Best Power B510-0900A Service manual
MOHAWK
INSTALLATION & OPERATION MANUAL
MP-18-24VDC-SERIES
ELECTRIC/HYDRAULIC
PORTABLE LIFT
2, 4, 6 & 8 POST ARRANGEMENTS
MOHAWK RESOURCES LTD.
65 VROOMAN AVENUE
P. O. BOX 110
AMSTERDAM, NY 12010
TOLL FREE: 1-800-833-2006
FAX:
1-518-842-1289
LOCAL:
1-518-842-1431
READ MANUAL THOROUGHLY BEFORE
INSTALLING,
OPERATING OR SERVICING THIS LIFT!!
Deliver these instructions to lift
owner/user/employer along with other
instructional materials furnished with this lift.
Mohawk File: MP-18-24VDC
Series 12-18-2013.doc
Rev: 12-18-2013
Part No.: 601-800-373
1
IMPORTANT SAFETY INSTRUCTIONS
When using this garage equipment, basic safety precautions should always be followed,
including the following:
1.
Read all instructions.
2.
Inspect lift daily. Do not operate if it malfunctions or problems have been encountered.
3.
Never attempt to overload the lift. The manufacturer’s rated capacity is shown on the
identification label on the power side column. Do not override the operating controls or the
warranty will be void.
4.
Only trained and authorized personnel should operate the lift. Do not allow customers or
bystanders to operate the lift or be in the lift area.
5.
Position the lift support forks to contact the vehicle tires. Raise the lift until the forks contact
the tires. Check forks for secure contact with the vehicle tires, then raise the lift to the desired
working height.
6.
NOTE: Always use all 4 posts to raise and support vehicle.
7.
Note that the removal or installation of some vehicle parts may cause a critical load shift in the
center of gravity and may cause the vehicle to become unstable. Refer to the vehicle
manufacturer’s service manual for recommended procedures.
8.
Always keep the lift area free of obstructions and debris. Grease and oil spills should always be
cleaned up immediately.
9.
Never raise vehicle with passengers inside.
10. Before lowering check area for any obstructions.
11. Before driving vehicle between the posts, position the lift forks to allow vehicle to freely enter
lifting area. To not hit or run over forks as this could damage the lift and/or the vehicle.
12. Before removing the vehicle from the lift area, position the lift forks to allow vehicle to freely
leave lifting area. To not hit or run over forks as this could damage the lift and/or the vehicle.
13. Care must be taken as burns can occur from touching hot parts.
14. Do not operate equipment with a damaged cord or if the equipment has been dropped or
damaged – until a qualified serviceman has examined it.
15. Do not let cords hang over tables, benches or counters or come in contact with hot manifolds or
moving fan blades.
16. If an extension cord is necessary, a cord with a current rating equal to or more than that of the
equipment should be used. Cords rated for less current than the equipment may overheat. Care
should be taken to arrange the cord so that it will not be tripped over or pulled.
17. Always unplug the equipment from electrical outlet when not in use. Never use the cord to pull
the plug from the outlet. Grasp plug and pull to disconnect.
18. Let equipment cool completely before pulling away. Loop cord loosely around equipment
when storing.
19. To reduce the risk of fire, do not operate equipment in the vicinity of open containers of
flammable liquids (gasoline).
20. Adequate ventilation should be provided when working on operating internal combustion
engines.
21. Keep hair, loose clothing, fingers, and all parts of body way from moving parts.
22. To reduce the risk of electrical shock, do not use on wet surfaces or expose to rain.
23. Use only as described in this manual. Use only manufacturer’s recommended attachments.
24. ALWAYS WEAR SAFETY GLASSES. Everyday eyeglasses have only impact resistant
lenses, and they are NOT safety glasses.
SAVE THESE INSTRUCTIONS
MP-18 24VDC- Series Model Name Matrix:
Mohawk Number
Total Lift ----------------- Fork Lengths ------------------Model Name of Posts: Capacity (lbs): Post 1&2 Post 3&4 Post 5&6 Post 7&8
MP-18-505
2
36,000
15"
N/A
N/A
N/A
MP-18-509
2
32,000
22"
N/A
N/A
N/A
MP-18-513
2
32,000
22"W
N/A
N/A
N/A
MP-18-506
MP-18-518
MP-18-530
MP-18-510
MP-18-514
4
4
4
4
4
72,000
68,000
68,000
64,000
64,000
15"
15"
15"
22"
22"W
15"
22"
22"W
22"
22"W
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
MP-18-507
MP-18-524
MP-18-558
MP-18-525
MP-18-559
MP-18-511
MP-18-515
6
6
6
6
6
6
6
108,000
104,000
104,000
100,000
100,000
96,000
96,000
15"
15"
15"
15"
15"
22"
22"W
15"
15"
15"
22"
22"W
22"
22"W
15"
22"
22"W
22"
22"W
22"
22"W
N/A
MP-18-508
MP-18-526
MP-18-560
MP-18-527
MP-18-561
MP-18-528
MP-18-562
MP-18-512
MP-18-516
8
144,000
15"
15"
15"
8
140,000
15"
15"
15"
8
140,000
15"
15"
15"
8
136,000
15"
15"
22"
8
136,000
15"
15"
22"W
8
132,000
15"
22"
22"
8
132,000
15"
22"W
22"W
8
128,000
22"
22"
22"
8
128,000
22"W
22"W
22"W
Notes:
All Posts with 15" Forks are Rated 18,000 lbs each.
All Posts with 22" Forks are Rated 16,000 lbs each.
W - Denotes Wider Fork Lifts
iii
N/A
N/A
N/A
N/A
N/A
N/A
15"
22"
22"W
22"
22"W
22"
22"W
22"
22"W
The Automotive Lift Institute (ALI) is a trade association comprised of US and Canadian
manufacturers and certain national distributors of automotive lifts. For almost 50 years, the ALI
in cooperation with the American National Standards Institute (ANSI) has continued to sponsor
the national standard ANSI/ALI ALCTV:2011 "Safety Requirements for Construction, Testing,
and Validation for Automotive Lifts.”
The new "ALI/ETL Automotive Lift Certification Program" is based on ALI developed methods
and criteria for third party testing of automotive lifts to validate conformance with ANSI/ALI
ALCTV:2011.
For automotive lifts to be certified, manufacturers must execute an agreement with the ALI and
ETL / Intertek Testing Services and must meet certain requirements:

Must be structurally tested in accordance with the test requirements as outlined in ANSI/ALI
ALCTV:2011.

All motor operated units must be listed by a nationally recognized testing laboratory (NRTL)
in accordance with ANSI/UL-201.

The manufacturer's production facility must meet quality control requirements as set forth in
the ANSI Z34.1-1987 and the ALI/ETL Automotive Lift Certification Program Procedural
Guide.

All manufacturer-provided instructions, manuals, and operator safety documents, must meet
the requirements of the ANSI/ALI ALCTV:2011 and ANSI/UL-201.
Lifts meeting these rigid requirements may be listed in the directory of certified lifts and be
labeled with the "ALI/ETL certification mark" (Above on right), and, if applicable, the ETL
listing mark to ANSI/UL-201.
Mohawk has been a long-standing member of ALI and most of Mohawk’s popular models are
currently listed and certified. Other Mohawk models are in various stages of testing. To obtain a
complete and current certification listing, contact Mohawk Resources Ltd. or visit
www.mohawklifts.com or www.ali-directory.org To obtain a copy of the current automotive
lift standard, contact ALI or ANSI or visit www.autolift.org
Some people purchase quality products and others do not. You are assured of quality when you
purchase a Mohawk product in compliance with the certification program.
iv
HAVE A QUESTION?
Call your local
Mohawk distributor
For parts, service and technical support.
Distributor Place Card Here
Please have this unit’s model and serial number when calling for service.
Model Number ______________________
Serial Number ______________________
OR CONTACT:
MOHAWK RESOURCES LTD.
65 Vrooman Ave.
P.O. Box 110
Amsterdam, NY 12010
Toll Free: 1-800-833-2006
Local: 1-518-842-1431
Fax: 1-518-842-1289
Internet: www.MOHAWKLIFTS.com
E-Mail: [email protected]
v
MOHAWK WARRANTIES
EFFECTIVE DATE: 8/1/2013*
GENERAL WARRANTY INFORMATION:
MOHAWK’S OBLIGATION UNDER THIS WARRANTY IS LIMITED TO REPAIRING OR REPLACING ANY PART OR PARTS
RETURNED TO THIS FACTORY, TRANSPORTATION CHARGES PREPAID, WHICH PROVE UPON INSPECTION TO BE
DEFECTIVE AND WHICH HAVE NOT BEEN MISUSED. DAMAGE OR FAILURE TO ANY PART DUE TO FREIGHT DAMAGE OR
LACK OF REQUIRED REGULAR DOCUMENTED MAINTENANCE IS NOT COVERED UNDER THIS WARRANTY. ALL
WARRANTY CLAIMS MUST BE PERFORMED IN ACCORDANCE TO MOHAWK’S WARRANTY PARTS RETURN POLICY
(CONTACT MOHAWK’S SERVICE DEPARTMENT FOR MORE INFORMATION).
THIS WARRANTY DOES NOT COVER MIS-DIAGNOSING OF UNIT OR PARTS RETURNED THAT ARE NON-DEFECTIVE. THIS
WARRANTY DOES NOT COVER ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES INCLUDING, BUT NOT LIMITED TO,
LOST REVENUES OR BUSINESS HARM. THIS EQUIPMENT HAS BEEN DESIGNED FOR USE IN NORMAL COMMERCIAL
VEHICLE MAINTENANCE APPLICATIONS. A SPECIFIC INDIVIDUAL WARRANTY MUST BE ISSUED FOR UNITS THAT
DEVIATE FROM INTENDED USAGE, SUCH AS HIGH CYCLE USAGE IN INDUSTRIAL APPLICATIONS, OR USAGE IN
EXTREMELY ABUSIVE ENVIRONMENTS, ETC. MOHAWK RESERVES THE RIGHT TO DECLINE RESPONSIBILITY WHEN
REPAIRS HAVE BEEN MADE OR ATTEMPTED BY OTHERS. THIS WARRANTY DOES NOT COVER LABOR. THIS WARRANTY
DOES NOT COVER DOWNTIME EXPENSES INCURRED WHEN UNIT IS IN REPAIR. THE LIFT MUST BE REGISTERED
WITHIN 30 DAYS OF INSTALLATION BY MAILING SUPPLIED WARRANTY REGISTRATION CARD TO MOHAWK AND MUST
BE SIGNED BY A LICENSED ELECTRICIAN. THE MODEL NAME AND SERIAL NUMBER OF THE EQUIPMENT MUST BE
FURNISHED WITH ALL WARRANTY CLAIMS. THIS WARRANTY STATEMENT CONTAINS THE ENTIRE AGREEMENT
BETWEEN MOHAWK RESOURCES LTD. AND THE PURCHASER UNLESS OTHERWISE SPECIFICALLY EXPRESSED IN
WRITING. THIS NON-TRANSFERABLE WARRANTY APPLIES TO THE ORIGINAL PURCHASER ONLY. THIS WARRANTY IS
APPLICABLE TO UNITS LOCATED ONLY IN THE UNITED STATES OF AMERICA AND CANADA. CONTACT MOHAWK
RESOURCES LTD. FOR SPECIFIC WARRANTY PROVISIONS FOR UNITS LOCATED OUTSIDE OF THESE COUNTRIES.
THIS WARRANTY DOES NOT COVER NORMAL SURFACE WEAR ITEMS, ITEMS SUBJECT TO ABRASION, OR ITEMS USED
IN A CORROSIVE ENVIRONMENT. SOME ITEMS ON LIFT ARE SUBJECT TO NORMAL “WEAR AND TEAR” AND ARE NOT
COVERED UNDER THIS WARRANTY.
STRUCTURAL COMPONENTS (ALL LIFTS):
STRUCTURAL AND MECHANICAL COMPONENTS OF THIS UNIT ARE GUARANTEED FOR THE BELOW STATED TIME
FRAME, SPECIFIC TO MODEL LISTED, FROM THE DATE OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN
WORKMANSHIP AND/OR MATERIALS WHEN LIFT IS INSTALLED AND USED ACCORDING TO SPECIFICATIONS.
25-YEARS STRUCTURAL / 10 YEARS MECHANICAL: MODELS A-7, SYSTEM IA-10, LC-12, LC-12-3SA, LMF-12, TP-16, TP18, TP-20, TP-26, TP-30. STRUCTURAL ITEMS COVERED INCLUDE LEG, CARRIAGE, SWING ARM AND SLIDER
WELDMENTS (EXCLUDING NORMAL WEAR AREAS AS STATED ABOVE). MECHANICAL ITEMS COVERED INCLUDE
ROLLER BEARINGS AND LIFTING CHAIN.
5-YEAR: MODELS TL-7.
3-YEAR: MODELS TR-19, TR-25, FL-25, TR-30, TR-33, TR-35, TR-50, TR-75, TR-110, TR-120, MP-SERIES, RP-SERIES LIFTS.
2-YEAR: MODELS PARALLELOGRAM SERIES LIFTS.
1-YEAR: MODELS TD-1000, TD-2000, CT-1000, USL-6000.
POWER UNIT (ALL LIFTS):
ALL POWER UNIT COMPONENTS (MOTOR, PUMP AND RESERVOIR) ARE GUARANTEED FOR TWO YEARS FOR PARTS,
FROM THE DATE OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE
LIFT IS INSTALLED, CONNECTED BY A LICENSED ELECTRICIAN AND USED ACCORDING TO SPECIFICATIONS.
ELECTRICAL COMPONENTS (ALL LIFTS):
ALL ELECTRICAL COMPONENTS (EXCLUDING MOTOR) ARE GUARANTEED FOR ONE YEAR FOR PARTS, FROM THE
DATE OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE LIFT IS
INSTALLED AND USED ACCORDING TO SPECIFICATIONS.
PNEUMATIC-AIR COMPONENTS (ALL LIFTS):
ALL PNEUMATIC (AIR) COMPONENTS (I.E. AIR CYLINDERS AND POPPET AIR VALVES) ARE GUARANTEED FOR ONE
YEAR FOR PARTS, FROM THE DATE OF SHIPMENT FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR
MATERIALS WHEN THE LIFT IS INSTALLED AND USED ACCORDING TO SPECIFICATIONS.
HYDRAULIC CYLINDERS (MODEL SPECIFIC LIFTS):
THE FOLLOWING MODELS ARE GUARANTEED FOR 5 YEARS (PARTS ONLY), FROM DATE OF SHIPMENT FROM
FACTORY, FOR HYDRAULIC CYLINDERS, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE LIFT IS
INSTALLED AND USED ACCORDING TO SPECIFICATIONS: A-7, SYSTEM IA-10, LC-12, LC-12-3SA, LMF-12, TP-16, TP-18,
TP-20, TP-26, TP-30.
ALL OTHER MODELS ARE GUARANTEED FOR TWO YEARS (PARTS ONLY), FROM THE DATE OF SHIPMENT FROM
FACTORY, FOR HYDRAULIC CYLINDERS, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN THE LIFT IS
INSTALLED AND USED ACCORDING TO SPECIFICATIONS (EXCLUDING USL-6000, WHICH IS ONE YEAR).
AFTER THE FIRST 5 YEARS FROM DATE OF SHIPMENT FROM FACTORY, THE “EXTENDED LIFETIME CYLINDER SEAL
WARRANTY” (BELOW) IS APPLICABLE TO THE FOLLOWING MOHAWK LIFTS ONLY: A-7, SYSTEM IA-10, LC-12, LC-12-3SA,
LMF-12, TP-16, TP-18, TP-20, TP-26, TP-30. SEE MOHAWK’S “EXTENDED LIFETIME CYLINDER SEAL WARRANTY” FOR
SPECIFIC WARRANTY PROVISIONS FOR HYDRAULIC CYLINDERS.
THE “EXTENDED LIFETIME CYLINDER SEAL WARRANTY” IS AS FOLLOWS:
AS THE ORIGINAL PURCHASER OF A MOHAWK LIFT MANUFACTURED BY MOHAWK RESOURCES, LTD. YOU ARE
ENTITLED TO AN EXTENDED CYLINDER SEAL WARRANTY. TO QUALIFY FOR THIS WARRANTY, THE FOLLOWING
CONDITIONS MUST BE MET:
ALL LIFTS MUST BE REGISTERED WITH MOHAWK RESOURCES, LTD., P.O. BOX 110, 65 VROOMAN AVENUE,
AMSTERDAM, NY 12010, WITH THE ORIGINAL CUSTOMER NAME, ADDRESS AND PHONE NUMBER, WITHIN 30 DAYS OF
INSTALLATION. (USE POSTAGE PAID WARRANTY REGISTRATION CARD ATTACHED TO THE FRONT OF THE MANUAL
PROVIDED.)
MOHAWK’S OBLIGATION UNDER THIS WARRANTY IS LIMITED TO SUPPLYING MODEL SPECIFIC CYLINDER SEALS. THE
CUSTOMER IS RESPONSIBLE FOR SHIPPING AND HANDLING OF THE SEALS. MOHAWK IS NOT RESPONSIBLE/LIABLE
FOR THE REBUILD OF CYLINDERS BY OTHERS. THIS WARRANTY IS NON-TRANSFERABLE AND RUNS TO THE ORIGINAL
PURCHASER ONLY.
STANDARD OPTIONS (ALL LIFTS):
ALL STANDARD OPTIONS OF THIS UNIT ARE GUARANTEED FOR ONE YEAR FOR PARTS, FROM THE DATE OF SHIPMENT
FROM FACTORY, AGAINST DEFECTS IN WORKMANSHIP AND/OR MATERIALS WHEN LIFT IS INSTALLED AND USED
ACCORDING TO SPECIFICATIONS.
CUSTOM LIFTS AND OPTIONS:
ALL “CUSTOM” LIFTS AND/OR “CUSTOM” OPTIONS ARE GUARANTEED ON A CASE-BY-CASE BASIS. CONSULT MOHAWK
FACTORY FOR DETAILS ON SPECIFIC CUSTOM LIFTS AND/OR OPTIONS.
WARRANTY EXCEPTIONS (ALL LIFTS):
ADJUSTMENTS: THIS WARRANTY DOES NOT COVER CASUAL AND ROUTINE ADJUSTMENTS SUCH AS, BUT NOT
LIMITED TO: FITTINGS, ANCHOR BOLT RE-TIGHTENING, OR ANY SHIMMING OR ADJUSTMENTS REQUIRED DURING A
PROPER AND PROFESSIONAL INSTALLATION BY A QUALIFIED INSTALLER.
MAINTENANCE AND INSPECTIONS: IF THIS UNIT IS NOT MAINTAINED AND INSPECTED IN ACCORDANCE TO THE
RELEVANT SECTIONS IN THE USERS MANUAL FOR THIS SPECIFIC MODEL, WARRANTY IS VOID. OSHA, ANSI AND
MOHAWK REQUIRE THAT RECORDS MUST BE MAINTAINED TO PROVE THAT INSPECTIONS AND MAINTENANCE OF THIS
UNIT HAVE BEEN ROUTINELY PERFORMED BY QUALIFIED INDIVIDUALS.
ABUSE: IF THIS UNIT IS FOUND TO BE OVERLOADED (PURPOSELY OR UNKNOWINGLY), USED IN A SITUATION BEYOND
ITS INTENDED FUNCTION, NOT MAINTAINED OR INSPECTED REGULARLY, OR USED IN AN ABUSIVE ENVIRONMENT OR
BEYOND NORMAL SHOP USAGE, ETC., THIS WARRANTY IS VOID IN ITS ENTIRETY.
NON-EXISTENT PROBLEMS: FOR SERVICE VISITS, PART REPLACEMENTS, LABOR, ETC. FOR PARTS FOUND TO BE
NON-DEFECTIVE, OR FOR A UNIT DIS-FUNCTION THAT DOES NOT EXIST, IT IS THE LIFT OWNER THAT REQUESTED THE
SERVICE VISIT WHO BEARS THE RESPONSIBILITY OF ALL RELATED EXPENSES.
BATTERIES: ALL BATTERIES CARRY THE BATTERY MANUFACTURER’S WARRANTY. MAINTENANCE REQUIREMENTS
AND ABUSE PROVISIONS ARE AS STATED BY THE BATTERY MANUFACTURER. REFER TO BATTERY MANUFACTURER’S
WARRANTY.
SPECIAL/MODIFIED INSTALLATIONS: THIS WARRANTY DOES NOT COVER “NON-TRADITIONAL” INSTALLATIONS.
INSTALLATIONS ARE TO BE DONE ACCORDING TO SPECIFICATIONS, OR THE WARRANTY IS VOID.
WEARABLE COMPONENTS: SOME ITEMS ON LIFTS ARE SUBJECT TO NORMAL “WEAR AND TEAR” AND ARE NOT
COVERED UNDER THIS WARRANTY.
* THIS WARRANTY SUPERSEDES ALL OTHER WARRANTY POLICIES PREVIOUSLY STATED AND IN ALL OTHER
MOHAWK PRODUCT SPECIFIC LITERATURE (MANUALS, BROCHURES, ETC.).
CONTENTS
TEXT
PAGE
GENERAL NOTES & WARNINGS
LIFT LIMITATIONS
POWER SUPPLY REQUIRMENTS
OPTIONAL EQUIPMENT
LIFT SPECIFICATIONS (15” FORK MODEL)
LIFT SPECIFICATIONS (22” FORK MODEL)
DESIGN & CONSTRUCTION FEATURES
MOBILE LIFT SET-UP
MOBILE LIFT OPERATION
FINAL CHECKOUT
SAFETY TIPS
MAINTENANCE INSTRUCTIONS
EXPLANATION OF COMPUTER SYSTEM
TROUBLE SHOOTING
MAINTENANCE & SERVICE CHART
1
2
3
4
5
6
7
8-9
10-11
12
13
14
15-22
23-24
25
PARTS
DWG NO.
POST ASSEMBLY (15” FORKS)
POST ASSEMBLY (22” FORKS)
JACK ASSEMBLY
POWER UNIT ASSEMBLY
FLOOR ROLLER ASSEMBLY
LOCK ASSEMBLY
CARRIAGE ASSEMBLY
CYLINDER ASSEMBLY
CONTROL BOX ASSEMBLY
CONTROL BOX SUB-ASSEMBLY
CONTROL PANEL ASSEMBLY
TERMINAL STRIP #1 ASSEMBLY
TERMINAL STRIP #2 ASSEMBLY
CHARGER ASSEMBLY
STRING POT ASSEMBLY
BATTERY BOX ASSEMBLY
PENDANT ASSEMBLY (OPTIONAL)
MP-5400-A-001
MP-5400-A-004
MP-0400-A-007
MP-5400-A-003
MP-0500-A-001
MP-5200-A-001
MP-0700-A-001
MP-0900-A-001
MP-5100-A-001
MP-5100-A-003
MP-5100-A-004
MP-5100-A-020
MP-5100-A-021
MP-5100-A-012
MP-5100-A-014
MP-5300-A-001
MP-1300-A-020
ILLUSTRATIONS
CHARGER STATUS LIGHTS
BATTERY METER LIGHTS
JACK OPERATION
JACK RELIEF SETTING
ENCLOSURE DIAGRAMS
COMMUNICATION CABLE & DUMMY PLUG DIAGRAMS
WARNINGS PICTOGRAM
CAUTIONS PICTOGRAM
SAFETY INSTRUCTIONS PICTOGRAM
SCHEMATICS
DWG NO.
HYDRAULIC SCHEMATIC
ELECTRICAL SCHEMATIC & WIRING DIAGRAMS (3 PAGES)
MP-5000-A-002
MP-5000-A-001
CHARGER
CHARGER INFORMATION
BATTERY CARE
BATTERY INFORMATION
OPTIONS
ALL INFORMATION, ILLUSTRATIONS, AND SPECIFICATIONS IN THIS MANUAL ARE BASED ON THE LATEST PRODUCT INFORMATION
AVAILABLE AT THE TIME OF PRINTING. WE RESERVE THE RIGHT TO MAKE CHANGES AT ANY TIME WITHOUT NOTICE.
viii
GENERAL NOTES & WARNINGS
RECOMMENDATIONS BY THE INDIVIDUAL USER OR USING ORGANIZATION FOR IMPROVING THIS PUBLICATION OR ANY ASPECT OF THE
PRODUCT ARE ENCOURAGED AND SHOULD BE FORWARDED IN WRITING TO:
MOHAWK RESOURCES LTD, SERVICE DEPT, 65 VROOMAN AVENUE, AMSTERDAM, NY 12010
THIS IS NOT A VEHICLE LIFTING PROCEDURE MANUAL AND NO ATTEMPT IS MADE OR IMPLIED HEREIN TO INSTRUCT THE USER IN
LIFTING METHODS PARTICULARLY TO THE INDIVIDUAL APPLICATION OF THE EQUIPMENT DESCRIBED IN THIS MANUAL. RATHER, THE
CONTENTS OF THIS MANUAL ARE INTENDED AS A BASE LINE FOR OPERATION, MAINTENANCE, TROUBLE SHOOTING, AND PARTS LISTING
OF THE UNIT AS IT STANDS ALONE AND AS IT IS INTENDED AND ANTICIPATED TO BE USED IN CONJUNCTION WITH OTHER EQUIPMENT.
PROPER APPLICATION OF THE EQUIPMENT DESCRIBED HEREIN IS LIMITED TO THE PARAMETERS DETAILED IN THE SPECIFICATIONS AND
THE USES SET FORTH IN THE DESCRIPTIVE PASSAGES. ANY OTHER PROPOSED APPLICATION OF THIS EQUIPMENT SHOULD BE
DOCUMENTED AND SUBMITTED IN WRITING TO MOHAWK RESOURCES LTD. FOR EXAMINATION. THE USER ASSUMES FULL
RESPONSIBILITY FOR ANY EQUIPMENT DAMAGE, PERSONAL INJURY, OR ALTERATION OF THE EQUIPMENT DESCRIBED IN THIS MANUAL
OR ANY SUBSEQUENT DAMAGES.
DO NOT WELD, APPLY HEAT, OR MODIFY THIS EQUIPMENT IN ANY MANNER WITHOUT WRITTEN AUTHORIZATION FROM MOHAWK
RESOURCES LTD. CERTAIN ALLOY OR HEAT-TREATED COMPONENTS MAY BE DISTORTED OR WEAKENED, RESULTING IN AN UNSAFE
CONDITION. MOHAWK RESOURCES LTD. IS NOT RESPONSIBLE FOR DISTORTIONS, WHICH RESULT FROM WELDING ON THIS EQUIPMENT
AFTER MANUFACTURING IS COMPLETED. UNAUTHORIZED WELDING, APPLICATION OF HEAT, OR MODIFICATION OF THIS EQUIPMENT VOIDS
ANY AND / OR ALL APPLICABLE WARRANTIES COVERING THIS EQUIPMENT.
ALL WARRANTIES APPLICABLE TO THIS EQUIPMENT ARE CONTINGENT ON STRICT ADHERENCE TO THE MAINTENANCE SCHEDULES AND
PROCEDURES IN THIS MANUAL.
KEEP ALL SHIELDS AND GUARDS IN PLACE. ENSURE ALL SAFETY MECHANISMS ARE OPERABLE. KEEP HANDS, FEET, AND CLOTHING
AWAY FROM POWER-DRIVEN AND MOVING PARTS.
WARNING
DO NOT INSTALL THIS UNIT IN A PIT OR DEPRESSION DUE TO FIRE OR EXPLOSION RISK
IMPORTANT NOTE
A LEVEL FLOOR IS SUGGESTED FOR A PROPER INSTALLATION SITE AND WILL ENSURE LEVEL LIFTING. ANY MAJOR SLOPE CHANGES
WILL AFFECT THE UNIT’S LEVEL LIFTING PERFORMANCE. IF A FLOOR IS OF QUESTIONABLE SLOPE, CONSIDER A SURVEY OF THE SIGHT
AND / OR THE POSSIBILITY OF POURING A NEW LEVEL CONCRETE SLAB SECTION. SIMPLY STATED, FOR OPTIMUM LEVEL LIFTING, THE
EQUIPMENT, AT BEST, CAN LIFT ONLY AS LEVEL AS THE FLOOR ON WHICH IT IS LOCATED... AND SHOULD NOT BE EXPECTED TO
COMPENSATE FOR DRASTIC FLOOR SLOPE DIFFERENCES.
THIS EQUIPMENT MUST BE USED ON A LEVEL CONCRETE FLOOR WITH A MINIMUM THICKNESS OF 4-1/2” ON GRADE. THE CONCRETE
MUST BE AGED AT LEAST (28) TWENTY EIGHT DAYS PRIOR TO INSTALLATION AND HAVE A MINIMUM COMPRESSIVE STRENGTH OF 3000
PSI. DO NOT USE THIS UNIT ON ANY ASPHALT SURFACE.
DO NOT USE THIS UNIT ON A SECOND FLOOR OR ANY GROUND FLOOR WITH A BASEMENT BENEATH WITHOUT WRITTEN AUTHORIZATION
FROM THE BUILDING ARCHITECT.
CAUTION
THE EQUIPMENT DESCRIBED IN THIS MANUAL COULD BE POTENTIALLY DANGEROUS IF IMPROPERLY OR CARELESSLY OPERATED. FOR
THE PROTECTION OF ALL PERSONS AND EQUIPMENT, ONLY COMPETENTLY TRAINED OPERATORS WHO ARE CRITICALLY AWARE OF THE
PROPER OPERATING PROCEDURES, POTENTIAL DANGERS, AND SPECIFIC APPLICATION OF THIS EQUIPMENT SHOULD BE ALLOWED TO
TOUCH THE CONTROLS AT ANY TIME.
SAFE OPERATION OF THIS EQUIPMENT IS DEPENDENT ON USE, IN COMPLIANCE WITH THE OPERATION PROCEDURES OUTLINED IN THIS
MANUAL ALONG WITH THE MAINTENANCE AND INSPECTION PROCEDURES WITH CONSIDERATION OF PREVAILING CONDITIONS.
THIS LIFT IS DESIGNED AND INTENDED FOR USAGE AND STORAGE INDOORS ONLY. MOHAWK DENIES ALL LIABILITY AND VOIDS
WARRANTY IN SITUATIONS WHERE THIS LIFT IS USED OR STORED WHERE IT IS SUBJECTED TO THE OUTDOOR ELEMENTS AND
TEMPERATURES.
THE EQUIPMENT DESCRIBED IN THIS MANUAL IS NEITHER DESIGNED NOR INTENDED FOR ANY APPLICATION ALONE OR IN CONJUNCTION
WITH ANY OTHER EQUIPMENT THAT INVOLVES THE LIFTING OR MOVING OF PERSONS.
ALWAYS CONSULT THE VEHICLE LIFTING GUIDE FOR THE PROPER LIFTING POINTS ON ANY VEHICLE. THESE GUIDES ARE AVAILABLE
FROM THE VEHICLE MANUFACTURERS. ALSO, REFER TO THE ANSI STANDARD “VEHICLE LIFT POINTS FOR SERVICE GARAGE LIFTING,”
ANSI/SAE J2184-OCT92, SAFETY MANUAL “LIFTING IF RIGHT,” ALI/SM01, AND “VEHICLE LIFTING POINTS GUIDE” ALI/LP-GUIDE FOR PROPER
POSITIONING OF VEHICLES ON LIFT.
AFTER LIFTING THE VEHICLE TO THE DESIRED HEIGHT, ALWAYS LOWER THE UNIT ONTO THE MECHANICAL SAFETIES. THE FORMING OF
GOOD OPERATIONAL WORK HABITS WILL ELIMINATE OVERSIGHTS IN THE USE OF PROVIDED SAFETY DEVICES.
1
APPENDAGE:
Rev (9/1/2012)
LIFT ENVIRONMENT LIMITATIONS:
Mohawk prohibits the outdoor installation of this standard lift, which is APPROVED FOR INDOOR USAGE ONLY,
in a normal garage type environment. Any concerns in applications that expose the lift to additional environmental
effects, such as paint booths, wash bays, outdoors, high or low temperatures, etc. must be addressed to our engineering
department, where provisions could/may be made to the lift to accommodate the area of use. Our engineering
department must be made aware in advance of these conditions and any additional code requirements that must be met.
Also, the foundation for which this lift must be installed on must comply to the minimum specifications as set forth in
this manual. Any drainage slopes in the bay where the lift is to be installed must be directed away from the posts to
prevent water accumulation at the post bases.
Standard floor requirements are contained within this manual. For installation within a seismic area, a qualified person
must be consulted to address seismic loads and other local or state requirements.
LOCKOUT/TAGOUT REQUIREMENTS:
The start switch provided with this unit must not be used as a primary disconnecting means. A separate disconnecting
means must be provided in accordance with all applicable codes. It is the responsibility of the owner/user of this unit to
provide a proper lockout/tagout device for this unit before or during installation in conformance to ANSI Z244.1 and
any local/state/national electrical codes and any OSHA regulations.
OTHER LIFT LIMITATIONS:
All Mohawk MP-Series lifts must accomplish three main criteria in order to lift a vehicle safely:
1. Proper capacity. All MP-Series lifts are designed to lift standard vehicles within their rated capacity within the
capacity of the lift rating. Any vehicles exceeding the capacity must not be raised. Ensure that individual
columns are used within their capacity and are not overloaded (ie. heavy ended vehicles may overload the rear
pair of columns).
2. Proper engagement of tires/frame: ensure tires are fully engaging all tires or proper frame components of
vehicle. Ensure frame components used are capable of supporting vehicle.
3. Proper flooring. Use lifts on floors complying to required specs stated within this manual.
This lift is not intended to be driven on or off of, as this may damage the lift and the vehicle.
This lift is not intended for the lifting of people.
Care must be observed when removing any heavy components from a vehicle and thereby drastically shifting the
vehicle center of gravity (i.e. engine removal, transmission removal, etc.). The use of jack stands at the front and rear
ends of the vehicle is highly recommended when performing this type of work.
File: MP-Appen.doc
2
POWER SUPPLY REQUIREMENTS
This lift comes with (2) 12 VDC batteries in series to provide a 24 VDC system. A separate 120 VAC power
supply is only required when charging the post. Each post comes equipped with a 120 VAC, 60 HZ receptacle
which accepts a 120 VAC extension cord. The minimum amp draw is 3 amps per post. Use sizes of plug, cord
and power supply as follows:
Plug Requirements:
NEMA Type 5-15 (Female), 125 VAC, 2 Pole, 3 Wire Grounding, 15 Amp Rated.
Cord Requirements:
3 Wire, 125 VAC, 15 Amp Rated, Oil Resistant, Type G, SO, STO, or W. (Maximum Length is 50 feet)
Power Requirements:
115-120 VAC, 2 Pole, 3 Wire Grounding, 60 Hz, 3 Amps minimum per post. Size circuit breaker to NEC and
local codes.
WARNING: Keep in mind that branching extension cords between posts will multiply the amp draw.
(i.e. 6 posts will collectively draw 18 amps).
NOTE THAT THESE POSTS WILL NOT OPERATE AND CHARGE AT THE SAME TIME.
REMOVE THE POWER LEADS TO THE CHARGER RECEPTACLE PRIOR TO LIFT USAGE.
3
OPTIONAL EQUIPMENT
Note: Refer to Option Equipment Section in the back of this manual for specific user instructions for option
available for this lift.
The standard mobile lift is suitable to lift wheeled vehicles by the tires. It normally comes in pairs of columns
totaling 2, 4, 6 or 8 column systems. Ordering additional dummy plugs may enable one lift to be used in a
variety of combinations simultaneously.
A hand control pendant is available and can be connected to any column.
If it is desired to raise the vehicle by the frame, this can be done by using optional chassis lifting beams or
optional frame contact adapters. The chassis lift beam fits into the cradle where the tire would normally fit
and spans between a pair of columns. Frame contact adapters convert a pair of mobile lift columns into a 2column frame engaging lift. Refer to the ANSI standard “Vehicle Lift Points for Service Garage Lifting,”
ANSI/SAE J2184-Oct92, safety manual “Lifting if Right,” ALI/SM01, and “Vehicle Lifting Points Guide”
ALI/LP-Guide for proper positioning of vehicles on lift.
If it is desired to raise fork trucks, a fork truck adapter kit is available, which converts a pair of mobile lift
columns into a 2-column pad engaging lift.
For lifting applications involving side wing plows or RV’s with side extensions, where the forks of the mobile
lifts can not reach to the tires, wing plow adapters are available. These adapters span between a pair of
columns to achieve engagement of the tires in the same manner of the column forks.
For lifting of vehicles with dual tires, floatation tires, or “super singles”, longer forks are available. Note that
the longer fork lifts have reduced capacity.
Jack Stands are also available that support the vehicle in the raised position for maintenance or to permit
using the lift for other vehicles.
NOTE:
The use of any adapters on this lift may reduce the capacity of this lift. Refer to the capacities of the adapters
used.
WARNING!
Use only options manufactured by MOHAWK RESOURCES LTD with this lift. Options
manufactured by others and used on this lift may result in bodily harm, damage to lift and
other equipment, and will void lift warranty, Mohawk Resources Ltd liability, and the ALI
certification of the lift.
4
DESIGN AND CONSTRUCTION
The standard mobile lift is suitable to lift wheeled vehicles by the tires. It normally comes in pairs of
columns totaling 2, 4, 6 or 8 column systems. Each column consists of a rigid frame of three-wheel design
for maneuverability, lifting carriages with tire forks, control panel, electric-hydraulic power unit, and
hydraulic cylinder.
Two of the wheels are spring loaded and in fixed positions on the column base. The third wheel is steerable
and hydraulically operated, permitting movement of the unloaded columns, but allowing the column to sit
firmly on the floor before a load is applied.
Since this lift is battery powered, each post is identical except for post identification (Post ID), and each has
communication outlets to attach to the other posts, forming configurations from 2 posts all the way up to 8
posts (see lift setup).
When the lift is raised or lowered in the “synchronized” mode the actual movement of each carriage is
measured and compared by each post’s PLC (programmed logic controller). If the movement of any carriage
exceeds that of any other carriage in the system, the carriage is slowed down or stopped until the others catch
up.
The each post houses the same controls, enabling the user to control the whole lift, a single post or a postpair combo at any post desired.
A hydraulic cylinder, powered by an electric-hydraulic pump unit, controls the carriage movement. There is
an internal relief valve on the pump unit, which prevents overloading of the carriage.
A separate automatically engaging back-up mechanical safety lock latch prevents lowering of the carriage in
the event of failure of the hydraulic system.
All movement controls are of the “vigilance control” type which are operable only as long as the operator is
depressing the button. As soon as the button is released the motion will stop.
All columns have controls for synchronized or individual column movement, plus an “Emergency Stop”.
Depressing the Emergency Stop button will stop all columns immediately and will not permit any column
movement until the depressed button is reset.
7
MOBILE LIFT SET-UP
THOROUGHLY READ THIS SECTION BEFORE OPERATING THE LIFT. IF YOU HAVE ANY
QUESTIONS, GET THEM ANSWERED BEFORE PROCEEDING. REFER TO ANSI/ALI ALIS
“SAFETY REQUIREMENTS FOR INSTALLATION AND SERVICE OF AUTOMOTIVE LIFTS.”
1. Be sure that the floor is strong enough to support the lift before operating. Do not use the lift on asphalt
surfaces, as the lift will sink (cause depressions in the asphalt) if the vehicle is on the lift for any
extended period of time. Minimum recommended flooring is 4 ½” thick concrete with 3000 psi
compressive strength on grade.
If it is necessary to use the lift on an asphalt surface, it is recommended to use a steel plate, a minimum
thickness of 3/8” (8mm) which extends a minimum of 6” on all sides beyond the support points of the
base of the lift. This will minimize sinking effect if the vehicle is raised for an extended period of time.
2. Be sure that the surface of the floor is relatively flat. If there is a slope of more than 3 degrees (1 inch
decline over 20”) do not operate the lift. Relocate to a flatter surface.
3. Verify adequate ceiling clearance to raise the vehicle without the top of the vehicle coming in contact
with any obstruction. If necessary, measure the lowest point to determine how high you can raise the
vehicle. Minimum height required is the tallest vehicle height plus 67”. NOTE: the maximum lifting
height of these columns is an adjustable setting in the PLC. Contact the factory if you wish to lower the
lifting height for a low ceiling or other overhead obstructions.
4. Drive the vehicle to the working spot. Do not drive the vehicle over the cables of the lift. The cables
should be arranged in a “U” shape around the entry of the vehicle or the cables should be disconnected
and stored before moving the vehicle.
5. Unplug all power leads to chargers on all posts.
6. Ensure posts pairs are opposite each other at each axle (Post Pairs are 1&2, 3&4, 5&6, 7&8). Push the
cradle forks of each post around each tire. Be sure to push them in as far as possible. The wheel rim
should be larger than the opening in between the forks. See figure below. Ensure that fork pins are placed
in holes at fork tubes.
8
7. Press the release lever to lower all jacking wheels on back of all posts after positioning.
8. Connect the communication cables from post to post in a daisy-chain fashion. For example: Posts 1 to 3
to 4 to 2 for a 4-post setup. Place dummy plugs (male and female ends) at the posts at the end of the
chain. (See figure below) Note: This lift indicates what posts are communicating within the system at
start up. (Refer to Explanation of Computer System – System Activation Section)
9
MOBILE LIFT OPERATION
1. Perform Lift Setup as stated in previous section.
2. Disengage all E-STOP buttons at each post by turning them clockwise to release them. Turn on the main
switch for each post to “OPERATE LIFT”. The display will light up to indicate the post power is on.
Repeat for each post in the system. Notice that the displays will indicate which posts are communicating
in the system. Verify this configuration to continue operation. The system is now ready to operate.
3. SINGLE WHEEL OPERATION
Go to each wheel and engage each tire with the forks. To raise only a single wheel, turn the selector
switch to SINGLE at the post that control is desired, while pressing the RAISE button. The SINGLE
operation is to be used only to initially engage the tires and for slight equalization adjustments.
During lift operation, if single wheel lifting, lowering or parking is desired, turn the selector switch to
SINGLE at the post that control is desired, while pressing the RAISE button.
BE VERY CAREFUL WHEN DOING THIS OPERATION THAT THE VEHICLE REMAINS
STABLE AND THAT THE SIDE OF THE VEHICLE DOES NOT COME IN CONTACT WITH THE
COLUMN.
NOTE: If the SINGLE switch is released while the UP or DOWN button is still pressed the hoist will
operate in default ALL synchronized mode (All posts will be controlled).
4. RAISING ALL WHEELS
The lift controls default to controlling ALL the columns in the system (selector switch is spring returned
to ALL). Press the RAISE button to raise the lift. Keep the pressure on the button until the vehicle is
raised to the desired position. If necessary, use a second person to observe the area not seen by the
operator.
5. PARKING ALL WHEELS (ON MECHANICAL LOCKS)
The lift controls default to controlling ALL the columns in the system. Press the PARK button to lower
the lift onto the mechanical locks. Keep the pressure on the button until the vehicle is completely
lowered onto the locks. If necessary, use a second person to observe the area not seen by the operator.
6. LOWERING ALL WHEELS
The lift controls default to controlling ALL the columns in the system. Press the LOWER button to
lower the lift. Keep the pressure on the button until the vehicle is lowered to the desired position. If
necessary, use a second person to observe the area not seen by the operator.
NOTE: If lift is in park position (on mechanical locks), you will have to raise lift off of locks first, then
lower. Lift will not automatically rise off of locks when pressing lower.
NOTE: IF FOR ANY REASON, THE LIFT BECOMES INOPERATIVE IN THE RAISED
POSITION WITH A VEHICLE ON IT, CONTACT YOUR LOCAL MOHAWK
REPRESENTATIVE OR THE MOHAWK FACTORY.
10
7. PAIR OPERATION
To raise, lower or park only a pair of wheels, turn the selector switch to PAIR at the post pair that control
is desired, while pressing the RAISE, LOWER or PARK button.
NOTE: Be sure that the set of wheels on the ground is free to move as the effective distance between the
front and rear wheels becomes less as one pair of wheels is higher or lower than the other pair. Keep the
height difference between pairs as low as practical.
NOTE: If the PAIR switch is released while the UP or DOWN button is still pressed the hoist will
operate in default ALL synchronized mode (All posts will be controlled).
LIFTING EXAMPLE:
Now that all the setup and operations instructions have been presented, an example of a typical lifting
application is shown:
A mechanic is to perform maintenance on a school bus. He drives the vehicle into the bay. He then unplugs
any power cables to the charger inlets on all of the posts to be used. He jacks each post with the pallet jack
and moves them to each of the tires in the post configuration shown in the setup diagram. Pushing the posts
firmly against the tires, he checks to ensure that the forks are slid inward as far as possible to engage the tires.
He presses the pallet jack release on each column. He then connects the communication cables and dummy
plugs to all the posts as shown in the setup diagram.
He is now ready to use the lift. He turns the main switch to “Operate Lift” and releases the E-Stop Button on
each post of the system. Once this is done, all the displays should illuminate. He reads the post
communication screen to verify that all the columns are present and accounted for on the display. He presses
the appropriate button on the screen to verify the post set-up. The lift system is now ready to operate.
The mechanic then goes to each post and presses UP and SINGLE for a short moment to engage each tire
with the forks until the spring loaded wheels of the post retract and the post feet are flattened on the floor.
(The SINGLE function is to be used for slight adjustments and to initially engage the tires ONLY). The
mechanic then presses UP and raises the vehicle to the desired height. Then the PARK button is pressed and
held until the vehicle stops on the mechanical locks.
The mechanic is now able to work on the vehicle. Once done, he presses UP to lift the vehicle off of the
mechanical locks. The DOWN button is pressed to lower the lift to the ground. If any adjustments where
made (like SINGLE or PAIR) which made the lift level vary from the floor level, the lift may experience a
fault when lowered to the floor. Pressing RESET will clear this fault and allow further lowering. Also,
reversing the adjustments by pressing SINGLE or PAIR will allow the user to lower the lift fully to the floor.
Once vehicle is fully lowered, cables are stored and posts are jacked up and pulled away.
11
LIFT FINAL CHECKOUT (AFTER INSTALLATION):
REV (9/1/2012)
THIS PROCEDURE OUTLINES THE FINAL CHECKS TO MAKE AFTER INITIAL INSTALLATION OF THE LIFT UNIT.
REPEAT THIS PROCEDURE IF THE LIFT IS RELOCATED.
AFTER THE LIFT IS FULLY ASSEMBLED, RAISE THE LIFT EMPTY A FEW TIMES TO VERIFY:

PROPER POWER INPUT TO ALL POSTS (NOT APPLICABLE TO DC COLUMNS)

PROPER COMMUNICATION OF ALL POSTS IN SYSTEM

POST RECOGNITION OF ALL POSTS IN SYSTEM

ALL POSTS RAISING SMOOTHLY AND ALL SYNCHRONIZED

NO LEAKS PRESENT AT ANY FITTING JUNCTIONS

LOCKS ARE ENGAGING ON ALL POSTS SIMULTANEOUSLY AS LIFT IS RAISING

LOCKS ARE DIS-ENGAGING ON ALL POSTS WHEN LOWERING BUTTON DEPRESSED.

LOCKS ARE RE-ENGAGING AFTER DIS-ENGAGED.

LIFT IS NOT DRIFTING DOWN WHEN RAISED (RAISE LIFT, THEN STOP, AND VERIFY DRIFT DOWN OF CYLINDERS)

NO VIBRATIONS FROM LOOSE CLAMPING, ETC.
ONCE THIS IS COMPLETE, LOCATE A REPRESENTATIVE VEHICLE INTO THE LIFTING AREA.
USE A VEHICLE THAT WEIGHS AT LEAST 50 PERCENT OF THE CAPACITY OF THE LIFT.
OBSERVING LIFTING PROCEDURES CONTAINED IN THIS MANUAL TO POSITION THE VEHICLE ONTO THE LIFT.
RAISE LIFT APPROXIMATELY 1 FOOT. VERIFY THE FOLLOWING:

ALL POSTS RAISING SMOOTHLY AND ALL SYNCHRONIZED

NO LEAKS PRESENT AT ANY FITTING JUNCTIONS

LOCKS ARE ENGAGING ON ALL POSTS SIMULTANEOUSLY AS LIFT IS RAISING (SOME VARIANCE EXPECTED)

LIFT IS NOT DRIFTING DOWN WHEN RAISED (RAISE LIFT, THEN STOP, AND VERIFY DRIFT DOWN OF CYLINDERS)

NO VIBRATIONS FROM LOOSE CLAMPING, ETC.
PRESS PARK. VERIFY THE FOLLOWING:

ALL POSTS LOWERING ONTO LOCKS
RAISE LIFT A FEW INCHES, THEM PRESS LOWER. VERIFY THE FOLLOWING:

ALL POSTS LOWERING SMOOTHLY AND ALL SYNCHRONIZED

NO LEAKS PRESENT AT ANY FITTING JUNCTIONS

NO VIBRATIONS FROM LOOSE CLAMPING, ETC.

LOCKS ARE NOT RE-ENGAGING WHILE LOWERING
RAISE LIFT TO FULL STROKE. VERIFY THE FOLLOWING:

ALL POSTS RAISING SMOOTHLY AND ALL SYNCHRONIZED

NO LEAKS PRESENT AT ANY FITTING JUNCTIONS

LOCKS ARE ENGAGING ON ALL POSTS SIMULTANEOUSLY AS LIFT IS RAISING (SOME VARIANCE EXPECTED)

LIFT IS NOT DRIFTING DOWN WHEN RAISED (RAISE LIFT, THEN STOP, AND VERIFY DRIFT DOWN OF CYLINDERS)

NO VIBRATIONS FROM LOOSE CLAMPING, ETC.
LOWER LIFT ONTO LOCKS. VERIFY THE FOLLOWING:

ALL LOCKS ARE ENGAGING UPON DESCENT

PROPER SYNCHRONIZATION OF TRACKS
RAISE LIFT 3 INCHES, THEN LOWER VEHICLE TO FLOOR. VERIFY THE FOLLOWING:

ALL POSTS LOWERING SMOOTHLY AND ALL SYNCHRONIZED

NO LEAKS PRESENT AT ANY FITTING JUNCTIONS

NO VIBRATIONS FROM LOOSE CLAMPING, ETC.

LOCKS ARE NOT RE-ENGAGING WHILE LOWERING
ENSURE THAT ALL MANUALS AND OTHER INSTRUCTIONAL MATERIALS ARE DELIVERED TO OWNER/USER/EMPLOYER.
ENSURE THAT USERS ARE INSTRUCTED IN THE SAFE AND PROPER USER OF THE LIFT.
THIS ENDS THE FINAL CHECKOUT OF LIFT.
File: Final Checkout MP-Series.doc
12
AUTOMOTIVE LIFT SAFETY TIPS
Post these safety tips where they will be constant reminder to your lift operator.
For information specification to the lift, always refer to the lift manufacturer’s manual
1. Inspects your lift daily. Never operates if it malfunctions or if it has broken or damaged parts. Repairs
should be made with original equipment parts.
2. Operating controls are designed to disengage when released. Do not block closed or override them.
3. Never overload your lift. Manufacturers rated capacity is shown on nameplate affixed to the lift.
4. Positioning of the vehicle and operation of the lift should be done only by trained and authorized
personnel.
5. Never raise vehicle with anyone inside it. Customers or bystanders should not be in the lift. During
operation.
6. Always keep lift area free of obstructions, grease, tools, trash and other debris.
7. While working under the vehicle, lift should always be set on mechanical locking devices.
8. Note that with some vehicles, the removal (or installation) of components may cause a critical shift in the
centre of gravity and results in raised vehicle instability. Refer to the vehicle manufacturer’s service
manual for recommended procedures when vehicle components are removed.
9. Before lowering lift, be sure tool trays, stands, etc. are removed from under the vehicle. Release locking
devices before attempting to lower lift.
10. Before removing vehicle from lift area, remove posts to provide and unobstructed exit .
These “Safety Tips” along with “Lifting it Right” a general lift safety manual, are presented as an industry
service by the Automotive Lift Institute. For more information on this topic, writes to ALI, PO Box 85,
Cortland, NY 13045
13
MAINTENANCE INSTRUCTIONS
1. The channel sections where the carriage bearings ride against should be cleaned and lubricated twice a
year (once every 6 months) using a light lubricant (WD-40). The channel sections where the slide
blocks ride against should be cleaned and lubricated twice a year (once every 6 months) using a light
lubricant (WD-40).
2. The main carriage bearings are factory lubricated and do not require any additional periodic
lubrication. However, if additional lubrication is desired on these under the customer’s own inspection
and maintenance program, it is recommended to use CAM2 – Multipurpose #2 Grease (Part No.
86035) or equivalent. Use approximately 2 oz. per bearing.
3. Weekly, or whenever the hoist is used after any extended down time, the communication cables
should be checked to make sure that there are no nicks or cuts which may reduce or compromise the
insulation. Use a de-greasing cleaner to clean all cables so they maintain their visibility (Ensure cables
are disconnected when cleaning them and do not spray cleaner on end connections). Also, check
visually the hydraulic line connections for leaks and tighten or repair as necessary.
4. Check your hydraulic fluid annually. Every five years the hydraulic fluid should be changed using new
Dexron III ATF. Drain the reservoir tank only when the carriage is in the lowered position. Fill with
3.25 US gallons per reservoir.
5. Every three months check snap rings on wheels and carriage lock. Apply a light coating of lubricant
to pins as needed (WD-40).
6. In case of electrical break down have qualified service personnel service the lift using only factory
direct replacement parts.
7. Call your Distributor or Factory direct if you have any questions with regards to operating the lift or
need of replacement parts.
NOTE:
ONLY TRAINED LIFT SERVICE PERSONNEL ARE PERMITTED TO
REPLACE WORN OR BROKEN PARTS.
REPLACE FAULTY PARTS WITH GENUINE MOHAWK RESOURCES LTD.
FACTORY DIRECT PARTS ONLY.
14
EXPLANATION OF COMPUTER SYSTEM
SYSTEM ACTIVATION
All posts on this system are identical (there is no master or slave columns). After the posts are connected as
described in the lift setup, the lift is ready to be activated. As each post is turned on, they “search” for each
other, establishing a shared network for synchronizing and controlling the lift as a system.
The first thing the user must do to operate the lift is to verify that the network is detecting the desired number
of columns to use. Pressing the selection key arrow to the right of “YES” will allow the user to begin raising
and lowering the lift.
Example Screen shows lift with 4 posts present in system, Post
#1, #2, #3, and #4. Pressing the right selection key arrow will
activate lift.
Post presence will be affected by how many posts are
connected in the system, if they are connected properly (see
lift setup), if the dummy plugs are connected properly (see lift
setup), and if they are turned on (to “Operate Lift”).
OPERATION OF SYNCHRONIZED LIFTING OR LOWERING
Each PLC (programmable logic controller) is “addressed” which establishes its identity on the network. For
example, post #1 has a PLC with address #1, etc. Once communication of the network of PLCs is established,
each PLC senses control and position inputs from each other. Be aware that pairs are designated as post #1&2,
post #3&4, post #5&6, and post #7&8, regardless of where they are physically placed in the system.
The height of each carriage above floor level is measured by string potentiometers (see next section) and
compared to the other carriages by the PLC network. During raising, if any one carriage position is more than
1” higher than the lowest carriage, the higher (fastest) one slows down or stops to allow the lowest (slowest)
one to catch up. During lowering, if any one carriage position is more than 1” lower than the highest carriage,
the lower one slows down or stops to allow the highest one to catch up. This is all done by shifting motor
contactors and lowering solenoid valve.
When lifting in Pair or Single mode, counting is not done, resulting in the PLC’s seeing a “synchronized”
state after this adjustment is made. There are limits on how far the lift will allow a Single post to raise/lower,
and how far a Pair of posts can raise/lower relative to the rest of the system.
If you turn off the unit or press the Emergency Stop button, the computer position for each column is still
retained and the columns will still maintain synchronized relative positions.
15
FUNCTION OF STRING POTENTIOMETER (String-Pot)
There is a string potentiometer (string-pot) mounted on the top of each column, and connected to each
carriage, which senses the movement of the carriage. The string-pot sends an absolute analog (4-20mA) signal
to the PLC as the string is pulled in and out of the sensor. This signal is absolute, which means that the lift
will always know the height of the lift, even when powered off and on again. This signal is directly translated
into height position and can be witnessed by viewing the Post Height Screen, F2. If raising or lowering is not
possible, manually pulling the string-pot cable, while the unit is powered and pressing F2, will enable you to
see the height changes.
FUNCTION MENUS
The control screen has 10 function keys that will display various menus. They are as follows:
F1: Post ID and Active Posts Display
This screen will display the Post ID and all the active posts of the
system it is connected to.
i.e. The display to the left shows post #2 connected in a 4-post
system manner with posts #1, 2, 3, & 4.
F2: Post Height Display
This screen will display the current post height in inches.
i.e. The display to the left shows the post at a height of 42 inches.
(Note the tolerance of +/- ½ inch)
16
F3: Weight Display
This screen will display 1 of 3 screens, depending if the lift has the hydraulic pressure sensing option present.
If all the posts in the system have the pressure sense option, the screen (A) will display showing the weight on
the post and the total weight of the system. If only the present column has the pressure sense option, then
screen (B) will display, showing only the post weight. If you are at a column that does not have a pressure
sense option, then screen (C) will display. (Note the tolerance of +/- 3% in weights shown)
Refer to F9 for factory settings enabling and disabling the pressure sense option in each post.
A
B
C
F4: Voltage Display
This screen will display the current voltage (VDC) of the battery
system.
i.e. The display to the left shows the post at 23.05 VDC.
(Note the tolerance of +/- 0.5 VDC)
17
F5: User Settings Display
This screen displays general user settings of the lift. Pressing enter and the up or down arrow keys will scroll
through this menu. Press Escape and the Exit Key to Exit Menu. Item shown in this menu are as follows:
Post ID
Post Capacity
Serial Number
Maximum Height Limit
Warranty Expiration Date
Lifting Cycles Used
F7: Maintenance/Service Display
(Distributor or Factory Password Protected)
This screen displays general service and inspection information and
service contact information. Distributor or Maintenance personell
password required. (See F10).
F8: Configuration Settings (Factory Password Protected)
This screen displays configuration settings for the battery voltage
monitoring, string-pot height sensor, and the pressure sensor. This
is only accessible with the factory password (See F10).
18
F9: Factory Settings (Factory Password Protected)
This screen displays factory settings. This is only accessible with
the factory password (See F10).
F10: Password
This screen allows entry of the password which will give access to
the PLC configuration settings and screens F9 and F10. Enter either
the Distributor Password to give limited access to F7 screen, or the
Factory Password to give access to all password protected screens.
ERROR MESSAGES:
The following are a list of error messages that may display if certain situations arise.
Post Count Error:
This screen appears if the user says “NO” to the initial Active Posts
response screen.
(See System Activation above)
19
Comms Lost Error:
This screen appears if any column in the system is lost after it was
previously present. This could be due to a column being turned off
or if the communications to the post are not connected. The post in
which communications is lost will be identified on the screen. All
controls will be locked-out until this is remedied.
i.e. The display to the left shows loss of communications to post 3.
E-Stop Error:
If any post in the system has an Emergency Stop button pushed, this
screen will appear showing which post was stopped. All controls
will be locked-out until this is remedied.
i.e. The display to the left shows the emergency stop button pushed
on post 2.
Lift at Max Height Error:
Indicates that a post has raised to the maximum height setting (set
in the factory setting menu). The post that has reached this height
will be identified. Raising and parking are not allowed in this
situation, only lowering. (Note that the max height setting is
adjustable for buildings with low clearance, etc..)
i.e. The display to the left shows that post 4 has reached max
height.
20
Maximum Offset Error:
There are limits on how far any post can be out of level from any other post, even when using Single and Pair
overrides. If any post reaches its limits, one of the following screens will be displayed (depending on if the
unit is being used in All, Pair, or Single). The highest and lowest posts will be identified. Raising is only
allowed on the lowest post, Lowering only allowed on the Highest post. These offsets are normally outside
the bounds of normal usage and prevent extreme out of level conditions.
Lock Not Releasing Error:
This screen will only occur during Lowering of the lift. This screen
indicates that one of the locks is not released, and it will prevent the
lift from lowering. This may be due to a lock on the identified post
from being mechanically parked, the solenoid not pulling the lock
back, or the sensor not “seeing” the lock pulled back (sensor may
need to be adjusted). The post that causes this error will be
identified.
i.e. The display to the left shows that post 1 lock is not released.
Loss of Motion Error:
This screen will occur if any post is not sensing motion when a
raise or lowering command is present. This may occur if a post
string-pot is disconnected, malfunctioning, or cable is broken. This
also may occur if the lift is lowering onto an obstruction to prevent
its motion. Press Exit key at post this occurs at to remove message.
(Note: If message remains, then the string-pot is disconnected and
needs to be repaired)
i.e. The display to the left shows that post 4 experienced a loss of
motion while raising or lowering.
21
Post Overload Error: (Optional)
This screen will appear if any post has a weight on it that exceeds
the capacity of the post. Post capacities are set in the factory setting
menu. Raising and parking are not allowed in this situation, only
lowering. (This error will only be present if the lift has the pressure
sensing option.)
i.e. The display to the left shows that post 3 & 4 are overloaded.
Battery Warning:
This indicates that one of the post’s batteries are low on charge and
need to be recharged. (Also, refer to battery meter above control
screen.) Pressing the “OK” button will allow lift function, but only
for a few cycles until the “Battery Low” error occurs (see below).
i.e. The display to the left warns that post 6 battery is low.
Battery Low Error:
This indicates that one of the post’s batteries is too low on charge
and needs to be recharged. The lift will not function until this post
is fully recharged.
i.e. The display to the left shows that post 6 battery is low and lift
will not function until post 6 is fully recharged.
22
TROUBLE SHOOTING
NOTICE: Read manual prior to trouble shooting. A good understanding of how this lift
and its controls function will greatly help in understanding any problems that may
occur.
START-UP:
Problem: Upon power up, screen does not illuminate (on any single column).
Solution1: Verify that power cables are unplugged from charger inlets on all posts. Post will not power up
unless power is removed from charger.
Solution2: Check to see that battery cables are connected to batteries properly. Also verify 24 VDC at the
control panel.
Solution3: PLC may have faulty screen. Consult Mohawk Service department.
Problem: All posts are not shown on activation screen.
Solution1: Verify that all posts in system are turned on to “Operate Lift”.
Solution2: Check for proper communication cable and dummy plug connection of all posts. (See lift setup)
Solution3: Possible faulty communication cable or dummy plug. Consult Mohawk Service department.
Problem: Error Code present.
Solution: See Error Code Section in this manual.
DURING OPERATION:
Problem: Error Code present.
Solution: See Error Code Section in this manual.
Problem: There is more than 1-1/2” height difference between carriages.
Solution: This may be due to the fact that one column was operated on SINGLE before operating the unit in
the ALL mode. This may also be due to operating in the PAIR mode before operating in ALL mode.
Problem: Lift jack not raising lift or lift jack not collapsing when loaded.
Solution1: Lift jack relief valve needs to be adjusted. Turn relief set screw clockwise to increase lifting
ability of jack. Turn relief set screw counter-clockwise to reduce lifting ability of jack. See illustration in
back of manual.
23
Solution2: Jack is low on oil. Add oil. (Dexron III AFT or equivalent)
Problem: Carriage is lowering on its own.
Solution1: Check that there are no oil leaks by checking around the column. If so, repair the leak condition.
Solution2: If Solution 1 does no produce results, check for leakage of cylinder piston seals. Remove black
plastic vent tube from power unit reservoir tank port and see if any fluid is flowing out. If so, cylinder piston
seals are leaking. Contact Mohawk’s Service department.
Solution3: If Solution 2 does not produce results, the lowering valve(s), located on the power unit may have
collected some dirt, preventing them from sealing properly. Make sure that the carriage is lowered to floor
level in order that there is no pressure in the system. Disconnect the power so that no one can start the unit.
You can now remove the lowering valve(s). Disconnect the electrical leads from the solenoid using a
screwdriver to remove the screw holding the two mating connectors. Remove the lowering valve(s) from the
power unit and check to see that there is no foreign material in the valve ends, which prevent the balls from
sealing. Remove the foreign material. If you cannot find any problem, replacement of valve may be
required. Contact Mohawk’s Service department.
Solution4: If Solution 3 does not produce results, the power unit’s main load holding check valve may have
collected some dirt, preventing it from sealing properly. Make sure that the carriage is lowered to floor level
in order that there is no pressure in the system. Disconnect the power so that no one can start the unit. You
can now remove the check valve components and check to see if there is any foreign material in the valve
cavity to prevent the ball from sealing. Remove the foreign material. If you cannot find any problem, reseating of the valve, or replacement of valve may be required. Contact Mohawk’s Service department.
24
MODEL:
SERIAL NUMBER:
DATE OF INSTALLATION:
SERVICE CHART
DATE
PART REPLACED / SERVICED
SERVICE
COMPANY
SERVICED BY
MAINTENANCE CHART
DATE
MAINTENANCE PERFORMED
25
SERVICE
COMPANY
SERVICED BY
MOHAWK
PARTS
MP-18-24VDC-SERIES
ELECTRIC/HYDRAULIC
PORTABLE LIFT
26
MOHAWK
ILLUSTRATIONS
MP-18-24VDC-SERIES
ELECTRIC/HYDRAULIC
PORTABLE LIFT
28
Charger Status Lights:
Each post comes equipped with a dual battery charger which provides charging for two 12 VDC
batteries (in series makes 24 VDC). Each charger is rated for 120 VAC, 60 Hz, 4 Amp draw. Keep
this in mind if using extension cords and multiple adapters into a single outlet. (4 chargers will draw
4 x 4 amps = 16 amps total). There are three charging levels that the charger progresses through to
full charge. Refer to the MINN KOTA MK220D manual enclosed at end of this manual. Bank 1
Refers to battery on the left (as viewed from the control box), Bank 2 is battery on the right (under
the charger).
Note that to protect the charger, the lift will not function when power is supplied to the charger
receptacle. Once power is supplied to charger receptacle, “Power On” light illuminates on charger
and lift control panel will power.
Bulk Charging Mode: Each bank will show Solid Yellow Lights. (charger delivers full current to
batteries until they reach ~75% charge)
Absorption Charging Mode: Each bank will show Flashing Yellow Lights. (charging current
tapers down while battery voltages held at 14.4V at 77DegF.)
Maintenance / Float Charging Mode: Each bank will show Flashing Green Lights. (charger
voltage dropped to 13.4V per bank to maintain full charge on battery)
Ready: Each bank will show Solid Green Lights. (batteries have been in maintenance mode for
more than 24 hrs).
Any Red Light would indicate error in charging. Consult charger section for details.
NOTE: Avoid halting charging cycle until batteries are fully charged (this may decrease the life and
charge holding capacity of the batteries). Do not recharge fully charged batteries. Status of left
battery may differ from status of right battery. Wait until both batteries are fully charged prior to
using lift.
29
Battery Status Indicator:
The front panel of each post has a battery level indicator which shows the current charge of the
batteries. (Battery level is also available by pressing the F3 button.) Be aware that the lower the
battery level is, the higher the amp draw, and thus the deeper the level of charge drawn by the
batteries. Paying attention to these meters and using a regular recharge routine will provide the
user with years of trouble free usage.
Battery Full: This shows the battery at fully energized state. When depleted, the battery level
meter will only “reset” to full after the battery has been fully charged.
Battery Low: (Both lights alternate flash). This shows the battery at 80% discharge. Use of the
lift below this level may damage the batteries. The controls on this unit will prevent the lift from
operating at this level, and give the user plenty of warning before approaching this discharged state.
30
Jack Operation:
Prior to moving
posts, the rear
jack wheels must
be engaged. To
do this, push black
lever down, then
jack handle to
desired height.
When post is
in position,
collapse jack
wheel fully by pulling
black lever up.
Jack Relief Adjustment:
If jack does not
collapse under
load or if jack does
not raise back of post
onto wheel, then the
relief valve may need
to be adjusted. To set
proper jack capacity, lift
empty post with jack,
then remove relief port cap
with 5mm allen wrench (see
location to right). Using
5mm allen wrench SLOWLY
turn adjustment screw counterclockwise until jack collapses.
Then screw in clockwise
1 full turn. Replace port cap.
31
24 VDC MASTER ENCLOSURE:
MAIN CONTROL PANEL – Showing controls for Raise, Lower, Park, Single/All/Pair, and
Emergency Stop. Battery Level Gauge and Lift Display also present.
Left Side of Control Box
Right Side of Control Box
MASTER ENCLOSURE PORTS:
1. COMMUNICATION RECEPTACLE – Place where communication cable or dummy
plug connects.
2. 12 VDC AUXILIARY POWER RECEPTACLE – Provided to plug in standard electrical
items that run on 12 VDC, (i.e. Lights)
3. HORN – Sounds when mechanical locks are released. Volume is adjustable.
4. PENDANT RECEPTACLE – Place where hand pendent connects.
5. COMMUNICATION RECEPTACLE CAP – Can also be used to hold spare dummy
plugs.
6. OPERATE LIFT/CHARGE LIFT SWITCH – Turns on Power to post. When post power
is turned off, charging is enabled.
7. 120 VAC CHARGER POWER INLET – Connecting a 120 VAC Power Cord to this
inlet provides power to the dual battery charger.
MASTER ENCLOSURE COMPONENTS (DOOR):
PLC (Programmable Logic Controller) – “Computer” that provides logic to the entire
system, controlling all inputs and outputs, and networking with all other posts in the
system. The orange strip is all the Inputs and the black strip is all the outputs.
Communications are branched off the bottom of the PLC to both sides of the box to
allow connectivity to other PLC’s in the system.
MASTER ENCLOSURE COMPONENTS (PANEL):
1.
2.
3.
4.
5.
6.
7.
8.
MAIN POWER SWITCH – Turns on Power to the post.
MAIN POWER FUSE – 200 Amp rated to protect the whole electrical system, and
sized to accommodate the motor amperage.
CONTROL CIRCUIT BREAKERS – One protects the PLC and the raising/lowering
solenoids. A separate breaker protects the Lock Solenoid.
24 VDC (+) TERMINAL BLOCKS – Provide distribution for the +24 VDC.
24 VDC (-) TERMINAL BLOCKS – Provide distribution for the -24 VDC.
INPUT/OUTPUT TERMINAL BLOCKS – Provide distribution to several inputs and
outputs.
LOCK RELEASE RELAY (24 VDC) – When energized, will divert power to lock
release solenoid.
CHARGER RELAY (120 VAC) – Energizes when charger is supplied power (120
VAC) and prevents lift from running when lift is charging.
COMMUNICATION CABLE:
This is a DEVICENET network cable that is 10 meters long (32’-10” Long) with male ends.
This cable is readily available from a variety of electrical suppliers that deal in network
components.
DUMMY PLUGS:
Place male dummy plugs into opposite ends of post system at unused communication ports.
MOHAWK
SCHEMATICS
MP-18-24VDC-SERIES
ELECTRIC/HYDRAULIC
PORTABLE LIFT
34
MOHAWK
CHARGER INFORMATION
MP-18-24VDC-SERIES
ELECTRIC/HYDRAULIC
PORTABLE LIFT
35
OWNER’S MANUAL FOR
MINN KOTA ONBOARD
BATTERY CHARGERS
Models: MK110D,MK210D,
MK220D, MK315D, MK330D
Service Information:
Please call our service department
at 800-227-6433 if you have any
problems with your battery charger.
A technical support representative
will be happy to assist you.
Compliant with FCC
PART 15,Class B
1. SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS!
This manual contains important safety and operating instructions applicable to the safe and efficient use of your Minn Kota battery charger.
The Minn Kota battery charger is a powerful electrical device. If incorrectly installed, configured or operated, the battery charger can damage batteries and / or electrical equipment. Please read thoroughly the instructions and safety information contained in this manual before operating the
battery charger.
WARNING: RISK OF EXPLOSIVE GASES
WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS DANGEROUS. BATTERIES CONTAIN SULFURIC ACID AND PRODUCE
EXPLOSIVE GASES. A BATTERY EXPLOSION COULD RESULT IN LOSS OF EYESIGHT OR SERIOUS BURNS. FOR THIS REASON, IT
IS OF UTMOST IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS EACH TIME YOU USE THE CHARGER.
TO REDUCE THE RISK OF BATTERY EXPLOSION, FOLLOW THESE INSTRUCTIONS AND THOSE PUBLISHED BY THE BATTERY MANUFACTURER FOR ANY EQUIPMENT YOU INTEND TO USE IN THE VICINITY OF THE BATTERY. REVIEW CAUTIONARY MARKINGS ON
THESE PRODUCTS AND ON ENGINE, MOTOR OR OTHER EQUIPMENT REQUIRING BATTERY USAGE.
Use of an attachment not recommended or sold by Johnson Outdoors Inc. may result in risk of fire, electric shock, or injury to persons or property.
The charger is not intended for use by young children or infirm persons without supervision. Young children should be supervised to ensure that they do not play
with the charger.
To reduce risk of damage to electric plug or cord, pull by the plug rather than the cord when disconnecting the battery charger.
An extension cord should not be used unless absolutely necessary. Use of the improper extension cord could result in a risk of fire or electric
shock. If extension cord must be used, make sure:
a) That pins of plug of the extension cord are the same number, size and shape of those of the plug on the battery charger;
b) That extension cord is properly wired and in good electrical condition;
c) That wire in extension cord is proper size as follows:
Minimum recommended AWG wire size for various length extension cords used with the Minn Kota
battery charger:
Length of Cord in feet
AWG Size
25
16
50
14
100
12
Do not operate the battery charger with a damaged cord or plug.
Do not operate the battery charger if it has received a sharp blow, been dropped or otherwise damaged in any way.
Do not disassemble the charger. Incorrect reassembly may result in a risk of electric shock or fire.
To reduce risk of electric shock, unplug the charger from outlet before attempting any maintenance or cleaning. Disconnecting the leads will not
reduce this risk.
To reduce to risk of shock or spark, never touch the ring terminals together while the charger is plugged into an outlet or extension cord.
External connections to the battery charger shall comply with the United States Coast Guard electrical regulations (33CFR183, Sub Part 1).
2. PERSONAL PRECAUTIONS
Consider having someone close enough nearby to come to your aid when you work near a lead acid battery.
Have plenty of fresh water and soap nearby in case battery acid contacts skin, clothing or eyes.
Wear complete eye protection and clothing protection. Avoid touching eyes while working near battery.
2
If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with running cold water
for at least 10 minutes and get medical attention immediately.
Never smoke or allow a spark or flame in vicinity of battery, engine, motor or other flammable or explosive equipment.
Be extra cautious to reduce risk of dropping a metal tool onto battery. It might spark or short circuit battery or other electrical part that may
cause explosion.
Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead acid battery. A lead acid battery can
produce a short circuit current high enough to weld such items, causing severe burns.
Use the Minn Kota battery charger for charging and maintaining FLOODED / WET CELL, MAINTENANCE FREE, AND AGM / STARVED ELECTROLYTE batteries only. It is not intended to supply power to low voltage electrical systems other than for charging and maintaining batteries.
Do not use the charger for charging dry-cell batteries that are commonly used with home appliances. These batteries may burst and cause
injury to persons and damage to property.
NEVER charge a frozen battery.
3. PREPARING TO CHARGE
1) If necessary to remove battery from boat or vehicle to charge or maintain, always remove grounded terminal from battery first (if applicable).
Make sure all accessories in the boat or vehicle are off, so as not to cause an arc.
2) Be sure area around battery is well ventilated while battery is being charged or maintained.
3) Clean battery terminals. Be careful to keep corrosion from coming in contact with eyes.
4) Add distilled water in each cell until battery acid reaches level specified by battery manufacturer ONLY AFTER the battery has been charged.
Adding water to a discharged battery may result in acid leaking out of the battery and causing injury to persons and damage to property. Do not
overfill. Study all battery manufacturers’ specific precautions; however, make sure to REPLACE ALL CELL CAPS after refilling so that water
evaporation is avoided. Water will evaporate over time if cell caps are not replaced after refilling. For a battery without removable cell caps,
such as valve regulated lead acid batteries, carefully follow manufacturer’s recharging instructions.
NOTE: The battery fluid level should be checked every 30 days
5) Study all battery manufacturers’ specific precautions while charging and recommended rates of charge.
4. DC CONNECTION PRECAUTIONS
1) The Minn Kota charger will only charge 12 volt 6 cell lead acid batteries. Do not connect the output of the charger to any other voltage or
type of battery.
2) The charger’s DC output terminals are designed to be permanently mounted and connected to batteries.
3) Connect and disconnect DC output terminals only after removing the AC plug from the electric outlet.
4) The charger output leads must be connected with the correct polarity for the charger to function. The RED lead must be connected to the
POSITIVE terminal of the battery and the BLACK lead must be connected to the NEGATIVE terminal of the battery. See section 6 under
“CONNECTING THE BATTERIES TO THE CHARGER” for proper connection procedure.
5. GROUNDING AND AC POWER CORD CONNECTION INSTRUCTIONS
The Minn Kota battery charger should be grounded to reduce risk of electric shock. The charger is equipped with an electric AC power cord with
a grounded plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
DANGER – Never alter AC cord or plug provided – if it will not fit outlet, have proper outlet installed by a qualified electrician. Improper connection can result in a risk of an electric shock.
CAUTION – To reduce risk of fire or electric shock, connect battery charger directly to grounding receptacle (three-prong). An adapter should
not be used with battery charger.
3
6. INSTALLING THE BATTERY CHARGER
CHOOSING THE MOUNTING LOCATION:
For optimum performance, the charger should be mounted flush on a bulkhead in a protected area away from rain or spray. Do not mount the
charger above batteries as lead-acid batteries give off corrosive gasses which will damage the charger over time. Never allow battery acid to
drip on charger when reading electrolyte specific gravity or filling battery. Also, as with most electrical devices, do not mount the charger below
the waterline of the boat or directly adjacent to fuel tanks.
Each DC output cord is 6 feet long. Make sure that all DC output cords can reach the batteries and that the AC power cord can reach a power
source. When using an extension cord, make the AC connection to the charger outside of the battery compartment as far away as practical to
reduce the risk of a spark igniting gasses in the compartment.
Each output cord is equipped with a temperature sensor. By monitoring external temperature, the battery charger adjusts the charging profile of
the battery to assure full charge without overcharging or undercharging the battery. Attempting to lengthen or shorten the output wires could
damage the temperature sensor and affect the charger output.
If the DC battery leads are not long enough, they may be lengthened by splicing and soldering 12 AWG (minimum) wire. Each splice should be
covered with dual wall adhesive lined heat shrink tubing to protect the joint from corroding. The splice should be made between the fork in the
output cable and the fuse holder. The fuse holder should always remain within 7” of the battery terminals. The maximum extension length is 15
feet. You may contact the Minn Kota Service Department with any questions. Do not splice the AC power cord, as this voids the three year
Limited Warranty.
Even though the Minn Kota charger is capable of operating in a high ambient temperature environment, a minimum of 6 inches of unobstructed
area should be allowed on all sides of the unit for proper air circulation and cooling. Proper cooling and circulation will allow the charger to operate at peak efficiency.
MOUNTING THE CHARGER:
Due to the weight of the charger and the pounding that boats routinely endure, take the time to securely mount the charger to prevent damage.
Mounting with bolts, nuts, and washers is preferable to mounting with screws. Use the largest diameter bolts possible, and use all four mounting
holes.
Your battery charger is supplied with an AC plug holder designed to hold the power cord plug when not in use. Mount the AC plug holder with
four screws in a convenient dry site to prevent corrosion to the AC plug and to prevent the AC plug from making contact with the battery posts.
CAUTION – Because the body of the battery charger is metallic, do not directly mount the charger to the hull of an aluminum boat. Use a
means of isolation (such as wood or plastic) to prevent the charger body as well as mounting fasteners from coming in contact with the aluminum boat structure or hull. Doing so will eliminate any risk of electrolysis that may occur when AC power is connected to the charger.
WARNING – MAKE SURE THE CHARGER IS DISCONNECTED FROM AC POWER BEFORE CONNECTING THE BATTERIES TO THE
OUTPUT CORDS.
CAUTION - Before making any connections to batteries in a confined space (such as a battery compartment of a boat), open the door or hatch
of the compartment and allow it to air out for 15 minutes. This allows any gasses that have accumulated in the compartment to escape.
CONNECTING THE BATTERIES TO THE CHARGER:
FOLLOW THESE STEPS WHEN THE BATTERY CHARGER IS INSTALLED IN A BOAT OR VEHICLE. A SPARK NEAR THE BATTERY MAY
CAUSE BATTERY EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR THE BATTERY:
1. Position AC and DC cords to reduce risk of damage by hood, door, or moving engine parts.
2. Stay clear of fan blades, belts, pulleys and other parts that can cause injury to persons.
3. Check polarity of battery posts. POSITIVE (POS, P, +) battery post is usually larger in diameter than NEGATIVE (NEG, N, -) post.
4. Determine which post of the battery is grounded (connected) to the chassis (if any). If negative post is grounded to the boat hull or chassis
(as in most vehicles), see (5) below. If positive post is grounded to the boat hull or chassis, see (6) below. If neither is grounded, the order in
which the output leads are connected does not matter.
5. For negative-grounded boat or vehicle, connect POSITIVE (RED) output terminal to POSITIVE (POS, P, +) ungrounded post of battery first.
Then connect NEGATIVE (BLACK) output to NEGATIVE (NEG, N, -) grounded post of battery.
6. For positive-grounded boat or vehicle, connect NEGATIVE (BLACK) output to NEGATIVE (NEG, N, -) ungrounded post of battery first. Then,
connect POSITIVE (RED) output terminal to POSITIVE (POS, P, +) grounded post of battery.
7. When disconnecting charger, disconnect AC power cord from electric outlet first.
8. When disconnecting output terminals from battery posts, always do so in reverse sequence of the connecting procedure while as far away
from battery as practical.
4
FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE BOAT OR VEHICLE. A SPARK NEAR BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE THE RISK OF A SPARK NEAR BATTERY:
1. Check polarity of battery posts. POSITIVE (POS, P, +) battery post is usually larger in diameter than NEGATIVE (NEG, N, -) post.
2. Connect POSITIVE (RED) output terminal to POSITIVE (POS, P, +) post of battery.
3. Connect NEGATIVE (BLACK) output terminal to NEGATIVE (NEG, N, -) post of battery.
4. Do not face battery when making final connection.
5. When disconnecting charger, disconnect AC power cord from electric outlet first.
6. When disconnecting output terminals from battery posts, always do so in reverse sequence of the connecting procedure while as far away
from battery as practical.
7. A marine (boat) battery does not need to be removed and charged on shore. However, instructions must be followed for location of charger
when permanently mounted or used on board.
Each output bank is independent and isolated from one another and the AC input. The Minn Kota charger can charge independent batteries or
combinations of batteries hooked in series or parallel without disconnecting the batteries from any switches or wires / straps joining the batteries.
See diagram on page 8.
7. OPERATING INSTRUCTIONS
Make sure the charger is properly mounted and the DC output cords are connected properly to the batteries. Double check the polarities of the
output cords and make sure the correct bank of the charger is connected to the correct battery.
INDICATOR LIGHTS:
To begin charging, connect the charger to AC power. All lights will turn on momentarily. The following will be displayed on the charger:
A GREEN power light is lit to indicate AC power is applied. Each bank has YELLOW, GREEN, and RED lights to indicate charging status and
error conditions.
Minn Kota's Multi-Stage Charging has three modes of operation that deliver a fast, precise charge profile by automatically controlling current and
voltage without overcharging your batteries.
Stage 1: Bulk Mode
During this stage, the charger delivers full current until the battery reaches ~75% charge. A YELLOW light is lit for each bank to indi
cate the battery is charging in the Bulk Mode.
Stage 2: Absorption Mode
The charging current tapers down while the battery voltage is held at 14.4V at 77°F. A flashing YELLOW light is lit for each bank to
indicate the battery is charging in the Absorption Mode.
Stage 3: Maintenance Mode
When the battery reaches full charge, the charger voltage is dropped to 13.4V at 77°F. A flashing GREEN light is lit for each bank to
indicate the battery is in Maintenance Mode and ready to use. After 24 hours, the charger automatically turns off and a GREEN light is
lit for each bank to indicate the battery is in long term Maintenance Mode and ready to use. The charger will automatically turn on
when the battery voltage drops below 12.6V.
5
Error Conditions:
1) A RED light for each bank is lit if any of the following apply:
a) No battery is connected to an output cord. This may also indicate a blown fuse in the fuse holder.
b) The battery is connected reverse polarity.
c) A short circuit.
d) The battery voltage is below 4 volts. The bank will not charge a battery in this condition. (see note below)
e) The battery voltage is above 18 volts. The bank will not charge a battery in this condition.
2) A flashing RED light is lit for each bank if there is a damaged temperature sensor on the output cord. The bank will not operate if
this occurs.
3) Flashing RED and GREEN lights are lit for each bank if any of the following apply:
a) The battery voltage does not rise above 10.5V after 3 hours. The battery may be damaged and will not be charged.
b) Charging in Bulk Mode exceeds 20 hours. The battery may be damaged and will not be charged
NOTE – A 12 volt battery with an open-circuit voltage below 4 volts has either been discharged to the point of internal damage, may be heavily
sulfated, or may have internal shorted cells. Attempting to charge a battery in this state is dangerous. The battery should be replaced.
CAUTION – If a RED light is lit, disconnect the AC power from the charger immediately. Determine the reason based on the above information
and take the necessary corrective action to remedy the situation. If you are unable to remedy the situation and need help, call the Minn Kota
Service Department at 1-800-227-6433 and a technical support representative will be happy to assist you.
CAUTION – We recommend that you not recharge your battery, (or batteries), with the watercraft or motor lower unit in the water during electrical
storms. Severe damage to the motor or charging system may occur if lightning strikes nearby or if storm related high voltage conditions exist.
CAUTION – Generators with a modified square wave output can damage this MINN KOTA charger. Generators with a sine wave output can be
used to power this charger.
WARNING – TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT PERFORM ANY SERVICING OTHER THAN THOSE CONTAINED IN THE
OPERATING INSTRUCTIONS.
INLINE FUSE:
Each output cord has inline fuses on the RED and BLACK leads located near the ring terminals. These fuses serve as protection from
surges and short circuits caused by a damaged charger output cable. If a fuse blows, replace it with the exact type and rating of the original
fuse. Improper battery connections will normally not cause a fuse to blow since this is handled by the chargers internal circuitry.
8. MAINTENANCE / CLEANING / STORAGE INSTRUCTIONS
Check battery charger for dirt, oil, battery corrosion, etc. Use a water and baking soda solution for cleaning corrosion. Wipe clean using a
dry cloth.
Check ring terminals for dirt, oil, and battery corrosion; then disconnect from battery posts and clean as necessary with water and baking
soda solution and dry with a clean cloth.
When the charger is not in use, coil the power cord to prevent damage.
If power cord or plug becomes damaged, you may contact the Minn Kota Service Repair Department for service repair information. Otherwise, dispose of the battery charger in compliance with local law. Damaged cords and plugs can cause electric shock or electrocution.
When storing the battery charger, store in a clean dry area.
NOTE – This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION – Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
6
9. TROUBLESHOOTING
PROBLEM:
Check Connection (Red) light comes on.
SOLUTION:
-Check polarity of leads to battery.
-Check connetions to battery and fuses in output cord.
-Check voltage at battery. The bank will not charge a battery below 4 volts or above 18 volts.
-If still not working, call the Minn Kota Service Department at 1-800-227-6433.
PROBLEM:
Check Connection (Red) light is flashing.
SOLUTION:
-The temperature sensor in the output cord is damaged. Check to make sure the output cord is not damaged. If the output cord was
extended, check to make sure the procedure in Section 6 was followed.
-If still not working, call the Minn Kota Service Department at 1-800-227-6433.
PROBLEM:
Indicator lights will not illuminate.
SOLUTION:
-Check the AC power at the outlet.
-Make sure the GFCI(Ground Fault Circuit Interrupter) o the outlet has not tripped.
-Check the AC power at the end of the extension cord.
-If still not working, call the Minn Kota Service Department at 1-800-227-6433.
PROBLEM:
The red and green lights are flashing.
SOLUTION:
-Check to make sure there are not any loads on the battery
-Check the fluid in the battery and add fluid if necessary.
-If the voltage of the battery does not increase above 10.5 volts after 3 hours or does not increase to the absorption voltage of 14.4 volts in 20 hours, then
the bank will shut down and will not charge. The battery should be tested.
-If still not working, call the Minn Kota Service Department at 1-800-227-6433.
Specifications:
Model
MK110D
MK210D
MK220D
Part No. System Volts Banks
1821105
1822105
1822205
MK220DS 1822204
10
12 / 24
2
10
3
5
12 / 24
MK330DS 1823304
12 / 24 / 36
1823305
5
1
12 / 24 / 36
MK330D
Total Output
(amps)
12
12 / 24
1823155
MK315D
Output per
Bank (amps)
12 / 24 / 36
2
2
3
3
10
10
10
10
Input Cable
10
18AWG - 6'
20
18AWG - 6'
20
18AWG - 6'
18AWG - 8.5'
15
18AWG - 6'
30
18AWG - 8.5'
30
18AWG - 6'
Output Cable
Size L x W x H
Weight
(lbs)
Input Current
(120VAC, 60Hz)
11-1/2" x 7-1/2" x 4"
11
2.5A
16AWG - 6'
10-1/2" x 7-1/2" x 4"
16AWG - 6'
13-1/2" x 7-1/2" x 4"
15
16AWG - 6'
12-1/2" x 7-1/2" x 4"
14
2.7A
20
5.2A
16AWG - 6'
16AWG - 6'
16AWG - 6'
16AWG - 6'
13-1/2" x 7-1/2" x 4"
16-1/4" x 7-1/2" x 4"
16-1/4" x 7-1/2" x 4"
10
15
20
2.5A
4.4A
4.4A
5.2A
7
TWO CHANNEL
BATTERY CHARGER
SINGLE CHANNEL
BATTERY CHARGER
120V AC
INPUT
120V AC
INPUT
BLACK-
BLACK-
RED+
12v battery
RED+
12v battery
BLACK-
RED+
NOTE: If batteries are connected in
series for 12/24 - 24V, the series
connection wire should be left in
place during charging.
12v battery
THREE CHANNEL
BATTERY CHARGER
120V AC
INPUT
BLACK-
RED+
12v battery
8
BLACK-
RED+
12v battery
BLACK-
RED+
12v battery
NOTE: If batteries are connected in
series for 12/24 - 24 - 24/36 - 36V, the
series connection wire should be left
in place during charging.
This page provides Minn Kota® WEEE compliance disassembly instructions. For more
information about where you should dispose of your waste equipment for recycling and
recovery and/or your European Union member state requirements, please contact your
dealer or distributor from which your product was purchased.
Tools required but not limited to: Flat Head screw driver, Phillips screw driver, Socket
set, Pliers, wire Cutters..
9
MOHAWK
BATTERY INFORMATION
MP-18-24VDC-SERIES
ELECTRIC/HYDRAULIC
PORTABLE LIFT
36
AGM Features –
Deka’s AGM (Absorbed Glass Mat) Series uses a special absorbed
electrolyte technology that is superior to conventional lead-acid batteries.
This completely sealed valve-regulated battery line eliminates gas emissions
and acid leakage for longer and safer battery operation.
How AGM Works
Unlike conventional “flooded” lead-acid batteries, AGM sealed valve-regulated technology eliminates the need to add water because the oxygen and
hydrogen gases react to maintain the necessary amounts of moisture. Highly
porous microfiber separators wrapped around the positive plates completely
absorb and trap the electrolyte,
so there is no excess to spill or
POSITIVE PLATE
leak out of the battery. Oxygen
NEGATIVE
formed from the positive plates
PLATE
during charging passes horizontally through the separator
pores to the negative plates,
CONTROLLED where it reacts with hydrogen
PRESSURE
and changes back to water to
replenish the electrolyte.
O2
LE
AD
SEPARATOR
NEGATIVE PLATE
SEPARATOR
RECYCLE
POSITIVE PLATE
Oxygen diffuses through the horizontal separator pores
to the negative plate as this is the only available path.
“POWERED
N
CONTROLLED
PRESSURE
UR
T
RE
Pb
UL Recognized
Component
MH17218
QUALITY SYSTEM
CERTIFIED
ISO 9001
ISO/TS 16949
■ Specially-engineered safety relief valve
system effectively controls critical internal gas pressure, preventing capacity loss
from excessive gas seepage. This one-way
valve also prevents outside air from entering
the battery–a common cause of failure in
most sealed valve-regulated battery designs.
■ Fine microfiber glass separators are
highly porous to hold electrolyte more
efficiently and have extremely low electrical
resistance for higher capacity.
■ Power path grids are computer-cast and
pasted to uniform thickness, allowing for
the exact degree of compression needed for
optimum oxygen flow between the plates and
separators. (Plates compressed too tightly
will impede oxygen flow, while plates packed
too loosely allow valuable oxygen to escape
to the top of the battery. Both conditions
seriously impair performance and shorten
battery life.)
■ Exclusive individual plate formation
provides the highest quality and most
consistent performance.✝
AGM Benefits –
■ Maintenance-free construction eliminates
the need to add water.
■ Completely sealed valve-regulated design
eliminates acid spills and terminal corrosion.
■ Safer operation substantially minimizes
chance of acid spray, fumes and explosion
hazards when charged correctly.
■ Flexible design can be installed in almost
any position. (However, upside-down
installation is not recommended.)
■ State-of-charge easily determined
by open circuit voltage.
■ Lower electrical resistance provides
higher discharge rates.
■ High freeze-resistance offers longer
battery life.
■ Resists vibration damage for longer
operating time.
■ Lightweight construction for
easy installation.
■ Requires less charging time than
conventional batteries.
ENVIRONMENTAL
SYSTEM CERTIFIED
ISO 14001
FOR PERFORMANCE”®
Lyon Station, PA 19536-0147 • Phone: 610-682-6361 • Fax: 610-682-4781
Order Department Hotline: 610-682-4231
www.dekabatteries.com • e-mail: [email protected]
DISTRIBUTED BY:
ABSORBED GLASS MAT SERIES
Deka AGM Series (Absorbed Glass Mat)
for longer and safer battery operation
®
ABSORBED GLASS MAT SERIES
MINUTES DISCHARGED AT*
GROUP
NO.
U1
22NF
24
27
31
4D
8D
GC2
GROUP
NO.
U1
22NF
24
27
31
4D
8D
GC2
PART
NO.
FOOTNOTES
8AU1
8AU1H
8A22NF
8A24
8A24NH
8A27
8A31DT
8A4D
8A8D
8AGC2
50
AMPS
25
AMPS
15
AMPS
8
AMPS
5
AMPS
5
MINS.
STARTING OR DEEP-CYCLE – EV – TROLLING MOTOR – WHEELCHAIR
2,38,39,Y
10
20
54
98
200
340
110
75
60
2,17,38,39,Y
10
20
54
98
200
340
110
75
60
2,38,39,G
22
40
102
180
365
620
160
120
95
2,17,38,39,G
35
60
150
280
550
900
220
165
130
2,38,39,G
35
60
150
280
550
900
220
165
130
2,17,38,39,G
43
75
185
330
640
1080
270
200
153
2,16,17,U
53
87.4
200
348
706
1265
305
226
174
2,17
106
180
413
745
1512
2507
508
408
318
2,17
138
230
517
953
1874
3040
600
475
386
2,G
94
171
409
718
1409
2304
—
—
—
8AU1
8AU1H
8A22NF
8A24
8A24NH
8A27
8A31DT
8A4D
8A8D
8AGC2
PART
NO.
75
AMPS
DISCHARGE AMPS PER 12-VOLT BATTERY
TO 1.75 VPC @ 80°F (27°C)*
10
15
20
30
60
MINS.
MINS.
MINS.
MINS.
MINS.
V
O
L
T
S
AMPERE HOUR CAPACITY*
100
HR.
20
HR.
8
HR.
STARTING OR DEEP-CYCLE
12
37.0
32.0
29.5
12
37.0
32.0
29.5
12
63.0
55.0
50.0
12
91.0
79.0
72.0
12
91.0
79.0
72.0
12
100.0
92.0
84.0
12
110.0
105.0
90.0
12
210.0
198.2
176.0
12
250.0
245.0
212.0
6
220.0
187.0
173.7
5
HR.
LENGTH
– EV – TROLLING MOTOR
27.5
23.0
24.0 (10.9)
27.5
23.0
24.0 (10.9)
46.5
35.5
38.5 (17.5)
69.2
50.5
53.0 (24.0)
69.2
50.5
53.0 (24.0)
78.0
59.0
63.0 (28.6)
86.0
68.2
69.0 (31.3)
164.0
115.0
129.0 (58.5)
197.0
151.1
158.0 (71.7)
163.0
102.6
69.5 (32.0)
FOOTNOTES:
2 - Black cover / Gray case
16 - Dual terminal universal design
17 - Includes handle
38 - “Non-Spillable” defined by DOT (Department of
Transportation) definition
39 - “Non-Spillable” defined by ICAO (International
Commercial Airline Organization) and IATA
(International Airline Transportation Association)
definitions
B - Flag terminal w/ 3/8" diameter hole
G - Offset post w/ horizontal hole, stainless steel 5/16"
bolt & hex nut
U - Molded-in offset SAE post and vertical
5/16" NEG., 3/8" POS. stainless steel
studs & locking hex nuts
Y - Small L terminals with round holes
WIDTH
– WHEELCHAIR
(197) 51⁄8
73⁄4
85⁄16 (211) 51⁄8
93⁄8
(238) 51⁄2
107⁄8 (276) 63⁄4
101⁄4 (260) 63⁄4
123⁄4 (324) 63⁄4
1215⁄16 (329) 63⁄4
203⁄4 (527) 81⁄2
203⁄4 (527) 11
101⁄4 (260) 71⁄8
39
39
62
85
85
98
114
200
256
—
23
23
35.5
50.5
50.5
59
68.2
115
151
—
16
16
28
36
36
44
49.0
85
106
—
STANDARD/OPTIONAL
TERMINALS
MAXIMUM OVERALL DIMENSIONS
INCHES (MM)
APPROX.
WEIGHT
LBS. (KGS.)
1
HR.
50
50
80
110
110
130
147
266
325
—
90
MINS.
HEIGHT
(130)
(130)
(140)
(171)
(171)
(171)
(171)
(216)
(279)
(181)
71⁄4
71⁄4
91⁄4
97⁄8
97⁄8
97⁄8
93⁄8
10
10
107⁄8
(184)
(184)
(235)
(251)
(251)
(251)
(238)
(254)
(254)
(276)
B
G
U
Y
Warranty void if opened or improperly charged. Caution: Constant under- or overcharging will
damage any battery and shorten its life. Use a good constant potential, voltage-regulated charger.
For 12-volt batteries, charge to at least 14.4 volts but no more than 14.6 volts at 68°F (20°C).
For 6-volt batteries, charge to at least 7.2 volts but not more than 7.3 volts at 68°F (20°C). Do
not charge in a sealed container. The AGM Series has more capacity at high discharge rates than
conventional deep cycle batteries.
Shown is the
constant charging
voltage in relation
to the ambient
temperature for
cyclic and float use.
Constant Voltage vs. Temperature
* Nominal
All batteries are manufactured in polypropylene cases.
✝ Excludes Group U1
Capacity vs. Operating Temperature
[%]
1xI 20
100
90
Percent of Available Capacity
Potential Applications of AGM
Starting, Lighting and Ignition
Cars • Trucks • Marine • Snowmobiles
Lawn & Garden Tractors
Traction
Wheelchairs • Floor Sweepers • Guided Vehicles
Small Fork Lifts • Trolling Motors
Industrial
Cable TV • Emergency Lighting • Exit Lighting
Alarm and Security Systems • PBX Systems • Utility Control
Switching Equipment • Medical Equipment
Recreational Vehicles • Electronic Cash Registers
Portable Devices
Construction Equipment • Portable Pumps and Generators
Portable Test and Measuring Equipment
Portable Tools • Mobile TV, VCR, VTR
4xI 20
80
70
60
20xI 20
50
40
30
20
10
-30
-22
-20
-4
-10
14
0
32
+10
50
+20
68
+30
86
+40
104
+50 [°C]
122 [°F]
Shown are the changes in
capacity for a wider ambient
temperature range, giving
the available capacity as
a percentage of the rated
capacity at different ambient
temperatures, for three
different load examples,
with uninterrupted discharge
to the appropriate discharge
cut-off voltage. The values
for the upper edge of the
curve were obtained from
charging at an ambient
temperature of +20°C (68°F)
with a voltage limit of 2.3
V/cell. For the lower edge,
charging was carried out at
the specified ambient temperature. The curves show
the behavior of the battery
after a number of cycles.
Ambient Temperature
E.P.M. Form No. 0151 Rev. 5/10
© 2010 by EPM Printed in U.S.A.
All data subject to change without notice.
No part of this document may be copied or reproduced, electronically
or mechanically, without written permission from the company.
TECHNICAL MANUAL
Valve-Regulated Lead-Acid (VRLA):
Gelled Electrolyte (gel) and Absorbed Glass Mat (AGM) Batteries
EAST PENN Expertise and American Workmanship
Quality System Certified to ISO 9001
Introduction
• is non-spillable, and therefore can be operated in virtually any
position. However, upside-down installation is not recommended.
Valve-regulated lead-acid (VRLA) technology encompasses both
gelled electrolyte and absorbed glass mat (AGM) batteries. Both types
are valve-regulated and have significant advantages over flooded leadacid products.
* Connections must be retorqued and the batteries should be cleaned periodically.
What is an AGM battery?
An AGM battery is a lead-acid electric storage battery that:
More than a decade ago, East Penn began building valve-regulated
batteries using tried and true technology backed by more than
50 years experience. East Penn’s unique computer-aided manufacturing expertise and vertical integration have created a product that is
recognized as the highest quality, longest lived VRLA battery
available from any source.
• is sealed using special pressure valves and should
never be opened.
• is completely maintenance-free.*
• has all of its electrolyte absorbed in separators consisting
of a sponge-like mass of matted glass fibers.
• uses a recombination reaction to prevent the escape of
hydrogen and oxygen gases normally lost in a flooded
lead-acid battery (particularly in deep cycle applications).
• is non-spillable, and therefore can be operated in virtually
any position. However, upside-down installation is not
recommended.
East Penn’s gel and AGM batteries are manufactured to tough quality
standards. East Penn manufactures high power gel and AGM batteries
with excellent performance and life.
Applications
VRLA batteries can be substituted in virtually any flooded lead-acid
battery application (in conjunction with well-regulated charging), as
well as applications where traditional flooded batteries cannot be
used. Because of their unique features and benefits, VRLA batteries
are particularly well suited for:
* Connections must be retorqued and the batteries should be cleaned periodically.
How does a VRLA battery work?
A VRLA battery is a “recombinant” battery. This means that the
oxygen normally produced on the positive plates of all lead-acid
batteries is absorbed by the negative plate. This suppresses the
production of hydrogen at the negative plate. Water (H2O) is
produced instead, retaining the moisture within the battery.
It never needs watering, and should never be opened as this
would “poison” the battery with additional oxygen from the air.
Opening the battery will void the warranty.
Deep Cycle, Deep Discharge Applications
•
•
•
•
•
Marine Trolling
• Electronics
• Sailboats
Electric Vehicles
• Wheelchairs
• Golf Cars
Portable Power
• Floor Scrubbers
Personnel Carriers
• Marine & RV House Power
Commercial Deep Cycle Applications
Standby and Emergency Backup Applications
• UPS (Uninterrupted Power Systems)
• Emergency Lighting
• Computer Backup
• Telephone Switching
• Village Power
What are the differences between gel
batteries and absorbed glass mat
(AGM) batteries?
• Cable TV
• Solar Power
Unusual and Demanding Applications
• Race Cars
• Off-road Vehicles
• Marine & RV Starting
Both are recombinant batteries. Both are sealed valve-regulated
(SVR) – also called valve-regulated lead-acid (VRLA). AGM batteries
and gel batteries are both considered “acid-starved”. In a gel
battery, the electrolyte does not flow like a normal liquid.
The electrolyte has the consistency and appearance of petroleum
jelly. Like gelled electrolyte batteries, absorbed electrolyte batteries
are also considered non-spillable – all of the liquid electrolyte is
trapped in the sponge-like matted glass fiber separator material.
• Air-transported Equipment
• Wet Environments
• Diesel & I.C.E. Starting
What is a gel battery?
A gel battery is a lead-acid electric storage battery that:
The “acid-starved” condition of gel and AGM batteries protects
the plates during heavy deep-discharges. The gel battery is more
starved, giving more protection to the plate; therefore, it is better
suited for super-deep discharge applications.
• is sealed using special pressure valves and should never be
opened.
• is completely maintenance-free.*
• uses thixotropic gelled electrolyte.
• uses a recombination reaction to prevent the escape of
hydrogen and oxygen gases normally lost in a flooded
lead-acid battery (particularly in deep cycle applications).
Due to the physical properties of the gelled electrolyte, gel battery
power declines faster than an AGM battery’s as the temperature
drops below 32ºF. AGM batteries excel for high current, high power
applications and in extremely cold environments.
1
What is the difference between VRLA
batteries and traditional wet batteries?
Can our VRLA batteries be used as
starting batteries as well?
Wet batteries do not have special pressurized sealing vents, as they
do not work on the recombination principle. They contain liquid
electrolyte that can spill and cause corrosion if tipped or punctured.
Therefore, they are not air transportable without special containers.
They cannot be shipped via UPS or Parcel Post or used near
sensitive electronic equipment. They can only be installed “upright.”
Our VRLA batteries will work in SLI (Starting, Lighting and Ignition)
applications as long as the charging voltage is regulated to the
appropriate values from the tables on page 11. Many vehicle
regulators are set too high for gel batteries; therefore, the charging
system may require adjustment to properly recharge a gel battery
for best performance and life.
Wet batteries lose capacity and become permanently damaged if:
AGM batteries excel in low temperature, high current applications
such as cold weather starting.
• left in a discharged condition for any length of time (due to
sulfation). This is especially true of antimony and hybrid types.
• continually over-discharged, due to active material shedding.
This is especially true of automotive starting types.
What do the ratings and specifications
signify for this line?
Our gel cells have triple the deep cycle life of wet cell antimony alloy
deep cycle batteries, due to our unique design. The shelf life of a
VRLA battery is seven times higher than the shelf life of a deep cycle
antimony battery.
All ratings are after 15 cycles and conform to BCI specifications.
CCA = Cold Cranking Amperes at 0°F (–17.8°C)
Cold cranking amperes equal the number of amperes a new, fully
charged battery will deliver at 0°F (–17.8°C) for thirty seconds of
discharge and maintain at least 1.2 volts per cell (7.2 volts for a
12-volt battery).
How do VRLA batteries recharge?
Are there any special precautions?
CA = Cranking Amperes at 32°F (0°C)
While our VRLA batteries accept a charge extremely well due to their
low internal resistance, any battery will be damaged by continual
under- or overcharging. Capacity is reduced and life is shortened.
Same as above, tested at 32°F (0°C).
Overcharging is especially harmful to any VRLA battery because of
the sealed design. Overcharging dries out the electrolyte by driving
the oxygen and hydrogen out of the battery through the pressure
relief valves. Performance and life are reduced.
The reserve capacity is the time in minutes that a new, fully charged
battery can be continuously discharged at 25 amperes and maintain
at least 1.75 volts per cell (10.5 volts for a 12-volt battery).
RC = Reserve Capacity at 80°F (27°C)
Minutes discharged at 50, 25, 15, 8 and 5 Amperes
If a battery is continually undercharged, a power-robbing layer of
sulfate will build up on the positive plate, which acts as a barrier
to recharging. Premature plate shedding can also occur.
Performance is reduced and life is shortened.
Minutes discharged is the time in minutes that a new, fully charged
battery will deliver at various currents and maintain at least 1.75
volts per cell. These are nominal or average ratings.
Therefore, it is critical that a charger be used that limits voltage.
The charger must be temperature-compensated to prevent underor overcharging due to ambient temperature changes. (See Charging
Voltage vs. Ambient Temperature chart on page 11.)
Ampere Hour Capacity at 20, 6, 3 and 1 Hour Rates
Important Charging Instructions
EXAMPLE
10 amperes for 20 hours (10 x 20) = 200 Ah @ the 20-hour rate
8 amperes for 3 hours (8 x 3) = 24 Ah @ the 3-hour rate
30 amperes for 1 hour (30 x 1) = 30 Ah @ the 1-hour rate
Therefore, if you have an application that requires a
draw of 17 amperes for 3 hours, you would need a 51
Ah battery (@ the 3 hour rate)…(17 x 3 = 51). However,
this is 100% of the capacity of this 51 Ah battery.
Ampere hour capacity is a unit of measure that is calculated by
multiplying the current in amperes by the time in hours of discharge
to 1.75 volts per cell. These are nominal or average ratings.
The warranty is void if improperly charged. Use a good constant
potential, temperature-compensated, voltage-regulated charger.
Constant current chargers should never be used on VRLA batteries.
Can VRLA batteries be installed in
sealed battery boxes?
Most system designs will specify a battery that will deliver a
minimum of twice the capacity required. This means the battery
will discharge to 50% of its capacity. Using a 50% depth of
discharge (versus 80% or 100%) will dramatically extend the life
of any battery. Therefore, when helping to specify a battery for a
system, choose a battery with at least twice the capacity required
for best performance. If 50 Ah is required, specify at least a 100 Ah
battery.
NO! Never install any type of battery in a completely sealed
container. Although most of the normal gasses (oxygen and hydrogen) produced in a VRLA battery will be recombined as described
above, and not escape, oxygen and hydrogen will escape from the
battery in an overcharge condition (as is typical of any type battery).
For safety’s sake, these potentially explosive gasses must be allowed
to vent to the atmosphere and must never be trapped in a sealed
battery box or tightly enclosed space!
2
CHART A
Independent Laboratory Testing BCI 2-Hour Life
Group Size “27” Batteries East Penn Gel and AGM vs. Competitor
This chart compares the cycles run until the battery capacity dropped to 50% of
the 15th cycle’s capacity (on discharges at the 2-hour rate to a 10.5-volt cutoff).
East Penn AGM
East Penn Gel
CHART B
Charging Current vs.Charging Time
Shown is the current needed to charge a battery from 0% to 90% state of charge
in a given time. Or time required to change a battery from 0% to 90% state
of charge at a given current. For example, to charge an 8G8D (curve H) to 90% in
3.5 hours, 100 amperes are required; at 35 amperes, it would take 10 hours
Initial Charging Current (Amperes)
H
F, G
A 8GU1, 8GU1H, 8AU1, 8AU1H
B 8G22NF, 8A22NF
C 8G24, 8A24
D 8G27, 8A27
E 8G30H, 8G31, 8G31DT, 8A30H, 8A31, 8A31DT
F 8GGC2, 8AGC2
G 8G4D, 8A4D
H 8G8D, 8A8D
E
D
C
B
A
Hours
3
CHART C
VRLA Battery Voltage During Constant Current Discharge
Battery Voltage
Voltage vs. Percent Discharged
CHART D
Gel Percent Cycle Life vs. Recharge Voltage
This chart shows the effect on life of overcharging a gel battery.
(e.g.: Consistently charging at 0.7 volts above the recommended level reduces life by almost 60%!)
% of Cycle Life (B.C.I. RV/Marine)
Percent Discharged
Recharge Voltage (12-volt Battery)
4
What are the features and benefits that
make East Penn’s VRLA batteries unique?
Exclusive Computerized Gel Mixing
Proper gel mixing is critical to life and performance. Consistency in
mixing means consistent reliability. We have designed and built the
newest, state-of-the-art gel battery manufacturing facility in the world.
An example is our proprietary computerized gel mixing operation.
East Penn Expertise
East Penn builds VRLA batteries to the highest standards. Our manufacturing process features improved controls using state-of-the art
computers and the latest manufacturing technology and equipment.
Therefore, the VRLA batteries produced by East Penn consistently
meet the highest quality performance and life standards.
Our exclusive formula is mixed using computer control in every stage
of the process. Computer control delivers superior consistency for
gel battery performance that is unequaled.
Our temperature-controlled process and specially designed equipment assure a homogenous gel. It is important to note that our
equipment was designed by our engineers specifically for gel mixing…
even down to the contour of the tank bottoms and feed pipe locations. No other battery manufacturer has comparable equipment.
Ultrapremium Sealing Valve
A critical feature of any VRLA battery, gelled or absorbed, is the quality of the sealing valve. Not only must the valve keep the cell pressurized and safely release excessive pressure and gas due to overcharging, but it must also keep the cell from being contaminated by the
atmosphere. Oxygen contamination will discharge a VRLA battery
and eventually ruin the battery.
Multi-Staged Filling/Vacuuming Operation
Most other manufacturers fill their gel cells in a one step process,
vibrating the battery with hopes of releasing most of the air pockets.
This system is less than perfect and leaves voids or air pockets at
the critical gel-to-plate interface. These voids are non-reactive and
reduce overall battery performance.
Our valves are UL recognized and 100% tested after manufacturing.
The benefit is reliable performance and long life.
Spillproof and Leakproof
Our process fills and vacuums each cell several times. This multi-step
process assures complete evacuation of air and complete gel-toplate interface. Our computerized process also weighs every battery
before and after filling as a check for proper gel levels. The benefit is
more power-per-pound of battery.
A major advantage of VRLA batteries is their spillproof and leakproof
feature. However, all VRLA batteries are not created equal in their
degree of non-spillability. Some manufacturer’s AGM batteries are
unevenly filled. Over-saturation of the separators leaves liquid electrolyte that could spill. Under-saturation could lead to premature failure.
Some gels do not set properly; they remain liquid and can leak or spill.
Our AGM topping process assures that the maximum retainable electrolyte quantity is held within the battery separators, without leaving
any unabsorbed liquid to spill or leak.
Our exclusive gel electrolyte is formulated, mixed and controlled to
assure proper “set” in every battery. East Penn’s computer-controlled
gel mixing and filling equipment ensures homogenization of the mix.
This assures a gel battery that will not spill or leak. This feature allows
our gel cell to be operated in virtually any position. However, we do
not recommend an upside-down orientation.
Tank Formed Plates
East Penn is the only battery manufacturer that uses tank formation
to activate the battery plates. This process guarantees a fully formed
and voltage matched plate. The extra handling of the plates provides
an additional inspection step in the process to verify plate quality.
The AGM filling process assures that each cell is saturated with the
maximum amount of electrolyte that can be held by the separators,
without leaving excess electrolyte that could spill or leak.
Ultrapremium, Gel Glass Mat, Double Insulating Separators
Another critical component is the separator, which isolates the
positive from the negative plate. The separator must allow
maximum charge flow between the plates for maximum performance.
Separator failure is a leading cause of warranty claims
and customer dissatisfaction.
Exclusive Gel Formula
The gelled electrolyte is another critical element in this type of battery.
Our gelled electrolyte contains sulfuric acid, fumed silica, pure
demineralized, deionized water, and a phosphoric acid additive.
The phosphoric acid is a key reason that our batteries deliver
dramatically longer cycle life than leading gel competitors and
3 times longer cycle life than traditional wet cells.
East Penn uses an ultrapremium grade separator in our gel batteries. We believe that this expense (which is 5 to 6 times higher than
other types) is worth the benefits of extended life and performance:
Exclusive AGM Electrolyte
• The fiberglass mats embed themselves into the surface of
the plates, acting like reinforcing rods in concrete. This
extra reinforcement locks the active material onto the plate
for longer life and extended performance.
• The ultra-clean separators have no oil contamination
or other impurities. Therefore, resistance is low and
battery performance is high.
• Excellent porosity allows maximum charge flow,
which means more power-per-pound.
• Superior resistance to oxidation dramatically reduces
separator failure, which extends life.
• Our separators are especially suited for gel batteries,
while others use separators designed for flooded
automotive batteries.
Our AGM electrolyte contains high purity sulfuric acid and absolutely
pure totally demineralized, deionized water to increase battery
performance. Since the designs are “acid-starved” to protect the
plates from deep discharge, the acid concentration can drop to nearly
zero during an extremely deep discharge. Substances that will not
dissolve in acid may become soluble when the concentration drops
this low. Upon recharge, these dissolved substances crystallize out
of the electrolyte, potentially destroying the battery. Our electrolyte
prevents these events.
5
Ultrapremium AGM glass mat separators
loss is harmful to the battery and is evident by black posts, which
are caused by sulfuric acid fumes escaping from the battery through
and around the lead posts and bushings. These fumes can cause
corrosion and can damage sensitive electronic equipment.
Glass mat separator properties can vary considerably. East Penn
uses glass mat engineered to have an ideal balance of properties—
i.e. absorbency, compressibility, puncture resistance and electrical
resistance. This attention to detail results in high performance and
long life.
These pores and fissures are caused by the industry’s method of
casting posts and bushings. This method produces tiny air pockets
and paths which allow corrosive gas to escape, causing life shortening depressurization, cell dry-out and corrosion damage.
Exclusive Thru-Partition Weld Seals
One of the causes of self-discharge in batteries is the minute
electrical currents that flow between each cell through the partition
at the weld area. These currents accelerate the discharge of
batteries not in use.
To eliminate this problem, we use forged terminal posts and
bushings, which are completely solid with absolutely no porosity.
The benefit is longer life, better performance and no leakage of
corrosive gas…especially important when installed in or near
sensitive electronic equipment.
We block these currents by using an exclusive weld seal or gasket.
This feature dramatically reduces self-discharge to less than 3%
per month: the lowest self-discharge rate of any battery manufacturer and seven times lower than many conventional batteries!
Acid Stratification Prevention
Acid stratification can occur in conventional wet cells. During
charge, acid is released at the plate surfaces. During discharge,
acid is consumed at the plate surfaces. Since the concentration is
not uniform, diffusion (spontaneous mixing by random molecular
motions) begins. If this mixing occurred rapidly, stratification would
not occur, but it is relatively slow, allowing lighter parts of electrolyte to “float” toward the surface and heavier parts to “sink”
toward the bottom.
Exclusive Patented Calcium/Copper Lead Alloy Grids
This exclusive alloy provides longer shelf life, more powerper-pound and superior corrosion resistance. By using special
grain refiners, we can dramatically improve performance and life.
Heavy-Duty Motive Power Style Grid Design
While other manufacturers cut costs by using automotive style
grids, we use a high-performance deep cycle grid. This heavy-duty
grid design is similar to the grid in a motive power battery.
The top portion of the plates do not perform as well in contact with
lower concentration electrolyte. The bottom portion of the plates do
not perform as well with the higher concentration, and will corrode
prematurely. High voltage “equalization” charging is sometimes
used in wet batteries to make gas bubbles that re-mix the electrolyte.
The hefty “power rods” designed into our grids not only lock the
active material onto the grid, but also act as “bus bars” to collect
and direct the energy to the terminals. The benefit is more powerper-pound of battery for your equipment and longer battery life.
Because the immobilized gel will not “float” or “sink” within itself
when a non-uniform concentration exists, it cannot stratify.
Therefore, no high-voltage equalizing charge is necessary. Simply
recharge at the standard 13.8 to 14.1 voltage setting. This means
longer life and consistent performance in stationary and standby
applications.
Multiple Plate Lug Milling
Shiny, well milled plate lugs are critical to our superior cast-on-strap
quality. Each of our plate lugs is automatically milled to assure
the highest quality strap with no loose or dropped plates. Our
lugs are then fluxed and tinned automatically for an additional
assurance of quality.
Electrolyte in an AGM battery is strongly held by the capillary
forces between the glass mat fibers, but not completely
immobilized. Stratification is possible in extremely tall cells, but
cannot occur in batteries of the size covered in this document.
Heavier Plate Straps
We use an exclusive lead/tin alloy in a unique multi-stage caston-strap operation. The result is heavier straps with outstanding
lug-to-strap knit. This eliminates dropped and loose plates,
thereby improving performance and life.
Convenient Carrying Handles
Carrying handles are included on the (gel) 8GU1H, 8G24, 8G27,
8G30H, 8G31DT, 8G31, 8G4D and 8G8D models. Handles are also
available on (AGM) 8AU1H, 8A24, 8A27, 8A31DT, 8A4D and 8A8D.
This feature makes carrying, installation and removal easier,
more convenient and less time consuming.
Polyester Element Wrap
Another cause of deep-cycle battery failure is “mossing.”
This phenomenon occurs late in a battery’s life, as the positive
active material actually grows around the edge of the separator
and eventually “shorts” against the negative plate. This ends the
battery’s service life.
Dozens of Terminal Options Available
Our batteries are delivered with the most popular type of terminal;
however, on a special order basis many terminal options are
available. This gives you total flexibility to specify the proper
terminal for your application… without making compromises.
Our AGM separators wrap around the bottom of the plate and
are wider than the plates. This makes mossing failures unlikely.
To prevent life-shortening mossing in our gel batteries, we use a
special polyester fiber sheet that is wrapped around the edge of
each element, similar to the wrap in an industrial battery. The
result is longer service life.
Exclusive Forged Posts and Bushings
“Black” posts and oxygen-contaminated batteries are often due to
porous lead terminal posts. A battery can lose its critical pressure
through tiny pores and fissures in the battery terminals. Pressure
6
Proprietary Case, Cover, and Pressure Vent
State-of-the-Art Technology
We design and mold our own rugged polypropylene cases, vents
and covers in our on-site, state-of the-art plastics molding facility.
This provides ultimate control of our high performance designs,
quality and delivery to our manufacturing plant, assuring you the
highest quality battery and most reliable service.
Within our newly constructed multi-million dollar VRLA production
facility, we have incorporated state-of-the-art manufacturing
processes that are unmatched by any other battery manufacturer.
This major addition allows us to build the most modern and
reliable VRLA batteries in the industry.
Environment and Worker Protection
The designs of East Penn's VRLA batteries are always improving.
The preceding sections accurately describe East Penn's VRLA
products as of the date of publication. East Penn reserves the
right to change their processes to improve quality, value or utilize
advances in manufacturing technology. Ratings and capacities may
change without notice.
It’s nice to know that every possible safeguard was designed into
our process to protect our co-workers and the environment…
special safeguards that are exclusive to East Penn. One benefit
is assurance of a consistent source for batteries without fear of
governmental interference or delays.
Over 250 Quality Assurance Checks
Hundreds of quality checks are performed to assure total
confidence in the performance and life of our batteries.
For example:
• 100% Cycling. After initial charging, every battery
is discharged and then recharged at the factory. This
allows us to check the performance of the battery and give
it a second charge that equalizes the cells for improved
performance and longer life.
It’s interesting to note that, as a cost-saving measure, we use
the current generated during the initial discharge to recharge
other batteries in this computer-controlled process.
• Extended Shelf Stand Test. Before shipment, every
battery is required to stand for a designated period of time.
Beginning and ending voltages are compared. This extra
quality assurance step verifies that the critical pressure
control valves are functioning properly.
• Filling Weight Control. During this computerized process,
batteries are weighed before and after filling. This assures
that the exact amount of electrolyte is in each battery.
• Multi-Staged Filling and Vacuuming Process.
Every battery is filled and vacuumed several times during
this computerized process. Multi-staged vacuuming
assures complete electrolyte-to-plate interface, with no
power-robbing air pockets.
• Computerized Polarity Check. Every battery is checked by
computer for proper polarity.
• High Rate Discharge Test. Every battery is discharged at
approximately twice the rated capacity. A sensitive computer
monitors the voltage drop during this discharge to assure that
every battery performs as designed.
• Formed Element Inspection. Elements are assembled and
charged outside the battery container in a computerized
forming and drying process. This allows visual inspection of
every grid, plate, separator, and formed element before being
sealed inside the battery, assuring perfect cell elements with
longest life and highest performance.
• Tank Formed Plates. Voltage matched plates are critical
in standby applications. Forming each plate outside the
battery assures the highest quality, best matched plates
in the industry, and also allows a visual check before and
during assembly.
7
How do East Penn’s VRLA battery features
compare with other types of batteries?
FEATURE
EPM GEL
OTHER GEL
EPM AGM
0THER AGM
ALL WET
CELLS
1.
EPM Expertise
YES
NO
YES
NO
EPM ONLY
2.
Spillproof and Leakproof
YES
YES
YES
YES
NO
3.
Sealed Valve-Regulated
YES
YES
YES
YES
NO
4.
Ultra-Premium Sealing Valve
YES
NO
YES
NO
NO
5.
Exclusive Gel Formula
YES
NO
NO
NO
NO
6.
Deep Discharge Protection
YES
YES
YES
YES
NO
7.
Exclusive Computerized Gel Mixing
YES
NO
NO
NO
NO
8.
Tank Formed Plates
YES
NO
YES
NO
NO
9.
Multi-Staged Gel Filling/Vacuuming
YES
NO
NO
NO
NO
10.
Ultra-Premium Glass-Mat Dual Insulating Separators
YES
NO
NO
NO
NO
11.
Exclusive Thru-Partition Weld Seals
YES
NO
YES
NO
NO
12.
Exclusive Patented Calcium/Copper Lead Alloy Grids
YES
NO
YES
NO
NO
13.
Heavy-Duty Motive Power Style Grids
YES
NO
YES
NO
NO
14.
Grid Lug Milling, Brushing and Fluxing
YES
?
YES
NO
EPM ONLY
15.
Heavy-Duty Special Alloy Plate Straps
YES
NO
YES
NO
NO
16.
Special Polyester “Moss Guard” Element Wrap
YES
NO
NO
NO
NO
17.
Forged Posts and Bushings
YES
NO
YES
NO
EPM ONLY
18.
Acid Stratification Prevention
YES
YES
YES
YES
NO
19.
Carrying Handles
YES
?
YES
LIMITED
LIMITED
20.
Dozens of Terminal Options
YES
?
YES
?
EPM ONLY
21.
Highest Cycle Life
YES
NO
YES
NO
NO
22.
Highest Performance
YES
NO
YES
NO
N.A.
23.
Shelf Stand Test
YES
?
YES
NO
NO
24.
250+ Quality Assurance Checks w/ ISO 9001 Certification
YES
?
YES
NO
EPM ONLY
25.
State-of-the-Art Technology & Facility
YES
NO
YES
NO
EPM ONLY
8
Answers to the Most Frequently Asked Questions
NOTE: Before reviewing this section, be sure you understand the difference between gel, AGM, and flooded batteries.
How do we justify the premium price of
VRLA batteries to those unfamiliar
with this type of battery?
Absorbed Electrolyte Advantages:
•
•
•
•
•
•
•
•
•
•
•
•
•
Totally maintenance-free
Air transportable
Spillproof/leakproof
No corrosion
Installs upright or on side
Lower cost than gel cell batteries
Compatible with sensitive electronic equipment
Very low to no gassing (unless overcharged)
Excellent for starting and stationary applications
Superior for shorter duration/higher rate discharges
Superior under extreme cold conditions when fully charged
Superior shelf life
Superior rechargeability
(from 0% to 90% in 31⁄2 hours)
• Rugged and vibration-resistant
• Very safe at sea with no chlorine gas in bilge
(due to sulfuric acid and salt water mixing)
• Operates in wet environments…even under 30 feet of water
Simply review the advantages, features and benefits, performance,
and impressive life cycle results. Based upon this and the lowest
cost-per-month or duty cycle you and/or your customer should
have no trouble choosing VRLA batteries.
However, please remember that these batteries are not for
everyone or every application. Always be aware of the charging
considerations. (See pages 11 & 12.)
What are the advantages and
disadvantages of the different types
of battery designs?
Gelled Electrolyte Advantages:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Totally maintenance-free
Air transportable
Spillproof/leakproof
No corrosion
Superior deep cycle life
Installs upright or on side (side installation may lose
about 10% capacity)
Very low to no gassing (unless overcharged)
Compatible with sensitive electronic equipment
Superior shelf life
Superior rechargeability
(from 0% to 90% in 31⁄2 hours)
No recharge current limitation @ 13.8 volts
Rugged and vibration-resistant
Very safe at sea with no chlorine gas in bilge
(due to sulfuric acid and salt water mixing)
Versatile: Starting, Deep Cycle, Stationary
Operates in wet environments…even under 30 feet of water
Will not freeze to –20°F/–30°C (if fully charged)
Lowest cost-per-month (cost ÷ months of life)
Lowest cost-per-cycle (cost ÷ life cycles)
Absorbed Electrolyte Disadvantages:
• Shorter cycle life than gel in very deep cycle applications
• Automatic temperature-sensing,
voltage-regulated chargers must be used
• Water cannot be replaced if continually overcharged
• Charge voltage must be limited
(14.4 to 14.6 volts maximum at 68°F)
Flooded Electrolyte Advantages:
• Lowest initial cost
• Higher cranking amps
• Water can be added (if accessible)
• Excellent for starting applications
• Tolerant of improper recharge voltage
• Certain designs are good for deep cycle applications
• Replacements readily available
• Good under extreme cold conditions when fully charged
Flooded Electrolyte Disadvantages:
•
•
•
•
•
•
Gelled Electrolyte Disadvantages:
•
•
•
•
Higher initial cost
Heavier weight
Water cannot be replaced if continually overcharged
Automatic temperature-sensing,
voltage-regulated chargers must be used
• Charge voltage must be limited to extend life
(13.8 to 14.1 volts maximum at 68°F)
9
Spillable
Operates upright only
Shorter shelf life
Fewer shipping options
Cannot be installed near sensitive electronic equipment
Watering may be required (if accessible)
Why can’t VRLA batteries be opened?
• Our VRLA batteries are protected against deep discharge
because they are “acid-starved.” This means that the battery
uses the power in the acid before it uses the power in the plates.
Therefore, the plates are never subjected to
destructive ultra-deep discharges.
VRLA (Valve-Regulated Lead-Acid) batteries, sometimes called SLA
(Sealed Lead-Acid) batteries or SVR (Sealed Valve-Regulated)
batteries work on a recombination principle. Oxygen gas is produced at the positive plates during charge. The charged negative
plates react first with this oxygen and subsequently with the electrolyte. Water is produced and the negative plates are very slightly
discharged. Additional charging recharges the negative plates
instead of producing hydrogen gas. Since very little hydrogen and
oxygen is lost and the water (H2O) is retained, we say that the
gasses have recombined. To work properly, the oxygen produced
must be retained in the battery until the reaction is completed.
Positive pressure allows the gas to be retained.
• With proper temperature-sensing, voltage-regulated
charging (refer to table on page 11) the VRLA battery
never runs out of water.
• Our gel batteries contain ultra-premium, glass-mat,
dual-insulating separators which will not break down in
service. The glass mat embeds itself into the plate, which
retards life-shortening shedding.
• Our gel batteries contain polyester element wrap which retards
“mossing” or active material growth that causes short circuits.
If any VRLA (gelled or absorbed electrolyte) battery is overcharged,
gas will be vented from the valves. Hydrogen as well as oxygen will
be released. If continued, the electrolyte will eventually dry out and
the battery will fail prematurely. This is why charging limits are so
critical.
• Our AGM batteries contain separators at the ideal compression
and ideal saturation to achieve the best balance between capacity utilization and recombination efficiency.
• Over 250 quality control checks assure superior performance
and long battery life.
In a sealed battery a balance is maintained between the hydrogen,
oxygen and charge. If a VRLA battery is opened, or leaks, the negative plates are exposed to extra oxygen from the atmosphere.
This excess oxygen upsets the balance. The negative plates become
discharged. The positive plates may be subsequently severely overcharged. The battery will fail prematurely, and the warranty will be
voided.
Why do EPM VRLA batteries have
longer shelf life?
Our calcium/copper lead alloy premium separators and demineralized
electrolyte are ultra-pure. Impurities in the lead alloy, separators
and electrolyte cause tiny currents inside a cell which eventually
discharge the battery and shorten its shelf life. The purer the
components, the longer the shelf life. No one can match
East Penn’s purity!
Some say calcium grids don’t do well in
flooded deep cycle applications. Why does
East Penn use calcium grids in VRLA
batteries for deep cycle applications?
Our exclusive “weld seal gasket” blocks the minute cell-to-cell
currents that cause self-discharge. The better the weld seal, the
longer the shelf life. Weld seals are exclusive to East Penn VRLA
batteries.
Flooded calcium alloy makes a very efficient, low resistance battery.
Therefore, when deeply discharged, the plates release all their available power, eventually causing plate shedding and active material
fall-out. In contrast, with flooded antimony batteries, the antimony
helps lock the active material onto the grid. Therefore, the plate
does not shed as easily, which extends the deep cycle life of the
battery when compared to flooded calcium.
Does depth of discharge affect cycle life?
Yes! The harder any battery has to work, the sooner it will fail.
Our VRLA calcium alloy battery (East Penn’s exclusive patented
alloy) is also very efficient with low resistance. However, when
deeply discharged, the electrolyte is used up before the plates
are totally discharged because the battery is “acid-starved.”
This feature:
Typical* VRLA Battery Cycling Ability
vs. Depth of Discharge
Typical Life Cycles
• limits the discharge the plates can deliver.
• protects the plates from shedding due to deep discharge.
• extends the life of the battery.
Capacity Withdrawn
100%
80%
50%
25%
10%
Why do EPM VRLA batteries have
longer cycle life than others?
Gel
450
600
1000
2100
5700
AGM
150
200
370
925
3100
Some of the major features that contribute to our long cycle life are:
* You may experience longer or shorter life based upon application, charging regimen,
temperature, rest periods, type of equipment, age of battery, etc.
• Our patented calcium/copper grid alloy delivers superior
performance due to the purity of the lead. Copper is added
as a “grain refiner.” This means that the microscopic grains
in our lead grids are odd-shaped, so they retard corrosion
and extend the life of our grid.
As you can see, the shallower the average discharge, the longer
the life. This is why it’s important to size a battery system to
deliver at least twice the average power required, to assure shallow
discharges.
• Our thicker grids have more corrosion resistance than
thinner grids.
10
Follow these tips for the longest life:
• Avoid ultra-deep discharges.
• Don’t leave a battery at a low stage of charge for an extended
length of time. Charge a discharged battery as soon as possible.
• Don’t cycle a battery at a low state of charge without regularly
recharging fully.
• Use the highest initial charging current available (up to 30%
of the 20-hour capacity per hour) while staying within the
proper temperature-compensated voltage range.
Gel Charge and Float Voltages
at Various Temperature Ranges
Temp.
°F
≥ 120
110 – 120
100 – 109
90 – 99
80 – 89
70 – 79
60 – 69
50 – 59
40 – 49
≤ 39
Why can’t EPM VRLA batteries be
discharged too low?
Our VRLA batteries are designed to be “acid-starved.” This means
that the power (sulfate) in the acid is used before the power in the
plates. This design protects the plates from ultra-deep discharges.
Ultra-deep discharging is what causes life-shortening plate shedding
and accelerated positive grid corrosion which can destroy a battery.
Charge
Float
Temp.
°C
Optimum Maximum Optimum Maximum
13.00
13.20
13.30
13.40
13.50
13.70
13.85
14.00
14.20
14.50
13.30
13.50
13.60
13.70
13.80
14.00
14.15
14.30
14.50
14.80
12.80
12.90
13.00
13.10
13.20
13.40
13.55
13.70
13.90
14.20
13.00
13.20
13.30
13.40
13.50
13.70
13.85
14.00
14.20
14.50
≥ 49
44 – 48
38 – 43
32 – 37
27 – 31
21 – 26
16 – 20
10 – 15
5–9
≤4
What is acid stratification?
How do VRLA batteries prevent it?
See page 6 for a detailed explanation of this phenomenon.
Why does temperature have such
a dramatic effect on batteries?
How does a battery recharge?
The process is the same for all types of lead-acid batteries: flooded,
gel and AGM. The actions that take place during discharge are the
reverse of those that occur during charge.
Temperature is a major factor in battery performance, shelf life,
charging and voltage control. At higher temperatures there is
dramatically more chemical activity inside a battery than at lower
temperatures. The following charts graphically illustrate this fact.
The discharged material on both plates is lead sulfate (PbSO4).
When a charging voltage is applied, charge flow occurs. Electrons
move in the metal parts; ions and water molecules move in the electrolyte. Chemical reactions occur at both the positive and negative
plates converting the discharged material into charged material. The
material on the positive plates is converted to lead dioxide (PbO2);
the material on the negative plates is converted to lead (Pb).
Sulfuric acid is produced at both plates and water is consumed at
the positive plate.
100
75
50
25
% RATED CAPACITY AVAILABLE
Typical Self-Discharge of VRLA Batteries
at Different Temperatures
40°C
104°F
30°C
86°F
20°C
68°F
If the voltage is too high, other reactions will also occur. Oxygen is
ripped from water molecules at the positive plates and released as
a gas. Hydrogen gas is released at the negative plates—unless,
oxygen gas can reach the negative plates first and “recombine” into
H2O.
8°C
46°F
A battery will “gas” near the end of charge because the charge
rate is too high for the battery to accept. A temperature-compensating, voltage-regulating charger, which automatically reduces
the charge rate as the battery approaches the fully charged state,
eliminates most of this gassing. It is extremely important
not to charge batteries for long periods of time at rates which
cause them to gas because they use water, which in sealed valveregulated batteries cannot be replaced. Of course, no battery should
be overcharged for a long period of time…even at low rates using
so-called “trickle charges.”
STORAGE TIME (MONTHS)
0
3
6
9
12
15
18
21
24
27
AGM Charge and Float Voltages
at Various Temperature Ranges
Temp.
°F
≥ 120
110 – 120
100 – 110
90 – 100
80 – 90
70 – 80
60 – 70
50 – 60
40 – 50
≤ 40
Charge
Float
Optimum Maximum Optimum Maximum
13.60
13.80
13.90
14.00
14.10
14.30
14.45
14.60
14.80
15.10
13.90
14.10
14.20
14.30
14.40
14.60
14.75
14.90
15.10
15.40
12.80
12.90
13.00
13.10
13.20
13.40
13.55
13.70
13.90
14.20
13.00
13.20
13.30
13.40
13.50
13.70
13.85
14.00
14.20
14.50
Temp.
°C
In a fully charged battery, most of the sulfate is in the sulfuric acid.
As the battery discharges, some of the sulfate begins to form
on the plates as lead sulfate (PbSO4). As this happens, the acid
becomes more dilute, and its specific gravity drops as water
replaces more of the sulfuric acid. A fully discharged battery has
more sulfate in the plates than in the electrolyte.
≥ 49
43 – 49
38 – 43
32 – 38
27 – 32
21 – 27
16 – 21
10 – 16
4 – 10
≤4
The following illustration shows the relationship between specific
gravity readings and the combination of the sulfate from the acid
with the positive and negative plates at various states of charge.
11
FULLY CHARGED
Specific
Gravity
1.265
FULLY DISCHARGED
Specific
Gravity
below 1.225
Specific
Gravity
1.190
Specific
Gravity
1.120
Typical Charging Time vs. 90% and 100% State of Charge
60% of time
State of 0%
Charge
EXAMPLE:
▲
POS = PbO2
NEG = Pb
ACID = H2SO2
As battery discharges,
the sulfate from the electrolyte
forms on the plates.
▲
POS = PbSO4
NEG = PbSO4
Electrolyte = H2O
40% of time
90%
100%
31⁄2 hours
6 hours
It will take about 60% of the charge time to bring a VRLA battery
from 0% charged to 90% charged. It will take the remaining 40%
of the total charging time to put the last 10% of the charge back
into the battery.
As battery recharges,
the sulfate is driven back
into the electrolyte.
How critical is recharge voltage?
Why are all VRLA batteries so charge
sensitive?
Charge is a quantity of electricity equal to rate of flow (Amperes)
times time (hours), and usually expressed in Ampere-hours (Ah).
0% state of charge is defined as the depth of discharge giving a
terminal voltage of 10.50 Volts – measured under a steady load at
the 20-hour rate at 80ºF. (The 20-hour rate is the 20-hour capacity
divided by 20 hours.)
All lead-acid batteries give off hydrogen from the negative plate
and oxygen from the positive plate during charging.
VRLA batteries have pressure-sensitive valves. Without the ability
to retain pressure within the cells, hydrogen and oxygen would be
lost to the atmosphere, eventually drying out the electrolyte and
separators.
Typically, the charge that must be returned to a VRLA battery to
achieve a 100% state of charge is from 105% to 115% of the
charge removed.
Voltage is electrical pressure. Charge (ampere-hours) is a quantity
of electricity. Current (amperes) is electrical flow (charging speed).
A battery can only store a certain quantity of electricity. The closer
it gets to being fully charged, the slower it must be charged.
Temperature also affects charging.
Charging Guides
Typical Charge Time vs.
Initial Charge Current to 90% Full Charge
If the right pressure (voltage) is used for the temperature, a battery
will accept charge at its ideal rate. If too much pressure is used,
charge will be forced through the battery faster than it can be
stored. Reactions other than the charging reaction occur to
transport this current through the battery—mainly gassing.
Hydrogen and oxygen are given off faster than the recombination
reaction. This raises the pressure until the pressure relief valve
opens. The gas lost cannot be replaced. Any VRLA battery will dry
out and fail prematurely if it experiences excessive overcharge.
Note: It is the pressure (voltage) that initiates this problem—
a battery can be “over-charged” (damaged by too much voltage)
even though it is not fully “charged.”
(Using an automatic temperature-sensing, voltage-regulating charger
set at 13.8V. Totally discharged battery at 11.80–12.0 volts.)
Initial Amperes
Part No.
8GU1, 8GU1H, 8AU1, 8AU1H
8G22NF, 8A22NF
8G24, 8A24
8G27, 8A27
8G30H, 8G31, 8G31DT, 8A30H, 8A31, 8A31DT
8G4D, 8GGC2, 8A4D, 8AGC2
8G8D, 8A8D
This is why charging voltage must be carefully regulated and
temperature compensated to the values on page 11.
13 hrs* 6 hrs* 31⁄2 hrs*
3
5
7
8
9
17
20
8
12
17
21
24
42
50
15
23
33
41
45
83
100
*approximate
HOW TO USE THIS CHART: When charger is first turned on,
read amps after about one minute. Initial ampere reading will
indicate approximate charging time.
EXAMPLE
If an 8G24 reads about 17 ampere charge current
when first turned on, the battery will be at 90%
in about 6 hours.
How long does it take to recharge
a fully discharged VRLA battery?
A specific time is difficult to determine because recharging
depends on so many variables:
• Depth of discharge
• Temperature
• Size and efficiency of the charger
• Age and condition of the battery
IMPORTANT: Always use an automatic temperaturesensing, voltage-regulated charger! Set charger at 13.8
to 14.1 volts at 68°F for gel, or 14.4 to 14.6 volts at 68°F
for AGM. Do not exceed 14.1 volts for gel or 14.6 volts
for AGM.
See the following Charging Guides for an estimated time based
upon the initial charge current the battery accepts.
12
How can continual undercharging
harm a battery?
What is a thermal runaway?
The appropriate charge voltage depends on the battery temperature
(see page 11). A warmer battery requires a reduced voltage. If the
voltage is not reduced, current accepted by the battery increases.
When the current increases, the heating increases. This can continue in a loop feeding on itself with the battery temperature and
charging current rising to destructive levels.
In many respects, undercharging is as harmful as overcharging.
Keeping a battery in an undercharged condition allows the positive
grids to corrode and the plates to shed, dramatically shortening life.
Also, an undercharged battery must work harder than a fully
charged battery, which contributes to short life as well.
Gel batteries are much less susceptible to thermal runaway than
AGM batteries. Batteries may become more susceptible with
increasing age. Without a recombination reaction, flooded batteries
convert most excess charging energy to gas, not heat. This makes
them almost immune from the thermal runaway.
An undercharged battery has a greatly reduced capacity. It may
easily be inadvertently over-discharged and eventually damaged.
How can you tell if an
VRLA battery is fully charged?
Thermal runaway can be prevented with:
• Temperature compensation monitoring at the battery—not
at the charger.
• Limiting charging currents to appropriate levels (see page 11).
• Allowing for adequate air circulation around the batteries.
• Using timers, or Ampere-hour counters.
• Using smart chargers that recognize the signature of a
thermal runaway event which will shut the charger down.
By using a voltmeter.
Open Circuit Voltage vs. State of Charge Comparison*
%
Charge
Flooded
100
12.60 or higher
75
12.40
50
12.20
25
12.00
0
11.80
Open Circuit Voltage
Gel
AGM
12.85 or higher
12.80 or higher
12.65
12.60
12.35
12.30
12.00
12.00
11.80
11.80
How do I know if a charger is
“gel friendly” or “AGM friendly”?
NOTE: Divide values in half for 6-volt batteries.
* The “true” O.C.V. of a battery can only be determined after the battery
has been removed from the load (charge or discharge) for 24 hours.
Unfortunately, many chargers on the market claim to be gel
“friendly” or “OK for sealed batteries”, but are not. Some
overcharge the batteries, while others may not fully charge
the batteries. Some chargers claim to be “smart”. Some “smart”
chargers do a good job, others do not. The best choice of charger
often depends on the application.
How can you tell if a VRLA battery has
been damaged by under- or overcharging?
Use only “voltage-regulated” or “voltage-limited” chargers.
Standard constant current or taper current chargers must not be
used. The voltage must fall in the range of the chart on page 11.
Almost all applications require temperature sensing and voltage
compensation. Beware, many chargers measure the ambient
temperature which could be significantly different from the battery’s
internal temperature.
The only way is with a load test. Use the same
procedure you would use with a wet cell battery:
a. Recharge if the open circuit voltage is below 75%.
b. If adjustable, set the load at 1⁄2 the CCA rating or
three times the 20 hour rate.
c. Apply the load for 15 seconds. The voltage should
stabilize above 9.6 volts while on load.
Low frequency current ripple (to about 333 Hz) can be detrimental
to sealed batteries depending on the application. On applications
where the charger is connected continuously to a float voltage,
especially where simultaneous charge and discharge may occur,
the level of current ripple must be a consideration.
d. If below 9.6 volts, recharge and repeat test.
e. If below 9.6 volts a second time, replace the battery.
If you are not sure if a charger is performing properly, follow this
procedure:
What is a float charger?
What float voltage is recommended?
a. Using a fully discharged VRLA battery (OCV about 11.8V)
and a digital voltmeter, record the initial open circuit
voltage at the battery terminals.
b. Using an automatic charger as described above,
set voltage if adjustable (14.1V for gel, 14.4V for
AGM models).
c. Connect and start charging. Record initial on-charge
voltage and current .
d. Each hour or so, check and record the on-charge voltage
across the battery terminals. Except for occasional, brief
“blips” or pulses, the voltage should not exceed the voltage
limits noted in “b” above.
This type of charger continually delivers a pre-set voltage to the
battery, regardless of charge conditions.
These chargers are used in stationary, emergency back-up power,
emergency lighting, and other applications.
The frequency of discharge and temperature will dictate a more
exact setting. For example, the more frequent the discharge, the
higher the suggested recharge voltage, to a maximum of 2.35 volts
per cell (at 20°C/68°F).
Our recommended float voltage is 2.25 to 2.3 volts per cell for
gel and absorbed models.
13
e. At the end of charge (when the current is very low or goes
to zero) check and record the voltage. Note that the charger
may have turned off by then.
f. The disconnected battery should be at 100% or above after a
24 hour rest.
During the charging time, the charger should not have exceeded
the limit (except for occasional, brief pulses). This indicates that
the charger is working properly.
The valves only let gas out, never in. A partial vacuum can form
within a sealed battery under various circumstances. Battery temperature and ambient pressure play a role, but predominantly the
recombination and discharge reactions are responsible. After charging
ends, the recombination reaction continues until most of the oxygen
in the battery headspace is consumed. The total volume of the battery
components decreases slightly during a discharge. Deeply discharged
batteries often have a “sucked-in” appearance. Batteries with large
cells may display this appearance even when fully charged.
Keep in mind that the voltage limit is at 68°F/20°C. Charging at
higher or lower temperatures will change this limit.
A temperature-sensing charger should always be used, as
manual adjustments are never accurate and will damage any
VRLA battery.
If a battery bulges severely on charge, this is not normal. It is an
indication of a blocked valve or an overcharge situation. Such a
battery should be removed from service.
A sucked-in appearance can also be normal. A sucked-in battery
should be charged, but if it remains sucked-in after charging, the
appearance can safely be ignored; however, if only a single cell
displays or lacks this appearance a load test would be prudent.
Do VRLA batteries have a
“memory” like ni-cad batteries?
How safe are VRLA batteries?
Can they explode?
One of the major disadvantages of nickel-cadmium (ni-cad)
batteries is that after shallow discharge cycles, the unused portions
of the electrodes “remember” the previous cycles and are unable
to sustain the required discharge voltage beyond the depth of the
previous cycles. The capacity is lost and can only be restored by
slowly discharging completely (generally outside the application),
and properly recharging. VRLA batteries do not exhibit this
“use it” or “lose it” capacity robbing effect known as memory.
VRLA batteries are very safe, unless abused. However, as with any
type battery, certain safety precautions must be taken.
ALWAYS WEAR SAFETY GLASSES
WHEN WORKING AROUND BATTERIES!
!
What is a safe charge rate or voltage
setting for outdoor applications with wide
temperature fluctuations if a temperaturesensing charger is not available?
DANGER / POISON
SHIELD
EYES.
EXPLOSIVE
GASES CAN
NONE! As the chart on page 11 (Effect of Temperature on
Recharge Voltage) shows, charging voltage varies widely with
temperature. There is no fixed voltage setting or current that
will work. A temperature-sensing, voltage-regulated charger
must be used. Anything else will damage any battery and cause
premature failure!
CAUSE BLINDNESS
OR INJURY.
FLUSH EYES
IMMEDIATELY
WITH WATER.
NO
• SPARKS
• FLAMES
• SMOKING
SULFURIC
ACID
CAN CAUSE
BLINDNESS OR
SEVERE BURNS.
GET
MEDICAL
HELP
FAST.
KEEP OUT
OUT OF
REACHOF
OF CHILDREN.
CHILDREN.
KEEP
OFTHE
REACH
DO NOT TIP. KEEP VENT CAPS TIGHT AND LEVEL.
DO
NOT
OPEN
BATTERIES.
DO NOT OPEN FLUSH COVER BATTERIES.
CALIFORNIA PROPOSITION 65 WARNING: Batteries, battery posts,
terminals and related accessories contain lead and lead compounds
and other chemicals known to the state of California to cause cancer
and birth defects or other reproductive harm. Wash hands after
handling.
Can a VRLA battery be load tested?
Yes. See page 13 (How can you tell if a VRLA battery has been
damaged by under- or overcharging?).
Because VRLA batteries normally emit very little to no hydrogen gas,
they are safe near sensitive electronic equipment. They do not
cause corrosion of surrounding metals. No hydrogen gas means
no dangerous explosions… UNLESS SEVERELY OVERCHARGED!
Why do some VRLA batteries bulge?
Why do some VRLA batteries appear
“sucked in”? Are there visual signs of a
faulty or plugged pressure relief valve?
Do not install any lead-acid battery in a sealed container or enclosure. Hydrogen gas from overcharging must be allowed to escape.
DO NOT CHARGE IN EXCESS OF 14.1V @ 68°F - Gel Cells
DO NOT CHARGE IN EXCESS OF 14.6V @ 68°F - Absorbed
To prevent the permanent loss of gases so that recombination
has time to take place, each cell can hold up to about 1.5 psi
without venting.
Always use a reliable, temperature-sensing, voltage-regulated,
automatic charger.
Because SVR batteries have immobilized electrolyte, they cannot
spill or leak, even if punctured. That is why they are approved for air
transport by the International Commercial Airline Organization (ICAO),
International Airline Transport Association (IATA), and Department of
Transportation (DOT) as noted on the label if properly insulated from
short circuits.
Batteries with very large cells, such as the 8G4D, 8G8D, 8A4D, 8A8D
and 8GGC2, will bulge somewhat as this normal pressure builds. This
is especially true in higher temperatures, because the polypropylene
case is pliable. Therefore, a certain amount of bulge is normal.
14
Also, when protected against short circuits and securely braced/
blocked, our VRLA batteries “are not subject to any other requirements of 49 CFR Parts 171-180…” for shipping.
g. Spray exposed terminals and connectors with several coats
of battery terminal corrosion protection spray. (Mask surrounding areas to protect against overspray.)
h. For batteries which may be exposed to very wet environments
(e.g. bilge mounted batteries) total encasement of the exposed
terminals and connectors is necessary. However, do not block
or cover the vents. Allow ventilation.
A battery terminal boot should be used. Install the boot on the
cable before crimping the terminal. Fill the boot with petroleum
jelly and fit over the sprayed connectors (as in “g” above).
i. Battery charging in a boat requires a charger specifically
designed for marine applications. In addition to battery gases,
bilges often contain potentially dangerous fuel fumes.
Follow all wiring and grounding recommendations of the
charger manufacturer for on-board and on-shore connections.
Using a charger not specifically designed for marine
applications or failure to follow the marine charger
manufacturer’s grounding and wiring recommendations
could result in major corrosion damage to the hull or
prop, and create a serious risk of electrical shock or fire,
personal injury or death.
Which way does current flow? On which side
should a circuit breaker be installed?
During discharge, electrons progress through the external circuit
from the negative post toward the positive post. Inside the battery,
positive ions move toward the positive plate by diffusion where they
react, leaving neutral molecules in solution. The resulting neutral
molecules move back toward the negative plate by diffusion. There
are also negative ions in the electrolyte offsetting the positive ion
charges. Some travel by diffusion toward both the negative and the
positive plates, where they are consumed. During charge, all of the
directions reverse.
Although not physically accurate, when designing circuits or making
calculations, it is just as valid to consider positive charges moving
through the whole circuit. Indeed, this is the convention used to
define the direction of current in electronics (known as conventional
current).
Battery Installation
Proper location of disconnects depends on the application.
Vehicles can vary, but in most cases, the negative terminal is treated
as ground. The entire chassis is connected to the negative terminal
of the battery. The positive side of the circuit is considered “hot.”
Switches/circuit breakers should usually be installed on the hot
side of a device. When disconnecting the entire battery from the
system with a fusible link or circuit breaker, breaking the connection
from the negative terminal to the chassis often works best.
Note: In a multi-battery installation, it is often best to replace the
entire set of batteries when one battery is weak or has failed.
Series
A “series” system increases the voltage, but keeps the battery
capacity (cranking amps, amp hours, reserve minutes, and
minutes running time) the same. Therefore, two 12-volt
batteries connected in series (POS to NEG, NEG to POS)
will deliver 24 volts at the same rating as one battery:
During recharge, each battery receives the same amount
of current; e.g. if the charger is putting out 10 amps, both
batteries are getting 10 amps.
In multiple battery installation, there could be other considerations
such as total voltage, multiple voltages, and the effects on other
devices.
What do I need to know about
installation, especially in salt water
marine applications?
Series hookup
increases voltage…
2 x 12V = 24 Volts
Wiring and Waterproofing
ALWAYS WEAR SAFETY GLASSES
WHEN WORKING AROUND BATTERIES!
a. Cabling of the approved gauge should be tinned copper.
If using untinned copper, allow plenty of spray silicone to
“wick” along the strands.
b. Install heat-shrink tubing with a silicone interior; the silicone
forms an excellent moisture barrier. Cut the tubing long
enough to cover the terminal lug and plenty of the insulated
portion of the cable. Slip tubing onto the cable.
c. Crimp on the appropriate terminal.
d. Position the heat-shrink tubing. Heat and inspect.
e. Clean battery terminals and connect. Be sure perfect metalto-metal contact is made, with no dirt, corrosion, grease or
foreign material to interfere with current flow.
f. Always attach the cable connected to the solenoid or starter
first. Attach the ground cable last! Tighten snugly, BUT DO
NOT OVERTIGHTEN, which will damage the terminals or crack
the battery cover. This will destroy the battery and VOID THE
WARRANTY.
Parallel
A “parallel” system increases the capacity available, but keeps
the voltage the same. Therefore, two 12-volt batteries with
400 CCA, 110 R.C. and 65 Ah will deliver 12 volts, 800 CCA,
220 R.C. and 130 Ah. (Actually, since each battery’s load is
lighter, the reserve capacity will more than double.)
Parallel hookup
keeps same voltage…
2 x 12V = 12 Volts
15
To properly recharge, a sophisticated “battery isolator” should
be installed. Otherwise, one battery will be continually overcharged and the other undercharged in a dual-voltage set-up.
IMPORTANT: Do not install any type of battery in a completely sealed box or enclosure. In the event of overcharging, the potentially explosive gasses must be allowed to
escape.
During recharge, the current (amps) is split between the
batteries. The battery that is discharged the most will receive
more current than the other until both are brought up to full
charge.
Series/Parallel
A “series/parallel” system provides a combination of voltage
and capacity for special applications. Note: Never mix different
types and sizes of batteries in the same bank.
Dual Voltage
The illustration shows an arrangement that would supply
24 volts to a starter and 12 volts to the electronics (or vice versa).
12 VOLTS
24 VOLTS
Dual Voltage
hookup provides
a combination
of voltage
and capacity.
MEMBER OF:
AMERICAN BOAT
& YACHT CLUB
UL Recognized Component
INDEPENDENT BATTERY
MANUFACTURERS
ASSOCIATION
NATIONAL MARINE
MANUFACTURERS
ASSOCIATION
DISCLAIMER: By providing this information, East Penn, its employees and distributors make no representation or warranties about the information provided in this document.
All content is provided without warranties, express or implied. East Penn and its representatives are not to be held liable for any and all damages whatsoever
in using or interpreting the information in this document, whether suitable or not.
“POWERED
FOR PERFORMANCE”
TM
DISTRIBUTED BY:
Lyon Station, PA 19536-0147 • Phone: 610-682-6361 • Fax: 610-682-4781
Order Department Hotline: 610-682-4231
www.eastpenn-deka.com
E-mail: [email protected]
E.P.M. Form No. 0139 Rev. 3/04
© 2004 by EPM Printed in U.S.A.
No part of this document may be copied or reproduced, electronically
or mechanically, without written permission from the company.
16
AD
N
UR
• SPARKS
• FLAMES
• SMOKING
CAN CAUSE
BLINDNESS OR
SEVERE BURNS.
SULFURIC
ACID
GET
MEDICAL
HELP
FAST.
1. Perform a visual inspection. Inspect for defective or cracked
case and cover, and loose or damaged terminal posts
or cables. Replace battery and/ or cables immediately if any
damage is found.
Always wear safety glasses when working around batteries.
Batteries can explode! Protect your eyes.
SERVICE TIPS ..
You may have one or more of the same type or different types
on board your boat or RV. Determine which type of battery or
batteries you have and follow the correct set of instructions.
• Maintenance-Free Non-Accessible Engine Starting
with no filler caps
• Low-Maintenance Accessible Starting with filler caps
• Dual Purpose (Starting/ Cycling) with filler caps
• Deep Cycle with filler caps
The various types of batteries used in Marine and RV service are:
TYPES OF MARINE / RV BATTERIES ..
KEEP OUT OF THE REACH OF CHILDREN.
DO NOT TIP. KEEP VENT CAPS TIGHT AND LEVEL.
DO NOT OPEN FLUSH COVER BATTERIES.
OR INJURY.
CAUSE BLINDNESS
NO
FLUSH EYES
IMMEDIATELY
WITH WATER.
DANGER / POISON
SHIELD
EYES.
EXPLOSIVE
GASES CAN
!
WARNING: Batteries produce explosive gases. Keep sparks,
flames, and cigarettes away from batteries at all times.
Protect your eyes at all times. Never lean over battery when
jumping or performing other maintenance. Remember...
always wear safety glasses when working around batteries!
BE CAREFUL!..
Did you know lead-acid batteries are
Pb
virtually 100% recyclable? They have a
higher recycling rate than other waste products
RECYCLE
such as aluminum, paper, glass and plastic.
Be sure to return your lead-acid batteries to a dealer.
In most states it is illegal to discard a battery in the trash.
LE
RECYCLING IS CRITICAL..
T
RE
Specific gravity readings need to be corrected to 80ºF
(27ºC) to allow for temperature of the electrolyte and to
insure accurate readings. For each 10 degrees above
80ºF (27ºC), add four points to the hydrometer reading.
Be careful of the sulfuric acid in the battery. It can
burn eyes, clothing and damage paint and electronic
equipment. FLUSH EYES IMMEDIATELY WITH LARGE
QUANTITIES OF COOL WATER. GET MEDICAL HELP FAST.
2. Using a hydrometer: Check the state-of-charge of the
battery by taking a reading from one cell. Use a different
cell each time. If the reading is above 1.225 specific gravity,
the battery is at least 75% charged and should be OK.
If below 75%, see the Charging Tips section.
1. Using a voltmeter: Check the state-of-charge of the
battery. If the reading is above 12.4 volts, the battery
is at least 75% charged and should be OK. If below
12.4 volts, see the Charging Tips Section. Or,
• ACCESSIBLE TYPES, WITH FILLER CAPS:
1. Check the state-of-charge of the battery with a voltmeter.
If the reading is above 12.4 volts, the battery is at least
75% charged and should be OK. If below 12.4 volts,
see the Charging Tips section.
• MAINTENANCE-FREE NON-ACCESSIBLE TYPES,
WITH NO FILLER CAPS:
Always wear safety glasses when working around batteries.
Batteries can explode! Protect your eyes.
CHECK THE STATE OF CHARGE ..
Repaint hold-down, tray and surrounding parts if necessary.
3. Shine lead posts and terminal ends with a wire brush or
steel wool to clean corrosion and assure a low resistance
connection. Reassemble and coat lead parts with petroleum
jelly or a terminal protection spray.
Clean corrosion with a paste made from baking soda and
water. Apply liberally. Any corrosion is neutralized when the
solution stops bubbling. Wash off with large quantities of
water to avoid environmental damage.
2. Keep the batteries and battery compartment clean and
corrosion free. Dirty, corroded batteries can self-discharge,
which will affect performance and life.
Look for loose connections or hold-downs. Tighten snugly
if appropriate. DO NOT OVER-TIGHTEN TO AVOID BATTERY
DAMAGE!
SERVICE TIPS (continued) ..
3. If it fails a second time, replace the battery
immediately.
2. If the battery maintains a minimum "on load" voltage of
9.6 volts for 30 seconds, it is in good condition. If not,
recharge and load test again.
1. Follow the instructions on the variable load tester or ask
your favorite service dealer to load test your battery.
Using a voltmeter or hydrometer will tell you if your battery
is charged. But these tests will not indicate if a battery can
"hold a load." A battery can be fully charged, but be so weak
or worn out that it can no longer perform its function of
starting an engine or running accessory loads. Therefore,
you must also perform a load test to determine the state of
health of your battery.
Always wear safety glasses when working around
batteries. Batteries can explode! Protect your eyes.
LOAD TESTING ..
If it is not necessary to charge the battery, (or after
charging) top off by filling each cell with distilled water
to just below the filler tube in each cell.
3. Check electrolyte levels in all cells. If necessary,
add distilled water (or clear, odorless drinking water).
Do not use water with high iron content to avoid battery
damage. Never add acid, only water to a battery. If it
will be necessary to charge the battery, bring the levels
in all cells to just above the separators inside the cells to
allow for expansion during charging. Top off after charging as noted below.
If the electrolyte level is too low to read with a hydrometer, add distilled water as noted below and run the engine
or equipment at least two hours to mix the electrolyte
and avoid a false reading.
For each 10 degrees below 80ºF (27ºC), subtract four
points to the hydrometer reading. For example, at 90ºF
(32ºC) a hydrometer reading of 1.250 would be corrected
to 1.254. Likewise, at 70ºF (21ºC) a hydrometer reading
of 1.250 would be corrected to 1.246.
CHECK THE STATE OF CHARGE (continued) ..
–– FULL CHARGE
1.265 100%
1.225 75% 20 min. 35 min. 48 min.
1.190 50% 45 min. 75 min. 95 min.
1.155 25% 65 min. 115 min. 145 min.
1.120
0% 85 min. 150 min. 195 min.
90 min.
180 min.
280 min.
370 min.
––
MAXIMUM RATE @
STATE
SPECIFIC
OF
50
30
20
10
GRAVITY CHARGE AMPS
AMPS
AMPS
AMPS
NOTE:
Times are approximate and depend upon battery
condition, age and design, the efficiency of the charger,
line voltage and other factors.
12.6
12.4
12.2
12.0
11.8
BATTERY
VOLTAGE
12 VOLT BATTERY CHARGING TIME
TO FULL CHARGE @ 80°F
7. NEVER leave a battery on a trickle charger longer than
48 hours. Serious damage to the battery WILL occur.
6. NEVER attempt to charge a frozen battery. To avoid
explosion and serious injury, allow it to warm to 60°F
(16°C) before charging.
5. Stop the charge when two hydrometer or voltage readings recorded two hours apart indicate no increase.
Further charging would be useless and may damage the
battery and shorten its life. If the battery won't come up
to full charge, replace it.
4. Do not leave a battery on charge for more than 48 hours
to avoid damaging the battery by over-charging.
If gassing or spewing of electrolyte occurs, or the
battery case feels hot, reduce or temporarily halt
charging to avoid damaging the battery.
3. Unplug the charger before connecting or disconnecting
a battery to avoid dangerous sparks which can cause a
battery to explode.
2. Carefully read and follow the instructions that came with
the charger to avoid serious injury, property damage
and/or battery damage.
1. Batteries should be charged if hydrometer reading is
below 1.225 specific gravity, or open circuit voltage is
below 12.4 volts, or if the first load test is below 9.6
volts as noted previously.
Always leave filler caps in place, tight and secure to
reduce the risk of battery explosion and serious injury!
Always wear safety glasses when working around
batteries. Batteries can explode! Protect your eyes.
Do not charge batteries without proper instruction.
CHARGING TIPS ..
SELF-DISCHARGE RATE
© 2004 by EPM Printed in U.S.A.
No part of this document may be copied or reproduced, electronically
or mechanically, without written permission from the company.
E.P.M. Form No. 0273 Rev. 3/04
NOTE:
This is only an example. Self-discharge may be higher
or lower depending upon battery chemistry, lead alloys,
age and other factors.
30ºF (–1ºC) . . . . .1/10 Pt. Specific Gravity per day
50ºF (10ºC) . . . . . .1/2 Pt. Specific Gravity per day
80ºF (27ºC) . . . . . .2 Pts. Specific Gravity per day
100ºF (38ºC) . . . . . .3 Pts. Specific Gravity per day
TEMPERATURE
3. Ideally, store batteries in a cool, dry place with temperatures
not below 32ºF (0ºC) or above 80ºF (27ºC). Typically, batteries
will self-discharge at faster rates at higher temperatures.
For example:
2. Put into storage fully charged and keep them above 75%
state-of-charge. Check state-of-charge every 90 days and
recharge if necessary.
1. Disconnect the batteries to avoid self-discharge due to
parasitic loads such as clocks, ground faults, etc.
Batteries that are not in use during the off-season must be
cared for as follows to extend battery life and reliability:
OFF-SEASON STORAGE ..
www.eastpenn-deka.com
E-mail: [email protected]
Order Department Hotline: 610-682-4231
Lyon Station, PA 19536-0147
Phone: 610-682-6361 • Fax: 610-682-4781
DISTRIBUTED BY:
• DEEP-CYCLE
• DUAL PURPOSE
V
R
/
e
n
&
i
r
e
a
r
M ry Ca
e
e
c
t
n
t
Ba ntena
i
a
M
• STARTING
Batteries, battery posts, terminals and related accessories
contain lead and lead compounds, and other chemicals
known to the state of California to cause cancer and birth
defects or other reproductive harm. Wash hands after
handling.
California Proposition 65 Warning
®
– Material Safety Data Sheet –
Lead Acid Battery Wet, non-spillable (UN2800)
SECTION I
Manufacturer’s Name:
Date: January 29, 2007
East Penn Manufacturing Co., Inc.
Deka Road, Lyon Station, PA 19536
Trade Name: Gell; Absorbed Electrolyte,
Telephone Number for Information: (610) 682-6361
Sealed Valve Regulated Non Spillable Battery
Emergency Telephone Number: CHEMTREC: 1-800-424-9300, Classification: Battery wet, non-spillable, electric storage
In Washington D.C. or outside continental U.S., call 1-202-483-7616
UN2800
SECTION II
HAZARDOUS INGREDIENTS/IDENTITY INFORMATION
Hazardous Components
Specific Chemical Identity
(Common Name (s))
Lead, CAS #7439921
Sulfuric Acid, CAS #7664939
Antimony, CAS #7440360
Arsenic, CAS #7440382
Polypropylene, CAS#9003070
Calcium, CAS#7440702
Tin CAS #7440315
OSHA PEL
0.05 mg/m3
1.00 mg/m3
0.50 mg/m3
0.01 mg/m3
N/A
1.0 mg/m3
2.0 mg/m3
ACGIH TLV
0.05 mg/m3
1.00 mg/m3
0.50 mg/m3
0.01 mg/m3
N/A
1.0 mg/m3
2.0 mg/m3
Range
Percent
By Weight
60-75%
5-15%
0-0.1%
0.01 %
2-10%
0-0.1%
0-0.1%
Average
67%
10%
<0.1%
<0.1%
4%
<0.1%
<0.1%
SECTION III
PHYSICAL/CHEMICAL CHARACTERISTICS
Electrolyte (Sulfuric Acid):
Appearance and Odor: Clear, Odorless, colorless liquid
Boiling Point: 235 – 240o F
Evaporation Rate (Butyl Acetate=1): less than 1.0
Melting Point: N/A
Solubility in Water: 100%
Specific Gravity (H20=1): 1.270 – 1.330
Vapor Density (AIR=1): Greater than 1
Vapor Pressure (mm Hg): 10
SECTION IV
FIRE AND EXPLOSION HAZARD DATA
Flash Point (Method Used): Non-Flammable
Flammable Limits: *Hydrogen Gas
Extinguishing Media: Class ABC extinguisher,
LEL: 4%
UEL 74%
NOTE: CO2 may be used, but not directly on the cell. The thermal shock may cause cracking of the battery case and/or cases.
* Hydrogen gas may be generated during battery changing.
SECTION V
REACTIVITY DATA
Stability: Stable
Condition to Avoid: Prolonged overcharging, sources of ignition
Incompatibility (Materials to Avoid): Sulfuric Acid: Contact with combustibles and organic materials may cause fire and
explosion. Also reacts violently with strong reducing agents, metals, strong oxidizers and water. Contact with metals may produce
toxic sulfur dioxide fumes and may release flammable hydrogen gas.
Hazardous Decomposition of By-Products: Sulfuric Acid: Excessive overcharging or fire may create Sulfur trioxide, carbon
monoxide, sulfuric acid mist, sulfur dioxide, and hydrogen.
Lead Compounds: Contact with strong acid or base or presence of nascent hydrogen may generate highly toxic arsine gas.
MSDS: Lead Acid Battery Wet, non-spillable (UN2800) ; Page 2 of 3
SECTION VI
HEALTH HAZARD DATA
Route(s) of Entry: Not Applicable under normal use.
Carcinogenicity:
Sulfuric Acid: The International Agency for Research on Cancer (IARC) has classified “strong inorganic acid mist containing
sulfuric acid” as a Category 1 carcinogen, a substance that is carcinogenic to humans. This classification does not apply to liquid
forms of sulfuric acid contained within a battery. Inorganic acid mist (sulfuric acid mist) is not generated under normal use of this
product. Misuse of the product such as overcharging, may result in the generation of sulfuric acid mist.
Lead Compounds: Lead is listed as a 2B carcinogen, likely in animals at extreme doses. Proof of carcinogenicity in humans is
lacking at present.
Arsenic: Listed by National Toxicology Program (NTP), IARC, OSHA and NIOSH as a carcinogen only after prolonged exposure at
high levels.
Signs and Symptoms of Exposure: Avoid contact, with absorbed electrolyte (sulfuric acid) may cause irritation of eyes, nose and
throat. Contact with eyes and skin causes irritation and skin burns. Absorbed electrolyte is corrosive.
Medical Conditions Generally Aggravated by Exposure: Pregnant women and children must be protected from lead exposure.
Health Hazards (Acute and Chronic): Do not open battery, avoid contact with internal components. Internal components include
lead and absorbed electrolyte. Electrolyte is corrosive and contact may cause skin irritation and chemical burns.
Emergency and First Aid Procedures: (contact with electrolyte)
1) Flush contacted area with large amounts of water for at least 15 minutes. Remove contaminated clothing and obtain
medical attention if necessary. Eye wash and/or emergency shower should be readily available.
2) If swallowed, give large volumes of water. DO NOT induce vomiting, obtain medical treatment.
SECTION VII
PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to be Taken in Case Material is Released or Spilled: Electrolyte material is corrosive. Contains sulfuric acid. Neutralize
any spilled material. Reference 1996 North American Emergency Response Guidebook, #154.
Waste Disposal Method: Lead-acid batteries are completely recyclable. For information on returning batteries to East Penn for
recycling, contact your East Penn Representative. Dispose of any collected material in accordance with local, state or applicable
federal regulations.
Precautions to be Taken in Handling and Storing: Store away from reactive material as defined in Section V, Reactivity Data.
Place cardboard between layers of stacked batteries to avoid damage and short circuit. Do not allow metallic materials to
simultaneously contact both terminals.
Other Precautions: If battery case is broken, avoid direct contact with internal components. Keep away from ignition sources during
charging.
SECTION VIII
CONTROL MEASURES
Respiratory Protection (Specific Type): N/A
Ventilation: Must be provided when charging in an enclosed area.
Protective Gloves: Recommended
Eye Protection: Recommended
Other Protective Clothing or Equipment: N/A
Work Hygienic Practices: Good Personal hygiene and work practices are recommended.
MSDS: Lead Acid Battery Wet, non-spillable ; Page 3 of 3
SECTION IX
OTHER REGULATORY INFORMATION
NFPA Hazard Rating
Sulfuric Acid
Health (Blue)
3
Flammability (Red)
0
Reactivity (Yellow)
2
Note: Sulfuric acid is water-reactive if concentrated.
Lead
3
0
0
U.S. DOT: Batteries, wet, non-spillable, electric storage
Hazard Class/Division
ID Number
Packing Group
Label Requirements
8
UN2800
III
Corrosive
RCRA: Spent lead-acid batteries are not regulated as hazardous waste when recycled. Spilled sulfuric acid is a characteristic
hazardous waste, EPA hazardous waste number D002 (corrosivity).
CERCLA (Superfund) and EPCRA (Emergency Planning and Community Right to Know ACT)
a)
Reportable Quantity (RQ) for spilled 100% sulfuric acid is 1000 lbs.
b) Sulfuric acid is a listed “Extremely Hazardous Substance” under EPCRA with a Threshold Planning Quantity (TPQ) of 1000
lbs.
c)
Batteries are subject to EPCRA reporting requirements under sections 302/304, 311/312, and 313.
Reporting quantities are as follows:
Lead: section 311/312 = 10,000 lbs.
Title II I section 313 = 100 lbs.
Sulfuric Acid: section 311/312 = 500 lbs.
Title III section 313 = 500 lbs.
California Prop 65: Batteries, battery posts, terminals and related accessories contain lead and lead compounds, and other chemicals
known to the State of California to cause cancer and birth defects or other reproductive harm. WASH HANDS AFTER
HANDLING.
For additional information concerning East Penn Manufacturing Co., Inc. products or questions concerning the content of this MSDS
please contact your East Penn representative.
This information is accurate to the best of East Penn Mfg. Co.’s knowledge or obtained from sources believed by East Penn to be
accurate. Before using any product, read all warnings and directions on the label.
MOHAWK
OPTIONS
MP-18-24VDC-SERIES
ELECTRIC/HYDRAULIC
PORTABLE LIFT
37
CHASSIS LIFTING BEAM
See next page for chassis beam diagram and specifications.
If it is desired to raise a vehicle by the frame, this can be done by using optional chassis lifting
beams. The chassis lift beam fits into the cradle where the tire would normally fit and spans
between a pair of posts. The beam comes with lifting pads and height adapters that slide and
stack along the beam to accommodate the frame pick up points.
Directions for Use:
Drive vehicle into bay.
Roll chassis beam under desired end of vehicle where frame pick points are.
Slide pads to desired positions and stack adapters as desired to accommodate frame pick points.
Roll posts to each end of chassis beam, cradling ends of chassis beam with forks.
Lift pair until chassis beam contacts frame.
Verify proper frame engagement.
Check other posts for proper engagement of tires or frame (depending on if another chassis beam
is used or the other end is lifted by tires)
Operate lift as desired.
NOTICE:
The chassis beam is rated for 35,000 lbs total.
Always ensure that the beams are cradled in the forks as close as possible to the carriages. (Do
not place beams on tips of forks) Also, ensure that vehicle is centered on chassis beam to ensure
even loading of beam and posts.
This beam is intended to be used in conjunction with another beam or another set of mobile
column posts to lift the entire vehicle. Do not use this beam to pick up just one end of a vehicle
only. Load beam only on lifting pads, do not load beam on center.
This beam is intended for use on Mohawk MP-Series 15” Long Fork lifts ONLY.
Refer to the ANSI standard “Vehicle Lift Points for Service Garage Lifting,” ANSI/SAE J2184Oct92, safety manual “Lifting if Right,” ALI/SM01, and “Vehicle Lifting Points Guide”
ALI/LP-Guide for proper positioning of vehicles on lift.
2
WING PLOW ADAPTERS
See next page for wing plow adapter diagram and specifications.
The wing plow adapters are to be used when it is desired to raise a vehicle with side wing plows
or RV’s with side extensions where the forks are not able to get close to the tires. The wing plow
adapters are used with a pair of posts to enable lifting of the whole front axles of a vehicle by the
tires.
Directions for Use:
Drive vehicle into bay.
Roll wing plow adapters around each side of front axle tires (center tires on beam lengths).
Roll posts to each end of adapters, inserting forks fully into adapter sockets.
Lift pair until wing plow adapters engaged tires.
Verify proper engagement.
Check other posts for proper engagement of tires.
Operate lift as desired.
NOTICE:
The wing plow adapters are rated for 25,000 lbs total (per pair of beams, see spec on next page)
Always ensure that the wing plow adapters are fully inserted over the lifting forks. Also, ensure
that vehicle is centered on the wing plow adapters to ensure even loading of beams and posts.
These adapters are intended to be used in conjunction with another set of mobile column posts to
lift the entire vehicle. Do not use these to pick up just one end of a vehicle only. These adapters
are designed to lift only tires and must not be top loaded. Do not use these to pick up vehicles by
frames. Use adapters only in pairs. These adapters must not be single loaded.
The wing plow adapters are intended for use on Mohawk MP-Series 15” Long Fork lifts ONLY.
4
FORK TRUCK ADAPTERS
See next page for fork truck adapter diagram and specifications.
The fork truck adapters are to be used when it is desired to raise a fork truck by the undercarriage
for wheels free servicing. The fork truck adapters are used with a pair of posts.
Directions for Use:
Locate a pair of posts (Master and Slave) in the desired lifting location.
Assembly ramps and pads onto posts as shown in specification diagram.
Drive fork truck onto pads until center of gravity of fork truck is at center of pad.
Locate rubber blocks as desired to contact frame.
Lift pair until fork truck pad engaged fork truck frame.
Verify proper frame engagement with pads.
Lift pair approximately 6 inches verifying that truck center of gravity is centered on pad.
Shake truck slightly to ensure secure and balanced support of frame.
Operate lift as desired.
WARNING:
Any removal of components from vehicle while raised may alter the center of gravity of the
vehicle and produce an unsafe or unstable condition of the vehicle or the lifting system that may
cause injury to personnel or damage to equipment. Ensure vehicle center of gravity is always
located at center of lifting pads. Use jack stands as an added measure of safety to ensure load
stabilization.
NOTICE:
The fork truck adapters are rated for 14,000 lbs per post (28,000 lbs per post pair).
Always ensure that the fork truck adapter pads are fully inserted over the lifting forks inboard
against fork tubes. (not on tips of forks). Also, ensure that fork truck center of gravity is centered
on the adapter pads to prevent offset loading of posts.
Do not use these to pick up just one end of a vehicle only. Do not use these to pick up vehicles
by tires. Use adapters only in pairs. These adapter are designed only to pick up fork trucks.
The fork truck adapters are intended for use on Mohawk MP-Series 15” Long Fork lifts ONLY.
6
HMMWV ADAPTERS
See next page for HMMWV adapter diagram and specifications.
The HMMWV adapters are specifically to be used when it is desired to raise a HMMWV
(Hummer) by the front and rear bumpers for wheels free servicing. These adapters can also be
used to pick up mobile military generators, a/c units, etc. These adapters are used with a pair of
posts.
Directions for Use:
Drive the vehicle into the lifting area.
Slip the HMMWV adapters over the forks of a master and slave post.
Drop the fork retainer pins in the holes at the carriages.
Locate posts at the front and rear of the vehicle.
Locate lifting pads at desired locations to contact frame at bumper ends.
Ensure pads are at widest settings possible.
Lift pair until pads engaged frame.
Verify proper frame engagement with pads.
Lift pair approximately 6 inches.
Shake truck slightly to ensure secure and balanced support of frame.
Operate lift as desired.
WARNING:
Any removal of components from vehicle while raised may alter the center of gravity of the
vehicle and produce an unsafe or unstable condition of the vehicle or the lifting system that may
cause injury to personnel or damage to equipment. Ensure vehicle center of gravity is always
located at center of lifting pads. Use jack stands as an added measure of safety to ensure load
stabilization.
NOTICE:
The HMMWV adapters are rated for 12,000 lbs per post (24,000 lbs per post pair)
Always ensure that the HMMWV adapters are fully inserted over the lifting forks and retaining
pins are inserted into carriage holes. Also, ensure that HWWMV center of gravity is centered on
the between the pads to prevent offset loading of posts.
Do not use these to pick up just one end of a vehicle only. Use adapters only in pairs.
The HMMWV adapters are intended for use on Mohawk MP-Series 15” Long Fork lifts ONLY.
8
FRAME CONTACT ADAPTERS
See next page for Frame Contact Adapters diagram and specifications.
The frame contact adapters are designed to convert a mobile column lift post pair into a frame
engaging lift for wheels free servicing. These adapters are used with a pair of posts.
Directions for Use:
Drive the vehicle into the lifting area.
Slip the frame contact adapters over the forks of a master and slave post.
Drop the fork retainer pins in the holes at the carriages.
Locate posts at the both sides of the vehicle.
Locate lifting pads at desired locations to contact frame pick up points.
Ensure pads are at widest settings possible for stability.
Lift pair until pads engaged frame.
Verify proper frame engagement with pads.
Lift pair approximately 6 inches.
Shake truck slightly to ensure secure and balanced support of frame.
Operate lift as desired.
WARNING:
Due to the nature of this design where loading of the adapters is outside the base envelope of the
posts, this is a non-certifiable option and voids the certification on the lift it is used on.
WARNING:
Any removal of components from vehicle while raised may alter the center of gravity of the
vehicle and produce an unsafe or unstable condition of the vehicle or the lifting system that may
cause injury to personnel or damage to equipment. Ensure vehicle center of gravity is always
centrally located between the lifting pads. Use jack stands as an added measure of safety to
ensure load stabilization.
NOTICE:
The frame contact adapters are rated for 4,000 lbs per post (8,000 lbs per post pair)
Always ensure that the frame contact adapters are fully inserted over the lifting forks and
retaining pins are inserted into carriage holes. Also, ensure that vehicle center of gravity is
centered between the pads to prevent offset loading of posts.
Do not use these to pick up just one end of a vehicle only. Use adapters only in pairs.
The frame contact adapters are intended for use on Mohawk MP-Series 15” Long Fork lifts
ONLY.
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement