User manual | Product Summary

Document Number: 466-1534 Rev. C
April 2000
8362G12A.DS4
Use the indoor motion sensor to protect locations where
door/window sensors are impractical or not needed. For
example, use a motion sensor to protect large areas or open
floor plans. Motion sensors also provide backup protection
for door/window sensors.
Use the outdoor motion sensor to identify motion in a protected outdoor area. Detected motion in this protected area
can sound chimes or turn on outside lights.
❑
❑
❑
❑
Note
Do not use outdoor motion sensors for intrusion
protection.
The wireless motion sensor includes the following features:
❑
❑
❑
❑
❑
❑
❑
35 feet by 40 feet coverage area for standard and
optional animal alley lenses
Masking kit provided to block portions of the coverage
area
Three minute transmitter lockout time after an alarm
that helps extend battery life
Cover-activated tamper (optional wall-activated tamper
is included)
Supervisory signals transmitted every 64 minutes to the
control panel
Sensor low battery reports (trouble) to the control panel
Field-selectable sensitivity options
Indoor Installation Guidelines
Use the following guidelines for installing indoor motion
sensors.
❑
❑
If possible, locate sensors within 100 feet of the panel.
While a transmitter may have a range of 500 feet or
more out in the open, the environment at the installation site can have a significant effect on transmitter
range. Sometimes a change in sensor location can help
overcome adverse wireless conditions.
The recommended mounting height is 7 1/2 feet, but
the sensor can be mounted from 5 to 8 feet high in the
corner of the area you want to protect. See the animal
ITI® Indoor and Outdoor PIR Motion Sensors
1061G37A.DS4
Installation Instructions
Product Summary
A motion sensor (passive-infrared or PIR) detects movement within a specific area by sensing the infrared energy
emitted from a body as it moves across the sensor’s field of
view. When this motion is detected, the sensor transmits an
alarm signal to the control panel.
ITI Part No. 60-639-95R, 60-639-95R-OD,
60-639-43-EUR, 60-639-43-EUR-OD
❑
❑
❑
❑
❑
alley lens guidelines for mounting the optional animal
alley lens. Higher mounting provides better range (up
to 35 feet), and lower mounting provides better protection close to the motion sensor (see Figures 2 and 3).
The optional swivel mount (part #60-737) can be used
for difficult mounting locations.
Position the sensor to protect an area where an intruder
would be most likely to walk across the detection pattern (see Figure 1).
Mount the motion sensor on a rigid surface which is
free from vibrations.
Do not aim the sensor at windows, fireplaces, air conditioners, area heaters, forced air heating vents, or place
it in direct sunlight. Sudden changes in temperature
may trigger a false alarm from these devices.
Do not mount the sensor near duct work or other large
metallic surfaces which may affect the RF signals (see
RF Testing). Actual acceptable transmitter range
should be verified for each installation.
Mount the sensor permanently on a flat wall or in a corner. Do not set it on a shelf.
Windows should be closed in any area which has an
armed motion sensor.
A pet will trigger a motion sensor. See animal alley
lens guidelines to use a motion sensor when pets are
present.
Mount the motion sensor on an insulated, outside wall
facing in.
Position the sensor so it faces a solid reference point,
like a wall.
Outdoor Installation Guidelines
Use the following guidelines for installing outdoor motion
sensors.
❑
❑
❑
❑
❑
The outdoor motion sensor should be used for outdoor
applications where the temperature does not exceed a
range from 10° to 120° F.
Do not use outdoor motion sensors for intrusion protection since any human, pet, or heated mechanical motion
such as an automobile can activate the sensor.
Follow the indoor motion sensor installation guidelines
except for the last four items.
Do not aim the sensor at objects that may be heated
excessively by the sun, such as black top or dark colored objects.
Do not aim the sensor at foliage or shrubbery which has
a dark background.
1
Indoor Motion Sensor
❑
❑
The housing is water-resistant but not water-proof.
Mount the sensor underneath eaves or porch coverings
to prevent over exposure to rain, ice, and direct sunlight.
The sensor’s coverage area is shown in Figures 2 and 4.
and animal alley lens and the outdoor motion
sensor’s lens.
0m
8 ft
SIDE VIEWS (Indoor Motion Sensor Standard Lens)
11 ft
7 1/2 FOOT MOUNTING HEIGHT
2.4 m
4 ft
1.2 m
0m
35 ft
0 ft
0 ft
0m
8 ft
5 FOOT MOUNTING HEIGHT
11 ft
2.4 m
1.2 m
4 ft
0m
35 ft
0 ft
0 ft
8362G09B.DS4
Person walking across detection path
Figure 3. Side view show the differences in the coverage
area when using the indoor motion sensor’s standard lens mounted at different heights.
8362G04B.DS4
Figure 1. Overhead (Bird’s Eye View) Detection Path
SIDE VIEW INDOOR MOTION SENSOR ANIMAL ALLEY LENS
FLUSH MOUNT
11 ft
0m
2.4 m
8 ft
1.2 m
4 ft
0m
20 ft
TOP VIEW
11 m
6m
0m
35 ft
0 ft
8362G10C.DS4
10 ft
3m
0 ft
0m
20 ft
3m
20 ft
0 ft
6m
35 ft
8362G11A.DS4
Figure 4. Shows the side view of the indoor motion sensor’s animal alley lens when the flush-mount
position is used. The outdoor motion sensor’s
lens also has this side view, however, its swivel
mount makes the viewing angle adjustable.
Indoor Motion Sensor
Mounting
The sensor can be flush-mounted, incline-mounted, or corner-mounted depending on the lens used (see Figure 5).
Also, the optional swivel mount (ITI #60-737) can be used
for difficult mounting locations.
Figure 2. This graph shows the top view of the lens coverage area, for the indoor motion sensor’s standard
2
ITI® Indoor and Outdoor PIR Motion Sensors
Indoor Motion Sensor
FLUSH MOUNT
CORNER MOUNT
5.
Mark the location of the required holes on the mounting surface.
6.
Use wall anchors and screws to secure into place.
Attach the sensor to the mounting plate.
7.
When testing is completed the PIR can be securely
attached to its mounting plate by screwing the smallest
enclosed screw into the hole at the top of the mounting
plate.
INCLINED MOUNT
MOTION SENSOR MOUNTED USING SWIVEL MOUNT
Lens Replacement
1.
To change the lens, first remove the sensor from its
mounting plate by depressing the button on the top of
the sensor.
2.
Remove the cover by depressing the two tabs on the top
and the one tab on the bottom of the sensor body and
sliding the cover off (see Figure 8).
3.
Remove the installed lens by gently placing pressure on
the lens from the outside of the lens.
4.
Replace with the appropriate lens by aligning its
notches with the appropriate tabs in the cover.
5.
Install the new lens with the smooth side facing out and
the grooved side facing in.
6.
Replace the cover and then replace the sensor in its
mounting plate.
8362G03B.DS4
Figure 5. Wall Mount Options: use the inclined position for
surface or corner mounting with the standard
lens. Use the flush position for surface or corner
mounting with the animal alley lens. The optional
swivel mount installation is also shown.
Use the following procedure to mount the sensor.
1.
2.
Remove the mounting plate by depressing the button
on the top of the sensor body. With the opposite hand
pull the mounting plate away from the body of the sensor.
Punch out the mounting holes that best fit your application. See Figure 5 for wall mount options. See also Figure 6 to determine which knockouts to use when
mounting the motion sensor. Use the lower-side holes
for corner mounting, or the lower-back holes for surface mounting with the standard lens.
3.
For applications with pets, use the upper mounting
holes and the optional animal alley lens.
4.
If you desire wall-tamper functionality, remove the
wall-tamper knockout (see Figure 6).
Animal Alley Lens Guidelines
The optional animal alley lens (part #60-709) provides protection in installations where pets move about freely. See
figures 2 and 4 for coverage.
❑
❑
❑
Note
The wall-tamper switch cannot be used when the sensor is swivel or corner mounted.
❑
❑
USE
WITH
ANIMAL ALLEY LENS
Allowed mounting height is between 3 and 5 feet.
Be sure to use the flush-mount position or the corner
mount position with the back of the PIR parallel to the
walls. Do not use the inclined mount position since this
would tilt the PIR’s field of view downward.
Position the sensor to have a clear line of sight across
the protected room.
For best results, install the sensor higher than the highest point that the pet might reach in the detection area.
If the detection area contains furniture or other objects
upon which the pet could climb or jump, either remove
these objects, mount the PIR a safe distance above
these objects, or mask these areas.
Setting the Sensitivity
The PIR is set to standard sensitivity at the factory. This
sensitivity is preferred for most applications and provides
the best immunity to false alarms.
WALL
TAMPER
KNOCKOUT
USE WITH
STANDARD LENS
CAUTION
High sensitivity should only be used in extremely quiet
environments where thermal transients are not
expected.
8362G01B.DS4
Figure 6. PIR Mounting Plate Knockouts
ITI® Indoor and Outdoor PIR Motion Sensors
3
Outdoor Motion Sensor
1.
Locate the sensitivity pins by first removing the mounting plate and the sensor cover as described in steps 1
and 2 of Lens Replacement process.
1.
Remove the sensor from its water resistant enclosure
by sliding the front cover upward until the sensor can
be removed.
2.
Remove the mounting plate of the sensor by depressing
the button on top of the sensor.
3.
Remove the front cover of the sensor by depressing the
two tabs on the top and the one tab on the bottom of the
sensor body and sliding the cover off (see figure 8)
4.
Place the sensor on its back and drop the filter into the
lens chamber covering the sensor’s detector.
5.
Replace the cover making sure the filter remains in the
lens chamber and does not interfere with the attachment of the cover.
6.
Replace the sensor’s mounting plate and install the sensor in its water resistant enclosure.
STANDARD
HIGH
8362G06A.DS4
Figure 7. Sensitivity Pins Locations
2.
Locate the sensitivity pins under the battery on the right
side of the PIR when looking at the front of the PIR.
3.
To change to high sensitivity move the shorting jumper
to the pair of pins that are closer to the top of the PIR
(see Figure 7).
Note
If the shorting jumper is not used or placed incorrectly,
the sensor defaults to standard sensitivity.
4.
Walk test the PIR to verify the sensitivity.
Testing
Walk Testing
Walk testing should be done to determine the sensor’s
actual coverage area. The edge of the coverage pattern is
determined by the first flash of the LED. This may change
slightly depending upon the sensitivity setting. Walk test the
unit from both directions to determine the pattern boundaries.
1.
Remove the sensor body from the mounted mounting
plate, activate the tamper switch, and then remount the
body to activate the 60 second walk test mode.
2.
Walk across the coverage pattern to determine the coverage area, indicated by LED activation. Each activation extends the walk test mode for an additional 60
seconds.
Outdoor Motion Sensor
Mounting
After 60 seconds without motion the walk test mode and the
LED will no longer activate when motion is detected.
1.
Determine the desired mounting location for the sensor
leaving at least four inches of room above the wall
mount plate to attach the sensor.
2.
Attach the wall mount plate with the opening for the
swivel mount facing downward using the screws and
anchors supplied.
Excessive use of the walk test mode may reduce
battery life. Use only for initial setup and maintenance
testing.
3.
Attach the sensor assembly to the wall mount plate by
screwing the sensor assembly up into the opening in the
wall mount plate.
Note
4.
To remove the sensor for testing or battery replacement, slide the front cover of the sensor upward until
the sensor can be removed.
Filter Installation
A 1 inch by 1 inch piece of lens material has been included
with the outdoor motion sensor. This filter reduces the sensors sensitivity to white light sources (sunlight and head
lights) and infrared sources. Install this filter when experiencing unwanted sensor activations due to these sources.
4
CAUTION
When the walk test mode has ended, an alarm can be
transmitted only after 3 minutes have passed since
the previous alarm. This 3 minute lockout time
reduces unnecessary RF transmissions in high traffic
areas thereby extending battery life.
Environment Testing
Indoor Motion Sensors
Turn on all heating or air conditioning sources which would
normally be active during the protection period. Stand away
ITI® Indoor and Outdoor PIR Motion Sensors
Coverage Masking
from the sensor and outside the coverage pattern and watch
for alarms.
Replacing Batteries
Outdoor Motion Sensors
When battery replacement is necessary, observe proper
polarity (as shown in the battery compartment) when
installing the new battery. The sensor may be damaged if
installed incorrectly. Be sure to note that as you look at the
battery compartment, on the left side the positive battery
end is down and on the right side the positive end is up.
When the battery is replaced, wait at least 3 minutes after
installing the battery before activating the walk test mode.
See Figure 8 for battery locations.
Verify that the sensor’s coverage area doe not extend into
undesired areas that might cause unwanted activations.
These areas may include undesired human, pet, or automobile motion.
Coverage Masking
PIR
COVER
After walk testing and environment testing are completed,
masking labels can be applied to the sensor’s lens to block
detection of problem areas. The masking labels provided
are cut to match the corresponding lens segments.
1.
Determine which detection zone/lens segment needs a
masking label.
2.
Peel the desired mask label from its backing and apply
to the inside of the lens segment to be blocked.
PWB
COVER
LENS
TABS
Programming
SENSOR
BODY
TAMPER
SWITCH
Refer to the panel installation instructions for information
on programming the sensor into the panel.
MOUNTING
PLATE
Figure 8. PIR Components, Battery Locations, & Tamper
Switch
Final Testing
Final testing should be done to verify radio signal integrity
and confirm control panel programming and response. The
actual transmitter range can be determined by performing a
sensor test as follows:
8362G02A.DS4
Troubleshooting
Use the following guidelines if the system does not respond
correctly when the sensor is activated.
❑
Check programming and re-program sensor into panel
if necessary.
Move the sensor to another location and test for correct
response.
1.
After the sensor has been mounted, remove it from its
mounting plate and activate the tamper switch to start
the walk test mode.
2.
Replace the sensor in its mounting plate.
3.
Place the control panel in test mode. Move across the
detection pattern until the sensor’s LED turns on.
STOP your motion.
To relocate a sensor:
1.
Test the sensor a few inches from the original position.
4.
Listen for the appropriate system response. If the system does not respond, proceed to the “Troubleshooting” section.
2.
Increase the distance from the original position and
retest until an acceptable location is found.
3.
Mount the sensor in the new location.
4.
If no location is acceptable, test the sensor as described
below:
❑ Test a known good sensor at the same location.
❑ If the system does not respond, avoid mounting a
sensor at that location.
❑ If the replacement sensor functions, return the
problem sensor for repair or replacement.
Maintenance
At least once a year, the range and coverage should be verified for proper operation. The end user should be instructed
to put the sensor in walk test mode and walk through the far
end of the coverage pattern to verify proper detection.
ITI® Indoor and Outdoor PIR Motion Sensors
❑
5
Specifications
Specifications
Power source:
2 AA alkaline batteries
Typical battery life:
2-4 years at 68° F (not verified by
U.L.)
Temperature range: 32° to 120° F (Indoor Motion Sensor)
10° to 120° F (Outdoor Motion
Sensor)
Dimensions:
L = 2.875” X W = 2.375” X H =
1.875”
Notices
These devices comply with part 15 of the FCC rules. Operation is subject to the following two conditions:
❑
❑
These devices may not cause harmful interference.
These devices must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by Interactive Technologies, Inc. can void the users’ authority to
operate the equipment.
6 5 1 - 7 7 7 - 2 6 9 0
6 5 1 - 7 7 9 - 4 8 9 0
ITI is a registered trademark of Interactive Technologies, Inc.
6
ITI® Indoor and Outdoor PIR Motion Sensors

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project