Elko iMM Audio Zone-R Technical data

Elko iMM Audio Zone-R Technical data
ELKO EP Russia
T ECHNICA
A L C ATALOGUE
E
ELKO EP Poland
ELKO EP
ELKO EP Germany
ELKO EP Austria
~
ELKO EP Espana
ELKO EP Slovakia
ELKO EP Hungary
iNELS Asia (China)
ELKO EP, s.r.o.
Palackeho 493 | 769 01 Holesov, Vsetuly | Czech Republic
phone: +420 573 514 223 | fax: +420 573 514 227 | [email protected] | www.inels.com
www.inels.com
Published: 02/2014 / Modifications or amendments reserved / © Copyright ELKO EP, s.r.o. / 1st edition
titulka_inels_425x297_2014.indd 3
20.1.2014 15:42:59
Presentation of ELKO EP Company
ELKO EP, which is based in Holesov, Czech Republic, has been with you on the electrical market
for the past 21 years, covering a wide range of domestic equipment in the field of electrical
installations. The last few years have seen dynamic development of smart wiring, in which our
company has spent seven years developing and launching iNELS smart home system solutions.
We have become market leaders in both modular devices and smart wiring. We‘re developing
products that bring comfort to the customers and safety to the environment.
The Parent ELKO EP company has gradually grown in eight branches - Slovakia, Hungary,
Poland, Russia, the Ukraine, Germany, Austria and most recently Spain. At the same time, we
export to 60 countries around the world, and our products can be found under the world famous
brand names (Schneider Electric, Eaton, HAGER, Siemens, MORS SMITT).
Our work is based on the development and modern technology. In practice, we appreciate you
as our customer, because you‘re receiving good products and smart solutions, which meet your
requirements. Own development facilities, precise production and distribution, all this gives you
the opportunity to use solutions which are both innovative and practical. There are our modern
manufacturing facilities to produce all our products. It was extended over the newest and fastest
SMD line, which means for you guaranteed quality and flexibility of supply.
We have and supervise 80% share of the Czech market and the fourth position in Europe.
Current-year sales growth: 20%
Number of employees in Holešov: 170
Number of employees of ELKO EP Holding: 236
Awards and Recognition:
In 2011, the experts awarded the top products developed in ELKO EP: RF Touch - wireless touch control unit won a Golden Amper, Moravian Electrical and Electronic
Association Award, Innovation Award of the year and PwC Special Award for Innovation. Also iNELS Multimedia - Multimedia control through television, won an award
- honorable mention Grand Prix.
ELKO EP Company provides the possibility for students in technical fields to do their thesis.
In 2012, the company ELKO EP became the number one company in Zlín Region and in the national finals, we won second place.
Our range of products is divided into three product lines - relay (classical modular devices), RF Control (wireless), iNELS BUS system (Bus System). Each product line
has its own technical catalogue, where you can find complete information on individual products.
Product Lines
RELAYS - Modular electronic devices
www.elkoep.com
A wide range of electronic modular devices, which brings new possibilities to home and office control, monitoring and security, as well as
to industrial process control: time relays, installation contactors, staircase automatic switches, time switch clocks, dimmers, thermostats,
power supplies units, control and signalling devices, GSM gates, etc.
iNELS BUS SYSTEM - Intelligent electro-installation system
www.inels.com
iNELS will transform your house into a timeless intelligent household. It will take charge of heating and air-conditioning regulation, lighting
control and switching home appliances, while also providing perfect security for your home. Enjoy controlling your entire house via a TV
screen thanks to iNELS Multimedia (iMM) or use the elegant iNELS Touch Panel (iTP).
iNELS RF Control - Wireless control
www.elkoep.com
A unique wireless control system, which is providing you perfect controlling over your home! The RF Control system enables you to
control functions such as heating, lighting, electrical appliances and window shutters, all with a single touch. No wall cutting, fast and easy
installation, exclusive design of wireless wall switch buttons and other components.
AUDIO/VIDEO
www.elkoep.com
In this group you can find products, which brings you a new dimension of control music, video and home appliances. These are not just
ordinary controllers but products which can be a perfect part of your electro-installation.
LOGUS90 – Home switches and sockets
www.logus90.com
We offer you exclusive switches, sockets and accessories in a standard plastic or metallic design. However, there are also charming luxury
frames from purely natural materials such as genuine wood, metal, granite or hardened glass. Be special!
ETI – Electrical products
www.eti.cz
ETI‘s products bring high-quality, integrated solution for low voltage protection and safety of electrical installation in buildings. We supply
a wide range of low voltage fuses, molded case circuit breakers and isolators, distribution boxes and protection of photovoltaic systems.
ELKO Lighting s.r.o.
www.elkoep.com
We supply not only LED light sources to the market, but we also bring a complex lighting solution. Our goal is to supply quality and
affordable LED light sources and provide a high level of service - always to satisfy our customers!
2
iNELS system advantages
Advantages to classical electrical installation:
Comfort
- dimming function (gradual dim-up/dim-down, soft start, light scenes)
- control via touch-screen (built-in a wall) = complete information
- control via any remote controller (e.g. of your TV or stereo)
- voice control (Sophy unit, responds to your voice commands)
- temperature regulation according to pre-set programs – in each
room individually
- possibility to control by mobile phone, computer and Internet
Automatization
- function is done automatically on the basis of set value (time, temperature,
light intensity, movement of people, wind strength...)
- it is possible to execute several functions on the basis of one command or
event (e.g. when it is dark - INELS rolls shutters down, switches lights on,
increases room temperature and switches TV on, and many others ...)
- arrival/departure functions: after a code is entered (or a card reading) to a
keyboard, system automatically sets electrical appliances according to the
identified user.
Supervision
- system informs you about selected event/events by SMS text message
- anywhere you are and where you can get internet access, you can connect
to your house and supervise or change its state
- integrated security system can be connected to a security agency
Security
- alarm with extended functions is a part of the system
- system is equipped by a keyboard which can be controlled by a code
or by an access card
- all settings and accesses are subjects of passwords in several levels
- protection of a house in case of bad weather (shutters in strong winds or
storm), unexpected events (irregularities in power supply, overload),
natural disasters (sensor for flooding, smoke sensor)
- bio-installation: disconnection of unused electric circuit (e.g. socket
outlets in bedroom while sleeping)
- setting ideal conditions for your children’s sleep (gradual dimming off ,
pleasant temperature, motion monitoring = baby-sitting)
- touchable parts of sensors are supplied by a safe voltage 24V DC
Savings
- regulation of heating / cooling
- time or time-limited switching
- light regulation (possible energy savings up to 10% )
- dependant switching (e.g. when it is dark, for desired temperature etc.)
- blocking of selected appliances in case of high meter tariff
- elimination of unwillingly switched appliances (e.g. when there is no
motion – light switches off )
Design
- modern design of the switches and sockets, thermostat, voice activity
detectors – optional designes of Elegant or LOGUS90
- variety to combine different colours also in multiframe versions
- touch panel screen – unique solution of elegant wireless home
automation
Time for installation
- considerably lower thanks to bus installation (only 2 control wires)
- units are installed and later programmed
Flexibility of changes and extensions
- in future it is possible to add or change units easily
- functions can be changed by PC, also remotely through Internet
Available features for disabled people
- voice and remote control
- sound messages for blind (unit Sophy speaks pre-recorded messages)
- several actions can be done by one command
- control by computer from one spot
10 reasons to choose the iNELS BUS System
1) Ideal solution for new buildings
2) Reduction in energy use up to 30 %
3) Two-wire bus
4) Electro-installation can be extended
5) There is a possibility to change the way of controlling
6) Remote control through Smart phone, tablets or laptop
7) Effective solution - can be combined with a security system
8) Regulation depending on the weather
9) Logical and central functions (e.g. exit button)
10) Media under control (can be also controlled via TV)
3
Choose the right one!
PRICE
OF INSTALLATION
Control using the TV
-
Wireless electro -installation
Tablet
PC / Laptop
Music playback
-
Video cameras
-
Weather station
-
Door communicator
-
Controlling home appliances
-
Touch panel
Control via Smartphone
Detectors
Group controller
Most of you have already built a house or furnished an apartment. If you want to bring life
into your home, we have an elegant wireless solution. As the name implies, the wireless
communication is works with a range of up to 200 m (depending on the internal structure
of the house/apartment and the building materials used.)
The central brain is the RF Touch unit, which can be placed anywhere within range. It‘s
possible not only to program entire system from this unit, but also to control it. Brightly
replaces several thermostats and controllers. Within the system, you have an unlimited
opportunity to add any drivers and place them wherever convenient.
Heating regulation
Controlling blinds
Dimming lights
Energy savings:
Controlling appliances
Controlli
Contro
lling
ng
appliances
Dimming
Dimmin
Dim
ming
g
lights
Controlli
Contro
lling
ng
blinds
Heatin
Hea
ting
g
regulation
Controlling household appl
pp iances
Door
communicator
Weather
station
PRICE
OF INSTALLATION
Group
Gro
up con
contro
trolle
llerr
Detect
Det
ectors
ors
Contro
Con
C
ttroll via
viia
smartphone
Video cameras
Audio Zone
PC /Laptop
Tablet
(outdoor/indoor)
(music playback)
Touch
Touch
panel
Video Zone
(controlling via TV)
Bus electro -installation
Control using the TV
Tablet
Are you building a new house? Then you should consider a bus-based solution. A bus in this
sense is a data conductor that is distributed in the walls across the entire home. As opposed
to a wireless solution, its advantage is range, because up to 10 x 550 m buses can be
distributed in a single building.
PC / Laptop
Music playback
Video cameras
Weather station
Door communicator
Controlling home appliances
Touch panel
Control via Smartphone
Connection to a computer expands the scope of its available functions. This system may be
expanded to include multimedia extensions and can connect third party devices (household
ppliances, A/C, etc.). Control and monitoring the system can be performed via PC, the Internet,
telephone, tablet, etc.
Detectors
The system offers a wider range of of applicable functions. A computer is used to set the
parameters.
Wireless switch
Heating regulation
Controlling blinds
Dimming lights
Energy savings:
Controlling appliances
4
Controlli
Contro
lling
ng
appliances
Dimming
Stmívání
osvětlení
lights
Controlli
Contro
lling
ng
blinds
Regulace
Heating
regulation
vytápění
Wireless
Wirele
ss
switch
Detectors
Detektory
Contro
Con
C
troll via
viia
smartphone
Controlli
Contro
lling
ng hou
housese
hold appliances
Doorr
Doo
communicator
Weatherr
Weathe
station
Video
Vid
eo cam
camera
erass
Audio
Aud
io Zon
Zone
e
PC /Lap
Laptop
top
Tablet
Tab
let
(outdoor/indoor)
(music playback)
Dotykový
Touch
panel
Video
Vid
eo Zon
Zone
e
(controlling via TV)
BUS electro-installation
When you build new house or decide on a complex reconstruction,
the bus solutions of iNELS BUS system represents a unique
solution of electro-installation. The system offers wide range of
functions which bring a pleasant comfort to the users. It also allows
to integrate each technology in the house and brings savings. The
way of controlling can be changed according to user requirements,
the electro-installation can be also extended.
Using of applications to smartphones or tablets is very popular.
They provide efficient and easy way to control your home during
your absence.
What are the benefits of bus controlling?
• Save energy by regulating lighting and heating
• Control of blinds, awnings, exterior or inter-window shutters
• Dimming lights, lighting scenes
• Control of appliances or electrical devices
• Control access gates, garage doors
• Logical and central functions (exit button, ...)
• Manual and automatic control mode
• Preventing undesirable opening of a window or a door
• Responding to the movement of persons (authorized and
unauthorized)
• Remote monitoring via smartphone, tablet or laptop
• Possibility to control via the TV screen
• Integration of third-party devices (cameras, air conditioning, ...)
iNELS BUS System allows you to integrate and control most of
technologies used in your house. It saves your money spent on
energy. You don‘t need to wonder whether it is summer or winter.
Simply set the desired the temperature in the room and your house
automatically knows what to do.
The main idea of intelligent living is saving. The house is able to switch
off the lighting and heating in the room at the time of your absence.
In winter it pulls up the blinds, what allows the house warming by sun
rays. Vice versa in the summer the blinds are pullled down earlier what
reduce the switching frequence of energy-intensive air conditioning.
Flood, temperature, fire or gas leak detector sends command to
close the water supply, gas, ventilation, etc.
The really useful features is also a simulation of presence when you
are on vacation.
To control electro-installation you can use wall-switches, glass touch
switches, touch display, smartphone, tablet or TV screen. So you can
easily control whole house from one place.
Do you like to listen music, to watch movies or to view pictures? All
these data can be available from anywhere in your house thanks to
iNELS Multimedia. In addition you can easily turn off children‘s television
in other room. Whole house can be controlled via TV screen.
Switching
el. appliances
Light
dimming
Heating
regulation
Air conditioning
control
Roller blind
control
Detector
control
RF Remote Control Pilot with OLED display
You can control your house from your sofa in the living room. You can
also change the temperature in selected room or switch off lights in
garage. The iNELS multimedia allows you to view your pictures from
your family holiday, switch on TV in other room for your kids or listen
music. Everything is stored in central storage and it is available from
anywhere in your house.
Touch control unit EST
EST unit with color touch display enables you to regulate the heating,
control RGB light sources and control e.g. light scenes or blinds.
Control electro-installation by Smart phone
You house is all the time under control thanks to applications in
your Smart phones or in tablets. Supported operating systems are
Android, iOS.
5
House switches and sockets
Modern design of the switches and sockets!
The devices can be connected directly to BUS CIB with a combination of multiple frames.
GSB3-40/60/80
WSB3-20
WSB3-40
Wall glass touch
controllers
Wall controller,
2 buttons
Wall controller,
4 buttons
WMR3-11
Contactless
media reader
EST3
Touch display
Design, which takes your breath
Luxus, individuality, beauty. With these words, we can
characterize design of switches, which will catch us on the first
look. Switches, socket outlets and accessories are in plastic
design or resp. plastic with metalic spraying on it. But for the
line LOGUS90 are characteristic a glamorous and luxury materials:
metal, real wood, hardened glass or marble. From these materials
are made frames, which we combine with plastic covers of wallbuttons and sockets-outlets. Covers are offered in white or ivory
colour and with the spraying on it in pearl, ice, aluminium and
grey colour. Resistance of colour against abrasion and scratching
is strictly tested and manufacturer guarantees 10 years warranty
on colour constancy by standard using. Covers can be cleaned
with alcohol without any risk. A matter of interest is that the same
colour is using also by Mercedes or BMW for their car spraying…
With their simplicity, design purity and variety of covers and
frames, the switches fit to any interior.
Standardly 24 combinations are offered. Switches are truthfully
described by its strictly geometric shapes. Thanks to square
symmetry of all frames there is a possibility to install them either
horizontally or verticallly.
Thirty years tradition of production
ELKO EP s.r.o. is an exclusive distributor of Portugeese manufacturer Efapel for this modern line of house switches. Its quality
has been prooved in humid and salty conditions as well as more than thirty years tradition of manufacturing and distributing
electro-installation products over the world. EFAPEL is a highly respected company, which is speciallized in production of units
for low-voltage installations, protection elements for electrical panels, cable systems, connectors, telecommunication panels and
sound systems. The company was established in 1978 and now export into 48 countries worldwide.
Quality and safety
Efapel imaginatively solves not just design of push-buttons,
but is also particular about an inner parts. Quality is visible
throughout all parts. Electro-installers will appreciate devices
made from sturdy resistant plastic without any sharp edges,
for safer manipulation and installation. Construction of the
mechanism provides full isolation between your hands and
dangerous metal parts. Beside long-life and resistance, the
switches are hygienicaly safe even for the youngest ones. The
company holds many quality certificates: e.g. EC Declaration
of Conformity (DoC), RoHS & REACH Compliance Certificates.
6
House switches and sockets
Řada klasických vypínačů a zásuvek LOGUS 90
BASE
AQUARELLA
ANIMATO
CRYSTAL
METALLO
ARBORE
PETRA
Plastic
Metallic design
Plastic
Crystal
Metal
Wood
Stone
BR - White
GE - Ice
MM - Ivory/Ivory
CG - Crystal/Ice
TP - Titanium/Pearl
FP - Beech Wood/Pearl
GG - Granite/Ice
MF - Ivory
PE - Pearl
RG - Yellow//Ice
CP - CRYSTAL/Pearl
IA - Inox/Aluminium
JP - Cherry Tree/Pearl
GP - Granite/Pearl
AL - Aluminium
DG - Green/Ice
CA - Crystal/Aluminium
MS - Mahogany/Grey
GA - Granite/Aluminium
IS - Grey
ZG - Blue/Ice
NA - Walnut Tree/Aluminium
GS - Granite/Grey
CS - Crystal/Grey
JG - Orange/Ice
VG - Red/Ice
OP - Gold/Pearl
QS - Nickel/Grey
US - Aluminium/Grey
RS - Chrome/Grey
Switches and
sockets in design
LOGUS 90 for
classical electroinstallation
* All color combinations series ANIMATO can be found
in the catalogue LOGUS90
BEAUTIFUL,EXTRAORDINARY AND LUXURIOUS
Mechanism of the switch
Covers can be easily changed instead of the old switches or if
you just like a different combination. Any installation of individual
parts together is very easy. Device has four clips, so the frame
fits right into it, other system of mounting is not need. This smart
clips provide smooth operation of switch, even if the wall is not
perfectly flat. Issue with not so straight surface is solved by
"floating rocket“. Device can be mounted into installation box
with classic screws, or with more comfort spacers. Another
advantage provides screwless terminals: wires provide fast
comfortable connection without any need of screwing. Depth
of device is just 20 mm, it means that fits into the box without
any problems. There are doubled terminals on each pole, which
provide multiple connection of mechanism, another terminals are
not need. Holes on the front side of the cover are designed for
electrical functional test of device – removal of whole device is
not need. Of course Logus offering, beside a basic single pole
switch, also double pole switch (two functions) or triple pole
switch (three functions).
7
Catalogue content
Intelligent electro-installation
About us
The benefits of iNELS system
Choose the proper installation!
BUS electro-installation
Houses switches and sockets LOGUS90
Content
Basic overview of system units
Examples of Bus CIB typology
Pictogram description
Basic connection of system with a central unit CU3-01M
2
3
4
5
6–7
8–9
10–11
12
12
13
The base of system iNELS BUS System
CU3-01M,central unit
PS3-100/iNELS, power supply
MI3-02M, external master of bus CIB
BPS3-01M, BPS3-02M, bus separator from power supply
GSM3-01, GSM communicator
14–15
16–17
18
19
20
The peripheral Bus units
Switching actuators
SA3-02M, switching actuator 2-channel
SA3-04M, switching actuator 4-channel
SA3-06M, switching actuator 6-channel
SA3-012M, switching actuator 12-channel
SA3-01B, switching actuator 1-channel
SA3-02B, switching actuator 2-channel
JA3-02B/DC, shutter actuator
8
22
23
24
25
26
26
27
Dimming actuators
DA3-22M, universal dimming actuator 2-channel
LBC3-02M, dimming actuator for florescent lamps 2-channel
EMDC-64M, converter iNELS - DALI/DMX
DCDA-33M/RGB, dimming actuator
RFDA-73M/RGB, dimming actuator
28
29
30
31
32–33
Input units
IM3-20B, IM3-40B, IM3-80B, binary inputs unit
IM3-140M, binary inputs unit
TI3-10B, thermo inputs unit 1-channel
TI3-40B, thermo inputs unit 4-channel
TI3-60M, thermo inputs unit 6-channel
34–35
36
37
37
38
Analog-digital convertors
ADC3-40M, analog-digital converter 4-channel
39
Digital-analog convertors
DAC3-04B, digital-analogue converter 4-channel
DAC3-04M, digital-analogue converter 4-channel
40
41
Wall touch controllers
EST3, the control unit with touch display
GSB3-40, GSB3-60, GSB3-80, glass wall mounted controllers
42–43
44–45
Wall group controllers with low-upstroke control
WSB3-20, WSB3-40, wall controllers
46
Wall card reader
WMR3-11, wall card reader
47
Digital room thermoregulator
IDRT3-1, digital room thermoregulator
48
iNELS Home Control application
iHC
50–51
Accessories iNELS
TELVA 230 V, TELVA 24 V, thermo-drive
TC, TZ, temperature sensors
Product loadability
Case studies
52
53
54–55
56–57
9
Overview of system units
System units
CU3-01M
CU3-02M
Basic element of the system, 2x CIB BUS, 1x EBM BUS, 1x RS232, OLED display,
Ethernet 100 Mbps, 2x analog input, 4x digital inputs, 6-MODULE
Basic element of the system, 2x CIB BUS, 1x EBM BUS, 1x RS232, RF control interface, OLED display,
Ethernet 100 Mbps, 2x analog input, 4x digital inputs, 6-MODULE
MI3-02M, MI3-02M/iNELS2
BPS3-01M, BPS3-02M
GSM3-01M
PS3-100/iNELS
Allows you to expand the system to two
CIB (2 x 32 units), 1-MODULE
Used for impedance segregation of
bus from the power supply, 1-MODULE
GSM gateway for communication iNELS system with
GSM mobile phones, EBM BUS, 3-MODULE
Power supply 100W, supply voltage 85-253 V AC/50-60 Hz,
output voltage DC/max. current: 27.6 V/3.6 A and
12.2 V/0.35 A, 6-MODULE
Switching actuators
SA3-02M
SA3-04M
SA3-06M
SA3-012M
SA3-01B
SA3-02B
2x changeover contacts 16A,
LED indication for relay
status, manual control,
1-MODULE
4x changeover contacts16 A,
LED indication for relay
status, manual control,
3-MODULE
6x changeover contacts 8 A,
LED indication for relay
status, manual control,
3-MODULE
12x switch contacts 8 A,
LED indication for relay
status, manual control,
6-MODULE
1x switch contacts 16 A,
1x thermo input,
mounting into the
installation box
2x changeover contacts 8 A,
1x thermo input,
mounting into the
installation box
Shutter actuator
10
Dimming actuators
JA3-02B/DC
DA3-22M
LBC3-02M
EMDC-64M
DCDA-33M/RGB
Actuators for control and
management of blinds,
shutters, awnings, mounting
into the installation box
Unit for dimming ESL, LED
and RLC load, 2 x 400 VA,
2 control inputs, 1x
thermo input,
3-MODULE
Control unit for electric
ballast, 2x changeover
contacts 16A, 2x analog
signal 1-10 V,LED indication
for relay status,
3-MODULE
INELS-DALI/DMX converter
for controlling electronic
ballasts DALI and DMX
receivers. 3-MODULE
Dimming actuator for LED
and RGB light sources
controlled by varying current.
Control interface DMX, DALI
and CIB. 3-MODULE
Input units
IM3-140M
IM3-20B, IM3-40B
IM3-80B
TI3-10B
TI3-40B
TI3-60M
Input module,
14x binary inputs,
3-MODULE
Binary input modules, 2x/4x
input, 1x thermo input,
mounting into the installation box
Input module,
8x binary input,
1x thermo input, mounting
into the installation box
Unit for connecting,
1x sensor TC, TZ, Ni 1000,
Pt1000 or Pt100,
mounting into the
installation box
Unit for connecting,
4x sensor TC, TZ, Ni 1000,
Pt1000 or Pt100,
mounting into the
installation box
Unit for connecting,
6x sensor TC, TZ, Ni 1000,
Pt1000 or Pt100, 3-MODULE
Converters
Applications iHC
ADC3-40M
DAC3-04B
DAC3-04M
Analog signal converter
on the bus,
4x analog inputs,
3-MODULE
Converter from bus to
signal 0 (1) -10 V,
4 channels, 1 x thermo
input, assembly
the installation box
Converter from bus
to signal 0 (1) -10 V,
4 channels, 1 x thermo
input, 3-MODULE
iHC-MA
iHC-TA
iHC-MI
iHC-TI
Application to control Application to control Application to control Application to control
the system iNELS from the system iNELS from the system iNELS from
the system iNELS
phone with
tablet with Android OS
iPhone
from iPad
Android OS
Wall units and controllers
EST3
The control unit
with touch
display
GSB3-40,
GSB3-60,
GSB3-80
Capacitive glass wall mounted
controllers, 4x/6x/8x buttons,
built-in temperature sensor,
2x AIN/DIN, comes in LOGUS90 design
AUDIO/VIDEO
WSB3-20
WSB3-40
WMR3-11
IDRT3-1
Two-button controller,
built-in temperature sensor,
2x AIN/DIN,
1x indication
LED (red/green)
comes in LOGUS90 design
Four button controller,
built in temperature sensor,
2x AIN/DIN
2x indication
LED (red / green)
comes in LOGUS90 design
Contactless media reader,
1 x switching contact 8 A,
two-button controller,
LOGUS90 design
Digital room
thermoregulator, correcting
of heating/cooling circuits
+5°C/-5°C or it is possible
to adjust directly desired
temperature in °C
an extension of iNELS system is part of a separate catalog AUDIO / VIDEO
eLAN-RF-003
iMM Client
Connection Server
iMM Audio Zone-R
LARA
eLAN-IR-003
The VideoZone player
enabling control of all
functions via TV. Translate IP
protocols of
third-party devices
Translate IP protocols of
third-party devices
The AudioZone player, 3.5mm
stereo Jack audio output
The music and internet
radio player in wall
button size. Integrated
power amplifier 2x 10W,
in LOGUS90 design
Converter Ethernet to IR code,
3 inputs, support IR codes for
the frequency of 20-455 kHz
eLAN-RF-003,
eLAN-RF-Wi-003
Converts commands from
LAN to an RF signal to
control RF actuators
11
Examples of CIB bus topology
Tree structure
Linear structure
central
unit
Circular structure
central
unit
tecentral
unit
Product identification - explanation
DA3-22M
SA3-04M
DAC3-04M
IM3-20B
S
Switch
D Dimming
D Digital
I Input
A
Actuator
A Actuator
A Analogue
M Module
3
3rd generation of iNELS
3 3rd generation of iNELS
C Converter
3 3rd generation of iNELS
-
3 3rd generation of iNELS
-
0
Number of inputs
2 Number of inputs
-
2 Number of inputs
4
Number of outputs
2 Number of outputs
0 Number of inputs
0 Number of outputs
M Modular design
4 Number of outputs
B Box (in a mounting box)
M Modular design
M Modular design
WSB3-40
GSB3-80
TI3-60M
LBC3-02M
G
Glass
W Wall
T Temperature
S
Switch
S Switch
I
B
Button
B Button
3 3rd generation of iNELS
C Controller
3
3rd generation of iNELS
3 3rd generation of iNELS
-
3 3rd generation of iNELS
-
6 Number of inputs
-
-
Input
L Lighting
B Ballast
8
Number of inputs
4 Number of inputs
0 Number of outputs
0 Number of inputs
0
Number of outputs
0 Number of outputs
M Modular design
2 Number of outputs
M Modular design
12
Auxiliary relay
sensors
+
12V EZS
EZS
Pomocné relé
coil 230
230 VV AC/5
AC / 5mA
mA
cívka
switching
contact
spínací
kontakt
např.
eg VS116K
+
24 V battery
baterie
-
OUT OK
U OU TLOW
OV ERLOAD
battery 11 battery
baterie
baterie22
12 V
12 V
RS232
EBM+ EBM- GND
maximum
of 32 units
per line
CIB;
maximum
1Ajednu
per line
CIB CIB
max.
32 jednotek
na jednu
větev
CIB;
max. 1A na
větev
CIB5
CIB6
+ CIB3
+ CIB4
-
+ CIB1
+- CIB2
-
Basic system connection with
the central unit CU3-01M
13
Central unit CU3-01M, CU3-02M
CU3-01M
CU3-02M
EAN code
CU3-01M 8595188132220
CU3-02M 8595188132398
TECHNICAL PARAMETERS
Central units CU3-01M and CU3-02M are the brain of the iNELS system, a "mediator“
between user‘s programming environment and controllers, units and actuators connected
to the bus.
C U3 - 01M , C U2 - 02 M
LED indication:
green LED RUN - indicating the operating status of the unit
red LED ERR - indicating major errors
OLED display:
displays the current status and settings
Type:
color OLED
Resolution:
128x128 / 1:1 aspect ratio
Visible area:
26x26 mm
Controlling:
with a routing buttons
The internal real-time clock:
accuracy: 1s/day at 23 °C
INPUTS
Inputs:
4x NO or NC to GND (-)
It‘s possible to directly connect up to 2 lines of CIB buses in to CU3-01M and CU3-02M, and
on each bus we can connect up to 32 iNELS3 units.
The main difference between CU3-02M and CU3-01M is that CU3-02M is moreover
equipped by RF module which enables communication with selected units from iNELS
RF Control system.
Central units CU-01M(02M) support also peripheral units from iNELS2 thanks to external
master MI3-02M/iNELS2.
User´s project and retentive data are stored in a non-volatile internal memory hereby data
are backed up without the supply voltage. Real time clock (RTC) backup for 10 days.
2 analogue inputs 0÷30
Expandable with modules:
see separate datasheets
Possibility of setting time synchronization via NTP server.
OUTPUTS
Output:
relay output- NC/GND only for EZS
Number of connected units:
(directly to the CU3-01M(02M):
max. 64 (2x32)
Expansion possibilities
up to 576 units
(CU3-01M(02M) and 8x MI3-02M)
external bus master:
Maximum number of units:
max. 32 units to one CIB line
Maximum cable length:
max. 550m (depends on power loss)
System bus EBM
Maximum cable length:
max. 500 m
Number of connected ext. masters:
up to 8 (regards to increasing the cycle turns)
RS232 bus communication
max. 10 m
Ethernet
Connector:
RJ45 on the front panel
Communication speed:
100 Mbps
Indication of the Ethernet:
green - Ethernet communication
yellow - Ethernet speed 100 Mbps
The default IP address:
192.168.1.1
the set-up IP address can be displayed on the screen
R F CO NTRO L I NTE R FACE FO R CU3- 02M
Communication protocol:
transmitting frequency:
Signal transmission methods:
Output for RF antenna:
RF antenna:
Free space range:
The RJ45 Ethernet port‘s connector is located on the front panel of the unit, the transmission
speed is 100 Mbps.
For CU3-01M (02M) it is possible to use 4 potential-free inputs for connecting external
controllers (buttons, switches, sensors, detectors, etc.) and 2 analog inputs 0-30V.
CU3-01M (02M) comes with OLED display that shows the current status and configuration
of CU3-01M (02M) central unit.
COMMUNICATION
CIB
Maximum cable length:
Power supply controlling system - network voltage and the status of the backup battery.
Oasis & RF Touch Compatible
868 MHz
bidirectionally addressed message
SMA connector
1 dB (part of package)
Up to 100 m
CU3-01M (02M) can be controlled using the directional buttons on the front panel.
CU3-01M (02M) in 6-MODULE are designed for mounting into a switchboard on the
EN60715 DIN rail.
P O W E R S U P P LY
Supply voltage:
Ideal supply voltage:
Rated current:
22-30 V DC
27 V DC (from PS3-100/iNELS power supply)
110mA (at 27V DC)
O P E R AT I N G C O N D I T I O N S
Working temperature:
Storage temperature:
Humidity:
Degree of protection:
Overvoltage category:
Degree of pollution:
Operating position:
installation:
Design:
Terminal:
-20 to +55 °C
-25 to +70 °C
max. 80%
IP 20 devices, IP 40 with cover in the switchboard
II.
2
any
to the switching board on the EN60715 DIN rail
6-MODULE
max. 2.5 mm2
DIMENSIONS AND WEIGHT
Dimensions:
Weights:
14
90 x 105 x 65 mm
250 g
CIB Bus installation:
Two-wired bus with an arbitrary topology (not only to be as closed circle).
With its own modulated communications on the DC voltage supply.
One line of CIB bus allows you to connect up max. 32 units of iNELS3, or iNELS2 if you use
external master MI3-02M/iNELS2 with a current load max. 1A.
The current load of one line is max. 1A.
Maximum length of the bus is approximately 550 m (depends on the voltage drop).
Recommended cable :
- twisted shielded pair of cross sectional area 0.8 mm2 for example:
J-Y(ST)Y 2x2x0.8, YCYM 2x2x0.8.
The EBM System Bus:
Used to connect the CU3-01M(02M) central unit with MI3-02M external masters,
MI3-02M/iNELS2, GSM communicator GSM3-01M or converter DALI/DMX EMDC-64M.
Strictly linear topology.
Max. length of the line of bus is 500m.
The EBM bus has to be terminated at both ends.
This part adapted to be inserted between terminals is included into central units packages
and it is necessary to insert between terminals EBM+ and EBM-.
Reccomended cabling:
- UTP CAT5e and higher.
The configurations of units and the whole system are done via Ethernet, through
configuration software - INELS Designer and Manager (hereinafter IDM), which is designed
for operating system MS Windows XP, W7, W8.
CU3-01(02M) can be remotely configured and controlled through external VPN (Virtual
Private Network).
Thanks to webserver integrated in CU3-01M(02M) it is possible to control remotely the
user´s functions through internet browser (PC, smartphone, tablet).
Through CU3-01M(02M), it is possible to remotely upgrade firmware on the connected
bus units.
Supported Software:
- Parameterization, configuration, control and visualization: iNELS Designer & Manager (IDM).
- Promoting free programming according to IEC 61131-3 standard (in preparation).
max. 32 jednote
Auxiliary relay
Pomocné
relémA
coil
230V AC/5
cívka
230 V AC/5
mA
switching
contact
spínací kontakt
e.g. VS116K
+
24
24 VVbattery
baterie
EBM to MI3-02M, MI3-02M/iNELS2,
GSM3-01M or EMDC-64M
battery
baterie1 1 battery
baterie22
12 V
12 V
12 V
+
- CIB1
+ CIB2
-
12 V
např. VS116K
RS232
OVE RLOAD
U OUTLO W
OUT OK
+
12V EZS
iNELS Designer & Manager
iNELS Designer & Manager (IDM) is a programming environment, which is designed for creating
projects for iNELS BUS System‘s installations with the CU3-01M(02M) central unit.
IDM allows management to address the requirements of lighting, blinds or shutters, heating, air
conditioning to the overall supervision of the installation and alarm reporting.
IDM provides the following:
- the possibility of automatic numbering project
- the possibility of entering multiple
- easy-shifting of units for superior masters
conditions
- filtering units by name
- the possibility of comparing different
- filtering units by type (switching, dimming, etc.)
variables
- visualization of the connections between
- sorting units in the list according to their
the elements or element groups
definitions (type, hardware address, unit
- the possibility of adding custom chart icons
name ...)
- the possibility of simulation functions
- visualization of the bus in terms of HW
- comprehensive list of individual connections
addresses‘s number
- the possibility of breaking down elements
- visualization of the bus in terms of the
into logical groups
current load
- the possibility of using timers and counters
- creating of the floors
- transparent management of users and their
- creating layers in these levels (up to 5 layers)
roles
- visibility settings / invisibility of the
- create an unlimited number of heating
individual layers
programs
- assignment of the floor plan or only the base color
- signalizing the status of units
- possibility to zoom in on the floor plan
- the number of units on the web server is not
restricted
15
Power supply PS3-100/iNELS
PS3100/iNELS is a stabilized switching power supply, with the total power of 100 W.
Used to supply central units and external master within intelligent electro-installation iNELS.
Through bus separators from the supply voltage BPS3-01M and BPS3-02M, it supplies
supplies CIB bus lines from which iNELS peripheral units are also powered.
Used in the instrumentation field.
Fixed output voltage DC 27,6 V and DC 12,2 V, galvanically isolated from the mains.
Power source of 27 V and 12 V have a common ground terminal GND.
Electronic short circuit protection, high-capacity and thermal overload, over voltage.
UPS functions - backup of output 24V and 12V on connected batteries.
Recharging the batteries from 27 V source.
Protection battery backup fuse - protection against short circuit and reverse polarity battery.
Continuously adjustable maximum battery charging current.
EAN code
PS3-100/iNELS 8595188131568
Indication of operating and fault conditions 6 LED diodes on the front panel of the power supply.
2 STATUS outputs with open collector for reporting operational status of the source.
Source supplies power to the priority system iNELS, the remaining power is used for
rechargeable batteries.
When the battery is fully discharged, the battery is automatically disconnected from the load.
Description of device functions
PS3-100/iNELS in 6-MODULE version is designed for mounting into a switchboard, on
DIN rail EN60715.
The device consists of several functional blocks.
Example of connection
The basic part is 100 W power supply with 2 output voltage levels.
85 – 253 V AC
Voltage of 27.6 V is used to supply the system iNELS and to recharge the batteries.
Voltage of 12.2 V is for power as intrusion detectors (PZTS) or EPS.
Both voltages are available without interruption during power AC power supply (UPS
function) - assuming they are connected to a backup battery.
+
24 V battery
battery 1 battery 2
12 V
12 V
Other parts of the source circuits are battery backup and recharge, which provide switching
mode connection, charging and disconnecting the battery.
- When in the backup mode, the battery is completely discharged, the circuit is immediately
switched off to avoid deep discharge. The maximum discharge current is also
guarded - when exceeded, the batteries are again disconnected.
- If the switched source is working (oscillating), and its output voltage are greater than
26.9 V, the backup batters are charged by the current, and the maximum value is set by
trimmer on the panel source.
- When charging the yellow LED CHARGE illuminates. The source first feeds the iNELS
system, and the remaining capacity of up to 100 W only recharges the battery.
- If the output is high, this disconnects the charge (the yellow LED CHARGE switches off ).
- Upon further increasing, the load further decreases the voltage source and the load current
also flows from the battery (power supply and battery power to the load together).
Note: If the source is disconnected from the AC network (does not oscillate), and you
connect batteries now, the batters remain disconnected and power outputs are without
power. To activate, the source must be connected to the power supply.
OVERLOAD
UOUT LOW
UOUT OK
+12V OK
CHARGE
OUT
UPRI FAIL
The last part of the unit are signaling circuits and status outputs. STATUS outputs (see
technical data) are equipped with current limiting, so they can switch signaling components
directly without external resistors (e.g. LED, optocouplers or relay coil).
The LED signaling function is given in the table of technical parameters and illustratively
described in seven case studies.
external DC source
+
-
+
12 V
security sensors
16
-
-
+
27 V iNELS
Indication LED
T E C H N I C A L PA R A M E T E R S
AC INPUT
Power supply:
Power load (apparent / active):
Power consumption at max. load (apparent / active):
Protection:
DC INPUT
Power supply:
Protection:
Terminals for connecting the battery:
Automatic disconnect the battery:
85 - 253 V AC/ 50 - 60 Hz
max. 13 VA/ 2 W
max. 180 VA/ 111 W
- safety fuse T3.15 A inside the unit
- electronic protection (short circuit
current and thermal overload)
OVERLOAD
switching power supply works correctly
output voltage 27V is correct (UOUT>24V)
output voltage 12V is correct
batteries are recharged
UOUT LOW
UOUT OK
+12V OK
CHARGE
UPRI FAIL
switching power supply works correctly
low output voltage 27V (21V<UOUT<24V)
output voltage 12V is correct
batteries are not recharged
OVERLOAD
UOUT LOW
UOUT OK
+12V OK
- DC 24V (two 12V batteries in series)
-safety fuse F6.3 A inside the unit
- electronic protection against current overload
- each battery separately
- separately routed extreme terminals (24)
- for the battery voltage <21 V
- when exceeding discharge current 4.2 A
CHARGE
UPRI FAIL
switching power supply is overload
low output voltage 27V (UOUT<21V)
low output voltage 12V
batteries are not recharged
OVERLOAD
UOUT LOW
UOUT OK
+12V OK
CHARGE
UPRI FAIL
OUTPUTS
Output voltage 1:
Max. capacity:
Output voltage 2:
Max. capacity:
The overall efficiency of resources:
Time delay after connecting to the AC network:
Max. charging current:
L E D S I G N A L I Z AT I O N
Output voltage 27 V OK (UOUT > 24 V):
Switch. power supply does not work (does not oscillate):
Low output voltage (21 V < UOUT< 24V):
Output voltage 12 V OK (U > 11 V):
Overloading the power supply (UOUT < 21 V):
Charging the battery (charging current > 50mA):
27.6 V
3.6 A
12.2 V
0.35 A
about 88%
up to 1 s
adjustable from 0.2 to 2.2 A
green LED UOUT OK
flashing red LED UPRI FAIL
yellow LED UOUT LOW
green LED + 12 V OK
red LED OVERLOAD
yellow LED CHARGE
switching power supply works correctly
output voltage 27V is correct (UOUT>24V)
low output voltage 12V (short-circuit, overload)
batteries are recharged
OVERLOAD
UOUT LOW
UOUT OK
+12V OK
CHARGE
UPRI FAIL
switching power supply works correctly
output voltage 27V is correct (UOUT>24V)
output voltage 12V is correct
power supply is overload
batteries are not recharged
OVERLOAD
UOUT LOW
UOUT OK
+12V OK
CHARGE
UPRI FAIL
switching power supply not working correctly UPS mode
output voltage 27V is correct (UOUT>24V)
output voltage 12V is correct
batteries are not recharged
OVERLOAD
UOUT LOW
UOUT OK
+12V OK
CHARGE
O U T P U T S TAT U S
STATUS output 1 (UPRI OK):
STATUS output 2 (UOUT OK):
Output type:
Max. connectable voltage:
Max. current output:
Voltage drop on the switch max:
UPRI FAIL
closed, when power supply works (not blinking LED UPRIFAIL)
closed, if UOUT > 21V (not lit red LED OVERLOAD)
open collector current limited
50 V DC
50 mA
at 10 mA ... 140 mV
at 30 mA ... 400 mV
at 50 mA ... 700 mV
switching power supply not working correctly UPS mode
low output voltage 27V (21V<UOUT<24V)
output voltage 12V is correct
batteries are not recharged
OVERLOAD
UOUT LOW
UOUT OK
+12V OK
CHARGE
UPRI FAIL
O T H E R DATA
Electric strength AC input - output:
The connection terminals:
Cable size (mm2):
Operating temperature:
Storage Temperature:
Working humidity:
Cover:
Overvoltage category:
Degree of pollution:
Working position:
Installation:
Execution:
Dimensions:
Weight:
Related standards:
4 kV
row
max. 1 x 2.5, max. 2 x 1.5 (with sleeve max. 1 x 1.5)
-20 °C to +55 °C
-30 °C to +70 °C
20 to 90 % RH
IP40 front panel, IP20 terminals
III.
2
arbitrary, vertical is optimum
on the DIN rail EN60715
6-MODULE
90 x 105 x 65 mm
392 g
General: EN61204
Safety: EN61204-7
EMC: EN61204-3
17
External master bus CIB MI3-02M
External master MI3-02M provides expansion of the amount of units iNELS3 connected to the
central unit CU3-01M or CU3-02M for 2 times 32 units.
If you require the use of a central unit CU3-01 (02M) in combination with the iNELS2 units ,
all the units must be connected to the bus CIB lines, which are based on an external master
MI3-02M/iNELS2.
Up to 8 modules MI3-02M or MI3-02M/iNELS2 can connect to a central unit via the system
bus EBM.
In conjunction with the central unit CU3-01M(02M), it can achieve a maximum capacity of the
bus iNELS of up to 576 units.
MI3-02M and MI3-02M/iNELS2 have marked on the front panel of the unique hardware
address. This address belongs to the line CIB1. IDM software then automatically sets the
hardware address of the BUS line CIB2 (this address is always one value higher).
MI3 units are supplied from PS3-100/iNELS.
To power the lines CIB, it is necessary to use a BUS separator BPS3-02M or BPS3-01M (supply
only one line). In case of using MI3-02M/iNELS2 is used BPS2-02M or BPS2-01M.
EAN code
MI3-02M 8595188132411
MI3-02M/iNELS2 8595188150637
Status signaling of each bus (operation, fault) is indicated by two-color LEDs on the front
panel of the module.
The last MI2-02M connected to the EBM bus must be closed with a 120 Ω termination resistor.
This part adapted to be inserted between terminals is included into central units packages
and it is necessary to insert between terminals EBM+ and EBM-.
T E C H N I C A L PA R A M E T E R S
OUTPUTS
Number of connected units:
MI3-02M, MI3-02M/iNELS2 in 1-MODULE version is designed for mounting into a switchboard,
on DIN rail EN60715.
max. 64 (2x32)
Example of connection
C O M M U N I C AT I O N
Installation BUS:
Data BUS:
Unit status indication:
Bus fault indication:
Length of BUS CIB wire:
Length of BUS EBM wire:
2 x CIB
EBM
green LED
red LED
max. 2x550 m
max. 500 m
EBM EBM +
EBM+ EBM- GND
P O W E R S U P P LY
Supply voltage:
Ideal supply voltage:
Rated current:
22-30 V DC
27 V DC
25 mA (at 27V DC)
7
BPS3-02M
O P E R AT I N G C O N D I T I O N S
Operating temperature:
-20 to +55 °C
Storage temperature:
-25 to +70 °C
Humidity:
max. 80 %
Protection degree:
IP20 device, IP40 mounting in the switchboard
Overvoltage category:
II.
Pollution degree:
2
Operating position:
any
Installation:
in a switchboard on DIN rail EN 60715
Design:
1-MODULE
Terminal:
max. 2.5 mm2
7
from PS3-100/iNELS
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
18
90 x 18 x 65 mm
80 g
MI3-02M
+ 27V
GND
+
CIB1
+
- CIB2
Bus separator from power supply BPS3-01M, BPS3-02M
BPS3-01M
BPS3-02M
Units BPS3-01M and BPS3-02M serve for impedance separation of CIB from supply
voltage power.
Bus separator BPS3 or BPS3-01M-02M is required for each type CU3 central unit and
external master MI3-02M.
BPS3-01M allows you to connect one bus CIB.
BPS3-02M allows you to connect two separate CIB1 and CIB2.
Outputs are equipped with overcurrent and overvoltage protection.
Indication of output voltage outputs CIB LED.
BPS3-01M and BPS3-02M in 1-MODULE version is designed for mounting into a
switchboard, on DIN rail EN60715.
EAN code
EAN code
Example of connection
BPS3-02M 859518813243
8595188132435
BPS3-01M 8595188132442
132442
BPS3-01M
CIB+
CIB-
TECHNICAL PARAMETERS
OUTPUTS
Voltage CIB:
Maximum capacity:
C O M M U N I C AT I O N
Installation BUS:
BPS3-01M
22-30 V DC
3A
BPS3-02M
2 x 22-30 V DC
2 x 1A
1x CIB
BPS3-01M
2 x CIB
CIB
P O W E R S U P P LY
Supply voltage:
Rated current:
Status indication voltage on terminals:
CONNECTION
Terminals:
22-30 V DC
max. 8 mA
1 x green LED
max. 15 mA
2 x green LED
max. 2.5 mm2/1.5 mm2 with sleeve
O P E R AT I N G C O N D I T I O N S
Operating temperature:
-20 to +55 °C
Storage temperature:
-30 to +70 °C
Protection degree:
IP20 device, IP40 mouting in to the switchboard
Overvoltage category:
Pollution degree:
Operating position:
Installation:
Design:
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
7
GND input supply voltage
+ 27V of PS3-100/iNELS
II.
2
any
in a switchboard on DIN rail EN 60715
1-MODULE
90x17.5x64 mm
46 g
BPS3-02M
CIB1+
CIB2+
CIB1-
CIB2-
53 g
BPS3-02M
7
GND input supply voltage
+ 27V of PS3-100/iNELS
19
GSM communicator GSM3-01M
It serves for communication with the iNELS system via commands sent in short SMS messages
from mobile phone GSM.
Via GSM3-01M aned mobile phone, you can control the system, and the system can inform
you back by sms or ringing.
Max. capacity of GSM3-01M is 32 phone numbers, 48 outgoing and 32 incoming SMS
messages. Max. length of SMS is 20 symbols.
GSM3-01M IDM can through software-defined numbers to dial, ring 20 s and disconnected. It
can also perform actions on incoming calls.
GSM3-01M can also serve as a transmitter of SMS messages or in case of intrusion or alert to
a security agency.
Operating range is 850, 900 as well as 1800, 1900 MHz (quad-band).
SIM card is inserted into the unit from the front panel.
Connector Mini USB for service purposes.
GSM3-01M is connected to the central unit CU3-01M (02M) via the system bus EBM.
EAN code
GSM3-01M 8595188132428
External antenna AN-E 859415759012
In case it involves the last unit on the system bus EBM, it is necessary to terminate the wire
with a resistor with rated resistance of 120Ω. This part adapted to be inserted between
terminals is included into central units packages and it is necessary to insert between
terminals EBM+ and EBM-.
The package includes is an external magnetic antenna (cable 3m, 5db gain), which is
connected to the connector RSMA (F) on the front panel.
TECHNICAL PARAMETERS
GSM3-01M in 3-MODULE version is designed for mounting into a switchboard, on DIN rail
EN60715.
Example of connection
C O M M U N I C A T I O N
system bus EBM
850/900/1800/1900 MHz
2W for GSM 900, 1W for GSM 1800
max. 80 (48+32)
max. 32
red LED
Communication interface:
GSM network ( Quad-band) :
Transmitter output power:
Number of informative SMS:
Number of stored numbers:
Transmission indication:
+
3
C O N N E C T I O N
Terminals:
O P E R A T I N G
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operation position :
Installation:
Design:
D I M E N S I O N S
Dimensions:
Weight:
20
2
2
max. 2.5 mm /1.5 mm with sleeve
C O N D I T I O N S
-20 to +55 °C
-30 to +70 °C
20 IP devices, 40 IP with cover in switchboard
II.
2
any
to DIN rail EN 60715
3-MODULE
A N D W E I G H T
90 x 52 x 65 mm
128 g
+
-
27 V DC/250 mA
green LED
EBM
S U P P L Y
Supply voltage/rated current:
Suppy voltage indication:
EBM
P O W E R
EBM
EBM
GND
+27V
Notes
21
Switching actuator, 2-channel SA3-02M
Actuator SA3-02M is designed for switching two various appliance and loads with potentialless
contact.
SA3-02M is a switching actuator containing 2 independent relays with changeover
potentialless contacts.
Maximum load per contact is 16 A/4000 VA/AC1.
Each of the two output contacts are individually controllable and addressable.
Both relays are individually decorated input terminals, and therefore can switch various
independent potentials.
The actuator is designed for switching up to two various appliances and loads relay output
(potentialless contact).
Thanks to changeover contacts, it can be used to control one 230V power (such as blinds,
shutters or awnings) with appropriate bridging, the contacts can secure hardware blocking
the possibility of simultaneous switching of the phase on both outputs.
LEDs on the front panel signal the status of each output.
EAN code
Contact status of each relay can be changed separately and manually by control buttons on
the front panel.
SA3-02M 8595188132374
Switching actuators SA3 are normally supplied in the option AgSnO2 contact material, they can
be supplied with contact AgNi by request.
SA3-02M in 1-MODULE version is designed for mounting into a switchboard, on DIN rail
EN60715.
TECHNICAL PARAMETERS
OUTPUTS
Output:
Switching voltage:
Switching load:
Surge current:
Insulation voltage between
outputs and built-in circuits:
Insulation voltage between
output relays RE1 and RE2:
Minimal switching current:
Switching frequency/no load:
Switching frequency/rated load:
Mechanical lifetime:
Electrical lifetime AC1:
Outputs indication:
Example of connection
CIB +
CIB -
2x switching 16 A/AC1
250 V AC1, 24 V DC
4000 VA/AC1, 384 W/DC
30 A/<3s
3.75 kV, SELV dle EN 60950
SA3-02M
1000 V AC
100 mA
1200 min-1
6 min-1
3 x 107
0.7 x 105
2x yellow LED
C O M M U N I C AT I O N
Installation BUS:
25 2 6 28
CIB
15 1 6 18
P O W E R S U P P LY
Supply voltage/rated current:
Status indication unit:
27 V DC/50 mA, from CIB BUS
green LED RUN
AC 230V
L
N
CONNECTION
Terminal:
1
15
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Control device purpose:
Control device constuction:
Automatic operation characteristic:
Heat and fire resistance category:
Anti-shock category (immunity):
Rated impulse voltage:
Overvoltage category:
Pollution degree:
Operation position:
Installation:
Design:
22
18
16
-20 to +55 °C
-30 to +70 °C
IP 20 device, IP 40 mounting in the switchboard
operative control device
individual control device
1.B.E
FR-0
class 2
2.5 kV
II.
2
any
switchboard on DIN rail EN 60715
1-MODUL
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
2
max. 2.5 mm2/1.5 mm2 with sleeve
90 x 18 x 65 mm
82 g
25
28
26
Switching actuator, 4-channel SA3-04M
It serves for switching of various appliances and loads with potentialless contact.
SA3-04M is a switching actuator containing 4 independent relays with changeover
potentialless contacts.
Maximum load per contact is 16 A/4000 VA/AC1.
Each of the four output contacts are individually controllable and addressable.
All four relays are individually decorated input terminals, and therefore can switch
various independent potentials.
The actuator is designed for switching to four various appliances and loads relay output
(potential free contact).
Thanks to changeover contacts, it can be used to control up to two drives 230V power
(such as blinds, shutters or awnings) with appropriate bridging, the contacts can secure
hardware blocking the possibility of simultaneous switching of the phase on both
outputs.
LEDs on the front panel signal the status of each output.
Contact status of each relay can be changed separately and manually by control
buttons on a front panel.
EAN code
SA3-04M 8595188132381
Switching actuators SA3 is normally supplied in the option AgSnO2 contact material, it
can be supplied with contact AgNi by request.
SA3-04M in 3-MODULE version is designed for mounting into a switchboard, on DIN
rail EN60715.
TECHNICAL PARAMETERS
Example of connection:
OUTPUTS
Output:
Switching voltage:
Switching output:
Surge current:
Insulation voltage between
outputs and internal circuits:
Insulation voltage between individual
relay outputs RE1 to RE4:
Min. switched current:
Switching frequency /no load:
Switching frequency/rated load:
Mechanical life:
Electrical life AC1:
CIB +
CIB -
4 x switching 16 A/AC1
250 V AC1, 24 V DC
4000 VA/AC1, 384 W/DC
30 A/<3s
3.75 kV, SELV by EN 60950
Output indication:
1000 V AC
100 mA
1200 min-1
6 min-1
3 x 107
0.7 x 105
4x yellow LED
C O M M U N I C AT I O N
Installation BUS:
CIB
SA3-04M
P O W E R S U P P LY
Supply voltage/rated current:
Status indication unit:
27 V DC/70 mA, from CIB BUS
green LED RUN
CONNECTION
Terminal:
max. 2.5 mm2/1.5 mm2 with sleeve
AC 230V
L
N
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Control device purpose:
Control device constuction:
Automatic operation characteristic:
Heat and fi re resistance category:
Anti-shock category (immunity):
Rated impulse voltage:
Overvoltage category:
Pollution degree:
Operation position:
Installation:
Design:
-20 to +55 °C
-30 to +70 °C
IP 20 device, IP 40 mounting in the switchboard
operative control device
individual control device
1.B.E
FR-0
class 2
2.5 kV
II.
2
any
switchboard on DIN rail EN 60715
3-MODULE
1
15
2
18
16
25
3
28
26
35
4
38
36
45
48
46
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
90 x 52 x 65 mm
161 g
23
Switching actuator 6-channel SA3-06M
The actuator is designed for switching up to six various appliances and loads with potentialless
contact.
SA3-06M is a switching actuator contains 6 independent relays with changeover potentialless
contacts.
Maximum load per contact is 8 A/2000 VA/AC1.
Each of six output contacts are individually controllable and addressable.
The relays are divided into two groups, the group of four relays on the bottom terminal
switches the common potential, a pair of relays on top of the terminal switches second
common potential.
All relays are equipped with changeover contacts, but given the common supply terminals,
four or a pair of relay, hardware does not block the ability of the current phase switching on
both outputs controlling the drive 230 V (blinds, shutters). But the actuator can control these
drives used on the prepared software blocking in IDM.
The actuator is suitable for operating discontinuously controlled thermo drives in the
distributor underfloor heating.
LEDs on the front panel signal the status of each output.
EAN code
SA3-06M 8595188132879
Contact status of each relay can be changed separately and manually by control buttons on
a front panel.
TECHNICAL PARAMETERS
SA3 is normally supplied in the option AgSnO2 contact material, it can be supplied with contact
AgNi by request.
SA3-06M in 3-MODULE version is designed for mounting into a switchboard/DIN rail EN60715.
Example of connection
OUTPUTS
Output:
Switching voltage:
Switching output:
Surge current:
Insulation voltage between
outputs and internal circuits:
Insulation voltage between individual
relay outputs RE1-RE4; RE5-RE6:
Min. switched current:
Switching frequency /no load:
Switching frequency/rated load:
Mechanical life:
Electrical life AC1:
Output indication:
6 x switching 8 A/AC1
250 V AC1, 24 V DC
2000 VA/AC1, 192 W/DC
20 A/<3s
CIB +
CIB -
3.75 kV, SELV by EN 60950
1000 V AC
10 mA/ 10V
300 min-1
15 min-1
1 x 107
1 x 105
6x yellow LED
58
56
68
66
C O M M U N I C AT I O N
Installation BUS:
CIB
P O W E R S U P P LY
Supply voltage/rated current:
Status indication unit:
27 V DC/60 mA, from CIB BUS
green LED RUN
CONNECTION
Terminal:
max. 2.5 mm2/1.5 mm2 with sleeve
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Control device purpose:
Control device constuction:
Automatic operation characteristic:
Heat and fi re resistance category:
Anti-shock category (immunity):
Rated impulse voltage:
Overvoltage category:
Pollution degree:
Operation position:
Installation:
Design:
-20 to +55 °C
-30 to +70 °C
IP20 device, IP40 mounting in the switchboard
operative control device
individual control device
1.B.E
FR-0
class 2
2.5 kV
II.
2
any
switchboard on DIN rail EN 60715
3-MODULE
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
24
90 x 52 x 65 mm
256 g
L
N
AC 230V
1
2
3
28
38
48
16
26
36
46
COM 1
5
COM 2
4
18
6
58
68
56
66
Switching actuator, 12-channel SA3-012M
The actuator is designed for switching to twelve various appliances and loads with
potentialless contact.
SA3-12M is a switching actuator containing 12 independent relays with NO potentialless
contacts, with the fact that each quaternion relay switches the same potential.
Maximal loadability of contacts is 8 A/2000 VA/AC1.
Each of the twelve output contacts are individually controllable and addressable.
Actuator is powered by an AC voltage 230V.
CIB is galvanically separated from the internal circuits of unit.
LED on front panel signalizes state of each output.
Contact status of each relay can be changed separately and manually by control buttons
on a front panel.
SA3-012Mis normally supplied in the option AgSnO2 contact material, the order can be
supplied with contact AgNi by request.
EAN code
SA3-012M 8595188132466
466
SA3-012M in design 6-MODULE is designed to be mounted into a switchboard, onto
DIN rail EN60715.
TECHNICAL PARAMETERS
Example of connection
OUTPUTS
Output:
Switched voltage:
Switched output:
Peak current:
Insulation voltage between relay
outputs and internal circuits:
Insulationg voltage between
individual relay outputs RE1-RE4;
RE5-RE8; RE9-RE12:
Max. current by common terminal:
Minimal switched current:
Switching frequency without load:
Switching frequency with rated load:
Mechanical life:
Electrical life AC1:
Output indication:
12 x NO 8 A/AC1
250 V AC1, 30 V DC
2000 VA/AC1, 240 W/DC
20 A/<3s
CIB +
CIB -
3.75 kV, SELV by EN 60950
AC 230 V
L
N
COM3
1000 V AC
16 A
10 mA / 10 V
300 min-1
15 min-1
1 x 107
1 x 105
12 x yellow LED
SA3 - 012M
CIB
green LED RUN
P O W E R S U P P LY
Supply voltage/rated current:
230V AC/20 mA
CONNECTION
Terminal:
max. 2.5 mm2/1.5 mm2 with sleeve
COM1
1
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Control device purpose:
Control device constuction:
Automatic operation characteristic:
Heat and fi re resistance category:
Anti-shock category (immunity):
Rated impulse voltage:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
Design:
COM2
C O M M U N I C AT I O N
Installation BUS:
Status indication unit:
-20 to +55 °C
-30 to +70 °C
IP 20 device, IP 40 mounting in the switchboard
operative control device
individual control device
1.B.E
FR-0
class 2
2.5 kV
II.
2
any
switchboard on DIN rail EN 60715
6-MODULE
5
18
COM1
2
9
58
COM2
6
28
3
10
68
7
38
4
108
11
78
8
48
98
COM3
118
12
88
128
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
90 x 105 x 65 mm
460 g
25
Switching actuators SA3-01B, SA3-02B
SA3-01B
Actuators are designed for switching of one (SA3-01B), respectively two (SA3-02B) of
various appliances and loads relay output (potentialless contact).
SA3-02B
SA3-01B contains 1 relay with switching potentialless contact with max. load 16A/4000 VA/AC1.
SA3-02B contains 2 relays with switching potentialless contacts with max. load 8A/2000 VA/AC1.
Output contacts are separately controllable and addressable.
Both relay actuator SA3-02B are individually decorated input terminals, and therefore
can switch various independent potentials.
Thanks to changeover contacts, the SA3-02B actuator can used to control a 230V drive
(such as blinds, shutters or awnings), whereas by proper bridging of contacts, it is
possible to secure locking hardware options while switching on phase two outputs.
Actuators are equipped with a temperature input for connecting an external two-wire
temperature sensor TC / TZ (see accessories).
LED on front panel signalizes state of each output.
EAN code
EAN code
SA3-02B 8595188132367
SA3-01B 8595188132350
SA3 is normally supplied in the option AgSnO2 contact material. It can be
supplied with contact AgNi by request.
SA3-01B, SA3-02B are designed for mounting into the installation box
Example of connection SA3-01B
TECHNICAL PARAMETERS
INPUTS
Temperature measuring:
Scope and accuracy of tem. meas.:
SA3-01B
SA3-02B
Yes, input for external thermo sensor TC, TZ
-20 to +100°C; 0.5°C from the range
CIB +
CIB temperature sensor TC/TZ
OUTPUTS
Output:
Switching voltage:
Switched load:
Surge current:
Insulation voltage between
outputs and built-in circuits:
Insulation voltage between
relay outputs RE1-RE2:
Minimal switching current:
Switching frequency/no load:
Switching frequency/rated load:
Mechanical lifetime:
Electrical lifetime for AC1:
Output indication:
1x NO 16 A/AC1
2 x NC 8 A/AC1
250 V AC1, 24 V DC
4000 VA/AC1, 384 W/DC 2000 VA/AC1, 192 W/DC
30 A/<3s
SA3-01B
3.75 kV, SELV by EN 60950
16A /4000VA
250Vµ AC1
x
100 mA
1200 min-1
6 min-1
3 x 107
0.7 x 105
yellow LED
1000 V AC
100 mA/10 V
300 min-1
15 min-1
1 x 107
1 x 105
2x yellow LED
C O M M U N I C AT I O N
CIB
Installation BUS:
AC 230 V
L
N
P O W E R S U P P LY
Supply voltage/rated current:
Status indication unit:
Example of connection SA3-02B
27 V DC/30 mA
27 V DC/50 mA
green LED RUN
CIB +
CIB -
CONNECTION
Data terminals:
Power outputs:
temperature sensor TC/TZ
terminal, 0.5 - 1 mm2
2x conduct. CY, Ø 2.5 mm2
6x conduct. CY, Ø 0.75 mm2
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storage temperature:
Protection degree:
Control device purpose:
Control device construction:
Characteristics of automatic operation:
Heat and fi re resistance category:
Anti-shock category (immunity):
Rated impulse voltage:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
-20 to +55 °C
-30 to +70 °C
IP 30
operative control device
individual control device
1.B.E
FR-0
class 2
2.5 kV
II.
2
any
into installation box
SA3-02B
8A /2000VA
250Vµ AC1
AC 230 V
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
26
49 x 49 x 21 mm
43 g
45 g
L
N
Shutter actuator JA3-02B/DC
JA3-02B/DC actuator serves to control blinds, shutters, garage doors, entrance gates, etc.
Operates electrical motors, which are controlled in 2 directions and have a built-in
limit switch.
JA3-02B/DC controlled electric drives with supply voltages up to 24 V DC, where the
direction of rotation of the driver is controlled by changing the voltage polarity of the
motor.
The unit is equipped with thermal and overcurrent overload protection outputs.
Status of units is indicated by green LED RUN on the front panel:
- with the supply voltage connected (through CIB) and the unit is not controlled by bus
CIB, LED RUN shines.
- with the supply voltage connected (through CIB) and the unit is controlled by bus CIB,
LED RUN flashes.
Status of output contacts UP/DOWN (
):
- while contact UP ( ) is switched, red LED shines (orange).
- while contact DOWN ( ) is switched, green LED shines.
EAN code
JA3-02B/DC 8595188132718
Input for thermo sensor TC/TZ (more information about sensors - see accessories).
TECHNICAL PARAMETERS
JA3-02B/DC is designed for mounting into an installation box.
INPUT
Thermo input for temperature
input for external thermo sensor
TC, TZ; see accessories
measuring:
Range and accuracy of thermomeasuring: -20 to +100°C / 0.5°C from the range
Example of connection
OUTPUTS
Insulative voltage between outputs
and internal circuits:
Rated current:
Peak current:
Switched voltage:
Output indication UP, ( ) :
Output indication DOWN, ( ) :
3.75 kV, SELV by EN 60950
0.85A*
1.5 A / < 3s
12 - 24 V DC
red (orange) LED
green LED
CIB +
CIB temperature sensor TC/TZ
JA3-02B/DC
C O M M U N I C AT I O N
Installation BUS:
CIB
P O W E R S U P P LY
Supply voltage/rated current:
Status indication unit:
27 V DC/60mA, from CIB BUS
green LED RUN
supply voltage
motors
CONNECTION
Data terminals:
Power outputs:
terminal 0.5 - 1 mm2
4 x conductor CY
0.75 mm2
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storage temperature:
Protection degree:
Control device purpose:
Control device construction:
Characteristics of automatic operation:
Heat and fi re resistance category:
Anti-shock category (immunity):
Rated impulse voltage:
Overvoltage category:
Pollution degree:
Operation position:
Installation:
-20 to+50°C
-30 to+70°C
IP30
operative control device
individual control device
1.B.E
FR-0
class 2
2.5 kV
II.
2
any
into an installation box
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
49 x 49 x 13 mm
32 g
M
* Maximal operation time of outputs with rated current 0.85A is 10 minutes…after
that the output heating protection activates. The lower the current, the longer
duration of protection.
27
Universal dimming actuator, 2-channel DA3-22M
DA3-22M is a universal dimming two-channel actuator used to control light intensity
of dimmable energy saving lamps (ESL), LED bulbs and R, L, C with power suppl 230 V
AC, but you can also use the actuator for switching appliances.
DA3-22M integrates 2 binary inputs, which allow 230V AC voltage connection (normal
wall switch contacts) These inputs are in taken in the software IDM as standard binary
inputs.
DA3-22M has two MOSFET controlled outputs 230V AC, maximum load is 2x 400 VA.
Type of light source is set by a switch on the front panel.
By setting the min. brightness potentiometer on the front panel, flashing is eliminated
of different types of light sources.
Buttons on the front panel, you can manually switch on or off the corresponding
output.
Electronic overcurrent and thermal protection - switch off output in case of overload
short circuit and overheating.
EAN code
DA3-22M 8595188132626
During installation, it is necessary to leave on each side of the actuator at least half the
module space for better cooling.
DA3-22M in 3-MODULE version is designed for mounting into a switchboard on DIN
rail EN60715.
TECHNICAL PARAMETERS
INPUTS
Input:
Temperature measuring:
Scope and accuracy of temp. measurement:
Number of control buttons:
Example of connection
2x inputs, switching potential L
YES, input for external thermo sensor TC/TZ
+15 to +35°C; 0.3°C from the range
2x buttons,
4x potenciometers on front panel
CIB +
CIB -
OUTPUTS
Output:
Load type:
Galvanic separation:
Insulation voltage between outputs
and built-in circuits:
Isolation voltage between particular
power:
Minimal controlled load:
Maximal controlled load:
Output indication ON/OFF:
Device protection:
temperature sensor TC / TZ
2 contactless outputs, 2x MOSFET
resistive, inductive, capacitive*, LED, ESL
YES
3.75 kV, SELV according to EN 60950
DA3-22M
max. 500 V AC
10 VA
400 VA for each channel
2x yellow LED
- thermal
- short-term overload
- long-term overload
C O M M U N I C AT I O N
Installation BUS:
CIB
P O W E R S U P P LY
Supply voltage/rated current:
Status indication unit:
27 V DC/10 mA, from CIB BUS
green LED RUN
F 5A
AC 230 V L
N
CONNECTION
Terminal:
2
2
max. 2.5 mm /1.5 mm with sleeve
Types of connectable loads:
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Heat and fi re resistance category:
Anti-shock category (immunity):
Rated impulse voltage:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
Design:
-20 to +35 °C
-30 to +70 °C
IP 20 device, IP 40 mounting in the switchboard
FR-0
class 2
2.5 kV
II.
2
vertical
switchboard on DIN rail EN 60715
3-MODULE
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
90 x 52 x 65 mm
136 g
*Attention: It is not allowed to connect loads of inductive and capacitive character,
at the same time.
28
type of source
R
resistive
L
inductive
C
capacitive
symbol
description
ordinary light bulb, halogen lamp
coiled transformer for low-voltage halogen lamps
electronic transformer for low-voltage halogen lamps
LED
LED lamps and LED light sources, 230 V
ESL
dimmable energy-saving fluorescent tubes
A list of dimmable light sources can be found here: http://www.elkoep.com/solutions
Dimming 2-channel actuator for fluorescent lamps LBC3-02M
LBC3-02M is a dimming analog two-channel actuator designed for control of dimming
light ballasts with signal 1-10V.
During analog voltage output 1-10V control, relay contact automatically switches power
supply to light ballast (0%=relay OFF, 1-100%=relay ON)
LBC3-02M contains 2 independent analog voltage outputs 1-10V and their dependents
2 relays with potential-free contact.
Maximum contacts load 16 A/4000 VA/AC1.
Each of two-channels is separately controllable and addressable.
LED‘s on front panel signals status of each channel.
With control buttons on the front panel, is possible to change thestatus of each channel
separately.
LBC3-02M in 3-MODULE version is designed for mounting into a switchboard/ DIN rail
EN60715.
EAN code
LBC3-02M 8595188132688
TECHNICAL PARAMETERS
INPUTS
Number of control buttons:
OUTPUTS
Output:
Switching voltage:
Switching capacity:
Peak current:
Insulation voltage between
outputs and internal circuits:
Insulation voltage between
relay outputs RE1 and RE2:
Minimal switched current:
Frequency of switching/no load:
Frequency of switching/rat. load:
Mechanical life:
Electrical life AC1:
Output indication:
2 buttons on the front panel
2x 1-10V/10 mA
2x changeover 16 A/AC1
250 V AC1, 24 V DC
4000 VA/AC1, 384 W/DC
30 A/<3s
Example of connection
CIB +
CIB DIML light ballast
3.75 kV, SELV by EN 60950
7
DC 1 - 10 V
1000 V AC
100 mA
-1
1200 min
-1
6 min
7
3 x 10
5
0.7 x 10
2x yellow LED
4
220 V - 240 V
DC 1 - 10 V
2
4
3
2
220 V - 240 V
CIB
P O W E R S U P P LY
Supply voltage/rated current:
Status indication unit:
3
1
C O M M U N I C AT I O N
Installation BUS:
6
5
1
light source
corresponding
fluorescent
27 V DC/60 mA, from CIB BUS
green LED RUN
L
N
PE
AC 230 V
CONNECTION
Terminal:
max. 2.5 mm2/1.5 mm2 with sleeve
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Purpose of control devices:
Control device design:
Characteristics machine. action:
Category of resistance to heat and fire:
Category (immunity):
Rated impulse voltage:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
Design:
-20 to +55 °C
-30 to +70 °C
IP20 device, IP40 mounting in the switchboard
operative control devices
independent control device
1.B.E
FR-0
class 2
2.5 kV
II.
2
any
switchboard on DIN rail EN 60715
3-MODUL
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
90 x 52 x 65 mm
129 g
29
Converter iNELS - DALI/DMX EMDC-64M
Unit EMDC-64M is designed to control electronic ballasts DALI and DMX receivers from
the iNELS.
EMDC-64M allows you to control up to 64 independent electronic ballasts DALI (Digital
Addressable Lighting Interface) for fluorescent , LED and other lamps.
EMDC-64M allows the connection of up to 32 receivers DMX (Digital Multiplex) in one
segment. When using repeaters, it can control up to 64 devices.
Control is possible from the iNELS BUS System via the system bus EBM or from the RF
Control wireless transmitters. Selection of control (RF/EBM ) and controlled (DALI/DMX)
interface is done via DIP switches on the front panel of the unit.
When used in the context of bus wiring (interface EBM) it is set using the IDM software.
Unit EMDC - 64M is powered by 230 V AC.
DALI bus is powered directly through the unit EMDC - 64M.
In the event that this is the last unit on the system bus EBM, it is necessary to use a
termination resistor having a nominal resistance value of 120Ω .
EAN code
EMDC-64M 8595188150309
External antenna AN-E: 859415759012
Internal antenna AN-I: 8595188161862
DMX bus must be terminated at its end resistor with a nominal resistance value of
120Ω. Bus termination DMX -side EMDC - 64M is already implemented inside the unit.
Two members of the nominal resistance value of 120Ω adapted for easy insertion to the
terminals come with the package. To end the system bus EBM, a member is inserted
between the terminals EBM+ and EBM- on last unit on the bus. To end DMX bus termination
is performed on the terminals of the last receiver (slave unit) e.g. DCDA-33M/RGB.
TECHNICAL PARAMETERS
P O W E R
PRG button and MINI USB connector on the front panel are used to set up
communication with the transmitter RF Control.
S U P P L Y
Supply voltage:
230 V AC
EMDC-64M in 3 module is designed for panel mounting on DIN rail EN60715.
C O M M U N I C A T I O N
Input interface:
EBM bus (RS485 communication)
iNELS RF Control
DALI (max. 64 ballasts)
DMX (max. 32 receivers, with repeator to 64)
Output interface:
I N D I C A T I O N
Power supply:
Error:
Communication:
O P E R A T I N G
green LED RUN
red LED ERR
bicolour LED DALI/DMX
C O N D I T I O N S
Operating temperature:
Storage temperature:
Protection degree:
Control device purpose:
Control device construction:
Characteristic of automatic action:
Heat and fire resistance category:
Anti-shock category (immunity):
Rated impulse voltage:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
Implementation:
D I M E N S I O N
Dimension:
Weight:
R F
C O N T R O L
Communication protocol:
Transmitting frequency:
Signal transmission method:
Output for RF antenna:
RF Antenna:
Range in free space:
-20°C to +55°C
-30°C to +70°C
IP20 device, IP40 mounitg in the switchboard
operating control device
individual control device
1.B.E
FR-0
class 2
2.5 kV
II.
2
any
into switchboard on DIN rail EN60715
3-modulle
A N D
Example of connection
L
N
EBM EBM +
EMDC-64M
ERR
W E I G H T
N
90 x 52 x 65 mm
130g
I N T E R F A C E
Oasis & RF Touch Compatible
868 MHz
bidirectionally addressed message
SMA connector
1 dB (supplied)
up to 100m
120 Ω
DALI 64
30
EBM
DALI 1
DMX 1
DMX 32
Dimming actuator DCDA-33M/RGB
DCDA-33M/RGB dimming actuator is designed for dimming RGB and LED light sources
with power supply 12-24 V DC, which are controlled by variable current.
The actuator has three independent channels and each output channel is individually
addressable and controllable.
If desired, the channels can be associated as a single actuator for actuating the RGB
source.
DCDA-33M/RGB actuator can be controlled from the bus DALI, DMX or CIB .
DCDA-33M/RGB can directly control from the system iNELS where the communication
interface is the installation CIB.
If ithe communication interface DALI or DMX is used, the DALI master EMDC-64M can
be used.
Setting the communication interface and addresses of actuators is performed using DIP
switches:
a) switch No. 1
- In the upper position determines DALI or CIB
- In the lower position determines DMX
b ) switch No. 2 (if that switch 1 is in the upper position)
- In the upper position determines DALI
- In the lower position determines CIB
EAN code
DCDA-33M/RGB 8595188146807
Using the control buttons on the front panel, you can manually control the output.
The input circuits of communication interfaces are optically isolated from the supply
voltage connected lamp unit, and is therefore resistant to electromagnetic interference.
DCDA-33M/RGB in 3-module is designed for panel mounting on DIN rail EN60715.
TECHNICAL PARAMETERS
P O W E R
S U P P L Y
Supply terminals:
Un+, GND
Supply voltage:
12-24V DC stabilized
Consuption:
min. 0.8W max. 48W
Supply voltage tolerance:
+10 / -10%
O U T P U T S
Dimming load:
LED 12-24V DC with common cathode /
Example of connection
DMX bus
A
B
GND
120 Ω
DALI bus
CIBCIB+
RGB LED 12-24V DC with common cathode
Number of channels:
3
Rated current:
0 - 2A
Output power:
3 x 40W
Output voltage:
0 - 50V
Switching voltage:
Un
C O N T R O L
DALI:
1200bit/s, 250 mA
CIB:
compatible with iNELS3, consumption < 2mA
DMX:
250 kbit/s, 512 CH
O P E R A T I N G
C O N D I T I O N S
Operating temperature:
-20°C to +55°C
Storage temperature:
-30°C to +70°C
Protection degree:
IP20 device, IP40 mounitg in the switchboard
Overvoltage category:
II.
Pollution degree:
2
Operating position:
any
Installation:
into switchboard on DIN rail EN60715
Implementation:
3-modulle
D I M E N S I O N
A N D
12-24 V DC
GND
W E I G H T
Dimension:
90 x 52 x 65 mm
Weight:
135g
Setting the DIP switches
Setting the DALI communication interface - Switch 1 and 2.
Setting address - Switch 5-10.
Setting the CIB communication interface - Switch 1 and 2.
Address is not settable, is given HW address.
Setting the DMX communication interface - Switch 1.
Setting address - Switch 2-10.
31
Dimming actuator for LED strips RFDA-73M/RGB
Used to dim LEDs, an LED strip and RGB LED strip with power supply 12-24V DC, control
is performed with RF Control wireless transmitters or signal 0-10V/ 1-10V, or iNELS DAC
converter.
The function (FUNC) selection switch enables setting of colored light scenes. Upon
switching off , the set level is stored in the memory, and when switched back on, it
returns to the most recently set value.
The load for individual channels is 3x5A, which in practice enables dimming of approx.
60W = an 8m RGB LED strips.
The supply voltage to the equipment and the LED strip must be the same. If the
RFDA-73M/RGB is supplied by 12V DC, LED strip / source should also be supplied by
12V DC. The same applies for a supply voltage of 24V DC
Programming is performed by the PROG button located on the front panel of the
device supplied with internal antenna SMA (M)
EAN code
RFDA-73M/RGB 8595188146814
External antenna AN-E 859415759012
Internal antenna AN-I 8595188161862
Optional accessories: external antenna AN-E
TECHNICAL PARAMETERS
CONNECTION
OUTPUTS
Dimmed load:
Number of channels:
Rated current:
Peak current:
Switching voltage:
LED strip 12V,24V with common anode;
RGB LED strips 12V, 24V with common anode
3
3x5 A
3x10 A
Un
Output variations
RF RGB
RF COLOR
RF SINGLE
CONTROLLING
RF by command from the transmitter:
Ext. signal:
Ext. signal:
Range in open space:
Load capacity of output +10V:
868 MHz
0-10 V, 1-10V
1-10 V
up to 160 m
10 mA
P O W E R S U P P LY
Supply terminals:
Supply voltage:
Maximum power without load:
W
Un+, GND
12-24 V DC stabilized
0.8 W
RGB strip
Control options
TERM 0(1)-10V DC
max 1x2.5, max 2x1.5/ with sleeve max. 1x2.5
TERM 0-10V DC
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Pollution degree:
Operating position:
Protection:
Installation:
Design:
-20 to + 50 °C
-30 to + 70 °C
2
any
IP20 device, IP40 mounting in the switchboard
01207D
into a switchboard rail to DIN EN 60715
3-MODULE
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
90 x 52 x 65 mm
130 g
External control of iNELS Bus System:
- outputs 0-10 V or 1-10 V
- e.g. DAC3-04B or DAC3-04M.
32
W
Single LED
CONNECTION
Terminal:
W
RF RGB
RF RGB mode for controlling RGB LED strips.
In the RF RGB programming mode, colors are automatically assigned
to individual transmitter buttons.
Note: It is only possible to use this function for RFWB-40/G, RF KEY and
RFIM-40B.
R
B
RFDA-73M/RGB
pic.1
RFDA-73M/RGB
pic.2
R
G
B
12V DC
G
M
LEGEND
Buttons:
R - red
RF RGB
G - green
B - blue
M - master setting of overall scene brightness
RF Pilot
RF KEY
RFWB-40/G
RF COLOR
RF COLOR mode for controling RBG LED strips, where you can
choose the color for individual transmitter buttons. A long press of
the button starts the color search mode. After releasing the button,
the current color is set for the given button.
Note: It is only possible to use this function for RFWB-40/G, RF KEY
and RFIM-40B.
V V V
V
V
V
12V DC
M
LEGEND
Buttons:
RF COLOR
V - free selection of color
V - free selection of color
V - free selection of color
M - master setting of overall scene brightness
RF Pilot
RF KEY
RFWB-40/G
RF WHITE
RF WHITE mode
This works in a mode where it acts like three independent dimmers
for 12-24V. Each channel can be programmed independently of one
another and has its own address.
Dimming functions are identical to the unit RFDA-71B.
RF Pilot
pic.3
RFDA-73M/RGB
RF WHITE
13
2
4
RF KEY
S1
S2
S3
12V DC
RFWB-40/G
TERM 0-10V a TERM 1-10V
MODES TERM 0 -10V AND TERM 1-10V.
Inputs 0 - 10V and 1 -10V serves for controlling iNELS with the help
of DAC3-04M or DAC3-04B. This means it‘s possible to combine and
control LED strips via iNELS.
01207D
EST - 3
DAC3-04B
TERM 1-10V
TERM 0-10V
RFDA-73M/RGB
RF Touch
pic.4.
R
G
B
12V DC
33
Binary input units IM3-20B, IM3-40B, IM3-80B
Binary input units IM3-20B, IM3-40B and IM3-80B are used for connection of 2, 4 or 8
devices with potential-less contacts (switches, buttons, switches of other design, PIR
sensors, fire and gas detectors, etc.)
IM3-20B
Part of the inputs can be used as a balanced for alarm detectors:
IM3-20B – inputs IN1, IN2
IM3-40B – inputs IN1, IN2
IM3-80B – inputs IN1 – IN5
Contacts of external devices connected to the inputs of the unit can be NO or NC Input parameters are configured in the software IDM.
The units generate a supply voltage of 12V DC/75 mA for powering external intrusion
detectors, so they can power PIR detectors, fire and gas detectors.
Active use 12V DC output for powering detectors increases the nominal consumption
of units from CIB (see technical data).
The units can be used for counting pulses of energy meters with pulse output.
The units are equipped with a temperature input for connecting an external two-wire
temperature sensor TC/TZ (see accessories).
EAN code
IM3-20B 8595188132305
IM3-20B, IM3-40B, IM3-80B in case type B are designed for mounting into a wiring box.
TECHNICAL PARAMETERS
INPUTS
IM3-40B
Input IM3-20B:
Input IM3-40B:
Input IM3-80B:
2x NO or NC against GND(-)
IN1, IN2 are balanced inputs
4x NO or NC against GND(-)
IN1, IN2 are balanced inputs
8x NO or NC against GND(-)
IN1 - IN5 are balanced inputs
Yes, input for external thermo sensor TC/TZ
Temperature measuring:
Range /accuracy of thermomeasuring: -20 to +100°C / 0.5°C from the range
OUTPUTS
Output voltage / current:
12 V DC/75 mA, for supplying EZS sensors
C O M M U N I C AT I O N
Installation BUS:
Status indication unit:
EAN code
IM3-40B 8595188132312
IM3-80B
CIB
green LED RUN
P O W E R S U P P LY
27 V DC/20 mA, from CIB BUS
Supply voltage/rated current:
Rated current of IM3-20B and IM3-40B
60 mA
for full load on output 12 V DC:
Rated current of unit for full load
100 mA
on output 12 V DC of IM2-80B:
CONNECTION
Terminal:
INPUTS IM2-20B:
INPUTS IM2-40B:
0.5 - 1 mm2
4x conductors CY, profile 0.75mm2, length 90mm
6x conductors CY, profile 0.75mm2, length 90mm
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
EAN code
IM3-80B 8595188132329
34
-20 to +55 °C
-30 to +70 °C
IP 30
II.
2
any
into installation box
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
49 x 49 x 13 mm
IM3-20B - 30 g, IM3- 40B - 32 g, IM3-80B - 24g
Example of connection IM3-20B
CIB +
CIB for POWER SUPPLY +12 V
external alarm
detectors GND
12 V DC/max. 75 mA
Example of connection IM3-40B
CIB +
for POWER SUPPLY CIB
+12
V
external alarm
GND
detectors
12 V DC/max. 75 mA
temperature sensor
TC/TZ
temperature sensor
TC/TZ
IM3-40B
IM3-20B
Example of connection IM3-80B
CIB +
CIB for POWER SUPPLY +12 V
external alarm
detectors GND
12 V DC/max. 75 mA
temperature sensor
TC/TZ
IM3-80B
Balanced input
Simple:
Double:
ALARM
2k2
ALARM
TAMPER
1k1
1k1
TAMPER
INx
INx
GND
GND
35
Binary input unit IM3-140M
Binary input unit IM3-140M is designed to connect up to 14 devices with potentialless
contact (such as switches, buttons of other designs, fire and glass detectors and others).
Inputs IN1 - IN7 can be balanced.
Contacts of external devices connected to the inputs of the drive can be NO or NC Input parameters are configured in the software IDM.
The unit generates a supply voltage of 12V DC/150 mA for powering external detectors,
so it can power PIR detectors, fire and gas detectors.
Active use 12V DC output for powering detectors increases the nominal consumption
units from CIB (see technical data).
The unit can be used for counting pulses of energy meters with pulse output.
IM3-140M in 3 module is designed for switchboard mounting on DIN rail EN60715.
EAN code
IM3-140M 8595188132459
Example of connection
TECHNICAL PARAMETERS
INPUTS
Input:
14x NO or NC against GND (-)
IN1 - IN7 -are balanced inputs
CIB +
CIB for POWER SUPPLY +12 V
external alarm
detectors GND
12 V DC / 150 mA
OUTPUTS
Output (power supply 12V for sensors): 12 V DC/150 mA
C O M M U N I C AT I O N
Installation BUS:
Data transfer indication:
P O W E R S U P P LY
Supply voltage/rated current:
Rated current for full
load on output 12 V DC:
CIB
yellow LED
27 V DC/25 mA, from CIB BUS
100 mA
CONNECTION
Terminal:
max. 2.5 mm2/1.5 mm2 with sleeve
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
Design:
-20 to +55 °C
-30 to +70 °C
IP 20 device, IP 40 mounting in the switchboard
II.
2
any
into a switchboard rail to DIN EN 60715
3-MODULE
DIMENSIONS AND WEIGHT
90 x 52 x 65 mm
Dimensions:
102 g
Weight:
36
IM3-140M
Temperature input, 1-channel and 4-channel TI3-10B, TI3-40B
TI3-10B
These units are designed for connection of one (TI3-10B) to four (TI3-40B) external
temperature sensors.
TI3-40B
Units range TI3 support the connection of the following temperature sensors:
- TC / TZ - 2-wire connections
- Ni1000, Pt1000, Pt100 - 2-wire and 3-wire.
Used in when necessary to take temperatures from different places (for example
large floor heating – diagonal layout of sensors, floor/space, indoor/outdoor
temperature, technological device – boiler, solar heating etc.)
Status of units indicated by green RUN LED on the front panel:
- If the supply voltage is connected (units are powered via the bus CIB),
but there is no communication with the master, RUN LED is lit
continuously.
- If the supply voltage is connected and the unit communicates via
standard CIB, RUN LED flashes.
TI3-10B-40B in TI3 version B is designed for mounting into an installation box.
EAN code
EAN code
Example of connection TI3-10B
TI3-40B 8595188132695
TI3-10B 8595188132886
CIB +
CIB -
TECHNICAL PARAMETERS
INPUT
1x/4xinputs for external thermo sensor TC, TZ,
Temperature input for
Ni1000, Pt1000, Pt100, see accessories
temperature measuring:
Emperature measurement range: by type of sensor, prob from -30°C to 250°C
Converter resolution:
TI3-10B
14 bit
A
CIB
green LED RUN
COM
C O M M U N I C AT I O N
Installation BUS:
Status indication unit:
P O W E R S U P P LY
27 V DC/25 mA, from CIB BUS
temperature sensor t
TC/TZ, Ni, Pt
CONNECTION
0.5 mm2 - 1 mm2
O P E R AT I N G C O N D I T I O N S
Operating temperature:
-20 to +55 °C
Storing temperature:
-30 to +70 °C
Protection degree:
IP 30
Overvoltage category:
II.
Pollution degree:
2
Operating position:
any
Installation:
into installation box
Example of connection TI3-40B
CIB +
CIB -
temperature sensor
TC/TZ, Ni, Pt
t
COM
A
A
A
DIMENSIONS AND WEIGHT
49 x 49 x 13 mm
Dimensions:
Weight:
TI3-10B (22 g), TI3-40B (24 g)
COM
Terminal:
A
Supply voltage/rated current:
temperature sensor
TC/TZ, Ni, Pt t
t
t
37
Thermo input, 6-channel TI3-60M
Unit TI3-60M is designed to connect up to six external temperature sensors.
Units range TI3 support the connection of the following temperature sensors:
- TC / TZ - 2-wire connections
- Ni1000, Pt1000, Pt100 - 2-wire and 3-wire.
It is used in cases where it is necessary to read the temperature, eg floor/room, indoor/
outdoor temperature, process equipment - boiler, solar heating, etc.
Unit status is indicated by green RUN LED on the front panel:
- If the supply voltage is connected (the unit is powered via the bus CIB),
but there is no communication with the master, RUN LED is lit
continuously.
- If the supply voltage is connected and the unit communicates via
standard CIB, RUN LED flashes.
The status on individual temperature inputs is indicated by the relevant red LED on
the front panel – exceeding the scope or interruption of the sensor.
TI3-60M in 3 module is designed for switchboard mounting on DIN rail EN60715.
EAN code
TI3-60M 8595188132893
TECHNICAL PARAMETERS
Example of connection
INPUT
Temperature input for
temperature measuring:
Emperature measurement range:
Converter resolution:
6 x input to externa temperature sensor TC, TZ,
Ni1000, Pt1000, Pt100 see accessories
by type of sensor, probe from -30°C to 250°C
14 bit
CIB +
CIB -
Overload indicator
6x red LED
t
C O M M U N I C AT I O N
Installation BUS:
Status indication unit:
CIB
green LED RUN
A
P O W E R S U P P LY
COM
Supply voltage/rated current:
temperature sensor
TC/TZ, Ni, Pt
t
A
or sensor break
27 V DC/45 mA, from CIB BUS
TI3-60M
CONNECTION
COM
temperature sensor TC/TZ, Ni, Pt
DIMENSIONS AND WEIGHT
Dimensions:
90 x 52 x 65 mm
Weight:
102 g
t
38
A
A
O P E R AT I N G C O N D I T I O N S
Operating temperature:
-20 to +55 °C
Storing temperature:
-30 to +70 °C
Protection degree:
IP 20 device, IP 40 mounting in the switchboard
Overvoltage category:
II.
Pollution degree:
2
Operating position:
any
Installation:
into a switchboard rail to DIN EN 60715
A
0.5 mm2 - 1 mm2
A
Terminal:
t
t
t
temperature sensor
TC/TZ, Ni, Pt
Analog-digital converter ADC3-40M
ADC3-40M is an analog-to-digital converter and is equipped with 4 analog inputs and 2
temperature inputs.
Analog inputs are used to connect analog sensors that generate a voltage or current
signal.
The analog inputs have a resolution of a 14-bit AD converter.
The analog inputs have a common terminal GND.
Analog inputs are configurable in IDM independently as voltage (U) or current (I).
ADC3-40M is designed to capture as analog voltage signals from a weather station.
The red LED on the front panel indicate overload of the analog input or sensor break.
The temperature inputs at the top of the terminal are used to connect the following
temperature sensors:
- TC / TZ - 2-wire connections
- Ni 1000, Pt1000, Pt100 - 2-wire and 3-wire connections.
EAN code
ADC3-40M in 3-MODULE version i s designed for mounting into a switchboard, on a DIN
rail EN60715.
ADC3-40M 8595188132596
TECHNICAL PARAMETERS
Example of connection
INPUTS
CIB +
CIB temperature sensor
TC/TZ, Ni, Pt
A
COM
COM
A
t
COM
t
COM
ADC3-40M
Uref
4x voltage or current input
2x input for external temperature sensor TC,
TZ,Ni 1000, Pt1000, Pt100 see accessories
Depending on the sensor from -30°C to 250°C
Emperature measurement range:
4
Number of inputs:
Galv. separation from inner circuits: No
Overload indicator or sensor break the
Diagnostic:
corresponding red LED
GND
Common terminal:
approximate
Type of converter:
14 bits
Converter resolution:
Input resistance (for voltage ranges): approx. 200 kΩ
Voltage (U) : 0 ÷ +10 V (U)
Input types/ Measuring ranges
0 ÷ +5 V (U)
(for each input individually optional
0 ÷ +2 V (U)
by confi guration in user program
0 ÷ +1 V (U)
IDM):
0 ÷ +0.5 V (U)
Current (I) :
0 ÷ +20 mA (I)
4 ÷ +20 mA (I)
COM
Analog inputs:
Thermo inputs:
C O M M U N I C AT I O N
Installation BUS:
Unit status indication:
CIB
green LED RUN
27 V DC/50 mA, from CIB BUS
CONNECTION
Terminal:
max. 2.5 mm2/1.5 mm2 with sleeve
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
Design:
+
+
+
P O W E R S U P P LY
Supply voltage/rated current:
+
-20 to +55°C
-30 to +70°C
IP 20 device, IP 40 mounting in the switchboard
II.
2
any
into a switchboard rail to DIN EN 60715
3-MODULE
0(4)-20
mA
current
input
without
external
power
supply
12/24 VDC
0(1)-10
V
voltage
input
0(4)-20
mA
current
input
with
external
power
supply
DIMENSIONS AND WEIGHT
Dimensions:
90 x 52 x 65 mm
Weight:
112 g
39
Digital-analog converter DAC3-04B
DAC3-04B is converter of a digital signal to an analog voltage signal.
The converter generates 4 analog voltage signals, which can be regulated according
to type of controlled device, in a range 0-10V or 1-10V.
It serves for regulation and control for devices, which are controlled by 0-10V or 1-10V
signal (lamp ballast for fluorescent lights, dimmers, thermo heads, servo motors,
measuring elements, regulation devices, etc.).
Range of output voltage is adjustable in IDM.
DAC3-04B is equipped with a temperature input for connecting a 2-wire external
sensor TC / TZ.
DAC3-04B in version B is designed for mounting into an installation box.
EAN code
DAC3-04B 8595188132572
TECHNICAL PARAMETERS
Example of connection
INPUTS
Temperature measuring:
Range / accuracy of temp. measuring:
YES, input for external temperature sensor TC/TZ
-20 to +100°C; 0.5°C from the range
CIB +
CIB -
OUTPUTS
Analog voltage output / rated current:
temperature sensor TC/TZ
4x 0(1)-10 V/10 mA
C O M M U N I C AT I O N
Installation BUS:
Status indication unit:
CIB
green LED RUN
DAC3-04B
P O W E R S U P P LY
Supply voltage/rated current:
27 V DC/50 mA, from CIB BUS
CONNECTION
Terminal:
0.5 - 1 mm2
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
-20 to +55 °C
-30 to +70 °C
IP 30
II.
2
any
into installation box
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
40
49 x 49 x 13 mm
33 g
0(1)-10 V
0(1)-10 V
0(1)-10 V
0(1)-10 V
Digital - analog converter DAC3-04M
DAC3-04B is a converter from a digital signal to an analog voltage signal.
The converter generates 4 analog voltage signals, which can be operated, according to
type of controlled device, in a range 0-10V or 1-10V.
It serves for regulation and control for devices, which are controlled by 0-10V or 1-10V
signal (lamp ballast for fluorescent lights, dimmers, thermo heads, servo motors,
measuring elements, regulation devices, etc.).
Range of output voltage is adjustable in IDM.
Converter is equipped with a temperature input for connecting a 2-wire external sensor
TC/TZ (see accessories).
DAC3-04M in 3-MODULE version is designed for mounting into a switchboard, on DIN
rail EN60715.
EAN code
DAC3-04M 8595188132565
Example of connection
TECHNICAL PARAMETERS
INPUT
Analog voltage output/rated current:
4x 0(1)-10 V/10 mA
Range / accuracy of temp. measuring: -20 to +100°C; 0.5°C from the range
OUTPUTS
Analog voltage output/max. current:4x 0(1)-10 V/10 mA
Indication of output overload:
red LED OVERLOAD
C O M M U N I C AT I O N
Installation BUS:
Data transfer indication:
CIB +
CIB -
temperature sensor TC/TZ
CIB
yellow LED
DAC3-04M
RUN
P O W E R S U P P LY
Supply voltage/rated current:
27 V DC/50 mA, from CIB BUS
CONNECTION
Terminal:
max. 2.5 mm2/1.5 mm2 with sleeve
O P E R AT I N G C O N D I T I O N S
Operating temperature:
-20 to +55 °C
Storing temperature:
-30 to +70 °C
Protection degree:
IP 20 device, IP 40 mounting in the switchboard
Overvoltage category:
II.
Pollution degree:
2
Operating position:
any
Installation:
switchboard on DIN rail EN 60715
Design:
3-MODULE
0(1)-10 V
OVERLOAD
0(1)-10 V
0(1)-10 V
0(1)-10 V
DIMENSIONS AND WEIGHT
Dimensions:
90 x 52 x 65 mm
Weight:
102 g
41
Control unit with touch screen EST3
The control unit with touch screen EST3 is a suitable control element of the iNELS
system in places where it is necessary to control multiple devices. The unit replaces
several drivers and enables minimizing the number of switches on the wall.
EST3 features a 3.5 "color touchscreen with an aspect ratio of 3:4. The basic display
resolution is 240 x 320 pixels. The color depth of 16.7 million colors (24 bit color, True
Color).
Use the touch sensing surface to control configured buttons and symbols on the
screen just by a light touch of a finger. Individual symbols on the screen are in the
"Press" animated by the associated output in the system.
EST3 can have a combination of these screens:
- Buttons screen
- Temperature control screen
- Control RGB light sources screen
- Security keyboard screen
Buttons screen can be set in the menu and can be optionally configured according
to user requirements . There are four basic templates of buttons matrix - 2x2, 2x3, 3x3
and 3x4 . The screen can then have up to 12 buttons to control up to 12 appliances or
scenes.
EAN code
EST3 (white frame, white intermediate frame, white back cover) - 8595188177009
EST3 (black frame, dark gray intermediate frame, dark gray back cover) - 8595188177016
In the configuration buttons menu, it is possible to assign a symbol (icon) of the preset
menu to individual keys from the selected templat (48 different symbols - bulb, blinds,
party scene, etc.), possibly write to the button three alphanumeric characters.
The temperature control screen enables correction of the temperature of the selected
heating circuit in the range of ± 5 ° C, or entering of the desired temperature in absolute
value.
The virtual wheel can be used for temperature correction, where you can drag your
finger across the screen to control the temperature by half a degree Celsius.
The temperature correction can also be used instead of the virtual wheel symbols "+
" and "- " .
TECHNICAL PARAMETERS
D I S P L AY
Type:
Aspect ratio:
Visible area:
Backlight:
Touchpad:
Display:
Number of points:
Color Depth:
colored TFT LCD
3:4
52.5 x 70 mm
active
4-wire resistive
3.5”
240 x 320
16.7M (24 bit color)
P O W E R S U P P LY
Supply voltage / rated current:
27V DC/ 150 mA
EST3 units do not have an integrated temperature sensor, or terminals for connection
to an external temperature sensor. Within the IDM software, it is possible to assign any
unit of heat input system iNELS.
The control RGB light sources screen allows you to comfortably control your RGB light
sources and adjust the luminous atmosphere as needed.
For these RGB light sources , it is possible to use the controls on the screen to adjust
the color and brightness. It is also possible to directly set the RGB illumination light
source into white color.
Located in the left upper corner of the screen are 4 indicators that can signal the
status of any logical input / output in the iNELS system.
In the settings menu, you can define the language menu, screen saver, sleep mode,
brightness settings, select the default display and devices display mode of EST3
Unit EST3 is on the CIB represented by one hardware address.
CONNECTION
Connection:
Connecting conductors profile:
terminals
max. 2.5mm2/1.5mm2 with sleeve
EST3 are designed as LOGUS90 devices (EST3 however cannot be placed into multiframes with other devices in this design) and are intended for mounting to installation
box.
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operating position:
Installation:
0 to +55°C
- 20 to +70°C
IP20
II.
2
any
installation box
DIMENSIONS AND WEIGHT
Dimensions
Weight:*:
94 x 94 x 30 mm
EST3 (127 g)
* Weight is listed with plastic frame
42
P O W E R S U P P LY
CIB CIB +
THE SCREENSHOTS
IN2
IN1
IN3
IN4
IN6
IN7
IN9
Circuit
temperature
adjustment Decrease
brightness
IN5
Increase
brightness
IN8
Illumination
in color based
on RGB
IN11
IN10
Output ON/OFF
button
Illumination in
white
IN12
Settings
Device
Information
Button for moving between screens
Legend:
EST3=> settings menu=>design selection=>2x2 - input IN1- IN4
EST3=> settings menu=>design selection=>2x3 - input IN1- IN6
EST3=> settings menu=>design selection=>3x3 - input IN1- IN9
EST3=> settings menu=>design selection=>3x4 - input IN1- IN12
BUTTONS SCREEN
Programming iNELS system functions on each button on the screen units EST3 is the same as programming other digital inputs or events for input or button units.
Buttons can be configured as well as other inputs in the system, both for short and also long press (> 1.5 s).
Buttons (icons) on the screen can be used instead of control outputs for visualization of one of the digital outputs of the system iNELS. This is made possible by assigning button to
the desired output.
In doing so, the button (icons) on the screen EST3 will become signal lamps (illuminated button), showing the state of the associated output.
HEATING CONTROL SCREEN
On the temperature control screen, the temperature of the selected heating circuit can be corrected in the range of ± 5 ° C.
Based on the configuration in the settings menu however, it is possible to directly enter the required absolute temperature value of the given heating circuit.
The virtual wheel can be used for temperature correction, where you can drag your finger across the screen to control the temperature by half a degree Celsius.
The temperature correction can also be used instead of the virtual wheel symbols "+ " and "- " .
RGB LAMP AND LIGHT SOURCE CONTROL SCREEN
The RGB light sources control screen contains controls for managing the desired color and brightness of the RGB light sources.
RGB control screen function is set up so that the colors R, G, B are bound together and simulate the signal level on analog inputs R, G, B and the resulting brightness of the lamp is
linked to a simulated analog input 0 to 100%.
The RGB control display is comprised of several elements and buttons.
- A long press (touch) on the ON/OFF controls the central setting of RGB components and lamp brightness - on/off
- Buttons
in the upper half of the screen are for setting the lamp brightness from 0-100% in 5% increments (see adjustable brightness indicator in %)
in the lower half of the screen are for setting the color comfort and accelerated lamp RGB control. The buttons have a lock function. When pressing
- Buttons
"white illumination“ button, the analog inputs are automatically set to the maximum value of individual color components, which appears as a resulting white light at the RGB
light source output when these components are mixed. Then simply adjust the brightness intensity at the output. When pressing (touching) the button "RGB-based color
illumination“, the "white illumination“ , button automatically unlocks, and the "RGB-based color illumination“ settings button locks..Now the values of analog inputs of individual
RGB color components are preset according to the set cursor in the color wheel of the RGB scale on the EST3.
ADDITIONAL INFORMATION:
Info
gives information on the device and firmware version. Clicking the icon
brings you to the settings menu, used to edit the EST3. The icon
returns to the buttons panel.
The system time is displayed in the upper right corner of the screen.
In the case of request for changing the original screen (panel) buttons, it is always necessary to perform RESET of the device before configuration of icons (buttons).
All inputs and outputs on the EST3 unit can be freely programmed and parameterized using the IDM program.
43
Glass wall touch controllers GSB3
The wall controller with touch controls series GSB3 is a design element (controller) in
the system iNELS with elegant and comfortable control.
GSB3-40
Two-colored indication LED, located in each position of controller, can signal status of
a controlled appliance, as well as the status of any sensor or actuator in the system.
Controllers are 4-channels (GSB3-80), 6-channels (GSB3-60) and 8-channels (GSB380), but currently our department of research and development is working on other
variants of controllers with other graphic changes and for RGB controlling.
All versions are in the same dimension as a basic modular wall-switch (94x94 mm), in
design LOGUS90.
Each controller is equipped with a thermo sensor. It is equipped with two analogdigital inputs (AIN / DIN), and it is possible to connect two potentialless contact or an
external temperature sensor TC / TZ. (for example on floor temperature measurement)
The main advantages against the standard buttons/switches are space saving and
comfort control.
EAN code
GSB3-40 8595188132909
Advantages over conventional switches/buttons include space saving, signaling of
any output system, the ability to measure temperature and also the ability to connect
external buttons or detectors.
Each channel(button) can control any actuator (appliance) in the system. It is also
possible to program various functions or fuction macro (set of functions) to each
button. This allows you to control several appliances with one button simultaneously.
GSB3-60
Each button (channel) can have different functional modes beside lighting control:
a) Classic wall-switch:
- upper button ON, bottom button OFF
b) Button controller (impulse relay):
- first press ON, second press OFF
c) Dimmer:
- short press – ON/OFF,
d) Time switch:
- ON after press, automatically OFF after set time
e) Setting light scenes – for example: for watching TV:
- shutters down
- TV ON
- main light 30% intensity
- wall-lamps 50% intensity.
GSB3 in LOGUS90 design is intended for mounting into wiring box.
EAN code
GSB3-60 8595188132916
GSB3-80
EAN code
GSB3-80 8595188132923
44
TECHNICAL PARAMETERS
INPUTS
GSB3-40
Temperature measuring:
Scope and accuracy of temp. measurement:
Number of control buttons:
Inputs:
Resolution:
Ext. temperature sensor:
GSB3-60
GSB3-80
YES, built-in thermo sensor, NTC
0 to +55°C ; 0.3°C from the range
4
6
8
2x AIN/DIN
by setting bit 10
Yes, the connection between
AIN1/DIN1 and AIN2/DIN2
TC/TZ
Type ext. sensor:
Temperature measurement range:
Temperature measurement accuracy:
-20°C to +100°C
+0.5°C from range
OUTPUTS
Indications:
Number:
two-colored LED (red, green)
2
3
4
C O M M U N I C AT I O N
Installation BUS:
CIB
P O W E R S U P P LY
Supply voltage/rated current:
27 V DC/ 25 - 40 mA, from CIB BUS
CONNECTION
0.5 - 1 mm2
Terminals:
O P E R AT I N G C O N D I T I O N S
-20 to +55 °C
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operation position:
Installation:
-30 to +70 °C
IP 20
II.
2
any
into installation box
DIMENSIONS AND WEIGHT
Dimensions:
Weight:
94 x 94 x 30 mm
70 g (without frame)
Example of connection
temperature sensor TC/TZ
2x input for potentialless contact
(button, motion sensor, etc.)
AIN1/DIN1
AIN1/DIN1
AIN2/DIN2
AIN2/DIN2
GSB3
CIB
CIB
CIB
CIB+
I
I
CIB
I
CIB
CIB
I
+
-
CIB+
GSB3
CIB+
Wall switch button
CIB+
Wall switch button
+
-
CIB
CIB
45
Wall group controllers with low-upstroke control WSB3
WSB3-20
Wall controllers with low-upstroke control (line) WSB3 are the main and most frequently
used units (controller) in the iNELS system.
WSB3-40
Built-in micro-buttons with low upstroke offer elegant and easy control.
Two-colored indication LED, located in each position of controller, can signal status
of controlled appliance, and also status of any sensor or actuator in the system.
Controllers are designed as two-channel (WSB3-20) or four-channel (WSB3-40).
All versions are in the same dimension as a basic modular wall-switch (94x94 mm), in
Logus90 design and can be combined into multiframes with other devices of this line.
Each controller is equipped with a temperature sensor. It is also equipped with two
analog/digital inputs (AIN/DIN), which can be used to connect two potentialless
contacts or one external temperature sensor TC/TZ (e.g. for measuring floor
temperature).
EAN code
EAN code
WSB3-20 8595188132343
WSB3-40 8595188132336
Each channel (button) can control any actuator (appliance) in the system. It is also
possible to program various functions or macro function (set of functions) to each
button. Allowing you to control several appliances with one button simultaneously.
TECHNICAL PARAMETERS
INPUTS
Temperature measuring:
Scope and accuracy of temp. measurement:
Number of control buttons:
Inputs:
Resolution:
Ext. temperature sensor:
WSB3-20
WSB3-40
YES, built-in temperature sensor, NTC
0 to +55°C ; 0.3°C from the range
2
4
2x AIN/DIN
by setting, bit 10
Yes, the connection between
AIN1/DIN1 and AIN2/DIN2
Type ext. sensor:
Temperature measurement range:
Temperature measurement accuracy:
TC/TZ
-20°C to +100°C
+0,5°C from range
OUTPUTS
Indication:
Number of outputs:
Advantages over conventional switches / buttons include space saving, signaling of
any output system, the ability to measure temperature and the possibility to connect
external buttons or detectors.
two-colored LED (red, green)
1
Each button (fold) can have different functional modes beside lighting control:
a) Classic wall switch:
- upper button ON, bottom button OFF
b) Button controller (impulse relay):
- first press ON, second press OFF
c) Dimmer:
- short press – ON/OFF,
d) Time switch:
- ON after press, automatically OFF after set time
e) Setting light scenes – for example: for watching TV:
- shutters down
- TV ON
- main light 30% intensity
- wall lamps 50% intensity
WSB3 in LOGUS90 design is designed for mounting into an installation box.
2
C O M M U N I C AT I O N
Installation BUS:
P O W E R S U P P LY
Supply voltage/rated current:
CONNECTION
Terminals:
CIB
27 V DC/25 mA, from CIB BUS
Example of connection
temperature sensor TC/TZ
0.5 - 1 mm2
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operation position:
Installation:
-20 to +55 °C
-30 to +70 °C
IP 20
II.
2
any
into installation box
DIMENSIONS AND WEIGHT
85.6 x 85.6 x 30 mm
AIN2/DIN2
Wall switch button
CIB
CIB
CIB+
WSB3
CIB+
70 g (without frame)
AIN1/DIN1
I
94 x 94 x 30 mm
I
Dimensions (plastic):
Dimensions (metal, glass, wood, granite):
Weight:
+ CIB
- CIB
46
Wall card reader WMR3-11
WMR3-11 is a wall-mounted card reader that is designed for read contactless media
(smart cards, key chains, etc.).
It can be used for security system controlling (locking/unlocking), as a access system
(doors, gates, etc.) and also as a control of appliances operating (due to the designed
permitions).
WMR3-11 supports RFID media with frequence 125 kHz and with IC type Unique 64 bits
Ask Manchester.
It contains two buttons (UP/DOWN) with same functions as WSB3-20.
Indication two-color LED in the controller cover can indicate not only the status of
controlled appliance, but also the status of any sensor or actuator in the system.
WMR3-11 is also equipped with 8A relay output with changeover contact AgSnO2, by
which controlled devices can be switched directly (or any actuator in the system can
be set in software IDM).
EAN code
WMR3-11 8595188132756
WMR3-11 in LOGUS90 design is intended for mounting into wiring box.
TECHNICAL PARAMETERS
INPUTS
Number of control buttons:
2
CARD READER
Type:
Supported cards:
IC Type:
Example of connection
RFID 125 kHz ± 6 kHz
ISO Card Unique
Unique 64 Bits RF/64 ASK Manchester,
compatible with EM4100
8–14 V AC/DC
1x changeover 8A / AgSnO2
red, green LED
piezo-changer
230V AC/ 30V DC
2000 VA/AC1; 240 W/DC
20 A/<3s
electric door lock
OUTPUTS
Output:
Indication:
Acustic output:
Switching voltage:
Switching output:
Peak current:
Insulation voltage between relay
outputs and internal circuits:
Minimal switched current:
Switching frequency without load:
Switching frequency with rated load:
Mechanical life:
Electrical life AC1:
3.75 kV, SELV according to EN 60950
10 mA / 10 V
300 min-1
15 min-1
1 x 107
1 x 105
WMR3-11
C O M M U N I C AT I O N
Installation BUS:
CIB BUS
P O W E R S U P P LY Í
Supply voltage/rated current:
27 V DC/50 mA, from CIB
CIB +
CIB -
CONNECTION
Data:
Network:
Operating temperature:
Storing temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operation position:
Installation:
terminals, 0.5 - 1 mm2
max. 2.5 mm2/1.5 mm2 with sleeve
-20 to +55 °C
-30 to +70 °C
IP20
II.
2
any
into installation box
DIMENSIONS AND WEIGHT
85.6 x 85.6 x 30 mm
Dimensions (plastic):
Dimensions (metal, glass, wood, granite): 94 x 94 x 30 mm
82 g (without frame)
Weight:
47
Digital room thermo-regulator IDRT3-1
With IDRT3-1 the circuit heating/cooling can be corrected to within ± 5 ° C, or you can
enter the desired temperature in the room in absolute value.
The display shows the current temperature and after pressing one of two buttons
under the display, you can control the desired temperature.
Readability improves after pressing one of the buttons to activate the backlight.
Heating/cooling circuit is assigned with a thermo-regulator using iNELS Designer and
Manager (IDM) .
In the case of temperature correction within ± 5 °C, this change is valid until the next
time mark within the time schedule established in IDM .
IDRT3 -1 in design LOGUS90 is intended for mounting into an installation box.
EAN code
IDRT3-1 8595188132510
TECHNICAL PARAMETERS
INPUTS
Temperature measuring:
Range / accuracy of temp.measuring:
Heating/cooling circuit correction:
Manual ontrol of heating/
cooling circuit:
Example of connection
IDRT3-1
YES, built-in thermo sensor NTC
0 to +55°C; 0.3°C from range
±5°C or abs. value
2 x buttons
C O M M U N I C AT I O N
Installation:
Display:
Backlight:
P O W E R S U P P LY
Supply voltage/rated current:
CIB
symbol display
YES
27 V DC/20 mA from CIB BUS
CONNECTION
Terminals:
0.5 - 1 mm2
O P E R AT I N G C O N D I T I O N S
Operating temperature:
Protection degree:
Overvoltage category:
Pollution degree:
Operation position:
Installation:
0 to +50 °C
IP 20
II.
2
vertical, downward with CIB terminal
into installation box
DIMENSIONS AND WEIGHT
Dimensions (plastic):
Dimensions (metal, glass, wood, granite):
Weight:
48
85.6 x 85.6 x 20 mm
94 x 94 x 20 mm
73 g
CIB +
CIB -
Notes
49
Application iNELS Home Control iHC
Controlling
Controll
ing
appliances
Dimming
Stmívání
lights
osvětlení
Controlling
Controll
ing
blinds í
Regulace
Heating
vytápění
regulation
Controlling
Controll
ing hous
housee
hold appliances
Controlling
Controll
ing
appliances
Stmívání
Dimming
osvětlení
lights
Controlling
Controll
ing
blinds
Regulace
Heating
vytápění
regulation
Controlling
Controll
ing hous
housee
hold appliances
Weather
Weather
station
Video
Vide
o camera
camerass
(outdoor/indoor) í)
Air
conditioning
Door
communicator
Video
Vide
o Zone
Zone
(controlling via TV)
Weather
Weather
station
Video camera
Video
camerass
(outdoor/indoor)
Air
conditioning
Door
communicator
Video
Vide
o Zone
Zone
(controlling via TV)
Connection Server
iMM Server
It serves as a connection between iNELS
system units and another devices because
it allows communication between devices
with different protocols. Except the
common controlling of iNELS electroinstallation, it enables also e.g. control of
air conditioning through iHC application
or control of Miele household appliances
through Video zone.
iHC-MA
iHC-TA
Smartphone
Tablet
iMM multimedia server has functions of
Connection Server. It enables you to share
pictures, music, video, TV and internet
between Audio and Video zones which
are placed in one house. It also enables
you to control and monitor all units in
iNELS electro-installation through the
Videozones (TV).
iHC-MI
iPhone
iHC-TI
iPad
Applications for system control for your tablet or smartphone
Development of smartphones and tablets and development of applications for these devices go together. You can control your electro-installation
through the applications in your iPhone, iPad, Smartphone or tablet with the Android operating system. As opposed to our competitors, we provide
you a solution assuring you that your household appliances can be controlled through just one application. You will find here whatever you need – it
provides you full managing, monitoring and checking of your house.
You can control not only lighting or heating, but also it enables you to switch the TV programs, play music and control air conditioning. iHC is
an acronym of iNELS Home Control and letters after the hyphen means devices (T= tablet, M = mobile / smartphone) and operating system
(Android = A, I = iOS / Apple).
The applications are available on AppleStore and GooglePay (former AndroidMarket).
50
Applications for control iNELS using phones, tablets and TV
iNELS BUS System
iNELS RF Control
(bus electro installation)
(wireless electro installation)
Samsung
iOS
Android
Socket
Garage doors,
gates
RGB bulbs,
LED strips
Scenes
Heating
Multimedia
Cameras
Air-conditioning
(LG)
Recuperation
(Air Pohoda, Atrea)
Coolmaster
(LG, Fujitsu, Mitsubishi)
Home appliances
(MIELE)
Weather station
Measurement and
visualization of energy
Door communicator and
Intercom
Other code:
Smart TV
Tablet
Phone
iPad
iPhone
Tablet
Phone
iPad
iPhone
Smart TV
iHC-TA
iHC-MA
iHC-TI
iHC-MI
iHC-TARF
iHC-MARF
iHC-TIRF
iHC-MIRF
iHC-STV
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
О
О
О
X
X
X
✓
✓
О
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
859188150552
8595188150590
О
Blinds
iOS
О
Lighting
Android
8595188146357 8595188160513 8595188149822 8595188149792 8595188149877 8595188149860 859588150545
О
Applications are free to download at
or
Coming Soon
✓
Supported
X
not supported
and are supported by Android OS 2.3 or later and iOS
www.elkoep.cz/aplikace
51
Thermodrive TELVA 230 V, TELVA 24 V
The thermo electric drive TELVA is intended for zone or individual regulation with high
differential pressures.
Regulating thermostatic valves of floor, radiator and convector heating.
Stepped through the valve-adapter VA, the thermodrive can be used for a wide range
of thermostatic valves which are available on the market.
Thermo drive TELVA is used to regulate heating in the iNELS RF Control a iNELS BUS
Systems:
- TELVA 230 V and TELVA 24 V with any system switching actuator
- TELVA 230 V and TELVA 24 V : work in the open / closed modes.
Main features:
- noise-free operation
- design: without voltage opened / without voltage closed
- valve position visual indicator.
Application:
TELVA 230V and TELVA 24V standard with valve-adapter VA 80 * in the low version with
rod M30 x 1.5 (white-gray). This valve-adapter is compatible with valves Manufacturers:
Heimeier, MNG (from 1998), Onda, Oventrop (from 1997), Schlosser, Beulco (from
2005), Bohnish-BK (from 1998), Cazzaniga, Dumser, Honeywell&Braukmann, Ivar, Reich
(distributor), Bohnisch-SBK.
EAN code
TELVA 230V, NC 8595188172042
TELVA 230V, NO 8595188172059
TELVA 24V, NC 8595188172066
TELVA 24V, NO 8595188172073
TECHNICAL PARAMETERS
Operating voltage:
Switching current max:
Operating current:
Closing / opening time:
Power input:
Protection:
Settings:
Stopping force:
Cable length:
Connecting wire:
Media temperature:
Color:
Dimensions h/w/d:
TELVA 230 V
TELVA 24 V 230V, 50/60 Hz
300 mA for max. 200 ms
8 mA
dtto 3 min.
1.8 W
IP 54/II
4 mm
100 N ±5 %
1m
2 x 0.75 mm2
0 to +100 °C
white RAL 9003
55+5 x 44 x 61 mm
24V, 50/60 Hz
250 mA for max. 2 min
75 mA
dtto 3 min.
1.8 W
IP 54/II
4 mm
100 N ±5 %
1m
2 x 0.75 mm2
0 to +100 °C
white RAL 9003
55+5 x 44 x 61 mm
* Note: The valve adapter VA-80 may not be compatible with all types valves of listed manufacturers. For these valves and other manufacturers other types of valve adapter can be supplied.
52
Thermo sensors TC, TZ
Temperature sensors TC and TZ are designed for temperature sensing
TC
TZ
The temperature sensors are made from NTC and sealed in a metal tube by
thermoconductive glue
Thermal contact between thermistor and thermal sensor surroundings
Sensor TZ is suitable mainly in extreme temperatures
2 types of thermal sensors:
- TC - service wire to sensor TC is made of conductor CYSY 2D x 0.02 ˝
- TZ - sensor TZ is made of wire VO3SS-F 2D x 0.5mm with silicon insulation
Dimensions of the sensors TC
EAN code
EAN code
8595188110075
8595188110617
8595188110082
8595188110099
TZ-0
TZ-3
TZ-6
TZ-12
TC
Range:
Scanning element:
τ65 - in air/ in water:
τ95 - in air/ in water:
Cable material:
Terminal material:
Protection degree:
8595188140591
8595188110600
8595188110594
8595188110587
TZ
- TZ-0 - 4.5 g (0.16 oz.)
- TZ-3 - 106 g (3.74 oz.)
- TZ-6 - 216 g (7.6 oz.)
- TZ-12 - 418g (14.7 oz.)
Diagram of sensor warm up via air
0 °C to +70 °C (32 °F to 158 °F) -40 °C to +125 °C (-40 °F to 257 °F)
NTC 12K 5 %
NTC 12K 5 %
62 s / 8 s
92 s / 23 s
216 s / 23 s
306 s / 56 s
silicone
Heat-resistant PVC
nickel-coated copper
Heat-resistant PVC
IP 67
IP 67
70
PVC
Silicon
60
50
Temperature (oC)
TC-0
TC-3
TC-6
TC-12
Dimensions of the sensors TZ
- TC-0 - 5 g (0.2 oz.)
- TC-3 - 108 g (3.8 oz.)
- TC-6 - 213 g (7.5 oz.)
- TC-12 - 466 g (16.4 oz.)
40
30
20
10
O
O
Temperature ( C / F)
Sensor resistance(kΩ)
14.7
9.8
6.6
4.6
3.2
2.3
20
30
40
50
60
70
0
00:00
02:53
05:46
08:38
11:31
14:24
17:17
st [min]
Time
(min)
PVC -reaction to water temperature from 22.5 °C to 58 °C (from 72.5 °F to 136.4 °F)
Silicone - reaction to water temperature from 22.5 °C to 63.5 °C (from 72.5 °F to 144.5 °F)
Temperature sensors for range
0°C to +70°C (32°F to 158°F)
Temperature sensors for range
-40°C to +125°C (-40°F to 257°F)
TC-0 - temperature sensor can be connected directly to terminal block
TZ-0 - temperature sensor can be connected directly to terminal block
(lenght of sensor 110mm/ 4.33˝)
(lenght of sensor 110mm/ 4.33˝)
TC-3 - temperature sensor 3 m (9.8´)
TZ-3 - temperature sensor 3 m (9.8´)
TC-6 - temperature sensor 6 m (19.7´)
TZ-6 - temperature sensor 6 m (19.7´)
TC-12 - temperature sensor 12 m (39.4´)
TZ-12 - temperature sensor 12 m (39.4´)
Sensor TC drawing
Sensor TZ drawing
22.65 mm
20 mm
8.2 mm
Sensor TC-3 photo
6.2 mm
Sensor TZ-3 photo
53
Loadability of contacts
SA3-02B; SA3-06M; SA3-012M; WMR3-11
Type of load
cos φ ≥ 0.95
M
AC1
Contact materialAgSnO2
contact 8A
250V / 8A
M
AC2
250V / 2.5A
AC3
250V / 1.5A
230V / 1.5A (345VA)
K
Type of load
Contact materialAgSnO2
contact 8A
HAL.230V
AC5a
uncompensated
AC5a compensated
AC5b
AC6a
AC7b
AC12
230V / 1.5A (345VA)
till max output C=14uF
250W
250V / 4A
250V / 1A
250V / 1A
M
M
AC13
AC14
AC15
DC1
DC3
DC5
DC12
DC13
DC14
x
250V / 3A
250V / 3A
24V / 8A
24V / 3A
24V / 2A
24V / 8A
24V / 1A
x
LBC3-02M; SA3-01B; SA3-02M; SA3-04M
Type of load
cos φ ≥ 0.95
AC1
Contact materialAgSnO2
contact 16A
250V / 16A
M
M
AC2
AC3
250V / 5A
250V / 3A
Type of load
Contact materialAgSnO2
contact 16A
HAL.230V
AC5a
uncompensated
AC5a compensated
AC5b
AC6a
AC7b
AC12
230V / 3A (690VA)
230V / 3A (690VA)
till max output C=14uF
1 500W
x
250V / 3A
250V / 10A
M
M
K
AC13
AC14
AC15
DC1
DC3
DC5
DC12
DC13
DC14
250V / 6A
250V / 6A
250V / 6A
24V / 16A
24V / 6A
24V / 4A
24V / 16A
24V / 2A
24V / 2A
SA3-02B/Ni; SA3-06M/Ni; SA3-012M/Ni
Type of load
Contact materialAgNi *
contact 8A
cos φ ≥ 0.95
M
M
AC1
AC2
AC3
250V / 8A
250V / 2.5A
250V / 1.5A
230V / 1.5A (345VA)
Type of load
Contact materialAgNi *
contact 8A
HAL.230V
AC5a
uncompensated
K
AC5a compensated
AC5b
AC6a
AC7b
AC12
x
400W
x
250V / 1.5A
250V / 5A
M
M
AC13
AC14
AC15
DC1
DC3
DC5
DC12
DC13
DC14
250V / 3A
250V / 3A
250V / 3A
24V / 8A
24V / 3A
24V / 2A
24V / 8A
24V / 1A
24V / 1A
AC5a compensated
AC5b
AC6a
AC7b
AC12
x
800W
x
250V / 3A
250V / 10A
M
M
SA3-01B/Ni; SA3-02M/Ni; SA3-04M/Ni
Type of load
Contact materialAgNi *
contact 16A
cos φ ≥ 0.95
M
AC1
AC2
AC3
250V / 16A
250V / 5A
250V /3A
230V / 3A (690VA)
K
AC13
AC14
AC15
DC1
DC3
DC5
DC12
DC13
DC14
250V / 6A
250V / 6A
250V / 6A
24V / 16A
24V / 6A
24V / 4A
24V / 16A
24V / 2A
24V / 2A
Demonstrated symbols are informative
*Products with AgNi contact only up on request for extra charge.
54
HAL.230V
AC5a
uncompensated
Type of load
Contact materialAgNi *
contact16A
M
bulbs, halogen bulbs
12–24V low-voltage 12–24V low-voltage bulbs,
bulbs, coil transformers electric transformers
Load
DA3-22M
energy-saving
fluorescent tubes
LEDs
230V AC
R
L
C
dimmable




dimmable
entering edge
trailing edge



MINIMUM LOAD
MINIMUM LOAD
RELAY CONTACT
mV
V/mA
AgSnO2
1000
10/100
RELAY CONTACT
AgNi
Explanations
El. bulbs loads:
el. bulb, halogen light
R,L,C
10
control method
mV
V/mA
300
5/10
Explanations
(R)
Switch:
switch - control contact of various device
Dimmer with defined load:
R - resistive, L - inductive, C - capacitive
Button:
control button
Fluorescent light:
fluorescent lights uncompensated
Control module:
analog control module 0 - 10 V
Fluorescent light:
fluorescent light compensated in series
Motor
Fluorescent light:
fluorescent light compensated in parallel
AC1
non-inductive or low inductive loads
resistive furnaces
Fluorescent light:
fluorescent light economical
AC3
motors with short-way armatour, start-up
of motors in operation
Elektronic ballasts for fluorescent
AC15
managemens of AC electromagnetic loads
DC1
non-inductive or low inductive loads,
resistive furnaces
Inductive loads (transformers):
(L)
feromagnetic and toroid transformers for lights with various voltage.
55
Case studies
JA3-02B
HOTEL ROOM
SHUTTER ACTUATOR
4-CHANNEL WALL CONTROLLER
Switching actuator for controlling shutters,
blinds and awnings Contains temperature input.
Mounting in an installation cabinet.
Moun
Mou
Controls lights, binds, shutters and other appliances. Contains a temperature sensor. Design
Elegant or LOGUS90.
WSB3-20G/40G
ELEMENTS IN THE SWITCH BOARD
EST-3
CU3-01M - CENTRAL UNIT
THE „GO-BETWEEN“ between the user program environment
and other sensors and actuators connected to the bus.
PS3-100/iNELS - POWER SUPPLY
Switched stabilized power supply. Used to feed control machines within the framework of the iNELS intelligent electrical
TOUCH SCREEN PANEL
NEL
EL
Control unit with touch screen display
play
a with which
it is possible to control elements on the bar by just
lightly touching the screen. Designed for surface
mounting or in an installation cabinet.
BPS3-01M - BUS SEPARATOR
Serves for impedance separation of the CIB bus from the
voltage supply.
SA3-04M - SWITCHING ACTUATOR
SA3-01B
Designed for switching different appliances and loads potential
free contact.
SINGLE-CHANNEL SWITCHING ACTUATOR
This is designed to switch all kinds of appliances
and loads by dry contact. Designed for mounting
in an installation cabinet.
LEGEND:
Switching appliances
WSB3-20G/40G
Heating regulation
DA3-22M - DIMMING ACTUATOR
Designed for dimming light sources RLC (automatic detection),
can also be used to switch appliances.
Controlling lighting
4 CHANNEL WALL CONTROLLER
SWITCHING ACTUATOR 1-FOLD
Controls lights, jalousies, shutters and other
appliances, in LOGUS90 design.
The unit can be used for example to control the Thermodriver. In to installation box.
SA3-01B
FAMILY HOME
Controlling binds, garage
IM3-40B
BINARY INPUT UNIT
Designed for connection of 2, 4
or 8 devices with potential-less
contacts (switches, buttons, PIR
sensors, fire and gas detectors
etc.).
JS-20 PIR
PIR MOTION DETECTOR
EST-3
TOUCH PANEL
Rotects your house against move of unfamiliar people inside the house in time when
you are not at home.
Control unit with touch-screen display by which
it is possible to control bus units by a slight touch
of a display. In version for mounting on surface or
iinto an installation box.
SD-280
0 - 100 V
SMOKE DETECTOR
Product serves for a detection of fire
danger in interior of residential or
commercial buildings.
WMR3-11
CARD READER
Is intended for reading of contactless
media ( chip cards, key chains,..)
UNITS IN A SWITCHBOARD
IDRT3-1
CU3-01M - CENTRAL UNIT
MEDIATOR,, among user program surrounding and other sensors and actuators connected to bus.
PS3-100/iNELS - POWER SUPPLY
Stabilized switching power supply, serves for supplying of control automats in intelligent electro-installation iNELS.
BPS3-02M - BUS SEPARATOR
DIGITAL THERMO REGULATOR
Designed for impedance separation of CIB from supply
voltage power.
Control unit for a correction of heating circle
in iNELS system, available in LOGUS 90design.
SA3-012M - SWITCHING ACTUATOR
Designed for switching various appliances and
loads by a floating contact .
DA3-22M - DIMMING ACTUATOR
Designed for dimming of lights with RLC characteristic (automatic detection). It is also suitable for switching of appliance.
2 pc
JA2-02B
DAC3-04M - CONVERTER (DIGITAL - ANALOG)
Designed for switching various appliances and
loads by a floating contact.
GSM3-01 - GSM GATE
Js designed for communication with iNELS system, via SMS
message commands sent from mobile GSM phones.
LEGEND:
56
Switching appliances
SHUTTER ACTUATOR
Switching actuator for operating
of shutters, venetian blinds, sunblinds, thermo input is included,
mounting into installation box.
2 pc
Heating regulation
Controlling lighting
Controlling shutters
Detectors
WSB3-20G/40G
4 CHANNEL WALL CONTROLLER
SWITCHING ACTUATOR 1-FOLD
Controls lights, jalousies, shutters and other
appliances, in LOGUS90 design.
The unit can be used for example to control the Thermodriver. In to installation box.
SA3-01B
IM3-40B
BINARY INPUT UNIT
Designed for connection of 2, 4
or 8 devices with potential-less
contacts (switches, buttons, PIR
sensors, fire and gas detectors
etc.).
FAMILY HOME
JS-20 PIR
PIR MOTION DETECTOR
EST-3
TOUCH PANEL
Rotects your house against move of unfamiliar people inside the house in time when
you are not at home.
Control unit with touch-screen display by which
it is possible to control bus units by a slight touch
of a display. In version for mounting on surface or
iinto an installation box.
SD-280
0 - 10
0V
SMOKE DETECTOR
Product serves for a detection of fire
danger in interior of residential or
commercial buildings.
WMR3-11
CARD READER
Is intended for reading of contactless
media ( chip cards, key chains,..)
UNITS IN A SWITCHBOARD
IDRT3-1
CU3-01M - CENTRAL UNIT
MEDIATOR,, among user program surrounding and other sensors and actuators connected to bus.
PS3-100/iNELS - POWER SUPPLY
Stabilized switching power supply, serves for supplying of control automats in intelligent electro-installation iNELS.
BPS3-02M - BUS SEPARATOR
DIGITAL THERMO REGULATOR
Designed for impedance separation of CIB from supply
voltage power.
Control unit for a correction of heating circle
in iNELS system, available in LOGUS 90design.
SA3-012M - SWITCHING ACTUATOR
Designed for switching various appliances and
loads by a floating contact .
DA3-22M - DIMMING ACTUATOR
Designed for dimming of lights with RLC characteristic (automatic detection). It is also suitable for switching of appliance.
2 pc
JA2-02B
DAC3-04M - CONVERTER (DIGITAL - ANALOG)
Designed for switching various appliances and
loads by a floating contact.
GSM3-01 - GSM GATE
Js designed for communication with iNELS system, via SMS
message commands sent from mobile GSM phones.
LEGEND:
Switching appliances
multimedia extension
iTP-B
Controlling lighting
Heating regulation
Controlling shutters
TV
TELEVISION
FA M I LY H O U S E
SHUTTER ACTUATOR
Switching actuator for operating
of shutters, venetian blinds, sunblinds, thermo input is included,
mounting into installation box.
2 pc
Detectors
iPHONE
Due to a clear projection on a TV screen you have
a perfect overview about happening inside home
and even outside of it. It is only necessary to install
cameras and connect them with the system.
iHC-M, iPHONE/Smart phone
Comfortable control of home automation systems
via your iPHONE, Smart phone.
TOUCH PANEL
iHC-T, Touch tablet
Is a complement of iNELS system which easily
merges with your household due to its elegant
an even
design. You can place it anywhere you wa
want,
to your bathroom.
To control lighting, heating, blinds, cameras,
multimedia (music, film, TV, photo) and other
system functions can also use your iPad or other
tablet with Android OS.
iTP-T
iMM Client
iMM Client
Enables to control all iNELS functions
via TV. Elegant noiseless version.
Capacity of store is 250 GB.
LARA
Audiozóna, LARA – přehrávač audiozóny
IP HLÁSKA
Audiozóna umí přehrávat soubory z multimediálních
serverů, ale také streamovat internetová rádia či
využít k přehrání zdroj externí hudby. To vše kdekoliv
v domě a v elegantním designu LOGUS90.
SSATELIT
KAMERA
SATELLITE
INDOOR CAMERA
Via satellite receiver you can watch up
to 4 satellite channels at once, if they are
placed on a same transponder.
System supports connection, display and control of IP cameras including PTZ ( position control,
image extension, record,…)
LEGEND:
Switching appliances
Heating regulation
Light control
DOORPHONE COMMUNICATOR
Door communicator with top technologies and
a unique design. It is a communication system
supporting voice and movie transmission.
Shutter control
Media
57
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement