advertisement
User Instruction Manual
ZT-1017-VS
ZT-6000-VS
FOR SALES, SERVICE OR TECH SUPPORT CALL:
1800-BUY-RIVET or 1-800-289-7483
S
AFETY
C
ONTENTS
Page 3 Safety
Specifications
Preparing the tool for service
Jaw Cleaning Procedure / Jam Remedy
Proper Jaw Pusher Selection
Air supply
Preventive Maintenance / Service
Parts
Daily
Weekly
Head Assembly
Pneumatic Piston Assembly
Oil Change/Replacement Procedure
Valve Spool Assembly
Trigger
Page 3
Page 4
Page 5
Page 5
Page 6
Page 6
Page 6
Page 7
Page 7
Page 8
Page 8
Page 9
Page 12
Page 13
Schematic
Part List
Material Safety Data Sheet
Page 8
Oil MSDS
Troubleshooting
2
Â
D
O NOT USE OUTSIDE DEISNG INTENT OR WITH EQUIPMENT THAT IS NOT RECOMMENDED BY THE MANUFACTURER
.
Â
A
LWAYS DISCONNECT THE AIR SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE OR ADJUSTMENT
/
FITTING OF NOSE EQUIPMENT
Â
D
O NOT OPERATE A TOOL THAT IS DIRECTED TOWARDS ANY PERSON
(
S
)
OR WITH THE MANDREL CATCHER OFF THE TOOL
Â
A
LL MODIFICATIONS CARRIED OUT ON THE TOOL WITHOUT EXPRESS WRITTEN CONSENT OF THE MANUFACTURER SHALL BE DONE
SO AT THE CUSTOMERS ’ SOLE RESPONSIBILITY
Â
R
EFER TO THIS MANUAL BEFORE ATTEMPTING ANY MAINTENANCE OPERATION
.
DO NOT DISASSEMBLE THIS TOOL BEFORE
RFERING TO THIS MANUAL
.
Â
A VOID EXCESSIVE CONTACT WITH HYDRAULIC OIL , AS SOON AS POSSIBLE WASH HANDS THOROUGHLY
Â
D
O NOT EXCEED
7
BAR
/ 100
PSI INLET PRESSURE
,
THE USE OF A PRESSURE REGULATOR IS HIGHLY RECOMMENDED
Â
I
NSPECT THE TOOL USING PREVENTITIVE MAINTENANCE TECHNIQUES AT REUGULARLY SCHEDULED INTERVALS
.
INSPECT FOR
DAMAGE AND FUNCTION BY TRAINED COMPETANT PERSONEL
.
REPLACE THE PNEUMATIC CYLINDER HOUSING OR HYDRAUILIC
CYLINDER HOUSING WHERNEVER THERE IS EVIDANEC OF IMPACT DAMAGE
,
CHIPPING
,
OR CRACKING
.
Â
WEAR SAFETY GLASSES AND ADOPT FIRM FOOTING DURING OPERATION
.
S
PECIFICATIONS
The specifications and information contained in this manual are applicable only to the tool with which it was supplied. Industrial Rivet & Fastener Co reserve the right to make any changes without notice as part of
Industrial Rivet & Fastener Co policy of continuous improvement.
S PECIFICATIONS FOR ZT -8000 R IVET T OOL
Air Pressure Min/Max 90 psi Max.
Bore Nom. 10
Stroke Minimum 17
Pull Force @5.5 bar/80psi 2,248
Cycle Time
Noise Level
Weight
Hydraulic Oil
Approximately
Less than
1.2
125
4.3
Mobil DTFE 24
3
P
REPARING THE TOOL FOR SERVICE
1
2
.
.
.
.
3 .
.
.
4
.
.
.
.
.
Inspect for damage
Connect the tool to the air supply
Choose and securely install the applicable nose piece for the rivets you wish to apply.
Adjust the vacuum until rivet is held in the nose piece while tool is pointed downward.
a. Adjust vacuum by rotating the small brass valve located at reat of the tool inside the mandrel catcher using the wrench provided.
5
6
.
.
.
.
.
.
Bring the tool and the rivet into the application hole. Insure the rivet head flat onto surface
Fully Actuate the trigger. The tool will cycle and set the rivet while ejecting the nail into the
7 .
.
.
rear mandrel catcher.
Empty catcher when at 50% capacity
4
J
AW CLEANING PROCEDURE
/
JAMMED GUN REMEDY
1. Disconnect tool from air supply
2. Leaving the nose piece attached, remove the nose case 26 using a wrench by loosening locknut 25 and then by loosening 26 at the wrench point just below the nose piece.
3. Fit two wrenches to the tool keeping the nut 19 & 20 towards the piston stationary while unscrewing the jaw casing 24. It is important that you only unscrew the nut closest to the jaws (jaw casing) 24. DO NUT ADJUST LOCKNUT 18 and 19.
4. Take care during removal as this jaw casing is spring loaded and contains 2 small jaws 23, a jaw pusher 22, and a spring 21. Do not lose these pieces.
5. Once removed, remove the mandrel from the jaws, discard mandrel.
6. Clean Jaws 23 with a mineral spirit then and coat outside of jaws (outside only) with a light layer of white lithium grease. Be sure to coat the outside of the jaws only.
7. Replace jaws into jaw case 23, followed by jaw pusher 22, and spring 21.
8. Re-apply jaw case 24 securely to the tool using a wrench.
9. Reapply the nose case 26 securely to the tool
10. Reattach air supply. Actuate tool without rivet. Check Function.
11. Once comfortable, Apply Rivets.
P
ROPER
J
AW
P
USHER
S
ELECTION
The proper Jaw Pusher must be used so that the rivets flow through the tool when the vacuum system is activated.
If the wrong jaw pusher is used during riveting, it is possible that two rivets can get stuck alongside each other jamming the gun. Another failure could happen when the jaw pusher is too large for the rivet causing the vacuum system to be ineffective due to the lack of air/mandrel resistance. Be sure to use the proper Jaw Pusher!
1/8” & 3/32” Rivets – Silver Jaw Pusher
3/16” & 5/32” Rivets – Black Jaw Pusher
5
A
IR
S
UPPLY
•
The rivet tool is powered by compressed air at an optimum pressure of 5.5 bar (80 psi)
•
The use of a pressure regulator filter/lubricator unit within 3 meters of the tool is highly recommended to extend the life of the tool.
Dirt and/or water in the air supply can seriously impact the performance and durability of the tool; damage to the tool caused by contaminated air supply is not covered under warranty
M
AINTENANCE
In order to maintain the tool in a safe working order it is important to carry out regular maintenance as prescribed by the manufacturer. A thorough inspection replacement of all seals within the tool should be carried out after 500,000 placings or annually, whichever is the sooner. Item numbers in parentheses refer to assembly drawing part numbers
Daily
Check for air leaks. Any damaged hoses should be replaced
Lubricate the tool by pouring a 1 drop of light lubricating oil into the air inlet on the tool
If there is no pressure regulator, bleed the airline to clear it of accumulated dirt or water before connecting the air hose to the tool. If there is a filter, drain it.
Check for proper nose piece use depending on the size of the rivet.
Remove front jaw nose assembly and inspect for cracks or other damage to front and rear of the nose piece. Replace if necessary.
Insure that rotary valve for the vaccum on the mandrel collection unit is correctly adjusted for fastener retention
Weekly
Carry out procedures as per daily maintenance instructions above
Clean and inspect the jaws for signs of damage or wear (groove running through the jaw serrations). Follow the instructions on page 4 for cleaning of jaws. Reassemble the tail jaws with a light coating of grease on the outer face that contacts the jaw housing. Do not allow grease to contaminate the grooved inner face of the jaws as mandrel slippage may result.
Monthly
Carry out procedures as per daily maintenance instructions above
Check and replace cylinder bodies if there are signs of damage or cracks.
6
M
AINTENANCE
Follow the instructions below to perform annual service and replacement of seals, item numbers in parentheses refer to assembly drawing part numbers on page 8.
Head Assembly
Replace Seals 5, 6, 7, 9 and Return Spring 8. When seals are replaced apply a very light coating of white lithium grease to the hydraulic body and to the surface of the o-rings.
Pneumatic Piston Assembly
Replace 36 & 34 then proceed to oil filling procedure.
7
M
AINTENANCE
Oil Filling Procedure
Turn the tool upside down. Unscrew 4 socket screws and remove air piston cover. Remove air cylinder and hydraulic piston rod until oil is exposed. Empty oil by turing the tool upside down and draining into a suitable container making best efforts to keep the tool handle and other parts from oil contamination. After oil is drained, remove excess oil from top surface. Add new oil (Mobile DTE 24 light hydraulic oil is preferred) by pouring into the hydraulic tube as shown. Add enough until about
1/8” below the top seal. Make every attempt to avoid the introduction of air or bubbles into the oil as its being poured. Adding the oil slowly and close to the edge of the tube will prevent this. Reassemble the tool in reverse order.
IMPORTANT: DISCONNECT THE TOOL FROM THE AIR SUPPLY OR SWITCH OFF AT VALVE (55).
REMOVE NOSE ASSEMBLY OR SWIVEL HEAD COMPONENTS. All operations should be carried out on a clean bench, with clean hands in a clean area. Ensure that the new oil is perfectly clean and free from air bubbles. Care MUST be taken at all times, to ensure that no foreign matter enters the tool, or serious damage may result.
Valve Spool Assembly
Send into authorized repair center for service.
8
M
AINTENANCE
Trigger
Inspect trigger pin valve by insuring 56 has not come loose. The proper depth should be just under the valve stem.
If adjustment is necessarym using a fork wrench or tire valve tool, screw the trigger pin 56 into the valve stem. A very small amount of loctite243 is ok around the threaded portion only.
If the trigger still fails, remove the trigger pin assembly from the valve stem and inspect the seal around the trigger pin for damage. If damaged, purchase a replacement part. Reassemble according to the previous step.
#55 & #56
9
SCHEMATIC
10
11
PARTS LIST
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Index
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
214302
612303
612314
918106
612105
OR2025
107108
OR1419
BR1419
107401
107501
107503
819502
107502
918505
107403
107404
107408
OR0509
OR0711
OR1014
107409
107407
107406
CH0809
103225
SW0508
HN1032
612714
OR0306
Part #
107101
OR1823
BR1823
107301
107302
OR2431
BR2431
214309
OR0609
107123
OR1621
OR0913
612115
612114
OR3034
214102
214306
214305
OR1417
214308
Description
Hydraulic Section
O-Ring (2)
Back-Up Ring
Hydraulic Plunger
Plug
O-Ring (2)
Back-Up Ring
Return Spring (Y)
O-Ring
Vacuum Tube Ass'y
O-Ring
O-Ring
Lock Nut
Vacuum Regulator
O-Ring
Rear Gland
Nut
Jaw Housing Coupler
O-Ring
Spring
Jaw Pusher
Jaw “M” (2)
Jaw Hosing
Lock Nut
Head
O-Ring (2)
Tube
O-Ring (2)
Back-Up Ring
Upper Cover
Plunger Rod
Front Head Disc
Packing Ring
Lower Plate
Bumper Ring
Air Cylinder Body
Rubber Washer (2)
Valve Stem
O-Ring (2)
O-Ring
O-Ring (3)
Inlet Plug (2)
Exhaust Plug
Muffler
Retaining Ring
Set Screw (4)
Spring Washer (4)
Nut (4)
Washer (3)
O-Ring (2)
612705
612706
612708
107901
107902
612905
918905
612901
819904
819901
819912
214312
612902
Part #
612712
612713
612711
107602
107601
612717
107201
107107R
107107L
ST0310
PW0306
612704
63.
64.
65.
66.
67.
68.
69.
70.
71.
72.
Index
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
61-1
62.
Description
Swivel
Socket
Cap (2)
Air Relieve Valve
Hose Joint
Socket (Lower)
Trigger
Plastic Grip-Right
Plastic Grip-Left
Screw (4)
Washer
Nose Piece 1/8" (3.2mm) (opt.)
Nose Piece 5/32" (4.0mm) (opt.)
Nose Piece 3/16” (4.8mm)
Nose Piece 1/4" (6.4mm)
Air Hose-short
Air Hose-Long
Deflector
Multi-Wrench (A)
Multi-Wrench (B)
Front Cap (opt.)
Collection Bottle (opt.)
Rear Cap (opt.)
Jaw Pusher ( For all rivets under size 3/16” ) (opt.)
Guide Hose (opt.)
OIL MATERIAL SAFETY DATA SHEET
(
MSDS
)
Priming is ALWAYS necessary after the tool has been dismantled and prior to operating. It may also be necessary to restore the full stroke after considerable use, when the stroke may be reduced and fasteners are not fully placed by one operation of the trigger
Oil Details
The recommended oil for priming is Mobil DTE 24 or Hyspin VG32 available in 0.51 or one gallon containers, or, you can use 30W hydraulic oil. Please see safety data below.
Mobil DTE 24 or Hyspin VG 32 Oil Safety Data
First Aid
SKIN:
Wash thoroughly with soap and water as soon as possible. Casual or short term contact requires no immediate attention.
INGESTION:
Seek medical attention immediately. DO NOT induce vomiting.
EYES:
Irrigate immediately with water for several minutes. Although NOT a primary irritant, minor irritation may occur following contact.
Fire
Flash point 232°C. Not classified as flammable.
Suitable extinguishing media: CO
2
, dry powder, foam or water fog. DO NOT use water jets.
Environment
WASTE DISPOSAL: Through authorized contractor to a licensed site. May be incinerated. Used product may be sent for reclamation.
SPILLAGE: Prevent entry into drains, sewers, and water courses. Soak up with absorbent material.
Handling
Wear eye protection, impervious gloves (e.g. of PVC) and a plastic apron. Use in well ventilated area.
Storage
No special precautions.
Priming Kit
To enable you to follow the priming procedure opposite, you will need to obtain a priming kit:
PRIMING KIT: ZRT-HO
PART NO
HO
ZRT
DESCRIPTION
Mobil DTE 24
Refill Bottle
12
T
ROUBLESHOOTING
Item numbers in parentheses refer to assembly drawing part numbers on page 9.
Remedy
More than one operation of the trigger needed to place fastener
Tool will not grip stem of fastener
Jaws will not release broken stem of fastener
Jammed Gun / Cannot feed next fastener
Slow cycle
Tool fails to operate
Fastener fails to break
Insufficient Vacuum
Pressure
Air leak
Insufficient air pressure
Lack of lubrication
Worn or broken jaws
Low oil level or air in oil
Build up of dirt inside the nose assembly
Worn or broken jaws
Build up of dirt inside the nose assembly
Loose jaw housing
Weak or broken spring in nose assembly
Incorrect component in nose assembly
Rotary valve incorrectly adjusted
Build up of dirt inside the nose assembly
Jaw housing, nose tip or nose casing not properly seated
Weak or broken spring in nose assembly
Air or oil leak
Low oil level or air present in oil
Broken stems jammed inside tool
Rotary valve incorrectly adjusted
Lack of lubrication
Low air pressure
Build up of dirt inside the nose assembly
No air pressure
Damaged trigger valve
Loose pneumatic piston cover
Loose stem collector
Insufficient air pressure
Fastener outside tool capability
Low oil level or air present in oil
Insufficient Air Pressure
Improper Vacuum Pressure Adjustment
Wrong Jaw Pusher
Tighten joints or replace components
Adjust air pressure to within specification
Lubricate tool at air inlet point
Fit new jaws
Prime tool
Service nose assembly
Fit new jaws
Service nose assembly
Tighten against locking ring
Fit new spring
Identify and replace
Read ‘Operating Procedure’
Service nose assembly
Tighten nose assembly and adjust if necessary
Fit new spring
Tighten joints or replace components
Prime tool
Empty mandrel collector
Check if jaw pusher is correct
Adjust air pressure to within specification
Adjust as in ‘Operating Procedure’
Lubricate tool at air inlet point
Adjust air pressure to within specification
Service nose assembly
Connect and adjust to within specification
Replace
Tighten Socket Screws
Tighten
Adjust air pressure to within specification
Use more powerful tool
Contact Industrial Rivet
Prime/Re-Fill oil
Set to 90psi
See “putting the tool into service” for proper adjustment
See “proper jaw pusher selection”
13
Warranty Statement:
Industrial Rivet & Fastener Co. Inc. and Zipp Tools (hereinafter “IRF”), hereby warrants to the initial retail customer and original distributor (“Warrantee”) only that its products will be free from defects in material and workmanship for a period of 1 year from the purchase date, provided that the products are used in accordance with “IRF’s” instructions as to maintenance, operation and use.
The said warranty does not extend to goods subjected to misuse, neglect, accident or improper installation or maintenance or which have been altered or repaired by anyone other than the seller or its authorized agents.
The warrantee’s only remedy and IRF’s only obligation in the event of a defect or failure in the products, is that IRF, at its sole option, repair, replace or rework the products, but in no case shall the cost of the foregoing exceed the invoice price of the products.
This warranty shall be void if any person seeking to make a claim for defective or failed products fails to notify IRF within 30 days of receipt of evidence that the product is defective or has failed, or if said person fails to provide IRF with such evidence as is reasonably requested concerning the effect or failure, including without limitation, evidence of the date of purchase and date of installation.
This warranty is in lieu of all other warranties, expressed or implied, including merchantability, or fitness provided for herein. Under no circumstance shall IRF be liable for incidental or consequential damages arising from the defect or failure in its products.
Seller’s sole obligation under the foregoing warranty will be limited to, at Seller’s option, repair or replacement of the tool (and shipping to the buyer with transportation charges paid to any place within the contiguous 48 states). Returned goods will be evaluated by our warranty repair department and a conclusion will be determined and classified as:
a) Warranty Repair (free of charge)
b) Abuse /Neglect (bench fee and/or hourly rate)
c) Maintenance (Flat Fee)
Price Schedule as of 1/1/2007
Bench Fee: $55.00
Hourly Rate: $55.00 per hour
Flat Fee:
Level 1 - Adjustments and light repair $35.00 + parts
Level 2 – Maintenance, Oil Change $95.00 + parts
Level 3 – Overhaul, complete disassembly, change all seals $155.00 + parts
If inspection by the seller of returned goods shows no breach of the forgoing warranty, Seller’s regular conditioning charges (as stated above) apply. Upon this conclusion we will either repair the tool at no cost to you and return it postage paid, or call you to inform you of the repair cost. The repair will need to be approved in writing before any work is performed.
A comprehensive tool service and repair program, for details contact your local area sales representative or call:
Industrial Rivet & Fastener Co.
200 Paris Ave
Northvale, NJ 07647
1-800-BUY-RIVET
14
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement