ConRoeXFire-eSATA2 User Manual 11 1
ConRoeXFire-eSATA2
User Manual
Version 2.3
Published January 2007
Copyright©2007 ASRock INC. All rights reserved.
1
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in
any language, in any form or by any means, except duplication of documentation by
the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed
as a commitment by ASRock. ASRock assumes no responsibility for any errors or
omissions that may appear in this manual.
With respect to the contents of this manual, ASRock does not provide warranty of
any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the manual or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic
substance controlled in Perchlorate Best Management Practices (BMP) regulations
passed by the California Legislature. When you discard the Lithium battery in
California, USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com
2
Contents
1 Introduction ................................................... 5
1.1 Package Contents .......................................................... 5
1.2 Specifications ................................................................ 6
1.3 Minimum Hardware Requirement Table for Windows®
VistaTM Premium and Basic Logo.................................. 9
1.4 Supported PCI Express VGA Card List for AGI Express
Slot (PCI Express x4) .................................................... 10
1.5 Motherboard Layout ...................................................... 11
1.6 ASRock 8CH_eSATAII I/O .............................................. 12
2 Installation ...................................................... 13
2.1 Screw Holes ................................................................. 13
2.2 Pre-installation Precautions ........................................... 13
2.3 CPU Installation .............................................................. 14
2.4 Installation of Heatsink and CPU fan ............................. 16
2.5 Installation of Memory Modules (DIMM) ......................... 17
2.6 Expansion Slots ............................................................. 19
2.7 CrossFireTM Operation Guide ......................................... 20
2.8 Surround Display Feature ............................................. 24
2.9 Jumpers Setup .............................................................. 24
2.10 Onboard Headers and Connectors .............................. 24
2.11 HDMI_SPDIF Header Connection Guide ......................... 30
2.12 eSATAII Interface Introduction ....................................... 31
2.13 SATAII Hard Disk Setup Guide ....................................... 34
2.14 Serial ATA (SATA) / Serial ATAII (SATAII) Hard Disks
Installation ...................................................................... 35
2.15 Hot Plug and Hot Swap Functions for SATA / SATAII ...
HDDs and eSATAII Devices ........................................... 36
2.16 Driver Installation Guide ............................................... 36
2.17 Installing Windows® 2000 / XP / XP 64-bit / VistaTM /
VistaTM 64-bit With RAID Functions ............................... 36
2.17.1 Installing Windows® 2000 / XP / XP 64-bit With
RAID Functions .................................................. 37
2.17.2 Setting Up a RAID Ready System ...................... 38
2.17.3 Migrating a “RAID Ready” System to RAID 0,
RAID 1 or RAID 5 ................................................ 39
2.17.4 Installing Windows® VistaTM / VistaTM 64-bit With
RAID Functions .................................................. 39
3
2.18 Installing Windows® 2000 / XP / XP 64-bit / VistaTM /
VistaTM 64-bit Without RAID Functions ..........................
2.18.1 Installing Windows® 2000 / XP / XP 64-bit
Without RAID Functions .....................................
2.18.2 Installing Windows® VistaTM / VistaTM 64-bit
Without RAID Functions .....................................
2.19 Untied Overclocking Technology ...................................
40
40
41
42
3 BIOS SSETUP
ETUP UTILITY ........................................... 43
3.1 Introduction ....................................................................
3.1.1 BIOS Menu Bar ....................................................
3.1.2 Navigation Keys ...................................................
3.2 Main Screen ...................................................................
3.3 Advanced Screen .........................................................
3.3.1 CPU Configuration ................................................
3.3.2 Chipset Configuration ..........................................
3.3.3 ACPI Configuration ...............................................
3.3.4 IDE Configuration .................................................
3.3.5 PCIPnP Configuration ...........................................
3.3.6 Floppy Configuration ...........................................
3.3.7 Super IO Configuration ........................................
3.3.8 USB Configuration ...............................................
3.4 Hardware Health Event Monitoring Screen ..................
3.5 Boot Screen ...................................................................
3.5.1 Boot Settings Configuration ..................................
3.6 Security Screen ............................................................
3.7 Exit Screen ....................................................................
43
43
44
44
44
45
47
49
50
52
53
53
55
55
56
57
57
58
4 Software Support ........................................... 59
4.1 Install Operating System ...............................................
4.2 Support CD Information .................................................
4.2.1 Running Support CD ............................................
4.2.2 Drivers Menu ........................................................
4.2.3 Utilities Menu ........................................................
4.2.4 “LGA 775 CPU Installation Live Demo” Program ..
4.2.5 Contact Information ..............................................
4
59
59
59
59
59
59
59
Chapter 1 Introduction
Thank you for purchasing ASRock ConRoeXFire-eSATA2 motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-bystep guide to the hardware installation. Chapter 3 and 4 contain the configuration
guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be
updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest VGA cards and CPU support lists on ASRock website
as well. ASRock website http://www.asrock.com
1.1 Package Contents
ASRock ConRoeXFire-eSATA2 Motherboard
(ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm)
ASRock ConRoeXFire-eSATA2 Quick Installation Guide
ASRock ConRoeXFire-eSATA2 Support CD
(including LGA 775 CPU Installation Live Demo)
One 80-conductor Ultra ATA 66/100 IDE Ribbon Cable
One Ribbon Cable for a 3.5-in Floppy Drive
Four Serial ATA (SATA) Data Cables (Optional)
Two Serial ATA (SATA) HDD Power Cables (Optional)
One HDMI_SPDIF Cable (Optional)
One ASRock 8CH_eSATAII I/O Panel Shield
One USB+1394 Bracket
5
1.2
Specifications
Platform
CPU
Chipset
Memory
Hybrid Booster
Expansion Slot
Audio
LAN
Rear Panel I/O
Connector
- ATX Form Factor: 12.0-in x 8.6-in, 30.5 cm x 21.8 cm
- LGA 775 for Intel® Dual Core CoreTM 2 Extreme / CoreTM 2 Duo
/ Pentium® D / Pentium® 4 / Celeron® D processors
- FSB 1066/800/533 MHz
- Supports Hyper-Threading Technology (see CAUTION 1)
- Supports Untied Overclocking Technology (see CAUTION 2)
- Supports EM64T CPU
- Northbridge: Intel® 945P/945G
- Southbridge: Intel® ICH7R
- Dual Channel DDRII Memory Technology (see CAUTION 3)
- 4 x DDRII DIMM slots
- Support DDRII667/533 (see CAUTION 4)
- Max. capacity: 4GB (see CAUTION 5)
- CPU Frequency Stepless Control (see CAUTION 6)
- ASRock U-COP (see CAUTION 7)
- Boot Failure Guard (B.F.G.)
- Supports ATITM CrossFireTM
- 3 x PCI slots
- 1 x PCI Express x16 slot
- 1 x AGI Express slot (PCI Express x4) (see CAUTION 8)
- 1 x PCI Express x1 slot
- 7.1 CH Windows® VistaTM Premium Level HD Audio
(ALC888 Audio Codec)
- PCIE x1 Gigabit LAN 10/100/1000 Mb/s
- Realtek RTL8111B
- Supports Wake-On-LAN
ASRock 8CH_eSATAII I/O
- 1 x PS/2 Mouse Port
- 1 x PS/2 Keyboard Port
- 1 x Serial Port: COM1
- 1 x Parallel Port (ECP/EPP Support)
- 2 x Ready-to-Use USB 2.0 Ports
- 2 x eSATAII Ports
- 1 x RJ-45 Port
- HD Audio Jack: Side Speaker/Rear Speaker/Central/Bass/
Line in/Front Speaker/Microphone (see CAUTION 9)
- 4 x SATAII 3.0Gb/s connectors, support RAID (RAID 0,
RAID 1, RAID 10, RAID 5 and Intel Matrix Storage), NCQ,
AHCI and “Hot Plug” functions (see CAUTION 10)
6
BIOS Feature
Support CD
Hardware
Monitor
OS
Certifications
- 2 x eSATAII 3.0Gb/s connectors (shared with 2 SATAII
connectors), support “Hot Plug” function (see CAUTION 11)
- 1 x ATA100 IDE connector (supports 2 x IDE devices)
- 1 x Floppy connector
- 1 x IR header
- 1 x Game header
- 1 x HDMI_SPDIF header
- 2 x IEEE 1394 headers
- CPU/Chassis FAN connector
- 20 pin ATX power connector
- 4 pin 12V power connector
- SLI/XFIRE power connector
- CD in header
- Front panel audio connector
- 3 x USB 2.0 headers (support 6 USB 2.0 ports)
(see CAUTION 12)
- 4Mb AMI BIOS
- AMI Legal BIOS
- Supports “Plug and Play”
- ACPI 1.1 Compliance Wake Up Events
- Supports jumperfree
- AMBIOS 2.3.1 Support
- Drivers, Utilities, AntiVirus Software (Trial Version)
- CPU Temperature Sensing
- Chassis Temperature Sensing
- CPU Fan Tachometer
- Chassis Fan Tachometer
- CPU Quiet Fan
- Voltage Monitoring: +12V, +5V, +3.3V, CPU Vcore
- Microsoft® Windows® 2000/XP/XP 64-bit/VistaTM/
VistaTM 64-bit compliant (see CAUTION 13)
- FCC, CE, WHQL
WARNING
Please realize that there is a certain risk involved with overclocking, including adjusting
the setting in the BIOS, applying Untied Overclocking Technology, or using the thirdparty overclocking tools. Overclocking may affect your system stability, or even
cause damage to the components and devices of your system. It should be done at
your own risk and expense. We are not responsible for possible damage caused by
overclocking.
7
CAUTION!
1.
2.
About the setting of “Hyper Threading Technology”, please check page 46.
This motherboard supports Untied Overclocking Technology. Please read
3.
“Untied Overclocking Technology” on page 42 for details.
This motherboard supports Dual Channel Memory Technology. Before you
implement Dual Channel Memory Technology, make sure to read the
installation guide of memory modules on page 17 for proper installation.
4.
Please check the table below for the CPU FSB frequency and its
corresponding memory support frequency.
CPU FSB Frequency
1066
800
533
5.
Memory Support Frequency
DDRII533, DDRII667
DDRII400, DDRII533, DDRII667
DDRII400, DDRII533
Due to the chipset limitation, the actual memory size may be less than
4GB for the reservation for system usage under Windows® 2000, Windows® XP, Windows® XP 64-bit, Windows® VistaTM and Windows® VistaTM
64-bit.
6.
Although this motherboard offers stepless control, it is not recommended
to perform over-clocking. Frequencies other than the recommended CPU
bus frequencies may cause the instability of the system or damage the
CPU.
7.
While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the
motherboard functions properly and unplug the power cord, then plug it
back again. To improve heat dissipation, remember to spray thermal
8.
grease between the CPU and the heatsink when you install the PC system.
For the information of the compatible PCI Express VGA cards, please
refer to the “Supported PCI Express VGA Card List for AGI Express Slot
(PCI Express x4)” on page 10. For the proper installation of PCI Express
9.
VGA card, please refer to the installation guide on page 19.
For microphone input, this motherboard supports both stereo and mono
modes. For audio output, this motherboard supports 2-channel, 4-channel,
6-channel, and 8-channel modes. Please check the table on page 12 for
proper connection.
10. Before installing SATAII hard disk to SATAII connector, please read the
“SATAII Hard Disk Setup Guide” on page 34 to adjust your SATAII hard disk
drive to SATAII mode. You can also connect SATA hard disk to SATAII
connector directly.
11. This motherboard supports eSATAII interface, the external SATAII
specification. Please read “eSATAII Interface Introduction” on page 31 for
details about eSATAII and eSATAII installation procedures. (Port Multiplier
Technology is not supported with eSATAII interface on this motherboard.)
12. Power Management for USB 2.0 works fine under Microsoft® Windows®
VistaTM 64-bit / VistaTM / XP 64-bit / XP SP1 or SP2 / 2000 SP4.
8
13. Microsoft® Windows® VistaTM / VistaTM 64-bit driver keeps on updating now. As
long as we have the latest driver, we will update it to our website in the future.
Please visit our website for Microsoft® Windows® VistaTM / VistaTM 64-bit driver
and related information.
ASRock website http://www.asrock.com
1.3
Minimum Hardware R
equirement TTable
able for W
indows ®
Requirement
Windows
TM
Vista Premium and Basic Logo
For system integrators and users who purchase this motherboard and
plan to submit Windows® VistaTM Premium and Basic logo, please follow the
below table for minimum hardware requirement.
CPU
Memory
Celeron D 326
512MB Single Channel
VGA
DX9.0 with WDDM Driver
with 128bit VGA memory (Premium)
with 64bit VGA memory (Basic)
9
1.4
Supported PCI Express VGA Card List for AGI
Express Slot (PCI Express x4)
(for Windows® 2000/XP/XP 64-bit/VistaTM/VistaTM 64-bit)
Graphics Chip
Vendor
NVIDIA
Model Name
Chipset Name
ASUS EN5750
ASUS EN6600
GeForce PCX5750
GeForce 6600
ASUS EN6600GT Series
ASUS EN7600GT/2DHT
GeForce 6600GT
GeForce 7600GT
ASUS EN7900GT/2DHT/256M
GeForce 7900 GT
ASUS Extreme 7800GTX/2DHTV/256M GeForce 7800 GTX
ATI
ASUS Extreme N6200GE/TD
ASUS Extreme N6200TC256/TD
GeForce 6200
GeForce 6200
ASUS Extreme N6800/TD
ASUS Extreme N6800GT
GeForce 6800
GeForce 6800GT
Albatron PC6600GT
Gigabyte GV-NX66128D
GeForce 6600GT
GeForce 6600
Inno3D GeFORCE 6600 LE
Leadtek PX6200 TC/TDH
GeForce 6600LE
GeForce 6200TC
LEADTEK PX6500 TDH
LEADTEK PX7300GS TDH
GeForce 6500
GeForce 7300GS
LEADTEK WinFast PX7800 GT TDH
LEADTEK WinFast PX7800 GTX TDH
GeForce 7800 GT
GeForce 7800 GTX
MSI NX6800GS-TD256E
MSI NX7300GS-TD256E
GeForce 6800 GS
GeForce 7300 GS
MSI NX7900GTX-T2D512E
MSI PCX 5750-TD128E
GeForce 7900 GTX
GeForce PCX5750
Sparkle GeFORCE 6200TC
ASUS EAX600XT/HTVD
GeForce 6200TC
Radeon X600XT
ASUS EAX700PRO/TVD
ASUS EAX700PRO/TVD/256M R1.00
Radeon X700 Pro
Radeon X700 Pro
Gecube Radeon X850XT 256M
Gecube RX1300PG2-D3/256M
Radeon X850XT
RADEON X1300PRO
GECUBE RX1600PG2
Gecube RX1600XTG3-D3/256M
Radeon X1600PRO
Radeon X1600XT
GECUBE X1800XTD-VIE3
MSI RX1300GPRO-TD256E
Radeon X1800XT
Radeon X1300 PRO
MSI RX1600XT-T20256EZ
Radeon X1600XT
For the latest updates of the supported PCI Express VGA card list for AGI Express
slot (PCI Express x4), please visit our website for details.
ASRock website: http://www.asrock.com/support/index.htm
10
1.5 Motherboard Layout
1
3
2
5
4
8
7
6
21.8cm (8.6 in)
1
PS2_USB_PWR1
PCIE1
ConRoeXFire-eSATA2
PCIE2
IDE1
EXPRESS
33
CMOS
Battery
AGI_EXPRESS1
7.1CH HD
BACK_1394
31
1
30
HDMI_SPDIF1
PCI 2
9
10
11
12
13
14
15
16
17
18
SATAII_RED SATAII_ORANGE
(PORT3)
(PORT2)
1
PCI 3
AUDIO
CODEC
HD_AUDIO1
CD1
8
USB2.0 RoHS
1394a
GAME1
FRONT_1394
1
27
SATAII_BLUE SATAII_BLACK
(PORT1)
(PORT0)
USB23
SPEAKER1 1
1
FLOPPY1
1
1
28
1
2
3
4
5
6
7
Intel
ICH7R
1
4Mb
BIOS
SATAII
CLRCMOS1
PCI 1
32
9
10
RAID
PCI
Super
I/O
30.5cm (12.0 in)
Gigabit LAN
Presler Conroe
Dual Core CPU
`
34
29
DDR_II DIMM4 (64/72 bit, 240-pin module)
Center:
FRONT
Top:
LINE IN
DDR_II DIMM2 (64/72 bit, 240-pin module)
Bottom:
MIC IN
LAN
PHY
Intel
945P/945G
Chipset
DDR_II DIMM3 (64/72 bit, 240-pin module)
Center:
SIDE SPK
35
FSB1066
SLI/XFIRE_PWR1
Bottom:
CTR BASS
Top:
REAR SPK
eSATAII
USB 2.0
T: USB0 Top:
RJ-45
B: USB1
ATXPWR1
eSATAII_12
T: eSATAII_1
B: eSATAII_2
36
DDRII667
Dual Channel
eSATAII_TOP
eSATAII_BOTTOM
COM1
PARALLEL PORT
PS2
Keyboard
37
CPU_FAN1
ATX12V1
DDR_II DIMM1 (64/72 bit, 240-pin module)
PS2
Mouse
1
IR1
USB67
USB45
1
1
PANEL1
CHA_FAN1
PLED PWRBTN
1
HDLED
11
12
13
14
15
16
17
RESET
25 24 2322 21 20 19 18
26
PS2_USB_PWR1 Jumper
ATX 12V Connector (ATX12V1)
SLI / XFIRE Power Connector
775-Pin CPU Socket
North Bridge Controller
CPU Fan Connector (CPU_FAN1)
2 x 240-pin DDRII DIMM Slots
(Dual Channel A: DDRII_1, DDRII_3; Yellow)
2 x 240-pin DDRII DIMM Slots
(Dual Channel B: DDRII_2, DDRII_4; Orange)
PCI Express x16 Slot (PCIE1)
IDE1 Connector (IDE1, Blue)
Clear CMOS Jumper (CLRCMOS1)
BIOS FWH Chip
Serial ATAII Connector (SATAII_RED (PORT2))
Serial ATAII Connector (SATAII_ORANGE (PORT3))
Serial ATAII Connector (SATAII_BLACK (PORT1))
Serial ATAII Connector (SATAII_BLUE (PORT0))
Chassis Fan Connector (CHA_FAN1)
System Panel Header (PANEL1)
11
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Chassis Speaker Header (SPEAKER 1)
Infrared Module Connector (IR1)
USB 2.0 Header (USB67, Blue)
South Bridge Controller
USB 2.0 Header (USB45, Blue)
USB 2.0 Header (USB23, Blue)
Front Panel IEEE 1394 Header (FRONT_1394)
Floppy Connector (FLOPPY1)
Game Port Header (GAME1)
Internal Audio Connector: CD1 (Black)
Front Panel Audio Header (HD_AUDIO1)
HDMI_SPDIF Header (HDMI_SPDIF1)
Back Panel IEEE 1394 Header (BACK_1394)
PCI Slots (PCI1- 3)
AGI Express Slot (PCI Express x4)
PCI Express x1 Slot (PCIE2)
ATX Power Connector (ATXPWR1)
eSATAII Connector (eSATAII_BOTTOM)
eSATAII Connector (eSATAII_TOP)
1.6
ASR
ock 8CH_eSA
ASRock
8CH_eSATTAII I/O
2
1
12
13
1
2
3
4
5
6
*7
11
8
9
10
11
12
13
6
4
7
5
8
9
10
Parallel Port
RJ-45 Port
Side Speaker (Gray)
Rear Speaker (Black)
Central / Bass (Orange)
Line In (Light Blue)
3
Microphone (Pink)
USB 2.0 Ports (USB01)
eSATAII Ports
COM Port
PS/2 Keyboard Port (Purple)
PS/2 Mouse Port (Green)
Front Speaker (Lime)
* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See
the table below for connection details in accordance with the type of speaker you use.
TABLE for Audio Output Connection
Audio Output Channels Front Speaker Rear Speaker
(No. 7)
(No. 4)
Central / Bass
(No. 5)
Side Speaker
(No. 3)
2
4
V
V
-V
---
---
6
8
V
V
V
V
V
V
-V
* To enable Multi-Streaming function, you need to connect a front panel audio cable to the front
panel audio header. After restarting your computer, you will find “Mixer” tool on your system.
Please select “Mixer ToolBox”
, click “Enable playback multi-streaming”, and click
“ok”. Choose “2CH”, “4CH”, “6CH”, or “8CH” and then you are allowed to select “Realtek HDA
Primary output” to use Rear Speaker, Central/Bass, and Front Speaker, or select “Realtek HDA
Audio 2nd output” to use front panel audio.
12
Chapter 2 Installation
ConRoeXFire-eSATA2 is an ATX form factor (12.0" x 8.6", 30.5 x 21.8 cm)
motherboard. Before you install the motherboard, study the configuration of your
chassis to ensure that the motherboard fits into it.
Make sure to unplug the power cord before installing or removing the
motherboard. Failure to do so may cause physical injuries to you and
damages to motherboard components.
2.1 Screw Holes
Place screws into the holes indicated by circles to secure the motherboard to the
chassis.
Do not over-tighten the screws! Doing so may damage the motherboard.
2.2 Pre-installation Precautions
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any component.
2. To avoid damaging the motherboard components due to static electricity, NEVER
place your motherboard directly on the carpet or the like. Also remember to use
a grounded wrist strap or touch a safety grounded object before you handle
components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded antistatic pad or
in the bag that comes with the component.
Before you install or remove any component, ensure that the power is
switched off or the power cord is detached from the power supply.
Failure to do so may cause severe damage to the motherboard, peripherals,
and/or components.
13
2.3 CPU Installation
For the installation of Intel 775-LAND CPU,
please follow the steps below.
775-Pin Socket Overview
Before you insert the 775-LAND CPU into the socket, please check if
the CPU surface is unclean or if there is any bent pin on the socket.
Do not force to insert the CPU into the socket if above situation is
found. Otherwise, the CPU will be seriously damaged.
Step 1. Open the socket:
Step 1-1. Disengaging the lever by depressing
down and out on the hook to clear
retention tab.
Step 1-2. Rotate the load lever to fully open position at approximately 135 degrees.
Step 1-3. Rotate the load plate to fully open position at approximately 100 degrees.
black line
black line
Step 2. Insert the 775-LAND CPU:
Step 2-1. Hold the CPU by the edges where are
marked with black lines.
Step 2-2. Orient the CPU with IHS (Integrated
Heat Sink) up. Locate Pin1 and the two
orientation key notches.
Pin1
orientation
key notch
Pin1
alignment key
orientation
key notch
alignment key
775-Pin Socket
775-LAND CPU
14
For proper inserting, please ensure to match the two orientation key
notches of the CPU with the two alignment keys of the socket.
Step 2-3. Carefully place the CPU into the socket
by using a purely vertical motion.
Step 2-4. Verify that the CPU is within the socket
and properly mated to the orient keys.
Step 3. Remove PnP Cap (Pick and Place Cap):
Use your left hand index finger and thumb to
support the load plate edge, engage PnP cap
with right hand thumb and peel the cap from the
socket while pressing on center of PnP cap to
assist in removal.
1. It is recommended to use the cap tab to handle and avoid kicking
off the PnP cap.
2. This cap must be placed if returning the motherboard for after
service.
Step 4. Close the socket:
Step 4-1. Rotate the load plate onto the IHS.
Step 4-2. While pressing down lightly on load
plate, engage the load lever.
Step 4-3. Secure load lever with load plate tab
under retention tab of load lever.
15
2.4
Installation of CPU Fan and Heatsink
This motherboard is equipped with 775-Pin socket that supports Intel 775-LAND CPU.
Please adopt the type of heatsink and cooling fan compliant with Intel 775-LAND CPU
to dissipate heat. Before you installed the heatsink, you need to spray thermal
interface material between the CPU and the heatsink to improve heat dissipation.
Ensure that the CPU and the heatsink are securely fastened and in good contact with
each other. Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1, see
page 11, No. 6).
For proper installation, please kindly refer to the instruction manuals of
your CPU fan and heatsink.
Below is an example to illustrate the installation of the heatsink for 775-LAND CPU.
Step 1. Apply thermal interface material onto center
of IHS on the socket surface.
Step 2.
Step 3.
Step 4.
Place the heatsink onto the socket. Ensure
fan cables are oriented on side closest to the
CPU fan connector on the motherboard
(CPU_FAN1, see page 11, No. 6).
Align fasteners with the motherboard
throughholes.
Rotate the fastener clockwise, then press
down on fastener caps with thumb to install
and lock. Repeat with remaining fasteners.
If you press down the fasteners without rotating them clockwise,
the heatsink cannot be secured on the motherboard.
Step 5.
Step 6.
Connect fan header with the CPU fan
connector on the motherboard.
Secure excess cable with tie-wrap to ensure
cable does not interfere with fan operation or
contact other components.
16
2.5 Installation of Memory Modules (DIMM)
ConRoeXFire-eSATA2 motherboard provides four 240-pin DDRII (Double Data
Rate II) DIMM slots, and supports Dual Channel Memory Technology. For dual
channel configuration, you always need to install identical (the same brand,
speed, size and chip-type) DDRII DIMM pair in the slots of the same color. In other
words, you have to install identical DDRII DIMM pair in Dual Channel A (DDRII_1
and DDRII_3; Yellow slots; see p.11 No.7) or identical DDRII DIMM pair in Dual
Channel B (DDRII_2 and DDRII_4; Orange slots; see p.11 No.8), so that Dual
Channel Memory Technology can be activated. This motherboard also allows
you to install four DDRII DIMMs for dual channel configuration, and please install
identical DDRII DIMMs in all four slots. You may refer to the Dual Channel
Memory Configuration Table below.
Dual Channel Memory Configurations
DDRII_1
(Yellow Slot)
Populated
Populated
(1)
(2)
(3)*
DDRII_2
DDRII_3
(Orange Slot) (Yellow Slot)
Populated
Populated
Populated
Populated
DDRII_4
(Orange Slot)
Populated
Populated
* For the configuration (3), please install identical DDRII DIMMs in all four slots.
1.
If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them in the slots of the
same color. In other words, install them either in the set of yellow
slots (DDRII_1 and DDRII_3), or in the set of orange slots (DDRII_2
and DDRII_4).
2.
3.
If only one memory module or three memory modules are installed
in the DDRII DIMM slots on this motherboard, it is unable to activate
the Dual Channel Memory Technology.
If a pair of memory modules is NOT installed in the same Dual
Channel, for example, installing a pair of memory modules in DDRII_1
and DDRII_2, it is unable to activate the Dual Channel Memory
4.
Technology .
It is not allowed to install a DDR memory module into DDRII slot;
5.
otherwise, this motherboard and DIMM may be damaged.
If you plan to use ATITM PCI Express VGA card on this motherboard,
the total system memory size should be above 512MB.
17
Installing a DIMM
Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.
Step 1.
Step 2.
Unlock a DIMM slot by pressing the retaining clips outward.
Align a DIMM on the slot such that the notch on the DIMM matches the break
on the slot.
notch
break
notch
break
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into the
slot at incorrect orientation.
Step 3.
Firmly insert the DIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.
18
2.6 Expansion Slots (PCI, PCI Express, and AGI Express
Slots)
There are 3 PCI slots, 2 PCI Express slots, and 1 AGI Express slot (PCI Express x4)
on this motherboard.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
PCIE Slots: PCIE1 (PCIE x16 slot) is used for PCI Express cards with x16 lane
width graphics cards.
PCIE2 (PCIE x1 slot) is used for PCI Express cards with x1 lane
width cards, such as Gigabit LAN card, SATA2 card, etc.
AGI Express slot (PCI Express x4):
AGI Express slot (PCI Express x4) is used to install PCI Express expansion cards. For the information of the compatible PCI Express VGA cards,
please refer to the “Supported PCI Express VGA Card List for AGI Express Slot (PCI Express x4)” on page 10.
Installing an expansion card
Step 1.
Step 2.
Step 3.
Step 4.
Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Remove the bracket facing the slot that you intend to use. Keep the screws
for later use.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Fasten the card to the chassis with screws.
19
2.7 CrossFire TM Operation Guide
This motherboard supports CrossFireTM feature. CrossFireTM technology offers the
most advantageous means available of combining multiple high performance
Graphics Processing Units (GPU) in a single PC. Combining a range of different
operating modes with intelligent software design and an innovative interconnect
mechanism, CrossFireTM enables the highest possible level of performance and
image quality in any 3D application. Currently CrossFireTM feature is only supported
with Windows® XP with Service Pack 2; it may be supported with other OS in the
future, such as Windows® VistaTM. Please check ATITM website for driver updates.
What graphics cards work with CrossFire TM?
A complete CrossFireTM system requires a CrossFireTM Ready motherboard, a
CrossFireTM Edition graphics card and a compatible standard Radeon (CrossFireTM
Ready) graphics card from the same series, or two CrossFireTM Ready cards if they
are software enabled. This applies to cards from ATITM or any of its partners.
Cards For AGI Express Slot
Cards For PCIE1 Slot
Radeon X1950Pro Series
Radeon X1950XTX Series
Radeon X1950Pro Series
Radeon X1950XTX CrossFireTM Edition
Radeon X1950 Series
Radeon X1900 Series
Radeon X1950 CrossFireTM Edition
Radeon X1900 CrossFireTM Edition
Radeon X1800 Series
Radeon X1650Pro Series
Radeon X1800 CrossFireTM Edition
Radeon X1650Pro Series
Radeon X1600 Series
Radeon X1300 Series
Radeon X1600 Series
Radeon X1300 Series
Radeon X850 Series
Radeon X850 CrossFireTM Edition
1. If a customer incorrectly configures their system they will not see the
performance benefits of CrossFireTM. All three CrossFireTM components, a
CrossFireTM Ready graphics card, a CrossFireTM Ready motherboard and a
CrossFireTM Edition co-processor graphics card, must be installed correctly to
benefit from the CrossFireTM multi-GPU platform.
2. If you pair a 12-pipe CrossFireTM Edition card with a 16-pipe card, both cards will
operate as 12-pipe cards while in CrossFireTM mode.
Enjoy the benefit of CrossFire TM
Currently, ATITM has released Radeon X850XT, X1800XT, X1900XT, X1950XT, X1950Pro,
X1950XTX, X1300, X1650 and X1600 CrossFireTM cards, which require different
methods to enable CrossFireTM feature. In the below procedures, we use Radeon
X850XT as the example graphics card. For other CrossFireTM cards that ATITM has
released or will release in the future, please refer to ATITM graphics card manuals for
detailed installation guide.
Step 1.
Connect to the system power supply. Please connect a hard disk power
connector to SLI/XFIRE Power connector on this motherboard.
It is recommended to use 500-Watt power supply or greater
to perform the benefit of CrossFire TM feature for Radeon
X850XT, X1900 and X1950 series.
20
Step 2.
Install the standard Radeon (CrossFireTM Ready) graphics card to AGI Express slot (PCI Express x4). For the proper installation procedures, please
refer to section “Expansion Slots”.
Standard Radeon
(CrossFireTM Ready)
graphics card
Step 3.
Install the Radeon CrossFireTM Edition graphics card to PCIE1 slot. For the
proper installation procedures, please refer to section “Expansion Slots”.
Radeon CrossFireTM
Edition graphics card
Standard Radeon
(CrossFireTM Ready)
graphics card
1. You are allowed to install two CrossFireTM Edition graphics cards to both slots, or you
may use one CrossFireTM Edition graphics cards and a compatible standard Radeon
(CrossFireTM Ready) graphics card from the same series.
2. For ATITM Radeon X1300, X1600, X1650 and X1950Pro series, there are no CrossFireTM
Edition graphics cards. You can still install two regular graphics cards from the same
series on PCIE1 slot and AGI Express slot (PCI Express x4) to support CrossFireTM.
Besides, please connect the monitor cable to the graphics card on PCIE1 slot.
Step 4.
Correctly connect the DVI-DMS cable to the monitor connector and two
graphics cards that you install. (If you install two standard Radeon
(CrossFireTM Ready) graphics cards to this motherboard, please skip this
step.)
DVI-DMS cable
DMS connector
DVI connector
Standard Radeon (CrossFireTM Ready)
graphics card
DVI connector
Connect the DVI-DMS
cable to DVI connector of
the compatible standard
Radeon (CrossFireTM
Ready) graphics card.
There are two DVI connectors on the
standard Radeon (CrossFireTM Ready)
graphics card. Please connect the DVI-DMS
cable to the correct DVI connector; otherwise
, the graphics card will not work.
21
Radeon
CrossFireTM
DMS
connector
Edition graphics
card
Connect the DVI-DMS
cable to the monitor
Connect the DVI-DMS
cable to DMS connector
of the CrossFireTM Edition
connector.
graphics card.
If you install two CrossFireTM Edition graphics cards to this motherboard, please
connect one end of DVI-DMS cable to the monitor, another end to DMS of one
of the CrossFireTM Edition graphics cards to PCIE1 slot, and the other end to
DVI of another CrossFireTM Edition graphics card to AGI Express slot (PCI
Express x4). If you install one CrossFireTM Edition graphics card and one
compatible standard Radeon (CrossFireTM Ready) graphics card to this
motherboard, please connect one end of DVI-DMS cable to the monitor,
another end to DMS of the CrossFireTM Edition graphics card, and the other end
to DVI of the compatible standard Radeon (CrossFireTM Ready) graphics card.
Step 5.
Step 6.
Power on your computer and boot into OS.
Remove the ATITM driver if you have any VGA driver installed in your system.
The Catalyst Uninstaller is an optional download. We recommend using this
utility to uninstall any previously installed Catalyst drivers prior to installation.
Please visit this website for the driver:
http://support.ati.com/ics/support/DLRedirect.asp?
fileIDExt=050553d40196ef109fff37cbb40aaf28&accountID=737&deptID=894
Step 7.
Install the required drivers to your system. Please visit the websites below
for installing the drivers that ATITM recommends:
A. ATITM recommends Windows® XP Service Pack 2 or higher to be
installed (If you have Windows® XP Service Pack 2 or higher installed
in your system, there is no need to download it again):
http://www.microsoft.com/windowsxp/sp2/default.mspx
B. You must have Microsoft .NET Framework installed prior to
downloading and installing the CATALYST Control Center:
http://www.microsoft.com/downloads/details.aspx?
FamilyId=262D25E3-F589-4842-8157-034D1E7CF3A3&displaylang=en
Step 8.
Restart your computer.
22
Step 9.
Install the VGA card drivers to your system, and restart your computer.
Then you will find “ATI Catalyst Control Center” on your desktop.
You will find “ATI Catalyst
Control Center” on your
desktop.
Step 10. Double-click “ATI Catalyst Control Center”. Click “View”, and select “Advanced View”. Click “CrossFire TM”, and then set the option “Enable
CrossFire TM” to “Yes”.
View
CrossFireTM
Enable CrossFireTM
If you install one Radeon CrossFireTM Edition graphics card and one compatible
standard Radeon (CrossFireTM Ready) graphics card to this motherboard but
not two Radeon CrossFireTM Edition graphics cards, please as well follow the
above steps. However, although you have selected the option “Enable
CrossFireTM”, the CrossFireTM function can not work actually. Your computer
will automatically reboot. After restarting your computer, please confirm whether
the option “Enable CrossFireTM” in “ATI Catalyst Control Center” is selected or
not; if not, please select it again, and then you are able to enjoy the benefit of
CrossFireTM feature.
Step 11. You can freely enjoy the benefit of CrossFireTM feature.
23
2.8 Surround Display Feature
This motherboard supports Surround Display upgrade. With the external add-on
PCI Express VGA card, you can easily enjoy the benefits of Surround Display
feature. For the detailed instruction, please refer to the document at the following
path in the Support CD:
..\ Surround Display Information
2.9 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when jumper cap is
placed on these 2 pins.
Jumper
Setting
PS2_USB_PWR1
2_3
1_2
Description
Short pin2, pin3 to enable
(see p.11 No. 1)
+5VSB (standby) for PS/2
+5V
+5VSB
or USB wake up events.
Note: To select +5VSB, it requires 2 Amp and higher standby current provided by
power supply.
Clear CMOS
(CLRCMOS1, 2-pin jumper)
(see p.11 No. 11)
2-pin jumper
Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system
setup parameters. To clear and reset the system parameters to default setup,
please turn off the computer and unplug the power cord from the power
supply. After waiting for 15 seconds, use a jumper cap to short 2 pins on
CLRCMOS1 for 5 seconds.
2.10 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
24
FDD connector
(33-pin FLOPPY1)
Pin1
(see p.11 No. 26)
FLOPPY1
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.11 No. 10)
PIN1
IDE1
connect the black end
connect the blue end
to the IDE devices
to the motherboard
80-conductor ATA 66/100 cable
Note: Please refer to the instruction of your IDE device vendor for the details.
Serial ATA II Connectors
(SATAII_RED (PORT2):
These four Serial ATA II
(SATAII) connectors support
SATAII_ORANGE SATA data cables for internal
SATAII_RED
(PORT3)
(PORT2)
storage devices. The current
SATA II interface allows up to
3.0 Gb/s data transfer rate.
SATAII_BLUE SATAII_BLACK
see p.11, No. 13)
(PORT0)
(SATAII_BLUE (PORT0):
see p.11, No. 16)
(SATAII_BLACK (PORT1):
see p.11, No. 15)
(PORT1)
(SATAII_ORANGE (PORT3):
see p.11, No. 14)
SATAII_RED (PORT2) and SATAII_ORANGE (PORT3) connectors can be
used for internal storage devices or be connected to eSATAII_BOTTOM
and eSATAII_TOP connectors with corresponding color to support eSATAII
devices. Please read “eSATAII Interface Introduction” on page 31 for
(eSATAII_TOP: see p.11, No. 37)
(eSATAII_BOTTOM: see p.11, No. 38)
eSATAII_TOP
eSATA II Connectors
eSATAII_BOTTOM
details about eSATAII and eSATAII installation procedures.
Serial ATA (SATA)
Data Cable
These two eSATA II
connectors support SATA
data cables for external
SATAII function. The current
eSATA II interface allows up to
3.0 Gb/s data transfer rate.
Either end of the SATA data cable
can be connected to the SATA /
SATAII hard disk or the SATAII
connector on the motherboard.
You can also use the SATA data
cable to connect SATAII connectors and eSATAII connectors
with corresponding color.
(Optional)
25
Serial ATA (SATA)
Power Cable
(Optional)
connect to the
power supply
connect to the SATA HDD
power connector
USB 2.0 Headers
USB_PWR
P-7
P+7
GND
DUMMY
(9-pin USB67)
(see p.11 No. 21)
1
GND
P+6
P-6
USB_PWR
(9-pin USB45)
(see p.11 No. 23)
Please connect the black end of
SATA power cable to the power
connector on each drive. Then
connect the white end of SATA
power cable to the power
connector of the power supply.
Besides two default USB 2.0
ports on the I/O panel, there are
three USB 2.0 headers on this
motherboard. Each USB 2.0
header can support two USB
2.0 ports.
USB_PWR
P-5
P+5
GND
DUMMY
1
GND
P+4
P-4
USB_PWR
(9-pin USB23)
(see p.11 No. 24)
USB_PWR
P-3
P+3
GND
DUMMY
1
GND
P+2
P-2
USB_PWR
IRTX
+5VSB
DUMMY
Infrared Module Header
(5-pin IR1)
(see p.11 No. 20)
This header supports an
optional wireless transmitting
and receiving infrared module.
1
GND
IRRX
Internal Audio Connectors
(4-pin CD1)
(CD1: see p.11 No. 28)
This connector allows you
to receive stereo audio input
from sound sources such as
a CD-ROM, DVD-ROM, TV
tuner card, or MPEG card.
CD-L
GND
GND
CD-R
CD1
26
GND
PRESENCE#
MIC_RET
OUT_RET
Front Panel Audio Header
(9-pin HD_AUDIO1)
(see p.11 No. 29)
This is an interface for front
panel audio cable that allows
convenient connection and
control of audio devices.
1
OUT2_L
J_SENSE
OUT2_R
MIC2_R
MIC2_L
1. High Definition Audio supports Jack Sensing, but the panel wire on the
chassis must support HDA to function correctly. Please follow the
instruction in our manual and chassis manual to install your system.
2. If you use AC’97 audio panel, please install it to the front panel audio
header as below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for HD audio panel only. You don’t
need to connect them for AC’97 audio panel.
E. Enter BIOS Setup Utility. Enter Advanced Settings, and then select
Chipset Configuration. Set the Front Panel Control option from
[Auto] to [Enabled].
F. Enter Windows system. Click the icon on the lower right hand
taskbar to enter Realtek HD Audio Manager. Click “Audio I/O”, select
“Connector Settings”
, choose “Disable front panel jack
detection”, and save the change by clicking “OK”.
System Panel Header
PLED+
PLEDPWRBTN#
GND
(9-pin PANEL1)
(see p.11 No. 18)
1
This header accommodates
several system front panel
functions.
DUMMY
RESET#
GND
HDLEDHDLED+
Chassis Speaker Header
1
SPEAKER
DUMMY
DUMMY
+5V
(4-pin SPEAKER 1)
(see p.11 No. 19)
Chassis Fan Connector
GND
+12V
CHA_FAN_SPEED
(3-pin CHA_FAN1)
(see p.11 No. 17)
CPU Fan Connector
(4-pin CPU_FAN1)
+12V
CPU_FAN_SPEED
FAN_SPEED_CONTROL
GND
(see p.11 No. 6)
1 2 3 4
27
Please connect the chassis
speaker to this header.
Please connect a chassis fan
cable to this connector and
match the black wire to the
ground pin.
Please connect a CPU fan cable
to this connector and match
the black wire to the ground pin.
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin
CPU fan still can work successfully even without the fan speed control function.
If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this
motherboard, please connect it to Pin 1-3.
Pin 1-3 Connected
3-Pin Fan Installation
ATX Power Connector
Please connect an ATX power
supply to this connector.
(20-pin ATXPWR1)
(see p.11 No. 35)
ATX 12V Connector
Please connect an ATX 12V
(4-pin ATX12V1)
power supply to this connector.
(see p.11 No. 2)
SLI/XFIRE Power Connector
(4-pin SLI/XFIRE_POWER1)
(see p.11 No. 3)
SLI/XFIRE_POWER1
Game Port Header
+5V
JBB1
JBX
MIDI_OUT
JBY
JBB2
MIDI_IN
(15-pin GAME1)
(see p.11 No. 27)
It is not necessary to use this
connector, but please connect it
with a hard disk power connecor
when two graphics cards are
plugged to this motherboard at
the same time.
Connect a Game cable to this
header if the Game port bracket
is installed.
1
+5V
JAB2
JAY
GND
GND
JAX
JAB1
+5V
IEEE 1394 Headers
RXTPAM_0
GND
RXTPBM_0
+12V
GND
(9-pin FRONT_1394)
(see p.11 No. 25)
1
+12V
RXTPBP_0
GND
RXTPAP_0
RXTPAM_0
GND
RXTPBM_0
+12V
GND
(9-pin BACK_1394)
(see p.11 No. 31)
1
+12V
RXTPBP_0
GND
RXTPAP_0
28
There are two IEEE 1394
headers on this motherboard,
including one front panel IEEE
1394 header (FRONT_1394) and
one back panel IEEE 1394 header
(BACK_1394). Each IEEE 1394
header can support one IEEE
1394 port.
HDMI_SPDIF Header
(3-pin HDMI_SPDIF1)
HDMI_SPDIF header, providing
SPDIF audio output to HDMI VGA
card, allows the system to
connect HDMI Digital TV/
projector/LCD devices. Please
connect the HDMI_SPDIF
connector of HDMI VGA card to
this header.
1
(see p.11 No. 30)
+5V
GND
SPDIFOUT
HDMI_SPDIF Cable
Please connect the black end (A)
of HDMI_SPDIF cable to the
HDMI_SPDIF header on the
motherboard. Then connect the
white end (B or C) of
HDMI_SPDIF cable to the
HDMI_SPDIF connector of HDMI
VGA card.
C
(Optional)
B
A
A. black end
B. white end (2-pin)
+5V
SPDIFOUT
GND
SPDIFOUT
GND
blue
black
C. white end (3-pin)
SPDIFOUT
GND
blue
black
blue
black
USB+1394 Bracket
This USB+1394 bracket can
support 2 additional USB 2.0
ports and 1 IEEE 1394 port.
Please connect the blue connector on the cable of this USB+1394
bracket to the USB 2.0 header
(USB23, USB45, or USB67),
and connect the red connector
on the cable of this USB+1394
bracket to the IEEE 1394 header
(BACK_1394). Then fasten the
USB+1394 bracket to the
chassis with screws.
29
2.11 HDMI_SPDIF Header Connection Guide
HDMI (High-Definition Multi-media Interface) is an all-digital audio/video
specification, which provides an interface between any compatible digital audio/
video source, such as a set-top box, DVD player, A/V receiver and a compatible
digital audio or video monitor, such as a digital television (DTV). A complete HDMI
system requires a HDMI VGA card and a HDMI ready motherboard with a
HDMI_SPDIF header. This motherboard is equipped with a HDMI_SPDIF header,
which provides SPDIF audio output to HDMI VGA card, allows the system to
connect HDMI Digital TV/projector/LCD devices. To use HDMI function on this
motherboard, please carefully follow the below steps.
Step 1. Install the HDMI VGA card to the• PCI Express Graphics slot on this
Step 2.
motherboard. For the proper installation of HDMI VGA card, please refer
to the installation guide on page 19.
Connect the black end (A) of HDMI_SPDIF cable to the
HDMI_SPDIF header (HDMI_SPDIF1, yellow, see page 11, No.
30) on the motherboard.
Make sure to correctly connect the HDMI_SPDIF cable to the motherboard and the
HDMI VGA card according to the same pin definition. For the pin definition of
HDMI_SPDIF header and HDMI_SPDIF cable connectors, please refer to page 29. For
the pin definition of HDMI_SPDIF connectors on HDMI VGA card, please refer to the
user manual of HDMI VGA card vendor. Incorrect connection may cause permanent
damage to this motherboard and the HDMI VGA card.
Step 3.
Connect the white end (B or C) of HDMI_SPDIF cable to the HDMI_SPDIF
connector of HDMI VGA card. (There are two white ends (2-pin and 3-pin)
on HDMI_SPDIF cable. Please choose the appropriate white end according
to the HDMI_SPDIF connector of the HDMI VGA card you install.
white end
white end
(2-pin) (B)
(3-pin) (C)
Please do not connect the white end of HDMI_SPDIF cable to the wrong connector
of HDMI VGA card or other VGA card. Otherwise, the motherboard and the
VGA card may be damaged. For example, this picture shows the wrong
example of connecting HDMI_SPDIF cable to the fan connector of PCI
Step 4.
Step 5.
Express VGA card. Please refer to the VGA card user manual for
connector usage in advance.
Connect the HDMI output connector on HDMI VGA card to
HDMI device, such as HDTV. Please refer to the user manual
of HDTV and HDMI VGA card vendor for detailed connection
procedures.
Install HDMI VGA card driver to your system.
30
2.12 eSA
eSATTAII Inter face Introduction
What is eSATAII?
This motherboard supports eSATAII interface, the external SATAII specification.
eSATAII allows you to enjoy the SATAII function provided by the I/O of your
computer, offering the high speed data transfer rate up to 3.0Gb/s, and the
convenient mobility like USB. eSATAII is equipped with Hot Plug capability that
enables you to exchange drives easily. For example, with eSATAII interface, you
may simply plug your eSATAII hard disk to the eSATAII ports instead of opening
your chassis to exchange your SATAII hard disk. Currently, on the market, the
data transfer rate of USB 2.0 is up to 480Mb/s, and for IEEE 1394 is up to 400Mb/
s. However, eSATAII provides the data transfer rate up to 3000Mb/s, which is
much higher than USB 2.0 and IEEE 1394, and still keeps the convenience of Hot
Plug feature. Therefore, on the basis of the advantageous transfer speed and the
facilitating mobile capability, in the near future, eSATAII will replace USB 2.0 and
IEEE 1394 to be a trend for external interface.
NOTE:
1. If you set “Configure SATA as” option in BIOS setup to AHCI or RAID mode, Hot
Plug function is supported with eSATAII devices. Therefore, you can insert or
remove your eSATAII devices to the eSATAII ports while the system is power-on and
in working condition.
2. If you set “Configure SATA as” option in BIOS setup to IDE mode, Hot Plug function
is not supported with eSATAII devices. If you still want to use eSATAII function in IDE
mode, please insert or remove your eSATAII devices to the eSATAII ports only when
the system is power-off.
3. Please refer to page 36 to 42 for detailed information of RAID mode, IDE mode, and
AHCI mode.
How to install eSATAII?
SATAII_RED (PORT2) and
SATAII_ORANGE (PORT3)
1.
eSATAII_TOP and
eSATAII_BOTTOM
If you just plan to install one eSATAII device to this motherboard, it is recommended to enable the bottom eSATAII port of the I/O shield. In order to enable
the bottom eSATAII port of the I/O shield, you need to connect the red SATAII
connector (SATAII_RED; see p.11 No.13) and the red eSATAII connector
(eSATAII_BOTTOM; see p.11 No.36) with a SATA data cable first. Then the
bottom eSATAII port of the I/O shield is enabled.
31
Connect the SATA
data cable to the red
SATAII connector
(SATAII_RED (PORT2))
2.
Connect the SATA
data cable to the red
eSATAII connector
(eSATAII_BOTTOM)
If you plan to install two eSATAII devices to this motherboard, you need to
enable both the top and the bottom eSATAII ports of the I/O shield. In order to
enable the top and the bottom eSATAII ports of the I/O shield, you have to
connect the red SATAII connector (SATAII_RED; see p.11 No.13) and the red
eSATAII connector (eSATAII_BOTTOM; see p.11 No.36) with a SATA data
cable first, and then connect the orange SATAII connector (SATAII_ORANGE;
see p.11 No.14) and the orange eSATAII connector (eSATAII_TOP; see p.11
No.37) with another SATA data cable. After that, both the top and the bottom
eSATAII ports of the I/O shield are enabled.
Connect the SATA
data cables to both
red SATAII connector
(SATAII_RED (PORT2))
and orange SATAII
connector (SATAII_
ORANGE (PORT3))
Connect the SATA
data cables to both
red eSATAII connector
(eSATAII_BOTTOM)
and orange eSATAII
connector (eSATAII_TOP)
Please make sure to correctly connect the SATAII and eSATAII connectors
with corresponding color so that the eSATAII function will work successfully.
32
3.
Use the eSATAII device cable to connect eSATAII device and the eSATAII port
of the I/O shield according to the eSATAII connector that you connect the
SATA data cable.
Connect one end of the eSATAII
device cable to eSATAII device
Connect the other end of the eSATAII
device cable to eSATAII port of the I/O
shield
Comparison between eSATAII and other devices
IEEE 1394
USB 2.0
SATA
eSATAII/SATAII
400Mb/s
480Mb/s
1.5Gb/s (1500Mb/s)
3.0Gb/s (3000Mb/s)
33
2.13 SA
SATTAII Hard Disk Setup Guide
Before installing SATAII hard disk to your computer, please carefully read below
SATAII hard disk setup guide. Some default setting of SATAII hard disks may not
be at SATAII mode, which operate with the best performance. In order to enable
SATAII function, please follow the below instruction with different vendors to
correctly adjust your SATAII hard disk to SATAII mode in advance; otherwise, your
SATAII hard disk may fail to run at SATAII mode.
Western Digital
7
5
3
1
8
6
4
2
If pin 5 and pin 6 are shorted, SATA 1.5Gb/s will be enabled.
On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the
jumpers from pin 5 and pin 6.
SAMSUNG
7
5
3
1
8
6
4
2
If pin 3 and pin 4 are shorted, SATA 1.5Gb/s will be enabled.
On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the
jumpers from pin 3 and pin 4.
HITACHI
Please use the Feature Tool, a DOS-bootable tool, for changing various ATA
features. Please visit HITACHI’s website for details:
http://www.hitachigst.com/hdd/support/download.htm
The above examples are just for your reference. For different SATAII hard
disk products of different vendors, the jumper pin setting methods may not
be the same. Please visit the vendors’ website for the updates.
34
2.14 Serial A
ATTA (SA
(SATTA) / Serial A
ATTAII (SA
(SATTAII) Hard Disks
Installation
This motherboard adopts Intel® ICH7R south bridge chipset that supports Serial
ATA (SATA) / Serial ATAII (SATAII) hard disks and RAID (RAID 0, RAID 1, RAID 10,
RAID 5, and Intel Matrix Storage) functions. You may install SATA / SATAII hard
disks on this motherboard for internal storage devices. This section will guide you
to install the SATA / SATAII hard disks.
STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis.
STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk.
STEP 3: Connect one end of the SATA data cable to the motherboard’s SATAII
connector.
STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard
disk.
1. If you plan to use RAID 0, RAID 1, or Intel Matrix Storage function, you
need to install at least 2 SATA / SATAII hard disks. If you plan to use
RAID 5 function, you need to install at least 3 SATA / SATAII hard disks.
If you plan to use RAID 10 function, you need to install at least 4 SATA /
SATAII hard disks. If you install 2 eSATAII devices, then only RAID 0,
RAID 1, or Intel Matrix Storage functions will be enabled.
2. It is not recommended to switch the “Configure SATA as” setting between
AHCI, RAID, and IDE mode after OS installation.
35
2.15 Hot Plug and Hot Swap FFunctions
unctions for SA
SATTA / SA
SATTAII
HDDs and eSA
eSATTAII Devices
This motherboard supports Hot Plug and Hot Swap functions for SATA / SATAII /
eSATAII Devices in RAID / AHCI mode. Intel® ICH7R south bridge chipset provides
hardware support for Advanced Host controller Interface (AHCI), a new
programming interface for SATA host controllers developed thru a joint industry
effort. AHCI also provides usability enhancements such as Hot Plug.
NOTE
What is Hot Plug Function?
If the SATA / SATAII HDDs are NOT set for RAID configuration, it is called
“Hot Plug” for the action to insert and remove the SATA / SATAII HDDs
while the system is still power-on and in working condition.
However, please note that it cannot perform Hot Plug if the OS has been
installed into the SATA / SATAII HDD.
What is Hot Swap Function?
If SATA / SATAII HDDs are built as RAID1 then it is called “Hot Swap” for
the action to insert and remove the SATA / SATAII HDDs while the system
is still power-on and in working condition.
eSATAII is equipped with Hot Plug capability that enables you to exchange
drives easily. For example, with eSATAII interface, you may simply plug your
eSATAII devices to the eSATAII ports instead of opening your chassis to
exchange your SATAII hard disk.
2.16 Driver Installation Guide
To install the drivers to your system, please insert the support CD to your optical
drive first. Then, the drivers compatible to your system can be auto-detected and
listed on the support CD driver page. Please follow the order from up to bottom
side to install those required drivers. Therefore, the drivers you install can work
properly.
2.17 Installing Windows ® 2000 / XP / XP 64-bit / Vista TM /
Vista TM 64-bit With RAID Functions
If you want to install Windows® 2000 / XP / XP 64-bit / VistaTM / VistaTM 64-bit OS
on your SATA / SATAII HDDs with RAID functions, please follow below procedures
according to the OS you install.
The installation procedures for Windows® VistaTM / VistaTM 64-bit are subject to
change. Please visit our website for the updates of Windows® VistaTM / VistaTM 64-bit
driver and related information in the future.
36
2.17.1 Installing Windows ® 2000 / XP / XP 64-bit With
RAID Functions
If you want to install Windows® 2000 / XP / XP 64-bit on your SATA / SATAII HDDs
with RAID functions, please follow below steps.
STEP 1: Set up BIOS.
A. Enter BIOS SETUP UTILITY
Advanced screen
IDE Configuration.
B. Set “ATA/IDE Configuration” to [Enhanced], and then in the option “Configure
SATA as”, please set the option to [RAID].
STEP 2: Make a SATA / SATAII Driver Diskette.
A. Insert the Support CD into your optical drive to boot your system.
B. During POST at the beginning of system boot-up, press <F11> key, and then a
window for boot devices selection appears. Please select CD-ROM as the boot
device.
C. When you see the message on the screen, “Do you want to generate Serial
ATA driver diskette [YN]?”, press <Y>.
D. Then you will see these messages,
Please insert a diskette into the floppy drive.
WARNING! Formatting the floppy diskette will
lose ALL data in it!
Start to format and copy files [YN]?
Please insert a floppy diskette into the floppy drive, and press <Y>.
E. The system will start to format the floppy diskette and copy SATA / SATAII
drivers into the floppy diskette.
STEP 3: Use “RAID Installation Guide” to set RAID configuration.
Before you start to configure the RAID function, you need to check the installation
guide in the Support CD for proper configuration. Please refer to the document in
the Support CD, “Guide to SATA Hard Disks Installation and RAID Configuration”,
which is located in the folder at the following path: .. \ RAID Installation Guide
STEP 4: Install Windows® 2000 / XP / XP 64-bit OS on your system.
After making a SATA / SATAII driver diskette and using “RAID Installation Guide” to
set RAID configuration, you can start to install Windows® 2000 / XP / XP 64-bit on
your system. At the beginning of Windows setup, press F6 to install a third-party
RAID driver. When prompted, insert the SATA / SATAII driver diskette containing
the Intel® RAID driver. After reading the floppy disk, the driver will be presented.
Select the driver to install according to the mode you choose and the OS you
install. You may select: “Intel(R) 82801GR/GH SATA RAID Controller (Desktop
ICH7R-Windows XP/2000)” for Windows® XP/2000 or “Intel(R) 82801GR/GH SATA
RAID Controller (Desktop ICH7R-Windows XP64)” for Windows® XP 64-bit.
37
After the installation of Windows® 2000 / Windows® XP / Windows® XP-64bit OS, if you want
to manage RAID functions, you are allowed to use both “RAID Installation Guide” and “Intel
Matrix Storage Manager Information” for RAID configuration. Please refer to the document
in the Support CD, “Guide to SATA Hard Disks Installation and RAID Configuration”, which
is located in the folder at the following path: .. \ RAID Installation Guide and the document
in the support CD, “Guide to Intel Matrix Storage Manager”, which is located in the folder at
the following path: .. \ Intel Matrix Storage Manager Information
If you want to use “Intel Matrix Storage Manager” in Windows® environment,
please install SATA / SATAII drivers from the Support CD again so that “Intel
Matrix Storage Manager” will be installed to your system as well.
2.17.2
Setting Up a “RAID Ready” System
You can also set up a “RAID Ready” system with a single SATA / SATAII hard disk.
A “RAID Ready” system can be seamlessly upgraded to RAID 0, RAID 1 or RAID 5
at a later date by using RAID migration feature of Intel Matrix Storage. The
following steps outline how to build an Intel “RAID Ready” system.
1. Assemble the system and attach a single SATA / SATAII hard drive.
2. Set up system BIOS as step 1 of page 37. When done, exit Setup.
3. Make a SATA / SATAII driver diskette as step 2 of page 37. Begin Windows®
setup by booting from the installation CD.
4. At the beginning of Windows® setup, press F6 to install a third-party RAID
driver. When prompted, insert the SATA / SATAII driver diskette containing the
Intel® RAID driver. After reading the floppy disk, the driver will be presented.
Select the driver to install according to the mode you choose and the OS you
install. You may select: “Intel(R) 82801GR/GH SATA RAID Controller (Desktop
ICH7R-Windows XP/2000)” for Windows® XP/2000 or “Intel(R) 82801GR/GH
SATA RAID Controller (Desktop ICH7R-Windows XP64)” for Windows® XP 64-bit.
5. Finish the Windows® installation and install all necessary drivers.
6. Install the Intel(R) Matrix Storage Manager software via the CD-ROM included
with your motherboard or after downloading it from the Internet. This will add
the Intel(R) Matrix Storage Console which can be used to manage the RAID
configuration.
7. After setting up a “RAID Ready” system as the above steps, you can follow the
procedures of the next section to migrate the system to RAID 0, RAID 1 or RAID
5.
38
2.17.3
Migrating a “RAID Ready” System to RAID 0,
RAID 1 or RAID 5
If you have an existing “RAID Ready” system, then you can use the following
steps to perform a migration from a single non-RAID configuration to a two drive
RAID 0, RAID 1 configuration or three drive RAID 5 configuration. To prepare for
this, you will need another SATA / SATAII hard drive with a capacity equal to or
greater than that currently being used as the source hard drive.
1. Physically attach one additional SATA / SATAII hard drive to the SATAII port not
being used. Note the serial number of the hard drive already in the system; you
will use this to select it as the source hard drive when initiating the migration.
2. Boot Windows®, install the Intel(R) Matrix Storage Manager software, if not
already installed, using the setup package obtained from a CD-ROM or from the
Internet. This will install the necessary Intel Storage Utility and start menu links.
3. Open the Intel Storage Utility from the Start Menu and select “Create RAID
volume from Existing Hard Drive” from the Actions menu. This will activate the
Create RAID volume from Existing Hard Drive Wizard. Click through the dialogs
as prompted. It’s important to understand what will occur during the migration
process because any data on the destination hard drive will be lost.
4. Once the migration is complete, reboot the system. If you migrated to a RAID 0
volume, use Disk Management from within Windows® in order to partition and
format the empty space created when the two hard drive capacities are
combined. You may also use third-party software to extend any existing
partitions within the RAID volume.
2.17.4 Installing Windows ® Vista TM / Vista TM 64-bit With
RAID Functions
If you want to install Windows® VistaTM / VistaTM 64-bit on your SATA / SATAII
HDDs with RAID functions, please follow below steps.
STEP 1: Set up BIOS.
A. Enter BIOS SETUP UTILITY
Advanced screen
IDE Configuration.
B. Set “ATA/IDE Configuration” to [Enhanced], and then in the option “Configure
SATA as”, please set the option to [RAID].
STEP 2: Use “RAID Installation Guide” to set RAID configuration.
Before you start to configure the RAID function, you need to check the installation
guide in the Support CD for proper configuration. Please refer to the document in
the Support CD, “Guide to SATA Hard Disks Installation and RAID Configuration”,
which is located in the folder at the following path: .. \ RAID Installation Guide
39
STEP 3: Install Windows® Vista TM / VistaTM 64-bit OS on your system.
Insert the Windows® VistaTM / VistaTM 64-bit optical disk into the optical drive to boot
your system, and follow the instruction to install Windows ® Vista TM / VistaTM 64-bit
OS on your system. When you see “Where do you want to install Windows?” page,
please insert the ASRock Support CD into your optical drive, and click the “Load
Driver” button on the left on the bottom to load the Intel ® RAID drivers. Intel® RAID
drivers are in the following path in our Support CD:
.. \ I386 \ Vista (For Windows® VistaTM OS)
.. \ AMD64 \ Vista64 (For Windows® VistaTM 64-bit OS)
After that, please insert Windows® VistaTM / VistaTM 64-bit optical disk into the optical
drive again to continue the installation.
After the installation of Windows® VistaTM / VistaTM 64-bit OS, if you want to manage RAID
functions, you are allowed to use both “RAID Installation Guide” and “Intel Matrix Storage
Manager Information” for RAID configuration. Please refer to the document in the Support
CD, “Guide to SATA Hard Disks Installation and RAID Configuration”, which is located in the
folder at the following path: .. \ RAID Installation Guide and the document in the support
CD, “Guide to Intel Matrix Storage Manager”, which is located in the folder at the following
path: .. \ Intel Matrix Storage Manager Information
If you want to use “Intel Matrix Storage Manager” in Windows® environment,
please install SATA / SATAII drivers from the Support CD again so that “Intel
Matrix Storage Manager” will be installed to your system as well.
2.18 Installing Windows ® 2000 / XP / XP 64-bit / Vista TM /
Vista TM 64-bit Without RAID Functions
If you want to install Windows® 2000 / XP / XP 64-bit / VistaTM / VistaTM 64-bit OS
on your SATA / SATAII HDDs without RAID functions, please follow below
procedures according to the OS you install.
The installation procedures for Windows® VistaTM / VistaTM 64-bit are subject to
change. Please visit our website for the updates of Windows® VistaTM / VistaTM 64-bit
driver and related information in the future.
2.18.1
Installing Windows ® 2000 / XP / XP 64-bit Without
RAID Functions
If you want to install Windows® 2000 / XP / XP 64-bit OS on your SATA / SATAII
HDDs without RAID functions, please follow below steps.
Using SATA / SATAII HDDs and eSATAII devices with NCQ and Hot Plug
functions
40
STEP 1: Set Up BIOS.
A.
Enter BIOS SETUP UTILITY
Advanced screen
IDE Configuration.
B.
Set “ATA/IDE Configuration” to [Enhanced], and then in the option
“Configure SATA as”, please set the option to [AHCI].
STEP 2: Make a SATA / SATAII driver diskette.
Please make a SATA / SATAII driver diskette by following section 2.17.1 step 2 on
page 37.
If you want to enable Hot Plug function on eSATAII ports but you install OS
on IDE HDD, please skip step 2.
STEP 3: Install Windows® 2000 / XP / XP 64-bit OS on your system.
After making a SATA / SATAII driver diskette, you can start to install Windows® 2000
/ XP / XP 64-bit on your system. At the beginning of Windows® setup, press F6 to
install a third-party AHCI driver. When prompted, insert the SATA / SATAII driver
diskette containing the Intel® AHCI driver. After reading the floppy disk, the driver will
be presented. Select the driver to install according to the mode you choose and the
OS you install. You may select: “Intel(R) 82801GR/GH SATA AHCI Controller (Desktop
ICH7R-Windows XP/2000)” for Windows® XP/2000 or “Intel(R) 82801GR/GH SATA
AHCI Controller (Desktop ICH7R-Windows XP64)” for Windows® XP 64-bit.
Using SATA / SATAII HDDs and eSATAII devices without NCQ and Hot Plug
functions
STEP 1: Set up BIOS.
A.
Enter BIOS SETUP UTILITY
Advanced screen
IDE Configuration.
B.
Set “ATA/IDE Configuration” to [Enhanced], and then in the option
“Configure SATA as”, please set the option to [IDE].
STEP 2: Install Windows® 2000 / XP / XP 64-bit OS on your system.
2.18.2
Installing Windows ® Vista TM / Vista TM 64-bit Without
RAID Functions
If you want to install Windows® VistaTM / VistaTM 64-bit OS on your SATA / SATAII
HDDs without RAID functions, please follow below steps.
Using SATA / SATAII HDDs and eSATAII devices with NCQ and Hot Plug
functions
STEP 1: Set Up BIOS.
A.
Enter BIOS SETUP UTILITY
Advanced screen
IDE Configuration.
B.
Set “ATA/IDE Configuration” to [Enhanced], and then in the option
“Configure SATA as”, please set the option to [AHCI].
41
STEP 2: Install Windows® Vista TM / VistaTM 64-bit OS on your system.
After setting up BIOS, you can start to install Windows® VistaTM / VistaTM 64-bit on
your system.
Using SATA / SATAII HDDs and eSATAII devices without NCQ and Hot Plug
functions
STEP 1: Set up BIOS.
A.
Enter BIOS SETUP UTILITY
Advanced screen
IDE Configuration.
B.
Set “ATA/IDE Configuration” to [Enhanced], and then in the option
“Configure SATA as”, please set the option to [IDE].
STEP 2: Install Windows® Vista TM / VistaTM 64-bit OS on your system.
After setting up BIOS, you can start to install Windows® VistaTM / VistaTM 64-bit on
your system.
2.19 Untied Overclocking TTechnology
echnology
This motherboard supports Untied Overclocking Technology, which means during
overclocking, FSB enjoys better margin due to fixed PCI bus. You may set “CPU
Host Frequency” option of BIOS setup to [Auto], which will show you the actual
CPU host frequency in the following item. Therefore, CPU FSB is untied during
overclocking, but PCI bus is in the fixed mode so that FSB can operate under a
more stable overclocking environment.
Please refer to the warning on page 7 for the possible overclocking risk before
you apply Untied Overclocking Technology.
42
Chapter 3 BIOS SETUP UTILITY
3.1
Introduction
This section explains how to use the BIOS SETUP UTILITY to configure your system.
The BIOS FWH chip on the motherboard stores the BIOS SETUP UTILITY. You may
run the BIOS SETUP UTILITY when you start up the computer. Please press <F2>
during the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise,
POST will continue with its test routines.
If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by
pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You may also restart by turning the system off and then back on.
Because the BIOS software is constantly being updated, the
following BIOS setup screens and descriptions are for reference purpose only, and they may not exactly match what you
see on your screen.
3.1.1 BIOS Menu Bar
The top of the
Main
Advanced
H/W Monitor
Boot
screen has a menu bar with the following selections:
To set up the system time/date information
To set up the advanced BIOS features
To display current hardware status
To set up the default system device to locate and load the
Operating System
Security
To set up the security features
Exit
To exit the current screen or the BIOS SETUP UTILITY
Use < > key or < > key to choose among the selections on the menu bar,
and then press <Enter> to get into the sub screen.
43
3.1.2 Navigation Keys
Please check the following table for the function description of each navigation
key.
Navigation Key(s)
/
/
+ / <Enter>
<F1>
<F9>
<F10>
<ESC>
Function Description
Moves cursor left or right to select Screens
Moves cursor up or down to select items
To change option for the selected items
To bring up the selected screen
To display the General Help Screen
To load optimal default values for all the settings
To save changes and exit the BIOS SETUP UTILITY
To jump to the Exit Screen or exit the current screen
3.2 Main Screen
When you enter the BIOS SETUP UTILITY, the Main screen will appear and display
the system overview
Advanced
Main
BIOS SETUP UTILITY
H/W Monitor
Boot
System Overview
System Time
System Date
[14:00:09]
[Wed 05/10/2006]
: ConRoeXFire-eSATA2 BIOS P1.00
: Intel (R) CPU 3.40 GHz
(64bit supported)
: 3400 MHz
Processor Speed
Microcode Update : F34/17
: 1024KB
Cache Size
BIOS Version
Processor Type
Total Memory
DDRII 1
DDRII 2
DDRII 3
DDRII 4
: 256MB
Single-Channel Memory Mode
: 256MB/266MHz (DDRII533)
: None
: None
: None
Security
Exit
Use [Enter], [TAB]
or [SHIFT-TAB] to
select a field.
Use [+] or [-] to
configure system Time.
+Tab
F1
F9
F10
ESC
Select Screen
Select Item
Change Field
Select Field
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
System Time [Hour:Minute:Second]
Use this item to specify the system time.
System Date [Day Month/Date/Year]
Use this item to specify the system date.
3.3 Advanced Screen
In this section, you may set the configurations for the following items: CPU
Configuration, Chipset Configuration, ACPI Configuration, IDE Configuration, PCIPnP
Configuration, Floppy Configuration, SuperIO Configuration, and USB Configuration.
44
Main
BIOS SETUP UTILITY
H/W Monitor
Boot
Advanced
Security
Exit
Configure CPU
Advanced Settings
WARNING : Setting wrong values in below sections
may cause system to malfunction.
CPU Configuration
Chipset Configuration
ACPI Configuration
IDE Configuration
PCIPnP Configuration
Floppy Configuration
SuperIO Configuration
USB Configuration
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
Setting wrong values in this section may cause
the system to malfunction.
3.3.1 CPU Configuration
BIOS SETUP UTILITY
Advanced
Select how to set the
CPU host frequency.
CPU Configuration
CPU Host Frequency
Actual Frequency (MHz)
Boot Failure Guard
Spread Spectrum
Ratio Status
Ratio Actual Value
[Auto]
[200]
[Enabled]
[Auto]
Unlocked (Max :17, Min : 14)
17
Enhance Halt State
Max CPUID Value Limit
Intel (R) Virtualization tech.
CPU Thermal Throttling
No-Excute Memory Protection
Hyper Threading Technology
Intel (R) SpeedStep(tm) tech.
[Disabled]
[Disabled]
[Enabled]
[Enabled]
[Disabled]
[Enabled]
[Auto]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
CPU Host Frequency
While entering setup, BIOS auto detects the present CPU host frequency of
this motherboard. The actual CPU host frequency will show in the following
item.
Boot Failure Guard
Enable or disable the feature of Boot Failure Guard.
Spread Spectrum
This item should always be [Auto] for better system stability.
Ratio Status
This is a read-only item, which displays whether the ratio status of this
motherboard is “Locked” or “Unlocked”. If it shows “Unlocked”, you will find
an item Ratio CMOS Setting appears to allow you changing the ratio
value of this motherboard.
45
Ratio Actual Value
This is a read-only item, which displays the ratio actual value of this
motherboard.
Ratio CMOS Setting
If the ratio status is unlocked, you will find this item appear to allow you
changing the ratio value of this motherboard. If the CPU you adopt supports
EIST (Intel (R) SpeedStep(tm) tech.), and you plan to adjust the ratio value,
please disable the option “ Intel (R) SpeedStep(tm) tech.” in advance.
Enhance Halt State
All processors support the Halt State (C1). The C1 state is supported
through the native processor instructions HLT and MWAIT and requires no
hardware support from the chipset. In the C1 power state, the processor
maintains the context of the system caches.
Max CPUID Value Limit
For Prescott CPU only, some OSes (ex. NT4.0) cannot handle the function
with disable. This should be enabled in order to boot legacy OSes that
cannot support CPUs with extended CPUID functions.
Intel (R) Virtualization tech.
When this option is set to [Enabled], a VMM (Virtual Machine Architecture)
can utilize the additional hardware capabilities provided by Vanderpool
Technology. This option will be hidden if the installed CPU does not support
Intel (R) Virtualization Technology.
CPU Thermal Throttling
You may select [Enabled] to enable P4 CPU internal thermal control mechanism to keep the CPU from overheated.
No-Excute Memory Protection
No-Execution (NX) Memory Protection Technology is an enhancement to
the IA-32 Intel Architecture. An IA-32 processor with “No Execute (NX)
Memory Protection” can prevent data pages from being used by malicious
software to execute code. This option will be hidden if the current CPU
does not support No-Excute Memory Protection.
Hyper Threading Technology
To enable this feature, it requires a computer system with an Intel Pentium®
4 processor that supports Hyper-Threading technology and an operating
system that includes optimization for this technology, such as Microsoft®
Windows® XP. Set to [Enabled] if using Microsoft® Windows® XP, or Linux
kernel version 2.4.18 or higher. This option will be hidden if the installed
CPU does not support Hyper-Threading technology.
46
Intel (R) SpeedStep(tm) tech.
Intel (R) SpeedStep(tm) tech. is Intel’s new power saving technology.
Processor can switch between multiple frequency and voltage points to
enable power savings. The default value is [Auto]. Configuration options:
[Auto], [Enabled] and [Disabled]. If you install Windows® XP and select
[Auto], you need to set the “Power Schemes” as “Portable/Laptop” to enable this function. If you install Windows® VistaTM and want to enable this
function, please set this item to [Enabled]. This item will be hidden if the
current CPU does not support Intel (R) SpeedStep(tm) tech..
Please note that enabling this function may reduce CPU voltage and lead to system
stability or compatibility issue with some power supplies. Please set this item to
[Disable] if above issue occurs.
3.3.2 Chipset Configuration
BIOS SETUP UTILITY
Advanced
Chipset Configuration
Options
Auto
200MHz
266MHz
333 MHz
[Auto]
DRAM Frequency
[Disabled]
Flexibility Option
Configure DRAM Timing by SPD [Enabled]
[Auto]
DRAM CAS# Latency
Primary Graphics Adapter
[PCI]
OnBoard HD Audio
Front Panel Control
CD-In
OnBoard LAN
[Auto]
[Auto]
[Enabled]
[Enabled]
VCCM (DRAM) Voltage
+1.5V Voltage
[Auto]
[Normal]
+F1
F9
F10
ESC
(DDRII400)
(DDRII533)
(DDRII667)
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
DRAM Frequency
If [Auto] is selected, the motherboard will detect the memory module(s)
inserted and assigns appropriate frequency automatically. You may also
select other value as operating frequency: [200MHz (DDRII 400)], [266MHz
(DDRII 533)], [333MHz (DDRII 667)].
Flexibility Option
The default value of this option is [Disabled]. It will allow better tolerance for
memory compatibility when it is set to [Enabled].
Configure DRAM Timing by SPD
Select [Enabled] will configure the following items by the contents in the
SPD (Serial Presence Detect) device. If you select [Disabled], you will find
the items “DRAM RAS# to CAS# Delay”, “DRAM RAS# Precharge”, and
“DRAM RAS# Activate to Precharge” appear to allow you adjusting them.
47
DRAM CAS# Latency
Use this item to adjust the means of memory accessing. Configuration
options are [6], [5], [4], [3], and [Auto].
DRAM RAS# to CAS# Delay
This controls the latency between the DRAM active command and the
read / write command. Configuration options: [2 DRAM Clocks], [3 DRAM
Clocks], [4 DRAM Clocks], [5 DRAM Clocks], and [6 DRAM Clocks].
DRAM RAS# Precharge
This controls the idle clocks after a precharge command is issued.
Configuration options: [2 DRAM Clocks], [3 DRAM Clocks], [4 DRAM
Clocks], [5 DRAM Clocks], and [6 DRAM Clocks].
DRAM RAS# Activate to Precharge
This controls the number of DRAM clocks for TRAS. Configuration options:
[4 DRAM Clocks], [5 DRAM Clocks], [6 DRAM Clocks], [7 DRAM Clocks], [8
DRAM Clocks], [9 DRAM Clocks], [10 DRAM Clocks], [11 DRAM Clocks], [12
DRAM Clocks], [13 DRAM Clocks], [14 DRAM Clocks], a n d [ 1 5 D R A M
Clocks].
Primary Graphics Adapter
This allows you to select [PCI] or [PCI Express] as the boot graphic adapter
priority. The default value is [PCI].
OnBoard HD Audio
Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio feature. If
you select [Auto], the onboard HD Audio will be disabled when PCI Sound
Card is plugged.
Front Panel Control
Select [Auto], [Enabled] or [Disabled] for the onboard HD Audio Front Panel.
CD-In
Use this item to enable or disable CD-In of OnBoard HD Audio.
OnBoard LAN
This allows you to enable or disable the “OnBoard LAN” feature.
VCCM (DRAM) Voltage
Use this to select VCCM (DRAM) Voltage. Configuration options: [High],
[Middle], [Low], and [Auto]. The default value of this feature is [Auto].
+1.5V Voltage
Configuration options: [High] and [Normal]. The default value of this feature
is [Normal].
48
3.3.3 ACPI Configuration
BIOS SETUP UTILITY
Advanced
ACPI Configuration
Suspend To RAM
[Disabled]
Restore on AC/Power Loss
Ring-In Power On
PCI Devices Power On
PS / 2 Keyboard Power On
RTC Alarm Power On
[Power Off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
ACPI HPET Table
[Disabled]
Select auto-detect or
disable the STR
feature.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
Suspend to RAM
This field allows you to select whether to auto-detect or disable the Sus
pend-to-RAM feature. Select [Auto] will enable this feature if the system
supports it.
Restore on AC/Power Loss
This allows you to set the power state after an unexpected AC/
Power loss. If [Power Off] is selected, the AC/Power remains off
when the power recovers. If [Power On] is selected, the AC/Power
resumes and the system starts to boot up when the power recovers.
Ring-In Power On
Use this item to enable or disable Ring-In signals to turn on the system from
the power-soft-off mode.
PCI Devices Power On
Use this item to enable or disable PCI devices to turn on the system from the
power-soft-off mode.
PS/2 Keyboard Power On
Use this item to enable or disable PS/2 keyboard to turn on the system from
the power-soft-off mode.
RTC Alarm Power On
Use this item to enable or disable RTC (Real Time Clock) to power on the
system.
ACPI HPET Table
Use this item to enable or disable ACPI HPET Table. The default value is
[Disabled]. Please set this option to [Enabled] if you plan to use this
motherboard to submit Windows® VistaTM certification.
49
3.3.4 IDE Configuration
BIOS SETUP UTILITY
Advanced
Set [Compatible]
when Legacy OS
(MS-DOS, WinNT)
is used.
IDE Configuration
ATA/IDE Configuration
Configure SATA as
SATAII_BLUE
SATAII_BLACK
SATAII_RED
SATAII_ORANGE
IDE1 Master
IDE1 Slave
(PORT0)
(PORT1)
(PORT2)
(PORT3)
[Enhanced]
[AHCI]
[Hard Disk]
[Not Detected]
[Not Detected]
[Not Detected]
[ATAPI CDROM]
[Not Detected]
Set [Enhanced]
when Native OS
(Win2000 / XP)
is used.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
ATA/IDE Configuration
Please select [Compatible] when you install legacy OS (Windows NT). If
native OS (Windows 2000 / XP) is installed, please select [Enhanced].
Then in the option “Configure SATA as”, you are allowed to set the selection
from [AHCI] to [RAID] if you plan to enable RAID function. Configuration
options: [AHCI], [IDE], and [RAID]. The default value is [AHCI].
1. AHCI (Advanced Host Controller Interface) supports Hot
Plug, NCQ and other new features that will improve SATA
disk performance but IDE mode does not have these
advantages.
2. Only AHCI and RAID modes support Hot Plug function.
When [Compatible] is selected
Combined Option
It allows you to select between [SATA0, 1, 2, 3], [IDE1, SATA1, SATA3],
and [SATA0, SATA2, IDE1]. If it is set to [SATA0, SATA2, IDE1], then
SATAII_BLACK (PORT1), SATAII_ORANGE (PORT3) will not work. Likewise,
if it is set to [IDE1, SATA1, SATA3], then SATAII_BLUE (PORT0), SATAII_RED
(PORT2) will not work.
50
Because Intel® ICH7R south bridge only supports four IDE devices
under legacy OS (Windows NT), you have to choose [SATA0, 1, 2, 3],
[IDE1, SATA1, SATA3], and [SATA0, SATA2, IDE1] when the installed
device is used with legacy OS.
Master
[SATA0, 1, 2, 3]
[SATA0, SATA2, IDE1]
[IDE1, SATA1, SATA3]
SATAII_BLUE
SATAII_BLUE
(PORT0)
SATAII_BLACK
(PORT1)
SATAII_RED
(PORT2)
SATAII_ORANGE
(PORT3)
(PORT0),
SATAII_BLACK
(PORT1)
SATAII_RED
(PORT2),
Slave
SATAII_ORANGE
(PORT3)
BIOS SETUP UTILITY
Advanced
Primary IDE Master
Device
Vendor
Size
LBA Mode
Block Mode
PIO Mode
Async DMA
Ultra DMA
S.M.A.R.T.
:Hard Disk
:ST340014A
:40.0 GB
:Supported
:16Sectors
:4
:MultiWord DMA-2
:Ultra DMA-5
:Supported
Type
LBA/Large Mode
Block (Multi-Sector Transfer)
PIO Mode
DMA Mode
S.M.A.R.T.
32Bit Data Transfer
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Disabled]
[Enabled]
Select the type
of device connected
to the system.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
TYPE
Use this item to configure the type of the IDE device that you specify.
Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD].
[Not Installed]: Select [Not Installed] to disable the use of IDE device.
[Auto]: Select [Auto] to automatically detect the hard disk drive.
After selecting the hard disk information into BIOS, use a disk
utility, such as FDISK, to partition and format the new IDE hard
disk drives. This is necessary so that you can write or read
data from the hard disk. Make sure to set the partition of the
Primary IDE hard disk drives to active.
[CD/DVD]: This is used for IDE CD/DVD drives.
[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),
such as MO.
51
LBA/Large Mode
Use this item to select the LBA/Large mode for a hard disk > 512 MB under
DOS and Windows; for Netware and UNIX user, select [Disabled] to
disable the LBA/Large mode.
Block (Multi-Sector Transfer)
The default value of this item is [Auto]. If this feature is enabled, it will
enhance hard disk performance by reading or writing more data during
each transfer.
PIO Mode
Use this item to set the PIO mode to enhance hard disk performance by
optimizing the hard disk timing.
DMA Mode
DMA capability allows the improved transfer-speed and data-integrity for
compatible IDE devices.
S.M.A.R.T.
Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis,
and Reporting Technology) feature. Configuration options: [Disabled], [Auto],
[Enabled].
32-Bit Data Transfer
Use this item to enable 32-bit access to maximize the IDE hard disk data
transfer rate.
3.3.5 PCIPnP Configuration
BIOS SETUP UTILITY
Advanced
Advanced PCI / PnP Settings
WARNING: Setting wrong values in below actions
may cause system to malfunction.
PCI Latency Timer
PCI IDE BusMaster
Value in units of PCI
clocks for PCI device
latency timer
register.
[32]
[Enabled]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
PCI Latency Timer
The default value is 32. It is recommended to keep the default value unless
the installed PCI expansion cards’ specifications require other settings.
PCI IDE BusMaster
Use this item to enable or disable the PCI IDE BusMaster feature.
52
3.3.6 Floppy Configuration
In this section, you may configure the type of your floppy drive.
BIOS SETUP UTILITY
Advanced
Floppy Configuration
[1.44 MB 31 2"]
Floppy A
Select the type of
floppy drive
connected to the
system.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
3.3.7 Super IO Configuration
BIOS SETUP UTILITY
Advanced
Configure Win627EHF Super IO Chipset
OnBoard Floppy Controller
Serial Port Address
Infrared Port Address
Parallel Port Address
Parallel Port Mode
EPP Version
ECP Mode DMA Channel
Parallel Port IRQ
OnBoard Game Port
OnBoard MIDI Port
Allow BIOS to Enable
or Disable Floppy
Controller.
[Enabled]
[3F8 / IRQ4]
[Disabled]
[378]
[ECP + EPP]
[1.9]
[DMA3]
[IRQ7]
[Auto]
[Disabled]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
OnBoard Floppy Controller
Use this item to enable or disable floppy drive controller.
Serial Port Address
Use this item to set the address for the onboard serial port or disable it.
Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4],
[2E8 / IRQ3].
Infrared Port Address
Use this item to set the address for the onboard infrared port or disable it.
Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3].
53
Parallel Port Address
Use this item to set the address for the onboard parallel port or disable it.
Configuration options: [Disabled], [378], and [278].
Parallel Port Mode
Use this item to set the operation mode of the parallel port. The default
value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP
version in the following item, “EPP Version”. Configuration options:
[Normal], [Bi-Directional], and [ECP+EPP].
EPP Version
Use this item to set the EPP version. Configuration options: [1.9]
and [1.7].
ECP Mode DMA Channel
Use this item to set the ECP mode DMA channel. Configuration
options: [DMA0], [DMA1], and [DMA3].
Parallel Port IRQ
Use this item to set the IRQ for the parallel port. Configuration options:
[IRQ5] and [IRQ7].
OnBoard Game Port
Use this item to enable the Game Port or disable it. The default value is
[Auto].
OnBoard MIDI Port
Use this itme to select the address for the MIDI Port or disable it. Configuration options: [Disabled], [300], and [330].
54
3.3.8 USB Configuration
BIOS SETUP UTILITY
Advanced
USB Configuration
To enable or disable
the onboard USB
controllers.
[Enabled]
[Enabled]
[Disabled]
USB Controller
USB 2.0 Support
Legacy USB Support
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
USB Controller
Use this item to enable or disable the use of USB controller.
USB 2.0 Support
Use this item to enable or disable the USB 2.0 support.
Legacy USB Support
Use this item to enable or disable the support to emulate legacy I/O
devices such as mouse, keyboard,... etc. Or you may select [Auto] so
that the system will start to auto-detect; if there is no USB device
connected, “Auto” option will disable the legacy USB support.
3.4 Hardware Health Event Monitoring Screen
In this section, it allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, CPU fan
speed, chassis fan speed, and the critical voltage.
Main
Advanced
BIOS SETUP UTILITY
Boot
H/W Monitor
Hardware Health Event Monitoring
CPU Temperature
M / B Temperature
: 37 C / 98 F
: 31 C / 87 F
CPU Fan Speed
Chassis Fan Speed
: 3400 RPM
: N/A
Vcore
+ 3.30V
+ 5.00V
+ 12.00V
:
:
:
:
CPU Quiet Fan
Target CPU Temperature ( C)
Tolerance ( C)
Target Fan Speed
Security
Target Fan Speed
Fast
Middle
Slow
1.629V
3.306V
5.067V
11.890V
F1
F9
F10
ESC
[Enabled]
[50]
[02]
[Fast]
Select Screen
Select Item
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
55
Exit
CPU Quiet Fan
This item allows you to identify the temperature of CPU fan. If you set this
option as [Disabled], the CPU fan will operate in full speed. If you set this
option as [Enabled], you will find the items “Target CPU Temperature
( C)”, “Tolerance ( C)”, and “Minimun Fan Speed” appear to allow you
adjusting them. The default value is [Disabled]. You are allowed to enable
this function only when you install 4-pin CPU fan.
Target CPU Temperature ( C)
The target temperature will be between 45 C and 65 C. The default
value is [50].
Tolerance ( C)
The default value of tolerance is [2], which means the error of the
target CPU temperature will be within 2 C.
Target Fan Speed
Use this option to set the target fan speed. You can freely adjust the
target fan speed according to the target CPU temperature that you
choose. The default value is [Fast]. Configuration options: [Fast], [Middle]
and [Slow].
3.5 Boot Screen
In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority.
Main
Advanced
BIOS SETUP UTILITY
H/W Monitor
Boot
Boot Settings
Exit
Configure Settings
during System Boot.
Boot Settings Configuration
1st Boot Device
2nd Boot Device
3rd Boot Device
Hard Disk Drives
Removable Drives
CD/DVD Drives
Security
[1st Floppy Device]
[HDD: PM - HDS722580VL]
[CD / DVD: 3S - CD - ROM C]
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
56
3.5.1 Boot Settings Configuration
BIOS SETUP UTILITY
Boot
Boot Settings Configuration
Boot From Onboard LAN
Bootup Num-Lock
To enable or disable the
boot from onboard LAN
feature.
[Disabled]
[On]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
Boot From Onboard LAN
Use this item to enable or disable the Boot From Onboard LAN feature.
Boot Up Num-Lock
If this item is set to [On], it will automatically activate the Numeric Lock
function after boot-up.
3.6 Security Screen
In this section, you may set or change the supervisor/user password for the system.
For the user password, you may also clear it.
Main
Advanced
BIOS SETUP UTILITY
H/W Monitor
Boot
Security Settings
Supervisor Password
User Password
Security
Exit
Install or Change the
password.
: Not Installed
: Not Installed
Change Supervisor Password
Change User Password
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Change
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
57
3.7 Exit Screen
Main
Advanced
BIOS SETUP UTILITY
H/W Monitro
Boot
Exit Options
Security
Exit
Exit system setup
after saving the
changes.
Save Changes and Exit
Discard Changes and Exit
Discard Changes
F10 key can be used
for this operation.
Load Optimal Defaults
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2005, American Megatrends, Inc.
Save Changes and Exit
When you select this option, it will pop-out the following message, “Save
configuration changes and exit setup?” Select [OK] to save the changes
and exit the BIOS SETUP UTILITY.
Discard Changes and Exit
When you select this option, it will pop-out the following message, “Discard changes and exit setup?” Select [OK] to exit the BIOS SETUP UTILITY
without saving any changes.
Discard Changes
When you select this option, it will pop-out the following message, “Discard changes?” Select [OK] to discard all changes.
Load Optimal Defaults
When you select this option, it will pop-out the following message, “Load
optimal defaults?” Select [OK] to load the default values for all the setup
configurations.
58
Chapter 4 Software Suppor
Supportt
4 . 1 Install Operating System
This motherboard supports various Microsoft® Windows® operating systems: 2000 /
XP / XP 64-bit / VistaTM / VistaTM 64-bit. Because motherboard settings and hardware
options vary, use the setup procedures in this chapter for general reference only.
Refer to your OS documentation for more information.
4 . 2 Support CD Information
The Support CD that came with the motherboard contains necessary drivers and
useful utilities that enhance the motherboard features.
4 . 2 . 1 Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu did not appear automatically, locate and double click on the
file “ASSETUP.EXE” from the BIN folder in the Support CD to display the menus.
4 . 2 . 2 Drivers Menu
The Drivers Menu shows the available devices drivers if the system detects
installed devices. Please install the necessary drivers to activate the devices.
4 . 2 . 3 Utilities Menu
The Utilities Menu shows the applications software that the motherboard
supports. Click on a specific item then follow the installation wizard to install it.
4 . 2 . 4 “LGA 775 CPU Installation Live Demo” Program
This motherboard is equipped with Intel LGA 775 socket, which is a new CPU
socket interface that Intel has released. Since it has several tiny pins, whcih
are easily to be damaged by improper handling, ASRock sincerely presents
you a clear installation guide through this “LGA 775 CPU Installation Live Demo”.
We hope you may check this live demo program before you start the installation of LGA 775 CPU in order to reduce the risks of CPU and motherboard
damages caused by any improper handling. To see this Live Demo, you can
run Microsoft® Media Player® to play the file. You may find this Live Demo in the
motherboard’s Support CD through the following path:
..\ Live Demo \ PC DIY \ LGA775INST_English.dat
4.2.5 Contact Information
If you need to contact ASRock or want to know more about ASRock, welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your
dealer for further information.
59
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising