K7VT6 User Manual 1 Version 1.0
K7VT6
User Manual
Version 1.0
Published June 2004
Copyright©2004 ASRock INC. All rights reserved.
1
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in
any language, in any form or by any means, except duplication of documentation by
the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed
as a commitment by ASRock. ASRock assumes no responsibility for any errors or
omissions that may appear in this manual.
With respect to the contents of this manual, ASRock does not provide warranty of
any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the manual or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
ASRock Website: http://www.asrock.com
2
Contents
1. Introduction ....................................................... 4
1.1
1.2
1.3
1.4
Package Contents ................................................................
Specifications ......................................................................
Motherboard Layout ............................................................
ASRock I/O PlusTM ............................................................................................................
4
5
7
8
2. Installation ......................................................... 9
Pre-installation Precautions .........................................................
2.1 CPU Installation ....................................................................
2.2 Installation of CPU Fan and Heatsink ..................................
2.3 Installation of Memory Modules (DIMM) ...............................
2.4 Expansion Slots (PCI and AGP Slots) .................................
2.5 Jumpers Setup ....................................................................
2.6 Onboard Headers and Connectors ....................................
2.7 Serial ATA (SATA) Hard Disks Installation ...........................
2.8 Hot Plug and Hot Swap Functions for SATA HDDs .............
2.9 Making An SATA Driver Diskette ..........................................
9
10
10
11
12
13
15
18
18
19
3. BIOS Setup ......................................................... 20
3.1 BIOS Setup Utility .................................................................
3.1.1 BIOS Menu Bar ..........................................................
3.1.2 Legend Bar ................................................................
3.2 Main Menu ............................................................................
3.3 Advanced, Security, Power, Boot, and Exit Menus ...........
20
20
21
21
23
4. Software Support .............................................. 24
4.1 Install Operating System ......................................................
4.2 Support CD Information ........................................................
4.2.1 Running Support CD ..................................................
4.2.2 Drivers Menu .............................................................
4.2.3 Utilities Menu ..............................................................
4.2.4 ASRock “PC-DIY Live Demo” Program ......................
4.2.5 Contact Information ....................................................
24
24
24
24
24
24
24
Appendix ............................................................... 25
1.
2.
3.
4.
5.
Advanced BIOS Setup Menu ...............................................
Security Setup Menu ...........................................................
Power Setup Menu ..............................................................
Boot Setup Menu .................................................................
Exit Menu ..............................................................................
3
25
30
31
32
33
1. Introduction
Thank you for purchasing ASRock K7VT6 motherboard, a reliable motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent
performance with robust design conforming to ASRock’s commitment to quality and
endurance.
Chapter 1 and 2 of this manual contain introduction of the motherboard and step-bystep installation guide. Chapter 3 and 4 contain basic BIOS setup and support CD
information. More information of advanced BIOS setup can be found in Appendix on
page 25 for advanced users’ reference.
Because the motherboard specifications and the BIOS software might
be updated, the content of this manual will be subject to change
without notice. In case any modifications of this manual occur, the
updated version will be available on ASRock website without further
notice. You may find the latest memory and CPU support lists on
ASRock website as well. ASRock website
1.1
http://www.asrock.com
Package Contents
1 x ASRock K7VT6 Motherboard
(ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm)
1 x ASRock K7VT6 Quick Installation Guide
1 x ASRock K7VT6 Support CD
1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)
1 x 3.5-in Floppy Drive Ribbon Cable
1 x Serial ATA (SATA) Data Cable
1 x Serial ATA (SATA) HDD Power Cable (Optional)
1 x ASRock I/O PlusTM Shield
4
1.2
Specifications
Platform:
CPU:
ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm
Supports Socket A (462 pins) for
AMD AthlonTM / AthlonTM XP / DuronTM processor
Chipsets:
North Bridge:
VIA KT600, FSB@400 MHz
South Bridge:
VIA VT8237, Supports USB 2.0, ATA 133, SATA 1.5Gb/s
Memory:
2 DDR DIMM Slots: DDR1 and DDR2
PC3200 (DDR400) / PC2700 (DDR333) /
PC2100 (DDR266), Max. 2GB
IDE:
IDE1: ATA 133 / Ultra DMA Mode 6
IDE2: ATA 133 / Ultra DMA Mode 6
Supports up to 4 IDE Devices
Serial ATA:
2 SATA Connectors, Support 1.5Gb/s Data Transfer Rate
Floppy Port:
Supports up to 2 Floppy Disk Drives
Audio:
5.1 Channels AC’97 Audio
LAN:
Speed: 802.3u (10/100 Ethernet), Supports Wake-On-LAN
Hardware Monitor: CPU Temperature Sensing
Motherboard Temperature Sensing
CPU Overheat Shutdown to Protect CPU Life
(ASRock U-COP)(see CAUTION 1)
CPU Fan Tachometer
Chassis Fan Tachometer
Voltage Monitoring: +12V, +5V, +3.3V, Vcore
PCI slots:
5 Slots with PCI Specification 2.2
AGP slot:
1 AGP Slot, Supports 1.5V, 8X/4X AGP Card (see CAUTION 2)
USB 2.0:
8 USB 2.0 ports:
include 6 ready-to-use USB 2.0 ports on the rear panel,
plus one on-board header supporting 2 extra USB 2.0 ports
(see CAUTION 3)
ASRock I/O PlusTM: 1 PS/2 Mouse Port, 1 PS/2 Keyboard Port,
1 Serial Port: COM1,
1 Parallel Port (ECP/EPP Support)
6 ready-to-use USB 2.0 Ports,
1 RJ-45 Port,
Audio Jack: Line In / Line Out / Microphone
5
BIOS:
AMI legal BIOS, Supports “Plug and Play”,
ACPI 1.1 Compliance Wake-Up Events,
SMBIOS 2.3.1 Support,
CPU Frequency Stepless Control
(only for advanced users’ reference, see CAUTION 4)
Microsoft® Windows® 98 SE / ME / 2000 / XP Compliant
OS:
CAUTION!
1.
While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the
motherboard functions properly and unplug the power cord, then plug it
back again. To improve heat dissipation, remember to spray thermal
grease between the CPU and the heatsink when you install the PC system.
2.
Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!
It may cause permanent damage!
3.
Power Management for USB 2.0 works fine under Microsoft® Windows®
XP SP1/2000 SP4. It may not work properly under Microsoft® Windows®
98/ME. Please refer to Microsoft® official document at
http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx
4.
Although this motherboard offers stepless control, it is not recommended
to perform over clocking. Frequencies other than the recommended CPU
bus frequencies may cause the instability of the system or damage the
CPU. The CPU host frequency of this motherboard is determined by
jumper-setting. You must adjust “FSB Select Jumpers” according to the
FSB of your AMD CPU before you set the “CPU Host Frequency” configuration as “Manual” in BIOS. See page 13 for the details of “FSB Select
Jumpers” adjustment, and page 25 of “User Manual” in the Support CD for
“CPU Host Frequency” configuration.
6
1.3
Motherboard Layout
1
3 4
2
6
5
17.8cm (7.0 in)
PS2_USB_PWR1
1
PS/2
MOUSE
USB 2.0
T: USB2
B: USB3
USB 2.0
Top:
T: USB0 RJ-45
B: USB1
28
USB 2.0
1
T: USB4
B: USB5
JUSB45
Bottom:
Mic In
7
8
2MB
BIOS
LAN
PHY
IDE2
VIA
KT600
CHIPSET
Top:
Line In
Center:
Line Out
27
IDE1
30.5cm (12.0 in)
1
1
1
ATXPWR1
1
J1
DDR 1 (64/72 bit, 184-pin module)
29
1
FID3
FID2
FID1
FID0
SOCKET 462
SERIAL
PORT
(COM1)
FID4
DDR2 (64/72 bit, 184-pin module)
PARALLEL PORT
CPU_FAN1
PS/2
KEYBOARD
K7VT6
AGP 8X
9
1.5V_AGP1
SUPER
I/O
PCI1
26
25
24
23
1
1
1
DDR400
GAME1
USB2.0
AUDIO1
1
JR1 JL1
PCI3
1
11
VIA
VT8237
SATA
FSB400
CLRCMOS2
22
PCI4
ATA133
5.1CH
AUDIO
CODEC
AUX1 CD1
PCI5
PWR_LED1
1
1
PANEL 1
SPEAKER1
USB67
FLOPPY1
21 20
SATA2
SATA1
1
11
12
13
14
10
PCI2
CMOS
BATTERY
1
2
3
4
5
6
7
8
9
10
FSB_SEL0
FSB_SEL1
FSB_SEL2
1
19
PLED PWRBTN
CHA_FAN1
1
HDLED RST
18 17
PS2_USB_PWR1 Jumper
CPU Fan Connector (CPU_FAN1)
CPU Socket
North Bridge Controller
184-pin DDR DIMM Slots (DDR1- 2)
ATX Power Connector (ATXPWR1)
Secondary IDE Connector (IDE2, Black)
Primary IDE Connector (IDE1, Blue)
AGP Slot (1.5V_AGP1)
FSB Select Jumpers
(FSB_SEL0, FSB_SEL1, FSB_SEL2)
South Bridge Controller
Primary Serial ATA Connector (SATA1)
Secondary Serial ATA Connector (SATA2)
Power LED Connector (PWR_LED1)
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
7
12
13
14
15
16
Chassis Fan Connector (CHA_FAN1)
System Panel Connector (PANEL1)
Chassis Speaker Connector (SPEAKER 1)
USB 2.0 Connector (USB67, Blue)
Floppy Connector (FLOPPY1)
Internal Audio Connector: CD1 (Black)
Internal Audio Connector: AUX1 (White)
Clear CMOS Jumper (CLRCMOS2)
JR1 / JL1 Jumpers
Front Panel Audio Connector (AUDIO1)
PCI Slots (PCI1- 5)
Game Port Connector (GAME1)
Flash Memory
Shared USB 2.0 Header (JUSB45, Blue)
J1 Jumper (FID0, FID1, FID2, FID3, FID4)
1.4
ASRock I/O Plus TM
1
2
3
4
5
11
1
2
3
4
5
6
10
9
8
Parallel Port
RJ-45 Port
Line In (Light Blue)
Line Out (Lime)
Microphone (Pink)
2 x Shared USB 2.0 Port (USB4, USB5)
7
8
9
10
11
8
7
6
2 x USB 2.0 Port (USB0, USB1)
2 x USB 2.0 Port (USB2, USB3)
Serial Port: COM1
PS/2 Keyboard Port (Purple)
PS/2 Mouse Port (Green)
2. Installation
K7VT6 is an ATX form factor (12.0-in x 7.0-in, 30.5 cm x 17.8 cm) motherboard.
Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
Before you install or remove any component, ensure that the
power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
1.
2.
3.
4.
5.
Unplug the power cord from the wall socket before touching any
component.
To avoid damaging the motherboard components due to static
electricity, NEVER place your motherboard directly on the carpet or
the like. Also remember to use a grounded wrist strap or touch a
safety grounded object before you handle components.
Hold components by the edges and do not touch the ICs.
Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.
When placing screws into the screw holes to secure the motherboard
to the chassis, please do not over-tighten the screws! Doing so may
damage the motherboard.
9
2.1
Step 1.
Step 2.
Step 3.
CPU Installation
o
Unlock the socket by lifting the lever up to a 90 angle.
Position the CPU directly above the socket such that its marked corner
matches the base of the socket lever.
Carefully insert the CPU into the socket until it fits in place.
The CPU fits only in one correct orientation. DO NOT force the
CPU into the socket to avoid bending of the pins.
Step 4.
When the CPU is in place, press it firmly on the socket while you push
down the socket lever to secure the CPU. The lever clicks on the side tab
to indicate that it is locked.
Step 1
2.2
Step 2, 3
Step 4
Installation of CPU Fan and Heatsink
AMD AthlonTM / AthlonTM XP/ DuronTM family CPUs with a speed of 600 MHz and
higher require larger heatsink and cooling fan. Thermal grease between the
CPU and the heatsink is also needed to improve heat transfer. Make sure that
the CPU and the heatsink are securely fastened and in good contact with
each other. Then connect the CPU fan to the CPU FAN connector (CPU_FAN1,
see page 7, No. 2). For proper installation, please kindly refer to the instruction manuals of the CPU fan and heatsink vendors.
10
2.3
Installation of Memory Modules (DIMM)
K7VT6 motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots.
Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.
Step 1.
Step 2.
Unlock a DIMM slot by pressing the retaining clips outward.
Align a DIMM on the slot such that the notch on the DIMM matches the break
on the slot.
notch
break
notch
break
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into
the slot at incorrect orientation.
Step 3.
Firmly insert the DIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.
11
2.4
Expansion Slots (PCI and AGP Slots)
There are 5 PCI slots and 1 AGP slot on K7VT6 motherboard.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot has
a special design of clasp that can securely fasten the inserted graphics
card.
Please do NOT use a 3.3V AGP card on the AGP slot of this motherboard!
It may cause permanent damage! For the voltage information of your
graphics card, please check with the graphics card vendors.
Installing an expansion card
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Step 6.
Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Remove the system unit cover (if your motherboard is already installed
in a chassis).
Remove the bracket facing the slot that you intend to use.
Keep the screws for later use.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Fasten the card to the chassis with screws.
Replace the system cover.
12
2.5
Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on the pins, the jumper is “Open”.
The illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap
is placed on these 2 pins.
Jumper
Setting
FSB Select Jumpers
(FSB_SEL0,
FSB_SEL1,
FSB_SEL2)
(see p.7 item 10)
1_2
FSB_SEL0
2_3
FSB_SEL1
OPEN
FSB_SEL1
1_2
1_2
FSB_SEL2
FSB_SEL2
FSB 266MHz
FSB 200MHz
FSB_SEL0
FSB_SEL0
OPEN
FSB_SEL1
OPEN
2_3
OPEN
FSB_SEL0
1_2
FSB_SEL1
2_3
1_2
FSB_SEL2
FSB 333MHz
FSB_SEL2
FSB 400MHz
Note: The CPU FSB frequency of this motherboard is determined by jumper-setting. You must
adjust “FSB Select Jumpers” according to the FSB of your AMD CPU. Please follow the
figures above to set the CPU FSB frequency.
PS2_USB_PWR1
(see p.7 item 1)
1_2
2_3
+5V
+5VSB
Short pin2, pin3 to enable
+5VSB (standby) for PS/2 or
USB wake up events.
Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power
supply.
JR1 / JL1 Jumpers
(see p.7 item 23)
JR1
JL1
Note: If JR1 and JL1 Jumpers are short, both the front panel and the rear panel audio
connectors can work.
Clear CMOS Jumper
(CLRCMOS2)
(see p.7 item 22)
2-pin jumper
Note: CLRCMOS2 allows you to clear the data in CMOS. The data in CMOS includes system
setup information such as system password, date, time, and system setup parameters. To
clear and reset the system parameters to default setup, please turn off the computer and
unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper
cap to short the Clear CMOS jumper for 5 seconds. After shorting the Clear CMOS jumper,
please remove the jumper cap. However, please do not clear the CMOS right after you
update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS,
you must boot up the system first, and then shut it down before you do the clear-CMOS
action.
13
J1 Jumper
(FID0, FID1, FID2, FID3, FID4)
(see p.7 item 29)
FID4
1
FID3
1
FID2
1
FID1
1
FID0
1
Note: The set of J1 jumper is only for advanced users to adjust the multiplier of CPU. Please
follow the table below to adjust the multiplier of CPU. However, the system will work well
without the adjustment of multiplier. You do not have to adjust the multiplier for normal
usage.
Multiplier
FID0
FID1
FID2
FID3
FID4
5x
5.5x
2-3
1-2
2-3
2-3
1-2
1-2
2-3
2-3
2-3
2-3
6x
6.5x
2-3
1-2
1-2
1-2
1-2
1-2
2-3
2-3
2-3
2-3
7x
7.5x
2-3
1-2
2-3
2-3
2-3
2-3
1-2
1-2
2-3
2-3
8x
8.5x
2-3
1-2
1-2
1-2
2-3
2-3
1-2
1-2
2-3
2-3
9x
9.5x
2-3
1-2
2-3
2-3
1-2
1-2
1-2
1-2
2-3
2-3
10x
10.5x
2-3
1-2
1-2
1-2
1-2
1-2
1-2
1-2
2-3
2-3
11x
11.5x
2-3
1-2
2-3
2-3
2-3
2-3
2-3
2-3
2-3
2-3
12x
12.5x
2-3
1-2
1-2
1-2
2-3
2-3
2-3
2-3
2-3
2-3
13x
13.5x
2-3
1-2
2-3
2-3
1-2
1-2
2-3
2-3
1-2
1-2
14x
15x
2-3
2-3
1-2
2-3
1-2
2-3
2-3
1-2
1-2
1-2
16x
16.5x
2-3
1-2
1-2
1-2
2-3
2-3
1-2
1-2
1-2
1-2
17x
18x
2-3
1-2
2-3
2-3
1-2
1-2
1-2
1-2
1-2
1-2
19x
20x
1-2
1-2
2-3
1-2
2-3
2-3
2-3
2-3
1-2
1-2
21x
22x
1-2
1-2
1-2
2-3
1-2
2-3
2-3
1-2
1-2
1-2
23x
2-3
1-2
1-2
1-2
1-2
24x
1-2
1-2
1-2
1-2
1-2
For example, “Athlon XP 2000+” is an 1666MHz CPU: 12.5 (Multiplier) X 133MHz (External frequency) = 1666MHz
J1 jumper setting:
FID4
1
FID3
1
FID2
1
FID1
1
FID0
1
The jumper caps are not provided by ASRock. Please understand that ASRock
does not guarantee and support the adjustment of multiplier. These jumpers
setting may not apply to all multiplier-locked or even some unlocked AMD
CPU. Frequencies other than the recommended CPU bus frequencies may
cause the instability of the system or damage the CPU.
14
2.6
Connectors
Connectors are NOT jumpers. DO NOT place jumper caps over these
connectors. Placing jumper caps over the connectors will cause permanent damage of the motherboard!
FDD Connector
(33-pin FLOPPY1)
Pin1
(see p.7 item 19)
FLOPPY1
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE Connector (Blue)
Secondary IDE Connector (Black)
(39-pin IDE1, see p.7 item 8)
(39-pin IDE2, see p.7 item 7)
PIN1
IDE1
PIN1
IDE2
connect the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductor, ATA 66/100/133 cable
Note: If you use only one IDE device on this motherboard, please set the IDE
device as “Master”. Please refer to the instruction of your IDE device vendor
for the details. Besides, to optimize compatibility and performance, please
connect your hard disk drive to the primary IDE connector (IDE1, blue) and
CD-ROM to the secondary IDE connector (IDE2, black).
Serial ATA Connectors
(SATA1: see p.7 item 12)
SATA1
SATA2
(SATA2: see p.7 item 13)
Serial ATA (SATA)
Data Cable
These two Serial ATA (SATA)
connectors support SATA data
cables for internal storage
devices. The current SATA
interface allows up to 1.5 Gb/s
data transfer rate.
Either end of the SATA data
cable can be connected to the
SATA hard disk or the SATA
connector on the motherboard.
15
Serial ATA (SATA)
Power Cable
(Optional)
Please connect the black end of
SATA power cable to the power
connect to the SATA HDD
power connector
connect to the
power supply
USB_PWR
P-7
P+7
GND
DUMMY
USB 2.0 Header
(9-pin USB67)
(see p.7 item 18)
1
GND
P+6
P-6
USB_PWR
Shared USB 2.0 Header
(9-pin JUSB45)
(see p.7 item 28)
1
USB_PWR
P-4
P+4
GND
USB_PWR
P-5
P+5
GND
DUMMY
Internal Audio Connectors
(4-pin CD1, 4-pin AUX1)
AUX-R
GND
GND
AUX-L
(CD1: see p.7 item 20)
CD-R
GND
GND
CD-L
AUX1
CD1
(AUX1: see p.7 item 21)
Front Panel Audio Connector
GND
+5VA
BACKOUT-R
BACKOUT-L
(9-pin AUDIO1)
(see p.7 item 24)
1
AUD-OUT-L
DUMMY
AUD-OUT-R
MIC-POWER
MIC
16
connector on the drive. Then
connect the white end of SATA
power cable to the power
connector of the power supply.
ASRock I/O PlusTM provides you
6 ready-to-use USB 2.0 ports on
the rear panel. If the rear USB
ports are not sufficient, this
USB 2.0 header is available to
support 2 extra USB 2.0 ports.
This USB45 connector is shared
with the USB 2.0 ports 4,5 on
ASRock I/O PlusTM. When using
the front panel USB ports by
attaching the front panel USB
cable to this connector
(JUSB45), the USB ports 4,5 on
ASRock I/O PlusTM will not be able
to function.
These connectors allow you to
receive stereo audio input from
sound sources such as a CDROM, DVD-ROM, TV tuner card,
or MPEG card.
This is an interface for front panel
audio cable that allows convenient connection and control of
audio devices.
System Panel Connector
PLED+
PLEDPWRBTN#
GND
(9-pin PANEL1)
This connector accommodates
several system front panel
functions.
(see p.7 item 16)
1
DUMMY
RESET#
GND
HDLEDHDLED+
Chassis Speaker Connector
1
SPEAKER
DUMMY
DUMMY
+5V
(4-pin SPEAKER 1)
(see p.7 item 17)
Chassis Fan Connector
GND
+12V
CHA_FAN_SPEED
(3-pin CHA_FAN1)
(see p.7 item 15)
CPU Fan Connector
CPU_FAN_SPEED
+12V
GND
(3-pin CPU_FAN1)
(see p.7 item 2)
ATX Power Connector
Please connect the chassis
speaker to this connector.
Please connect a chassis fan
cable to this connector and
match the black wire to the
ground pin.
Please connect a CPU fan cable
to this connector and match
the black wire to the ground pin.
Please connect an ATX power
supply to this connector.
(20-pin ATXPWR1)
(see p.7 item 6)
Power LED Connector
1
PLEDPLED+
PLED+
(3-pin PWR_LED1)
(see p.7 item 14)
+5V
JBB1
JBX
MIDI_OUT
J2Y
JBY
MIDI_IN
Game Connector
(15-pin GAME1)
(see p.7 item 26)
1
+5V
JAB2
JAY
GND
GND
JAX
JAB1
+5V
17
Please connect a 3-pin power
LED cable to this connector.
Connect a Game cable to this
connector if the Game port
bracket is installed.
2.7
Serial ATA (SATA) Hard Disks Installation
This motherboard adopts VIA VT8237 southbridge chipset that supports Serial
ATA (SATA) hard disks and RAID functions. You may install SATA hard disks on
this motherboard for internal storage devices. This section will guide you to install
the SATA hard disks.
STEP 1: Install the SATA hard disks into the drive bays of your chassis.
STEP 2: Connect the SATA power cable to the SATA hard disk.
STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA
connector.
STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.
2.8
Hot Plug and Hot Swap Functions for SATA HDDs
K7VT6 motherboard supports Hot Plug and Hot Swap functions for SATA Devices.
What is Hot Plug Function?
If the SATA HDDs are NOT set for RAID configuration, it is called “Hot
Plug” for the action to insert and remove the SATA HDDs while the
system is still power-on and in working condition. However, please note
that it cannot perform Hot Plug if the OS has been installed into the SATA
HDD.
What is Hot Swap Function?
If SATA HDDs are built as RAID1 then it is called “Hot Swap” for the
action to insert and remove the SATA HDDs while the system is still
power-on and in working condition.
18
2.9
Making An SATA Driver Diskette
If you want to install Windows 2000 or Windows XP on your SATA HDDs, you will
need to make an SATA driver diskette before you start the OS installation.
STEP 1: Insert the ASRock Support CD into your optical drive to boot your system.
(Do NOT insert any floppy diskette into the floppy drive at this moment!)
STEP 2: During POST at the beginning of system boot-up, press <F11> key, and
then a window for boot devices selection appears. Please select CDROM as the boot device.
STEP 3: When you see the message on the screen, “Do you want to generate
Serial ATA driver diskette [YN]?”, press <Y>.
STEP 4: Then you will see these messages,
Please insert a diskette into the floppy drive.
WARNING! Formatting the floppy diskette will
lose ALL data in it!
Start to format and copy files [YN]?
Please insert a floppy diskette into the floppy drive, and press <Y>.
STEP 5: The system will start to format the floppy diskette and copy SATA drivers
into the floppy diskette.
Once you have the SATA driver diskette ready, you may start to install Windows 2000 /
Windows XP on your system directly without setting the RAID configuration on your
system, or you may start to use “VT8237 SATA RAID BIOS” to set RAID 0 / RAID 1 / JBOD
configuration before you install the OS. Before you start to configure the RAID function,
you need to check the installation guide in the Support CD for proper configuration. Please
refer to the document in the Support CD, “Guide to SATA Hard Disks Installation and RAID
Configuration”, which is located in the folder at the following path:
.. \ SATA RAID BIOS
You may also set the RAID configuration by using “VIA RAID Tool” in Windows environment.
Please refer to the document in the Support CD, “Guide to VIA RAID Tool”, which is located
in the folder at the following path:
.. \ VIA RAID Tool
19
3. BIOS Setup
3.1 BIOS Setup Utility
This section explains how to use the BIOS Setup Utility to configure your system.
The Flash Memory on the motherboard stores the BIOS Setup Utility. You may run the
BIOS Setup when you start up the computer. Please press <F2> during the PowerOn-Self-Test (POST) to enter the BIOS Setup Utility, otherwise, POST will continue
with its test routines.
If you wish to enter the BIOS Setup after POST, restart the system by pressing
<Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis.
You may also restart the system by turning the system off and then back on.
The BIOS Setup Utility is designed to be user-friendly. It is a menu-driven program,
which allows you to scroll through its various sub-menus and select among the
predetermined choices.
Because the BIOS software is constantly being updated, the
following BIOS setup screens and descriptions are for reference
purpose only, and may not exactly match what you see on your
screen.
3.1.1 BIOS Menu Bar
The top of the screen has a menu bar with the following selections:
MAIN
Sets up the basic system configuration
ADVANCED
Sets up the advanced features
SECURITY
Sets up the security features
POWER
Configures Power Management features
BOOT
Configures the default system device that is used
to locate and load the Operating System
EXIT
Exits the current menu or the BIOS Setup
To access the menu bar items, press the right or left arrow key on the keyboard
until the desired item is highlighted.
3.1.2 Legend Bar
At the bottom of the Setup Screen is a legend bar. The following table lists the keys
in the legend bar with their corresponding functions.
20
Navigation Key(s)
<F1>
<ESC>
/
/
+ / <Enter>
<F9>
<F10>
Function Description
Displays the General Help Screen
Jumps to the Exit menu or returns to the upper menu
from the current menu
Moves cursor up or down between fields
Selects menu to the left or right
Increases or decreases values
Brings up a selected menu for a highlighted field
Loads all the setup items to default value
Saves changes and exits Setup
3.2 Main Menu
When you enter the BIOS Setup Utility, the following screen appears.
Main
Advanced
AMIBIOS SETUP UTILITY - VERSION 3.31a
Boot
Power
Exit
Security
[
System Date
System Time
Oct 31 2003 Fri
20:07:40
Floppy Drives
IDE Devices
BIOS Version
Processor Type
Processor Speed
L1 Cache Size
L2 Cache Size
Total Memory
DDR1
DDR2
F1:Help
Esc:Exit
Setup Help
]
Month: Jan - Dec
Day: 01 - 31
Year: 1980 - 2099
K7VT6 BIOS P1.00
AMD Athlon(tm) XP 2600+
2133 MHz
128 KB
256 KB
512 MB
512 MB / 200 MHz (DDR400)
None
:Select Item
:Select Menu
+/-:Change Values
Enter:Select Sub-Menu
F9:Setup Defaults
F10:Save & Exit
System Date [Month/Day/Year]
Set the system date that you specify. Valid values for month, day, and year are
Month: (Jan to Dec), Day: (1 to 31), Year: (up to 2099). Use
keys to move
between the Month, Day, and Year fields.
System Time [Hour:Minute:Second]
Set the system to the time that you specify. Use
keys to move between
the Hour, Minute, and Second fields.
Floppy Drives
Use this to set the type of floppy drives installed.
IDE Devices
Use this to configure IDE devices.
21
TYPE
To set the type of the IDE device, first, please select “IDE Devices” on Main
menu and press <Enter> to get into the sub-menu. Then, select among
“Primary IDE Master”, “Primary IDE Slave”, “Secondary IDE Master”, and
“Secondary IDE Slave” to make configuration of its type. Below are the
configuration options.
AMIBIOS SETUP UTILITY - VERSION 3.31a
Main
Primary IDE Master
Type
Cylinders
Heads
Write Precompensation
Sectors
Maximum Capacity
LBA Mode
Block Mode
Fast Programmed I/O Modes
32 Bit Transfer Mode
Ultra DMA Mode
F1:Help
Esc:Previous Menu
:Select Item
[
Auto
Setup Help
]
Select how to set the
parameters of drive,
Or
Select [AUTO] to set
all HDD parameters
automatically.
Off
Off
Auto
Off
Auto
+/-:Change Values
Enter:Select Sub-Menu
F9:Setup Defaults
F10:Save & Exit
[USER]: It allows user to manually enter the number of cylinders, heads,
and sectors per track for the drive.
Before attempting to configure a hard disk drive, make sure you
have the correct configuration information supplied by the drive
manufacturer. Incorrect settings may cause the system to fail
to recognize the installed hard disk.
[Auto]: Select [Auto] to automatically detect hard disk drive. If autodetection is successful, the BIOS Setup automatically fills in the
correct values for the remaining fields on this sub-menu. If the autodetection fails, it may due to that the hard disk is too old or too new.
If the hard disk was already formatted on an older system, the BIOS
Setup may detect incorrect parameters. In these cases, select [User]
to manually enter the IDE hard disk drive parameters.
After entering the hard disk information into BIOS, use a disk utility,
such as FDISK, to partition and format the new IDE hard disk
drives. This is necessary so that you can write the data into or
read the data from the installed hard disk. Please make sure to set
the partition of the Primary IDE hard disk drives to make them
active.
22
[CD/DVD]: This is used for IDE CD/DVD drives.
[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),
such as MO.
Cylinders
This is used to configure the number of cylinders. Refer to the drive
documentation to determine the correct value.
Heads
This is used to configure the number of read/write heads. Refer to the
drive documentation to determine the correct values.
Write Pre-compensation
Enter Write Pre-compensation sector. Refer to the drive documentation to
determine the correct value.
Sectors
This is used to configure the number of sectors per track. Refer to the
drive documentation to determine the correct value.
Maximum Capacity
This field shows the drive’s maximum capacity as calculated by the BIOS
based on the drive information you entered.
LBA Mode
This allows user to select the LBA mode for a hard disk > 512 MB under
DOS and Windows; for Netware and UNIX user, select [Off] to disable the
LBA mode.
Block Mode
Set the block mode to [On] will enhance hard disk performance by reading
or writing more data during each transfer.
Fast Programmed I/O Modes
This allows user to set the PIO mode to enhance hard disk performance by
optimizing the hard disk timing.
32 Bit Transfer Mode
It allows user to enable 32-bit access to maximize the IDE hard disk data
transfer rate.
Ultra DMA Mode
Ultra DMA capability allows improved transfer speeds and data integrity
for compatible IDE devices. Set to [Disabled] to suppress Ultra DMA
capability.
3.3 Advanced, Security, Power, Boot, and Exit Menus
Detailed descriptions of these menus are listed in the Appendix. See page 25.
23
4. Software Support
4.1 Install Operating System
This motherboard supports various Microsoft® Windows® operating systems:
98 SE / ME / 2000 / XP. Because motherboard settings and hardware options vary,
use the setup procedures in this chapter for general reference only. Refer to your
OS documentation for more information.
4.2 Support CD Information
The Support CD that came with the motherboard contains necessary drivers and
useful utilities that will enhance the motherboard features.
4.2.1 Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu did not appear automatically, locate and double click on the file
ASSETUP.EXE from the BIN folder in the Support CD to display the menus.
4.2.2 Drivers Menu
The Drivers Menu shows the available devices drivers if the system detects
installed devices. Install the necessary drivers to activate the devices.
4.2.3 Utilities Menu
The Utilities Menu shows the applications software that the motherboard
supports. Click on a specific item then follow the installation wizard to install it.
4.2.4 ASRock PC-DIY Live Demo Program
ASRock presents you a multimedia PC-DIY live demo, which shows you how to
install your own PC system step by step. You may find the file through the
following path:
..\ MPEGAV \ AVSEQ01.DAT
To see this demo program, you may run Microsoft® Media Player® to play the file.
4.2.5 Contact Information
If you need to contact ASRock or want to know more about ASRock, welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your
dealer for further information.
24
Appendix: Advanced BIOS Setup
This section will introduce you the following BIOS Setup menus: “Advanced,”
“Security,” “Power,” “Boot,” and “Exit.”
1. Advanced BIOS Setup Menu
Main
Advanced
AMIBIOS SETUP UTILITY - VERSION 3.31a
Boot
Power
Exit
Security
[
Spread Spectrum
CPU Host Frequency
Actual Frequency
DRAM Frequency
Flexibility Option
Disabled
Auto
133MHz
Auto
Disabled
Setup Help
]
<Enter> to enable or
disable the feature of
spread spectrum.
Chipset Configuration
Resource Configuration
Peripheral Configuration
System Hardware Monitor
F1:Help
Esc:Exit
:Select Item
:Select Menu
+/-:Change Values
Enter:Select Sub-Menu
F9:Setup Defaults
F10:Save & Exit
Spread Spectrum
This field should always be [Disabled] for better system stability.
CPU Host Frequency
[Auto]
It is recommended to select this option, which will let the CPU host frequency of
this motherboard determined by the jumper-setting.
[Manual]
This allows user to set CPU host frequency manually. However, because the
CPU host frequency of this motherboard is determined by the jumper-setting,
you must set the FSB jumper adjustment according to your AMD CPU before you
use this “Manual” option as the FSB setting in BIOS setup to perform over
clocking. This is not recommended unless you thoroughly know the feature.
Wrong setup may cause problems during operation.
DRAM Frequency
If set to [Auto], the motherboard will detect the inserted memory module(s) and
automatically assign appropriate frequency. You may select other value as
operating frequency: [133MHz (DDR266)], [166MHz (DDR333)],
[200MHz (DDR400)].
Flexibility Option
The default value of this option is [Disabled]. It will allow better tolerance for
memory compatibility when it is set to [Enabled].
25
Chipset Configuration
AMIBIOS SETUP UTILITY - VERSION 3.31a
Advanced
Chipset Configuration
[ Setup Help ]
AGP Mode
AGP Aperture Size
AGP Fast Write
PCI Delay Transaction
Auto
64MB
Disabled
Disabled
USB Controller
USB Device Legacy Support
Enabled
Disabled
DRAM CAS# Latency
Auto
V-Link Speed
Over Vcore Voltage
VCCM Voltage
AGP Voltage
Normal
Disabled
Auto
Auto
F1:Help
Esc:Previous Menu
:Select Item
+/-:Change Values
Enter:Select Sub-Menu
<Enter> to select [4X],
[2X], [1X] as the AGP
mode.
F9:Setup Defaults
F10:Save & Exit
AGP Mode
This feature will be set to [Auto] as default.
AGP Aperture Size
It refers to a section of the PCI memory address range used for graphics
memory. It is recommended to leave this field at the default value unless the
installed AGP card’s specification requires other sizes.
AGP Fast Write
This allows you to enable or disable the feature of AGP fast write protocol
support.
PCI Delay Transaction
Enable PCI Delay Transaction feature will free the PCI Bus when the CPU is
accessing 8-bit ISA cards. Disable this feature when using ISA cards that are
not PCI 2.1 compliant.
USB Controller
Use this to enable or disable the use of USB controller.
USB Device Legacy Support
Use this to enable or disable the support to emulate legacy I/O devices such as
mouse, keyboard,... etc.
DRAM CAS# Latency
This is used to adjust the means of memory accessing. Configuration options:
[Auto], [2T], [2.5T], [3T]. It is recommended to leave this field as [Auto] unless the
installed DRAM’s specification requires other value.
V-Link Speed
This feature allows you to speed up the V-Link speed. The default value is
[Normal].
26
Over Vcore Voltage
This feature allows you to increase the CPU Vcore voltage with two levels. The
default value is [Disabled].
It is not recommended to enable “Over Vcore Voltage” feature. Doing so
may cause CPU damage.
VCCM Voltage
This item allows you to adjust DRAM voltage. Configuration options: [Auto],
[High], and [Low]. The default value is [Auto].
AGP Voltage
This item allows you to adjust AGP voltage. Configuration options: [Auto], [High],
and [Low]. The default value is [Auto].
Resource Configuration
AMIBIOS SETUP UTILITY - VERSION 3.31a
Advanced
Resource Configuration
PCI Latency Timer (PCI Clocks)
Primary Graphics Adapter
F1:Help
Esc:Previous Menu
:Select Item
[
Setup Help
]
<Enter> to select PCI
clocks. Leave on
default setting for the
best PCI performance.
32
PCI
+/-:Change Values
Enter:Select Sub-Menu
F9:Setup Defaults
F10:Save & Exit
PCI Latency Timer (PCI Clocks)
The default is 32. It is recommended to keep the default value unless the installed PCI expansion cards’ specifications require other settings.
Primary Graphics Adapter
Select PCI or AGP as the primary graphics adapter if both PCI VGA and AGP card
are installed.
27
Peripheral Configuration
AMIBIOS SETUP UTILITY - VERSION 3.31a
Advanced
Peripheral Configuration
OnBoard FDC
OnBoard Serial Port
OnBoard Parallel Port
Parallel Port Mode
EPP Version
Parallel Port IRQ
Parallel Port DMA Channel
OnBoard Midi Port
Midi IRQ Select
OnBoard Game Port
OnBoard IDE
OnBoard LAN
OnBoard AC' 97 Audio
F1:Help
Esc:Previous Menu
:Select Item
[ Setup Help ]
Auto
Auto
Auto
ECP+EPP
1.9
Auto
Auto
Disabled
5
200h
Enabled
Enabled
Auto
+/-:Change Values
Enter:Select Sub-Menu
<Enter> to enable or
disable the floppy
drive controller.
F9:Setup Defaults
F10:Save & Exit
OnBoard FDC
Use this to enable or disable floppy drive controller.
OnBoard Serial Port
Use this to set addresses for the onboard serial ports or disable serial ports.
Configuration options: [Auto], [Disabled], [3F8 / IRQ4 / COM1],
[2F8 / IRQ3 / COM2], [3E8 / IRQ4 / COM3], [2E8 / IRQ3 / COM4].
OnBoard Parallel Port
Select Parallel Port address or disable Parallel Port. Configuration options: [Auto],
[Disabled], [378], [278].
Parallel Port Mode
Set the operation mode of the parallel port. The default value is [ECP+EPP]. If
this option is set to [ECP+EPP], it will show the EPP version in the following
item, “EPP Version”.
OnBoard Midi Port
Select address for Midi Port or disable Midi Port. Configuration options: [Disabled],
[330], [300], [290], [292].
Midi IRQ Select
Use this to select Midi IRQ. Configuration options: [3], [4], [5], [7], [10], [11].
OnBoard Game Port
Select address for Game Port or disable Game Port. Configuration options:
[Disabled], [200h], [208h].
OnBoard IDE
This allows you to enable or disable the onboard IDE controller.
28
OnBoard LAN
This allows you to enable or disable the onboard LAN feature.
OnBoard AC’97 Audio
Select [Disabled], [Auto] or [Enabled] for the onboard AC’97 Audio feature.
System Hardware Monitor
You may check the status of the hardware on your system. It allows you to
monitor the parameters for CPU temperature, Motherboard temperature, CPU
fan speed, and critical voltage.
AMIBIOS SETUP UTILITY - VERSION 3.31a
Advanced
System Hardware Monitor
CPU Temperature
M / B Temperature
CPU FAN Speed
Chassis FAN Speed
Vcore
+ 3.30V
+ 5.00V
+ 12.00V
F1:Help
Esc:Previous Menu
[
Setup Help
35 C / 95 F
27 C / 82 F
3110 RPM
0 RPM
1.72 V
3.31 V
4.97 V
12.16 V
:Select Item
+/-:Change Values
Enter:Select Sub-Menu
29
F9:Setup Defaults
F10:Save & Exit
]
2. Security Setup Menu
Main
AMIBIOS SETUP UTILITY - VERSION 3.31a
Boot
Power
Exit
Security
Advanced
[
Supervisor Password
User Password
Clear
Clear
Set Supervisor Password
Set User Password
[ Enter ]
[ Enter ]
Password Check
Setup
F1:Help
Esc:Exit
:Select Item
:Select Menu
Setup Help
]
<Enter> to set the
supervisor password.
+/-:Change Values
Enter:Select Sub-Menu
F9:Setup Defaults
F10:Save & Exit
Supervisor Password: This field shows the status of the Supervisor Password.
[Clear]: No password has been set.
[Set]: Supervisor password has been set.
User Password: This field shows the status of the User Password.
[Clear]: No password has been set.
[Set]: User password has been set.
Set Supervisor Password: Press <Enter> to set the Supervisor Password. Valid
password can be a 1 to 6 alphanumeric characters combination. If you already
have a password, you need to enter your current password first in order to
create a new password.
Set User Password: Press <Enter> to set the User Password. Valid password can
be a 1 to 6 alphanumeric characters combination. If you already have a
password, you need to enter your current password first in order to create a
new password.
Password Check: Select the check point for “Password Check”. Configuration
options: [Setup], [Always]. If [Setup] option is selected, the “Password Check”
is performed before BIOS setup. If [Always] option is selected, the “Password
Check” is performed before both boot-up and BIOS setup.
30
3. Power Setup Menu
Main
Advanced
AMIBIOS SETUP UTILITY - VERSION 3.31a
Boot
Power
Exit
Security
[ Setup Help ]
Suspend To RAM
Repost Video on STR Resume
Restore on AC / Power Loss
Ring-In Power On
PCI Devices Power On
PS / 2 Keyboard Power On
RTC Alarm Power On
RTC Alarm Date
RTC Alarm Hour
RTC Alarm Minute
RTC Alarm Second
F1:Help
Esc:Exit
:Select Item
:Select Menu
Disabled
Disabled
Power Off
Disabled
Disabled
Disabled
Disabled
Every Day
12
30
30
+/-:Change Values
Enter:Select Sub-Menu
<Enter> to select
auto-detect or disable
the Suspend-to-RAM
feature.
F9:Setup Defaults
F10:Save & Exit
Suspend to RAM
This field allows you to select whether to auto-detect or disable the Suspendto-RAM feature. Select [Auto] will enable this feature if the system supports it.
Repost Video on STR Resume
This feature allows you to repost video on STR resume. It is recommended to
enable this feature under Microsoft® Windows® 98 / ME.
Restore on AC/Power Loss
This allows you to set the power state after an unexpected AC/power loss. If
[Power Off] is selected, the AC/power remains off when the power recovers.
If [Power On] is selected, the AC/power resumes and the system starts to boot
up when the power recovers.
Ring-In Power On
Use this to enable or disable Ring-in signals to turn on the system from the
power-soft-off mode.
PCI Devices Power On
Use this to enable or disable PCI devices to turn on the system from the powersoft-off mode.
PS/2 Keyboard Power On
Use this to enable or disable PS/2 keyboard to turn on the system from the
power-soft-off mode.
RTC Alarm Power On
Use this to enable or disable RTC (Real Time Clock) to power on the system. If
[Enable] is selected, you must fill the RTC Alarm Date / Hour / Minute / Second
sub-fields with the actual wake up time you desire.
31
4. Boot Setup Menu
Main
Advanced
AMIBIOS SETUP UTILITY - VERSION 3.31a
Boot
Power
Exit
Security
[ Setup Help ]
Quick Boot Mode
Boot Up Num-Lock
Boot To OS/2
Boot From Network
VIA SATA Raid Utility
Enabled
On
No
Disabled
Enabled
<Enter> to enable or
disable the quick boot
mode.
Boot Device Priority
F1:Help
Esc:Exit
:Select Item
:Select Menu
+/-:Change Values
Enter:Select Sub-Menu
F9:Setup Defaults
F10:Save & Exit
Quick Boot Mode
Enable this mode will speed up the boot-up routine by skipping memory retestings.
Boot Up Num-Lock
If this is enabled, it will automatically activate the Numeric Lock function after
boot-up.
Boot To OS/2
This enables boot-up to OS/2 operating system.
Boot From Network
Use this to enable or disable “boot from network” feature.
VIA SATA Raid Utility
Use this to enable or disable VIA VT8237 SATA Raid BIOS Utility during POST.
Boot Device Priority
This allows you to set the boot device priority.
32
5. Exit Menu
Main
Advanced
AMIBIOS SETUP UTILITY - VERSION 3.31a
Boot
Power
Exit
Security
Exit Saving Changes
Exit Discarding Changes
Load Default Settings
Discard Changes
F1:Help
Esc:Exit
[
[
[
[
Enter
Enter
Enter
Enter
:Select Item
:Select Menu
[
]
]
]
]
Setup Help
]
Exits and saves the
changes in CMOS RAM.
+/-:Change Values
Enter:Select Sub-Menu
F9:Setup Defaults
F10:Save & Exit
Exit Saving Changes
After you enter the sub-menu, the message “Save current settings and exit” will
appear. If you press <ENTER>, it will save the current settings and exit the BIOS
SETUP Utility.
Exit Discarding Changes
After you enter the submenu, the message “Quit without saving changes” will
appear. If you press <ENTER>, you will exit the BIOS Setup Utility without making
any changes to the settings.
Load Default Settings
After you enter the submenu, the message “Load default settings” will appear.
If you press <Enter>, it will load the default values for all the setup configuration.
Discard Changes
After you enter the sub-menu, the message “Load setup original values” will
appear. If you press <ENTER>, original values will be restored and all changes
are discarded.
33
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising