Uniden DCT6465 Owner`s manual

Add to my manuals
72 Pages

advertisement

Uniden DCT6465 Owner`s manual | Manualzz
UP318BH(DCT6465) OM.book
2 ページ
2003年10月22日 水曜日 午後6時20分
UP318BH(DCT6465) OM.book
1 ページ
2003年10月22日 水曜日 午後6時20分
Step 1 Checking the Package Contents
Make sure your cordless phone‘s packaging includes the
following items (the number of items may vary depending on
model number within the series). If any of these items are
missing or damaged, contact the Uniden Parts Department.
TO INSTALL THE HANDSET BATTERY
(see page 12 for details)
Charge the handset battery pack
for at least 15-20 hours before
using your new cordless telephone
for the first time! Use only the
Uniden rechargeable battery pack
supplied with your new phone.
Remove the cover.
Connect the battery pack
connector with the correct
polarity and listen for a
click to insure connection.
Replace the cover.
Uniden Parts Department at (800) 554-3988
Hours: M-F 8:00 a.m. to 5:00 p.m. CST.
or visit our website at www.uniden.com for
replacement parts.
Use only the Uniden AC adapter
supplied with your new phone.
Plug the AC adapter cord
into the base unit
and then into a
120V AC outlet.
Place the handset in
the base and charge
continuously for
15 - 20 hours before
using the phone.
www.uniden.com
QUICK REFERENCE GUIDE [1]
QUICK REFERENCE GUIDE
• Base Unit
• Handset(s)
• AC Adapter(s)
• Wall Mount Adapter
• Rechargeable Battery Pack(s)
• Telephone Cord
• Belt Clip(s)
• Owner's Manual
• Other Printed Materials
Step 2 Install and Charge the Handset Battery
UP318BH(DCT6465) OM.book
2 ページ
2003年10月22日 水曜日 午後6時20分
Step 3 Connect to Phone Line
When the handset battery pack is fully charged (after 15-20
hours of charging), plug the telephone cord into the base unit
and then into a telephone wall jack.
Press ring/vol/∧ or ring/vol/∨ to select C I DC W and
then select/.
Press ring/vol/∧ or ring/vol/∨ to select CW On/CWDX
On , C W O n/ C WD X O ff , C W O ff / CW D X O ff and then
select/ (see page 24 for details).
TO SET LANGUAGE
Press menu/del in standby mode.
Your phone is set for tone dialing. If your local network
requires pulse dialing, refer to page 25.
Step 4 Setting Caller ID & Language Display Options
TO SET CALLER ID ON CALL WAITING AND CALL
WAITING DELUXE
For all Handset Menu Setup options, refer to page 17.
Press ring/vol/∧ or ring/vol/∨ to select H a nd se t
select/.
Se t up and then
Press ring/vol/∧ or ring/vol/∨ to select L a ng ua g e
and then select/.
Press ring/vol/∨ to choose a language
and then select/.
Step 5 Adjusting Ringer Level
In standby mode, press ring/vol/∧ or ring/vol/∨ on the
handset or ring/volume/∧ or ring/volume/∨ on the base to
select the desired volume.
Press menu/del in standby mode.
Press ring/vol/∧ or ring/vol/∨ to select G l ob a l
select/.
Se t up and then
[2] QUICK REFERENCE GUIDE
www.uniden.com
UP318BH(DCT6465) OM.book
3 ページ
2003年10月22日 水曜日 午後6時20分
1° Paso Inspección del contenido del embalaje
Asegúrese de que haya recibido los siguientes artículos en el
paquete (la cantidad de artículos puede variar dependiendo del
número del modelo dentro de la serie). Si alguno de estos
artículos falta o está dañado, comuníquese con el departamento
de partes de Uniden.
Para instalar la pila del receptor
(Consulte la página 12 para más detalles)
Cargue el paquete de batería to pila
por lo menos de 15 á 20 horas antes
de conectarlo a una línea telefónica.
Use solamente el paquete de pilas
recargable de Uniden suministrado
con su nuevo teléfono.
Quite la tapa.
Rojo
Conecte el enchufe del
paquete de las pilas con la
polaridad correcta y
escuche por un clic para
asegurar la conexión.
Negro
Negro
Rojo
Reponga la tapa.
Uniden Parts Department
Teléfono: (800)554-3988
Horas: de Lunes a Viernes desde las 8 a.m. hasta las
5:00 p.m., hora central O visítenos en nuestra página
Web en www.uniden.com para conseguir las partes
de reemplazo.
Use solamente el adaptador CA
de Uniden suministrado con su
nuevo teléfono.
Conecte el cable del
adaptador CA en la base
y luego en una toma CA
de 120 V.
Antes de usar el
teléfono, coloque el
receptor en la base y
cárguelo continuamente
por 15–20 horas.
www.uniden.com
Enrolle el cable.
Al enchue CA
Al CC IN 9V
Adaptador CA
(suministrado)
Guía de referencia rápida [3]
Guía de referencia rápida
• Base
• Receptor(es)
• Adaptador(es) CA
• Adaptador de montaje de pared
• Paquete(s) de pilas recargable(s)
• Cable telefónico
• Pinza(s) para la correa
• Manual para el usuario
• Otros impresos
2° Paso Instalación y carga de la pila para el receptor
UP318BH(DCT6465) OM.book
4 ページ
2003年10月22日 水曜日 午後6時20分
3° Paso Conexión a la línea telefónica
Cuando el paquete de pilas del receptor esté totalmente cargado,
después de una carga de 15-20 horas, conecte el cable telefónico
en la base y luego en el enchufe telefónico de la pared.
Oprima ring/vol/∧ o ring/vol/∨ para seleccionar la
Pr o gr g l ob a l , y luego select/.
Oprima ring/vol/∧ o ring/vol/∨ para seleccionar
CI D CW , y luego select/.
Oprima ring/vol/∧ o rring/vol/∨ para seleccionar C W
Ac t /C WD X A c t , C W A c t/ C WD X A pg , o CW Ap g /C WD X
Ap g , y luego select/ (consulte la página 24 para
más detalles).
Al enchufe Telefónico
A la línea Telefónica
Cable de línea Telefónica
Su teléfono está programado para marcar por tono. Si su red
local requiere la marcación por pulso, consulte la página 25.
4° Paso Programación de las opciones de identificación
de llamadas y del lenguaje en la pantalla
Para programar las opciones de identificación
de llamadas de llamadas en espera y llamada en
espera de lujo
Para todas las demás opciones de programación en el menú,
consulte la página 17.
Para programar el lenguaje
Oprima menu/del en el modo de espera.
Oprima ring/vol/∧ o ring/vol/∨ para seleccionar la
Pr o gr r e ce p to r , y luego select/.
Oprima ring/vol/∧ o ring/vol/∨ para seleccionar el
Le n gu aj e , y luego select/.
Oprima ring/vol/∨ para escoger el lenguaje,
y luego select/.
5° Paso Ajuste del nivel del timbre
Oprima menu/del en el modo de espera.
[4] Guía de referencia rápida
En el modo de espera, oprima ring/vol/∧ o ring/vol/∨ en el
receptor o ring/volume/∧ o ring/volume/∨ en la base para
seleccionar el volumen deseado.
www.uniden.com
UP318BH(DCT6465) OM.book
5 ページ
2003年10月22日 水曜日 午後6時20分
Contents
QUICK REFERENCE GUIDE
WELCOME/FEATURES/TERMINOLOGY
CONTROLS AND FUNCTIONS
DISPLAY AND ICONS
GETTING STARTED
Setting up the Phone
Mounting the Base Unit on a Wall
About the Menu Options
Setting Menu Options
BASICS
Making and Receiving Calls
Placing a Call on Hold
Redialing a Call
Adjusting the Handset Ringer, Earpiece and Speaker Volume
Adjusting the Base Ringer Volume and Speaker Volume
Do Not Disturb (DND)
Mute Microphone
Tone Dialing Switch-over
Traveling Out-of-Range
Clarity Booster
Privacy Mode
3-Way Conferencing
Find Handset
Flash and Call Waiting
Using One Touch Voice Mail Access
PHONEBOOK
Phonebook
Storing Phone Numbers, Names, Distinctive Rings,
and Speed Dial
Chain Dialing
Steps for Entering Names and Special Characters
Viewing the Phonebook
Making Calls Using the Phonebook
www.uniden.com
1
6
8
10
11
11
15
17
20
27
Speed Dialing
Editing or Erasing a Stored Name, Phone Number,
Distinctive Ring, and Speed Dial
Memory Dialing (base only)
CALLER ID
Caller ID and CIDCW (Caller ID on Call Waiting)
Viewing the Caller ID List
Deleting a Caller ID Message
Using the Caller ID Message List
Call Waiting Deluxe Features
27
28
28
29
30
31
31
32
32
33
33
34
35
35
36
EXPANDING YOUR PHONE
37
TROUBLESHOOTING
37
37
38
39
41
42
42
43
44
45
45
46
47
48
49
50
Expanding Your Phone
Connecting the Charger
Register the Handset to the Base
Using the DirectLink Mode
4-Way Conferencing
Intercom/Call Transfer Feature
Replacing the Base
50
50
51
52
53
53
55
ADDITIONAL INFORMATION
56
Changing the Digital Security Code
Installing the Beltclip
Headset Installation
Note on Power Sources
Maintenance
General Information
Liquid Damage
PRECAURIONS & WARRANTY
I.C. NOTICE
INDEX
MEMORY LIST
56
56
56
57
57
58
59
61
62
64
65
66
[5]
UP318BH(DCT6465) OM.book
Welcome
6 ページ
2003年10月22日 水曜日 午後6時20分
Congratulations on your purchase of the Uniden Expandable Cordless System telephone. This unit
is different from conventional cordless telephones. When the base unit is connected to AC power
and a telephone line, it can support up to 4 handsets. Using extra handsets, you can establish a
4-way conference call (2 handsets - Base Speaker Phone - an outside line). Additionally, with 4way conference using 2 handsets, another 2 handsets can establish an intercom call. You can
now place a fully featured cordless handset anywhere in your home or office where AC power is
available to connect the handset chargers.
Note: Some illustrations in this manual may differ from the actual unit for explanation purposes.
As an Energy Star Partner, Uniden has determined that this product or product
models meets the Energy Star guidelines for energy efficiency.
Energy Star is a U.S. registered mark.
Note: Energy Star  applies to DCT6465 only.
Features
2.4GHz Digital Expandable System
4 Handsets Expandability
Hands Free Speakerphone in the Handset and Base
Caller ID/Caller ID on Call Waiting
Call Waiting Deluxe
100 Programmable Memory Locations (Phonebook or Caller ID)
Trilingual Handset Display Menus (English, French, and Spanish)
Call Transfer and/or Intercom between Handsets, or Handset and Base
20 Distinctive Ring Options (10 ringer tones and 10 melody ringers)
Mute Feature
88 Channel Auto Scan
DirectLink Mode
Voice Mail Waiting Indicator and Access
Room/Baby Monitoring Capability
Battery Level Indicator
Clock Display
10 Memory Dial Location at Base
Dual Keypad at Base
[6] WELCOME/FEATURES/TERMINOLOGY
www.uniden.com
WELCOME/
FEATURES/
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
UP318BH CH05 Welcome.fm
7 ページ
2003年10月23日 木曜日 午後4時20分
This series features include AutoTalk and AutoStandby. AutoTalk allows you to answer a call by just removing
the handset from the cradle so you don't have to waste time pushing buttons. AutoStandby allows you to hang up by
simply returning the handset to the cradle.
To protect you against mis-billed calls, which might result from your phone being activated by other equipment, this
series has Random Code digital security, which automatically selects one of over approx. 130,000 digital security
codes for the handset and base.
Frequency Hopping Spread Spectrum (FHSS) technology improves calling range and clarity, and eliminates cross talk.
Because it rapidly changes transmission frequencies within the 2.4GHz bandwidth, this cordless phone helps reduce
the possibility of eavesdropping.
DirectLink mode is used when you have 2 or more handsets. You can use your handsets as transceivers.
IntegriSound Built in sound quality which provides lifelike conversations.
Be sure to visit our web site: www.uniden.com
Uniden is a registered trademark of Uniden America Corporation.
AutoTalk, AutoStandby, DirectLink, Random Code, and IntegriSound are trademarks of Uniden America.
Terminology
www.uniden.com
WELCOME/FEATURES/TERMINOLOGY [7]
WELCOME/
FEATURES/
•Standby Mode - The handset is not in use and talk/flash has not been pressed.
•Talk Mode The handset is not in the cradle and talk/flash or speaker has been pressed enabling a dial tone.
Ta l k appears on the display.
UP318BH(DCT6465) OM.book
8 ページ
2003年10月22日 水曜日 午後6時20分
Controls & Functions
1
6
2
7
3
4
8
14
15
11
12
13
18
19
20
21
22
5
[8] CONTROLS & FUNCTIONS
16
17
www.uniden.com
CONTROLS &
FUNCTIONS
9
10
1. Handset Antenna
2. Headset Jack Cover
3. Beltclip Hole
4. Hands-Free Speaker
5. Handset Battery Compartment
6. New Message LED
7. Handset Earpiece
8. LCD Display
9. Menu/del (delete) Key (P. 20 / P. 29, 43, 47)
10. (ring)/vol (volume) and ∧/∨ (P. 22 / P. 29)
a. ringer and volume control b. scroll keys for display screen
11. */tone/← Key (P. 23 / P. 32 / P. 40)
12. redial/pause Key (P. 28 / P. 27)
13. speaker Key (P. 27)
14. Select/ (voice mail) Key (P. 20 / P. 36)
15. Call id (Caller ID) key (P. 46)
16. End Key (P. 27)
17. Talk/flash Key (P. 27 / P. 35)
18. #/→ Key (P. 23 / P. 40)
19. (Phonebook) Key (P. 37)
20. Hold/transfer/int'com (Intercom) Key (P. 28 / P. 54 / P. 53)
21. Handset Microphone
22. Handset Charging Contacts
UP318BH(DCT6465) OM.book
9 ページ
23
2003年10月22日 水曜日 午後6時20分
24 25 26
32
33
34
35
28
29
30
31
36
37
23. Base Speaker
24. Charge LED
25. In use LED
26. Ringer off LED
27. Base Antenna
28. Memory Key (P. 44)
29. Redial Key (P. 29)
27
38
39
40
30. Pause Key (P. 27)
31. Base Charging Contacts
32. Mute/find handset Key (P. 31/35)
33. Intercom Key (P. 53)
34. Hold Key (P. 28)
35. (ring)/volume and ∧/∨ (P. 30)
36. (speaker) Key (P. 27)
41
37. Flash Key (P. 35)
38. Do not disturb Key (P. 31)
39. Microphone
40. DC IN 9V Jack
41. TEL LINE Jack
42.DC IN 9V Jack
43.Charging Contacts
44.Charge LED
44
www.uniden.com
CONTROLS & FUNCTIONS [9]
CONTROLS &
FUNCTIONS
For DCT6465 only
42
43
UP318BH(DCT6465) OM.book
10 ページ
2003年10月22日 水曜日 午後6時20分
Display and Icons
Example of the standby mode display
570#
*CPFUGV
0GYࠕࠗ࠙
ICON
Day of the week and time / battery icon
Handset ID and Banner
Number of new Caller ID calls received / Ringer off icon (when the ringer is Off)
STATUS
DESCRIPTION
Standby/Talk
Battery icons indicate the handset battery status. This icon cycles depending on
the battery status (empty, low, medium, and full).
ࠕࠗ࠙
Standby
ߦ
Talk
Mute icon appears when you mute the handset.
㨮
Talk
Speaker icon appears when the handset speaker phone is used.
$
Talk
Booster icon appears when the Clarity Booster feature is in use.
ߥ
Talk
Privacy icon appears when the Privacy Mode is turned on.
www.uniden.com
D I S P L AY A N D I C O N S
[10] DISPLAY AND ICONS
Ringer off icon indicates that ringer is turned off.
UP318BH(DCT6465) OM.book
11 ページ
2003年10月22日 水曜日 午後6時20分
note
Do the following steps:
A. Choose the best location.
B. Install the rechargeable battery pack into the handset.
C. Connect the base unit.
A. Choose the best location
Before choosing a location for your new phone, read “Installation Considerations” on page
63. Here are some important guidelines you should consider:
If your home has
specially wired alarm
equipment connected to
the telephone line, be
sure that installing the
system does not disable
your alarm equipment.
If you have questions
about what will disable
alarm equipment,
contact your
telephone company or
a qualified installer.
www.uniden.com
GETTING STARTED [11]
GETTING STARTED
Setting up the Phone
UP318BH(DCT6465) OM.book
12 ページ
2003年10月22日 水曜日 午後6時20分
B. Install the rechargeable battery pack into the handset
note
• Use only the
Uniden (BT-446)
rechargeable
battery pack
supplied with your
cordless telephone.
•Replacement battery
packs are also
available through the
Uniden Parts
Department at (800)
554-3988, Monday
thru Friday from 8:00
a.m. to 5:00 p.m. or
online at www.
uniden.com
Charge the handset battery pack for at least 15-20 hours before using your new cordless
telephone for the first time! The handset is powered by a rechargeable battery pack. The
battery recharges automatically when the handset is placed in the base unit. To maximize
the charge capacity of your battery pack, DO NOT plug the telephone cord into the base unit
and wall jack until the battery is fully charged.
1) Press down on the handset battery case cover (use the finger
indention for a better grip) and slide the cover downward
to remove.
2) Plug the battery pack connector (red & black wires) into the jack
inside the battery compartment (the connector notches fit into
the grooves of the jack only one-way). Match the wire colors to
the polarity label in the battery compartment, connect the
battery, and listen for a click to insure connection.
3) Make sure you have a good connection by slightly pulling on the
battery wires. If the connection is secure, the battery jack will
remain in place.
4) Place the battery case cover back on the handset by sliding it
upwards until it clicks into place.
5) Place the handset in the base unit for 15-20 hours without
interruption. The base unit's LED light (labeled charge)
illuminates once the handset is placed in the base. The LED light
will illuminate whether the battery pack is connected or not.
If the base charge LED light does not illuminate:
• Check to see if the AC adapter is plugged into the base unit and the electrical wall outlet
properly (use only the supplied AC adapter. Do not use any other AC adapter.)
• Check to see if the handset is sitting correctly in the base and making good contact with
the base unit's charging contacts.
[12] GETTING STARTED
www.uniden.com
UP318BH(DCT6465) OM.book
13 ページ
2003年10月22日 水曜日 午後6時20分
When the battery pack is very low and need to be charged, the phone is programmed to
eliminate functions in order to save power.
The battery pack needs to be charged when:
- The empty battery icon appears.
- Lo w B at t er y appears in the display.
If the phone is in standby mode, none of keys will operate.
If you are on a call, complete your conversation as quickly
as possible, and return the handset to the cradle.
Cleaning the battery charging contacts
To maintain a good charge, it is important to clean
the charging contacts on both the handset and the
base unit once a month. Using water only, dampen
a cloth to clean the charging contacts. Then make
sure to go back over the charging contacts with a
dry cloth before returning the handset to the base
to charge.
Caution: Do not use paint thinner, benzene, alcohol,
or other chemical products. Doing so may discolor the
surface of the telephone and damage the finish.
www.uniden.com
.QY$CVVGT[
note
•Even when the battery
pack is not being used,
it will gradually
discharge over a long
period of time.
For optimum
performance, be sure
to return the handset
to the base unit after a
telephone call.
•Standby Mode The handset is not in
use and talk/flash
has not been pressed.
•Talk Mode The handset is not in
the cradle and talk/
flash or speaker has
been pressed enabling
a dial tone. Ta l k
appears on the display.
GETTING STARTED [13]
GETTING STARTED
Low battery alert
UP318BH(DCT6465) OM.book
14 ページ
2003年10月22日 水曜日 午後6時20分
C. Connect the base unit
note
•Use only the supplied
AD-830 AC adapter.
Do not use any other
AC adapter.
•Place the power cord
so that it does not
create a trip hazard or
where it could
become chafed and
create a fire or
electrical hazard.
1) Connect the AC adapter to the DC IN 9V jack and to
a standard 120V AC wall outlet.
2) Set the base on a desk or tabletop, and place the
handset in the base unit.
3) Raise the antenna to a vertical position.
4) Make sure that the charge LED illuminates.
If the LED does not illuminate, check to see that the
AC adapter is plugged in and the handset makes
good contact with the base charging contacts.
• Connect the AC adapter to a continuous power supply.
• Place the base unit close to the AC outlet so that you can
unplug the AC adapter easily.
• After installing the battery pack in the handset, charge your
handset at least 15-20 hours before plugging into the
phone line.
5) Once the handset battery pack is fully charged,
connect the telephone line cord to the TEL LINE jack
and to a telephone outlet.
If your telephone outlet isn't modular, contact
your telephone company for assistance.
[14] GETTING STARTED
www.uniden.com
UP318BH(DCT6465) OM.book
15 ページ
2003年10月22日 水曜日 午後6時20分
Standard wall plate mounting
This phone can be mounted on any standard wall plate.
1) Snap the wall mount adapter into the notches on the
base top.
DO NOT use an AC
outlet controlled by a
wall switch.
2) Plug the AC adapter into the DC IN 9V jack.
3) Wrap the AC adapter cord inside the molded wiring
channel as shown.
4) Plug the AC adapter into a standard 120V AC wall outlet.
5) Plug the telephone line cord into the TEL LINE jack.
Wrap the cord inside the molded wiring channel as shown.
6) Plug the telephone line cord into the
telephone outlet.
7) Raise the antenna to a vertical position.
8) Align the mounting slots on the base with the
mounting posts on the wall. Then push in and
down until the phone is firmly seated.
www.uniden.com
GETTING STARTED [15]
GETTING STARTED
Mounting the Base Unit on a Wall
UP318BH(DCT6465) OM.book
16 ページ
2003年10月22日 水曜日 午後6時20分
If you don't have a standard wall plate, you can mount your phone directly to the wall.
Before doing this, consider the following:
• Avoid electrical cables, pipes, or other items behind the mounting location that could
cause a hazard when inserting screws into the wall.
• Try to mount your phone within 5 feet of a working phone jack to avoid excessive lengths.
• Make sure the wall material is capable of supporting the weight of the base and handset.
• Use #10 screws (minimum length of 1-3/8 inches) with anchoring devices suitable for the
wall material where the base unit will be placed.
1) Insert two mounting screws into the wall (with their
appropriate anchoring device), 3-15/16 inches apart.
Allow about 1/8 of an inch between the wall and screw
heads for mounting the phone.
2) Refer to steps 1 through 8 on page 15 to mount
the telephone.
[16] GETTING STARTED
www.uniden.com
GETTING STARTED
Direct wall mounting
UP318BH(DCT6465) OM.book
17 ページ
2003年10月22日 水曜日 午後6時20分
There are 5 main menu options, (DirectLink Mode, Room/Baby Monitor, Handset Setup,
Global Setup and System Reset) and 16 submenu options.
Summary of Main Menu and Submenu Options
DirectLink Mode
DirectLink Mode allows a pair of handsets to work without the base unit, for direct handsetto-handset communication. Use them at sporting events or while shopping to stay in
contact with family members or friends. You must set the two handsets to DirectLink Mode
to utilize this feature.
Room/Baby Monitor
This feature allows you to monitor sounds in another room (see page 21 for setup). One
handset (or the base) is placed in the desired room to monitor (acts as remote mic), and the
other is placed near listener (remote speaker). This is useful for monitoring child activities.
www.uniden.com
note
•During Global Setup
and System Reset,
make sure your
cordless phone is in
standby mode (not in
use), and all handsets
are within range of the
main base unit.
•If an incoming call is
received during room
monitor mode, the
user’s handset will
receive incoming tones
or beeps. To cancel
room/baby monitor
and receive the call,
press talk/flash or
speaker. If monitoring
from base unit, press
speaker. The handset
or the base that’s
placed in the room
being monitored, will
NOT sound or receive
incoming tones.
GETTING STARTED [17]
GETTING STARTED
About the Menu Options
UP318BH(DCT6465) OM.book
18 ページ
2003年10月22日 水曜日 午後6時20分
The following submenu options must be set separately for each handset.
Submenu option
Description
Edit Voice Mail
Program or delete the voice mail access number (see page 21).
Ringer Tones
(Default is Flicker)
Adjusting the ringer tone (tone your phone makes when ringing)
(see page 22).
Distinct. Ring
(Default is on)
Set the distinctive ring (see page 22). "Distinctive Ringer" allows you to
preset memory locations with a designated ring tone. When an incoming call
is received and the Caller ID information matches the information in one of
the memory locations, the distinctive ring that has been stored for that
particular Caller will sound. If you have set multiple memory locations with
distinctive rings, switching the setting to "Distinctive Off" will result in no
distinctive ringing. All incoming calls will have a normal ring tone.
Switching to "Distinctive On" will activate all programmed distinctive ring
memory locations.
AutoTalk
(Default is off)
Allows you to answer the phone without pressing talk/flash or speaker.
When the AutoTalk is set to on, simply remove the handset from the cradle
and the phone automatically answers the call (see page 22).
Anykey Answer
(Default is off)
Allows you to answer the phone without pressing talk/flash or speaker.
When the Anykey Answer is on, you can answer a call by pressing any number
key, /tone/←, or #/→ on the handset (see page 23).
Banner (True Banner)
Customize your handset(s) by giving it a banner name. The name will be
displayed on the LCD screen during standby mode, Intercom, Transfer, Room
Monitor and Copy Phonebook operation. The banner name will be displayed on
the receiving handset as well (see page 23).
Language
(Default is English)
The menu display options can be set to English, French or Spanish for easy
setup use (see page 23).
Key Touch Tone
(Default is on)
Allows you to set your phone's key touch-tone to on or off (tone your keypad
makes when keys are pressed) (see page 23).
[18] GETTING STARTED
*
www.uniden.com
GETTING STARTED
Handset Setup
UP318BH(DCT6465) OM.book
19 ページ
2003年10月22日 水曜日 午後6時20分
If you change one of the Global settings, you change the setting for all additional handsets.
Only one handset can change Global settings at a time.
Submenu option
Description
Day & time
Set the day and time of your display (see page 24).
CIDCW (Default is
CW on/CWDX off)
Set the Caller ID on Call Waiting (CIDCW) setting. CIDCW performs the same as
regular Caller ID on a call waiting number (see page 24). Call Waiting Deluxe
allows you to handle call waiting calls in seven different ways (see page 49).
Area Code
Store or edit the area code. If you enter a 3-digit area code number in the"Area
Code" option, your local area code does not appear in the Caller ID message. For
calls received from outside your local area code, you will see a full 10-digit number
(see page 24).
Note: If your calling area requires 10-digit dialing, do not program this option.
Dial Mode
(Default is tone)
Set the dial mode to tone or pulse (see page 25). Most phone systems use tone
dialing, which send DTMF tone through phone line. The default is tone dialing.
Depends on your dialing system, set the dial mode.
Copy Phonebook
Allow you to transfer the phonebook data stored in one handset to another
handset (see page 25).
Voice Mail Tone
(Default is on)
If your service does not support SDT message signal, set your VMWI (Visual Message
Waiting Inculcator) not to detect SDT message signal (see page 26).
System Reset
System Reset is used to clear the handset's ID from the main base unit, or the base ID from the handset.
Submenu option
Description
Deregister HS
Clear the handset ID from the base. Use this option, for example, when you
change the digital security code (see page 26).
Replacing Base
Clear the base ID. Use this option, for example, if you wish to deregister the base
to use the handset with another base of the DCT series (DCT646/DCT6465/DCT648/
DCT6485 series) (see page 26).
www.uniden.com
GETTING STARTED [19]
GETTING STARTED
Global Setup
UP318BH(DCT6465) OM.book
20 ページ
2003年10月22日 水曜日 午後6時20分
Entering the Menu
1) Press the menu/del key in standby mode.
&KTGEV.KPM/QFG
2) Use ring/vol/∧ or ring/vol/∨ to move the pointer to a
4QQO/QPKVQT
desired main menu (DirectLink Mode, Room Monitor,
*CPFUGV5GVWR
Handset Setup, Global Setup, and System Reset).
3) Press select/ to select the desired main menu.
4) Use ring/vol/∧ or ring/vol/∨ to select a desired submenu, and then press select/
to enter.
In the submenu, use ring/vol/∧ or ring/vol/∨ to select an item.
Press select/ to confirm your selection. For detailed instructions, see the following
sections for the desired submenu.
5) To exit the menu, press end or place the handset to the cradle.
DirectLink Mode
Using the DirectLink Mode
1) Enter the DirectLink Mode menu (see "Entering the
6QGPVGT
Menu" on page 20). T o e nt e r D ir e ct Li n k m od e p re s s
&KTGEV.KPMOQFG
[ S EL EC T ] appears.
RTGUU=5'.'%6?
2) Press select/ to enter the DirectLink mode. You will
hear a confirmation tone, and D ir e ct Li n k M od e
C o mp le t e appears.
3) To return back to the normal mode, exit the DirectLink mode. To exit the DirectLink
mode, press menu/del, and then select/, or return the handset to the cradle.
[20] GETTING STARTED
www.uniden.com
GETTING STARTED
Setting Menu Options
UP318BH(DCT6465) OM.book
21 ページ
2003年10月22日 水曜日 午後6時20分
Using Room Monitor
1) Enter the Room Monitor menu (see "Entering the Menu"
on page 20). T o R oo m M o ni to r appears.
2) Select the handset or base you want to monitor by using
ring/vol/∧ or ring/vol/∨.
3) Press select/.
R o om M on i to r appears, and you hear sounds in the room
where the handset or base is installed.
4) To finish the Room Monitor, press end or return the
handset to the cradle.
note
6Q4QQO/QPKVQT
*CPFUGV
$CUG
Room monitoring can be
between handsets or
base unit and handset.
4QQO/QPKVQT
*CPFUGV
Handset Setup
Programming your Voice Mail Access Number
1) Enter the Handset Setup menu, and then the Edit Voice
Mail submenu (see "Entering the Menu" on page 20).
E d it V_ m ai l N o. appears.
'FKV8AOCKN0Q
㨫
2) Enter your personal access number using the number keypad (0-9),
menu/del, or redial/pause (up to 20 digits).
3) Press select/. You will hear a confirmation tone.
*/tone/←, #/→,
To delete the current Voice Mail Access Number, delete all numbers in step 2 using
menu/del and select/.
www.uniden.com
GETTING STARTED [21]
GETTING STARTED
Room/Baby Monitor
UP318BH(DCT6465) OM.book
22 ページ
2003年10月22日 水曜日 午後6時20分
1) Enter the Handset Setup menu, and then the Ringer
Tones submenu (see "Entering the Menu" on page 20).
&KTGEV.KPM/QFG
4QQO/QPKVQT
*CPFUGV5GVWR
There are 10 ringer tones or 10 melodies to choose from.
- Ringers [Flicker, Clatter, Soft Alert, Wake Up, Light Bug,
Beep Boop, Tone Board, Chip Chop, Party Clap, Reminder]
- Melodies [Beethoven's Symphony #9 (Beethoven9), For
4KPIGT6QPGU
Elise (Elise), We Wish You A Merry Christmas (Merry(NKEMGT
Xmas), Home Sweet Home (Hm Swt Hm), Lorri Song #6
%NCVVGT
(Lorri Song), When the Irish Eyes Are Smiling (Irish
Eyes), Aura Lee, Let Me Call You Sweet Heart
(Sweetheart), Star Spangled Banner (Star Spngl), Old MacDonald (Old MacDld)]
2) Press ring/vol/∧ or ring/vol/∨ to move the pointer. You will hear the ringer or melody as
you scroll through the options.
3) Press select/. You will hear a confirmation tone.
Distinctive Ringer Setup
1) Enter the Handset Setup menu, and then the Distinctive
Ring submenu (see "Entering the Menu" on page 20).
2) Press ring/vol/∧ or ring/vol/∨ to select O n or O f f .
3) Press select/. You will hear a confirmation tone.
&KUVKPEVKXG4KPI
1P
1HH
Setting the AutoTalk
1) Enter the Handset Setup menu, and then the Auto Talk
submenu (see "Entering the Menu" on page 20).
2) Press ring/vol/∧ or ring/vol/∨ to select O n or O f f .
3) Press select/. You will hear a confirmation tone.
[22] GETTING STARTED
#WVQ6CNM
1P
1HH
www.uniden.com
GETTING STARTED
Selecting a Ringer Tone
UP318BH(DCT6465) OM.book
23 ページ
2003年10月22日 水曜日 午後6時20分
1) Enter the Handset Setup menu, and then the Anykey
Answer submenu (see "Entering the Menu" on page 20).
2) Press ring/vol/∧ or ring/vol/∨ to select O n or Of f .
3) Press select/. You will hear a confirmation tone.
#P[MG[#PUYGT
1P
1HH
Setting the True Banner
1) Enter the Handset Setup menu, and then the Banner
submenu (see "Entering the Menu" on page 20).
2) Use the number keypad (0-9), */tone/←, #/→, or
menu/del to enter or edit the name.
3) Press select/. You will hear a confirmation tone.
$CPPGT
/
AQ
AO
A
AU
A2
AJ
AQ
AP
AG
A
Selecting a Language
1) Enter the Handset Setup menu, and then the Language
submenu (see "Entering the Menu" on page 20).
2) Press ring/vol/∧ or ring/vol/∨ to choose E ng l is h ,
(French), or
(Spanish).
3) Press select/. You will hear a confirmation tone.
.CPIWCIG
'PINKUJ
(TCP㩟CKU
Setting the Key Touch Tone
1) Enter the Handset Setup menu, and then the Key Touch
Tone submenu (see "Entering the Menu" on page 20).
2) Press ring/vol/∧ or ring/vol/∨ to select O n or Of f .
3) Press select/. You will hear a confirmation tone.
www.uniden.com
-G[6QWEJ6QPG
1P
1HH
GETTING STARTED [23]
GETTING STARTED
Setting the Anykey Answer
UP318BH(DCT6465) OM.book
24 ページ
2003年10月22日 水曜日 午後6時20分
note
•When a Global setting
is changed from
one handset, this
affects all registered
handsets.
•For setting the day
and time, the idle
time-out is extended
to 2 minutes.
Setting Day and Time
1) Enter the Global Setup menu, and then the Day & Time
&C[6KOG
submenu (see "Entering the Menu" on page 20).
570#/
2) Press ring/vol/∧ or ring/vol/∨ to select the day of the
week, and then press select/.
=㨬㨲㨱㨭5'.'%6?
3) Press ring/vol/∧ or ring/vol/∨ to set hour and then
press select/.
4) Press ring/vol/∧ or ring/vol/∨ to set minute and then press select/.
5) Press ring/vol/∧ or ring/vol/∨ to choose A M or P M , and then press select/.
You will hear a confirmation tone.
Setting CIDCW (Caller ID on Call Waiting)
1) Enter the Global Setup menu, and then the CIDCW
submenu (see "Entering the Menu" on page 20).
2) Press ring/vol/∧ or ring/vol/∨ to select C W On /C W DX O n ,
C W O n /C WD X O ff , or C W O ff /CW DX Of f , and then press
select/. You will hear a confirmation tone.
%+&%9
%91P%9&:1P
%91P%9&:1HH
Setting the Area Code
•When the area code
has already been
stored in memory, the
stored area code will
be displayed.
To change it, use
menu/del and number
keys to enter the new
area code.
1) Enter the Global Setup menu, and then the Area Code
submenu (see "Entering the Menu" on page 20).
2) Press the number keypad (0-9) to enter a 3-digit
area code.
3) Press select/. You will hear a confirmation tone.
[24] GETTING STARTED
#TGC%QFG
㨫AA
www.uniden.com
GETTING STARTED
Global Setup (All Registered Handsets)
UP318BH(DCT6465) OM.book
25 ページ
2003年10月22日 水曜日 午後6時20分
GETTING STARTED
Setting the Dial Mode
1) Enter the Global Setup menu, and then the Dial Mode
submenu (see "Entering the Menu" on page 20).
2) Press ring/vol/∧ or ring/vol/∨ to change the select,
T o ne or Pu l se (the initial setting is Tone).
3) Press select/. You will hear a confirmation tone.
&KCN/QFG
6QPG
2WNUG
• If you are not of your dialing system, set the unit to tone dialing. Make a trial call.
If the call connects, leave the setting as is, otherwise set the unit to pulse dialing.
• If your phone system requires pulse dialing and you need to send DTMF tones in
certain situations during a call, you may Switch Over to tone dialing (refer to “Tone
Dialing Switch-over” on page 32)
Copy Phonebook
1) Enter the Global Setup menu, and then the Copy
%QR[2JQPGDQQM
Phonebook submenu (see "Entering the Menu" on
1PG/GOQT[
page 20).
#NN/GOQT[ZZZ
2) Press ring/vol/∧ or ring/vol/∨ to choose On e M em o ry or
A l l M em o ry , and then press select/.
If you choose A l l M em or y , go to step 4.
3) Press ring/vol/∧ or ring/vol/∨, or the number keypad (0-9) to select the phonebook
location you want to export, and then press select/.
4) Press ring/vol/∧ or ring/vol/∨ to select the handset to which you want transfer the
phonebook locations, and then press select/.
If you choose A l l M em or y in the step 2, A re yo u s ur e ? appears.
Press ring/vol/∧ or ring/vol/∨ to select Y e s , and then press select/.
•If you receive a call or
set up the Global Setup
menu, the transfer will
be canceled.
•If an error occurs, the
phonebook locations
transferred before the
error were stored in the
receiving handset.
Unavailable appears on
the display.
•When the memory of the
receiving handset is full,
The phonebook locations will be transferred to the handset. On the receiving handset,
R e ce i vi n g and the handset name appear. When the transfer complete, D o ne ! appears on
the handset.
www.uniden.com
note
Not enough memory
in Receiving
Handset appears. You
cannot transfer the
phonebook location.
GETTING STARTED [25]
UP318BH(DCT6465) OM.book
26 ページ
2003年10月22日 水曜日 午後6時20分
1) Enter the Global Setup menu, and then the Voice Mail
Tone submenu (see "Entering the Menu" on page 20).
2) Press ring/vol/∧ or ring/vol/∨ to set the voice message
indication (SDT message signal) to O n or O ff .
3) Press select/. You will hear a confirmation tone.
note
Make sure to perform
the Replacing Base
after de-register
the handset.
8QKEG/CKN6QPG
1P
1HH
System Reset
De-register the Handset
1) Enter the System Reset menu, and then the Deregister HS
submenu (see "Entering the Menu" on page 20).
2) Press ring/vol/∧ or ring/vol/∨ to select the handset ID
to be de-registered from the list, and then press
select/. D e re g is t er H S ? appears.
3) Press ring/vol/∧ or ring/vol/∨ to select Y e s , and then
press select/. You will hear a confirmation tone.
When de-registration is complete, De r eg i st r at io n
C o mp le t e appears.
4) After de-registering the handset, move to "Replacing the
Base Setting" below.
9JKEJ*CPFUGV!
*CPFUGV
*CPFUGV
&GTGIKUVGT*5!
;GU
0Q
Replacing the Base Setting
1) Enter the System Reset menu, and then the Replacing
4GRNCEGDCUG!
Base submenu (see "Entering the Menu" on page 20).
;GU
R e pl ac e b a se ? appears.
0Q
2) Press ring/vol/∧ or ring/vol/∨ to select Y e s , and then
Press select/. You will hear a confirmation tone.
The base information will be deleted.
When replacing the base is complete, P l ac e h an d se t o n m ai n b a se to r e gi s te r
appears, register the handset to the new base (see page 51).
[26] GETTING STARTED
www.uniden.com
GETTING STARTED
Voice Mail Tone
UP318BH(DCT6465) OM.book
27 ページ
2003年10月22日 水曜日 午後6時20分
Making and Receiving Calls
note
This handset has a built-in speakerphone that allows you to have a hands-free
conversation. This feature allows you to communicate easily while performing
other tasks, such as cooking. 㨮 appears during hands-free conversations.
•To set Autotalk, see
page 22 or to set
Anykey Answer see
page 23.
You can easily switch a call from normal conversation to hands-free
conversation. To switch a call, press speaker during the call.
From the Handset
From the Base
Normal conversation
Hands-free conversation
Press
(speaker).
*
•If the line is in use by
another handset(s),
To make a call
Handset Off the Cradle
1) Press talk/flash.
2) Listen for the dial tone.
3) Dial the number.
OR
Dial the number, and then press
talk/flash.
To hang up
Press end or return the handset to the cradle (AutoStandby). Press
To enter a
pause within
the dialing
sequence
When you dial the number in standby mode, press redial/
pause. P appears in the display, which represents a pause.
www.uniden.com
Handset Off the Cradle
1) Press speaker.
2) Listen for the dial tone. 1) Press
(speaker).
3) Dial the number.
2) Listen for the dial tone.
OR
3) Dial the number.
Dial the number and then
press speaker.
L in e I n U se
appears in the display
of all registered
handset's display, that
are not in use.
(speaker).
Press
(speaker).
When you dial the number
press pause.
BASICS [27]
BASICS
Handset On the Cradle
Pick up the handset (AutoTalk) or
pick up the handset and press
talk/flash.
To answer a call
Handset Off the Cradle
Handset Off the Cradle
Press any number key, /tone/ Press speaker.
←, or #/→ (Any Key Answer), or
press talk/flash.
•The handset
microphone is located
at the bottom of the
handset (see "Controls
and Functions" on
page 8). Position
yourself as near to the
handset as possible
and speak clearly.
UP318BH(DCT6465) OM.book
28 ページ
2003年10月22日 水曜日 午後6時20分
Placing a Call on Hold
note
•You can keep a call
on hold 5 minutes.
When 5 minutes has
passed, the call is
disconnected and the
phone returns to
standby mode.
*QNFVQVTCPUHGT
*CPFUGV
$
*CU
PG
FUGV
For the handset, after 10 seconds, the handset display screen will read, L in e O n H ol d .
2) To talk to the caller, press talk/flash or speaker on a
handset (or
(speaker) on the base). The phone will
return to the call.
570#
*CPFUGV
.KPG1P*QNF
Redialing a Call
The last three phone numbers dialed can be quickly redialed.
4GFKCN
Redialing from Standby Mode
1) Press redial/pause in standby mode.
2) Press redial/pause again. Each press of redial/pause will
display one of the last three number redialed.
3) Press talk/flash or speaker. The selected number is dialed.
4) To hang up, press end.
Redialing from Talk Mode
1) Press talk/flash or speaker.
2) Press redial/pause. The last number dialed will be
displayed and redialed. To hang up, press end.
[28] BASICS
redial/pause
4GFKCN
redial/pause
4GFKCN
redial/pause
www.uniden.com
BASICS
•While a call is on
hold, CIDCW can not
be received.
1) During a call, press hold/transfer/int’com on the
handset (or hold on the base).
UP318BH(DCT6465) OM.book
29 ページ
2003年10月22日 水曜日 午後6時20分
Deleting a Redial Record
1) Press redial/pause in standby mode.
2) Press redial/pause repeatedly to display the number to
be deleted.
3) Press menu/del.
3) Press ring/vol/∧ or ring/vol/∨ to choose Y es .
4) Press select/. The redialed number is deleted.
&GNGVG4GFKCN!
;GU
0Q
Storing a Redial Record
1)
2)
3)
4)
•If the number exceeds
32 digits, only the first
32 digits are retained
in redial memory.
•If the redial memory
is empty, you will hear
a beep.
BASICS
Press redial/pause in standby mode.
Press redial/pause repeatedly to display the number to be stored.
Press select/. S to re / Ed i t N am e appears.
To complete the setting, follow the steps 3-8 in "Storing Phone Numbers, Names,
Distinctive Rings, and Speed Dial" on page 37-38.
note
Redialing from the Base
1) Press
(speaker) on the base.
2) Press redial on the base. The last number dialed from the base is redialed.
Adjusting the Handset Ringer, Earpiece and
Speaker Volume
Handset ringer volume
/
Press the volume up key or volume down key (labeled as
vol/∧ or
/vol/∨) in standby mode to select one of three
ringer volume (off, low, or high).
www.uniden.com
BASICS [29]
UP318BH(DCT6465) OM.book
30 ページ
2003年10月22日 水曜日 午後6時20分
Earpiece and speaker volume
/vol/∧ or
/vol/∨ key)
Pressing the volume up key or volume down key (labeled as
during a call will change the earpiece volume of the handset. This setting will remain in
effect after the telephone call has ended.
When you press volume up key (ring/vol/∧) in the maximum volume level or volume down key
(ring/vol/∨) in the lowest volume level, an error tone sounds.
Ringer Mute
note
Adjusting the Base Ringer Volume and Speaker Volume
Base ringer volume
•If you select Off, the
ringer off LED on the
base will be illuminate.
•Standby Mode - The
handset is not in use
and talk/flash has
not been pressed.
In standby mode, press ring/volume/∧ or ring/volume/∨ on the base to select one of four
base ringer volume settings (High, Medium, Low, and Off). Each time ring/volume/∧ or
ring/volume/∨ is pressed, the volume setting is changed. You will hear the current ringer
volume revel. You have four ringer volume options. One allows you to turn the base ringer
off. The other three are volume levels. You can also adjust the volume when the phone is
ringing by pressing ring/volume/∧ or ring/volume/∨.
Speaker volume
When the base speaker is in use, press ring/volume/∧ or ring/volume/∨ on the base to adjust
the volume. Press ring/volume/∧ for louder or ring/volume/∨ for softer. Press and hold ring/
volume/∧ or ring/volume/∨ on the base to scroll quickly through the volume levels.
[30] BASICS
www.uniden.com
BASICS
You can temporarily mute the incoming ring. When the handset is off the cradle and the
phone is ringing, press end. The incoming ring will return to the previous setting starting
with the next incoming call.
UP318BH(DCT6465) OM.book
31 ページ
2003年10月22日 水曜日 午後6時20分
Do Not Disturb (DND)
DND allows you to mute the ringer of the handset and the base at once. Additionally, if you
have more than one handset, ringer for all handsets will be muted. To do this, in the
standby mode, press and hold do not disturb on the base. You will hear a confirmation tone
and the DND LED illuminates. To cancel, press do not disturb again. You can also mute the
ringer tone while the phone is ringing by pressing do not disturb on the base.
Mute Microphone
With the handset
BASICS
You can temporarily turn off the microphone so that the person you are talking with cannot
hear you.
1)Press menu/del during talk mode (while phone is in use).
2)Press ring/vol/∧ or ring/vol/∨ to move the pointer to M u te and then select/.
M ute O n and ߦ appear in the display. To cancel muting, repeat above step again when Mute
is set to on, Mu t e Of f appears.
With the base
While using the base speakerphone, press mute/find handset on the base to turn Off the
microphone. Press mute/find handset again or press
(speaker) to cancel muting.
www.uniden.com
BASICS [31]
UP318BH(DCT6465) OM.book
32 ページ
2003年10月22日 水曜日 午後6時20分
Tone Dialing Switch-over
note
•The tone feature only
applies when the dial
mode is set to pulse.
•This special number
can be stored in a
memory location. This
is referred to as Chain
Dialing (see page 38).
Some telephone companies use equipment that requires pulse
dialing (sometimes referred to as rotary dialing). If you need
to enter tone dialing digits, you can switch-over to tone
dialing during the call. This feature is useful when you need
tone dialing to use automated systems, for example, entering
your bank account number after you have called your bank.
BASICS
Initially make your call with pulse dialing mode. Once your call
connects, press */tone/← on the handset (or */tone on the
base). Enter the desired number. These digits will be sent as
tone dialing. Once the call ends, tone mode is canceled and
pulse dialing mode resumes.
Traveling Out-of-Range
During a call, as you begin to move your handset too far from your base unit, noise may
increase. If you pass the range limits of the base unit, you will hear a beep and see Ou t o f
R a ng e on the display, and then the handset returns to standby mode. You may return to the
call if you move your handset within the range limits of the base and press talk/flash or
speaker within 30 seconds.
[32] BASICS
www.uniden.com
UP318BH CH12 Basics.fm
33 ページ
2003年10月23日 木曜日 午後4時21分
Clarity Booster
If you encounter interference while using your phone, you
can manually improve the sound by setting the Clarity
Booster to on. This works only when the phone is in use.
6CNM$
$QQUV1P
1) Press menu/del during talk time (while phone is in use).
2) Press ring/vol/∧ or ring/vol/∨ to move the pointer to C la r it y B oo s t ,
and then select/.
B o os t O n and B appear in the display.
To turn Off the Clarity Booster, repeat above step again when the Clarity Booster is on,
B o os t O f f appears.
BASICS
Privacy Mode
Privacy Mode allows you privacy, and guarantee of no interruption from the base and other
registered handsets. This works only when the phone is in use.
1) Press menu/del during talk time (while phone is in use).
2) Press ring/vol/∧ or ring/vol/∨ to move the pointer to
6CNM
P r iv a cy Mo de , and then select/.
2TKXCE[/QFG1P
P r iv a cy Mo de On and ߥ appear in the display.
To exit the Privacy Mode, repeat above step again when
the Privacy Mode is on.
P r iv a cy Mo de Of f appears.
www.uniden.com
BASICS [33]
UP318BH(DCT6465) OM.book
34 ページ
2003年10月22日 水曜日 午後6時20分
3-Way Conferencing
The phone permits 3-way conversations between the handset, base, and an outside line.
When speaking on the handset
1) Press (speaker) on the base to initiate the
3-way conversation.
2) To hang up, press
(speaker) on the base.
The handset will still be connected to the call.
BASICS
When speaking on the base
1) Press talk/flash or speaker on the handset to initiate the
3-way conversation.
2) To hang up, return the handset to the cradle, or press end
key on the handset. The base will still be connected to
the call.
[34] BASICS
www.uniden.com
UP318BH(DCT6465) OM.book
35 ページ
2003年10月22日 水曜日 午後6時20分
Find Handset
To locate the handset, press mute/find handset on the
base when the base is in standby mode. All registered
handsets beeps for 60 seconds, and Pag ing appears on the
handset display. To cancel paging, press any key on the
handset or mute/find handset on the base.
note
•If the battery pack is
completely drained,
the handset will not
beep when paging.
If you have Call Waiting service and a call waiting tone sounds
while you are on a call, press talk/flash on the handset (or
flash on the base) to accept the waiting call. There is a short
pause, and then you will hear the new caller. To return to the
original caller, press talk/flash on the handset (or flash on
the base) again.
www.uniden.com
•You must subscribe
through your local
telephone company to
receive Call Waiting or
Caller ID on Call
Waiting service.
BASICS [35]
BASICS
Flash and Call Waiting
UP318BH(DCT6465) OM.book
36 ページ
2003年10月22日 水曜日 午後6時20分
Using One Touch Voice Mail Access
note
You must subscribe to
voice mail service from
your telephone company
in order to use this
feature. The voice mail
service company will
provide you with the
access number.
If you subscribe to voice mail service, you can use your phone to access your voice mailbox.
The new message LED flashes whenever you have messages waiting in your voice mailbox.
Just program the handset with your access number, and you can get your messages at
the touch of a button on the handset. (The voice mail service provider will supply you
with the access number. This number may be simply a phone number. Refer to the
provider's literature).
•To program or delete your Voice Mail Access Number, See page 21.
Dialing your Voice Mail Service
Voice Mail Access
The new message LED on the handset is designed to work with your voice mail service
provided by your local telephone company. The LED flashes when you have new incoming
messages in the voice mail service. You may need to occasionally reset the indicators if they
remain on after you've retrieved your messages. To reset the indicators, when the phone is
in standby mode press and hold find handset on the base until the paging sound stops
(about 5 seconds).
[36] BASICS
www.uniden.com
BASICS
Once you've programmed your personal access number, you can dial your mailbox with
the touch of a button. When you have messages, simply pick up the handset and press
select/. If you have not entered the access number or it has been deleted, when you press
the select/, No Nu mb e r S to r ed T o s t or e n u mb er pr e ss [M EN U ] appears and you will
hear a beep. The phone returns to standby mode.
UP318BH(DCT6465) OM.book
37 ページ
2003年10月22日 水曜日 午後6時20分
Phonebook
The Phonebook allows you to dial a number using just a few key presses. Your phone stores
names/numbers in the phonebook memory location, and you can search names in
alphabetical order. You have a total of 100 locations that can be used for the phonebook
(including the speed dials) and Caller ID messages.
Storing Phone Numbers, Names, Distinctive
Rings, and Speed Dial
1) When the phone is in standby mode, press phonebook.
2JQPGDQQM
The handset displays the following items:
5GCTEJ=#<㨲㨱?
(1st line) The number of the phonebook locations used
(2nd line) How to search (press the number keypad,
5VQTG=5'.'%6?
ring/vol/∧ or ring/vol/∨)
(3rd line) How to enter the storing operation (press the select/ key)
www.uniden.com
5VQTG'FKV0COG
/QXKGU
5VQTG'FKV0Q
㨫
•Your phone has
100 memory locations
for Caller ID messages
or stored Phonebook
numbers.
•Selecting a speed dial
location where a
number is already
stored releases the
old numbers speed dial
setting. The new
number will be stored
in the speed dial
location.
•When the memory is
full, you will hear a
beep, and M em o ry
F ul l appears. You
cannot store names
and numbers.
•The pause key counts
as one digit. Pressing
redial/pause more
than once increases the
length of the pause
between numbers. Each
pause represents a 2
second delay.
PHONEBOOK [37]
PHONEBOOK
2) Press select/, S to re / Ed i t N am e appears.
3) Enter the name (up to 16 characters) by using the
number keypad (see the "Steps for Entering Names and
Special Characters" on page 39).
If a name is not required, go to step 4. <No Name> will
be used as the name.
4) Press select/ to store the name,
S t or e /E d it N o . appears.
5) Press the number keypad to enter the phone number
(up to 20 digits), press select/ to store the number.
note
UP318BH(DCT6465) OM.book
38 ページ
6)
2003年10月22日 水曜日 午後6時20分
appears. Press ring/vol/∧ or ring/
vol/∨ to move the pointer to one of the Distinctive Ring
options, and then press select/.
D i st in c ti v e R in g
&KUVKPEVKXG4KPI
0Q5GNGEVP
(NKEMGT
If you choose not to store a "Distinctive Ring",
simply select the "No Selectn" option.
7)
appears. Press ring/vol/∧ or ring/vol/∨ to
move the pointer to select the Speed dial location
(10 locations: SPD1-SPD0).
S p ee d D ia l
5RGGF&KCN
0Q5GNGEVP
52&'ORV[
If you choose not to store the name/number as a
Speed Dial, simply select the "No Selectn" option.
8) Press select/. You will hear a confirmation tone, and
D o ne ! appears in the display.
/QXKGU
㨰$GGVJQXGP52&
Chain Dialing
An example of this is a bank account number. Store the account or special number in one of
the phonebook locations. (Refer to "Storing Phone Numbers, Names, Distinctive Rings and
Speed Dial" on page 37). When you call your bank, and you are prompted to enter the
account number, scroll through your phonebook locations until you find your account or
special number, and then press select/.
[38] PHONEBOOK
www.uniden.com
PHONEBOOK
The memory locations in the handset are not limited to phone numbers. You can also store a
group of numbers (up to 20 digits), that you need to enter once your call connects. This is
referred to as Chain Dialing.
UP318BH(DCT6465) OM.book
39 ページ
2003年10月22日 水曜日 午後6時20分
Steps for Entering Names and Special Characters
Refer to the letters on the number keys to select the desired characters. With each press of
a number key (0-9), the displayed character appears in the following order:
upper case letters first, lower case letters next and finally the number corresponding to
the key.
Number of times key is pressed
PHONEBOOK
www.uniden.com
PHONEBOOK [39]
UP318BH(DCT6465) OM.book
40 ページ
note
If the next character
uses the same number
key, you must press
#/→ to move the
cursor over. Otherwise
the next time you press
the number key, it
changes the character
that was previously set.
2003年10月22日 水曜日 午後6時20分
If you make a mistake while entering a name
Use */tone/← or #/→ to move the cursor to the incorrect character.
Press menu/del to erase the wrong character, and then enter the correct character.
To delete all characters, press and hold menu/del.
For example, to enter Movies:
1) When the phone is in standby mode, press phonebook.
2) Press select/,
St o re / Ed i t Na m e
appears.
3) Press 6 once, and then press #/→ to move the cursor to the right.
4) Press 6 six times.
5) Press 8 six times.
6) Press 4 six times.
7) Press 3 five times.
8) Press 7 eight times.
9) When finished, press select/.
To continue to store the telephone number, proceed to step 5 on page 37.
PHONEBOOK
[40] PHONEBOOK
www.uniden.com
UP318BH(DCT6465) OM.book
41 ページ
2003年10月22日 水曜日 午後6時20分
Viewing the Phonebook
Your phone stores names/numbers in the phonebook memory locations, and you can search
names in alphabetical order. You can view the phonebook even while the phone is in use.
1) Press phonebook.
If you recall the phonebook during a call,
S t or e [ S EL EC T ] will not appear.
2JQPGDQQM
5GCTEJ=#<㨲㨱?
5VQTG=5'.'%6?
2) Press ring/vol/∧ or ring/vol/∨, or the number keypad to scroll through the phonebook
locations. Phonebook locations appear in alphabetical order (from first to last when you
press ring/vol/∨, from last to first when you ring/vol/∧).
You can also use letters on the number keys to select the first letter of the desired name.
Press a number key (2-9 and 0) once for the first letter, press twice for the second letter,
and so on. The first location that begins with the letter you entered appears.
For example, to search for "Movies", press 6 once. Press ring/vol/∧ or ring/vol/∨, until
the phonebook location is displayed.
3) To finish viewing numbers, press end (or phonebook during a call).
During a call, don't
press end or the call
will be disconnected.
PHONEBOOK [41]
PHONEBOOK
www.uniden.com
note
UP318BH(DCT6465) OM.book
42 ページ
2003年10月22日 水曜日 午後6時20分
Making Calls Using the Phonebook
From Standby Mode
1) When the phone is in standby mode, select the
phonebook location to dial (see "Viewing the
Phonebook" on page 41).
2) Press talk/flash or speaker to dial the displayed number.
3) To hang up press end.
/QXKGU
㨰$GGVJQXGP52&
From Talk Mode
1)
2)
3)
4)
Press talk/flash or speaker.
Select the phonebook location to dial (see "Viewing the Phonebook" on page 41).
Press select/. The number in the displayed phonebook location is dialed.
To hang up press end.
Speed Dialing
If you store a phone number in a speed dial memory location (10 locations: SPD1 - SPD0),
you can use the speed dialing feature. When the phone is in standby mode, press and hold a
number key (0-9) associated with the speed dial until the phone number appears and then
press talk/flash or speaker. The number stored in the speed dial (SPD1 - SPD0) is dialed.
PHONEBOOK
[42] PHONEBOOK
www.uniden.com
UP318BH(DCT6465) OM.book
43 ページ
2003年10月22日 水曜日 午後6時20分
Editing or Erasing a Stored Name, Phone
Number, Distinctive Ring, and Speed Dial
1) When the phone is in standby mode, press phonebook.
2) Press ring/vol/∧ or ring/vol/∨, or the number keypad
to view the phonebook locations (see "Viewing the
Phonebook" on page 41).
a. Editing the Stored Data
1) When the phonebook location to be edited appears,
press select/. S to re / Ed i t N am e appears.
2) Follow the steps 3 to 7 under "Storing Phone Numbers,
Names, Distinctive Rings, and Speed Dial" on page 37-38
to complete the editing operation.
3) Press select/. You will hear a confirmation tone.
www.uniden.com
5VQTG'FKV0COG
/QXKGU
&GNGVG/GOQT[!
;GU
0Q
PHONEBOOK
b. Deleting the Stored Data
1) When the phonebook location to be deleted appears,
press menu/del.
D e le t e M em or y ? appears.
2) Press ring/vol/∧ or ring/vol/∨ to move the pointer
to Y e s .
3) Press select/. You hear a confirmation tone.
D e le t ed ! appears in the display.
2JQPGDQQM
5GCTEJ=#<㨲㨱?
5VQTG=5'.'%6?
PHONEBOOK [43]
UP318BH(DCT6465) OM.book
44 ページ
2003年10月22日 水曜日 午後6時20分
PHONEBOOK
Memory Dialing (base only)
note
•The 10 memory
locations in the base
are independent from
the handset.
•If you have not
pressed any key for
30 seconds, the phone
returns to standby
mode.
You can store 10 phone numbers in the base, and make
calls with memory dialing from the base.
Storing Phone Numbers
1) Press memory in standby mode.
2) Enter the number you wish to store. (The number
cannot exceed 20 digits.)
3) Press memory. Enter the memory location number (0-9)
on the keypad.
You will hear a confirmation tone.
Making Calls with Memory Dialing
1) Press
(speaker) in standby mode.
2) Press memory. Enter the memory location number (0-9) to dial the number.
Deleting the Stored Data
1) Press memory in standby mode.
2) Press memory again.
3) Enter the memory location number (0-9) you wish to delete.
You will hear a confirmation tone.
[44] PHONEBOOK
www.uniden.com
UP321BH CH16 CallerID.fm
45 ページ
2003年10月23日 木曜日 午後4時22分
You must subscribe to Caller ID services through your local telephone provider to use
these features.
When the telephone rings, the Caller ID feature allows you to view the caller’s name, and
phone number along with the date and time of call. With CIDCW (Caller ID on Call Waiting),
you will hear a call waiting tone while you are on a call, and the Caller ID data is displayed.
To accept the waiting call, press talk/flash (see page 35). Additionally, you can dial a
number stored in the Caller ID list or save data to your Phonebook locations.
Important:
Memory locations for Caller ID messages and Phonebook locations (including Speed Dials)
are common, you can store up to 100 in total. A Caller ID message is not stored when you
have stored 100 of the phonebook locations. The earliest Caller ID message is overwritten
when you have stored 100 of the phonebook locations and Caller ID messages in total.
The date and time received
Caller's name
Caller's phone number
#/
,CPG5OKVJ
1) When the Caller ID message is received, the display shows the caller's phone number
along with the date and time. The incoming call information is stored in the Caller ID
record. If the Caller ID service includes the caller's name, the name will appear in the
display (up to 15 characters).
You may receive any one of the following messages:
When invalid data is received
I n co m pl e te D a ta
P r iv a te Na me
When a private name is received
When a private number is received P r iv a te Nu mb e r
When a unknown name is received U n kn o wn Na me
When a unknown number is received U n kn o wn Nu mb e r
www.uniden.com
note
•If you answer a call
before the Caller ID
message is received
(for example, before
the second ring), the
Caller ID message will
not appear.
•When the call is
received via a
telephone company
that does not offer
Caller ID service,
the caller’s phone
number and name
does not appear.
(This includes some
international calls.)
•When the call is via a
private branch
exchange (PBX),
the caller's phone
number and name may
not appear.
CALLER ID [45]
CALLER ID
Caller ID and CIDCW (Caller ID on Call Waiting)
UP318BH(DCT6465) OM.book
46 ページ
2003年10月22日 水曜日 午後6時20分
Ta l k .
CALLER ID
2) When you pick up the phone, the display changes to
(AutoTalk feature is set to on).
Data errors appear as "❚".
note
•The number of calls
from the same Caller
ID appears next to
the received time.
Once you view the
new message, the
number will be cleared
and disappear.
Viewing the Caller ID List
The Caller ID list stores information for incoming calls - even unanswered calls.
You can store 100 of the Caller ID messages and Phonebook locations (including Speed
Dials) in total. You can view the Caller ID list during a call or when the phone is in standby
mode.
1) Press call id.
The summary screen appears. The screen shows the number of new messages and
total messages.
2) To view the Caller ID messages in historical order (from new to old or from old to new),
repeatedly press ring/vol/∨ to scroll through the messages from the latest to the
earliest, or ring/vol/∧ to scroll back through the messages.
To view the Caller ID messages with alphabetical search, press the number key pad
(2-9 and 0) with the letter associated with the first letter of the desired message.
Once you view the Caller ID list with alphabetical search, you cannot switch back
to historical order (from new to old or from old to new) unless you exit and re-enter
the operation.
•During a call, don't
press end or the call
will be disconnected.
[46] CALLER ID
3) To finish the viewing operation, press end (or call/id during a call).
www.uniden.com
UP318BH(DCT6465) OM.book
47 ページ
2003年10月22日 水曜日 午後6時20分
note
Deleting Information from the Caller ID List
1) When the phone is in standby mode, view the Caller ID
information to be deleted (see "Viewing the Caller ID
List" on page 46).
2) Press menu/del. De l et e C al l er ID appears.
3) Press ring/vol/∧ or ring/vol/∨ to choose Y es .
4) Press select/. You will hear a confirmation tone.
&GNGVG%CNNGT+&
;GU
0Q
•Standby Mode The handset is not in
use and talk/flash
has not been pressed.
Deleting all Caller ID names/numbers
1) When the phone is in standby mode, press call id.
2) Press menu/del.
De l et e A ll ?
%CNNGT+&
0GY
6QVCN
appears.
3) Press ring/vol/∧ or ring/vol/∨ to choose
Y es .
•Once the Caller ID data
has been deleted, the
information cannot
be retrieved.
&GNGVG#NN!
;GU
0Q
•Talk Mode The handset is not in
the cradle and talk/
flash or speaker has
been pressed enabling
a dial tone. Ta l k
appears on the display.
4) Press select/. You will hear a confirmation tone.
www.uniden.com
CALLER ID [47]
CALLER ID
Deleting a Caller ID Message
UP321BH CH16 CallerID.fm
48 ページ
2003年10月23日 木曜日 午後4時22分
note
Calling a party from the Caller ID list
From Standby mode
•You cannot make a call
from the Caller ID list if
your phone is connected
to a private branch
exchange (PBX).
•When a long distance call
has been set, 1 appears in
the display.
•If a call comes in via a
telephone system that
does not offer Caller ID
service, no information
is stored.
•If the Caller ID message
was received as a private/
unknown number, or the
message does not have
the number, you cannot
store the message in the
Phonebook. If it was
received as private/
unknown name, the
message will be stored as
<No Name>.
•Even if the 100 memory
locations are full, the
message will be stored in
the Phonebook. However,
the message will be
erased from the Caller
ID list.
[48] CALLER ID
1) When the phone is in standby mode, view the Caller ID
message (see "Viewing the Caller ID List" on page 46).
2) Press talk/flash or speaker. The displayed phone number
dials automatically.
#/
,CPG5OKVJ
From Talk mode
1) Press talk/flash or speaker.
2) View the Caller ID message you want to dial (see "Viewing the Caller ID List" on page 46).
3) Press select/. The displayed phone number will be dialed.
Long Distance calls and Area Code Setting/Cancellation
While the present Caller ID information is displayed, pressing */tone/← will place or
remove the prefix "1" in the display to set the call for a long distance call, or pressing #/→
will set or cancel an area code (see page 24).
Storing Caller ID messages in the Phonebook
Messages shown in the Caller ID list can be stored in the phonebook. The phone number and
name of the party on the Caller ID list can be stored in memory.
1) When the phone is in standby mode, view the Caller ID message to be stored.
Then press select/. S t or e /E d it N a me appears.
2) To complete the setting, follow the steps 3-8 in "Storing Phone Numbers, Names,
Distinctive Rings, and Speed dial" on page 37-38.
www.uniden.com
CALLER ID
Using the Caller ID Message List
UP321BH CH16 CallerID.fm
49 ページ
2003年10月23日 木曜日 午後4時22分
Your phone gives you new options for call waiting. At the touch of a button, you can place
the caller on hold, send them to your voice mail service, or conference them into your
current call. You may be required to subscribe to Call Waiting and Call Waiting Deluxe to use
these features. Not all features are available in all areas. Check with your local telephone
company for details.
1) When you receive a Call Waiting call, press menu/del for a list of options.
2) Press ring/vol/∧ or ring/vol/∨ to select
C W D e lu x e
For example:
#UMVQ*QNF
6GNN‫ޓ‬$WU[
(QTYCTF%CNN
press ring/vol/∨ 2 times
(QTYCTF%CNN
#PUYGT&TQR
%QPHGTGPEG
•To activate features,
select C W On / CW D X
O n in the CIDCW
option. See page 24.
•You can also answer a
waiting call
immediately by
pressing talk/flash,
the first caller will be
placed on hold. To
return to the original
caller, press talk/
flash again.
and then press select/.
3) Press ring/vol/∧ or ring/vol/∨ or the number keypad (1-7) to select an option.
press ring/vol/∨ 4 times
note
%QPHGTGPEG
&TQR(KTUV
&TQR.CUV
•If you don't press a
key within 30 seconds
while in the operation,
the phone goes back
to the original call.
3) Press select/. A confirmation screen will appear, and returns back to the call.
Your phone is pre-programmed with seven call waiting options. You may select to ask the
calling party to hold, send them a busy message, forward them to your voice mail, or answer
and drop the first caller. You may also select to conference them into the current call or, at
any time, choose to drop the first or drop the last caller. Check with your local telephone
company for a full list of options.
www.uniden.com
CALLER ID [49]
CALLER ID
Call Waiting Deluxe Features
UP318BH(DCT6465) OM.book
50 ページ
2003年10月22日 水曜日 午後6時20分
Expanding Your Phone
note
•To use the DCX640,
register it to the
original base.
•Save this manual for
detailed operation.
Your phone supports up to 4 handsets
(including any handsets supplied with your
phone). You can now place a fully-featured
cordless handset anywhere AC power is
available to connect the handset charger.
Up to 2 handsets can be used for an outside
and/or intercom call.
Effective combinations, for example:
- 4-way conferencing (the base, 2 handsets, and one outside line), while on an intercom call
using the other 2 handsets.
IMPORTANT:
• If you purchase a DCX640 extra handset, please register the handset to the original/main
base before use. The DCX640 will not operate until it is registered.
• If you change a Global setting in one handset, you change that particular setting for all
registered handsets. All other settings (not included under Global Setup), must be set
separately through each handset.
Connecting the Charger
•Charge the handset
battery pack for at
least 15-20 hours
before using your new
cordless telephone for
the first time.
1) Connect the AC adapter to the DC IN 9V jack and to a
standard 120V AC wall outlet.
2) Set the charger on a desk or tabletop, and place the
handset in the charger with the keypad facing forward.
(See "B. Install the rechargeable battery pack into the
handset" on page 12).
[50] EXPANDING YOUR PHONE
www.uniden.com
E X PAN D I N G Y O U R
PHONE
•All of the handsets
ring when a call
is received.
4 Multi-Handset Expandability
UP318BH(DCT6465) OM.book
51 ページ
2003年10月22日 水曜日 午後6時20分
Register the Handset to the Base
If you purchase an extra handset, you need to register the handset to the base before
use. Only one handset can be registered at a time.
The handset ID for the supplied handset(s) was assigned at
the factory. Factory-registered handsets have Handset #1 or
#2 in the display (#2 for models that have two handsets in
packaging). When you register additional handset to the
base, the handset ID will be assigned.
•Standby Mode The handset is not in
use and talk/flash
has not been pressed.
1
Charge the handset
for 15-20 hours.
•An extra handset can
be registered when
the main base is in
standby mode.
Extra Handset
Charger
2) Place the extra handset in the main base unit
to begin registration.
2
Extra Handset
3) While the handset is registering, H an d se t
Place the extra
R e gi s te r in g will appear in the LCD.
handset in the main
When R eg i st r at io n C o mp l et e is displayed, base to register.
the handset has been registered to the base.
If R e gi s tr at i on Fa i le d appears, please try
these steps again.
4GIKUVTCVKQP
%QORNGVG
Main Base
4
Extra Handset
3
www.uniden.com
+
Main Base
Charger
EXPANDING YOUR PHONE [51]
E X PAN D I N G Y O U R
PHONE
1) Before registering the extra handset,
the battery pack must be charged for
15-20 hours.
2NCEGJCPFUGV
QPOCKPDCUG
VQTGIKUVGT
note
UP318BH(DCT6465) OM.book
52 ページ
2003年10月22日 水曜日 午後6時20分
Using the DirectLink Mode
note
Two handsets can be
in Direct Link mode
while other handsets
are in use.
To use this feature, you must enter the two handsets
into the DirectLink mode first.
To enter the DirectLink mode, see page 20.
DirectLink Call
2) Select the handset to which you wish to DirectLink with
by pressing the number keys (1-4). Your handset will
then page the other handset.
3) On the receiving handset, press talk/flash, or if Any Key
Answer is on, press any number key,*/tone/←, or #/→.
570#
*CPFUGV
&KTGEV.KPM/QFG
6Q&KTGEV.KPM
CJCPFUGV
RTGUU=?
&KTGEV.KPM
*CPFUGV
4) When you finish your conversation, press end on either
handset. Return the handset to the cradle, or press
menu/del, and then select/ to return to normal
standby mode (canceling DirectLink mode).
[52] EXPANDING YOUR PHONE
www.uniden.com
E X PAN D I N G Y O U R
PHONE
1) When the phone is in the DirectLink standby mode, press
talk/flash (example of DirectLink from handset #1).
UP318BH(DCT6465) OM.book
53 ページ
2003年10月22日 水曜日 午後6時20分
4-Way Conferencing
Fourth person, at either the handset or the base, may be added to the conference call. For
example, to add a fourth party to an ongoing conference call at the base or another handset,
press talk/flash on the fourth party's handset (or
(speaker) on the base). To remove either
caller from your conversation, press end on the party's handset (or
(speaker) on the base).
The other parties will still be connected to the call.
Intercom and Call Transfer features are available for your phone.
Intercom
•If any of the following
occurs while selecting
the other handset
(or the base), the
operation will
be canceled.
From handset to handset or to the base
1) Press hold/transfer/int'com in standby mode.
6QKPVGTEQO
*CPFUGV
$CUG
3) On the receiving handset (or the base), to answer the call, press talk/flash or hold/
transfer/int'com (or intercom or
(speaker) on the base). Or press any number key,
/tone/←, or #/→ (when Any Key Answer is on), or pick up the handset from the cradle
*(when
AutoTalk is on).
4) To hang up the intercom call, press end on either handset (or intercom on the base).
www.uniden.com
- Press talk/flash
or speaker.
- Receive an outside/
intercom call or page.
•When the party does
not answer within one
minute, the operation
is canceled.
•Standby Mode The handset is not in
use and talk/flash
has not been pressed.
EXPANDING YOUR PHONE [53]
E X PAN D I N G Y O U R
PHONE
•If the party is busy or
out of range, the
handset returns to
standby mode.
Intercom/Call Transfer Feature
2) Select the base or the handset you want to talk with
from the selection list within 30 seconds. To select the
handset (or the base), press ring/vol/∧ or ring/vol/∨,
and then press select/. If you select A l l , all handsets
and the base will be paged. An intercom tone sounds.
note
UP318BH(DCT6465) OM.book
54 ページ
2003年10月22日 水曜日 午後6時20分
From the base to a handset
1) Press intercom on the base in standby mode.
2) Select the handset you want to talk with by pressing the number key (1-4).
To page all the handsets press */tone.
3) Follow the steps 3-4 under "From handset to handset or to the base."
Call Transfer Feature
From handset to handset or to the base
note
For model number
verification, contact
Uniden Customer Service
or visit our website
www.uniden. com
2) Select a handset or the base to transfer the call within
10 seconds. (Refer to step 2 in the intercom section on
page 53).
The call will automatically be placed on hold, and an
intercom tone sounds.
To cancel the transfer, press talk/flash or speaker on the
*QNFVQVTCPUHGT
*CPFUGV
$CUG
initiating handset.
3) On the receiving handset, press talk/flash or hold/transfer/int'com (or
(speaker) or
intercom on the base) to answer the page. Or press any number key, */tone/←, or #/→
(when Any Key Answer is on), or pick up the handset from the cradle (when Auto Talk
is on).
4) To speak to the caller, press talk/flash (or
[54] EXPANDING YOUR PHONE
(speaker) on the base) on the receiving handset.
www.uniden.com
E X PAN D I N G Y O U R
PHONE
1) During a call, press hold/transfer/int'com on the handset.
UP318BH(DCT6465) OM.book
55 ページ
2003年10月22日 水曜日 午後6時20分
From the base to a handset
1) During a call, press intercom on the base. The call will automatically be placed on hold.
2) Select the handset you want to talk with by pressing the number key (1-4). To page all
the handsets press */tone. An intercom tone sounds. To cancel the transfer, press
intercom or
(speaker) on the base.
3) On the receiving handset, press talk/flash or hold/transfer/int'com to answer the page.
Or press any number key, */tone/←, or #/→ (when Any Key Answer is On), or pick up
the handset from the cradle (when AutoTalk is On). The intercom mode is activated, but
the caller is still on hold.
4) To speak to the caller, press talk/flash or speaker on the receiving handset.
If the base unit is replaced with a different base from this same series of cordless models,
you must clear handset (s) and base identification numbers. To do this, select "System
Reset" from handsets display menu option list (see page 26 for guidance).
www.uniden.com
EXPANDING YOUR PHONE [55]
E X PAN D I N G Y O U R
PHONE
Replacing the Base
UP318BH(DCT6465) OM.book
56 ページ
2003年10月22日 水曜日 午後6時20分
Changing the Digital Security Code
The digital security code is an identification code used to connect the handset and the base
unit. Normally, setting the code is not necessary. In the rare situation that you suspect
another cordless telephone is using the same security code, you can change the code.
To change the digital security code:
1. Perform the "System Reset" menu options ("De-register the Handset" and
"Replacing the Base Setting") for all the handsets you have (see page 26).
2. To register all the handsets do the following steps:
1) Place a handset, one at a time in the base.
2) Registration starts automatically.
While registering Ha n ds e t R eg i st er i ng appears in the display.
3) When the registration is complete, R eg i st ra t io n C o mp l et e appears in the display.
4) Repeat steps 1 - 3 for another handsets.
If the registration fails, R e gi st r at i on Fa i le d appears in the display. Try the steps
above again.
Installing the Beltclip
To attach the beltclip
Insert the beltclip into the holes on each side of the handset.
Press down until it clicks.
To remove the beltclip
Pull either side of the beltclip to release the tabs from the holes.
Your phone may be used with an optional headset, the Uniden HS 910
or HS 915. To use the optional headset, insert the headset plug into
the headset jack, and your phone is ready for hands-free conversations.
Headsets may be purchased by calling, the Uniden Parts Department at
1-800-554-3988 or by visiting www.uniden.com
[56] ADDITIONAL INFORMATION
www.uniden.com
ADDITIONAL
INFORMATION
Headset Installation
UP318BH(DCT6465) OM.book
57 ページ
2003年10月22日 水曜日 午後6時20分
Note on Power Sources
Battery replacement and handling
When the operating time becomes short, even after a battery is recharged, please replace
the battery. With normal usage, your battery should last about one year. Please contact your
place of purchase or the Uniden Parts Department for a replacement battery.
Warning
To avoid the risk of personal injury or property damage from fire or electrical shock, only use
the Uniden battery model and Uniden adapter model specifically designated for this product.
Power Failure
During the period that the power is off, you will not be able to make or receive calls with
the telephone.
•
•
•
•
Caution
Use only the specified Uniden battery pack (BT-446).
Do not remove the batteries from the handset to charge them.
Never throw the battery into a fire, disassemble them, or heat them.
Do not remove or damage the battery casing.
Maintenance
Caution
Do not use paint thinner, benzene, alcohol, or other chemical products.
Doing so may discolor the surface of the telephone and damage the finish.
www.uniden.com
ADDITIONAL INFORMATION [57]
ADDITIONAL
INFORMATION
To maintain a good charge, it is important to clean the charging contacts on both the
handset and the base unit once a month. Using water only, dampen a cloth to clean the
charging contacts. Then make sure to go back over the charging contacts with a dry cloth.
UP318BH(DCT6465) OM.book
58 ページ
2003年10月22日 水曜日 午後6時20分
General Information
The phone complies with FCC Parts 15 and 68. Operating temperature: 0 °C to +50 °C (+32 °F
to +122 °F)
AC Adapter Information
AC Adapter part number:
AD-830 for the base
Input Voltage:
Output Voltage:
120 AC 60Hz
9V DC 400mA
AD-310 for the charger
(DCT6465-2 only)
120V AC 60Hz
9V DC 210mA
Battery Information
Battery part number:
Capacity:
BT-446
800mAh, 3.6V
• To avoid damage to the phone use only Uniden AD-830 and BT-446 with your phone.
• If the handset is left off of the base, the actual Talk mode duration will be reduced
respective to the amount of time the handset is off the base.
Recharge your phone on a regular basis by returning the handset to the base after each
phone call. When the operating time becomes short, even after the battery is recharged,
please replace the battery. With normal usage, the battery should last about one year.
Specifications, features, and availability of optional accessories are all subject to change
without prior notice.
[58] ADDITIONAL INFORMATION
www.uniden.com
ADDITIONAL
INFORMATION
A replacement Uniden adapter or battery may be purchased by contacting the Uniden Parts
Department (800) 554-3988. Hours are from 8:00 a.m. to 5:00 p.m. Central Time, Monday
through Friday, or www.uniden.com.
UP318BH(DCT6465) OM.book
59 ページ
2003年10月22日 水曜日 午後6時20分
If your phone is not performing to your expectations, please try these simple steps first.
Symptom
Suggestion
• Make sure the AC adapter is plugged into the base or the charger (for DCT6465-2 only) and wall
The charge LED won't illuminate outlet.
• Make sure the handset is properly seated in the cradle.
when the handset is placed in
• Make sure the charging contacts on the handset and the base or the charger (for DCT646-2
the cradle.
only) are clean.
The audio sounds weak.
• Move the handset and/or base to a different location away from and/or scratchy metal objects
or appliances and try again.
• Make sure that you are not too far from the base.
Can't make or receive calls.
• Check both ends of the base telephone line cord.
• Make sure the AC adapter is plugged into the base and wall outlet.
• Disconnect the AC adapter for a few minutes, and then reconnect it.
• Remove the base ID (see "Replacing the Base Setting" on page 26) and register the handset
(see "Register the Handset to the Base" on page 51).
• Make sure that you are not too far from the base.
• If an outside call is already established, you can not be able to make another outside call.
The handset doesn't ring or
receive a page.
• Charge the batteries in the handset for 15-20 hours by placing the handset on the base or
charging cradle.
• The handset may be too far away from the base unit.
• Place the base unit away from appliances or metal objects.
• Remove the base ID (see "Replacing the Base Setting" on page 26) and register the handset
(see "Register the Handset to the Base" on page 51).
Un a va i la b le appears in
the display.
www.uniden.com
• Make sure that another handset(s) or the base is not in use, and try the phone again.
• Make sure that you are not too far from the base.
TROUBLESHOOTING [59]
TROUBLESHOOTING
Troubleshooting
UP318BH(DCT6465) OM.book
60 ページ
2003年10月22日 水曜日 午後6時20分
Suggestion
Severe noise interference.
• Keep the handset away from microwave ovens, computers, remote control toys,
wireless microphones, alarm systems, intercoms, room monitors, fluorescent lights,
and electrical appliances.
• Move to another location or turn off the source of interference.
The Caller ID does not display.
• The handset was picked up before the second ring.
• The call was placed through a switchboard.
• Call your local telephone company to verify your Caller ID service is current.
Voice Message Indication does
not work.
• Contact your local telephone company to make sure that your telephone receives FSK or SDT
message signaling.
• Charge the battery pack for 15-20 hours.
You cannot register the handset
• Remove the base ID (see "Replacing the Base Setting" on page 26) and register the handset
at the base.
(see "Register the Handset to the Base" on page 51).
The handset doesn't
communicate with the
other handsets.
• Remove the base ID (see "Replacing the Base Setting" on page 26) and register the handset
(see "Register the Handset to the Base" on page 51).
• Make sure that you have registered all handsets.
An extra handset can't join
the conversation.
• Make sure there are not 2 handsets already using the 3-way conference feature.
You cannot make an intercom
call with another handset.
• Make sure that the receiving handset is not in use.
If you still have a problem.
• Call our customer hotline at 1-800-297-1023.
[60] TROUBLESHOOTING
www.uniden.com
TROUBLESHOOTING
Symptom
UP317BH CH21 LiquidDMG.fm
61 ページ
2003年10月23日 木曜日 午前10時20分
Moisture and liquid can damage your cordless phone. In case of accidental submersion, please read the following steps.
Case
If the handset or base is exposed to
moisture or liquid, but only affects the
exterior plastic housing.
If moisture or liquid has entered the
plastic-housing (i.e. liquid can be heard
in the phone or liquid has entered the
handset battery compartment or vent
openings on the base).
www.uniden.com
Action
Wipe off the liquid, and use as normal.
Handset:
1) Remove the battery cover and leave it off for ventilation.
2) Remove the battery pack by disconnecting.
3) Leave the battery cover off and the battery pack disconnected for at least 3 days.
4) Once the handset is completely dry, reconnect the battery pack and the battery cover.
5) Recharge the handset's battery pack for 20 hours before using again.
Base:
1) Disconnect the AC adapter from the base unit, cutting off electrical power.
2) Disconnect the telephone cord from the base unit.
3) Let dry for at least 3 days.
IMPORTANT: You must unplug the telephone line while recharging the battery pack to
avoid charge interruption.
CAUTION:
DO NOT use a microwave oven to speed up the drying process. This will cause permanent
damage to the handset, base and the microwave oven.
After following these steps, if your cordless telephone does not work, please send to:
Uniden America Corporation
Parts and Service Division
4700 Amon Carter Blvd.
Ft. Worth TX 76155
1-800-554-3988. Monday through Friday
8 a.m. to 5 p.m. CST
TROUBLESHOOTING [61]
TROUBLESHOOTING
Liquid Damage
UP318BH(DCT6465) OM.book
62 ページ
2003年10月22日 水曜日 午後6時20分
Precautions!
Before you read anything else, please observe the following:
Warning!
Uniden America Corporation DOES NOT represent this unit to be
waterproof. To reduce the risk of fire, electrical shock, or damage to the
unit, DO NOT expose this unit to rain or moisture.
Rechargeable Nickel-Metal-Hydride Battery Warning
• This equipment contains a rechargeable Nickel-Metal-Hydride battery.
• Nickel is a chemical known to state of California to cause cancer.
• The rechargeable Nickel-Metal-Hydride battery contained in this
equipment may explode if disposed of in a fire.
• Do not short-circuit the battery.
• Do not charge the rechargeable Nickel-Metal-Hydride battery used in
this equipment in any charger other than the one designed to charge
this battery as specified in the owner's manual. Using another charger
may damage the battery or cause the battery to explode.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
Uniden works to reduce lead content in our PVC coated cords in our
products and accessories.
Warning!
The cords on this product and/or accessories contain lead, a chemical
known to the State of California to cause birth defects or other
reproductive harm. Wash hands after handling.
Additional Battery Safety Precautions
When using your telephone equipment, these basic safetyprecautions
should always be followed to reduce the risk of fire, electrical shock, and
injury to persons:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Use a dry
cloth for cleaning without liquid or aerosol cleaners.
4. Do not use this product near water; for example, near a bathtub,
wash bowl, kitchen sink or laundry tub, in a wet basement, or near a
swimming pool.
5. Do not place this product on an unstable cart, stand, or table.
The telephone may fall, causing serious damage to the unit.
6. Slots and openings in the cabinet and the back or bottom are
provided for ventilation. To protect the product from overheating,
these openings must not be blocked or covered.
This product should never be placed near or over a radiator or heat
register. This product should not be placed in a built-in installation
unless proper ventilation is provided.
7. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type
of power supply to your home, consult your dealer or local
power company.
8. Do not allow anything to rest on the power cord. Do not locate this
product where the cord will be damaged by persons walking on it.
9. Do not overload wall outlets and extension cords, as this can result
in the risk of fire or electrical shock.
10. Never push objects of any kind into this product through cabinet
slots, as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electric shock. Never spill liquid
of any kind on the product.
11. To reduce the risk of electric shock, do not disassemble this product.
Take it to qualified service personnel when service or repair work is
required. Opening or removing covers may expose you to dangerous
voltages or other risks. Incorrect reassembly can cause electric shock
when the appliance is subsequently used.
12. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. When the power supply cord is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally when following the
operating instructions. (Adjust only those controls that are
covered by the operating instructions. Improper adjustment of
other controls may result in damage and will often require
extensive repair work by a qualified technician.)
E. If the product has been dropped or the cabinet has
been damaged.
F. If the product exhibits a distinct change in performance.
13. Do not use the telephone to report a gas leak in the vicinity of
the leak.
Caution!
[62] PRECAUTIONS & WARRANTY
To reduce the risk of fire or injury to persons by the battery,
read and follow these instructions:
1. Use only the Uniden battery pack specified in the owner's manual.
2. Do not dispose of the battery pack in a fire. The cell may explode.
Check the Nickel Metal Hydride battery disposal package insert for
disposal instructions.
3. Do not open or mutilate the battery pack. Released electrolyte is
corrosive and may cause damage to the eyes or skin. It may be toxic
if swallowed.
4. Exercise care in handling the battery in order not to short the battery
with conducting materials such as rings, bracelets, and keys. The
battery or conductor may overheat and cause burns.
5. Charge the battery pack provided with or identified for use with this
product only in accordance with the instructions and limitations
specified in the owners manual provided for this product.
6. Observe proper polarity orientation between the battery pack and
battery charger.
SAVE THESE INSTRUCTIONS!
Important Electrical Considerations
Unplug all electrical appliances when you know an electrical storm is
approaching. Lightning can pass through your household wiringand
damage any device connected to it. This phone is no exception.
The FCC Wants You To Know
Changes or modifications to this product not expressly approved by
Uniden, or operation of this product in any way other than as detailed
by the owner's manual, could void your authority to operate this
product. Your telephone complies with Part 68 of FCC Rules. You
must, upon request, provide the FCC registration number and the REN to
your telephone company. Both numbers are on the base unit.
Note: You must not connect your phone to:
• coin-operated systems
• most electronic key telephone systems
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation. Privacy of
communications, may not be ensured when using this phone.
Range
Your new phone is designed to achieve the maximum possible range by
transmitting and receiving according to the highest specifications set
forth by the FCC. We have rated this phone to operate at a maximum
distance with the qualification that the range depends upon the
environment in which the telephone is used. Many factors limit range,
and it would be impossible to include all the variables in our rating. The
Maximum Range rating of this phone is meant to be used as a means of
comparison against other range claims.
www.uniden.com
PRECAUTIONS &
WA R R A N T Y
Rechargeable Nickel-Metal-Hydride
Batteries Must Be Recycled or
Disposed of Properly
Important Safety Instructions
UP318BH(DCT6465) OM.book
63 ページ
2003年10月22日 水曜日 午後6時20分
Telephone Line Problems
The FCC has granted the telephone company the right to disconnect
service in the event that your phone causes problems on the telephone
line. Also, the telephone company may make changes in facilities and
services which may affect the operation of your unit. However, your
telephone company must give adequate notice in writing prior to such
actions to allow you time for making necessary arrangements to
continue uninterrupted service. If you are having trouble with your
telephone service, you must first disconnect your phone to determine if
it is the cause of your problem. If you determine that it is the cause, you
must leave it disconnected until the trouble has been corrected.
Radio Interference
More than One Cordless Telephone
If you want to use more than one cordless telephone in your home, they
must operate on different channels. Press the channel key to select a
channel that provides the clearest communication.
Cordless Telephone Privacy
Cordless telephones are radio devices. Communications between the
handset and base of your cordless telephone are accomplished by means
of radio waves which are broadcast over the open airways.
Because of the inherent physical properties of radio waves, your
communications can be received by radio receiving devices other than
your own cordless telephone unit. Consequently, any communications
using your cordless telephone may not be private.
One Year Limited Warranty
Selecting a Location
Important: Evidence of original purchase is required for warranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION ("Uniden") ELEMENTS OF
WARRANTY: Uniden warrants, for one year, to the original retail owner,
this Uniden Product to be free from defects in materials and
craftsmanship with only the limitations or exclusions set out below.
Before choosing a location for your new phone, there are some
important guidelines you should consider:
• The location should be close to both a phone jack and continuous
power outlet. (A continuous power outlet is an AC outlet which does
not have a switch to interrupt its power.)
• Keep the base and handset away from sources of electrical noise such
as motors or fluorescent lighting.
• Be sure there is sufficient space to fully extend the base antenna.
• The base can be placed on a desk or tabletop or mounted on a
standard telephone wall plate.
• You should charge your new phone for 15-20 hours before completing
the installation or using the handset.
Telephone Line Outlets
There are two types of phone outlets:
Modular Jack
Most phone equipment available now uses modular jacks. Phone cords
are fitted with a molded plastic connector which plugs into this type of
jack. If you do not have modular phone jacks, contact your local
telephone company for information about their installation.
Hardwired Jack
Some equipment is wired directly to a phone jack, and these types of
installations require a modular jack converter. This type of installation is
not difficult; however, you should contact your Uniden telephone dealer
or a telephone supply store for advice about the proper adapter or
converter for your particular situation.
Connecting the Telephone Cords
Consider these safety guidelines before connecting the telephone cords:
Caution!
• Never install telephone wiring during a lightning storm.
• Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected.
• Use caution when installing or modifying telephone lines.
Applying Power to the Base
This phone requires an AC outlet, without a switch to interrupt power,
and the included AC adapter. To relieve strain on the DC plug when the
phone is placed on a desk or table, wrap the power cord around the
strain relief notch on the bottom of the base.
NOTE: Place the power cord so that it does not create a trip hazard, or
where it could become chafed and create a fire or other
electrical hazards.
WARRANTY DURATION: This warranty to the original user shall terminate
and be of no further effect 12 months after the date of original retail
sale. The warranty is invalid if the Product is
(A) damaged or not maintained as reasonable or necessary, (B)
modified, altered, or used as part of any conversion kits, subassemblies,
or any configurations not sold by Uniden, (C) improperly installed, (D)
serviced or repaired by someone other than an authorized Uniden service
center for a defect or malfunction covered by this warranty, (E) used in
any conjunction with equipment or parts or as part of any system not
manufactured by Uniden, or (F) installed or programmed by anyone
other than as detailed by the owner's manual for this product.
STATEMENT OF REMEDY: In the event that the product does not conform
to this warranty at any time while this warranty is in effect, warrantor
will either, at its option, repair or replace the defective unit and return
it to you without charge for parts, service, or any other cost (except
shipping and handling) incurred by warrantor or its representatives in
connection with the performance of this warranty. Warrantor, at its
option, may replace the unit with a new or refurbished unit. THE
LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE
WARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEU OF AND
EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHATSOEVER,
WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW,
INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THIS
WARRANTY DOES NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR
PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do
not allow this exclusion or limitation of incidental or consequential
damages so the above limitation or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and you
may also have other rights which vary from state to state. This warranty
is void outside the United States of America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, after
following the instructions in the owner's manual you are certain that the
Product is defective, pack the Product carefully (preferably in its original
packaging). The Product should include all parts and accessories
originally packaged with the Product. Include evidence of original
purchase and a note describing the defect that has caused you to return
it. The Product should be shipped freight prepaid, by traceable means,
to warrantor at:
Uniden America Corporation
Parts and Service Division
4700 Amon Carter Blvd.
Fort Worth, TX 76155
(800) 297-1023, 8 a.m. to 5 p.m. CST, Monday through Friday
www.uniden.com
PRECAUTIONS & WARRANTY [63]
PRECAUTIONS &
WA R R A N T Y
Radio interference may occasionally cause buzzing and humming in your
cordless handset, or clicking noises in the base. This interference is
caused by external sources such as TV, refrigerator, vacuum cleaner,
fluorescent lighting, or electrical storm. Your unit is NOT DEFECTIVE. If
these noises continue and are too distracting, please check around your
home to see what appliances may be causing the problem. In addition,
we recommend that the base not be plugged into a circuit that also
powers a major appliance because of the potential for interference. Be
certain that the antenna on the unit is fully extended when needed.
In the unlikely event that you consistently hear other voices or
distracting transmissions on your phone, you may be receiving radio
signals from another cordless telephone or other source of interference.
If you cannot eliminate this type of interference, you need to change to
a different channel.
Finally, it should be noted that some cordless telephones operate at
frequencies that may cause interference to nearby TVs and VCRs. To
minimize or prevent such interference, the base of the cordless
telephone should not be placed near or on top of a TV or VCR. If
interference is experienced, moving the cordless telephone farther away
from the TV or VCR will often reduce or eliminate the interference.
Installation Considerations
UP318BH(DCT6465) OM.book
64 ページ
2003年10月22日 水曜日 午後6時20分
I.C. Notice
TERMINAL EQUIPMENT
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The abbreviation, IC, before the registration number
signifies that registration was performed based on a Declaration of Conformity indicating that Industry
Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is marked on the equipment itself. The
REN assigned to each terminal equipment provides an indication of the maximum number of terminals
allowed to be connected to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of
all the devices does not exceed five.
RADIO EQUIPMENT
The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications
were met.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device. "Privacy of
communications may not be ensured when using this telephone".
I.C. NOTICE
[64] I.C. NOTICE
www.uniden.com
UP318BH(DCT6465) OM.book
65 ページ
2003年10月22日 水曜日 午後6時20分
Index
A
Anykey answer . . . . . . . . . . . . . 23
Area code . . . . . . . . . . . . . . . . 24
AutoTalk . . . . . . . . . . . . . . . . . 22
B
Banner . . . . . . . . . . . . . . .
Battery
Preparing and charging . .
Replacement and handling
Beltclip . . . . . . . . . . . . . .
. . . 12
. . . 57
. . . 56
C
Caller ID
Caller ID service .
Calling . . . . . . .
Call Waiting . . . .
Deleting . . . . . .
Setting . . . . . . .
Storing . . . . . . .
Using . . . . . . . .
Viewing . . . . . . .
Call transfer feature
Chain dialing . . . . .
CIDCW . . . . . . . . .
CWDX . . . . . . . . . .
Clarity Booster. . . .
Clock . . . . . . . . . .
Copy phonebook. . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
www.uniden.com
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . 23
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
45
48
35
47
24
48
48
46
54
38
45
49
33
24
25
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
24
49
26
25
56
20
22
E, F, G, H
Earpiece volume . . . . . .
Edit voice mail . . . . . . .
Expanding your phone . .
General information . . .
Grobal setup . . . . . . . .
Hands-free conversation
Handset setup . . . . . . .
Headset installation . . .
P, Q
Package contents
Phonebook
Editing . . . . .
Erasing . . . . .
Making calls . .
Storing . . . . .
Viewing . . . . .
Precautions . . . .
Privacy Mode . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 43
. 43
. 42
. 37
. 41
. 62
. 33
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
30
21
50
58
24
27
21
56
R
Receiving a call . . .
Redialing a call. . . .
Register the handset
Replacing Base . . . .
Ringer volume . . . .
Room Monitor. . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 27
. 28
. 51
. 55
. 30
. 21
I, J, K, L
I.C. Notice. . . . . . . . . . . . . .
Important safety instructions .
Intercom . . . . . . . . . . . . . . .
Key touch tone. . . . . . . . . . .
Language . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
64
62
53
23
23
S
Setting up
base unit . . . .
extra handset .
handset . . . . .
Speed dialing . . .
System reset . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 14
. 50
. 12
. 42
. 26
M, N, O
Maintenance . . .
Making a call . . .
Mute . . . . . . . .
New message LED
.
.
.
.
.
.
.
.
57
27
31
36
T, U, V, W, X, Y, Z
Transferring a call . . .
Troubleshooting . . . .
Voice Mail . . . . . . . .
Voice Mail Tone . . .
Programming . . . .
Warranty . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 53
. 59
. 36
. 26
. 21
. 63
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. . . . . . . . . . . .1
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
INDEX
[65]
I ND E X
0-9
3-way conferencing . . . . . . . . . 33
20 ring options . . . . . . . . . . . . 22
D
Day & Time . . . . . . . . . . . .
Deluxe Call Waiting features .
De-register the handset . . . .
Dialing mode . . . . . . . . . . .
Digital security code . . . . . .
Direct link . . . . . . . . . . . . .
Distinctive ringer . . . . . . . .
UP318BH(DCT6465) OM.book
66 ページ
2003年10月22日 水曜日 午後6時20分
Memory List
Name
Phone No.
[66] MEMORY LIST
Name
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
Name
Phone No.
Phone No.
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
www.uniden.com
MEMORY LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
UP318BH(DCT6465) OM.book
67 ページ
2003年10月22日 水曜日 午後6時34分
Memo
www.uniden.com
[67]
UP318BH(DCT6465) OM.book
68 ページ
2003年10月22日 水曜日 午後6時34分
Memo
[68]
www.uniden.com
UP318BH(DCT6465) OM.book
69 ページ
2003年10月22日 水曜日 午後6時34分
At Uniden, we'll take care of you!
If you need any assistance with this product, please call our Customer Hotline at
1-800-297-1023
PLEASE DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
Our Uniden representatives will be happy to help you with any matters regarding
the operation of this unit, available accessories, or any other related matters.
Thank you for purchasing a Uniden product.
Hours: M-F 8:00 AM to 5:00 PM CST.
www.uniden.com
?
For information on the accessibility features of this product, please call
1-800-874-9314 (V/TTY)
May be covered under one or more of the following U.S. patents:
4,523,058 4,595,795 4,797,916 5,381,460 5,426,690 5,434,905
5,491,745 5,493,605 5,533,010 5,574,727 5,581,598 5,650,790
5,660,269 5,661,780 5,663,981 5,671,248 5,696,471 5,717,312
5,732,355 5,754,407 5,758,289 5,768,345 5,787,356 5,794,152
5,801,466 5,825,161 5,864,619 5,893,034 5,912,968 5,915,227
5,929,598 5,930,720 5,960,358 5,987,330 6,044,281 6,070,082
6,125,277 6,253,088 6,314,278 6,418,209

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement