Yamaha | CVP-79A | Specifications | Yamaha CLP-705 Specifications

Yamaha CLP-705 Specifications
IMPORTANT
WICHTIG
IMPORTANT
IMPORTANTE
Check Your Power Supply
Make sure that your local AC mains
voltage matches the voltage specified on the name plate on the bottom
panel. In some areas a voltage selector may be provided on the bottom
panel of the main keyboard unit near
the power cord. Make sure that the
voltage selector is set for the voltage
in your area. The voltage selector is
set at 240V when the unit is initially
shipped. To change the setting use a
“minus” screwdriver to rotate the selector dial so that the correct voltage
appears next to the pointer on the
panel.
Netzspannung überprüfen
Vergewissern Sie sich vor dem Anschließen an das Stromnetz, daß die
örtliche Netzspannung den Betriebsspannungswerten auf dem Typenschild
an der Unterseite des Instruments entspricht. In bestimmten Verkaufsgebieten ist das Instrument mit einem
Spannungswähler an der Unterseite
neben der Netzkabeldurchführung ausgestattet. Falls vorhanden, muß der
Spannungswähler auf die örtliche Netzspannung eingestellt werden. Der
Spannungswähler wurde werkseitig auf
240 V voreingestellt. Zum Verstellen
drehen Sie den Spannungsregler mit
einem Schlitzschraubendreher, bis der
Zeiger auf den korrekten Spannungswert weist
Vérifiez la source d’alimentation
Vérifiez que la tension spécifiée sur
le panneau arrière correspond à la
tension du secteur. Dans certaines
régions, l’instrument peut être équipé
d’un sélecteur de tension situé sur
le panneau inférieur du clavier à
proximité du cordon d’alimentation.
Vérifiez que ce sélecteur est bien
réglé en fonction de la tension secteur de votre région. Le sélecteur de
tension est réglé sur 240 V au départ d’usine. Pour modifier ce réglage, utilisez un tournevis à lame
plate pour tourner le sélecteur afin
de mettre l’indication correspondant
à la tension de votre région vis à vis
du repère triangulaire situé sur le
panneau.
Compruebe la alimentación de su área
Asegúrese de que tensión de alimentación de CA de su área corresponde con la tensión especificada en la
placa de características del panel
inferior de la unidad del teclado principal, cerca del cable de alimentación. Asegúrese de que el selector
de tensión esté ajustado a la tensión
de su área. El selector de tensión
se ajusta a 240V cuando la unidad
sale de fábrica. Para cambiar el ajuste, emplee un destornillador de cabeza “recta” para girar el selector de
modo que aparezca la tensión correcta al lado del indicador del panel.
SPECIAL MESSAGE SECTION
PRODUCT SAFETY MARKINGS: Yamaha electronic
products may have either labels similar to the graphics
shown below or molded/stamped facsimiles of these
graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
See bottom of Keyboard enclosure for graphic symbol markings
The exclamation point with the equilateral triangle is intended to alert the user
to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the
product.
The lightning flash with arrowhead
symbol within the equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electrical shock.
IMPORTANT NOTICE: All Yamaha electronic products
are tested and approved by an independent safety testing
laboratory in order that you may be sure that when it is
properly installed and used in its normal and customary
manner, all foreseeable risks have been eliminated. DO
NOT modify this unit or commission others to do so unless specifically authorized by Yamaha. Product performance and/or safety standards may be diminished. Claims
filed under the expressed warranty may be denied if the
unit is/has been modified. Implied warranties may also be
affected.
SPECIFICATIONS SUBJECT TO CHANGE: The
information contained in this manual is believed to be
correct at the time of printing. However, Yamaha reserves
the right to change or modify any of the specifications
without notice or obligation to update existing units.
ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally
friendly. We sincerely believe that our products and the
production methods used to produce them, meet these
goals. In keeping with both the letter and the spirit of the
law, we want you to be aware of the following:
92-469- ➀
Battery Notice: This product MAY contain a small nonrechargeable battery which (if applicable) is soldered in
place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform
the replacement.
Warning: Do not attempt to recharge, disassemble, or
incinerate this type of battery. Keep all batteries away
from children. Dispose of used batteries promptly and as
regulated by applicable laws. Note: In some areas, the
servicer is required by law to return the defective parts.
However, you do have the option of having the servicer
dispose of these parts for you.
Disposal Notice: Should this product become damaged
beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and
federal regulations that relate to the disposal of products
that contain lead, batteries, plastics, etc.
NOTICE: Service charges incurred due to lack of knowledge relating to how a function or effect works (when the
unit is operating as designed) are not covered by the
manufacturer’s warranty, and are therefore the owners
responsibility. Please study this manual carefully and consult your dealer before requesting service.
NAME PLATE LOCATION: The graphic below indicates the location of the name plate. The model number,
serial number, power requirements, etc., are located on
this plate. You should record the model number, serial
number, and the date of purchase in the spaces provided
below and retain this manual as a permanent record of
your purchase.
CVP-69/69A
CVP-79A
CVP-59S
Model _____________________________________
Serial No. __________________________________
Purchase Date _____________________________
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Introduction
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Thank you for choosing a Yamaha Clavinova. Your Clavinova is a fine musical instrument
that employs advanced Yamaha music technology. With the proper care, your Clavinova will
give you many years of musical pleasure.
● Large LCD (Liquid Crystal Display) panel and a consistent control interface make
operation easy and efficient.
● AWM (Advanced Wave Memory) tone generator system offers an extensive range
of rich, realistic voices.
● A maximum of 32-note polyphony (64-note polyphony on the CVP-79A) permits use
of sophisticated playing techniques.
● Piano-like touch response provides extensive expressive control and outstanding
playability.
● Dual and split play modes allow 2 voices to be played simultaneously or individually
with the left and right hands.
● 100 exciting accompaniment styles can be used to provide rhythm-only accompaniment or fully-orchestrated rhythm, bass, and chord accompaniment. Optional
Style File disks provide additional accompaniment styles.
● Custom Style lets you create original accompaniment patterns that can be recalled
and played in the same way as the presets.
● Full-keyboard ABC (Auto Bass Chord) provides accompaniment as you play across
the entire keyboard.
● 16 Harmony variations make it simple to produce rich, complex harmonies.
● One-touch Setting Feature automatically sets the ideal voices and other parameters for the selected accompaniment style.
● 16-track built-in sequencer records and plays back your keyboard performances.
● Digital reverb and effects add extra ambiance and depth to your sound.
● Registration Memory memorizes 25 (15 in the case of the CVP-59S) complete
control-panel setups that you can recall whenever needed.
● Internal 3.5" floppy disk drive provides extended Song Record capacity and Disk
Orchestra Collection disk playback capability.
Disk Orchestra Collection playback capability lets you practice complete songs with
full accompaniment — while keyboard guide lamps help beginners find the right
keys.
● MIDI compatibility, GM voices, and a range of MIDI functions make the Clavinova
useful in a range of advanced MIDI music systems.
In order to make the most of your Clavinova’s performance potential and features, we urge
you to read this Owner’s Manual thoroughly, and keep it in a safe place for later reference.
The LCD displays as illustrated in this manual are for instructional purposes only, and may appear somewhat different from yours.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Taking Care of Your Clavinova ............... 2
Preparation
3
The Music Stand .................................... 3
The Key Cover (CVP-79A/69/69A) ........ 3
The Power Switch .................................. 3
Headphones ........................................... 3
The Panel Controls
4
The Volume Controls
6
Master Volume ....................................... 6
ABC/Song Volume ................................. 6
Other Volume Controls ........................... 7
Expression Control (CVP-79A only) ....... 7
General Operation: The Display &
Related Controls
8
The Display & LCD Buttons ................... 8
The [DISPLAY HOLD] Button ................ 9
The PAGE [<] and [>] Buttons ........... 10
The [MIXER] Button ............................. 10
Contents
Accompaniment
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
28
Other Song Recording Functions ........ 83
Style Selection ..................................... 28
Track Mix .............................................. 83
Tempo Control ..................................... 29
Track Delete ......................................... 84
Starting the Accompaniment ................ 30
Track Quantize ..................................... 84
Fill-ins ................................................... 32
Initial Edit .............................................. 85
Left-pedal Break ................................... 32
Renaming Song Files ........................... 87
Stopping the Accompaniment .............. 32
Recording Without a Disk ..................... 89
Metronome ........................................... 33
Playback ............................................... 89
Auto Bass Chord (ABC)
34
Keyboard .............................................. 91
Overall Accompaniment Volume
Control .................................................. 37
Pedal .................................................... 92
Individual Part Volume Control ............. 38
MIDI 2 ................................................... 95
Small ABC ............................................ 39
MIDI 3 ................................................... 97
Changing the ABC Split Point .............. 39
Format .................................................. 98
Chord Assist ......................................... 40
Registration .......................................... 99
Harmony ............................................... 41
Transform ........................................... 101
One Touch Setting ............................... 44
Song Copy ......................................... 102
Custom Style
45
Other Custom Style Functions ............. 50
The [CONTRAST] Button ..................... 11
Playing Back Your Custom Styles ........ 52
The Help Function ................................ 11
Custom Style Alert & Error Displays .... 53
Memory Backup ................................... 12
Style File Load
13
Voice Selection
15
Keyboard Percussion ............................ 16
The Keyboard & Polyphony .............. 16
Dual Mode
17
Engaging the Dual Mode &
Selecting the 2nd Voice ....................... 17
Dual-mode Voice Balance .................... 18
Detune Depth ....................................... 18
Digital Reverb
22
Using Loaded Style Files ..................... 57
Registration Memory
58
Recall the Registered Panel
Settings ................................................ 60
Backup ............................................... 107
Recall ................................................. 108
Popup Time ........................................ 109
Messages
110
The Connectors
113
Troubleshooting
114
Options
114
The ABC Freeze Function .................... 60
Disk Orchestra Collection &
Song Playback
61
Index ...................................................... 115
Straight Playback ................................. 61
Overall Song Playback Volume
Control .................................................. 65
Individual Part Volume Control &
Voice Selection .................................... 66
Selecting a Reverb Type ...................... 22
Guided Right- and Left-hand
Practice ................................................ 67
Total Depth Control .............................. 23
Repeat Functions ................................. 69
Individual Part Depth Control ............... 23
Other Playback Controls ...................... 70
Voice Effects
Micro Tuning ...................................... 104
Alert Sound ........................................ 109
Part Assignment for Original Song
Playback ............................................... 65
Changing the Split Point ....................... 21
Song Delete ....................................... 104
Loading Disk Styles .............................. 55
Engaging the Split Mode ...................... 19
Split-mode Voice Balance .................... 20
MIDI 1 ................................................... 94
Song List Priority ................................ 109
Playing Back Specific Parts ................. 63
Changing the Split Voices .................... 19
Sound ................................................... 92
55
19
Split Mode
90
Single-Finger, Fingered Chord, and
Full Keyboard Accompaniment ............ 34
The [EXIT] Button ................................. 10
Demonstration Playback
The Utility Functions
Playing Other Types of Music Data ...... 71
24
Voice List .............................................. 116
Style List ............................................... 120
Drum/key Assignment List .................. 121
Selecting a Voice Effect ....................... 24
Song Recording
72
Backed Up Parameters ........................ 122
Effect Depth Control ............................. 25
Quick Recording .................................... 72
Fingering Chart .................................... 123
One-touch Preset Recall ...................... 25
Multi-track Recording & Playback ........ 75
MIDI Data Format ................................. 124
Adding New Tracks .............................. 77
Specifications ....................................... 135
26
Punch-in/out Recording ........................ 78
CVP-79A: Assembly ............................. 136
Right Pedal (Damper Pedal) ................ 26
The Chord Sequence Function ............. 80
CVP-69/69A: Assembly ........................ 142
Center Pedal (Sostenuto Pedal —
CVP-79A/69/69A only) ......................... 26
Chord Sequence Page 2 & 3
Functions .............................................. 81
CVP-59S: Assembly ............................. 150
The Pedals
MIDI Implementation Chart ................. 156
Left Pedal (Multi-function) .................... 27
1
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Taking Care of Your Clavinova
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Your Clavinova will give you years of playing pleasure if you observe the simple rules given below:
1. Avoid Humidity & Heat
Avoid placing the Clavinova in areas that are subject to excessive
humidity or heat. Do not leave the instrument near heaters or in a
car exposed to direct sunlight, for example.
2. Avoid Dust & Moisture
Avoid locations in which the instrument is likely to be exposed to
excessive dust or moisture.
3. Power-off Before Connecting
Connections between the Clavinova and any other device must
be made with both pieces of equipment turned off.
4. Handle With Care
Never apply excessive force to the controls, connectors or other
parts of your Clavinova, and avoid scratching or bumping it with
hard objects. Further, always turn the POWER switch off after
use, and close the key cover to protect the keyboard (CVP-79A/
69/69A), or cover the instrument with the dust cover provided
(CVP-59S).
• To eject a floppy disk, press the eject button slowly as far as it will
go. Then when the disk Is fully ejected, remove it by hand.
• The disk may not be ejected properly if the eject button is pressed
too quickly or if it is not pressed in far enough. (The eject button
may become stuck halfway with the disk extending from the slot
by only a few millimeters). If this is the case, do not attempt to pull
out the partially ejected disk. Doing so may damage the disk drive
mechanism and/or the floppy disk. To remove a partially ejected
disk, try pressing the eject button once again or push the disk
back into the slot, then repeat the eject procedure carefully.
■ Never open or close the key cover while a disk is extending
from the drive (i.e. in the ejected position). The key cover
may contact the disk, possibly damaging the disk or even
the disk drive.
■ Do not insert anything but floppy disks into the disk drive.
Other objects may cause damage to the disk drive or floppy
disk.
■ Use the 3.5-inch 2DD or 2HD floppy disks with the
Clavinova.
5. Clean Carefully
Clean the cabinet and keys of your Clavinova only with a clean,
slightly damp cloth. A neutral cleanser may be used if desired.
Never use abrasive cleansers, waxes, solvents or chemical dust
cloths since these can dull or damage the finish.
6. Never Tamper With the Internal Circuitry
Never open the Clavinova cabinet and touch or tamper with the
internal circuitry. Tampering with the circuitry can result in electrical shock!
7. Electric Interference
Since the Clavinova contains digital circuitry, it may cause interference if placed too close to radio or television receivers. If this
occurs, move the instrument further away from the affected
equipment.
8. Check Your Power Supply
Make sure that your local AC mains voltage matches the voltage
specified on the name plate on the bottom panel. In some areas
a voltage selector may be provided on the bottom panel of the
main keyboard unit near the power cord. Make sure that the
voltage selector is set for the voltage in your area. The voltage
selector is set at 240V when the unit is initially shipped. To
change the setting use a “minus” screwdriver to rotate the selector dial so that the correct voltage appears next to the pointer on
the panel.
9. Name Plate Location
The Clavinova name plate, including the unit’s serial number, is
located on the bottom panel of the main unit.
10.Handling Floppy Disks
Yamaha Disk Orchestra Collection disks are write-protected and
therefore cannot be used to save songs. To save your recorded
songs a blank floppy disk should be used (one blank disk is supplied with the Clavinova).
Taking Care of Your Floppy Disks
■ Do NOT eject the disk during recording or playback, or at any
time when the disk drive lamp is lit. Doing so may damage both
the disk and the FDD.
■ Do NOT turn the Clavinova on or off while the disk is in the
drive.
■ Always eject the disk before turning the Clavinova off.
■ When ejecting a floppy disk from the disk drive:
Precautions Regarding Floppy Disk Use
■ Never open the disk’s shutter. Dirt or dust on the Internal
magnetic surface will cause data errors.
■ Never leave disks near a speaker, TV, or other device that
emits a strong magnetic field.
■ Do not store disks in places exposed to direct sunlight or
sources of high temperature.
■ Do not place heavy objects such as books on top of a disk.
■ Avoid getting the disks wet.
■ Be sure to store the disks in environmental conditions as
specified below:
• Storage temperature: 4° to 53°C (39° to 127°F).
• Storage humidity: 8 to 90% relative humidity.
• Store in an area free from dust, sand, smoke, etc.
■ Be sure to apply the disk label at the proper position. When
changing the label never cover the old label with a new
label; always remove the old label first.
Head Cleaning
The head of the disk drive unit will get dirty as you use it eventually causing data errors. If this occurs, clean the head with a
3.5 inch head cleaning disk (available from most computer
supply stores).
Data Backup
It is recommended that you copy your recorded songs to
another disk for backup (see page 102). If the original disk is
damaged or your song is deleted, the backup disk can be
used instead of the original.
Protecting Your Data (Write Protect Tab)
Write protect tab
open (locked —
write protected)
Disk drive lamp
2
Write protect tab
closed (unlocked
— write enabled)
Preparation
○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Music Stand
If you will be using sheet music with your Clavinova, raise the music stand built into it’s top panel by lifting the rear edge of the music
stand. Flip down the braces on either side of the rear of the music stand
so that they catch inside the protrusions on the top panel. Reverse this
operation o lower the stand.
The Key Cover (CVP-79A/69/69A)
To open the CVP-79A/69/69A key cover lift it just enough to clear
the keys (do not lift excessively) then slide the cover back into the main
unit. To close the cover slide it forward all the way and then lower it
gently until it closes completely.
CVP-79A
The Power Switch
POWER
After making sure that the Clavinova’s AC cord is properly plugged
into the Clavinova itself and plugged into a convenient AC wall outlet
(a power-plug adaptor may be provided in some areas), press the
[POWER] switch located to the left of the keyboard once to turn the
power on. Press the [POWER] switch again to turn the power off.
When the power is initially turned on, the PIANO voice selector
indicator will light, the POP style selector indicator will light, and the
display will appear as shown to the left.
Headphones
CVP-79A
PHONES
CVP-69/69A/59S
One or two standard pairs of stereo headphones can be plugged in
here for private practice or late-night playing. The internal speaker system is automatically shut off when a pair of headphones is plugged into
either or both of the PHONES jacks.
3
The Panel Controls
CVP-69/69A
R
L/L+R
R
L/L+R
R
L/L+R
R
AUX OUT
AUX IN
IN
EXP PEDAL
L/L+R
AUX OUT
AUX IN
OUT
THRU
OUT
IN
OUT
MIDI
L/L+R
R
R
L/L+R
AUX OUT
AUX IN
F G
MIDI
D
CVP-59S
IN
CVP-79A
○○○○○○○○○○○○○○○○○○○○○○○○
THRU
MIDI
D
H
2 3
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
F
D
6
4
16BEAT
DANCE
POP
ROCK
BALLAD
JAZZ
F
^
7
STYLE
POP
DEMO/HELP
–
HARMONY
H
q
&+
MAX
5
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
COUNTRY
WALTZ
DISK
ONE TOUCH
SETTING
MAIN B
ENDING
SMALL
ABC
PRESET
8
CUSTOM
AUTO BASS CHORD
METRONOME
e
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
MIN
CANCEL
9 0 ! @ # $ %
u
CONTRAST
TEMPO
BEAT
REVERB
MIN
H
* ( )
FUNCTION
MIXER
PAGE
t
w
r
DISPLAY HOLD
y
i
1
POWER
j
A-1 B-1 C0 D0 E0 F0 G0 A0 B0
C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3
AUTO BASS CHORD Section
PHONES
PHONES
S
S
CVP-79A
CVP-69/69A/59S
1 POWER Switch ............................................. page 3
^ [METRONOME] Button ............................... page 33
& TEMPO [▲] and [▼] Buttons ...................... page 29
VOLUME Section
START/STOP Section
2 MASTER VOLUME Control ........................... page 6
3 ABC/SONG VOLUME Control ......... page 6, 37, 65
* [TAP] Button ................................................. page 31
( [SYNCHRO] Button ..................................... page 31
) [START/STOP] Button .................... page 14, 30, 32
4 [DEMO/HELP] Button ........................... page 11, 13
5 [REVERB] Button ........................................ page 22
STYLE Section
6 STYLE Selectors ............................ page 13, 28, 45
7 [HARMONY] Button .................................... page 41
8 [ONE TOUCH SETTING] Button ................. page 44
4
9 [INTRO A/FILL TO A] Button ................ page 30, 32
0 [INTRO B/FILL TO B] Button ................ page 30, 32
! [MAIN A] Button .................................... page 30, 31
@ [MAIN B] Button .................................... page 30, 31
# [ENDING] Button ......................................... page 32
$ [SMALL ABC] Button ................................... page 39
% [ABC ON] Button ......................................... page 35
Display Control Section
q [CONTRAST] Button ................................... page 11
w BEAT Display ............................................... page 31
e [FUNCTION] Button .................................... page 90
r [MIXER] Button ....................................... page 7, 10
t PAGE [<] and [>] Buttons .......................... page 10
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CVP-79A
l
;
l
A
o
RECORD
GUIDE
W E R
p
–
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
Q
FF
CLAVI. TONE/
SYNTH
O a
DUAL
DRUMS/
PERC.
SPLIT
4
5
EFFECT
h
P
REGISTRATION
+
REW
A
VOICE
E. PIANO
CVP-59S
l
A
PIANO
SONG CONTROL
EXIT
;
I
SONG
PLAY
CVP-69/69A
The Panel Controls
PAUSE
T Y U
s d
2
3
f
ABC FREEZE
g
k
F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6 D6 E6 F6 G6 A6 B6 C7
y [DISPLAY HOLD] Button ............................... page 9
u Display ........................................................... page 8
i LCD Buttons .................................................. page 8
o Data dial ........................................................ page 8
p [EXIT] Button ............................................... page 10
Q [+] and [–] Buttons ......................................... page 8
REGISTRATION Section
SONG Section
j Keyboard ...................................................... page 16
k Keyboard Guide Lamps ............................... page 67
W [PLAY] Button .............................................. page 61
E [RECORD] Button ....................................... page 73
R [GUIDE] Button ............................................ page 67
SONG CONTROL Section
T [REW] Button ........................................ page 70, 78
Y [FF] Button ............................................ page 70, 78
U [PAUSE] Button .................................... page 70, 78
VOICE Section
I VOICE Selectors .................................. page 13, 15
O [DUAL] Button .............................................. page 17
P [SPLIT] Button ............................................. page 19
a [EFFECT] Button ......................................... page 24
s [MEMORY] Button ....................................... page 59
d [BANK] Button ............................................. page 59
f [REGISTRATION 1~5] Button .............. page 59, 60
g [ABC FREEZE] Button ................................ page 60
h 3.5" Floppy Disk Drive .............. page 55, 61, 72, 98
l Soft Pedal .................................................... page 27
; Sostenuto Pedal (CVP-79A/69/69A) ........... page 26
A Damper Pedal .............................................. page 26
S PHONES Jacks ............................................. page 3
D AUX OUT R and L/L+R Jacks ................... page 113
F AUX IN R and L/L+R Jacks ....................... page 113
G EXP PEDAL Jack (CVP-79A) .............. page 7, 113
H MIDI Connectors ....................................... page 113
5
The Volume Controls
○○○○○○○○○○○○○○○○○○○○○
The Clavinova has two volume controls on the control panel in
addition to several programmable volume levels that give you extra
versatility in creating the required sound.
VOLUME
MASTER
VOLUME
MAX
ABC/SONG
VOLUME
MAX
STYLE
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
RECORD
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
EXIT
–
REW
MIN
REGISTRATION
+
FF
2
3
ABC FREEZE
PAUSE
MIN
Master Volume
The MASTER VOLUME control adjusts the overall volume of
sound produced by the Clavinova. It also adjusts headphone volume
when one or two pairs of headphones are plugged into the PHONES
jacks.
Initially set the MASTER VOLUME control about half way between
the “MIN” and “MAX” settings. Then, when you start playing, adjust the
control for the most comfortable listening level.
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
ABC/Song Volume
This control adjusts the volume of the Clavinova’s auto-accompaniment and song playback sound. The volume of notes played on the keyboard is not affected.
VOLUME
MASTER
VOLUME
6
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
• The output signal levels from the AUX
OUT jacks are also adjusted by the
MASTER VOLUME control.
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ The
Volume Controls
Other Volume Controls
The [MIXER] button provides access to individual volume parameters for the rhythm, bass, chord, pad, and phrase parts of the auto accompaniment sound, a keyboard volume parameter, and a volume parameter for the Clavinova’s harmony function — see page 41 for details.
When the Clavinova’s Disk Orchestra Collection playback function is in
use the [MIXER] button accesses individual volume parameters for each
Disk Orchestra Collection part.
FUNCTION
MIXER
Expression Control (CVP-79A only)
An optional Yamaha FC7 Foot Controller can be plugged into the
CVP-79A EXP PEDAL jack for foot volume (expression) control of the
keyboard sound only (i.e. expression doesn’t affect the auto-accompaniment sound). Press the pedal forward to increase volume, and backward
to decrease volume.
EXP PEDAL
7
General Operation:
The Display & Related Controls
In addition to a range of direct-operation buttons, the CVP-79A/69/
69A/59S features a large LCD (Liquid Crystal Display) panel and
several related controls that comprise a consistent interface that,
once understood, can make operation and programming easier
than ever.
CONTRAST
BEAT
FUNCTION
MIXER
PAGE
EXIT
DISPLAY HOLD
The Display & LCD Buttons
The 5 buttons below the display — we’ll call them “LCD buttons”
throughout this text — select or edit the parameter indicated by the adjacent section of the display.
In the example display shown here, for example, the two buttons immediately below the VOICE section of the display can be used to select
the voice to be played via the keyboard. When either of the VOICE buttons is pressed the VOICE section of the display will be highlighted (as
in the example), indicating that the data dial and [+]/[–] buttons can also
be used to select voices. The LCD buttons can be pressed briefly to “single-step” the corresponding parameter, or held to scroll continuously
through the parameter’s values. The panel [+]/[–] buttons allow singlestep operation only.
–
8
+
–
+
○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○
General Operation: The Display & Related Controls
In many cases where ▲ and ▼ or < and > LCD buttons appear, both
buttons can be pressed simultaneously to recall the default setting for that
parameter. The panel [+] and [–] buttons can be used in the same way.
This applies to most parameters that have a range of possible settings.
Parameters of this type are enclosed in a rounded frame in the display.
Parameters which are directly executed or simply switched on or off
via the corresponding LCD button appear in a square frame and are not
editable via the data dial and [+]/[–] buttons.
The [DISPLAY HOLD] Button
When selecting voices (page 15) or accompaniment styles (page 28),
for example, the voice or style list that appears when a VOICE or
STYLE button is pressed will automatically disappear after a few seconds if no selections are made. When this type of temporary “pop-up”
display is selected, the [DISPLAY HOLD] button will flash indicating
that the display will disappear in a few seconds. Pop-up displays can be
kept on the LCD for as long as required by pressing the [DISPLAY
HOLD] button so that its indicator lights continuously. Press [DISPLAY
HOLD] a second time (the indicator will go out) to disengage the display hold function.
• If the [DISPLAY HOLD] button is engaged when a normal display is showing, no pop-up displays will appear
even when a button that normally calls
a pop-up display is pressed.
• The length of time pop-up displays
remain on the LCD can be set via the
“Pop-up Time” function described on
page 109.
DISPLAY HOLD
9
General Operation: The Display & Related Controls
○○○○○○○○○○○○○○○○○○○○○○
The PAGE [<] and [>] Buttons
Many functions have several display “pages” that can be selected by
using the PAGE [<] and [>] buttons. When more than one page is provided for the selected function or group of functions, a corresponding
number of overlapping page icons will appear in the upper right-hand
corner of the display, and the number of the currently selected page will
appear in the top page icon.
PAGE
DISPLAY HOLD
The [MIXER] Button
This button calls the CVP-79A/69/69A/59S mixer display which includes individual volume parameters for the auto-accompaniment
RHYTHM, BASS, CHORD, PAD, and PHRASE parts. These parameters can be used to the achieve the best overall balance for your musical
needs (see page 38 for details). The mixer parameters will disappear
when the [MIXER] button is pressed a second time (or the [EXIT] button is pressed).
FUNCTION
MIXER
The [EXIT] Button
The [EXIT] button will usually take you out of the current mode,
back to the previous display — often the initial play mode display.
EXIT
10
○○○○○○○○○○○○○○○○○○○○○○
General Operation: The Display & Related Controls
The [CONTRAST] Button
The CVP-79A/69/69A/59S display panel is a liquid-crystal type
which can be adjusted for optimum legibility. Press the [CONTRAST]
button and use the DARK and LIGHT LCD buttons (or data dial or [+]/
[–] buttons) to set the display contrast for optimum legibility. The contrast setting retained in memory even when the Clavinova power is
turned off.
CONTRAST
Press the [CONTRAST] button again or [EXIT] button to exit from
the LCD CONTRAST display.
The Help Function
If you’re ever in doubt about a function, the CVP-79A/69/69A/59S
HELP function is always available. Press the [DEMO/HELP] button
and then the HELP LCD button at any time to enter the help mode.
DEMO/HELP
If necessary use the first LCD button to select the language (ENGLISH, GERMAN, FRENCH or JAPANESE) you want help in. The language setting is retained in memory even when the Clavinova power is
turned off. Use the SELECT ▲ ▼ buttons to select a topic, then press the
ENTER button to view the first page of help text on the selected topic.
11
General Operation: The Display & Related Controls
○○○○○○○○○○○○○○○○○
Use the PAGE [<] and [>] buttons, the [+] and [–] buttons, or the
data dial to “flip” through the available pages.
PAGE
DISPLAY HOLD
The [EXIT] or [DEMO/HELP] button will take you back to the
topic list if pressed while the help text is showing, or back to the initial
play mode display if pressed while the topic list is showing.
Memory Backup
In addition to the contrast and language settings introduced in this
section, the Clavinova has a range of parameters that can be retained in
memory even while the power is off, so you don’t have to reset all your
favorite settings every time you want to play. The “Backup” function
described on page 107 lets you select which parameters will be backed
up (retained in memory), and which will be reset to their default values
whenever the power is turned off.
Parameters that are backed up will be retained in memory for about a
week if the Clavinova is not turned on during this time. All parameters
will be reset to their default values if the power remains off for longer
than about a week. To ensure that your backed-up settings are maintained, turn the power on for a few minutes at least once a week.
12
Demonstration Playback
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○○
The Clavinova features 25 demonstration tunes that effectively
demonstrate its sound and accompaniment capabilities. Here’s
how you can select and play the demo tunes.
DEMO/HELP
STYLE
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
VOICE
RECORD
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
EXIT
–
REGISTRATION
+
REW
FF
2
3
ABC FREEZE
PAUSE
Z Turn Power On and Set an Initial Volume Level ...............
Press the [POWER] button to turn the power ON, and set the [MASTER VOLUME] control about half way between the “MIN” and
“MAX” settings.
X Press the [DEMO/HELP] button ........................................................
DEMO/HELP
C Select a Play Mode ..........................................................................................
Use the fourth LCD button to select a play mode:
ALL
All 25 demo tunes will repeatedly play back in sequence, starting with the tune you initially select.
RANDOM
All 25 demo tunes will continuously play back in random order,
starting with the tune you initially select.
SINGLE
The selected tune will play through once, then demo playback
will stop.
V Select a Demo Tune ........................................................................................
The demo tunes are selected via the first two LCD buttons, and the
VOICE and STYLE selectors. The VOICE and STYLE indicators flash
in sequence when the [DEMO/HELP] button is pressed.
• Demo tune playback data is not transmitted via the MIDI OUT terminal.
STYLE
POP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
ROCK
COUNTRY
VOICE
BALLAD
WALTZ
JAZZ
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
CLAVI. TONE/
SYNTH
DRUMS/
PERC.
13
Demonstration Playback
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Press an LCD button or selector to start playback of the corresponding tune. You can also start playback from the first LCD tune by pressing
the [START/STOP] button when the ALL or SINGLE play mode is
selected. The corresponding LCD section will be highlighted during
LCD tune playback, and the VOICE or STYLE indicator will flash during voice or style tune playback.
• During voice or style tune playback,
the currently playing voice or style
name will be shown on the display.
B Adjust the Volume ............................................................................................
Use the MASTER VOLUME control to adjust the volume.
N Stop Playback ......................................................................................................
Demo playback can be stopped temporarily by pressing the LCD button, VOICE button, or STYLE button corresponding to the demo tune
which is currently playing, or by pressing the [START/STOP] button.
Press the [DEMO/HELP] or [EXIT] button when you want to stop
demo playback and return to the normal mode.
• The tempo cannot be adjusted during
demo playback.
The Demo Tunes
Song Demo
1
2
Voice Demo
Piano
Harpsi.
Vibes
Guitar
Clavi. Tone/Synth
Organ
Strings/Choir
Brass
Sax/Flute
Style Demo
Pop
Latin
Latin Pop
Traditional
Waltz
Title
Composers
Piano Concerto No.1 op.23 1st movement
A Whole New World from the motion picture “Aladdin”
Peter Ilyich Tchaikovsky
Alan Menken
Polonaise No.6 op.53 “Heroique”
Sonata in C major K.159 (L.104)
Wonderland
Concierto de Aranjuez 2nd movement
No, Only He Who Has Known
Toccata and Fuga in D minor
Symphony No. 5 op.67 1st movement
“La Réjouissance” from Music For The Royal Fireworks
I Left My Heart In San Francisco
Frédéric François Chopin
Domenico Scarlatti
Hiroaki Fujita
Joaquin Rodrigo
Peter Ilyich Tchaikovsky
Johann Sebastian Bach
Ludwig van Beethoven
Georg Friedrich Händel
George Cory
My Way
Sabor A Mi
The Girl From Ipanema
I Could Have Danced All Night
Tennessee Waltz
J. Revaux, C. François & G. Thibaut
Alvaro Carrillo
Antonio Carlos Jobin
Frederic Loewe
Pee Wee King & Redd Stewart
• Some of the demonstration pieces listed above are specially-arranged excerpts from the original compositions listed above.
All other songs are original (©1995 by Yamaha Corporation).
14
Voice Selection
○○○○○○○○○○○○○○○○○○○○○○○○○
The CVP-69/69A/59S has a total of 172 different voices and the CVP79A has 192 that can be selected and played via the keyboard.
There’s also a “Keyboard Percussion” mode that let’s you play a range
of drums and percussion instruments on the keyboard.
VOICE
STYLE
VOLUME
MASTER
VOLUME
MAX
ABC/SONG
VOLUME
DEMO/HELP
POP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
WALTZ
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
RECORD
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
COUNTRY
METRONOME
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
PRESET
FUNCTION
MIXER
CLAVI. TONE/
SYNTH
DUAL
DRUMS/
PERC.
SPLIT
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
EFFECT
4
5
CUSTOM
REVERB
MIN
CLAVI. TONE/
SYNTH
VOICE
GUIDE
BEAT
MAX
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
MIN
START/STOP
SONG CONTROL
PAGE
EXIT
DISPLAY HOLD
–
REGISTRATION
+
REW
FF
2
3
ABC FREEZE
PAUSE
DRUMS/
PERC.
Z Select a Voice ........................................................................................................
The CVP-79A/69/69A/59S voices are organized in 12 voice groups
(see page 116 for a complete voice list). Use the voice group buttons to
select the group from which you want to select a voice. The corresponding voice display will appear.
VOICE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
CLAVI. TONE/
SYNTH
DRUMS/
PERC.
DUAL
EFFECT
SPLIT
• The display will automatically revert to
the main play mode display after a few
seconds if the [DISPLAY HOLD] button
is not engaged (page 9).
• The last voice selected within each
group will automatically be recalled
whenever a VOICE button is pressed
(as long as the power remains on).
The last-selected voice in each group
can be backed up, even after the
power is turned off, via the “Backup”
function — page 107.
• The Grand Piano 1 voice is automatically selected when the power is initially turned on.
However the last-selected voice can
be recalled when the power is turned
off and on via the “Backup” function —
page 107.
Use the PAGE buttons to select the page containing the voice you
want if more than one page is available, then press the LCD button corresponding to the desired voice. You can also use the data dial or [+]/[–]
buttons to select any of the voices within the selected group.
PAGE
DISPLAY HOLD
Voices within the current group can still be selected via the VOICE ▲
and ▼ LCD buttons, or the data dial or [+]/[–] buttons, once the VOICE
section of the display has been highlighted, from the main play mode
display.
15
Voice Selection
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
X Play & Adjust Volume ...................................................................................
You can now play the selected voice on the CVP-79A/69/69A/59S
keyboard. Use the [MASTER VOLUME] control to adjust the overall
volume level.
Keyboard Percussion
The Clavinova has 8 Drum Kits in the [DRUMS/PERC.] voice group
which includes a range of drum and percussion voices as well as sound
effects. When one of the Drum Kit voices is selected, you can play 72
different drums and percussion instruments on the keyboard. The drums
and percussion instruments played by the various keys when the Standard Kit is selected are marked by symbols above the keys.
See page 121 for a complete list of the instruments in each Drum Kit.
• When a Drum Kit voice is selected only
the keys with drum or percussion
symbols printed above them will
sound.
• The TRANSPOSE, TUNE, and OCTAVE SHIFT functions described on
pages 91 and 92 do not affect the
Drum Kit voices.
VOICE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
CLAVI. TONE/
SYNTH
DRUMS/
PERC.
DUAL
EFFECT
SPLIT
The Keyboard & Polyphony
The CVP-69/69A/59S can play up to 32 notes at once while the CVP-79A can play up to 64. This number
includes all notes being played at the same time in any single or combination use of dual, split, accompaniment, and disk functions. Further variation occurs with “1-element” and “2-element” voices: the polyphony is
halved with 2-element voices. The same applies to stereo voices. The voice list on page 116 shows all stereo,
2-element, and 1-element voices in the CVP-79A/69/69A/59S.
The Clavinova also offers keyboard touch response, so the volume and timbre of notes played can be controlled according to how “hard” you play the keys. The amount of variation available depends on the selected
voice and the setting of the TOUCH SENSITIVITY parameter (page 91).
16
Dual Mode
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The DUAL mode makes it possible to play two voices simultaneously across the entire range of the keyboard. This makes it easy
to create exceptionally rich, thick tonal textures.
STYLE
VOLUME
MASTER
VOLUME
MAX
ABC/SONG
VOLUME
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
RECORD
DUAL
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
MAX
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
REVERB
MIN
AUTO BASS CHORD
MAIN A
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
SONG CONTROL
START/STOP
PAGE
MIN
EXIT
DISPLAY HOLD
–
REGISTRATION
+
MEMORY
REW
FF
BANK
1
2
3
ABC FREEZE
PAUSE
Engaging the Dual Mode & Selecting the 2nd Voice
After selecting the main voice in the normal way, press the [DUAL]
button so that its indicator lights to engage the DUAL mode (by pressing
again, its indicator goes out and the DUAL mode is disengaged).
VOICE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
CLAVI. TONE/
SYNTH
DRUMS/
PERC.
DUAL
EFFECT
SPLIT
• Please note that only the VOICE
group button indicator of the 2nd voice
group lights while the DUAL mode
pop-up display is showing, and that
only the main voice group indicator
lights after the DUAL mode pop-up
display disappears.
• The default DUAL mode 2nd voice is
Strings Slow.
Use the 2nd VOICE LCD buttons in the DUAL mode pop-up display, that appears when the [DUAL] button is turned on, to select the
2nd dual-mode voice (all voice groups are available). The data dial and
[+]/[–] buttons can also be used once the 2nd VOICE section of the
display has been highlighted.
The VOICE selector indicator of the group containing the 2nd voice
lights while the DUAL mode pop-up display is showing, and the 2nd
voice group can be selected via the VOICE selectors. The names of both
the main and 2nd dual-mode voices appear separated by a “+” symbol in
the normal play mode display even after the DUAL mode pop-up display
disappears. A different main voice can be selected in the normal way
once the normal play mode display reappears.
17
Dual Mode
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The DUAL mode pop-up display can be recalled at any time in order
to change the 2nd voice or other settings (see below) by pressing a
VOICE selector (either the current voice or another voice to select the
2nd voice) while holding the [DUAL] button.
Dual-mode Voice Balance
The volume balance between the two voices combined in the DUAL
mode can be adjusted by pressing the BAL (balance) LCD button to
highlight the BAL section of the display, and then by using the data dial
and [+]/[–] buttons. The BAL LCD button can be held to increase the
level of the 2nd voice only. The balance bar in the BAL section of the
display graphically shows the volume balance between the main (1st)
and 2nd voices. Equal balance can be instantly recalled by pressing the
[+] and [–] buttons simultaneously while the BAL parameter is selected.
–
+
Detune Depth
In many cases an even “thicker” sound can be produced by slightly
detuning the dual-mode main and 2nd voices. The DETUNE DEPTH
LCD buttons can be used to set the detune depth value between 0 and 10.
The data dial and [+]/[–] can also be used once the DETUNE DEPTH
parameter is selected. The higher the value the greater the amount of
detuning. The “normal” setting of “5” can be instantly recalled by pressing both the DETUNE DEPTH LCD buttons simultaneously.
• The dual and split modes cannot be
used at the same time.
• The OCTAVE SHIFT function — page
91 — can be used to shift the pitch of
the main and/or 2nd voice in the DUAL
mode up or down one octave.
• The DUAL mode balance and depth
settings affect all voice combinations.
• The DUAL mode settings are retained
even if the DUAL mode is turned off
and on while the power remains on.
The DUAL mode settings can also be
backed up even after the power is
turned off via the “Backup” function —
page 107.
The DUAL mode can be turned off by pressing the [DUAL] button so
that its indicator goes out.
18
Split Mode
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The split mode lets you play different voices with the left and right
hands — bass with the left and piano with the right, for example.
You can assign any of the Clavinova’s voices to the left and righthand sections of the keyboard.
STYLE
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
RECORD
PLAY
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
SPLIT
EFFECT
BEAT
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
EXIT
DISPLAY HOLD
–
REGISTRATION
+
REW
FF
2
3
ABC FREEZE
PAUSE
Engaging the Split Mode
When the [SPLIT] button is pressed and its indicator lights, the keyboard is split into left- and right-hand sections and different voices can
be assigned to each. (The Split mode can be turned off by pressing the
[SPLIT] button again so that its indicator goes out.) The split point is
initially set at the F#2 key when the power is turned on, and the Acoustic
Bass 1 voice is initially assigned to the left-hand section of the keyboard
(all keys up to and including F#2). The voice that was selected when the
SPLIT mode was engaged is assigned to the right-hand section of the
keyboard.
VOICE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
CLAVI. TONE/
SYNTH
DRUMS/
PERC.
DUAL
EFFECT
SPLIT
F 2
Left-hand section
C0
C1
C2
C3
C4
C5
C6
C7
Right-hand section
Changing the Split Voices
Use the LEFT VOICE LCD buttons in the SPLIT mode pop-up display, that appears when the [SPLIT] button is turned on, to select the
left-hand voice (all voice groups are available). The data dial and [+]/[–]
buttons can also be used once the LEFT VOICE section of the display
has been highlighted.
19
Split Mode
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The VOICE selector indicator of the group containing the left-hand
voice lights while the SPLIT mode pop-up display is showing, and the
left-hand voice group can be selected via the VOICE selectors. The
names of both the left- and right-hand voices appear separated by a “/”
symbol in the normal play mode display even after the SPLIT mode popup display disappears. A different right-hand voice can be selected in the
normal way once the normal play mode display reappears.
The SPLIT mode pop-up display can be recalled at any time in order
to change the left-hand voice or other settings (see below) by pressing a
VOICE selector (either the current voice or another voice to select the
left-hand voice) while holding the [SPLIT] button.
Split-mode Voice Balance
The volume balance between the left- and right-hand voices can be
adjusted by pressing the BAL (balance) LCD button to highlight the BAL
section of the display, and then by using the data dial and [+]/[–] buttons.
The BAL LCD button can be held to increase the level of the right-hand
voice only. The balance bar in the BAL section of the display graphically
shows the volume balance between the left- and right-hand voices. Equal
balance can be instantly recalled by pressing the [+] and [–] buttons simultaneously while the BAL parameter is selected.
–
20
+
• Please note that only the VOICE
group button indicator of the left-hand
voice group lights while the SPLIT
mode pop-up display is showing, and
that only the right-hand voice group
indicator lights after the SPLIT mode
pop-up display disappears.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Split Mode
Changing the Split Point
The split point can be set at any key by pressing the desired key while
holding the [SPLIT] button. The split point key name will appear in the
SPLIT POINT section of the display.
UITAR
BASS
CLAVI. TONE/
SYNTH
DRUMS/
PERC.
DUAL
EFFECT
SPLIT
• The dual and split modes cannot be
used at the same time.
• Whether the damper pedal affects the
left voice only, the right voice only, or
both voices is determined by the
“DAMPER RANGE” function described
on page 93 (the default is right-hand
voice only).
• The OCTAVE SHIFT function — page
91 — can be used to shift the pitch of
the left- and/or right-hand voice in the
SPLIT mode up or down one octave.
The split point can also be set by using the SPLIT POINT LCD buttons, or the data dial or [+]/[–] buttons once the SPLIT POINT section
of the display has been highlighted. The keyboard guide lamp corresponding to the selected split point will light.
• When the ABC Single Finger or Fingered mode (page 35) and the split
mode are used simultaneously, the
left-hand voice will be accompanied by
the appropriate ABC chord voices.
• The SPLIT mode balance and split
point settings affect all voice combinations.
• The SPLIT mode settings are retained
even if the SPLIT mode is turned off
and on while the power remains on.
The SPLIT mode settings can also be
backed up even after the power is
turned off via the “Backup” function —
page 107.
The default split point — F#2 — can be recalled by simultaneously
pressing the SPLIT POINT LCD buttons or [+] and [–] buttons.
The SPLIT mode can be turned off by pressing the [SPLIT] button so
that its indicator goes out.
21
Digital Reverb
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The CVP-79A/69/69A/59S provides a number of digital reverb
types that you can use for extra “ambiance” and expressive power.
STYLE
VOLUME
REVERB
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
RECORD
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
EXIT
–
REGISTRATION
+
REW
FF
2
3
ABC FREEZE
PAUSE
Selecting a Reverb Type
Press the [REVERB] button so that its indicator lights to turn the
currently selected reverb effect on (since the REVERB indicator is automatically on when the power is initially turned on, you may have to turn
it off and then on again). —The reverb effect is alternately turned on and
off every time the [REVERB] button is pressed.
REVERB
• Reverb is turned on and the HALL 1
effect is automatically selected when
the POWER switch is turned on.
However, the last setting can be recalled when the power is turned off
and on via the “Backup” function —
page 107.
Different reverb types and depth settings can be selected via the popup display that appears when the [REVERB] button is turned on. Use
the TYPE LCD buttons to select the desired reverb type, or use the data
dial or [+]/[–] buttons when the TYPE parameter is highlighted.
Reverb Type List
HALL1
HALL2
ROOM1
ROOM2
ROOM3
STAGE1
STAGE2
PLATE
WHITE ROOM
TUNNEL
CANYON
22
Concert hall reverb.
• “OFF” may appear if the reverb type
“off” message is received via MIDI.
Small room reverb.
Reverb for solo instruments.
Simulated steel plate reverb.
Distinctive short reverb with initial delay.
Simulation of long tunnel-like space.
(CVP-79A only)
Long, cavernous reverb.
BASEMENT
Small, highly reflective room reverb.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Digital Reverb
Total Depth Control
The overall depth of the selected reverb type can be increased or decreased by using the TOTAL DEPTH LCD buttons, or the data dial or [+]/
[–] buttons when the TOTAL DEPTH parameter is highlighted. The total
depth range is from “0” (no reverb) through “100” (maximum reverb).
The default TOTAL DEPTH value of “50” can be instantly recalled by
pressing both the TOTAL DEPTH LCD buttons or [+] and [–] buttons
simultaneously.
Individual Part Depth Control
The depth of the reverb effect applied to the accompaniment rhythm,
bass, chord, and keyboard parts can be individually adjusted via the parameters provided in page 2 of the reverb display. These values are relative to the total depth value. Use the PAGE buttons to select page 2,
press the LCD button corresponding to the part for which you want to
adjust the reverb depth, then use the data dial or [+]/[–] buttons to adjust
the reverb depth as required. The LCD buttons can be held to increase
the depth for the corresponding part only. The individual part reverb
depth range is from “0” (no reverb) to “100” (maximum reverb). The
default setting of “50” can be instantly recalled for any part by simultaneously pressing the [+] and [–] buttons while the depth parameter for
the desired part is selected.
–
• The TOTAL DEPTH setting applies to
all parts.
• The actual reverb depth for each part
is determined by the product of the
TOTAL DEPTH and individual part
depth settings. For example, if one is
“0”, no reverb will be produced even if
the other is “100”.
• Both total and individual part depth can
be adjusted in five steps.
+
23
Voice Effects
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Each CVP-79A/69/69A/59S voice has individual effect type and depth
settings that can be programmed as required. A range of 20 (17 in the
case of the CVP-69/69A/59S) effects provides extensive musical
versatility.
STYLE
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
RECORD
EFFECT
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
COUNTRY
WALTZ
PRESET
METRONOME
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
EXIT
–
REGISTRATION
+
REW
FF
2
3
ABC FREEZE
PAUSE
Selecting a Voice Effect
Press the [EFFECT] button so that its indicator lights to turn the currently selected voice effect on (press again so that its indicator goes out
to turn the effect off).
VOICE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
CLAVI. TONE/
SYNTH
DRUMS/
PERC.
DUAL
EFFECT
SPLIT
Different effect types and depth settings can be selected via the popup display that appears when the [EFFECT] button is turned on. Use the
TYPE LCD buttons to select the desired effect type, or use the data dial
or [+]/[–] buttons when the TYPE parameter is highlighted.
The default effect type can be recalled by simultaneously pressing the
TYPE LCD buttons or [+]/[–] buttons.
• “OTHERS” or “OFF” may appear if
another effect type or off is set to a
voice or received via MIDI.
Effect Type List
CHORUS1
CHORUS2
CHORUS3
CELESTE
DETUNE
Conventional chorus program with
rich, warm chorusing.
Three-phase LFO for richer, more
pronounced chorusing.
Slight pitch change for each channel.
DELAY L,C,R
DELAY L,R
ECHO
CROSS DELAY
(CVP-79A only)
FLANGER
SYMPHONIC
AUTO PAN
24
Pronounced three-phase modulation
with slight metallic sound.
Exceptionally rich & deep chorusing.
Several panning effects that automatically shift the sound position (left,
right).
TREMOLO
ROTARY FAST
ROTARY SLOW
Three independent delays, for the
left, right and center stereo positions.
Initial delay for each stereo channel,
and two separate feedback delays.
Stereo delay.
Complex effect that sends the delayed repeats “bouncing” between
the left and right channels.
Rich Tremolo effect with both volume
and pitch modulation.
Rotary speaker simulation.
Rotary speaker simulation.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
PHASER
AUTO WAH
TOUCH WAH
(CVP-79A only)
Pronounced, metallic modulation with
periodic phase change.
Repeating filter sweep “wah” effect.
Wah effect that varies filter sweep
according to touch.
COMPRESSOR
(CVP-79A only)
BOOST HL
Voice Effects
Affects the dynamics of the sound by
smoothing out the high-volume
peaks and soft-volume dips.
Equalizer to boost high and low
frequencies.
Effect Depth Control
When a single voice is selected only one depth parameter will appear.
When the DUAL or SPLIT mode is engaged, separate depth parameters
will appear for the main and 2nd (dual) or right- and left-hand (split)
voices. The depth of the selected effect can be increased or decreased by
using the DEPTH1(R) and/or DEPTH2(L) LCD buttons, or the data dial
or [+]/[–] buttons when the DEPTH1(R) or DEPTH2(L) parameter is
highlighted. The DEPTH1(R) and DEPTH2(L) buttons can be held to
only increase the depth of the corresponding voice. The depth range is
from “0” (no effect) to “100” (maximum effect depth). The default
DEPTH1(R) or DEPTH2(L) setting can be instantly recalled for either
depth parameter by simultaneously pressing the [+] and [–] buttons while
the desired depth parameter is selected — DEPTH2(L) is reset to “50”.
–
• The main or right-hand voice effect
type is commonly used for the 2nd or
left-hand voice.
• The depth can be adjusted in five step
intervals.
• The DEPTH1(R) and/or DEPTH2(L)
value for some effect types may be
fixed to 100 and/or 0 respectively and
cannot be changed.
+
One-touch Preset Recall
Press the PRESET LCD button to instantly recall the preset effect
type and DEPTH1(R) settings for the current voice. The DEPTH2(L)
setting is not affected.
• Each voice has its own individual
default effect on/off, type, and depth
settings. Your own settings can be
backed up via the Backup function
described on page 107.
• The DEPTH2(L) setting affects all
voices. Its default value is “50”, but
your own setting can be backed up via
the Backup function described on page
107.
25
The Pedals
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The CVP-79A/69/69A has three pedals and the CVP-59S has two
pedals which offer a range of advanced expressive capabilities.
Right Pedal (Damper Pedal)
The damper pedal functions in the same way as a damper pedal on an
acoustic piano. When the damper pedal is pressed notes played have a
long sustain. Releasing the pedal immediately stops (damps) any sustained notes.
CVP-79A
CVP-69/69A
Damper Pedal
• The CVP-79A damper pedal can be
set for continuous (default) or on/off
type damping control via the
“DAMPER MODE” function (page 94).
CVP-59S
Damper Pedal
Damper Pedal
Center Pedal (Sostenuto Pedal — CVP-79A/69/69A only)
If you play a note or chord on the keyboard and press the sostenuto
pedal while the note(s) are held, those notes will be sustained as long as
the pedal is held (as if the damper pedal had been pressed) but all subsequently played notes will not be sustained. This makes it possible to sustain a chord, for example, while other notes are played “staccato.”
CVP-79A
Sostenuto Pedal
26
CVP-69/69A
Sostenuto Pedal
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Pedals
Left Pedal (Multi-function)
The left pedal has a number of functions which can be selected via
the LEFT PEDAL function described on page 93.
CVP-79A
CVP-69/69A
Left Pedal
Left Pedal
CVP-59S
• The damper and sostenuto pedal
functions do not affect DRUMS/PERC.
voices where inappropriate.
Left Pedal
CVP-79A
Soft
Pressing the soft pedal subtly reduces the volume and
slightly changes the timbre of notes played. The SOFT
function is automatically selected when the POWER
switch is initially turned on.
Start/Stop
The left pedal performs the same function as the accompaniment section [START/STOP] button. For details on
the START/STOP function, refer to the “Accompaniment”
section, pages 30 and 32.
Harmony On/Off
Allows the Harmony function (page 41) to be turned on or
off as required while playing so that harmony can be
applied only to specific notes or phrases.
Registration +
Steps through the registration memory locations so a
completely different set of panel settings can be recalled
each time the pedal is pressed. See page 60 for details
on the registration memory.
Intro A/Fill to A
The left pedal performs the same function as the accompaniment section [INTRO A/FILL TO A] button. See
pages 30 and 32 for details.
Intro B/Fill to B
The left pedal performs the same function as the accompaniment section [INTRO B/FILL TO B] button. See
pages 30 and 32 for details.
Ending/rit.
The left pedal performs the same function as the accompaniment section [ENDING] button. See page 32 for
details.
Break
Pressing the left pedal produces a break in the accompaniment for as long as the pedal is held. For details on the
BREAK function, refer to the “Accompaniment” section,
page 32.
Sostenuto
The left pedal functions in the same way as the CVP79A/69/69A sostenuto pedal (see above).
(CVP-59S only)
27
Accompaniment
○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The CVP-79A/69/69A/59S has 100 musical “styles” that can be used
as a basis for rhythm accompaniment, or fully orchestrated rhythm,
bass, and chord accompaniment (see “Auto Bass Chord” on page 34).
• Accompaniment playback data is not usually transmitted via the MIDI OUT connector. But it
can be transmit-enabled via the MIDI 3 “Send” function described on page 97.
STYLE
POP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
ROCK
BALLAD
JAZZ
WALTZ
DISK
–
METRONOME
COUNTRY
TEMPO
+
PRESET
STYLE
VOLUME
MASTER
VOLUME
CUSTOM
INTRO A/
FILL TO A
INTRO B/
FILL TO B
AUTO BASS CHORD
MAIN A
MAIN B
ENDING
SMALL
ABC
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
REVERB
WALTZ
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
METRONOME
TAP
SYNCHRO
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
PRESET
FUNCTION
MIXER
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
EXIT
–
CLAVI. TONE/
SYNTH
DUAL
DRUMS/
PERC.
SPLIT
4
5
EFFECT
REGISTRATION
+
REW
ABC ON
RECORD
BEAT
COUNTRY
CUSTOM
START/STOP
FF
2
3
ABC FREEZE
PAUSE
START/STOP
Style Selection
The CVP-79A/69/69A/59S’s 100 preset accompaniment styles are
organized in 11 groups (see page 120 for a complete style list). Use the
STYLE selectors to select the group from which you want to select a
style. The corresponding style display will appear.
STYLE
POP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
ROCK
COUNTRY
BALLAD
JAZZ
HARMONY
WALTZ
DISK
ONE TOUCH
SETTING
CUSTOM
• The display will automatically revert to
the main play mode display after a few
seconds if the [DISPLAY HOLD] button
is not engaged (page 9).
• The last style selected within each
group will automatically be recalled
whenever a STYLE button is pressed
while the power remains on. The last
selected style in each group can also
be backed up even after the power is
turned off via the “Backup” function on
page 107.
• The Pop Ballad 1 style is automatically
selected when the power is turned on.
However, the last-selected style can
be recalled when the power is turned
off and on via the “Backup” function on
page 107.
Use the PAGE buttons to select the page containing the style you
want if more than one page is available, then press the LCD button corresponding to the desired style. You can also use the data dial or [+]/[–]
buttons to select any of the styles within the selected group.
28
• There is also a [DISK/CUSTOM] button that can be used to select styles
loaded from optional Style File floppy
disks or disks containing custom styles
you have created yourself. See the
“Style File Load” and “Custom Style”
sections on pages 55 and 45 for details.
• Use the [ABC/SONG VOLUME] control
to adjust the volume of the accompaniment sound.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
PAGE
Accompaniment
DISPLAY HOLD
Styles within the current group can still be selected via the STYLE ▲
and ▼ LCD buttons, or the data dial or [+]/[–] buttons once the STYLE
section of the display has been highlighted, from the main play mode
display.
Tempo Control
Whenever you select a different style, the preset tempo for that style
is also selected, and the tempo is displayed on the display in number of
beats per minute (unless the accompaniment is playing, in which case the
same tempo is maintained).
• The preset tempo for the selected style
can be recalled at any time by pressing
both the TEMPO [+] and [–] buttons
simultaneously.
Tempo
You can change the tempo to any value between 32 and 280 beats per
minute, however, by using the TEMPO [+] and [–] buttons. This can be
done either before the accompaniment is started or while it is playing.
Press either button briefly to decrement or increment the tempo value by
one, or hold the button for continuous decrementing or incrementing.
–
TEMPO
+
PRESET
29
Accompaniment
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Starting the Accompaniment
There are several ways to start the accompaniment:
■ Straight Start .........................................................................................................
Press the [START/STOP] button.
Each of the styles also has two main variations that can be selected by
pressing the [MAIN A] button or [MAIN B] button before pressing the
[START/STOP] button. Normally the [MAIN A] button LED will be lit
(or you can select it if the other variation is selected), indicating that the
MAIN A pattern is selected. You can also switch between the [MAIN A]
and [MAIN B] variations during playback — the new variation begins
from the top of the next measure if the button is pressed on or after the
2nd beat of a measure.
The [START/STOP] button indicator will be lit during accompaniment playback and off when the accompaniment is stopped.
INTRO A/
FILL TO A
INTRO B/
FILL TO B
AUTO BASS CHORD
MAIN A
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
■ Start With an Introduction .......................................................................
Press the [INTRO A/FILL TO A] or [INTRO B/FILL TO B] button.
In the first case the [INTRO A/FILL TO A] indicator will light continuously and the [MAIN A] indicator will flash, indicating that the
MAIN A variation will play after an appropriate introduction. In the latter case the [INTRO B/FILL TO B] indicator will light continuously
and the [MAIN B] indicator will flash, indicating that the MAIN B variation will play after an appropriate introduction. Press the [START/
STOP] button to actually start playback. The selected introduction can
be disengaged before starting playback by pressing the [MAIN A],
[MAIN B], or [ENDING] button.
30
AUTO BASS CHORD
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
MAIN B
ENDING
AUTO BASS CHORD
MAIN B
ENDING
START/STOP
SMALL
ABC
ABC ON
TAP
SMALL
ABC
ABC ON
TAP
SYNCHRO
START/STOP
START/STOP
SYNCHRO
START/STOP
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Accompaniment
■ Synchronized Start .........................................................................................
Any of the start types described above can be synchronized to the first
note or chord played on the keyboard by first pressing the [SYNCHRO]
button so that its indicator lights. When the keyboard is split or Auto
Bass Chord Single Finger or Fingered mode is used, the first note played
on the left-hand section of the keyboard will start the accompaniment
(i.e. keys to the left of and including the split-point key — normally
F#2). Use the [MAIN A], [MAIN B] and/or [INTRO A/FILL TO A] or
[INTRO B/FILL TO B] buttons to select the type of start you want.
START/STOP
TAP
SYNCHRO
START/STOP
The first (red) dot of the BEAT display will flash at the current tempo
when a synchronized start mode has been selected. The synchronized
start mode can be canceled by pressing the [SYNCHRO] button a second time so that its indicator goes out. The synchronized start mode is
automatically canceled once playback has started.
• If the [SYNCHRO] button is pressed
during playback, playback is stopped
and the synchronized start mode is
automatically engaged.
■ Tap start ......................................................................................................................
This function lets you set the tempo and start the rhythm in one operation. Simply tap the [TAP] button at the required tempo — 3 times for
a 3/4 style, 4 times for 2/4, 4/4, and 6-beat styles, and 5 times for 5-beat
styles. The rhythm will start from the beginning of the next measure at
the specified tempo.
• The [TAP] button can also be used to
change the tempo during rhythm playback (tap twice). In this case the “tap”
click will not sound.
• If you tap the [TAP] button less than
the required number of times (i.e. 3, 4,
or 5), the tap tempo function will be
canceled after a few seconds.
START/STOP
TAP
SYNCHRO
START/STOP
■ The Beat Display ...............................................................................................
The four LED dots of the BEAT display provide a visual indication of
the selected tempo during accompaniment playback. The leftmost (red)
dot flashes on the first beat of each measure, the second dot flashes on
the second beat, and so on (all dots except the leftmost dot are green).
The current measure number appears on the LCD during playback.
Measure number
BEAT
31
Accompaniment
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Fill-ins
The CVP-79A/69/69A/59S provides four types of automatic “fill-ins.”
● Fill To A:
Press the [INTRO A/FILL TO A] button during playback to produce a fill-in and go to the MAIN A rhythm
pattern. Different fill-in patterns are produced when going from A to A or B to A.
● Fill To B:
Press the [INTRO B/FILL TO B] button during playback to produce a fill-in and go to the MAIN B pattern.
Different fill-in patterns are produced when going from A
to B or B to B.
INTRO A/
FILL TO A
INTRO B/
FILL TO B
AUTO BASS CHORD
MAIN A
MAIN B
ENDING
SMALL
ABC
ABC ON
If you hold one of the FILL buttons, the fill-in will repeat until the
end of the measure in which button is released. If you press a fill-in button during the fill-in, the fill-in will stop and playback of the previous
variation will resume.
Left-pedal Break
When the left-pedal function is set to “Break” as described on pages
27 and 93, the left pedal can be used to create a break in the accompaniment while playing. Press the left pedal to mute the accompaniment
sound. Accompaniment sound will resume from the top of the next
measure when the pedal is released. The break can be canceled before
the beginning of the next measure by pressing the pedal a second time.
CVP-79A
Stopping the Accompaniment
The accompaniment can be stopped at any time by pressing the
[START/STOP] button. Press the [ENDING] button if you want to go
to the ending pattern and then stop. Press [ENDING] a second time during ending playback to produce a ritardando (gradually slowing) ending.
Different ending patterns are provided for the MAIN A and MAIN B
32
• Playback will start with the ending
pattern if you press the [ENDING]
button before starting playback. The
ending can be disengaged before
starting playback by pressing any other
variation button.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
variations (the [MAIN A] or [MAIN B] button indictor will flash during
the ending). The ending will begin from the top of the next measure if
the [ENDING] button is pressed on or after the 2nd beat of a measure.
START/STOP
TAP
INTRO A/
FILL TO A
INTRO B/
FILL TO B
SYNCHRO
START/STOP
AUTO BASS CHORD
MAIN A
MAIN B
ENDING
SMALL
ABC
ABC ON
Accompaniment
• During playback the indicator of the
currently-playing variation will be lit
while that of the next variation to play
flashes. (The only exception is: during
playback of the ending, the flashing
[MAIN A] or [MAIN B] button indicator
indicates which ending variation is
currently playing.)
• If the left pedal is switched to START/
STOP operation (pages 27 and 93), it
performs the same function as the
panel [START/STOP] buttons (press to
START, press again to STOP). The left
pedal can also be assigned for INTRO
A/FILL TO A, INTRO B/FILL TO B, and
ENDING operation — pages 30 and
32.
Metronome
The CVP-79A/69/69A/59S also offers a metronome function that is
ideal for practice.
To start the metronome, simply press the [METRONOME] button so
that its indicator lights. The metronome will play at the currently selected
tempo whether a style is playing or not. The metronome volume can be
adjusted via the [ABC/SONG VOLUME] control.
• If a style is started by pressing the
[START/STOP] button while the metronome is playing, the metronome will
continue to sound along with the style.
• The metronome bell accent will not
sound during accompaniment playback.
METRONOME
The pop-up screen that appears when the [METRONOME] button is
pressed also provides access to a range of other metronome settings.
When “NORMAL” is selected the metronome click sounds continuously
at the current tempo with no accented beats. The “4/4”, “3/4”, “2/4”, and
“5/4” settings produce a bell accent on the first beat of each measure.
Press the [METRONOME] button again to stop the metronome
sound (the METRONOME indicator will go out). The metronome will
also stop automatically if the [START/STOP] button is pressed to stop a
style in progress.
33
Auto Bass Chord (ABC)
○○○○○○○○○○○○○○○○○○○
The CVP-79A/69/69A/59S includes a sophisticated auto-accompaniment system (Auto Bass Chord — ABC) that can provide automated rhythm, bass and chord backing in a number of ways.
STYLE
POP
16BEAT
LATIN
POP
LATIN
DANCE
POP
TRADITIONAL
ROCK
COUNTRY
BALLAD
WALTZ
JAZZ
DISK
–
HARMONY
ONE TOUCH
SETTING
METRONOME
TEMPO
+
PRESET
STYLE
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
RECORD
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
CUSTOM
INTRO A/
FILL TO A
INTRO B/
FILL TO B
AUTO BASS CHORD
MAIN A
MAIN B
ENDING
SMALL
ABC
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
EXIT
–
REW
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
Single-Finger, Fingered Chord, and
Full Keyboard Accompaniment
“Single Finger” accompaniment makes it simple to produce accompaniment using major,
seventh, minor and minor-seventh chords by pressing a minimum number of keys in the ABC
section of the keyboard. The automatic accompaniment consists of rhythm, bass and chords.
“Fingered Chord” accompaniment is ideal if you already know how to play chords on a
keyboard, since it allows you to supply your own chords for the auto accompaniment feature.
When the “Full Keyboard” mode is selected the Clavinova will automatically create appropriate accompaniment while you play just about anything, anywhere on the keyboard.
Z Select a Style .........................................................................................................
Select an accompaniment style using the style selectors and STYLE
pop-up screen (see “Style Selection” on page 28).
X Set the Tempo .......................................................................................................
Use the TEMPO [+] and [–] buttons to set the desired accompaniment tempo if necessary (see “Tempo Control” on page 29 for more details).
–
TEMPO
PRESET
34
+
REGISTRATION
+
FF
PAUSE
2
3
ABC FREEZE
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Auto Bass Chord (ABC)
C Turn ABC On ..........................................................................................................
Press the [ABC ON] button so that its indicator lights and the ABC
MODE pop-up screen appears. — The ABC mode is alternately turned
on and off each time the [ABC ON] button is pressed.
INTRO A/
FILL TO A
INTRO B/
FILL TO B
AUTO BASS CHORD
MAIN A
MAIN B
ENDING
SMALL
ABC
ABC ON
V Select an ABC Mode ......................................................................................
Before the ABC MODE pop-up screen disappears use the LCD buttons to select the SINGLE FINGER, FINGERED CHORD, or FULL
KEYBOARD ABC mode. The default mode is SINGLE FINGER, but
the mode you select is backed up even after the [POWER] switch is
turned off. Backup can be turned off via the Backup function — page
107.
B Start & Play ..............................................................................................................
Start playback by pressing the [START/STOP] button or by using the
[SYNCHRO] start mode.
● Single-finger Accompaniment
Pressing any key on the ABC section of the keyboard (up to the split
point — normally the F#2 key) will cause the automatic chord and
bass accompaniment to begin. If you press a “C” key, for example, a
C-major accompaniment will be played. Press another key in the
ABC section of the keyboard to select a new chord. The key you press
will always determine the “root” of the chord played (i.e. “C” for a C
chord). The name of the detected chord will appear on the display.
Detected chord
name
35
Auto Bass Chord (ABC)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Single-finger minor, seventh, and minor-seventh chords can be played
as follows:
Cm
• For a minor chord, press the root key and a black
key to its left.
C7
• For a seventh chord, press the root key and a
white key to its left.
Cm7
• For a minor-seventh chord, press the root key and
both a white and black key to its left.
● Fingered Accompaniment
As soon as you play any chord on the lower keyboard (up to the split
point — normally the F#2 key), the Clavinova will automatically begin to play the chord along with the rhythm and an appropriate bass
line. The name of the detected chord will appear on the display. “*”
will appear if the chord is not recognizable by the CVP-79A/69/69A/
59S.
• The automatic accompaniment will
sometimes not change when related
chords are played in sequence (e.g.
some minor chords followed by the
minor seventh).
The Clavinova will accept the following chord types in the Fingered
Accompaniment mode:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Major
Sixth [6]
Major seventh [M7]
Major seventh flatted fifth [M7(b5)]
Major seventh sharp eleventh [M7(#11)]
Added ninth [add9]
Major seventh ninth [M7(9)]
Six ninth [6(9)]
Flatted fifth [(b5)]
Augmented [aug]
Seventh augmented [7(#5)]
Major seventh augmented [M7(#5)]
Minor [m]
Minor sixth [m6]
Minor seventh [m7]
Minor seventh flatted fifth [m7(b5)]
Minor added ninth [madd9]
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Minor seventh ninth [m7(9)]
Minor seventh eleventh [m7(11)]
Minor major seventh flatted fifth [mM7(b5)]
Minor major seventh [mM7]
Minor major seventh ninth [mM7(9)]
Minor flatted fifth [m(b5)]
Diminished seventh [dim7]
Seventh [7]
Seventh suspended fourth [7sus4]
Seventh ninth [7(9)]
Seventh sharp eleventh [7(#11)]
Seventh added thirteenth [7(13)]
Seventh flatted fifth [7(b5)]
Seventh flatted ninth [7(b9)]
Seventh added flatted thirteenth [7(b13)]
Seventh sharp ninth [7(#9)]
Suspended fourth [sus4]
* A Fingering Chart is provided on page 123.
“On-bass” chords are also recognized. Two-note fingerings will produce a chord based on the previous chord.
“No chord” (i.e. rhythm only accompaniment) can be produced by
pressing any three consecutive keys (ex. C,C#,D) simultaneously.
“- - -” will appear instead of a chord name.
36
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
● Full-keyboard ABC
When this advanced auto-accompaniment mode is engaged the
Clavinova will automatically create appropriate accompaniment while
you play just about anything, anywhere on the keyboard: chords, a
bass line, arpeggiated chords, a melody line. The name of the detected
chord will appear on the display. You don’t have to worry about specifying the accompaniment chords. Although Full-keyboard ABC is
designed to work with many songs, some arrangements may not be
suitable for use with this feature. Try playing a few simple songs in
the Full-keyboard ABC mode to get a feel for its capabilities.
Auto Bass Chord (ABC)
• Chord detection occurs at approximately 8th-note intervals. Extremely
short chords — less than an 8th note
in length — may therefore not be
detected.
• The DUAL or SPLIT mode can be
used with ABC.
N Stop the Accompaniment ........................................................................
Press the [START/STOP] or [ENDING] button to stop the accompaniment.
START/STOP
TAP
INTRO A/
FILL TO A
INTRO B/
FILL TO B
SYNCHRO
START/STOP
AUTO BASS CHORD
MAIN A
MAIN B
ENDING
SMALL
ABC
• The [INTRO A/FILL TO A], [INTRO B/
FILL TO B], [MAIN A], [MAIN B], and
[ENDING] buttons can be used in the
ABC mode to create pattern variations
(refer to the “Accompaniment” section
on pages 30 and 32 for details).
ABC ON
Press the [ABC ON] button so that its indicator goes out when you
want to exit from the ABC mode.
Overall Accompaniment Volume Control
Use the ABC/SONG VOLUME control to adjust the volume of the
accompaniment sound in relation to the keyboard sound. No accompaniment sound will be produced if the MASTER VOLUME control is set
to its “MIN” position.
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
37
Auto Bass Chord (ABC)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Individual Part Volume Control
The CVP-79A/69/69A/59S has five accompaniment parts — RHYTHM,
BASS, CHORD, PAD, and PHRASE. — that function as follows:
RHYTHM
This is the main rhythm part. The RHYTHM part usually plays one
of the drum kits.
BASS
The BASS part always plays a bass line, but the voice will change
to fit the selected style … acoustic bass, synth bass, tuba, etc.
CHORD
This part provides the rhythmic chordal accompaniment required
by each style. You’ll find guitar, piano, and other chordal instruments here.
PAD
This part plays long chords where necessary, using sustained
instruments such as strings, organ, choir.
PHRASE
This is where the musical embellishments reside. The PHRASE
part is used for punchy brass stabs, arpeggiated chords, and other
extras that make the accompaniment more interesting.
The volume of the RHYTHM, BASS, CHORD, PAD, and PHRASE accompaniment parts can be individually adjusted via the volume parameters
accessed by the [MIXER] button. Select the part you want to control by first
pressing the appropriate LCD button, then use the data dial or [+]/[–] buttons
to set the volume as required. The normal volume level for any part (“90”)
can be instantly recalled by simultaneously pressing the [+] and [–] buttons
while the desired part is selected. Several parts can be selected at once by
pressing their buttons at the same time. The volume of all selected parts can
then be adjusted simultaneously. The mixer parameters will disappear when
the [MIXER] button is pressed a second time (or the [EXIT] button is
pressed).
FUNCTION
• The volume level can be adjusted
in two steps intervals.
MIXER
The second page of the MIXER display (accessed via the PAGE buttons)
includes individual volume parameters for the keyboard (manually played
sound) and harmony function sound — see page 41 for details on the Harmony function. There’s also a PRESET LCD button in this page which instantly resets all MIXER volume parameters to their default values (100 for
KBD part, and 90 for all other parts).
38
• Some styles may not use all five
parts.
Part volume relation:
• ABC/SONG volume is relative to
the MASTER VOLUME.
• Each RHYTHM, BASS, CHORD,
PAD or PHRASE part volume is
relative to ABC/SONG volume.
• KBD part volume is relative to
MASTER volume.
• HARMONY part volume is relative
to KBD part volume.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Auto Bass Chord (ABC)
Small ABC
A simple form of “orchestration” control is provided by the [SMALL
ABC] button. When this button is pressed so that its indicator lights
some of the accompaniment parts are turned off to create a simpler,
“smaller” accompaniment sound.
INTRO A/
FILL TO A
INTRO B/
FILL TO B
AUTO BASS CHORD
MAIN A
MAIN B
ENDING
SMALL
ABC
• ABC will not sound when the [ABC
ON] button is turned off, even if the
[SMALL ABC] button is turned on.
ABC ON
Press the [SMALL ABC] button a second time so that its indicator
goes out to turn the SMALL ABC function off.
Changing the ABC Split Point
The ABC split point can be set at any key by pressing the desired key
while holding the [ABC ON] button. The split point can also be set by
using the SPLIT POINT LCD button in the ABC MODE pop-up display, or the data dial or [+]/[–] buttons. The default split point — F#2 —
can be recalled by simultaneously pressing the [+] and [–] buttons.
ENDING
SMALL
ABC
• The split point is indicated by the keyboard guide lamp above the split point
key.
ABC ON
–
+
39
Auto Bass Chord (ABC)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Chord Assist
The Chord Assist function is essentially an electronic “chord book” that will show you appropriate
fingerings for chords you enter via the display. The fingerings are indicated via the keyboard guide lamps,
and correspond to those recognized in the ABC Fingered mode. You can also play chords on the keyboard
in the same way as in the ABC Fingered mode.
Z Select the Chord Assist Function ...................................................
Press the CHORD ASSIST LCD button in the ABC MODE pop-up
display.
X Start the Accompaniment .......................................................................
Start the accompaniment by using any of the methods described on
pages 30 and 31.
C Enter the Chord Root ...................................................................................
Press the ROOT LCD button to select the desired chord root, or use
the data dial or [+]/[–] buttons once the ROOT parameter is selected.
V Enter the Chord Type ....................................................................................
Use the TYPE ▲ and ▼ LCD buttons to select the chord type. The
data dial and [+]/[–] buttons can also be used once the TYPE parameter
is selected.
40
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Auto Bass Chord (ABC)
B Enter the Chord ..................................................................................................
The fingering for the chord selected via the LCD buttons will appear
on the keyboard guide lamps. At this point you can either play the indicated chord on the keyboard or press the ENTER LCD button to actually
enter the specified chord — i.e. the specified chord accompaniment will
sound.
• The chord name entered via the LCD
will appear in the TYPE and ROOT
parameter locations, while the actually
recognized chord name will appear
next to the keyboard symbol above the
parameters.
• A flashing keyboard guide lamp indicates a note which may be omitted.
N Rotate the Fingering as Necessary ..............................................
Press the ROTATE LCD button to shift the fingering down the keyboard. Each time the ROTATE button is pressed the next viable fingering
(inversion) appears on the guide lamps. The inversion number appears in
the ROTATE section of the display.
M Stop the Accompaniment ........................................................................
Press the [START/STOP] or [ENDING] button to stop the accompaniment.
< Exit When Done ..................................................................................................
Press the panel [ABC ON] button, so that its indicator goes out, to
exit from the Chord Assist function and ABC mode when done.
• The following chord types can be
specified via the Chord Assist display:
Maj, 7, m, m7, m7(b5), 6, m6, M7,
sus4, aug, m(b5), 7sus4, 7(#5), dim7,
(b5), 7(b5), mM7. All fingered-mode
chords (page 36) can be entered via
the keyboard.
• The split point is not shown on the
guide lamps when the Chord Assist
function is engaged.
• If the split point is set below F#2 it will
automatically be set at F#2.
Harmony
This feature automatically adds appropriate harmony notes or delayed decorative notes (up to three
notes) to a melody or chords you play on the keyboard. The harmony notes are produced to match chords
played via the ABC auto-accompaniment system.
Z Turn Harmony On .............................................................................................
Press the [HARMONY] button so that its indicator lights to turn the
HARMONY feature on.
• The Harmony feature cannot be turned
on when the Full Keyboard ABC mode
is selected.
STYLE
POP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
ROCK
COUNTRY
BALLAD
JAZZ
HARMONY
WALTZ
DISK
ONE TOUCH
SETTING
CUSTOM
41
Auto Bass Chord (ABC)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
X Select a Harmony Type ...............................................................................
While the HARMONY pop-up display is showing, use the data dial
or [+]/[–] buttons to select the desired harmony type. 16 harmony types
are available.
–
• With some harmony types the voice
used for the harmony will be different
from the currently selected voice.
+
Harmony Type List
• Duet
• Tremolo Oct
• Trio
• Strumming
• 4 Part
• Trio Delay
• 4 Part Jazz
• Vibes & J.Gtr
• Country
• Add Trp & Sax
• Octave
• Backing Vocal
• Tremolo
• Add Strings
• Tremolo Duet
• Forest
C Set Up ABC As Required ..........................................................................
Select an accompaniment style, tempo, and ABC mode (except Full
Keyboard).
V Start ABC Playback ........................................................................................
Start accompaniment playback using any of the methods described on
pages 30 and 31.
B Play ..................................................................................................................................
Play the required chords (single-finger or fingered chord) on the ABC
section of the keyboard while playing a melody line or chords on the
right-hand section of the keyboard. When chords are played on the righthand section of the keyboard, the harmony will be applied to the last note
played.
42
• The Harmony feature can be used
while ABC is off, but only octaves will
be produced.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Auto Bass Chord (ABC)
N Stop the Accompaniment ........................................................................
Press [START/STOP] or [ENDING] button to stop the accompaniment.
M Turn Harmony Off .............................................................................................
Press the [HARMONY] button again, so that its indicator goes out,
to turn the function off.
• Harmony can be turned on and off
while playing.
STYLE
POP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
ROCK
COUNTRY
BALLAD
JAZZ
HARMONY
WALTZ
DISK
ONE TOUCH
SETTING
CUSTOM
■ The Left Pedal & Harmony ......................................................................
If the Left Pedal Function is set to HARMONY ON/OFF (pages 27
and 93), harmonization of notes played on the right-hand section of the
keyboard only occurs while the left pedal is pressed. This allows you to
combine normal ABC type performance with harmony as required.
• The Left Pedal HARMONY ON/OFF
function is not effective when the HARMONY feature is off (i.e. the [HARMONY] button’s indicator is not lit).
CVP-79A
43
Auto Bass Chord (ABC)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
One Touch Setting
The CVP-79A internal styles each have 4 different preset “panel setups” that can be recalled via the
[ONE TOUCH SETTING] button to create different musical textures. The CVP-69/69A styles have 3,
and the CVP-59S styles have 1. The ONE TOUCH SETTING setups include settings for all of the following parameters:
One Touch Setting Parameter List
Accompaniment Parameters
Voice Parameters
• Voice
• Keyboard Volume
• Dual Mode
• Split Mode
• Dual Voice
• Split Voice
• Dual Balance
• Split Balance
• Dual Detune Depth
• Reverb On/Off
• Reverb Type
• Reverb Depth (Total,
Rhythm, Bass, Chord,
Keyboard)
• Effect On/Off
• Effect Type
• Effect Depth (Main
Voice, Dual Voice,
Split Voice)
• Right/1 Octave Shift
• Left Octave Shift
• 2nd Octave Shift
• Right/1 Pan
• Left Pan
• 2nd Pan
• ABC On
• Small ABC On/Off
• Harmony On/Off
• Harmony Type
• ABC/Song Volume
• Main A/B
• Tempo
• Rhythm Volume
• Bass Volume
• Chord Volume
• Pad Volume
• Phrase Volume
• Harmony Volume
ZEngage the One Touch Setting Feature ...................................
The ONE TOUCH SETTING feature can be used either while an
accompaniment is playing or prior to starting an accompaniment by simply pressing the [ONE TOUCH SETTING] button. The corresponding
panel setup is recalled immediately. On the CVP-79A and CVP-69/69A
other ONE TOUCH SETTING setups can also be recalled in the ONE
TOUCH SETTING pop-up display by using the SELECT ▲ and ▼ LCD
buttons.
STYLE
POP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
ROCK
COUNTRY
BALLAD
WALTZ
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
• To return to the settings that were
active prior to engaging the One Touch
Setting feature, re-select the style after
selecting a different style (ABC will
remain on however).
• The One Touch Setting feature cannot
be used when a [DISK/CUSTOM] style
is selected.
• ABC is automatically turned ON when
the One Touch Setting feature is engaged.
• The synchronized start mode is automatically turned ON if the One Touch
Setting feature is engaged before
starting the accompaniment.
CUSTOM
CVP-79A
X Adjust The Settings If Necessary ...................................................
Any of the parameters set by the ONE TOUCH SETTING feature can
be adjusted to create the desired sound after a ONE TOUCH SETTING
setup has been selected.
44
• If the STYLE SETTING parameter in
the BACKUP function (page 107) is set
to on, the One Touch Setting setup
selection for each style will be retained
in memory even when the power is
turned off. This way the desired setup
can be recalled immediately when the
[ONE TOUCH SETTING] button is
pressed. (CVP-79A/69/69A)
• Harmony will not be turned on if the
ABC Full Keyboard mode is selected,
even if the selected One Touch Setting
setup includes “Harmony ON”.
Custom Style
○○○○○○○○○○○○○○○○○○○○○○○○○○
The CVP-79A/69/69A/59S Custom Style feature allows you to
create original accompaniment styles that can be later recalled and
played at any time, just like the presets. Up to 8 custom styles can
be maintained in internal memory at the same time, and any number
can be saved to disk for later reloading and use.
The basic custom style recording procedure is outlined below.
• Custom style data is not retained in memory when the power is turned off, so be sure to
save your custom styles to disk before turning the power off.
• One pre-programmed temporary style is automatically loaded into the [DISK/CUSTOM]
memory whenever the power is turned on. (Memory is common to the Custom Styles and
the loaded styles from the optional Style File disks — page 55.)
DISK
STYLE
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
RECORD
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
CUSTOM
EXIT
–
REGISTRATION
+
REW
FF
2
3
ABC FREEZE
PAUSE
Z Engage the Custom Style Feature .................................................
Press the [DISK/CUSTOM] style selector so that its indicator lights,
then press the CUSTOM STYLE LCD button. The “Please select a
source STYLE.” message will appear on the display for a few seconds
before going to the CUSTOM STYLE page 1 display and the current
[DISK/ CUSTOM] style will begin playing.
STYLE
POP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
ROCK
COUNTRY
BALLAD
JAZZ
HARMONY
WALTZ
DISK
ONE TOUCH
SETTING
CUSTOM
X Select a Source Style ...................................................................................
Select a preset style that is close to the style you want to create. Preset
style selection is carried out in the normal way (page 28).
If you want to select a [DISK/CUSTOM] style, press the [DISK/
CUSTOM] style selector once again and use the STYLE ▲ and ▼ buttons, or the data dial or [+]/[–] buttons to select a [DISK/CUSTOM]
style.
45
Custom Style
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
C Select the Section You Want to Record ...................................
In the CUSTOM STYLE page 1 display, press the first LCD button as
many times as necessary to select the section you want to program first:
MAIN A, MAIN B, INTRO, FILL IN, or ENDING. The MAIN A section is initially selected.
Total measure number of
the selected section
Current measure number of
the selected section
Beat of the selected style
V Change the Time Signature & Number Of Measures,
If Required ................................................................................................................
If you want to create a style in a different time signature than the current style, or change the number of measures in the selected section,
Press the PAGE [>] button to go to CUSTOM STYLE page 2.
Current recording section and part
Use the BEAT LCD button to select a different time signature, or the
data dial or [+]/[–] buttons once the BEAT parameter has been selected.
As soon as you choose to change the beat value, the “Clear STYLE ?”
prompt will appear, since you will have to completely clear all sections
and parts of the style and start recording from scratch if you change the
time signature. Press OK to clear the style, or CANCEL to abort. Once
the style has been cleared you can select a new time signature as required: 2/4, 3/4, 4/4, or 5/4.
46
• In the CUSTOM STYLE, MAIN A,
MAIN B, INTRO, FILL IN or ENDING
are referred to as “section”, and
RHYTHM 1/2, BASS, CHORD 1/2,
PAD or PHRASE 1/2 are referred to as
“part”.
• Only one pattern can be created for
each INTRO, FILL IN and ENDING
section.
• Whether the “A” or “B” variations of the
INTRO, FILL IN and ENDING sections
are used as the source pattern depends on whether the MAIN A or MAIN
B section was selected when the Custom Style function was engaged. (As
for FILL IN, “FILL IN from A to A”, or
“FILL IN from B to B” is used.)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Custom Style
Use the MEAS. LCD button to select a different number of measures
for the selected section, or the data dial or [+]/[–] buttons once the
MEAS. parameter has been selected. As soon as you choose to change
the number of measures in the section, the “Clear SECTION ?”
prompt will appear, since you will have to clear all parts of the currently
selected section and start recording from scratch if you change the
number of measures. Press OK to clear the section, or CANCEL to abort.
Once the section has been cleared you can select a new number of measures as required: 1 through 8. The FILL IN section has only 1 measure
and the number of measures cannot be changed although the FILL IN
section can be cleared using this operation.
Once the BEAT and/or MEAS. parameters have been set as required,
press the PAGE [<] button to go back to the first custom style page.
B Select the Part & Voice You Want to Record ......................
Use the PART LCD button, the data dial, or [+]/[–] buttons to select
the part you want to record:
R1
Rhythm 1
R2
Rhythm 2
Bs
Bass
C1
Chord 1
C2
Chord 2
Pd
Pad
P1
Phrase 1
P2
Phrase 2
The R1 part is initially selected and set to the record mode.
Any part you select can be set to the record mode by using the rightmost
LCD button to select “REC” after selecting the part ( the part number
will appear white in a black box). Since parts other than R1 and R2 must
be cleared before they can be recorded (if the source style is a preset
style or a style loaded from the optional Style File disk) the “Clear
Part ?” confirmation will appear if you select a part that contains data:
press OK to clear the part and continue, or CANCEL to abort. Only one
part can be set to the record mode. All other parts will be set to “PLAY”
(part number surrounded by box) or turned “OFF” (part number only —
no box). Parts that contain no data are indicated by a dot in place of the
part number.
47
Custom Style
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
At this point you can also select the voice you want to record with
(the preset voice for that part will initially be selected). Only [DRUMS/
PERC.] voices can be used for the R1 part and only Drum Kit voices can
be used for the R2 part, while any other voices can be selected for the
remaining parts.
N Record the Selected part ..........................................................................
You can now add new parts to the selected part by playing the keyboard at the appropriate timing (play in C Major seventh since the Custom Style is recorded as a C Major seventh pattern). If you want to create
a totally new part from scratch, press the CLEAR LCD button to clear
the selected part before beginning to record. If both the R1 and R2 parts
are cleared the metronome will sound to provide a timing guide (the metronome sound is not recorded). When a drum kit voice is used, a single
drum instrument sound can be cleared from the R1 or R2 part by pressing the key corresponding to the instrument to be cleared while holding
the keyboard “CANCEL” (C1) key. The metronome timing guide can
also be cleared in this way.
• Playback can be started and stopped
via the [START/STOP] button as required while in the Custom Style mode
— data cannot be recorded while
playback is stopped.
• The timing guide will stop as soon as
the Custom Style is stored.
• The sound of all parts is automatically
stopped at the end of the style — i.e.
at the point between repeats when
recording. It is therefore not advisable
to record over this point.
Another useful recording aid is the SOLO LCD button: when this
button is pressed and highlighted, only the selected part will sound. Press
the SOLO button again to turn the solo function off and hear the entire
style.
M Quantize the Recorded Part, if Necessary ............................
You can “tighten up” the timing of a recorded part by aligning all
notes to specified beats via the PART QUANTIZE function in CUSTOM
STYLE page 2 (press the PAGE [>] button). Press the LCD button below the note symbol to select “quantize size” — i.e. the beats to which
the notes in the current part will be aligned:
32nd notes
3
16th note triplets
16th notes
3
8th note triplets
48
8th notes
3
quarter-note triplets
quarter notes
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Custom Style
• Quantization can only be applied to the
current recording part. Quantization
cannot be executed if no part is set to
the record mode.
Once the required quantize size has been selected press the START
LCD button to actually quantize the current part. Playback will stop for
an instant while the data is being quantized, then the START LCD button
will change to UNDO, allowing you to undo the quantize operation and
return to the pre-quantized data if the results are not as you expected.
You will not be able to UNDO once another button has been pressed.
< Repeat Until the Custom Style is Complete ........................
Repeat steps 3 through 7 until all parts or all sections have been recorded as required.
• During Custom Style recording, no
MIXER display is available.
> Name the Custom Style .............................................................................
When your custom style is complete, use the PAGE buttons to select
CUSTOM STYLE page 3, and press the STYLE NAME LCD button to
go to the style naming page.
The current style name appears in the upper right corner of the display. Use the > LCD button to position the underline cursor at the character you want to change (style names can be up to 12 characters in
length). Use the data dial and/or the [+]/[–] buttons to select the character you want to enter from the list in the center of the display, then press
the c.set LCD button to enter the character at the current cursor position. Repeat this procedure until your name is complete. The c.del LCD
button can be used to back up one space and delete a character.
When the name is complete press the OK LCD button to register the
name for the current custom style, or CANCEL to abort.
49
Custom Style
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
? Store the Custom Style ..............................................................................
Press the STORE LCD button in CUSTOM STYLE page 3 to store
the current custom style in the internal memory. The “Store
XXXXXXXX?” confirmation prompt and MEMORY No. parameter
will appear (“XXXXXXXX” is the style name). Use the MEMORY No.
▲ and ▼ LCD buttons to select the memory number — 1 through 8 —
to which you want to store the custom style, then press OK to store or
CANCEL to abort.
• The tempo setting at the time the
Custom Style is stored becomes the
preset tempo for that style.
• If the selected memory number already
contains a style, the style name will
appear next to the memory number.
The existing style will be overwritten
when a new style is stored.
[ Exit When Done ..................................................................................................
Press the [EXIT] button to exit from the Custom Style mode and return to the normal play mode.
EXIT
• Custom style data is not retained in
memory when the power is turned off,
so be sure to save your custom style
before turning the power off — see
“Save to disk” on page 52.
Other Custom Style Functions
In addition to the various functions described in the basic custom style recording procedure, above, the
CUSTOM STYLE display pages include several other functions that you may find useful when creating
custom styles.
■ Recall Section ......................................................................................................
This function makes it possible to recall the last-stored version of the
currently selected section (all parts of the section are recalled). Simply
press the RECALL SECTION LCD button in CUSTOM STYLE page 2.
If the recall operation can’t be carried out (i.e. The time signature has
been changed), the “Can’t recall!” alert display will appear. If this
happens press OK to return to the previous display.
50
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Custom Style
■ Style Clear ................................................................................................................
Press the STYLE CLEAR LCD button in CUSTOM STYLE page 3 to
entirely clear the current custom style. The “Are you sure?” confirmation prompt will appear. Press YES to clear the style or NO to abort.
■ Volume & Effects ...............................................................................................
CUSTOM STYLE page 4 includes a range of parameters that let you
individually set the volume, reverb, effect, and pan for each part of each
custom style section. Use the SECT. parameter to select the section (or
“ALL” sections), and the PART parameter to select the part (or “ALL”
parts). The third LCD button selects VOLUME, REVERB, EFFECT or
PAN, and the VALUE (or DEPTH) parameter sets the amount or depth.
When VOLUME is selected the SECT. parameter is fixed at “ALL” and
the VALUE range is from –50 to +50, relative to the preset volume of the
source style. The REVERB and EFFECT DEPTH ranges are from 0 to
100. The PAN VALUE settings are L10 (full left) … C (center) … R10
(full right). When EFFECT is selected the TYPE parameter appears and
you can also select the effect type via the TYPE LCD button. The available effect types are listed below.
• Normally the preset VALUE and EFFECT TYPE are initially selected. If
PART is set to “ALL”, the R1 part
preset values are displayed. If SECT.
is set to “ALL”, the MAIN A preset
values are displayed.
Effect Type List
•
•
•
•
•
•
CHORUS 1
CHORUS 2
CHORUS 3
CELESTE 1
CELESTE 2
CELESTE 3
•
•
•
•
•
FLANGER 1
FLANGER 2
SYMPHONIC (CVP-79A only)
PHASER (CVP-79A only)
OFF
• Effect type “OTHERS” may appear if
the preset effect type is other than that
of what is in the list.
51
Custom Style
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
■ Save to Disk ............................................................................................................
A complete set of 8 custom styles or individual custom styles can be
saved to disk via CUSTOM STYLE page 5.
After making sure that a properly formatted disk is inserted in the
Clavinova disk drive (page 98), use the MEMORY No. ▲ and ▼ buttons to select the memory number of the custom style you want to save
to disk, or “ALL” if you want to save a complete set of 8 custom styles.
When this is done, press the SAVE LCD button to start saving the data to
disk. At this point the name entry display will appear and you can enter a
name for the Custom Style disk file in the same way as you entered a
name for the Custom Style itself (page 49). Press SAVE when the name
has been entered. If a file with the same name already exists the “Same
name! Overwrite?” confirmation prompt will appear. Press OK to
overwrite the existing file or CANCEL to abort.
• Saved Custom Style files can be
loaded via the “STYLE FILE LOAD”
function described in the “Style File
Load” section (page 55).
• A single floppy disk can hold up to 60
song files (page 72) and 60 style files
(the total number of files however, is
approximately 110 files).
Your custom styles must be stored to internal memory before they can
be saved to disk (see step 10 of the basic custom style recording procedure). If a custom style has not been stored and you attempt to save it to
disk, the “Please store before saving” alert display will appear.
If this happens press OK to return to the previous display (CUSTOM
STYLE page 3), store the custom style, then try saving again.
Press the [EXIT] button to exit from the Custom Style mode and return to the normal play mode.
Playing Back Your Custom Styles
Once created, your original custom styles can be selected for playback by pressing the [DISK/CUSTOM] button (its LED will light), and
then using the STYLE ▲ and ▼ LCD buttons — or the data dial or [+]/
[–] buttons — to select the custom style you want to play. The selected
style can then be played and used with ABC auto accompaniment in exactly the same way as the preset styles (page 28).
52
• Since only one type of INTRO, FILL IN,
and ENDING section can be recorded
for each Custom Style, no “A/B” variations are produced during playback.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Custom Style
Custom Style Alert & Error Displays
The following alert and error displays may appear in the corresponding situations.
■ Insufficient Memory To Store ..............................................................
This alert message will appear if there is not enough memory to perform a store operation.
In this case it will be necessary to either delete a style you don’t need
or simplify the style you are currently recording. Press CANCEL to return to CUSTOM STYLE page 1, at which point you can simplify the
current style (by clearing a part, etc.), or DELETE to go to the “Delete
STYLE ?” display:
Use the MEMORY No. ▲ and ▼ buttons to select the number of the
style you want to delete, then press OK to delete the style, or CANCEL
to abort.
• The amount of memory being used for
the selected style is also shown on the
display (in approximate kilobytes) so
as to set up the approximate standard
which style to delete in relation to the
total 160 KB memory space.
■ Memory Full During Recording .........................................................
This alert message will appear if the memory becomes full during
recording or editing.
Press OK to return to CUSTOM STYLE page 1 and simplify the style
by clearing a part, etc.
53
Custom Style
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
■ Exit Before Store ........................................................................................................
If you press [EXIT] button to exit from the Custom Style function before
storing the style the following display will appear.
Select a memory number and press YES to store the style and then exit,
press NO to exit without storing the style, or press CANCEL to return to the
Custom Style mode.
■ Style Change Before Store ..............................................................................
If you attempt to select a different source style before storing the current
style you recorded, the following display will appear.
• If you want to select a different
source style without storing the
current style, exit from the CUSTOM STYLE mode without storing
the style (see “Exit Before Store”
above), and then re-enter the
CUSTOM STYLE mode.
Select a memory number and press OK to store the style and then select
the new source style, or press CANCEL to return to the Custom Style mode.
■ Too Many Files ..............................................................................................................
A single floppy disk can hold up to 60 style files. If you attempt to save
more the following display will appear.
Press OK to clear the display, then prepare a new disk and save the file(s).
■ Disk Full ...............................................................................................................................
If the current disk becomes full during a save operation the following
display will appear.
Press OK to clear the display, then either delete any unwanted song files
or other files from the disk, or prepare a new disk.
54
• Style files cannot be deleted from
the disk.
Style File Load
○○○○○○○○○○○○○○○○○○○○○○○○○
Style files from optional Yamaha “Style File” disks, or disks containing
custom style files you’ve created yourself, can be loaded into the
CVP-79A/69/69A/59S and played as required.
• Loaded disk styles will be retained in memory only until the power is turned off.
• One pre-programmed temporary style is automatically loaded into the [DISK/CUSTOM]
memory whenever the power is turned on.
DISK
STYLE
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
RECORD
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
EXIT
–
REGISTRATION
+
CUSTOM
REW
FF
2
3
ABC FREEZE
PAUSE
Loading Disk Styles
Z Insert the Style Disk ......................................................................................
Insert the Style File Disk into the disk drive with the sliding door on
the disk facing the drive slot and the label side facing upward. The disk
should click into place and the disk lamp will light briefly while the
Clavinova reads and identifies the disk. When an appropriate Style File
disk is inserted, the STYLE FILE LOAD display (see step 2 below) will
appear automatically. If the disk is already inserted and the STYLE FILE
LOAD display is not showing, press the [DISK/CUSTOM] selector to
call the DISK/CUSTOM STYLE display and press the LOAD SINGLE
button.
• The “No disk!” alert will appear if no
disk is currently inserted.
• The “No file!” alert will appear if the
currently inserted disk contains no
style files.
• If a disk containing both song and style
files is loaded, the SONG PLAY mode
will automatically be selected. In this
case press the SONG [PLAY] button
so that its indicator goes out to exit
from the SONG PLAY mode, then
press the [DISK/CUSTOM] button.
55
Style File Load
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
A set of 8 files saved by using the Custom Style save “ALL” function
(page 45) can be loaded by pressing the ALL LOAD LCD button rather
than the LOAD SINGLE button. The rest of the ALL LOAD procedure is
essentially the same as the LOAD SINGLE procedure, as follows.
X Select a Style File .............................................................................................
Use the STYLE FILE ▲ and ▼ LCD buttons — or the data dial or
[+]/[-] buttons — to select the desired style file.
You can “preview” the selected style by pressing the LISTEN LCD
button (the “LISTEN” function is not available in the ALL LOAD display).
• If a tempo is set prior to loading the
style, that tempo becomes the default
for the loaded style.
• Some styles are too large for the LISTEN function. In this case the “Too
much data for listen! Please [LOAD].”
alert display will appear. In this case
load the style directly as in step 3.
• ABC is automatically turned on when
the LOAD SINGLE button is pressed
and the style is played back automatically with the ABC accompaniment in
C Major when the LISTEN LCD button
is pressed. You can also change the
chord or try playing on the keyboard if
you like.
Press the LISTEN LCD button again or the [START/STOP] button
to stop listening.
C Select a Memory Number & Load the Style .........................
Use the MEMORY LCD button to select the memory number to
which the selected style file is to be loaded (1 through 8), then press the
LOAD LCD button to load the style file.
Repeat Step 2 and 3 to select and load more style files as you like.
It is not necessary to select a memory number when ALL LOAD is
selected in step 1. Simply press OK to load or CANCEL to abort.
If there is not enough memory to load the specified file the “Not
enough memory! Delete an unneeded STYLE ?” alert display will appear. In this case it will be necessary to delete a style you
don’t need before loading the new style. Use the MEMORY No. ▲ and
▼ buttons to select the number of the style you want to delete, then press
DELETE to delete the style, or CANCEL to abort.
56
• If the selected memory number already
contains a style, the style name will
appear on the display. The existing
style will be overwritten when a new
style is loaded.
• The ALL LOAD display is as follows:
When ALL LOAD is executed, all data
in the eight memories will be replaced
by new data.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Style File Load
• The amount of memory being used for
the selected style is also shown on the
display (in approximate kilobytes) so
as to set up the approximate standard
which style to delete in relation to the
total 160 KB memory space.
V Eject the Disk When Done ......................................................................
When you’ve finished with the Style File disk, press the disk drive
EJECT button to remove it and return to the normal play mode display.
You can return to the normal play mode without removing the disk by
pressing the [EXIT] button or a STYLE selector.
• The disk drive lamp will light while the
style is being loaded. NEVER attempt
to remove a disk while the drive lamp
is lit.
• The LISTEN, LOAD, [EXIT] and style
buttons will not function while the style
data is being loaded (i.e. while the disk
drive lamp is lit).
Using Loaded Style Files
Once loaded, style files can be selected for playback by pressing the
[DISK/CUSTOM] button (its LED will light), and then using the
STYLE ▲ and ▼ LCD buttons — or the data dial or [+]/[–] buttons — to
select the style you want to play. The selected style can then be played
and used with ABC auto accompaniment in exactly the same way as the
preset styles (page 28).
STYLE
POP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
ROCK
COUNTRY
BALLAD
JAZZ
HARMONY
WALTZ
DISK
ONE TOUCH
SETTING
CUSTOM
57
Registration Memory
○○○○○○○○○○○○○○○○○○○○○
The Registration Memory feature can be used to memorize a
number of complete control-panel setups that you can recall whenever needed. 25 in the CVP-79A and CVP-69/69A (5 banks x 5
memories), and 15 in the CVP-59S (3 banks x 5 memories).
REGISTRATION
STYLE
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
VOICE
RECORD
PLAY
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
MEMORY
BANK
1
CUSTOM
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
EXIT
–
REGISTRATION
+
REW
FF
2
3
ABC FREEZE
PAUSE
Z Set Up the Controls as Required .....................................................
Make the desired control settings. The following settings are memorized by the Registration Memory function:
Data Stored By the Registration Memory
Voice parameters
•
•
•
•
•
•
•
•
•
•
•
•
•
Voice
Keyboard Volume
Split Point
Dual Mode
Split Mode
Dual Voice
Split Voice
Dual Balance
Split Balance
Dual Detune Depth
Reverb On/Off
Reverb Type
Reverb Depth (Total, Rhythm,
Bass, Chord, Keyboard)
• Effect On/Off
• Effect Type
• Effect Depth (Main Voice, Dual
Voice, Split Voice)
• Touch Sensitivity
• Left Pedal Function
• Right/1 Octave Shift
• Left Octave Shift
• 2nd Octave Shift
• Right/1 Pan
• Left Pan
• 2nd Pan
• Transpose
• Damper Range
• Damper Mode (CVP-79A only)
Accompaniment parameters
•
•
•
•
•
•
•
•
58
ABC Mode
ABC On/Off
Small ABC On/Off
Harmony On/Off
Harmony Type
ABC/Song Volume
Style
Main A/B
•
•
•
•
•
•
•
Tempo
Rhythm Volume
Bass Volume
Chord Volume
Pad Volume
Phrase Volume
Harmony Volume
2
3
4
5
ABC FREEZE
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Registration Memory
X Select a Registration Bank (if necessary) .............................
Any of the 5 or 3 Registration Memory banks can be selected by
pressing the [BANK] button and selecting the desired bank via the popup display LCD buttons (A through E in the CVP-79A/69/69A, and A
through C in the CVP-59S).
REGISTRATION
MEMORY
BANK
1
2
3
4
5
ABC FREEZE
CVP-79A/69/69A
C Register the Settings ....................................................................................
While holding the [MEMORY] button, press one of the [REGISTRATION] buttons. Any data that was previously in the selected location is erased and replaced by the new settings. The corresponding Registration Memory number will appear next to the “R” symbol in the display.
REGISTRATION
MEMORY
BANK
1
2
Registration Memory number
3
4
5
ABC FREEZE
• Registration backup is normally enabled, so the registration data is retained in memory even when the
power is turned off. If registration
backup is turned off via the “Backup”
function described on page 107, all
registration data will be initialized to
the factory-preset settings when the
power is turned off.
• Factory-preset data is provided for all
registration banks and memory locations.
• Complete sets of registration data can
be saved to and loaded from disk as
described on page 99.
59
Registration Memory
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Recall the Registered Panel Settings
Simply select the appropriate bank as described above, then press the
desired [REGISTRATION] button at any time to recall the memorized
settings. The corresponding Registration Memory number will appear
next to the “R” symbol in the display.
A pencil (edit) symbol will appear next to the registration number in
the display as soon as any change is made to the panel settings. In other
words, if the pencil symbol is showing, the current panel settings are
different from those stored in the memory.
REGISTRATION
MEMORY
BANK
1
2
3
4
5
• Selecting only a different bank will not
change the registration settings. The
registration settings are recalled only
when the [REGISTRATION] button is
pressed.
• If the Left Pedal function is set to “Registration+” (pages 27 and 93), the left
pedal can be used to step through the
registration memory locations so a
completely different set of panel settings can be recalled each time the
pedal is pressed.
ABC FREEZE
Registration Memory number
edit symbol
The ABC Freeze Function
When the ABC FREEZE function is engaged, the accompaniment
parameters listed above will not be changed when a registration memory
is recalled. This allows you to recall different registration memory settings while using Auto Accompaniment, without suddenly disturbing the
flow of the accompaniment. The ABC FREEZE function is turned on
and off by pressing the [ABC FREEZE] button. The [ABC FREEZE]
indicator lights when it is turned on.
REGISTRATION
MEMORY
60
BANK
1
2
3
4
5
ABC FREEZE
• ABC Freeze remains on even if a
different registration bank is selected.
Disk Orchestra Collection &
Song Playback
○ ○ ○ ○ ○ ○ ○ ○
The CVP-79A/69/69A/59S can play back songs you’ve recorded yourself using
the song recorder function described in the next section, and songs on optional
Yamaha Disk Orchestra Collection disks (one is supplied with the Clavinova).
With Disk Orchestra Collection (“DOC”) disks the Clavinova will let you enjoy
listening to automated performances, or function as your “private music tutor,”
allowing you to practice various parts of a piece while the others are played
automatically. The CVP-79A/69/69A/59S also shows you which keys to play with
keyboard guide lamps that light up above each key. You can also play “in
ensemble” with the complete Disk Orchestra Collection arrangement.
Different displays will appear depending on the type of data being played. But any type of data can be
played back by following the operation procedure described below. Also refer to the “Playing Other
Types of Music Data” section on page 71.
• Playback data is not transmitted via the MIDI OUT connector.
SONG
PLAY
STYLE
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
RECORD
RECORD
GUIDE
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
EXIT
–
REGISTRATION
+
REW
FF
2
3
ABC FREEZE
PAUSE
SONG CONTROL
REW
FF
PAUSE
Straight Playback
Z Engage the Song Play Mode ................................................................
The Song Play mode is engaged automatically when a song disk is
inserted in the disk drive. Insert a disk containing songs you’ve recorded
yourself or a DOC disk into the disk drive with the sliding door facing
the drive slot and the label side facing upward. The disk should click into
place and the disk lamp will light briefly while the Clavinova reads and
identifies the disk. Once the disk has been identified the SONG PLAY
[MAIN] display will appear and the [PLAY] button indicator will light.
If a song disk is already inserted but the Song Play mode is not engaged, press the [PLAY] button so that its indicator lights and the SONG
PLAY [MAIN] display (SONG PLAY page 1) appears.
SONG
PLAY
DOC
RECORD
GUIDE
Original song
61
Disk Orchestra Collection & Song Playback
○○○○○○○○○○○○○○○○○○○○○○○○○○
X Select a Song Number ................................................................................
The current song number and name will be shown on the display
along with the currently selected tempo. Use the SONG LCD button to
select the desired song number, or the data dial or [+]/[–] buttons. Select
“ALL” if you want all songs on the disk to be played in order and repeated until playback is stopped, or “RANDOM” to play back all songs
on the disk in random order until playback is stopped.
DOC
Keyboard voice
Selected song
number and name
• If you select a song in display page 1
or 4, and then select 1 SONG repeat
mode in page 2, only the selected
song will be played back repeatedly
until stopped.
Original song
Another convenient way to select a song for playback is to use the
PAGE buttons to go to page 4 — SONG PLAY [LIST] — and use the
data dial or [+]/[–] buttons to select a song from the list that appears on
the display. Up to 8 song titles are shown on the LCD at a time. If more
songs are on the disk, the next 8 titles will appear when you scroll past
the last title shown on the LCD.
C Start/Stop Playback .......................................................................................
Start playback of the selected song by pressing either the START
LCD button or the panel [START/STOP] button. Unless “ALL” or
“RANDOM” is selected, the selected song will play through to the end
and playback will stop automatically. The current measure number and
tempo will be shown on the display during playback.
Playback can be stopped at any time by pressing the STOP LCD button (the START LCD button changes to a STOP button once the playback has started) or the panel [START/STOP] button.
You can exit from the song play mode by pressing the [PLAY] button
so that its indicator goes out, or by pressing the [EXIT] button.
62
• If you first select “ALL” in display page
1, and then select a song in display
page 4, all songs will be repeatedly
played back starting from the selected
song.
• During Disk Orchestra Collection playback the left- and right-hand voice can
be changed by using the normal voice
selection procedure (page 15). In this
case the selected voice also becomes
the keyboard voice. The selected
voice is shown in the SONG PLAY
page 1 display.
• When playing back a song recorded on
the Clavinova, only the keyboard voice
can be changed. The keyboard voice
name is shown in the SONG PLAY
page 1 display.
• Please note that playback may not
immediately start while the Clavinova
is searching the disk for a selected
song after the START LCD button or
the panel [START/STOP] button is
pressed.
• With some songs the displayed measure numbers may not match those
marked on the score.
• Some songs start after a click count-in.
• The playback tempo can be changed
freely as required. The preset tempo
for the selected song can be recalled
at any time by pressing the TEMPO [+]
and [–] buttons simultaneously.
• Some Disk Orchestra software does
not produce a tempo display (e.g. freetempo phrases, etc.). In this case,
“- - -” will appear in place of the tempo
on the display, and the measure numbers shown on the display will not
match the actual measure numbers of
the song.
• The keyboard guide lamps corresponding to the keys being played by
the RIGHT and LEFT part (or PART 1
and PART 2) will light in real time. The
keyboard guide lamps can be turned
off via the LAMP LCD button in SONG
PLAY display page 3.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Disk Orchestra Collection & Song Playback
DOC
Original song
V Eject the Disk When Done .......................................................................
When you’ve finished with the currently loaded disk, simply press the
disk drive EJECT button to remove it.
• NEVER eject a disk or turn the power
off while:
1. The disk drive lamp is on.
2. A song is playing.
Playing Back Specific Parts
The RIGHT, LEFT, and ORCH LCD buttons (PART 1, PART 2, and OTHERS when an original song
disk is being played) can be used to turn playback of the corresponding parts on or off. The buttons are
highlighted when the parts are turned on. Use these buttons to select the parts you want to play back. You
can, for example, turn off the right and/or left-hand parts so you can practice them on the keyboard. When
an original song disk is being played, the tracks turned on and off by the PART 1 and PART 2 buttons can
be specified via the SONG PLAY [PART ASSIGN] display (SONG PLAY page 6), described below. The
default settings are: PART 1 = Track 1, PART 2 = Track – – (off).
● Turning Individual Orchestra Parts On or Off
Normally the ORCH (or OTHERS) LCD button turns all the orchestra
parts (tracks 3 through 10 and the rhythm tracks), or all parts other
than parts 1 and 2 on or off at once. You can, however, turn these parts
on or off individually via the SONG PLAY [TRACK PLAY] display
(SONG PLAY page 5).
DOC
• When playing back Disklavier
PianoSoft disks (see “Playing Other
Types of Music Data”, page 71) only
the RIGHT or RIGHT and LEFT LCD
buttons will appear.
Original song
63
Disk Orchestra Collection & Song Playback
○○○○○○○○○○○○○○○○○○○○○○○○○○
Z Select the TRACK PLAY Page ..............................................................
Use the PAGE buttons to select page 5 — the SONG PLAY [TRACK
PLAY] display. The numbers of tracks which contain data are shown
above the TRACK LCD buttons. Tracks which are enabled for playback
are indicated by a box surrounding the track number. Tracks which do
not contain data appear as dots.
X Mute, Play-enable, or Solo Tracks as Required ...............
Use the TRACK < and > buttons to select a track (an underline cursor appears under the selected track). The data dial and [+]/[–] buttons
can also be used to select tracks. Use the PLAY/OFF button to mute
(turn off) or play-enable the selected track. The track number box disappears when the track is muted. Any number of tracks can be muted at the
same time to leave on the tracks you want to hear play-enabled. The
voice used by the currently selected track is shown above the PLAY/
OFF button.
Select a track and press and highlight the SOLO LCD button to hear
only the selected track. Press the SOLO LCD button again to disengage
the solo function.
64
• All track numbers appear whether the
tracks contain data or not when a
Standard MIDI file song (see “Playing
Other Types of Music Data”, page 71)
other than the original song is selected.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Disk Orchestra Collection & Song Playback
Part Assignment for Original Song Playback
Before an original song disk is played, specify the tracks to be turned on and off by the PART 1 and
PART 2 LCD buttons via the SONG PLAY [PART ASSIGN] display.
Use the PAGE buttons to select the SONG PLAY [PART ASSIGN]
display (SONG PLAY page 6), then use the PART 1 and PART 2 parameters to assign the desired tracks to the corresponding parts. For
either part the corresponding ▲ and ▼ buttons can be used to select a
track, or the data dial or [+]/[–] buttons can be used once the parameter is
selected.
• The [PART ASSIGN] display will not
appear when Disk Orchestra Collection
or Disklavier data (see “Playing Other
Types of Music Data”, page 71) is
being played.
The default settings are: PART 1 = Track 1, PART 2 = Track – – (off).
Tracks 1 through 16 can be selected for both parts 1 and 2, and part 2 can
additionally be turned off. The same track cannot be assigned to both
parts.
Overall Song Playback Volume Control
The ABC/SONG VOLUME control can be used to control the overall volume of song playback. Whenever a song is first selected, however,
the maximum volume setting (=standard volume level setting) is recalled
regardless of the position of the ABC/SONG VOLUME control. The
song playback volume can then be adjusted as required.
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
• If ABC is turned on during the playback
of an original song that was recorded
without ABC, the ABC/SONG VOLUME control will affect the ABC sound
rather than the song playback sound.
• ABC cannot be used during playback
of a song recorded with ABC or Disk
Orchestra Collection playback.
65
Disk Orchestra Collection & Song Playback
○○○○○○○○○○○○○○○○○○○○○○○○○○
Individual Part Volume Control & Voice Selection
Press the [MIXER] button while in the Song Play mode to access the song playback volume parameters, and the voice selection parameter for the left- and right-hand voice when a Disk Orchestra Collection
disk is being played. The MIXER display will disappear when the [MIXER] button is pressed a second
time, or when the [EXIT] button is pressed.
■ Disk Orchestra Collection Disk Playback ..............................
During Disk Orchestra Collection playback the MIXER display has
two pages. Page 1 includes the L&R volume and L&R VOICE parameters. Use the L&R LCD button — or the data dial or [+]/[–] buttons
once the L&R parameter has been selected — to set the volume of the
left- and right-hand voice. Use the L&R VOICE ▲ and ▼ LCD buttons
or the data dial or [+]/[–] buttons once the L&R VOICE parameter has
been selected to select the voice used for the left- and right-hand parts.
Page 2 of the MIXER display includes independent volume parameters
for the RHYTHM, BASS, ORCH (orchestra), and KBD (keyboard) parts,
and a PRESET LCD button that resets all volume parameters to “100”.
Any of the volume parameters can be selected and incremented by using
the corresponding LCD button, or the data dial or [+]/[–] buttons can be
used to increment or decrement the currently selected volume parameter.
Press the [+] and [–] buttons simultaneously to recall the default (“100”)
volume setting. Several parts can be selected at once by pressing the corresponding LCD buttons at the same time. The volume of all selected
parts can then be adjusted simultaneously.
66
• When playing back Disklavier
PianoSoft disks (see “Playing Other
Types of Music Data”, page 71) only
the L&R VOICE LCD buttons will appear.
• The voice change for the left- and
right-hand parts by this operation does
not affect the keyboard voice. But if
you press the panel [VOICE] button,
the result will be both the keyboard
voice and the left- and right-hand part
voice being changed simultaneously.
• When a different song is selected the
voice and volume settings will be reset
to the default settings.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Disk Orchestra Collection & Song Playback
■ Original Song Disk Playback ...............................................................
During original song disk playback the MIXER display has 5 pages.
The first four pages include independent volume parameters for each of
the 16 song tracks. Page five includes the KBD (keyboard) volume parameter and a PRESET LCD button. The volume parameters are adjusted
in the same way as described above.
• If ABC is turned on during the playback
of an original song that was recorded
without ABC, the MIXER display will
function as the ABC part volume control rather than the song part volume
control.
Guided Right- and Left-hand Practice
With this feature, the Clavinova indicates the notes to play via the keyboard guide lamps and waits for
you to play the appropriate keys before playing ahead, so you can learn to play the piece at your own pace.
The guide lamps can be turned on or off as required. Two guide modes are provided:
● Next Note:
In this mode the guide lamps of the Clavinova indicate in advance,
which note(s) you will have to play next. If you miss the correct timing, the lamp(s) will start to flash while the Clavinova will wait until
you play the correct keys. Only then the guide lamp(s) for the next
note(s) will light up and you can quickly move your hands to the corresponding area on the keyboard. This is the default guide mode.
● Sound:
Both the keyboard guide lamps and sound are used to guide you to the
proper notes. In the Sound mode the Clavinova will play ahead for
approximately one phrase and then wait until the appropriate notes, as
indicated by the keyboard guide lamps, are played. If the appropriate
notes are not played for a few seconds, the Clavinova will automatically play and repeat the phrase until it is played properly. This is an
excellent way to learn to associate the keys with the notes they produce.
• When playing back the internal RAM
data (see “Recording Without a Disk”,
page 89) or the Standard MIDI File
format 1 data (see “Playing Other
Types of Music Data”, below) “- - -” will
appear in the GUIDE MODE parameter location and only the current notes
to be played will be shown on the
keyboard guide lamps — i.e. the “next
notes” will not appear.
• The GUIDE MODE cannot be changed
during playback.
• When the DOC song recorded for the
special guide mode is selected, the
special guide mode for that song will
be automatically engaged — in this
case neither of the NEXT NOTE or
SOUND sections will be highlighted.
But you can re-select the NEXT NOTE
or SOUND mode by pressing the
corresponding LCD button. (The NEXT
NOTE or SOUND mode cannot be reselected when not at the beginning of
a song or when the PHRASE REPEAT
or A-B REPEAT mode (page 69) is
engaged.)
67
Disk Orchestra Collection & Song Playback
○○○○○○○○○○○○○○○○○○○○○○○○○○
The GUIDE display appears automatically when the [GUIDE] button
is pressed to turn the guide function on. If the guide function is already
on, the PAGE buttons can be used to select the SONG PLAY [GUIDE]
display (SONG PLAY page 3). Use the GUIDE MODE NEXT NOTE or
SOUND LCD button to select the desired guide mode. The settings of
the RIGHT and LEFT LCD buttons (or PART 1 and PART 2) in the
SONG PLAY [MAIN] display (SONG PLAY page 1) will then determine whether the guide function operates for the left-hand part (part 2)
only, the right-hand part (part 1) only, or both parts, as shown below.
SONG
PLAY
RECORD
GUIDE
Left- and right-hand guide
Right-hand guide only
Left-hand guide only
When you press the [START/STOP] button or the START LCD button in the SONG PLAY [MAIN] display (SONG PLAY page 1) to begin
playback, the introduction will play automatically but then the Clavinova
will stop and wait for you to play the correct note(s). The CVP-79A/69/
69A/59S indicates the key(s) to be played via the guide lamps above the
keyboard. As you play the appropriate notes, the piece will continue,
pausing until you play the right notes each time.
If the guide lamps flashing above the keyboard distract you, or you
want to try playing along without them, simply press the LAMP LCD
button in the SONG PLAY [GUIDE] display to turn the lamps “OFF”.
Repeat to turn the guide lamps back on.
As with regular playback, the song will stop automatically when the
end is reached, or it can be stopped at any time by pressing the STOP
LCD button in the SONG PLAY [MAIN] display (SONG PLAY page 1)
or the panel [START/STOP] button.
Press the [GUIDE] button so that its indicator goes out when you
want to turn the guide function off.
68
• When the guide function is turned off
(i.e. the [GUIDE] button indicator is off)
and the SOUND mode is selected, the
guide lamps light in real time corresponding to the notes played by the
left- and right-hand parts, when both
the left- and right-hand parts are either
on or off.
If one or the other of the parts is off,
the guide lamps correspond only to the
part that is turned off.
When the guide function is turned off
and the NEXT NOTE mode is selected, both the current (flashing) and
next notes (continuously-lit) are shown
by the guide lamps if either or both
parts are turned off. (If both parts are
turned on, only the current notes are
shown by the guide lamps.)
• The guide part can be selected, the
guide LAMP can be turned on and off,
and the guide function itself can be
turned on and off during playback.
• Playback tempo can be set to any
desired value after a song has been
selected by using the TEMPO [+] and
[–] buttons.
• The positions of the guide lamps do
not change if the transpose function is
used to transpose the pitch of the
keyboard.
• The [ o PAUSE], [ r REW] and [ f FF]
buttons will not operate during playback when the guide function is in use.
• The guide function may not work properly with software which was not produced for independent left- and righthand playback.
• Since the guide “phrases” used in the
SOUND mode are automatically determined by the Clavinova, they may not
precisely match the actual musical
phrases. Also, the phrases may become shorter when the guide function
is used for both the left- and right-hand
parts.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Disk Orchestra Collection & Song Playback
Repeat Functions
The CVP-79A/69/69A/59S has a range of repeat functions that can be useful aids for learning to play difficult passages. The repeat modes are all accessible via the SONG PLAY [REPEAT] display (SONG PLAY
page 2). Use the REPEAT MODE ▲ and ▼ LCD buttons, the data dial, or the [+]/[–] buttons to select the
desired repeat mode: OFF, PHRASE, 1 SONG, or A-B REPEAT.
■ Phrase Repeat (Disk Orchestra Collection only) ...........
Use this function if you want to practice a specific phrase within a
song, as indicated by the phrase marks on the Disk Orchestra Collection
score.
When the PHRASE repeat mode is selected the PHRASE parameter
will appear on the display. Use the PHRASE ▲ and ▼ LCD buttons, or
the data dial or [+]/[–] buttons once the PHRASE parameter is selected,
to select the desired phrase number (refer to the Disk Orchestra Collection book that comes with the Disk Orchestra Collection disk). Playback
can be started and stopped as described above.
• The ALL or RANDOM playback mode
(SONG PLAY [MAIN] display) will be
disengaged when any of the repeat
modes is selected.
• Any previously set repeat mode will be
reset to OFF when a different song
number is selected.
■ 1 Song Repeat ......................................................................................................
When the 1 SONG mode is selected, any song selected and played as
described above will play repeatedly until stopped by pressing either the
STOP LCD button in the SONG PLAY [MAIN] display or the panel
[START/STOP] button.
69
Disk Orchestra Collection & Song Playback
○○○○○○○○○○○○○○○○○○○○○○○○○○
■ A-B Repeat ...............................................................................................................
This function allows you to specify any section of a song for continuous repeat playback.
When the A-B REPEAT mode is selected, A—> and B point entry buttons will appear on the display. While the song is playing, press the A—>
button once at the beginning of the section to be repeated and then press
the B button at the end of the section to be repeated. Repeat playback
will begin automatically from the A point as soon as the B point has been
specified. The programmed A and B points are retained until a different
song number or a different repeat mode is selected, and the A-B repeat
playback can be started and stopped again by using the [START/STOP]
button.
Other Playback Controls
■ Pause .............................................................................................................................
Press the [o PAUSE] button to temporarily stop song playback. Press
the [o PAUSE] button again (or the [START/STOP] button or START
LCD button in page 1) to resume playback from the same point.
SONG CONTROL
REW
FF
PAUSE
■ Rewind and fast Forward .........................................................................
During song playback the [r REW] and [f FF] buttons function
as follows:
SONG CONTROL
REW
70
FF
PAUSE
• The specified A-B repeat points will be
erased when a new song number or
another repeat mode is selected.
• A 1-measure count-in will normally be
produced when phrase or A-B repeat
playback is started. A count-in will not
be produced for songs that do not
contain a rhythm track.
• A count-in will not be produced in the 1
SONG repeat playback mode.
• When both the A and B points are
specified, pressing the B button clears
the B point only resulting in repeat
playback between the A point and the
end of the song. Pressing the A button
clears both the A and B points.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
Disk Orchestra Collection & Song Playback
● While playback is stopped or paused the [r REW] and [f FF]
buttons can be used to step backward or forward through the song a
measure at a time. Either button can also be held for continuous stepping in the specified direction.
● During playback the [r REW] and [f FF] buttons allow you to
move rapidly in the specified direction for as long as the button is
held. No sound is produced during [r REW] operation.
• The [ r REW], [ f FF], and [ o
PAUSE] buttons do not function when
playing with the guide function.
• Using the [r REW] button may cause
the voice, tempo, and/or volume to
change.
Playing Other Types of Music Data
In addition to original songs and Disk Orchestra Collection disks, the
Clavinova can also play back Yamaha Disklavier PianoSoft™ disks,
disks containing Yamaha ESEQ format sequence data, and disks containing songs recorded in Standard MIDI File format (SMF formats 0 and
1).
The Clavinova’s internal tone generator is compatible with the GM
System Level 1 voice allocation as well as the Yamaha DOC voice allocation.
• The [r REW] and [ f FF] buttons do
not function with SMF format 1 data.
• Yamaha ESEQ data recorded on other
Clavinovas (CVP- 55/65/75/83S/85A/
87A/89) will normally be played back
with the correct voices. It may be
necessary, however, to change the
voice numbers of the data to conform
to the CVP 79A/69/69A/59S voice
allocation when other types of data are
played back.
• Regardless of the type of software,
only the following disk formats can be
used: 3.5" 2DD 720 kilobyte format;
3.5" 2HD 1.44 megabyte format.
• The SONG PLAY [MAIN] (page 1),
[TRACK PLAY] (page 5), and MIXER
displays differ depending on the type
of data being played. The [PART ASSIGN] display (page 6) will not appear
when Disk Orchestra Collection or
Disklavier data is being played.
71
Song Recording
○○○○○○○○○○○○○○○○○○○○○○○○○○○
The CVP-79A/69/69A/59S features a built-in “sequencer” which can be used to
independently record up to 16 separate parts of a single musical composition.
Each part is recorded on a separate song “track”. The music data that you record
is stored on a 3.5" floppy disk loaded into the Clavinova’s disk drive unit. Up to
approximately 60 songs can be recorded on a single disk, depending on the
amount of data contained in each song. Before you can record, however, you
must “format” a new disk, as described on page 98.
A number of confirmation, information, prompt, alert, and error displays may appear during operation.
See the “MESSAGES” on page 110 if you need more details on any of these messages.
• The Clavinova records data using the SMF format 0 and the Clavinova’s internal voices which include GM
system level 1 compatible voice assignments.
SONG
PLAY
STYLE
VOLUME
MASTER
VOLUME
ABC/SONG
VOLUME
MAX
MAX
MIN
MIN
DEMO/HELP
16BEAT
DANCE
POP
LATIN
LATIN
POP
TRADITIONAL
INTRO A/
FILL TO A
INTRO B/
FILL TO B
MAIN A
POP
ROCK
SONG
CONTRAST
BALLAD
JAZZ
HARMONY
DISK
ONE TOUCH
SETTING
–
TEMPO
+
PLAY
RECORD
RECORD
GUIDE
VOICE
GUIDE
PIANO
E. PIANO
HARPSI.
VIBES
GUITAR
ORGAN
STRINGS/
CHOIR
BRASS
SAX/
FLUTE
BASS
MEMORY
BANK
1
CLAVI. TONE/
SYNTH
DUAL
EFFECT
BEAT
COUNTRY
WALTZ
METRONOME
PRESET
FUNCTION
MIXER
DRUMS/
PERC.
SPLIT
4
5
CUSTOM
REVERB
AUTO BASS CHORD
MAIN B
ENDING
SMALL
ABC
START/STOP
ABC ON
TAP
SYNCHRO
START/STOP
SONG CONTROL
PAGE
DISPLAY HOLD
EXIT
–
REGISTRATION
+
REW
FF
2
3
ABC FREEZE
PAUSE
SONG CONTROL
REW
FF
PAUSE
Quick Recording
Z Insert a Formatted Disk .............................................................................
If you haven’t already done so, make sure that a properly formatted
disk is loaded into the Clavinova disk drive (see page 98), and that the
disk’s write protect tab is set to the “write” position (tab closed).
• If you insert an unformatted disk, “Start
disk format?” will appear on the display. Press OK to format the disk or
CANCEL to abort.
• Protected disks (DOC, etc.) cannot be
formatted.
Write protect tab
closed (unlocked
— write enabled)
X Engage the Record Mode ........................................................................
Press the [RECORD] button so that its indicator lights and the
QUICK RECORD display appears. If the [RECORD] indicator is lit but
the QUICK RECORD display is not showing, use the PAGE buttons to
locate it (RECORD display page 1).
72
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Song Recording
SONG
PLAY
RECORD
GUIDE
C Select a Song Number ................................................................................
Use the SONG ▲ and ▼ buttons, the data dial, or the [+]/[–] buttons
to select a SONG NUMBER between 1 and 60 for the piece you are
about to record (up to 60 different songs, each with a different song
number, can be recorded on a single disk). Make sure the song number
you select has not already been used for a song previously recorded on
the disk you are using.
• If a song name appears along with the
song number, the selected song already contains data.
V Set the Track Modes as Required ...................................................
Two tracks (actually one track and a track group) are available for
quick recording: KBD (keyboard) and ABC&RHY (ABC & rhythm).
When the QUICK RECORD mode is first selected and a song that does
not already contain data is selected, the KBD (keyboard) track will be set
to REC and the ABC&RHY track will be set to OFF. In this state the
Clavinova is ready to record the keyboard track only. If you also want to
record rhythm and ABC accompaniment, use the ABC&RHY LCD button to set the ABC&RHY track to REC, or press the panel [ABC ON]
button.
If you select a song that already contains data, the track(s) which contains data can be set to PLAY. This lets you record a new track while
listening to previously-recorded material. If you don’t want to hear a
previously-recorded track while recording, simply use the corresponding
LCD button to turn it OFF.
• If ABC is already on when the record
mode is engaged, the ABC&RHY track
will automatically be set to “REC”.
• Harmony data can be recorded by
turning the HARMONY mode on. Also,
Dual or Split voices can be recorded
by engaging the Dual or Split mode. (In
this case the KBD part uses two
tracks.)
• When the ABC&RHY track is set to
“REC”, or when the KBD track is set to
“REC” and the ABC&RHY track is set
to “PLAY”, the metronome will sound
to provide a timing guide in the synchronized start mode before recording
is started
• When any track is set to “REC”, the
amount of disk space available for
recording will appear next to the tempo
display (in approximate kilobytes). An
empty 2DD/2HD disk should have
about 696KB/1407KB (room enough
for about 50,000/100,000 notes if no
other data is recorded) respectively.
When recording is started this display
is replaced by the measure number
display.
• REC mode cannot be selected if the
current song position is not the beginning of the song — e.g. the [r REW]
and [f FF] buttons have been used to
change the song position.
73
Song Recording
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
B Select a Voice ........................................................................................................
Use the VOICE selectors and displays to select the voice you want to
record with.
If you will be recording the ABC&RHY tracks you can also select a
style.
• If you want to try out the selected voice
on the keyboard before proceeding —
turn the synchro-start mode off so that
recording doesn’t start automatically as
soon as you play on the keyboard.
N Start Recording ...................................................................................................
Play on the keyboard. Recording will begin automatically as soon as
you start playing (the synchro start mode is automatically selected when
the QUICK RECORD mode is engaged — but it can be disengaged as
required). You can also start recording by pressing the panel [START/
STOP] button.
M Stop Recording ...................................................................................................
Stop recording by pressing the [START/STOP] button. When recording has finished and the recorded data has been written to disk, the mode
of the recorded track will automatically switch to PLAY, indicating that
the track is ready for playback.
• The Clavinova may continue to write
data to the disk for a short time after
you stop recording. DO NOT eject the
disk while the disk drive indicator is lit
or flashing.
• You can enter a name for the recorded
song, as described on page 87. (When
a song has been recorded, a temporary name “SONG_XXX.MID” (XXX is
the song number) will be given to the
song automatically.)
• During recording the [ABC/SONG]
volume control and the MIXER display
will function as the recorded ABC and/
or keyboard part volume control.
< Play Back the Recording ..........................................................................
Press the [START/STOP] button to play back your recording. Play
along on the keyboard if you like. During playback you can use the [o
PAUSE], [r REW], and [f FF] buttons, as described on page 70.
You can also change the playback tempo via the TEMPO [+] and [–]
buttons.
Playback will stop automatically when the end of the recording is
reached, or you can press the [START/STOP] button to stop it at
anytime.
Press the [RECORD] button so that its indicator goes out, or the
[EXIT] button, to exit from the QUICK RECORD mode.
74
• New data cannot be recorded to songs
recorded on other instruments, also
any edit in the record mode is not
possible.
• The guide lamps do not light during
recording.
• [ABC ON] and/or [HARMONY] button
indicator(s) automatically go out when
the recording of these parts has finished.
• When recording has finished, the
[EFFECT] is automatically turned off
(but the recorded effect remains active).
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Song Recording
Multi-track Recording & Playback
Z Insert a Formatted Disk, Engage the Record Mode &
Select a Song ........................................................................................................
The first three steps in the multi-track recording process are exactly
the same as those for quick recording: insert a formatted disk, press the
[RECORD] button to engage the record mode, and select a song number
— see steps 1, 2, and 3, above.
X Select the TRACK RECORD Page ..................................................
Use the PAGE buttons to select the TRACK RECORD page
(RECORD display page 2). The status of each track is shown above the
TRACK LCD buttons. Tracks which are enabled for playback are indicated by a box surrounding the track number, and tracks which are
record-enabled are indicated by a filled box and inverse number. Tracks
which do not contain data appear as dots.
C Set The Track Modes as Required .................................................
Use the TRACK < and > buttons to select a track (an underline cursor appears under the selected track). The data dial and [+]/[–] buttons
can also be used to select tracks. Use the REC/PLAY/OFF LCD button
to record-enable, play-enable, or turn off (mute) the selected track. Only
tracks which contain data can be play-enabled. The track number box
disappears when the track is muted.
75
Song Recording
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
In the normal single-voice play mode only one track needs to be
record-enabled at a time in order to record the keyboard part. If you intend to record using the DUAL or SPLIT mode, however, two tracks
must be record-enabled — only one or two tracks can be record-enabled
at a time to record the keyboard part. If ABC accompaniment is turned
on tracks 9 through 16 are automatically record-enabled (these are the
tracks on which the ABC data is recorded). If the HARMONY function
is engaged tracks 6 through 8 are automatically record-enabled (tracks 6
through 8 are used to record the harmony data).
The TRACK f LCD button can also be used to select the RHYTHM
tracks (9 and 10) if you only want to record the rhythm sound. The cursors appear under the 9 and 10 tracks, and the REC/PLAY/OFF LCD
button can be used to set them to record-enabled.
• Two tracks can be record-enabled only
when the DUAL or SPLIT mode is ON,
otherwise only one track can be
record-enabled.
• Track 10 (and 9 in some case) can
only be used to record the internal
rhythm sound and cannot be used to
record the keyboard part. Also, the
keyboard part should be recorded on a
track other than those used for ABC,
RHYTHM, and HARMONY.
• When the RHYTHM, ABC, and/or
HARMONY tracks are set to recordenabled, the synchronized start mode
is automatically turned on.
• When the RHYTHM tracks (9 and 10)
are set to record-enabled, or set to
play-enabled and other track(s) are set
to record-enabled, the metronome will
sound to provide a timing guide in the
synchronized start mode before recording is started.
V Set All Performance Features As Required .........................
After setting the tracks to be recorded to the record-enable mode, set
up all necessary performance features as required: voice, voice mode
(normal, dual, or split), style, tempo, etc.
B Start Recording ...................................................................................................
Unlike the QUICK RECORD mode the synchronized start mode is
automatically turned OFF when the multi-track recording mode is engaged. You can, however, engage the synchro start mode at this point so
that recording will begin automatically as soon as any key on the keyboard is pressed. Otherwise press the [START/STOP] button to start
recording on the specified track(s). The current measure number is
shown on the display as you record.
The following parameters will be recorded in addition to notes you
play:
76
• If ABC and/or HARMONY is already on
when the multi-track recording mode is
engaged, the corresponding tracks are
automatically record-enabled and the
synchronized start mode is automatically turned ON.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Song Recording
Parameters recorded for Each Track
Parameters Recorded for the Entire Song
•
•
•
•
•
•
•
•
•
Notes
Voice
Volume (initially maximum)
Expression (CVP-79A only)
Pan
•
•
•
•
•
Damper pedal
Soft pedal
Sostenuto pedal
Reverb depth
Effect depth
Tempo
Reverb type
Reverb depth
Effect type*
•
•
•
•
•
Style
Main A/B
Intro
Fill-in
Ending
* The last recorded track effect takes priority.
Other Recorded Parameters
• Accompaniment data is distributed to the appropriate
tracks. Accompaniment data which is recorded but
not listed above includes:
* Individual part volume
* Modulation
* Pitch bend
* Pitch bend sensitivity
• Harmony data is distributed to the appropriate
tracks.
• DUAL mode voices are recorded on the two assigned tracks.
• SPLIT mode voices are recorded on the two assigned tracks.
N Stop Recording ...................................................................................................
Press the [START/STOP] button to stop recording.
• If you have recorded using a preset
style on RHYTHM tracks 9 and 10, a
box symbol will appear next to the
“RHYTHM” character in the display.
Adding New Tracks
Recorded tracks are automatically switched to the play mode when
recording is stopped, so you can play back the recorded data simply by
pressing the [START/STOP] button, or add a new track to your song by
selecting a new record track(s) and voice(s) and recording as described
above.
• If you record on a track that has already been recorded, the previous
material will be erased and the new
material will be recorded in its place.
Press the [RECORD] button so that its indicator goes out, or the
[EXIT] button, to exit from the multi-track recording mode.
77
Song Recording
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Punch-in/out Recording
“Punch-in/out recording” allows you to start recording from any “punch-in” point within a previouslyrecorded track and stop recording at any “punch -out” point, leaving all recorded material up to the punchin point and following the punch-out point intact. The punch-in recording controls are accessed via the
RECORD [PUNCH IN/OUT] display (RECORD display page 3).
Z Play the Song ........................................................................................................
Play back the song in order to locate the point you want to punch-in
from.
START/STOP
TAP
SYNCHRO
START/STOP
• The Punch-in/out recording function
cannot be used when no disk is in the
drive.
• [ f FF] or [r REW] buttons cannot
be used while in the [PUNCH IN/OUT]
display.
X Pause Before the Punch-in Point ....................................................
Press the [o PAUSE] button to pause playback a bit before the point
at which you want to start recording. Leave a measure or more before the
punch-in point so you’ll be able to grasp the timing for the punch in.
SONG CONTROL
REW
FF
PAUSE
C Select a Track .......................................................................................................
Use the TRACK ▲ and ▼ LCD buttons or the data dial or [+]/[–]
buttons to the select the track to be recorded on. The voice used in the
selected track will be shown on the display.
78
• Only tracks which allow punch-in/out
recording will appear and can be selected. The RHYTHM, ABC, HARMONY, and unrecorded tracks cannot
be selected.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Song Recording
V Select a Punch-in Mode .............................................................................
Use the MODE LCD button to select the 1ST KEY or PEDAL punchin mode.
1ST KEY
Recording will begin with the first key played after the PUNCH
IN LCD button is pressed.
PEDAL
Recording will begin when the left pedal is pressed after the
PUNCH IN LCD button is pressed.
• When the PEDAL punch-in mode is
selected, the left pedal is used for this
function only (the usual pedal function
is canceled).
B Engage the Punch-in Record Ready Mode ..........................
Press the PUNCH IN LCD button to engage the punch-in record
ready mode — the PUNCH IN button will be highlighted.
N Start Playback & Recording ..................................................................
Press the [START/STOP] or [o PAUSE] button to start playback
from the current pause location, then, if the 1ST KEY mode is selected,
begin playing at the point you want to record from. Recording will begin
as soon as you begin playing on the keyboard. If the PEDAL mode is
selected press the left pedal at the point you want to record from.
When the PEDAL punch-in mode is
selected:
• Recording can be started directly by
pressing the left pedal while playback
is paused (without first pressing the
[START/STOP] or [PAUSE] button).
• Recording can also be stopped by
pressing the left pedal. In this case the
data following the punch-out point will
be left active.
• If you start recording by pressing the
left pedal while playback is paused,
and stop by the [START/STOP] button,
the result will be that all the data after
the punch-in point will be erased. (If
you stop by using the PUNCH OUT
LCD button or the left pedal, only the
data between the punch-in and punchout points will be erased.)
M Stop Recording ...................................................................................................
Press the PUNCH OUT LCD button to stop recording at the point at
which you want to “punch out”, leaving all data following the punch-out
point intact. Use the panel [START/STOP] button to stop recording if
you want all data following the punch-out point to be erased.
Press the [RECORD] button so that its indicator goes out, or the
[EXIT] button, to exit from the punch-in/out record mode.
• If you press the [START/STOP] button
or [o PAUSE] button to start recording,
and the [START/STOP] button or the
PUNCH OUT LCD button to stop
recording without actually recording
anything in between, the original data
will be left untouched.
79
Song Recording
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Chord Sequence Function
The CHORD SEQUENCE function provides a convenient way to enter chord sequences and style
changes one at a time.
Z Engage the Chord Sequence Function ....................................
After engaging the QUICK RECORD mode (RECORD display page
1) and selecting a song number, press the CHORD SEQ. LCD button.
The CHORD SEQUENCE display will appear, ABC will be turned on,
and if the FULL KEYBOARD mode is currently selected the FINGERED CHORD mode will be selected instead.
• The chord Sequence function cannot
be used when no disk is in the disk
drive.
• The chord sequence data will replace
any previous data on the ABC and
rhythm tracks that was recorded in the
quick record or multi-track record
modes.
• Up to 999 measures can be recorded
using the Chord Sequence function.
• The chord input resolution will be
automatically selected according to the
current style. For 3/4, 4/4, and 5/4 time
styles, one chord can be entered on
every 8th note or 8th-note triplet. For
other time signatures one chord can be
entered for each measure.
X Move the Cursor To the Entry Point ..............................................
As necessary, use the CURSOR < and > LCD buttons to move the
triangular cursor to the point at which you want to enter a chord or style
change.
• One style change or section change
(except Fill-in and Break) can be made
at the beginning of each measure. —
The “Button not valid! Enter at top of
measure.” alert display will appear if
you attempt to enter the change in any
other place than the top of measure.
• ABC cannot be turned off after the
chord sequence function is engaged.
But the ABC mode can be altered
between FINGERED and SINGLEFINGER in the pop-up display by
pressing the [ABC ON] button. The
split point can also be altered.
• If you enter the ABC part volume data
via the MIXER display and the SET
LCD button, the volume event symbol
will appear in the box on the right side
of the LCD display. (The volume event
is automatically entered at the beginning of a song.)
C Enter and Set the Chords and/or Style Changes ...........
To enter a chord either play the chord on the ABC section of the keyboard according to the current ABC mode, or use the ROOT and TYPE
LCD buttons. The data dial or [+]/[–] buttons can be used to select the
ROOT or TYPE once the corresponding parameter has been selected by
pressing its LCD button. When a chord is entered via the keyboard the
appropriate root and type appear in the corresponding parameter locations. To enter a style change (style, section, and tempo) simply make the
80
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
appropriate selections in the normal way. Once the chord and/or style
change has been entered, press the SET LCD button to actually input
the chord and/or style change at the current cursor location. The location in the graphic measure symbol will become bold and the set data
will be shown on the display: the time signature, the style name and
section to the left, and the chord, tempo, and rhythm on/off status (see
below) in the box to the right.
Continue entering chords and style changes in this manner until
your sequence is complete. The data recorded by the Chord Sequence
function is listed below.
Data Recorded By the Chord Sequence Function
•
•
•
•
•
•
•
Style
Accompaniment Section (MAIN A & B/Intro/Ending/Fill-in/Break)
Chord
ABC part volume (MIXER settings)
Tempo
Rhythm on/off
ABC/SONG volume (as an initial setting only)
V Stop Recording .............................................................................................
When all the required chords and style changes have been entered,
enter an END MARK (press END MARK in display page 2), then
press the END button in display page 3. The “Are You Sure?”
confirmation prompt will appear. Press YES to save the recorded data
and finish recording or NO to abort. Once the data has been saved, the
Chord Sequence function will automatically be exited.
It is also possible to leave the Chord Sequence function during
recording by pressing the [EXIT] button, or the [RECORD] button
so that its indicator goes out. In this case, if any data is left unsaved,
the “Save recorded data?” confirmation prompt will appear.
Press YES to save the recorded data and then exit from the Chord
Sequence function, NO to exit without saving the data, or CANCEL
to return to the Chord Sequence function.
Song Recording
• The types of chords that can be entered are
the same as those listed for the ABC fingered mode (see page 36). In addition “- - -”
(i.e. no chord) can be entered via the TYPE
LCD button.
On-bass chords can be entered via the
keyboard.
• The number of each measure is shown to
the left of the graphic measure symbols on
the display.
• See “Chord Sequence Page-2 Functions”,
below, for other useful editing features.
• If no chords are entered (i.e. chord type is
set to “- - -”), the result will be a rhythm-only
sequence.
• A “Break” can be produced by both setting
the chord type to “- - -” and rhythm sound to
“OFF” (see “Rhythm OFF/ON”, below).
• The same chord, as set previously (i.e. the
same chord shown in the box), cannot be
entered even if the SET LCD button is
pressed.
• Only data other than chord data can be
entered by first moving the cursor and
making the required changes without entering any chord (the ROOT and TYPE LCD
sections should be blank), and pressing the
SET LCD button.
• If a different style with another time signature is selected after chords have been
entered, the timing of the chords will be
changed accordingly.
• The chord sequence data now resides in
tracks 9 through 16, and can be played
back in the normal way. Add other tracks as
required by using the standard track selection and recording procedure. You can also
record over individual tracks of the sequence and replace them with original
material if you like by using the standard
track selection and record procedure.
• The song recorded via the Chord Sequence
function can be modified later by re-entering the Chord Sequence mode and making
the required changes. But please note that
the track data recorded over by using the
standard recording procedure will be returned back to the preset style data.
Chord Sequence Page 2 & 3 Functions
The CHORD SEQUENCE page-2 and page-3 displays contain a number of functions that can make the
chord-entering process more efficient and versatile.
81
Song Recording
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
● Delete
Press the DELETE LCD button to delete the data at the current cursor
location. The “Are you sure?” confirmation prompt will appear.
Press YES to delete or CANCEL to abort.
● End Mark
Press the END MARK LCD button to enter an “end mark” at the current cursor location. An END MARK signifies the end of the song,
and should always be entered to properly end each song. The cursor
can not be moved past an end mark. An end mark can be deleted using the DELETE LCD button, above.
● Rhythm OFF/ON
Pressing the RHYTHM OFF LCD button turns the rhythm sound off
— i.e. the start of a rhythm break — from the current cursor location.
This button has no effect if the rhythm is already off.
The RHYTHM ON LCD button turns the rhythm back on after a
rhythm break. This button has no effect if the rhythm is already on.
● All Delete
When the ALL DELETE LCD button is pressed the “Are you
sure?” confirmation display will appear. Press YES to erase all
chord and style change data, or NO to abort.
● Check Play
The CHECK PLAY LCD button starts playback of the programmed
chord sequence. The sequence will play through until the end of the
data is reached or until the CHECK PLAY LCD button is pressed a
second time.
● End
Pressing the END LCD button initiates final processing of the sequence data and saves it to the disk. The “Are you sure?” confirmation prompt will appear: press YES to save it to disk and finish
recording the chord sequence or NO to abort. Once the data has been
processed and saved to disk the Chord Sequence mode is automatically exited.
82
• Unless the end mark is entered, the
song will end at one measure after the
last data, or at the end of the ending
section if it is entered.
• The end mark symbol will appear in
the box on the right side of the LCD
display when it is entered.
• The rhythm on/off status is shown in
the box to the right on the LCD display.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Song Recording
Other Song Recording Functions
• Track Mix, Track Delete, Track Quantize, Initial Edit, and Rename functions,
described below, cannot be used when no disk is in the disk drive.
Track Mix
The TRACK MIX function combines the data from two specified tracks and places the result in a third
specified track. The TRACK MIX function is accessed via the RECORD [TRACK MIX] display
(RECORD display page 4).
Z Specify the Tracks to be Mixed ..........................................................
Use the TRK A and TRK B LCD buttons — or the data dial or [+]/[–]
buttons once the TRK A or TRK B parameter has been selected — to
specify the tracks you want to mix. The initial voices used for the A and
B tracks are shown along with the track number.
• Only the data-containing tracks will
appear and can be selected for TRK A
and B. In addition “no track” (“- -”) can
also be selected for TRK B. — In this
case the result will be the copy of TRK
A to TRK C.
• The initial data and all data other than
note data is taken from that of track A.
X Specify the Destination Track .............................................................
Use the TRK C LCD button — or the data dial or [+]/[–] buttons once
the TRK C parameter has been selected — to specify the track you want
the mixed data to be placed in. Any previous data in the destination track
(TRK C) will be erased.
C Execute the Track Mix Operation ....................................................
Press the MIX LCD button to begin execution of the track mix operation. The “Are you sure?” confirmation prompt will appear. Press
YES to mix the specified tracks or NO to cancel the operation.
When this is done the MIX LCD button will change to UNDO, allowing you to undo the track mix operation and return to the pre-mixed
data before selecting a different track or exiting from the Track Mix
mode.
Press the [EXIT] button, or the [RECORD] button so that its indicator goes out to exit from the Track Mix function.
• A bar graph indicating the progress of
the track mix operation will appear
while the data is being processed.
• You can check if the results are as you
expected or not, by starting and stopping playback by using the [START/
STOP] button before the UNDO operation.
83
Song Recording
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Track Delete
The TRACK DELETE function accessed via the RECORD [TRACK DELETE] display (RECORD
display page 5) can be used to delete all data from any specified track.
Z Specify the Track to be Deleted ........................................................
Use the TRACK ▲ and ▼ buttons, the data dial, or the [+]/[–] buttons
to specify the track you want to delete.
• Only the data-containing tracks will
appear and can be selected.
X Execute the Delete Operation .............................................................
Press the DELETE LCD button to begin execution of the track delete
operation. The “Are you sure?” confirmation prompt will appear.
Press YES to delete the specified track or NO to cancel the operation.
After processing the DELETE LCD button changes to UNDO, which can
be used to undo the delete operation before selecting a different track or
exiting from the Track Delete mode.
Press the [EXIT] button, or the [RECORD] button so that its indicator goes out to exit from the Track Delete function.
• A bar graph indicating the progress of
the track delete operation will appear
while the data is being processed.
• You can check if the results are as you
expected or not, by starting and stopping playback by using the [START/
STOP] button before the UNDO operation.
Track Quantize
You can “tighten up” the timing of a recorded part by aligning all notes to specified beats via the
TRACK QUANTIZE function accessed via the RECORD [TRACK QUANTIZE] display (RECORD display page 6).
Z Specify the Track to be Quantized .................................................
Use the TRACK ▲ and ▼ buttons, the data dial, or the [+]/[–] buttons
to specify the track you want to quantize.
84
• Only the data-containing tracks will
appear and can be selected.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Song Recording
X Specify the “Quantize Size” ..................................................................
Use the LCD button below the note symbol to select “quantize size”
— i.e. the beats to which the notes in the selected track will be aligned:
32nd notes
3
16th note triplets
16th notes
3
8th note triplets
8th notes
3
quarter-note triplets
quarter notes
C Execute the Quantize Operation ......................................................
Once the required quantize size has been selected press the
QUANTIZE LCD button to quantize the selected track. The “Are you
sure?” confirmation prompt will appear. Press YES to quantize the
data or NO to abort. When this is done the QUANTIZE LCD button will
change to UNDO, allowing you to undo the quantize operation and return
to the pre-quantized data before selecting a different track or exiting
from the Track Quantize mode.
Press the [EXIT] button, or the [RECORD] button so that its indicator goes out to exit from the Track Quantize function.
• Only note and voice data is quantized.
• A bar graph indicating the progress of
the quantize operation will appear
while the data is being processed.
• You can check if the results are as you
expected or not, by starting and stopping playback by using the [START/
STOP] button before the UNDO operation.
Initial Edit
The values of the initial data can be changed for each track or the entire song by using the INITIAL
EDIT parameters accessible via the RECORD [INITIAL EDIT] display (RECORD display page 8).
Z Select a Song & Engage the Edit Mode ....................................
Use the SONG ▲ and ▼ buttons, the data dial, or the [+]/[–] buttons
to specify the song you want to edit, then press the EDIT LCD button to
go to the INITIAL EDIT pages.
85
Song Recording
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
X Edit the Parameters .......................................................................................
Three INITIAL EDIT display pages are available. Use the PAGE [<]
and [>] buttons to select the various pages and edit the parameters each
contains. It is possible to start and stop playback by using the [START/
STOP] button while editing the parameters in order to hear how the
changes affect the sound.
● Page 1: INITIAL EDIT [SONG]
This page contains the REVERB TYPE and DEPTH parameters, the
TEMPO parameter, and the WRITE LCD button which is used to
actually write all initial data changes once they have been made as
required. The REVERB TYPE and DEPTH parameters and the
TEMPO parameter affect the entire song and are edited by using the
corresponding LCD buttons to select each parameter, and then the
data dial or the [+]/[–] buttons to edit (see page 22 for information on
the reverb types and depth settings, and page 29 for tempo information).
● Page 2: INITIAL EDIT [TRACK]
Page 2 includes VOICE, VOLUME, and PAN parameters that can be
set individually for each track. The VOICE parameter sets the initial
voice for the track; the VOLUME parameter sets the initial volume of
the track, and the PAN parameter sets the initial pan position of the
track. Use the TRACK ▲ and ▼ buttons — or the data dial or the [+]/
[–] buttons once the TRACK parameter has been selected — to
specify the track you want to edit, then set the parameters in this and
the following page as required.
● Page 3: INITIAL EDIT [TRACK]
Page 3 contains EFFECT TYPE and DEPTH parameters and a REVERB DEPTH parameter that can be set individually for each track.
The track to be edited is selected in page 2 (see above), and the parameters can be edited as required. See page 24 for information on the
available effect types and depth settings.
86
• The data may not be played back
accurately if you use the [r REW]
and [f FF} buttons while editing the
initial data.
• In the Initial Edit mode the panel
buttons relating to the editable parameters cannot be used.
• Only the data-containing tracks will
appear and can be selected.
• The VOLUME parameter’s initial
default value is “100” for every track.
This value can only be decreased.
• The effect type and depth may not be
able to be set as expected in some
cases. The other tracks are also
affected and the last set track effect
type takes priority.
• The VOICE and EFFECT TYPE
parameters cannot be edited for the
non-keyboard tracks (i.e. the
RHYTHM, ABC, and/or HARMONY
tracks).
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Song Recording
C Write the Changes ...........................................................................................
When all the initial data changes have been made as required, go back
to INITIAL EDIT page 1 and press the WRITE LCD button. The “Are
you sure?” confirmation display will appear. Press YES to actually
make the specified changes, or NO to abort. When this is done the
WRITE LCD button will change to UNDO, allowing you to undo the
write operation and return to the pre-edited data before making any other
edits or exiting from the Initial Edit mode.
• All edited data for any number of
tracks within one song can be written
in a one-time WRITE operation.
• You can check if the results are as you
expected or not, by starting and stopping playback by using the [START/
STOP] button before the UNDO operation.
V Exit ....................................................................................................................................
Press the [EXIT] button, or the [RECORD] button so that its indicator goes out to exit from the Initial Edit mode. If you do this after making
any edits that you have not yet written, the “Write edited data?”
confirmation prompt will appear. Press YES to write the edited data and
then exit from the Initial Edit mode, NO to exit without writing the data,
or CANCEL to return to the Initial Edit mode.
Renaming Song Files
This function lets you enter an original name for, or change the existing name of, any song file on the
disk recorded by the CVP-79A/69/69A/59S. The rename function is accessed via the RECORD [RENAME] display (RECORD display page 7).
Z Select a Song & Engage the Rename Mode ........................
Use the SONG ▲ and ▼ buttons, the data dial, or the [+]/[–] buttons
to specify the song you want to rename, then press the RENAME LCD
button to go to the NAMING display.
87
Song Recording
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
X Enter a Name .........................................................................................................
The current song file name appears in the upper right corner of the
display. Use the > LCD button to position the underline cursor at the
character you want to change (song names can be up to 12 characters in
length). Use the data dial or [+]/[–] buttons to select the character you
want to enter from the list in the center of the display, then press the
c.set LCD button to enter the character at the current cursor position.
Repeat this procedure until your name is complete. The c.del LCD button can be used to back up one space and delete a character.
C Register the Name ...........................................................................................
When the name is complete press the OK LCD button to register the
name for the current song file, or CANCEL to abort.
Press the [EXIT] button, or the [RECORD] button so that its indicator goes out, to exit from the Rename mode.
88
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Song Recording
Recording Without a Disk
The Clavinova has enough internal RAM memory (about 25KB) to
allow recording for a while even if a disk is not loaded (up to approximately 2,500 notes if no other data is recorded).
• Chord sequence data is not recorded
to internal RAM memory. — The “Button not valid !” alert display will appear.
• The Punch-in/out Recording, Track
Mix, Track Delete, Track Quantize,
Initial Edit, and Rename functions (i.e.
RECORD display page 3 to the last
page) cannot be used with data in the
internal RAM memory. — The “Button
not valid !” alert display will appear.
QUICK RECORD display when recording to internal RAM memory
SONG PLAY [MAIN] display when playing back internal RAM
memory song
If you accidentally record without loading a disk, make sure you use
the SONG COPY function (described on page 102) to copy the recorded
data to disk if you want to keep the recorded data (the internal RAM
memory is not backed up). This is necessary because the internal RAM
memory is cleared automatically when a Disk Orchestra Collection,
Disklavier PianoSoft, Style File disk, or a disk containing songs recorded
on a different instrument is loaded. The RAM is also cleared when an
original song disk is loaded and a song is selected.
Playback
Original recordings can be played back and controlled in the same
way as described in the “Disk Orchestra Collection & Song Playback”
section, beginning on page 61. You can individually select tracks to play
back (page 63), use the guide modes and keyboard guide lamps with the
data recorded on any two tracks (page 67), and use the A-B repeat function (page 70).
89
The Utility Functions
○○○○○○○○○○○○○○○○○○○○○○
The “utility functions” described in this chapter include keyboard,
disk, MIDI, and general functions that significantly enhance the
versatility and flexibility of the CVP-79A/69/69A/59S. All of the utility
functions are selected and set in the same way for consistent, easy
operation:
Z Press the [FUNCTION] button so that its indicator lights.
FUNCTION
MIXER
X Use the PAGE [<] and [>] buttons to select the page containing the
desired function.
PAGE
DISPLAY HOLD
C Use the LCD buttons, data dial, and/or [+]/[–] buttons to select and
set the individual parameters as required.
• The data dial and the [+]/[–] buttons
can be used for the parameters once
selected by the LCD button in the
highlighted round-framed parameter
box.
–
+
V Press the [EXIT] button, or the [FUNCTION] button so that its indicator goes out when done.
EXIT
90
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Utility Functions
Keyboard
■ Transpose .........................................................................................................
The Transpose function makes it possible to shift the pitch of the
entire keyboard up or down in semitone intervals up to a maximum
of two octaves (from –24 through 0 to +24). “Transposing” the pitch
of the Clavinova keyboard makes it easier to play in difficult key
signatures, and you can simply match the pitch of the keyboard to
the range of a singer or other instrumentalist.
Use the data dial or [+]/[–] buttons to set the desired degree of
transposition.
• The transpose function does not affect the
Drum Kit voices.
■ Octave Shift ......................................................................................................
• Notes below and above the original 88-key
range of the Clavinova sound one octave
higher and lower, respectively.
This function includes three parameters which determine whether
the left-hand voice in a split keyboard setup (LEFT), the 2nd voice
in the dual mode (2ND), and the right-hand or main voice (RIGHT/
1) will be shifted up or down one octave.
Press the LEFT, 2ND, or RIGHT/1 LCD button as many times
as necessary to set as required:
–1
0
+1
Corresponding voice shifted down one octave.
No shift. (Default for the RIGHT/1 and 2nd voices.)
• Press the [–] and [+] buttons simultaneously
to restore normal keyboard pitch (“0”).
• The Transpose setting is retained in memory
even when the power is turned off if the
BACKUP page VOICE SETTING parameter
is turned on (page 107), otherwise the
Transpose is always set to “0” when the
power is turned on.
• The Octave Shift setting is retained in
memory even when the power is turned off if
the BACKUP page VOICE SETTING parameter is turned on (page 107).
• Notes below and above the original 88-key
range of the Clavinova sound one octave
higher and lower, respectively.
• In the normal play mode (i.e. single voice
mode) only the RIGHT/1 setting is effective.
Corresponding voice shifted up one octave. (Default for the
LEFT voice.)
■ Touch Sensitivity ......................................................................................
The Clavinova can be set to one of five different types of keyboard touch sensitivity to match different playing styles and preferences. Press the KEY TOUCH button as many times as necessary to
select the desired touch response setting.
SOFT 2
Allows maximum loudness to be produced with very light
key pressure.
SOFT 1
Not as sensitive as the “SOFT 2” setting, but maximum
loudness can still be easily produced with relatively light
key pressure.
NORMAL
Produces a fairly “standard” keyboard response. (Default.)
HARD 1
Requires the keys to be played quite hard to produce
maximum loudness.
HARD 2
Requires the keys to be played very hard to produce maximum loudness.
• The Touch Sensitivity setting is retained in
memory even when the power is turned off if
the BACKUP page VOICE SETTING parameter is turned on (page 107), otherwise the
NORMAL setting is automatically selected
whenever the POWER switch is turned on.
91
The Utility Functions
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Sound
■ Tune .........................................................................................................................
The Tune function makes it possible to tune the Clavinova over
about a ±26-Hertz (±100-cent) range in 0.2-Hertz intervals. A hundred “cents” equals one semitone, so the tuning range provided allows
fine tuning of overall pitch over a range of approximately a semitone.
This function is useful for tuning the Clavinova to match other instruments or recorded music. Normal pitch is A3 = 440 Hertz.
Use the TUNE ▲ and ▼ LCD buttons to set the tuning as required. The data dial and [+]/[–] buttons can also be used once the
TUNE parameter has been selected. The default value of 440.0Hz
can be instantly recalled by pressing the TUNE ▲ and ▼ LCD buttons simultaneously.
■ Pan ............................................................................................................................
The pan positions of the left-hand voice in a split keyboard setup
(LEFT), the 2nd voice in the dual mode (2ND), and the right-hand
or main voice (RIGHT/1) can be individually set via the appropriate
PAN parameters.
Press the LEFT, 2ND, or RIGHT/1 LCD button according to the
voice you want to pan, then use the data dial or [+]/[–] buttons to set
the pan position as required. The graphic bar shows the approximate
pan position between full left (“L”) and full right (“R”). The default
position can be instantly recalled by pressing the [+] and [–] buttons
simultaneously.
Pedal
CVP-79A
92
CVP-69/69A/59S
• The Tune setting is retained in memory even
when the power is turned off if the BACKUP
page TUNE/MICRO TUNING parameter is
turned on (page 107), otherwise the tuning is
always set at 440.0Hz when the power is
turned on.
• The Tune function does not affect the Drum
Kit voices.
• The pan setting is retained in memory even
when the power is turned off if the BACKUP
page VOICE SETTING parameter is turned
on (page 107).
• The default pan position for some voices is
center, while some voices feature keyboard
scaling — i.e. the keyboard is spread across
the stereo sound field (see the voice list on
page 116). Both types appear in center
position on the LCD. Any changes in the pan
setting are then relative to the default position.
• The Drum Kit voices have special pan settings for each individual instrument.
• The PAN setting affects all voices.
• The PAN setting affects the keyboard sound
only.
• In the normal play mode (i.e. single voice
mode) only the RIGHT/1 setting is effective.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Utility Functions
■ Left Pedal Function ........................................................................................
The left pedal has a number of functions which can be selected via
the LEFT PEDAL function. Use the LEFT PEDAL ▲ and ▼ LCD buttons to select the desired function. The data dial and [+]/[–] buttons can
also be used. The default setting — “SOFT” — can be instantly recalled
by pressing the LEFT PEDAL ▲ and ▼ LCD buttons simultaneously.
Soft
Pressing the soft pedal subtly reduces the volume and
slightly changes the timbre of notes played. The SOFT
function is automatically selected when the POWER
switch is initially turned on.
Start/Stop
The left pedal performs the same function as the accompaniment section [START/STOP] button. For details on
the START/STOP function, refer to the “Accompaniment” section, pages 30, 32.
Harmony On/Off
Allows the Harmony function (page 41) to be turned on
or off as required while playing so that harmony can be
applied only to specific notes or phrases.
Registration +
Steps through the registration memory locations so a
completely different set of panel settings can be recalled
each time the pedal is pressed. See page 60 for details
on the registration memory.
Intro A/Fill to A
The left pedal performs the same function as the accompaniment section [INTRO A/FILL TO A] button. See
pages 30, 32 for details.
Intro B/Fill to B
The left pedal performs the same function as the accompaniment section [INTRO B/FILL TO B] button. See
pages 30, 32 for details.
Ending/rit.
The left pedal performs the same function as the accompaniment section [ENDING] button. See page 32 for
details.
Break
Pressing the left pedal produces a break in the accompaniment for as long as the pedal is held. For details on
the BREAK function, refer to the “Accompaniment” section, page 32.
Sostenuto
(CVP-59S only)
The left pedal functions in the same way as the CVP79A/69/69A sostenuto pedal (see page 26).
• The Left Pedal function setting is retained in memory even when the
power is turned off if the BACKUP
page PEDAL parameter is turned on
(page 107).
• If the left pedal is assigned to the
“Registration +” function, the setting of
the left pedal function in the registration memory is not recalled.
■ Damper Range .....................................................................................................
Determines whether the damper pedal affects the right-hand, lefthand, or both voices in a split setup.
Press the DAMPER RANGE LCD button as many times as necessary
to select the desired setting.
R
The damper affects only the right-hand voice. (Default.)
L
The damper affects on the left-hand voice.
L&R
The damper affects both the left-hand and right-hand voices.
• The Damper Range setting is retained
in memory even when the power is
turned off if the BACKUP page PEDAL
parameter is turned on (page 107).
93
The Utility Functions
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
■ Damper Mode (CVP-79A only) ............................................................
Sets the damper pedal for on/off or continuous operation (refer to
page 26). Press the DAMPER MODE LCD button to alternately select
the continuous and switch modes.
CONT.
Continuous damper pedal operation. (Default.)
SWITCH
On/off damper pedal operation.
• The Damper Mode setting is retained
in memory even when the power is
turned off if the BACKUP page PEDAL
parameter is turned on (page 107).
MIDI 1
MIDI, the Musical Instrument Digital Interface, is a world-standard communication interface that allows MIDI-compatible musical instruments and equipment to share musical information and control one
another. This makes it possible to create “systems” of MIDI instruments and equipment that offer far
greater versatility and control than is available with isolated instruments. The MIDI parameters included in
the CVP-79A/69/69A/59S’s three MIDI function pages provide extensive flexibility in adapting the
Clavinova to just about any MIDI system.
The parameters contained in the MIDI 1 function page include the SEND CH, which determines the
BASIC and LEFT/2 voice MIDI send channels, LOCAL control setting — on or off, and the CLOCK setting — internal or external.
■ Send Channel .......................................................................................................
In any MIDI control setup, the MIDI channels of the transmitting and
receiving equipment must be matched for proper data transfer (there are
16 MIDI channels). This function sets the basic and left-hand/2nd MIDI
send (transmit) channels of the CVP-79A/69/69A/59S. The LEFT/2
parameter applies to the left-hand voice in split keyboard setups and to
the 2nd voice in the dual mode. All other keyboard data is transmitted via
the BASIC channel. Both parameters can be turned OFF or set to any
channel from 1 through 16.
Press the BASIC or LEFT/2 LCD button according to the channel
you want to set, then use the data dial or [+]/[–] buttons to set the channel as required.
● MIDI Reception
The CVP-79A/69/69A/59S always receives MIDI data in the “MultiTimbre” mode. This is a mode in which the Clavinova voices can be
independently controlled on different MIDI channel numbers (1
through 16) by an external MIDI device.
94
• The Send Channel settings are retained in memory even when the
power is turned off if the BACKUP
page MIDI parameter is turned on
(page 107), otherwise the default
BASIC send channel is 1 and the
default LEFT/2 send channel is OFF.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Utility Functions
■ Local Control ON/OFF .................................................................................
“Local Control” refers to the fact that, normally, the Clavinova keyboard controls its internal tone generator, allowing the internal voices to
be played directly from the keyboard. This situation is “Local Control
ON” since the internal tone generator is controlled locally by its own
keyboard.
Local control can be turned off, however, so that the Clavinova keyboard does not play the internal voices, but the appropriate MIDI information is still transmitted via the MIDI OUT connector when notes are
played on the keyboard. At the same time, the internal tone generator
responds to MIDI information received via the MIDI IN connector. This
means that while an external MIDI sequencer, for example, plays the
Clavinova’s internal voices, an external tone generator can be played
from the Clavinova keyboard.
Press the LOCAL LCD button to alternately turn local control ON and
OFF.
• The Local setting is retained in
memory even when the power is
turned off if the BACKUP page MIDI
parameter is turned ON (page 107),
otherwise the default setting is ON.
■ Clock ..............................................................................................................................
This function determines whether the Clavinova’s auto-accompaniment or song record/playback timing is controlled by the Clavinova’s
own internal clock or an external MIDI clock signal received from external equipment connected to the MIDI IN connector.
Press the CLOCK LCD button to alternately select the EXT. (external) or INT. (internal) clock mode.
• The Clock setting is retained in
memory even when the power is
turned off if the BACKUP page MIDI
parameter is turned ON (page 107),
otherwise the default setting is INT.
• If the Clock Mode is set to EXT. and a
MIDI clock signal is not being received
from an external source, the rhythm,
ABC and other clock-dependent features will not operate.
MIDI 2
The “MIDI 2” function page contains the MIDI FILTER settings which can be used to turn transmission
and reception of certain types of MIDI data on or off.
95
The Utility Functions
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
■ Program ......................................................................................................................
Normally the Clavinova will respond to MIDI program change numbers received from an external keyboard or other MIDI device, causing
the correspondingly numbered Multi-Timbre mode voice to be selected
on the corresponding channel (the keyboard voice does not change). The
Clavinova will normally also send a MIDI program change number
whenever one of its voices is selected, causing the correspondingly numbered voice or program to be selected on the external MIDI device if the
device is set up to receive and respond to MIDI program change numbers.
This function makes it possible to cancel program change number
reception and transmission so that voices can be selected on the
Clavinova without affecting the external MIDI device, and vice versa.
Press the PROGRAM LCD button to alternately turn program change
number reception and transmission ON (SEND&RECEIVE) and OFF.
• The Program setting is retained in
memory even when the power is
turned off if the BACKUP page MIDI
parameter is turned ON (page 107),
otherwise the default setting is
SEND&RECEIVE.
■ Control ..........................................................................................................................
Normally the Clavinova will respond to MIDI control change data
received from an external MIDI device or keyboard, causing the corresponding Multi-Timbre mode voice to be affected by pedal and other
“control” settings received from the controlling device (the keyboard
voice is not affected). The Clavinova also transmits MIDI control change
information when either of its pedals are operated.
This function makes it possible to cancel control change data reception and transmission if you do not want the Clavinova to be affected by
control change data received from an external device or vice versa.
Press the CONTROL LCD button to alternately turn control change
data reception and transmission ON (SEND&RECEIVE) and OFF.
• The Control setting is retained in
memory even when the power is
turned off if the BACKUP page MIDI
parameter is turned ON (page 107),
otherwise the default setting is
SEND&RECEIVE.
■ Start/Stop ..................................................................................................................
Normally the Clavinova will respond to MIDI start and stop commands received from an external MIDI device or keyboard, causing the
auto-accompaniment or song record/playback functions to start or stop in
the same way as the panel [START/STOP] button. The Clavinova also
transmits MIDI start and stop commands when the corresponding functions are operated.
This function makes it possible to cancel start/stop command reception and transmission if you do not want the Clavinova to be affected by
start/stop commands received from an external device or vice versa.
Press the START/STOP LCD button to alternately turn start/stop
command reception and transmission ON (SEND&RECEIVE) and OFF.
96
• The Start/Stop setting is retained in
memory even when the power is
turned off if the BACKUP page MIDI
parameter is turned ON (page 107),
otherwise the default setting is
SEND&RECEIVE.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Utility Functions
MIDI 3
The MIDI 3 function page contains the TRANSPOSE and SEND parameters which determine whether
MIDI note data will be affected by the Transpose setting (page 91), and whether the ABC, rhythm, and
harmony data will be transmitted via the MIDI OUT terminal.
■ Transpose .................................................................................................................
The RECEIVE parameter determines whether MIDI note pitch received by the Clavinova will be affected by the setting of the Transpose
function (see page 91), while the SEND parameter determines whether
MIDI note pitch transmitted by the Clavinova will be affected by the
setting of the Transpose function.
Press the RECEIVE or SEND LCD button to alternately turn transposition of received or transmitted MIDI data ON and OFF.
• The actual note number received or
transmitted is not affected. The transposition is produced by the MIDI control change RPN coarse tune data.
• The MIDI Transpose settings are
retained in memory even when the
power is turned off if the BACKUP
page MIDI parameter is turned ON
(page 107), otherwise the RECEIVE
parameter is turned On and the SEND
parameter is turned OFF.
■ Send ................................................................................................................................
These parameters determine whether MIDI data corresponding to
ABC/rhythm and harmony playback will be transmitted via the MIDI
OUT terminal. Press the ABC&RHY or HARMONY button to alternately turn transmission of the corresponding data ON (9–16ch / 6–8ch)
or OFF. When on, the ABC and rhythm data is transmitted on MIDI
channels 9 through 16, and the harmony data is transmitted on channels
6 through 8.
• The Send settings are retained in
memory even when the power is
turned off if the BACKUP page MIDI
parameter is turned ON (page 107),
otherwise both parameters are turned
OFF.
• If you intend to send the ABC/rhythm
or harmony data via MIDI, it is a good
idea to set the BASIC and LEFT/2
channels (page 94) to the different
channels than the ones used for ABC/
rhythm (9…16) and harmony (6…8)
data to avoid data conflict problems.
• If either of these parameters is on, the
ABC/rhythm and/or harmony data will
be sent even if the BASIC send channel is turned OFF.
97
The Utility Functions
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Format
The FORMAT page provides access to the Disk Format function which allows new disks or disks
formatted on other equipment to be “formatted” for use with the Clavinova.
The Clavinova uses only 3.5" 2DD or 2HD floppy disks. We recommend that you use Yamaha disks.
Before you can use a new disk for recording, the disk must be formatted so that the Clavinova can recognize it and correctly write the music data onto it.
Z Insert the Disk To Be Formatted ......................................................
Insert a new blank disk. Make sure that the disk’s write protect tab is
set to the “write” position (tab closed), and insert the new disk into the
disk drive unit with the sliding door facing the drive slot and the label
side of the disk facing upward. The disk should click securely into place,
and the disk drive lamp should light briefly. The “Start disk format?” display will automatically appear if an unformatted disk is inserted. Press the OK LCD button to format the disk or the CANCEL
LCD button to abort.
Write protect tab
closed (unlocked
— write enabled)
• If you access the FORMAT function
page via the [FUNCTION] and PAGE
buttons (i.e. you want to format a disk
that is already inserted), press the
START LCD button before proceeding
to step 2 below.
• “Protected disk!” will appear if a protected disk (DOC, etc.) that cannot be
formatted is loaded in the drive.
• The “No disk!” alert will appear if you
attempt to execute a format operation
when there is no disk inserted in the
disk drive.
• 2DD disks are formatted into 720 KB,
while 2HD disks are formatted into
1.44 MB.
• The song record or playback mode will
be turned off if the FORMAT operation
is executed while they are on.
X Confirm & Start the Format Operation ......................................
When “Are you sure?” appears press the YES LCD button to
confirm and continue, or the NO LCD button to cancel the operation.
This extra confirmation step is necessary because formatting completely
erases any data that is already on the disk — make sure that the disk
you’re about to format does not contain any important data!
Formatting will begin the instant you select “YES”. The progress of
the format operation will be indicated by a bar-graph on the display.
When formatting is complete, you can go ahead and record using the
Song Record function, use the Song Copy function to copy songs, or
save other data to the disk.
98
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Utility Functions
Registration
The REGISTRATION function page provides access to the Clavinova’s Registration and All Setup file
disk operations — save, load, delete, and rename.
Before selecting the Registration function, make sure that the disk you want to use for this operation is
inserted in the disk drive, and both the song record or playback modes are not engaged.
Z Select a File Type ..............................................................................................
Use either of the first two LCD buttons to select either REGISTRATION or ALL SETUP, according to the type of file you want to save,
load, delete, or rename.
Registration
A Registration file containing all data in the 25 or 15 Registration memories.
All Setup
An All Setup file containing all panel setup data in the list on
page 122 including Registration data.
• The Registration function cannot be
used when the song record or playback mode is engaged — the “Button
not valid!” alert display will appear.
• See page 58 for the list of data contained in the Registration memory.
X Select a File Operation ...............................................................................
Use the fourth LCD button to select the LOAD, SAVE, DELETE, or
RENAME operation.
C Press START ............................................................................................................
Press the START LCD button to begin the selected operation, then
proceed according to the selected operation as described below:
■ SAVE ...............................................................................................................................
If you select SAVE the name entry display will appear and you will
have to enter a name for the file to be saved.
99
The Utility Functions
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
An “empty” name appears in the upper right corner of the display.
Use the > LCD button to position the underline cursor where you want
to enter a character (file names can be up to 12 characters in length). Use
the data dial and/or the [+]/[–] buttons to select the character you want to
enter from the list in the center of the display, then press the c.set LCD
button to enter the character at the current cursor position. Repeat this
procedure until your name is complete. The c.del LCD button can be
used to back up one space and delete a character.
When the name is complete press the SAVE LCD button to save the
file with the name just entered, or CANCEL to abort.
If you enter a name that already exists on the disk, the “Same
name! Overwrite?” alert will appear. In this case press OK if it’s
OK to overwrite the original file with the new file, or CANCEL to abort
the save operation.
■ RENAME .....................................................................................................................
If you select RENAME, first use the FILE ▲ and ▼ LCD buttons to
select the file you want to rename, then press the START LCD button to
go to the name entry display. Enter a new file name in the same way as
described for SAVE, above, then press the OK LCD button to rename the
file with the name just entered, or CANCEL to abort. If you enter a name
that already exists on the disk, the “Same name! Overwrite?”
alert will appear. In this case press OK if it’s OK to overwrite the original file with the renamed file, or CANCEL to abort the rename operation.
■ LOAD ..............................................................................................................................
If you select LOAD, first use the FILE ▲ and ▼ LCD buttons to select the file you want to load, then press the START LCD button. When
the “Are you sure?” prompt appears, press YES to load the file or
NO to cancel.
100
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Utility Functions
■ DELETE .......................................................................................................................
If you select DELETE, first use the FILE ▲ and ▼ LCD buttons to
select the file you want to delete, then press the START LCD button.
When the “Are you sure?” prompt appears, press YES to delete the
file or NO to cancel.
Transform
The TRANSFORM function page allows CVP-79A/69/69A/59S performance (i.e. song) data files to be
converted to CVP Performance format so that the data can be played on other Clavinova models, or to
Yamaha Piano Format 1 or Piano Format 2 so that the data can be played on Yamaha Disklaviers.
Make sure that the disk (only 2dd type disks can be used for this operation) containing the song you
want to convert is inserted in the disk drive, and the song record mode is not engaged. Then select the
Transform function.
The available formats are compatible with the following Disklavier
and Clavinova models:
CVP PERFORMANCE
CVP-50/70/55/65/75/83S/85A/87A/89,
CLP-705, DOM-30, DOU-10
PIANO FORMAT 1
MX80 series.
Disklavier Grand.
MX100 MarkII.
Disklavier Grand MarkII
PIANO FORMAT 2
MX100A.
MX100B.
The converted data will automatically be saved to a free song number
and named according to the type of conversion selected:
CVP PERFORMANCE
“C)XXXXXX” where “XXXXXX” is the original song
name.
PIANO FORMAT 1/2
“P)XXXXXX” where “XXXXXX” is the original song
name.
Z Select the Conversion Type ...................................................................
• Only 2DD type disks can be used for
this operation. If a 2HD disk is used
the “2HD disk is not valid! Please copy
to 2DD disk.” alert display will appear.
In this case copy the song you want to
convert to a 2DD disk first (see “Song
Copy” below), and then try the conversion again.
• This function can not be used when
the song record mode is engaged —
the “Button not valid!” alert display will
appear.
• Only data on disk recorded by the
CVP-79A/69/69A/59S can be converted (data in the Clavinova’s internal
memory cannot be converted until it is
saved to disk).
• The copied data from the Disk Orchestra Collection disk (page 103) cannot
be converted.
• If data converted to PIANO FORMAT
1/2 is played back on the Clavinova,
tracks 1 and 2 will not sound.
• Record or edit functions cannot be
executed on a converted song.
• The original pre-converted data remains alive even after the conversion
has been executed.
Use either of the first two LCD buttons to select the target format of
the file: CVP PERFORMANCE, PIANO FORMAT 1, or PIANO
FORMAT 2.
101
The Utility Functions
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
X Select the Song Number to be Converted .............................
Use the SONG LCD button — or data dial or [+]/[–] buttons — to
select the song number to be converted.
C Start the Conversion .....................................................................................
Press the TRANSFORM LCD button to begin the conversion process.
When the conversion process is finished, the “Completed! SONG
No. XX” message will appear to inform you as to the SONG No. into
which the data was saved.
Song Copy
Song data can be “backed up” by copying to a new song number or a different disk, as follows:
(Make sure that the song record mode is not engaged before proceeding.)
Z Insert a Disk, Select the Song Copy Function, &
Select the Type of Copy Operation ...............................................
Insert the disk containing the song you want to copy, select the Song
Copy function, and use either of the first two LCD buttons to select
“DISK1 — 1” to copy to a different song within the same disk, or
“DISK1 — 2” to copy to a different disk.
X Select the Source Song Number .....................................................
Use the SONG—> LCD button to select the song you want to copy.
The data dial and [+]/[–] buttons can also be used once the SONG—> parameter has been selected. The selected song name will appear in the
upper right corner of the display.
C Select the Destination Song (DISK 1 – 1 type copy) ..
This step is for the DISK 1 – 1 type copy only. If you have selected the DISK 1 –
2 type copy, pass this step and proceed to the next V step.
Use the SONG button to select the song number you wish to copy to
(i.e. the destination song number). The data dial and [+]/[–] buttons can
also be used once the SONG parameter has been selected. If you select a
song number that already contains data, that data will be overwritten by
the new song data. If the destination song already contains data, the
name of the song file will appear in the middle right corner of the display.
102
• The song copy function cannot be
used when the song record mode is
engaged—the “Button not valid!” alert
display will appear.
• If the Clavinova’s internal memory
contains song data, the “CVP-DISK”
copy mode will be automatically selected to copy the internal memory
data to disk (see the “Copying Data
Recorded Without a Disk” below) and
the “DISK 1 – 1” or “DISK 1 – 2” copy
mode cannot be selected. In this case,
copy the internal memory data to disk
first, if you want to keep the data, and
delete the internal memory data by
using the Song Delete function (page
104). Then try the “DISK 1 – 1” or
DISK 1 – 2” copy operation again.
• Only song data recorded on the CVP79A/69/69A/59S and Disk Orchestra
Collection orchestra and rhythm data
can be copied using this function.
• Data cannot be copied to Disk Orchestra Collection disks, Disklavier disks, or
any write-protected disk.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Utility Functions
V Start Copying ........................................................................................................
Press the COPY LCD button to begin the actual copy operation. If
you are copying to the same disk the “Are you sure?” confirmation
prompt will appear. Press the OK LCD button to continue, or NO to cancel.
If you choose to copy to a different disk, the “No. of disk exchanges” display will appear to inform you of the number of times
the disk will have to be exchanged, because you may have to exchange
the source and destination disks a few times if the song being copied is
long and complex. Press OK to continue, or CANCEL to abort. If you
press OK, the Clavinova will prompt you to insert the source and destination disks as required. Insert the source or destination disk accordingly.
INSERT DISK 1
Insert source disk.
INSERT DISK 2
Insert destination disk.
• The copy operation is not effective if
the same song numbers are selected
as the Source song and the Destination song in the DISK1 – 1 type copy.
In this case the “Button not valid!” alert
will appear.
The first time the destination disk is inserted, the “Please select
destination song No.” display will appear. Use the SONG ▼▲
LCD buttons, or data dial or [+]/[–] buttons, to select the destination
song number. If the destination song already contains data, the name of
the song file will appear along with the song number, and the data will be
overwritten with the new song data. Press OK to execute the copy operation or CANCEL to abort.
While the data is being copied the number of times the disks will
have to be exchanged to complete the copy operation will be shown on
the display.
● Copying Disk Orchestra Disks ([ORCH/3-10TR] and
[RHYTHM] parts only)
All Disk Orchestra data except the right-hand and left-hand parts can
be copied to a separate disk by following the standard DISK 1 – 2
copy procedure outlined above. The copied data cannot, however, be
copied a second time to another disk.
● Copying Data Recorded Without a Disk
If you’ve used the Song Record function to record data without first
loading a disk: insert a formatted disk, select the Song Copy function,
then select the destination song number and copy as described above.
The “CVP - DISK” copy mode will automatically be selected and
the “CVP” will be selected as the source song when the internal
memory contains song data.
• Tracks 1 and 2 of a copied DOC song
can be recorded, but tracks 3 through
16 cannot be recorded.
• The Phrase Repeat function (page 69)
cannot be used on a copied DOC
song.
• The “DISK 1 – 1” and “DISK 1 – 2”
copy modes cannot be selected when
the internal memory contains song
data.
103
The Utility Functions
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Song Delete
You can delete any song from a loaded disk as follows:
(Make sure that the song record mode is not engaged before proceeding.)
ZInsert a Disk & Select the Song Delete Function ...........
Insert the disk containing the song you want to delete and select the
Song Delete function.
XSelect the Song to Delete ........................................................................
Use the SONG ▲ and ▼ buttons to select the song number you wish
to delete. The data dial and [+]/[–] buttons can also be used. It is also
possible to delete song data in the internal memory: select “CVP” instead of a song number. (“CVP” will appear and can be selected only
when the internal memory contains data.)
• The song delete function cannot be
used when the song record mode is
engaged — the “Button not valid!” alert
display will appear.
• Only song data recorded on the CVP79A/69/69A/59S can be deleted using
this function.
• Data cannot be deleted from writeprotected disks.
CConfirm & Execute the Delete Operation ...............................
Press the DELETE LCD button — “Are you sure?” will appear
on the display. Press the YES LCD button to immediately delete the selected song, or the NO LCD button if you wish to cancel the operation.
Micro Tuning
The Micro Tuning Feature makes it possible to individually tune each key on the Clavinova keyboard in
order to match different tuning standards. The pitch of each key can be raised or lowered by a maximum of
100 cents (approximately) from the standard pitch.
104
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Utility Functions
Z Select the Micro Tuning Function ...................................................
X Select a Key ............................................................................................................
Select the key you want to tune by pressing the key on the keyboard.
The selected key will appear on the display.
• The Micro-Tuning settings are retained
in memory even when the power is
turned off if the BACKUP page TUNE/
MICRO TUNING parameter is turned
ON (page 107), otherwise all keys are
set to “0”.
C Tune .................................................................................................................................
Use the TUNE s and t buttons to tune the selected key as required.
The data dial and [+]/[–] buttons can also be used. You can play the key
being tuned to check the sound during this operation. The maximum
tuning range is ±100 cents (100 cents = one semitone). The normal tuning (±0cent) for the selected key can be instantly recalled by simultaneously pressing the TUNE s and t buttons.
V Repeat as Necessary ....................................................................................
Repeat steps 2 and 3 until all the required keys have been tuned.
■ Disk Operations:
Saving, Loading, Renaming, and Deleting Micro-tuning Files ..................................................
Make sure that the disk you want to use for this operation is inserted
in the disk drive, and both the song record or playback modes are not
engaged before proceeding.
Z Select a File Operation ...............................................................................
Use the fourth LCD button to select the LOAD, SAVE, DELETE, or
RENAME operation.
• The Micro Tuning Disk Operations
cannot be used when the song record
or playback mode is engaged — the
“Button not valid!” alert will be displayed.
X Press START ............................................................................................................
Press the START LCD button to begin the selected operation, then
proceed according to the selected operation as described below:
105
The Utility Functions
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
■ SAVE ...............................................................................................................................
If you select SAVE the name entry display will appear and you will
have to enter a name for the file to be saved.
An “empty” name appears in the upper right corner of the display.
Use the > LCD button to position the underline cursor where you want
to enter a character (file names can be up to 12 characters in length). Use
the data dial and/or the [+]/[–] buttons to select the character you want to
enter from the list in the center of the display, then press the c.set LCD
button to enter the character at the current cursor position. Repeat this
procedure until your name is complete. The c.del LCD button can be
used to back up one space and delete a character.
When the name is complete press the SAVE LCD button to save the
file with the name just entered, or CANCEL to abort.
If you enter a name that already exists on the disk, the “Same
name! Overwrite?” alert will appear. In this case press OK if it’s
OK to overwrite the original file with the new file, or CANCEL to abort
the save operation.
■ RENAME .....................................................................................................................
If you select RENAME, first use the FILE ▲ and ▼ LCD buttons to
select the file you want to rename, then press the START LCD button to
go to the name entry display. Enter a new file name in the same way as
described for SAVE, above, then press the OK LCD button to rename the
file with the name just entered, or CANCEL to abort. If you enter a name
that already exists on the disk, the “Same name! Overwrite?”
alert will appear. In this case press OK if it’s OK to overwrite the original file with the renamed file, or CANCEL to abort the rename operation.
106
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Utility Functions
■ LOAD ..............................................................................................................................
If you select LOAD, first use the FILE ▲ and ▼ LCD buttons to select the file you want to load, then press the START LCD button. When
the “Are you sure?” prompt appears, press YES to load the file or
NO to cancel.
■ DELETE .......................................................................................................................
If you select DELETE, first use the FILE ▲ and ▼ LCD buttons to
select the file you want to delete, then press the START LCD button.
When the “Are you sure?” prompt appears, press YES to delete the
file or NO to cancel.
Backup
This function allows backup of various parameter settings to be turned on or off as required. To turn
backup for a parameter group on or off first use the ▲ and ▼ LCD buttons, data dial, or [+]/[–] buttons to
select the parameter group (see list below), and then use the ON/OFF LCD button to turn the selected parameter group on or off. An asterisk (“*”) appears before the name of a parameter group when backup is
turned on.
107
The Utility Functions
•
•
•
•
•
•
•
•
•
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
VOICE SETTING
TUNE/MICRO TUNING
PEDAL
MIDI
STYLE SETTING
ABC MODE
SONG SETTING
REGISTRATION
POPUP & ALERT
• The default settings for the BACKUP
function are ABC MODE, REGISTRATION, and POPUP & ALERT ON, the
other parameter groups OFF.
• The LCD contrast, help language and
this backup on/off setting itself are
always backed up.
* See page 122 for the list of parameters contained in each parameter group.
Parameters that are backed up will be retained in memory for about a
week if the Clavinova is not turned on during this time. All parameters
will be reset to their default values if the power remains off for longer
than about a week. To ensure that your backed-up settings are maintained, turn the power on for a few minutes at least once a week.
Recall
This function can be used to recall the initial factory settings for a range of parameters — individually
or all at once.
To recall a parameter group first use the ▲ and ▼ LCD buttons, data dial, or [+]/[–] buttons to select
the parameter group (see list below), and then press the START LCD button. When the “Are you
sure?” confirmation prompt appears, press YES to recall or NO to cancel.
•
•
•
•
•
•
VOICE SETTING
STYLE SETTING
SONG SETTING
REGISTRATION
MIDI
ALL SETUP
* See page 122 for the list of parameters contained in each parameter group.
108
• The initial LCD contrast, help language
and the above backup on/off settings
are not recalled by this function. These
and all other settings can be reset to
the initial factory values by turning the
power on while holding the C7 key.
When this is done the “Back up data
erased and replaced by Factory data.”
message will appear for a few seconds.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Utility Functions
Popup Time
Sets the amount of time the pop-up displays remain on the display screen before disappearing. The popup time of the voice/style displays can be set independently from all other pop-up displays.
Use the VOICE/STYLE or OTHERS [▲] and [▼] LCD buttons to set the pop-up time between 1 and
20 seconds as required. The data dial and [+]/[–] buttons can also be used once the desired parameter has
been selected. The default pop-up time (8 seconds) for either parameter can be recalled by pressing the
corresponding ▲ and ▼ LCD buttons simultaneously.
Song List Priority
This function determines whether a GM (general MIDI)/SMF or DOC (Disk Orchestra Collection) file
will take priority and be used for playback when encountered on the same disk. Use the corresponding
LCD button to select GM or DOC (default) as required.
Alert Sound
This function allows you to select one of six “Alert Voices” which will sound when an error is encountered, and set the alert volume.
Use the VOICE ▲ and ▼ LCD buttons to select the alert voice. The data dial and [+]/[–] buttons can
also be used once the VOICE parameter is selected. Press the VOLUME LCD button to select the volume
parameter and use the data dial or [+]/[–] buttons to set the volume as required. The volume range is from
“0” (no alert sound) to “100” (maximum volume). The default volume level (“50”) can be recalled instantly by pressing the [+] and [–] buttons simultaneously while the VOLUME parameter is selected.
• The default alert voice is “Steel
Drums”, and the alert voice will sound
automatically when you change the
alert voice.
109
Messages
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
When a disk related function button is pressed (ex. [PLAY]) and there is no disk in the
disk drive this prompt will appear. Put the proper disk in the drive and redo the procedure.
When renaming or copying the original song data this prompt will alert you in the event
that there is no song data in the selected song number, or in the disk. Re-select a
data-containing song, or put a disk with song data into the floppy disk drive.
This alert appears if there is no Registration Memory, Micro Tuning, or related data
other than song data on the currently inserted disk when you attempt a file-related
operation. Insert a disk with the proper data and do the procedure again.
This message appears when a new disk or a non Clavinova Formatted disk has been
put into the disk drive. Press OK if you want to format the disk. Press CANCEL if you
want to abort the formatting process.
The current disk is write protected and cannot be written to. Insert a disk that is not
write protected and try the procedure again.
You have attempted to edit or record over a song that was made on another system
(i.e. computer sequencer, etc.). Song data made on other systems cannot be edited or
recorded over. You can however, edit or record over any song that you have recorded
yourself on the CVP-79A/69/69A/59S.
A button that does not have a function in the current mode has been pressed. (ex. the
[GUIDE] button has been pressed when the Song Play mode is not engaged.)
The disk drive heads are dirty and should be cleaned. Clean the heads with a commercially-available floppy disk head cleaner.
An error occurred while writing to or reading from the disk. Try the operation again; if
the error occurs a second time the disk or drive may be faulty. If the drive has been
used for some time the heads may be dirty. Clean the heads with a commerciallyavailable floppy disk head cleaner. If the error still occurs with one disk and not others
the disk should be considered faulty and discarded. If the error occurs with all disks the
drive may be at fault. Refer the problem to your Yamaha dealer.
The disk operation (formatting, etc.) or data procedure is finished.
The disk is currently being accessed and must not be ejected from the drive.
When an operation such as DELETE is selected, this prompt will confirm that you want
to go ahead with the operation. Press YES to continue or NO to abort the operation.
The currently loaded disk is full and cannot hold anymore data. Delete any unnecessary data in the current disk, use a disk that has more available space or use a new
disk.
If this appears during song recording (in this case “OK” doesn’t appear), recording will
stop and recorded data up to that point will be saved automatically.
A single disk can only hold up to 60 files for each data type (song, style, registration,
etc.). If this message appears, insert a new disk or delete any unnecessary files in the
current disk. (Style Files cannot be deleted from the disk.)
110
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Messages
A file with the same name exists. Press OK if it is OK to overwrite the original file with
new data or press CANCEL to abort the operation.
Informs you of the number of times the disks must be exchanged when copying a
song to a different disk before the song copy operation starts.
When copying a song from the source disk to another disk, this message will ask you
to specify the song number to which the song is to be copied in the destination disk
when it is first inserted.
Insert the source disk to be copied in the song copy to a different disk operation.
Insert the destination disk to be copied to in the song copy to a different disk operation.
If the [EXIT] button is pressed prior to storing the recorded data in the CHORD SEQUENCE function this confirmation prompt will appear.
In the Song Recording INITIAL EDIT mode, if the [EXIT] button is pressed prior to
writing the edited data, this confirmation prompt will appear.
Only 2DD floppy disks can be used when converting data to the CVP Performance
format or Piano format. If a 2HD disk is used this alert will appear.
After the song data has been converted to CVP Performance format or Piano Format
this message will inform you as to the SONG No. into which the data was saved.
This message appears when the CUSTOM STYLE mode is engaged.
When you attempt to change the beat in the CUSTOM STYLE mode this confirmation
prompt will appear.
When you attempt to change the number of measures in the CUSTOM STYLE mode
this confirmation prompt will appear.
When the source style is a preset style or a style loaded from the optional Style File
disk, if you are recording new parts in the CUSTOM STYLE mode prior to clearing
data from parts other than R1 and R2, this confirmation prompt will appear.
When the STORE LCD button is pressed in the CUSTOM STYLE mode or when a
new source style is selected prior to storing the current style data this confirmation
prompt will appear.
111
Messages
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
When the [EXIT] button is pressed in the CUSTOM STYLE mode prior to storing the
current style data this confirmation prompt will appear.
If the CUSTOM STYLE mode’s RECALL SECTION operation cannot be carried out,
because the time signature has been changed, this alert will appear.
If the data has not been stored in memory before saving to disk in the CUSTOM
STYLE mode, this will prompt you to store the data before proceeding.
If there is not enough memory to store the data in the CUSTOM STYLE store operation, this alert will be displayed. It will be necessary to delete a style or simplify the
current style before storing the new style.
Appears when DELETE is selected in the previous message.
The memory has become full during recording or editing in the CUSTOM STYLE
mode. It will be necessary to simplify the style.
If this appears during song recording (in this case “OK” doesn’t appear), recording will
stop and recorded data up to that point will be saved automatically.
Some Style Files are too large for the LISTEN function to handle in the STYLE FILE
LOAD mode. In this case the data must be loaded into the internal memory in order to
be played.
When you attempt to LOAD a Style File and there is not enough memory to hold the
specified file this alert will be displayed. It will be necessary to delete a style before
loading the new style.
As long as the Clavinova is regularly used, data is retained in memory. This message
will appear if the power has not been turned on for quite some time (approximately one
week). In this case all data will be initialized to the factory-preset values. This message
also appears when you intentionally recall all the factory data by turning the power on
while holding the C7 key (see note on page 108).
A problem has been detected in the hardware system during power up. Refer the problem to your Yamaha dealer.
112
The Connectors
○○○○○○○○○○○○○○○○○○○○○○○
Although the Clavinova is a self-contained musical instrument that
simply be plugged into the AC mains outlet and played, it also
features a number of connectors for system expansion.
■ AUX IN L/L+R and R Jacks ........................................................................................
AUX IN
R
These jacks are intended primarily for use with
external synthesizers or tone generator modules.
For example, the outputs of the synthesizer/tone
generator can be to the Clavinova AUX IN jacks, allowing the sound of the synthesizer/tone generator to
be reproduced via the Clavinova’s internal amplifier
and speaker system. For monaural signal input (when
the connected device is monaural), use only the L/
L+R jack.
L/L+R
Tone Generator
• The input signal from the AUX
IN jacks is delivered to the AUX
OUT jacks, but is not affected
by the Clavinova’s volume
control or reverb effect.
■ AUX OUT L/L+R and R Jacks ..................................................................................
The AUX OUT L/L+R and R jacks deliver the
output of the Clavinova for connection to an instrument amplifier, mixing console, PA system, or recording equipment. If you will be connecting the
Clavinova to a monaural sound system, use only the
L/L+R jack. When a plug is inserted into the L/L+R
jack only, the left- and right-channel signals are combined and delivered via the L/L+R jack so you don’t
lose any of the Clavinova’s sound.
AUX OUT
R
L/L+R
Stereo System
• The AUX OUT jack signal must
never be returned to the AUX
IN jacks, either directly or
through external equipment.
■ MIDI IN, THRU and OUT Connectors
(MIDI IN and OUT on the CVP-59S) ...................................................................
CVP-79A/69/69A
MIDI
IN
OUT
MIDI Sequencer
THRU
Tone Generator
The MIDI IN connector receives MIDI data from
an external MIDI device (such as a synthesizer, sequencer, music computer, etc.) which can be used to
control the Clavinova. The MIDI THRU connector
provided on the CVP-79A, 69, and 69A re-transmits
any data received at the MIDI IN connector, allowing
“chaining” of several MIDI instruments or other devices. The MIDI OUT connector transmits MIDI data
generated by the Clavinova (e.g. note and velocity
data produced by playing the Clavinova keyboard).
■ EXP PEDAL Jack (CVP-79A) ....................................................................................
EXP PEDAL
An optional Yamaha FC7 Foot Controller can be
plugged into this jack for foot volume (expression)
control of the keyboard sound only (i.e. expression
doesn’t affect the auto-accompaniment sound or disk
playback). Press the pedal forward to increase volume,
and backward to decrease volume.
113
Troubleshooting
○○○○○○○○○○○○○○○○○○○○○○○
If you encounter what appears to be a malfunction, please check the
following points before assuming that your Clavinova is faulty.
1. No Sound When the Power is Turned On
Is the AC plug properly connected to the Clavinova and an AC wall outlet? Check the AC connection
carefully. Is the MASTER VOLUME control turned up to a reasonable listening level?
2. No Rhythm, ABC, or Song Playback Sound
Check the ABC/SONG VOLUME control setting. No sound is produced if it is set to the minimum position.
3. The Clavinova Reproduces Radio or TV Sound
This can occur if there is a high-power transmitter in your vicinity. Contact your Yamaha dealer.
4. Intermittent Static Noise
This is usually due to turning on or off a household appliance or other electronic equipment which is fed
by the same AC mains line as your Clavinova.
5. Interference Appears On Radio or TV Sets Located Near the Clavinova
The Clavinova contains digital circuitry which can generate radio-frequency noise. The solution is to
move the Clavinova further away from the affected equipment, or vice versa.
6. Distorted Sound When the Clavinova is Connected to An External Amplifier/Speaker
System
If the Clavinova is connected to a stereo system or instrument amplifier and the sound is distorted, reduce
the setting of the Clavinova volume control to a level at which the distortion ceases.
Options
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
● BC-8 Bench
A stable, comfortable bench styled to match your Yamaha
Clavinova.
● HPE-160 Stereo Headphones
High-performance lightweight dynamic headphones with extra-soft
ear pads.
● KC-883 Key Cover for the CVP-59S
A convenient way to keep your keyboard clean and dust-free.
114
• Some items may not be available in
certain areas.
Index
A
B
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
A-B repeat ............................................. 70
ABC freeze ............................................ 60
Accompaniment ..................................... 28
Alert & error displays, custom style ....... 53
Alert sound .......................................... 109
All delete, chord sequence .................... 82
Auto Bass Chord ................................... 34
Aux in jacks ......................................... 113
Aux out jacks ....................................... 113
Backup ................................................. 107
Backup parameter list .......................... 122
Bank, registration ................................... 59
Beat display ........................................... 31
Beat, custom style ................................. 46
Break, left pedal ..................................... 32
C
Center pedal .......................................... 26
Check play, chord sequence ................. 82
Chord assist ........................................... 40
Chord sequence recording .................... 80
Clock ...................................................... 95
Connectors .......................................... 113
Contrast button ...................................... 11
Control change ...................................... 96
Custom style .......................................... 45
Custom style playback ........................... 52
CVP-59S assembly ............................. 150
CVP-69/69A assembly ........................ 142
CVP-79A assembly ............................. 136
D
Damper mode (CVP-79A) ..................... 94
Damper pedal ........................................ 26
Damper range ........................................ 93
Delete, chord sequence ....................... 101
Delete, registration file ........................... 82
Demo tunes ........................................... 14
Demonstration Playback ........................ 13
Detune depth ......................................... 18
Disk orchestra collection playback ........ 61
Disk styles, loading ................................ 55
Disk, custom style .................................. 52
Display ..................................................... 8
Display hold button .................................. 9
Drum/key assignment list .................... 121
Dual mode ............................................. 17
E
F
I
Initial edit ............................................... 85
Introduction ............................................ 30
K
Key Cover ................................................ 3
Keyboard percussion ............................. 16
Keyboard utilities ................................... 91
L
LCD buttons ............................................. 8
Left pedal function ................................. 93
Left pedal ............................................... 27
Left pedal, harmony ............................... 43
Load, registration file ........................... 100
Local control .......................................... 95
M
Memory backup ..................................... 12
Messages ............................................ 110
Metronome ............................................ 33
Micro tuning ......................................... 104
Micro tuning disk operations ................ 105
MIDI 1 utilities ........................................ 94
MIDI 2 utilities ........................................ 95
MIDI 3 utilities ........................................ 97
MIDI connectors .................................. 113
MIDI data format .................................. 124
MIDI implementation chart ................... 156
MIDI reception ....................................... 94
Mixer button ........................................... 10
Multi-track recording & playback ........... 75
Music data, playing other types ............. 71
Music Stand ............................................. 3
Mute ....................................................... 64
N
Name, custom style ............................... 49
O
Octave shift ............................................ 91
One touch setting .................................. 44
Options ................................................ 114
P
Page buttons ......................................... 10
Pan ........................................................ 92
Panel controls .......................................... 4
Part assignment ..................................... 65
Part depth, reverb .................................. 23
Part selection ......................................... 63
Pause .................................................... 70
Pedal utilities ......................................... 92
Phrase repeat ........................................ 69
Playback start/stop ................................ 62
Polyphony .............................................. 16
Popup time .......................................... 109
Power Switch ........................................... 3
Precautions .............................................. 2
Preset recall, effect ................................ 25
Program change .................................... 96
Punch-in modes ..................................... 79
Punch-in/out recording .......................... 78
Effect depth ........................................... 25
Effect type list ........................................ 24
Effects, custom style .............................. 51
End mark, chord sequence .................... 82
End, chord sequence ............................. 82
Exit button .............................................. 10
Expression Pedal ..................................... 7
Expression pedal jack .......................... 113
Fast forward ........................................... 70
Fill-ins .................................................... 32
Fingered accompaniment ...................... 36
Fingering chart ..................................... 123
Floppy Disk Handling ............................... 2
Format, disk ........................................... 98
Full keyboard accompaniment ............... 37
G
Guide modes ......................................... 67
H
Harmony ................................................ 41
Headphones ............................................ 3
Help function .......................................... 11
Q
Quantize, custom style .......................... 48
Quantize, track ...................................... 84
Quick recording ..................................... 72
R
Recall ................................................... 108
Recall section, custom style .................. 50
Recording without a disk ....................... 89
Recording, song .................................... 72
Registration memory .............................. 58
Registration recall .................................. 60
Registration, disk ................................... 99
Rename, registration file ...................... 100
Renaming song files .............................. 87
Repeat ................................................... 69
Reverb type ...........................................
Rewind ...................................................
Rhythm ON/OFF, chord sequence ........
Right pedal ............................................
Root, chord ............................................
22
70
82
26
80
S
Second voice ......................................... 17
Send ...................................................... 97
Send channel ......................................... 94
Single finger accompaniment ................ 35
Small ABC ............................................. 39
Song copy ............................................ 102
Song delete ......................................... 104
Song list priority ................................... 109
Song number selection .................... 62, 73
Song playback ................................. 61, 89
Song recording ...................................... 72
Song repeat ........................................... 69
Sostenuto pedal ..................................... 26
Sound utilities ........................................ 92
Split mode .............................................. 19
Split point ............................................... 21
Split point, ABC ..................................... 39
Split voices ............................................ 19
Start, straight ......................................... 30
Start, synchronized ................................ 31
Start, tap ................................................ 31
Start/stop, MIDI ...................................... 96
Stop ....................................................... 32
Store, custom style ................................ 50
Style clear .............................................. 51
Style file load ......................................... 55
Style list ............................................... 120
Style selection ....................................... 28
T
Tempo control ........................................ 29
Time signature, custom style ................. 46
Total depth, reverb ................................ 23
Touch sensitivity .................................... 91
Track delete ........................................... 84
Track mix ............................................... 83
Track modes .................................... 73, 75
Track quantize ....................................... 84
Tracks, adding new ............................... 77
Transform ............................................ 101
Transpose .............................................. 91
Transpose, MIDI .................................... 97
Troubleshooting ................................... 114
Tune ...................................................... 92
Type, chord ............................................ 80
U
Utility function selection ......................... 90
V
Voice balance, dual mode ..................... 18
Voice balance, split mode ...................... 20
Voice effects .......................................... 24
Voice list .............................................. 116
Voice selection ...................................... 15
Voice selection, song ............................. 66
Volume, ABC/Song ............................ 6, 37
Volume, custom style ............................ 51
Volume, master ....................................... 6
Volume, other .......................................... 7
Volume, part .......................................... 38
Volume, song ......................................... 65
Volume, song part ................................. 66
115
Voice List / Stimmenverzeichnis / Liste des voix /
Bank
Group
MSB LSB
Piano
E.Piano
Harpsichord
Vibes
Guitar
116
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
112
113
112
0
114
116
115
0
0
0
112
116
0
115
116
117
117
112
113
115
116
0
0
112
0
0
112
0
0
112
0
0
0
112
0
0
112
115
112
0
113
0
113
112
0
0
0
0
0
0
0
0
0
Element
Program
Number
CVP-79A
CVP-69/69A
CVP-59S
Pan
1
1
2
2
1
3
3
3
4
5
5
5
6
6
6
6
5
7
7
7
7
8
47
12
12
9
9
10
11
13
14
15
16
25
25
26
26
26
27
27
27
28
28
29
29
30
31
32
105
106
107
108
109
Grand Piano1
Grand Piano2
BrightPiano
Rock Piano
Mellow Piano
Elec.Grand
Piano EP 1
Piano EP 2
Honky Tonk
Elec.Piano
EP Jazz
Bell EP
DX EP Pop
DX EP Modern
Mallet EP
Crystal EP
Stage EP
Harpsichord1
Harpsichord2
Grand Harpsi
Harpsi Pop
Clavi
Harp
Vibes
Jazz Vibes
Celesta
Celesta 4ft
Glockenspiel
Music Box
Marimba
Xylophone
TubularBells
Dulcimer
Gut Guitar
Nylon Guitar
Steel Guitar
Folk Guitar
12Str Guitar
J.Gtr Mellow
Jazz Guitar
J.Gtr Hard
Rock Guitar1
Rock Guitar2
Mute Guitar
Pick Guitar
Ovrdr.Guitar
Dist.Guitar
GuitarHarmo.
Sitar
Banjo
Shamisen
Koto
Kalimba
Grand Piano1
Grand Piano2
BrightPiano
Rock Piano
Mellow Piano
—
Piano EP 1
Piano EP 2
Honky Tonk
Elec.Piano
EP Jazz
Bell EP
DX EP Pop
DX EP Modern
Mallet EP
Crystal EP
—
Harpsichord1
Harpsichord2
Grand Harpsi
—
Clavi
Harp
Vibes
—
Celesta
Celesta 4ft
Glockenspiel
Music Box
Marimba
Xylophone
TubularBells
Dulcimer
Gut Guitar
Nylon Guitar
Steel Guitar
—
—
J.Gtr Mellow
Jazz Guitar
—
Rock Guitar
—
—
Pick Guitar
Ovrdr.Guitar
Dist.Guitar
GuitarHarmo.
Sitar
Banjo
Shamisen
Koto
Kalimba
Grand Piano1
Grand Piano2
BrightPiano
Rock Piano
Mellow Piano
—
Piano EP 1
Piano EP 2
Honky Tonk
Elec.Piano
EP Jazz
Bell EP
DX EP Pop
DX EP Modern
Mallet EP
Crystal EP
—
Harpsichord1
Harpsichord2
Grand Harpsi
—
Clavi
Harp
Vibes
—
Celesta
Celesta 4ft
Glockenspiel
Music Box
Marimba
Xylophone
TubularBells
Dulcimer
Gut Guitar
Nylon Guitar
Steel Guitar
—
—
J.Gtr Mellow
Jazz Guitar
—
Rock Guitar
—
—
Pick Guitar
Ovrdr.Guitar
Dist.Guitar
GuitarHarmo.
Sitar
Banjo
Shamisen
Koto
Kalimba
c
k
c
c
c
k
k
c
c
c
k
k
c
k
k
c
k
k
k
k
k
c
c
k
c
c
k
c
c
k
c
c
c
k
c
c
k
c
k
c
k
c
k
k
c
c
c
c
c
c
c
c
c
CVP-79A CVP-69/69A CVP-59S
2 (S)
1
2 (S)
1
2 (S)
2
2
2
2
2
2
2
2
1
2
2
2
1
1
2
2
1
1
2
1
1
1
1
2
1
1
1
2
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
—
2
2
2
2
2
2
2
1
1
2
—
1
1
2
—
1
1
2
—
1
1
1
2
1
1
1
2
1
1
1
—
—
1
1
—
2
—
—
1
1
1
1
1
1
1
1
1
2
1
2
1
1
—
2
2
2
2
2
2
2
1
1
2
—
2
1
2
—
1
1
2
—
1
1
1
2
1
1
1
2
1
1
1
—
—
1
1
—
2
—
—
1
1
1
1
1
1
1
1
1
Usable
Range
A-1~C7
A-1~C7
A-1~C7
A-1~C7
A-1~C7
A-1~C7
A-1~C7
A-1~C7
A-1~C7
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
F2~F5
F2~F5
C3~C7
C2~C6
C4~C7
C3~C5
C2~C6
F3~C6
C3~F4
C3~C5
E1~C5
E1~C5
E1~C5
E1~C5
E1~C5
E1~D5
E1~D5
E1~D5
E1~D5
E1~D5
E1~D5
E1~D5
E1~D5
E1~D5
E1~D5
C2~F4
C2~C5
D2~G4
G2~C5
C2~G4
Lista de voces
Bank
Group
MSB LSB
Clavi. tone/
synth
Organ
Strings /
Choir
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
112
0
115
0
0
0
0
0
0
0
112
112
112
112
0
0
0
0
0
0
0
0
0
115
115
0
0
0
112
115
0
0
115
0
0
115
0
0
112
113
0
0
115
112
0
0
0
112
0
0
0
0
0
0
0
0
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Element
Program
Number
CVP-79A
CVP-69/69A
CVP-59S
Pan
89
89
89
90
91
92
93
94
95
96
102
93
95
97
97
98
99
100
101
102
103
104
20
20
17
17
18
19
19
19
21
22
22
24
23
49
49
50
49
49
51
52
53
53
53
54
55
41
41
42
43
44
111
45
46
56
Clavinova T.
New Age Pad1
New Age Pad2
Warm Pad
PolySynthPad
Choir Pad
Bowed Pad
Metallic Pad
Halo Pad
Sweep Pad
Cosmic Pad
Ice Pad
Techno Pad
SynthCrystal
Rain
SoundTrack
Crystal
Atmosphere
Brightness
Goblins
Echoes
Sci-Fi
Pipe Organ
Chapel Organ
Draw 16 Organ
Draw 8 Organ
Perc. Organ
Rock Organ
Trem.Organ 1
Trem.Organ 2
Reed Organ
French Accrd
Accordion
Tango Accrd.
Harmonica
Orch.Strings
Strings
Strings Slow
Strings Soft
Chamber Str
Syn.Strings1
Syn.Strings2
Choir
Chapel Choir
Synth Choir
Voice Oohs
Synth Voice
Violin 1
Violin 2
Viola
Cello
Contrabass
Fiddle
Trem.Strings
Pizzicato
OrchestraHit
Clavinova T.
New Age Pad1
New Age Pad2
Warm Pad
PolySynthPad
Choir Pad
Bowed Pad
Metallic Pad
Halo Pad
Sweep Pad
Cosmic Pad
Ice Pad
Techno Pad
SynthCrystal
Rain
SoundTrack
Crystal
Atmosphere
Brightness
Goblins
Echoes
Sci-Fi
Pipe Organ
Chapel Organ
Draw 16 Organ
Draw 8 Organ
Perc. Organ
Rock Organ
—
—
Reed Organ
French Accrd
Accordion
Tango Accrd.
Harmonica
Orch.Strings
Strings
Strings Slow
Strings Soft
Chamber Str
Syn.Strings1
Syn.Strings2
Choir
Chapel Choir
Synth Choir
Voice Oohs
Synth Voice
—
Violin
Viola
Cello
Contrabass
Fiddle
Trem.Strings
Pizzicato
OrchestraHit
Clavinova T.
New Age Pad1
New Age Pad2
Warm Pad
PolySynthPad
Choir Pad
Bowed Pad
Metallic Pad
Halo Pad
Sweep Pad
Cosmic Pad
Ice Pad
Techno Pad
SynthCrystal
Rain
SoundTrack
Crystal
Atmosphere
Brightness
Goblins
Echoes
Sci-Fi
Pipe Organ
Chapel Organ
Draw 16 Organ
Draw 8 Organ
Perc. Organ
Rock Organ
—
—
Reed Organ
French Accrd
Accordion
Tango Accrd.
Harmonica
Orch.Strings
Strings
Strings Slow
Strings Soft
Chamber Str
Syn.Strings1
Syn.Strings2
Choir
Chapel Choir
Synth Choir
Voice Oohs
Synth Voice
—
Violin
Viola
Cello
Contrabass
Fiddle
Trem.Strings
Pizzicato
OrchestraHit
k
c
c
c
c
c
c
c
c
c
k
k
k
k
c
c
c
c
c
c
c
c
c
k
c
c
c
c
k
c
c
c
c
c
c
c
k
k
k
k
c
c
c
k
c
c
c
k
c
c
c
c
c
c
c
c
CVP-79A CVP-69/69A CVP-59S
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2 (S)
2
2
1
1
2
1
2
1
2
2
1
1
2
1
1
1
1
2
2
2
1
2
1
1
1
1
1
1
1
1
2
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2 (S)
1
2
1
1
2
—
—
1
2
2
1
1
2
1
1
1
1
2
2
2
1
2
1
1
—
1
1
1
1
1
2
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2 (S)
1
2
1
1
2
—
—
1
2
2
1
1
2
1
1
1
1
2
2
2
1
2
1
1
—
1
1
1
1
1
2
1
1
Usable
Range
C1~C7
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
G0~C6
G0~C6
G0~C6
C2~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C0~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
F2~A5
F2~A5
F2~F5
C3~C5
C0~C6
C0~C6
C0~C6
C0~C6
C1~C6
C0~C6
C0~C6
E1~E5
E1~E5
E1~E5
C2~G4
C2~C5
G2~C6
G2~C6
C2~E5
C1~E4
E0~G2
G2~C6
E0~C6
C1~C6
C2~C4
117
Voice List / Stimmenverzeichnis / Liste des voix / Lista de voces
Bank
Group
Brass
Sax / Flute
118
Program
MSB LSB Number
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
115
112
0
113
0
0
112
0
0
0
0
112
0
115
0
0
0
0
112
0
0
0
112
0
0
112
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
112
62
62
62
62
63
64
63
57
58
59
60
60
61
67
66
65
67
68
69
69
70
71
72
72
73
74
74
75
76
77
78
79
80
110
112
81
82
83
84
85
86
87
88
83
○○○○○○○○○○○○
Element
CVP-79A
CVP-69/69A
CVP-59S
Pan
CVP-79A CVP-69/69A CVP-59S
BigBnd Brass
Brass Sect.1
Brass Sect.2
Pop Brass
Synth Brass1
Synth Brass2
Analog Brass
Trumpet
Trombone
Tuba
MuteTrumpet1
MuteTrumpet2
French Horn
Breath Sax
Alto Sax
Soprano Sax
Tenor Sax
Baritone Sax
Oboe 1
Oboe 2
English Horn
Bassoon
Clarinet 1
Clarinet 2
Piccolo
Flute 1
Flute 2
Recorder
Pan Flute
Blown Bottle
Shakuhachi
Whistle
Ocarina
Bagpipe
Shanai
Square Lead
Saw. Lead
CalliopeLead
Chiff Lead
Charang Lead
Voice Lead
Fifths Lead
Bass & Lead
Synth Wood
—
Brass Sect.1
Brass Sect.2
Pop Brass
Synth Brass1
Synth Brass2
—
Trumpet
Trombone
Tuba
MuteTrumpet1
MuteTrumpet2
French Horn
Breath Sax
Alto Sax
Soprano Sax
Tenor Sax
Baritone Sax
—
Oboe
English Horn
Bassoon
—
Clarinet
Piccolo
—
Flute
Recorder
Pan Flute
Blown Bottle
Shakuhachi
Whistle
Ocarina
Bagpipe
Shanai
Square Lead
Saw. Lead
CalliopeLead
Chiff Lead
Charang Lead
Voice Lead
Fifths Lead
Bass & Lead
Synth Wood
—
Brass Sect.1
Brass Sect.2
Pop Brass
Synth Brass1
Synth Brass2
—
Trumpet
Trombone
Tuba
MuteTrumpet1
MuteTrumpet2
French Horn
Breath Sax
Alto Sax
Soprano Sax
Tenor Sax
Baritone Sax
—
Oboe
English Horn
Bassoon
—
Clarinet
Piccolo
—
Flute
Recorder
Pan Flute
Blown Bottle
Shakuhachi
Whistle
Ocarina
Bagpipe
Shanai
Square Lead
Saw. Lead
CalliopeLead
Chiff Lead
Charang Lead
Voice Lead
Fifths Lead
Bass & Lead
Synth Wood
c
k
c
k
c
c
k
c
c
c
c
k
c
c
c
c
c
c
k
c
c
c
k
c
c
k
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
k
2
1
1
1
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
2
2
2
2
2
2
2
2
2
2
—
1
1
1
2
2
—
1
1
1
1
1
1
2
1
1
1
1
—
1
1
1
—
1
1
—
1
1
1
2
1
1
1
2
2
2
2
2
2
2
2
2
2
2
—
1
1
1
2
2
—
1
1
1
1
1
1
2
1
1
1
1
—
1
1
1
—
1
1
—
1
1
1
2
1
1
1
2
2
2
2
2
2
2
2
2
2
2
Usable
Range
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
A#2~A#5
A#0~D#4
F0~G2
A#2~A#4
F#2~A5
F1~F4
F#1~D#4
C#2~G#4
F#2~D#5
F#1~D#4
C#1~G#3
A#2~G5
A#2~G5
E2~A#4
A#0~F4
D2~G5
D2~G5
D4~C7
G2~F#6
C3~C6
C3~C6
C3~C6
C3~C6
G2~C5
C3~C6
C3~C5
C1~F4
C2~C4
A-1~C7
A-1~C7
C1~C6
C1~C6
C1~C6
C1~C6
C1~C6
A-1~C7
C2~C6
○○○○○○○○○○○○○
Voice List / Stimmenverzeichnis / Liste des voix / Lista de voces
Bank
Group
Bass
Drums/Perc.
Program
MSB LSB Number
Element
CVP-79A
CVP-69/69A
CVP-59S
Pan
CVP-79A CVP-69/69A CVP-59S
Usable
Range
0
0
0
0
0
0
0
0
0
0
0
0
0
0
127
127
112
0
115
112
0
113
114
0
0
0
0
115
0
0
0
0
33
33
33
34
34
34
34
35
36
37
38
37
39
40
1
9
Acous.Bass 1
Acous.Bass 2
Acous.Bass 3
E.Bass Slap
Finger Bass
Elec.Bass
Heavy Bass
Picked Bass
Fretless
Slap Bass 1
Slap Bass 2
Hammer Bass
Analog Bass
Synth Bass
Standard Kit
Room Kit
Acous.Bass 1
Acous.Bass 2
Acous.Bass 3
E.Bass Slap
Finger Bass
—
—
Picked Bass
Fretless
Slap Bass 1
Slap Bass 2
—
Analog Bass
Synth Bass
Standard Kit
Room Kit
Acous.Bass 1
Acous.Bass 2
Acous.Bass 3
E.Bass Slap
Finger Bass
—
—
Picked Bass
Fretless
Slap Bass 1
Slap Bass 2
—
Analog Bass
Synth Bass
Standard Kit
Room Kit
k
c
k
k
c
k
k
c
c
c
c
k
c
c
d
d
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
—
—
1
1
1
1
—
1
1
1
1
1
1
1
2
1
—
—
1
1
1
1
—
1
1
1
1
C0~F#3
E0~G2
E0~G2
E0~G2
E0~G2
E0~G2
E0~G2
E0~G2
E0~G2
E0~G2
E0~G2
E0~G2
E0~G2
E0~G2
*
*
127
127
127
127
127
127
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
17
25
26
33
41
49
48
113
114
115
116
117
118
119
120
121
122
123
124
125
128
126
127
Rock Kit
Electro kit
Analog Kit
Jazz Kit
Brush Kit
Classic Kit
Timpani
Tinkle Bell
Agogo
Steel Drums
Woodblock
Taiko Drum
Melodic Tom
Synth Drum
Reverse Cym.
Fret Noise
Breath Noise
Seashore
Bird Tweet
Telephone
Gunshot
Helicopter
Applause
Rock Kit
Electro kit
Analog Kit
Jazz Kit
Brush Kit
Classic Kit
Timpani
Tinkle Bell
Agogo
Steel Drums
Woodblock
Taiko Drum
Melodic Tom
Synth Drum
Reverse Cym.
Fret Noise
Breath Noise
Seashore
Bird Tweet
Telephone
Gunshot
Helicopter
Applause
Rock Kit
Electro kit
Analog Kit
Jazz Kit
Brush Kit
Classic Kit
Timpani
Tinkle Bell
Agogo
Steel Drums
Woodblock
Taiko Drum
Melodic Tom
Synth Drum
Reverse Cym.
Fret Noise
Breath Noise
Seashore
Bird Tweet
Telephone
Gunshot
Helicopter
Applause
d
d
d
d
d
d
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
c
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
2
1
1
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
2
1
1
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
2
1
1
2
2
*
*
*
*
*
*
E0~C2
C3~C5
C2~C5
C2~C5
C3~C4
C3~C4
C3~C4
C3~C4
C3~C4
C3~C4
C3~C4
C3~C4
C3~C4
C3~C4
C3~C4
C3~C4
C3~C4
* Refer to the “Drum/key Assignment List” on page 121.
* Siehe “Verzeichnis der Schlagzeugklänge” auf Seite 121.
* Reportez-vous à la “Liste d’assignation instrument de batterie/touche du clavier” donnée à la page 121.
* Consulte la “Lista de asignaciones de teclas/batería” en la página 121.
• Bank LSB: “0” refers to GM system level 1 voice allocation. (Some
GM voices not listed above are not selectable on the panel but
sound when the corresponding program numbers are received.)
• Pan: c=Center, k=Keyboard Scaling Pan, d=Drum Kit Pan.
• Element: (S)=Stereo voice.
• Bank LSB: “0” entspricht der Stimmenzuordnung “GM System
Level 1”. (Manche der oben aufgeführten GM-Stimmen sind nicht
über das Bedienfeld wählbar, können jedoch per MIDIProgrammwechsel gespielt werden.)
• Pan: c = Mitte, k = tastenskalierte Verschiebung, d = SchlagzeugAnordnung
• Element: (S) = Stereo-Stimme
• Bank LSB : “0” concerne l’assignation de voix GM System Level 1.
(Certaines voix GM ne sont pas indiquées dans la liste ci-dessus et ne
peuvent pas être sélectionnées au moyen des touches du panneau,
mais leur son est malgré tout produit à la réception de leur numéro de
programme.)
• Pan : c = Centre, k = Panoramique d’échelle du clavier,
d = Panoramique de kit de batterie.
• Element : (S) = Voix stéréo
• Bank LSB: “0” se refiere a la asignación de voces de nivel 1 del
sistema GM (algunas voces GM que no se enumeran arriba no pueden
seleccionarse en el panel, pero suenan cuando se reciben los
números de programa correspondientes.)
• Pan: c = central, k = efecto panorámico graduado del teclado,
d = efecto panorámico de juego de batería.
• Element: (S) = voz estereofónica.
119
Style List / Rhythmusverzeichnis /
Liste des styles / Lista de estilos
Group
POP
16BEAT
DANCE POP
ROCK
120
Style Name
BEAT
Group
BALLAD
Style Name
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
BEAT
Group
TRADITIONAL
Style Name
BEAT
Pop Ballad 1
4/4
Jazz Ballad1
4/4
March 1
4/4
Pop Ballad 2
4/4
Jazz Ballad2
4/4
March 2
4/4
Light Pop
4/4
Slow Rock 1
4/4
Polka
4/4
Piano Ballad
4/4
Slow Rock 2
4/4
6/8 March
4/4
Organ Ballad
4/4
Blues
4/4
Tarantella
4/4
8Beat
4/4
BigBandBalad
4/4
Showtune
4/4
Folk
4/4
Gospel
3/4
Show Time
4/4
Pop Rhumba
4/4
Enka
4/4
Overture
4/4
NewAge
4/4
Pops Enka
4/4
Ragtime
2/4
16Bt Ballad1
4/4
Swing
4/4
Bluegrass
4/4
16Bt Ballad2
4/4
Cool Jazz
4/4
8Beat Cntry
4/4
16Bt Ballad3
4/4
Uptempo Jazz
4/4
Country Rock
4/4
16Beat Pop
4/4
Bigband Jazz
4/4
Country Pop
4/4
Funk
4/4
Dixieland
4/4
Folk Rock
4/4
Fusion
4/4
Boogie
4/4
Country Shfl
4/4
Fusion Balad
4/4
Charleston
4/4
Cntry 2 Step
4/4
Fusion Shffl
4/4
2Beat Swing
4/4
Cntry Ballad
4/4
Funky Jazz
4/4
Foxtrot
4/4
CowboyBoogie
4/4
Dance Pop1
4/4
Trad. Swing
4/4
Trad. Wlatz1
3/4
Dance Pop2
4/4
Rhumba 1
4/4
Trad. Waltz2
3/4
Eurobeat
4/4
Rhumba 2
4/4
CntryT.Waltz
3/4
Techno
4/4
Mambo
4/4
Vienna Waltz
3/4
Synth Boogie
4/4
Tango
4/4
Flamenco
3/4
Disco Soul
4/4
Cha Cha
4/4
Jazz Waltz
3/4
Party Pop
4/4
Bolero
4/4
Swing Waltz
3/4
Tropical
4/4
Beguine
4/4
Cntry Waltz
3/4
Upbeat Pop
4/4
Merengue
4/4
Slow Waltz
3/4
Rock Ballad
4/4
Son
4/4
Gospel Waltz
3/4
Rock & Roll
4/4
Bossanova1
4/4
Rock Shuffle
4/4
Bossanova2
4/4
Pop Shuffle
4/4
Pop Bossa
4/4
Jazz Rock
4/4
Reggae
4/4
Twist
4/4
Pop Reggae
4/4
Soul
4/4
Samba 1
4/4
Rhythm&Blues
4/4
Samba 2
4/4
Jazz Samba
4/4
Salsa
4/4
JAZZ
LATIN
LATIN POP
COUNTRY
WALTZ
Drum/key Assignment List / Verzeichnis der Schlagzeugklänge /
Liste d’assignation instrument de batterie/touche du clavier /
Lista de asignaciones de teclas/batería
Keyboard
MIDI
Key Alternate
Room Kit
Note
Note# Note off assign Standard Kit
C#1
13 C#-1
3
Surdo Mute
<——
D1
14 D-1
3
Surdo Open
<——
D#1
15 D#-1
Hi Q
<——
E1
16 E-1
Whip Slap
<——
F1
17 F-1
4
Scratch Push <——
F#1
18 F#-1
4
Scratch Pull
<——
G1
19 G-1
Finger Snap
<——
G#1
20 G#-1
Click Noise
<——
A1
21 A-1
Metronome Click <——
A#1
22 A#-1
Metronome Bell <——
B1
23 B-1
Seq Click L
<——
C2
24 C0
Seq Click H
<——
C#2
25 C#0
Brush Tap
<——
D2
26 D0
O
Brush Swirl L <——
D#2
27 D#0
Brush Slap
<——
E2
28 E0
O
Brush Swirl H <——
F2
29 F0
O
Snare Roll
<——
F#2
30 F#0
Castanet
<——
G2
31 G0
Snare L
<——
G#2
32 G#0
Sticks
<——
A2
33 A0
Bass Drum L
<——
A#2
34 A#0
Open Rim Shot <——
B2
35 B0
Bass Drum M <——
C3
36 C1
Bass Drum H BD Room
C#3
37 C#1
Side Stick
<——
D3
38 D1
Snare M
<——
D#3
39 D#1
Hand Clap
<——
E3
40 E1
Snare H
<——
F3
41 F1
Floor Tom L
Room Tom 1
F#3
42 F#1
1
Hi-Hat Closed <——
G3
43 G1
Floor Tom H
Room Tom 2
G#3
44 G#1
1
Hi-Hat Pedal
<——
A3
45 A1
Low Tom
Room Tom 3
A#3
46 A#1
1
Hi-Hat Open
<——
B3
47 B1
Mid Tom L
Room Tom 4
C4
48 C2
Mid Tom H
Room Tom 5
C#4
49 C#2
Crash Cymbal 1 <——
D4
50 D2
High Tom
Room Tom 6
D#4
51 D#2
Ride Cymbal 1 <——
E4
52 E2
Chinese Cymbal <——
F4
53 F2
Ride Cymbal Cup <——
F#4
54 F#2
Tambourine
<——
G4
55 G2
Splash Cymbal <——
G#4
56 G#2
Cowbell
<——
A4
57 A2
Crash Cymbal 2 <——
A#4
58 A#2
Vibraslap
<——
B4
59 B2
Ride Cymbal 2 <——
C5
60 C3
Bongo H
<——
C#5
61 C#3
Bongo L
<——
D5
62 D3
Conga H Mute <——
D#5
63 D#3
Conga H Open <——
E5
64 E3
Conga L
<——
F5
65 F3
Timbale H
<——
F#5
66 F#3
Timbale L
<——
G5
67 G3
Agogo H
<——
G#5
68 G#3
Agogo L
<——
A5
69 A3
Cabasa
<——
A#5
70 A#3
Maracas
<——
B5
71 B3
O
Samba Whistle H <——
C6
72 C4
O
Samba Whistle L <——
C#6
73 C#4
Guiro Short
<——
D6
74 D4
O
Guiro Long
<——
D#6
75 D#4
Claves
<——
E6
76 E4
Wood Block H <——
F6
77 F4
Wood Block L <——
F#6
78 F#4
Cuica Mute
<——
G6
79 G4
Cuica Open
<——
G#6
80 G#4
2
Triangle Mute <——
A6
81 A4
2
Triangle Open <——
A#6
82 A#4
Shaker
<——
B6
83 B4
Jingle Bell
<——
C7
84 C5
Bell Tree
<——
Rock Kit
Electro Kit
Analog Kit
Jazz Kit
Brush Kit
Classic Kit
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
SD Rock M
<——
Bass Drum M
<——
Bass Drum H 3
BD Rock
<——
SD Rock
<——
SD Rock Rim
Rock Tom 1
<——
Rock Tom 2
<——
Rock Tom 3
<——
Rock Tom 4
Rock Tom 5
<——
Rock Tom 6
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Reverse Cymbal
<——
Hi Q
Snare M
<——
Bass Drum H 4
<——
BD Rock
BD Gate
<——
SD Rock L
<——
SD Rock H
E Tom 1
<——
E Tom 2
<——
E Tom 3
<——
E Tom 4
E Tom 5
<——
E Tom 6
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Scratch Push
Scratch Pull
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Reverse Cymbal
<——
Hi Q
SD Rock H
<——
Bass Drum M
<——
BD Analog L
BD Analog H
Analog Side Stick
Analog Snare L
<——
Analog Snare H
Analog Tom 1
Analog HH Closed 1
Analog Tom 2
Analog HH Closed 2
Analog Tom 3
Analog HH Open
Analog Tom 4
Analog Tom 5
Analog Cymbal
Analog Tom 6
<——
<——
<——
<——
<——
Analog Cowbell
<——
<——
<——
<——
<——
Analog Conga H
Analog Conga M
Analog Conga L
<——
<——
<——
<——
<——
Analog Maracas
<——
<——
<——
<——
Analog Claves
<——
<——
Scratch Push
Scratch Pull
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
BD Jazz
<——
<——
<——
<——
Jazz Tom 1
<——
Jazz Tom 2
<——
Jazz Tom 3
<——
Jazz Tom 4
Jazz Tom 5
<——
Jazz Tom 6
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Brush Slap L
<——
<——
<——
<——
BD Soft
<——
Brush Slap
<——
Brush Tap
Brush Tom 1
<——
Brush Tom 2
<——
Brush Tom 3
<——
Brush Tom 4
Brush Tom 5
<——
Brush Tom 6
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Gran Cassa
<——
<——
<——
<——
Jazz Tom 1
<——
Jazz Tom 2
<——
Jazz Tom 3
<——
Jazz Tom 4
Jazz Tom 5
Hand Cym.Open L
Jazz Tom 6
Hand Cym.Closed L
<——
<——
<——
<——
<——
Hand Cym.Open H
<——
Hand Cym.Closed H
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
• “<——” indicates the content is the same as that of Standard Kit.
• The Drum Kit voices respond to and transmit the corresponding MIDI note
numbers.
• Key Off: Keys marked “ O” stop sounding the instant they are released.
• Alternate Assign: Playing any instrument within a numbered group will immediately stop the sound of any other instrument in the same group of the same
number.
• “<——” bedeutet “wie Standard Kit”.
• Die Schlagzeug-Stimmen sprechen auf MIDI-Notennummern an und
übertragen entsprechende Nummern.
• Key Off: Durch “ O” gekennzeichnete Klänge verstummen beim Loslassen der
Taste.
• Alternate Assign: Mit derselben Nummer gekennzeichnete Klänge werden von
demselben Instrument erzeugt und können daher nicht gleichzeitig produziert
werden. Spielt einer dieser Klänge gerade, wird er beim Anschlagen einer
anderen Taste mit derselben “Alternate Assign”-Nummer stummgeschaltet.
• “<——” indique que le contenu est le même que celui de “Standard Kit”.
• Les voix “Drum Kit” répondent aux et transmettent les numéros de note MIDI
correspondant.
• Key off : Le son produit par les touches marquées “ O” cesse à l’instant où la
touche est relâchée.
• Alternate Assign : Le fait de jouer un instrument appartenant à un groupe ayant
un numéro arrête immédiatement le son de tout autre instrument appartenant à
un groupe ayant le même numéro.
• “<——” indica que el contenido es el mismo que el del juego estándar.
• Las voces del juego de batería responden a los números de notas MIDI
correspondientes y los transmiten.
• Key Off: Las teclas marcadas con “ O” dejan de sonar en el momento en que se
sueltan.
• Alternate Assign: Al tocar algún instrumento con un grupo numerado detendrá
inmediatamente el sonido de cualquier otro instrumento del mismo grupo con el
mismo número.
121
Backed Up Parameters / Dauerhaft gespeicherte Parameter /
Paramètres sauvegardés / Parámetros respaldados
VOICE SETTING
Keyboard Voice
Keyboard Volume
Split Point
Dual Mode
Split Mode
Dual Voice
Split Voice
Dual Balance
Split Balance
Dual Detune Depth
Reverb On/Off
Reverb Type
Reverb Depth
(Total, Rhythm, Bass,
Chord, Keyboard)
Effect On/Off
Effect Type
Effect Depth
(Main Voice)
(Dual Voice, Split Voice)
Touch Sensitivity
Right/1 Octave Shift
Left Octave Shift
2nd Octave Shift
Right/1 Pan
Left Pan
2nd Pan
Transpose
Voice within each group
STYLE SETTING
ABC On/Off
Small ABC On/Off
Harmony On/Off
Harmony Type
Style
Main A/B
Tempo
Rhythm Volume
Bass Volume
Chord Volume
Pad Volume
Phrase Volume
Harmony Volume
Metronome
One Touch Setting
Setup Selection
(CVP-79A/69/69A)
Style within each group
SONG SETTING
Song List Priority
Guide Mode
Part Assign
MIDI
Send Channel Right/1
Send Channel Left
Local On/Off
Clock Internal/External
122
Backup Recall Default
Backup Off
O
O
Grand Piano 1
O
O
100
O
O
F#2
—
O
Off
—
O
Off
O
O
Strings Slow
O
O
Acous. Bass 1
O
O
Center
O
O
Center
O
O
5
O
O
On
O
O
Hall 1
O
O
50
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
—
—
—
O
O
—
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Program Change Send
& Receive/Off
Control Change Send
& Receive/Off
Start/Stop Command
Send & Receive/Off
Transpose Receive On/Off
Transpose Send On/Off
ABC & Rhythm Send On/Off
Harmony Send On/Off
TUNE/MICRO TUNING
Tune
Micro-tuning
PEDAL
Left Pedal Function
Damper Range
Damper Mode (CVP-79A)
POPUP & ALERT
Voice/Style Popup Time
Others Popup Time
Alert Voice
Alert Volume
ABC MODE
ABC Mode
REGISTRATION
ALL SETUP
Preset for each voice
Preset for each voice
Preset for each voice
50
Normal
0
+1
0
Center
Center
Center
0
First voice within each group
Backup Off
Off
Off
Off
Trio
Pop Ballad 1
Main A
Preset for each style
90
90
90
90
90
90
Normal
First setup in the list
*
*
*
*
*
*
*
*
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
First style within each group
Backup Off
DOC
Next Note
Part1=Track1, Part2=Off
Backup Off
1 ch
Off
On
Internal
O
O
Send & Receive
O
O
Send & Receive
O
O
O
O
O
O
O
O
O
O
—
—
O
O
O
—
—
—
O
O
O
O
—
—
—
—
O
O
—
—
O
O
On
Off
Off
Off
Backup Off
440.0
0
Backup Off
Soft
R
Continuous
Backup On
8
8
Steel Drums
50
Backup On
Single Finger
Backup On
—
“REGISTRATION” includes all of the panel setup data in the 25 or 15 Registration memories.
See page 58 for a list of data contained in the Registration memory.
“ALL SETUP” includes all of the above parameters (including the “—” marked parameters)
and REGISTRATION data.
“REGISTRATION” schließt alle Bedienfeld-Setups in den 25 bzw. 15 RegistrationSpeicherplätzen mit ein. Eine Liste der in den Registration-Setups gespeicherten Daten
finden Sie auf Seite 58.
“ALL SETUP” schließt alle der obigen Parameter (auch die mit “—” markierten) sowie
REGISTRATION-Daten mit ein.
“REGISTRATION” comprend toutes les données de réglage de panneau contenues dans les
25 ou 15 emplacements de mémoire de registration. La liste des données contenues dans la
mémoire de registration est donnée à la page 58.
“ALL SETUP” comprend tous les paramètres et données de registration mentionnés cidessus, (y compris les paramètres indiqués par “—”).
“REGISTRATION” incluye todos los datos de ajustes del panel de las 25 ó 15 memorias de
registros. Vea la página 58 para encontrar la lista de los datos contenidos en la memoria de
registros.
“ALL SETUP” incluye todos los parámetros de arriba (incluyendo los parámetros marcados
con “—”) y los datos de REGISTRATION.
•
•
The LCD contrast, help language and this backup on/off setting itself are always backed up.
The initial LCD contrast, help language and this backup on/off setting itself are not recalled by
the recall function. These and all other settings can be reset to the initial factory values by
turning the power on while holding the C7 key.
Default Values: LCD contrast= 10, Help language= English
•
Die Displaykontrasteinstellung, die Spracheneinstellung sowie die BACKUP-Einstellungen
werden in jedem Fall dauerhaft gespeichert.
Die Displaykontrasteinstellung, die Spracheneinstellung sowie die BACKUP-Einstellung
selbst sind von der Rücksetzung durch die RECALL-Funktion ausgeschlossen. Diese und
alle anderen Einstellungen können auf die werkseitigen Standardwerte rückgesetzt werden,
indem Sie das Instrument bei gedrückt gehaltener C7-Taste einschalten.
Standardwerte: Displaykontrast = 10, Sprache für Help-Text = Englisch.
•
O
Backup Recall Default
O
O
Send & Receive
•
•
•
•
Les réglages de contraste de l’affichage, de langue de la fonction Aide et de la fonction
“Backup” sont toujours conservés en mémoire.
Le contraste de l’affichage, la langue de la fonction Aide et les réglages de la fonction
“Backup” d’origine ne peuvent pas être rappelés en utilisant la fonction de remise à l’état
initial “RECALL”. Ces réglages, comme tous les autres réglages, peuvent être rétablis en
mettant l’instrument sous tension tout en maintenant enfoncée la touche du clavier C7.
Default Values: LCD contrast= 10, Help language= English
Los ajustes del contraste del LCD, del idioma de ayuda y este ajuste de activación/
desactivación de respaldo siempre están respaldados.
Los ajustes iniciales del contraste del LCD, del idioma de ayuda y los ajustes de arriba de
activación/desactivación de respaldo no se activan con esta función. Estos y otros ajustes
podrá reponerse a sus valores iniciales de fábrica conectando la alimentación mientras se
mantiene presionada la tecla C7.
Valores de ajuste de fábrica: Contraste del LCD = 10, idioma de ayuda = Inglés
Fingering Chart / Akkordkiste /
Tablature / Gráfica de digitado
○○○○○○○○○○○○○○○
* All fingerings shown are simple root-position types.
* Die hier gezeigten Akkorde sind jeweils die Grundakkorde.
* Tous les doigtés indiqués sont du type à position fondamentale simple.
* Todos los digitados se muestran como tipos de posición de raíz sencilla.
Example for “C” chords
Beispiele für “C”-Akkorde
Exemples d’accords en “C”
Ejemplo de acordes “C”
CM 7 (b5)
CM 7 (#11)
C(b5)
Caug
Cm
Cm 6
Cm 7
Cmadd 9
Cm 7 (9)
Cm 7 (11)
CmM 7 (b5)
CmM 7 (9)
Cm (b5)
Cdim 7
C7
C 7 (#11)
C 7 (13)
C 7(b5)
C
C6
Cadd 9
CM 7 (9)
C 7(#5)
CM 7 (#5)
Cm 7 (b5)
CmM 7
)
)
)
)
)
(
(
)
)
(
)
(
)
(
C 7(#9)
)
C 7 (b13)
(
C 7(b9)
C 7 (9)
(
(
)
C7 sus 4
(
(
)
)
(
)
(
)
(
(
)
)
(
(
)
C 6 (9)
(
(
(
)
CM 7
Csus 4
123
MIDI Data Format / MIDI-Datenformat / Format des
If you’re already very familiar with MIDI, or are using a computer to control your music hardware with computer-generated MIDI messages, the data provided in this section can help you to control the Clavinova.
Falls Sie bereits mit MIDI vertraut sind oder einen Computer zur Hardware-Steuerung einsetzen, werden Ihnen die
nachfolgend aufgeführten Daten bei der Steuerung des Clavinovas wahrscheinlich hilfreich sein.
Si vous vous êtes déjà familiarisés avec l’interface MIDI, ou si vous utilisez un ordinateur pour commander votre
matériel de musique au moyen de messages MIDI générés par ordinateur, les données suivantes vous aideront à
commander le Clavinova.
Si ya está muy familiarizado con MIDI o si está usando una computadora para controlar su música con mensajes
MIDI generados por computadora, los datos proporcionados en esta sección le ayudarán a controlar la Clavinova.
• The Clavinova corresponds to a portion of the XG format, the Clavinova does not perfectly correspond to all XG
parameters.
1. Channel Messages
1.2.10 Harmonic Content
Cntrl#
71
1.1 Key On and Key Off
Receivable note range: C-2 to G8 (true voice A-1 to C7)
Velocity range: 1 to 127 (Value accepted only at Note On)
1.2 Control Change
If the Control Change Filter in Function [MIDI 2] is set to “ON” transmission and
reception are disabled.
Cntrl#
0
32
Parameter
Bank Select MSB
Bank Select LSB
Data Range
0:Normal, 127:Drum
0...127
A new bank selection does not become effective until receipt of the next
Program Change message.
Data Range
0...127
(0:-64, 64:+0, 127:+63)
Applies adjustment to the resonance value set by the voice. This parameter
specifies relative change, with value 64 producing zero adjustment. As values
get higher the sound becomes increasingly eccentric. Note that for some voices
the effective parameter range is narrower than the legal parameter range.
1.2.11 Release Time
Cntrl#
72
1.2.1 Bank Select
Parameter
Harmonic Content
Parameter
Release Time
Data Range
0...127
(0:-64, 64:+0, 127:+63)
Applies adjustment to the envelope release time set by the voice.
This parameter specifies relative change, with value 64 producing zero
adjustment.
1.2.12 Attack Time
1.2.2 Modulation
Cntrl#
1
Parameter
Modulation
Data Range
0...127
1.2.3 Data Entry
Cntrl#
6
38
Parameter
Data Entry MSB
Data Entry LSB
Data Range
0...127
0...127
Sets the value for the parameter specified by RPN/NRPN.
1.2.4 Main Volume
Cntrl#
7
Parameter
Volume MSB
Data Range
0...127
1.2.5 Pan
Cntrl#
10
Parameter
Panpot MSB
Data Range
0...127
0 = left; 127 = right
Cntrl#
73
Parameter
Attack Time
Data Range
0...127
(0:-64, 64:+0, 127:+63)
Applies adjustment to the envelope attack time set by the voice.
This parameter specifies relative change, with value 64 producing zero
adjustment.
Depending on the particular voice type, Attack Time data will have little or no
affect.
1.2.13 Brightness
Cntrl#
74
Parameter
Brightness
Data Range
0...127
(0:-64, 64:+0, 127:+63)
Applies adjustment to the cutoff frequency set by the voice. This parameter
specifies relative change, with value 64 producing zero adjustment. Lower
voices produce a softer sound. For some voices the effective parameter range is
narrower than the legal parameter range.
1.2.14 Portamento Control
1.2.6 Expression
Cntrl#
11
Parameter
Expression MSB
Data Range
0...127
1.2.7 Damper
Cntrl#
64
Parameter
Damper MSB
Data Range
0...127
Half pedal continuous data is received and accepted.
Parameter
Sostenuto
Data Range
0...127
(0-63:off, 64-127:on)
Cntrl#
67
Parameter
Soft Pedal
Data Range
0...127
Half pedal continuous data is received and accepted.
124
Data Range
0...127
1.2.15 Effect1 Depth ( Reverb Send Level )
Parameter
Effect1 Depth
Data Range
0...127
Adjusts the reverb send level.
1.2.16 Effect3 Depth ( Chorus Send Level )
Cntrl#
93
1.2.9 Soft Pedal
Parameter
Portamento Control
Message should be sent with Note On already sounding. The data value sets
the portamento source key number.
The channel with change from the currently sounding pitch to the next
received Note-On key using Portamento Time of 0.
Cntrl#
91
1.2.8 Sostenuto
Cntrl#
66
Cntrl#
84
Parameter
Effect3 Depth
Adjusts the chorus send level.
Data Range
0...127
donées MIDI / Formato de datos MIDI
1.2.17 Effect4 Depth ( Variation Effect Send Level )
Cntrl#
94
Parameter
Effect4 Depth
Data Range
0...127
when Variation Connection = 1 (System)
$1D $rr $mm
Drum Instrument Reverb Send Level
mm : $00 - $7F (0 to Max)
rr : drum instrument note number
$1E $rr $mm
Drum Instrument Chorus Send Level
mm : $00 - $7F (0 to Max)
rr : drum instrument note number
$1F $rr $mm
Drum Instrument Variation Send Level
mm : $00 - $7F (0 to Max)
rr : drum instrument note number
Adjusts the variation effect send level. Not effective if “Variation Connection”
is set to 0 (Insertion).
1.2.18 Data Increment / Decrement (for RPN)
Cntrl#
96
97
Parameter
RPN Increment
RPN Decrement
Data Range
0...127
0...127
The data byte has no meaning.
This message adds or subtracts 1 to/from the Pitchbend Sensitivity, Fine Tune,
and Coarse Tune MSBs. Note that the Increment (Decrement) message will not
change a setting that has already reached its maximum (minimum) value.
Incrementation or decrementation of the Fine Tune value never carries over to
the Coarse Tune value.
1.2.19 NRPN (Nonregistered parameter number)
Cntrl#
98
99
Parameter
RPN LSB
RPN MSB
Data Range
0...127
0...127
First send the NPRN MSB and LSB to select the control parameter, then set
the value by Data Entry.
The following NRPN values are supported.
○○○○○○○○○○○○
The LSB 14H-1FH (for drums) message will be accepted under the following
conditions, the channel must be set to the drum mode, and drum setups 1 or 2
must be set to that channel. (Default = drum setup 1.)
Note: The CVP 79A/69/69A/59S contain 3 drum setups (1 Preset Drum &
Drum Setup 1, 2). Preset Drum being the preset drum setup, its
parameters cannot be rewritten.
1.2.20 RPN (Registered parameter number)
Cntrl#
100
101
Parameter
RPN LSB
RPN MSB
Data Range
0...127
0...127
Default:7F 7FH
The following parameters are supported.
NRPN
Data entry
MSB LSB MSB
Parameter Data Range
00H 00H mmH
--
NRPN
Data entry
MSB LSB MSB
Parameter Data Range
Pitchbend Sensitivity
mm: 00-0cH(0-12 semitones:1 octave)
Can be set up 1 octave, in semitone units.
Default: 02H
LSB is ignored.
$01 $08 $mm
Vibrato Rate
mm : $00 - $40 - $7F (-64 - 0 - +63)
$01 $09 $mm
Vibrato Depth
mm : $00 - $40 - $7F (-64 - 0 - +63)
00H 01H mmH
11H
Fine Tuning
mm:00H-40H-7FH(-64-0-+63)
$01 $0A $mm
Vibrato Delay
mm : $00 - $40 - $7F (-64 - 0 - +63)
00H 02H mmH
--
$01 $20 $mm
Filter Cutoff Freq.
mm : $00 - $40 - $7F (-64 - 0 - +63)
7FH 7FH --
$01 $21 $mm
Filter Resonance
mm : $00 - $40 - $7F (-64 - 0 - +63)
RPN Null
Clears current RPN and NRPN number settings. Does
not change internal parameter settings.
$01 $63 $mm
EG Attack Time
mm : $00 - $40 - $7F (-64 - 0 - +63)
$01 $64 $mm
EG Decay Time
mm : $00 - $40 - $7F (-64 - 0 - +63)
$01 $66 $mm
EG Release Time
mm : $00 - $40 - $7F (-64 - 0 - +63)
$14 $rr $mm
Drum Filter Cutoff Freq.
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
$15 $rr $mm
Drum Filter Resonance
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
$16 $rr $mm
Drum EG Attack Rate
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
$17 $rr $mm
Drum EG Decay Rate
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
(Effects both Decay 1 and Decay 2)
$18 $rr $mm
Drum Instrument Pitch Coarse
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
$19 $rr $mm
Drum Instrument Pitch Fine
mm : $00 - $40 - $7F (-64 - 0 - +63)
rr : drum instrument note number
$1A $rr $mm
Drum Instrument Level
mm : $00 - $7F (0 to Max)
rr : drum instrument note number
$1C $rr $mm
Drum Instrument Panpot
mm : $00, $01 - $40 - $7F (Random, L − C − R)
rr : drum instrument note number
--
Course Tuning
mm:28H - 40H - 58H(-24-+24 semitones)
LSB is ignored.
1.2.21 Channel Mode Messages
The following Channel Mode messages are supported. (But the actual mode is fixed to
Poly and can not be changed.)
2nd byte
120
121
123
124
125
126
127
3rd byte
0
0
0
0
0
0 ~ 16
0
All Sound Off
Reset All Controllers
All Notes Off
Omni Off
Omni On
Mono
Poly
1.2.21.1 All Sound Off
Switches off all sound from the channel. Does not reset Note On and Hold On
conditions established by Channel Messages.
1.2.21.2 Reset All Controllers
Resets controllers as follows.
Controller
Pitchbend change
Modulation
Expression
Damper Pedal
Sostenuto
Soft Pedal
Portamento Control
RPN
NRPN
Value
+-0 (center)
0 (off)
127 (max)
0 (off)
0 (off)
0 (off)
Resets portamento source note number
Sets number to null. (Internal data remains unchanged.)
Sets number to null. (Internal data remains unchanged.)
125
MIDI Data Format / MIDI-Datenformat / Format des donées MIDI / Formato de datos MIDI
1.2.21.3 All Notes Off
2.1.3 Universal Non-Realtime Message
Switches off all of the channel’s “on” notes. Any notes being held by HOLD1 or
SOSTENUTO continue to sound until HOLD1/SOSTENUTO goes off.
2.1.3.1 General MIDI Mode On
1.2.21.4 Omni Off
Same processing as for All Notes Off.
1.2.21.5 Omni On
Same processing as for All Notes Off.
1.2.21.6 Mono
11110000
01111110
01111111
00001001
00000001
11110111
or
11110000
01111110
0xxxnnnn
F0
7E
7F
09
01
F7
= Exclusive status
= Universal Non-Realtime
= ID of target device
= Sub-ID #1=General MIDI Message
= Sub-ID #2=General MIDI On
= End of Exclusive
F0
7E
XN
00001001
00000001
11110111
09
01
F7
= Exclusive status
= Universal Non-Realtime
= When N is received N=0~F, whichever is received.
X = don't care
= Sub-ID #1=General MIDI Message
= Sub-ID #2=General MIDI On
= End of Exclusive
Same processing as for All Sound Off.
1.2.21.7 Poly
Same processing as for All Sound Off.
1.3 Program Change
If the Program Change Filter in Function [MIDI 2] is set to “ON” transmission and
reception are disabled.
1.4 Pitchbend
2.1.4 XG Native Parameter Change
2. System Exclusive Messages
2.1 Parameter Change
The CVP 79A/69/69A/59S models support the following Parameter Change messages.
[UNIVERSAL REALTIME MESSAGE ]
1) Master Volume
[UNIVERSAL NON-REALTIME MESSAGE ]
3) General MIDI Mode On
[XG NATIVE ]
1) XG System on
2) XG System Data parameter change
3) Multi Effect1 Data parameter change
4) Drum Setup Data parameter change
[Others]
1) Master tuning
2) Channel Detune
3) Volume & Expression Realtime Control off
2.1.2 Universal Realtime Message
2.1.2.1 Master Volume
11110000
01111111
01111111
00000100
00000001
0sssssss
0ttttttt
11110111
or
11110000
01111111
0xxxnnnn
F0
7F
7F
04
01
*SS
TT
F7
= Exclusive status
= Universal Realtime
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
F0
7F
XN
00000100
00000001
0sssssss
0ttttttt
11110111
04
01
SS
TT
F7
= Exclusive status
= Universal Realtime
= When N is received N=0~F, whichever is received.
x = don't care
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
11110000
01000011
0001nnnn
F0
43
1n
01001100
0aaaaaaa
0aaaaaaa
0aaaaaaa
0ddddddd
|
11110111
4C
aaaaaaa
aaaaaaa
aaaaaaa
ddddddd
|
F7
Exclusive status
YAMAHA ID
When n is received n=0~F, whichever is received.
When n is transmitted n always=0.
Model ID of XG
Address High
Address Mid
Address Low
Data
End of Exclusive
Data size must match parameter size (2 or 4 bytes).
2.1.4.1 XG System On
11110000
01000011
0001nnnn
F0
43
1N
01001100
0aaaaaaa
0aaaaaaa
0aaaaaaa
00000000
11110111
4C
00
00
7E
00
F7
Exclusive status
YAMAHA ID
When N is received N=0~F, whichever is received.
When N is transmitted N always=0.
Model ID of XG
Address High
Address Mid
Address Low
Data
End of Exclusive
When the XG System On message is received, the MIDI system will be reset
to its default settings.
The message requires approximately 50ms to execute, so sufficient time should
be allowed before the next message is sent.
2.1.4.2 XG System Data parameter change
See Tables 1-1, 1-2.
2.1.4.3 Multi Effect1 Data parameter change
The volume for all channels will be changed.
*Hexadecimal representation of 0sssss ss. (Same below)
126
When the General MIDI mode ON message is received, the MIDI system will
be reset to its default settings.
This message requires approximately 50ms to execute, so sufficient time
should be allowed before the next message is sent.
See Tables 1-1, 1-3.
2.1.4.4 Multi Part Data parameter change
See Tables 1-1, 1-4.
2.1.4.5 Drum Setup Data parameter change
See Tables 1-1, 1-5.
If operation is in XG mode, this message reinitializes all drum setup parameters.
The drum setup will not be reset if any changes are made from the CVP 79A/69/69A/
59S front panel.
○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
2.1.5 Other Parameter Changes
2.2.1.1 XG System Data bulk dump
2.1.5.1 Master Tuning
See Tables 1-1, 1-2.
11110000
01000011
0001nnnn
F0
43
1n
00100111
00000001
00000000
00000000
0mmmmmmm
0lllllll
0ccccccc
11110111
27
30
00
00
mm
ll
cc
F7
Exclusive status
YAMAHA ID
When n is received n=0~F, whichever is received.
When n is transmitted n always=0.
Model ID
Sub ID
Master Tune MSB
Master Tune LSB
End of Exclusive
Changes tuning of all channels.
2.2.1.2 Multi Effect1 Data bulk dump
See Tables 1-1, 1-3.
2.2.1.3 Drums Setup Data bulk dump
See Tables 1-1, 1-5.
2.3 Parameter Request
The CVP 79A/69/69A/59S models support the following request for
parameters covered by Parameter Change specifications.
11110000
01000011
0011nnnn
F0
43
3n
01001100
0aaaaaaa
0aaaaaaa
0aaaaaaa
11110111
4C
aaaaaaa
aaaaaaa
aaaaaaa
F7
2.1.5.2 Channel Detune
11110000
01000011
0001nnnn
00111001
00010001
0000nnnn
01000011
0vvvvvvv
11110111
F0
43
73
39
11
0n
43
vv
F7
Exclusive status
YAMAHA ID
Clavinova ID
CVP-79A/69/69A/59S ID
Sub ID
n = MIDI Channel
Dual Detune
Value vv: $00 - $40 - $7F (-64 - 0 - +63)
End of Exclusive
The Channel Detune message only affects the specified channel.
2.1.5.3 Volume and Expression Realtime Control Off
11110000
01000011
0001nnnn
00111001
00010001
0000nnnn
01000101
0vvvvvvv
11110111
F0
43
73
39
11
0n
45
vv
F7
Exclusive status
YAMAHA ID
Clavinova ID
CVP-79A/69/69A/59S ID
Sub ID
n = MIDI Channel
Volume and Expression Realtime Control Off
Value vv: $00:Off $7F:On
End of Exclusive
When “On” is received subsequent volume and expression changes are only
valid during key on. Normal operation resumes when “Off” is received.
Exclusive status
YAMAHA ID
When n is received n=0~F, whichever is received.
When n is transmitted n always=0.
Model ID of XG
Address High
Address Mid
Address Low
End of Exclusive
If the parameter’s data size is 2 or 4. The Parameter Request address for that
parameter is the first byte of the bulk.
2.4 Dump Request
The CVP 79A/69/69A/59S models support the following request for data
covered by bulk dump.
11110000
01000011
0010nnnn
F0
43
2n
01001100
0aaaaaaa
0aaaaaaa
0aaaaaaa
11110111
4C
aaaaaaa
aaaaaaa
aaaaaaa
F7
Exclusive status
YAMAHA ID
When n is received n=0~F, whichever is received.
When n is transmitted n always=0.
Model ID of XG
Address High
Address Mid
Address Low
End of Exclusive
For more information on the “Address” field, refer to the attached table.
In the attached tables “TOTAL SIZE” partitions a data series into single bulk
dumps. The “address” is the first byte of the bulk data.
2.2 Bulk Dump
The CVP 79A/69/69A/59S models support the following parameters.
[XG NATIVE ]
1) XG System Data
2) Multi Effect1 Data
3) Drums Setup Data
3.1 Active Sensing
a) Transmission
Transmitted approximately once every 200msec.
2.2.1 XG Native Bulk Data
11110000
01000011
0000nnnn
F0
43
0n
01001100
0bbbbbbb
0bbbbbbb
0aaaaaaa
0aaaaaaa
0aaaaaaa
00000000
|
|
0ccccccc
11110111
4C
bbbbbbb
bbbbbbb
aaaaaaa
aaaaaaa
aaaaaaa
00
|
|
ccccccc
F7
3. Realtime Messages
Exclusive status
YAMAHA ID
When n is received n=0~F, whichever is received.
When n is transmitted n always=0.
Model ID of XG
ByteCount
ByteCount
Address High
Address Mid
Address Low
Data
3.2 MIDI Clock
Check sum
End of Exclusive
3.3 Start/Stop
For information about “Address” and “Byte Count” fields, refer to attached
tables.
In the attached tables “TOTAL SIZE” partitions a data series into single bulk
dumps. The “address” is the first byte of the bulk data.
The checksum value is set such that the sum of Byte Count, Address, Data, and
Checksum has value zero in its seven least significant bits.
If too much bulk data is received at a time there is a chance of error. The total
data for a bulk dump should not exceed 512 bytes, it is recommended that data
be kept under 512 bytes with an interval time of 120msec or more between 512
byte bulk.
b) Reception
If no MIDI data is received within 400ms following receipt of FE, the unit
executes processing equivalent to ALL SOUND OFF, ALL NOTES OFF, and
RESET ALL CONTROLLERS, then clears any remaining FEs.
a) Transmission
Transmitted as 1/96 clocks.
b) Reception
If the [MIDI 1] clock function is set to the External mode it will receive a
resolution of 1/96 clocks.
If the [MIDI 2] function Start/Stop filter is ON transmission and reception are
disabled.
a) Transmission
All rhythm start and stop signals are transmitted.
b) Reception
When the relative message is received, the rhythm or song will start or stop.
127
MIDI Data Format / MIDI-Datenformat / Format des donées MIDI / Formato de datos MIDI
<Table 1-1>
Parameter Change
Address
(H) (M) (L)
CVP MIDI
00
00
00
SYSTEM
00
00 7D
00
00
7E
00
00
7F
EFFECT 1
02
01
00
DRUM
30
18
00
31
18
00
Parameter Base Address
Model ID = 4C
Description
System
Drum Setup Reset
XG System On
Reset All Parameters
Effect1(Reverb,Chorus,Variation )
Drum Setup 1
Drum Setup 2
Address
3n 0B 00
3n 0C 00
:
3n 5B 00
m
Note: The CVP 79A/69/69A/59S contain 3 drum setups (1 Preset Drum &
Drum Setup 1, 2). Preset Drum being the preset drum setup, its
parameters cannot be rewritten.
Parameter
note number 13
note number 14
:
note number 91
<Table 1-2>
MIDI Parameter Change table ( SYSTEM )
Address
(H)
00 00 00
01
02
03
04
06
07
7D
7E
7F
TOTAL SIZE
Size
(H)
4
Data
(H)
0000 - 07FF
1
1
1
00 - 7F
28 - 58
—
n
00
00
Parameter
Description
MASTER TUNE
-102.4 - +102.3[cent]
1st bit3-0→bit15-12
2nd bit3-0→bit11-8
3rd bit3-0→bit7-4
4th bit3-0→bit3-0
0 - 127
-24 - +24[semitones]
MASTER VOLUME
TRANSPOSE
—
DRUM SETUP RESET
XG SYSTEM ON
RESET ALL PARAMETERS
Default value
(H)
00 04 00 00
-400
7F
40
n=Drum setup number
00=XG sytem ON
00=ON (receive only)
07
<Table 1-3>
MIDI Parameter Change table ( EFFECT 1)
Refer to the “Effect MIDI Map” for a complete list of Reverb, Chorus and Variation type numbers.
Refer to the “Effect Parameter List” for a detailed description of each parameter.
128
Address
(H)
02 01 00
Size
(H)
2
Data
(H)
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
01-7F
Parameter
Description
REVERB TYPE MSB
REVERB TYPE LSB
REVERB PARAMETER 1
REVERB PARAMETER 2
REVERB PARAMETER 3
REVERB PARAMETER 4
REVERB PARAMETER 5
REVERB PARAMETER 6
REVERB PARAMETER 7
REVERB PARAMETER 8
REVERB PARAMETER 9
REVERB PARAMETER 10
REVERB RETURN
REVERB PAN
Refer to Effect MIDI Map
00 : basic type
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
-∞dB...0dB...+6dB(0...64...127)
L63...C...R63(1...64...127)
Default value
(H)
01(=HALL1)
00
Depends on reverb type
Depends on reverb type
Depends on reverb type
Depends on reverb type
Depends on reverb type
Depends on reverb type
Depends on reverb type
Depends on reverb type
Depends on reverb type
Depends on reverb type
40
40
02
03
04
05
06
07
08
09
0A
0B
0C
0D
TOTAL SIZE
1
1
1
1
1
1
1
1
1
1
1
1
0E
02 01 10
11
12
13
14
15
TOTAL SIZE
1
1
1
1
1
1
6
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
REVERB PARAMETER 11
REVERB PARAMETER 12
REVERB PARAMETER 13
REVERB PARAMETER 14
REVERB PARAMETER 15
REVERB PARAMETER 16
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Depends on reverb type
Depends on reverb type
Depends on reverb type
Depends on reverb type
Depends on reverb type
Depends on reverb type
02 01 20
2
22
23
24
25
26
27
28
29
2A
2B
2C
2D
2E
TOTAL SIZE
1
1
1
1
1
1
1
1
1
1
1
1
1
0F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
01-7F
00-7F
CHORUS TYPE MSB
CHORUS TYPE LSB
CHORUS PARAMETER 1
CHORUS PARAMETER 2
CHORUS PARAMETER 3
CHORUS PARAMETER 4
CHORUS PARAMETER 5
CHORUS PARAMETER 6
CHORUS PARAMETER 7
CHORUS PARAMETER 8
CHORUS PARAMETER 9
CHORUS PARAMETER 10
CHORUS RETURN
CHORUS PAN
SEND CHORUS TO REVERB
Refer to Effect MIDI Map
00 : basic type
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
-∞dB...0dB...+6dB(0...64...127)
L63...C...R63(1...64...127)
-∞dB...0dB...+6dB(0...64...127)
41(=CHORUS1)
00
Depends on chorus type
Depends on chorus type
Depends on chorus type
Depends on chorus type
Depends on chorus type
Depends on chorus type
Depends on chorus type
Depends on chorus type
Depends on chorus type
Depends on chorus type
40
40
00
02 01 30
31
32
33
34
35
TOTAL SIZE
1
1
1
1
1
1
6
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
CHORUS PARAMETER 11
CHORUS PARAMETER 12
CHORUS PARAMETER 13
CHORUS PARAMETER 14
CHORUS PARAMETER 15
CHORUS PARAMETER 16
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Depends on chorus type
Depends on chorus type
Depends on chorus type
Depends on chorus type
Depends on chorus type
Depends on chorus type
02 01 40
2
42
2
00-7F
00-7F
00-7F
00-7F
VARIATION TYPE MSB
VARIATION TYPE LSB
VARIATION PARAMETER 1 MSB
VARIATION PARAMETER 1 LSB
Refer to Effect MIDI Map
00 : basic type
Refer to Effect Parameter List
Refer to Effect Parameter List
05(=DELAY L,C,R)
00
Depends on variation type
Depends on Variation type
○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
44
2
46
2
48
2
4A
2
4C
2
4E
2
50
2
52
2
54
2
56
57
58
59
5A
5B
1
1
1
1
1
1
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
01-7F
00-7F
00-7F
00-01
00-7F
5C
5D
5E
5F
60
TOTAL SIZE
1
1
1
1
1
21
—
—
—
—
—
02 01 70
71
72
73
74
75
TOTAL SIZE
1
1
1
1
1
1
6
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
VARIATION PARAMETER 2 MSB
VARIATION PARAMETER 2 LSB
VARIATION PARAMETER 3 MSB
VARIATION PARAMETER 3 LSB
VARIATION PARAMETER 4 MSB
VARIATION PARAMETER 4 LSB
VARIATION PARAMETER 5 MSB
VARIATION PARAMETER 5 LSB
VARIATION PARAMETER 5 MSB
VARIATION PARAMETER 6 LSB
VARIATION PARAMETER 7 MSB
VARIATION PARAMETER 7 LSB
VARIATION PARAMETER 8 MSB
VARIATION PARAMETER 8 LSB
VARIATION PARAMETER 9 MSB
VARIATION PARAMETER 9 LSB
VARIATION PARAMETER 10 MSB
VARIATION PARAMETER 10 LSB
VARIATION RETURN
VARIATION PAN
SEND VARIATION TO REVERB
SEND VARIATION TO CHORUS
VARIATION CONNECTION
VARIATION PART
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
-∞dB...0dB...+6dB(0...64...127)
L63...C...R63(1...64...127)
-∞dB...0dB...+6dB(0...64...127)
-∞dB...0dB...+6dB(0...64...127)
0:INSERTION,1:SYSTEM
OFF(127)
Part 1-16 (0-15)
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
Depends on Variation type
40
40
00
00
00
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Refer to Effect Parameter List
Depends on variation type
Depends on variation type
Depends on variation type
Depends on variation type
Depends on variation type
Depends on variation type
Default value
(H)
00 (Part other than 10)
01 (Part10)
—
—
—
—
—
VARIATION PARAMETER 11
VARIATION PARAMETER 12
VARIATION PARAMETER 13
VARIATION PARAMETER 14
VARIATION PARAMETER 15
VARIATION PARAMETER 16
* “VARIATION” refers to the EFFECT on the panel.
<Table 1-4>
MIDI Parameter Change table ( MULTI PART )
Address
(H)
08 nn 07
Size
(H)
1
Data
(H)
00 - 01
Parameter
Description
PART MODE
0:NORMAL
1:Preset Drum
2 - 3:Drum Setup 1, 2
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
nn
1
1
1
1
1
1
1
1
1
1
1
1
1
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
DRY LEVEL
SCALE TUNING C
SCALE TUNING C#
SCALE TUNING D
SCALE TUNING D#
SCALE TUNING E
SCALE TUNING F
SCALE TUNING F#
SCALE TUNING G
SCALE TUNING G#
SCALE TUNING A
SCALE TUNING A#
SCALE TUNING B
0 - 127
-64 - +63[cent]
-64 - +63[cent]
-64 - +63[cent]
-64 - +63[cent]
-64 - +63[cent]
-64 - +63[cent]
-64 - +63[cent]
-64 - +63[cent]
-64 - +63[cent]
-64 - +63[cent]
-64 - +63[cent]
-64 - +63[cent]
7F
40
40
40
40
40
40
40
40
40
40
40
40
11
41
42
43
44
45
46
47
48
49
4A
4B
4C
nn = PartNumber
For DRUM PART, the SCALE TUNING parameter is ineffective.
<Table 1-5>
MIDI Parameter Change table ( DRUM SETUP )
Address
(H)
3n rr 00
3n rr 01
3n rr 02
3n rr 03
3n rr 04
3n rr 05
3n rr 06
3n rr 07
3n rr 08
3n rr 09
3n rr 0A
3n rr 0B
3n rr 0C
3n rr 0D
3n rr 0E
3n rr 0F
TOTAL SIZE
Size
(H)
1
1
1
1
1
Data
(H)
00 - 7F
00 - 7F
00 - 7F
—
00 - 7F
Parameter
Description
PITCH COARSE
PITCH FINE
LEVEL
—
PAN
-64 - +63
-64 - +63[cent]
0 - 127
Default value
(H)
40
40
Depends on note
1
1
1
1
1
1
1
1
1
1
1
10
00 - 7F
00 - 7F
00 - 7F
—
—
—
00 - 7F
00 - 7F
00 - 7F
00 - 7F
00 - 7F
REVERB SEND
CHORUS SEND
VARIATION SEND
—
—
—
FILTER CUTOFF FREQUENCY
FILTER RESONANCE
EG ATTACK
EG DECAY1
EG DECAY2
0:random
L63...C...R63(1...64...127)
0 - 127
0 - 127
0 - 127
Depends on note
Depends on note
7F
-64 - 63
-64 - 63
-64 - 63
-64 - 63
-64 - 63
40
40
40
40
40
Depends on note
[Note]
n:
Drum Setup number (0 to 1)
rr:
Note number (0D to 54)
Receipt of “XG System On” or “GM System On” message generates reinitialization of all DRUM SETUP parameters.
“Drum Setup Reset” message can be used to reinitialize drum setup parameters.
129
MIDI Data Format / MIDI-Datenformat / Format des donées MIDI / Formato de datos MIDI
● Effect MIDI Map
REVERB TYPE
TYPE MSB
DEC HEX
000
0
001
1
002
2
003
3
004
4
005
5
:
:
015
F
016
10
017
11
018
12
019
13
020
14
:
:
127
7F
TYPE LSB
00
No Effect
Hall1*
Room4
Stage3
Plate2
No Effect
:
No Effect
WhiteRoom*
Tunnel*
Canyon* (79)
Basement*
No Effect
:
No Effect
01
<——
Hall3
Room5
Stage4
<——
<——
02
<——
<——
Room6
<——
<——
<——
03~07
<——
<——
<——
<——
<——
<——
08
<——
Hall2*
Room1*
Stage1*
Plate1*
<——
09
<——
Hall4
Room2*
Stage2*
Plate3
<——
0a
<——
Hall5
Room3*
<——
<——
<——
0b
<——
<——
Room7
<——
<——
<——
0c
<——
<——
<——
<——
<——
<——
0d~
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<—— .......... Same as Basic Effect (LSB=0)
* ............. Used in Panel REVERB SW
(79) ...... CVP-79A only
CHORUS TYPE
TYPE MSB
DEC HEX
000
0
001
1
:
:
064
40
065
41
066
42
067
43
068
44
069
45
:
:
071
47
072
48
073
49
:
:
127
7F
TYPE LSB
00
No Effect
No Effect
:
No Effect
Chorus4
Celeste
Flanger2
Symphonic (79)
No Effect
:
No Effect
Phaser (79)
No Effect
:
No Effect
01
<——
<——
02
<——
<——
03~07
<——
<——
08
<——
<——
09
<——
<——
0a
<——
<——
0b
<——
<——
0c
<——
<——
0d~
<——
<——
<——
Chorus2
Celeste2
Flanger3
<——
<——
<——
Chorus3
Celeste3
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Celeste4
Flanger1
<——
<——
<——
<——
Celeste5
Flanger4
<——
<——
<——
<——
Chorus1
Flanger5
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<—— .......... Same as Basic Effect (LSB=0)
(79) ....... CVP-79A only
VARIATION TYPE
TYPE MSB
DEC HEX
000
0
001
1
002
2
003
3
004
4
005
5
006
6
007
7
008
8
009
9
010
A
011
B
012
C
:
:
019
13
020
14
021
15
:
:
063
3F
064
40
065
41
066
42
067
43
068
44
069
45
070
46
071
47
072
48
073
49
074
4A
075
4B
076
4C
077
4D
078
4E
079
4F
080
50
081
51
082
52
083
53
084
54
085
55
:
:
127
7F
TYPE LSB
00
No Effect
Hall1
Room4
Stage3
Plate2
Delay L, C, R*
Delay L, R*
Echo*
CrossDelay*
EarlyRef.1
GateReverb
ReverseGate
No Effect
:
No Effect
Karaoke1
No Effect
:
No Effect
Thru
Chorus4
Celeste*
Flanger2
Symphonic2
RotarySp.Fast*
Tremolo*
AutoPan2
Phaser*
Distortion
OverDrive
AmpSim.1
3BandEQ2
2BandEQ
AutoWah2
No Effect or Thru
Detune* (79)
No Effect or Thru
TouchWah* (79)
Compressor* (79)
NoizeGate (79)
No Effect or Thru
01
<——
Hall3
Room5
Stage4
<——
<——
<——
<——
<——
EarlyRef.2
<——
<——
<——
02
<——
<——
Room6
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
03~07
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
08
<——
Hall2
Room1
Stage1
Plate1
Delay2
<——
<——
<——
<——
<——
<——
<——
<——
Hall4
Room2
Stage2
Plate3
Delay3
<——
<——
<——
<——
<——
<——
<——
0a
<——
Hall5
Room3
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
0b
<——
<——
Room7
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
0c
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
0d~
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Karaoke2
<——
<——
Karaoke3
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Chorus2*
Celeste2
Flanger3
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Wah+Dist (79)
<——
<——
<——
<——
<——
Chorus3*
Celeste3
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Celeste4
Flanger1*
Symphonic*
RotarySp.3
Tremolo2
AutoPan*
<——
<——
<——
AmpSim.2
BoostHL*
<——
AutoWah*
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Celeste5
Flanger4
<——
<——
<——
RotarySp.Slow*
<——
<——
<——
AmpSim.3
3BandEQ3
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Chorus1*
Flanger5
<——
RotarySp.4
Tremolo3
AutoPan3
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
Celeste6
<——
<——
RotarySp.5
Tremolo4
AutoPan4
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
AutoPan5
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<——
<—— .......... Same as Basic Effect (LSB=0)
130
09
* ............. Used in Panel EFFECT SW
(79) ...... CVP-79A only
○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
● Effect Parameter List
BASIC EFFECT TYPE
No. Parameter
Data Range
CVP-79A
MIDI Value
CVP-69/69A/59S
No. Parameter
Data Range
CVP-79A
MIDI Value
CVP-69/69A/59S
TREMOLO
CHORUS, CELESTE
1
2
3
4
5
6
7
8
9
10
LFO Frequency
LFO PM Depth
Feedback Level
Delay Offset
—
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
0.00~39.7Hz
0~127
-63~+63
0~127
—
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W~D=W~D<W63
0-127
0-63
1-127
0-127
—
4-40 32Hz~2.0kHz
52-76
28-58
52-76
1-127
0-127
0-127
1-127
0-127
—
8-40
52-76
28-58
52-76
1-127
1
2
3
4
5
6
7
8
9
10
LFO Frequency
AM Depth
PM Depth
—
—
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
—
0.00~39.7Hz
0~127
0~127
—
—
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
—
0-127
0-127
0-127
—
—
4-40 32Hz~2.0kHz
52-76
28-58
52-76
—
0-127
0-127
0-127
—
—
8-40
52-76
28-58
52-76
—
11
12
13
14
15
16
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
LFO AM Depth
Input Mode
—
100Hz~10.0kHz
-12~+12dB
1.0~12.0
0~127
mono/stereo
—
14-54
52-76
10-120
0-127
—
—
—
—
—
—
0-1
—
11
12
13
14
15
16
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
LFO Phase Difference
Input Mode
—
100Hz~10.0kHz
-12~+12dB
1.0~12.0
-180~+180deg
mono/stereo
—
14-54
52-76
10-120
4-124
—
—
—
—
—
resolution = 3deg.
0-1
—
0-127
0-127
0-127
0-5
0-127
0-127
0-127
0-5
—
4-40 32Hz~2.0kHz
52-76
28-58
52-76
—
—
8-40
52-76
28-58
52-76
—
AUTO PAN
FLANGER
1
2
3
4
5
6
7
8
9
10
LFO Frequency
LFO Depth
Feedback Level
Delay Offset
—
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
0.00~39.7Hz
0~127
-63~+63
0~63
—
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W~D=W~D<W63
0-127
0-127
1-127
0-63
—
4-40 32Hz~2.0kHz
52-76
28-58
52-76
1-127
0-127
0-127
1-127
0-63
—
8-40
52-76
28-58
52-76
1-127
11
12
13
14
15
16
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
LFO Phase Difference
—
—
100Hz~10.0kHz
-12~+12dB
1.0~12.0
-180~+180deg
—
—
14-54
52-76
10-120
4-124
—
—
—
—
—
resoulusion = 3deg.
—
—
1
2
3
4
LFO Frequency
L/R Depth
F/R Depth
PAN Direction
5
6
7
8
9
10
—
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
—
0.00~39.7Hz
0~127
0~127
L<->R,L->R,L<-R,
Lturn,Rturn,L/R
—
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
—
11
12
13
14
15
16
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
—
—
—
100Hz~10.0kHz
-12~+12dB
1.0~12.0
—
—
—
14-54
52-76
10-120
—
—
—
—
—
—
—
—
—
0.00~39.7Hz
0~127
0~127
-63~+63
—
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W~D=W~D<W63
0-127
0-127
0-127
1-127
—
4-40 32Hz~2.0kHz
52-76
28-58
52-76
1-127
0-127
0-127
0-127
1-127
—
8-40
52-76
28-58
52-76
1-127
11 Stage
3~10
“3-10 (4,6,8)”
12
13
14
15
16
Mono/Stereo
-180~+180deg.
—
—
—
0-1
—
—
—
—
3-10 (6~10 (phaser1)
/ 3~5 (phaser2))
0-1
4-124
—
—
—
SYMPHONIC
1
2
3
4
5
6
7
8
9
10
LFO Frequency
LFO Depth
Delay Offset
—
—
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
0.00~39.7Hz
0~127
0~127
—
—
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W~D=W~D<W63
0-127
0-127
0-127
—
—
4-40 32Hz~2.0kHz
52-76
28-58
52-76
1-127
0-127
0-127
0-127
—
—
8-40
52-76
28-58
52-76
1-127
11
12
13
14
15
16
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
—
—
—
100Hz~10.0kHz
-12~+12dB
1.0~12.0
—
—
—
14-54
52-76
10-120
—
—
—
—
—
—
—
—
—
ROTARY SPEAKER
1
2
3
4
5
6
7
8
9
10
LFO Frequency
LFO Depth
—
—
—
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
0.00~39.7Hz
0~127
—
—
—
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W~D=W~D<W63
0-127
0-127
—
—
—
4-40 32Hz~2.0kHz
52-76
28-58
52-76
1-127
0-127
0-127
—
—
—
8-40
52-76
28-58
52-76
1-127
11
12
13
14
15
16
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
—
—
—
100Hz~10.0kHz
-12~+12dB
1.0~12.0
—
—
—
14-54
52-76
10-120
—
—
—
—
—
—
—
—
—
PHASER
1
2
3
4
5
6
7
8
9
10
LFO Frequency
LFO Depth
Phase Shift Offset
Feedback Level
—
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
Diffusion
LFO Phase Difference
—
—
—
DISTORTION, OVERDRIVE
1
2
3
4
5
6
7
Drive
EQ Low Frequency
EQ Low Gain
LPF Cutoff
Output Level
—
EQ Mid Frequency
0-127
8-40
52-76
34-60
0-127
—
28-54
8 EQ Mid Gain
9 EQ Mid Width
10 Dry/Wet
0-127
4-40 32Hz~2.0kHz
52-76
34-60
0-127
—
14-54
100Hz~10.0kHz
-12~+12dB
52-76
1.0~12.0
10-120
D63>W~D=W~D<W63 1-127
11
12
13
14
15
16
0~127
—
—
—
—
—
0-127
—
—
—
—
—
Edge (Clip Curve)
—
—
—
—
—
0~127
50Hz~2.0kHz
-12~+12dB
1.0k~Thru
0~127
—
500Hz~10.0kHz
—
—
—
—
—
—
52-76
10-120
1-127
131
MIDI Data Format / MIDI-Datenformat / Format des donées MIDI / Formato de datos MIDI
No. Parameter
Data Range
CVP-79A
MIDI Value
CVP-69/69A/59S
GUITAR AMP SIMULATOR
No. Parameter
Data Range
CVP-79A
MIDI Value
CVP-69/69A/59S
HALL, ROOM, STAGE, PLATE
1
2
3
4
5
6
7
8
9
10
Drive
AMP Type
LPF Cutoff
Output Level
—
—
—
—
—
Dry/Wet
0~127
Off,Stack,Combo,Tube
1.0k~Thru
0~127
—
—
—
—
—
D63>W~D=W~D<W63
0-127
0-3
34-60
0-127
—
—
—
—
—
1-127
0-127
0-3
34-60
0-127
—
—
—
—
—
1-127
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Edge (Clip Curve)
—
—
—
—
—
0~127
—
—
—
—
—
—
—
—
—
—
—
0-127
—
—
—
—
—
-12~+12dB
500Hz~10.0kHz
52-76
28-54
Reverb Time
Diffusion
Initial Delay
HPF Cutoff
LPF Cutoff
—
—
—
—
Dry/Wet
0.3~30.0s
0~10
0~63
Thru~8.0kHz
1.0k~Thru
—
—
—
—
D63>W~D=W~D<W63
0-69
0-10
0-63
0-52
34-60
—
—
—
—
1-127
0-69
0-10
0-63
0-52
34-60
—
—
—
—
1-127
11 Rev Delay
12 Density
0~63
0~3
0-63
0-3
13
14
15
16
E63>R~E=R~E<R63
0.1~1.0
-63~+63
—
0-63
“0-4 *REV (0-4),
VAR (0-3)”
1-127
1-10
—
—
1-127
—
1-127
—
Er/Rev Balance
High Damp
Feedback Level
—
MONO EQ (3BAND)
1 EQ Low Gain
2 EQ Mid Frequency
3
4
5
6
7
8
9
10
EQ Mid Gain
EQ Mid Width
EQ High Gain
EQ Low Frequency
EQ High Frequency
—
—
—
-12~+12dB
1.0~12.0
-12~+12dB
50Hz~2.0kHz
500Hz~16.0kHz
—
—
—
52-76
14-54
100Hz~10.0kHz
52-76
10-120
52-76
4-40 32Hz~2.0kHz
28-58
—
—
—
11
12
13
14
15
16
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
52-76
10-120
52-76
8-40
28-58
—
—
—
1
2
3
4
5
6
7
8
9
10
Lch Delay
Rch Delay
Cch Delay
Feedback Delay
Feedback Level
Cch Level
High Damp
—
—
Dry/Wet
0.1~715.0ms
0.1~715.0ms
0.1~715.0ms
0.1~715.0ms
-63~+63
0~127
0.1~1.0
—
—
D63>W~D=W~D<W63
1-7150
1-7150
1-7150
1-7150
1-127
0-127
1-10
—
—
1-127
1-7150
1-7150
1-7150
1-7150
1-127
0-127
1-10
—
—
1-127
11
12
13
14
15
16
HPF Cutoff
LPF Cutoff
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Thru~8.0kHz
1.0k~Thru
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
0-52
34-60
—
—
—
—
—
—
8-40
52-76
28-58
52-76
STEREO EQ (2BAND)
DELAY L, R
1
2
3
4
5
6
7
8
9
10
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
—
—
—
—
—
—
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
—
—
—
—
—
—
4-40 32Hz~2.0kHz
52-76
28-58
52-76
—
—
—
—
—
—
8-40
52-76
28-58
52-76
—
—
—
—
—
—
1
2
3
4
5
6
7
8
9
10
Lch Delay
Rch Delay
Feedback Delay 1
Feedback Delay 2
Feedback Level
High Damp
—
—
—
Dry/Wet
0.1~715.0ms
0.1~715.0ms
0.1~715.0ms
0.1~715.0ms
-63~+63
0.1~1.0
—
—
—
D63>W~D=W~D<W63
1-7150
1-7150
1-7150
1-7150
1-127
1-10
—
—
—
1-127
1-7150
1-7150
1-7150
1-7150
1-127
1-10
—
—
—
1-127
11
12
13
14
15
16
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
—
—
—
100Hz~10.0kHz
-12~+12dB
1.0~12.0
—
—
—
14-54
52-76
10-120
—
—
—
—
—
—
—
—
—
11
12
13
14
15
16
HPF Cutoff
LPF Cutoff
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Thru~8.0kHz
1.0k~Thru
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
0-52
34-60
—
—
—
—
—
—
8-40
52-76
28-58
52-76
AUTO WAH
132
DELAY L, C, R
ECHO
1
2
3
4
5
6
7
8
9
10
LFO Frequency
LFO Depth
Cutoff Frequency Offset
Resonance
—
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
0.00~39.7Hz
0~127
0~127
1.0~12.0
—
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W~D=W~D<W63
0-127
0-127
0-127
10-120
—
4-40 32Hz~2.0kHz
52-76
28-58
52-76
1-127
0-127
0-127
0-127
10-120
—
8-40
52-76
28-58
52-76
1-127
1
2
3
4
5
6
7
8
9
10
Lch Delay1
Lch Feedback Level
Rch Delay1
Rch Feedback Level
High Damp
Lch Delay2
Rch Delay2
Delay2 Level
—
Dry/Wet
0.1~355.0ms
-63~+63
0.1~355.0ms
-63~+63
0.1~1.0
0.1~355.0ms
0.1~355.0ms
0~127
—
D63>W~D=W~D<W63
1-3550
1-127
1-3550
1-127
1-10
1-3550
1-3550
0-127
—
1-127
1-3550
1-127
1-3550
1-127
1-10
1-3550
1-3550
0-127
—
1-127
11
12
13
14
15
16
Drive
—
—
—
—
—
0~127
—
—
—
—
—
0-127
—
—
—
—
—
—
—
—
—
—
—
11
12
13
14
15
16
HPF Cutoff
LPF Cutoff
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Thru~8.0kHz
1.0k~Thru
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
0-52
34-60
—
—
—
—
—
—
8-40
52-76
28-58
52-76
○
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
No. Parameter
Data Range
CVP-79A
MIDI Value
CVP-69/69A/59S
CROSS DELAY
1
2
3
4
5
6
7
8
9
10
L->R Delay
R->L Delay
Feedback Level
Input Select
High Damp
—
—
—
—
Dry/Wet
0.1~355.0ms
0.1~355.0ms
-63~+63
L,R,L&R
0.1~1.0
—
—
—
—
D63>W~D=W~D<W63
1-3550
1-3550
1-127
0-2
1-10
—
—
—
—
1-127
1-3550
1-3550
1-127
0-2
1-10
—
—
—
—
1-127
11
12
13
14
15
16
HPF Cutoff
LPF Cutoff
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Thru~8.0kHz
1.0k~Thru
50Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
0-52
34-60
—
—
—
—
—
—
8-40
52-76
28-58
52-76
EARLY REF
1
2
3
4
5
6
7
8
9
10
Type
Room Size
Diffusion
Initial Delay
Feedback Level
HPF Cutoff
LPF Cutoff
—
—
Dry/Wet
S-H, L-H, Rdm, Rvs, Plt, Spr
0.1~7.0
0~10
0~63
-63~+63
Thru~8.0kHz
1.0k~Thru
—
—
D63>W~D=W~D<W63
0-5
0-44
0-10
0-63
1-127
0-52
34-60
—
—
1-127
0-5
0-44
0-10
0-63
1-127
0-52
34-60
—
—
1-127
11
12
13
14
15
16
Liveness
Density
High Damp
—
—
—
0~10
0~3
0.1~1.0
—
—
—
0-10
0-3
1-10
—
—
—
0-10
0-3
1-10
—
—
—
GATE REVERB, REVERSE GATE
1
2
3
4
5
6
7
8
9
10
Type
Room Size
Diffusion
Initial Delay
Feedback Level
HPF Cutoff
LPF Cutoff
—
—
Dry/Wet
TypeA,TypeB
0.1~7.0
0~10
0~63
-63~+63
Thru~8.0kHz
1.0k~Thru
—
—
D63>W~D=W~D<W63
0-1
0-44
0-10
0-63
1-127
0-52
34-60
—
—
1-127
0-1
0-44
0-10
0-63
1-127
0-52
34-60
—
—
1-127
11
12
13
14
15
16
Liveness
Density
High Damp
—
—
—
0~10
0~3
0.1~1.0
—
—
—
0-10
0-3
1-10
—
—
—
0-10
0-3
1-10
—
—
—
133
MIDI Data Format / MIDI-Datenformat / Format des donées MIDI / Formato de datos MIDI
OPTION EFFECT TYPE
No. Parameter
Data Range
CVP-79A
MIDI Value
CVP-69/69A/59S
No. Parameter
Data Range
CVP-79A
MIDI Value
CVP-69/69A/59S
NOISE GATE (CVP-79A only)
PITCH CHANGE (CVP-79A only)
1
2
3
4
5
6
7
8
9
10
Pitch
Initial Delay
Fine 1
Fine 2
Feedback Gain
—
—
—
—
Dry/Wet
-24~+24
0~127
-50~+50
-50~+50
-99~+99%
—
—
—
—
D63>W~D=W~D<W63
40-88
0-127
14-114
14-114
1-127
—
—
—
—
1-127
—
—
—
—
—
—
—
—
—
—
1
2
3
4
5
6
7
8
9
10
Attack
Release
Threshold
Output Level
—
—
—
—
—
—
1~40ms
10~680ms
-72~-30dB
0~127
—
—
—
—
—
—
0-19
0-15
55-97
0-127
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
11
12
13
14
15
16
Pan 1
Output Level 1
Pan 2
Output Level 2
—
—
L63~R63
0~127
L63~R63
0~127
—
—
1-127
0-127
1-127
0-127
—
—
—
—
—
—
—
—
11
12
13
14
15
16
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
WHITE ROOM, TUNNEL, CANYON (CVP-79A only), BASEMENT
TOUCH WAH, WAH+DIST (CVP-79A only)
1
2
3
4
5
6
7
8
9
10
Sensitive
Cutoff Frequency Offset
Resonance
—
—
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
0~127
0~127
1.0~12.0
—
—
32Hz~2.0kHz
-12~+12dB
500Hz~16.0kHz
-12~+12dB
D63>W~D=W~D<W63
0-127
0-127
10-120
—
—
4-40
52-76
28-58
52-76
1-127
—
—
—
—
—
—
—
—
—
—
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Drive
—
—
—
—
—
0~127
—
—
—
—
—
0-127
—
—
—
—
—
—
—
—
—
—
—
Reverb Time
Diffusion
Initial Delay
HPF Cutoff
LPF Cutoff
Width
Heigt
Depth
Wall Vary
Dry/Wet
0.3~30.0s
0~10
0~63
Thru~8.0kHz
1.0k~Thru
0.5~10.2m
0.5~20.2m
0.5~30.2m
0~30
D63>W~D=W~D<W63
0-69
0-10
0-63
0-52
34-60
0-37
0-73
0-104
0-30
1-127
0-69
0-10
0-63
0-52
34-60
0-37
0-73
0-104
0-30
1-127
11 Rev Delay
12 Density
0~63
0~3
0-63
0-3
13
14
15
16
E63>R~E=R~E<R63
0.1~1.0
-63~+63
—
0-63
“0-4 *REV (0-4),
VAR (0-3)”
1-127
1-10
—
—
1-127
—
1-127
—
Er/Rev Balance
High Damp
Feedback Level
—
COMPRESSOR (CVP-79A only)
134
1
2
3
4
5
6
7
8
9
10
Attack
Release
Threshold
Ratio
Output Level
—
—
—
—
—
1~40ms
10~680ms
-48~-6dB
1.0~20.0
0~127
—
—
—
—
—
0-19
0-15
79-121
0-7
0-127
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
11
12
13
14
15
16
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
KARAOKE1, 2, 3
1
2
3
4
5
6
7
8
9
10
Delay Time
Feedback Level
HPF Cutoff
LPF Cutoff
—
—
—
—
—
Dry/Wet
0~127
-63~+63
Thru~8.0kHz
1.0k~Thru
—
—
—
—
—
D63>W~D=W~D<W63
0-127
1-127
0-52
34-60
—
—
—
—
—
1-127
0-127
1-127
0-52
34-60
—
—
—
—
—
1-127
11
12
13
14
15
16
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
Specifications / Technische Datan /
Spécifications / Especificationes
CVP-79A
CVP-69
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
CVP-69A
CVP-59S
KEYBOARD
88 KEYS (A-1 — C7)
TONE GENERATOR
AWM (Advanced Wave Memory)
VOICE
Voice Groups: PIANO, E. PIANO, HARPSICHORD, GUITAR, CLAVINOVA TONE/SYNTH, ORGAN, STRINGS/CHOIR,
BRASS, SAX/FLUTE, BASS, DRUMS/PERCUSSIVE (192 voices for CVP-79A, 172 voices for CVP-69/69A/59S)
DUAL, SPLIT, EFFECT
STYLE
Style Groups: POP, 16BEAT, DANCE POP, ROCK, BALLAD, JAZZ, LATIN, LATIN POP, TRADITIONAL, COUNTRY, WALTZ
(100 styles)
DISK/CUSTOM, HARMONY, ONE TOUCH SETTING
AUTO BASS CHORD
INTRO A/FILL TO A, INTRO B/FILL TO B, MAIN A, MAIN B, ENDING, SMALL ABC, ABC ON
METRONOME, TEMPO –/+
START/STOP
TAP, SYNCHRO, START/STOP
KEYBOARD PERCUSSION
8 Drum Kits (72 instruments in each Drum Kit)
REVERB
HALL1, HALL2, ROOM1, ROOM2, ROOM3, STAGE1, STAGE2, PLATE, WHITE ROOM, TUNNEL, CANYON (CVP-79A only),
BASEMENT
SONG
PLAY, RECORD, GUIDE
SONG CONTROL
r REW, f FF, o PAUSE
REGISTRATION
MEMORY, BANK, 1 — 5, ABC FREEZE
LCD & DISPLAY
CONTROLS
240 x 64 dots Liquid Crystal Display, CONTRAST, BEAT, FUNCTION, MIXER, PAGE </>, DISPLAY HOLD, 5 LCD Buttons,
EXIT, Data Dial, –/+
VOLUME
MASTER VOLUME, ABC/SONG VOLUME
DEMO/HELP
25 demonstration tunes, 4 help languages (English, German, French, Japanese)
DISK DRIVE
3.5" 2DD or 2HD Micro Floppy Disk Drive
PEDAL
CONTROLS
RIGHT
DAMPER
CENTER
SOSTENUTO
LEFT
Multi-function: SOFT, START/STOP, HARMONY ON/OFF, REGISTRATION+, INTRO A/FILL TO A, INTRO B/FILL TO B,
ENDING/RIT., BREAK, SOSTENUTO (CVP-59S only)
—
JACKS
PHONES x 2, AUX OUT R and L/L + R, AUX IN R and L/L+R, EXP PEDAL (CVP-79A only)
CONNECTORS
MIDI IN/OUT/THRU
INPUT & OUTPUT
LEVEL/IMPEDANCE
AUX OUT: Output Impedance 600 Ω
AUX IN: Input Impedance 10 kΩ / Input Sensitivity -10dBm
MAIN AMPLIFIERS
120 W (60 W x 2)
120 W (60 W x 2)
120 W (60 W x 2)
60 W (30 W x 2)
SPEAKERS
(16 cm + 5 cm) x 2, 5 cm x 2
(6-5/16" + 2") x 2, 2" x 2
(16 cm + 5 cm) x 2, 5 cm x 2
(6-5/16" + 2") x 2, 2" x 2
(16 cm + 5 cm) x 2, 5 cm x 2
(6-5/16" + 2") x 2, 2" x 2
16 cm x 2, 5 cm x 2
6-5/16" x 2, 2" x 2
Music stand
down
1417 mm x 590 mm x 840 mm
(55-13/16" x 23-1/4" x 33-1/16")
1417 mm x 590 mm x 848 mm
(55-13/16" x 23-1/4" x 33-3/8")
1417 mm x 590 mm x 845 mm
(55-13/16" x 23-1/4" x 33-1/4")
1396 mm x 566 mm x 830 mm
(54-15/16" x 22-5/16" x 32-11/16")
Music stand
up
1417 mm x 590 mm x 1025 mm
(55-13/16" x 23-1/4" x 40-3/8")
1417 mm x 590 mm x 1019 mm
(55-13/16" x 23-1/4" x 40-1/8")
1417 mm x 590 mm x 1025 mm
(55-13/16" x 23-1/4" x 40-3/8")
1396 mm x 566 mm x 1003 mm
(54-15/16" x 22-5/16" x 39-1/2")
68.0 kg (149.9 lbs.)
71.5 kg (157.6 lbs.)
69.0 kg (152.1 lbs.)
65.5 kg (144.4 lbs.)
DIMENSIONS
(W x D x H)
WEIGHT
MIDI IN/OUT
*
*
*
*
Specifications subject to change without notice.
Änderungen ohne Vorankündigung vorbehalten.
Sous toute réserve de modification des caractéristiques sans préavis.
Especificaciones sujetas a cambios sin previo aviso.
135
1
5 x 20 mm screws x 28
Schrauben (5 x 20 mm) x 28
Vis de 5 x 20 mm x 28
Tornillos de 5 x 20 mm x 28
● AC power cord
● Netzkabel
● Cordon d’alimentation
● Cable de alimentación de CA
CVP-79A:
Assembly
CVP-79A:
Zusammenbau
○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○
• We do not recommend attempting to assemble the Clavinova
alone. The job can be easily accomplished, however, with only two
people.
• Wir raten Ihnen davon ab, das Clavinova alleine zusammenzubauen und aufzustellen. Zwei Personen können diese Arbeit jedoch
problemlos ausführen.
• Use only the screws provided or replacements of exactly the specified size. Using screws of the wrong size can result in damage to
the instrument.
• Verwenden Sie ausschließlich die mitgeliefenten Schrauben oder
Ersatzschrauben identischer Größe. Die Verwendung von Schrauben mit abweichenden Maßen kann eine Beschädigung des Instruments zur Folge haben.
Z Open the box and remove all the parts.
On opening the box you should find the parts shown in
the illustration above. Check to make sure that all the
required parts are provided.
X Carefully lean the main unit against a wall.
To make it easier to install the legs, place a soft blanket
or similar material on the floor near a wall, close the
Clavinova keyboard cover, place the front panel of the
Clavinova (the side with the keyboard) on the blanket
and gently lean the unit against the wall — MAKING
SURE THAT IT CAN NOT FALL — as shown in the
illustration.
C Attach the front legs.
Securely attach the two front legs using three screws
for each leg (use a Philips “+” screwdriver) as shown in
the illustration. Make sure that the screws are firmly
tightened.
Z Den Versandkarton öffnen und alle Teile
auspacken.
Der Karton sollte alle in der Abbildung gezeigten Teile
enthalten. Vergewissern Sie sich, daß alle Teile vollzählig vorhanden sind.
X Die Haupteineit vorsichtig an eine Wand lehnen.
Um das Anschrauben der Beine zu erleichtern, breiten
Sie eine Decke oder ein weiches Tuch neben der Wand
auf dem Boden aus, schließen den Tastaturdeckel des
Clavinova, stellen das Instrument mit der Vorderkante
(Seite mit der Tastatur) vorsichtig auf die Decke und
lehnen es an die Wand, wie in der Abbildung gezeigt.
VERGEWISSERN SIE SICH, DASS DAS INSTRUMENT NICHT KIPPEN ODER WEGRUTSCHEN KANN!
C Die vorderen Beine montieren.
Schrauben Sie die beiden vorderen Beine mit jeweils
drei Schrauben (Kreuzschlitzschraubendreher verwenden!) gut am Clavinova fest, wie in der Abbildung
gezeigt. Ziehen Sie die Schrauben fest an.
136
2
3
Blanket, etc.
Decke o. ä.
Couverture, etc.
Manta, etc.
Three screws on each side
Drei Schrauben pro Bein
Trois vis de chaque côté
Tres tornillos en cada lado
CVP-79A:
Montage
CVP-79A:
Montaje
○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○
• Nous ne vous conseillons pas d’essayer d’assembler le Clavinova
seul. Toutefois, ce travail peut être facilement exécuté par deux
personnes.
• No le recomendamos que monte la Clavinova usted solo. Sin
embargo, el trabajo podrá realizarse con más facilidad entre dos
personas solamente.
• N’utilisez que les vis fournies ou des vis ayant exactement les
mêmes dimensions. L’utilisation de vis de dimensions incorrectes
pourrait endommager l’instrument.
• Emplee sólo los tornillos suministrados u otros que sean exactamente del mismo tamaño especificado. El empleo de tornillos del
tamaño erróneo puede dañar el instrumento.
Z Ouvrez le carton et retirez toutes les pièces.
Z Abra la caja y extraiga todas las partes.
Les pièces indiquées sur l’illustration devraient toutes
se trouver dans le carton. Vérifiez qu’il n’en manque
aucune.
Al abrir la caja, encontrará las partes mostradas en la
ilustración de arriba. Compruebe y asegúrese de que
no falta ninguna de las partes requeridas.
X Appuyez le clavier contre un mur en faisant
X Incline con cuidado la unidad principal con-
très attention.
Pour faciliter la pose des pieds, placez une couverture
épaisse, ou un matériau similaire, sur le plancher à
proximité d’un mur. Fermez le cache-clavier et placez
la face avant du Clavinova (côté clavier) sur la couverture et appuyez ensuite le clavier contre le mur de la
manière illustrée. ASSUREZ-VOUS QU’IL NE
PEUT PAS TOMBER.
tra una pared.
Para facilitar la instalación de las patas, coloque una
manta blanda o un material semejante sobre el piso
cerca de una pared, cierre la cubierta del teclado de la
Clavinova, coloque el panel frontal de la Clavinova (el
lado con el teclado) sobre la manta e incline con cuidado la unidad contra la pared — ASEGURANDOSE
DE QUE NO PUEDA CAERSE — como se muestra
en la ilustración.
C Posez les pieds avant.
Fixez les deux pieds avant en utilisant trois vis par pied
(utilisez un tournevis cruciforme “+”) comme illustré.
Vérifiez que les vis sont serrées à fond.
C Coloque las patas delanteras.
Fije las dos patas delanteras usando tres tornillos para
cada pata (emplee un destornillador de cabeza en cruz
“+”) como se muestra en la ilustración. Asegúrese de
que los tornillos queden bien apretados.
137
4
Four screws on each side
Jeweils vier Schrauben an Vorderund Hinterseite
Quatre vis de chaque côté
Cuatro tornillos en cada lado
V Attach the speaker box.
Remove the speaker box cover (attached with
“Velcro”) from the speaker box. Gently rest the speaker
box onto the corresponding brackets on the front legs.
(Be careful not to touch the speakers when handling
the speaker box. Damage may result.) Make sure the
speaker cord is extending out from the rear of the
speaker box. Secure the speaker box to the main keyboard unit using four screws on each side. Insert the
speaker cord connector into the corresponding socket
on the main keyboard unit, making sure that the protruding clip on the connector is facing left.
B Attach the pedal box assembly.
Before attaching the rear leg and pedal box assembly,
insert the pedal cord plug extending from the rear leg
into the corresponding socket in the main unit. Make
sure that the protruding clip on the connector is facing
up. Put the excess cord into the leg and securely attach
the rear leg and pedal assembly using 5 screws for each
leg (three screws per leg and two screws on each leg
bracket).
N Secure the speaker box.
Stand the main unit on its legs and securely attach the
speaker box to the bracket on the front legs using two
screws for each bracket. If it is impossible to align the
bracket holes with the speaker box holes, slightly
loosen the three screws on each of the front legs, align
the holes, and secure the speaker box. After the speaker
box is firmly attached, retighten the screws on the front
legs firmly. Put the speaker box cover back in place
with the “Velcro” on the cover and speaker box. (Make
sure the cut out corners of the speaker cover mask the
brackets.)
138
V Den Lautsprecherkasten montieren.
Nehmen Sie die von Klettband gehaltene Bespannung
vom Lautsprecherkasten ab. Setzen Sie den
Lautsprecherkasten vorsichtig auf die Halterungen an
den vorderen Beinen. (Vermeiden Sie dabei unbedingt
ein Berühren der Lautsprechermembrane.) Das
Lautsprecherkabel muß an der Hinterseite (d.h. oben)
aus dem Lautsprecherkasten ragen. Schrauben Sie den
Lautsprecherkasten mit jeweils vier Schrauben an
Vorder- und Hinterseite an der Haupteinheit fest.
Schließen Sie dann das Lautsprecherkabel an die
Buchse der Haupteinheit an (die Führungsnase am
Stecker muß dabei nach links weisen).
B Die Pedalkastengruppe montieren.
Bevor Sie die Pedalkastengruppe mit den hinteren Beinen montieren, schließen Sie das aus dem einen Bein
ragende Pedalkabel an die entsprechende Buchse der
Haupteinheit an (die Führungsnase am Stecker muß
dabei nach oben weisen). Schieben Sie überlanges
Kabel wieder in das Bein zurück, und schrauben Sie
dann die Pedalkastengruppe mit fünf Schrauben pro
Bein (jeweils 3 für das Bein selbst und 2 für die
Halterung am Bein) an die Haupteinheit.
N Den Lautsprecherkasten an den vorderen
Beinen sichern.
Stellen Sie das Instrument nun auf seine Beine, um den
Lautsprecherkasten zusätzlich mit jeweils zwei Schrauben an die Halterungen der beiden vorderen Beine zu
schrauben. Sollten die Schraubenbohrungen nicht zur
Deckung gebracht werden können, lösen Sie die
Befestigungsschrauben der vorderen Beine ein wenig.
Nach Festschrauben des Lautsprecherkastens dürfen Sie
jedoch nicht vergessen, die Schrauben der Beine wieder
fest anzuziehen. Bringen Sie nun die Bespannung wieder
an, indem Sie die Klettband-Gegenstücke an
Bespannungsrahmen und Lautsprecherkasten aufeinander
ausrichten. (Die Halterungen müssen in den ausgesparten
Mulden des Bespannungsrahmens zu liegen kommen.)
5
Five screws on each side
Fünf Schrauben pro Bein
Cinq vis de chaque côté
Cinco tornillos en cada lado
6
Two screws on each side
Jeweils zwei Schrauben links und rechts
Deux vis de chaque côté
Dos tornillos en cada lado
V Posez la boîte des haut-parleurs.
Retirez le couvercle (fixé au moyen de velcro) de la
boîte des haut-parleurs. Poser la boîte des hautparleurs sur les ferrures correspondantes des pieds
avant. (Faites bien attention de ne pas toucher les hautparleurs lorsque vous manipulez la boîte. Cela pourrait
les endommager.) Assurez-vous que le cordon des
haut-parleurs sort de l’arrière de la boîte. Fixez la
boîte sur le clavier en utilisant quatre vis de chaque
côté. Branchez le connecteur du cordon des hautparleurs à la prise correspondante du clavier en veillant
à ce que la partie en saillie du connecteur soit dirigée
vers la gauche.
B Fixez le pédalier.
Avant de poser l’ensemble pied arrière/pédalier, branchez le connecteur du cordon de pédalier sortant du
pied arrière à la prise correspondante du clavier.
Veillez à ce que la partie en saillie du connecteur soit
dirigée vers le haut. Placez le cordon en excès dans le
pied et fixer solidement l’ensemble pied arrière/pédalier en utilisant 5 vis pour chaque pied (trois vis par
pied et deux vis pour chaque ferrure de fixation).
N Fixer la boîte des haut-parleurs.
Mettez le clavier sur ses pieds et fixez la boîte des
haut-parleurs à la ferrure de fixation des pieds avant à
l’aide de deux vis par ferrure. S’il est impossible d’aligner les trous des ferrures de fixation sur les trous de la
boîte des haut-parleurs, desserrez légèrement les trois
vis de chaque pied avant, alignez les trous et fixez la
boîte des haut-parleurs. Reposez le couvercle de la
boîte des haut-parleurs et fixez-le au moyen des velcros
du couvercle et de la boîte. (Assurez-vous que les
coins découpés du couvercle cachent bien les ferrures.)
V Monte la caja de altavoces.
Extraiga la cubierta de la caja de altavoces (unida con
cinta de adhesión por contacto) de la caja de altavoces.
Apoye con cuidado la caja de altavoces en las ménsulas
correspondientes de las patas delanteras. (Tenga cuidado
en no tocar los altavoces cuando se manipule la caja de
altavoces. Podrían ocasionarse daños.) Asegúrese de que
el cable de altavoz se extienda desde la parte posterior de
la caja del altavoz. Fije le caja de altavoces a la unidad
del teclado principal usando cuatro tornillos en cada lado.
Inserte el conector del cable de altavoces en el receptáculo correspondiente de la unidad del teclado principal,
asegurándose de que el retenedor que sobresale del
conector queda orientado hacia la izquierda.
B Monte el conjunto de la caja de pedales
Antes de montar la pata trasera y el conjunto de la caja
de pedales, inserte la clavija del cables de los pedales,
que se extiende desde la pata trasera al receptáculo
correspondiente de la unidad principal. Asegúrese de
que el retenedor que sobresale del conector queda
orientado hacia arriba. Ponga el cable sobrante en la
pata y fije con seguridad la pata trasera y el conjunto
de pedales usando 5 tornillos para cada pata (tres tornillos por pata y dos tornillos en la ménsula de cada pata.
N Fije la caja de altavoces
Apoye la unidad principal sobre sus patas y monte con
seguridad la caja de altavoces en la ménsula de las patas
delanteras usando dos tornillos para cada ménsula. Si es
imposible alinear los orificios de las ménsulas con los
orificios de la caja de altavoces, afloje un poco los tres
tornillos de cada una de las patas delanteras, alinee los
orificios, y fije la caja de altavoces. Después de haber
montado firmemente la caja de altavoces, vuelva a apretar bien los tornillos de las patas delanteras. Ponga de
nuevo la cubierta de la caja de altavoces en su lugar con
la cinta de adhesión por contacto de la cubierta y de la
caja de altavoces. (Asegúrese de que las esquinas cortadas de la cubierta de altavoces encubre las ménsulas.)
139
7
● A voltage selector is provided in some areas.
● Spannungswähler
(nur in bestimmten Verkaufsgebieten)
● Un sélecteur de tension est prévu pour
certaines régions
● El selector de tensión está provisto para
ciertos destinos.
240
220
110
127
M Voltage Selector
Before connecting the AC power cord, check the setting of the voltage selector which is provided in some
areas. To set the selector for 110V, 127V, 220V or
240V main voltages, use a “minus” screwdriver to
rotate the selector dial so that the correct voltage for
your region appears next to the pointer on the panel.
The voltage selector is set at 240V when the unit is
initially shipped.
After the proper voltage has been selected connect the
AC power cord. A plug adaptor may be also provided
in some areas to match the pin configuration of the AC
wall outlets in your area.
< Set the Adjusters.
For stability, four adjusters are provided on the bottom
of the pedal box and rear leg assembly. After positioning the Clavinova in its intended location, rotate the
adjusters until they come in firm contact with the floor
surface. The adjusters ensure stable pedal operation
and facilitates pedal effect control. If the adjusters are
not in firm contact with the floor surface, distorted
sound may result.
• After assembling the Clavinova, check once more to make sure
that all screws have been securely fastened.
• If the stand leans to the side, makes unusual noises, or otherwise
seems unstable during use, check and tighten all screws while
following the assembly instructions given above.
140
M Den Spannungswähler einstellen.
Bevor Sie nun das Netzkabel anschließen, müssen Sie
den Spannungswähler (falls vorhanden) auf die örtliche
Netzspannung einstellen. Zum Verstellen drehen Sie
den Spannungswähler mit einem
Schlitzschraubendreher, bis der richtige Spannungswert
(110, 127, 220 oder 240) an der Pfeilmarkierung steht.
Bei der Auslieferung werden alle Instrumente mit
Spannungswähler auf “240” voreingestellt.
Nachdem Sie den Spannungswähler richtig eingestellt
haben, können Sie nun das Netzkabel anschließen. In
manchen Gebieten wird ein Steckerdapter mitgeliefert,
um den Anschluß an die evtl. unterschiedlich geformte
Steckdose zu ermöglichen.
< Die Pedalstützen einstellen.
Für bessere Standfestigkeit sind unter der Pedalkastengruppe vier verstellbare Pedalstützen vorgesehen.
Nachdem Sie das Clavinova an seinem festen Standplatz aufgestellt haben, drehen Sie diese Stützen heraus, bis sie fest auf dem Boden stehen. Die Stützen
sorgen beim Spielen für präzise Pedalbetätigung. Wenn
die vier Pedalstützen nicht fest auf dem Boden aufstehen, können Klangverzerrungen auftreten.
• Vergewissern Sie sich nach Zusammenbau und Aufstellung des
Clavinova noch einmal davon, daß alle Schrauben fest angezogen
sind.
• Wenn das Instrument schief steht, komische Geräusche erzeugt
oder sich beim Spielen wackelig anfühlt, prüfen Sie gemäß den
obigen Anweisungen, ob das Instrument richtig zusammengebaut
wurde, und ziehen dabei die einzelnen Schrauben noch einmal
nach.
8
M Sélecteur de tension
Avant de connecter le cordon d’alimentation, vérifiez
le réglage du sélecteur de tension qui est prévu pour
certaines régions. Pour régler le sélecteur sur 110 V,
127 V, 220 V ou 240 V, utilisez un tournevis à lame
plate pour tourner le cadran du sélecteur afin de mettre
l’indication correspondant à la tension de votre région
vis à vis du repère triangulaire situé sur le panneau. Le
sélecteur de tension est réglé sur 240 V au départ
d’usine.
Une fois que vous avez réglé le sélecteur de tension,
connectez le cordon d’alimentation. Un adaptateur de
prise peut également être fourni dans certaines régions
pour pouvoir brancher le cordon à la prise secteur murale.
< Réglez la hauteur du pédalier.
Pour assurer la stabilité, quatre dispositifs de réglage
ont été prévus à la partie inférieure de l’ensemble pédalier/pied arrière. Après avoir placé le Clavinova à l’endroit où vous souhaitez l’installer, tournez ces dispositifs jusqu’à ce qu’ils soient en contact ferme avec la
surface du sol. Ces dispositifs assurent la stabilité du
pédalier lors de son utilisation et facilitent la commande au pied des effets. Si ces dispositifs ne sont pas
en contact ferme avec le sol, il pourra se produire une
distorsion du son.
M Selector de tensión
Antes de conectar el cable de alimentación de CA,
compruebe el ajuste del selector de tensión que se incorpora para ciertos destinos. Para ajustar el selector a
110V, 127V, 220V ó 240V de la red de alimentación,
emplee un destornillador de cabeza recta “-” para girar
el selector de modo que la tensión correcta de su zona
aparezca al lado del indicador del panel. El selector de
tensión se ajusta a 240V cuando la unidad sale de fábrica.
Después de haber seleccionado la tensión correcta,
enchufe el cable de alimentación. En algunas zonas
puede suministrarse también un adaptador para adaptar
la configuración de las patillas de los tomacorrientes de
CA de su localidad.
< Ajuste los reguladores
Para más estabilidad, se proporcionan cuatro reguladores en la parte inferior de la caja de pedales y en el
conjunto de la pata trasera. Después de situar la
Clavinova en la posición deseada, gire los reguladores
hasta que hagan buen contacto con la superficie del
piso. Los reguladores aseguran una operación estable
de los pedales y facilitan el control de los efectos con
los pedales. Si los ajustadores no están en buen contacto con la superficie del piso, el sonido podría
distorsionarse.
• Après avoir assemble le Clavinova, vérifiez de nouveau que toutes
les vis sont bien serrées à fond.
• Después de haber montado la Clavinova, compruebe una vez más
que todos los tornillos se hayan apretado bien.
• Si l’instrument penche d’un côté, s’il fait un bruit inhabituel, ou s’il
paraît instable lorsque vous l’utilisez, vérifiez que vous l’avez assemblé correctement et que toutes les vis sont bien serrées en
suivant les instructions de montage données ici.
• Si el soporte se inclina a un lado, hace ruidos anormales, o parece
inestable durante la utilización, compruebe y apriete todos los
tornillos siguiendo las instrucciones de montaje anteriores.
141
1
A
5 x 50 mm long gold-colored screws x 6
Goldfarbene Schrauben (5 x 50 mm) x 6
Vis longues dorées de 5 x 50 mm x 6
Tornillos dorados largos de 5 x 50 mm x 6
1
6 x 20 mm large flat-head screws (black) x 8
Senkschrauben (6 x 20 mm) x 8
Grosses vis à tête plate de 6 x 20 mm (noires) x 8
Tornillos grandes de cabeza plana (negros) de
6 x 20 mm x 8
2
4 x 20 mm small round-head screws (black) x 8
Rundkopfschrauben (4 x 20 mm) x 8
Petites vis à tête ronde de 4 x 20 mm (noires) x 8
Tornillos pequeños de cabeza redonda (negros) de
4 x 20 mm x 8
3
B
C
E
D
C
D
● AC power cord
● Netzkabel
● Cordon d’alimentation
● Cable de alimentación de CA
CVP-69/69A:
Assembly
CVP-69A/69:
Zusammenbau
○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○
• We do not recommend attempting to assemble the Clavinova
alone. The job can be easily accomplished, however, with only two
people.
• Wir raten Ihnen davon ab, das Clavinova alleine zusammenzubauen und aufzustellen. Zwei Personen können diese Arbeit jedoch
problemlos ausführen.
• Use only the screws provided or replacements of exactly the specified size. Using screws of the wrong size can result in damage to
the instrument.
• Verwenden Sie ausschließlich die mitgeliefenten Schrauben oder
Ersatzschrauben identischer Größe. Die Verwendung von Schrauben mit abweichenden Maßen kann eine Beschädigung des Instruments zur Folge haben.
Z Open the box and remove all the parts.
Z Den Versandkarton öffnen und alle Teile
On opening the box you should find the parts shown in
the illustration. Check to make sure that all the required
parts are provided.
X Attach the feet (D) to the side panels (C).
Secure the feet (D) to the side panels (C) using three 5
x 50 mm long gold-colored screws 1 for each side.
Make sure the rounded edge of the side panels and the
protruding end of the feet are facing front.
C Attach the speaker box (B) to the side panels (C).
Remove the speaker box cover (attached with
“Velcro”) from the speaker box. (Be careful not to
touch the speakers when handling the speaker box.
Damage may result.) Secure the speaker box (B) to the
side panels (C), as shown in the illustration, using one
6 x 20 mm (large flat-head) screw 2 for each bottom
bracket and two 4 x 20 mm (small round-head) screws
3 for each side bracket. Make sure the side brackets
are positioned inside of the speaker box (as shown in
the illustration) before securing.
142
auspacken.
Der Karton sollte alle in der Abbildung gezeigten Teile
enthalten. Vergewissern Sie sich, daß alle Teile vollzählig vorhanden sind.
X Die Füße (D) an die Seitenwände (C) schrauben.
Schrauben Sie die beiden Füße (D) mit jeweils drei
goldfarbenen Schrauben (5 x 50 mm) 1 an den
Seitenwänden (C) fest. Die abgerundete Kante der
Seitenwände und das hervorspringende Ende der Füße
müssen dabei nach vorne weisen.
C Den Lautsprecherkasten (B) mit den Seitenwänden (C) verschrauben.
Nehmen Sie die von Klettband gehaltene Bespannung
vom Lautsprecherkasten ab. (Vermeiden Sie bei der
Handhabung des Lautsprecherkastens unbedingt ein
Berühren der Lautsprechermembrane, da diese leicht
beschädigt werden.) Schrauben Sie nun den
Lautsprecherkasten (B), wie in der Abbildung gezeigt,
an den Seitenwänden (C) fest: Verwenden Sie jeweils
eine Senkschraube (6 x 20 mm) 2 zum Befestigen an
den beiden unteren Halterungen und jeweils zwei
Rundkopfschrauben (4 x 20 mm) 3 zum Verschrauben
mit den beiden seitlichen Halterungen. Vergewissern
Sie sich vor dem Eindrehen der Schrauben, daß die
Halterungen sich im Pedalkasten befinden (d.h. nicht
sichtbar sind), wie in der Abbildung angedeutet.
2
3
B
C
B
C
D
5 x 50 mm long gold-colored screws
Goldfarbene Schrauben (5 x 50 mm)
Vis longues dorées de 5 x 50 mm
Tornillos dorados largos de 5 x 50 mm
1
4 x 20 mm (small round-head) screws
Rundkopfschrauben (4 x 20 mm)
Petites vis de 4 x 20 mm (à tête ronde)
Tornillos de 4 x 20 mm (pequeños de cabeza redonda)
3
6 x 20 mm (large flat-head) screw
Senkschraube (6 x 20 mm)
Grosses vis de 6 x 20 mm (à tête plate)
Tornillo de 6 x 20 mm (grande de cabeza plana)
2
CVP-69/69A:
Montage
CVP-69/69A:
Montaje
○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○
• Nous ne vous conseillons pas d’essayer d’assembler le Clavinova
seul. Toutefois, ce travail peut être facilement exécuté par deux
personnes.
• No le recomendamos que monte la Clavinova usted solo. Sin
embargo, el trabajo podrá realizarse con más facilidad entre dos
personas solamente.
• N’utilisez que les vis fournies ou des vis ayant exactement les
mêmes dimensions. Le fait d’utiliser des vis de dimensions incorrectes pourrait endommager l’instrument.
• Emplee sólo los tornillos suministrados u otros que sean exactamente del mismo tamaño especificado. El empleo de tornillos del
tamaño erróneo puede dañar el instrumento.
Z Ouvrez le carton et retirez toutes les pièces.
Z Abra la caja y extraiga todas las partes.
Les pièces indiquées sur l’illustration devraient toutes
se trouver dans le carton. Vérifiez qu’il n’en manque
aucune.
X Montez les supports inférieurs (D) sur les
panneaux latéraux (C)
Fixez les supports inférieurs (D) aux panneaux latéraux
(C) en utilisant trois vis longues dorées de 5 x 50 mm
1 de chaque côté. Veillez à ce que le bord arrondi des
panneaux latéraux et la partie qui dépasse des supports
inférieurs soient dirigés vers l’avant.
C Fixez la boîte des haut-parleurs (B) aux panneaux latéraux (C)
Retirez le couvercle (fixé au moyen de velcro) de la
boîte des haut-parleurs. (Faites bien attention de ne pas
toucher les haut-parleurs lorsque vous manipulez la
boîte. Cela pourrait les endommager.) Fixez la boîte
des haut-parleurs (B) aux panneaux latéraux (C) de la
manière illustrée en utilisant une grosse vis 2 de 6 x
20 mm (à tête plate) pour chaque ferrure inférieure et
deux petites vis 3 de 4 x 20 mm (à tête ronde) pour
chaque ferrure latérale. Assurez-vous que les ferrures
latérales sont bien positionnées à l’intérieur de la boîte
des haut-parleurs (comme montré sur l’illustration)
avant de serrer les vis.
Al abrir la caja, encontrará las partes mostradas en la
ilustración de arriba. Compruebe y asegúrese de que
no falta ninguna de las partes requeridas.
X Monte las patas (D) en los paneles laterales (C).
Fije las patas (D) a los paneles laterales (C) usando tres
tornillos durados largos de 5 x 50 mm 1 para cada
lado. Asegúrese de que el borde redondeado de los
paneles laterales y el extremo que sobresale de los pies
queden orientados hacia adelante.
C Monte la caja de altavoces (B) en los paneles laterales (C).
Extraiga la cubierta de la caja de altavoces (unida con
cinta de adhesión por contacto) de la caja de altavoces.
(Tenga cuidado en no tocar los altavoces cuando se
manipule la caja de altavoces. Podrían ocasionarse
daños.) Fije le caja de altavoces (B) a los paneles laterales (C), como se muestra en la ilustración, usando un
tornillo de 6 x 20 mm (grande de cabeza plana) 2 para
cada ménsula inferior y dos tornillos de 4 x 20 mm
(pequeños de cabeza redonda) 3 para cada ménsula
lateral. Asegúrese de que las ménsulas laterales queden situadas dentro de la caja de altavoces (como se
muestra en la ilustración) antes de la fijación.
143
4
4 x 20 mm (small round-head) screws
Rundkopfschrauben (4 x 20 mm)
Petites vis de 4 x 20 mm (à tête ronde)
Tornillos de 4 x 20 mm
(pequeños de cabeza redonda)
3
B
C
6 x 20 mm (large flat-head) screw
Senkschraube (6 x 20 mm)
Grosses vis de 6 x 20 mm (à tête plate)
Tornillo de 6 x 20 mm (grande de cabeza plana)
2
V Attach the pedal box (E) to the speaker box
(B).
Secure the pedal box (E) to the speaker box (B) using
one 6 x 20 mm (large flat-head) screw 2 for each
bottom bracket and two 4 x 20 mm (small round-head)
screws 3 for each rear bracket. Make sure that the
pedal cord passes through the recess in the top of the
pedal assembly and the speaker cord is extending out to
the rear from the top of the speaker box (see illustration).
B Attach the main keyboard unit (A). (Part 1)
Gently lower the main keyboard unit (A) onto the
speaker box (B) and stand assembly so that the rear of
the main unit is positioned about 10cm behind the back
of the side panel. WATCH YOUR FINGERS WHEN
DOING THIS!! Insert one 6 x 20 mm (large flat-head)
screw 2 into the innermost hole leaving about 1cm of
the screw protruding on each side of the main unit’s
bottom panel. These screws will slide into the rear
side-panel brackets in step 6.
* Keep your fingers away from the area marked “Danger Zone” in
the illustrations when lowering the main keyboard unit onto the
stand assembly.
144
V Den Pedalkasten (E) am Lautsprecherkasten
(B) festschrauben.
Schrauben Sie den Pedalkasten mit jeweils einer Senkschraube (6 x 20 mm) 2 für die beiden unteren
Halterungen und zwei Rundkopfschrauben (4 x 20
mm) 3 für die beiden hinteren Halterungen an den
Lautsprecherkasten (B). Achten Sie dabei darauf, daß
das Pedalkabel oben aus dem einen Bein des Pedalkastens ragt und das Lautsprecherkabel nach hinten
gelegt ist, wie in der Abbildung gezeigt.
B Die Haupteinheit (A) montieren. (Teil 1)
Setzen Sie die Haupteinheit (A) vorsichtig so auf den
Lautsprecherkasten und die Seitenwände, daß ihre
Hinterseite etwa 10 cm über den Hinterkanten der
Seitenwände übersteht. VORSICHT! KLEMMEN
SIE SICH DABEI NICHT DIE FINGER EIN! Drehen Sie hinten an der Unterseite der Haupteinheit links
und rechts jeweils eine Senkschraube (6 x 20 mm) 2
in die innere Bohrung, so daß noch etwa 1 cm Gewinde
hervorsteht. Diese Schrauben greifen in Schritt 6 in die
hinteren Halterungen der Seitenwände.
* Halten Sie beim Aufsetzen der Haupteinheit auf die Ständerbaugruppe von dem in der Abbildung mit “Gefahrenzone” gekennzeichneten Bereich fern.
5
Danger Zone
Gefahrenzone
Zones dangereuses
Zona peligrosa
A
A
C
B
● 10 cm behind the side panel
● 10 cm Überstand
● 10 cm derrière le panneau latéral
● 10 cm detrás del panel lateral
6 x 20 mm (large flat-head) screw
Senkschraube (6 x 20 mm)
Grosses vis de 6 x 20 mm (à tête plate)
Tornillo de 6 x 20 mm (grande de cabeza plana)
V Fixez le pédalier (E) à la boîte des hautparleurs (B).
Fixez le pédalier (E) à la boîte des haut-parleurs (B) en
utilisant une grosse vis 2 de 6 x 20 mm (à tête plate)
pour chaque ferrure inférieure et deux petites vis 3 de
4 x 20 mm (à tête ronde) pour chaque ferrure arrière.
Assurez-vous que le cordon du pédalier passe dans la
découpe à la partie supérieure du pédalier et que le
cordon des haut-parleurs sort vers l’arrière de la boîte
des haut-parleurs (voir l’illustration).
B Posez le clavier (A) (1ère étape)
Abaissez le clavier (A) avec précaution sur la boîte des
haut-parleurs (B) et sur les supports de manière que
l’arrière du clavier dépasse de 10 cm environ derrière
les panneaux latéraux. FAITES ATTENTION A VOS
DOIGTS EN EXECUTANT CETTE OPERATION
!! Mettez une vis 2 de 6 x 20 mm (à tête plate) dans
le trou le plus à l’intérieur de chaque côté du clavier de
manière que ces vis sortent d’environ 1 cm du panneau
inférieur. Ces vis se glisseront dans les ferrures arrière
des panneaux latéraux au cours de l’étape 6.
* Lorsque vous abaissez le clavier sur son support, ne placez
pas les mains dans les zones marquées “Zones dangereuses”
sur l’illustration.
2
V Monte la caja de pedales (E) en la caja de
altavoces (B).
Fije la caja de pedales (E) a la caja de altavoces (B)
usando un tornillo de 6 x 20 mm (grande de cabeza
plana) 2 para cada ménsula inferior y dos tornillos de
4 x 20 mm (pequeños de cabeza redonda) 3 para cada
ménsula trasera. Asegúrese de que el cable de los pedales pasa por el hueco de la parte superior del conjunto de pedales y que el cable de altavoces sale por la
parte posterior de encima de la caja de altavoces (vea la
ilustración).
B Monte la unidad del teclado principal (A).
(Parte 1)
Baje con cuidado la unidad del teclado principal (A) a
la caja de altavoces (B) y conjunto del soporte de modo
que la parte posterior de la unidad principal quede situada a unos 10 cm detrás de la parte posterior del panel lateral. ¡CUANDO LO HAGA, TENGA CUIDADO CON LOS DEDOS! Inserte un tornillo de 6 x
20 mm (grande de cabeza plana) 2 en el orificio más
interior dejando aproximadamente 1 cm del tornillo
sobresaliendo en cada lado del panel inferior de la unidad principal. Estos tornillos se deslizarán a las
ménsulas del panel lateral trasero en el paso 6.
* Mantenga apartados los dedos de la parte marcada con “Zona
peligrosa” en las ilustraciones cuando baje la unidad del teclado principal al conjunto del soporte.
145
6
A
6 x 20 mm (large flat-head) screw
Senkschraube (6 x 20 mm)
Grosses vis de 6 x 20 mm (à tête plate)
Tornillo de 6 x 20 mm
(grande de cabeza plana)
2
A
N Attach the main keyboard unit. (Part 2)
With the protruding screw heads on the bottom panel
of the main unit positioned behind the side-panel rear
brackets, slide the main keyboard unit forward until the
screw heads stop against the end of the slot in the rear
brackets. Align the holes in the bottom of the main unit
with those in the front side-panel brackets (also center
the main unit to produce an equal clearance on the left
and right sides, as shown in the illustrations), then secure the main keyboard unit to the stand assembly using two 6 x 20 mm (large flat-head) screws 2 screwed
through the front bracket and then firmly tightening the
two protruding screws that slid into the rear brackets.
Put the speaker box cover back in place with the
“Velcro” on the cover and speaker box. (Make sure that
the upper edge of the cover fits snugly against the under side of the main unit.)
M Connect the speaker cord and pedal cord.
Insert the speaker cord connector into the corresponding socket on the right (closest to the pedal box) of the
keyboard unit. Plug the pedal cord connector into the
socket on the left (farthest from the pedal box) of the
keyboard unit. Note that both connectors must be inserted with the protruding clip facing the rear of the
main unit.
146
A
C
N Die Haupteinheit montieren. (Teil 2)
Positionieren Sie die Haupteinheit so auf der Ständerbaugruppe, daß die beiden eingedrehten Schrauben
hinter den hinteren Halterungen an den Seitenwänden
zu liegen kommen, und schieben Sie dann nach vorn,
bis die Schrauben bis zum Anschlag in den
Halterungsschlitzen sitzen. Bringen Sie die Bohrungen
der vorderen Halterungen mit denen an der Unterseite
der Haupteinheit zur Deckung (achten Sie auch darauf,
daß die Haupteinheit mittig positioniert ist, d.h. links
und rechts gleichviel übersteht, wie in der Abbildung
gezeigt), und schrauben Sie die Haupteinheit dann mit
zwei weiteren Senkschrauben (6 x 20 mm) 2 an den
vorderen Halterungen fest, um danach die beiden bereits eingedrehten Schrauben fest anzuziehen. Bringen
Sie nun die Bespannung wieder an, indem Sie die
Klettband-Gegenstücke an Bespannungsrahmen und
Lautsprecherkasten aufeinander ausrichten. (Die Oberkante des Bespannungsrahmens muß bündig an der
Unterseite der Haupteinheit anliegen.)
M Das Lautsprecherkabel und das Pedalkabel
anschließen.
Schließen Sie das Lautsprecherkabel an die rechte
(dem Pedalkasten am nächsten gelegene) Buchse an an
der Unterseite der Haupteinheit an. Das Pedalkabel
schließen Sie an die linke (am weitesten vom Pedalkasten entfernte) Buchse an. Die beiden Stecker müssen mit der Führungsnase in Richtung Rückseite (der
Haupteinheit) in die jeweilige Buchse gesteckt werden.
7
N Posez le clavier (A) (2ère étape)
Les têtes de vis sortant du panneau inférieur du clavier
étant positionnées derrière les ferrures arrières des panneaux latéraux, faites glisser le clavier vers l’avant
jusqu’à ce que les têtes de vis soient en butée contre le
fond de la fente des ferrures arrière. Alignez les trous
du panneau inférieur du clavier sur les trous des ferrures avant des panneaux latéraux (centrez également le
clavier de manière à avoir un jeu identique de chaque
côté, comme illustré). Fixez ensuite le clavier sur le
support en vissant une grosse vis 2 de 6 x 20 mm (à
tête plate) à travers chaque ferrure avant et en serrant à
fond les deux vis glissées dans les ferrures arrière. Reposez le couvercle de la boîte des haut-parleurs et
fixez-le au moyen des velcros du couvercle et de la
boîte. (Assurez-vous que le bord supérieur du couvercle est bien calé contre le panneau inférieur du clavier.)
M Connectez le cordon des haut-parleurs et le
cordon du pédalier.
Branchez le connecteur du cordon des haut-parleurs à
la prise correspondante sur le côté droit du clavier (la
plus proche du pédalier). Branchez le connecteur du
cordon du pédalier à la prise située sur le côté gauche
du clavier (la plus éloignée du pédalier). Veuillez noter
que les deux connecteurs doivent être branchés avec la
partie en saillie dirigée vers l’arrière du clavier.
N Monte la unidad del teclado principal.
(Parte 2)
Con las cabezas de tornillos sobresaliendo por el panel
inferior de la unidad principal situado detrás de las
ménsulas traseras del panel lateral, deslice la unidad
del teclado principal hacia adelante hasta que las cabezas de tornillos topen contra el extremo de la ranura de
las ménsulas traseras. Alinee los orificios de la parte
inferior de la unidad principal con los de las ménsulas
del panel lateral frontal (centre también la unidad principal para producir una holgura igual en los lados izquierdo y derecho, como se muestra en las ilustraciones), y fije entonces la unidad del teclado principal en
el conjunto del soporte usando dos tornillos de 6 x 20
mm (grandes de cabeza plana) 2 enroscados por la
ménsula frontal y apriete entonces bien los tornillos
que sobresalen que se incorporan en las ménsulas traseras. Ponga de nuevo la cubierta de la caja de altavoces
en su lugar con la cinta de adhesión por contacto de la
cubierta y de la caja de altavoces. (Asegúrese de que el
borde superior de la cubierta se adapta bien contra el
lado inferior de la unidad principal.)
M Conecte el cable de altavoces y el cable de
pedales.
Inserte el conector del cable de altavoces en el receptáculo correspondiente de la derecha (más cercano a la
caja de pedales) de la unidad del teclado. Enchufe el
conector del cable de pedales en el receptáculo de la
izquierda (el más apartado de la caja de pedales) de la
unidad del teclado. Tenga presente que ambos
conectores deben insertarse con el retenedor saliente
orientado a la parte trasera de la unidad principal.
147
8
● A voltage selector is provided in some areas.
● Spannungswähler
(nur in bestimmten Verkaufsgebieten)
● Un sélecteur de tension est prévu pour
certaines régions
● El selector de tensión está provisto para
ciertos destinos.
220
240
110
127
< Voltage Selector
Before connecting the AC power cord, check the setting of the voltage selector which is provided in some
areas. To set the selector for 110V, 127V, 220V or
240V main voltages, use a “minus” screwdriver to rotate the selector dial so that the correct voltage for your
region appears next to the pointer on the panel. The
voltage selector is set at 240V when the unit is initially
shipped.
After the proper voltage has been selected connect the
AC power cord. A plug adaptor may be also provided
in some areas to match the pin configuration of the AC
wall outlets in your area.
> Be sure to set the pedal adjusters.
For stability, two adjusters are provided on the bottom
of the pedal assembly (E). Rotate the adjusters until
they comes in firm contact with the floor surface. The
adjusters ensure stable pedal operation and facilitate
pedal effect control. If the adjusters are not in firm
contact with the floor surface, distorted sound may
result.
< Den Spannungswähler einstellen.
Bevor Sie nun das Netzkabel anschließen, müssen Sie
den Spannungswähler (falls vorhanden) auf die örtliche
Netzspannung einstellen. Zum Verstellen drehen Sie
den Spannungswähler mit einem
Schlitzschraubendreher, bis der richtige Spannungswert
(110, 127, 220 oder 240) an der Pfeilmarkierung steht.
Bei der Auslieferung werden alle Instrumente mit
Spannungswähler auf “240” voreingestellt.
Nachdem Sie den Spannungswähler richtig eingestellt
haben, können Sie nun das Netzkabel anschließen. In
manchen Gebieten wird ein Steckerdapter mitgeliefert,
um den Anschluß an die evtl. unterschiedlich geformte
Steckdose zu ermöglichen.
> Die Pedalstützen einstellen.
Für bessere Standfestigkeit sind unter dem Pedalkasten
(E) zwei verstellbare Pedalstützen vorgesehen. Nachdem Sie das Clavinova an seinem festen Standplatz
aufgestellt haben, drehen Sie diese Stützen heraus, bis
sie fest auf dem Boden stehen. Die Stützen sorgen
beim Spielen für präzise Pedalbetätigung. Wenn die
beiden Pedalstützen nicht fest auf dem Boden aufstehen, können Klangverzerrungen auftreten.
• After assembling the Clavinova, check once more to make sure
that all screws have been securely fastened.
• If the stand leans to the side, makes unusual noises, or otherwise
seems unstable during use, check and tighten all screws while
following the assembly instructions given above.
• Vergewissern Sie sich nach Zusammenbau und Aufstellung des
Clavinova noch einmal davon, daß alle Schrauben fest angezogen
sind.
• Wenn das Instrument schief steht, komische Geräusche erzeugt
oder sich beim Spielen wackelig anfühlt, prüfen Sie gemäß den
obigen Anweisungen, ob das Instrument richtig zusammengebaut
wurde, und ziehen dabei die einzelnen Schrauben noch einmal
nach.
148
9
E
< Sélecteur de tension
Avant de connecter le cordon d’alimentation, vérifiez
le réglage du sélecteur de tension qui est prévu pour
certaines régions. Pour régler le sélecteur sur 110 V,
127 V, 220 V ou 240 V, utilisez un tournevis à lame
plate pour tourner le cadran du sélecteur afin de mettre
l’indication correspondant à la tension de votre région
vis à vis du repère triangulaire situé sur le panneau. Le
sélecteur de tension est réglé sur 240 V au départ
d’usine.
Une fois que vous avez réglé le sélecteur de tension,
connectez le cordon d’alimentation. Un adaptateur de
prise peut également être fourni dans certaines régions
pour pouvoir brancher le cordon à la prise secteur murale.
> N’oubliez pas de régler la hauteur du péda-
< Selector de tensión
Antes de conectar el cable de alimentación de CA,
compruebe el ajuste del selector de tensión que se incorpora para ciertos destinos. Para ajustar el selector a
110V, 127V, 220V ó 240V de la red de alimentación,
emplee un destornillador de cabeza recta “–” para girar
el selector de modo que la tensión correcta de su zona
aparezca al lado del indicador del panel. El selector de
tensión se ajusta a 240V cuando la unidad sale de fábrica.
Después de haber seleccionado la tensión correcta,
enchufe el cable de alimentación. En algunas zonas
puede suministrarse también un adaptador para adaptar
la configuración de las patillas de los tomacorrientes de
CA de su localidad.
> Asegúrese de ajustar los reguladores de los
lier.
Pour assurer la stabilité, deux dispositifs de réglage ont
été prévus à la partie inférieure du pédalier (E). Tournez ces dispositifs jusqu’à ce qu’ils soient en contact
ferme avec la surface du sol. Ces dispositifs assurent
la stabilité du pédalier lors de son utilisation et facilitent la commande au pied des effets. Si ces dispositifs
ne sont pas en contact ferme avec le sol, il pourra se
produire une distorsion du son.
pedales.
Para más estabilidad, se proporcionan dos reguladores
en la parte inferior del conjunto de pedales (E). Gire
los reguladores hasta que hagan buen contacto con la
superficie del piso. Los reguladores aseguran una operación estable de los pedales y facilitan el control de
los efectos con los pedales. Si los ajustadores no están
en buen contacto con la superficie del piso, el sonido
podría distorsionarse.
• Après avoir assemble le Clavinova, vérifiez de nouveau que toutes
les vis sont bien serrées à fond.
• Después de haber montado la Clavinova, compruebe una vez más
que todos los tornillos se hayan apretado bien.
• Si l’instrument penche d’un côté, s’il fait un bruit inhabituel, ou s’il
paraît instable lorsque vous l’utilisez, vérifiez que vous l’avez assemblé correctement et que toutes les vis sont bien serrées en
suivant les instructions de montage données ici.
• Si el soporte se inclina a un lado, hace ruidos anormales, o parece
inestable durante la utilización, compruebe y apriete todos los
tornillos siguiendo las instrucciones de montaje anteriores.
149
1
A
6 x 25 mm round-head screws x4
Rundkopfschrauben (6 x 25 mm) x 4
Vis à tête ronde de 6 x 25 mm x 4
Tornillos de cabeza redonda de 6 x 25 mm x 4
1
4 x 20 mm round-head screws x4
Rundkopfschrauben (4 x 20 mm) x 4
Vis à tête ronde de 4 x 20 mm x 4
Tornillos de cabeza redonda de 4 x 20 mm x 4
2
6 x 18 mm flat-head screws x6
Senkschrauben (6 x 18 mm) x 6
Vis à tête plate de 6 x 18 mm x 6
Tornillos de cabeza plana de 6 x 18 mm x 6
3
B
C
Bundled pedal cord inside
Gebündeltes Pedalkabel
Cordon de pédalier enroulé à l’intérieur
Cable de pedales enrollado en el interior
D
● AC power cord
● Netzkabel
● Cordon d’alimentation
● Cable de alimentación de CA
CVP-59S:
Assembly
CVP-59S:
Zusammenbau
○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○
• We do not recommend attempting to assemble the Clavinova
alone. The job can be easily accomplished, however, with only two
people.
• Wir raten Ihnen davon ab, das Clavinova alleine zusammenzubauen und aufzustellen. Zwei Personen können diese Arbeit jedoch
problemlos ausführen.
• Use only the screws provided or replacements of exactly the specified size. Using screws of the wrong size can result in damage to
the instrument.
• Verwenden Sie ausschließlich die mitgeliefenten Schrauben oder
Ersatzschrauben identischer Größe. Die Verwendung von Schrauben mit abweichenden Maßen kann eine Beschädigung des Instruments zur Folge haben.
Z Open the box and remove all the parts.
On opening the box you should find the parts shown in
the illustration above. Check to make sure that all the
required parts are provided.
X Attach the side panels (D) to the pedal box
(C).
Before installing the pedal box, untie and straighten out
the bundled cord attached to the bottom of the pedal
box.
Place the pedal box on top of the wooden blocks attached to the side panels (D), and attach using the four
6 x 25 mm round-head screws 1 — two screws on
each side. Make sure the pedals extend in the same
direction as the feet.
C Attach the center panel (B) to the side panels (D).
The center panel (B) should be screwed to the vertical
brackets on the side panels (D) using the four 4 x 20
mm round-head screws 2, as shown in the illustration.
Make sure the center panel is attached to the side of the
brackets facing the pedals.
150
Z Den Versandkarton öffnen und alle Teile
auspacken.
Der Karton sollte alle in der Abbildung gezeigten Teile
enthalten. Vergewissern Sie sich, daß alle Teile vollzählig vorhanden sind.
X Die Seitenwände (D) mit dem Pedalkasten
(C) verschrauben.
Bevor Sie den Pedalkasten festschrauben, lösen Sie
zunächst das an der Unterseite des Pedalkastens befestigte Kabel und ziehen es gerade.
Setzen Sie den Pedalkasten auf die Holzklötze an den
Innenseiten der Seitenwände (D), um ihn dann mit den
vier größeren Rundkopfschrauben (6 x 25 mm) 1
festzuschrauben (jeweils zwei Schrauben links und
rechts). Achten Sie darauf, daß die Pedale und die Füße
in dieselbe Richtung weisen.
C Die Rückwand (B) an die beiden Seitenwände (D) schrauben.
Die Rückwand wird an den beiden senkrecht angebrachten Halterungen mit den vier kleineren Rundkopfschrauben (4 x 20 mm) 2 festgeschraubt, wie in der
Abbildung gezeigt. Achten Sie darauf, daß die Rückwand vor den Halterungen angesetzt und festgeschraubt wird.
2
6 x 25 mm round-head screws
Rundkopfschrauben (6 x 25 mm)
Vis à tête ronde de 6 x 25 mm
Tornillos de cabeza redonda de 6 x 25 mm x 4
3
1
B
D
C
D
C
4 x 20 mm round-head screws
Rundkopfschrauben (4 x 20 mm)
Vis à tête ronde de 4 x 20 mm
Tornillos de cabeza redonda de 4 x 20 mm x 4
2
CVP-59S:
Montage
CVP-59S:
Montaje
○○○○○○○○○○○○○○○○○○○○○○○○○
○○○○○○○○○○○○○○○○○○○○○○○○○
• Nous ne vous conseillons pas d’essayer d’assembler le Clavinova
seul. Toutefois, ce travail peut être facilement exécuté par deux
personnes.
• No le recomendamos que monte la Clavinova usted solo. Sin
embargo, el trabajo podrá realizarse con más facilidad entre dos
personas solamente.
• N’utilisez que les vis fournies ou des vis ayant exactement les
mêmes dimensions. Le fait d’utiliser des vis de dimensions incorrectes pourrait endommager l’instrument.
• Emplee sólo los tornillos suministrados u otros que sean exactamente del mismo tamaño especificado. El empleo de tornillos del
tamaño erróneo puede dañar el instrumento.
Z Ouvrez le carton et retirez toutes les pièces.
Z Abra la caja y extraiga todas las partes.
Les pièces indiquées sur l’illustration devraient toutes
se trouver dans le carton. Vérifiez qu’il n’en manque
aucune.
X Fixez les panneaux latéraux (D) au pédalier
(C)
Avant de poser le pédalier, détachez le cordon de la
partie inférieure du pédalier et déroulez-le.
Placez le pédalier sur les cales en bois fixées aux panneaux latéraux (D) et fixez-le en utilisant les quatre vis
à tête ronde 1 de 6 x 25 mm : deux vis de chaque
côté. Veillez à ce que les pédales et la partie qui dépasse des supports inférieurs soient dirigées dans le
même sens.
C Fixez le panneau central (B) aux panneaux
latéraux (D)
Le panneau central (B) doit être fixé aux ferrures verticales des panneaux latéraux (D) à l’aide des quatre vis
à tête ronde 2 de 4 x 20 mm, comme illustré. Assurez-vous que le panneau central est fixé sur le côté des
ferrures dirigé vers le pédalier
Al abrir la caja, encontrará las partes mostradas en la
ilustración de arriba. Compruebe y asegúrese de que
no falta ninguna de las partes requeridas.
X Monte los paneles laterales (D) en la caja de
pedales (C).
Antes de instalar la caja de pedales, desate y alargue el
cable enrollado unido a la parte inferior de la caja de
pedales.
Coloque la caja de pedales encima de bloques de madera colocados en los paneles laterales (D), y una usando los cuatro tornillos de cabeza redonda de 6 x 25 mm
1; dos tornillos en cada lado. Asegúrese de que los
pedales se extienden en la misma dirección que las
patas.
C Monte el panel central (B) en los paneles
laterales (D).
El panel central (B) debe enroscarse a las ménsulas
verticales de los paneles laterales (D) usando los cuatro
tornillos de cabeza redonda de 4 x 20 mm 2, como se
muestra en la ilustración. Asegúrese de que el panel
central queda unido al lado de las ménsulas orientado a
los pedales.
151
4
Danger Zone
Gefahrenzone
Zones dangereuses
Zona peligrosa
A
A
6 x 18 mm flat-head screws
Senkschrauben (6 x 18 mm)
Vis à tête plate de 6 x 18 mm
Tornillos de cabeza plana de
6 x 18 mm
3
D
D
V Install the main unit (A).
Gently place the main unit (A) on the side panels (D)
with the screws on its bottom panel (toward the rear of
the main unit) just in front of the grooves in the brackets located at the top of the side panels. Then slide the
main unit to the rear until it stops. WATCH YOUR
FINGERS WHEN DOING THIS!!
Align the holes on the bottom panel of the main unit
with the holes in the brackets on the side panels (also
center the main unit to produce an equal clearance on
the left and right sides, as shown in the illustration),
then screw in and securely tighten the six 6 x 18mm
flat-head screws 3 (three screws for each side of the
main unit).
* Keep your fingers away from the area marked “Danger Zone” in
the illustrations when lowering the main keyboard unit onto the
stand assembly.
B Connect the pedal cord.
Pass the pedal cord through the two cord holders on the
side panel. Insert the connector on the free end of the
cord into the corresponding socket on the underside of
the main unit. Make sure that the protruding clip on the
connector is facing the rear of the main unit. Close the
clips of the two cord holders to keep the cord firmly in
place.
152
A
V Die Haupteinheit (A) montieren.
Setzen Sie die Haupteinheit (A) vorsichtig so auf die
Seitenwände (D), daß die Schrauben an ihrer Unterseite (hinten) vor den oberen Halterungen an den
Seitenwänden zu liegen kommen. Schieben Sie die
Haupteinheit dann nach hinten, bis die Schrauben bis
zum Anschlag in den Halterungsschlitzen sitzen. VORSICHT! KLEMMEN SIE SICH DABEI NICHT
DIE FINGER EIN!
Bringen Sie nun die Bohrungen in den beiden seitlichen Halterungen mit den Bohrungen an der Unterseite
der Haupteinheit zur Deckung (achten Sie auch darauf,
daß die Haupteinheit mittig positioniert ist, d.h. links
und rechts gleichviel übersteht, wie in der Abbildung
gezeigt), und schrauben Sie die Haupteinheit dann mit
den sechs Senkschrauben (6 x 18 mm) 3 fest (jeweils
drei Schrauben links und rechts).
* Halten Sie beim Aufsetzen der Haupteinheit auf die Ständerbaugruppe von dem in der Abbildung mit “Gefahrenzone” gekennzeichneten Bereich fern.
B Das Pedalkabel anschließen.
Führen Sie das Pedalkabel durch die beiden
Kabelhalter an der Seitenwand. Schließen Sie das Kabel danach an die Buchse auf der Unterseite der Haupteinheit an. Der Stecker muß mit der Führungsnase in
Richtung Rückseite (der Haupteinheit) in die Buchse
gesteckt werden. Drücken Sie nun noch die Klemmen
der Kabelhalter fest an, damit das Kabel sicher gehalten wird.
5
A
A
D
Cord holder
Kabelhalter
Support de cordon
Soporte de cable
V Posez le clavier (A)
C
V Monte la unidad principal (A).
Placez le clavier (A) sur les panneaux latéraux (D),
avec les vis de son panneau inférieur (situées vers l’arrière du clavier) placées immédiatement derrière les
fentes des ferrures situées à la partie supérieure des
panneaux latéraux (D), puis faites glisser le clavier vers
l’avant jusqu’à ce qu’il vienne en butée. FAITES ATTENTION A VOS DOIGTS EN EXECUTANT
CETTE OPERATION !!
Alignez les trous du panneau inférieur du clavier sur
les trous des ferrures des panneaux latéraux (centrez
également le clavier de manière à avoir un jeu identique de chaque côté comme montré sur l’illustration)
puis posez et serrez à fond les six vis à tête plate 3 de
6 x 18 mm (trois vis de chaque côté du clavier).
Coloque con cuidado la unidad principal (A) en los
paneles laterales (D) con los tornillos de su panel inferior (hacia la parte trasera de la unidad principal) junto
delante de las ranuras situadas en la parte superior de
los paneles laterales. Entonces, deslice la unidad principal hacia atrás hasta que haga tope. ¡CUANDO LO
HAGA, TENGA CUIDADO CON LOS DEDOS!
Alinee los orificios del panel inferior de la unidad principal con los de las ménsulas de los paneles laterales
(centre también la unidad principal para producir una
holgura igual en los lados izquierdo y derecho, como se
muestra en la ilustración), y entonces enrosque y apriete bien los seis tornillos de cabeza plana de 6 x 18 mm
3 (tres tornillos para cada lado de la unidad principal).
* Lorsque vous abaissez le clavier sur son support, ne placez
pas les mains dans les zones marquées “Zones dangereuses”
sur l’illustration.
* Mantenga apartados los dedos de la parte marcada con “Zona
peligrosa” en las ilustraciones cuando baje la unidad del teclado principal al conjunto del soporte.
B Connectez le cordon du pédalier
Faites passer le cordon du pédalier dans les deux supports de cordon situés sur le panneau latéral. La prise
doit être branchée au connecteur correspondant situé à
la partie inférieure du clavier. Assurez-vous que la
partie en saillie de la prise est dirigée vers l’arrière du
clavier. Fermez soigneusement les deux supports pour
maintenir le cordon bien en place.
B Conecte el cable de pedales.
Pase el cable de pedales por los dos soportes de cable
del panel lateral. Inserte el conector del extremo libre
del cable en el receptáculo correspondiente de la parte
inferior de la unidad principal. Asegúrese de que el
conector deben insertarse con el retenedor saliente
orientado a la parte trasera de la unidad principal.
153
6
A
220
240
110
● A voltage selector is provided in some areas.
● Spannungswähler
(nur in bestimmten Verkaufsgebieten)
● Un sélecteur de tension est prévu pour
certaines régions
● El selector de tensión está provisto para
ciertos destinos.
127
N Voltage Selector
Before connecting the AC power cord, check the setting of the voltage selector which is provided in some
areas. To set the selector for 110V, 127V, 220V or
240V main voltages, use a “minus” screwdriver to rotate the selector dial so that the correct voltage for your
region appears next to the pointer on the panel. The
voltage selector is set at 240V when the unit is initially
shipped.
After the proper voltage has been selected connect the
AC power cord. A plug adaptor may be also provided
in some areas to match the pin configuration of the AC
wall outlets in your area.
M Set the adjuster.
For stability, an adjuster is provided on the bottom of
the pedal box (C). Rotate the adjuster until it comes in
firm contact with the floor surface. The adjuster ensures stable pedal operation and facilitates pedal effect
control. If the adjuster is not in firm contact with the
floor surface, distorted sound may result.
• After assembling the Clavinova, check once more to make sure
that all screws have been securely fastened.
• If the stand leans to the side, makes unusual noises, or otherwise
seems unstable during use, check and tighten all screws while
following the assembly instructions given above.
N Den Spannungswähler einstellen.
Bevor Sie nun das Netzkabel anschließen, müssen Sie
den Spannungswähler (falls vorhanden) auf die örtliche
Netzspannung einstellen. Zum Verstellen drehen Sie
den Spannungswähler mit einem
Schlitzschraubendreher, bis der richtige Spannungswert
(110, 127, 220 oder 240) an der Pfeilmarkierung steht.
Bei der Auslieferung werden alle Instrumente mit
Spannungswähler auf “240” voreingestellt.
Nachdem Sie den Spannungswähler richtig eingestellt
haben, können Sie nun das Netzkabel anschließen. In
manchen Gebieten wird ein Steckerdapter mitgeliefert,
um den Anschluß an die evtl. unterschiedlich geformte
Steckdose zu ermöglichen.
M Die Pedalstütze einstellen.
Für bessere Standfestigkeit ist unter dem Pedalkasten
(C) eine verstellbare Pedalstütze vorgesehen. Nachdem
Sie das Clavinova an seinem festen Standplatz aufgestellt haben, drehen Sie diese Stütze heraus, bis sie fest
auf dem Boden steht. Die Stütze sorgt beim Spielen für
präzise Pedalbetätigung. Wenn die Pedalstütze nicht
fest auf dem Boden aufsteht, können
Klangverzerrungen auftreten.
• Vergewissern Sie sich nach Zusammenbau und Aufstellung des
Clavinova noch einmal davon, daß alle Schrauben fest angezogen
sind.
• Wenn das Instrument schief steht, komische Geräusche erzeugt
oder sich beim Spielen wackelig anfühlt, prüfen Sie gemäß den
obigen Anweisungen, ob das Instrument richtig zusammengebaut
wurde, und ziehen dabei die einzelnen Schrauben noch einmal
nach.
154
7
C
N Sélecteur de tension
Avant de connecter le cordon d’alimentation, vérifiez
le réglage du sélecteur de tension qui est prévu pour
certaines régions. Pour régler le sélecteur sur 110 V,
127 V, 220 V ou 240 V, utilisez un tournevis à lame
plate pour tourner le cadran du sélecteur afin de mettre
l’indication correspondant à la tension de votre région
vis à vis du repère triangulaire situé sur le panneau. Le
sélecteur de tension est réglé sur 240 V au départ
d’usine.
Une fois que vous avez réglé le sélecteur de tension,
connectez le cordon d’alimentation. Un adaptateur de
prise peut également être fourni dans certaines régions
pour pouvoir brancher le cordon à la prise secteur murale.
M Réglez la hauteur du pédalier
Pour assurer la stabilité, un dispositif de réglage a été
prévu à la partie inférieure du pédalier (C). Tournez ce
dispositif jusqu’à ce qu’il soit en contact ferme avec la
surface du sol. Ce dispositif assure la stabilité du pédalier lors de son utilisation et facilitent la commande au
pied des effets. Si ce dispositif n’est pas en contact
ferme avec le sol, il pourra se produire une distorsion
du son.
• Après avoir monté le Clavinova, vérifiez de nouveau que toutes les
vis sont bien serrées à fond.
• Si l’instrument penche d’un côté, s’il fait un bruit inhabituel, ou s’il
paraît instable lorsque vous l’utilisez, vérifiez que vous l’avez assemblé correctement et que toutes les vis sont bien serrées en
suivant les instructions de montage données ici.
N Selector de tensión
Antes de conectar el cable de alimentación de CA,
compruebe el ajuste del selector de tensión que se incorpora para ciertos destinos. Para ajustar el selector a
110V, 127V, 220V ó 240V de la red de alimentación,
emplee un destornillador de cabeza recta “-” para girar
el selector de modo que la tensión correcta de su zona
aparezca al lado del indicador del panel. El selector de
tensión se ajusta a 240V cuando la unidad sale de fábrica.
Después de haber seleccionado la tensión correcta,
enchufe el cable de alimentación. En algunas zonas
puede suministrarse también un adaptador para adaptar
la configuración de las patillas de los tomacorrientes de
CA de su localidad.
M Ajuste los reguladores.
Para más estabilidad, se proporciona un regulador en la
parte inferior de la caja de pedales (C). Gire el regulador hasta que haga buen contacto con la superficie del
piso. El regulador asegura una operación estable de los
pedales y facilita el control de los efectos con los pedales. Si el ajustador no está en buen contacto con la
superficie del piso, el sonido podría distorsionarse.
• Después de haber montado la Clavinova, compruebe una vez más
que todos los tornillos se hayan apretado bien.
• Si el soporte se inclina a un lado, hace ruidos anormales, o parece
inestable durante la utilización, compruebe y apriete todos los
tornillos siguiendo las instrucciones de montaje anteriores.
155
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in
this manual, meets FCC requirements. Modifications not expressly
approved by Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT: When connecting this product to accessories and/or
another product use only high quality shielded cables. Cable/s supplied
with this product MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC authorization to use
this product in the USA.
3. NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reasonable
level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.
This equipment generates/uses radio frequencies and, if not installed
and used according to the instructions found in the users manual, may
cause interference harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that interference will
not occur in all installations. If this product is found to be the source of
interference, which can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the
interference.
Utilize power outlets that are on different branch (circuit breaker or fuse)
circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the
antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type
cable.
If these corrective measures do not produce satisfactory results, please
contact the local retailer authorized to distribute this type of product. If you
can not locate the appropriate retailer, please contact Yamaha Corporation
of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena
Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT. The wires in this mains lead are coloured in accordance
with the following code:
BLUE
: NEUTRAL
BROWN
: LIVE
As the colours of the wires in the mains lead of this apparatus may not
correspond with the coloured makings identifying the terminals in your
plug proceed as follows:
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal
which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the
three pin plug.
CANADA
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B”
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS SET OUT IN THE RADIO INTERFERENCE REGULATION OF
THE CANADIAN DEPARTMENT OF COMMUNICATIONS.
LE PRESENT APPAREIL NUMERIQUE N’EMET PAS DE BRUITS
RADIOELECTRIQUES DEPASSANT LES LIMITES APPLICABLES
AUX APPAREILS NUMERIQUES DE LA “CLASSE B” PRESCRITES
DANS LE REGLEMENT SUR LE BROUILLAGE RADIOELECTRIQUE
EDICTE PAR LE MINISTERE DES COMMUNICATIONS DU CANADA.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
• This applies only to products distributed by Yamaha Canada Music Ltd.
• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
157
IMPORTANT SAFETY INSTRUCTIONS
INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,
AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.
WARNING- When using any electrical or electronic product, basic precautions should always be followed. These precautions include, but are not limited to, the following:
1.
Read all Safety Instructions, Installation Instructions,
Special Message Section items, and any Assembly Instructions
found in this manual BEFORE marking any connections, including connection to the main supply.
2.
Main Power Supply Verification: Yamaha products are
manufactured specifically for the supply voltage in the area
where they are to be sold. If you should move, or if any doubt
exists about the supply voltage in your area, please contact
your dealer for supply voltage verification and (if applicable)
instructions. The required supply voltage is printed on the
name plate. For name plate location, please refer to the graphic
found in the Special Message Section of this manual.
3.
This product may be equipped with a polarized plug
(one blade wider than the other). If you are unable to insert the
plug into the outlet, turn the plug over and try again. If the
problem persists, contact an electrician to have the obsolete
outlet replaced. Do NOT defeat the safety purpose of the plug.
4.
Some electronic products utilize external power supplies or adapters. Do NOT connect this type of product to any
power supply or adapter other than one described in the owners
manual, on the name plate, or specifically recommended by
Yamaha.
8.
This product was NOT designed for use in wet/damp locations and should not be used near water or exposed to rain. Examples of wet/damp locations are; near a swimming pool, spa, tub,
sink, or wet basement.
9.
This product should be used only with the components
supplied or; a cart, rack, or stand that is recommended by the
manufacturer. If a cart, rack, or stand is used, please observe all
safety markings and instructions that accompany the accessory
product.
10.
The power supply cord (plug) should be disconnected from
the outlet when electronic products are to be left unused for extended periods of time. Cords should also be disconnected when
there is a high probability of lightening and/or electrical storm
activity.
11.
Care should be taken that objects do not fall and liquids are
not spilled into the enclosure through any openings that may exist.
12.
Electrical/electronic products should be serviced by a
qualified service person when:
a. The power supply cord has been damaged; or
b. Objects have fallen, been inserted, or liquids have been
spilled into the enclosure through openings; or
c. The product has been exposed to rain; or
d. The product does not operate, exhibits a marked change
in performance; or
e. The product has been dropped, or the enclosure of the
product has been damaged.
5.
WARNING: Do not place this product or any other
objects on the power cord or place it in a position where anyone could walk on, trip over, or roll anything over power or
connecting cords of any kind. The use of an extension cord is
not recommended! If you must use an extension cord, the
minimum wire size for a 25' cord (or less) is 18 AWG. NOTE:
The smaller the AWG number, the larger the current handling
capacity. For longer extension cords, consult a local electrician.
6.
Ventilation: Electronic products, unless specifically
designed for enclosed installations, should be placed in locations that do not interfere with proper ventilation. If instructions for enclosed installations are not provided, it must be
assumed that unobstructed ventilation is required.
13.
Do not attempt to service this product beyond that described in the user-maintenance instructions. All other servicing
should be referred to qualified service personnel.
14.
This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing
sound levels that could cause permanent hearing loss. DO NOT
operate for a long period of time at a high volume level or at a
level that is uncomfortable. If you experience any hearing loss or
ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period
before damage occurs.
15.
7.
Temperature considerations: Electronic products should
be installed in locations that do not significantly contribute to
their operating temperature. Placement of this product close to
heat sources such as; radiators, heat registers and other devices
that produce heat should be avoided.
Some Yamaha products may have benches and/or accessory
mounting fixtures that are either supplied as a part of the product
or as optional accessories. Some of these items are designed to be
dealer assembled or installed Please make sure that benches are
stable and any optional fixtures (where applicable) are well secured BEFORE using. Benches supplied by Yamaha are designed
for seating only. No other uses are recommended.
PLEASE KEEP THIS MANUAL
92-469-2
M.D.G., EMI Division © 1995 Yamaha Corporation
VT47770 507POCP4.3-02B0 Printed in Japan
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising