Sherwood SD-860 Operating instructions

Sherwood SD-860 Operating instructions
SD-860
Introduction
READ THIS BEFORE OPERATING YOUR UNIT
This symbol is intended to alert the user to the
presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of
electric shock to persons.
CAUTION
WARNING
: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
FCC INFORMATION(FOR U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION : Any changes or modifications in construction of this device which are not
expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
CLASS 1
LASER PRODUCT
CAUTION
Invisible laser radiation when the unit is open.
Do not stare into beam.
CAUTION : USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
2
SAFETY INSTRUCTIONS
1. Read Instructions - All the safety and operating instructions should
be read before the product is operated.
2. Retain instructions - The safety and operating instructions should
be retained for future reference.
3. Heed Warnings - All warnings on the product and in the operating
instructions should be adhered to.
4. Follow Instructions - All operating and use instructions should be
followed.
5. Cleaning - Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
6. Attachments - Do not use attachments not recommended by the
product manufacturer as they may cause hazards.
7. Water and Moisture - Do not use this product near water - for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in
a wet basement, or near a swimming pool; and the like.
8. Accessories - Do not place this product on an unstable cart, stand,
tripod, bracket, or table. The product may fall, causing serious injury
to a child or adult, and serious damage to the product. Use only with
a cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any mounting of the product
should follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
9. A product and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the product
and cart combination to overturn.
10. Ventilation - Slots and openings in the
cabinet are provided for ventilation and to
ensure reliable operation of the product and
to protect it from overheating, and these
openings must not be blocked or covered.
The openings should never be blocked by
PORTABLE CART WARNING
placing the product on a bed, sofa, rug, or
other similar surface. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been adhered to.
11. Power Sources - This product should be operated only from the
type of power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult your product
dealer or local power company. For products intended to operate
from battery power, or other sources, refer to the operating
instructions.
12. Grounding or Polarization - This product may be equipped with a
polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet only one
way. This is a safety feature. If you are unable to insert the plug
fully into the outlet, try reversing the plug. If the plug should still fail
to fit, contact your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
Alternate Warnings - This product is equipped with a three-wire
grounding-type plug, a plug having a third(grounding) pin. This plug
will only fit into a grounding-type power outlet. this is a safety
feature. If you are unable to insert the plug into the outlet, contact
your electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the grounding-type plug.
13. Power-Cord Protection - Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the
product.
14. Outdoor Antenna Grounding - If an outside antenna or cable
system is connected to the product, be sure the antenna or cable
system is grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with
regard to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for the
grounding electrode. See Figure 1.
Figure 1
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
15. Lightning - For added protection for this product during a lightning
storm, or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect the antenna or
cable system. This will prevent damage to the product due to
lightning and power-line surges.
16. Power Lines - An outside antenna system should not be located in
the vicinity of overhead power lines or other electric light or power
circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken
to keep from touching such power lines or circuits as contact with
them might be fatal.
17. Overloading - Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of fire
or electric shock.
18. Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.
19. Servicing - Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified service personnel.
20. Damage Requiring Service - Unplug this product form the wall
outlet and refer servicing to qualified service personnel under the
following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper adjustment
of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to
its normal operation.
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance - this
indicates a need for service.
21. Replacement Parts - When replacement parts are required, be
sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the
original part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.
22. Safety Check - Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
23. Wall or Ceiling Mounting - The product should be mounted to a
wall or ceiling only as recommended by the manufacturer.
24. Heat - The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
Notes:
1. Item 12 is not required except for grounded or polarized product.
2. Item 14 and 16 are not required except for units provided with
antenna terminals.
3. Item 14 complies with UL in U.S.A.
3
FOR YOUR SAFETY
Units shipped to the U.S.A and Canada are designed for operation on 120 V AC only.
Safety precaution with use of a polarized AC plug.
However, some products may be supplied with a nonpolarized plug.
U.S.A
and
CANADA
120 V
CAUTION
: To prevent electric shock, match wide blade of plug to wide slot, fully
insert.
ATTENTION : Pour éviter chocs électriques, introduire la lame la plus large de la fiche
dans la borne correspondante de la prise et pousser jusqu’ au fond.
CHINA,
EUROPE,
AUSTRALIA
and other
countries
220 V
240 V
The available power supply voltage differs according to country or region. However,
this unit is equipped with an Automatic Voltage Selector.
The power supply voltage of the area where the unit will be used automatically
meets the required voltage within the range of AC 220 - 240 V, without any manual
voltage adjustment.
To ensure safe operation, the three-pin plug supplied must be inserted only into a
standard three-pin power point which is effectively earthed through the normal
household wiring. Extension cords used with the equipment must be three-core and
be correctly wired to provide connection to earth.
Improper extension cords are a major cause of fatalities. The fact that the equipment
operates satisfactorily does not imply that the power point is earthed and that the
installation is completely safe. For your safety, if in any doubt about the effective
earthing of the power point, consult a qualified electrician.
CAUTION
• Leave a space around the unit for sufficient ventilation.
• Avoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating
equipment.
• Keep the unit free from moisture, water, and dust.
• Do not let foreign objects in the unit.
• The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers,
table-cloths, curtains, etc.
• No naked flame sources, such as lighted candles, should be placed on the unit.
• Please be care the environmental aspects of battery disposal.
• The unit shall not be exposed to dripping or splashing for use.
• No objects filled with liquids, such as vases, shall be placed on the unit.
• Do not let insecticides, benzene, and thinner come in contact with the set.
• Never disassemble or modify the unit in any way.
Notes on the AC power cord.
• The unit is not disconnected from the AC power source(mains) as long as it is connected to the wall outlet,
even if the unit has been turned off.
• When disconnecting the power cord from the wall outlet, always pull the plug, not the power cord.
• Disconnect the plug from the wall outlet when not using the unit for long periods of time.
PRECAUTIONS
Moisture condensation
Moisture may form on the lens in the following conditions.
• Immediately after a heater has been turned on.
• In a steamy or very humid room.
• When this unit is moved from a cold place to a warm one.
If moisture forms inside this unit, it may not operate properly.
In this case, turn on the power and wait about one hour for the moisture to evaporate.
If there is noise interference on the TV while a broadcast is being received.
Depending on the reception condition of the TV, interference may appear on the TV screen while you are
watching a TV broadcast and this unit is left on. This is not a malfunction of this unit or the TV. To watch a TV
broadcast, turn off this unit.
Do not transport this unit with discs left in it.
Do not place on the component such as amplifier or receiver that generates heat.
If so, the temperature inside this unit rises and malfunction may occur.
4
CONTENTS
• Introduction
READ THIS BEFORE OPERATING YOUR UNIT
| 2
• System Connections
CONNECTING TO A/V AMPLIFIER OR RECEIVER
| 6
CONNECTING TO TV WITH AUDIO AND VIDEO INS
| 9
CONNECTING TO TV WITH SCART CONNECTOR(Regional Option)
• Front Panel & Remote Controls
| 10
REMOTE CONTROL OPERATION RANGE
LOADING BATTERIES
| 11
| 11
• Preliminary Knowledge About Discs
PLAYABLE DISC TYPES
| 12
REGION CODE
| 12
NOTES ON COPYRIGHT
| 12
SYMBOL ABOUT INVALID OPERATION
| 12
AUDIO AND VIDEO FILES
| 13
CARE AND HANDLING OF DISCS
| 13
• Operations
BASIC PLAYBACK
| 14
DISPLAYING DISC INFORMATION DURING PLAYBACK
PLAYING THE DESIRED SECTION OF DISC
| 21
PLAYING A SPECIFIC ITEM
| 22
REPEAT PLAYBACK
| 23
PLAYING TRACKS/FILES IN RANDOM ORDER
| 24
PLAYING TRACKS IN DESIRED ORDER
| 25
BOOKMARK PLAYBACK
| 26
CHANGING THE AUDIO LANGUAGE
| 27
CHANGING THE SUBTITLE LANGUAGE
| 27
CHANGING THE CAMERA ANGLE
| 28
ZOOMING IN/OUT A SCENE
| 28
CHANGING THE VIDEO SIGNAL FORMAT
| 29
CHANGING THE COMPONENT VIDEO OUTPUT SIGNAL
• Initial Settings
| 30
SETTING THE LANGUAGE SETUP | 31
SETTING THE VIDEO SETUP | 33
SETTING THE AUDIO SETUP | 36
SETTING THE SPEAKER SETUP | 38
SETTING THE OTHER SETUP | 43
• Definition Of Terms
| 49
• Troubleshooting Guide
• Specifications
| 51
| 52
• DVD Language Code List
| 53
5
| 20
| 29
| 9
System Connections
• Do not connect the AC input cord into the AC outlet when plugging and unplugging connection cords.
• Since different components often have different terminal names, carefully read the operating instructions of the component
connected.
• Be sure to observe the color coding when connecting audio and video cords.
• The supplied cords are a (stereo) audio cord, a composite video cord, a system control cord and a power cord. Other cords
are commercially-available cords.
CONNECTING TO A/V AMPLIFIER OR RECEIVER
(COMPOSITE)
VIDEO IN
S-VIDEO IN
Additional TV, etc.
L R L R CENTER SUBFRONT SURROUND
WOOFER
5.1 CH AUDIO IN
L
R
AUDIO IN
OPTICAL COAXIAL S-VIDEO (COMPOSITE) Y Cb/Pb Cr/Pr
IN
VIDEO IN
COMPONENT
DIGITAL INs
VIDEO IN
(MONITOR)
VIDEO OUT
COMPONENT, S-VIDEO, COMPOSITE
SPEAKERS
VIDEO IN
TV
A/V Amplifier or Receiver
FRONT L/R, CENTER, SURROUND L/R, SUBWOOFER, etc.
Speakers
6
1. Connecting 5.1CH AUDIO OUTPUTs
• To fully enjoy the multichannel audio of DVD Audio and
SACD as well as Dolby Digital and DTS soundtracks of
DVD Video, etc., connect these jacks to the corresponding
channel input jacks of your amplifier/receiver.
• When your amplifier/receiver is not compatible with the
digital signals that are output from this unit, loud noise or no
sound may be heard from the speakers, and it may be
harmful to your ears and damages the speakers. To
prevent it, you should set the DIGITAL OUTPUT to OFF
and make analog audio connections. (Refer to “When
selecting the DIGITAL OUTPUT” on page 36.)
• When making the COAXIAL DIGITAL connection, be sure
to use a 75Ω COAXIAL cord, not a conventional AUDIO
cord.
Notes :
• When connecting only the 5.1CH AUDIO OUTPUTs to your
amplifier/receiver, you should set the DOWNMIX to OFF to
output the multichannel audio signals from these jacks as it
was recorded.
In this case, only the front left and right signals of the
multichannel audio signals will output from the 2CH AUDIO
OUTPUT jacks (and the A/V SCART OUTPUT connector).
(For details, refer to “When selecting the DOWNMIX” on
page 36.)
• When connecting the 5.1CH AUDIO OUTPUTs to the
multichannel audio inputs of an amplifier/receiver that dose
not have the speaker setup for the multichannel audio
inputs, you should set the SPEAKER SETUP.(For details,
refer to “SETTING THE SPEAKER SETUP” on page 38.)
• All of the commercially-available optical fiber cords cannot
be used for audio equipments. If there is an optical fiber
cord which cannot be connected to your audio equipments,
consult your dealer or nearest service organization.
Audio output from the unit’s DIGITAL OUTPUTs
• When the DIGITAL OUTPUT is set to ON, the following
table shows that the digital signals can be output from the
DIGITAL OUTPUTs.(For details, refer to “When selecting
the DIGITAL OUTPUT” on page 36.)
Disc type
2. Connecting 2CH AUDIO OUTPUTs
• Connect these jacks to the AUDIO IN jacks of DVD(, AUX,
CD, etc.) of your amplifier/receiver.
• Depending on whether these jacks to a stereo amplifier /
receiver or an A/V amplifier/receiver with built-in surround
decoder, you should set the DOWNMIX to Lo/Ro or
Lt/Rt.(For details, refer to “When selecting the DOWNMIX”
on page 36.)
Audio recording format
Dolby Digital
DVD Video
DVD Audio
DTS
Audio output
Dolby Digital bitstream
DTS bitstream
Linear PCM 48kHz/16~24bit
48kHz/16~24bit PCM
96kHz/16~24bit
96kHz/16~24bit PCM
Linear PCM or Packed PCM
DSD (SACD Area)
SACD
44.1kHz/16bit Linear PCM
Audio CD
44.1kHz/16bit Linear PCM
44.1kHz/16bit PCM
(CD Area)
3. Connecting DIGITAL OUTPUTs
• To enhance the sound quality, connect either the OPTICAL
or the COAXIAL DIGITAL OUTPUT jack to the
corresponding DIGITAL INPUT jack of your
amplifier/receiver with built-in Dolby Digital or DTS decoder.
(You don’t need to do both.)
When DVD Video, etc. recorded in Dolby Digital or DTS is
played, you can enjoy high-quality surround sound.
• To be output digital audio signals from the DIGITAL
OUTPUT jacks, you should set the DIGITAL OUTPUT to
ON. (For details, refer to “When selecting the DIGITAL
OUTPUT”on page 36)
Notes :
• The DIGITAL OUTPUT jacks cannot output the digital
audio signals of DVD Audio and SACD.
Therefore, to be able to play multichannel DVD Audios and
SACDs, you should also connect the 5.1CH AUDIO
OUTPUTs.(Refer to “Connecting 5.1CH AUDIO
OUTPUTs” above)
• If your amplifier/receiver doesn’t have 5.1CH AUDIO
INPUTs, make a stereo analog connection . (Refer to
“Connecting 2CH AUDIO OUTPUTs” above.)
• In order to be able to hear multichannel sound from DVD
Audio and SACD, you should set DVD AUDIO AREA to
DVD AUDIO and SACD AREA to MULTICHANNEL.(Refer
to “When selecting the DVD AUDIO AREA” and “When
selecting the SACD AREA” on page 44.)
• It is not recommended to record digital audio signals with
digital audio connection between this unit and MD or CD
recorder, etc.
When recording the sounds played on this unit, record them
through the 2CH AUDIO OUTPUT jacks.
7
44.1kHz/16bit PCM
MP3 disc
MP3
44.1, 48kHz/16bit PCM
WMA disc
WMA
44.1, 48kHz/16bit PCM
DivX disc
MP3
44.1, 48kHz/16bit PCM
7. Connecting DIGI-LINK jack
• Connect this jack to the DIGI LINK jack of the external
Sherwood component that uses the DIGI LINK II or III
remote control system.
4. Connecting COMPOSITE VIDEO OUTPUTs 1, 2
• Connect this jack to the (composite)VIDEO input jack of
your amplifier/receiver or TV.
• The same signal is output from COMPOSITE VIDEO
OUTPUT 1 and 2 jacks, enabling connection to two
devices(e, g., an A/V amplifier and additional TV)
simultaneously.
Sherwood component
with DIGI LINK II or III
Amplifier/receiver
5. Connecting S-VIDEO OUTPUTs 1, 2
• Connect this jack to the S-VIDEO input jack of your
amplifier/receiver or TV
• The same signal is output from S-VIDEO OUTPUT 1 and 2
jacks, enabling connection to two devices(e, g., an A/V
amplifier and additional TV) simultaneously.
Tape deck
System
control
cord
CD player
8. A/V SCART OUTPUT CONNECTOR(Regional Option)
• Refer to “CONNECTING TO TV WITH SCART
CONNECTOR (Regional Option)” on next page.
6. Connecting COMPONENT VIDEO OUTPUTs
The COMPONENT VIDEO OUTPUTs of this unit are capable
of outputting either conventional interlacing video signal or
progressively scanned video signal(that can reproduce highdensity pictures with less flicker).
9. AC INPUT
• Plug the supplied power cord into this AC INPUT and then
into the wall AC outlet.
• According to VIDEO OUTPUTs, the excellence in picture
quality is as follows:
Progressive “COMPONENT” > Interlaced “COMPONENT”
> “S-VIDEO” > “COMPOSITE”
• When making COMPONENT VIDEO connections, connect
“Y” to “Y”, “Pb” to “Pb”(, “Cb”, “B-Y”), “Pr” to “Pr” (, “Cr”, “R-Y”).
Notes:
• When the VIDEO OUTPUT is set to PROGRESSIVE, the
S-VIDEO and COMPOSITE VIDEO OUTPUTs can not
output the video signals, meaning the picture will not be
shown.
• When the progressive video signals are input into the nonprogressive COMPONENT VIDEO INPUTs of your TV, the
picture may not be shown normally.
Therefore, when the progressive COMPONENT VIDEO
INPUTs of TV are not connected to, you should set the
VIDEO OUTPUT to INTERLACED.(For details, refer to
“When selecting the VIDEO OUTPUT” on page 34.)
• Do not connect the unit to the TV through a VCR.
Otherwise the picture may be disturbed due to the copy
protection function.
• CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE “STANDARD
DEFINITION” OUTPUT. IF THERE ARE QUESTIONS
REGARDING OUR TV SET COMPATIBILITY WITH THIS
MODEL 525p AND 625p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTER.
8
CONNECTING TO TV WITH AUDIO AND VIDEO INS
• You can enjoy DVD Videos by simply connecting this unit to a TV. To hear improved audio sound quality, connect the 2CH
AUDIO OUTPUTs to the AUDIO INs of DVD(, AUX, CD, etc.) of your amplifier/receiver.
• To connect these jacks correctly, refer to “Connecting 2CH AUDIO OUTPUTs” on page 7, “Connecting COMPOSITE VIDEO
OUTPUTs 1, 2” and so forth on page 8.
Notes:
• If your TV has a monaural audio input instead of stereo, you need to use an optional audio cord which converts stereo audio
output to monaural.
• Do not connect the VIDEO OUTs of the unit to the TV through a VCR. Otherwise the image may be disturbed due to the
copy protection function.
Amplifier or Receiver
L
AUDIO
IN
R
This unit
TV, projector, etc.
COMPONENT
VIDEO IN
Y Cb/Pb Cr/Pr
S-VIDEO
IN
L
AUDIO
IN R
(COMPOSITE)
VIDEO IN
CONNECTING TO TV WITH SCART CONNECTOR(Regional Option)
• For some countries like Europe, the unit incorporates the A/V SCART OUTPUT connector.
• You can connect the unit to TV easily using the SCART connections without other cumbersome audio and video connections.
• During operation of the unit, this connector can deliver either the composite(regular) video, S-VIDEO (Y and C) or RGB video
signals as well as the audio L and R signals.
Notes:
• In this connection, do not connect the unit to the TV through a VCR. Otherwise the image may be disturbed due to the copy
protection function.
• According to the video connections between this unit and TV, etc. and the video input source selected on TV, etc., be sure to
set the SCART VIDEO and the VIDEO OUTPUT to the corresponding settings.
When these are not set correctly, no picture or abnormal picture may be displayed.(For details, refer to “When selecting the
VIDEO OUTPUT” and “When selecting the SCART VIDEO(Regional Option)” on page 34.)
This unit
TV
A/V SCART IN
9
Front Panel & Remote Controls
Front Panel Controls
1. POWER switch
2. STANDBY indicator
3. FORWARD/BACKWARD SKIP
(▶▶ / ◀◀) buttons
4. STOP( ) button
5. PAUSE/STEP( ) button
6. PLAY(▶) button
7. OPEN/CLOSE(▲) button
8. DISC TRAY
9. SACD indicator
10. DVD AUDIO indicator
11. PURE AUDIO indicator
12. REMOTE SENSOR
13. FLUORESCENT DISPLAY
• For details, see next page.
Remote Controls
1. POWER ON button
2. STANDBY button
3. OPEN/CLOSE(▲) button
4. DIMMER button
5. DISPLAY button
6. NTSC/PAL button
7. UPSCALE button
8. SEARCH button
9. MARKER button
10. NUMERIC (0~9, +10) buttons
11. CLEAR button
12. REPEAT(
) button
13. REPEAT A/B button
14. PROGRAM button
15. RANDOM PLAY button
16. AUDIO button
17. SUBTITLE button
18. ZOOM button
19. ANGLE button
20. SACD AREA button
21. PURE AUDIO button
22. TOP MENU button
23. MENU button
24. CURSOR CONTROL(▲/▼/◀/▶), ENTER buttons
25. SETUP button
26. RETURN button
27. STOP button
28. PLAY button
29. PAUSE/STEP button
30. SCAN ◀◀/▶▶ buttons
31. SKIP ◀◀/ ▶▶ buttons
32. PAGE ∨/ ∧ buttons
33. TITLE/GROUP ∨/ ∧ buttons
10
Fluorescent Display
PLAY Indicator
DISC TYPE
indicators
SOUND RECORDING SYSTEM
indicators
PROGRESSIVE indicator
PURE AUDIO indicators
VIDEO FILE TYPE
indicators
SOUND RECORDING SYSTEM
indicators
PAUSE
indicator
REMAIN indicator
ANGLE indicator
REPEAT indicators
Group/title number,
track/chapter number,
playing time, operating
information, etc.
RANDOM indicator
PROGRAM indicator
SOUND RECORDING
SYSTEM indicator
REMOTE CONTROL OPERATION RANGE
AUDIO FILE TYPE indicators
CHANNEL indicators
LOADING BATTERIES
1
2
Remove the cover.
Load two batteries (“AAA” size, 1.5V)
matching the polarity.
• Use the remote control unit within a range of about
7 meters (23 feet) and angles of up to 30 degrees
aiming at the remote sensor.
Note:
• Remote operation may become unreliable if the
REMOTE SENSOR is exposed to strong light
such as direct sunlight or inverted fluorescent.
• Remove the batteries when they are not used for a
long time.
• Do not use the rechargeable batteries(Ni-Cd type).
11
Preliminary Knowledge About Discs
PLAYABLE DISC TYPES
REGION CODE
This unit supports the following discs.
Disc
Logo
Format or file type
DVD Video
DVD Video
DVD Audio
DVD Audio
SACD
DVD-R
• DVD players and DVD Videos have their own Region Code
numbers which are assigned to each country or area as
shown below. DVD players are set to your Region Code
number at the factory. As a result, if the region code
number of this DVD player is different from that of the DVD
Video, playback of the DVD Video will not be allowed by
the DVD player.
Major
countries
or area
Super Audio CD
(Single layer, Dual layer,
Hybrid)
All
regions
North
America
Europe,
Japan,
Middle East
Southeast
Asia
Oceania,
South
America
Russia
China
Playable
Region
code
DVD Video, DivX
Examples of playable DVD Videos :
DVD-RW
DVD Video, DivX
DVD+R
DVD Video, DivX
DVD+RW
DVD Video, DivX
• In U.S.A .
• In Europe
NOTES ON COPYRIGHT
Audio CD
PCM
CD-R
Audio CD, MP3, WMA,
JPEG, DivX
CD-RW
Audio CD, MP3, WMA,
JPEG, DivX
JPEG CD
JPEG
MP3 CD
MP3
• Please check the copyright laws in your country to record
from DVD, Audio CD, MP3, WMA, JPEG and DivX discs, etc.
Recording of copyrighted material may infringe copyright
laws.
• Commercial DVD Video discs are copy-protected, and any
recordings made from these discs will be distorted.
• This product incorporates copyright protection technology
that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection technology
must be authorized by Macrovision, and is intended for
home and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or
disassembly is prohibited.
• This unit supports CD-R and CD-RW discs recorded in
audio CD format or MP3/WMA/JPEG/DivX in accordance
with the ISO9660 format. It also supports DVD-R, DVDRW, DVD+R and DVD+RW discs recorded in DVD Video
format or DivX in accordance with UDF format.
SYMBOL ABOUT INVALID OPERATION
Unplayable discs
• Since this unit cannot support disc types, formats and file
types not listed above, do not play such discs.
• Some DVD+RWs/DVD+Rs, DVD-RWs/DVD-Rs or CDRs/CD-RWs cannot be played due to incomplete disc
finalization, recording quality or physical condition of the
disc, characteristics of recording device or authoring
software, etc.
See the operating instructions supplied with your recording
device for more information.
• When you press a button, if the unit does not accept its
operation,
appears on the TV screen.
Operations are occasionally unacceptable even if
is
not displayed.
※Invalid operation may occur as expected if :
• The region code number of the unit is different from that of
the DVD Video and playback will not be allowed.
• The rating level function works.
(For details, refer to “When selecting the PARENTAL
CONTROL” on page 45.)
• A disc is not playable or uses features that are not
supported by this unit.
Color system format
• Depending on the countries, this unit conforms to either the
NTSC color system for U.S.A, Canada, etc. or the PAL for
Europe, Australia, China, etc.
12
AUDIO AND VIDEO FILES
CARE AND HANDLING OF DISCS
• Folder and file names are displayed up to 11 characters.
• Characters except “A~Z”, “0~9”, “ - ” may be not displayed.
• The playback order of folders and files shown in the menu
may differ from the order shown in a PC.
• This unit supports multi-session discs. Some multi-session
discs may take a long time to load and some may not be
loaded at all.
• In handling a disc, hold it carefully
with edges.
• Do not stick paper or write
anything on the printed surface.
Notes for making a private disc.
• Use “UDF format” as the disc format for DVD-R/DVD-RW,
DVD+R/DVD+RW.
• Use “ISO 9660” as the disc format for CD-R/CD-RW.
• Folders can be up to eight levels deep.
• Some disc may not play due to disc characteristics,
recording conditions, etc.
• Fingermarks and dust on the
recorded surface should be
carefully wiped off with a soft cloth.
Wipe straight from the inside to the
outside of the disc.
MP3
• MP3 files must have a “.mp3” or “.MP3” file name
extension.
• It is recommended that you record your material at a
44.1kHz sampling rate, using the 128 kbps data transfer
rate.
• Fixed bit-rate files are recommended. Variable bitrate(VBR) files are playable, but playing time may be
displayed incorrectly.
• ID3 Tag is not available.
• MP3i and MP3 Pro are not available.
• Always keep the discs in their
cases after use to protect them
from dust and scratches.
JPEG
• JPEG files must have a “.jpg”, “.JPG”, “.jpeg” or “.JPEG”
file name extension.
• It is recommended that you record your material at a
640X480 pixel resolution.
• This unit cannot play a baseline JPEG file of more than
6000X4500 pixels and a progressive JPEG file of more
than 5120X3840 pixels.
• Do not use a cracked, deformed, or repaired disc.
These discs are easily broken and may cause serious
personal injury and apparatus malfunction.
DivX
• DivX files must have a “.divx”, “.DIVX”, “.div”, “.DIV”, “.avi”
or “.AVI” file name extension.
• This unit supports DivX 5.x, 4.x and 3.11
• This unit supports DivX files whose resolution is 640X480
pixels or less.
• Audio stream supports MPEG Audio Layer 3(MP3), WMA
or AC-3, etc..
• This unit does not support GMC(Global Motion
Compression) and Q-Pel(Quarter Pixel).
• This unit has its own Registration Code for DivX playback.
If necessary, you can confirm the registration code of your
unit.(For details, refer to “When selecting the DIVX VOD”
on page 47.)
Notes:
• Because the temperature inside this unit is very high, in
case of no further playback of disc, unload the disc to
prevent the high temperature from deforming the disc.
• Do not expose discs to direct sunlight, high humidity or
high temperature for a long time.
• When loading or unloading a disc in the disc tray, always
place it with the printed side up.
Printed side
WMA
• WMA files must have a “.wma” or “.WMA” file name extension.
• It is recommended that you record your material at a bit
rate of 64 kbps or higher.
• WMA Tag is not available.
• This unit cannot play copyright protected files and files
recorded with a bit rate under 32kbps.
13
Operations
Before starting playback
• Make the initial settings to suit your usage conditions the very first time this unit is turned on.(For details, refer to “Initial
Settings” on page 30)
• For explanation purposes, this instructions explains the OSD(On-Screen Display) language displayed on TV in English.
• Usable discs for each operation/ function are referred to by the icons;
BASIC PLAYBACK
Preparations
• Turn on the TV and select the video input source connected to the unit.
• When you want to enjoy the sound of disc from the audio system, turn on the audio system and select the input source
connected to the unit.
1
2
3
Before operation, enter the standby mode.
Main unit
• The STANDBY indicator lights up in amber. This means
that the unit is connected to the AC mains and a small
amount of current is retained to support operational
readiness.
• To turn the power completely off, press the POWER
switch again.
In the standby mode, turn the power on.
RC
• Press the POWER ON button, then the unit is turned on
to enter the operating mode and the STANDBY indicator
lights up in blue.
• In the operating mode, to enter the standby mode, press
the STANDBY button.
Open the disc tray to load a disc with the printed side up,
then close it.
Main unit
• 8 cm (3 inch) discs can be loaded on the inside circle of
the tray, too.
• When a DVD that doesn’t contain any menu is loaded,
playback automatically starts.
RC
or
Notes :
• In case of DVD Audios, when the DVD Audio to be played contains not only DVD Audio content but also DVD Video content,
first be sure to set the DVD AUDIO AREA correctly before playback.(For details, refer to “When selecting the DVD AUDIO
AREA” on page 44.)
• In case of SACDs, when the SACD to be played contains 2 channel and multichannel audio areas, and CD layer, first be sure
to select the preferred area/layer before playback.(For details, refer to “To select a playback area/layer” on page 16.)
• In case of DivX discs, this unit provides you the DivX® VOD(Video On Demand) registration code that allows you to rent and
purchase videos from DivX® VOD service at www.divx.com/vod.
If necessary, you can confirm the registration code of your unit. (For details, refer to “When selecting the DIVX VOD” on page
47.)
• Depending on the disc types, it may take times to read the loaded disc.
14
• When you load a MP3, WMA, JPEG, DivX disc or a DVD that contains a menu, the menu display may appear on the TV
screen. In this case, see “To start playback from the menu of DVD” below or “To start playback from the menu of MP3,
WMA, JPEG or DivX disc” on the next page.
• Example of DVD Video
• Example of MP3 disc
TITLE MENU
SMART NAVI
Dogs
Cats
Cows
Horses
ROOT
Root menu
ROOT
0
POPS
1
BLUES
2
HAPPY
3
SO LONG
4
CLASSIC
5
LIGHT-M
6
BIRTHDAY
7
Folder and file menu
MP3 file symbol
Folder symbol
4
In case of SACD or CD, press the PLAY(▶)
button to start play.
Main unit
• When a SACD contains the information on track,
album and artist, etc., the corresponding information
will be displayed or not on the TV screen depending
on the OSD setting.(For details, refer to “When
selecting the OSD” on page 44.)
RC
or
To start playback from the menu of DVD
• To select the preferred item, press the CURSOR ▲/▼/◀/▶ buttons and press the ENTER button (or PLAY(▶) button), or
press the NUMERIC buttons.
RC
In case of use of the NUMERIC buttons on the
remote control :
RC
• When selecting “3” :
• When selecting “10” :
• When selecting “21” :
• Playback of the selected item starts.
• In case of selecting the item with pressing the NUMERIC buttons, depending on the discs, the PLAY(▶)(or ENTER) button
should be pressed to start playback of the item.
• Depending on the discs, the preferred item may not be selected with pressing the NUMERIC buttons.
• When the selected item contains the subitems, repeat the above step until the preferred item is selected.
To stop playback and return to the menu display
• Press the TOP MENU or MENU button on the remote control.(Which button is pressed differs depending on the discs.)
• Playback is suspended and the menu display appears.
15
To start playback from the menu of MP3, WMA, JPEG or DivX disc
1
2
In the stop mode, press the CURSOR ◀/▶ buttons to select the folder and file menu.
RC
Press the CURSOR ▲/▼ buttons to select the preferred folder or file then press the ENTER button.
RC
RC
• When selecting the preferred file, playback starts from the
selected file.
• When selecting the preferred folder, the file menu screen
of the selected folder is displayed. In this case, repeat this
step to select the preferred file in its file menu.
Notes:
• To play a MP3/WMA/JPEG/DivX disc with the various playback modes, select the desired playback mode.(For details, refer to
“Repeating a file, folder” on page 23.)
• Some discs/files recorded in DVD Video, MP3, WMA, JPEG or DivX, etc. cannot be played due to incomplete disc finalization,
recording quality or physical condition of the disc, characteristics of recording device or authoring software, etc.
• The DVDs continue to rotate while the menu display appears. When no further selections are to be played, be sure to press
the STOP( ) button repeatedly to enter the stop mode and to clear the menu display.
• A TV screen may be burned out if a static picture is displayed for a long time in the stop mode. To prevent this, set the
SCREEN SAVER to ON (refer to “When selecting the SCREEN SAVER” on page 43). Then, the unit automatically activates
the screen saver function if a static picture, etc. is displayed for over 5 minutes.
Pressing any button will cancel the screen saver function and return to the previous display.
• When you press a button, if the corresponding operation is prohibited by the unit or the disc,
appears on your TV screen.
To select a playback area / layer
• Some SACDs consist of 2 channel and multichannel audio areas, and hybrid SACDs comprise 2 layer structure of an
HD(SACD) layer and CD layer. You can select the desired area/layer to be played. (For details, see the disc’s sleeve notes.)
• This operation works only with SACDs on which 2 areas or/and 2 layers are recorded.
Therefore, when the disc does not contain the preferred channel area or CD layer, you cannot select it.
• You can set the SACD area to the desired at initial settings, too.(For details, refer to “When selecting the SACD AREA” on
page 44.)
• In the stop mode
RC
• Each time this button is pressed, the playback area/layer changes and is
displayed on the TV screen for several seconds as follows :
MULTI CHANNEL MODE : When playing the multichannel area(of HD layer.)
TWO CHANNEL MODE : When playing the 2 channel area(of HD layer.)
CD LAYER : When playing the CD layer.
• After selecting the preferred area or the CD layer, press the PLAY(▶) button
to play the selected.
• Each time the layer changes from HD(SACD) layer to CD layer and vice
versa, it takes several seconds and CHANGE LAYER is displayed.
16
To stop playback
Main unit
• When playback of a DVD is stopped, the unit memorizes
the point where the STOP( ) button was
pressed(RESUME function: DVD only).
(“RESUME” is displayed on the unit’s display when this
function is activated.)
• Press the PLAY(▶) button again, and playback will resume
from this point. When the STOP( ) button is pressed
again, the RESUME function will be canceled and it enters
stop mode.(“STOP” is displayed.)
• During playback of a DVD, when the unit is turned off and
on with pressing the STANDBY button and the POWER ON
button, the resume function is activated, too.
RC
or
To pause playback
Main unit
• DVD Video :
The unit will be in the still picture mode.
In case of DVD Audio, it can be in the still picture mode only
for the video part.
• DVD Audio/SACD/CD/MP3/WMA/JPEG/DivX disc :
The unit will be in the pause mode.
RC
or
• To return to normal playback, press the PLAY(▶) button.
Frame advance playback
• In the still picture mode,
Main unit
• Each time the PAUSE/STEP( ) button is pressed, the disc
is advanced by one frame.
• In case of DVD Audio, the frame advance playback is
possible only for the video part.
• To return to normal playback, press the PLAY(▶) button.
RC
or
To select a title/group during playback
• When some DVDs contain more than one title/group, you
can select the desired one.
• Each time the button is pressed, a title/ group is skipped.
RC
To skip
back
To skip
ahead
17
To skip ahead or back during playback
• To skip ahead
Main unit
• Each time the button is pressed, a chapter/track/file is skipped.
• In case of DVD, SACD and CD, when the BACKWARD
SKIP button is pressed once midway through a
chapter/track, playback returns to the beginning of that
chapter/track. When it is pressed again, a chapter/ track is
skipped.
• You can select a chapter/track/file directly with pressing the
NUMERIC buttons on the remote control.
• To skip back
RC
Main unit
RC
or
or
Examples) For “3” :
For “10” :
For “21” :
• In case of selecting a file, you can select a file in the
current folder only.
• In case of JPEG/DivX disc, you can select a file in the stop
mode only.
• Depending on the discs, the desired one may not be
selected.
Rapid playback during playback
• You can play back discs at various speeds.
• Each time the button is pressed, the disc is advanced or
reversed fast at up to 6 step speeds depending on the disc
types.
RC
To reverse
To advance
2X → 4X → 6X → 8X → Off(normal playback)
2X → 4X → 8X → 16X → Off(normal playback)
2X → 4X → 8X → 16X → 32X → 64X → Off(normal playback)
• To return to normal playback, press the PLAY(▶) button.
Slow playback
• Each time the button is pressed, the disc is advanced or
reversed slowly at 3 step speed.
1/2 X → 1/4 X → 1/8 X → Off(normal playback)
• In the still picture mode, you can play back the discs at
various speeds.
RC
To reverse
• In case of DVD Audio, the slow playback is possible only
for the video part.
• To return to normal playback, press the PLAY(▶) button.
To advance
To select a page during playback
• When some DVD Audios contain the information pages
that can include photo galleries, artist biographies, lyrics,
etc., you can select the desired page.
• Each time the button is pressed, the page is changed and
displayed on the TV screen.
• Depending on the disc, the information pages may not be
selected.
RC
18
Bonus group playback
• Some DVD Audios contain an extra bonus group that requires a 4-digit password to access.(For details on 4-digit password,
see the disc’s sleeve notes.)
1
During playback, select the bonus group.
• Then password input screen is displayed.
• Depending on DVD Audios, you can select the bonus
group on the title or DVD menu, too.
• Depending on the disc, the bonus group operation may
vary.
RC
BONUS GROUP INPUT PW:
2
Input the 4-digit password with pressing the NUMERIC
buttons.
Example) When inputting “1011”
• Then the bonus group will be played.
• If you input a wrong password, do it again.
RC
Achieving higher purity of sound quality
• You can turn off all the video-related circuits as well as the digital audio-related circuits to eliminate the possibility of
interference for a pure audio experience when playing audio-only discs.
• Although intended for use with audio discs, this function can also be used to enjoy soundtracks and music on DVD Videos
and DivX discs.
• Each time the PURE AUDIO button is pressed, the pure
audio mode changes and the corresponding indicator
lights up on the unit’s display as follows :
RC
“PURE DIGITAL” lights up: When turning off all the video-related
circuits to enjoy pure digital audio.
“PURE ANALOG” lights up: When turning off all the video-related
circuits and the digital audio-related
circuits to enjoy pure analog audio.
OFF: When turning off the pure audio function.
Adjusting the brightness of the fluorescent display
• Each time the DIMMER button is pressed, the brightness
of the fluorescent display of this unit changes as follows:
→ ON → dimmer → OFF
RC
• In the display OFF mode, pressing any button will restore
the display ON mode.
19
DISPLAYING DISC INFORMATION DURING PLAYBACK
• The unit features the on-screen display function showing disc information.
• Press the DISPLAY button.
RC
• Then the disc information is displayed on the TV screen.
• Each time this button is pressed, the disc information is changed depending on the disc types as follows :
TITLE 01/07 CHAPTER 001/012
: Title/chapter number
or group/track number
Total title/group
Total chapter/track number
number
Current title/group Current chapter/track number
number
TITLE ELAPSED
00:16:25
: Elapsed time of
the title/group
TITLE REMAIN
01:37:32
: Remaining time of
the title/group
CHAPTER ELAPSED
0 0 : 0 0 : 17
: Elapsed time of
the chapter/track
CHAPTER REMAIN
0 0 : 01: 55
: Remaining time of
the chapter/track
AUDIO 1/3 :
D 5.1 ENGLISH
SUBTITLE 01/02 : ENGLISH
TRACK ELAPSED
00:22
: Elapsed time of
the track
TRACK REMAIN
02: 01
: Remaining time of
the track
TOTAL ELAPSED
00:22
: Elapsed time of
the disc
TOTAL REMAIN
70:16
: Remaining time of
the disc
OFF
: Audio/subtitle language
FILE ELAPSED
00:00:34
: Elapsed time of
the file
FILE REMAIN
00:04:25
: Remaining time of
the file
OFF
OFF
• Depending on the disc and some operation status as playback of DVD using a title or DVD menu, etc., the disc information
may not be displayed.
To display additional information on a file
• In the stop mode, press the DISPLAY button after selecting the desired file.
RC
• Then the information on file size, recording conditions, etc. will be displayed.
• To turn off the information, press this button again.
20
PLAYING THE DESIRED SECTION OF DISC
1
During playback, press the SEARCH button.
• Then the search mode is displayed on the TV screen.
• Each time this button is pressed, the search mode is
changed depending on the disc types as follows:
RC
: Title/chapter search mode
or group/track search mode
TITLE 01/ 07 CHAPTER 001 / 012
TIME -- : -- : --
Current title/ Total title/group Total chapter/track number
group number number
Current chapter/track number
: Time search mode
OFF
: Title/time search mode
or group/time search mode
TITLE 01/07 TIME - - : - - : - -
OFF
When selecting the desired search mode while displaying title/chapter, group/track, title/time or group/time search mode.
Press the CURSOR ◀/▶ buttons to select the desired search mode.
RC
• The selected mode is highlighted.
2
Select the section to be played with pressing the NUMERIC buttons on the remote control.
When entering title, chapter, group, track number
When entering the elapsed time
You can play a disc from the desired point by specifying the
elapsed time from the beginning of the current title/group/file.
Examples) For “3 min. 15 sec.” :
Examples) For “3” :
For “11” :
When clearing the numbers entered before playback
• Press the CLEAR button.
For “2 hou. 59 min. 35 sec.” :
RC
• Then the numbers are all cleared.
3
Start playback from the selected section.
Main unit
RC
or
Notes :
• If the title/group/chapter/track/time you entered is not
contained on the disc, search playback will not work.
• Depending on the disc, a search playback will not work or
may work differently.
RC
or
21
PLAYING A SPECIFIC ITEM
When using a title menu
• If some DVDs which contain more than one title may have the menu like as a list of the titles, the TOP MENU button can be
used to select the desired title. (The details of operation differ depending on the disc used.)
1
During playback, press the TOP MENU button.
RC
Example)
• Then a list of titles on the disc is displayed on TV screen.
• If the disc does not have the menu such as a list of titles,
this function does not work.
TITLE MENU
2
Dogs
Cats
Cows
Horses
Press the CURSOR ▲/▼/◀/▶ buttons to select the desired title, then press the ENTER or PLAY(▶) button.
RC
Main unit
RC
or
RC
• The unit starts playback of the selected title.
• When the menu continues onto another screen, repeat
this step until the desired title is selected.
or
When using a DVD menu
• Some DVDs have unique menu structures called DVD menus. For example, the discs programmed with complex contents
provide guide menus, and those recorded with various languages provide menus for audio and subtitle language. Although
the DVD menu’s contents and operation differ from disc to disc, the following explains basic operation when this feature is
used.
1
During playback, press the MENU button.
RC
• Then the DVD menu available on the disc is displayed
on TV screen.
• If the disc does not have the DVD menu, this function
does not work.
Example)
1.AUDIO
2. SUBTITLE
3. ANGLE
2
Press the CURSOR ▲/▼/◀/▶ buttons to select the desired item, then press the ENTER or PLAY(▶) button.
RC
Main unit
RC
or
RC
• The unit starts playback of the selected item.
• When the menu continues onto another screen, repeat
this step until the desired item is selected.
or
22
REPEAT PLAYBACK
• You can play a current title, group, chapter, folder, track, file, disc or part repeatedly.
Note :
• Repeat playback may not work correctly with some discs.
Repeating a chapter/track, title/group
During playback of the desired chapter/track or title/group, press the REPEAT(
) button.
RC
• Then the selected repeat mode is displayed on the TV
screen.
• Each time this button is pressed, the repeat mode changes depending on the disc types as follows :
CHAPTER REPEAT ON
: Chapter/track repeat
REPEAT ONE
: Track repeat
TITLE REPEAT ON
: Title/group repeat
REPEAT ALL
: Entire disc repeat
REPEAT OFF
: Repeat mode off
(normal playback)
REPEAT OFF
: Repeat mode off
(normal playback)
• To return to normal playback, press the REPEAT(
) button repeatedly until the “REPEAT OFF” is displayed.
Repeating a file, folder
1
2
In the stop mode, press the REPEAT(
) button.
RC
• Each time this button is pressed, one of the various
playback modes is selected and displayed on the TV
screen as follows:
REPEAT ONE
: File repeat
FOLDER REPEAT
: Folder repeat
DISC
: Normal playback of the disc
DISC REPEAT
: Entire disc repeat
SINGLE
: Normal playback of a file
FOLDER
: Normal playback of a folder
To select the desired file, perform the steps 1 and 2 in “To start playback from the menu of MP3, WMA, JPEG or
DivX disc” on page 16.
• Playback starts from the selected file according to the selected playback mode.
23
Continued
Repeating the desired part
1
During playback at the beginning of the part you want to repeat, press the REPEAT A/B button.
RC
• Then “A TO B SET A” is displayed on the TV screen.
2
At the end of the part, press the REPEAT A/B button again.
• Then “A TO B REPEAT ON” or “A TO B SET B” is displayed on the TV screen, and the part between points A and B is
played back repeatedly.
• To return to normal playback, press the REPEAT A/B button repeatedly until “A TO B CANCELLED” is displayed.
Notes :
• You may not use the repeat A/B playback of the part that includes multiple camera angles.
• Repeat A/B playback works only within a title or a track.
PLAYING TRACKS/FILES IN RANDOM ORDER
• During playback, press the RANDOM PLAY button.
RC
• Then the selected playback mode is displayed for
several seconds on the TV screen.
• Each time this button is pressed, the playback mode changes depending on the disc types as follows:
RANDOM ON
: Random playback
Track on the disc are played back
in random order.
RANDOM OFF
: Normal playback.
• To return to normal playback, press the RANDOM PLAY button during random playback or in the stop mode, then
“RANDOM OFF” is displayed.
Note :
• Random playback may not work correctly with some discs.
24
PLAYING TRACKS IN DESIRED ORDER
• Up to 25 tracks can be programmed to be played in any desired order.
1
In the stop mode, press the PROGRAM button.
RC
• Then the program mode is displayed on the TV screen.
• When the PROGRAM button is pressed again, the
program mode is canceled.
PROGRAM P 00:00
2
Select the desired track with pressing the NUMERIC buttons on the remote control.
Example) When the track 5 and 12 are programmed.
PROGRAM P 01:05
• For 5 :
• For 12 :
PROGRAM P 02:12
Programmed track number
Programmed order
3
4
Repeat the above step 2 until the desired tracks are programmed.
To start program playback, press the PLAY(▶) button or the ENTER button.
Main unit
RC
or
RC
• Playback will start in the programmed order.
• After all programmed tracks have been played, it enters
the stop mode without clearing the programmed
tracks.(Program playback is suspended.)
or
Clearing the programmed tracks
[ To clear one by one ]
• During programming, press the CLEAR button.
RC
• Each time this button is pressed, the programmed tracks
are cleared one by one in the opposite order.
• Once program playback is performed, you cannot clear
one by one.
[ To clear all programmed tracks ]
• During programming or when the STOP( ) button is
pressed to stop program playback, press the PROGRAM
button.
• Then the programmed tracks are all cleared.
• Opening the disc tray clears all programmed tracks.
RC
25
BOOKMARK PLAYBACK
• The bookmark function allows you to mark the desired scene/point that you can go to quickly.
Up to 14 bookmarks can be stored in the memory.
Storing a bookmark in the memory
1
During playback, press the MARKER button.
Mark mode
RC
• Then the bookmark menu is displayed on the TV screen.
• When the MARKER button is pressed again, the
bookmark menu disappears.
Recall mode
MARK
01
GOTO
01
TOTAL
00/14
Total number of the stored bookmark
The stored bookmark number
The bookmark number to be stored
2
Press the CURSOR ◀/▶ buttons to select the mark mode.
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
mark mode or the recall mode is selected.
3
4
Press the CURSOR ▲/▼ buttons to select the desired bookmark number.
RC
At the desired scene/point, press the ENTER button.
RC
• Then the bookmark is stored in the memory.
• Repeat the above steps 1~4 until the desired scenes/
points are marked.
• When the ENTER button is pressed at a previously used
bookmark number, the new scene/point will be marked
with that bookmark.
Recalling a bookmarked scene/point
1
2
To select the recall mode, perform the above steps 1 and 2.
Press the CURSOR ▲/▼ buttons to select the bookmark number that you want to recall and press the ENTER
button.
RC
• Playback resumes from the scene/point corresponding to
the selected bookmark.
RC
Notes:
• Opening the disc tray or turning the power off clears all
stored bookmarks.
• The bookmark function may not work with some discs.
26
CHANGING THE AUDIO LANGUAGE
• It is possible to change the audio language to a different language from the one selected at the initial settings.
(For details, refer to “SETTING THE LANGUAGE SETUP” on page 31.)
This operation works only with DVDs on which multiple audio languages are recorded.
• During playback, press the AUDIO button.
RC
• Then the audio language menu is displayed on the TV
screen for several seconds.
• Each time this button is pressed, the audio language changes as follows:
Example)
AUDIO 1/3 :
Selected audio
language number
Total number
D
5.1
AUDIO 2/3 :
ENGLISH
D
2CH
ENGLISH
AUDIO 3/3 :
D
2CH
FRENCH
Selected audio language
Sound recording system
Notes:
• You cannot select the preferred audio language when the disc contains only one.
• When the disc is changed, etc., the language heard is the one selected at the initial settings. If this is not recorded on the
disc, only the available language on the disc will be heard.
• On some discs, an audio language except the selected one at the initial settings may be heard.
• In case of some DivX files on which multiple audio languages are recorded, you can also change the audio language with
pressing the AUDIO button.(However, this operation may work differently.)
CHANGING THE SUBTITLE LANGUAGE
• It is possible to change the subtitle language to a different language from the selected one at the initial settings.
(For details, refer to “SETTING THE LANGUAGE SETUP” on page 31.)
This operation works only with DVDs on which multiple subtitle languages are recorded.
• During playback, press the SUBTITLE button
RC
• Then the subtitle language menu is displayed on the TV
screen for several seconds.
• Each time this button is pressed, the subtitle language changes as follows:
Example)
SUBTITLE 01/02 : ENGLISH
Selected subtitle
language number
SUBTITLE 02/02 : FRENCH
Selected subtitle language
SUBTITLE OFF
Subtitle display off mode
Total number
Notes :
• You cannot select the preferred subtitle language when the disc does not contain the available language.
• When the disc is changed, etc., the displayed language is the selected one at the initial settings. If this is not recorded on the
disc, the available language on the disc may be displayed.
• On some discs, a subtitle language except the selected one at the initial settings may be displayed.
• When a disc supporting the closed caption is played, the subtitle and the closed caption may overlap each other on the TV
screen. In this case, turn off the display of subtitle language.
• In case of some DivX files on which multiple subtitle languages are recorded, you can also change the subtitle language with
pressing the SUBTITLE button.(However, this operation may work differently.)
27
CHANGING THE CAMERA ANGLE
• Some DVDs contain scenes which have been shot simultaneously from multiple camera angles.
For these discs, the same scene can be viewed from each of these different angles.
• The recorded angles differ depending on the disc used.
• During playback at the scene recorded from multiple camera angles, press the ANGLE button.
RC
• During playback at the scene recorded from multiple camera
angles, the angle symbol(
) is displayed on the TV
screen only when the ANGLE MARK is set to ON.(Refer to
“When selecting the ANGLE MARK” on page 43.)
• Each time this button is pressed, the angle changes as follows:
Example)
Total number
Selected angle number
Note : This function works only at scenes recorded from multiple angles.
ZOOMING IN/OUT A SCENE
• In the zoom-in mode only, you can select and view any part of the scene close-up.
1
During playback or in the still
picture or the pause mode,
press the ZOOM button.
• Each time this button is pressed, zoom scale or zoom
mode changes as follows:
RC
• The unit zooms in to the center part of the scene.
ZOOM X1.5
ZOOM X2
Zoom-in mode
To select a zoom scale
RC
ZOOM X2
ZOOM OFF
Zoom-in mode
Zoom playback off mode
ZOOM ON
ZOOM OFF
ZOOM X3
ZOOM OFF
Zoom playback off mode
• In the zoom on mode,
• Each time the button is pressed,
zoom scale changes as follows
025 PCT
050 PCT
zoom-out mode
2
100 PCT
150 PCT
200 PCT
zoom-in mode
Only while zooming in a scene,
press the CURSOR ▲/▼/◀/▶
buttons to select the desired
part of the scene.
• To return to the previous operation status, press the
ZOOM button repeatedly until the zoom playback is
canceled.
RC
Notes:
• The zoom function may not work with some discs or files.
• The zoom function may not work properly at some
scenes.
• Zooming is not possible at a title or DVD menu, etc.
28
CHANGING THE VIDEO SIGNAL FORMAT
• Depending on the countries, this unit conforms to either the NTSC color system for U.S.A, Canada, etc., or the PAL for
Europe, Australia, China, etc.
If the color system of this unit is different from that of your TV monitor and the discs to be played, the screen may be
somewhat hard to see or the picture quality may be poor.
Only in this case, change the video signal format to another.
(For details about the video signal format of your TV monitor or the discs, refer to the operating instruction of your TV or the
disc’s jacket.)
• You can set the video signal format to the desired at initial settings, too.
(For details, refer to “When selecting the TV TYPE” on page 33.)
• In the stop mode, press the NTSC/PAL button.
RC
• Each time this button is pressed, the video signal format
changes as follows:
MULTI
NTSC
PAL
• The MULTI is compatible with both NTSC and PAL formats.
CHANGING THE COMPONENT VIDEO OUTPUT SIGNAL
• The COMPONENT VIDEO OUTPUTs of this unit can be capable of outputting either conventional interlacing video signal or
progressively scanned video signal(that can reproduce high-density pictures with less flicker).
• When the COMPONENT VIDEO OUTPUTs of this unit are connected to the COMPONENT VIDEO INPUTs of TV or
projector, etc., depending on whether the video signal system of your TV or projector, etc. supports the conventional
interlacing(simply called interlaced) video signals or the progressively scanned(simply called progressive) video signals(that
can reproduce high-density pictures with less flicker), you should select the corresponding video signal.
• You can set the component video output signal to the desired at initial settings, too.
(For details, refer to “When selecting the VIDEO OUTPUT” on page 34.)
Notes:
• When you select the PROGRESSIVE TV, the S-VIDEO and COMPOSITE VIDEO OUTPUTs of this unit cannot output the
video signals, meaning the picture will not be shown.
• When the progressive video signals are input into the non-progressive COMPONENT VIDEO INPUTs of your TV, etc., the
picture may not be shown normally.
Therefore, when the progressive COMPONENT VIDEO INPUTs of TV is not connected to, you should select INTERLACE
TV.
• In the stop mode, press the UPSCALE button.
RC
• Each time this button is pressed, the component video
output signal changes and “INTERLACE TV” or
“PROGRESSIVE TV” is displayed on the TV screen.
29
Initial Settings
The initial settings of the unit at the factory can be modified as desired later.
Even after the power of the unit is switched to the standby mode, the initial settings are stored in memory until it is changed
the next time.
In the stop mode(“STOP” is displayed on the unit’s
display, not “RESUME”), press the SETUP button
to enter the setup mode.
1
Main setup menu
SETUP MENU - MAIN PAGE
RC
LANGUAGE SETUP
VIDEO SETUP
AUDIO SETUP
SPEAKER SETUP
OTHER SETUP
EXIT SETUP
• To exit the setup mode, press the SETUP button, or press
the CURSOR ▲/▼ buttons to select “EXIT SETUP” on the
main setup menu and press the ENTER button.
2
GO TO LANGUAGE SETUP PAGE
Press the CURSOR ▲/▼ buttons to select a
setting category, then press the ENTER button
to confirm your selection
RC
RC
• Then the selected category will provide you the setting
details using the succeeding screen.
When selecting the LANGUAGE SETUP
When selecting the VIDEO SETUP
LANGUAGE SETUP
VIDEO SETUP
AUDIO
ENGLISH
SUBTITLE
GERMAN
DISC MENUS
FRENCH
OSD LANGUAGE
SPANISH
TV DISPLAY
4:3 PAN-SCAN
TV TYPE
4:3 LETTERBOX
VIDEO OUTPUT
16:9 WIDE
PICTURE MODE
31
SCART VIDEO
OTHERS
33
BLACK LEVEL
MAIN PAGE
MAIN PAGE
When selecting the AUDIO SETUP
When selecting the SPEAKER SETUP
AUDIO SETUP
SPEAKER SETUP
DIGITAL OUTPUT
ON
SPEAKER CONFIGURATION
DOWNMIX
OFF
SPEAKER DISTANCE
CHANNEL LEVEL
DOLBY PRO LOGIC
38
36
AUDIO DRC
MAIN PAGE
MAIN PAGE
When selecting the OTHER SETUP
Note:
• During setting operation, only the STANDBY button and the
buttons required for setting will function.
OTHER SETUP
CAPTIONS
ON
ANGLE MARK
OFF
SCREEN SAVER
BACKGROUND
43
DVD-AUDIO AREA
SACD AREA
PARENTAL
PASSWORD
30
SETTING THE LANGUAGE SETUP
AUDIO : When selecting a preferred audio language to be heard from those
included on the DVD.
SUBTITLE : When selecting a preferred subtitle language to be displayed from
those included on the DVD.
DISC MENUS : When selecting a preferred menu language to be displayed from
those included on the DVD.
OSD LANGUAGE : When selecting a preferred OSD(On-Screen Display) language
to be displayed.
LANGUAGE SETUP
AUDIO
ENGLISH
SUBTITLE
GERMAN
DISC MENUS
FRENCH
OSD LANGUAGE
SPANISH
OTHERS
MAIN PAGE
Item menu
Language menu
Note :
• If the selected language is not recorded in the DVD, one of the recorded languages is automatically selected.
1
Press the CURSOR ▲/▼ buttons to select the preferred item.
Example) When selecting the SUBTITLE
LANGUAGE SETUP
RC
AUDIO
SUBTITLE
OFF
DISC MENUS
ENGLISH
OSD LANGUAGE
GERMAN
FRENCH
MAIN PAGE
SPANISH
OTHERS
• Then the language menu of the selected item is displayed.
2
3
Press the CURSOR ▶ button to select language menu.
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
language menu or the item menu is selected.
Press the CURSOR ▲/▼ buttons to select the preferred language, then press the ENTER button.
RC
RC
• The selected language is colored.
• You can select one of languages listed in the language
menu.
• When you want to select a language other than
languages listed in the language menu, select
“OTHERS”.
• To turn off the display of subtitle language, select “OFF”
on the subtitle language menu.
31
Continued
When selecting “OTHERS”
INPUT LANGUAGE CODE
NEW LANG. CODE:
• Then 4-digit language code input screen is displayed.
• Refer to the “DVD Language Code List” on page 53 to find the 4-digit language code for the preferred language and input it
with pressing the NUMERIC buttons, then press the ENTER button.
Example) When inputting “1428”
RC
• When the 4-digit code is input correctly, the previous menu screen is displayed.
• If you input a wrong code, “INVALID LANGUAGE CODE” is displayed. In this case, input the code again.
4
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶button is pressed, the
item menu or the language menu is selected.
5
Set other setups to your preference.
To return to the main setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ buttons to select “MAIN PAGE” and press
the ENTER button.
Then the main setup menu screen will be displayed.
• When the RETURN button is pressed, the main setup menu screen will be displayed, too.
32
SETTING THE VIDEO SETUP
VIDEO SETUP
TV DISPLAY
4:3 PAN-SCAN
TV TYPE
4:3 LETTERBOX
VIDEO OUTPUT
16:9 WIDE
PICTURE MODE
SCART VIDEO
BLACK LEVEL
MAIN PAGE
Item menu
1
Setting menu
TV DISPLAY : When selecting a picture size according to the aspect ratio of
your TV’s screen
TV TYPE : When selecting the desired video signal format to match that of
your TV monitor and DVD to be played.
VIDEO OUTPUT : When selecting either the conventional interlacing video
signals or the progressively scanned video signals to be
output from the unit’s COMPONENT VIDEO OUTPUTs.
PICTURE MODE : When selecting the picture source mode according to the
type of content being played back.
SCART VIDEO : When selecting the desired video signal(s) to be output from
the unit’s A/V SCART OUTPUT connector.
(Regional option for Europe, etc. only)
BACK LEVEL : When adjusting the intensity of black.
Press the CURSOR ▲/▼ buttons to select the preferred item.
RC
• Then the setting menu of the selected item is displayed.
When selecting the TV DISPLAY
• When you connect a normal TV with 4:3 aspect ratio to the unit, select either “4:3 LETTERBOX” or “4:3 PAN-SCAN” and when you
connect a wide TV with 16:9 aspect ratio, select “16:9 WIDE”.
VIDEO SETUP
TV DISPLAY
4:3 PAN-SCAN
TV TYPE
4:3 LETTERBOX
VIDEO OUTPUT
16:9 WIDE
4:3 PAN-SCAN : DVDs recorded with the 16:9 aspect ratio and the pan-scan
specification are reproduced in the pan-scan screen which
automatically trims the left and right of picture.
4:3 LETTERBOX : DVDs recorded with the 16:9 aspect ratio are reproduced in
the letter box screen which has black bands on the top and bottom.
16:9 WIDE : DVDs recorded with the 16:9 screen are reproduced by filling
the TV screen.
Note: Depending on some DVDs, the playback picture may not conform to
the TV aspect setting you select.
When selecting the TV TYPE
• Depending on the countries, this unit conforms to either the NTSC color system for U.S.A, Canada, etc., or the PAL for
Europe, Australia, China, etc.
If the color system of this unit is different from that of your TV monitor and the discs to be played, the screen may be
somewhat hard to see or the picture quality may be poor.
Only in this case, change the video signal format to another.
(For details about the video signal format of your TV monitor or the discs, refer to the operating instruction of your TV or disc’s
jacket.)
• You can select the desired video signal format with pressing the NTSC/PAL button, too.
(For details, refer to “CHANGING THE VIDEO SIGNAL FORMAT” on page 29.)
VIDEO SETUP
TV DISPLAY
TV TYPE
MULTI
VIDEO OUTPUT
NTSC
PICTURE MODE
PAL
MULTI : When selecting the MULTI that is compatible with both NTSC and PAL
formats.
NTSC : When selecting the NTSC format.
PAL : When selecting the PAL format.
33
Continued
When selecting the VIDEO OUTPUT
• The COMPONENT VIDEO OUTPUTs of this unit can be capable of outputting either conventional interlacing video signal or
progressively scanned video signal(that can reproduce high-density pictures with less flicker).
• When the COMPONENT VIDEO OUTPUTs of this unit are connected to the COMPONENT VIDEO INPUTs of TV or projector, etc.,
depending on whether the video signal system of your TV or projector, etc. supports the conventional interlacing(simply called
interlaced) video signals or the progressively scanned(simply called progressive) video signals(that can reproduce high-density
pictures with less flicker), you should select the corresponding video signal.
• You can select the desired video output signal with pressing the UPSCALE button, too.(For details, refer to “CHANGING THE
COMPONENT VIDEO OUTPUT SIGNAL” on page 29.)
Notes:
• When you select the PROGRESSIVE, the S-VIDEO and COMPOSITE VIDEO OUTPUTs of this unit cannot output the video
signals, meaning the picture will not be shown.
• When the progressive video signals are input into the non-progressive COMPONENT VIDEO INPUTs of your TV, etc., the picture
may not be shown normally.
Therefore, when the progressive COMPONENT VIDEO INPUTs of TV is not connected to, you should select INTERLACED.
INTERLACED : When outputting conventional interlacing video signal.
PROGRESSIVE : When outputting progressively scanned video signal.
VIDEO SETUP
TV DISPLAY
TV TYPE
VIDEO OUTPUT
INTERLACED
PICTURE MODE
PROGRESSIVE
■When selecting the PICTURE MODE
• There are two types of source content in pictures recorded in DVD : film content(pictures recorded from films at 24 frames per
second) and video content(video signals recorded at 30 frames per second).
According to the type of content being played back, select the desired picture mode.
Notes :
• Only when the VIDEO OUTPUT is set to PROGRESSIVE, this setting is valid.
• When there is no improvement in picture quality with the selected picture mode, select the AUTO mode.
PICTURE MODE
AUTO
SCART VIDEO
FILM
BLACK LEVEL
VIDEO
AUTO : Select this mode normally. This unit automatically detects source content,
film or video, of playback source, and perform the necessary signal process.
FILM : When the source content in pictures recorded in DVD is film content.
VIDEO : When it is regular video content.
SMART : When it is content having little movement regardless of the types of content.
SUPER SMART : When it is video content having a lot of movement.
SMART
SUPER SMART
MAIN PAGE
When selecting the SCART VIDEO(Regional Option)
• For some countries like Europe, this unit incorporates the A/V SCART OUTPUT connector which can deliver the composite
(regular), the S-VIDEO(Y and C) or RGB video signals as well as the audio L and R signals for easy connection.
• When the SCART connections between the unit and video equipments are made, you should select the appropriate of the
COMPOSITE, S-VIDEO and RGB video signals.
SCART VIDEO
COMPOSITE
BLACK LEVEL
S-VIDEO
COMPOSITE : When outputting the composite(regular) video signals from
the A/V SCART OUTPUT connector.
S-VIDEO : When outputting the S-VIDEO signals.
RGB : When outputting the RGB signals.
RGB
Notes:
• When the VIDEO OUTPUT is set to PROGRESSIVE, the SCART VIDEO cannot be set to RGB, and vice versa.
• Be sure to set your TV to the corresponding video signal to match the SCART VIDEO setting of the unit.(Refer to the operating
instructions of the component(s) connected.)
• Depending on the SCART VIDEO and VIDEO OUTPUT settings, the video signals will be output as follows:
Relationship between the SCART VIDEO and video output signal settings
SCART
VIDEO
setting
VIDEO OUTs
A/V SCART OUTPUT
COMPOSITE VIDEO
S-VIDEO
COMPONENT
VIDEO OUTPUT setting
VIDEO OUTPUT setting
VIDEO OUTPUT setting
VIDEO OUTPUT setting
“INTERLACED”
“PROGRESSIVE”
“INTERLACED”
“PROGRESSIVE”
“INTERLACED”
“PROGRESSIVE”
“COMPOSITE”
○
×
○
×
○(Interlaced)
○(Progressive)
composite
×
“S-VIDEO”
○
×
○
×
○(Interlaced)
○(Progressive)
S-Video
×
“RGB”
○
×
○
×
×
RGB
×
X: No video signal or abnormal video signal
34
×
“INTERLACED”
“PROGRESSIVE”
Continued
When selecting the BLACK LEVEL
• You can select the desired black level to adjust the intensity of black.
Note :
• Only when the video signal format is NTSC color system, the black level setting is effective for the video signals(other than the
RGB signals(Regional Option for Europe, etc., and the progressive component video signals).
NORMAL : Select this to adjust the black level of the video signal to
the standard level.
DARKER : Select this to adjust the black level darker.
NORMAL
BLACK LEVEL
DARKER
2
Press the CURSOR ▶ button to select the setting menu.
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
setting menu or the item menu is selected.
3
Press the CURSOR ▲/▼ buttons to select the preferred, then press the ENTER button.
RC
RC
• The selected setting is colored.
4
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶button is pressed, the
item menu or the setting menu is selected.
5
Set other setups to your preference.
To return to the main setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ buttons to select “MAIN PAGE” and press
the ENTER button.
Then the main setup menu screen will be displayed.
• When the RETURN button is pressed, the main setup menu screen will be displayed, too.
35
SETTING THE AUDIO SETUP
DIGITAL OUTPUT : When outputting digital audio signal or not.
DOWNMIX : When outputting a preferred analog audio signal format.
DOLBY PRO LOGIC : When turning on or off the Dolby Pro Logic decoder.
AUDIO DRC(Dynamic Range Compression) : When adjusting the dynamic
range compression that makes faint sound easier to hear at low volume
levels.
AUDIO SETUP
DIGITAL OUTPUT
ON
DOWNMIX
OFF
DOLBY PRO LOGIC
AUDIO DRC
MAIN PAGE
Item menu
1
Setting menu
Press the CURSOR ▲/▼ buttons to select the preferred item.
RC
• Then the setting menu of the selected item is displayed.
When selecting the DIGITAL OUTPUT
Notes :
• When playing a SACD(including SACD area in case of hybrid SACDs) or a DVD Audio, no digital signals will be output.
• When your amplifier/receiver is not compatible with the digital signals that are output from this unit, loud noise or no sound
may be heard from the speakers, and it may be harmful to your ears and damages the speakers. To prevent it, you should set
the DIGITAL OUTPUT to OFF and make analog audio connections.
• For details on the digital audio signals that can be output, refer to “Audio output from the unit’s DIGITAL OUTPUTs” on page 7.
AUDIO SETUP
DIGITAL OUTPUT
ON
DOWNMIX
OFF
ON : When outputting the digital audio signals as it was recorded.
(However, there are some exceptions depending on audio recording
format recorded in disc.)
OFF : When outputting no digital audio signals.
When selecting the DOWNMIX
• Depending on how to connect the analog AUDIO OUTPUT jacks to your amplifier/receiver or TV, you should set the
DOWNMIX correctly.
• Depending on whether the 2CH AUDIO OUTPUT jacks (or the A/V SCART OUTPUT connector)to a stereo
amplifier/receiver/TV or an A/V amplifier/receiver with built-in surround decoder, you should set the DOWNMIX to Lo/Ro or
Lt/Rt.
• When playing back a DVD Video, DVD Audio or SACD recorded in multichannel signal format, the DOWNMIX setting affects
the signals output from the 2CH OUTPUT Jacks (and the A/V SCART OUTPUT connector) and the same signals are output
from only the FL and FR jacks of 5.1CH AUDIO OUTPUTs.
• When connecting only the 5.1CH AUDIO OUTPUTs to your amplifier/receiver, you should set the DOWNMIX to OFF to output
the multichannel audio signals from these jacks as it was recorded.
In this case, only the front left and right signals of the multichannel audio signals will output from the 2CH AUDIO OUTPUT
jacks (and the A/V SCART OUTPUT connector).
Note :
• When connecting the 5.1CH AUDIO OUTPUTs to the multichannel audio inputs of an amplifier/receiver that does not have the
speaker setup for the multichannel audio inputs, you should set the SPEAKER SETUP.(For details, refer to “SETTING THE
SPEAKER SETUP” on page 38)
AUDIO SETUP
DIGITAL OUTPUT
DOWNMIX
Lt/Rt
DOLBY PRO LOGIC
Lo/Ro
AUDIO DRC
OFF
Lt/Rt : When enjoying multichannel surround sound by connecting the unit’s
2CH AUDIO OUTPUTs to an A/V amplifier/receiver with built-in surround
decoder.
Lo/Ro : When enjoying conventional 2 channel stereo sound by connecting
the unit s 2CH AUDIO OUTPUTs to a stereo amplifier/receiver/TV
OFF : When outputting the multichannel audio signals from the 5.1CH AUDIO
OUTPUTs as it was recorded.
36
Continued
When selecting the DOLBY PRO LOGIC
• This unit’s built-in Dolby Pro Logic decoder converts 2 channel signals(such as 2 channel Dolby Digital signals of DVD Video
and 2 channel PCM signals of CD, MP3, WMA, DivX) into multichannel(front left, front right, center and surround channel)
signals to which is applied the Dolby Pro Logic surround effect and outputs them from the 5.1CH AUDIO OUTPUT jacks.
Notes :
• When the CENTER SP and SURROUND SP is set to NONE, you cannot enjoy the Dolby Pro Logic surround effect even if the
DOLBY PRO LOGIC is set to ON. (For details, refer to “When selecting the SPEAKER CONFIGURATION” on page 38.)
• Only when the DIGITAL OUT is set to OFF, 2 channel PCM(48kHz/16~24 bit) signals of DVD Video can be converted into
multichannel signals.
• When the DOWNMIX is set to Lt/Rt or Lo/Ro, you cannot select the DOLBY PRO LOGIC.
DOLBY PRO LOGIC
ON
AUDIO DRC
OFF
ON : When turning on the Dolby Pro Logic decoder.
OFF : When turning it off.
When selecting the AUDIO DRC
• This function can be activated, while playing the Dolby Digital program sources only.
DIGITAL OUTPUT
DOLBY PRO LOGIC
AUDIO DRC
MAIN PAGE
2
1~8 : When adjusting the dynamic range compression as desired.
0 : When turning off the dynamic range compression.
8
7
6
5
4
3
2
1
0
DOWNMIX
Note: In some Dolby Digital softwares, this function cannot be available.
Press the CURSOR ▶ button to select setting menu.
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
setting menu or the item menu is selected.
3
Press the CURSOR ▲/▼ buttons to select the preferred setting, then press the ENTER button.
RC
RC
• The selected setting is colored.
4
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶button is pressed, the
item menu or the setting menu is selected.
5
Set other setups to your preference.
To return to the main setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ buttons to select “MAIN PAGE” and press
the ENTER button.
Then the main setup menu screen will be displayed.
• When the RETURN button is pressed, the main setup menu screen will be displayed, too.
37
SETTING THE SPEAKER SETUP
• These settings are valid when the 5.1CH AUDIO OUTPUTs are connected to the multichannel audio inputs of your
amplifier/receiver.(For details, refer to “Connecting 5.1CH AUDIO OUTPUTs” on page 7.)
• To obtain the best possible surround sound, set the size of speakers you have connected and their distances from your
listening position. Then use the test tone to adjust the volume of the speakers to the same level.
Note :
• When the 5.1CH AUDIO OUTPUTs are connected to the multichannel audio inputs of an amplifier/receiver that has its own
speaker size, distance and level settings, set each setting on this setup to default value. Then set the speaker setup on the
amplifier/receiver.
For your reference, each default value is as follows :
* For SPEAKER CONFIGURATION, SUBWOOFER : YES, FRONT / CENTER / SURROUND SP : LARGE, CROSSOVER : 100 Hz
* For SPEAKER DISTANCE, FRONT L/R / CENTER / SURROUND L/R : 3.0 M/10 FT
* For CHANNEL LEVEL, FRONT L/R / CENTER / SURROUND L/R / SUBWOOFER : 0 dB
SPEAKER CONFIGURATION : When setting the size of the speakers that are
connected and the crossover frequency.
SPEAKER DISTANCE : When setting the distance between the listening position
and each speaker.
CHANNEL LEVEL : When adjusting the volume of the speakers with use of
test tone.
SPEAKER SETUP
SPEAKER CONFIGURATION
SPEAKER DISTANCE
CHANNEL LEVEL
MAIN PAGE
When selecting the SPEAKER CONFIGURATION
1
Press the CURSOR ▲/▼ buttons to select the SPEAKER CONFIGURATION, then press the ENTER button.
RC
RC
SPEAKER CONFIGURATION
SUBWOOFER
YES
FRONT SP
NO
CENTER SP
SURROUND SP
CROSSOVER
SPEAKER SETUP
Item menu
Setting menu
CROSSOVER FREQUENCY
• Crossover frequency is the frequency(Hz) below which the bass sound of each speaker is to output from the subwoofer or
from speakers which are set to LARGE(when not using a subwoofer).
• Refer to the operating instructions of the speakers to be connected. If the frequency range of your speaker is 100 Hz~20 kHz,
crossover frequency have to be set to 100 Hz (or slightly higher).
2
Press the CURSOR ▲/▼ buttons to select the preferred item.
RC
• Then the setting menu of the selected item is displayed.
38
Continued
3
Press the CURSOR ▶ button to select the setting menu.
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
setting menu or the item menu is selected.
4
Press the CURSOR ▲/▼ buttons to select the preferred setting, then press the ENTER button.
RC
RC
• The selected setting is colored.
About speaker size
• Depending on your speaker type, you can select one of these following speaker types.
* YES/NO : Select the desired depending on whether a subwoofer is connected or not.
* LARGE : Select this when connecting speakers that can fully reproduce sounds below crossover frequency.
* SMALL : Select this when connecting speakers that cannot fully reproduce sounds below crossover frequency. When this is selected, sounds
below crossover frequency are sent to the subwoofer.
* NONE : Select this when no speakers are connected. When this is selected, sounds are sent to the speakers which are not set to NONE.
• Select LARGE or SMALL not according to the actual size of the speaker but according to the speaker’s capacity for playing
low frequency(bass sound below frequency set for the CROSSOVER FREQUENCE) signals.
• When “SUBWOOFER” is set to “NO”, “FRONT SP” cannot be set to “SMALL”.
• When “FRONT SP” is set to “SMALL”, “CENTER SP” and “SURROUND SP” cannot be set to “LARGE”.
About crossover frequency
• When speakers are set to SMALL, you should set the CROSSOVER FREQUENCY correctly according to their low frequency
playback capacity.
• You can select the preferred within 70~160 Hz.
5
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶button is pressed, the
item menu or the setting menu is selected.
6
Set other speakers to preferred size, etc.
To return to the speaker setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ buttons to select “SPEAKER SETUP” and
press the ENTER button.
Then the speaker setup menu screen will be displayed.
• When the RETURN button is pressed, the speaker setup menu screen will be displayed, too.
7
Set other setups to your preference.
39
Continued
When selecting the SPEAKER DISTANCE
1
Press the CURSOR ▲/▼ buttons to select the SPEAKER DISTANCE, then press the ENTER button.
RC
RC
SPEAKER DISTANCE
UNIT
METERS
FRONT L
FEET
Setting menu
CENTER
Item
menu
FRONT R
SURROUND R
SURROUND L
SPEAKER SETUP
2
Press the CURSOR ▲/▼ buttons to select the preferred item.
RC
• Then the setting menu of the selected item is displayed.
3
Press the CURSOR ▶ button to select the setting menu.
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
setting menu or the item menu is selected.
4
5
Press the CURSOR ▲/▼ buttons to select the
preferred setting, then press the ENTER button.
RC
When selecting the preferred unit,
• You can select either METERS or FEET.
• Once a unit is selected, the distances are automatically
changed in the selected unit.
RC
Press the CURSOR ◀ button to select the item menu.
When setting the distance
• You can set the distance within the range of 1.5~9.0 meters
in 0.3 meter intervals(or 5~30 feet in 1 feet intervals)
Note : You cannot select the subwoofer and speakers set
to NONE.
RC
• Each time the CURSOR ◀ or ▶button is pressed, the
item menu or the setting menu is selected.
6
7
Set other speakers to preferred distances.
To return to the speaker setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ buttons to select “SPEAKER
SETUP” and press the ENTER button.
Then the speaker setup menu screen will be displayed.
• When the RETURN button is pressed, the speaker setup menu screen will be displayed, too.
Set other setups to your preference.
40
Continued
When selecting the CHANNEL LEVEL
1
Press the CURSOR ▲/▼ buttons to select the CHANNEL LEVEL, then press the ENTER button.
RC
RC
CHANNEL LEVEL
TEST TONE
ON
FRONT L
OFF
CENTER
FRONT R
SURROUND R
SURROUND L
SUBWOOFER
Item menu
2
Setting menu
Press the CURSOR ▲/▼ buttons to select the TEST TONE, then press the CURSOR ▶ button to select
the its setting menu.
RC
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
setting menu or the item menu is selected.
3
Press the CURSOR ▲/▼ buttons to select ON, then press the ENTER button.
RC
RC
• Then the test tone function will work.
• When OFF is selected, the test tone function will be
deactivated.
4
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶button is pressed, the
item menu or the setting menu is selected.
5
Press the CURSOR ▲/▼ buttons to select the preferred channel to be adjusted, then press the CURSOR ▶ button
to select its setting menu.
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
setting menu or the item menu is selected.
RC
Note :
• You cannot select the speakers set to NO or NONE.
41
Continued
6
Press the CURSOR ▲/▼ buttons to adjust the volume of the selected speaker as preferred until the sound level of
each speaker is heard to be equally loud.
RC
• You can adjust the volume within the range of -10~0 dB.
7
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶ button is pressed, the
item menu or the setting menu is selected.
8
9
Set other speakers to preferred levels.
After the speakers are all adjusted as preferred, cancel the test tone function.
• Even when the TEST TONE is set to OFF, you can select the preferred channel and adjust its level, too.
To return to the speaker setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ buttons to select “SPEAKER SETUP” and
press the ENTER button.
Then the speaker setup menu screen will be displayed.
• When the RETURN button is pressed, the speaker setup menu screen will be displayed, too.
10
Set other setups to your preference.
42
SETTING THE OTHER SETUP
OTHER SETUP
CAPTIONS
ON
ANGLE MARK
OFF
SCREEN SAVER
BACKGROUND
DVD-AUDIO AREA
SACD AREA
PARENTAL
PASSWORD
Item menu
Setting menu
OSD
ON
DIVX VOD
OFF
DEFAULTS
CAPTIONS : When turning on or off the display of the closed captions
recorded on DVD.
ANGLE MARK : When displaying the angle symbol on the TV screen during
playback at the scene recorded from multiple camera angles.
SCREEN SAVER : When turning on or off the screen saver function.
BACKGROUND : When selecting a preferred background image to be displayed
on the screen in the stop mode and CD play mode.
DVD AUDIO AREA : When selecting a preferred content to be played on some
DVD Audio discs that contain DVD Video content in addition to DVD Audio.
SACD AREA : When selecting a preferred area to be played on some SACDs that
contain multichannel, 2 channel area, and CD layer(in case of hybrid SACDs).
PARENTAL CONTROL : When restricting playback of DVD Video which contains
violent and other scenes according to the level set by the user.
For example, if a movie which includes violent scenes supports the parental lock
feature, such scenes which you do not want to let children view can be cut or
replaced with other scenes.
PASSWORD : When changing the password for parental lock. The unit’s password
has been set to "3308" at the factory.
OSD : When turning on or off the OSD(On-Screen Display) which shows operation
status or disc information, etc.
DIVX VOD : When using the registration code to purchase or rent the videos from
VOD service.
DEFAULTS : When resetting all the settings made in the setup menu except the rating
level, the password and the registration code to the default settings.
When selecting the items other than PARENTAL CONTROL, PASSWORD, DIVX VOD and DEFAULTS
1
Press the CURSOR ▲/▼ buttons to select the preferred item.
RC
• Then the setting menu of the selected item is displayed.
When selecting the CAPTIONS
OTHER SETUP
CAPTIONS
ON
ANGLE MARK
OFF
ON : When turning on the display of the closed captions recorded on DVDs.
OFF : When turning it off.
Notes:
The caption decoder is required to display captions.
DVDs with caption signals are indicated by the
mark.
The captions cannot be displayed when playing DVDs which do not contain
caption signals.
When selecting the ANGLE MARK
ANGLE MARK
ON
SCREEN SAVER
OFF
ON : When turning on the display of the angle symbol(
OFF : When turning it off.
) on the TV screen.
When selecting the SCREEN SAVER
• A TV screen may be burned out if a static picture is displayed for a long time in the stop mode.
To prevent this, set the SCREEN SAVER to ON. Then the unit automatically activates the screen saver function if a static
picture is displayed for over 5 minutes.
Note: The monitor screen of a projector or projection TV is easily burned out if a static picture is displayed for a long time.
Be careful not to allow the monitor screen to be burned out when the SCREEN SAVER is set to OFF.
SCREEN SAVER
ON
BACKGROUND
OFF
ON : When turning on the screen saver function.
OFF : When turning it off.
When selecting the BACKGROUND
BACKGROUND
BLUE
DVD-AUDIO AREA
BLACK
SACD AREA
LOGO
BLUE : When displaying a blue background on the screen.
BLACK : When displaying a black background.
LOGO : When displaying a DVD logo image.
43
Continued
When selecting the DVD AUDIO AREA
• Some DVD Audio discs consist of DVD Video and DVD Audio contents. You can select the desired area to be played.
(For details, see the disc’s sleeve notes.)
Note : When the disc dose not contain the selected one at this menu, the available one will be played regardless of the DVD
AUDIO AREA setting.
DVD-AUDIO AREA
DVD AUDIO
SACD AREA
DVD VIDEO
DVD AUDIO : When playing the DVD Audio content.
DVD VIDEO : When playing the DVD Video content.
When selecting the SACD AREA
• Some SACDs consist of 2 channel and multichannel audio areas, and hybrid SACDs comprise 2 layer structure of an
HD(SACD) layer and CD layer. You can select the desired area/layer to be played.(For details, see the disc’s sleeve notes.)
• You can select the desired area/layer with pressing the SACD AREA button, too. (For details, refer to “To select a playback
area/layer” on page 16.)
Note : When the disc does not contain the selected one at this menu, that cannot be played. Therefore you should select the
desired of the available ones.
SACD AREA
MULTICHANNEL
PARENTAL
2CHANNEL
PASSWORD
CD
MULTICHANNEL : When playing the multichannel area (of HD layer).
2CHANNEL : When playing the 2 channel area (of HD layer).
CD : When playing the CD layer.
When selecting the OSD
• When a SACD contains the information on track, album and artist, etc., the corresponding information will be displayed or not
depending on the OSD setting.
2
OSD
ON
DIVX VOD
OFF
ON : When turning on the OSD(On-Screen Display) which shows
operation status or disc information, etc.
OFF : When turning it off.
Press the CURSOR ▶ button to select the setting menu.
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
setting menu or the item menu is selected.
3
Press the CURSOR ▲/▼ buttons to select the preferred setting, then press the ENTER button.
RC
RC
• The selected setting is colored.
4
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶button is pressed, the
item menu or the setting menu is selected.
5
Set other setups to your preference.
To return to the main setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ buttons to select “MAIN PAGE” and press
the ENTER button.
Then the main setup menu screen will be displayed.
• When the RETURN button is pressed, the main setup menu screen will be displayed, too.
44
Continued
When selecting the PARENTAL CONTROL
1
Press the CURSOR ▲/▼ buttons to select the PARENTAL CONTROL.
OTHER SETUP
RC
CAPTIONS
1G
ANGLE MARK
2
SCREEN SAVER
3 PG
BACKGROUND
4 PG 13
DVD-AUDIO AREA
5
SACD AREA
6 PG-R
PARNENTAL
7 NC-17
PASSWORD
8 ADULT
Level 1G :
Select this to play only DVD Videos for children.
Adult and general audience DVD Videos cannot
be played.
Level 2~7 NC-17 :
Select this to play DVD Videos for general audiences
and children. Adult DVD Videos cannot be played.
Level 8 ADULT :
Select this to play for general audiences,
children and adults.
NO PARENTAL :
Select this to play all DVD Videos.
Notes :
• When you set the rating level low, some discs may not be played at all. In this case, set the rating level higher or to “NO
PARENTAL”.
• DVD Videos may or may not respond to the rating level setting. Make sure this function works with your DVD Videos.
2
3
Press the CURSOR ▶ button to select the level menu.
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
level menu or the item menu is selected.
Press the CURSOR ▲/▼ buttons to select the preferred level, then press the ENTER button.
RC
RC
PASSWORD VERIFY PAGE
INPUT PASSWORD:
4
Input a 4-digit password with pressing the NUMERIC(0~9) buttons, then press the ENTER button.
RC
RC
• When the password is input correctly, the rating level is set to the preferred level and the previous menu screen is displayed.
• If you input a wrong password, “PASSWORD INCORRECT” is displayed. In this case, input the password again.
• While displaying the password verify page screen, when the RETURN button is pressed, the other setup menu screen will be
displayed.
Note : If you forgot your password, input “3308” that has been set to at factory.
5
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶button is pressed, the
item menu or the level menu is selected.
45
Continued
6
Set other setups to your preference.
To return to the main setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ buttons to select “MAIN PAGE” and press
the ENTER button.
Then the main setup menu screen will be displayed.
• When the RETURN button is pressed, the main setup menu screen will be displayed, too.
When selecting the PASSWORD
1
Press the CURSOR ▲/▼ buttons to select the PASSWORD.
RC
PASSWORD
2
CHANGE
Press the CURSOR ▶ buttons to select the CHANGE, then press the ENTER button.
RC
RC
PASSWORD CHANGE PAGE
OLD PASSWORD:
NEW PASSWORD:
CONFIRM :
3
Input 4-digit passwords in sequence for old password, new password and confirmation, then press the ENTER
button.
RC
RC
PASSWORD CHANGE PAGE
OLD PASSWORD:
XXXX
NEW PASSWORD:
XXXX
CONFIRM :
XXXX
• When each password is input correctly, the previous menu screen is displayed.
• While displaying the password change page menu screen, when the RETURN button is pressed, the other setup menu
screen will be displayed.
Note :
• Do not forget the password. When you input the password first time or if you forgot your password, input “3308” that has
been set to at factory for the old password.
4
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶ button is pressed, the
item menu or the setting menu is selected.
46
Continued
5
Set other setups to your preference.
To return to the main setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ button to select “MAIN PAGE” and press the
ENTER button.
Then the main setup menu screen will be displayed.
• When the RETURN button is pressed, the main setup menu screen will be displayed, too.
When selecting the DIVX VOD
• This unit provides you the DivX® VOD(Video On Demand) registration code that allows you to rent and purchase videos from
DivX® VOD service at www.divx.com/vod.(For details, visit it at www.divx.com/vod.)
1
Press the CURSOR ▲/▼ buttons to select the DIVX VOD.
RC
DIVX VOD
CONFIRM
DEFAULTS
2
3
Press the CURSOR ▶ button to select the setting menu, then press the ENTER button.
RC
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
setting menu or the item menu is selected.
• The registration code will be displayed.
• Use the registration code to purchase or rent the videos
from DivX® VOD service.
Note: Only the downloaded videos by using this unit’s
registration code can be played back on this unit.
After confirming the registration code, press the ENTER button.
RC
• The other setup menu screen will be displayed.
4
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶button is pressed, the
item menu or the setting menu is selected.
5
Set other setups to your preference.
To return to the main setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ button to select “MAIN PAGE” and press the
ENTER button.
Then the main setup menu screen will be displayed.
• When the RETURN button is pressed, the main setup menu screen will be displayed, too.
47
Continued
When selecting the DEFAULTS
1
Press the CURSOR ▲/▼ buttons to select the DEFAULTS.
RC
DIVX VOD
RESET
DEFAULTS
2
RESET :
When resetting all the settings in the setup
menu except the rating level, the password
and the registration code to the default
settings.
Press the CURSOR ▶ button to select the setting menu, then press the ENTER button.
RC
RC
• Each time the CURSOR ▶ or ◀ button is pressed, the
setting menu or the item menu is selected.
• The selected setting is colored.
3
Press the CURSOR ◀ button to select the item menu.
RC
• Each time the CURSOR ◀ or ▶button is pressed, the
item menu or the setting menu is selected.
4
Set other setups to your preference.
To return to the main setup menu screen
• Press the CURSOR ◀ button to select the item menu, press the CURSOR ▲/▼ button to select “MAIN PAGE” and press
the ENTER button.
Then the main setup menu screen will be displayed.
• When the RETURN button is pressed, the main setup menu screen will be displayed, too.
48
Definition Of Terms
DVD Video
DVD Video structure
The format for storing MPEG-2 video on DVD, with
interactive menus, multiple soundtracks, subtitles, camera
angles, and so on.
DVD Video discs typically contain one or more titles, which
may be subdivided into chapters.
Title 1
DVD Audio
Chapter 1
The DVD format for storing up to six(5.1) channels of 24
bit/96 kHz digital audio or two channels of 24 bit /192 kHz
digital audio.
Title 2
Chapter 2
Chapter 3
Chapter 1
Chapter 2
DVD Audio structure
DVD Audio discs contain groups and tracks.
SACD(Super Audio CD)
Group 1
SACD uses DSD(Direct Stream Digital) technology for
higher quality sound than standard audio CDs. There are
three types of discs : single layer, double layer and hybrid
discs. The hybrid disc contains both standard audio CD and
Super Audio CD information.
• “Super Audio CD” is a registered trade mark.
Track 1
Group 2
Track 2
Track 3
Track 1
Track 2
SACD/Audio CD structure
SACDs and Audio CDs contain tracks.
Track 1
MPEG(Moving Picture Expert Group)
It is regarded as an international standard for compressing
and restoring digital video and audio signal. “MPEG”
standards include MPEG-1, MPEG-2 and MPEG-4. Video
CD and MP3 are based on MPEG-1, while DVD Video is
based on MPEG-2.
Track 2
Track 3
Track 4
Some SACDs consist of the 2 channel playback area and
the multichannel playback area.
Multichannel area
Track 1
Track 2
2 channel area
Track 3
Track 1
Track 2
MP3
MP3 is an audio data compression format, which stands for
MPEG-1 Audio Layer 3. Using MP3, you can achieve a data
reduction of about 1:10.
• MPEG Layer-3 audio coding technology licensed from
Fraunhofer IIS and Thomson.
MP3/WMA/JPEG/DivX structure
On an MP3/WMA/JPEG/DivX disc, a folder can be a
member of another folder, creating hierarchical folder layers.
If you are familiar with a personal computer, you may easily
understand the hierarchical file/folder construction.
WMA(Windows Media Audio)
Folder
WMA is an audio data compression format developed by
Microsoft Corporation. WMA file size is smaller than that of
MP3.
File
File
File
File
File
Folder’
File
JPEG(Joint Photographic Experts Group)
File
Folder
File
JPEG is a papular file format for still image compression and
storage.
There are three sub-types of the JPEG format as follows.
• baseline JPEG : used for digital cameras, the web, etc.
• progressive JPEG : used for the web.
• lossless JPEG : an old type, rarely used now.
Aspect ratio (DVD)
DviX
Some DVDs contain the recording of more than one subtitle
languages. With these discs, this unit can select one of the
subtitle languages as desired during playback.
The aspect ratio is the ratio between the vertical and
horizontal size of the picture displayed on a TV screen. The
aspect ratio of normal TV screen is 4:3 while that of the
wide-screen TV and HDTV screen is 16:9.
Subtitle (DVD)
DivX is MPEG-4 based video compression technology
developed by DivXNetworks, Inc. It can shrink digital video
to size small enough to be transported over the internet,
while maintaining high visual quality.
• DivX, DivX Certified, and associated logos are trademarks
of DivXNetworks, Inc. and are used under license.
Angle (DVD)
Some DVDs contain scenes which have shot simultaneously
from multiple camera angles. With these discs, the same
scene can be viewed from each of these different angles.
49
Interlaced scan
Dolby Digital
In the conventional video system, a picture is shown on the
screen in two halves. The interlaced scanning system places
lines of the second half of the picture in-between lines of the
first half of the picture.
Progressive scanning displays all the horizontal lines of a
picture at one time, as a single frame.
Dolby Digital provides multichannel surround sound in
cinemas from 35 mm film and in the home from laser discs,
DVDs, and digital broadcast television, cable, and satellite
systems. It enables the transmission and storage of up to
five full-range audio channels, plus a low-frequency effects
channel(LFE), thus 5.1 channels, in less space than is
required for just one linear PCM-coded channel on a
compact disc.
Composite video
Dolby Pro Logic
A single video signal commonly used in most consumer
video products that contains all luminance, color, and
synchronization information.
Audio signal processing technology developed by Dolby
Laboratories for surround sound.
Dolby Pro Logic process outputs four channel(front left/right,
center, surround) signals.
The surround channel is monaural.
Progressive scan
S-video
A video signal which improves picture quality over the
standard composite video signal.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are
trademarks of Dolby Laboratories.
Component video
Video signals with three channels of separate information
that makes up the picture. There are some types of
component video, such as Y/CB(Pb)/CR(Pr) and R/G/B.
DTS (Digital Theater Systems)
DTS is a newly-developed surround system which can
handle more amount of data, providing better audio quality.
Though the number of audio channels is 5.1 which is same
as Dolby Digital, discs bearing the“
”provides fat
sound and better signal-to-noise ratio, thanks to the lower
audio compression ratio format. It also provides wide
dynamic range and better separation, resulting in
magnificent sound.
Bitstream
The digital signal form of multichannel audio data (e.g., 5.1
channel) before it is decoded into its various channels.
Linear PCM
PCM stands for Pulse Code Modulation. Linear PCM is the
usual digital method without compression, used for audio
playback of audio CDs, DVD Videos, etc.
“DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
50
Troubleshooting Guide
If a fault occurs, run through the table below before taking your receiver for repair.
If the fault persists, attempt to solve it by switching the unit off and on again. If this fails to resolve the situation, consult your
dealer. Under no circumstances should you repair the unit yourself as this will invalidate the guarantee!
PROBLEM
POSSIBLE CAUSE
REMEDY
No power
• The AC input cord is disconnected.
• Poor connection at AC wall outlet or the outlet is
inactive.
• Connect cord securely.
• Check the outlet using a lamp or another appliance.
No playback
• The disc is loaded upside down.
• The disc is not playable.
• The disc is dirty.
• The rating level is not set correctly.
• Reload the disc with the printed side up.
• Use a playable disc.
• Clean the disc.
• Set the rating level setting correctly.
(Refer to “When selecting the PARENTAL
CONTROL” on page 45.)
• Adjust the setting correctly.
(Refer to “SYMBOL ABOUT INVALID OPERATION”
on page 12.)
• The symbol about invalid operation is displayed.
Malfunction
• The disc is scratched, dirty badly or unplayable.
• Press the POWER switch to switch the power off,
press the POWER switch again and then unload the
disc.
No picture
• The video cords are disconnected.
• The incorrect selection of input source on the TV.
• The disc is not playable.
• The PURE AUDIO indicator lights up on the front panel.
• Connect the cords correctly.
• Select the input source correctly.
• Use a playable disc.
• Turn off the pure audio function.
Noisy or distorted
picture
• The unit is connected to a VCR directly and the
copyguard function is activated.
• The disc is dirty.
• It is in rapid advance or reverse playback, or in frame
advance playback.
• Connect the unit so that the picture signal is
transferred directly to the TV.
• Clean the disc.
• Sometimes a small amount of picture distortion may
appear. This is not malfunction.
Abnormal picture or no
picture
• The component video output signal is not selected
correctly.
• Select the component video output signal correctly.
(Refer to “CHANGING THE COMPONENT VIDEO
OUTPUT SIGNAL” on page 29.)
Slight pause of picture
• The layer transition occurs during playback of DVD
Videos recoded in dual-layer format.
• Sometimes slight pause may occur.
This is not malfunction.
No sound
• The audio cords are disconnected.
• The speakers are disconnected to the amplifier.
• The incorrect selection of input source on the amplifier.
• Digital signals are not output from the DIGITAL
OUTPUT jacks.
• Connect the cords correctly.
• Connect the speakers correctly.
• Select the input source correctly.
• Set the DIGITAL OUTPUT to ON.
(Refer to “When selecting the DIGITAL OUTPUT” on
page 36.)
• Make analog audio connection.
• Digital signals cannot be output from a SACD or a
DVD Audio.
Noisy or distorted
sound
• The disc is dirty.
• Poor connections.
• Clean the disc.
• Check the connections and connect all cords
securely.
No playback of DVD
Video contents on a
DVD Audio.
• DVD AUDIO AREA is set to DVD AUDIO.
• Set the DVD AUDIO AREA to DVD VIDEO.(Refer to
“When selecting the DVD AUDIO AREA” on page 44.)
No playback of the
desired area/layer on
a SACD.
• The desired area/layer is not selected.
• Select the desired.(Refer to “To select a playback
area/layer” on page 16.)
Remote control unit
does not operate.
• Batteries are not loaded or exhausted.
• The remote sensor is obstructed.
• Replace the batteries.
• Remove the obstacle.
51
Specifications
• TYPE
System | DVD Video / Audio & SACD player
Laser | Semiconductor laser
• AUDIO SECTION
Frequency response
Sampling frequency : 192 kHz, DVD Audio | 4 Hz ~ 88 kHz
Sampling frequency : 96 kHz, DVD | 4 Hz ~ 44 kHz
Sampling frequency : 48 kHz, DVD | 4 Hz ~ 22 kHz
Sampling frequency : 44.1 kHz, Audio CD | 4 Hz ~ 20 kHz
SACD | 2 Hz~100 kHz
Signal to noise ratio, IHF “A” weighted | 100 dB
Dynamic range
DVD(48 kHz, 24 bit) / SACD / Audio CD | 103 / 108 / 99 dB
Total harmonic distortion, 1 kHz | 0.3 %
Wow and flutter | Unmeasurable (less than ±0.002 %)
Analog output level, 10 kΩ | 2.0 V
Digital output level
Coaxial, 75 Ω | 0.5 Vp-p
Optical, 660 nm | -21 ~ -15 dBm
• VIDEO SECTION
Video compression,
DVD / DivX | MPEG 2 / MPEG 4
Horizontal resolution
DVD Video | 500 lines
Output level, 75 Ω
VIDEO (regular, COMPOSITE) | 1.0 Vp-p
S-VIDEO : Y/C | 1.0 / 0.286 Vp-p
COMPONENT : Y / Pb / Pr | 1.0 / 0.7 / 0.7 Vp-p
A/V SCART(Regional option) : R / G / B | 0.7 / 0.7 / 0.7 Vp-p
• GENERAL
Video signal format | NTSC / PAL
Power supply
U.S.A. and Canada | 120 V~60 Hz
China, Europe, Australia and other countries | 220 - 240 V~50 / 60 Hz
Power consumption | 20 W
Dimension (W x H x D) | 440 x 127 x 356 mm (17-3/8 x 5 x 14 inches)
Weight (Net) | 5.0 kg (11 lbs)
Note : Design and specifications are subject to change without notice for improvements.
52
DVD Language Code List
Code
Language
Code
Language
Code
Language
Code
Language
1027
Afar
1186
Scots Gaelic
1350
Malayalam
1513
Siswati
1028
Abkhazian
1194
Galician
1352
Mongolian
1514
Sesotho
1032
Afrikaans
1196
Guarani
1353
Moldavian
1515
Sundanese
1039
Amharic
1203
Gujarati
1356
Marathi
1516
Swedish
1044
Arabic
1209
Hausa
1357
Malayalam
1517
Swahili
1045
Assamese
1217
Hindi
1358
Maltese
1521
Tamil
1051
Aymara
1226
Croatian
1363
Burmese
1525
Tegulu
1052
Azerbaijani
1229
Hungarian
1365
Nauru
1527
Tajik
1053
Bashkir
1233
Armenian
1369
Nepali
1528
Thai
1057
Byelorussian
1235
Interlingua
1376
Dutch
1529
Tigrinya
1059
Bulgarian
1239
Interlingue
1379
Norwegian
1531
Turkmen
1060
Bihari
1245
Inupiak
1393
Occitan
1532
Tagalog
1061
Bislama
1248
Indonesian
1403
(Afan) Oromo
1534
Setswana
1066
Bengali ; Bangla
1253
Icelandic
1408
Oriya
1535
Tonga
1067
Tibetan
1254
Italian
1417
Punjabi
1538
Turkish
1070
Breton
1257
Hebrew
1428
Polish
1539
Tsonga
1079
Catalan
1261
Japanese
1435
Pashto ; Pushto
1540
Tatar
1093
Corsican
1269
Yiddish
1436
Portuguese
1543
Twi
1097
Czech
1283
Javanese
1463
Quechua
1557
Ukrainian
1103
Welsh
1287
Georgian
1481
Rhaeto-Romance
1564
Urdu
1105
Danish
1297
Kazakh
1482
Kirundi
1572
Uzbek
1109
German
1298
Greenlandic
1483
Romanian
1581
Vietnamese
1130
Bhutani
1299
Cambodian
1489
Russian
1587
Volapük
1142
Greek
1300
Kannada
1491
Kinyarwanda
1613
Wolof
1144
English
1301
Korean
1495
Sanskrit
1632
Xhosa
1145
Esperanto
1305
Kashmiri
1498
Sindhi
1665
Yoruba
1149
Spanish
1307
Kurdish
1501
Sangro
1684
Chinese
1150
Estonian
1311
Kirghiz
1502
Serbo-Croatian
1697
Zulu
1151
Basque
1313
Latin
1503
Singhalese
1157
Persian
1326
Lingala
1505
Slovak
1165
Finnish
1327
Laothian
1506
Slovenian
1166
Fiji
1332
Lithuanian
1507
Samoan
1171
Faeroese
1334
Latvian ; Lettish
1508
Shona
1174
French
1345
Malagasy
1509
Somali
1181
Frisian
1347
Maori
1511
Albanian
1183
Irish
1349
Macedonian
1512
Serbian
53
SD-860
DVD-VIDEO / AUDIO & SACD PLAYER
5707-04736-007-0
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement