB
Memory Slot 1: 512 MB DDR2 SDRAM
Memory Slot 2: 512 MB DDR2 SDRAM
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
F9
F10
Setup Defaults
Save and Exit
Figure 17. Info Menu
Table 17: Fields, Options and Defaults for the Info Menu
Note that the parameters listed in the following table may be different, depending upon the system configuration.
Menu Field
Default
Menu Field
Default
BIOS Version:
X.XX
L1 Cache:
128 KB
BIOS Date:
XX/XX/XXXX
L2 Cache:
2048 KB
BIOS Area:
E000h – FFFFh
Total Memory:
1024 MB
CPU Type:
Genuine Intel(R) Core(TM)2 CPU T5500
Memory Slot 1:
512 MB DDR2 SDRAM
CPU Speed:
1.66 GHz
Memory Slot 2:
512 MB DDR2 SDRAM
26
Exit Menu
EXIT MENU – LEAVING THE SETUP UTILITY
The Exit Menu is used to leave the setup utility. Follow
the instructions for Navigating Through the Setup
Utility to make any changes. (See Navigating through the
Setup Utility on page 2 for more information.)
Main
Advanced
The following table shows the names of the menu fields
for the Exit menu, the default settings and a description
of the field's function and any special information
needed to help understand the field's use.
PhoenixBIOS Setup Utility
Security
Power Savings
Boot
Exit
Item Specific Help
Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
Save Changes and Power Off
Select Item
Select Menu
-/Space Change Values
Enter
Select Sub-Menu
▲
F1 Help
ESC Exit
Exit System Setup and
save your changes to
CMOS.
F9
F10
Setup Defaults
Save and Exit
Figure 18. Exit Menu
Table 18: Fields, Options and Defaults for the Exit Menu
Menu Field
Description
Exit Saving
Changes
Exit Saving Changes will store the entries on all setup utility menus to the BIOS memory and then
exit the setup utility. A confirmation message Save Configuration changes and exit now? [Yes] [No]
will be displayed.
Exit Discarding
Changes
Selecting Exit Discarding Changes will exit the setup utility with out writing to the BIOS memory.
When the BIOS recognizes this selection it will load the operating system and begin operation.
Load Setup
Defaults
Selecting Load Setup Defaults will load the factory preset default values for all menu fields, then display the message Load default configuration now? [Yes] [No]. When confirmed the setup utility will
return to the Exit Menu. To return to another menu follow the directions in the Navigating Through
the Setup Utility Section.
27
LifeBook V Series Notebook BIOS
Table 18: Fields, Options and Defaults for the Exit Menu
Menu Field
Description
Discard Changes
Selecting Discard Changes will load the previous values in BIOS memory for all menu fields. The
message Load previous now? [Yes] [No] will be displayed. When confirmed the setup utility will
return to the Exit menu. To return to another menu, follow the directions in the Navigating Through
the Setup Utility Section.
Save Changes
Selecting Save Changes will cause the new settings in all menus to be written to the BIOS memory.
The message Save configuration changes now? [Yes] [No] will be displayed. When confirmed, the
setup utility will return to the Exit menu. To return to another menu, follow the directions in the
Navigating Through the Setup Utility section.
Save Changes
and Power Off
Selecting Save Changes and Power Off will cause the new settings in all menus to be written to the
BIOS memory, after which the system will power itself off. The message Save configuration changes
and power off now? [Yes] [No] will be displayed. When confirmed, the setup utility save the settings
and the system will power off.
28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement